Professional Documents
Culture Documents
Feature Default Parameters 2.1 Firstly fasten the device to somewhere firm, then install
Configuration 4. Mode Selection 4.2 Repeater Mode
Router Wi-Fi signal output power 100%. the device in the holder. 2. Technically speaking, the product web UI will guide you This product has 4 modes. Click "Switch mode" to switch mode. 1. Click "switch Mode" and select Repeater Mode.
- Dual band with maximum speed up to 5G 867Mbps and 2.4G 300Mbps. Web: http://waplogin.link 2.4G SSID: WAVLINK-N_XXXX to the login page once you have connected to the device 2. After scanning, please make sure the Wi-Fi you want to select
- Weatherproof and build in lightning arrester withstand harsh outdoor conditions. Default IP: 192.168.30.1 5G/AC SSID: WAVLINK-AC_XXXX Better reception: signal 81%~100%. 1. Connection successfully in your first time, but if it doesn't, please manually is listed, and click "Next", if it isn't, please click "Rescan".
- Four 7dBi omnidirectional antennas eliminate Wi-Fi dead zones. Login Password: admin Wireless Password: open input 192.168.30.1 or waplogin.link in the address bar of your
Mesh 1.1 Via Wireless
- High power amplifier for stronger signal transmission. Extender Good reception: signal 60%~80%. browser on PC/laptop or phone, the default password is admin.
- Gigabit port provides faster connection.
- Passive PoE support for flexible deployment. LED Indicators Weak reception: signal below 0~59%.
English
LAN devices (smart phone, tablet computer, laptop, etc.) and connect
AC1200 Dual Band High-Power Outdoor Off The Ethernet port is disconnected. 2.2 Now please follow the steps below. to it.
Please set up this device first!
the AP mode manually.Click on "Next".
1. Please follow the installation steps when assembling the device.
Router/AP/Extender WAN/LAN On The Ethernet port is connected.
Please enter your password
2. Connect the WAN/LAN port of this product to the poe and connect
Backhaul the lan data in port of the poe box to the host router via Ethernet
Off The Ethernet port is disconnected. Login
cable. Then you can change the SSID or use the default one, the
Another router has not been connected
Fast flash when the device is the repeater mode. encryption mode recommend is WPA2-PSK. For your network
WAVLINK-N_XXXX 3. Select your Country/Region and Time Zone. For your network
The another router has been connected but the
security. please create a new password according to the rule.
WAVLINK-AC_XXXX security, we suggest that you set a new login password.
Status Slow flash device has no access to the network in the Then click on "Save" and wait for the setting process to complete.
repeater mode. WAVLINK-N_XXXX
WAVLINK-AC_XXXX
The device keeps on in the AP mode;
On The device can access the network normally.
www.wavlink.com/en_us/WING-12M Wi-Fi Signal 1) Connect the "PoE" port of PoE converter to the PoE IN(WAN)
1.2 Via Cable
port of the device.
Scan the QR code or load the link for
2) Connect "LAN DATA IN" to "LAN" of your router.
Quick Start Guide downloading 3) Plug in the device through the power adapter.
LAN LED Pass RJ45 cable through Spin 2.4G antenna into the
Wi-Fi signal output power 100%. the spiral cover 4) Push the "ON/OFF" button to turn on or off the device.
2.4G RP-SMA Antenna Connectors POWER LED 2.4G external RP-SMA connector
Pass RJ45 cable through Spin 5G antenna into the 5G Attention
5G RP-SMA Antenna Connectors Reset/PAIR Button Better reception: signal 81%~100%.
the rubber seal external RP-SMA connector 1) Ensure that you use a certified CAT5e/CAT6 Ethernet Connect Ethernet cable to your PC/laptop and device’s LAN
3 x Wi-Fi Signal LEDs LAN Backhaul Port Pass RJ45 cable through Note: The three colored bars in "Admin" area indicates the
Good reception: signal 60%~80%. Screw the holder cable with RJ45 connectors Backhaul port, then you can start configuring the device.
the holder strength of the login password.
Status LED WAN(PoE IN)/LAN Port Plug the rubber seal to the holder 2) Make sure the length of the Ethernet cable from PoE to
Grounding Terminal Weak reception: signal below 0~59%. Connect the RJ45 cable to Screw the spiral cover
WAN/LAN Backhaul LED the device is less than 60 meters (196 ft).
PoE IN/WAN port.
01 02 03 04 05 06 07 08
OFF/ON OFF/ON
for networking in Mesh Router mode, refer to 5 for adding method. 2. Select your Country/Region and Time Zone. Enter the Admin 1
Password. After click "start Pairing", follow 5 to add this device Q1. What can l do if l can not access the Internet?
on the primary router. - Make sure your Internet works normally, please contact your
ISP(Internet Service Provider) if it doesn't.
Wi-Fi Password Management - Initiate your browser, enter 192.168.30.1 or waplogin.link,
4. After scanning, please make sure the device you want to add then set up the following quick start guide.
is listed, and click “Add”.If not, make sure the Mesh extenter to When you need to change your Wi-Fi password, please 4. Click on to locate the firmware file. - Reboot your device and try it again.
be added is in a paired state. Click : “Rescan”. click on “Wireless”. 5. Click on "Upload" and choose "Apply", and wait for the Q2. Why can’t I visit the web UI by inputting the IP
firmware upgrade process to complete. address 192.168.30.1 or waplogin.link?
2. Set the wireless network encryption mode and password for this Option II - lf you can’t log in to the lP address or URL in AP Mode,
device. Click "Save". please check the lP address arranged by the upstream router,
1. Log in to 192.168.30.1 or waplogin.link, then choose
then try to restart the process.
"Advanced" and select "Firmware Update". - Make sure you have connected to the WiFi of the
Wavlink device.
WAVLINK-N_050E