1 Deep groove ball bearings
Designs and variants
Single row deep groove ball bearings
Stainless steel deep groove ball bearings
Single row deep groove bal bearings with filing slots
Double row deep groove ball bearings
Capped bearings.
Greases for capped bearings
Bearings with a snap ring groove.
Bearings with a anged outer ring
SKF Explorer bearings
Quiet running bearings fer large electric generators.
Cages.
Matched bearings
Bearing data
(Dimension standards, tolerances, internal clearance,
permissible misalignment)
Loads
(Minimum toad. axial load carrying capacity, load carrying,
capacity of matched bearing pairs, equivalent dynamic
bearing load, equivalent static bearing lead)
Temperature limits
Permissible speed
Designation system
Product tables
1.4 Single row deep groove bal bearings,
1.2 [COS oilsealee bearing units
1.3 Single row deep groove ball bearings witha snap
ring groove
1.4 Stainless steel deep groove bal bearings
1.5 Single row deep groove bal bearings with fling
slots
1.6 Double row deep groove bal bearings
SKF
2a
2k
21
261
242
242
2h
247
247
208
208,
28
209
250
254
256
256
258
260
308,
310
316
328
334
Other deep groove ball bearings
Car rllers 931
Sensor bearing units 987
High temperature bearings 1005
Bearings with Solid Oi 1023
INSOCOAT bearings 1029
Hybrid bearings 1003
NoWear coated bearings 1059
Polymer ball bearings > skfcom/bearings
2391 Deep groove ball bearings
More information
General bearing knowledge.
Bearing selection process
Lubrication
Bearing interfaces.
Seat tolerances for
conditions
Selecting internal clearance
Sealing, mounting and
dismounting
ard
Mounting instructions for
SKF bearing maintenance
a
59
109
29
U8
182
193
Individual bearings > sif 70mm
SKF 2031 Deep groove ball bearings
Contact seals (designation sufixes RSH,
RSH2, RSI RS1/VP311 or RS2)
+ aremade of sheet steel reinforced
= NBR
= FAI (designation suffix RS2 or RSH2,
available on request)
= food compatible, blue-coloured NBR*
(designation suffixVP311 and for stain-
less steel bearings only)
+ are available indifferent designs depend-
ing on the bearing they are used with
(tig. 20}
~ for 60, 62 ane 63 series bearings in two
SH designs (a,b), depending on the
~ for RSA designs, with sealing ether
against the inner ring shoulder (e) or
againsta recess in the inner ring side
{ace for chromium steel bearings (d) or
for stainless steel bearings (e), the rele~
vant design is determined by dimension
dor dzin the product table.
COS cil seated bearing units
«+ are typically used for applications with
sealing requirements exceeding the cap-
ablites of standard sealing solutions, ie
cilretention
hhave the following features compared to
bearings with external sealing solutions:
= need less axial space
= simplify mounting
~ avoid expensive machining ofthe shaft
because the inner ring shoulder s the
seal counterface
‘Thennateral FDA and ECapproved FDA
appreval is based an compliance with C=R 21
Section 177 2600 Rubber artcles mente for
peated use for se inconactwith eueous
{F¢ fatty foods. EC approvals based on compli
{ce withthe overall migration requirements of
{he German BR recomenndat.on XI for ek
gory materia
+ consis ofa 62 series deep groove ball
bearing and an SKF WAVE seal fg. 11:
~ single lip, spring loaded radial shaft seal
~ made of NBR
+ have limiting speeds quoted in the product
table that are based on the permissible
Circumferential speed fr the seal (14 ms}
Greases for capped bearings
Bearings capped on both sides ae lubricated
forthe ie of the bearing and are virtually
maintenance-free,
They are file with one afte fllowing
greases:
Single row bearings
«+ standard bearings (table 2)
On request, bearings can be supplied with
the following special greases:
+ high temperature grease GIN
+ wide temperature range grease HT or WT
+ wide temperature range and low-noise
grease LHT23
+ low temperature grease LT
Stainless steel bearings
+ wide temperature range and low-noise
grease LHT23 as standard
+ GF food-grade grease, registered by NSF
as category Hi (designation sux VP311)
The NSF registration confirms the
grease fulfils the requirements listed in the
US Food and Orug Administrations quide-
lines under 21 CFR section 178.3570
(lubricant acceptable with incidental food
contact for use in ané around food pro-
cessing areas),
«+ avaliable on request: special non-toxic
grease, registered by NSF as category Hi
(designation sutieVT378)
Bearings with filing slots
+ high temperature grease GIN
(On request, bearings can be supplied with
the following special greases:
+ wide temperature range grease HT or WT
+ wide temperature range and low-noise
‘grease LHT23
+ low vemperature grease LT
‘The technical specications of the various
‘greases are ited in table 3
‘The standard grease isnot identified in
the bearing designation (no designation suf-
fix, Special greases are indicated by the cor
responding grease suffix. Check availabilty
‘of bearings with special rease prior to
ordering
Ss
Seals made of FKM (fluoro rubber)
‘exposed to an open fame or termpera~
tures above 300 °C (570 ‘F) are aheatth
‘and environmental hazard! They remain
‘dangerous even afte they have cooled.
Read and follow the safety precau-
tions on page 197.
Fig. 10 fig.
Contact seals {€0S ol sealed bearing uit
a b « ‘ 4 K &
RSH RSH Rs Rs rsa
Ds2mm —D>25mm
2b SKF