‘To avoid copter's damage and player’s ini
read this instruction before fying!
3.5-CHANNEL GYRO SYSTEM
ALLOY INFRARED REMOTE CONTROL HELICOPTER
i)
NO.S107G
«
Balance bar —~
Main blade _ Main blade
Landing gear_—~
Charging socket
Sais arging socket
charger light
Power switch ———) [ll | Power switch
Left/Right/Forward/ €
Backward rudder
control lever
Ly
Throttle
stick
~
Rotation adjustment knob Charging wireBATTERY INSTALLATION & CHARGING
Battery Installation
Transmitter
i Open the cover of battery case
> insert 6 batteries (size AA)
properly followed by polar
indicator, shut the cover of
6X15VAA_- battery case
batteries
Batter cover
Charging Helicopter
A. controller charging B, USB charging
oF
1 computer
4. USB port
1. Move the power switch on the helicopter to the "OFF" position.
2. Charging way A: Put down the charging wire cover of the back controller and
put out the charging wire, then put into the interface of the helicopter, the green
light on the conrtoller will change red. The charging time is about 40-50 minutes
The glisten red light will to change normal light. Then the helicopter is fully"
charged.
Charging way B: Put the USB charging wire into the computer USB interface,
the charging wire will be light. Put the other side of USB charging wire into the
helicopter’s interface, USB charging wire light will be turn off. The charging
time is about 40-50 minutes. Charging wire light will tum on.
Then the helicopter is fully charged.
FLYING YOUR HELICOPTER
- Set the Band Selector on the Transmitter and Helicopter to the same frequency.
- Move the Power Switch on the helicopter to the ON position, the power
indicator will light up.
- Place the helicopter on the ground with the tail pointed towards you.
- When the helicopter received the transmit,the led of circuit board will turn light.
1, Trun on the switch.
| 2. The motive handle (acclerator) must be pushed to the
maximum control route of travel first, then adjust it to
zero (lowest), after that, you can turn on the power of
helicopter to fly the normal operation.
MANIPULATEOm een mg ST eee mee TKS
When the helicopter fllies steadity,you can | Hold the helicopter at a height. Push the
showly push the throtile stick up to make | rudder stick toward left to turn counter
helicopter fly higher.or release the stick a clockwise,and push the rudder stick toward
bit to make helicopter fly lower.Only small | right to turn clockwise.
amounts of stick position change are
required for smooth flying.
4 |
When you push up the right control lever__| When you push down the right control
(steering rudder),the nose incline to down, | lever(steering rudder),the nose incline to
the helicopter is moving to forward. up,the helicopter is moving to backward.
Note: If the helicopter rotates whilst in operation, please use
PUTO mag Ce Cella
If the helicopter spins during flight, follow the procedure below to stop the rotation.
Clockwi: i
cB )a( Tay Secersgreatn
Sore) knob
Helicopter rotates anticlockwise
Note: Adjust the knob as required until the rotation has stopped.
Counterclockwise
rotation vernier
adjustment knob
Helicopter rotates clockwise
Note: Adjust the knob as required until the rotation has stopped.OPERATION:
¥ Don’t operate the helicopter under the direct sun or strong lighting;it will affect the
control system of your helicopter.
% Don’t cover the lens of the transmitter.No signal will be released while you cover the lens.
¥ Don’t stick any other label onto the helicoptersthe other label will affect receiving of IR
signal
% The product uses light-minded materials, it will easy to damage if operate incorrectly,
tumble or bump or another factor will shatter the product.
Motor heating components, don't touch, avoid scald
ENVIRONMENT FOR FLIGHT:
L.Indoor environment with calm air condition. Beware of the air cirrulation from the
air-conditioner.
2.Space area:It is recommended to have to have space area over 20fi(W) X 30ft(L) x 10f(H).
3 Safety area:It is recommended that there is no electric fan,air-conditioner,reading lamp
or other dangerous objects to flying.
SPARE PARTS LIST
Order by item number from local distributors.
e
on S oo
S107G-02 $107G-03 S$107G-04 S10" IS
Head cover Main blade Tail decoration Connect buckle Balance bar
$107G-06 $107G-07 $107G-08 S107G-09 $107G-10
‘Tail lade Helicopter corpus Ascend and Descend Gear ‘Tail support pipe
SIG: SINGH SINICA SIGd
Main frame metal part A Main frame metal partB = Main shaft Chopper tail unit module
S107G-16 $107G-17 S107G-18 S$107G-19
shaft pipe Motor A Motor B Circuit board 3.7V Li-Poly
4 FECES ORRESRREFADER. BDSCIE|, ERZE, SHRRATRER.
S1076%
PO ee
NO.S107G ee ‘ “yee
‘PSSAESA REGLees 2 ei
EERE
exsuana — =
CHARS
A. HRERE
veniat ‘BP USBREESASMUSBINO, RST
MUSPREGREZARAVREOL, ABSALOM; RS
BIK40Z500%, ASL BTC
act ean 3
- PELRABINE ON” +, SRETNSGAR
- REAR CRBS “ON” +, SREWERR.
- RET an LA HEE BACYFS.
- BEARERASNSR, BWR TVET
\ a FAB Ho
)i 2, DAFAWATEERAPHITE, BRB
CHEMI) ACI RARE RSE TIER ESBt te UA aera B
SEHRRIRER, MONE | KOOTKOARET ASS
RBRNOLE, BHHESRA. K | HHOTHOCBEARES IETS 4
RRR, BHRESO TR
Go BPBRT, HAWS ARH
Sowa (Baie) Olt, BA GRANT (BONE) APE. Br
WERAT. SHANI. WO. SH MeeS
MIDVRAGHSOR ET, SEHADALL PTS, SHIOLBEIK
FRELRLVMERE, SNEABPEM IRL.
IRBs St hees
PRS ETHERS
» eanI FBRANSABR. Ea MKS |S
2 DS. BWSR B20 R (FR) X30 R CBR) X 10R C
32205. SOBRE RARA, SAR. SECRMSRMASHIW RE
ki Re
Se 1)
MIETREZURH, BHSSPRE, RUSERB+, TS
BSHNKRSRSRH.
S$107G-01 S$107G-02 S107G-03 S107G-05
oA AR wea EG
—~ | | tee) | ee
$107G-07 $107G-08 $107G-09 S107G-10
ER BBR ee exe
S107G-11 SL07G-12 S107G-13 S107G-14
SERA =RMAB = ee
S$107G-15 S107G-16 S107G-17 $107G-18 S107G-19
£ne ERMA ERB SBR ROVBRF BL
g
& FECEOO