Professional Documents
Culture Documents
CED229/51/55/98
TABLE OF CONTENTS
Location of PCBS……… …………………1-1 Servo board-circuit diagram-2……………6-2
Specifications……… …………… …………1-2 Layout diagram top/bottom view…………6-3
Safety Instruction, Warning & Notes ..….1-3 SB+CB board-circuit diagram… …….……7-1
Disassembly diagram……… … …….…..2-1/2 SB+CB board-layout top/bottom vie w.......7-2
Software version check&upgrade….……3-1 LB+SD+CB board-circuit diagram.....……8-1
Malfunction check chart…… ……… … . . . 3-2 LB+SD+CB board-layout diagram............8-2
Wiring diagram… ………… ………………4-1 KEY board-circuit diagram…… …. . . ………9-1
Main board-circuit diagram-1……………5-1 KEY board layout diagram ....................… .……9-2
Main board-circuit diagram-2……………5-2 Exploded view-main unit ........................... 10-1
PCB layout top/bottom view ……………5-3
Servo board-circuit diagram-1 ……….…6-1
CLASS 1
©
Copyright 2011 Philips Consumer Electronics B.V. Eindhoven, The Netherlands LASER PRODUCT
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without
the prior permission of Philips.
Published by DB- SL 1149 BG AVM Printed in The Netherlands Subject to modification 3141 785 35593
Version 1.3
X/78 /51 /98
SPECIFICATIONS
General Tuner
Power supply: 12V DC(11V-16V ) Frequency range 87.5-108.0MHz(Eur)
negative ground -FM 65.0-74. 0MHz(OIRT)
Fuse: 15A 87.5-107.9MHz(Ame)
Suitable speaker impedance: 4-8Ω Frequency range 522-1620KHz(Eur)
Maximum power output: 45Wx4channels -AM(MW) 530-1710MHz(Ame)
Continuous power output: 18Wx4channels(4Ω 10% T. H.D.) Usable sensitivity 8uV
Pre-Amp output voltage: 2.0V(CD play mode;1kHz,0dB, -FM
10KΩ load) Usable sensitivity 30uV
Aux-in level: ≥500mV -AM(MW)(S/N=20dB)
Dimensions(WxHxD): 188x58x193mm Frequency response 30Hz-15KHz
Weight: 1.9kg Stereo separation 30db(1KHz)
Signal/noise ratio >55dB
Disc Player
System: Disc digital audio system
Frequency response: 20Hz-20k Hz
Signal/noise ratio: >75dB
Total harmonic distortion: Less than 0. 3%(1KHz)
Channel separation: >55dB
Video signal for mat: NTSC/PAL/AUTO
Video output: 1+/0.2V
LCD
Notes:
• Figures can deviate due to the different set executions.
• Specifications are indicative (subject to change).
It should be noted that on the European Service website, 0/6/12 SCART switch control signal on A/V
“Alternative BOM” is referred to as “Design variant”. board. 0 = loop through (AUX to TV),
6 = play 16 : 9 format, 12 = play 4 : 3
The third digit in the serial number (example: format
KX 2B0835000001) indicates the number of the alternative 2DNR Spatial (2D) Noise Reduction
B.O.M. (Bill Of Materials) that has been used for producing the 3DNR Temporal (3D) Noise Reduction
specific AV set. In general, it is possible that the same AV AARA Automatic Aspect Ratio Adaptation:
model on the market is produced with e.g. two different types algorithm that adapts aspect ratio to
of display, coming from two different suppliers. This remove horizontal black bars; keeps
will then result in sets which have the same CTN (Commercial the original aspect ratio
Type Number; e.g. MCM394/12) but which have a different ACI Automatic Channel Installation:
B.O.M. number. algorithm that installs TV channels
directly from a cable network by
Also, it is possible that same model on the market is produced means of a predefined TXT page
with two production centers, however their partslist is the same. ADC Analogue to Digital Converter
In such case, no alternative B.O.M. will be created. AFC Automatic Frequency Control: control
signal used to tune to the correct
By looking at the third digit of the serial number, one can frequency
identify which B.O.M. is used for the set he is working with. AGC Automatic Gain Control: algorithm that
If the third digit of the serial number contains the number “1” controls the video input of the feature
(example: KX 1B033500001), then the set has been box
manufactured according to B.O.M. number 1. If the third digit is AM Amplitude Modulation
a “2” (example: KX 2B0335000001), then the set has been ANR Automatic Noise Reduction: one of the
produced according to B.O.M. no. 2. This is important for algorithms of Auto TV
ordering the correct spare parts! AP Asia Pacific
For the third digit, the numbers 1...9 and the characters A...Z AR Aspect Ratio: 4 by 3 or 16 by 9
can be used, so in total: 9 plus 26= 35 different B.O.M.s can be ASF Auto Screen Fit: algorithm that adapts
indicated by the third digit of the serial number. aspect ratio to remove horizontal black
bars without discarding video
Identification: The bottom line of a type plate gives a 14-digit information
serial number. Digits 1 and 2 refer to the production centre (e.g. ATSC Advanced Television Systems
LM is Arts), digit 3 refers to the B.O.M. code, digit 4 refers Committee, the digital TV standard in
to the Service version change code, digits 5 and 6 refer to the the USA
production year, and digits 7 and 8 refer to production week (in ATV See Auto TV
example below it is 2008 week 50). The 6 last digits contain the Auto TV A hardware and software control
serial number. system that measures picture content,
and adapts image parameters in a
Model FWM572/12 dynamic way
220-230 50Hz 60W AV External Audio Video
AVC Audio Video Controller
AVIP Audio Video Input Processor
FWM572/12 B/G Monochrome TV system. Sound
carrier distance is 5.5 MHz
LM1A0850005644 BLR Board-Level Repair
BTSC Broadcast Television Standard
Committee. Multiplex FM stereo sound
Figure 2-1 Serial number (example) system, originating from the USA and
used e.g. in LATAM and AP-NTSC
2.3.6 Module Level Repair (MLR) or Component Level Repair countries
(CLR) B-TXT Blue TeleteXT
C Centre channel (audio)
If a board is defective, consult your repair procedure to decide CEC Consumer Electronics Control bus:
if the board has to be exchanged or if it should be repaired on remote control bus on HDMI
component level. connections
If your repair procedure says the board should be exchanged CL Constant Level: audio output to
completely, do not solder on the defective board. Otherwise, it connect with an external amplifier
cannot be returned to the O.E.M. supplier for back charging! CLR Component Level Repair
COLUMBUS COlor LUMinance Baseband
2.3.7 Practical Service Precautions Universal Sub-system
ComPair Computer aided rePair
CP Connected Planet / Copy Protection
• It makes sense to avoid exposure to electrical shock.
CSM Customer Service Mode
While some sources are expected to have a possible
CTI Color Transient Improvement:
dangerous impact, others of quite high potential are of
manipulates steepness of chroma
limited current and are sometimes held in less regard.
transients
• Always respect voltages. While some may not be
CVBS Composite Video Blanking and
dangerous in themselves, they can cause unexpected
Synchronization
reactions that are best avoided. Before reaching into a
DAC Digital to Analogue Converter
powered TV set, it is best to test the high voltage insulation.
DBE Dynamic Bass Enhancement: extra
It is easy to do, and is a good service precaution.
low frequency amplification
DDC See “E-DDC”
1 -7
D/K Monochrome TV system. Sound lines. The fields are written in “pairs”,
carrier distance is 6.5 MHz causing line flicker.
DFI Dynamic Frame Insertion IR Infra Red
DFU Directions For Use: owner's manual IRQ Interrupt Request
DMR Digital Media Reader: card reader ITU-656 The ITU Radio communication Sector
DMSD Digital Multi Standard Decoding (ITU-R) is a standards body
DNM Digital Natural Motion subcommittee of the International
DNR Digital Noise Reduction: noise Telecommunication Union relating to
reduction feature of the set radio communication. ITU-656 (a.k.a.
DRAM Dynamic RAM SDI), is a digitized video format used
DRM Digital Rights Management for broadcast grade video.
DSP Digital Signal Processing Uncompressed digital component or
DST Dealer Service Tool: special remote digital composite signals can be used.
control designed for service The SDI signal is self-synchronizing,
technicians uses 8 bit or 10 bit data words, and has
DTCP Digital Transmission Content a maximum data rate of 270 Mbit/s,
Protection; A protocol for protecting with a minimum bandwidth of 135
digital audio/video content that is MHz.
traversing a high speed serial bus, ITV Institutional TeleVision; TV sets for
such as IEEE-1394 hotels, hospitals etc.
DVB-C Digital Video Broadcast - Cable JOP Jaguar Output Processor
DVB-T Digital Video Broadcast - Terrestrial LS Last Status; The settings last chosen
DVD Digital Versatile Disc by the customer and read and stored
DVI(-d) Digital Visual Interface (d= digital only) in RAM or in the NVM. They are called
E-DDC Enhanced Display Data Channel at start-up of the set to configure it
(VESA standard for communication according to the customer's
channel and display). Using E-DDC, preferences
the video source can read the EDID LATAM Latin America
information form the display. LCD Liquid Crystal Display
EDID Extended Display Identification Data LED Light Emitting Diode
(VESA standard) L/L' Monochrome TV system. Sound
EEPROM Electrically Erasable and carrier distance is 6.5 MHz. L' is Band
Programmable Read Only Memory I, L is all bands except for Band I
EMI Electro Magnetic Interference LORE LOcal REgression approximation
EPLD Erasable Programmable Logic Device noise reduction
EU Europe LPL LG.Philips LCD (supplier)
EXT EXTernal (source), entering the set by LS Loudspeaker
SCART or by cinches (jacks) LVDS Low Voltage Differential Signalling
FBL Fast BLanking: DC signal Mbps Mega bits per second
accompanying RGB signals M/N Monochrome TV system. Sound
FDS Full Dual Screen (same as FDW) carrier distance is 4.5 MHz
FDW Full Dual Window (same as FDS) MIPS Microprocessor without Interlocked
FLASH FLASH memory Pipeline-Stages; A RISC-based
FM Field Memory or Frequency microprocessor
Modulation MOP Matrix Output Processor
FPGA Field-Programmable Gate Array MOSFET Metal Oxide Silicon Field Effect
FTV Flat TeleVision Transistor, switching device
Gb/s Giga bits per second MPEG Motion Pictures Experts Group
G-TXT Green TeleteXT MPIF Multi Platform InterFace
H H_sync to the module MUTE MUTE Line
HD High Definition NC Not Connected
HDD Hard Disk Drive NICAM Near Instantaneous Compounded
HDCP High-bandwidth Digital Content Audio Multiplexing. This is a digital
Protection: A “key” encoded into the sound system, mainly used in Europe.
HDMI/DVI signal that prevents video NTC Negative Temperature Coefficient,
data piracy. If a source is HDCP coded non-linear resistor
and connected via HDMI/DVI without NTSC National Television Standard
the proper HDCP decoding, the Committee. Color system mainly used
picture is put into a “snow vision” mode in North America and Japan. Color
or changed to a low resolution. For carrier NTSC M/N= 3.579545 MHz,
normal content distribution the source NTSC 4.43= 4.433619 MHz (this is a
and the display device must be VCR norm, it is not transmitted off-air)
enabled for HDCP “software key” NVM Non-Volatile Memory: IC containing
decoding. TV related data such as alignments
HDMI High Definition Multimedia Interface O/C Open Circuit
HP HeadPhone OSD On Screen Display
I Monochrome TV system. Sound OTC On screen display Teletext and
carrier distance is 6.0 MHz Control; also called Artistic (SAA5800)
I2C Inter IC bus P50 Project 50: communication protocol
I2 D Inter IC Data bus between TV and peripherals
I2 S Inter IC Sound bus PAL Phase Alternating Line. Color system
IF Intermediate Frequency mainly used in West Europe (color
Interlaced Scan mode where two fields are used carrier= 4.433619 MHz) and South
to form one frame. Each field contains America (color carrier PAL M=
half the number of the total amount of
1-8
Safety Instructions, Warnings, Notes, and Abbreviation List
Disassembly Diagram
11、loosen and take out the bolt 12、loosen and take out the bolt 13、loosen and take out the bolt
with a screw-driver, with a screw-driver, with a screw-driver,
14、P ull out the two pieces of connection-pegs 15、Loosen and take out the six bolts
carefully with a screwdriver.
3-1 3-1
Check MCU software version When the device is power on at the first time, in USB/SD/Disc mode,
press the key in turn:
1. Copy the file "MCU.BIN" into USB stick stop up down left right
2. Power on the device, and plug the USB stick into USB socket. The LCD will display the servo software, MCU, TFT version number.
After the device read the content in the USB, the LCD will show
a upgrade menu, and enter into the upgrading status.
3. The LCD will appear a number (changed from 20 to 0), and when
arrived the number 0, then appear a processing bar, which mean
the device enters upgrading status.
4. In step 3. if want to enter into upgrading status quickly, press the
key OKto confirm, the processing bar will appear immediately.
5. Disconnect the USB stick.
6. When software upgrade complete, the device will power off automatically.
1. Copy the file "ROM.BIN" into USB stick (note to delete the file "MCU.BIN" ).
2. Power on the device, and plug the USB stick into USB socket. After the
device read the content in the USB, the LCD will show a upgrade menu,
and enter into the upgrading status.
3. The LCD will appear a number(changed from 20 to 0), and when arrived
the number 0, then appear a processing bar, which mean the device enters
upgrading status.
4. Press the key OK to confirm, the processing bar will appear immediately.
5. Disconnect the USB stick.
6. When software upgrade complete, the device will change to disc mode automatically.
3-2 3-2
NO NO NO
NO NO NO
TDA7388 of main
NO NO Change main NO
Main board which in
Main board
WIRING DIAGRAM
5-1 5-1