Concept of IBS
Why IB coverage is important?Concept of In-Building Solutions
Hi-speed wireless connectivity in workplace, airports, hotels, convention.
centers, hospitals ete is becoming more prevalent. It provides today’s
business executives equipped with laptops, wireless LAN, mobile sets with
seamless wireless email and Internet service. The macro coverage from out
door site is not sufficient to meet this ever-growing demand, and there will
be multi cell issue (see the picture) so deploy a robust in-building wireless
solution for creating a competitive niche and better user experience...
. For example, a building may not receive adequate
mobile coverage from outdoor cell sites. This is
because in most cases the signals present outside
the building are unable to penetrate the building
material, thus resulting in poor coverage. A typical
problem in high rises is the problem of interference.
Crowded areas like malls, airports, large commercial
complexes need a dedicated system to handle the
capacity requirements for the large number of calls.
at such locations. Further with 3G quickly getting
popularity amongst these above mentioned
demographies, network strength, quality and aa frembemneekabone rs
capacity ete are becoming a cause of major concern :Why In-building Coverage is Important?
There are many reasons for the mobile operator for providing a dedicated IB
coverage
But mainly these are two
Technical Commercial
‘lack of coverage +Some countries more than 50% traffic
“Improvement of service quality from in building
*Need for more capacity «Indoor Solutions Can Make a Great
+Need for higher _ speed data rate Business Case
+Maximize the revenue of the operatorThe Indoor Planning Procedure
iT: ekeIBS Survey
For previding a good IB Solution first we have to do a proper surveyTools required
-Walk test tool(Net monitor, Nemo ,TEMS ete.)
*Measurement tape
*Still Camera
“G.P.SImportant pages in net monitor
Display 1~ Serving call info
* aeessenastes
arrsetsestet
/2.—More into about serving cellDisplay 4.&5-3"to 8" neighbour ceil
eres
fae
toranenteneG.P.S
The Global Positioning System (GPS) is a space-based |
navigation satellite system (GNSS) that provides reliable location and
time information in all weather and at all times and anywhere on or
near the Earth when and where there is an unobstructed line of sight to
four or more GPS satellites.Camera
Camera is using to take the pictures of
BTS location, Microwave pole location,
Shafts and Line of Site ete.The use of this in In Building survey are to measure the BTS location
-Microwave pole length. Distance between earth point to Equipment room
IF cable length etc..Check the BCCH ,RXL,RX@Q,CID of the all cells which are present in the building
Collect thi to card design of the Bui
Check the BTS& Microwave pole location
Check the cable shaft for running the Back bone cable
Take the Photographs of Building
‘Take the Photographs of BTS ,cable shaft and microwave pole location
ee eee mies
Check the Earth point
Measure the Earth cable length
Measure the power cable length
Measure the IF cable length
Take the contact details of the building contact person==
IBS DesignDesign Criteria
se
*Coverage planning
* Antenna marking on floor plan
*Make trunking Diagram
*Caleulate The EIRP of each
antenna
«Calculate the BOM
«The ideal distance between two
antenna is 20m
+All passive materials like
spliter,coupler,cable antenna are
should be support from 850 MHz
to 2500 MHz band
Tool used for IBS Design - IB
‘Wave
“Capacity planning
*Calculate the expected foot fall in
side building
*Calculate the total erlang
required
*As per erlang calculation
calculate the number of TRX
“Then plan the number of sector
+Normal commercial building per
subscriber erlang is 20ME
sHigh capacity site like Airport per
subscriber erlang is 33ME
In Sector planning try to avoid
multi sectors in single floorAntenna marking on floor plan 7
Indoor coverage radius and area vs.
‘design level from Omni antenna
To provide ‘full coverage’, antennas need to be placed with a certain coverage over lapPlacing the Indoor Antennas
-Place the hot-spot antennas and maximize data performance.
In this case of a shopping mall, the hot-spots for data and voice are typically the
food court, internet cafes and sitting areas
*Place the ‘cost-cutting’ antennas.
After the hot-spot antennas are placed you must place
all the antennas that will maximize the coverage per antenna
«Isolate the building.
Proper planning of an antenna at the entrance area and hand over zones
will isolate the building from even very close out door sites.
«Fill in the gaps.
The last placement of antennas will be ‘filling the gaps’ between the
anterinas just placed This will help to provide maximum coverageTrunking Diagram
tam.
14m om
‘3SPaR007 =
om
2sparony
asParoo4Link Budget
[reas Aa | aa as aS Be] AS] Ato.
(Canta tengih 72m) on 7 Tal 19}
[17]
70 iat — ia}
‘otal Cable Length 72" (np za za
Total Cable: loss 1/2" (dB) Zsa =275| = 07]
[cable length 779" (on) 0-06 70} 7o| 7)
33] es] ea]
EE]
|Fauai Cable Length 778" ima) iz
7732] 7 33]
joss_(d) (0.50) oi
Total Jumper toss (G8) a
Eabie length 15/8 —(m)
Total Cable Lengih 1 38" (ay ala
Total Cable loss 1 3/6" (dB) | ‘all
FFotal Cable loss (di) 36] Sr] |
oupier 6 dB(Coupling) 4
[Coupieréaescthru, =I]
[Coupier 10 ebiCoupiin =10}
Coupler 10 se(rneop as
‘Dupler 15 g6(Coupina) =18] t
Coupler 15 asim a3 T I
[Total Coupier Loss 7 Se] ota]
Spitters 2 way | a] a] 3
Splitter 3 3 ya
Splitter 4 way = 7]
‘otal Splitter Loss. =i8| za] =a
[STS euiput power GB) 45] 46| a6]
tens Gain (dBi) al at __al
hienha EIRP{IBM)
eer IrBill of material
PASSIVE BOM
Project name: |AVAN| RIVER SIDE MALL
Project creation date: 32/28/2020 Designer: Tyco RF Planning Team
Designcompany: Tyco Elactronies
Antenna landrew
[CELUMAN-O-25 [Omnidirectional Source-Sullding Antenna
ees
Antenne landrew
ELMAND-25 [Direcuonal Source Building Antenna
la
Cable landrew
LOFe-soA [SO ohms 1/2" comsial cable foam
7/8” Air Dielectric, Hi Series ~S0-ohin
Ina.
Connector landese LaPNM In for LOF4-SCA Low Densit wa
[Dietectric Cable L
Connector fandrewe Sent li Mele Connector for HISRP-S0 Air Iwa
Dielectric cable
Spirter landrew CISCPUSN [Directional Coupler / Unequal Splitter (G7 [N/A
[dB / 10:d8)~ 800-2500 Mliz~ Connectors
Splitter lalenDick SPL-FOB25-2¢_|2 Woy Covity Poner Splitter ay
Splitter
lalanDick
SPLFORDS-3C Power!
[3 way Cavit
la
UMTS PON3:1) 3
Gsm isooPoKet) (ADC 3]
‘GSM 900 POH(S:1) 2
(COMA POI 233Indoor Radio planning tool
IB Wave _ The most popular in door RF planning tool
iBwave Solutions is a telecom radio planning software provider that develops
solutions for the in-building wireless industry. iBwave is best known for its
software iBwave Design, mostly used by telecom operators, system integrators
and equipment vendors. iBwave is a Canadian-based company that was
founded in 2003 and is headquartered in Montreal.
A privately-held company, iBwave focuses on integrated solutions to automate
and standardize the design of wireless communications inside buildings and
infrastructures.
In 2010,
S iBwaveTraffic dimensioning
Erlang __The Traffic Measurement
An Erlang is a unit of telecommunications traffic measurement,
One Erlang is the continuous use of one voice channel, In call minutes, one Erlang is 60 min/h,
1440 call min/24 h. In practice, when doing mobile capacity calculations, an Erlang is used to
describe the total traffic volume of 1h, for a specific cell,
Call Blocking, Grade of Service
‘The blocking rate (grade of service or GOS) is defined as the percentage of calls that
are rejected due to lack of channels. If the users makes 100 calls, and one call is rejected
due to lack of channels (capacity) the blocking rate is 1 in 100, or 1%. This is referred to
as 1% GOS, Operators might differentiate the GOS target for different indoor solutions,
with a strict GOS of 0.5% in an office building but allowing a GOS of 2% in shopping
The Erlang B Table
Provided that the-calls are Erlang-distributed, you can use the Erlang B formula to calculate
the required number of channels ata given load rate, and a given grade of service.Erlang Example
Ifa group of 20 users makes 60 calls in 1 h, and each call had an average
duration of 3 min,
then we can calculate the traffic in Erlangs:
total minutes of traffic in 1 h = duration < number of calls
total minutes of traffic in 1 h= 3 x 60
total minutes of traffic in 1 h = 180 min
The Erlangs are defined as traffic (minutes) per hour:
Erlangs = 180/60 = 3E
Knowing the number of users (20), we can calculate the load per user:
user load = total load/ number of users
user load = 3/20 = 0.150 E = 150mE per user
Then, if we have the same type of users inside a building with 350 mobile
users, we can calculate what capacity we need:
total load = number of users = load per user
total load = 350 x 150mE= 52.5ETypical user load in Erlang
User type Traffic load per user
Extreme user : 200 mE
Heavy user :100 mE
Normal office user :5O mE
Private user :20 mESpecial design considerations
Most of the design methods and considerations are the same for all building. But the below mentioned
are some of the points we need to address, in addition to all the standard RF considerations.
+ Make sure you prepare for more capacity or sectors for future upgrades.
+ Make sure yoti cover the executive floor 100%.
+ Is there a need for elevator coverage?
* Are there special installation challenges (e.g. fire proofing)?
+ Pay attention to the service rooms or areas (e.g. IT server rooms).
+ Are there special EMR concerns (like in a hospitalj?
+ What type of services might be needed in the future ~ 3G, 3,5G?
+ Are there any hot-spots in the building that need special attention?Handover Considerations Inside Buildings
The indoor DAS system implemented in the building should be prepared
for future traffic growth.
The best way to prepare this is to have a sector plan for future
sectorization of the system.
Even if the system is implemented as one sector, you need to look ahead,
especially for UMTS, in order to prepare for more sectors.
Well-defined HO zones are important for GSM and UMTS/HSDPA to avoid
‘ping-pong’ HO on GSM, extensive soft HO zones on UMTS and degraded
HSPA performance.
As a general rule you must try to avoid having the handover zones in large
open areas inside the building. Here it can be difficult to design and
control the handover zone
Try to advantage of the natural isolation provided by the building to
separate the different sectors or cells.eg. Floor separationThe typical GSM handover scenario in a buildingCoax Cable
coax cable is widely used in all types of distributed antenna
Materials For IBS
systems, especially in passive systems.
. Typical losses for the commonly used types of passive coaxial
Cables are mentioned Below
Typical Attenuation of Coaxial Cable
Freequency/Typical Loss per 100m(dBm]
Cable type _[900MHZ 1800MEH 2100MHZ
1/4 inch 13} 19 20
1/2 inch 10
2/8 inch
1 1/4 inch
15/8 inch
44
37 3.3]RF connector
coaxial RF connector is an electrical connector designed to work at radio frequencies
in the multi-megahertz range. RF connectors are typically used with coaxial cables and
are designed te maintain the shielding that the coaxial design offers. Better models also
minimize the change in transmission line impedance at the connection. Mechanically
they provide a fastening mechanism (thread, bayonet, braces, push pull) and springs
for a low holmic electric contact while sparing the gold surface thus allowing above
1000 reconnects and reducing the insertion force. Research activity in the area of radio-
frequency (RF) circuit design has surged in the last decade in direct response to the
enormous market demand for inexpensive, high data rate wireless transceivers’ .N and
DIN type connectors are commonly used in IBS
Gus
BSuy
,L29(7/16)
Q
Gg
NAntenna
Anantenna gives the wireless system three fundamental properties: gain, direction
and polarization. Gain is a measure of increase in power. Gain is the amount of
increase in energy that an antenna adds to a radio frequency (RF) signal. Direction is
the shape of the transmission pattern. As the gain of a directional antenna increases,
the angle of radiation usually decreases. This provides a greater coverage distance,
but with a reduced coverage angle. The coverage area or radiation pattern is
measured in degrees. These angles are measured in degrees and are called beam
widths,
Omni Antenna panel AntennaSplitters
Splitters and power dividers are the most commonly used passive components in
distributed antenna systems. Splitters are used for splitting one coax line into two or more lines,
and vice versa. If splitting to two ports, only half-power minus the insertion loss, typically about
0.1 4B, is available at the two ports. It is very important to terminate all ports on the splitter;
do not leave one port open. Ifit is unused, terminate it with a dummy load.
You can calculate the loss through the splitter:
splitter loss =10 log (number of ports}+ insertion loss
For a 1:3 splitter ,the attenuation will be:
10 log(3)+0.1dB+4.87dB
2Way splitter 4Way splitter 3Way splitterTapers are used like splitters, used to divide the signal/power from one into
two lines. The difference from the standard 1:2 splitter is that the power is
not equally divided among the ports.
In put &
Couple port
Typical Taps and their coupling loss
Through
port
Tt Coupling port loss Throu: ort loss
S.dB 5 2
6 dB 6 LS
10dB 10 1
15dB is 0.5
20dB 20 0.2Attenuators
Attenuators attenuate the signal with the value of the
attenuator.
Attenuators are used to bring higher power signals down to a desired range
of operation
The different ranges are 10dB,20dB,30 dB 40dB & variable attenuatorDummy Loads or Terminators
Terminators are used as matching loads on the transmission lines,
often on one port of a circulator, or any ‘open’ or unused ports on other
components.
e:
50W 10W3 dB Coupler (90 Hybrid)
The 3 dB coupler are mostly used for combining signals from two
signal sources. At the same time the coupler will split the two combined
signals into two output ports.
At the time of using this product two things are very important
+Power handling capacity of each port
‘Isolation between 2 portsHybrid Combiner
Hybrid combiner mostly used for combining signals from two different
signal sources
The insertion loss is 3 dBIBS ImplementationFor crea‘ a good IBS site the implementation quality have a jor roll
‘Use trained and skilled manpower for Installations
*Antennas should be fixed as per the design.
+All the splitters couplers are fixed properly and easy to maintain
*All connectors should be tight
*Make sure cable and jumpers are not bend sharply and
no physical damage
*All junctions should be covered with weather proof
+Use proper tools for implementation
‘The VSWR should be <1.3
+Use 3 pin top with proper power rating power cable for any type of
electrical power taping
All power and earth connections should be tight
*Prepare and submit the proper AS Built report to the operatorTools Required
iT
Drilling Machine +Hack saw *Sleaving tool
“
‘Screw driver set +Cutting player
KnifeIBS Quality TestThe most important thing in the IBS is the quality test ,because
for getting a quality network we have to check the quality of all
part of the IBS
Check the product quality
«Is all the products are in ETSI Standard
“The VSWR is with in the threshold
“The performance is as per the specifications
Implementation Quality
All the connectors should be tight
There is no sharp bending in RF cable
All the junctions are protected from moisture
The VSWR should be <1.3
Network Quality
Do the walk test
Check all the parameters are ok(DLRXL,DLRXQ,UL Level
ULRXQ,SQ, Short call ,Long call ,Cell selection and
reselection, Hand over,& no co and adjacent channel interference }==
IBSO&M*The O&M Team /Engineer should have the as built design of the site
*He have a good knowledge in passive and active components
«The team have proper tools
-Walk test tool(Nemo or TEMS)
Tool kit (installation tools)
*Site master/spectrum analyzersModel O & M Check list
16504 M CHECK LST
mio q = porModel O & M Check list
BE ANTINNAS
“isl he dee a a
Tie cesusiectbe dened eg
ely ema een iar
SF FIRDER CABLE
Thee enna shana
Thame tncorr shade retorts
Thre shel net an amass ible oath aes
‘Thacalsshelbe meted prope ih ered bed dees
Thao sed te pred meh orc lpi eee
‘heap cs h toiboet
aap pc cet encircle
Thea dal bebe
HLECTRICALModel O & M Check list
The pce Se dbp ea ea
The peceshlte rtd ppt a bs
an FenasModel O & M Check list
Few efoto ate
Feet
Fes
INRACELL RDO
Site Saed abode AB
Secor shod ePaper
Sere iheat} sede Pope
Sects shdthe ape
Sect Secer} shade ope
Serr Sioour? shade ope
INERCELL ANDOU
Sect |wNegbagcal shade pe
Seco Neiteoag co htop
Sec acing shad geTHANK YOU