Professional Documents
Culture Documents
Weekly Exam 1: Thursday, October 20, 2022 1:30 PM
Weekly Exam 1: Thursday, October 20, 2022 1:30 PM
WEEKLY EXAM 1
2. Find the torsional deflection, in degrees per foot length, of a steel shaft
1.75 inches in diameter which transmits 40 Hp at 1800 rpm. Assume a
modulus of rigidity of 12 x 106 psi.
a) 0.0871 b) 0.00871 c) 0.871 d) 0.000871
I
12. A centrifugal pump discharges 3000 liters per minute at a
22. An archer aims his bow upwards and pulls the string of his
arrow with a force of 80N.The strings make an angle of 25
degrees with vertical. Find the tension in the string
A. 88 N
B. 44 N
C. 22 N
D. 33 N
28. A 25 g mass bullet was fired at the wall. The bullet’s speed
upon hitting the wall is 350 m/s. What is the average force
(in Newton) if the bullet penetrates 10 cm?
A. 14,543.2 N
B. 11,342.2 N
C. 10,543.3 N
D. 15,312.5 N
a. 0.705 in
b. 0.891 in
c. 0.809 in
a. 36 psi
b. 11.5 psi
c. 30 psi
d. 27 psi
10,000 psi
8,530 psi
9,450 psi
10409 psi
55,000 lb
72,000 lb
60,000 lb
72. A 114 km/s speed is projected vertically how long will it take
to go back to its initial position.
A. 6.45 hrs
B. 1.23 hrs
C. 7.23 hrs
D. 8.45 hrs
a) 61 850 lb b) 65 810 lb
c) 61 580 lb d) 60 185 lb
A. 0.22 B. 0.195
C. 0.28 D. 0.24
A. 1000 lbf
B. 2000 lbf
C. 3000 lbf
D. 4000 lbf
A. 1 ft/sec2
B. 2.17 ft/sec2
C. 4.35 ft/sec2
D. 9.81 ft/sec2
77. What can the maximum load be on the column, if the cross
sectional area is 144 ft2 and the compressive stress cannot
exceed 200 lb/ft2?
A. 20 kips
a) 0.33 b) 0.25
c) 0.38 d) 0.22
2.25
1.95
2.14
2.62
80. A round steel shaft transmits 373 watts at 1800 rpm. The
torsional deflection is not to exceed 1 deg in a length equal
to 20 diameters. Find the shaft diameter.
6.53 mm
8.72 mm
12.84 mm
18.16 mm
9 mm
A. 6.79
B. 8.29
C. 7.54
D. 3.77
84. A body of mass 50 kg is being hoisted by a winch, and the
tension in the cable is 600 N. What is the acceleration?
A. 4.23 m/s2
B. 5.23 m/s2
C. 3.23 m/s2
D. 2.19 m/s2
85. A steel shaft operates at 186 rad/s and must handle 2 kW of
power. The shearing stress is not to exceed 40 MN/m².
Calculate the minimum shaft diameter based on pure
torsion.
A. 9 mm
B. 11 mm
C. 13 mm
D. 15mm
87. A 2 ft in length, 2’’ x 4’’ column having a fixed and free end is to be
designed to prevent buckling. Determine the slenderness ratio of
the column
B. 24sqrt3
88. What can the maximum load be on the column, if the cross
sectional area is 144 ft2 and the compressive stress cannot
exceed 200 lb/ft2?
A. 20 kips
B. 22 kips
C. 28.8 kips
D. 30 kips
2.25
1.95
2.14
2.62
90. A round steel shaft transmits 373 watts at 1800 rpm. The
torsional deflection is not to exceed 1 deg in a length equal
to 20 diameters. Find the shaft diameter.
6.53 mm
8.72 mm
12.84 mm
18.16 mm