Professional Documents
Culture Documents
XVS-G1 System
XVS-G1
XKS-G1110 XKS-G1600 XKS-G1700
XZS-G1500 XZS-G1610 XZS-G1620 XZS-G1750 XZS-G1770
XZS-G1800
ICP-X1116 ICP-X1124 ICP-X1216 ICP-X1224
3
Transition Type ......................................... 58 Overview .....................................................75
Setting a Transition Type ............................58 Setting a Chroma Key .................................75
Setting Super Mix........................................59 Chroma Key Adjustments ...........................75
Setting a Preset Color Mix ..........................59 Key Fill and Key Source ........................... 78
Transition Rate .......................................... 60 Selecting Signals .........................................78
Transition Rate Input/Display Mode...........60 Selecting SL Key Content ...........................80
Setting the Transition Rate ..........................60 Key Edges.................................................. 81
Executing a Transition.............................. 61 Setting Key Edges .......................................81
Auto Transitions ..........................................61 Setting Key Drop.........................................83
Manual Transitions (Fader Lever)...............61 Setting a Zabton...........................................84
Fader Lever Operation ................................62 Masks ......................................................... 85
Pattern Limit .............................................. 63 Setting a Mask .............................................85
Executing a Pattern Limit............................64 Processed Key .......................................... 86
Transition Preview .................................... 65 DME Effects for Keys .................................86
Setting Transition Preview ..........................65 Other Settings ........................................... 88
Executing Transition Preview .....................65 Blink ............................................................88
Independent Key Transitions................... 66 Video Process ..............................................88
Overview .....................................................66 Resizer ....................................................... 89
Basic Independent Key Transition Overview .....................................................89
Operations ..........................................67 Two-Dimensional Transforms on Keys ......89
Setting the Independent Key Transition Setting Rotation ...........................................90
Type ...................................................67 Removing the Virtual Image .......................90
Setting the Independent Key Transition Setting a Border...........................................91
Rate ....................................................68 Setting a Crop..............................................92
Executing an Independent Key Setting a CG Border ....................................92
Transition ...........................................69
Setting Interpolation Processing..................93
Fade-to-Black ............................................ 70
Setting Resizer Effects ................................94
Setting Fade-to-Black..................................70
Key Snapshots .......................................... 96
Executing Fade-to-Black.............................70
Key Snapshot Operations (Flexi Pad Control
Block).................................................96
Key Snapshot Operations (Menu) ...............96
Chapter 6 Keys
Overview .................................................... 71
Key Fill and Key Source .............................71 Chapter 7 Wipes
Key Type .....................................................71 Overview .................................................... 98
Key Modifiers .............................................72 Setting a Wipe ........................................... 99
Key Memory ...............................................72 Setting a Wipe Pattern.................................99
Resizer .........................................................72 Setting a Pattern Mix...................................99
SL Key.........................................................72 Setting Modifiers .......................................101
Key Type .................................................... 73 Setting an Independent Key Transition
Setting the Key Type...................................73 Wipe................................................... 108
Chroma Key ............................................... 75
4
Setting a Wipe Pattern for an Independent Key Frame Memory Operations..................... 128
Transition .........................................108 Assigning a Frame Memory Output ..........128
Setting Independent Key Transition Wipe Selecting an Input Signal...........................128
Modifiers..........................................108 Selecting a Frame Memory Output
Wipe Snapshots ...................................... 110 Channel ............................................128
Wipe Snapshot Operations (Flexi Pad Control Frame Memory Content Operations..........129
Block)...............................................110 Still Image Operations ............................ 131
Wipe Snapshot Operations (Menu) ...........111 Creating a Still Image (Freeze) .................131
Recalling a Still Image ..............................131
Video Operations .................................... 132
Creating Video (Record) ...........................132
Chapter 8 DME Wipes
Recalling Video.........................................133
Overview .................................................. 112 Playing Video ............................................133
Setting a DME Wipe ................................ 115
Setting a DME Wipe Pattern .....................115
Setting Modifiers.......................................116
Setting an Independent Key Transition Chapter 11 Clip Player
DME Wipe.......................................... 120 Overview .................................................. 136
Setting a DME Wipe Pattern for an Areas Used by Clip Player ........................136
Independent Key Transition.............120
Clip Player Outputs ...................................136
Setting Independent Key Transition DME
Clip Player Content ...................................136
Wipe Modifiers ................................120
Clip Player Operations............................ 137
DME Wipe Snapshots ............................. 122
Assigning Clip Player Outputs ..................137
DME Wipe Snapshot Operations (Flexi Pad
Control Block) .................................122 Selecting a Clip Player Output Channel....137
DME Wipe Snapshot Operations Clip Player Content Operations.................138
(Menu) .............................................122 Video Operations .................................... 140
Recalling Video.........................................140
Playing Video ............................................140
5
Three-Dimensional Transform Operations Cueup & Play ............................................167
(Menu) .............................................150 DDR/VTR Timeline ..................................169
Graphics Display..................................... 151 Disk Recorder File Operations ..................171
Overview ...................................................151 Control of P-Bus Devices ....................... 173
Setting a Graphic .......................................151 P-Bus Timeline..........................................173
Edge Effects ............................................ 152 P-Bus Trigger ............................................174
Setting a Border.........................................152 Control of GPI Devices ........................... 175
Setting a Crop............................................153 GPI Timeline .............................................175
Setting a Wipe Crop ..................................153 Control of Routers .................................. 176
Video Modifier Effects ............................ 155 Destination Input List Display ..................176
Setting Defocus .........................................155 Selecting a Level .......................................176
Setting Sepia..............................................155 Switching the Destination Input ................176
Setting Mono .............................................155
Setting a Mosaic ........................................155
Setting a Mask ...........................................155
Freeze Effects.......................................... 157 Chapter 14 Other Functions
Setting a Freeze .........................................157 Utility Functions ...................................... 177
Nonlinear Effects..................................... 157 List of Utility Commands..........................178
Setting a Nonlinear Effect .........................157 Executing a Utility Function (Utility Control
Setting a Page Turn ...................................157 Block)...............................................179
Setting a Roll .............................................158 Executing a Utility Function (Cross-Point
Other Settings ......................................... 159 Control Block) .................................180
Setting a Background ................................159 Multi Program 2 ....................................... 181
Setting Inversion (Invert) ..........................159 Overview ...................................................181
Setting Separate Sides ...............................159 Setting Multi Program 2 Mode..................182
Removing the Virtual Image .....................159 Multi Program 2 Mode Restrictions ..........183
Setting Key Density ..................................159 AUX Bus Functions................................. 184
Setting a Key Source Signal......................159 Selecting an AUX Bus/Edit Preview Bus
Setting Interpolation Processing................160 Signal ...............................................184
Global Effects .......................................... 161 AUX Mix...................................................184
Overview ...................................................161 AUX Bus Color Corrector.........................185
Setting a Combiner....................................161 Color Backgrounds................................. 188
Setting a Brick ...........................................161 Overview ...................................................188
Setting a Shadow .......................................162 Setting a Color Background ......................188
Image Effect............................................. 190
Overview ...................................................190
Setting the Image Effect Function.............190
Chapter 13 External Devices Executing the Image Effect Function........190
External Device Control.......................... 164 Video Process ......................................... 191
Control of VTRs and Disk Recorders .... 165 Overview ...................................................191
VTR/Disk Recorder Operations (Device Video Process Memory .............................191
Control Block) .................................165 Setting the Video Process Function...........191
VTR/Disk Recorder Status Display ..........166 Safe Title .................................................. 192
6
Copy and Swap ....................................... 193 Saving a Snapshot .....................................217
Overview ...................................................193 Snapshot Operations (Menu) ................. 218
Executing a Copy/Swap ............................193 Recalling a Snapshot .................................218
DME Override .......................................... 194 Saving a Snapshot .....................................219
DME Channel Status Display ................. 195 Snapshot Register Operations .............. 221
Displaying a Snapshot Register.................221
Editing a Snapshot Register ......................222
Key Snapshot Register Operations....... 225
Chapter 15 Effect Timelines Displaying a Key Snapshot Register .........225
Overview .................................................. 196 Editing a Key Snapshot Register...............225
Recalling and Saving an Effect Wipe Snapshot Register Operations..... 227
Timeline ...........................................196 Displaying a Wipe Snapshot Register .......227
Editing an Effect Timeline ........................196 Editing a Wipe Snapshot Register.............227
Attributes ...................................................197 DME Wipe Snapshot Register
Duration and Delay ...................................197 Operations ........................................ 229
Keyframe Path...........................................197 Displaying a DME Wipe Snapshot
Executing an Effect Timeline....................198 Register ............................................229
Effect Timeline List ................................. 198 Editing a DME Wipe Snapshot Register ...229
Displaying the Effect Timeline List ..........198
Setting the Effect Timeline List View.......199
Setting an Effect Timeline ...................... 200 Chapter 17 Shotboxes
Recalling an Effect Timeline.....................200
Saving an Effect Timeline.........................201 Overview .................................................. 230
Creating and Editing an Effect Timeline...201 Shotbox Operations................................ 230
Setting the Duration and Delay .................204 Creating and Editing a Shotbox.................230
Setting the Keyframe Path.........................206 Displaying a Shotbox Register ..................231
Executing an Effect Timeline ................. 209 Editing a Shotbox Register........................232
Executing an Effect Timeline (Utility Control Executing a Shotbox............................... 234
Block)...............................................209 Executing a Shotbox (Flexi Pad Control
Executing an Effect Timeline (Menu).......210 Block)...............................................234
Effect Timeline Register Operations ..... 211 Executing a Shotbox (Utility Control
Displaying an Effect Timeline Register ....211 Block)...............................................234
Editing an Effect Timeline Register..........212 Executing a Shotbox (Cross-Point Control
Block)...............................................234
Executing a Shotbox (Menu).....................235
Chapter 16 Snapshots
Overview .................................................. 215 Chapter 18 Macros
Attributes ...................................................215
Bus Override .............................................216 Overview .................................................. 236
Creating and Editing a Macro ...................237
Snapshot Operations (Flexi Pad Control
Block) ................................................ 216 Executing a Macro.....................................237
Recalling a Snapshot .................................217
7
Macro Operations (Flexi Pad Control Saving a File..............................................262
Block) ................................................ 239 Copying a File ...........................................263
Creating and Editing a Macro ...................239 Deleting a File ...........................................263
Editing a Macro Event...............................241 Renaming a File.........................................263
Macro Operations (Menu)....................... 242 Register Data File Operations................ 264
Creating and Editing a Macro ...................242 Target Category Menus .............................264
Editing a Macro Event...............................243 Loading a File............................................265
Editing a Macro Register...........................246 Saving a File..............................................266
Executing a Macro .................................. 248 Copying a File ...........................................267
Executing a Macro (Flexi Pad Control Deleting a File ...........................................268
Block)...............................................248 Renaming a File.........................................268
Executing a Macro (Utility Control Locking File Loading .............................. 269
Block)...............................................249
Executing a Macro (Cross-Point Control
Block)...............................................249
Macro Attachments................................. 250 Chapter 20 Content Management
Overview ...................................................250
Setting a Macro Attachment......................250 Overview .................................................. 270
Displaying a Macro Attachment List ........252 Content Operations................................. 271
Executing a Macro Assigned in a Macro Displaying Content....................................271
Attachment.......................................253 Copying Content........................................274
Macro Timelines ...................................... 254 Moving Content.........................................274
Overview ...................................................254 Deleting Content........................................275
Creating a Macro Timeline .......................254 Locking Content ........................................275
Editing Content Properties ........................275
Combining Content................................. 276
Importing/Exporting Content ................. 278
Chapter 19 File Management Importing Content .....................................278
Overview .................................................. 255 Importing a Content Archive File .............279
Package Operations................................ 256 Exporting a Content Archive File .............279
Displaying a Package ................................256 Editing a Folder ....................................... 280
Copying a Package ....................................257 Editing a Tag............................................ 281
Deleting a Package ....................................258
Locking a Package ....................................258
Editing Package Properties........................258 Chapter 21 System Setup
Importing/Exporting a Package Archive
File ...................................................259 Setting Startup ........................................ 282
Batch File Operations ............................. 260 Saving and Recalling Setup Data ..............282
Loading Files.............................................260 Setting the Startup Mode...........................283
Saving Files ...............................................260 Applying Initial Status File Settings .........283
Copying Files ............................................260 Initializing the System...............................284
Setup Data File Operations .................... 262 Setting the System Configuration ......... 285
Target Category Menus .............................262 Setting Dual Simul Mode ..........................285
Loading a File............................................262 Setting M/E Split .......................................286
8
Setting a GPU............................................286 Copying a Cross-Point Assign Table .... 305
Setting DME Channel Enhanced Function Copying a Table ........................................305
Mode ................................................286 Copying a Table to a Remote Panel ..........305
Setting the Signal Format....................... 287
Setting the Signal Format and
Frequency.........................................287
Setting the Reference Signal .....................287 Chapter 23 Switcher Setup
Setting the Image Switch Timing..............287
Setting the Switcher Configuration ....... 306
Setting the Reference Phase ......................287
Setting a Switcher Bank ............................306
Setting the Dynamic Range.......................288
Setting the Operation Mode and Output for a
Setting the Input Signal .......................... 290 Switcher Bank..................................306
Setting a Source Name ..............................290 Setting Extended Re-Entry ........................308
Selecting Inputs Configurable with a Color Setting a DME Channel.............................309
Corrector/HDR Converter................290
Setting a User Region................................309
Setting a Frame Delay ...............................290
Setting a Multi Viewer ............................. 309
Setting a Frame Synchronizer ...................291
Assigning Signals ......................................310
Setting a Format Converter .......................291
Displaying a Signal Name.........................310
Setting a Color Corrector ..........................292
Setting a DME External Input (Ext In).... 311
Setting an HDR Converter ........................293
Setting the Transition Mode................... 311
Setting the Output Signal ....................... 296
Setting the Transition Preview Mode ........311
Assigning an Output Signal.......................296
Setting the Independent Key Transition
Selecting Outputs Configurable with a Color Mode ................................................311
Corrector/HDR Converter................296
Setting Flip-Flop Mode .............................311
Setting Through Mode ..............................297
Setting the Preset Color Mix Mode...........312
Setting the Video Clip Function................297
Enabling/Disabling Fade-To-Black...........312
Setting the Safe Title Area ........................297
Setting the DME Wipe Edge Softness
Setting a Format Converter .......................297 Function ...........................................312
Setting an HDR Converter ........................298 Setting the Fader Lever Operation
Enabling/Disabling an SDI Output Mode ................................................312
Connector.........................................299 Keys/Wipes .............................................. 313
Setting the Key Memory Mode .................313
Setting the Mask/Border Processing
Mode ................................................313
Chapter 22 Cross-Point Setup
Setting the Key Priority Mode...................313
Creating a Cross-Point Assign Table.... 301 Setting the Cross-Point Hold Operation
Creating the Main Table............................301 Mode ................................................313
Creating Tables 1 to 14 .............................301 Setting the Operation Mode When the Pattern
Setting the Shift Button .............................302 Limit is Released..............................314
Assigning a Cross-Point Assign Setting the Default Wipe Edge Softness ...314
Table .................................................. 303 Enabling/Disabling Video Process
Setting a Source Signal .......................... 303 Memory............................................314
Setting a Source Name ..............................303 Setting Key Auto Drop..............................314
Setting the Source Color ...........................303
Setting the Cross-Point Delay................ 304
9
Setting High Tally .....................................329
Chapter 24 Control Panel Setup Adjusting the Control Panel Buttons/
Setting the Control Panel Display............................................... 330
Configuration.................................... 315 Setting Sleep Mode ...................................330
Assigning a Switcher Bank .......................315 Adjusting the Button/Display
Setting Switcher Banks in Multi Program 2 Brightness ........................................330
Mode ................................................315 Setting the Lit State of Buttons When
Inhibiting Switcher Bank Operation .........315 Off ....................................................330
Inhibiting Key Operation ..........................315
Setting Dual M/E.......................................316
Setting Regions Selected
Chapter 25 External Device Setup
Simultaneously.................................316
Assigning Control Panel Buttons .......... 317 Setting Parallel Input Ports .................... 331
Assigning a Utility Function................... 318 Assigning a GPI Input ...............................331
Setting an Action .......................................318 Setting a GPI Input .................................. 332
Inhibiting DME Channel Operations...... 319 Setting Parallel Output Ports ................. 333
Setting Cross-Point Button Rows in the Assigning a GPI Output ............................333
Cross-Point Control Block .............. 320 Setting a GPI Output ............................... 334
Setting the Operation Mode of a Button Setting the Connection Port of External
Row..................................................320 Devices.............................................. 335
Setting Buttons and Indicators ..................320 Setting the Connection Port.......................335
Setting the Display ....................................321 Setting a P-Bus Compatible Device ..........335
Setting Utility Bus Mode...........................321 Setting a VTR............................................335
Setting External Devices ........................ 322 Setting a Disk Recorder (VDCP) ..............336
Setting the P-Bus Control Mode ...............322 Setting a Disk Recorder (Odetics).............337
Setting the AUX Bus Override Mode .......322 Setting an AMP Compatible Device .........337
Setting Channel Selection Buttons ............322 Setting a TCP/IP Connected Device .........338
Setting a Router ...................................... 323
Assigning a Destination ............................323
Assigning a Source Table..........................323
Setting Levels ............................................323 Chapter 26 Router/Tally Setup
Setting the Display/Operation Mode ..... 324
Setting the NS-Bus Matrix ...................... 339
Setting Source Names and Destination
Assigning Switcher Inputs/Outputs...........339
Names ..............................................324
Setting an External Box.............................339
Setting the Transition Operation Buttons and
Display Mode...................................324 Selecting an Alias Name Group ................340
Setting the Mode of Buttons in the Cross-Point Setting a Tally Group .............................. 341
Control Block...................................326 Setting Wiring.......................................... 341
Setting the Mode of Buttons in the Flexi Pad Setting Tally Generation......................... 342
Control Block...................................326 Setting Advanced Tally........................... 343
Setting the Mode of Buttons and Trackball in Setting Tally Copy................................... 343
the Device Control Block ................327 Setting a Parallel Tally ............................ 344
Setting the Effect Timeline Mode .............327 Setting a Serial Tally ............................... 345
Setting the Macro Mode ............................328
10
Setting the Time Zone ...............................359
Chapter 27 Link Setup Setting the Date/Time................................359
Setting a Cross-Point Button Link......... 346 Firmware Version Management and
Setting a Bus Link .....................................346 Installation ........................................ 360
Setting an M/E Link ................................. 347 Displaying Package Status ........................360
Setting a Key Link ................................... 348 Installing a Package...................................360
Setting a Transition Link...........................348 Managing and Installing Licenses......... 361
Setting a Color Corrector Link Group ... 349 Displaying the License Status ...................361
Setting a Bus and Destination Link....... 349 Installing/Uninstalling a License...............361
Setting a Matrix.........................................349 Configuring Users and Groups.............. 362
Setting a Bus..............................................349 Configuring a User Account......................362
Setting a Link Table ..................................350 Configuring a Group .................................363
Configuring SNMP .................................. 364
Enabling/Disabling SNMP ........................364
Configuring an MIB Object ......................364
Chapter 28 Maintenance Configuring SNMP v1 and SNMP v2c .....365
11
Overview Chapter 1
All other signal formats are supported only for input
Introduction signals and output signals.
System configuration devices Signal format generic Signal format notation in this
term manual
The principal components of the XVS-G1 system are as
4K format • 2160P 2SI a)
follows.
HD format • 1080P b)
Configuration device Terms used in this manual • 1080i
Multi Format Switcher • XVS-G1 • 720P
XVS-G1 • Switcher SD format • 576i
• Multi format switcher • 480i
Compact Control Panel • ICP-X1224 a) Supports SMPTE ST 425-5/SMPTE ST 2082-1, level A, 2-sample
ICP-X1224 • Control panel interleave division (2SI).
• Compact control panel b) Supports SMPTE ST 425-1, level A.
12
• Image effect function
• Menu: Items related to DMEs
• Control panel: Buttons related to DMEs
• XZS-G1610 3D DME License
For details about the timing and version for support,
contact your Sony service or sales representative.
13
Names and Functions of
Parts Chapter 2
Control Panel
f e
b c d
14
a M/E banks (switcher banks) b Cross-point control block (see page 15)
Each bank is comprised by a cross-point control block, The ICP-X1216 and ICP-X1116 each have 16 cross-point
transition control block, and Flexi Pad control block. By buttons.
default, M/E-1 and P/P switcher banks are assigned in
order to the banks from the back. c Transition control block (see page 18)
The ICP-X1124 and ICP-X1116 have only one M/E bank
row. By default, the P/P switcher bank is assigned to the d Flexi Pad control block (see page 20)
bank.
You can change the switcher bank assignments. e Device control block (see page 21)
For details, see “Assigning a Switcher Bank” (page 315). f Utility control block (see page 25)
1st row
2nd row
b d
3rd row
4th row
15
a Cross-point button rows b Display
The display shows the following information.
Name Description • Settings of buttons on the 1st row to 4th row (signal
1st row • Selects the bus or utility/shotbox bank name, bus name, register name, or function name
when in key/AUX bus delegation mode. assigned to the button)
• Selects the bus signal assigned by the • Macro register name of macro attachment assigned to
delegation buttons in the function button the 1st row to 4th row buttons
section when in key bus mode or free When the [SHIFT] button function is set, “SHFT” appears
assign mode.
on the display. When the shifted state is selected, “SHFT”
Selects the utility function when a utility/
shotbox bank is assigned using the
is displayed inverted, and the button information also
delegation buttons in the function button toggles to show the shifted state display.
section.
Display mode
• Selects the DME external video bus signal
when in utility bus mode.
Six types of display mode can be set according to the
• Selects the background A bus signal information to display. You can switch the mode using the
(shifted state) when in dual background [DISP MODE] button assigned to the function button
bus mode. section. The display can also be subdivided (top and
2nd row • Selects the bus signal or utility function
bottom) to display two pieces of information.
assigned by the 1st row delegation buttons
when in key/AUX bus delegation mode. For details, see “Setting the Display” (page 321).
• Selects the bus signal assigned by the
delegation buttons in the function button c Cross-point indicators
section when in key bus mode or free When lit, these indicate the source color of the video signal
assign mode. assigned to buttons on the 3rd row.
Selects the utility function when a utility/ If a signal cannot be selected, because a signal is not
shotbox bank is assigned using the assigned or the inhibit setting is set, the indicator is not lit.
delegation buttons in the function button You can disable the cross-point indicators so that they do
section.
not turn on.
• Selects the DME utility 1 bus or 2 bus
signal when in utility bus mode.
• Selects the background B bus signal For details, see “Setting the on/off state of cross-point
(shifted state) when in dual background indicators” (page 320).
bus mode.
3rd row • Selects the background A bus signal when
d Function button section (assignable buttons)
in key/AUX bus delegation mode or key bus You can assign functions, such as settings and operations,
mode. of the cross-point button rows in the Home > Setup > Panel
• Selects the bus signal assigned by the > Module > Button Assign menu (19104.21).
delegation buttons in the function button
section when in free assign mode. For details about assigning buttons, see “Assigning
Selects the utility function when a utility/ Control Panel Buttons” (page 317).
shotbox bank is assigned using the
delegation buttons in the function button
section. Function name Button name Description
• Selects the utility 1 bus signal when in
Row-n Background A Assigns background A
utility bus mode. A a) b) B and B buses to the 1st
4th row • Selects the background B bus signal when Row-n Background row to 4th row.
in key/AUX bus delegation mode or key bus B a) b) n = 1 to 4
mode. Row-n Utility1 a) c) UTIL1 Assigns utility 1 and 2
• Selects the bus signal assigned by the Row-n Utility2 a) c) UTIL2 buses to the 1st row to
delegation buttons in the function button 4th row.
section when in free assign mode. n = 1 to 4
Selects the utility function when a utility/ Row-n DME DME EXT Assigns DME external
shotbox bank is assigned using the External a) c) video bus to the 1st
delegation buttons in the function button row to 4th row.
section. n = 1 to 4
• Selects the utility 2 bus signal when in Row-n DME Utility1 DME UTIL1 Assigns DME utility 1
utility bus mode. a) c)
DME UTIL2 and 2 buses to the 1st
Row-n DME Utility2 row to 4th row.
a) c)
n = 1 to 4
16
Function name Button name Description Function name Button name Description
Row-n Key1 to KEY1 to Assigns key 1 to 8 Aux Mix b) f) AUX MIX Executes an AUX mix
Key8 a) c) d) KEY8 buses to the 1st row to when an AUX bus is
4th row. assigned to the 2nd
n = 1 to 4 row.
Row-n Edit Preview EDIT PVW Assigns edit preview Row-n Key a) b) KEY Selects the signal on
a) b) bus to the 1st row to the key side in the 1st
4th row. row to 4th row.
n = 1 to 4 n = 1 to 4
Row-n FM Source1 FMS1 Assigns frame memory Key b) f) KEY Selects the signal on
a) b)
FMS2 source 1 and 2 buses the key side in the 2nd
Row-n FM Source2 to the 1st row to 4th row.
a) b)
row.
Row-n Image Effect IMAGE Sets the image effect
n = 1 to 4 g) h)
function on background
Row-n DME1 Video DME1V to Assigns DME1 to A bus or B bus on the
to DME4 Video a) b) DME4V DME4 video buses to 1st row to 4th row.
the 1st row to 4th row. n = 1 to 4
n = 1 to 4
Row-n Protect e) PROT Inhibits button
Row-n DME1 Key DME1K to Assigns DME1 to operation on the 1st
to DME4 Key a) b) DME4K DME4 key buses to the row to 4th row.
1st row to 4th row. n = 1 to 4
n = 1 to 4
Utility a) f) UTIL Assigns the bus when
Row-n Utility/ UTIL/SBOX1 Assigns utility/shotbox in utility bus mode to
Shotbox1 to Utility/ to UTIL/ banks 1 to 10 to the 1st the 1st row to 4th row.
Shotbox10 a) c) SBOX10 row to 4th row.
Shift All Bus SHIFT ALL Switches the cross-
n = 1 to 4
point button rows of all
Row-n Aux1 to AUX1 to Assigns AUX1 to 48 buses to the shifted
Aux48 a) b) AUX48 buses to the 1st row to state.
4th row.
Dual BKGD Bus f) DUAL BKGD Switches to dual
n = 1 to 4
BUS background bus mode.
Row-n Xpt Hold d) XPT HOLD Sets cross-point hold
e) Xpt Inhibit INHBT SET Sets/releases inhibit
for the buses assigned
mode for cross-point
to the 1st row to 4th
buttons.
row.
n = 1 to 4 Xpt Inhibit All Clear INHBT ALL Releases inhibit mode
CLR for all cross-point
Pre Macro PRE MCRO Sets macro attachment
buttons.
in pre-macro mode.
Post Macro POST MCRO Sets macro attachment a) Disabled in key/AUX bus delegation mode.
in post-macro mode. b) Disabled in key bus mode.
c) 3rd row and 4th row are disabled in key bus mode.
Macro Attach MCRO Enables macro d) Disabled for SL keys.
Enable ATTCH ENBL attachments assigned e) 1st row is disabled in key/AUX bus delegation mode.
to buttons in the f) Disabled in free assign mode.
switcher banks. g) 1st row and 2nd row are disabled in key bus mode.
h) 1st row and 2nd row are disabled in key/AUX bus delegation mode.
Main MAIN Switches the button
operation to the
function on the main
side when in multi
program 2 mode.
Sub SUB Switches the button
operation to the
function on the sub
side when in multi
program 2 mode.
Display Mode DISP MODE Switches the display
mode.
Row-n Aux Mix a) b) AUX MIX Executes an AUX mix
when an AUX bus is
assigned to the 1st row
to 4th row.
n = 1 to 4
17
Transition Control Block
The transition control block is used to execute transitions. For details, see “Chapter 5 Transitions” (page 53).
It supports common transitions and independent key
transitions.
b d
a c
18
Function Button name Description Function Button name Description
name name
NAM NAM Selects NAM (non-additive Sub SUB Switches operation to the
mix). function on the sub side in
multi program 2 mode.
Super Mix SUPER MIX Selects super mix.
Preset Color PST COLOR Selects preset color mix. c Display
Mix MIX
The display shows the following information.
Wipe WIPE Selects wipe. • Left-side display:
DME Wipe DME WIPE Selects DME wipe. Target switcher bank name (M/E1 to M/E5, P/P)
FM1&2 Clip to FM1&2 CLIP Selects clip transition. Main and sub assignment status when in multi program
FM15&16 Clip to FM15&16 2 mode (MAIN, SUB, MAIN&SUB)
CLIP • Right-side display:
Transition rate
Wipe direction selection buttons During key priority setting operation, the display shows
Function Button name Description the following information.
name • Left-side display:
Normal NORM The wipe proceeds in the
State (displayed inverted when on) and priority of key 1
direction from black to white to key 4
of the pattern images, Main and sub assignment status when in multi program
shown in “Wipe Pattern 2 mode (M, S)
List” (page 366), or in the • Right-side display:
direction of the arrows
(normal).
State (displayed inverted when on) and priority of key 5
to key 8
Normal/ NORM/REV The wipe direction Main and sub assignment status when in multi program
Reverse alternates between normal
and reverse after each 2 mode (M, S)
transition.
Reverse REV The wipe proceeds in the
d Independent key transition execution section
opposite direction of normal (assignable buttons)
(reverse). You can assign executions buttons for independent key
transitions in the Home > Setup > Panel > Module >
Transition preview buttons Button Assign menu (19104.21).
Function Button name Description
name For details about assigning buttons, see “Assigning
Control Panel Buttons” (page 317).
Transition TRANS PVW Switches the transition
Preview preview mode.
You can check a transition
using preview output. Function Button name Description
name
Pattern limit setting buttons Key1 KEY1 Inserts or removes a key
Transition to TRANS to automatically with the set
Function Button name Description Key8 KEY8 transition rate and transition
name Transition TRANS type.
During the transition, the
Limit Set LIMIT SET Sets the pattern limit.
button is lit amber.
Pattern Limit PTN LIMIT Enables the pattern limit.
Key1 On to KEY1 ON to Inserts or removes a key
Key8 On KEY8 ON instantaneously.
Main/sub switching buttons (multi program 2 If a key is currently
mode) inserted, the button is lit
amber.
Function Button name Description
name
Main MAIN Switches operation to the
function on the main side in
multi program 2 mode.
Simultaneously pressing
the [SUB] button activates
both the main and sub
operations.
19
Flexi Pad Control Block
The Flexi Pad control block is used for recalling and Function Button name Description
saving snapshots, wipe snapshots, DME wipe snapshots, name
and key snapshots, for recalling and creating macros, for Wipe WIPE Switches to wipe snapshot
recalling shotboxes, for entering the transition rate, and for operation mode.
other tasks. In wipe snapshot operation
mode, you can save and
recall a wipe snapshot and
a select a wipe pattern.
DME Wipe DME WIPE Switches to DME wipe
snapshot operation mode.
In DME wipe snapshot
operation mode, you can
save and recall a DME wipe
snapshot and select a DME
wipe pattern.
Snapshot SNAPSHOT Switches to snapshot
operation mode.
In snapshot operation
mode, you can save and
recall snapshots, and add
attributes.
Shotbox SHOTBOX Switches to shotbox
operation mode.
In shotbox operation mode,
you can recall and execute
shotboxes.
Macro MCRO Switches to macro
operation mode.
In macro operation mode,
b
press and hold the [MCRO]
button and press a button
(for the target register) in
a Mode selection buttons / operation buttons / bank the memory recall section
selection buttons (assignable buttons) to enter edit mode.
You can assign mode/bank selection buttons and operation In macro operation mode,
buttons in the Home > Setup > Panel > Module > Button you can save, recall, and
edit macros.
Assign menu (19104.21).
Transition Rate TRANS Switches to transition rate
For details about assigning buttons, see “Assigning RATE operation mode.
In transition rate operation
Control Panel Buttons” (page 317). mode, you can enter a
transition rate.
Mode selection buttons
[UNDO] button / [DEL] button
Function Button name Description
name Function Button name Description
name
Key KEY Switches to key operation
mode. Undo UNDO After recalling a register,
In key operation mode, you returns to the state before
can carry out the following the register was recalled.
operations.
Delete DEL Press and hold the [DEL]
• Saving and recalling key
button and press a register
snapshots button in the memory recall
• Selecting independent section to delete the
key transition type register data.
• Selecting the key fill
signal or key source
signal in the cross-point Notes
control block • The [UNDO] button and [DEL] button cannot be used in
shotbox operation mode.
20
• The [UNDO] button cannot be used in macro operation b Memory recall section (memory recall buttons)
mode. Also, the [DEL] button cannot be used in edit This section displays the functions assigned to the buttons
mode. for the selected operation mode.
The top right button is used to display the selected pattern
Bank selection buttons number, register number, macro event number, transition
Function Button name Description
rate input value, and other status display (excluding in key
name operation mode).
When a macro is recalled in macro operation mode, the
Bank0 to BANK0 to The memory recall section
Bank25 BANK25 switches to the register bottom center button displays the executed event number
display for the selected and the total number of events.
bank.
Numeric keypad mode
Bank Select BANK SEL Enter a bank number to
switch the memory recall
Pressing the [BANK SEL] button, [PTN NO.] button, or
section to the register [PAUSE] button switches the memory recall section to
display for the selected numeric keypad mode, where you can enter bank numbers,
bank. wipe pattern numbers, and pause event times.
The currently set numeric value or the value entered in
numeric keypad mode is displayed on the top right button.
21
Mode selection buttons Notes
Function Button name Description • When multiple channels are selected, the first selected
name button becomes the reference, and is lit green.
Menu MENU • Switches to menu Subsequent selected buttons are lit amber.
parameter operation • [CH1] to [CH8] and [K1RSZ] to [K8RSZ] share the
mode. same buttons.
• You can adjust
parameters (numbers 1
b Operation buttons (assignable buttons)
to 3) of the currently
displayed menu using the
You can assign buttons for use in each operation mode in
trackball and Z-ring. the Home > Setup > Panel > Module > Button Assign
• Press the [MENU] button menu (19104.21).
twice, turning it on green,
to fix the target of the For details about assigning buttons, see “Assigning
trackball and Z-ring to the Control Panel Buttons” (page 317).
parameter currently being
adjusted. Resizer operation mode
Run Control RUN CTRL • Switches to run control This mode is used for two-dimensional transform
operation mode. operations on images using a resizer.
• Enables operation of the
currently recalled effect For details about resizer operations, see “Resizer”
timeline using the Z-ring. (page 89).
M/E-1 to M/E-5 M/E1 to M/E5 • Switches to resizer
P/P P/P operation mode.
• The first selected button Function Button name Description
becomes the reference, name
and is lit green. Aspect/ ASP PERS Adjusts the aspect ratio of a
Subsequent selected Perspective key using the trackball or Z-
buttons are lit amber. ring.
DME DME • Switches to three- Location Size LOC SIZE • Moves a key using the
dimensional transform trackball.
operation mode. • Scales a key (shrink/
Device DEV • Switches to device/frame magnify) using the Z-ring.
memory/clip player Rotation ROT • Rotates a key using the
operation mode. trackball.
• Adjusts the perspective of
Channel selection buttons a key using the Z-ring.
22
Function Button name Description Function Button name Description
name name
X X • Restricts the parameters Border/Crop BDR/CROP • When the [BDR/CROP]
Y Y targeted by the operation. button is pressed (lit
Z Z When the [X] button is lit: amber):
Operations on Adjusts the border width
parameters on the X-axis of a key using the
using the trackball are trackball or Z-ring.
enabled. • When the [BDR/CROP]
When the [Y] button is lit: button is pressed while
Operations on pressing the [SHIFT]
parameters on the Y-axis button (lit green):
using the trackball are Adjusts the crop width of
enabled. a key using the Z-ring.
When the [Z] button is lit:
Operations on Three-dimensional transform operation mode
parameters on the Z-axis This mode is used for three-dimensional transform
(Z-ring adjustment items) operations on images using a DME.
using the Z-ring are
enabled. For details about DME operations, see “Three-
• When the [ROT] button is Dimensional Transforms” (page 147).
lit, the [X] button and [Y]
button select the direction
of rotation. Function Button name Description
• When the [BDR/CROP] name
button is lit green, the [X]
Local LOCAL Selects local space.
button, [Y] button, and [Z]
button select the edge Global GLB Selects global space.
(top edge, left edge, right Source SRC Selects source space.
edge) to crop.
Target TRGT Selects target space.
Fine FINE Switches to fine mode,
enabling fine adjustment Aspect/ ASP PERS • When the [ASP PERS]
control of setting values Perspective button is pressed in
using the trackball and Z- source space:
ring. Adjusts the aspect ratio
M/E Default M/E DEF When the [M/E DEF of an image using the
Recall RCALL RCALL] button is pressed trackball or Z-ring.
twice: • When the [ASP PERS]
Returns the switcher bank button is pressed while
to the initial settings. pressing the [SHIFT]
Center CTR • When the [CTR] button is button in source space:
pressed once: Adjusts the skew of an
Adjusts the two- image using the trackball.
dimensional transform • When the [ASP PERS]
parameters to the detent button is pressed in
positions. target space:
• When the [CTR] button is Adjusts the viewpoint
pressed twice, or the position (perspective of
[CTR] button is pressed an image) using the
once while pressing the trackball or Z-ring.
[SHIFT] button: Location Size LOC SIZE • Moves an image using
Returns the two- the trackball.
dimensional transform • Scales an image (shrink/
parameters to the default magnify) using the Z-ring.
values. Location XYZ LOC XYZ Moves an image using the
• When the [BDR/CROP] trackball or Z-ring.
button is lit green, the
[CTR] button selects the Rotation ROT Rotates an image using the
trackball or Z-ring.
edge (bottom edge) to
crop.
23
Function Button name Description Menu parameter operation mode
name Used to set menu parameters.
Shift SHIFT Used in combination with
the [ASP PERS], [ROT], For details about menu parameter operations, see
[CTR], and [CLR WORK “Setting Parameters” (page 40).
BUFR] buttons.
Clear Work CLR WORK • When the [CLR WORK
Buffer BUFR BUFR] button is pressed Function Button name Description
once: name
Returns the three- X X Restricts the parameters
dimensional transform Y Y targeted by the operation.
parameters to the initial Z Z When the [X] button is lit:
settings. Operations on parameter
• When the [CLR WORK number 1 using the
trackball are enabled.
BUFR] button is pressed
When the [Y] button is lit:
twice, or the [CLR WORK Operations on parameter
BUFR] button is pressed number 2 using the
once while pressing the trackball are enabled.
[SHIFT] button: When the [Z] button is lit:
Returns all DME Operations on parameter
parameters to the initial number 3 using the Z-ring
settings. are enabled.
Axis Location AXIS LOC Moves the rotation axis of Fine FINE Switches to fine mode,
an image using the enabling fine adjustment
trackball or Z-ring. control of setting values
using the trackball and Z-
X X Restricts the parameters ring.
Y Y targeted by the operation.
Z Z When the [X] button is lit: Device/frame memory/clip player operation mode
Operations on parameters
on the X-axis using the
This mode controls operations of devices such as VTRs/
trackball are enabled. disk recorders and operations of frame memory/clip
When the [Y] button is lit: players.
Operations on parameters
on the Y-axis using the For details about device operations, see “Control of VTRs
trackball are enabled.
When the [Z] button is lit:
and Disk Recorders” (page 165).
Operations on parameters
on the Z-axis (Z-ring For details about frame memory operations, see “Playing
adjustment items) using the Video” (page 133).
Z-ring are enabled.
Fine FINE Switches to fine mode, For details about clip player operations, see “Playing
enabling fine adjustment Video” (page 140).
control of setting values
using the trackball and Z-
ring. c Trackball
This adjusts the parameters of items selected in resizer
Center CTR • When the [CTR] button is
operation mode, three-dimensional transform operation
pressed once:
Adjusts the three-
mode, and menu parameter operation mode.
dimensional transform
parameters to the detent d Z-ring
positions. This adjusts the parameters of items selected in resizer
• When the [CTR] button is operation mode, three-dimensional transform operation
pressed twice, or the mode, and menu parameter operation mode.
[CTR] button is pressed It is used for playback operations in device/frame memory/
once while pressing the clip player operation mode.
[SHIFT] button: It can control an effect timeline in run control operation
Returns the three- mode.
dimensional transform
parameters to the default
values.
24
Utility Control Block
The utility control block is used to execute functions
assigned to memory recall buttons, execute effect
timelines, and enter menu parameters.
a c
a Mode selection buttons / operation buttons / bank Function Button name Description
selection buttons (assignable buttons) name
You can assign mode/bank selection buttons and effect Normal NORM Sets the effect timeline
timeline operation buttons in the Home > Setup > Panel > execution direction to
Module > Button Assign menu (19104.21). normal (from beginning to
end).
For details about assigning buttons, see “Assigning Normal/ NORM/REV Sets the effect timeline
Control Panel Buttons” (page 317). Reverse execution direction to
normal/reverse (toggles
each time execution
Mode selection buttons finishes).
Function Button name Description Reverse REV Sets the effect timeline
name execution direction to
reverse (from end to
Util/Shotbox UTIL/SBOX Switches to utility/shotbox beginning).
operation mode.
You can execute functions Rewind REWIND When the execution
assigned to the memory direction is normal, moves
recall section. the effect timeline to the
start point.
Menu MENU Switches to menu When the execution
parameter operation mode. direction is reverse, moves
You can adjust parameters the effect timeline to the
(numbers 1 to 5) of the stop point.
currently displayed menu
using the adjustment Run RUN Executes an effect timeline.
knobs.
Bank selection buttons
Effect timeline operation buttons
Function Button name Description
Function Button name Description name
name Bank1 to BANK1 to Switches the memory recall
Effect Loop EFF LOOP Repeatedly executes an Bank20 BANK20 section to function recall
effect timeline. mode of the selected bank.
25
Function Button name Description
name
Bank Select BANK SEL Entering a bank number
switches the memory recall
section to function recall
mode of the selected bank.
c Adjustment knobs 1 to 5
Used to set menu parameters.
26
Power Supply and Connectors
Front view
a b c
d
e
27
For details, see “Resetting the password of the
administrator user account” (page 35).
Rear view
d c b a
e
s
f
r
g q
h p
o
jk l m n
28
Can also be used as a tally input/output port. s REMOTE 1/2, 3/4, 5/6, 7/8 connectors (RJ-45, RS-
422 compliant)
o Network expansion 4 connector Can be used when an XKS-G1700 Legacy Interface Board
p Network expansion 3 connector (option) is installed.
q Network expansion 2 connector Connect to a device that supports VTR (Sony 9-pin VTR
r Network expansion 1 connector protocol), disk recorder (Video Disk Communications
PCIe slot. Supports third-party network expansion cards. Protocol, Odetics protocol), or P-Bus (Peripheral Bus II
Used as interface expansion 1 to 4 LAN connectors. protocol) protocols.
Can also be used as a tally output port.
For details, see “Setting the Network Interface”
(page 357).
Rear view
The following illustration shows the ICP-X1224.
a b c d e
a DC IN A and B connectors
Connect to the supplied AC adaptor.
29
Input Connectors and Output Connectors
INPUT OUTPUT
Input/output connector numbers are assigned from left to Transfer of 4K signal as a single signal
right on the 1st, 2nd, 3rd, and 4th connector boards in that A 4K signal is assigned to a single connector.
order. The assignment is as follows.
Input/output connectors on the 3rd and 4th connector
boards can be used when XKS-G1110 Additional I/O 4K format input signal/ Connector number
output signal
Boards (option) are installed.
When the system signal format is 2160P, only the input/ 1st system 1
output connectors on the 1st and 2nd connector boards can 2nd system 2
be used. 3rd system 3
(and so on) (and so on)
4K signal input/output connector
assignment SDI output connector disable setting
Transfer of subdivided-by-4 image (sub images) SDI output connectors can be enabled/disabled. When
as four separate signals disabled, no signal is output from the output connector.
A 4K signal is assigned as a group of four connectors. If a cable is not connected to an enabled output connector,
The assignment is as follows. radio wave interference may occur. Disable unused output
connectors.
4K format input signal/ Connector number
output signal
For details, see “Enabling/Disabling an SDI Output
1st system 1, 2, 3, 4 Connector” (page 299).
2nd system 5, 6, 7, 8
3rd system 9, 10, 11, 12
(and so on) (and so on)
30
Menu
The menu is used configure data management, setup, and For details about menu operations, see “Chapter 3 Menu
other settings related to the switcher and control panel. It Operation” (page 34).
can also be used to configure transitions, keys, and image
creation settings using menu operations.
Screen Structure
Header
area
Menu Menu
selection display
area area
Menu
selection
area
Taskbar
area
Header area
a b c d e f g h i
31
Press and hold a button to display a pull-down list to select i Overflow button
and recall a menu from the history. Displays items that are not displayed in the header area.
Press the overflow button to display a pull-down list to
c Menu number button select the following items.
Displays the menu number. A heart-shaped icon is System Configuration
displayed for menus registered as favorites. Displays the System Configuration menu.
Press the menu number button to display the numeric User’s Guide
keypad window, and enter a menu number to recall the Displays the XVS-G1 User’s Guide.
corresponding menu. End-User License Agreement
Displays the software license information.
d Menu path System Shutdown
Displays the menu path. Shuts down the system.
System Reboot
e Macro edit indicator Reboots the system.
Displays [Macro Menu Enbl] during macro editing using Sign Out
the menu when auto insert mode is disabled. Signs out from the web menu.
Displays [Macro Auto Ins] during macro editing using the
menu when auto insert mode is enabled.
Menu selection area
f Unapplied / unsaved indicator Selects the 2nd, 3rd, 4th, and 5th level in the menu
Displays [Unapplied *] when there is a setting value not hierarchy.
applied in the menu.
Displays [Unsaved *] when there is content that is not For details, see “Menu Selection” (page 37).
saved in content storage.
Menu display area
g Panel link button
The connected control panel (1 or 2) and a link icon are Displays the menu operation buttons, target list of
displayed. operations, status of settings, and other information.
Press the panel link button to link the control panel with When adjusting parameters, an analog controls section
the menu. appears on the right.
For details, see “Linking a Control Panel with the Menu” For details, see “Basic Menu Operation” (page 37).
(page 43).
Taskbar area
h Messages indicator button
Displays shortcuts for frequently used menus and
Displays the number of messages when there is updated
functions commonly used in parallel with the current
error information.
menu.
Press the messages indicator button to check information
Five types of taskbar can be used.
about the occurrence and resolution of errors.
For details, see “Switching Taskbars” (page 42).
Pop-up Window
Depending on the menu button, a pop-up window may be
displayed in the menu display area when the button is
pressed.
32
Numeric Keypad Window For details, see “Analog Controls Window” (page 41).
Displays a numeric keypad for entering numbers.
Message window
a b Displays operation confirmations and other messages, as
required.
c d e
a Setting range
Displays the minimum and maximum values for settings
with a range.
b Backspace button
Deletes the rightmost number/character of an entered
value.
c TC button
Changes the input mode to enter timecode values. Set to on
for timecode input mode, and set to off for frame number
input mode.
d – (minus) button
Changes the sign of the input value. Set to on for negative
values.
e Trim button
Changes a setting value by the entered difference value.
33
Menu Operation
1
Chapter 3
Access the certificate download page.
Overview Enter the URL of the certificate download page in a
browser.
“http://IP address of download page/doc/Certificate/”
The XVS-G1 menu is a web-based application.
The menu can be operated using the touch panel of a
Note
computer (tablet or PC) connected to the switcher system
network. The menu can also be operated using a mouse. The IP address of the certificate download page is the
In this manual, “press” is used to indicate a tap or click standard interface 1 address set in the System
operation of menu buttons. Configuration > Network > Network Settings menu
(20201.11).
Note It is set to “192.168.100.1” by default.
34
Signing out from the web menu
Signing In / Signing Out Press the overflow button in the header area and select
[Sign Out] from the pull-down list.
The password must be 8 to 32 characters, containing at 1 Press the [SELECT] button until the [Password Reset]
least one single-byte alphabetic character and at least one item appears on the display.
single-byte numeric character.
The display item changes each time the [SELECT]
button is pressed.
Signing in to the web menu
2 Press the [SET] button.
1 Access the web menu.
An execution confirmation message appears.
Enter the URL of the web menu in a browser.
“https://IP address of web menu/” 3 Press the [SET] button.
The web menu sign-in screen appears.
The password is reset.
Note To cancel execution, press the [SELECT] button.
Note
A security warning message may appear when
displaying the menu screen, but continue the
operation.
35
Displaying the User’s Displaying License
Guide Information
You can display the User’s Guide in English or Japanese. Press the overflow button in the header area and select
Press the overflow button in the header area and select [End-User License Agreement] from the pull-down list.
[User’s Guide] from the pull-down list. The software license information is displayed.
Select a language on the User’s Guide link screen to
display the User’s Guide. To display the license information from the sign-
in screen
To display the User’s Guide from the sign-in Press the overflow button displayed on the top right of the
screen sign-in screen and select [End-User License Agreement]
Press the overflow button displayed on the top right of the from the pull-down list.
sign-in screen and select [User’s Guide] from the pull-
down list.
36
Shutting Down / Basic Menu Operation
Rebooting
Menu Selection
Shutting Down the System
Menu hierarchy and menu number
Press the overflow button in the header area and select The menu hierarchy has five levels, with each menu
[System Shutdown] from the pull-down list. having a unique menu number.
In this manual, menu selection operations use the
Note following convention.
The connection between the web menu and switcher is level 1 > level 2 > level 3 > level 4 > level 5 menu (menu
disconnected. number)
Example:
When selecting the menu to import a package
Home > File > Package > Import/Export > Import menu
Rebooting the System (10101.21)
Press the overflow button in the header area and select
Note
[System Reboot] from the pull-down list.
Depending on the menu, level 3 and level 5 may not exist.
Note
The connection between the web menu and switcher is Selecting a menu
disconnected. Sign in to the web menu again. The following five methods are available for selecting
menus.
Level 2 Level 4
Level 3 Level 5
37
Level 2 / level 3:
Level 2 and level 3 menus are displayed in tree format Setting Menu Items
on the left side of the menu selection area.
Menu items are configured, depending on the item, by
You can scroll up/down using a swipe operation or
setting operation buttons on/off, selecting values, or
using the scrollbar slider.
entering values.
Select a level 2 menu to display the level 3 menus
immediately below.
Select a level 3 menu to display the corresponding Types of buttons
level 4 and level 5 menu buttons. The action performed when a button is pressed varies
Level 4 / level 5: depending on the function assigned to the button.
Select level 4 and level 5 menu buttons. Depending on the button, multiple actions may be
Displaying a menu by entering the menu number combined (for example, on/off + parameter setting).
Press the menu number button in the header area.
Button Description
The numeric keypad window appears. Enter a menu
number and press [Enter] to display the selected menu. On/off button
Turns a function on/off (enable/disable).
Selecting a menu from the history
Press the [T] button or [t] button in the header area. Execution button
Executes a function.
Press the [T] button to display the previous recalled
menu, or press the [t] button to display the next recalled Pull-down selection button
menu. Select a value from the pull-down list.
Press and hold the [T] button or [t] button to display a
pull-down list to select and display a menu from the
history. Keyboard input button
Press the input field and enter a character string
Selecting a menu from the [Favorites] taskbar using the keyboard.
Press the taskbar selection button and select [Favorites] Numeric keypad input button
from the pull-down list. Press the input field to display the numeric
Select a menu for display from the menu shortcut buttons keypad window and enter a numeric value.
displayed in the taskbar. Pop-up display button
You can scroll the shortcut button display left/right using Displays a pop-up window for setting/selecting a
a swipe operation. function.
Using a mouse, press and hold the left button and then drag Parameter setting button
to the left or right. Displays the analog controls section for adjusting
parameters.
For details, see “Registering Menus as Favorites” Shortcut button
(page 42). Jumps to the specified menu.
38
Button Status
display
Selecting and Setting List Items
When an on/off switch is set to the on (enable) When the target of an operation is selectable from multiple
position:
items, the items are displayed in a list.
The switch is slid to the right and is displayed in
blue.
When adjusting a parameter:
Select All checkbox Slider
The button is displayed in light blue.
Groups
Number selection button Operation Scrollbar
buttons
List display
You can move the display position in a list using a swipe
operation or using the scrollbar slider in order to select a
target item.
Buttons for related functions are grouped.
The row for the item that has focus is shown in light blue.
A line indicating the group name and range of the group is
When multiple items in a list can be selected, a checkbox
displayed above the buttons.
is displayed on the left side of each item.
Depending on the group, only one button or multiple
buttons within the group may be selected.
Selecting using a checkbox
Tabs To select an item, place a check mark in the checkbox.
To select multiple items, place a check mark for the target
items for operation.
Select All checkbox
To select or deselect all items, use the Select All checkbox.
When there are items selected in a list, a blue square is
displayed in the Select All checkbox.
To select all items, place a check mark in the Select All
checkbox.
To deselect all items, clear the check mark from the Select
All checkbox.
39
Example:
To select list items 1 to 5, enter “1-5”. Parameter display button
To select list items 1, 3, and 5, enter “1,3,5”.
Parameter 1 to 5 buttons
40
Analog Controls Window Entering parameters using the numeric
keypad
Guide display button Press the numeric keypad display button to display the
Numeric keypad Parameter operation area numeric keypad window.
display button Default recall button Enter a setting value for the parameter and press [Enter].
41
Switching Taskbars
Registering Menus as
You can switch between five types of taskbar to display in
the taskbar area. Favorites
Taskbar selection button You can register frequently used menus or other menus as
“favorites.”
A favorite menu can be recalled by pressing a shortcut
button displayed in the [Favorites] taskbar.
Press the taskbar selection button in the taskbar area and Notes
select a taskbar from the pull-down list.
The taskbar area switches to the selected taskbar display. • Up to 100 shortcut buttons can be registered in the
[Favorites] taskbar.
• Shortcut buttons are displayed in the order they were
Types of taskbar registered from the left.
[Favorites] taskbar
Displays shortcuts for registered menus. Register favorite button
42
Linking a Control Panel Entering and Displaying
with the Menu Text/Numbers
You can set a menu to operate by linking it with an Press a numeric keypad input button to display the numeric
operation from a control panel. keypad window and enter a numeric value.
Multiple web menu sessions can be connected
simultaneously, but only one web menu session can be For details, see “Numeric Keypad Window” (page 33).
linked to an operation from a control panel.
The following control panel operations are link targets. Press a keyboard input button and enter alphanumeric
• Setting a parameter in the utility control block in menu characters using a computer keyboard/on-screen
parameter operation mode keyboard/touch panel.
• Setting a parameter in the device control block in menu
parameter operation mode
• Recalling a menu by double-pressing a control panel
Invalid characters for names
button The following characters cannot be used for entering
• Menu shortcut functions of the memory recall buttons in names.
the utility control block and the cross-point buttons in the \ / : * ? " < > |
cross-point control block
Notes
Panel link button
• Characters that cannot be used are replaced with
underscores.
• When entering names shown on control panel buttons
and the display, “|” is used as a line break code.
1 Press the panel link button in the header area. Name settings when multiple items are
The connected control panel and the link icon are
selected
displayed on the panel link button. When setting a name with multiple items selected, the
same name may be set or a consecutive number may be
2 Check the message, then press [OK]. appended to the name depending on the menu.
In the following menus, a consecutive number is appended
The control panel link is set and the link icon turns to the name.
light blue. • Home > Setup > System > Input > Input Adjust menu
If a control panel link is set while the control panel is (19101.31)
linked to another menu session, the other menu link is • Home > Setup > Xpt Assign > Src Name/Src Color >
canceled. Edit Src Name/Color menu (19102.51)
• Home > Setup > Panel > Module > Utility Function
To cancel a link
Assign menu (19104.22)
Press the panel link button, turning it off. The link is
Example:
canceled and the link icon turns gray.
Setting the source name of signals
If three signals are selected as the target and you enter
“CAM”, the name of each signal will become “CAM1”,
“CAM2”, and “CAM3”.
43
Enter a value in “hh:mm:ss:ff”
(hour:minute:second:frame) format. The “:” (colon) is
inserted automatically.
Selecting and Displaying
Example:
To set 3 minutes, 7 seconds, and 15 frames, enter “30715”.
Regions
Frame number input mode
When [TC] in the numeric keypad window is turned off, The term “region” refers to blocks classified by specific
frame number input mode is selected. functions.
Enter a value in “fff” (frame) format. In effect timelines and snapshots, you can select target
regions to save/recall registers. You can also select
multiple regions simultaneously.
Entering a difference from a current value
You can enter a value representing the increase or decrease
from a currently set value to change the setting value. Types of Regions
[Trim] in the numeric keypad window is used to enter a
difference value. The regions are classified as follows.
Enter a positive value and press [Trim] to increase the • Switcher bank regions:
setting value. M/E-1 to M/E-5, P/P, M/E-1 Sub to M/E-5 Sub, P/P Sub
Enter a negative value and press [Trim] to decrease the • User regions:
setting value. User 1 to User 8
• DME regions:
DME 1 to DME 4 (including DME Global)
Abbreviated display of long names • External device regions:
When a file name is too long to be displayed in full on a Device 1 to Device 12, P-Bus, GPI, Macro, Router
button or in a list, “…” is appended to the name.
Notes
Maximum number of valid input characters • In an effect timeline, regions other than Router are the
The maximum number of characters described in this target.
document is the maximum number when using ASCII • In a snapshot, regions other than Device 1 to Device 12,
characters only. P-Bus, GPI, and Macro are the target.
If characters other than ASCII characters are used, the
maximum number of characters that can be entered is User regions
reduced. You can optionally assign the following regions to User 1
to User 8.
The user regions shown in parenthesis are the default
assignments.
• Color Bkgd 1, Color Bkgd 2 (User 1)
• Aux 1 to Aux 48 (User 2)
• Clip Player 1 to Clip Player 4 (User 3)
• Frame Memory 1 to Frame Memory 16 (User 4)
Reference regions
When multiple regions are selected, the reference region is
the display target in the menu.
When a reference region is removed from the target, the
reference region will be set according to the following
order of priority.
M/E-1 > M/E-1 Sub > M/E-2 > M/E-2 Sub > M/E-3 >
M/E-3 Sub > M/E-4 > M/E-4 Sub > M/E-5 > M/E-5 Sub >
P/P > P/P Sub > User 1 > User 2 > User 3 > User 4 > User
5 > User 6 > User 7 > User 8 > DME 1 > DME 2 > DME
3 > DME 4 > Device 1 > Device 2 > Device 3 > Device 4
> Device 5 > Device 6 > Device 7 > Device 8 > Device 9
44
> Device 10 > Device 11 > Device 12 > P-Bus > GPI > • Reference region: Inverted display
Macro > Router
Selecting a Region
When selecting the target region in the menus for effect
timelines and snapshots, the region selection window
appears.
Note
The display of the region selection window varies
depending on the menu.
45
Selecting Signals Chapter 4
Overview
You can select a signal with the cross-point button rows in Depending on the control panel used, each button row has
the cross-point control block of the switcher bank. 24 buttons or 16 buttons.
This section describes control panels with 24-button rows.
1st row
2nd row
Display
Cross-point indicators
3rd row
4th row
Cross-point buttons You use the shift button to switch between the button
The button numbers are labeled on the cross-point buttons number in the shifted state and the button number in the
of the cross-point control block. unshifted state in the button row.
Signals are assigned for each button number and you select The shift button has two operation modes.
signals by pressing the buttons. Hold mode: Mode where the shifted state is selected while
the button is pressed
For details about assigning signals, see “Creating a Lock mode: Mode where every time the button is pressed,
Cross-Point Assign Table” (page 301). it toggles between the shifted state and unshifted state
You can also disable the shift button function.
Shift button For details, see “Setting the Shift Button” (page 302).
A shift button is assigned to the rightmost button of each
cross-point button row.
46
Re-entry buttons
You can assign re-entry signals to the cross-point button Selecting a Bus
rows of the cross-point control block for use as re-entry
buttons.
Re-entry buttons are used to load an image created on one The cross-point button rows in a cross-point control block
switcher bank as an input signal on another switcher bank. are shared by multiple buses.
For example, to load the image created on M/E-1 as Buses are assigned to the cross-point button rows for use.
background B on M/E-2, press the M/E-1 re-entry button
in the cross-point button row for background B bus on
M/E-2. Operation Mode of Cross-Point
Note
Button Rows
M/E-1, M/E-2, M/E-3, and P/P re-entry signals are The operation mode of cross-point button rows in a cross-
assigned to the following cross-point buttons by default. point control block can be selected from the following
• For 24-button rows: Button numbers 20 to 23 three modes.
• For 16-button rows: Button numbers 12 to 15 They are set to key/AUX bus delegation mode by default.
Re-entry signal restrictions For details about setting the operation mode, see “Setting
The following restrictions apply when selecting a re-entry the Operation Mode of a Button Row” (page 320).
signal.
• Up to four re-entry stages are supported. Key bus mode
• Selecting a re-entry signal within the same switcher bank Uses the 1st row and 2nd row as cross-point button rows
is not supported. for the bus/utility function selected by the delegation
Extended re-entry buttons.
When extended re-entry is enabled, selection of re-entry Uses the 3rd row as a cross-point button row for
signals within the same switcher bank becomes possible. background A bus, and the 4th row for background B bus.
You can assign the following buses to the 1st row and 2nd
For details, see “Setting Extended Re-Entry” (page 308). row.
Key 1 bus to key 8 bus, utility 1 bus/2 bus, DME external
video bus, DME utility 1 bus/2 bus
Free assign mode
Uses the 1st row to 4th row as cross-point button rows for
the bus/utility function selected by the delegation buttons.
Key/AUX bus delegation mode
Uses the 1st row as a delegation button row and the 2nd
row as a cross-point button row for the bus/utility function
selected by the 1st row buttons.
Uses the 3rd row as a cross-point button row for
background A bus, and the 4th row for background B bus.
Notes
• You can also change the bus assignment using dual
background bus mode and utility bus mode.
For details, see “Dual background bus mode” (page 49)
and “Utility bus mode” (page 49).
• You can also select a utility function when a utility/
shotbox bank is assigned to a cross-point button row.
For details, see “Utility Functions” (page 177).
47
The assignable buses and assignment operation are as Bus Assignment operation
follows.
DME utility 1 bus b) • Press delegation buttons
DME utility 2 bus b) [DME UTIL1] and [DME
Notes UTIL2], turning them on. c)
• To assign to the 2nd row in
• You can assign the delegation buttons to use in key bus key/AUX bus delegation
mode and free assign mode to the function button mode, press the [DME
section. UTIL1] and [DME UTIL2]
For details, see “Assigning Control Panel Buttons” buttons in the 1st row,
(page 317). turning them on.
• In key/AUX bus delegation mode, you can assign Edit preview bus • In free assign mode, press
delegation buttons to the 1st row. delegation button [EDIT
For details, see “Setting the key/AUX bus delegation PVW], turning it on.
mode button row” (page 320). • To assign to the 2nd row in
• When using an SL key, key bus operation is disabled. key/AUX bus delegation
For details about SL keys, see “SL Key” (page 72). mode, press the [EDIT
PVW] button in the 1st row,
Bus Assignment operation turning it on.
a) b)
Background A bus • In key bus mode and key/ AUX1 bus to AUX48 bus • In free assign mode, press
AUX bus delegation mode, delegation buttons [AUX1]
assigned to the 3rd row to [AUX48], turning them
(fixed). on.
• In free assign mode, press • To assign to the 2nd row in
delegation button [A], key/AUX bus delegation
turning it on. mode, press the [AUX1] to
Background B bus a) b) • In key bus mode and key/ [AUX48] buttons in the 1st
AUX bus delegation mode, row, turning them on.
assigned to the 4th row Frame memory source 1 bus • In free assign mode, press
(fixed). Frame memory source 2 bus delegation buttons [FMS1]
• In free assign mode, press and [FMS2], turning them
delegation button [B], on.
turning it on. • To assign to the 2nd row in
Key 1 bus to key 8 bus b) • Press delegation buttons key/AUX bus delegation
[KEY1] to [KEY8], turning mode, press the [FMS1]
them on. c) and [FMS2] buttons in the
• To assign to the 2nd row in 1st row, turning them on.
key/AUX bus delegation DME1 video bus to DME4 • In free assign mode, press
mode, press the [KEY1] to video bus delegation buttons
[KEY8] buttons in the 1st [DME1V] to [DME4V],
row, turning them on. turning them on.
Utility 1 bus b) • Press delegation buttons • To assign to the 2nd row in
Utility 2 bus b) [UTIL1] and [UTIL2], key/AUX bus delegation
turning them on. c) mode, press the [DME1V]
• To assign to the 2nd row in to [DME4V] buttons in the
key/AUX bus delegation 1st row, turning them on.
mode, press the [UTIL1] DME1 key bus to DME4 key • In free assign mode, press
and [UTIL2] buttons in the bus delegation buttons
1st row, turning them on. [DME1K] to [DME4K],
DME external video bus b) • Press delegation button turning them on.
[DME EXT], turning it on. c) • To assign to the 2nd row in
• To assign to the 2nd row in key/AUX bus delegation
key/AUX bus delegation mode, press the [DME1K]
mode, press the [DME to [DME4K] buttons in the
EXT] button in the 1st row, 1st row, turning them on.
turning it on. a) Dual background bus mode can be selected.
b) Can also be assigned in utility bus mode.
c) Can be assigned to the 1st row and 2nd row in key bus mode, or to the 1st
row to 4th row in free assign mode.
48
Dual background bus mode
You can select the background A bus (3rd row) shifted- Selecting Signals
state signal in the 1st row, and the background B bus (4th
row) shifted-state signal in the 2nd row.
To set dual background bus mode, press the [DUAL
BKGD BUS] button, turning it on. Assigning Signals
Signals input to the input connectors and signals generated
Notes within the switcher can be selected using the cross-point
• The [DUAL BKGD BUS] button must be assigned to the buttons.
function button section. Each button number has assigned to it a video signal and a
For details, see “Assigning Control Panel Buttons” key signal, forming a pair.
(page 317). The signal assignment and video signal/key signal
• Dual background bus mode is not available in the combination are set in the Home > Setup > Xpt Assign >
following cases. Main, V/K Pair Assign menu (19102.21).
- In free assign mode
- When dual M/E is set For details, see “Creating a Cross-Point Assign Table”
- When the switcher bank operation mode is DSK mode (page 301).
• Utility bus mode is not available in the following cases. 1st (left side) to 1 to 23 24 to 46
23rd buttons
- In key/AUX bus delegation mode
- In free assign mode The rightmost (24th) button is used as the [SHIFT] button.
- When dual background bus mode is set When selecting the signals of button numbers 1 to 23,
• If a key bus is assigned using the [UTIL] button, the key press the corresponding number button.
source signal cannot be selected. When selecting the signals of button numbers 24 to 46,
press the [SHIFT] button, turning it on, and press the
corresponding number button.
[SHIFT] button
The [SHIFT] button has two operation modes.
49
Hold mode: Mode where the shifted state is selected while
the button is pressed Color of button Button state
when lit
Lock mode: Mode where every time the button is pressed,
it toggles between the shifted state and unshifted state Amber Low tally
You can also disable the shift button function. Selected signal is not included in the final
output image
For details, see “Setting the Shift Button” (page 302). Red High tally
Selected signal is included in the final
output image
Note
The operation mode of the [SHIFT] button is the operation Cross-point indicators
mode set by the cross-point assign table of the switcher When lit, these indicate the source color of the video signal
bank, regardless of the buses assigned to the cross-point assigned to buttons on the 3rd row of the cross-point
button rows. control block.
[SHIFT ALL] button The color of the cross-point indicators does not change
You can switch all the cross-point buttons in the 1st row to even if a 3rd row button is lit red or amber.
4th row to the shifted state using the [SHIFT ALL] button
assigned to the function button section (excluding 1st row
delegation buttons in key/AUX bus delegation mode). Cross-Point Hold
The [SHIFT ALL] button operation can be set to hold
mode or lock mode. Setting cross-point hold enables you to recall an effect
timeline or snapshot while keeping the current cross-point
Notes selection unchanged.
You can set cross-point hold for each cross-point button
• The [SHIFT ALL] button is enabled, even if the [SHIFT] row.
button use is disabled. In this case, the button numbers To set cross-point hold, press the [XPT HOLD] button for
are 1 to 24 in the unshifted state, and 25 to 48 in the the 1st row to 4th row assigned to the function button
shifted state. section, turning it on.
• The [SHIFT ALL] button is disabled in the following
cases. Key bus cross-point hold
- In [SHIFT] button hold mode For a key bus, the cross-point hold operation mode
- When dual background bus mode is set specified in the Home > Setup > Switcher > Custom >
- When dual M/E is set Key/Wipe menu (19103.43) is applied.
The following three operation modes can be set.
Key disable: Mode which maintains cross-point selection
state and key setting information
Cross-Point Button Display Key disable (including key state): Mode which maintains
cross-point selection state, key setting information,
Source name of signals and the key inserted/removed (on/off) state
Cross-point hold: Mode which maintains cross-point
You can attach a name (source name) to the signal selection state only
assigned to a cross-point button, with a maximum of 16
characters. For details, see “Setting the Cross-Point Hold Operation
The specified source name appears on the display of the Mode” (page 313).
cross-point control block. When a signal in the shifted state
of a cross-point button is selected, the source name of the Bus override
shifted-state signal is displayed. This function allows you to temporarily set cross-point
Six types of display mode can be set according to the hold for specific cross-point buttons only.
information to display. The display mode switches each It is enabled for background A bus and background B bus
time the [DISP MODE] button assigned to the function cross-point buttons only.
button section is pressed. When you press and hold a cross-point button and recall a
snapshot, the cross-point selection state is maintained for
Colors of lit cross-point buttons the pressed button only. The cross-point selection state is
In a single cross-point button row, only the last pressed maintained while the button is pressed, even when
button is active, and is lit amber or red. executing an effect timeline.
50
Selecting a key fill signal/key source signal For a key source signal
You can select a key fill signal and key source signal using The [KEY] button is enabled in operation modes that allow
the following methods. you to select both a key signal and a video signal.
To select a key fill signal For details about settings, see “Setting the operation mode
• Press a cross-point button in the cross-point button row of the [KEY] button in the cross-point control block”
assigned with the key bus. (page 326).
• In key bus mode and free assign mode, press and hold a
key bus delegation button in the function button section When the [KEY] button is pressed, turning it on, and a
and press a cross-point button in the 1st row. cross-point button is pressed, the key signal is selected.
• In key/AUX bus delegation mode, press a key bus When the [KEY] button is not lit and a cross-point button
delegation button in the 1st row and press a cross-point is pressed, the video signal is selected.
button in the 2nd row.
• On the Flexi Pad control block in key operation mode, Notes
press and hold a key delegation button in the memory
recall section and press a cross-point button in the 1st • The [KEY] button cannot be used on the following
row in the cross-point control block. buses. Only the video signal is selectable.
- Key fill bus
To select a key source signal - DME video bus
• In key bus mode and free assign mode, press and hold a - Background A bus, B bus
key bus delegation button in the function button section • For a key source signal, you can also select a video
and press a cross-point button in the 2nd row. signal/key signal in the menu.
• In key/AUX bus delegation mode, press and hold a key For details, see “Selecting the key fill/key source
bus delegation button in the 1st row and press a cross- signals” (page 79).
point button in the 2nd row.
• On the Flexi Pad control block in key operation mode,
press and hold a key delegation button in the memory
Selecting a DME video signal/DME key
recall section and press a cross-point button in the 2nd signal
row in the cross-point control block. Press a cross-point button in the cross-point button row
assigned with the DME video bus or DME key bus to
Notes select a signal.
When a cross-point button is pressed, the signal for the
• You can also select a key fill signal/key source signal in front side of the image is selected. When a cross-point
the menu. button is pressed while pressing a DME video bus/DME
For details, see “Selecting the key fill/key source key bus delegation button in the function button section,
signals” (page 79). the signal for the back side of the image is selected.
• You can also select a signal paired with a key fill signal
or select the key fill signal itself as the key source signal
Note
automatically.
For details, see “Setting a key fill/key source” A signal for the back side can be selected when separate
(page 78). sides are enabled. When separate sides are disabled, the
signals for the front and back sides are the same.
Selecting a video signal/key signal For details about setting separate sides, see “Setting
In free assign mode or key/AUX bus delegation mode, you Separate Sides” (page 159).
can select the video signal or the key signal of a V/K pair
using the [KEY] button assigned to the function button
section.
When a cross-point button is pressed while pressing the
[KEY] button, the key signal is selected. When a cross-
point button is pressed without pressing the [KEY] button,
the video signal is selected.
Information for the key signal or video signal, whichever
is selected, appears on the display on the cross-point
control block.
51
To protect a cross-point button row
Preventing Operation of Press the [PROT] button, turning it on, for the target cross-
point button row (1st row to 4th row) to set.
Cross-point Buttons To release the protection setting for a cross-point
button row
Press the [PROT] button, turning it off, for the target cross-
Preventing Operation of Cross-Point point button row (1st row to 4th row) to release.
Buttons (Inhibit Function)
For each cross-point button in the cross-point control
block, you can temporarily inhibit operations.
To enable/disable the inhibit function, use the [INHBT
SET] button and [INHBT ALL CLR] button assigned to
the function button section.
When a cross-point button is set to inhibited, the operation
of all cross-point buttons with the same number in the
cross-point button rows are inhibited.
To inhibit a cross-point button
Press and hold the [INHBT SET] button, and press the
target cross-point button to set.
While the [INHBT SET] button is pressed, the inhibited
buttons flash amber.
Notes
• When a cross-point button is inhibited, the button turns
off and the display signal name is not displayed.
• Even when you inhibit a cross-point button, macro
attachment settings are still possible.
• You can inhibit cross-point buttons for each cross-point
assign table using the Home > Setup > Xpt Assign >
Table Button Assign menu (19102.31).
For details about setting inhibit mode, see “Creating
Tables 1 to 14” (page 301).
To release the inhibit setting for a cross-point
button
Press and hold the [INHBT SET] button, and press the
target cross-point button to release.
To release the inhibit setting for all cross-point
buttons
Press and hold the [INHBT SET] button, and press the
[INHBT ALL CLR] button.
52
Transitions Chapter 5
background always switches from background A to
Overview background B. When the transition completes, the cross-
points of the background A bus and background B bus
interchange.
In bus fixed mode, depending on the transition, the cross-
Switching from the current image to a new image is
points of the background A bus and background B bus do
referred to as a transition.
not interchange.
Switching a background image or key insertion/removal
can be performed, depending on the transition.
For details, see “Flip-flop mode and bus fixed mode”
The method for switching images (transition type) can be
(page 62).
set, and the transition executed using the buttons and fader
lever on the control panel.
Inserting and removing a key
Independent key transition
In addition to common transitions, it is possible to To insert/remove a key in a transition, select a key for a
configure independent transitions for each key. next transition.
Executing an independent key transition in combination When a key that is not inserted in the current background
with a common transition enables different transition types image is selected, depending on the transition, the key is
to be used for the background and keys. inserted.
When a key that is inserted is selected, depending on the
transition, the key is removed.
Transition operation flow You can also simultaneously insert and remove keys when
switching the background.
Select the current background You can also change the key overlay sequence (key
r priority), depending on the transition.
Select a next transition (see page 55)
Background Key
r r
Select a new background Set keys
r r
Select and set a transition type (see page 58)
r
Preview transition (see page 65)
r
Execute transition (see page 61)
53
Transition type
You can set the way in which the transition occurs. Basic Operation for
You can select the following transition types.
Transitions
Transition type Description
Mix The new image progressively
fades in over the current image. The basic transition operation flow is as follows.
The sum of the two image outputs
is maintained constant, and the
output of each is at 50% at the
1 Select a background image using the background A
mid-point of the transition. bus cross-point buttons in the cross-point control
block.
NAM (non-additive The current image and new image
mix) are compared, and the image with
the higher luminance level is given 2 Select the switch target of a transition.
priority in the output. The output of
each is at 100% at the mid-point of Select a next transition using the next transition
the transition. selection buttons in the transition control block.
Super mix The current image output is held at For details about next transitions, see “Next
100%, and is mixed with the new Transitions” (page 55).
image. The output at the mid-point
of the transition can be 0% to
100%. 3 Set the state for after the transition executes.
Preset color mix A color matte (plain image) is When switching the background, select a background
inserted during the transition, image using the background B bus cross-point buttons.
where the current image is
switched to the new image in a For details about selecting a signal, see “Chapter 4
two-stage transition. Selecting Signals” (page 46).
Wipe The current image switches to the
new image using a wipe pattern. When inserting a key, set the key to insert.
DME wipe The current image switches to the For details about setting keys, see “Chapter 6 Keys”
new image using a DME wipe (page 71).
pattern.
Clip transition Plays back frame memory video When changing the key overlay sequence, set the key
content linked to a mix or wipe priority.
transition.
For details about key priority, see “Key Priority”
Cut The current image switches (page 56).
instantaneously to the new image.
4 Select a transition type.
Select a transition type using the transition type
selection buttons in the transition control block.
To switch (cut) from the current image instantaneously
to the new image, proceed to step 6.
For details about transition types, see “Transition
Type” (page 58).
54
For details about transition preview, see “Transition
Preview” (page 65).
Next Transitions
When a wipe or DME wipe is selected as the transition
type, you can set the transition execution range
(pattern limit). You can select the switch target of a transition.
Next transitions are configured using the transition control
For details about pattern limits, see “Pattern Limit” block.
(page 63).
6 Execute a transition.
Selecting a Next Transition
Execute the transition using the buttons and fader lever
in the transition execution section on the transition You can select a next transition using the transition control
control block. block of the target switcher bank.
For details about executing transitions, see
“Executing a Transition” (page 61). Note
The buttons used for configuring a next transition must be
assigned to the transition settings section of the transition
control block beforehand.
To insert/remove a key
Press a [KEY1] to [KEY8] button, turning it on.
If a key is not inserted, it will be inserted. If a key is
inserted, it will be removed.
When inserting a key, set the key to insert.
Note
Double-pressing of the [BKGD] button must first be
enabled.
55
To change the key overlay sequence
Press the [KEY PRIOR] button.
Set the key priority for after the transition.
Key Priority
For details about key priority, see “Key Priority”
When multiple keys are inserted, you can set the overlay
(page 56).
sequence of the keys.
When the [KEY PRIOR] button is selected in a next
To select multiple preconfigured next transitions
transition, depending on the transition, the key overlay
simultaneously
sequence changes.
Press the [ALL] button.
The key overlay sequence is set by key priority values 1 to
8, numbered from the front to the rear.
For details about setting next transitions selected
The key priority can be set using the transition control
simultaneously, see “Setting the next transitions to select
block or the menu.
using the [ALL] button in the transition control block”
(page 325).
Notes
• When the operation mode of the switcher bank is set to
multi program mode or multi program 2 mode, the key
priority cannot be changed, depending on the transition.
• The key priority cannot be configured in fixed mode.
For details, see “Setting the Key Priority Mode”
(page 313).
• The current key overlay sequence can be checked on the
program output of the switcher bank.
When the [KEY PRIOR] button is selected in a next
transition, the key overlay sequence for after the
transition can be checked on the preview output of the
switcher bank.
Key priority of SL keys
SL keys 5 to 8 are assigned the priority of four keys as a
single group.
Within SL keys 5 to 8, you can set any priority.
Example:
Overlay keys in the sequence key 1, key 2, SL keys 5 to 8,
key 3, key 4
Set the priority as follows.
Priority 1: Key 1
Priority 2: Key 2
Priority 3 to 6: SL keys 5 to 8 (priority 3 to 6 can be
assigned arbitrarily within SL keys 5 to 8)
Priority 7: Key 3
Priority 8: Key 4
Note
To use the SL key function, the XKS-G1600 GPU Pack
(option) and XZS-G1620 SL Key License (option) are
required.
When the system signal format is 2160P, the SL key
function must be enabled for use.
56
Setting the key priority (menu)
Setting Key Priority
This section describes the M/E-1 menu as an example.
Setting the key priority (transition control 1 Open the Home > M/E-1 > Common > Key Priority/
block) Key Assign menu (11110.11).
You can set the key priority using the transition control
block of the target switcher bank.
2 Select the target key priority (current key priority or
key priority for after the transition) to set.
Note When setting the current key priority
Press the [Edit] button for [Current Key Priority]. The
The buttons used for configuring the key priority must be
[Current Key Priority] window appears.
assigned to the transition settings section of the transition
control block beforehand. When setting the key priority for after the
transition
For details about assigning buttons, see “Assigning Press the [Edit] button for [Next Key Priority]. The
Control Panel Buttons” (page 317). [Next Key Priority] window appears.
1 Press and hold the [PRIOR SET] and press the [KEY 3 Set the buttons for the keys to set to priority 1 to 8 to
PRIOR] button to select the target key priority (current the on state in [Priority 1] to [Priority 8].
key priority or key priority for after the transition) to
set. Note
When the [KEY PRIOR] button is lit green, the key The priority options available for selection vary
priority setting for after the transition is selected. depending on the number of keys assigned to a
When the [KEY PRIOR] button is not lit, the current switcher bank.
key priority setting is selected.
4 Press [OK].
2 Set the key to display at the front.
Press and hold the [PRIOR SET] button and press a Checking the key priority settings
[KEY1] to [KEY8] button. When the key priority is set using the transition control
The selected key is set to be frontmost (priority 1). block, the key status and priority are shown on the display.
To set the key priority for after the transition to the
same setting as the current setting, press and hold the Key status display
[PRIOR SET] button and press the [BKGD] button. When a key is inserted, [K1] to [K8] are displayed
inverted.
Note
Key priority display
The [BKGD] button is enabled only when in the mode The numbers 1 to 8 (priority 1 to 8) are displayed under the
for changing the key priority for after the transition. status indicators for each key.
If the [KEY PRIOR] button is selected in a next transition,
3 Repeat steps 1 and 2 to set the key priority, as the priority (1 to 8) of keys for after the transition are
required. displayed inverted on the right of the current priority. The
key priority for after the transition is not displayed if the
values are the same as the current priority setting.
57
For details, see “Setting Super Mix” (page 59).
Transition Type When preset color mix is selected
Set the color matte to insert during the transition.
You can set the way in which the transition occurs. For details, see “Setting a Preset Color Mix”
The transition type is configured using the transition (page 59).
control block or the menu. When a wipe is selected
Set the wipe pattern.
For details about transition types, see “Transition type”
(page 54). For details, see “Setting a Wipe” (page 99).
When a DME wipe is selected
Set the DME wipe pattern.
Setting a Transition Type For details, see “Setting a DME Wipe” (page 115).
When a clip transition is selected
Setting a transition type (transition control Set the clip transition.
block)
For details, see “Setting a Clip Transition”
You can select a transition type using the transition control (page 123).
block of the target switcher bank.
Notes
Setting the key transition type (menu)
This section describes the M/E-1 menu as an example.
• The buttons used for configuring the transition type must
be assigned to the transition settings section of the 1 Open the Home > M/E-1 > Bus/Transition >
transition control block beforehand. Transition > Transition Type menu (11109.21).
For details about assigning buttons, see “Assigning
Control Panel Buttons” (page 317). 2 Select a transition type in the [Transition Type] group.
• When the operation mode of the switcher bank is set to
multi program mode or multi program 2 mode, preset Mix: Mix
color mix cannot be used when selecting a key for a next NAM: Non-additive mix
transition. Super Mix: Super mix
• When the operation mode of the switcher bank is set to Preset Color Mix: Preset color mix
multi program mode or multi program 2 mode, there Wipe: Wipe
may be cases in which two or more transition type DME Wipe: DME wipe
selection buttons are lit. FM 1&2 Clip to FM 15&16 Clip: Clip transition
1 Select a transition type using the transition type 3 Set the transition type.
selection buttons.
Make the required settings for the selected transition
Press the [MIX] button, [NAM] button, [SUPER MIX] type.
button, [PST COLOR MIX] button, [WIPE] button,
[DME WIPE] button, or a [FM1&2 CLIP] to When a mix, non-additive mix, super mix, preset
[FM15&16 CLIP] button, turning it on. color mix, wipe, or DME wipe is selected
Set the transition rate.
2 Set the transition type. For details about the transition rate, see “Transition
Rate” (page 60).
Make the required settings for the selected transition
type. When super mix is selected
Set the output level at the mid-point of the transition.
When a mix, non-additive mix, super mix, preset
color mix, wipe, or DME wipe is selected For details, see “Setting Super Mix” (page 59).
Set the transition rate.
When preset color mix is selected
For details about the transition rate, see “Transition Set the color matte to insert during the transition.
Rate” (page 60).
For details, see “Setting a Preset Color Mix”
When super mix is selected (page 59).
Set the output level at the mid-point of the transition.
58
When a wipe is selected One-time mode:
Set the wipe pattern. Return to the previous transition type when the preset
For details, see “Setting a Wipe” (page 99). color mix transition is completed.
Non-drop key:
When a DME wipe is selected If a key is inserted in the current image, it is removed
Set the DME wipe pattern. by the color matte during the transition, and the key
status for after the transition is applied to the new
For details, see “Setting a DME Wipe” (page 115).
image. You can set a mode that the selected key is not
When a clip transition is selected removed by the color matte.
Set the clip transition.
For details, see “Setting a Clip Transition”
1 Open the Home > M/E-1 > Bus/Transition >
Transition > Transition Type menu (11109.21).
(page 123).
2 Set the [Preset Color Mix] button in the [Transition
Type] group to the on state.
Setting Super Mix
3 Select an image to insert in the [Preset Color Mix Fill]
Set the output levels of the current image and new image group.
at the mid-point of the transition. You can set a value in the
range 0% to 100%. Utility 2 Bus: Utility 2 bus signal
This section describes the M/E-1 menu as an example. For details about selecting a signal, see “Chapter 4
Selecting Signals” (page 46).
1 Open the Home > M/E-1 > Bus/Transition >
Transition > Transition Type menu (11109.21). Flat Color: Color matte
When the [Flat Color] button is selected, set the
2 Set the [Super Mix] button in the [Transition Type] following parameters.
group to the on state and set the following parameters.
No. Parameter Adjustment
2 Luminance Luminance
No. Parameter Adjustment
3 Saturation Saturation
2 A Gain Background A output level
4 Hue Hue
3 B Gain Background B output level
Stroke mode:
In a preset color mix, the current image switches to the
color matte on the 1st stroke, and then switches from
the color matte to the new image on the 2nd stroke
(normal mode).
You can also set a preset color mix so that it executes
in one stroke (single mode).
Note
In bus fixed mode, single mode is selected.
59
Setting the transition rate (Flexi Pad
Transition Rate control block)
You can set the transition rate using the Flexi Pad control
block of the target switcher bank.
You can set the time taken from the beginning of a
transition to its completion. 1 Press the [TRANS RATE] button.
The transition rate is configured using the Flexi Pad
control block or the menu. The memory recall section switches to transition rate
operation mode.
Note
2 Enter a transition rate using the number input buttons.
When a clip transition is selected as the transition type, it
is not possible to set the transition rate. You can switch the input mode using the [TC] button.
In frame number input mode, enter three digits. In
timecode input mode, enter four digits.
The entered value appears in the top right button of the
Transition Rate Input/Display Mode memory recall section.
Transition rate input mode To delete the entered value
When entering the transition rate, you can select either Press the [CLEAR] button.
frame number input or timecode input.
3 Press the [ENTER] button.
For details, see “Timecode input and frame number input”
(page 43).
Setting the transition rate (menu)
Frame number input: This section describes the M/E-1 menu as an example.
Enter a number in the range 0 to 999 frames.
Timecode input: 1 Open the Home > M/E-1 > Bus/Transition >
Enter a value converted to frames of up to 999 frames. Transition > Transition Type menu (11109.21).
Transition rate display mode 2 Select a transition type in the [Transition Type] group.
You can set the transition rate display mode to frame
number display or timecode display. 3 Set the transition rate using the following parameter.
The display mode settings are common to all switcher
banks.
No. Parameter Adjustment
For details, see “Setting the transition rate display” 1 Transition Rate Transition rate
(page 324).
To set the transition rate in list view
Frame number display: You can set the transition rate in transition rate list view on
Displays the number of frames (0 to 999). Values each switcher bank.
entered in timecode input mode are converted to the
number of frames for display. 1 Open the Home > Utility > Transition Rate menu
Timecode display: (18201.21).
Displays a “ss:ff” timecode value (second:frame). The transition rate for common transitions and
Values entered in frame input mode are converted to a independent key transitions is displayed for each
timecode for display. switcher bank.
60
Auto Transitions
Executing a Transition
To switch images with the preset transition type
and transition rate
Transitions are executed using the transition control block. Press the [AUTO TRANS] button in the transition control
You can also execute auto transitions using the menu. block.
The transition is executed automatically with the preset
speed (transition rate).
Transition indicator
During the transition execution, the [AUTO TRANS]
Fader lever button is lit amber.
To switch images instantaneously
Press the [CUT] button in the transition control block.
When the next transition is a key, the key is inserted or
removed instantaneously.
To complete a partially executed transition
instantaneously
Press the [CUT] button.
The [AUTO TRANS] button turns off.
61
Changing from manual transition to auto
transition Fader lever
Non-sync
If the fader lever is stopped in an intermediate position and
an auto transition is executed, then the fader lever position Flip-flop mode
will not match the current position of the transition when
the transition is completed. This is termed non-sync state.
You can check for non-sync state by whether the top and
bottom LEDs of the transition indicator are lit or flashing.
62
Notes
Notes
• When the operation mode of the switcher bank is set to
multi program mode, pattern limits can be set only when
the background transition type is a wipe or DME wipe.
If a key is selected for a next transition, the pattern limit
settings are reflected in the wipe or DME wipe selected
for the background transition type.
• The buttons used for configuring and executing pattern
limits must be assigned to the transition settings section
of the transition control block beforehand.
For details about assigning buttons, see “Assigning
Control Panel Buttons” (page 317).
To set a pattern limit while checking a transition
preview
Press the [TRANS PVW] button in the transition control
block, turning it on.
You can adjust the pattern limit while checking the
transition status on a monitor set with the preview output.
Note
Check that the [PTN LIMIT] button is off.
63
1 Move the fader lever to the position corresponding to For details about setting the operation mode, see “Setting
the desired pattern size. the Operation Mode When the Pattern Limit is Released”
(page 314).
2 Press the [LIMIT SET] button.
1 Press the [PTN LIMIT] button in the transition control
This sets the current fader lever position as the pattern block.
limit.
The [PTN LIMIT] button is lit green.
Setting a pattern limit (menu) 2 Execute a transition.
This section describes the M/E-1 menu as an example.
If the operation mode when a pattern limit is
1 Open the pattern limit setting menu. released is set to auto
Press the [PTN LIMIT] button to execute the
When the transition type is a wipe, open the Home > remainder of the transition automatically with the
M/E-1 > Bus/Transition > Wipe > Pattern Mix/Edge/ preset transition rate. When the transition is
Direction menu (11109.33). completed, the pattern limit is released and the [PTN
When the transition type is a DME wipe, open the LIMIT] button turns off.
Home > M/E-1 > Bus/Transition > DME Wipe >
Edge/Direction menu (11109.44). If the operation mode when a pattern limit is
released is set to manual
2 Set the [Pattern Limit] button to the on state and set the Execute the remainder of the transition using one of
following parameter. the following methods. When the transition is
completed, the [PTN LIMIT] button turns off.
• Press the [CUT] button.
No. Parameter Adjustment
The image switches instantaneously and the pattern
1 Pattern Limit Pattern limit range (0.00% to limit is released.
100.00%) • Press the [AUTO TRANS] button.
The remainder of the transition is executed with the
preset transition rate and the pattern limit is released
Executing a Pattern Limit when execution is completed.
• Operate the fader lever.
1 Press the [PTN LIMIT] button in the transition control If the fader lever is moved in the execution direction
block, turning it on. of the transition, the remainder of the transition is
executed and the pattern limit is released when
The [PTN LIMIT] button is lit amber. execution is completed.
If the fader lever is moved in the opposite direction,
2 Execute a transition. the transition is executed such that the state before
executing the transition is restored, and the pattern
The transition progresses as far as the set pattern limit.
limit is released when execution is completed.
3 Execute the transition once again. To set the transition rate when the pattern limit is
released
The state existing before executing the transition is
This section describes the M/E-1 menu as an example.
restored.
1 Open the pattern limit setting menu.
Releasing a pattern limit
When the transition type is a wipe, open the Home >
When the state existing before executing the transition is M/E-1 > Bus/Transition > Wipe > Pattern Mix/Edge/
restored by performing step 3, press the [PTN LIMIT] Direction menu (11109.33).
button to release a pattern limit, turning the [PTN LIMIT] When the transition type is a DME wipe, open the
button off. Home > M/E-1 > Bus/Transition > DME Wipe >
To release a pattern limit in pattern limit state, execute a Edge/Direction menu (11109.44).
transition using the following procedure.
You can set the operation mode for executing a transition 2 Set the transition rate in the [Pattern Limit Release]
when releasing a pattern limit to manual or auto. group.
Auto Trans Rate: Follow the current transition rate.
64
Independ Trans Rate: Set an independent transition
rate for releasing a pattern limit.
When the [Independ Trans Rate] button is selected, set
Transition Preview
the following parameter.
No. Parameter Adjustment In transition preview mode, the status during a transition is
output on the preview output of the switcher bank.
1 Transition Rate Transition rate when the
pattern limit is released
You can check the change in the image due to a transition
in advance using a monitor configured for the preview
output.
Notes
• It is not possible to carry out a transition preview in the
following cases.
- Transition in progress
- When bus fixed mode is set
- When the switcher bank operation mode is not
standard mode
• The buttons used for configuring and executing the
transition preview must be assigned to the transition
settings section of the transition control block
beforehand.
For details about assigning buttons, see “Assigning
Control Panel Buttons” (page 317).
65
The current program output is displayed on the
preview output monitor.
Independent Key
2 Execute a transition. Transitions
The status during the transition is displayed on the
preview output monitor allowing you to check the
changes to the image. Overview
In addition to common transitions, you can configure
independent transitions for each key.
When an operation mode that supports configuration of
transitions where keys are inserted/removed independently
is set, the transition type and transition rate for inserting
and removing keys can be set separately.
66
When the common transition and independent
key transition are executed at offset times Setting the Independent Key
If a key is inserted: Transition Type
The key is removed in both transition types at offset
times. When the common transition ends, both You can set the way in which the independent key
transitions are completed even if the independent key transition occurs.
transition is in progress. The independent key transition type is configured using
If a key is not inserted: the Flexi Pad control block or the menu.
The key is inserted in the transition of the first
executed transition type. Subsequently, the key is then Note
inserted, so that when the transition with the other
transition type is executed the key will be removed. When an operation mode that supports configuration of
The transition is completed at the point when the key transitions where keys are inserted/removed independently
is removed. is set, the transition type for inserting and removing keys
can be set separately.
Make the required settings for the selected transition Press a [KEY1] to [KEY8] button, turning it on.
type.
• Transition rate settings (see page 68) 3 Select a transition type.
• Wipe settings (see page 108) Press the [MIX] button, [WIPE] button, or [DME
• DME wipe settings (see page 120) WIPE] button, turning it on.
Using transition preview mode, you can check the
status of the transition. 4 Set the transition type.
For details about transition preview, see “Transition
Preview” (page 65). Make the required settings for the selected transition
type.
3 Execute the independent key transition. When a mix, wipe, or DME wipe is selected
Execute the transition using the buttons in the Set the transition rate.
independent key transition execution section on the For details about the transition rate, see “Setting the
transition control block. Independent Key Transition Rate” (page 68).
For details about executing transitions, see When a wipe is selected
“Executing an Independent Key Transition” Set the wipe pattern.
(page 69).
For details, see “Setting an Independent Key
Transition Wipe” (page 108).
When a DME wipe is selected
Set the DME wipe pattern.
For details, see “Setting an Independent Key
Transition DME Wipe” (page 120).
67
Setting the independent key transition For details about independent key transition operation
type (menu) mode, see “Setting the Independent Key Transition Mode”
(page 311).
This section describes the M/E-1 key 1 menu as an
example. This section describes the M/E-1 key 1 menu as an
example.
1 Open the Home > M/E-1 > Key1 > Transition >
Transition Type menu (11101.51). 1 Open the Home > M/E-1 > Key1 > Transition >
Transition Type menu (11101.51).
2 Select a transition type in the [Transition Type] group.
Mix: Mix 2 Select a transition type in the [Transition Type] group.
Wipe: Wipe When an operation mode that supports configuration
DME Wipe: DME wipe of transitions where keys are inserted/removed
Cut: Cut independently is set, select a transition type for key
When an operation mode that supports configuration insertion in the [ON Transition Type] group and a
of transitions where keys are inserted/removed transition type for key removal in the [OFF Transition
independently is set, select a transition type for key Type] group.
insertion in the [ON Transition Type] group and a
transition type for key removal in the [OFF Transition 3 Set the transition rate using the following parameter.
Type] group.
When a DME wipe is selected The transition rate for common transitions and
Set the DME wipe pattern. independent key transitions is displayed for each
switcher bank.
For details, see “Setting an Independent Key
Transition DME Wipe” (page 120). 2 Select the target switcher bank to set.
68
Executing an Independent Key Notes
Transition • You can change this so that during the execution of the
transition, the button is lit green and when the transition
The independent key transition is configured using the is completed it is lit red if on-air or lit amber if not on-air.
transition control block or the menu. For details about settings, see “Setting the independent
key transition, auto transition execution button display”
Note (page 324).
• When a cut is selected as the transition type, the key is
In an independent key transition, the pattern limit function inserted/removed instantaneously.
is not available.
Executing an independent key transition
Executing an independent key transition (menu)
(transition control block)
This section describes the M/E-1 key 1 menu as an
example.
Independent key transition execution section
1 Open the Home > M/E-1 > Key1 > Key Snapshot
menu (11101.71).
2 Execute a transition.
To insert/remove a key instantaneously
Press the [KEY ON] button.
To insert/remove a key with the preset transition
type and transition rate
Press the [KEY TRANS] button.
Note
When a cut is selected as the transition type, the key is
inserted/removed instantaneously.
Note
69
1 Press the [UTIL/SBOX] button in the utility control
Fade-to-Black block.
The memory recall section switches to utility/shotbox
operation mode.
This function gradually darkens the image and changes the
P/P program output image to black. 2 Select a bank.
Setting Fade-to-Black
1 Open the Home > P/P > Bus/Transition > Transition >
Transition Type menu (11909.21).
Executing Fade-to-Black
This section describes operation using a memory recall
button ([FTB] button) in the utility control block assigned
with the “Fade To Black” utility command.
70
Keys
Key Type
Chapter 6
Overview
The key type sets the manner in which the key source is
used to cut out the background.
A key is a function in which a part of the background You can select the following key types.
image is replaced by inserting an image or superimposed
text. Key type Description
The signal used to cut out a portion of the background Luminance key The background is cut out according to
image (key source), signal to embed in the cutout portion the luminance signal of the key source,
(key fill), and key source processing method (key type) can and at the same time the key fill is also
cut out by the key source and then added
be selected for a key.
to the background.
The number of keys that can be used on each switcher bank
is four when the system signal format is 2160P, and eight Linear key This is a type of luminance key, with a
reduced variability in gain allowing more
when the system signal format is 1080P or 1080i. precise adjustment.
Chroma key A key signal based on a particular color is
Note used to cut out the background, and the
key fill is then inserted.
When M/E split is enabled, the number of keys that can be
used will vary depending on the settings. Key wipe pattern A wipe pattern of an independent key
key transition is used to cut out the
background, and the key fill is then
For details, see “Setting Sub Block keys” (page 306). inserted.
Clean mode
Key Fill and Key Source
In a luminance key or linear key, you can enable clean
The key fill signal can be set to a key bus signal or color mode.
matte. When clean mode is enabled, key fill is added to the
The key source signal can be selected using the following background without cutting out by the key source.
three modes.
Self mode: Use the same signal as the key fill signal. Note
Auto Select mode: Use the signal assigned as a pair with
the key fill bus signal on the cross-points. When clean mode is enabled, for the parts of the key fill
Split mode: Select and use a different signal than the key that are not black (excluding the part that is inserted), color
fill bus pair signal. is added to the background.
71
Zabton
Key Modifiers
Inserts a translucent pattern to the key background. You
can adjust the pattern size, color, and other parameters.
Edge type
Adds borders and other modifiers to the edge to a key. Mask
Edge type Description A mask allows a part of the image to be replaced by the
background or a key. You can correct an image, such as
Normal State with no modifiers added.
unwanted holes that appear in the background or when a
Border Adds a border around the key. key is not the desired shape, using masks.
You can adjust the border width and
density.
Two masks (main mask and sub mask) can be used on each
key.
Drop border Adds a border to the bottom and right There are two types of masks.
edges of the key.
You can adjust the border width, position, Key mask: This masks out a part of the key so that the
and density. background becomes visible.
Shadow Adds a shadow to the bottom and right
Background mask: This masks out a part of the
edges of the key. background so that the key fill becomes visible.
You can adjust the shadow width,
position, and density.
Outline Adds the outline to the key. Key Memory
You can adjust the outline width and
density.
This function allows the key settings data on each cross-
Emboss Adds an embossing effect around the point button to be automatically stored, so that when the
key. same cross-point button number is selected the settings
You can adjust the emboss width,
position, and density. data are recalled.
There are two adjustment modes, depending on the
settings data being stored.
Edge fill Simple mode: Key type, clean mode (including chroma
A signal inserted in the edge areas is called an edge fill. key plane function), key position, key invert, key
In a border, drop border, or shadow, a color matte or a adjustments (excluding color cancel, window, Y
signal selected on the utility 1 bus can be set as the edge balance, shadow, foreground color correction of a
fill. chroma key) settings are stored.
Full mode: All settings, excluding transitions, are stored.
Notes
For details about setting key memory mode, see “Setting
• In an outline, the key fill signal selected by the key fills the Key Memory Mode” (page 313).
the outline, and the background signal fills the rest of the
image.
• In an emboss, color matte 1 signal and color matte 2 Resizer
signal are used for the embossing.
A resizer is used to set a two-dimensional transform
Key drop (move, enlarge/reduce, rotate) or border/crop on a key.
It can also add effects to a key.
You can lower the key fill/key source position.
Key drop on mode: The key fill/key source position moves
downward by eight lines or four lines.
In key drop on mode for a drop border or shadow, it is SL Key
possible to add a border to the top edge of the key.
Key drop off mode: The key fill/key source position does An SL key is a software key that uses a GPU to reproduce
not move. the same functions as a hardware key.
If the number of keys on a single switcher bank is four or
Frame delay mode lower, SL keys are set as key 5 to key 8.
When frame delay mode is enabled, key drop is set to key Only one switcher bank can use an SL key.
drop off mode (fixed). In an SL key, there are restrictions on the functions and
settings that can be used.
72
For details about SL key restrictions, see “SL Key
Restrictions” (page 375).
Key Type
To use the SL key function, the following options are
required.
The key type sets the manner in which the key source is
• XKS-G1600 GPU Pack
used to cut out the background.
• XZS-G1620 SL Key License
The key type is configured using the menu.
When the system signal format is 2160P, the SL key
This section describes the M/E-1 key 1 menu as an
function must be enabled for use.
example.
For details about setting GPU functions, see “Setting a
For details about key types, see “Key Type” (page 71).
GPU” (page 286).
a) No filter is applied when set to “1”. The larger the value, the stronger
the filtering applied.
73
To set the wipe pattern for a key wipe pattern key
Press the [Pattern Select] button and open the Home > No. Parameter Adjustment
M/E-1 > Key1 > Transition > Wipe menu (11101.52). 1 H Phase Simultaneous adjustment of
Select a pattern and set modifiers. position of key left and right
edges
For details, see “Setting an Independent Key Transition 2 Left Position of key left edge
Wipe” (page 108). 3 Right Position of key right edge
Note
1 Open the Home > M/E-1 > Key1 > Type > Type Select
menu (11101.11).
1 Open the Home > M/E-1 > Key1 > Type > Type Select
menu (11101.11).
1 Open the Home > M/E-1 > Key1 > Type > Type Select
menu (11101.11).
2 Set the [Key Position] button to the on state and set the
following parameters.
74
Setting a Chroma Key
Chroma Key
Composing an image by chroma keying
When chroma key is selected as the key type, you can
configure and adjust the chroma key. 1 Open the Home > M/E-1 > Key1 > Type > Chroma
This section describes the M/E-1 key 1 menu as an Adjust menu (11101.12).
example.
2 Execute an auto chroma key.
Adjust the chroma key manually as required.
Overview
For details, see “Chroma Key Adjustments”
A key signal based on a particular color is used to cut out (page 75).
the background, and a key fill is then inserted to create an
image. 3 In the [Mix Mode] group, select a chroma key
In an image created using a chroma key, the image at the composition method.
rear is called the background and the inserted image is
Normal Mix: Normal mix
called the foreground.
Additive Mix: Additive mix
Two mixing methods, normal mix and additive mix, are
available.
Setting the plane function
Normal mix
The background which is cut out by a key signal is mixed
with the foreground which is cut out by the key signal. Note
For details about color canceling, see “Adjusting color No. Parameter Adjustment
cancel” (page 77). 1 Luminance Luminance
Plane function To disable the plane function, set the [Plane] button to
In an additive mix, since the background is mixed with the the off state.
unchanged foreground, an uneven blue background may
appear in the composed image.
You can specify a specific luminance level and remove Chroma Key Adjustments
parts of the blue background with lower luminance to
avoid this unevenness. Automatic adjustment using an auto chroma key and
separate manual adjustment of required processing can be
Auto chroma key
performed.
You can specify a specific color of the foreground that
automatically generates a chroma key. Auto chroma key
Immediately after an auto chroma key is executed, manual You can specify a specific color (blue background, for
fine tuning is effective, if required. example) of the foreground to automatically generate a
The following settings can be adjusted manually. chroma key.
• Key active
• Color cancel Key active
• Window When the key active function is enabled, the composite
• Y balance image is output to a monitor, and you can adjust the
• Shadow composition while viewing the monitor.
• Foreground color correction
75
When the key active function is disabled, only the and therefore it is possible to combine colors which are the
foreground image is output, and you can make color cancel same color as the background (blue background, for
adjustments while viewing the monitor. example) in the foreground.
Color cancel Shadow
If the background color is leaking into the foreground When the shadow function is enabled, the shadow of the
image, enabling the color cancel function allows you to subject projected on the background (blue background, for
eliminate this leakage. example) from the foreground appears more natural. Since
the parts of the blue background darker than a specified
Window intensity are treated as shadows, there is no effect on
When the window function is enabled, you can adjust the cutting out of the foreground.
detection range used to create the key signal.
When the window function is disabled, the default range is Foreground color correction
used for image adjustment. You can adjust the hue of the foreground and the gain of
A chroma key generates a key signal based on a specific the video signal/luminance signal/chrominance signal.
color (blue background, for example) of the foreground. In
the window function, you can specify a range of colors
around a reference color to create a key.
Executing an auto chroma key
The region that makes up the key signal in the foreground You can execute an auto chroma key based on the color
(to be replaced by the background) appears as a fan shape specified by a sample mark.
with a cropped vertex when viewed on a vectorscope. This
region is specified by two parameters: an [Angle] Note
parameter (opening angle) and a [Crop] parameter (degree
of vertex cropping). When using a sample mark for other keys, the sample mark
cannot be enabled.
1 Open the Home > M/E-1 > Key1 > Type > Chroma
Adjust menu (11101.12).
76
No. Parameter Adjustment Adjusting color cancel
5 Filter Filter (1 to 9) a)
1 Open the Home > M/E-1 > Key1 > Type > Chroma
a) No filter is applied when set to “1”. The larger the value, the stronger Adjust menu (11101.12).
the filtering applied.
1 Open the Home > M/E-1 > Key1 > Type > Chroma No. Parameter Adjustment
Adjust menu (11101.12).
1 Luminance Luminance
2 Set the [Window] button to the on state and set the 2 Saturation Saturation
following parameters. 3 Hue Hue
5 Filter Filter (1 to 9) a)
No. Parameter Adjustment
a) No filter is applied when set to “1”. The larger the value, the stronger
1 Crop Vertex crop level the filtering applied.
2 Angle Opening angle To adjust the color cancel key
Set the key signal for color cancel.
Adjusting the Y balance
1 Set the [Cancel Key] button in the [Color Cancel]
1 Open the Home > M/E-1 > Key1 > Type > Chroma group to the on state and set the following parameters.
Adjust menu (11101.12).
No. Parameter Adjustment
2 Set the [Y Balance] button to the on state and set the 1 Clip Reference level for key signal
following parameters. generation
2 Gain Key gain
No. Parameter Adjustment
1 Clip Reference level for key signal 2 Set the [Key Position] button in the [Color Cancel]
generation group to the on state and set the following parameters.
2 Gain Key gain Adjust the position of the color cancel key.
3 Luminance Key luminance
No. Parameter Adjustment
1 H Phase Simultaneous adjustment of
Adjusting the shadow position of left and right edges
2 Left Position of left edge
Note
3 Right Position of right edge
When the system signal format is 2160P, the shadow
function cannot be set. 3 Set the [Window] button in the [Color Cancel] group
to the on state and set the following parameters.
1 Open the Home > M/E-1 > Key1 > Type > Chroma
Adjust menu (11101.12). Adjust the detection range of the color cancel key.
77
Adjusting the foreground color correction
1 Open the Home > M/E-1 > Key1 > Type > Chroma
Key Fill and Key Source
Adjust menu (11101.12).
2 Set the [FRGD CCR] button to the on state and set the Selecting Signals
following parameters.
Set the signals to insert in the key fill and key source.
This section describes the M/E-1 key 1 menu as an
No. Parameter Adjustment
example.
1 Video Gain Video signal gain
2 Y Gain Luminance signal gain
Setting a key fill/key source
3 C Gain Chrominance signal gain
4 Hue Hue offset amount 1 Open the Home > M/E-1 > Key1 > Type > Type Select
menu (11101.11).
1 Open the Home > M/E-1 > Key1 > Type > Matte
Adjust menu (11101.13).
78
2 Set the [Mix Color] button in the [Fill Matte] group to To swap color 1 and color 2 in a color mix
the on state and set the following parameters. Set the [Color Invert] button to the on state.
To set modifiers for a color mix pattern
No. Parameter Adjustment You can press the [Pattern Adjust] button and set the
1 Size Pattern size following modifiers from the displayed menu.
2 Soft Softness of the pattern contour When the [Key Wipe] button is selected in the [Mix
Pattern] group, the Home > M/E-1 > Key1 > Transition >
To set a single color, set the [Flat Color] button to the Wipe menu (11101.52) is recalled.
on state. When the [Key Edge Pattern] button is selected in the [Mix
Pattern] group, the Home > M/E-1 > Key1 > Edge > Matte
Note Adjust menu (11101.22) is recalled.
Position:
The [Flat Color] button parameters are shared with the Set the [Position] button to the on state and set the
[Matte] button parameters in the [Key Fill] group in parameters.
the Home > M/E-1 > Key1 > Type > Type Select menu
(11101.11). For details about setting parameters, see “Setting the
wipe pattern position (Position)” (page 108).
3 In the [Mix Pattern] group, select a mix pattern for the Multiplication:
color mix. Set the [Multi] button to the on state and set the
Key Wipe: Use a wipe pattern selected for an parameters.
independent key transition. For details about setting parameters, see “Replicating
Key Edge Pattern: Use a dedicated pattern. a wipe pattern (Multi)” (page 109).
When the [Key Edge Pattern] button is selected, press
the [Pattern Select] button. In the pattern selection Aspect:
window, set the button for the target pattern to the on Set the [Aspect] button to the on state and set the
state and press [OK]. parameters.
For details about setting parameters, see “Setting the
Note aspect ratio of a wipe pattern (Aspect)” (page 109).
Dedicated patterns 1 to 24 are the same as standard Rotation (angle):
wipe patterns 1 to 24. Set the [Angle] button in the [Rotation] group to the on
state and set the parameters.
4 Press the [Color 1] button and set color 1 using the
For details about setting parameters, see “Rotating a
following parameters.
wipe pattern (Rotation)” (page 108).
Note
Selecting the key fill/key source signals
The [Color 1] button parameters are shared with the
[Matte] button parameters in the [Key Fill] group in You can select a key fill signal and a key source signal in
the Home > M/E-1 > Key1 > Type > Type Select menu the menu.
(11101.11).
For details about selecting a signal in the cross-point
5 Press the [Color 2] button and set color 2 using the control block, see “Selecting a key fill signal/key source
following parameters. signal” (page 51) and “Selecting a video signal/key
signal” (page 51).
79
2 Press the [Edit] button for [Fill]. Note
The [Key Fill Bus] window appears. If the system signal format is different than the image size,
the following processing occurs with the origin at the top
3 Set the button for the target video signal to the on state. left of the image.
Select a tab to change the V/K pair number to display. - If an image size is smaller, the missing part is filled with
black.
4 Press [OK]. - If an image size is larger, the excess part is cropped and
removed.
To select a key source signal Even when image size processing occurs, the thumbnail
When the key source signal is set to split mode, select a key image is not changed.
source signal.
1 Open the Home > M/E-1 > Key5 > SL Key > Load
1 Open the Home > M/E-1 > Key1 > Type > Signal menu (11105.61).
Select menu (11101.14).
Content can be displayed in list view or thumbnail
2 Press the [Source Type] button for [Source], and select view.
video signal/key signal from the pull-down list. To change content properties
Video: Video signal Press the [Edit Properties] button and edit the
Key: Key signal properties in the [Edit Properties] window.
For details, see “Editing Content Properties”
3 Press the [Edit] button for [Source]. (page 275).
The [Key Source Bus] window appears. 2 Select content to load.
4 Set the button for the target video signal/key signal to To select and load multiple content, place a check
the on state. mark beside the target content to load.
To select and load all content, place a check mark in
Select a tab to change the V/K pair number to display. the Select All checkbox.
5 Press [OK]. 3 Press the [Load to Memory] button.
For details about content operations, see “Content Content can be displayed in list view or thumbnail
Operations” (page 271). view.
This section describes the M/E-1 key 5 menu as an 2 Select content to unload.
example. To select and unload multiple content, place a check
mark beside the target content to unload.
Note To select and unload all content, place a check mark in
the Select All checkbox.
Content loading and unloading operations are common to
the key 5 to key 8 menus. Content cannot be loaded/
unloaded individually for each key.
3 Press the [Unload from Memory] button.
To unload currently recalled content
Loading content Place a check mark in [Forcibly unload recalled
contents].
You can load content into SL key memory from content
storage. 4 Check the message, then press [OK].
80
Recalling key fill/key source content
You can recall content for selection as a key fill/key source Key Edges
for SL keys.
1 Open the Home > M/E-1 > Key5 > SL Key > Recall When edge type is selected, you can add modifiers, such as
menu (11105.63). a border, to the key.
This section describes the M/E-1 key 1 menu as an
Content can be displayed in list view or thumbnail example.
view.
Note
The [Density] parameter for an emboss and the
[Density] parameter for the key can be adjusted
separately. When the [Density] parameter for the key
is set to 0.00, the key edge has the density set for the
emboss.
For details about the [Density] parameter for a key,
see “Setting the key type” (page 73).
81
3 Set the signal to insert in the edge. 2 Set the [Separate Edge] button to the on state.
For a border, drop border, or shadow 3 Set the [Border] button or the [Outline] button in the
In the [Edge Fill] group, select an edge fill signal. [Edge] group to the on state and set the following
Utility 1 Bus : Utility 1 bus signal parameters.
For details about selecting a signal, see “Chapter 4
Selecting Signals” (page 46). No. Parameter Adjustment
Matte: Color matte 1 Top Top edge width
When the [Matte] button is selected, set color 1 using 2 Left Left edge width
the following parameters. 3 Right Right edge width
No. Parameter Adjustment 4 Bottom Bottom edge width
1 Luminance Luminance 5 Density Density
2 Saturation Saturation
3 Hue Hue Setting fine key adjustments
For an outline You can adjust the position of the top, bottom, left, and
The key fill signal selected by the key is inserted in the right edges of the key source separately.
outline. The background signal is inserted in the rest of
the image. Notes
For an emboss • When the key type is a key wipe pattern key, fine key
In the [Emboss Fill] group, set the emboss color. cannot be used.
Matte 1: Color matte 1 • When the edge type is emboss, fine key cannot be used.
Matte 2: Color matte 2 • When the edge type is normal, drop border, or shadow,
Set the following parameters. enabling fine key enables key drop.
No. Parameter Adjustment 1 Open the Home > M/E-1 > Key1 > Edge > Edge Type
1 Luminance Luminance Select menu (11101.21).
2 Saturation Saturation
2 Set the [Fine Key] button to the on state and set the
3 Hue Hue following parameters.
1 Open the Home > M/E-1 > Key1 > Edge > Edge Type 2 Set the [Mix Color] button in the [Edge Matte] group
Select menu (11101.21). to the on state and set the following parameters.
82
To set modifiers for a dedicated pattern for a
No. Parameter Adjustment color mix
1 Size Pattern size You can set the following modifiers.
2 Soft Softness of the pattern contour Position:
Set the [Position] button to the on state and set the
5 Pattern Pattern number a)
parameters.
a) Linked to the pattern number selected using the [Mix Pattern Select]
button.
For details about setting parameters, see “Setting the
wipe pattern position (Position)” (page 108).
To set a single color, set the [Flat Color] button to the Multiplication:
on state. Set the [Multi] button to the on state and set the
parameters.
Note
For details about setting parameters, see “Replicating
The [Flat Color] button parameters are shared with the a wipe pattern (Multi)” (page 109).
[Matte] button parameters in the [Edge Fill] group in
the Home > M/E-1 > Key1 > Edge > Edge Type Select Aspect:
menu (11101.21). Set the [Aspect] button to the on state and set the
parameters.
3 Press the [Mix Pattern Select] button. For details about setting parameters, see “Setting the
aspect ratio of a wipe pattern (Aspect)” (page 109).
A pattern selection window appears.
Rotation (angle):
Note Set the [Angle] button in the [Rotation] group to the on
state and set the parameters.
Dedicated patterns 1 to 24 are the same as standard
wipe patterns 1 to 24. For details about setting parameters, see “Rotating a
wipe pattern (Rotation)” (page 108).
4 Set the button for the target pattern to the on state.
Rotation (speed):
Set the [Speed] button in the [Rotation] group to the on
5 Press [OK].
state and set the parameters.
6 Press the [Color 1] button and set color 1 using the For details about setting parameters, see “Rotating a
following parameters. wipe pattern (Rotation)” (page 108).
83
To set to key drop off mode, set the [Key Drop] button Setting a zabton pattern
to the off state.
1 Open the Home > M/E-1 > Key1 > Edge > Zabton
3 Set 8H mode/4H mode using the [8H Mode] button. Adjust menu (11101.23).
On: 8H mode
Move the key fill/key source position downward
2 In the [Zabton Pattern] group, select a zabton pattern.
by eight lines. Key Wipe: Pattern for key wipe pattern key
Off: 4H mode Key Edge Pattern: Pattern for key edge color mix
Move the key fill/key source position downward Mask Pattern: Pattern for main mask source
by four lines.
3 Press the [Pattern Select] button.
Setting the key delay mode A pattern selection window appears.
When frame delay mode is enabled, key drop is set to key
drop off mode (fixed) regardless of the key edge settings. 4 Set the button for the target pattern to the on state.
• The resizer function is used in frame delay mode. Frame 6 Press the [Zabton Color] button and set the zabton
delay mode is enabled only when the conditions for use color using the following parameters.
of the resizer are satisfied.
• When using dual resizer effects, frame delay mode is
disabled on the two target keys. No. Parameter Adjustment
• When frame delay mode is enabled, the video has a one- 1 Luminance Luminance
frame delay. 2 Saturation Saturation
3 Hue Hue
1 Open the Home > M/E-1 > Key1 > Edge > Edge Type
4 Density Density
Select menu (11101.21).
To set modifiers for a zabton pattern
2 Enable/disable frame delay mode using the [Frame Pattern for key wipe pattern key:
Delay] button in the [Key Delay Mode] group. Press the [Pattern Adjust] button, open the Home > M/
On: Enable frame delay mode. E-1 > Key1 > Transition > Wipe menu (11101.52), and
Off: Disable frame delay mode. set modifiers.
For details about setting modifiers, see “Setting
Independent Key Transition Wipe Modifiers”
Setting a Zabton (page 108).
Pattern for key edge color mix:
Note Press the [Pattern Adjust] button, open the Home > M/
E-1 > Key1 > Edge > Matte Adjust menu (11101.22),
When the edge type is emboss, a zabton cannot be set.
and set modifiers.
1 Open the Home > M/E-1 > Key1 > Edge > Edge Type For details about setting modifiers, see “To set
Select menu (11101.21). modifiers for a color mix pattern” (page 79).
Pattern for main mask source:
2 Set the [Zabton] button to the on state and set the
Press the [Pattern Adjust] button, open the Home > M/
following parameters.
E-1 > Key1 > Mask menu (11101.31), and set
modifiers.
No. Parameter Adjustment
For details about setting modifiers, see “To set
1 Size Pattern size modifiers for a mask pattern” (page 85).
2 Soft Softness of the pattern contour
3 Density Density
84
To set modifiers for a mask pattern
Masks You can set the following modifiers when a mask pattern
is selected.
Position:
Set the [Position] button to the on state and set the
You can set a main mask and sub mask.
parameters.
This section describes the M/E-1 key 1 menu as an
example. For details about setting parameters, see “Setting the
wipe pattern position (Position)” (page 108).
Multiplication:
Setting a Mask Set the [Multi] button to the on state and set the
parameters.
Setting a main mask For details about setting parameters, see “Replicating
a wipe pattern (Multi)” (page 109).
1 Open the Home > M/E-1 > Key1 > Mask menu
Aspect:
(11101.31).
Set the [Aspect] button to the on state and set the
2 In the [Mask Type] group, select a mask type. parameters.
For details about setting parameters, see “Setting the
Key Mask: Key mask aspect ratio of a wipe pattern (Aspect)” (page 109).
Bkgd Mask: Background mask
Rotation (angle):
3 In the [Mask Source] group, select a mask source. Set the [Angle] button in the [Rotation] group to the on
state and set the parameters.
Box: Box
Pattern: Mask pattern For details about setting parameters, see “Rotating a
When the [Box] button is selected, set the following wipe pattern (Rotation)” (page 108).
parameters. Rotation (speed):
No. Parameter Adjustment Set the [Speed] button in the [Rotation] group to the on
state and set the parameters.
1 Top Position of top edge
2 Left Position of left edge
For details about setting parameters, see “Rotating a
wipe pattern (Rotation)” (page 108).
3 Right Position of right edge
4 Bottom Position of bottom edge
Setting a sub mask
5 Soft Softness of box
When the [Pattern] button is selected, set the following 1 Open the Home > M/E-1 > Key1 > Mask menu
parameters. (11101.31).
No. Parameter Adjustment 2 In the [Sub Mask Type] group, select a sub mask type.
1 Size Pattern size
Key Mask: Key mask
2 Soft Softness of the pattern contour Bkgd Mask: Background mask
5 Pattern Pattern number (1 to 24)
3 Press the [Sub Mask Adjust] button and set a sub mask
Notes source using the following parameters.
• You can also select a mask pattern by pressing the The utility 1 bus signal is used for the sub mask source.
[Mask Ptn Select] button and selecting from the For details about selecting a signal, see “Chapter 4
pattern selection window. Selecting Signals” (page 46).
• Mask patterns 1 to 24 are the same as standard wipe
patterns 1 to 24. No. Parameter Adjustment
1 Clip Reference level for mask
To invert a mask area
creation
Set the [Mask Invert] button to the on state.
2 Gain Gain
85
To invert a mask area
Set the [Sub Mask Invert] button to the on state.
Processed Key
* The Processed Key function is not supported
in version 1.0.
DME restrictions
• To use the DME function, the XKS-G1600 GPU Pack
(option) and XZS-G1610 3D DME License (option) are
required.
When the system signal format is 2160P, the DME
function must be enabled for use.
For details about setting GPU functions, see “Setting a
GPU” (page 286).
• The number of DME channels that can be used will vary,
depending on the system signal format and the DME
enhanced function mode setting.
For details, see “DME channels” (page 142).
• In processed keys and DME wipes, only enabled DME
channels on the switcher bank can be used.
For details about setting DME channels, see “Setting a
DME channel to use in a switcher bank” (page 309).
• On keys with resizer enabled, DME effects cannot be
used.
Number of DME channels that can be used
simultaneously
DMEs can be used in up to two locations (processed keys
with DME wipe or image effect) simultaneously on a
single switcher bank.
The number of DME channels that can be used on a key
depends on the DME wipe pattern execution mode and the
image effect function, as given below.
When not using a DME wipe or image effect function:
One DME channel each on two keys, or one to four
DME channels on a single key can be used.
When using a 1-channel mode DME wipe or when using
the image effect function on background A or B:
One DME channel on a single key only can be used.
When using a 2-channel mode or 3-channel mode DME
wipe or when using the image effect function on both
background A and B:
DMEs cannot be used on keys.
Notes
• In multi program 2 mode, DMEs can be used in up to two
locations (main and sub).
86
• When M/E split is enabled, DMEs can be used in one For details about selecting a signal, see “Chapter 4
location each on two sub blocks. Selecting Signals” (page 46).
2 In the [DME Select] group, select a DME channel Assigning to DME monitor outputs
(DME 1 to DME 4) to assign.
1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key
You can check the DME channel status using the > Monitor menu (11101.44).
button display.
On: DME channel assigned to the selected key 2 Set the [Monitor Set] button to the on state.
Off: DME channel not assigned
Lock icon: DME channel assigned to a different key/ 3 In the [DME Select] group, select a DME channel
bus (DME 1 to DME 4) to assign.
To select a DME channel assigned to a different Only DME channels assigned to the selected key can
key or bus be selected.
Use the override function. You can release the DME The output of the selected DME channel is assigned to
channel assignment for another key/bus and then select the the monitor output (DME MON V and DME MON K),
DME channel. and the [Monitor Set] button switches to the off state.
To enable the override function, set the [Override] button
to the on state.
The DME channel is assigned to the selected key and the
lock icon displayed on the DME channel button
disappears.
1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key
> Resizer Adjust/DME Select menu (11101.41).
87
2 Set the [Video Process] button to the on state and set
Other Settings the following parameters.
Setting blinking
1 Open the Home > M/E-1 > Key1 > Type > Type Select
menu (11101.11).
Video Process
The video process function adjusts the luminance and hue
of the key fill signal.
This section describes the M/E-1 key 1 menu as an
example.
1 Open the Home > M/E-1 > Key1 > Type > Type Select
menu (11101.11).
88
Two-Dimensional Transforms on
Resizer Keys
A resizer is used to set a two-dimensional transform or Reducing, enlarging, moving, and rotating
effect on a key.
This section describes an example setting a resizer on key
keys (menu)
1 on M/E-1.
1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key
> Resizer Adjust/DME Select menu (11101.41).
Overview 2 Set the [Resizer] button to the on state and set the
following parameters.
A resizer is used to set a two-dimensional transform
(move, enlarge/reduce, rotate) or border/crop on a key.
It can also add the following resizer effects to a key. No. Parameter Adjustment
• Wide key border 1-1 Location X Movement in horizontal
• Drop shadow direction
• Edge enhance 1-2 Location Y Movement in vertical direction
• Mosaic 1-3 Size Size of key
• Defocus
• Mask 1-4 Rotation X Rotation around X-axis a)
• Rotation Rotation Y Rotation around Y-axis b)
The resizer is configured using the menu. 1-5 Perspective Viewpoint position
Two-dimensional transform and crop/border settings are (perspective)
configured using the device control block. 2-1 Aspect X Aspect ratio in horizontal
direction
Dual resizer effects
Two resizers must be used for the following resizer effects. 2-2 Aspect Y Aspect ratio in vertical
direction
Effects that use two resizers are called “dual resizer
effects.” 2-3 Aspect Ratio Simultaneous adjustment of
aspect ratio in horizontal
• Wide key border direction and vertical direction
• Drop shadow
• Mask a) When the [X] button is selected in the [Rotation] group
In a dual resizer effect, key combinations of key 1 and key b) When the [Y] button is selected in the [Rotation] group
2, key 3 and key 4, key 5 and key 6, key 7 and key 8 are
used. Reducing, enlarging, moving, and rotating
When a dual resizer effect is set on either of the two keys, keys (device control block)
the other key cannot be used for a resizer, DME wipe, or
Switch the device control block to resizer operation mode
resizer DME wipe.
to operate a two-dimensional transform.
89
The [RSZR ON] button turns on and the resizer is To return two-dimensional transform parameters
enabled. to the initial settings
Press the [CLR WORK BUFR] button once.
4 Transform the key. The two-dimensional transform parameters return to the
initial status saved data setting values.
To change the aspect ratio of a key
Press the [ASP PERS] button, turning it on, and adjust To return all resizer parameters to the initial
the setting values using the trackball/Z-ring. settings
Press the [CLR WORK BUFR] button twice. Or press and
To change the position and size of a key hold the [SHIFT] button and press the [CLR WORK
Press the [LOC SIZE] button, turning it on, and adjust BUFR] button.
the setting values using the trackball/Z-ring. The resizer parameters return to the initial status saved
To change the rotation and viewpoint position of a data setting values.
key To return a switcher bank to the initial settings
Press the [ROT] button, turning it on, and adjust the Press the [M/E DEF RCALL] button twice.
setting values using the trackball/Z-ring. The selected switcher bank returns to the initial status
To finely adjust the setting values of parameters saved data setting values.
Press the [FINE] button, turning it on.
The adjustment mode switches to fine mode, enabling
fine adjustment of setting values using the trackball/Z- Setting Rotation
ring.
To restrict the parameters targeted by the
1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key
> Resizer Adjust/DME Select menu (11101.41).
operation
Press the [X] button, [Y] button, or [Z] button, turning
it on.
2 Set the [Resizer] button to the on state.
This enables operation only for the selected axis using
the trackball/Z-ring.
3 In the [Rotation] group, select a direction of rotation.
X: Rotation in horizontal direction
Transforming an image using trackball/Z-ring
Y: Rotation in vertical direction
operations
When the [X] button is selected, set the following
You can transform an image as follows using trackball/Z-
parameters.
ring operations for each two-dimensional transform.
No. Parameter Adjustment
Button Trackball Z-ring
1 Rotation X Rotation in horizontal direction
Horizontal Vertical
direction direction 4 Perspective Viewpoint position
(perspective)
ASP Change aspect Change aspect Simultaneous
PERS ratio in X-axis ratio in Y-axis change aspect
When the [Y] button is selected, set the following
direction direction ratio in X-axis
direction and Y- parameters.
axis direction
No. Parameter Adjustment
LOC Movement in Movement in Y- Scaling (shrink/
SIZE X-axis axis direction magnify) 1 Rotation Y Rotation in vertical direction
direction 4 Perspective Viewpoint position
ROT Rotation Rotation Change (perspective)
around Y-axis around X-axis distance from
viewpoint
position
Removing the Virtual Image
To change parameters to the closest detent
position When the perspective of an image is changed, portions
Press the [CTR] button once. beyond the virtual viewpoint may be displayed wrapped
around on the monitor screen (virtual image). You can
To return two-dimensional transform parameters make a setting so the virtual image portions are not
to the default values displayed.
Press the [CTR] button twice. Or press and hold the
[SHIFT] button and press the [CTR] button. 1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key
> Resizer Adjust/DME Select menu (11101.41).
90
2 Set the [Resizer] button to the on state. No. Parameter Adjustment
5 All Simultaneous adjustment of
3 Set the [Wrap Around] button to the on state. position of top, bottom, left,
and right edges
The virtual image portions are removed.
When the [Beveled Color Edge] button is selected,
select the target edge (Top, Left, Right, Bottom, All)
Setting a Border to adjust in the [Color Adjust] group and set the
following parameters.
No. Parameter Adjustment For details about assigning buttons, see “Assigning
1 Luminance Luminance
Control Panel Buttons” (page 317).
2 Saturation Saturation 1 Press the [M/E 1] button.
3 Hue Hue
2 Left Position of left edge 5 Adjust the border width using the trackball or Z-ring.
3 Right Position of right edge
Trackball (horizontal rotation): Adjusts the border
4 Bottom Position of bottom edge width in the X-axis direction (left/right edges)
91
Trackball (vertical rotation): Adjusts the border
width in the Y-axis direction (top/bottom edges) No. Parameter Adjustment
Z-ring: Adjusts the border width simultaneously in 1 Soft Edge softness
the X-axis and Y-axis directions
To finely adjust the setting values of parameters Setting a crop (device control block)
Press the [FINE] button, turning it on. When the crop setting is enabled in the menu, you can
The adjustment mode switches to fine mode, enabling adjust the crop of the top, bottom, left, and right edges
fine adjustment of setting values using the trackball/Z- using the device control block.
ring.
To restrict the parameters targeted by the Note
operation The buttons used for configuring a crop must be assigned
Press the [X] button, [Y] button, or [Z] button, turning to the operation buttons of the device control block
it on. beforehand.
This enables operation only for the selected axis using
the trackball/Z-ring. For details about assigning buttons, see “Assigning
Control Panel Buttons” (page 317).
Note
2 Press the [K1RSZ] button.
When a video signal and key signal are selected for resizer 3 Press the [RSZR ON] button, turning it on.
mosaic/defocus, crop is disabled.
4 Press and hold the [SHIFT] button, and press the
[BDR/CROP] button, turning it on green.
Setting a crop (menu)
1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key
5 Select the target edge to crop using the [X] button/[Y]
button/[Z] button/[CTR] button and adjust the crop
> Resizer Adjust/DME Select menu (11101.41). using the Z-ring.
2 Set the [Resizer] button to the on state. [X] button: Adjustment of crop of top edge
[Y] button: Adjustment of crop of left edge
3 Set the [Crop] button to the on state and set the [Z] button: Adjustment of crop of right edge
following parameters. [CTR] button: Adjustment of crop of bottom edge
If an edge to crop is not selected, operating the Z-ring
No. Parameter Adjustment
adjusts the crop width of all edges.
1-1 H Simultaneous adjustment of To finely adjust the setting values of parameters
crop of left and right edges a) Press the [FINE] button, turning it on.
1-2 V Simultaneous adjustment of The adjustment mode switches to fine mode, enabling
crop of top and bottom edges fine adjustment of setting values using the Z-ring.
a)
92
automatically enables clean mode on both key 1 and key The created CG border is rendered as follows.
2.
• Inserting key 1 also inserts key 2 in unison. Selecting/
releasing key 1 in a next transition also selects/releases
key 2 in unison. Inserting/removing key 2 only and
transition operations using key 2 only are not possible.
• When a CG border is set, key 1 has the following
restrictions. The image to embed in the border and the key signal for
- Dual resizer effects are not supported. keying the image are selected on key 1. The border image
- Resizer border and crop settings are disabled. and the key signal for the image are selected on key 2.
- The target of resizer mosaic and defocus settings is
fixed to the video signal only. 1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key
• A CG border cannot be set using key 1 if the state of key > Resizer Adjust/DME Select menu (11101.41).
2 is any of the following.
- If key 2 is currently inserted or used in a transition 2 Set the [Resizer] button to the on state.
- When key 2 is selected in a next transition
- When the resizer of key 2 is enabled 3 Set the [CG Border] button in the [CG Border] group
- When DME wipe is selected for the transition type for to the on state and set the following parameters.
key 2
• The CG border settings are saved separately in key 1 and
No. Parameter Adjustment
key 2 key snapshots. When recalling, it is necessary to
recall the two key snapshots at the same time. 1 Location X Horizontal position
2 Location Y Vertical position
Signals used in a CG border
Four signals are required for a CG border. 3 Size Size
Note
Locking the CG border setting sets all resizer parameters
2. Border image key signal to the default values, and the settings cannot be changed.
93
Mode1: Even when the picture is reduced, add 3 Set the [Dual Rszr Effect] button to the on state.
compensation so that it can be seen clearly
(standard). 4 Set the [Drop Shadow] button to the on state and set
Mode2: Suppress aliasing when enlarging or reducing the following parameters.
the picture (soft).
Mode3: Do not suppress aliasing when enlarging or No. Parameter Adjustment
reducing the picture (sharp).
1 H Shadow position in the
horizontal direction
2 V Shadow position in the vertical
Setting Resizer Effects direction
3 Size Shadow size
Setting a wide key border 4 Soft Softness of shadow a)
5 Density Density of shadow
1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key
> Enhanced Effect menu (11101.42). a) Common to the [Soft] wide key border parameter.
No. Parameter Adjustment 3 Set the [Edge Enhance] button to the on state and set
the following parameters.
1 H Simultaneous adjustment of
border width of left and right
edges No. Parameter Adjustment
2 V Simultaneous adjustment of 1 H Gain in horizontal direction
border width of top and bottom
edges 2 V Gain in vertical direction
3 All Simultaneous adjustment of 3 All Simultaneous adjustment of
border width of top, bottom, gain in horizontal direction and
left, and right edges vertical direction
4 Soft Softness of border a)
5 Density Density of border Setting a mosaic
a) Common to the [Soft] drop shadow parameter.
1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key
> Enhanced Effect menu (11101.42).
5 Set the [Border Color] button to the on state and set the
following parameters.
2 Set the [Resizer] button to the on state.
No. Parameter Adjustment 3 Set the [Mosaic] button to the on state and set the
1 Luminance Luminance following parameters.
2 Saturation Saturation
3 Hue Hue No. Parameter Adjustment
1 Size Tile size
To add an outline to a wide key border
2 Aspect Tile aspect ratio
Set the [Outline] button to the on state.
• Negative values expand
vertically.
Setting a drop shadow • Positive values expand
horizontally.
1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key
4 In the [Mosaic/Defocus Mode] group, select a signal to
> Enhanced Effect menu (11101.42).
which to apply the mosaic effect.
2 Set the [Resizer] button to the on state. Video/Key: Video signal and key signal
94
Video: Video signal 1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key
> Enhanced Effect menu (11101.42).
Note
2 Set the [Resizer] button to the on state.
When a video signal and key signal are selected for
mosaic, crop and mask are disabled. 3 Set the [Dual Rszr Effect] button to the on state.
To make a mosaic look like a relief
Set the [Relief] button to the on state and set the following 4 Set the [Mask] button to the on state.
parameters.
5 In the [Mask Source] group, select a mask source.
No. Parameter Adjustment
Box: Box
3 Gain Tile gain Circle: Circle
4 Angle Light source direction Set the following parameters.
1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key 2 V Vertical position
> Enhanced Effect menu (11101.42). 3 Size Size
4 Soft Softness
2 Set the [Resizer] button to the on state. 5 Aspect Aspect ratio
3 Set the [Defocus] button to the on state and set the To rotate a mask pattern
following parameters. In the [Rotation] group, select a rotation type.
Angle: Incline a pattern at a fixed angle.
No. Parameter Adjustment Speed: Rotate a pattern at a fixed speed.
When the [Angle] button is selected, set the following
1 H Defocusing in horizontal
direction
parameter.
2 V Defocusing in vertical direction No. Parameter Adjustment
3 All Simultaneous defocusing 1 Angle Inclination angle of pattern
adjustment in horizontal • A value of –1.00 corresponds to
direction and vertical direction a rotation of one turn
counterclockwise.
4 In the [Mosaic/Defocus Mode] group, select a signal to • A value of +1.00 corresponds to
which to apply the defocus effect. a rotation of one turn clockwise.
• A value of 0.00 corresponds to
Video/Key: Video signal and key signal no rotation.
Video: Video signal
When the [Speed] button is selected, set the following
parameter.
Note
When a video signal and key signal are selected for No. Parameter Adjustment
defocus, crop and mask are disabled. 1 Speed Rotation speed of pattern
• A value of –100.00 corresponds
To remove the black level leakage that occurs at to 4 revolutions/second
the edges of the screen counterclockwise rotation.
Set the [Clean Defocus] button to the on state. • A value of +100.00 corresponds
to 4 revolutions/second
clockwise rotation.
Setting a mask • A value of 0.00 corresponds to
no rotation (stationary).
Notes
To invert a mask area
• When a video signal and key signal are selected for Set the [Mask Invert] button to the on state.
resizer mosaic/defocus, mask is disabled.
• When a mask effect is applied to a border, the boundary
becomes discontinuous, giving an unnatural effect.
Avoid applying a mask to a border.
95
3 Press and hold the [KEY] button and press the button
Key Snapshots for the target register to save.
The register button is lit orange and the key settings are
saved in the snapshot.
You can save key settings (excluding key inserted/
removed (on/off) status and key priority) in a register and
Note
recall the settings when required. Settings information of
cross-points, key modifiers, and independent key If you press a register button in which a key snapshot
transitions can be selected and recalled. There are four key is already saved, the register data will be overwritten.
snapshot registers for each key.
Recalling a key snapshot
For details about editing a key snapshot register, see “Key
Snapshot Register Operations” (page 225).
1 Press the [KEY] button.
Saving and recalling a key snapshot can be performed The memory recall section switches to key operation
using the Flexi Pad control block or the menu. mode.
96
Saving a key snapshot 1 Open the Home > M/E-1 > Key1 > Key Snapshot
Set a key and save a key snapshot register using the menu (11101.71).
following procedure.
2 Press the [Delete] button in the [Mode] group.
1 Open the Home > M/E-1 > Key1 > Key Snapshot
3 Press the button for the target register to delete.
menu (11101.71).
The key snapshot is deleted and the register button
2 Press the [Store] button in the [Mode] group. changes to register number display.
If you press a register button in which a key snapshot 1 Open the Home > M/E-1 > Key1 > Key Snapshot
is already saved, the register data will be overwritten. menu (11101.71).
Setting the key snapshot recall mode 2 Press the [Rename] button in the [Mode] group.
You can select the settings information to recall in a key
snapshot and save it for each register.
3 Press the button for the target register to rename.
The [Rename] window appears.
1 Open the Home > M/E-1 > Key1 > Key Snapshot
menu (11101.71). 4 Enter a register name (up to 8 characters) and press
[OK].
2 Press the button for the target register to set.
1 Open the Home > M/E-1 > Key1 > Key Snapshot
menu (11101.71).
Note
97
Wipes
Note
Chapter 7
Overview In an independent key transition, a pattern mix cannot be
used.
A wipe is a function that switches from the current image Dust mix
to a new image using a wipe pattern. This applies a diamond dust wipe effect to a pattern created
You can also switch the background and insert/remove using a wipe pattern or pattern mix.
keys depending on the wipe.
There are two types of wipe: wipes that can be set in a
common transition, and wipes that can be set in an Wipe pattern modifiers
independent key transition. You can add various modifiers to a wipe pattern, such as
setting the wipe direction and pattern position.
Wipe patterns
Wipe patterns are classified into the following groups. Pattern limit
Only standard wipe patterns can be used in an independent You can specify the transition execution limit of a wipe.
key transition.
For details, see “Pattern Limit” (page 63).
For the pattern images, see “Wipe Pattern List”
(page 366). Note
In an independent key transition, a pattern limit cannot be
Pattern group Description used.
Standard wipes Patterns consisting of straight lines
vertically, horizontally, or diagonally,
and circular patterns
Enhanced wipes Patterns such as stars, hearts, and
round corners
Rotary wipes Patterns that rotate an image about
a point
Mosaic wipes Patterns that divide an image into
small tiles
Random/diamond Patterns that display small tiles
dust wipes randomly, and patterns that generate
fine particles
Pattern mix
You can create a new pattern by mixing two patterns (main
and sub).
Four types of pattern mix can be created: mix, positive
non-additive mix (NAM), negative non-additive mix
(NAM), and morphing mix.
98
b) At –100.00, tiles in all rows appear simultaneously; at +100.00, tiles
appear in the next row after the tiles in the previous row are completely
Setting a Wipe displayed.
Adjusting wipe pattern parameters In an independent key transition, a pattern mix cannot be
When the following patterns are selected, set the used.
parameters. Pattern mix Description
Enhanced wipe pattern number 49 (polygon wipe) Mix The effect of the sub pattern is added to
the main pattern, modifying the outline or
No. Parameter Adjustment nature of the main pattern.
1 No. Number of corners Positive NAM Creates a pattern with an outline
a) (+ NAM) comprising the sub pattern superimposed
2 Star Rate Sharpness of the corner on the main pattern.
a) A value of –100.00 completely replaces the corner with a rounded arc, and Negative NAM Creates a pattern with an outline
a value of +100.00 the corners are in the most pointed state. (– NAM) comprising the overlap of the sub pattern
and main pattern.
Mosaic wipe pattern numbers 200 to 203, 206 to
213, 224 to 247, 250 to 257, 260 to 269 Morphing As a transition progresses, the pattern
changes. It morphs from the main pattern,
through a mix of main and sub, to the sub
No. Parameter Adjustment
pattern.
1 H Tile No. Number of tiles horizontally
2 V Tile No. Number of tiles vertically
a) At –100.00, tiles appear from the top edge or left edge of the screen; at
+100.00, tiles appear from the bottom edge or right edge of the screen.
99
Relationship between main pattern and
sub pattern
Sub patterns may not be available for some patterns,
depending on the selected main pattern.
A pattern mix cannot be configured for the following
combinations of main pattern and sub pattern.
• When the main pattern or sub pattern is a rotary wipe
• When both the main pattern and sub pattern are mosaic
wipes
• When both the main pattern and sub pattern are random/
diamond dust wipes
If the main pattern and sub pattern are in a combination for
Mix Positive NAM Negative NAM which a pattern mix cannot be set, the sub pattern changes
to pattern number 1.
Note
For details, see “Selecting a wipe pattern” (page 99).
When a diamond dust wipe (pattern number 274) is 2 Open the Home > M/E-1 > Bus/Transition > Wipe >
selected, the dust mix effect is not applied. Sub Pattern menu (11109.32) and select a sub pattern.
Select a wipe pattern in the same way as for the main
pattern.
100
Notes Setting Modifiers
• Rotary wipe patterns cannot be selected.
• Some patterns may not be available for a sub pattern, You can add modifiers to modify a wipe pattern.
depending on the selected main pattern.
For details, see “Relationship between main pattern Relationship between wipe pattern and
and sub pattern” (page 100). modifiers
3 Open the Home > M/E-1 > Bus/Transition > Wipe > Some modifiers may not be available, depending on the
Pattern Mix/Edge/Direction menu (11109.33). wipe pattern.
The following table shows the supported modifiers for
4 In the [Pattern Mix] group, select a type of pattern mix. each wipe pattern.
1 Open the Home > M/E-1 > Bus/Transition > Wipe > Main pattern and sub pattern modifiers
Pattern Mix/Edge/Direction menu (11109.33). The following modifiers are common to the main pattern
and sub pattern.
2 Set the [Dust Mix] button to the on state and set the • Direction
following parameters. • Split
• Edge
No. Parameter Adjustment The following modifiers can be set separately for the main
pattern and sub pattern.
1 Mix Ratio Proportion of diamond dust
Modifiers for the main pattern are set in the Main Modify
wipe pattern
menu, and modifiers for the sub pattern are set in the Sub
2 H Size Particle width Modify menu.
3 V Size Particle height • Position
4 Flash Rate Rate of generation of particles • Rotation
• Aspect
101
• Multiplication Splitting a wipe pattern (Split)
• Pairing You can split a wipe pattern, making the parts of the wipe
• Modulation move in opposite directions.
• Spring
• Spiral
This section describes the menu for setting modifiers for
the main pattern as an example.
1 Open the Home > M/E-1 > Bus/Transition > Wipe >
Pattern Mix/Edge/Direction menu (11109.33).
Note
The buttons used for configuring the wipe direction must Soft Border
be assigned to the transition settings section of the Softens a border applied to a pattern.
transition control block beforehand.
102
For the edge fill, you can use a color matte or the utility 2 2 Set the [Mix Color] button in the [Edge Matte] group
bus signal. For a color matte, you can select a single color to the on state and set the following parameters.
(color 1 only) or a color mix (mix of color 1 and color 2).
No. Parameter Adjustment
1 Open the Home > M/E-1 > Bus/Transition > Wipe >
Pattern Mix/Edge/Direction menu (11109.33). 1 Size Pattern size
2 Soft Softness of the pattern contour
2 In the [Edge] group, select a type of edge.
To set a single color, set the [Flat Color] button to the
When the [Border] button is selected, set the following on state.
parameter.
Note
No. Parameter Adjustment
1 Width Border width The [Flat Color] button parameters are shared with the
[Matte] button parameters in the [Edge Fill] group in
When the [Soft] button is selected, set the following the Home > M/E-1 > Bus/Transition > Wipe > Pattern
parameter. Mix/Edge/Direction menu (11109.33).
To set an edge fill 6 Press the [Color 1] button and set color 1 using the
When a border or soft border is selected, set the edge fill. following parameters.
1 Open the Home > M/E-1 > Bus/Transition > Wipe > No. Parameter Adjustment
Pattern Mix/Edge/Direction menu (11109.33).
1 Luminance Luminance
2 In the [Edge Fill] group, select an edge fill signal. 2 Saturation Saturation
3 Hue Hue
Utility 2 Bus: Utility 2 bus signal
For details about selecting a signal, see “Chapter 4 Note
Selecting Signals” (page 46).
The [Color 1] button parameters are shared with the
Matte: Color matte [Matte] button parameters in the [Edge Fill] group in
When the [Matte] button is selected, set color 1 using the Home > M/E-1 > Bus/Transition > Wipe > Pattern
the following parameters. Mix/Edge/Direction menu (11109.33).
No. Parameter Adjustment 7 Press the [Color 2] button and set color 2 using the
1 Luminance Luminance following parameters.
2 Saturation Saturation
3 Hue Hue No. Parameter Adjustment
1 Luminance Luminance
To mix color 1 and color 2 color mattes
When color matte is selected for an edge fill, you can use 2 Saturation Saturation
a dedicated pattern to mix color 1 and color 2. 3 Hue Hue
1 Open the Home > M/E-1 > Bus/Transition > Wipe >
Matte Adjust menu (11109.34).
103
To swap color 1 and color 2 in a color mix
Open the Home > M/E-1 > Bus/Transition > Wipe > Matte No. Parameter Adjustment
Adjust menu (11109.34) and set the [Color Invert] button 1 Position H Horizontal position
to the on state. • Negative values move left.
• Positive values move right.
To set modifiers for a dedicated pattern for a 2 Position V Vertical position
color mix • Negative values move down.
You can set the following modifiers in the Home > M/E-1 • Positive values move up.
> Bus/Transition > Wipe > Matte Adjust menu (11109.34).
Position: To return the pattern position to the center of the
Set the [Position] button to the on state and set the screen
parameters. Press the [Center] button in the [Position] group.
For details about setting parameters, see “Setting the To return a pattern from a moved position to the
wipe pattern position (Position)” (page 108). center of the screen as a transition progresses
Set the [Auto Center] button in the [Position] group to the
Multiplication: on state.
Set the [Multi] button to the on state and set the
parameters.
Rotating a wipe pattern (Rotation)
For details about setting parameters, see “Replicating
a wipe pattern (Multi)” (page 109). Angle
Wipes with a pattern at a fixed angle.
Aspect:
Set the [Aspect] button to the on state and set the
parameters.
For details about setting parameters, see “Setting the
aspect ratio of a wipe pattern (Aspect)” (page 109).
Rotation (angle):
Set the [Angle] button in the [Rotation] group to the on Angle disabled Angle enabled
state and set the parameters.
For details about setting parameters, see “Rotating a Speed
wipe pattern (Rotation)” (page 108). Rotates a pattern at a fixed speed.
Rotation (speed):
Set the [Speed] button in the [Rotation] group to the on
state and set the parameters.
For details about setting parameters, see “Rotating a
wipe pattern (Rotation)” (page 108).
Magnitude
Setting the wipe pattern position (Position) Rotates a pattern through the specified angle in a single
You can move a wipe pattern to a desired position. transition.
Position disabled Position enabled 1 Open the Home > M/E-1 > Bus/Transition > Wipe >
Main Modify menu (11109.35).
1 Open the Home > M/E-1 > Bus/Transition > Wipe >
Main Modify menu (11109.35). 2 In the [Rotation] group, select a rotation type.
When the [Angle] button is selected, set the following
2 Set the [Position] button in the [Position] group to the
parameter.
on state and set the following parameters.
104
No. Parameter Adjustment
1 Angle Inclination angle of pattern
• A value of –100.00
corresponds to a rotation of
one turn counterclockwise.
• A value of +100.00
corresponds to a rotation of Aspect disabled Aspect enabled
one turn clockwise.
• A value of 0.00 corresponds
to no rotation. 1 Open the Home > M/E-1 > Bus/Transition > Wipe >
Main Modify menu (11109.35).
When the [Speed] button is selected, set the following
parameter. 2 Set the [Aspect] button to the on state and set the
following parameter.
No. Parameter Adjustment
1 Speed Rotation speed of pattern
No. Parameter Adjustment
• A value of –100.00
corresponds to 1 revolution/ 1 Aspect Aspect ratio
second counterclockwise • Negative values expand
rotation. vertically.
• A value of +100.00 • Positive values expand
corresponds to 1 revolution/ horizontally.
second clockwise rotation.
• A value of 0.00 corresponds
to no rotation (stationary).
Replicating a wipe pattern (Multi)
You can replicate a pattern horizontally, vertically, or both
When the [Magnitude] button is selected, set the up to 63 times.
following parameters. You can also change the orientation of alternate patterns or
change the position.
No. Parameter Adjustment
1 Angle Angle of pattern at start of
transition
• A value of –100.00
corresponds to a rotation of
one turn counterclockwise.
• A value of +100.00
corresponds to a rotation of
one turn clockwise. Multi disabled Multi enabled
• A value of 0.00 corresponds
to no rotation.
1 Open the Home > M/E-1 > Bus/Transition > Wipe >
2 Magnitude Angle of rotation through Main Modify menu (11109.35).
course of transition
• A value of –200.00
corresponds to a rotation of
2 Set the [Multi] button to the on state and set the
two turns counterclockwise. following parameters.
• A value of +200.00
corresponds to a rotation of No. Parameter Adjustment
two turns clockwise.
• A value of 0.00 corresponds 1 H Multi Number of repetitions of
pattern horizontally
to no rotation.
2 V Multi Number of repetitions of
pattern vertically
Setting the aspect ratio of a wipe pattern 3 Shift Pattern layout
(Aspect) • Negative values move even-
You can change the aspect ratio of a pattern. numbered columns to the
left.
• Positive values move even-
numbered columns to the
right.
105
To adjust replicated patterns No. Parameter Adjustment
In the [Multi Adjust] group in the Home > M/E-1 > Bus/
3 V Offset Spacing in the vertical
Transition > Wipe > Main Modify menu (11109.35), select direction
a pattern adjustment method. • Negative values move the
H Invert: Invert the horizontal orientation of patterns even-numbered group up,
alternately. and the odd-numbered
V Invert: Invert the vertical orientation of patterns group down.
alternately. • Positive values move the
Non-Mask: Ensure a pattern is always visible on the even-numbered group down,
screen, even when the position function is used to and the odd-numbered
group up.
move the pattern position.
Position: Move a pattern within the pattern area divisions
set by repetition (Multi). Adding modulation to a wipe pattern
When the [Position] button is selected, set the following (Modulation)
parameters.
H (horizontal modulation)
No. Parameter Adjustment This modulates the pattern in the horizontal direction.
1 Position H Horizontal position
• Negative values move right.
• Positive values move left.
2 Position V Vertical position
• Negative values move down.
• Positive values move up.
1 Open the Home > M/E-1 > Bus/Transition > Wipe >
Main Modify menu (11109.35).
106
No. Parameter Adjustment 2 Set the [Spiral] button to the on state and set the
following parameters.
3 Speed Speed of ripples
• Negative values create
waves in the down, left, and No. Parameter Adjustment
counterclockwise directions.
1 Magnitude Size and direction of the spiral
• Positive values create waves
• A value of –100.00
in the up, right, and
represents the maximum
clockwise directions.
movement in the
4 Shape Modulation waveform a) counterclockwise direction.
• A value of +100.00
a) 1: Sine wave, 2: Triangle wave, 3: Square wave
represents the maximum
movement in the clockwise
Warping the edges of a wipe pattern direction.
(Spring) 2 Wave Speed Speed of the lateral waves
• Negative values set the
This warps the edges of a pattern inward or outward. speed from the left.
• Positive values set the
speed from the right.
1 Open the Home > M/E-1 > Bus/Transition > Wipe >
Main Modify menu (11109.35).
1 Open the Home > M/E-1 > Bus/Transition > Wipe >
Main Modify menu (11109.35).
107
Normal/Reverse: Alternate directions between
Setting an Independent normal and reverse after each transition.
Reverse: Wipe in the opposite direction of the normal
Key Transition Wipe direction.
Only standard wipe patterns can be used in an independent Setting the wipe pattern position (Position)
key transition. You can move a wipe pattern to a desired position.
1 Open the Home > M/E-1 > Key1 > Transition > Wipe 1 Open the Home > M/E-1 > Key1 > Transition > Wipe
menu (11101.52). menu (11101.52).
2 Press the [Pattern Select] button. 2 Set the [Position] button to the on state and set the
following parameters.
A pattern selection window appears.
3 Set the button for the target wipe pattern to the on state. No. Parameter Adjustment
1 Position H Horizontal position
4 Press [OK]. • Negative values move left.
• Positive values move right.
2 Position V Vertical position
• Negative values move down.
Setting Independent Key Transition • Positive values move up.
Wipe Modifiers To return a pattern from a moved position to the
You can set the following modifiers in an independent key center of the screen as a transition progresses
transition. Set the [Auto Center] button to the on state.
• Direction
• Soft edge Rotating a wipe pattern (Rotation)
• Position
• Rotation 1 Open the Home > M/E-1 > Key1 > Transition > Wipe
• Aspect menu (11101.52).
• Multiplication
2 In the [Rotation] group, select a rotation type.
Setting the wipe direction (Direction) Angle: Wipe with a pattern at a fixed angle.
Speed: Rotate a pattern at a fixed speed.
1 Open the Home > M/E-1 > Key1 > Transition > Wipe Magnitude: Rotate a pattern through the specified
menu (11101.52). angle in a single transition.
When the [Angle] button is selected, set the following
2 In the [Direction] group, select a wipe direction. parameter.
Normal: Wipe in normal direction.
108
2 Set the [Aspect] button to the on state and set the
No. Parameter Adjustment following parameter.
1 Angle Inclination angle of pattern
• A value of –100.00
corresponds to a rotation of No. Parameter Adjustment
one turn counterclockwise. 1 Aspect Aspect ratio
• A value of +100.00 • Negative values expand
corresponds to a rotation of vertically.
one turn clockwise. • Positive values expand
• A value of 0.00 corresponds horizontally.
to no rotation.
When the [Speed] button is selected, set the following Replicating a wipe pattern (Multi)
parameter. You can replicate a pattern horizontally, vertically, or both
up to 63 times.
No. Parameter Adjustment
You can select from four types of pattern layout in an
1 Speed Rotation speed of pattern independent key transition.
• A value of –100.00
corresponds to 1 revolution/
second counterclockwise
rotation.
• A value of +100.00
corresponds to 1 revolution/
second clockwise rotation.
• A value of 0.00 corresponds
to no rotation (stationary).
When the [Magnitude] button is selected, set the 1: All patterns in the same orientation
following parameters. 2: Even-numbered rows moved horizontally
3: Even-numbered columns flipped horizontally, even-
No. Parameter Adjustment numbered rows flipped vertically
1 Angle Angle of pattern at start of 4: Even-numbered columns flipped horizontally, even-
transition numbered rows flipped vertically and moved
• A value of –100.00 horizontally
corresponds to a rotation of
one turn counterclockwise. 1 Open the Home > M/E-1 > Key1 > Transition > Wipe
• A value of +100.00 menu (11101.52).
corresponds to a rotation of
one turn clockwise.
• A value of 0.00 corresponds
2 Set the [Multi] button to the on state and set the
to no rotation.
following parameters.
2 Magnitude Angle of rotation through
course of transition No. Parameter Adjustment
• A value of –200.00 1 H Multi Number of repetitions of
corresponds to a rotation of pattern horizontally
two turns counterclockwise.
• A value of +200.00 2 V Multi Number of repetitions of
pattern vertically
corresponds to a rotation of
two turns clockwise. 3 Invert Type Pattern layout (1 to 4)
• A value of 0.00 corresponds
to no rotation.
1 Open the Home > M/E-1 > Key1 > Transition > Wipe
menu (11101.52).
109
The wipe pattern number is displayed on the top right
Wipe Snapshots button in the memory recall section.
The button color varies as follows, according to the
register state.
Gray characters: Register not containing a registered
You can save a snapshot of a wipe pattern together with all
snapshot
modifiers and pattern limit settings in a register for recall
White icon/text: Register containing a registered snapshot
when required. There are ten wipe snapshot registers on
Lit orange: Last recalled register
each switcher bank.
UNDO button
1 Press the [WIPE] button.
WIPE button DEL button The memory recall section switches to wipe snapshot
operation mode.
PTN NO
The memory recall section switches to numeric
1 keypad mode.
PTN
Saving a wipe snapshot
10 NO.
Set a wipe and save a wipe snapshot register using the
following procedure.
110
Note Saving a wipe snapshot
Set a wipe and save a wipe snapshot register using the
If you press a register button in which a wipe snapshot
following procedure.
is already saved, the register data will be overwritten.
1 Open the Home > M/E-1 > Bus/Transition > Wipe >
Recalling a wipe snapshot Wipe Snapshot menu (11109.37).
1 Press the [WIPE] button. 2 Press the [Store] button in the [Mode] group.
The memory recall section switches to wipe snapshot 3 Press the button for the target register to save.
operation mode.
The register button is lit orange and the wipe settings
2 Press the button for the target register to recall. are saved in the snapshot.
2 Press and hold the [DEL] button and press the button 3 Press the button for the target register to recall.
for the target register to delete. The register button is lit orange and the wipe snapshot
The wipe snapshot is deleted and the register button is recalled.
changes to register number display.
Deleting a wipe snapshot
Wipe Snapshot Operations (Menu) 1 Open the Home > M/E-1 > Bus/Transition > Wipe >
Wipe Snapshot menu (11109.37).
The same memory recall buttons as in the memory recall
section of the Flexi Pad control block are displayed in the 2 Press the [Delete] button in the [Mode] group.
Bus/Transition > Wipe > Wipe Snapshot menu on the
switcher bank. The settings and display of the memory 3 Press the button for the target register to delete.
recall buttons in the Flexi Pad control block and in the
menu are linked. The wipe snapshot is deleted and the register button
This section describes the M/E-1 menu as an example. changes to register number display.
1 Open the Home > M/E-1 > Bus/Transition > Wipe >
Wipe Snapshot menu (11109.37).
111
DME Wipes Chapter
* The DME wipe function (excluding resizer DME wipes) is not supported in version 1.0.
8
For the pattern images, see “DME Wipe Pattern List”
Overview (page 367) and “Resizer DME Wipe Pattern List”
(page 370).
112
Pattern group Description DME wipe execution mode and pattern
P in P (Picture-in- In 1-channel mode: numbers
picture) Completed in two transitions. The execution modes and pattern numbers supported in
In the first transition, the current
image shrinks, and the new image
each DME wipe pattern group are shown in the following
appears behind it. In the second table.
transition, the current image expands Depending on the DME wipe pattern, there are patterns
to its original size. that can be used for backgrounds (transition with
In 2-channel mode: background selected for next transition) and patterns that
In the first half of the transition, the
current image shrinks and the new
can be used for keys (transition with key selected for next
image appears behind it. In the transition or independent key transition).
second half of the transition, the new
image expands, and the current a: Supported
image disappears. ×: Not supported
You can move the pattern from the
current position by a relative amount. Pattern group Execution Pattern Background Keys
a) b)
During the transition, the signal from mode number
the utility 2 bus appears as the
Slide 1ch 1001 to a a
background.
1008
Mosaic In the first half of the transition, a
2ch 2601 to a ×
mosaic is gradually applied so that the
2608
current image switches to the new
image by the 50% point. In the second Squeeze 1ch 1021 to a a
half of the transition, the mosaic effect 1033
on the new image is gradually
2ch 2621 to a ×
reversed, returning to the original
2628
image at 100%.
Split 1ch 1011 to a a
Defocus In the first half of the transition, the
1013
defocus effect is gradually applied so
that the current image switches to the Door 1ch 1041 to a a
new image by the 50% point. In the 1044
second half of the transition, the
Flip Tumble 1ch 1101, 1102 a ×
defocus effect on the new image is
gradually reversed, returning to the Page Turn 1ch 1301 to a a
original image at 100%. 1313, 1315
Enhanced function mode DME to 1318,
channels can be used. 1341 to
1345
Crop Slide The current image is cropped in half
as the new image appears, displaying 2ch 2701 to a a
both images side by side. Then, the 2713, 2715
cropped images slide sideways to to 2718,
show only the new image. 2741 to
2745
Brick In 2-channel mode:
A brick with visible side surface slides Roll 1ch 1321 to a a
in over the current image, then rotates 1333, 1335
so that the new image becomes to 1338,
visible. 1346 to
In 3-channel mode: 1350
A brick appears over the current
2ch 2721 to a a
image, expanding and rotating, and
2733, 2735
switches to the new image.
to 2738,
Resizer Slide Executes a Slide DME wipe using a 2746 to
resizer. 2750
Resizer Squeeze Executes a Squeeze DME wipe using Frame I/O 1ch 1201 to a a
a resizer. 1209, 1221
to 1225
Resizer Frame I/O Executes a Frame I/O DME wipe
using a resizer. 2ch 2851 to a ×
2854, 2861
to 2864
P in P 1ch 1251 a ×
2ch 2651, 2652 a ×
Mosaic 1ch 1701 a ×
113
Pattern group Execution Pattern Background Keys • When a dual resizer effect is set on either of the two
mode number a) b) keys, DME wipes and resizer DME wipes cannot be
Defocus 1ch 1702 a × used on the other key.
Crop Slide 2ch 2661, 2662 a × Number of DME channels that can be used
Brick 2ch 2801 to a × simultaneously
2804, 2811 DMEs can be used in up to two locations simultaneously
to 2814 on a single switcher bank (processed key with DME wipe).
3ch 3601 a × The number of DME channels that can be used on a key
Resizer Slide 1ch 7001 to × a depends on the DME wipe pattern execution mode, as
7008 given below.
Resizer 1ch 7021 to × a
When not using a DME wipe:
Squeeze 7031 One DME channel each on two keys, or one to four
DME channels on a single key can be used.
Resizer 1ch 7201 to × a
Frame I/O 7208, 7221 When using a 1-channel mode DME wipe:
to 7224 One DME channel on a single key only can be used.
When using a 2-channel mode or 3-channel mode DME
a) Transition with a background selected for a next transition wipe:
b) Transition with a key selected for a next transition or an independent key
transition DMEs cannot be used on keys.
You can add various modifiers to a DME wipe pattern, • In multi program 2 mode, DMEs can be used in up to two
such as setting the DME wipe direction and pattern locations (main and sub).
position. • When M/E split is enabled, DMEs can be used in one
location each on two sub blocks.
Pattern limit
You can specify the transition execution limit of a DME
wipe.
Note
In an independent key transition, a pattern limit cannot be
used.
114
Adjusting DME wipe pattern parameters
Setting a DME Wipe When the following patterns are selected, set the
parameters.
DME wipe patterns and modifiers are configured using the Squeeze (1-channel mode) pattern numbers 1032,
menu. 1033
This section describes the M/E-1 menu as an example. Crop Slide (2-channel mode) pattern numbers
2661, 2662
115
Frame I/O (2-channel mode) pattern numbers Note
2861 to 2864
The edges cannot be set for the following patterns.
No. Parameter Adjustment • Split pattern numbers 1011, 1012, 1013
1 Rot X Rotation around Y-axis (rotation in • Mosaic pattern number 1701
horizontal direction) • Defocus pattern number 1702
2 Rot Y Rotation around X-axis (rotation in
vertical direction) Position
You can move a DME wipe pattern to a desired position.
3 Rot Z Rotation around Z-axis
You can move to a specified position (upper left, upper
5 Delay Timing for image selected on a right, bottom left, bottom right) using Position Select.
utility bus to enter the frame The position can be set for the following patterns.
Brick (3-channel mode) pattern number 3601 The target position and movement varies depending on the
pattern.
No. Parameter Adjustment • Squeeze pattern number 1031
1-1 Side V Size X Side V horizontal scaling factor Resizer Squeeze pattern number 7031
As the transition progresses, the pattern center
1-2 Side V Size Y Side V vertical scaling factor
automatically moves from the initial set position toward
1-3 Height Height of brick a) the center of the screen.
1-4 Side V Center X Side V horizontal center position b) • Squeeze pattern numbers 1032, 1033
1-5 Side V Center Y Side V vertical center position c) You can set the pattern position at the start of the
transition. As the transition progress resumes after the
2-1 Side H Size X Side H horizontal scaling factor
dead band, the pattern automatically moves from the
2-2 Side H Size Y Side H vertical scaling factor initial position toward the center of the screen.
2-3 Height Height of brick a) • Frame I/O pattern numbers 1201 to 1209, 1221 to 1225
2-4 Side H Center X Side H horizontal center position b) P in P pattern number 1251
Resizer Frame I/O pattern numbers 7201 to 7208, 7221
2-5 Side H Center Y Side H vertical center position c)
to 7224
a) The [Height] parameter in numbers 1-3 and 2-3 are common. You can set the pattern position at the end of the first
b) Side V/side H image horizontal center position. At –100.00, the center is transition.
at the left edge of the screen. At +100.00, the center is at the right edge of
the screen.
• P in P pattern numbers 2651, 2652
c) Side V/side H image vertical center position. At –100.00, the center is at You can configure each channel separately, or configure
the bottom edge of the screen. At +100.00, the center is at the top edge of two channels simultaneously, depending on their
the screen.
relative positions.
• Brick pattern numbers 2801 to 2804, 2811 to 2814
You can set the vertical position where the brick slides
Setting Modifiers in.
• Frame I/O pattern numbers 2851 to 2854, 2861 to 2864
You can add modifiers to modify a DME wipe pattern. You can set the pattern position at the end of the first
Direction transition for each channel.
Sets the direction of travel of the DME wipe. Size
Sets the size of a DME wipe pattern.
Notes
• The direction cannot be set for the following patterns. Note
- Frame I/O pattern numbers 1201, 1202, 1203, 1205, The size can be set for the following patterns.
1206, 1208, 1209, 1225 • Frame I/O pattern numbers 1201 to 1209, 1221 to 1225,
- P in P pattern number 1251 2851 to 2854, 2861 to 2864
- Mosaic pattern number 1701 • P in P pattern numbers 1251, 2651, 2652
- Defocus pattern number 1702 • Resizer Frame I/O pattern numbers 7201 to 7208, 7221
• In a key DME wipe, the direction can be set for the to 7224
following patterns.
- Frame I/O pattern numbers 1204, 1207, 1221 to 1224 Crop
- Resizer Frame I/O pattern numbers 7204, 7207, 7221 Crops the top, bottom, left, right sides of a DME wipe
to 7224 pattern.
Edge
Adds a border to a DME wipe pattern.
116
Note Modifying a DME wipe pattern edge (Edge)
Cropping cannot be set for the following patterns. 1 Open the Home > M/E-1 > Bus/Transition > DME
• Mosaic pattern number 1701 Wipe > Edge/Direction menu (11109.44).
• Defocus pattern number 1702
• Crop Slide pattern numbers 2661, 2662 2 In the [Ch Select] group, select the target channel to
Target channel for modifiers set.
For DME wipe patterns in 1-channel mode, the 1st channel
becomes the target. 3 In the [Edge] group, select a type of edge.
For DME wipe patterns in 2-channel mode, select the Border: Adds a border to a pattern.
target channel from the 1st channel and 2nd channel. For Soft Border: Softens a border applied to a pattern.
DME wipe patterns in 3-channel mode, select the target When the [Border] button is selected, set the following
channel from the 1st channel, 2nd channel, and 3rd parameters.
channel. You can select multiple channels. Depending on
the DME wipe pattern and modifiers, all channels may be No. Parameter Adjustment
controlled by the 1st channel. 1 Width Border width
3 Luminance Luminance
Note
4 Saturation Saturation
Channels cannot be selected for the direction setting. 5 Hue Hue
Note
Setting the DME wipe pattern position
The buttons used for configuring the DME wipe direction (Position)
must be assigned to the transition settings section of the
transition control block beforehand. 1 Open the Home > M/E-1 > Bus/Transition > DME
Wipe > Modify menu (11109.45).
For details about assigning buttons, see “Assigning
Control Panel Buttons” (page 317). 2 In the [Ch Select] group, select the target DME
channel to set.
Press one of the following wipe direction selection
buttons. 3 Set the [Position] button in the [Position] group to the
[NORM] button: Normal on state and set the following parameters.
[NORM/REV] button: Normal/Reverse
[REV] button: Reverse
117
3 Set the [Size] button to the on state and set the
No. Parameter Adjustment following parameter.
1 H a) Horizontal position
• Negative values move left.
• Positive values move right. No. Parameter Adjustment
2 In the [Ch Select] group, select the target DME 1-2 V Simultaneous adjustment of
crop of top and bottom edges
channel to set.
1-3 All Simultaneous adjustment of
crop of top, bottom, left, and
3 In the [Position Select] group, select a move position. right edges
Top Left: Top left corner 2-1 Top Crop of top edge
Top Right: Top right corner 2-2 Left Crop of left edge
Bottom Left: Bottom left corner
2-3 Right Crop of right edge
Bottom Right: Bottom right corner
The button for the current pattern position is in the on 2-4 Bottom Crop of bottom edge
state. When the pattern position is at the center of the
screen, all four buttons are in the on state. Note
When multiple channels are selected, the setting
Note values for the channel with the lowest number are
When multiple channels are selected, the 1st channel displayed. When you adjust the setting values, this
becomes the target for movement. adjusts the settings on the other channels by the same
amount.
Setting the DME wipe pattern size (Size) To crop to 4:3 aspect ratio
Press the [4:3 Crop] button in the [Crop Mode] group.
1 Open the Home > M/E-1 > Bus/Transition > DME
To set the movement during transition execution
Wipe > Modify menu (11109.45).
In the [Crop Transition] group, select the crop operation as
the transition executes.
2 In the [Ch Select] group, select the target DME
Cut: The cropping does not change during the transition,
channel to set.
and the cropping is removed after the transition has
completed.
118
Last 5%: The cropping is maintained for the first 95% of
the transition, and is removed during the last 5% of the Dead band
transition.
Linear: The cropping is removed from the start of the
transition through the course of the transition.
Transition
Crop
t: Transition execution time
y: Change in transition and
cropping amount
Transition
Crop
t: Transition execution time
y: Change in transition and
cropping amount
119
Setting the DME wipe direction (Direction)
Setting an Independent 1 Open the Home > M/E-1 > Key1 > Transition > DME
Key Transition DME Wipe Wipe menu (11101.53).
120
No. Parameter Adjustment Linear: The cropping is removed from the start of the
transition through the course of the transition.
2 V Vertical position
• Negative values move down. To set the timing of transition completion
• Positive values move up.
When the [Last 5%] button in the [Crop Transition] group
To return the pattern position to the center of the is selected, you can set the transition completed timing to
screen 70%, 95%, or 100% of the execution time.
Press the [Center] button in the [Position] group. In the [Release Transition] group, select the timing of
transition completion.
Last 30%: The transition completes at the 70% point of
Setting the DME wipe pattern size (Size) the transition progress. The transition interval from
70% to 95% becomes a dead band. The cropping is
1 Open the Home > M/E-1 > Key1 > Transition > DME removed during the last 5% of the transition.
Wipe menu (11101.53). Last 5%: The transition completes at the 95% point of the
transition progress. The cropping is removed during
2 Set the [Size] button to the on state and set the the remaining 5%.
following parameter. Off: The transition completes at the 100% point. During
the last 5% of the transition, the transition and
No. Parameter Adjustment cropping removal proceed together.
1 Size Size
1 Open the Home > M/E-1 > Key1 > Transition > DME
Wipe menu (11101.53).
121
DME Wipe Snapshots
You can save a snapshot of a DME wipe pattern together
with all modifiers and pattern limit settings in a register for
recall when required. There are ten DME wipe snapshot
registers on each switcher bank.
122
Clip Transitions Chapter 9
Overview Setting a Clip Transition
You can play frame memory video content linked to a This section describes clip transitions using frame memory
background transition, such as a mix or wipe. output channels 1 and 2 on M/E-1 as an example.
A key for a clip transition is mixed with the background
during execution of the transition.
Selecting a Transition Type
Clip transition restrictions
You can select a clip transition on a frame memory output
• Pattern limits cannot be used. channel to use using the transition control block or the
• Transition preview cannot be used. menu.
• It is not possible to set the transition rate of a clip
transition. To select using the transition control block
• A clip transition cannot be saved in an effect timeline as Press a [FM1&FM2 CLIP] to [FM15&FM16 CLIP]
a keyframe. button, turning it on.
• The state of a clip transition during execution cannot be For frame memory output channels 1 and 2, press the
saved in a snapshot. [FM1&FM2 CLIP] button, turning it on.
• When recalling a snapshot that includes a clip transition
while executing another clip transition, the subsequent For details, see “Setting a transition type (transition
transition does not operate properly. Recall the snapshot control block)” (page 58).
after the transition completes.
• When recalling a DME wipe snapshot while executing a
Note
clip transition, the image may be distorted.
• Transitions executed in two strokes, such as a preset When the system signal format is 2160P, only the
color mix when the stroke mode is set to normal mode, [FM1&FM2 CLIP] button, [FM3&FM4 CLIP] button, and
or a DME wipe with a picture-in-picture pattern, will not [FM5&FM6 CLIP] button can be selected.
execute properly.
• When a clip transition is selected, the wipe direction To select using the menu
selection button in the transition control block that is lit In the Home > M/E-1 > Bus/Transition > Transition >
indicates the playback direction of the frame memory Transition Type menu (11109.21), set a [FM 1&2 Clip] to
clip. [FM 15&16 Clip] button in the [Transition Type] group to
the on state.
For frame memory output channels 1 and 2, set the [FM
1&2 Clip] button to the on state.
Note
When the system signal format is 2160P, only the [FM
1&2 Clip] button, [FM 3&4 Clip] button, and [FM 5&6
Clip] button can be selected.
123
pattern. To use a DME wipe pattern in 3-channel
Setting a Clip Transition mode, open the Home > M/E-1 > Bus/Transition >
DME Wipe > 3ch Pattern menu (11109.43) and select
1 Open the Home > M/E-1 > Bus/Transition > a DME wipe pattern.
Transition > Clip Transition menu (11109.22).
For details, see “Setting a DME Wipe” (page 115).
2 Press the [FM1/FM2 Recall] button.
6 In the [Background Transition Timing] group, set the
The Home > Frame Memory > FM1/FM2 > Clip/Still start position and stop position of the background
> Recall menu (13101.11) appears. transition.
Select content for use in a clip transition and recall it
To set the start position
on a frame memory output channel.
Set using any of the following methods.
For details, see “Recalling Video” (page 133). • Move the fader lever to the start position and press
the [Set Start] button.
3 Return to the Home > M/E-1 > Bus/Transition > • Press the button on the right side of the [Set Start]
Transition > Clip Transition menu (11109.22). button and enter a start position in the numeric
keypad window (number of frames).
4 Press the [Linear Key Adjust] button and set a clip
transition key using the following parameters. To set the stop position
Set using any of the following methods.
• Move the fader lever to the stop position and press
No. Parameter Adjustment the [Set Stop] button.
1 Clip Reference level for key signal • Press the button on the right side of the [Set Stop]
generation button and enter a stop position in the numeric
2 Gain Key gain keypad window (number of frames).
3 Density Key density
To reset the start position and stop position
Press the [Reset Timing] button.
5 Press the [Background Transition] button and select a
background transition type from the pull-down list.
7 In the [Background Transition Direction] group, set
Mix: Mix the transition direction of the background transition.
NAM: Non-additive mix
Normal: Normal
Super Mix: Super mix
Normal/Reverse: Normal/reverse
Preset Color Mix: Preset color mix
Reverse: Reverse
Wipe: Wipe
DME Wipe: DME wipe
When [Super Mix] is selected, press the [Super Mix] Note
button and set the parameters. This can be configured only when a wipe or DME
For details, see “Setting Super Mix” (page 59). wipe is selected as the background transition type.
When [Preset Color Mix] is selected, press the [Preset 8 In the [FM Timing] group, set the start position and
Color Mix] button and set the parameters. stop position of the frame memory video.
For details, see “Setting a Preset Color Mix” To set the start position
(page 59). Set using any of the following methods.
When [Wipe] is selected, press the [Wipe>Main • Move the fader lever to the start position and press
Pattern] button to open the Home > M/E-1 > Bus/ the [Set Start] button.
Transition > Wipe > Main Pattern menu (11109.31) • Press the button on the right side of the [Set Start]
and select a wipe pattern. button and enter a start position in the numeric
keypad window (number of frames).
For details, see “Setting a Wipe” (page 99).
To set the stop position
When [DME Wipe] is selected, press the [DME Set using any of the following methods.
Wipe>1ch Pattern] button to open the Home > M/E-1 • Move the fader lever to the stop position and press
> Bus/Transition > DME Wipe > 1ch Pattern menu the [Set Stop] button.
(11109.41) and select a DME wipe pattern. • Press the button on the right side of the [Set Stop]
To use a DME wipe pattern in 2-channel mode, open button and enter a stop position in the numeric
the Home > M/E-1 > Bus/Transition > DME Wipe > keypad window (number of frames).
2ch Pattern menu (11109.42) and select a DME wipe
124
To reset the start position and stop position
Press the [Reset Timing] button.
Note
The priority options available for selection vary
depending on the number of keys assigned to a
switcher bank.
125
Frame Memory Chapter
126
Still image content: Freeze a point in the input signal and Audio content:
save as a still image. Each frame memory contains • WAV (PCM) file
single still image content. 32 kHz/44.1 kHz/48 kHz, 16-bit/24-bit
Video content: Specify a start point and stop point in the • M4A (AAC) file
input signal, and save as video content. Each video 32 kHz/44.1 kHz/48 kHz
content is composed by a continuous series of still
images. The collection of still images creating the
video content are referred to as a series of still images.
Combined content
Content is managed using the Home > Content menu. Content that combines two still image content resources or
two video content resources is called combined content.
For details, see “Chapter 20 Content Management” You can combine two still image content resources (such
(page 270). as a video signal and key signal) or two video content
resources with the same duration.
Notes on saving or recalling a frame memory in a When group mode is enabled and combined content is
snapshot or effect timeline selected, content 1 and content 2 of the combined content
• Only still image content and video content recalled on are recalled on the two combined frame memory output
frame memory output channels (FM1 to FM16) can be channels, respectively.
the target for snapshots or effect timelines.
• To recall a frame memory using a snapshot or effect For details, see “Combining Content” (page 276).
timeline, the still image content and video content must
exist in frame memory in the same condition as when it Audio playback
was saved. Load the target content in frame memory
beforehand so that it is available for use when the recall In video content, audio is recorded in addition to the video.
operation occurs. You can play recorded audio using normal video content
playback. You can also play audio while recording video
content to monitor the audio.
Supported formats To play audio, first enable audio on the target frame
Frame memory supports content in the following file memory output channel for operation.
formats.
Notes
Note • Audio is recorded in video content, even if the video
Operation is not guaranteed for all content in the following content is created with audio disabled on a frame
file formats. memory output channel. Audio recording cannot be
disabled.
Still image content: • To play audio, set the signal output to through mode.
• TIFF file For details about through mode, see “Setting Through
• BMP file Mode” (page 297).
• TARGA file • The AUX bus and edit preview bus are the only buses
• PNG file that can output audio.
• Frame memory dedicated still image file • In variable-speed playback, audio is not played.
• In loop playback, audio fades in at the playback start
Video content: point and fades out at the playback stop point. In reverse
• MOV file playback, audio is not played.
Video: MPEG-4 AVC/H.264, 4:2:0/4:2:2 8-bit/10-bit • Noise may occur if a frame memory source bus or frame
Audio: AAC or PCM, 32 kHz/44.1 kHz/48 kHz, 16-bit/ memory output cross-point is switched during audio
24-bit playback.
• MP4 file • The audio sampling frequency when recording audio is
Video: MPEG-4 AVC/H.264, 4:2:0/4:2:2 8-bit/10-bit 48 kHz only.
Audio: AAC or PCM, 32 kHz/44.1 kHz/48 kHz, 16-bit/
24-bit Importing/exporting
• Frame memory series of still images
Frame memory content can be imported from a computer
using the Home > Content > Import/Export menu. You can
Note
also export multiple content together as an archive file and
MOV files and MP4 files may not be displayed correctly, import an exported archive file into content storage.
depending on the content.
For details, see “Importing/Exporting Content” (page 278).
127
• Status icon
Frame Memory Icon Status
Through output
Assigning a Frame Memory Output
Still image recall output
To output frame memory images to a monitor, for
example, the output signals from frame memory (FM1 to
FM16) must be assigned to cross-point buttons Video playback
beforehand.
Video reverse playback
For details about assignment, see “Creating a Cross-
Point Assign Table” (page 301).
Video stopped
You can use the frame memory source 1 bus or 2 bus signal
for the input to frame memory. Audio enabled
Select a signal in a cross-point button row assigned with
the frame memory source 1 bus or 2 bus. Audio disabled
Selecting a Frame Memory Output A thumbnail and content information are displayed in the
content properties.
Channel
For details, see “Properties display” (page 272).
Displaying the frame memory output
channel status Selecting a frame memory output channel
Open the Home > Frame Memory > FM Common > Use the menu for the target frame memory output channel
Channel > Status menu (13109.31). for operation.
The status of the frame memory output channels is shown When frame memory output channel 1 (FM1) or frame
on the left, and the properties of the content recalled on the memory output channel 2 (FM2) is selected, open the
selected frame memory output channel are shown on the following menu.
right. To recall still image content or video content:
The following information is displayed in the frame Open the Home > Frame Memory > FM1/FM2 > Clip/
memory output channel status. Still > Recall menu (13101.11).
• Frame memory output channel The odd-numbered frame memory output channel
For combined channels, this is displayed in odd- (FM1) is shown on the upper left, and the even-
numbered channel/even-numbered channel format. numbered frame memory output channel (FM2) is
• Recalled content thumbnail shown on the lower left. Content can be displayed in
“No Thumbnail” is displayed if there is no thumbnail for list view or thumbnail view on the right.
the content. For combined channels, the combined frame memory
• Name of recalled content output channels (FM1/FM2) are shown on the left.
To play video content:
Open the Home > Frame Memory > FM1/FM2 > Clip/
Still > Play menu (13101.12).
Information and operation buttons for the odd-
numbered frame memory output channel (FM1) are
shown at the top, and information and operation
128
buttons for the even-numbered frame memory output combined and content 2 corresponding to the
channel (FM2) are shown at the bottom. combined content on FM1 is recalled on FM2.
For combined channels, information and operation - If content 1 of combined content is recalled on FM1
buttons for the combined frame memory output and other content is recalled on FM2, a message
channels (FM1/FM2) are shown. appears. If you press [OK], the content recalled on
To create still image content or video content: FM2 is released, the channels are combined and
Open the Home > Frame Memory > FM1/FM2 > Clip/ content 2 corresponding to the combined content on
Still > Record menu (13101.13). FM1 is recalled on FM2.
Information and operation buttons for the odd- - In all other cases, when content is recalled on FM1 or
numbered frame memory output channel (FM1) are FM2, a message appears. If you press [OK], the
shown at the top, and information and operation recalled content is released, the channels are
buttons for the even-numbered frame memory output combined, and both FM1 and FM2 become black
channel (FM2) are shown at the bottom. signals.
For combined channels, information and operation • If group mode is disabled while combined content is
buttons for the combined frame memory output recalled on FM1 and FM2, a message appears. If you
channels (FM1/FM2) are shown. press [OK], the channels are uncombined, content 1 of
the combined content remains recalled on FM1, content
2 recalled on FM2 is released, and FM2 becomes a black
Combining frame memory output channels signal.
Enable group mode.
This section describes combining FM1 and FM2 as an
example. Locking a frame memory output channel
You can lock a frame memory output channel when still
1 Open the Home > Frame Memory > FM Common > image content or video content is recalled on the frame
Channel > Config menu (13109.32). memory output channel.
The following operations are inhibited on a locked frame
The combine status is displayed for each frame memory output channel.
memory output channel. • Recalling content
• Creating content (freeze, record)
2 Set the [ ] button between [FM1] and [FM2] to the • Enabling/disabling audio
on state. The following operations are inhibited for content recalled
Group mode becomes enabled, FM1 and FM2 output on a locked frame memory output channel.
channels are combined, and a blue frame appears. The • Trimming video content
frame memory output channel display changes to • Unloading content
[FM1/FM2]. • Deleting content
To uncombine, set the [ ] button to the off state. To lock FM1, set the [Output Lock] switch for [FM1] to
the on state in the following menus.
To enable group mode using the frame memory • Home > Frame Memory > FM1/FM2 > Clip/Still >
output channel menu Recall menu (13101.11)
Set the [Group Mode] button to the on state in the • Home > Frame Memory > FM1/FM2 > Clip/Still > Play
following menus. menu (13101.12)
• Home > Frame Memory > FM1/FM2 > Clip/Still > • Home > Frame Memory > FM1/FM2 > Clip/Still >
Recall menu (13101.11) Record menu (13101.13)
• Home > Frame Memory > FM1/FM2 > Clip/Still >
Record menu (13101.13)
Frame Memory Content Operations
Notes
• Channels cannot be combined/uncombined in the For details about displaying and selecting content, see
following cases. “Content Operations” (page 271).
- When channels are locked
- When playing video Loading content
- When recording video or freezing a still image
• If group mode is enabled while content is recalled on a You can load content into frame memory from content
frame memory output channel, the following occurs. storage.
- If content 1 of combined content is recalled on FM1
and no content is recalled on FM2, the channels are
129
Notes Saving content to content storage
You can save content that is present only in frame memory
• Only video content with a frame rate the same as the
to content storage.
system frequency or a frame rate half the system
frequency can be loaded.
• If the system signal format is different than the image
1 Open the Home > Frame Memory > FM Common >
Load/Save > Save menu (13109.22).
size, the following processing occurs with the origin at
the top left of the image. Content can be displayed in list view or thumbnail
- If an image size is smaller, the missing part is filled view.
with black.
- If an image size is larger, the excess part is cropped 2 Select content to save.
and removed.
Even when image size processing occurs, the thumbnail To select and save multiple content, place a check
image is not changed. mark beside the target content to save.
To select and save all displayed content, place a check
1 Open the Home > Frame Memory > FM Common > mark in the Select All checkbox.
Load/Save > Load menu (13109.21).
3 Press the [Save to Storage] button.
Content can be displayed in list view or thumbnail
view. 4 Check the message, then press [OK].
130
3 Press the [Name] button and enter a content name (up
to 64 characters) using the keyboard.
Still Image Operations
4 Select a save destination folder in [Folder].
To create a folder This section describes the operation on frame memory
Press the [New Folder] button, enter a folder name (up output channel 1 (FM1) as an example.
to 32 characters) in the [New Folder] window, and
press [OK].
The folder is created within the selected folder. Creating a Still Image (Freeze)
Note You can assign a frame memory source bus signal to a
frame memory output channel and then execute a freeze to
The created folder hierarchy can have up to five levels capture still image content and save it in frame memory.
below the root.
Note
5 Press the [Duration] button and set the video content
duration in the numeric keypad window. When the system is powered off, the content in frame
memory will be lost. Save any required content in content
When set to “0”, video content recording continues storage.
until the free capacity in frame memory has been
consumed. For details, see “Saving content to content storage”
(page 130).
6 Select tags to add to content in [Tags].
Place a check mark for each tag to add. 1 Open the Home > Frame Memory > FM1/FM2 > Clip/
Still > Record menu (13101.13).
To create a tag
Press the [New Tag] button, enter a tag name (up to 24 To enable group mode
characters) in the [New Tag] window, and press [OK]. Set the [Group Mode] button to the on state.
When group mode is enabled, the frame memory
output channel display changes to [FM1/FM2].
Note
Up to five tags can be added to content created in 2 Set the [Through] button for [FM1] to the on state.
frame memory.
The frame memory source bus signal is output on the
7 Press [OK]. frame memory output channel.
131
The frame memory output channels are shown on the
left.
Video Operations
To enable group mode
Set the [Group Mode] button to the on state.
When group mode is enabled, the frame memory This section describes the operation on frame memory
output channel display changes to [FM1/FM2]. output channel 1 (FM1) as an example.
2 Select [FM1].
Creating Video (Record)
3 Select content to recall.
You can assign a frame memory source bus signal to a
The selected content is recalled and displayed on the frame memory output channel and then record to capture
frame memory output channel. video content and save it in frame memory.
Note Note
When group mode is disabled for frame memory When the system is powered off, the content in frame
output channels and combined content is selected, memory will be lost. Save any required content in content
only content 1 of the combined content is recalled on storage.
frame memory output channel 1.
For details, see “Saving content to content storage”
(page 130).
1 Open the Home > Frame Memory > FM1/FM2 > Clip/
Still > Record menu (13101.13).
To enable group mode
Set the [Group Mode] button to the on state.
When group mode is enabled, the frame memory
output channel display changes to [FM1/FM2].
Note
The output signal of the frame memory output channel
is delayed by one frame.
Note
If a frame memory is recalled using a snapshot while
video is being recorded, the recording stops.
132
To play audio during recording When group mode is enabled, the frame memory
Set the [Audio On] switch for [FM1] to the on state. output channel display changes to [FM1/FM2].
To enable V/K mode 2 Control the video using the operation buttons for
Set the [V/K Mode] button to the on state. [FM1].
Video playback operations
Recalling Video
a b c d
1 Open the Home > Frame Memory > FM1/FM2 > Clip/
Still > Recall menu (13101.11).
Content can be displayed in list view or thumbnail
view.
The frame memory output channels are shown on the
left.
To enable group mode
Set the [Group Mode] button to the on state.
e f g
When group mode is enabled, the frame memory
output channel display changes to [FM1/FM2].
a Playback start point
2 Select [FM1]. You can enter a playback start point in the numeric keypad
window.
3 Select content to recall.
b Current playback position
The selected content is recalled and displayed on the You can enter a playback position in the numeric keypad
frame memory output channel. window to move to that position.
To set the playback position, set the following parameter.
Note
No. Parameter Adjustment
When group mode is disabled for frame memory
output channels and combined content is selected, 1 FM1 Current Current playback position
only content 1 of the combined content is recalled on
frame memory output channel 1. c Repeat (loop) playback
When repeat playback is set, a loop or ping-pong icon and
the number of repetitions are displayed.
Playing Video d Playback stop point
You can enter a playback stop point in the numeric keypad
Playback of video content recalled on a frame memory
window.
output channel can be controlled using the menu or device
control block.
e Start of video content
1 Open the Home > Frame Memory > FM1/FM2 > Clip/
Still > Play menu (13101.12).
133
Button Operation Note
Playback
When the [Variable Speed] button is set to the on state,
audio is not played.
Move to video playback stop point
To delete regions outside the playback range
(trimming)
Move to end of video content Press the [Trim] button, check the message, then press
[OK].
The region before the set playback start point and the
Set current position as playback start point
region after the set playback stop point are deleted.
No. Parameter Adjustment The [PLAY] button is lit amber, and playback starts.
To stop playback, press the [STOP], [SHTL], [JOG],
2 FM1 Speed Playback speed (0% to 200%)
[CUE], [REW], [FF], or [ALL STOP] button.
134
Video playback operations
Operate using the following buttons.
Button Operation
FM LOOP Repeat (loop) playback
START TC Set current position as playback start point
STOP TC Set current position as playback stop point
STOP Pause playback
CUE Move to video playback start point
REW Move to start of video content
PLAY Playback
FF Move to end of video content
VAR Variable-speed playback in variable mode.
JOG Variable-speed playback in jog mode.
SHTL Variable-speed playback in shuttle mode.
ALL STOP All stopped
135
Clip Player Chapter
Note MOV files and MP4 files may not be displayed correctly,
depending on the content.
When the system signal format is 2160P, only two
channels comprising Clip 1 and Clip 2 can be used. Audio content:
• WAV (PCM) file
Group mode (combine channels) 32 kHz/44.1 kHz/48 kHz, 16-bit/24-bit
• M4A (AAC) file
When group mode is enabled on consecutive odd- 32 kHz/44.1 kHz/48 kHz
numbered and even-numbered clip player output channels,
the two channels are combined.
Clip player operations control the combined clip player Combined content
output channels. Content that combines two video content resources is
When combined content is selected, content 1 and content called combined content.
2 of the combined content are recalled on the two You can combine two video content resources with the
combined clip player output channels, respectively. same duration.
136
When group mode is enabled and combined content is
selected, content 1 and content 2 of the combined content
are recalled on the two combined clip player output
Clip Player Operations
channels, respectively.
For details, see “Combining Content” (page 276). Assigning Clip Player Outputs
To output clip player images to a monitor, for example, the
Audio playback
output signals from the clip player (CLIP1 to CLIP4) must
You can play audio using normal video content playback. be assigned to cross-point buttons beforehand.
To play audio, first enable audio on the target clip player
output channel for operation. For details about assignment, see “Creating a Cross-
Point Assign Table” (page 301).
Notes
• To play audio, set the signal output to through mode.
For details about through mode, see “Setting Through Selecting a Clip Player Output
Mode” (page 297). Channel
• The AUX bus and edit preview bus are the only buses
that can output audio.
• In loop playback, audio fades in at the playback start Displaying the clip player output channel
point and fades out at the playback stop point. status
• In variable-speed playback, audio is not played. Open the Home > Clip Player > Clip Common > Channel
• Noise may occur if a clip player output cross-point is > Status menu (14103.31).
switched during audio playback. The status of the clip player output channels is shown on
the left, and the properties of the content recalled on the
Importing/exporting selected clip player output channel are shown on the right.
The following information is displayed in the clip player
Clip player content can be imported from a computer using
output channel status.
the Home > Content > Import/Export menu. You can also
• Clip player output channel
export multiple content together as an archive file and
For combined channels, this is displayed in odd-
import an exported archive file into content storage.
numbered channel/even-numbered channel format.
• Recalled content thumbnail
For details, see “Importing/Exporting Content”
“No Thumbnail” is displayed if there is no thumbnail for
(page 278).
the content.
• Name of recalled content
• Status icon
Icon Status
Black output
Video playback
Video stopped
Audio enabled
Audio disabled
Locked
137
For details, see “Properties display” (page 272). Notes
• Channels cannot be combined/uncombined in the
Selecting a clip player output channel following cases.
Use the menu for the target clip player output channel for - When channels are locked
operation. - When playing video
When clip player output channel 1 (Clip 1) or clip player • If group mode is enabled while content is recalled on a
output channel 2 (Clip 2) is selected, open the following clip player output channel, the following occurs.
menu. - If content 1 of combined content is recalled on Clip 1
To recall video content: and no content is recalled on Clip 2, the channels are
Open the Home > Clip Player > Clip1/Clip2 > Clip > combined and content 2 corresponding to the
Recall menu (14101.11). combined content on Clip 1 is recalled on Clip 2.
The odd-numbered clip player output channel (Clip 1) - If content 1 of combined content is recalled on Clip 1
is shown on the upper left, and the even-numbered clip and other content is recalled on Clip 2, a message
player output channel (Clip 2) is shown on the lower appears. If you press [OK], the content recalled on
left. Content can be displayed in list view or thumbnail Clip 2 is released, the channels are combined and
view on the right. content 2 corresponding to the combined content on
For combined channels, the combined clip player Clip 1 is recalled on Clip 2.
output channels (Clip 1/Clip 2) are shown on the left. - In all other cases, when content is recalled on Clip 1 or
To play video content: Clip 2, a message appears. If you press [OK], the
Home > Clip Player > Clip1/Clip2 > Clip > Play menu recalled content is released, the channels are
(14101.12). combined, and both Clip 1 and Clip 2 become black
Information and operation buttons for the odd- signals.
numbered clip player output channel (Clip 1) are • If group mode is disabled while combined content is
shown at the top, and information and operation recalled on Clip 1 and Clip 2, a message appears. If you
buttons for the even-numbered clip player output press [OK], the channels are uncombined, content 1 of
channel (Clip 2) are shown at the bottom. the combined content remains recalled on Clip 1, content
For combined channels, information and operation 2 recalled on Clip 2 is released, and Clip 2 becomes a
buttons for the combined clip player output channels black signal.
(Clip 1/Clip 2) are shown.
Locking clip player output channels
Combining clip player output channels You can lock a clip player output channel when video
Enable group mode. content is recalled on the clip player output channel.
This section describes combining Clip 1 and Clip 2 as an The following operations are inhibited on a locked clip
example. player output channel.
• Recalling content
1 Open the Home > Clip Player > Clip Common > • Enabling/disabling audio
Channel > Config menu (14103.32). The following operations are inhibited for content recalled
on a locked clip player output channel.
The combine status is displayed for each clip player • Unloading content
output channel. • Deleting content
To lock Clip 1, set the [Output Lock] switch for [Clip 1] to
2 Set the [ ] button between [Clip 1] and [Clip 2] to the the on state in the following menus.
on state. • Home > Clip Player > Clip1/Clip2 > Clip > Recall menu
Group mode becomes enabled, Clip 1 and Clip 2 (14101.11)
output channels are combined, and a blue frame • Home > Clip Player > Clip1/Clip2 > Clip > Play menu
appears. The clip player output channel display (14101.12)
changes to [Clip 1/Clip 2].
To uncombine, set the [ ] button to the off state.
To enable group mode using the clip player
Clip Player Content Operations
output channel menu
Set the [Group Mode] button to the on state in the Home > For details about displaying and selecting content, see
Clip Player > Clip1/Clip2 > Clip > Recall menu “Content Operations” (page 271).
(14101.11).
138
Loading content Editing content properties
You can load content into the clip player from content You can edit the properties of content in content storage.
storage. Press the [Edit Properties] button in the Home > Clip
Player > Clip Common > Load > Load menu (14103.21)
Notes and edit the properties in the [Edit Properties] window.
• Video content cannot be loaded if the image size is For details, see “Editing Content Properties” (page 275).
different from the system signal format.
• During playback, frames may be dropped or duplicated
if the frame rate of the video content is different from the
system frequency.
1 Open the Home > Clip Player > Clip Common > Load
> Load menu (14103.21).
Content can be displayed in list view or thumbnail
view.
Unloading content
You can unload content from the clip player.
1 Open the Home > Clip Player > Clip Common >
Browse Local menu (14103.11).
Content can be displayed in list view or thumbnail
view.
139
Playing video (menu)
Video Operations 1 Open the Home > Clip Player > Clip1/Clip2 > Clip >
Play menu (14101.12).
This section describes the operation on clip player output When group mode is enabled, the clip player output
channel 1 (Clip 1) as an example. channel display changes to [Clip 1/Clip 2].
140
Button Operation Playing video (device control block)
Pause playback The device control block can be switched to device/frame
memory/clip player operation mode for playback control
of video.
Playback
Note
Move to video playback stop point
The buttons used for selecting a clip player output channel
must be assigned to the operation buttons of the device
Move to end of video content control block beforehand.
Set current position as playback stop point 1 Press the [DEV] button.
The [DEV] button is lit amber, and the operation mode
switches to device/frame memory/clip player
g End of video content operation mode.
To play audio
Set the [Audio On] switch to the on state. 2 Press the [CP1] button.
To repeat playback (looping) The [CP1] button is lit green, and clip player output
channel 1 becomes the target of operations.
1 Press the [Set Loop Playback] button. When group mode is enabled, the buttons for the two
combined clip player output channels are lit.
The [Set Loop Playback] window appears.
3 Press the [PLAY] button.
2 In the [Loop Mode] group, set repeat playback.
The [PLAY] button is lit amber, and playback starts.
Off: Turns repeat playback off. To stop playback, press the [STOP], [CUE], [REW],
Loop: Loop playback. When the playback stop point [FF], or [ALL STOP] button.
is reached, playback continues from the playback
start point. Video playback operations
When the [Loop] button is selected, set the number of Operate using the following buttons.
repetitions in the [Repeat] group. Button Operation
Set the repetitions radio button to the on state, press the
FM LOOP Repeat (loop) playback
input field, and enter the number of repetitions in the
numeric keypad window. START TC Set current position as playback start
To repeat indefinitely, set the [Infinite Loop] radio point
button to the on state. STOP TC Set current position as playback stop
point
3 Press [OK]. STOP Pause playback
CUE Move to video playback start point
To change the playback speed
Set the [Variable Speed] button to the on state and set the REW Move to start of video content
following parameter. PLAY Playback
FF Move to end of video content
No. Parameter Adjustment
ALL STOP All stopped
2 Clip 1 Speed Playback speed (0% to 100%)
Note
When the [Variable Speed] button is set to the on state,
audio is not played.
141
DMEs
* The DME function is not supported in version 1.0.
Chapter 12
2160P format:
Overview Up to two channels
Maximum of one channel when DME channel 1 is set
to enhanced function mode.
1080P or 1080i format:
DME function Up to four channels
DME (Digital Multi Effects) allows you to add three- Maximum of three channels when DME channel 1 or
dimensional transforms such as image movement, 2 is set to enhanced function mode.
rotation, magnification and shrinking, as well as special Maximum of two channels when both DME channels
effects. 1 and 2 are set to enhanced function mode.
Multiple DME channels can be also combined, which
allows you to create complex and advanced effects.
To use the DME function, the following options are External input (Ext In)
required. The signal that is input on DME Ext In (AUX bus output)
• XKS-G1600 GPU Pack is set in the Home > Setup > Switcher > DME Interface
• XZS-G1610 3D DME License menu (19103.31) menu.
When the system signal format is 2160P, the DME
function must be enabled for use. For details about Ext In settings, see “Setting a DME
External Input (Ext In)” (page 311).
For details about setting GPU functions, see “Setting a
GPU” (page 286).
Three-Dimensional Transforms
Enhanced function mode
Depending on the DME effect, an enhanced function DME An operation that moves, rotates, or resizes an image in
may be required. three-dimensional space is called a three-dimensional
To use an enhanced function DME, set the DME channel transform.
to enhanced function mode.
When the system signal format is 2160P, only DME
channel 1 can be set to enhanced function mode. When the Three-dimensional space
system signal format is 1080P or 1080i, only DME
Source space and target space
channels 1 and 2 can be set to enhanced function mode.
Images are arranged in one of two types of space: source
When enhanced function mode is enabled, the number of
space and target space.
DME channels that can be used is reduced.
Source space: Three-dimensional space with the image as
reference
For details about setting enhanced function mode, see
The X- and Y-axes are defined along the plane of the
“Setting DME Channel Enhanced Function Mode”
image, and the Z-axis is defined perpendicular to the
(page 286).
plane of the image. When you move an image, the
coordinate axes also move.
DME channels Target space: Three-dimensional space with the monitor
The number of DME channels that can be used will vary, screen as reference
depending on the system signal format. The X- and Y-axes are defined as the horizontal and
vertical to the plane of the monitor screen, and the Z-
axis is defined perpendicular to the plane of the
142
monitor screen. The coordinate axes do not change Three-dimensional parameters
even if an image moves. Three-dimensional parameters have X, Y, and Z values
which define the position of an image, its axis of rotation,
the position of the virtual viewpoint of the image, and so
on.
On a 16:9 monitor screen, the reference values of
parameters for the image (source space) and screen (target
space) are as follows.
Center of image or screen:
Source space Target space
X = 0.00, Y = 0.00, Z = 0.00
Upper right corner of image or screen:
X = 16.00, Y = 9.00, Z = 0.00
Example: Lower left corner of image or screen:
Image moved in X-axis direction X = –16.00, Y = –9.00, Z = 0.00
The direction of movement differs as follows in source
space and target space. Y-axis
Z-axis +
+9.00
X-axis
–16.00
+16.00
X-axis
Local space and global space The Z-axis direction is + behind the image or screen,
There are two types of DME coordinate space: local space and – in front of the image or screen.
and global space.
Local space: Coordinates that are local to each DME Three-dimensional parameter setting values
channel The parameter value setting ranges and defaults are as
Global space: Coordinates that are common to all channels follows.
By switching from local space to global space, you can add
additional movement to the movement of images in Operation Setting range Default
individual channels, and also add transform effects to Move image –999.9999 to 0.0000
multiple channels that have been combined using global (Location XYZ) +999.9999
effects.
Rotate image –999.9999 to 0.0000
Example: (Rotation) (Spin) +999.9999
Rotation around Y-axis
Move rotation axis –999.9999 to 0.0000
(Axis Location) +999.9999
Rotation around Y-axis in local space
Scale image 0.0000 to 999.9999 1.0000
(Location Size)
Change image aspect 0.0000 to 2.0000 1.0000
ratio
(Aspect)
Change viewpoint –999.9999 to 0.0000
position +999.9999
(Perspective (X) (Y))
Change viewpoint 0.0000 to 999.9999 1.0000
position
(Perspective (Z))
Change image skew –9.9999 to +9.9999 0.0000
(Skew)
Rotation around Y-axis in global space
143
Detents Image movement in target space
In three-dimensional space, points called “detents” are
defined at regular intervals.
You can set the current three-dimensional parameter
values to the closest detent point.
The intervals between detents are defined as follows.
There are the following types of DME three-dimensional Image rotation in source space
transforms.
Movement in
Z-axis direction
144
Image rotation in target space Shrinking and magnifying an image in target space is a
conversion to a two-dimensional image for display on a
monitor screen, so shrinking and magnifying does not
change the shape of the image.
Scaling in source space
Movement in Movement in
X-axis direction Y-axis direction
Movement in
Z-axis direction
145
The X-axis and Y-axis values define the position of the Effect Description
viewpoint, and the Z-axis value defines the distance from
Crop Crop the top, bottom, left, and right of an
the viewpoint. image.
Wipe crop Display an image inside or outside a wipe
pattern.
Effect Description
Change viewpoint position Change viewpoint position
in X-axis direction in Y-axis direction Defocus Defocus an image.
Sepia Overlay a specified color onto an image.
Mono Convert an image to monochrome.
Mosaic Divide an image into small tiles.
Mask Mask part of an image so that effects are
applied to a selected portion.
Other settings
Change skew in
Background
X-axis direction Set the signal to insert into the background of an image.
Change skew in Invert
Y-axis direction Invert an image in the horizontal and vertical directions.
Separate Side
Set whether to insert different signals into the front and
Graphics Display back sides of the image.
This function allows you to display wire frames, Removing the Virtual Image
coordinate axes, and a grid over a DME image. This is When the perspective of an image is changed, this sets the
useful when checking or modifying an image in three- portions beyond the virtual viewpoint displayed on the
dimensional space. monitor screen (virtual image) so that they are not
displayed.
For details, see “Graphics Display” (page 151).
Key Density
Set the key density.
DME Effects Key Source
Set the key source signal used for the images on the front
The following DME effects can be configured. and back sides.
Interpolation processing
Edge effects Set the number of pixels and the anti-aliasing mode used
for interpolation processing.
Effect Description
Border Add a border to an image.
146
Global Effects
Three-Dimensional
Global effects are effects created by combining multiple
consecutive DME channels. Transforms
The following global effects can be configured.
Three-Dimensional Transform
Operations (Device Control Block)
Button Description
LOCAL Enable local space operations.
Can be selected at the same time as the
[GLB] button.
GLB Enable global space operations.
Can be selected at the same time as the
[LOCAL] button.
SRC Enable source space operations.
Cannot be selected at the same time as the
[TRGT] button.
147
Button Description Button Description
TRGT Enable target space operations. X Restricts the parameters targeted by the
Cannot be selected at the same time as the Y operation.
[SRC] button. Z You can select multiple buttons.
When the [X] button is lit:
ASP PERS • When the [ASP PERS] button is pressed
Operations on parameters on the X-axis
in source space: using the trackball are enabled.
Adjusts the aspect ratio of an image in the When the [Y] button is lit:
X-axis or Y-axis direction using the Operations on parameters on the Y-axis
trackball, or in both the X-axis and Y-axis using the trackball are enabled.
directions simultaneously using the Z-ring. When the [Z] button is lit:
• When the [ASP PERS] button is pressed Operations on parameters on the Z-axis (Z-
while pressing the [SHIFT] button in ring adjustment items) using the Z-ring are
source space: enabled.
Adjusts the skew of an image in the X-axis FINE Switches to fine mode, enabling fine
or Y-axis direction using the trackball. adjustment control of setting values using
• When the [ASP PERS] button is pressed the trackball and Z-ring.
in target space: CTR • When the [CTR] button is pressed once:
Adjusts the viewpoint position (perspective Adjusts the three-dimensional transform
of an image) in the X-axis or Y-axis parameters to the detent positions.
direction using the trackball. • When the [CTR] button is pressed twice,
Adjusts the distance from the viewpoint or the [CTR] button is pressed once while
position using the Z-ring. pressing the [SHIFT] button:
LOC SIZE Moves an image in the X-axis or Y-axis Returns the three-dimensional transform
direction using the trackball. parameters to the default values.
Scales an image (shrink/magnify) using the
Z-ring. Trackball and Z-ring operations
LOC XYZ Moves an image in the X-axis or Y-axis Operation in the X-axis direction:
direction using the trackball, and in the Z- Turn the trackball horizontally.
axis direction using the Z-ring. Parameter values increase as you turn to the right, and
ROT • When the [ROT] button is pressed: decrease as you turn to the left.
Rotates an image around the X-axis or Y-
axis using the trackball, and around the Z-
axis using the Z-ring.
• When the [ROT] button is pressed while
pressing the [SHIFT] button:
Rotates the image in spin mode.
SHIFT Used in combination with the [ASP PERS],
[ROT], [CTR], and [CLR WORK BUFR]
buttons.
CLR WORK • When the [CLR WORK BUFR] button is Operation in the Y-axis direction:
BUFR pressed once: Turn the trackball vertically.
Returns the three-dimensional transform Parameter values increase as you turn upward, and
parameters to the initial settings. decrease as you turn downward.
• When the [CLR WORK BUFR] button is
pressed twice, or the [CLR WORK BUFR]
button is pressed once while pressing the
[SHIFT] button:
Returns all DME parameters to the initial
settings.
AXIS LOC Moves the rotation axis of an image in the X-
axis or Y-axis direction using the trackball,
and in the Z-axis direction using the Z-ring.
Operation in the Z-axis direction:
Turn the Z-ring.
Parameter values increase as you turn clockwise, and
decrease as you turn counterclockwise.
However, if you have pressed the [LOC XYZ] button or
[AXIS LOC] button, the parameter values decrease as you
turn clockwise, and increase as you turn counterclockwise.
148
The [DME] button is lit amber, and the device control
block switches to three-dimensional transform
operation mode.
149
For details about initial status, see “Setting Startup” the 1st page and the parameter buttons for global space
(page 282). are displayed on the 2nd page. Set the parameters for
local space on the 1st page and the parameters for
To return three-dimensional parameters to the initial global space on the 2nd page.
settings:
Press the [CLR WORK BUFR] button once. Configurable three-dimensional parameters
To return all DME parameters to the initial settings: The parameters that can be set vary depending on the
Press the [CLR WORK BUFR] button twice. Or press three-dimensional transform operation buttons.
and hold the [SHIFT] button and press the [CLR Location Size: Scale image (shrink/magnify)
WORK BUFR] button. Only the Z-axis in source space can be configured.
All axes in target space can be configured.
Location XYZ: Move image
All axes can be configured.
Three-Dimensional Transform Rotation: Rotate image (rotation mode)
Operations (Menu) All axes can be configured.
Spin: Rotate image (spin mode)
This section describes the menu for DME channel 1 as an All axes can be configured.
example. Aspect: Change image aspect ratio
Only the source space of the local space can be
configured.
Adjusting three-dimensional parameters
Skew: Change image skew
Only the X-axis and Y-axis in the source space of the
1 Open the Home > DME > Channel1 > 3D Transform
local space can be configured.
> Adjust menu (15101.11).
Perspective: Change viewpoint position
Only target space can be configured.
2 In the [Local/Global] group, select local space or
Axis Location: Move rotation axis
global space.
Only source space can be configured.
Local: Local space
To change parameters to the closest detent
Global: Global space
position
Both local space and global space can be selected.
Press the [Detents] button.
3 In the [Source/Target] group, select source space or
For details about detents, see “Detents” (page 144).
target space.
Source: Source space To return parameters to the initial settings
Target: Target space The parameters return to the initial status saved data
Either source space or target space can be selected. setting values.
The operation must be performed separately for global
4 Set the target three-dimensional transform operation space and local space.
X-axis, Y-axis, and Z-axis parameters.
For details about initial status, see “Setting Startup”
When local space is selected (page 282).
Press the [X] button, [Y] button, or [Z] button for
[Local], and enter a setting value in the numeric To return three-dimensional parameters to the initial
keypad window. settings:
Press the [Clear 3D Parameter] button.
When global space is selected
To return all DME parameters to the initial settings:
Press the [X] button, [Y] button, or [Z] button for
Press the [Clear All Parameters] button.
[Global], and enter a setting value in the numeric
keypad window.
To adjust parameters using the analog controls
section
Press the button for the target three-dimensional
transform operation to set, and set the [X] parameter,
[Y] parameter, and [Z] parameter in the analog
controls section.
When both local space and global space are selected,
the parameter buttons for local space are displayed on
150
Graphics Display
Overview
This function allows you to display wire frames,
coordinate axes, and a grid over a DME image.
You can configure the following kinds of graphics.
Wire frame
Places a wire frame around the image. This allows you to
check the position and size of the image. Scale (reduced display)
The size is reduced to display the range that is not
Note displayed on the normal monitor screen. This allows you
When a Shadow global effect is set, a shadow frame is to check the position of an image in a larger space. The
displayed. range displayed on a normal monitor screen is indicated by
a frame.
Coordinate axes
Displays three-dimensional coordinates in local space or Wire frame
global space. This allows you to check the origin and the
directions of the X-axis, Y-axis, and Z-axis.
Channel ID
Displays the channel number. This allows you to check the
channel being used.
Channel IDs are displayed differently in local space and
global space.
Local space: The channel number is displayed along with
“F” (Front) or “B” (Back) indicating the side of the
wire frame. For example, “1F” indicates that channel
1 is being used at the front in local space.
Global space: The channel number is displayed along with Range displayed on
“G” (Global) to indicate global space. For example, normal monitor screen
“G2” indicates that channel 2 is being used in global
space.
Automatically erasing the graphics display
This automatically erases the graphics display when an
Local space coordinate axes
effect timeline is executed. You can set the timing for
when to redisplay graphics after the effect timeline has
completed.
Setting a Graphic
This section describes the menu for DME channel 1 as an
example.
1 Open the Home > DME > Channel1 > Input/Output >
Channel ID Graphic menu (15101.04).
Wire frame
2 Set the [Graphic] button to the on state.
151
Ch ID: Channel ID
Wire Frame: Wire frame
Grid: Grid
Edge Effects
To reduce the display size of graphics display
Set the [Scale] button to the on state and set the following This section describes the menu for DME channel 1 as an
parameter. example.
152
Setting a Crop Setting a Wipe Crop
1 Open the Home > DME > Channel1 > Edge > Border/ Note
Crop menu (15101.21).
When Brick is set, Wipe Crop cannot be enabled.
2 Set the [Crop] button to the on state and set the
following parameters. 1 Open the Home > DME > Channel1 > Edge > Wipe
Crop menu (15101.22).
No. Parameter Adjustment 2 Set the [Wipe Crop] button to the on state.
1-1 H Simultaneous adjustment of
crop of left and right edges a) 3 Press the [Pattern Select] button.
1-2 V Simultaneous adjustment of
crop of top and bottom edges A pattern selection window appears.
a)
1-3 All Simultaneous adjustment of 4 Set the button for the target wipe crop pattern to the on
crop of top, bottom, left, and state.
right edges a)
2-1 Top Crop of top edge Note
2-2 Left Crop of left edge The wipe crop patterns are the same as wipe pattern
2-3 Right Crop of right edge numbers 1 to 24 and 304.
2-4 Bottom Crop of bottom edge
5 Press [OK].
a) The entered numeric value is automatically a positive value for the
right and top edges and a negative value for the left and bottom edges. To invert the wipe crop area (Invert)
To soften the edges You can swap the inner and outer areas of the wipe crop
Set the [Edge Soft] button to the on state and set the pattern.
following parameter. Set the [Invert] button to the on state.
153
To set the wipe crop pattern position and size
(Position/Size) No. Parameter Adjustment
Set the [Position/Size] button to the on state and set the 1 Amplitude Amplitude of modulation
following parameters. 2 Frequency Frequency of modulation
No. Parameter Adjustment 3 Speed Speed of ripples
• Negative values create waves
1 H Horizontal position in the down and left directions.
2 V Vertical position • Positive values create waves in
the up and right directions.
3 Size Pattern size
5 Pattern Pattern number (1 to 24, 304) To modify a wipe crop pattern edge (Edge)
To set the aspect ratio of a wipe crop pattern 1 In the [Edge] group, select a type of edge.
(Aspect)
Set the [Aspect] button to the on state and set the following Border: Adds a border to a pattern.
parameter. Soft: Softens the edges of a pattern.
Soft Border: Softens a border applied to a pattern.
No. Parameter Adjustment When the [Border] button is selected, set the following
1 Aspect Aspect ratio parameter.
• Negative values expand
vertically. No. Parameter Adjustment
• Positive values expand 1 Width Border width
horizontally.
When the [Soft] button is selected, set the following
To rotate a wipe crop pattern (Rotation) parameter.
In the [Rotation] group, select a rotation type.
Angle: Incline a pattern at a fixed angle. No. Parameter Adjustment
Speed: Rotate a pattern at a fixed speed. 1 Soft Edge softness
When the [Angle] button is selected, set the following
parameter. When the [Soft Border] button is selected, set the
following parameters.
No. Parameter Adjustment
1 Angle Inclination angle of pattern No. Parameter Adjustment
• A value of –1.00 corresponds to 1 Width Border width
a rotation of one turn
counterclockwise. 2 Inner Soft Softness of inner edge of
border
• A value of +1.00 corresponds to
a rotation of one turn clockwise. 3 Outer Soft Softness of outer edge of
• A value of 0.00 corresponds to border
no rotation.
2 In the [Border Fill] group, select a signal to insert in
When the [Speed] button is selected, set the following the border.
parameter.
Flat Color: Single color
No. Parameter Adjustment Ext Video: External input (Ext In) signal
1 Speed Rotation speed of pattern When the [Flat Color] button is selected, set the
• A value of –100.00 corresponds following parameters.
to 4 revolutions/second
counterclockwise rotation. No. Parameter Adjustment
• A value of +100.00 corresponds 1 Luminance Luminance
to 4 revolutions/second
clockwise rotation. 2 Saturation Saturation
• A value of 0.00 corresponds to 3 Hue Hue
no rotation (stationary).
154
No. Parameter Adjustment
Video Modifier Effects 3 Mix All Simultaneous adjustment of
luminance signal and
chrominance signal mix
amounts
This section describes the menu for DME channel 1 as an
example.
3 Press the [Sepia Color] button and set the sepia color
using the following parameters.
Setting Defocus
No. Parameter Adjustment
1 Luminance Luminance
Note
2 Saturation Saturation
To use the Defocus effect, the DME channel must be set to 3 Hue Hue
enhanced function mode.
1 Open the Home > DME > Channel1 > Video Modify
> Defocus menu (15101.31). Setting Mono
2 Set the [Defocus] button to the on state and set the Note
following parameters.
Enabling Mono disables Sepia if it is set.
No. Parameter Adjustment 1 Open the Home > DME > Channel1 > Video Modify
1 H Defocusing in horizontal > Color Modify menu (15101.32).
direction
2 V Defocusing in vertical direction 2 Set the [Mono] button to the on state.
3 All Simultaneous defocusing
adjustment in horizontal
direction and vertical direction
Setting a Mosaic
3 In the [Defocus Mode] group, select a signal to which
1 Open the Home > DME > Channel1 > Video Modify
to apply the Defocus effect.
> Mosaic menu (15101.33).
Video/Key: Video signal and key signal
Video: Video signal only 2 Set the [Mosaic] button to the on state and set the
following parameters.
To remove the black level leakage that occurs at
the edges of the screen
Set the [Clean Defocus] button to the on state. No. Parameter Adjustment
1 Size Tile size
2 Aspect Tile aspect ratio
Setting Sepia • Negative values expand
vertically.
• Positive values expand
Note horizontally.
1 Open the Home > DME > Channel1 > Video Modify Setting a Mask
> Color Modify menu (15101.32).
You can mask out part of a Defocus, Sepia, Mono, or
2 Set the [Sepia] button to the on state and set the Mosaic effect.
following parameters. Separate masks can be set for group 1 effects (Sepia,
Mono, Mosaic) and group 2 effects (Defocus).
No. Parameter Adjustment
1 Mix Y Luminance signal mix amount
2 Mix C Chrominance signal mix
amount
155
Note No. Parameter Adjustment
If a border has been set and then masks are enabled on both 1 Speed Rotation speed of pattern
group 1 effects and group 2 effects, the Border effect will • A value of –100.00 corresponds
also be masked. to 4 revolutions/second
counterclockwise rotation.
1 Open the Home > DME > Channel1 > Video Modify • A value of +100.00 corresponds
to 4 revolutions/second
> Mask menu (15101.34).
clockwise rotation.
• A value of 0.00 corresponds to
2 In [Effect Group], set the [Mask] switch for the target no rotation (stationary).
effect to the on state.
To invert a mask area
Group 1: Sepia, Mono, and Mosaic effects Set the [Invert] button to the on state.
Group 2: Defocus effect
Note
The mask patterns are the same as wipe pattern
numbers 21, 24, and 304.
To set the aspect ratio of a mask pattern (Aspect)
Press the [Aspect] button and set the following parameter.
156
Freeze Effects Nonlinear Effects
The following three types of freeze effects can be set. It is not possible to apply two or more nonlinear effects at
Hard freeze: Generate a still image at an arbitrary position. the same time. Enabling an effect automatically disables
Time strobe: Generate still images at fixed intervals. the previously enabled effect.
Film: Generate frames like in movie films. This section describes the menu for DME channel 1 as an
This section describes the menu for DME channel 1 as an example.
example.
To split an image
In the [Split Mode] group, select a type of split.
H&V: Split horizontally and vertically (top, bottom, left,
right)
H: Split horizontally (left, right)
V: Split vertically (top, bottom)
To select a signal to insert on the back side of the
page
In the [Back Video] group, select a signal.
Self: Same signal as the front side
Flat: Single color
Hue Rotation: Gradually varying hue
2nd Channel: 2nd channel signal
157
When the [Flat] button is selected, set the following
parameters. No. Parameter Adjustment
1 Luminance Luminance
No. Parameter Adjustment
2 Saturation Saturation
1 Luminance Luminance
3 Hue Hue
2 Saturation Saturation
3 Hue Hue When the [Hue Rotation] button is selected, set the
following parameters.
When the [Hue Rotation] button is selected, set the
following parameters. No. Parameter Adjustment
1 Luminance Luminance
No. Parameter Adjustment
2 Saturation Saturation
1 Luminance Luminance
3 Speed Speed at which the hue changes
2 Saturation Saturation
3 Speed Speed at which the hue changes Note
To set a 2nd channel signal, a DME channel for the second
Note
channel must be selected beforehand.
To set a 2nd channel signal, a DME channel for the second
channel must be selected beforehand. For details about selecting a DME channel, see “DME
Effects for Keys” (page 86).
For details about selecting a DME channel, see “DME
Effects for Keys” (page 86).
Setting a Roll
In the Home > DME > Channel1 > Non Linear > Effect
List menu (15101.51), press the [Roll] button to display
the Home > DME > Channel1 > Non Linear > Roll menu
(15101.53).
In the Home > DME > Channel1 > Non Linear > Roll
menu (15101.53), set the [Roll] button to the on state and
set the following parameters.
To split an image
In the [Split Mode] group, select a type of split.
H&V: Split horizontally and vertically (top, bottom, left,
right)
H: Split horizontally (left, right)
V: Split vertically (top, bottom)
To select a signal to insert on the back side of the
roll
In the [Back Video] group, select a signal.
Self: Same signal as the front side
Flat: Single color
Hue Rotation: Gradually varying hue
2nd Channel: 2nd channel signal
When the [Flat] button is selected, set the following
parameters.
158
1 Open the Home > DME > Channel1 > Input/Output >
Other Settings Video/Key menu (15101.02).
1 Open the Home > DME > Channel1 > Input/Output >
Video/Key menu (15101.02). Setting a Key Source Signal
2 In the [Front] group, select the direction of inversion You can select a key source signal used for the images on
for the image on the front side. the front and back sides.
H Invert: Invert horizontally. 1 Open the Home > DME > Channel1 > Input/Output >
V Invert: Invert vertically. Video/Key menu (15101.02).
3 In the [Back] group, select the direction of inversion 2 In the [Front Key] group, select a key source signal for
for the image on the back side. the image on the front side.
H Invert: Invert horizontally. Ext Key: Key signal sent from the switcher
V Invert: Invert vertically. Int Key: DME internal key signal
Linear Key: Luminance signal of the input video
signal
Setting Separate Sides When the [Linear Key] button is selected, set the
following parameters.
You can insert a different video signal/key signal into the
front and back sides of the image by enabling separate No. Parameter Adjustment
sides. 1 Clip Reference level for key signal
generation
159
No. Parameter Adjustment Mode3: Do not suppress aliasing when enlarging or
reducing the picture (sharp).
2 Gain Key gain
Note
Note
If a DME channel is assigned as the 1st channel or is
not assigned at all, only the [Ext Key] button can be
selected.
1 Open the Home > DME > Channel1 > Input/Output >
Process menu (15101.03).
Note
The [Multi] button can be selected only when the
DME channel is set to enhanced function mode.
160
Setting a Brick
Global Effects
Images selected on three DME channels can be combined
into a brick shape.
Overview
Global effects are effects created by combining multiple
consecutive DME channels.
The following global effects can be configured.
• Combiner
• Brick
• Shadow
The selected channels (Ch1 to Ch4) are assigned to the
surfaces of the brick as follows.
Setting a Combiner Channel Top side Side V Side H
Images selected on multiple DME channels can be Ch1 + Ch2 + Ch3 Ch1 Ch2 Ch3
combined automatically. You can set the order of priority Ch2 + Ch3 + Ch4 Ch2 Ch3 Ch4
(1 to 4) for combining images from up to four channels.
The selected channels (Ch1 to Ch4) are combined in the Note
following way in combiners 1 and 2.
When the system signal format is 2160P, Brick cannot be
Channel Combiner 1 Combiner 2 set.
Ch1 + Ch2 Ch1, Ch2 –
Ch2 + Ch3 Ch2, Ch3 –
1 Open the Home > DME > Global Effect > Brick menu
(15109.21).
Ch3 + Ch4 Ch3, Ch4 –
Ch1 + Ch2, Ch3 + Ch4 Ch1, Ch2 Ch3, Ch4 2 Set the [Brick] button to the on state and set the
Ch1 + Ch2 + Ch3 Ch1, Ch2, Ch3 – following parameters.
Ch2 + Ch3 + Ch4 Ch2, Ch3, Ch4 –
Ch1 + Ch2 + Ch3 + Ch4 Ch1, Ch2, Ch3, Ch4 – No. Parameter Adjustment
1 Height Height of brick
1 Open the Home > DME > Global Effect > Combiner 2 Front Overlap Front overlap
Priority menu (15109.11). 3 Side H Overlap Side H overlap
2 In the [Combiner 1 Priority] group, set the priority 4 Side V Overlap Side V overlap
order.
3 In the [Side H] group, select how to fit the image on
When combining two channels side H.
Set the channel buttons to the on state using [Priority
1] and [Priority 2]. Crop: Crop the parts that do not fit into the side
without shrinking the picture.
When combining three channels Compress: Reduce the image to fit.
Set the channel buttons to the on state using [Priority When the [Crop] button is selected, set the following
1] to [Priority 3]. parameters.
The position of the image set by the parameters is the
When combining four channels top left of side H. The bottom right is set
Set the channel buttons to the on state using [Priority automatically.
1] to [Priority 4].
No. Parameter Adjustment
When combining Ch1 + Ch2 and Ch3 + Ch4
In the [Combiner 1 Priority] group, set the priority order 1 H Position of left edge
for channels 1 and 2. In the [Combiner 2 Priority] group, 2 V Position of top edge
set the priority order for channels 3 and 4.
When the [Compress] button is selected, set the
following parameters.
The image with ranges set by the parameters is
enlarged/reduced to match the size of side H.
161
Channel Shadow setting
No. Parameter Adjustment
Ch1 Ch2 Ch3 Ch1 + Ch2 Ch2 + Ch3
1 Top Position of top edge
Ch1 + Ch2 + a a – a –
2 Left Position of left edge Ch3
3 Right Position of right edge Ch2 + Ch3 + – a a – a
4 Bottom Position of bottom edge Ch4
Ch1 + Ch2 + a a a a –
4 In the [Side H Rotation] group, set the angle of rotation Ch3 + Ch4
of the image on side H.
This section describes setting a shadow on channel 1 as an
0: No rotation example.
90: 90° rotation
180: 180° rotation 1 Open the Home > DME > Global Effect > Shadow
270: 270° rotation menu (15109.31).
5 In the [Side V] group, select how to fit the image on 2 Set the [Ch 1 Shadow] button to the on state and set the
side V. following parameters.
Configure in the same way as for side H.
No. Parameter Adjustment
6 In the [Side V Rotation] group, set the angle of rotation 1 Position H Shadow position in the
of the image on side V. horizontal direction
2 Position V Shadow position in the vertical
Configure in the same way as for side H. direction
To invert the image on the front side 3 Density Density of shadow
In the [Side H Front] group for side H or [Side V Front]
group for side V, select the direction of inversion. 3 In the [Ch 1 Shadow Source] group, select a signal to
Invert H: Invert horizontally. insert in the shadow.
Invert V: Invert vertically.
Video: Channel 2 input video signal
To invert the image on the back side Flat Color: Single color
In the [Side H Back] group for side H or [Side V Back] When the [Flat Color] button is selected, set the
group for side V, select the direction of inversion. following parameters.
Invert H: Invert horizontally.
No. Parameter Adjustment
Invert V: Invert vertically.
1 Luminance Luminance
2 Saturation Saturation
Setting a Shadow 3 Hue Hue
162
combined, channel 3 is used as the shadow of channel
1, and channel 4 is used as the shadow of channel 2.
To set a shadow on channels 2 and 3:
Set using the [Ch 2 + Ch 3 Shadow] button and [Ch 2
+ Ch 3 Shadow Source] group.
Channel 4 is used as the shadow of channel 2. The
channel 3 shadow is not added.
To set a shadow on channels 1 and 3:
Set using the [Ch 1 Shadow] button and [Ch 1 Shadow
Source] group and the [Ch 3 Shadow] button and [Ch
3 Shadow Source] group.
Channel 3 is used as the shadow of channel 1, and
channel 4 is used as the shadow of channel 2.
Setting a shadow using four channels
To add shadows before combining images:
Set a “Ch1+Ch2, Ch3+Ch4” combine, and set the [Ch
1 Shadow] button and [Ch 3 Shadow] button to the on
state. The images for channel 1 and channel 3 with
added shadow are combined.
To add shadows after combining images:
Set a “Ch1+Ch2+Ch3+Ch4” combine, and set the [Ch
1 + Ch 2 Shadow] button to the on state. Shadows are
added to the combined channel 1 and channel 2 image.
163
External Devices Chapter 13
• To use a disk recorder, the target file from the file list
External Device Control must be loaded.
For details, see “Disk Recorder File Operations”
(page 171).
You can control operations on the following types of
external device. Effect timelines
• P-Bus (Peripheral Bus II protocol) devices You can register external device control data on an effect
• GPI devices timeline.
• VTRs (Sony 9-pin VTR protocol)
• Disk recorders (video disk communications protocol, Effect timeline registers
Odetics protocol) The maximum number of registers that can be used in an
• AMP (Advanced Media Protocol) compatible devices 1) external device region is given below.
1) Unless otherwise specifically stated in this document, “disk recorder” Device 1 to Device 12: 250 per device
includes AMP compatible devices. P-Bus: 250
GPI: 99
You can also operate external devices controlled by other
protocols over a network using general-purpose TCP/IP Notes
connection settings.
For details about the devices that can be connected, consult • Actions configured on an effect timeline are executed
your Sony representative. only when the effect timeline is operating in the normal
direction.
Control of GPI devices • The following actions cannot be set.
Operate an external device using a GPI output port. - Keyframe loop
- Effect timeline loop
Control of P-Bus devices, VTRs, and disk
- Reverse direction execution
recorders
- Normal/reverse direction execution
Operate an external device using a serial port or network
- Keyframe path
port.
Notes
• The maximum number of ports that can be used,
including serial ports and network ports, is 40.
• A serial port can be used when an XKS-G1700 Legacy
Interface Board (option) is installed.
• Control of P-Bus compatible devices, AMP compatible
devices, and TCP/IP connected devices is supported on
network ports.
• Control of AMP compatible devices is not supported on
serial ports.
• The connection ports must be configured in order to
operate devices connected to serial ports or network
ports.
For details, see “Setting the Connection Port of External
Devices” (page 335).
164
Note
Control of VTRs and Disk External devices connected via general-purpose TCP/IP
Recorders connection cannot be operated using the device control
block buttons, Cueup & Play, DDR/VTR timeline, or
similar functions. Control of external devices is supported
by sending commands using macros.
VTR/Disk Recorder Operations
(Device Control Block) Operating a VTR/disk Recorder
The device control block can be switched to device/frame
You can control VTRs, disk recorders, and other external
memory/clip player operation mode for operating a VTR/
devices using serial ports and network ports. Up to 12
disk recorder.
devices can be controlled.
The following operations are supported for an external
device.
1 Press the [DEV] button.
The [DEV] button is lit amber, and the operation mode
Device control block: switches to device/frame memory/clip player
Operation using the operation buttons and channel operation mode.
selection buttons in the device control block.
• Operating device selection 2 Using the channel selection buttons, select the target
• Tape/disk transport control channel (CH1 to CH12) for operation.
• Start point/stop point setting
• Recording to VTR/disk recorder You can select multiple channels. The first selected
• Loop/recue setting button becomes the reference channel, and is lit green.
Cueup & Play: Subsequent selected buttons are lit amber.
Saving the following information in effect timeline
registers, recalling registers, and carrying out 3 Operate the external device.
operations using the buttons or menu in the utility
VTR/disk recorder operations
control block.
Operate using the following device/frame memory/clip
• Start point/stop point
player operation mode buttons.
• Start delay time
• Loop/recue setting Button Operation
DDR/VTR timeline:
LOOP (Enabled only for the video disk
Registering the following actions in keyframe points communications protocol)
on an effect timeline, recalling registers, and issuing Return to the start point when playback
action commands. finishes, and repeat playback in a loop.
• Start/stop RECUE (Enabled only for the video disk
• Cueing up the start point communications protocol)
• Variable speed Return to the start point when playback
finishes and stop.
Channel selection buttons REC Press the [REC] button and [PLAY] button
To operate a VTR/disk recorder, the target device port simultaneously to start recording.
must be assigned to a channel selection button (CH1 to START TC Set current position as the start point.
CH12) of the device control block beforehand.
The devices assigned to the channel selection buttons STOP TC Set current position as the stop point.
(CH1 to CH12) correspond to device 1 to device 12. STB OFF Set standby off.
STOP Stop the tape/disk.
For details, see “Setting Channel Selection Buttons” CUE Move to the start point.
(page 322).
REW Rewind.
Setting the protocol PLAY Play.
The protocol (device type) of the connection port must be FINE (Enabled only for the video disk
set according to the VTR/disk recorder connected to the communications protocol)
port. Enable fine adjustment using the Z-ring while
the [SHTL] button or [JOG] button is pressed
(fine mode).
For details, see “Setting the Connection Port of External
Devices” (page 335). FF Fast forward.
165
Button Operation
Low Still image Low
VAR Set variable-speed playback in variable mode. speed speed
JOG Set variable-speed playback in jog mode.
SHTL Set variable-speed playback in shuttle mode.
ALL STOP Stop all operations. Reverse Forward
direction direction
To change the playback speed
Press the [VAR] button, [SHTL] button, or [JOG] button,
then turn the Z-ring during playback. Turn the Z-ring Maximum Maximum
clockwise to play in the normal direction, or speed speed
counterclockwise to play in the reverse direction. The
playback speed varies according to the angle. To record
To cancel variable-speed playback, press the [STOP] You can record to a VTR or a disk recorder (video disk
button. You can also press the [STB OFF], [CUE], [REW], communications protocol).
[PLAY], [FF], or [ALL STOP] button to cancel. Press and hold the [REC] button and press the [PLAY]
Variable mode: button to start recording.
Press the [VAR] button, turning the button on amber, to set During recording, the [REC] button is lit red.
the Z-ring to variable mode. To stop recording, press the [STOP] button or the [ALL
The playback speed varies according to the rotation angle STOP] button.
of the Z-ring from –1 to +3 times normal speed.
Notes
Low Still image Low
speed speed • Recording is not possible when using the Odetics
protocol or AMP protocol.
• The following limitations apply for a disk recorder
(video disk communications protocol).
Reverse Forward - Set the disk recorder type to [Recorder].
direction direction
- The maximum length of time that can be recorded in
one operation is 30 minutes.
–1× +1× - Create a new file for recording.
+3× - When resuming after interrupting recording, recording
to a file continues from the interruption point. To
Jog mode: record to a file other than the selected file, unload the
Press the [JOG] button, turning the button on amber, to set file and create a new file.
the Z-ring to jog mode.
You can advance the content frame by frame at a speed
proportional to the rotation speed of the Z-ring. To show a
still image, stop turning the Z-ring.
VTR/Disk Recorder Status Display
Open the following menus.
• Home > External Device > Device > Cueup & Play
menu (16101.31)
• Home > External Device > Device > Timeline > Action
Reverse Forward menu (16101.41)
direction direction • Home > External Device > Device > Timeline > Rewind
Action menu (16101.42)
Information for the assigned VTR/disk recorder is
displayed for each channel selection button.
You can check the current timecode in [Current TC].
Shuttle mode:
You can check the current VTR/disk recorder status in
Press the [SHTL] button, turning the button on amber, to
[Status].
set the Z-ring to shuttle mode.
The playback speed varies in steps according to the Status VTR Disk recorder
rotation angle of the Z-ring, up to a maximum of 50 times
XXXX Communication with Cannot communicate
normal. device is normal, but with device, or
status information communicating but
cannot be acquired. cannot read the device
type.
166
Status VTR Disk recorder Notes
Local The REMOTE/LOCAL Port is not open.
switch of the device is
• Loop/recue are only available for disk recorders that use
set to LOCAL. the video disk communications protocol. Note that these
may not operate, depending on the connected device.
Tape Out No tape is loaded. No file loaded. a)
• To use the loop or recue function, it is necessary to
Rec Recording Recording a) enable the function.
Cue> Cueing up in the – For details, see “Setting loop/recue” (page 337).
normal direction
Cue< Cueing up in the –
Notes on cueup & play
reverse direction • Cueup & play cannot be configured for registers in
which a DDR/VTR timeline is configured.
Eject Ejecting cassette –
• When using a disk recorder with cueup & play, if you
Stb Off Stopped in standby off – carry out the following sequence of operations, playback
mode
may freeze on the frame of the start point.
Stop Stopped in standby on Stopped - Press the [RUN] button to play to a point close to the
mode end of a file t stop playback t press the [RUN]
Play Playing Playing button again.
FF Fast forwarding – Perform the following operation if playback freezes.
Rewind Rewinding –
- Recall another register t recall the target register t
press the [REWIND] button t press the [RUN]
Shtl> Playing in the normal – button.
direction in shuttle
mode
Shtl< Playing in the reverse – Setting cueup & play (device control block)
direction in shuttle
mode.
Set the start point, stop point, and loop/recue using the
device control block in device/frame memory/clip player
Var> Playing in the normal Playing in the normal operation mode.
direction in variable direction in variable
mode. mode. Selecting regions and saving/recalling registers are
controlled using the menu.
Var< Playing in the reverse Playing in the reverse
direction in variable direction in variable
mode. mode. For details, see “Setting cueup & play (menu)”
(page 168).
Jog> Playing in the normal Playing in the normal
direction in jog mode. direction in jog mode.
Jog< Playing in the reverse Playing in the reverse Note
direction in jog mode. direction in jog mode.
The start delay time cannot be set using the device control
Still Playing still image – block.
a) Not supported for the Odetics protocol and AMP protocol.
1 Press the [DEV] button.
The [DEV] button is lit amber, and the operation mode
Cueup & Play switches to device/frame memory/clip player
operation mode.
You can save cueup & play settings, such as start point/
stop point timecodes, in an effect timeline register and then 2 Using the channel selection buttons, select the target
recall the settings as required. channel (CH1 to CH12) for operation.
Cueup & play is configured using the device control block
or the menu. Recall a register in which cueup & play You can select multiple channels. The first selected
settings are saved, and then control operation using the button becomes the reference channel, and is lit green.
utility control block or the menu. Subsequent selected buttons are lit amber.
Loop/recue 3 Set the start point.
Loop/recue can be set for disk recorders that use the video
disk communications protocol. Play the target device to set using the device control
Loop: Playback from the start point to the stop point, then block and press the [START TC] button at the position
return to the start point and repeat playback. to set as the start point.
Recue: Playback from the start point to the stop point, then
return to the start point and stop. 4 Set the stop point.
167
Play the target device to set using the device control Loop: Set loop.
block and press the [STOP TC] button at the position Recue: Set recue.
to set as the stop point. To set neither loop or recue, set the [Loop] button and
[Recue] button to the off state.
5 Set loop/recue.
Note
Press the [LOOP] button, turning it on, to set loop. Or
press the [RECUE] button, turning it on, to set recue. Loop/recue are only available for disk recorders that
To set neither loop or recue, set the [LOOP] button and use the video disk communications protocol.
[RECUE] button to the off state.
8 Save the register.
Note
In the [Effect Timeline Recall/Store] taskbar, press the
Loop/recue are only available for disk recorders that [Recall/Store] button to display the [Recall/Store
use the video disk communications protocol. Register] window. Press the [Store] button, check the
register number, and press [Enter]. You can change the
register number if you want to save in a register
Setting cueup & play (menu) different from the recalled register.
1 Select a region and recall a register. For details about saving an effect timeline register, see
“Saving an Effect Timeline” (page 201).
In the [Effect Timeline Recall/Store] taskbar, press the
[Recall/Store] button to display the [Recall/Store
Register] window. Select an external device region Executing cueup & play (utility control
(Device1 to Device12), press the [Recall] button, enter block)
a register number, and press [Enter]. You can execute cueup & play using the utility control
For details about recalling an effect timeline register, block.
see “Recalling an Effect Timeline” (page 200). Selecting regions and recalling registers are controlled
using the menu.
2 Open the Home > External Device > Device > Cueup
& Play menu (16101.31). For details, see “Executing cueup & play (menu)”
(page 168).
Cueup & play settings information is displayed for
each device channel number (1 to 12). You can also select a region and recall an effect timeline
register by recalling a shotbox register in the utility control
3 Select the target device for operation. block.
4 Press the left button in the [Start TC] group and enter For details, see “Executing a Shotbox (Utility Control
a start point timecode in the numeric keypad window. Block)” (page 234) and “Assigning a Utility Function”
(page 318).
To clear the setting
Press the [Clear] button in the [Start TC] group. Operate using the following buttons.
[REWIND] button: Cueup the start point timecode.
5 Press the left button in the [Stop TC] group and enter During cueup, the [ALL STOP] button in the device
a stop point timecode in the numeric keypad window. control block flashes amber and then lights green
To clear the setting when the start point is reached. During cueup on the
Press the [Clear] button in the [Stop TC] group. reference region device when multiple devices are
selected, the [CUE] button flashes amber and then
6 Press the left button in the [Delay] group and enter a lights green when the start point is reached.
start delay time in the numeric keypad window. [RUN] button: Start playback. Playback stops at the stop
point timecode.
Set a value in the range 00:00 to 59:xx (“xx” is the
number of frames per second – 1 frame).
Executing cueup & play (menu)
To clear the setting
Press the [Clear] button in the [Delay] group. 1 Select a region and recall a register.
7 In the [Mode] group, set loop/recue. In the [Effect Timeline Recall/Store] taskbar, press the
[Recall/Store] button to display the [Recall/Store
168
Register] window. Select an external device region
(Device1 to Device12), press the [Recall] button, enter 30 frames 30 frames
a register number, and press [Enter].
For details about recalling an effect timeline register,
see “Recalling an Effect Timeline” (page 200). 15 15
frames frames
169
- Recall another register t recall the target register t Setting an action
press the [REWIND] button t press the [RUN] You can configure an action at a keyframe point on an
button. effect timeline.
• Some operating limitations apply when the video disk
communications protocol is used. For details about setting an effect timeline, see “Setting an
These are explained with reference to the following Effect Timeline” (page 200).
figure, which illustrates creation of a timeline that plays
from the video of file A to the video of file B. For a disk recorder, the target file must be loaded.
170
To clear the setting To clear the setting
Press the [Clear] button in the [Start TC] group. Press the [Clear] button in the [Start TC] group.
5 Press the left button in the [Stop TC] group and enter 5 Press the left button in the [Stop TC] group and enter
a stop point timecode in the numeric keypad window. a stop point timecode in the numeric keypad window.
To clear the setting To clear the setting
Press the [Clear] button in the [Stop TC] group. Press the [Clear] button in the [Stop TC] group.
6 Press the left button in the [Variable Speed] group and 6 Press the left button in the [Variable Speed] group and
enter a variable speed in the numeric keypad window. enter a variable speed in the numeric keypad window.
To calculate variable speed automatically To clear the setting
Press the [Fit] button in the [Variable Speed] group. Press the [Clear] button in the [Variable Speed] group.
The duration calculated from the start point and stop
point is compared with the keyframe duration, and the To set a currently loaded file as the rewind action
variable speed is calculated automatically. target
Press the [File Set] button.
To clear the setting
Press the [Clear] button in the [Variable Speed] group. To test an action command output
Press the [Test Fire] button.
To test an action command output
Press the [Test Fire] button.
Disk Recorder File Operations
Setting an action when rewind is executed
Recorded content on a disk recorder is managed as files.
On a DDR/VTR timeline, normally when the [REWIND]
button is pressed, an action set for the first keyframe is not Loading a File
executed. When the [RUN] button is pressed, then the first To control playback and other operations on a disk
keyframe action is executed. recorder, the target file from the file list in the disk recorder
To execute a specific action when the [REWIND] button must be loaded.
is pressed, set a rewind action.
Note
Note
Folder selection is required for the AMP protocol. The
The rewind action is enabled when you press the files in the selected folder are displayed in the file list.
[REWIND] button, even if you have configured an action
for the first keyframe to be executed after rewinding. For details, see “Selecting a folder” (page 172).
For details, see “Setting the operation of the first keyframe File list sharing
when rewind is executed” (page 328). You can share the file list when a single disk recorder is
connected to multiple ports.
1 Open the Home > External Device > Device >
Timeline > Rewind Action menu (16101.42). For details, see “Configuring file list sharing” (page 322).
Rewind action settings information is displayed for
each device channel number (1 to 12). Note
A file list cannot be shared for the AMP protocol.
2 Select the target device for operation.
171
3 Press the [Refresh] button. Loading a file
The file list is updated. Select the target file to load.
The file list shows the number, file name, file duration,
and the update date and time of the files. Note
A file cannot be loaded if the type of disk recorder is set to
Notes [Recorder].
• The update date and time of the files are not
displayed for the video disk communications 1 Open the Home > External Device > Device > File List
protocol. menu (16101.21).
• The file duration and file update date and time are
not displayed for the Odetics protocol. 2 Display the target device to set.
• If sharing a file list, the file list must be updated on Select a tab to change the device (Device Ch1 to
each target device (Device Ch1 to Device Ch12). Device Ch12) to display.
For details about sharing a file list, see
“Configuring file list sharing” (page 322). 3 Select a file.
To sort the file list display You can also press the [Select File] button and enter a
You can sort the file list in ascending or descending order file number in the numeric keypad window.
by number, file name, or update date and time.
Sort by pressing [v] (ascending) or [V] (descending) for 4 Press the [Load] button.
[No.], [File Name], or [Updated Date/Time].
Note
Selecting a folder
A file cannot be created if the type of disk recorder is set
Select a folder for the AMP protocol. to [Player].
1 Open the Home > External Device > Device > Folder 1 Open the Home > External Device > Device > File List
List menu (16101.11). menu (16101.21).
2 Display the target device to set. 2 Display the target device to set.
Select a tab to change the device (Device Ch1 to Select a tab to change the device (Device Ch1 to
Device Ch12) to display. Device Ch12) to display.
3 Press the [Refresh] button. 3 Press the [New File] button.
The folder list is updated. The [New File] window appears.
The folder list shows the number and folder name.
To sort the folder list display 4 Press the input field and enter a file name using the
You can sort the folder list in ascending or descending keyboard.
order by number or folder name. Enter 8 or up to 23 characters.
Sort by pressing [v] (ascending) or [V] (descending)
for [No.] or [Folder Name]. For details about the number of file name characters,
see “Setting a Disk Recorder (VDCP)” (page 336).
4 Select a folder.
5 Press [OK].
You can also press the [Select Folder] button and enter
a folder number in the numeric keypad window. To unload the selected recording file
Press the [Unload] button.
5 Press the [Set] button.
The selected folder is set as the target.
172
P-Bus timeline settings information is displayed for
Control of P-Bus Devices each device (0 to 23).
173
For details, see “Setting the operation of the first keyframe [Effect Timeline Edit] taskbar
when rewind is executed” (page 328). [Next KF] button: Trigger 7
[Previous KF] button: Trigger 8
1 Open the Home > External Device > P-Bus > Timeline
> Rewind Action menu (16102.12). [Recall/Store Register] window 1)
[Recall] button: Recall
Rewind action settings information is displayed for [Store] button: Learn
each device (0 to 23). 1) Only when displayed using the [Recall/Store] button on the [Effect
Timeline Recall/Store] taskbar or [Effect Timeline Edit] taskbar
2 Select the target device for operation.
To select and set multiple devices, place a check mark Outputting an action command
beside the target devices to set. This section describes output of the Recall command as an
To select and set all devices, place a check mark in the example.
Select All checkbox.
1 Press the [Recall/Store] button on the [Effect Timeline
3 In the [Action] group, select an action to set. Recall/Store] taskbar or [Effect Timeline Edit]
taskbar.
Off: Do not set an action.
Store: Set a store action. The [Recall/Store Register] window appears.
Recall: Set a recall action.
Trigger: Set a trigger action. 2 Select a P-Bus region.
4 Press the [Action No.] button and enter a register On the [External Device] tab, set the [P-Bus] button to
number or trigger number in the numeric keypad the on state.
window.
3 Press the [Recall] button.
When a store action or recall action is selected, set a
register number (1 to 4095). 4 Enter a register number (1 to 250) in the numeric
When a trigger action is selected, set a trigger number keypad area.
(0 to 15).
To test an action command output
5 Press [Enter].
Press the [Test Fire] button. The Recall command is output.
P-Bus Trigger
In a P-Bus trigger, you can output an action command to a
P-Bus device using the control panel and menu buttons.
Note
This can be configured only when a P-Bus trigger is the P-
Bus control mode.
For details about setting the mode, see “Setting the P-Bus
Control Mode” (page 322).
The following gives the buttons that can be used and action
commands that are output.
Utility control block
[RUN] button: Trigger 1
[REWIND] button: Trigger 4
[Effect Timeline Recall/Store] taskbar
[Run] button: Trigger 1
[Rewind] button: Trigger 4
174
Setting an action when rewind is executed
Control of GPI Devices On a GPI timeline, normally when the [REWIND] button
is pressed, an action set for the first keyframe is not
executed. When the [RUN] button is pressed, then the first
You can control a GPI external device via a GPI output keyframe action is executed.
port. To execute a specific action when the [REWIND] button
Operate an external device using a GPI timeline. is pressed, set a rewind action.
Note
GPI Timeline The rewind action is enabled when you press the
[REWIND] button, even if you have configured an action
A GPI timeline is an effect timeline for a GPI device.
for the first keyframe to be executed after rewinding.
You can configure a GPI output port as an action at a
keyframe point on an effect timeline to operate a GPI
For details, see “Setting the operation of the first keyframe
device.
when rewind is executed” (page 328).
Up to eight GPI output ports that output a trigger pulse can
be configured for a single keyframe point.
Executing a GPI timeline outputs a trigger pulse to an
1 Open the Home > External Device > GPI > Timeline
> Rewind Action menu (16103.12).
external device from a GPI output port at the keyframe
point for which an action is configured. Rewind action settings information is displayed for
each GPI timeline port (1 to 8).
Setting an action
2 Select the target GPI timeline port for operation.
You can configure an action at a keyframe point on an
effect timeline. 3 Set the [GPI Action] switch to the on state.
For details about setting an effect timeline, see “Setting an To disable an action, set the [GPI Action] switch to the
Effect Timeline” (page 200). off state.
1 Open the Home > External Device > GPI > Timeline 4 Press the [GPI Port] button and enter a GPI output port
> Action menu (16103.11). number in the numeric keypad window.
GPI timeline settings information is displayed for each
Note
GPI timeline port (1 to 8).
Set the trigger type for a GPI output port set as a GPI
2 Select the target GPI timeline port (1 to 8) for timeline port to [Rising Edge], [Falling Edge], or [Any
operation. Edge].
For details, see “Setting a GPI Output” (page 334).
3 Set the [GPI Action] switch to the on state.
To disable all action settings
To disable an action, set the [GPI Action] switch to the
Press the [All Off] button.
off state.
To test a trigger output
4 Press the [GPI Port] button and enter a GPI output port Press the [Test Fire] button.
number in the numeric keypad window.
Note
Set the trigger type for a GPI output port set as a GPI
timeline port to [Rising Edge], [Falling Edge], or [Any
Edge].
For details, see “Setting a GPI Output” (page 334).
To disable all action settings
Press the [All Off] button.
To test a trigger output
Press the [Test Fire] button.
175
3 Press the [Select Source] button.
Control of Routers A source selection window appears.
Notes
• Delegation button numbers 65 to 128 are not displayed.
• The destination assignment and inhibit settings are
configured in the Home > Setup > Panel > Router >
Delegation Button Assign menu (19104.51).
For details, see “Assigning a Destination” (page 323).
Selecting a Level
You can select the level used by the router.
1 Open the Home > External Device > Router > Router
Xpt menu (16104.11).
Note
Input switching is supported only for the destinations on
delegation button numbers 1 to 64.
1 Open the Home > External Device > Router > Router
Xpt menu (16104.11).
176
Other Functions Chapter 14
Memory recall buttons in the utility control block
Utility Functions (when a menu shortcut is assigned)
On: Lit light purple
Off: Lit purple
The utility functions assign a specific function (action) to Cross-point buttons in the cross-point control
a button for recall when the button is pressed. block
You can assign the following actions to the memory recall On: Lit amber
buttons in the utility control block and the cross-point Off: Not lit
buttons in the cross-point control block.
• Utility command
• Recalling a macro register
• Recalling a shotbox register
• Menu shortcut
Note
To use the menu shortcut function, the control panel must
be linked with the menu.
177
List of Utility Commands
The following utility commands can be assigned.
Command Function
a)
M/E-x PGM1 ST Enable/disable M/E-x program output safe title
a)
M/E-x PGM2 ST x = 1 to 5
M/E-x PGM3 ST a)
a)
M/E-x PGM4 ST
M/E-x PVW ST a) Enable/disable M/E-x preview output safe title
x = 1 to 5
M/E-x CLEAN ST a) Enable/disable M/E-x clean output safe title
x = 1 to 5
M/E-x K-PVW1 ST a) Enable/disable M/E-x key preview output safe title
M/E-x K-PVW2 ST a) x = 1 to 5
P/P PGM1 ST a) Enable/disable P/P program output safe title
P/P PGM2 ST a)
P/P PGM3 ST a)
P/P PGM4 ST a)
P/P PVW ST a) Enable/disable P/P preview output safe title
a)
P/P CLEAN ST Enable/disable P/P clean output safe title
P/P K-PVW1 ST a) Enable/disable P/P key preview output safe title
P/P K-PVW2 ST a)
Color Bkgd2 ST a) Enable/disable color background 2 output safe title
DME Monitor Video ST a) Enable/disable DME monitor video output safe title
DME Monitor Key ST a) Enable/disable DME monitor key output safe title
Frame Memory1 to 16 Enable/disable frame memory output (1 to 16) safe title
ST a)
Clip Player1 to 4 ST a) Enable/disable clip player output (1 to 4) safe title
a)
Multi Viewer1 ST Enable/disable multi viewer output (1, 2) safe title
a)
Multi Viewer2 ST
Edit Preview ST a) Enable/disable edit preview output safe title
a)
Preset ST Enable/disable preset output safe title
a)
Aux 1 to 48 ST Enable/disable AUX output (1 to 48) safe title
GPI 1 to 50 Test Fire Output test trigger from GPI output port
Macro Attachment Enbl Enable/disable macro attachment
Macro AT with Rate Register the transition rate when registering an auto transition macro event
Macro AT with A/B Bus Register the background A bus/B bus cross-points when registering an auto transition macro event
Macro TL with Region Register the target region when registering an effect timeline macro event
Pre Macro Set macro attachment in pre-macro mode
Post Macro Set macro attachment in post-macro mode
Macro Take Resume macro execution
(Enabled in step execution mode or during a pause event with a pause time of “0”)
Macro All Take Resume all paused macros in multi mode
(Enabled in multi mode during a pause event with a pause time of “0”)
Macro Auto Ins Enable/disable macro auto insert mode
Macro Cancel Stop macro execution
Macro All Cancel Stop all simultaneous executing macros in multi mode
DME Override Enable/disable DME override
DME Graphic Enable/disable DME graphics display
(Applied to graphics for channel selected in device control block)
FTB Enable/disable fade-to-black
178
Command Function
AUTO PVW Auto preview
Preset PVW Preset preview
M/E-x Preview M/E-x preview
x = 1 to 5
P/P Preview P/P preview
M/E-x Sub Preview M/E-x preview on the sub side in multi program 2 mode
x = 1 to 5
P/P Sub Preview P/P preview on the sub side in multi program 2 mode
M/E-x K-PVW1 M/E-x key preview 1/key preview 2
M/E-x K-PVW2 x = 1 to 5
P/P K-PVW1 P/P key preview 1/key preview 2
P/P K-PVW2
a) Applies only to output signals assigned in the Home > Setup > System >
Output > Output Assign menu (19101.41).
Selecting a bank
A group comprising the 15 buttons of the memory recall
section are called a “bank.”
179
Executing a utility function The utility functions for the selected bank are assigned
to the 1st row or 2nd row in key bus mode, and to the
1 Press the [UTIL/SBOX] button. 1st row to 4th row in free assign mode.
Note
Action assignments are common to all switcher banks.
Selecting a bank
A group comprising the buttons (24 or 16) in a cross-point
button row are called a “bank.”
There are 10 banks (1 to 10), and you select the target
button for operation by assigning a bank to the cross-point
button row.
You can assign a utility/shotbox bank using the following
delegation buttons.
Notes
• You can assign the delegation buttons to use in key bus
mode and free assign mode to the function button
section.
For details, see “Assigning Control Panel Buttons”
(page 317).
• In key/AUX bus delegation mode, you can assign
delegation buttons to the 1st row.
For details, see “Setting the key/AUX bus delegation
mode button row” (page 320).
180
Program output on the sub side
Multi Program 2
Background B
Background A
Overview
This function divides the hardware of a single switcher
bank into two (main and sub), allowing you to create
images separately on each.
Note
Multi program 2 mode and M/E split cannot be set at the
same time. Enabling M/E split will disable multi program Key (key 1 to key 8)
2 mode and switch to standard mode.
Background B
Background A
Example:
Dedicated M/E-1 main and dedicated M/E-1 sub on two
M/E banks
181
Setting control panel buttons when sharing main
Use for M/E-1 main operations and sub
You can assign the main/sub switching buttons ([MAIN]
button and [SUB] button) to the cross-point control block
and transition control block.
Select a cross-point assign table (see page 303). For details about settings, see “Changing main/sub
You can select separate cross-point assign tables for main configuration data in multi program 2 mode” (page 213)
and sub. and “Changing main/sub configuration data in multi
r program 2 mode” (page 223).
Inhibit key operation (see page 315).
You can inhibit key 1 to key 8 separately on main and sub. To change program output key assignments
When a snapshot or effect timeline is recalled on main or
r
sub, only the keys being used on main and sub, according
Assign control panel buttons (see page 317). to the operation mode configuration data of the switcher
You can set separate assignable buttons for main and sub bank, become the recall target.
when using dedicated main and dedicated sub. When [Recall M/E Config] is enabled in the Home > Setup
Assign the buttons for switching between main and sub
when sharing main and sub. > Switcher > Config > M/E Config menu (19103.12), you
can also change the key assignment in the Common > Key
Setting control panel buttons when using Priority/Key Assign menu of the switcher bank.
dedicated main and dedicated sub This section describes the M/E-1 menu as an example.
You can assign the assignable buttons in the cross-point
control block, transition control block, and Flexi Pad Note
control block separately on main and sub.
The key assignment is linked to the Home > Setup >
For details about assigning buttons, see “Assigning Switcher > Config > PGM Config menu (19103.13)
Control Panel Buttons” (page 317). settings.
182
1 Open the Home > M/E-1 > Common > Key Priority/ Note
Key Assign menu (11110.11).
The [MAIN] button and [SUB] button must be assigned to
The key assignment status of the program 1 output to the function button section of the cross-point control block
program 4 output are shown at the bottom. beforehand.
2 Select the target program output (PGM1 to PGM4) to For details about assigning buttons, see “Assigning
set. Control Panel Buttons” (page 317).
3 Press the [Edit] button. 1 Press the [MAIN] button, turning it on.
The [Enable Key] window appears. If the [SUB] button is lit, press the [SUB] button,
turning it off.
4 Place a check mark in the keys to enable.
2 Create the main side image.
Notes
• SL keys 5 to 8 are enabled/disabled as a group.
3 Press the [MAIN] button, turning it off.
• SL keys are disabled for PGM2 to PGM4.
4 Press the [SUB] button, turning it on.
5 Press [OK].
5 Create the sub side image.
Settings and functions added in multi 6 Press the [MAIN] button, turning it on.
program 2 mode
Both the [MAIN] button and [SUB] button should be
• Sub switcher bank menus (M/E-1 Sub to M/E-5 Sub, turned on.
P/P Sub) are added.
• The sub switcher banks (M/E-1 Sub to M/E-5 Sub, P/P Note
Sub) are added to the menu as setup targets.
• Sub switcher bank regions (M/E-1 Sub to M/E-5 Sub, When both the [MAIN] button and [SUB] button are
P/P Sub) are added. selected, the control panel shows the status of the main
• Main and sub switcher banks and keys are shown on the side.
transition control block display.
Switcher banks: MAIN (dedicated main), SUB 7 Execute a transition.
(dedicated sub), MAIN&SUB (shared main and sub)
Keys: M (key assigned to main), S (key assigned to sub) Both main side and sub side images are switched.
• When extended re-entry is enabled for switcher banks,
re-entry signals within the main switcher bank, within
the sub switcher bank, and between main and sub Multi Program 2 Mode Restrictions
switcher banks can be selected.
For details about extended re-entry, see “Setting In multi program 2 mode, settings and functions have the
Extended Re-Entry” (page 308). following restrictions.
• “Sub” and “Main&Sub” settings are added to macro • A key wipe has the following restrictions.
event parameters and macro attachment list buttons. - Only standard wipe patterns can be used
For details about macro events, see “Macro Events” - Pattern mix cannot be used
(page 377). - Split, pairing, modulation, spring, and spiral cannot be
For details about macro attachment lists, see “Macro used
Attachment Lists” (page 384). - Edge fill color matte is flat color only
• Sub switcher bank preview is added to the utility - Four types of multi replication are available for
commands. selection
For details about utility commands, see “List of Utility • The key priority cannot be changed, depending on the
Commands” (page 178). transition.
• Transition preview cannot be used.
• DMEs can be used in up to two locations simultaneously
Image creation operation on main and sub.
This section describes the operation of a switcher bank - When using a DME wipe only
shared between main and sub as an example. 1-channel mode DME wipe: Can be used separately on
To switch between main and sub, press the [MAIN] button main and sub.
or [SUB] button in the cross-point control block.
183
2-channel mode or 3-channel mode DME wipe: Can
be used on either main or sub only.
- When using a processed key only
AUX Bus Functions
One DME channel: Can be used on two keys (main
and/or sub)
Two to four DME channels: Can be used on one key Selecting an AUX Bus/Edit Preview
(main or sub).
- When using the image effect function
Bus Signal
Can be used on two backgrounds (background A bus/ You can switch AUX bus and edit preview bus signals
B bus on main and/or sub). using the menu.
• On a sub switcher bank, configuration data cannot be From the list of cross-point button numbers, select the
copied or swapped. button number assigned with a signal.
• On a sub switcher bank, the “AUTO PVW” utility
command cannot be used. 1 Open the Home > Other Effects > Aux Bus > Aux Xpt
• In the following cases, a transition using the fader lever menu (18102.11).
may not be performed correctly.
- When flip-flop mode/bus fixed mode are set 2 Select the target bus for operation.
differently on main and sub
- For 2-stroke operations, such as a pattern limit or 3 Press the [Edit] button.
preset color mix
• When a snapshot/effect timeline is recalled A signal selection window for the selected bus
simultaneously on main and sub, the following data is appears.
reflected in the settings for main.
- Keys 4 Select a video signal or key signal in [Select Source
- Switcher bank operation mode Type].
- DME external video bus and utility 1 bus
• When a snapshot/effect timeline is recalled which has a To select a video signal, set the [Video] radio button to
different operation mode setting than the current the on state.
switcher bank operation mode, the following occurs. To select a key signal, set the [Key] radio button to the
- If the operation mode is not a target of the snapshot, on state.
the current operation mode settings are used for
snapshot reproduction. 5 Switch the signal using the cross-point selection
- If the operation mode is a target of the snapshot, the buttons.
operation mode configuration data saved in the Select a tab to change the button number to display.
snapshot/effect timeline is applied and then the other Setting a cross-point selection button to the on state
data is recalled. switches the cross-point.
• The [MACRO ATTACH ENABLE] button settings are
common to main and sub.
• On DME utility 1 bus and DME utility 2 bus cross-point
buttons, it is not possible to set separate macro AUX Mix
attachments on main and sub.
• Link settings are maintained even when the switcher In addition to a switcher bank transition, you can also
bank operation mode is changed. Change the link perform a transition between two AUX buses.
settings, as required.
• Since key 1 to key 8 are shared between main and sub, if Assigning AUX buses to outputs for an
the main and sub fader lever positions are different and AUX mix
you move the fader lever, the image changes
instantaneously to the state of the most recently moved Assign two AUX buses used for an AUX mix to
fader lever. consecutive odd-numbered and even-numbered outputs.
• When a preset color mix is selected on main or sub, it is Select an output in the Home > Setup > System > Output
not possible to perform an independent key transition > Output Assign menu (19101.41) and assign two
operation on main and sub. consecutive AUX buses as a group (Aux1/2 to Aux47/48).
184
Executing an AUX mix (cross-point control To set the transition rate
block) Press the button on the right of the [On] radio button
and enter a transition rate in the numeric keypad
This section describes an AUX mix using the AUX1 bus window.
and AUX2 bus as an example.
This switches from the image currently output on the To switch the video signal and key signal
AUX1 bus to a new image using an AUX mix. To select a video signal, set the [Video] radio button
for [Select Source Type] to the on state.
Notes To select a key signal, set the [Key] radio button for
[Select Source Type] to the on state.
• The button used to execute an AUX mix must be
assigned to the function button section of the cross-point 5 Execute an AUX mix using the cross-point selection
control block beforehand. buttons.
For details about assigning buttons, see “Assigning
Control Panel Buttons” (page 317). Select a tab to change the button to display.
• The AUX mix transition rate is configured using the Set the cross-point selection button assigned with the
menu. image for after the transition to the on state to execute
For details about settings, see “Executing an AUX mix the AUX mix.
(menu)” (page 185). The image during the transition is output on the AUX1
bus. The selected image is output on the AUX2 bus.
1 Press the [AUX MIX] button, turning it on.
Note
Use the [AUX MIX] button for the cross-point button
row assigned with the AUX1 bus. When the output signal conversion format is 2160P
2SI 3G, the image during the transition is also output
2 Select an image for after the transition in the cross- on the even-numbered AUX bus.
point button row assigned with the AUX1 bus.
The image during the transition is output on the AUX1
bus. AUX Bus Color Corrector
The selected image is output on the AUX2 bus.
You can set the following color corrector functions for
AUX bus outputs.
Note
• Video process
When the output signal conversion format is 2160P • Primary color correction
2SI 3G, the image during the transition is also output • RGB clip
on the even-numbered AUX bus. To use a color corrector, an AUX bus must be assigned to
an output that can be configured with a color corrector/
HDR converter.
Executing an AUX mix (menu)
This section describes an AUX mix using the AUX1 bus For details about outputs that can be configured with a
and AUX2 bus as an example. color corrector/HDR converter, see “Selecting Outputs
This switches from the image currently output on the Configurable with a Color Corrector/HDR Converter”
AUX1 bus to a new image using an AUX mix. (page 296).
1 Open the Home > Other Effects > Aux Bus > Aux Xpt
Notes
menu (18102.11).
• When AUX mix is enabled, the color corrector is set for
2 Select the AUX1 bus. odd-numbered AUX buses.
• When the system signal format is 1080P or 1080i, a color
3 Press the [Edit] button. corrector cannot be used.
The AUX1 bus signal selection window appears.
Setting a color corrector
4 In [Aux Mix], set the [On] radio button to the on state.
1 Open the Home > Other Effects > Aux Bus > Aux Bus
To disable an AUX mix, set the [Off] radio button to CCR menu (18102.21).
the on state.
The color corrector settings information is displayed
for each AUX bus.
185
The color space (BT.709 or BT.2020) is displayed for
each AUX bus assigned to an output that can be Output level
configured with a color corrector/HDR converter. White balance
adjustment
2 Select the target AUX bus to set.
1 Open the Home > Other Effects > Aux Bus > Aux Bus Input level
CCR menu (18102.21). Knee correction
No. Parameter Adjustment 1 Open the Home > Other Effects > Aux Bus > Aux Bus
1 Video Gain Video signal gain CCR menu (18102.21).
2 Y Gain Luminance signal gain
2 Select the target AUX bus to set.
3 C Gain Chrominance signal gain
4 Hue Delay Hue delay 3 Set the [Primary CCR] button in the [Primary CCR]
5 Black Level Black level group to the on state.
To return the video process function settings to 4 In the [Primary CCR Adjust] group, select an
the defaults adjustment item.
Press the [Unity] button in the [Video Process] group,
check the message, then press [OK]. Black: Black balance adjustment
White: White balance adjustment
Gamma: Gamma correction
Setting primary color correction Knee: Knee correction
The following types of correction can be applied to each of
the RGB signals. 5 Set the following parameters.
• Black balance adjustment: Sets the output level for a 0%
level input signal.
• White balance adjustment: Sets the output level for a
100% level input signal.
• Gamma correction: Adjusts the curvature of the gamma
curve.
• Knee correction: Adjusts the position of the knee of the
gamma curve.
186
No. Parameter Adjustment Note
1 Red R signal adjustment The enable/disable setting is applied to all link groups.
2 Green G signal adjustment
3 Blue B signal adjustment
1 Open the Home > Other Effects > Aux Bus > Aux Bus
CCR menu (18102.21).
4 All Simultaneous adjustment of all
RGB signals a) 2 Set the [Link Enable] button in the [Aux Bus CCR
a) [Red] parameter value is shown. Link] group to the on state.
To return primary color correction settings to the To disable a link group, set the [Link Enable] button to
defaults the off state.
Press the [Unity] button in the [Primary CCR] group,
check the message, then press [OK]. To apply the same settings to color correctors in
a group
If the settings of AUX bus color correctors within a group
Setting RGB clip are different, you can set the same settings by copying the
settings of a specific AUX bus.
1 Open the Home > Other Effects > Aux Bus > Aux Bus Select an AUX bus and press the [Copy in Link Group]
CCR menu (18102.21). button in the [Aux Bus CCR Link] group.
The color corrector of all AUX buses in the group are set
2 Select the target AUX bus to set. to the same settings as the selected AUX bus.
187
No. Parameter Adjustment
Color Backgrounds 1 Size Pattern size
2 Soft Softness of the pattern contour
5 Pattern Pattern number a)
Overview
a) Linked to the pattern number selected using the [Mix Pattern Select]
A color background is a function used to create a color button.
background image using a color signal generated by a
dedicated generator. 3 Press the [Mix Pattern Select] button.
When the system signal format is 2160P, one color A pattern selection window appears.
background (color background 1) can be used. When the
system signal format is 1080P or 1080i, two color 4 Set the button for the target pattern to the on state.
backgrounds (color background 1 and color background 2)
can be used.
Note
Assign color background 1 and color background 2 to
cross-point buttons, and select color background signals. Dedicated patterns 1 to 24 are the same as standard
wipe patterns 1 to 24.
Types of color backgrounds
You can set a single color (color 1 only) or a color mix 5 Press [OK].
(mix of color 1 and color 2) color background.
In a color mix, color 1 and color 2 are mixed using a 6 Press the [Color 1] button and set color 1 using the
dedicated pattern. You can also add modifiers to the following parameters.
pattern.
188
To replicate a pattern (Multi) To make a wipe pattern like a window blind
You can replicate a pattern horizontally, vertically, or both (Pairing)
up to 63 times. Set the [Pairing] button to the on state and set the following
parameter.
For details about pattern layouts, see “Replicating a wipe
pattern (Multi)” (page 109). No. Parameter Adjustment
1 Width Width
Set the [Multi] button to the on state and set the following
parameters. To add modulation to a pattern (Modulation)
In the [Modulation] group, select a modulation type.
No. Parameter Adjustment H: Modulate a pattern in the horizontal direction.
1 H Multi Number of repetitions of pattern V: Modulate a pattern in the vertical direction.
horizontally The modulation is set to a sine wave.
2 V Multi Number of repetitions of pattern
Set the following parameters.
vertically
No. Parameter Adjustment
3 Invert Type Pattern layout (1 to 4)
1 Amplitude Amplitude of modulation
To set the aspect ratio of a pattern (Aspect) 2 Frequency Frequency of modulation
Set the [Aspect] button to the on state and set the following 3 Speed Speed of ripples
parameter. • Negative values create waves in
the down, left, and
No. Parameter Adjustment counterclockwise directions.
1 Aspect Aspect ratio • Positive values create waves in
• Negative values expand the up, right, and clockwise
vertically. directions.
• Positive values expand
horizontally.
189
• When M/E split is enabled, one DME channel can be
Image Effect used on each of the two sub blocks.
190
Note
For details about the video process function for a key fill
bus, see “Video Process” (page 88).
1 Open the Home > M/E-1 > Bus/Transition > Bus >
Video Process menu (11109.11).
2 Set the [Video Process] button for the target bus to the
on state.
For background A bus
Set the [Video Process] button in the [Background A]
group to the on state.
For background B bus
Set the [Video Process] button in the [Background B]
group to the on state.
191
For utility 1 bus
Set the [Video Process] button in the [Utility 1] group
to the on state.
Safe Title
For utility 2 bus
Set the [Video Process] button in the [Utility 2] group You can enable/disable the safe title function. When
to the on state. enabled, the safe title area is displayed.
You can set the safe title area display method (Box1, Box2,
3 Set the following parameters. Cross, Grid) in the Home > Setup > System > Output >
Safe Title menu (19101.43).
No. Parameter Adjustment For details about settings, see “Setting the Safe Title
1 Video Gain Video signal gain Area” (page 297).
2 Y Gain Luminance signal gain
3 C Gain Chrominance signal gain Note
4 Hue Delay Hue delay You can enable/disable the safe title function using a
5 Black Level Black level utility command.
To return the video process function settings to For details about utility commands, see “Utility
the defaults Functions” (page 177).
Press the [Unity] button for the target bus to set.
1 Open the Home > Utility > Safe Title menu
(18201.11).
192
- Key snapshots
Copy and Swap - Key memory
• When using DME channels on a key to be copied/
swapped, the DME channel selection status may not be
able to be copied/swapped depending on the number of
Overview DME channels that can be used.
• When settings for a normal key are copied to an SL key,
You can copy the settings of a switcher bank or key to the settings for functions that cannot be used on SL keys
another switcher bank or key. are reset to the default values.
You can also swap the settings between switcher banks or
keys. Wipes/DME wipes
The following settings can be copied/swapped. Copy/swap wipe and DME wipe settings using the Home
• Switcher banks > Utility > Copy/Swap > Wipe/DME Wipe menu
Copy/swap settings between switcher banks (18201.33).
• Keys Select a tab to change the target wipe for operation.
Copy/swap settings between keys [Wipe] tab: Wipes
• Wipes [Key Wipe] tab: Independent key transition wipes
Copy/swap wipe settings between switcher banks [DME Wipe] tab: DME wipes
• DME wipes [Key DME Wipe] tab: Independent key transition DME
Copy/swap DME wipe settings between switcher banks wipes
• Independent key transition wipes DMEs
Copy/swap independent key transition wipe settings Copy/swap DME settings using the Home > Utility >
between keys Copy/Swap > DME menu (18201.34).
• Independent key transition DME wipes
Copy/swap independent key transition DME wipe
settings between keys
• DMEs Executing a Copy/Swap
Copy/swap DME settings between DME channels
This section describes copying a wipe as an example.
Copy/swap menus 1 Open the Home > Utility > Copy/Swap > Wipe/DME
Wipe menu (18201.33).
Switcher banks
Copy/swap switcher bank settings using the Home > 2 Select the [Wipe] tab.
Utility > Copy/Swap > M/E menu (18201.31).
3 In the list on the left, select a copy source wipe.
Notes
• The following settings cannot be copied/swapped.
4 In the list on the right, select a copy destination wipe.
- Setup data
- Wipe snapshots
5 Press the [Copy] button.
- DME wipe snapshots To swap
- Snapshots Select the wipes to swap in the lists on the left and right,
- Effect timelines and press the [Swap] button.
- Key snapshots
- Key memory To undo a copy or swap
• When using DME channels on a switcher bank to be To undo a copy or swap immediately after copying/
copied, the DME channel selection status may not be swapping, press the [Undo] button.
able to be copied depending on the number of DME
channels that can be used. Executing a copy using buttons
Keys You can perform the following copy functions using
Copy/swap key settings using the Home > Utility > Copy/ button operations on the control panel.
Swap > Key menu (18201.32).
Copy target Using buttons
Notes Switcher banks [SNAPSHOT] button in the Flexi Pad
control block
• The following settings cannot be copied/swapped.
- Setup data
193
Copy target Using buttons
Keys [KEY1] button to [KEY8] button in key DME Override
operation mode on the Flexi Pad control
block
Wipes [WIPE] button in the Flexi Pad control When DME override is enabled and an effect timeline or
block snapshot is recalled, the DME channel that was used when
DME wipes [DME WIPE] button in the Flexi Pad saving can be forcibly selected.
control block
To copy using control panel buttons, press and hold the Note
copy source button and press the copy destination button. If effects that use the same DME channel are recalled
Example: simultaneously in two or more regions, the DME channel
Copying a wipe is selected in the following order of priority.
Press and hold the [WIPE] button in the Flexi Pad control P/P > P/P Sub > M/E-1 > M/E-1 Sub > M/E-2 > M/E-2 Sub
block of the copy source switcher bank, and press the > M/E-3 > M/E-3 Sub > M/E-4 > M/E-4 Sub > M/E-5 >
[WIPE] button in the Flexi Pad control block of the copy M/E-5 Sub
destination switcher bank.
1 Open the Home > Utility > DME Override menu
(18201.41).
194
DME Channel Status
Display
Open the Home > Utility > Status > DME menu
(18201.41).
You can check the DME channel status.
An “On Air” icon is displayed for DME channels which
are on-air.
Channel: DME channels
Bank: Switcher bank using the DME channels
Key/Bus: Key or bus using the DME channels
Key 1 to Key 8: Key 1 to key 8
Bkgd A: Background A bus
Bkgd B: Background B bus
“- - -” is displayed when using a DME wipe in a
normal transition.
Type: Function using the DME channels
Processed Key: Processed key
DME Wipe: DME wipe
Image Effect: Image effect function
195
Effect Timelines Chapter 15
By default, the first keyframe is executed when an effect
Overview timeline is recalled. You can also configure a setting such
that the first keyframe is not executed.
196
Edit point Variable duration Constant
Attributes mode duration mode
You can add specific attributes for running an effect Edit target when Keyframe Editing a keyframe
an edit point is preceding the edit is not possible.
timeline when it is recalled.
between point becomes the
The attributes are set for an effect timeline register. keyframes edit target.
197
Executing an Effect Timeline
Effect Timeline List
You can execute an effect timeline using the [RUN] button
in the utility control block or the [Run] button in the menu.
You can set a loop for repeated execution.
You can specify the following execution directions of an
Displaying the Effect Timeline List
effect timeline.
Open the Home > Register > Effect Timeline > Timeline
Normal: Executes from the first keyframe to the last
View > List menu (18301.11).
keyframe.
You can check the information in the effect timeline for
Reverse: Executes from the last keyframe to the first
each region in the timeline list.
keyframe.
A blue frame is displayed for the reference region.
Normal/Reverse: Execution direction changes each time
the effect timeline execution finishes.
a b c d
Note
e f g hi j k l
Looping cannot be set for an effect timeline of an external
device region. Only normal execution direction is
supported.
m n o p
c Zoom in button
Enlarges the display of the effect timeline list.
e Region name
g Execution direction
Displays the effect timeline execution direction (normal
direction or reverse direction) using an arrow icon.
i Keyframe loop
Displays the number of loops remaining/number of loops
specified and a loop icon a when keyframe loop is set.
The loop range is indicted by a blue bar.
198
j Pause “Enabled” is displayed for [Display] in the list on the
Displayed when a pause is set. left for regions set for display.
k Stop point timecode 2 In the list on the left, select the target region to set.
199
[DME] tab: DME regions
Setting an Effect Timeline [External Device] tab: External device regions
The first selected region becomes the reference region.
To select all regions configured beforehand
Set the [All Regions] button to the on state.
Recalling an Effect Timeline
For details about setting the regions selected
simultaneously, see “Setting Regions Selected
Notes
Simultaneously” (page 316).
• The first keyframe is executed when an effect timeline is
recalled. You can also configure a setting such that the To select DME local or DME global for the target
first keyframe is not executed. region to edit
For details about settings, see “Setting the operation of To select DME local, set the [DME Local] button to
the first keyframe when a register is recalled” the on state.
(page 328). To select DME global, set the [DME Global] button to
• You can configure a setting such that the state at that the on state.
point in time is inserted automatically as the first
keyframe when an empty effect timeline register is Notes
recalled. • The region selection is common for effect timelines
For details about settings, see “Inserting the first and snapshots.
keyframe automatically when an empty register is • DME local/DME global selection is enabled only
recalled” (page 327). when editing an effect timeline. When recalling,
• You can configure a setting such that when another saving, or executing an effect timeline, both DME
effect timeline register is recalled while editing an effect local and DME global become the target.
timeline, the edited effect timeline is saved • The DME local/DME global selections are common
automatically (auto save function). for all DME regions.
For details about settings, see “Saving an effect timeline • The DME local/DME global selections are linked to
automatically” (page 327). the [LOCAL] button/[GLB] button in the device
• You can configure a setting such that effect timeline edit control block.
mode ends and operation switches to effect timeline
recall/store mode when a register is recalled in edit 4 Press the [Recall] button.
mode.
For details about settings, see “Exiting edit mode 5 Enter a register number in the numeric keypad area.
automatically when a register is recalled during
editing” (page 327). For details about selecting a register, see “Selecting a
register” (page 201).
1 Display the [Effect Timeline Recall/Store] taskbar.
To add a temporary attribute
The effect timeline switches to recall/store mode. Set [Effect Diss] in the numeric keypad area to the on
state.
2 Press the [Recall/Store] button.
The [Recall/Store Register] window appears.
6 Press [Enter] in the numeric keypad area.
The specified register is recalled.
Note
To undo a register recall
In the [Effect Timeline Edit] taskbar, press the [Recall/ To undo a recall immediately after recalling a register,
Store] button to display the [Recall/Store Register] press the [Undo] button.
window.
To set the duration for an effect dissolve
3 Set the button for the target region to the on state. temporary attribute
You can set the duration for an effect dissolve temporary
You can select multiple regions. attribute for each region.
For details about the display in the region display Select the target region to set, press the [Temp Diss
section, see “Region display section” (page 201). Duration] button, and enter a duration (number of frames)
for the effect dissolve in the numeric keypad area.
Select a tab to change the region to display.
[ME] tab: Switcher bank regions
[User] tab: User regions
200
Selecting a register For details about selecting a register, see “Selecting a
Select a register using the numeric keypad area at the register” (page 201).
bottom right of the [Recall/Store Register] window.
Enter a register number in the numeric keypad area and 6 Press [Enter] in the numeric keypad area.
press [Enter] to apply the setting.
When you enter a register number, the register number and The effect timeline is saved in the specified register.
the following information appears on the numeric keypad To undo saving of an effect timeline
area display. To undo saving immediately after saving an effect
e: The register is empty for the currently selected region. timeline, set the [Store Undo Enable] button to the on state
E: The register is empty for all selectable regions. and press the [Undo] button.
L: The register is locked.
To search for an empty register, press [.] (period).
To search for an empty register common to all selectable
regions, press [.] (period) again. Creating and Editing an Effect
Region display section
Timeline
The region display section at the top right of the [Recall/ You can create and edit an effect timeline by recalling an
Store Register] window shows the region selection status. effect timeline register.
The selected regions are displayed in white characters. The After creating and editing an effect timeline, save it in an
reference region is displayed inverted. effect timeline register.
Note
Saving an Effect Timeline
Multiple simultaneous web menu session connections are
supported, but only one of the following pop-up windows
1 Display the [Effect Timeline Recall/Store] taskbar.
can be displayed at any given time.
The effect timeline switches to recall/store mode. Whenever any pop-up window is displayed, the window
previously opened using another menu session is closed.
2 Press the [Recall/Store] button. • [Recall/Store Register] window:
Displayed using the [Recall/Store] button on the [Effect
The [Recall/Store Register] window appears. Timeline Recall/Store] taskbar, [Effect Timeline Edit]
taskbar, or [Snapshot] taskbar
3 Set the button for the target region to the on state. • [Edit Timeline] window:
Displayed using the [All Edit Options] button on the
You can select multiple regions.
[Effect Timeline Edit] taskbar
For details about the display in the region display • [Edit Macro Event] window:
section, see “Region display section” (page 201). Displayed using the [All Edit Options] button in the
[Edit] group in the Home > Register > Macro > Edit
Select a tab to change the region to display. Macro menu (18307.11)
[ME] tab: Switcher bank regions
[User] tab: User regions Effect timeline creation/edit flow
[DME] tab: DME regions
[External Device] tab: External device regions Select a region (see page 200).
The first selected region becomes the reference region. Select the target region to set.
r
To select all regions configured beforehand
Set the [All Regions] button to the on state. Recall an effect timeline register (see page 200).
When creating, recall an empty register. When editing, recall
For details about setting the regions selected the target register to edit.
simultaneously, see “Setting Regions Selected r
Simultaneously” (page 316).
Select an edit point (see page 202).
Select a position on the effect timeline at which to insert a
4 Press the [Store] button. keyframe, or select a keyframe to modify or delete.
r
5 Enter a register number in the numeric keypad area.
Edit a keyframe (see page 202).
The currently recalled register number is displayed on Insert, modify, or delete a keyframe.
the numeric keypad area display. To select another r
register, enter a register number.
201
Set a time (see page 204). Notes
Set the execution time of the effect timeline.
r
• You can also enter a difference value from the currently
set value.
Set a path (see page 206). For details, see “Entering a difference from a current
Set the interpolation processing used between keyframes. value” (page 44).
r • If multiple keyframes are positioned at the same
Save the effect timeline (see page 201). timecode, the keyframe with the lowest number is
Save the created/edited effect timeline in an effect timeline selected.
register.
To move to a specified keyframe number
Press the [Go to KF] button, enter a keyframe number in
Editing a keyframe the numeric keypad area, and press [Enter].
Note Note
The operations during editing and the duration after editing You can also enter a difference value from the currently set
may vary depending on the effect timeline duration mode. value.
For details, see “Duration and Delay” (page 197). For details, see “Entering a difference from a current
value” (page 44).
1 Display the [Effect Timeline Edit] taskbar.
The effect timeline switches to edit mode. Inserting a keyframe
Modifying a keyframe
Note
You can perform the same operation using the [Previous 1 Select an edit point.
KF] button in the [Effect Timeline Edit] taskbar.
To move to the next keyframe
2 Modify a keyframe.
Press the [Next KF] button. 3 Press the [Modify] button.
202
To modify multiple keyframes using relative
values : Background A
Press the [Relative Modify] button instead of the [Modify] : Background B
button.
Differences in modification between [Modify]
button and [Relative Modify] button Keyframe 1 Keyframe 2 Keyframe 3 Execution
When multiple keyframes are selected and modified, the
following will occur.
When modified using the [Modify] button:
Modification values are applied to multiple keyframes as Modify keyframe 2.
absolute values.
Example:
Select keyframes 1 to 3 and
To change the horizontal position of background B using modify simultaneously.
keyframe 2 when keyframes 1 to 3 are selected:
The horizontal position of background B in keyframes 1
and 3 becomes the same as that in keyframe 2.
Keyframe 1 Keyframe 2 Keyframe 3 Execution
: Background A
: Background B
Deleting a keyframe
Note
You can also select and copy multiple keyframes.
203
For details, see “Selecting multiple keyframes” 2 Set the [KF Loop] button to the on state.
(page 204).
“FROM XXX TO” (“XXX” is the current keyframe
number) is displayed on the numeric keypad area
Selecting multiple keyframes display.
You can select multiple keyframes as the edit target.
This operation is enabled only when modifying, deleting, 3 Enter the number of the last keyframe for the loop
or copying a keyframe. range in the numeric keypad area.
To select all keyframes To change the number of the first keyframe in the loop
Set the [All] button to the on state. range, press [Clear]. Enter the number of the first
keyframe, press [Enter], and then enter the number of
To select multiple keyframes within a specified the last keyframe.
range When the number of the last keyframe is entered,
“COUNT” is displayed on the numeric keypad area
1 Select the first edit point (keyframe) for a specified display.
range.
4 Enter the number of loop repetitions (1 to 99, or 0) in
2 Set the [From To] button to the on state. the numeric keypad area.
“FROM XXX TO” (“XXX” is the current keyframe If “0” is entered, an infinite loop is specified.
number) is displayed on the numeric keypad area
display. 5 Press [Enter].
3 Enter the number of the last keyframe for the specified The loop range and number of repetitions are applied.
range in the numeric keypad area.
Notes
To change the number of the first keyframe in the
specified range, press [Clear]. Enter the number of the • The loop between the specified first keyframe and
first keyframe, press [Enter], and then enter the last keyframe is maintained even if a keyframe is
number of the last keyframe. inserted/deleted within the loop range.
• If the first keyframe or last keyframe of the loop
Note range is deleted, the loop is cleared.
2 Set the [Pause] button to the on state. For details, see “Duration and Delay” (page 197).
A pause is set at the selected keyframe. Select the target region to set and an effect timeline
register, and set the duration mode, duration, and delay.
Setting keyframe loop After configuration, save the effect timeline.
You can specify a range on an effect timeline to execute
For details about recalling an effect timeline register, see
the range repeatedly.
“Recalling an Effect Timeline” (page 200).
A loop can be configured at only one location on an effect
timeline.
For details about saving an effect timeline, see “Saving an
Effect Timeline” (page 201).
1 Select the first edit point (keyframe) for a loop range.
204
Setting the duration mode The effect timeline switches to edit mode.
1 Display the [Effect Timeline Edit] taskbar. 2 Press the [All Edit Options] button.
The effect timeline switches to edit mode. The [Edit Timeline] window appears.
2 Press the [All Edit Options] button. 3 Select an edit point (keyframe).
The [Edit Timeline] window appears. The time from the selected keyframe to the following
keyframe is the target to set.
3 Set the duration mode using the [Constant Duration]
button. 4 Press the [KF Duration] button.
On: Set to constant duration mode. “KF DUR XXX:XX” (“XXX:XX” is the current
Off: Set to variable duration mode. keyframe duration) is displayed on the numeric
keypad area display.
Setting the effect duration 5 Enter a keyframe duration in the numeric keypad area.
1 Display the [Effect Timeline Edit] taskbar. Enter a duration as a timecode (second:frame).
2 Press the [All Edit Options] button. You can also enter a difference value from the
currently set value.
The [Edit Timeline] window appears.
For details, see “Entering a difference from a current
3 Press the [Effect Duration] button. value” (page 44).
4 Enter an effect duration in the numeric keypad area. Setting the delay
Enter a duration as a timecode (minute:second:frame).
1 Display the [Effect Timeline Edit] taskbar.
Note The effect timeline switches to edit mode.
You can also enter a difference value from the
currently set value. 2 Press the [All Edit Options] button.
For details, see “Entering a difference from a current The [Edit Timeline] window appears.
value” (page 44).
3 Press the [Delay] button.
5 Press [Enter].
“DELAY XXX:XX” (“XXX:XX” is the current
The effect duration is applied. delay) is displayed on the numeric keypad area
display.
Setting the keyframe duration 4 Enter a delay in the numeric keypad area.
205
5 Press [Enter]. Note
The delay is applied. The items that can be set vary depending on the user region
assignment.
Setting the Keyframe Path For details, see “Setting a User Region” (page 309).
206
Item Description Item Description
Spin All All [Spin] items Rot All All [Rot] items
Spin Src X Rotation around Y-axis (source Rot X Rotation around Y-axis
space)
Rot Y Rotation around X-axis
Spin Src Y Rotation around X-axis (source
Rot Z Rotation around Z-axis
space)
Spin All All [Spin] items
Spin Src Z Rotation around Z-axis (source
space) Spin Src X Rotation around Y-axis (source
space)
Spin X Rotation around Y-axis
Spin Src Y Rotation around X-axis (source
Spin Y Rotation around X-axis
space)
Spin Z Rotation around Z-axis
Spin Src Z Rotation around Z-axis (source
Asp All All [Asp] items space)
Rate X Aspect ratio in X-axis direction Spin X Rotation around Y-axis
Rate Y Aspect ratio in Y-axis direction Spin Y Rotation around X-axis
Skew All All [Skew] items Spin Z Rotation around Z-axis
Skew X Skew in X-axis direction Pers All All [Pers] items
Skew Y Skew in Y-axis direction Pers X Viewpoint position in X-axis
direction
Aspect Aspect ratio
Pers Y Viewpoint position in Y-axis
Pers All All [Pers] items
direction
Pers X Viewpoint position in X-axis
Pers Z Viewpoint position in Z-axis
direction
direction (distance from
Pers Y Viewpoint position in Y-axis viewpoint position)
direction
Axis Loc All All [Axis] items
Pers Z Viewpoint position in Z-axis
Axis X Rotation axis in X-axis direction
direction (distance from
viewpoint position) Axis Y Rotation axis in Y-axis direction
Axis Loc All All [Axis] items Axis Z Rotation axis in Z-axis direction
Axis X Rotation axis in X-axis direction
Home > Register > Effect Timeline > KF Path >
Axis Y Rotation axis in Y-axis direction DME Effect menu (18301.25)
Axis Z Rotation axis in Z-axis direction Use to set the path of items related to a DME effect.
Home > Register > Effect Timeline > KF Path > Item Description
DME 3D Trans Global menu (18301.24) All All items
Use to set items related to global space for DME three-
Edge All All edge items
dimensional transforms.
Border Border
Item Description Crop/Edge Crop/edge softness
All All items Soft
Loc Size All All [Loc Size] items Wipe Crop Wipe crop
Size Scaling (shrink/magnify) (source Video All All video modifier items
space) Modify
Defocus Defocus
Post Loc X Movement in X-axis direction Color Modify Color modify
Post Loc Y Movement in Y-axis direction Mosaic Mosaic
Post Size Scaling (shrink/magnify) Mask Mask
Loc XYZ All All [Loc XYZ] items Freeze Freeze
Loc X Movement in X-axis direction Non Linear Nonlinear
Loc Y Movement in Y-axis direction In/Out All All input/output items
Loc Z Movement in Z-axis direction Bkgd Backgrounds
Video/Key Video/key
207
Home > Register > Effect Timeline > KF Path > Icon Name Description
DME Global Effect menu (18301.26)
S-Curve Speed is reduced or increased
Use to set the path of items related to a DME global effect. before/after keyframes and the
maximum speed occurs between
Item Description keyframes.
All All items Spline Smooth curved path is drawn
Combine Combiner between keyframes.
Shadow Shadow
Brick Brick
Setting the path type for cross-point hold
Path types (Xpt Hold)
You can set the following types of path. 1 Display the path configuration menu and select the
Path type for cross-point hold (Xpt Hold) target item to set.
Icon Name Description For details about menus and items, see “Target of
path setting” (page 206).
Off When reproducing a keyframe,
switch to a registered cross-point.
2 Press the [Xpt Hold] button and select a path type from
the pull-down list.
Xpt Hold When reproducing a keyframe,
maintain the cross-point For details about path types, see “Path types”
selection. (page 208).
2 Press the [Hue] button and select a path type from the
Short Rotate clockwise or pull-down list.
counterclockwise in the direction
closest to the hue of the next For details about path types, see “Path types”
keyframe. (page 208).
Long Rotate clockwise or
counterclockwise in the direction
furthest away from the hue of the Setting the path type for curves (Curve)
next keyframe.
1 Display the path configuration menu and select the
Path types for curves (Curve) target item to set.
Icon Name Description For details about menus and items, see “Target of
Off No change. path setting” (page 206).
208
No. Parameter Adjustment
2 Bias Bias Executing an Effect
3 Continuity Continuity
Timeline
Note
When the path type for a curve (Curve) is set to [Off], You can execute an effect timeline using the utility control
the cross-point hold (Xpt Hold) and hue (Hue) settings block or the menu.
are disabled. When the path type for a curve (Curve) is You can also recall a shotbox register with a registered
set to [Step], the hue (Hue) setting is disabled. effect timeline region and register in the Flexi Pad control
block to execute an effect timeline.
Note
You can set the operation when the [RUN] button is
pressed again during effect timeline execution.
209
When executing in the reverse direction, this moves to the 2 Select a region and recall an effect timeline register.
stop point timecode.
For details, see “Recalling an Effect Timeline”
(page 200).
Note
If the start point is set lower than 01:00:00:00, pressing the 3 Press the [Rewind] button.
[REWIND] button moves to 01:00:00:00.
When executing in the normal direction, this moves to
the start point timecode.
Setting the execution direction When executing in the reverse direction, this moves to
Set using the following buttons. the stop point timecode.
[NORM] button: Execute in the normal direction (from
the first keyframe to the last keyframe). Note
[NORM/REV] button: Execution direction changes each
If the start point is set lower than 01:00:00:00, pressing
time the effect timeline execution finishes.
the [REWIND] button moves to 01:00:00:00.
[REV] button: Execute in the reverse direction (from the
last keyframe to the first keyframe).
Setting the execution direction
Setting a loop
1 Display the [Effect Timeline Recall/Store] taskbar.
Press the [EFF LOOP] button, turning it on.
When an effect timeline is executed, it repeats executing in The effect timeline switches to recall/store mode.
an infinite loop.
To stop the loop, press the [EFF LOOP] button, turning it 2 Select a region and recall an effect timeline register.
off. You can also stop by pressing the [REWIND] button.
For details, see “Recalling an Effect Timeline”
(page 200).
Moving to the start point/stop point 3 Press the [Run Control] button.
1 Display the [Effect Timeline Recall/Store] taskbar. The [Run Control] window appears.
The effect timeline switches to recall/store mode. 4 Set the [Effect Loop] button to the on state.
210
When an effect timeline is executed, it repeats
executing in an infinite loop.
To stop the loop, press the [Effect Loop] button,
Effect Timeline Register
turning it off. You can also stop by pressing the
[Rewind] button.
Operations
5 Press [OK].
Displaying an Effect Timeline
Register
To select a region
211
The last selected region becomes the reference region. The attributes for the selected register appear on the
right.
To select all regions configured beforehand
Set the [All Regions] button to the on state. 4 Set the [Settings] switch to the on state.
For details about setting the regions selected
simultaneously, see “Setting Regions Selected To disable the effect dissolve attribute, set the
Simultaneously” (page 316). [Settings] switch to the off state.
3 Press [OK]. 5 Press the button on the right side of the [Settings]
switch and enter a duration (number of frames) for the
effect dissolve in the numeric keypad window.
Displaying a single region effect timeline
register
Open the Home > Register > Effect Timeline > Edit Editing an Effect Timeline Register
Register > Browse Single Rgn menu (18301.32).
You can check the following information. You can copy, move, and swap register data. You can also
[Region] group region display: rename, lock, and delete a register.
Displays the selected region name. Copying, moving, and swapping registers between
Register list on the left: different regions is supported between the following
Displays a list of registers for the selected region. regions.
• Register number • Between switcher bank regions (M/E-1 to M/E-5, P/P,
• Register name M/E-1 Sub to M/E-5 Sub, P/P Sub)
• Configured attributes • Between DME regions (DME 1 to DME 4)
• Lock icon • Between external device regions (Device 1 to Device 12)
A lock icon is displayed when a register is locked.
Attribute display on the right: Copying a register
Displays the attributes for the register selected in the
list on the left.
Notes
To select a region
• An empty register cannot be copied.
• A locked register cannot be copied.
1 Press the [Select] button in the [Region] group.
The [Select Region] window appears. 1 Open the Home > Register > Effect Timeline > Edit
Register > Copy/Move/Swap menu (18301.33).
2 Set the button for the target region to the on state.
A list of copy source registers is shown on the left, and
Select a tab to change the region to display. a list of copy destination registers is shown on the
[ME] tab: Switcher bank regions right.
[User] tab: User regions
[DME] tab: DME regions 2 Press the [Select] button in the [Region] group on the
[External Device] tab: External device regions left.
The [Select Region] window appears.
3 Press [OK].
3 Set the button for the copy source region to the on
Setting an attribute state.
You can add the effect dissolve attribute to an effect Select a tab to change the region to display.
timeline. [ME] tab: Switcher bank regions
[User] tab: User regions
1 Open the Home > Register > Effect Timeline > Edit [DME] tab: DME regions
Register > Browse Single Rgn menu (18301.32). [External Device] tab: External device regions
2 Select the target region to set. 4 Press [OK].
For details about selecting a region, see “To select a
region” (page 212). 5 In the list on the left, select a copy source register.
To select and copy multiple registers, place a check
3 In the list on the left, select the target register to set. mark beside the target registers to copy.
212
To select and copy all registers, place a check mark in Swapping registers
the Select All checkbox. Select the registers to swap in the same way as for copying
You can also press the [Select Register(s)] button and a register and press the [Swap] button.
enter a register number in the numeric keypad
window. For details, see “Copying a register” (page 212).
6 Press the [Select] button in the [Region] group on the To swap without renaming the registers
right. Set the [w/o Name] button to the on state.
The [Select Region] window appears.
Changing main/sub configuration data in
7 Set the button for the copy destination region to the on multi program 2 mode
state.
When an effect timeline is recalled on main or sub in multi
Select a tab to change the region to display. program 2 mode, only the keys being used on main and
sub, according to the operation mode configuration data of
8 Press [OK]. the switcher bank, become the recall target.
You can also automatically change the operation mode
9 In the list on the right, select a copy destination configuration data saved in a register when copy/move/
register. swap operations are performed between main and sub
registers.
When multiple registers are selected, select the first You can enable/disable this using the [MP2 Auto Correct]
copy destination register. button when main and sub on a switcher bank are selected
You can also press the [Select Destination] button and as the target regions in the Home > Register > Effect
enter a register number in the numeric keypad Timeline > Edit Register > Copy/Move/Swap menu
window. (18301.33).
The copy destination of the first register selected on On: Change the operation mode configuration data for
the left is the first register selected on the right, and the main and sub.
subsequent registers on the right in the same relative Off: Do not change the operation mode configuration data.
positions as the selected registers on the left become
copy destinations. The first register on the right is
shown in light blue, and the subsequent copy Note
destination registers are shown in blue gray. The setting of the [MP2 Auto Correct] button is common
to snapshots.
10 Press the [Copy] button.
11 Check the message, then press [OK]. Locking a register
To copy without renaming a destination register 1 Open the effect timeline register display menu.
Set the [w/o Name] button to the on state.
To lock a multi region register
Open the Home > Register > Effect Timeline > Edit
Moving a register Register > Browse Multi Rgn menu (18301.31).
Notes
To lock a single region register
Open the Home > Register > Effect Timeline > Edit
• An empty register cannot be moved. Register > Browse Single Rgn menu (18301.32).
• A locked register cannot be moved.
2 Select the target region to set.
Select a move source register and move destination
register in the same way as for copying a register and press For details about selecting multiple regions, see “To
the [Move] button. select a region” (page 211).
For details about selecting a single region, see “To
For details, see “Copying a register” (page 212). select a region” (page 212).
To move without renaming a destination register 3 In the list on the left, select the target register to lock.
Set the [w/o Name] button to the on state.
To select and lock multiple registers, place a check
mark beside the target registers to lock.
213
To select and lock all registers, place a check mark in To rename a multi region register
the Select All checkbox. Open the Home > Register > Effect Timeline > Edit
You can also press the [Select Register(s)] button and Register > Browse Multi Rgn menu (18301.31).
enter a register number in the numeric keypad
window. To rename a single region register
Open the Home > Register > Effect Timeline > Edit
4 Press the [Lock] button. Register > Browse Single Rgn menu (18301.32).
Deleting a register For details about selecting a single region, see “To
select a region” (page 212).
Note
3 In the list on the left, select the target register to
A locked register cannot be deleted. rename.
1 Open the effect timeline register display menu. To select and rename multiple registers, place a check
mark beside the target registers to rename.
To delete a multi region register To select and rename all registers, place a check mark
Open the Home > Register > Effect Timeline > Edit in the Select All checkbox.
Register > Browse Multi Rgn menu (18301.31). You can also press the [Select Register(s)] button and
enter a register number in the numeric keypad
To delete a single region register window.
Open the Home > Register > Effect Timeline > Edit
Register > Browse Single Rgn menu (18301.32). 4 Press the [Rename] button.
2 Select the target region to set. The [Rename] window appears.
For details about selecting multiple regions, see “To 5 Press the input field and enter a name (up to 8
select a region” (page 211). characters) using the keyboard.
For details about selecting a single region, see “To
select a region” (page 212).
Renaming a register
Note
214
Snapshots
Attribute types
Chapter 16
Overview You can add the following attributes.
Cross-point hold: When the snapshot is recalled, the cross-
point selection information remains unchanged.
A snapshot is a function that saves the configured status for Auto transition: An auto transition starts simultaneously
applying an effect to an image in a register which can be after a snapshot is recalled.
used to reproduce the same state. You can save a snapshot Effect dissolve: The image changes smoothly from the
in a register and then recall it as required. state before the snapshot is recalled to the snapshot
state.
Auto play: Plays video content immediately after the
Snapshot registers snapshot is recalled.
You can create a snapshot for the following regions. Cross-point hold (DME): Sets cross-point hold for a DME
Switcher bank regions: region.
M/E-1 to M/E-5, P/P, M/E-1 Sub to M/E-5 Sub, P/P
Sub Notes
User regions:
User 1 to User 8 • Cross-point hold operation mode is applied to key bus
DME regions: cross-point hold attributes.
DME 1 to DME 4 (including Global) For details, see “Setting the Cross-Point Hold
External device regions: Operation Mode” (page 313).
Router • If both effect dissolve and auto transition are configured,
There are 99 snapshot registers for each region. the auto transition takes precedence.
215
Temporary attributes
Apart from attributes set in a snapshot register, you can Snapshot Operations
add temporary attributes when a snapshot is recalled. You
set temporary attributes when recalling a snapshot. (Flexi Pad Control Block)
In the Flexi Pad control block, you can perform operations
Bus Override on snapshots for switcher bank region targets.
This function is used to recall a snapshot while You can save and recall a snapshot using the Flexi Pad
maintaining the cross-point selection of background A bus control block of the target switcher bank.
or B bus.
When you press and hold a background A bus or B bus Memory recall section in snapshot
cross-point button and recall a snapshot, the cross-point operation mode
selection state is maintained for the pressed button only.
This is useful for temporarily holding a cross-point Pressing the [SNAPSHOT] button in the Flexi Pad control
selection when cross-point hold is not set. block switches the memory recall section to snapshot
operation mode.
You select registers (1 to 99) and set attributes using the
buttons in the memory recall section.
To allow operations on the 99 snapshot registers, the Flexi
Pad control block groups the registers. A register group is
called a bank.
There are ten banks (0 to 9) and you display and select the
bank corresponding to the target register.
Ten registers are displayed in each bank. Bank 0 displays
register numbers 1 to 9, bank 1 displays register numbers
10 to 19, and so on.
The currently selected bank number and register number
are displayed on the top right button in the memory recall
section.
Note
A register number is not assigned to the bottom left button
of bank 0. You can assign any register number.
Selecting a bank
You can switch banks using the following buttons.
To select bank 0: Press the [BANK0] button.
To select bank 1: Press the [BANK1] button.
To select bank 2: Press the [BANK2] button.
To select bank 0 to 9: Press the [BANK SEL] button and
enter a bank number (0 to 9) using the numeric keypad
buttons in the memory recall section.
To select the previous bank, press the [PREV BANK]
button in the memory recall section.
To select the next bank, press the [NEXT BANK] button
in the memory recall section.
Selecting a register
The selected bank register is displayed in the memory
recall section. Press the button for the target register to
select it.
The register name or register number is displayed on
buttons for registers with a registered snapshot.
216
The button color varies as follows, according to the To undo a register recall
register state. To undo a recall immediately after recalling a register,
Gray characters: Register not containing a registered press the [UNDO] button.
snapshot
White characters: Register containing a registered
snapshot Saving a Snapshot
Lit orange: Last recalled register
217
Snapshot for a region other than a
Snapshot Operations switcher bank
3 Press the [Bank] button and enter a bank number in the Note
numeric keypad window.
In the [Recall/Store Register] window, it is not
The memory recall section switches to display the possible to add the cross-point hold temporary
selected bank. attribute.
You can use the bus override function and the cross-
4 Press the button for the target register to recall. point button row cross-point hold function.
The register button is lit orange and the snapshot is For details, see “Cross-Point Hold” (page 50).
recalled.
218
6 Press [Enter] in the numeric keypad area. 2 Press the [Store] button in the [Mode] group.
The specified register is recalled. 3 Press the [Bank] button and enter a bank number in the
To undo a register recall numeric keypad window.
To undo a recall immediately after recalling a register, The memory recall section switches to display the
press the [Undo] button. selected bank.
To set the duration for an effect dissolve
temporary attribute 4 Press the button for the target register to save.
You can set the duration for an effect dissolve temporary The register button is lit orange and the snapshot is
attribute for each region. saved.
Select the target region to set, press the [Temp Diss
Duration] button, and enter a duration (number of frames)
Note
for the effect dissolve in the numeric keypad area.
If you press a register button in which a snapshot is
Selecting a register already saved, the register data will be overwritten.
Select a register using the numeric keypad area at the
bottom right of the [Recall/Store Register] window. 5 Set attributes.
Enter a register number in the numeric keypad area and
press [Enter] to apply the setting. Set attributes for a register as required.
When you enter a register number, the register number and
the following information appears on the numeric keypad To add the auto transition attribute
area display. Set the [Auto Transition] button to the on state.
e: The register is empty for the currently selected region. To add the effect dissolve attribute
E: The register is empty for all selectable regions. Set the [Activate] button in the [Effect Dissolve] group
L: The register is locked. to the on state.
To search for an empty register, press [.] (period). Press the [Duration] button in the [Effect Dissolve]
To search for an empty register common to all selectable group and enter a duration (number of frames) for the
regions, press [.] (period) again. effect dissolve in the numeric keypad window.
219
2 Select a bank and press the button for the target For details about selecting a register, see “Selecting a
register to rename. register” (page 219).
The [Rename] window appears. 6 Press [Enter] in the numeric keypad area.
3 Press the input field and enter a name (up to 8 The snapshot is saved in the specified register.
characters) using the keyboard.
Note
Snapshot for a region other than a If you press a register button in which a snapshot is
switcher bank already saved, the register data will be overwritten.
Set the state to save in a snapshot and use the following To cancel a snapshot save operation
procedure to save in a snapshot register. To undo saving immediately after saving a snapshot, set
the [Store Undo Enable] button to the on state and press the
1 Display the [Snapshot] taskbar. [Undo] button.
Snapshot recall/store mode is activated.
220
To select all regions configured beforehand
Snapshot Register Set the [All Regions] button to the on state.
For details about setting the regions selected
Operations simultaneously, see “Setting Regions Selected
Simultaneously” (page 316).
221
3 In the register list on the left, select the target register
to set. Editing a Snapshot Register
The attributes for the selected register appear on the You can copy, move, and swap register data. You can also
right. rename, lock, and delete a register.
Copying, moving, and swapping registers between
4 In the attribute display area on the right, set the different regions is supported between the following
attributes. regions.
• Between switcher bank regions (M/E-1 to M/E-5, P/P,
To add the cross-point hold attribute M/E-1 Sub to M/E-5 Sub, P/P Sub)
• Between DME regions (DME 1 to DME 4)
1 Press the [Edit] button for [Xpt Hold].
The [Edit Xpt Hold] window appears. Copying a register
2 Set the button for the target bus to the on state. Notes
You can select multiple buses. • An empty register cannot be copied.
• A locked register cannot be copied.
For the router region
Select a tab to change the level (Level 1 to Level 8) to
display.
1 Open the Home > Register > Snapshot > Edit Register
> Copy/Move/Swap menu (18302.13).
Destination selection delegation buttons appear.
Select the target button row to set, and set the target A list of copy source registers is shown on the left, and
button in the [Xpt Hold] group to the on state. a list of copy destination registers is shown on the
If the [Xpt Hold Level x All] (“x” is 1 to 8) button is right.
set to the on state, all buttons for the displayed level are
set to the on state. 2 Press the [Select] button in the [Region] group on the
left.
3 Press [OK].
The [Select Region] window appears.
To add the auto transition attribute
Set the [Auto Trans] switch to the on state. 3 Set the button for the copy source region to the on
state.
To add the effect dissolve attribute
Select a tab to change the region to display.
1 Set the [Effect Diss] switch to the on state. [ME] tab: Switcher bank regions
[User] tab: User regions
2 Press the button on the right side of the [Effect Diss] [DME] tab: DME regions
switch and enter a duration (number of frames) for the [External Device] tab: External device regions
effect dissolve in the numeric keypad window.
To add the auto play attribute
4 Press [OK].
Only channels assigned to user regions can be 6 Press the [Select] button in the [Region] group on the
selected. right.
To add the cross-point hold (DME) attribute 7 Set the button for the copy destination region to the on
Set the [Xpt Hold] switch to the on state. state.
222
Select a tab to change the region to display. sub, according to the operation mode configuration data of
the switcher bank, become the recall target.
8 Press [OK]. You can also automatically change the operation mode
configuration data saved in a register when copy/move/
9 In the list on the right, select a copy destination swap operations are performed between main and sub
register. registers.
You can enable/disable this using the [MP2 Auto Config]
When multiple registers are selected, select the first button when main and sub on a switcher bank are selected
copy destination register. as the target regions in the Home > Register > Snapshot >
You can also press the [Select Destination] button and Edit Register > Copy/Move/Swap menu (18302.13).
enter a register number in the numeric keypad On: Change the operation mode configuration data for
window. main and sub.
The copy destination of the first register selected on Off: Do not change the operation mode configuration data.
the left is the first register selected on the right, and the
subsequent registers on the right in the same relative
Note
positions as the selected registers on the left become
copy destinations. The first register on the right is The setting of the [MP2 Auto Correct] button is common
shown in light blue, and the subsequent copy to effect timelines.
destination registers are shown in blue gray.
11 Check the message, then press [OK]. 1 Open the snapshot register display menu.
For details, see “Copying a register” (page 222). 4 Press the [Lock] button.
223
Deleting a register For details about selecting a single region, see “To
select a region” (page 221).
Note
3 In the list on the left, select the target register to
A locked register cannot be deleted. rename.
1 Open the snapshot register display menu. To select and rename multiple registers, place a check
mark beside the target registers to rename.
To delete a multi region register To select and rename all registers, place a check mark
Open the Home > Register > Snapshot > Edit Register in the Select All checkbox.
> Browse Multi Rgn menu (18302.11). You can also press the [Select Register(s)] button and
enter a register number in the numeric keypad
To delete a single region register window.
Open the Home > Register > Snapshot > Edit Register
> Browse Single Rgn menu (18302.12). 4 Press the [Rename] button.
2 Select the target region to set. The [Rename] window appears.
For details about selecting multiple regions, see “To 5 Press the input field and enter a name (up to 8
select a region” (page 221). characters) using the keyboard.
For details about selecting a single region, see “To
select a region” (page 221).
Renaming a register
Note
224
4 Press [OK].
Key Snapshot Register 5 In the list on the left, select a copy source register.
Operations To select and copy multiple registers, place a check
mark beside the target registers to copy.
To select and copy all registers, place a check mark in
Displaying a Key Snapshot Register the Select All checkbox.
You can also press the [Select Register(s)] button and
Open the Home > Register > Key Snapshot > Edit Register enter a register number in the numeric keypad
> Browse menu (18303.11). window.
You can check the following information.
[Key Region] group region display: 6 Press the [Select] button in the [Key Region] group on
Displays the selected switcher bank and key. the right.
Register list:
The [Select Region] window appears.
Displays a list of registers for the selected key.
• Register number
• Register name
7 Set the button for the copy destination key to the on
state.
• Lock icon
A lock icon is displayed when a register is locked.
8 Press [OK].
To select a key
9 In the list on the right, select a copy destination
1 Press the [Select] button in the [Key Region] group. register.
The [Select Key Region] window appears. When multiple registers are selected, select the first
copy destination register.
2 Set the button for the target key to the on state. You can also press the [Select Destination] button and
enter a register number in the numeric keypad
3 Press [OK]. window.
The copy destination of the first register selected on
the left is the first register selected on the right, and the
subsequent registers on the right in the same relative
Editing a Key Snapshot Register positions as the selected registers on the left become
You can copy, move, and swap register data. You can also copy destinations. The first register on the right is
rename, lock, and delete a register. shown in light blue, and the subsequent copy
destination registers are shown in blue gray.
1 Open the Home > Register > Key Snapshot > Edit
Moving a register
Register > Copy/Move/Swap menu (18303.12).
A list of copy source registers is shown on the left, and Notes
a list of copy destination registers is shown on the
right. • An empty register cannot be moved.
• A locked register cannot be moved.
2 Press the [Select] button in the [Key Region] group on
Select a move source register and move destination
the left.
register in the same way as for copying a register and press
The [Select Region] window appears. the [Move] button.
3 Set the button for the copy source key to the on state. For details, see “Copying a register” (page 225).
225
To move without renaming a destination register You can also press the [Select Register(s)] button and
Set the [w/o Name] button to the on state. enter a register number in the numeric keypad
window.
Swapping registers 4 Press the [Delete] button.
Select the registers to swap in the same way as for copying
a register and press the [Swap] button. 5 Check the message, then press [OK].
Deleting a register
Note
1 Open the Home > Register > Key Snapshot > Edit
Register > Browse menu (18303.11).
226
3 Set the button for the copy source switcher bank to the
Wipe Snapshot Register on state.
Displaying a Wipe Snapshot To select and copy multiple registers, place a check
mark beside the target registers to copy.
Register To select and copy all registers, place a check mark in
the Select All checkbox.
Open the Home > Register > Wipe Snapshot > Edit You can also press the [Select Register(s)] button and
Register > Browse menu (18304.11). enter a register number in the numeric keypad
You can check the following information. window.
[Region] group region display:
Displays the selected switcher bank. 6 Press the [Select] button in the [Region] group on the
Register list: right.
Displays a list of registers for the selected switcher
bank. The [Select Region] window appears.
• Register number
• Register name 7 Set the button for the copy destination switcher bank
• Lock icon to the on state.
A lock icon is displayed when a register is locked.
To select a switcher bank
8 Press [OK].
1 Open the Home > Register > Wipe Snapshot > Edit Moving a register
Register > Copy/Move/Swap menu (18304.12).
A list of copy source registers is shown on the left, and Notes
a list of copy destination registers is shown on the • An empty register cannot be moved.
right. • A locked register cannot be moved.
2 Press the [Select] button in the [Region] group on the Select a move source register and move destination
left. register in the same way as for copying a register and press
the [Move] button.
The [Select Region] window appears.
227
For details, see “Copying a register” (page 227). To select and delete multiple registers, place a check
mark beside the target registers to delete.
To move without renaming a destination register To select and delete all registers, place a check mark in
Set the [w/o Name] button to the on state. the Select All checkbox.
You can also press the [Select Register(s)] button and
enter a register number in the numeric keypad
Swapping registers window.
Select the registers to swap in the same way as for copying
a register and press the [Swap] button. 4 Press the [Delete] button.
For details, see “Copying a register” (page 227). 5 Check the message, then press [OK].
Note
Locking a register
A locked register cannot be renamed.
1 Open the Home > Register > Wipe Snapshot > Edit
Register > Browse menu (18304.11). 1 Open the Home > Register > Wipe Snapshot > Edit
Register > Browse menu (18304.11).
2 Select the target switcher bank to set.
2 Select the target switcher bank to set.
For details, see “To select a switcher bank”
(page 227). For details, see “To select a switcher bank”
(page 227).
3 Select the target register to lock.
3 Select the target register to rename.
To select and lock multiple registers, place a check
mark beside the target registers to lock. To select and rename multiple registers, place a check
To select and lock all registers, place a check mark in mark beside the target registers to rename.
the Select All checkbox. To select and rename all registers, place a check mark
You can also press the [Select Register(s)] button and in the Select All checkbox.
enter a register number in the numeric keypad You can also press the [Select Register(s)] button and
window. enter a register number in the numeric keypad
window.
4 Press the [Lock] button.
4 Press the [Rename] button.
To release the lock
Select the target register to unlock and press the [Unlock] The [Rename] window appears.
button.
5 Press the input field and enter a name (up to 8
characters) using the keyboard.
Deleting a register
Note
1 Open the Home > Register > Wipe Snapshot > Edit
Register > Browse menu (18304.11).
228
DME Wipe Snapshot
Register Operations
229
Shotboxes Chapter 17
Overview Shotbox Operations
A shotbox is a function that saves one or more
combinations of a region with an effect timeline, snapshot, Creating and Editing a Shotbox
or key snapshot in a register for recall as required.
You can register a region with either an effect timeline or
There are 99 shotbox registers on each control panel.
a snapshot in a shotbox register. You can also register a
key snapshot.
For details about effect timelines, see “Chapter 15 Effect
Timelines” (page 196).
1 Open the Home > Register > Shotbox > Edit Shotbox
menu (18306.11).
For details about snapshots, see “Chapter 16 Snapshots”
(page 215). A list of shotbox registers is shown on the left. The
register name and number of regions are displayed for
Auto run registers in which a shotbox is saved.
A list of regions and registers registered in the selected
When auto run is enabled, an effect timeline can be shotbox register are shown on the right.
automatically executed when a shotbox register is recalled.
You can set auto run for each shotbox register. 2 In the list on the left, select a shotbox register.
When creating, select an empty register. When editing,
select the target register to edit.
You can also press the [Select Register] button and
enter a register number in the numeric keypad
window.
230
2 Set the button for the target region to the on state. 3 Press [OK].
You can select multiple regions. The selected regions are added to the list on the right.
The selected regions are displayed in white characters
in the region display section at the top. 4 In the list on the right, select the target region to set.
Select a tab to change the region to display.
[ME] tab: Switcher bank regions To select and set multiple regions, place a check mark
[User] tab: User regions beside the target regions to set.
[DME] tab: DME regions To select and set all regions, place a check mark in the
[External Device] tab: External device regions Select All checkbox.
231
• Region display 2 In the list on the left, select a copy source register.
Displays the regions registered in the register in white
characters. To select and copy multiple registers, place a check
When the [Edit Shotbox] button is pressed, the Home > mark beside the target registers to copy.
Register > Shotbox > Edit Shotbox menu (18306.11) is To select and copy all registers, place a check mark in
recalled. the Select All checkbox.
You can also press the [Select Register(s)] button and
For details, see “Creating and Editing a Shotbox” enter a register number in the numeric keypad
(page 230). window.
232
Locking a register To select and rename all registers, place a check mark
in the Select All checkbox.
1 Open the Home > Register > Shotbox > Edit Register You can also press the [Select Register(s)] button and
> Browse menu (18306.21). enter a register number in the numeric keypad
window.
2 Select the target register to lock.
3 Press the [Register Name] button.
To select and lock multiple registers, place a check
mark beside the target registers to lock. The [Rename] window appears.
To select and lock all registers, place a check mark in
the Select All checkbox. 4 Press the input field and enter a name (up to 8
You can also press the [Select Register(s)] button and characters) using the keyboard.
enter a register number in the numeric keypad
window.
Deleting a register
Note
1 Open the Home > Register > Shotbox > Edit Register
> Browse menu (18306.21).
Renaming a register
Note
1 Open the Home > Register > Shotbox > Edit Register
> Browse menu (18306.21).
233
• You can set the operation when the [RUN] button is
Executing a Shotbox pressed again during effect timeline execution.
For details, see “Setting the operation when the [RUN]
button is pressed during effect timeline execution”
(page 328).
You can execute a shotbox using the Flexi Pad control
block, utility control block, cross-point control block, or
the menu.
On the utility control block and cross-point control block, Executing a Shotbox (Utility Control
use buttons assigned with the shotbox register recall Block)
function.
You can recall a shotbox using the utility control block in
For details about assigning a function, see “Assigning a utility/shotbox operation mode.
Utility Function” (page 318).
1 Press the [UTIL/SBOX] button.
The memory recall section switches to utility/shotbox
Executing a Shotbox (Flexi Pad operation mode.
Control Block)
2 Select a bank.
You can recall a shotbox using the Flexi Pad control block
in shotbox operation mode. For details about selecting a bank, see “Selecting a
bank” (page 179).
1 Press the [SHOTBOX] button.
3 Press the button for the target register to recall.
The memory recall section switches to shotbox
operation mode. When a button assigned with a shotbox register is
The currently selected bank number and register pressed, the button is lit orange and the shotbox is
number are displayed on the top right button in the recalled.
memory recall section. When auto run is enabled, the registered effect
timeline is executed at the same time the register is
2 Select a bank. recalled.
For details about selecting a bank, see “Selecting a To execute an effect timeline
bank” (page 216). Press the [RUN] button.
When stopped by a pause, the [RUN] button is lit green.
3 Press the button for the target register to recall. Press the [RUN] button, lighting it amber, to resume effect
timeline execution.
The register name or register number is displayed in To move to the start point of an effect timeline, press the
white characters on buttons with a registered shotbox. [REWIND] button.
When pressed, the register button is lit orange and the
shotbox is recalled.
Notes
When auto run is enabled, the registered effect
timeline is executed at the same time the register is • When auto run is disabled, an effect timeline is not
recalled. executed when a shotbox register is recalled. Press the
[RUN] button to execute.
To execute an effect timeline • You can set the operation when the [RUN] button is
Press the [RUN] button. pressed again during effect timeline execution.
When stopped by a pause, the [RUN] button indication For details, see “Setting the operation when the [RUN]
changes to [PAUSE] button. When you press the [PAUSE] button is pressed during effect timeline execution”
button, the button indication returns to [RUN] button and (page 328).
effect timeline execution resumes.
To move to the start point of an effect timeline, press the
[REWIND] button.
Executing a Shotbox (Cross-Point
Notes Control Block)
• When auto run is disabled, an effect timeline is not You can recall a shotbox using a cross-point button row
executed when a shotbox register is recalled. Press the assigned with a utility/shotbox bank.
[RUN] button to execute.
234
1 Select a bank. For details, see “Setting the operation when the [RUN]
button is pressed during effect timeline execution”
The target utility/shotbox bank is assigned to a cross- (page 328).
point button row.
For details about selecting a bank, see “Selecting a
bank” (page 180).
Notes
• When auto run is disabled, an effect timeline is not
executed when a shotbox register is recalled. Press the
[Run] button to execute.
• You can set the operation when the [Run] button is
pressed again during effect timeline execution.
235
Macros
Control block
Chapter
Event
18
Overview Device control • Following operations in device/frame
block memory/clip player operation mode
- Playback
A macro is a function that saves control panel operations - Stop
- Fast forward
and menu operations in a register which can be used to - Rewind
reproduce the same operations. You can save a macro in a - Move to start point
register and then recall it as required. - Set start point
There are 250 macro registers on each control panel. - Record to VTR/disk recorder
- Set frame memory/clip player loop
Utility control block • Recall function assigned to memory
Events recall button
Control panel operations and menu operations registered • Effect timeline execution, rewind,
in a macro are called “events.” and execution direction selection
Up to 99 events can be registered in a single macro register a) In the case of an event that inserts or removes a key, the state at the time
and a total of 3750 events can be registered in all macro of event registration (key on or key off) is also registered in the macro.
registers. When a macro is executed, the event is only reproduced if the key state
matches the registered state.
Control panel operations that can be registered
Menu operations that can be registered as an
as an event
event
Control block Event Menu operations in the Home menu hierarchy.
However, the following menu operations cannot be
Cross-point control • Select cross-point
block • Recall function assigned to cross- registered.
point • Menu recall operations
• Enable/disable AUX mix • Parameter setting operations using touch control in the
• Delegation selection in cross-point analog controls window
button row (free assign mode only) (Parameter setting operations using numeric keypad
Transition control • Auto transition and cut input can be registered as an event)
block • Independent key transition auto • Parameter setting operations on the device control block
transition and key on/off a) in menu parameter operation mode
• Select next transition
• Select transition type Notes
• Enable/disable pattern limit
Flexi Pad control • Select transition type of independent • Menu operation events can be registered only when
block key transition creating/editing a macro using the menu.
• Recalling the following functions • System Configuration menu operations cannot be
- Snapshot registered as an event.
- Key snapshot
- Wipe snapshot
- DME wipe snapshot Macro attachment
- Shotbox
You can execute a macro when a control panel button or
• Effect timeline execution and rewind
fader lever is operated by assigning a macro register to the
control panel button or fader lever.
236
Macro timeline
You can execute macros in sequence by registering macro Recall register 2, and move
recall/execute actions at keyframe points on an effect to any event. Recall register 1.
timeline.
m
Macro being edited Recalled macro
Creating and Editing a Macro (register 2) (register 1)
Note
A macro cannot be executed while creating/editing a Macro in register 1 remains
macro. unchanged.
Creating a macro
Recall an empty register and register events. Auto insert mode
To include all settings information associated When creating or editing a macro with auto insert mode
with an operation when registering enabled, control panel operations and menu operations are
You can include the transition rate, cross-point, and region automatically inserted as an event.
settings information when registering a macro event. When you start creating or editing a macro with the macro
To include the settings information, you use utility execution mode set to normal execution mode, auto insert
commands assigned to the memory recall buttons in the mode is automatically enabled. In step execution mode, it
utility control block and the cross-point buttons in the is disabled.
cross-point control block.
Auto pause insert mode
“Macro AT with Rate” utility command:
In addition to the auto insert mode function, auto pause
When registering an auto transition macro event in the
insert mode automatically inserts a pause event between
transition control block, include the transition rate.
events.
“Macro AT with A/B Bus” utility command:
The time between an event being inserted and the next
When registering an auto transition macro event in the
event being inserted is set as the pause time.
transition control block, include the background
A bus/B bus cross-points.
“Macro TL with Region” utility command: Note
When registering a macro event on an effect timeline, When macros are merged, pause events are not
include the target region. automatically inserted.
Editing a macro
You can insert, modify, and delete events in a recalled Executing a Macro
macro register.
Merging macros Pausing and resuming a macro
When creating/editing a macro, you can recall a macro
Pause event
register on a control block that is not in edit mode and then
You can insert a pause event to pause macro execution.
merge the recalled macro with the macro being created/
This is useful for adjusting the event execution timing.
edited.
You can set a pause time in the range of 0 to 999 frames.
Example:
When the set pause time elapses, macro execution
If macro register 1 is recalled while editing macro register
automatically resumes.
2
When the pause time is set to “0”, macro execution does
not automatically resume. You can resume with arbitrary
timing using the take operation.
237
Note
• If operations due to events executing simultaneously
conflict with each other, the events may not be
When registering a rewind or move to start point operation reproduced with the registered settings or sequence.
as an event for an external device, you must take into • To resume all paused macros within the macros executed
account the time taken to complete execution. Adjust the simultaneously, press the button assigned with the
timing by inserting a pause event. “Macro All Take” utility command.
• To stop all macros executed simultaneously, press the
Take operation button assigned with the “Macro All Cancel” utility
This operation is used to resume execution of a paused command.
macro.
A take operation is performed using the [TAKE] button in
the Flexi Pad control block. Triggering macro execution using GPI
You can also assign the “Macro Take” utility command to input
a cross-point button in the cross-point control block and a You can recall a macro register and perform a take
memory recall button in the utility control block. operation using a GPI input.
Macro execution mode For details about GPI inputs, see “Setting a GPI Input”
The following two types of execution mode can be set. (page 332).
Notes
• In multi mode, macros are executed in normal execution
mode, regardless of the execution mode setting.
• Up to 16 macros can be executed simultaneously.
• Editing operations cannot be used for macros that are
being executed simultaneously.
238
To select bank 1: Press the [BANK1] button.
Macro Operations (Flexi To select bank 2: Press the [BANK2] button.
To select bank 0 to 25: Press the [BANK SEL] button and
Pad Control Block) enter a bank number (0 to 25) using the numeric
keypad buttons in the memory recall section.
To select the previous bank, press the [PREV BANK]
You can create and edit a macro on the Flexi Pad control button in the memory recall section.
block in macro operation mode. To select the next bank, press the [NEXT BANK] button
in the memory recall section.
Notes Selecting a register
• Menu operation events cannot be registered using the The selected bank register is displayed in the memory
Flexi Pad control block. recall section. Press the button for the target register to
• A macro cannot be created/edited using the Flexi Pad select it.
control block when the menu is in macro edit mode. The register name is displayed on buttons for registers with
• When executing a macro, if you switch to macro edit a registered macro.
mode, the macro currently being executed stops. The button color varies as follows, according to the
• A macro cannot be executed while creating/editing a register state.
macro. Gray characters: Register not containing a registered
macro
White characters: Register containing a registered macro
Lit orange: Last recalled register
Creating and Editing a Macro
Edit mode
When you press and hold the [MCRO] button and press a
Memory recall section in macro operation register button in macro operation mode, the [MCRO]
mode button is lit red and the memory recall section switches to
Pressing the [MCRO] button in the Flexi Pad control edit mode.
block, turning it on amber, switches the memory recall In edit mode, you can insert, modify, and delete events
section to macro operation mode. using the memory recall section buttons and then save the
You select registers (1 to 250) and execute take operations macro in a macro register.
using the buttons in the memory recall section. The current event number and total number of events are
To allow operations on the 250 macro registers, the Flexi displayed on the top right button.
Pad control block groups the registers. A register group is
called a bank.
There are 26 banks (0 to 25) and you display and select the
bank corresponding to the target register.
Ten registers are displayed in each bank. Bank 0 displays
register numbers 1 to 9, bank 1 displays register numbers
10 to 19, and so on. Bank 25 displays register number 250.
The currently selected bank number and register number
are displayed on the top right button in the memory recall
section.
The number of executed events and total number of events
are displayed on the bottom center button in the memory
recall section.
Note
A register number is not assigned to the bottom left button
of bank 0. You can assign any register number.
Selecting a bank
You can switch banks using the following buttons.
To select bank 0: Press the [BANK0] button.
239
• When editing a macro using the menu, the [MCRO]
UNDO button button is lit green. If a macro register is recalled using
DEL button the Flexi Pad control block, the recalled register is
merged with the register currently being edited in the
menu.
2 Select a bank.
For details about selecting a bank, see “Selecting a
bank” (page 239).
240
The macro is saved in the register. When auto insert mode is enabled, the pause event is
inserted after the selected event automatically.
To exit macro creation/editing without saving When auto insert mode is disabled, press the [INS]
Press the [EXIT] button. button to insert the pause event.
241
2 Enable auto insert mode.
Note
Macro Operations (Menu)
Registers cannot be merged when auto insert mode is
disabled. Macro edit mode
You can create and edit a macro using the Home > Register
3 Recall a register to merge. > Macro > Edit Macro menu (18307.11).
Multiple simultaneous web menu session connections are
Recall a macro register using one of the following
supported, but only one web menu session can edit a macro
buttons.
at any given time.
• Buttons with a set macro attachment (see page 253)
When an operation that would invoke edit mode is
• Cross-point buttons in the cross-point control block
performed while editing a macro in another menu session,
(see page 249)
the macro being edited in the other menu session is saved
• Memory recall buttons in the utility control block
and then the mode switches to edit mode.
(see page 249)
In macro edit mode, the following information is displayed
All events in the recalled register are inserted after the
in the header area.
selected event.
Macro Menu Enbl: When auto insert mode is disabled
during macro editing
Macro Auto Ins: When auto insert mode is enabled
during macro editing
Menu operations performed in macro edit mode are
registered in a macro as an event.
Notes
• A macro cannot be created/edited using the menu when
the Flexi Pad control block macro operation mode is in
edit mode.
• When executing a macro, if you switch to macro edit
mode, the macro currently being executed stops.
• A macro cannot be executed while creating/editing a
macro.
• Multiple simultaneous web menu session connections
are supported, but only one of the following pop-up
windows can be displayed at any given time.
Whenever any pop-up window is displayed, the window
previously opened using another menu session is closed.
- [Recall/Store Register] window:
Displayed using the [Recall/Store] button on the
[Effect Timeline Recall/Store] taskbar, [Effect
Timeline Edit] taskbar, or [Snapshot] taskbar
- [Edit Timeline] window:
Displayed using the [All Edit Options] button on the
[Effect Timeline Edit] taskbar
- [Edit Macro Event] window:
Displayed using the [All Edit Options] button in the
[Edit] group in the Home > Register > Macro > Edit
Macro menu (18307.11)
242
2 Press the [Register No.] button and enter a register
number in the numeric keypad window. Editing a Macro Event
When creating, select an empty register. When editing, Select the target register to edit in the Home > Register >
select the target register to edit. Macro > Edit Macro menu (18307.11) to switch to edit
Macro edit mode is activated. mode and edit an event. When finished editing, save the
register.
When editing a macro in another menu session
Set the [Edit Enable] button to the on state. Check the For details, see “Creating and Editing a Macro”
message and press [OK] to switch to macro edit mode. (page 242).
3 If required, set auto insert mode. You can edit an event using the following menu or the
taskbar.
To enable auto insert mode, set the [Auto Insert]
button in the [Edit] group to the on state. Home > Register > Macro > Edit Macro menu
To disable auto insert mode, set the [Auto Insert] (18307.11)
button in the [Edit] group to the off state. Event list at the top:
For details about auto insert mode, see “Auto insert Displays the events registered in the selected register.
mode” (page 237). Select an event insertion position and target event to
edit from the list.
You can check the following information.
Notes
• Number and name of register being edited
• Auto pause insert mode cannot be set using the • Event number
menu. • Event type
• Pressing the [All Edit Options] button in the [Edit] Displays “Event” or “Continue.”
group displays the [Edit Macro Event] window. You • Symbol
can also set auto insert mode using the [Auto Insert] Displays the symbol name of an event.
button in the [Edit Macro Event] window. • Data
Displays the parameter setting values.
4 Register/edit events. • Parameters
Displays the selected event number and the
When creating a macro configured parameter names below the list.
Create and register events. Operation buttons at the bottom:
For details about registering events, see “Inserting an Perform edit operations using the [Add New Event]
event” (page 241). button, [Edit Event] button, and buttons in the [Edit]
group.
You can also register pause events. Pressing the [All Edit Options] button in the [Edit]
For details about registering pause events, see group displays the [Edit Macro Event] window.
“Inserting a pause event” (page 245). The buttons used for editing are shown on the left and
a numeric keypad area is shown on the right in the
Repeat the operation as required to register events. [Edit Macro Event] window.
When editing a macro [Macro Edit] taskbar
Perform event edit operations. You can display the following information and perform the
For details, see “Editing a Macro Event” (page 243). following operations using the [Macro Edit] taskbar.
• Number and name of register being edited
5 Press the [Store] button and enter the target register • Selected event number and total number of events
number in which to save in the numeric keypad • Current event symbol and data
window. A “…” suffix is displayed when the whole data cannot
be displayed.
The currently recalled register number is displayed in Press the event data display to display the whole event
the numeric keypad window. To select another data. To return to the previous display, press [OK].
register, enter a register number. • [Event – Insert After] button
Press [Enter] to confirm to save the created/edited Inserts the current event after the selected event.
macro in the register. • [Edit Macro] button
Recalls the Home > Register > Macro > Edit Macro
To exit macro edit mode without saving
menu (18307.11).
Press the [Edit Enable] button, check the message,
then press [OK].
243
Event structure Note
A macro event consists of an “Event” or “Continue” type,
symbol, and parameters. When inserting “Continue,” only the symbol that is the
Specify the event type using “Event” or “Continue.” Use same as the event at the selected insertion position can
“Continue” when you want to add another parameter to the be set.
symbol and parameters set for “Event.”
Select a type of event according to the symbol and specify 6 Press [OK].
the required data using the parameters.
The required parameter buttons for the selected
For details about symbols and parameters, see “Events symbol are added to the [Symbol/Parameter] group in
and Symbols” (page 377) and “Symbols and Parameters” the [Add New Event] window.
(page 378).
7 Set the parameters.
244
When auto insert mode is enabled, the menu operation Modify the “Event” or “Continue” type, symbol, and
is inserted as an event after the selected event parameters in the same way as when creating an event
automatically. in the [Add New Event] window.
When auto insert mode is disabled, press the [Event - For details, see “Inserting an event” (page 244).
Insert After] button to insert the menu operation as an
event. 4 Press [OK] in the [Edit Event] window.
2 Press the [Pause] button in the [Edit] group and enter a Note
pause time in the numeric keypad window.
You can also select and replace multiple events.
Note For details, see “Selecting multiple events”
(page 246).
You can also set this using the [Pause] button in the
[Edit Macro Event] window. Enter a pause time in the
numeric keypad area. Deleting an event
3 Press [Enter]. 1 In the event list, select the target event to delete.
When auto insert mode is enabled, the pause event is 2 Press the [Delete] button in the [Edit] group.
inserted after the selected event automatically.
When auto insert mode is disabled, press the [Event - The selected event is deleted.
Insert After] button to insert the pause event.
Notes
Note
• You can also use the [Delete] button in the [Edit
You can insert before or after the selected event using Macro Event] window.
the [Insert Before] button or [Insert After] button in the • You can also select and delete multiple events.
[Edit Macro Event] window. For details, see “Selecting multiple events”
(page 246).
Modifying an event To move an event
Delete an event, select the event at the insertion position,
Note and press the [Paste Before] button or [Paste After] button
in the [Edit Macro Event] window.
Menu operation events cannot be modified. The deleted event is inserted before or after the selected
position.
1 In the event list, select the target event to modify.
245
3 In the event list, select the event at the insertion To change the number of the first event in the specified
position. range, press [Clear]. Enter the number of the first
event, press [Enter], and then enter the number of the
4 Press the [Paste Before] button or [Paste After] button last event.
in the [Edit Macro Event] window. Enter a “.” (period) to specify a range from the first
event to the last event.
The copied event is inserted before or after the selected
event. 4 Press [Enter].
246
To select and copy multiple registers, place a check Locking a register
mark beside the target registers to copy.
To select and copy all registers, place a check mark in 1 Open the Home > Register > Macro > Edit Register >
the Select All checkbox. Browse menu (18307.21).
You can also press the [Select Register(s)] button and
enter a register number in the numeric keypad 2 Select the target register to lock.
window.
To select and lock multiple registers, place a check
3 In the list on the right, select a copy destination mark beside the target registers to lock.
register. To select and lock all registers, place a check mark in
the Select All checkbox.
When multiple registers are selected, select the first You can also press the [Select Register(s)] button and
copy destination register. enter a register number in the numeric keypad
You can also press the [Select Destination] button and window.
enter a register number in the numeric keypad
window. 3 Press the [Lock] button.
The copy destination of the first register selected on
the left is the first register selected on the right, and the To release the lock
subsequent registers on the right in the same relative Select the target register to unlock and press the [Unlock]
positions as the selected registers on the left become button.
copy destinations. The first register on the right is
shown in light blue, and the subsequent copy Deleting a register
destination registers are shown in blue gray.
For details, see “Copying a register” (page 246). 4 Check the message, then press [OK].
247
To select and rename all registers, place a check mark
in the Select All checkbox.
You can also press the [Select Register(s)] button and
Executing a Macro
enter a register number in the numeric keypad
window.
You can execute a macro using the Flexi Pad control
block, utility control block, or cross-point control block.
3 Press the [Register Name] button and enter a name (up
On the utility control block and cross-point control block,
to 8 characters) using the keyboard.
use buttons assigned with the macro register recall
function.
Notes
• Multi mode is disabled if a macro register is recalled
using the Flexi Pad control block. Only one macro can be
executed at a time.
For details about multi mode, see “Executing multiple
macros simultaneously (multi mode)” (page 238).
• If the same macro or another macro is recalled during
macro execution or when the macro is stopped, the
operation varies depending on the settings.
For details about settings, see “Setting the Macro
Mode” (page 328).
• Events registered in a macro are executed according to
the setup and the device configuration in force when the
events were registered. If the state has changed since
registration, the contents of the macro may not be
reproduced correctly when the macro is recalled.
• When executing a macro, if you switch to macro edit
mode, the macro currently being executed stops.
• A macro cannot be executed while creating/editing a
macro.
2 Select a bank.
248
For details about selecting a bank, see “Selecting a The memory recall section switches to utility/shotbox
bank” (page 239). operation mode.
3 Press the button for the target register to recall. 2 Select a bank.
For details about selecting a register, see “Selecting a For details about selecting a bank, see “Selecting a
register” (page 239). bank” (page 179).
The register button is lit orange and the macro is 3 Press the button for the target register to recall.
executed.
The number of executed events and total number of When a button assigned with a macro register is
events are displayed on the bottom center button in the pressed, the button is lit orange and the macro is
memory recall section. recalled.
In normal execution mode, the macro is executed
To resume when paused by a pause event automatically.
When paused by a pause event with a specified pause time
of “0”, the [TAKE] button is displayed in the memory
recall section.
Press the [TAKE] button to resume macro execution. Executing a Macro (Cross-Point
Control Block)
Executing a macro in step execution mode You can recall a macro using a cross-point button row
assigned with a utility/shotbox bank.
1 Press the [MCRO] button.
The [MCRO] button is lit amber, and the memory 1 Select a bank.
recall section switches to macro operation mode. The target utility/shotbox bank is assigned to a cross-
point button row.
2 Select a bank.
For details about selecting a bank, see “Selecting a
For details about selecting a bank, see “Selecting a bank” (page 180).
bank” (page 239).
2 Press the button for the target register to recall.
3 Press the button for the target register to recall.
When a button assigned with a macro register is
For details about selecting a register, see “Selecting a pressed, the button is lit amber and the macro is
register” (page 239). recalled.
In normal execution mode, the macro is executed
The register button is lit orange.
automatically.
4 Press the [TAKE] button in the memory recall section.
A single event registered in the macro is executed, then
execution stops.
Press the [TAKE] button to execute events one at a
time.
The number of executed events and total number of
events are displayed on the bottom center button in the
memory recall section.
249
of the 1st row delegation buttons, the macro attachment
Macro Attachments setting is deleted.
• After setting a macro attachment to an assignable button,
if you change the button setting, the macro attachment
setting is deleted.
Overview • After setting a macro attachment to a cross-point button
in the cross-point control block, if you change the
A macro attachment is a function whereby a macro register function assignment of the button, the macro attachment
is assigned to a control panel button or a particular position setting is deleted.
of a fader lever, linking the execution of the button
function or a fader lever operation with a macro execution.
Executing a macro attachment
To execute a macro assigned to a button or fader lever
Macro attachment link mode using a macro attachment, macro attachments must be
The following three link modes are available. enabled. The enable/disable setting is switched using the
Pre-macro mode: The macro is executed first, and then the [MCRO ATTCH ENBL] button in the cross-point control
button function is executed. block or a button assigned with the “Macro Attachment
Post-macro mode: The button function is executed first, Enbl” utility command.
and then the macro is executed. You can also permanently enable or disable macro
Macro only mode: The button function is not executed, and attachments.
the macro only is executed.
For details about settings, see “Setting the macro
attachment enable/disable configuration mode”
Setting a macro attachment (page 329).
Only one register can be assigned to a button.
You can set a macro attachment to the following buttons.
• After setting a macro attachment to a 2nd row cross- 2 Assign a macro register to a button.
point button in the cross-point control block in key/AUX
bus delegation mode, if you change the bus assignment
250
To assign in pre-macro mode For details about selecting a register, see “Selecting a
Press and hold the [PRE MACRO] button in the cross- macro register” (page 250).
point control block and press the assignment target
button. 2 Move the fader lever to the position where you want to
set a macro attachment.
To assign in post-macro mode
Press and hold the [POST MACRO] button in the 3 Assign a macro register to the fader lever.
cross-point control block and press the assignment
target button. To assign to a position other than the operation
start point/operation end point
To assign in macro only mode Press and hold the [PRE MACRO] button or [POST
Simultaneously press and hold both the [PRE MACRO] button in the cross-point control block and
MACRO] button and [POST MACRO] button in the press the [PRIOR SET] button or [LIMIT SET] button
cross-point control block and press the assignment in the transition control block.
target button.
To assign to the operation start point
Notes Press and hold the [PRE MACRO] button in the cross-
point control block and press the [PRIOR SET] button
• When a button assigned with a macro attachment is or [LIMIT SET] button in the transition control block.
selected, the newest configured macro attachment
setting becomes enabled. To assign to the operation end point
• When setting a macro attachment, the button Press and hold the [POST MACRO] button in the
function is not executed. You can also configure a cross-point control block and press the [PRIOR SET]
setting such that the button function is executed. button or [LIMIT SET] button in the transition control
For details about settings, see “Setting the operation block.
of buttons when configuring a macro attachment”
(page 329). To check the macro attachment setting status
You can check the fader lever position at which the macro
To check the macro attachment setting status attachment is set.
You can check the cross-point buttons in a cross-point While the [PRE MACRO] button or [POST MACRO]
control block for which a macro attachment is set. button in the cross-point control block is pressed, the status
While the [PRE MACRO] button is pressed, the buttons is displayed in the transition control block as follows.
for which a macro attachment is set flash as follows. Transition indicator: The indicators at the position where
Buttons set in pre-macro mode: Flash amber the macro attachment is set and at both ends are lit.
Buttons set in macro only mode: Flash green Display on the right: Displays the position where the
While the [POST MACRO] button is pressed, the buttons macro attachment is set as a percentage (fader lever
for which a macro attachment is set flash as follows. operation start position is 0%, operation end position
Buttons set in post-macro mode: Flash amber is 100%).
Buttons set in macro only mode: Flash green
Releasing a macro attachment
Setting a macro attachment to a fader lever
To release a macro attachment set to a button
You can set a macro attachment to any particular position Press and hold the [PRE MACRO] button or [POST
of a fader lever in the transition control block. MACRO] button in the cross-point control block and press
the target button to release.
Note
To release a macro attachment set to a fader lever
Macro link mode is enabled only when a macro attachment Press and hold the [PRE MACRO] button or [POST
is set to the operation start point (0%) or operation end MACRO] button in the cross-point control block and press
point (100%) of the fader lever. the [PRIOR SET] button or [LIMIT SET] button in the
To set at the operation start point, assign a macro register transition control block.
in pre-macro mode. To set at the operation end point,
assign a macro register in post-macro mode.
Note
It is not possible to set a macro attachment in macro only
mode. You can also release a macro attachment setting using the
menu.
1 Select a macro register.
For details, see “Displaying a Macro Attachment List”
(page 252).
251
Setting the macro attachment A list of the macro attachments set to the buttons of the
configuration mode of a cross-point button selected control block is displayed.
The following two modes can be selected for a macro You can check the following information in a macro
attachment set to a cross-point button. attachment list.
Button number mode: Assign a macro attachment for the • Block name
combination of bus and button number. Displays the name of the control block on which macro
Pair number mode: Assign a macro attachment for the attachments are set.
combination of bus and pair number. • Buttons to which a macro attachment is set
• Register number
Notes • Register name
• If the macro attachment configuration mode is changed, • Link mode
the macro attachment assigned to a cross-point button is
deleted. For details about macro attachment lists, see “Macro
• In pair number mode, the following occurs. Attachment Lists” (page 384).
- If the same pair number is assigned to multiple cross-
point buttons, pressing any of the buttons executes the Note
macros of all buttons to which the same pair number is
assigned. Macro attachments set to the following buttons in the
- If the same pair number is assigned to multiple cross- cross-point control block may not be displayed in the list.
point buttons, releasing the macro attachment of any of • DME utility 1 bus and 2 bus cross-point buttons in utility
the buttons releases the macro attachment of all bus mode
buttons to which the same pair number is assigned. • DME utility 1 bus and 2 bus cross-point buttons in key/
- If you change the pair number assignment to a AUX bus delegation mode
different cross-point button, the macro attachment
setting is also transferred. Releasing a macro attachment
• When macro attachment data is loaded, the button
number mode or pair number mode setting is 1 Open the Home > Register > Macro > Attachment
overwritten. menu (18307.31).
1 Open the Home > Register > Macro > Attachment 2 Display the target control block.
menu (18307.31).
Select a tab to change the control block to display.
2 In the [Xpt Attachment Mode] group, select a [M/E-1] tab to [M/E-5] tab, [P/P] tab: Switcher bank
configuration mode. cross-point control block and transition control
block
Button Mode: Button number mode [Trackball] tab: Device control block
Pair Mode: Pair number mode
3 Select the target button to release.
3 Check the message, then press [OK].
To select and release multiple buttons, place a check
mark beside the target buttons to release.
To select and release all buttons, place a check mark in
Displaying a Macro Attachment List the Select All checkbox.
You can check the information for a button/fader lever to
which a macro attachment is set in list view. 4 Press the [Delete] button.
1 Open the Home > Register > Macro > Attachment 5 Check the message, then press [OK].
menu (18307.31).
Releasing macro attachments on all
2 Display the target control block. control blocks
Select a tab to change the control block to display.
[M/E-1] tab to [M/E-5] tab, [P/P] tab: Switcher bank 1 Open the Home > Register > Macro > Attachment
cross-point control block and transition control menu (18307.31).
block
[Trackball] tab: Device control block 2 Press the [All Clear] button.
252
3 Check the message, then press [OK]. Note
You can also permanently enable or disable macro
Executing a Macro Assigned in a attachments.
Macro Attachment For details about settings, see “Setting the macro
attachment enable/disable configuration mode”
You can execute a macro assigned to a control panel button (page 329).
or fader lever by enabling macro attachments.
Notes
Executing a macro assigned to a button
• When set to multi mode, simultaneous execution of Note
multiple macros is supported using the cross-point
buttons in the cross-point control block. Multi mode is When macro attachments are enabled, the cross-point
disabled if any other buttons or fader levers are operated. buttons in a cross-point control block for which a macro
For details about multi mode, see “Executing multiple attachment is set are lit green. You can also configure a
macros simultaneously (multi mode)” (page 238). setting so the buttons do not light up.
• If the same button is pressed twice during macro
execution or when the macro is stopped, or if another For details about settings, see “Lighting buttons
macro is recalled, the following operation depends on configured with a macro attachment” (page 329).
the settings.
For details about settings, see “Setting the Macro 1 Enable macro attachments.
Mode” (page 328).
For details, see “Enabling macro attachments”
• Events registered in a macro are executed according to
(page 253).
the setup and the device configuration in force when the
events were registered. If the state has changed since
registration, the contents of the macro may not be
2 Press the button with a set macro attachment.
reproduced correctly when the macro is recalled. The macro is executed according to the link mode.
• When executing a macro, if you switch to macro edit During macro execution, the selected button flashes.
mode, the macro currently being executed stops.
• When creating/editing a macro, pressing a button or
fader lever for which a macro attachment is set does not Executing a macro assigned to a fader
execute the macro. lever
You can enable/disable macro attachments using the For details, see “Enabling macro attachments”
following buttons. (page 253).
To enable macro attachments assigned on a • If you do not move the fader lever to the operation
control block separate from a switcher bank end position, the macro cannot be executed again.
Enable using the following buttons assigned with the • If executing a 2-stroke preset color mix, the macro is
“Macro Attachment Enbl” utility command. executed by fader lever operation in the first stroke.
• Press a memory recall button in the utility control block, The macro is not executed by fader lever operation
turning it on orange. in the second stroke.
To disable, press the button, turning it on dark blue.
• Press a cross-point button in the cross-point control
block, turning it on amber.
To disable, press the button, turning it off.
253
1 Open the Home > Register > Macro > Timeline >
Macro Timelines Action menu (18307.41).
Setting an action
You can configure an action at a keyframe point on an
effect timeline.
254
File Management
Default package
Chapter 19
Overview The default package is a package named
“!Default_Package”. The default package cannot be
deleted.
You can save setup and register data in switcher storage
and then recall it as required. Loading/saving
You can perform load and save operations for each
Categories category. You can also perform operations for a group of
multiple categories.
Setup data and register data are classified by setting and
Select categories, create setup data and register data
function.
packages, and then save the packages in storage.
You can perform operations on files in the following
To recall the setup data and register data, select and load
categories.
files from packages saved in storage. The setup data and
Setup data categories register data saved in the files are then applied.
System: System settings You can also prevent the loading of files for each category.
Xpt Assign: Cross-point settings
Switcher: Switcher settings Importing/exporting
Panel: Control panel settings
External Device: External device settings You can import/export package archive files between
Router/Tally: Router/tally settings switcher storage and a computer.
Link: Link settings
Initial Status: Initial status data Note
Packages stored in switcher storage may become unusable
For details about initial status, see “Setting Startup”
in the event of a storage failure. Save a backup of
(page 282).
important files on a computer or on external media
connected to a computer.
Register data categories
Effect Timeline: Effect timeline register data
Snapshot: Snapshot register data
Key Snapshot: Key snapshot register data
Wipe Snapshot: Wipe snapshot register data
DME Wipe Snapshot: DME wipe snapshot register data
Shotbox: Shotbox register data
Macro: Macro register data
Macro Attachment: Macro attachment data
Packages
Setup data and register data files are saved in switcher
storage as a package.
You can create a package with files in a single category or
files in multiple categories.
You can add tags to packages for efficient identification
and management.
255
e Select All checkbox
Package Operations f Checkbox
g Package name
Displaying a Package
h Package modification date and time
Open the Home > File > Package > Browse menu
(10101.11). i Package size
A list of packages appears.
j Tags added to package
e d c b a
k Lock icon
A lock icon is displayed when a package is locked.
l Properties display
Displays the properties of the package with focus.
You can check the following information.
• Package name
• Lock icon
• Package modification date and time
• Package size
• Tags added to package
• Categories included in the package
• Memo
f g h i j k l Sorting
You can press a display item title to sort the display.
Sorting switches between ascending and descending order
a Storage free space each time you press a title.
Displays the available space in storage where packages are When sorted in ascending or descending order, [v]
saved. (ascending) or [V] (descending) is displayed on the right
side of the title.
b [Refresh] button Name: Sort by package name
Updates the list view by the configured criteria using the Date/Time: Sort by modification date and time
[Filter] button or [Search] button. Size: Sort by size
When the list view needs to be updated due to changes to Tags: Sort by first tag name
a package, for example, the [Refresh] button icon is lit
blue. Filtering by criteria
Press the [Filter] button and set the filter criteria in the
c [Search] button
criteria setup window.
Filters the list view by character string search criteria.
Only packages that match the selected tag and category are
When character string search criteria is configured, the
displayed.
[Search] button icon is lit blue.
d [Filter] button
Filters the list view by tag and category selection criteria.
When selection criteria is configured, the [Filter] button
icon is lit blue.
256
Specifying search criteria
You can specify an AND condition or OR condition to
search for multiple character strings.
Note
An AND condition search only matches within each item
(package name, tag, memo). You cannot search across
multiple items.
Selecting a package
Searching
Select the target package for operation from the list view.
Press the [Search] button and enter a character string to The selected package is highlighted light blue and has
search for in the search window. focus, with the package properties shown on the right.
Only packages containing the entered character string are To select multiple packages, place a check mark beside the
displayed. target packages to select.
To select all displayed packages, place a check mark in the
Select All checkbox.
Copying a Package
You can duplicate a package.
1 Open the Home > File > Package > Browse menu
(10101.11).
Press the input field in the search window and enter a
character string to search for using the keyboard. 2 Select the target package to copy.
Press [OK] to apply the character string to search for.
The following items can be searched. To select and copy multiple packages, place a check
• Package name mark beside the target packages to copy.
• Tags To select and copy all packages, place a check mark in
• Memo the Select All checkbox.
257
3 Press the [Copy] button. Note
4 Check the message, then press [OK]. If an unlocked package is selected as the target for
operation, the unlocked status is retained.
For the duplicate packages, a copy count (underscore
and copy number) is added to the package name.
Editing Package Properties
Note
Tags and memos added to a package are also copied. Note
2 Select the target package to delete. 3 Press the [Edit Properties] button.
To select and delete multiple packages, place a check The [Edit Properties] window appears.
mark beside the target packages to delete.
To select and delete all packages, place a check mark 4 Press the [Name] button and enter a package name (up
in the Select All checkbox. to 64 characters) using the keyboard.
4 Check the message, then press [OK]. • When multiple packages are selected, the package
names cannot be edited.
• If the default package is renamed, it becomes an
Locking a Package ordinary package and a default package no longer
exists.
1 Open the Home > File > Package > Browse menu 5 Select tags to add to a package in [Tags].
(10101.11).
Place a check mark for each tag to add.
2 Select the target package to lock.
Note
To select and lock multiple packages, place a check
mark beside the target packages to lock. When multiple packages are selected, clearing a check
To select and lock all packages, place a check mark in mark for a tag removes the tag from all packages.
the Select All checkbox. Placing a check mark for a tag adds the tag to all
packages.
3 Press the [Lock] button.
To create a tag
Press the [New Tag] button to display the [New Tag]
Note
window.
If a locked package is selected as the target for Press the input field and enter a tag name (up to 24
operation, the locked status is retained. characters) using the keyboard, then press [OK].
To release the lock 6 Press the [Memo] button and enter a memo (up to 255
Select the target package to unlock and press the [Unlock] characters) using the keyboard.
button.
258
Note
A list of packages is shown on the left, and the
properties of the selected package are shown on the
When multiple packages are selected, the memo of all right.
packages will have the same description.
To edit properties
7 Press [OK]. Press the [Edit Properties] button.
For details about editing properties, see “Editing
Package Properties” (page 258).
Importing/Exporting a Package
Archive File 2 Select a package to export.
To select and export multiple packages, place a check
You can create a package archive file and then import/ mark beside the target packages to export.
export it between switcher storage and a computer. To select and export all displayed packages, place a
check mark in the Select All checkbox.
Importing a package archive file
3 Press the [Export Now] button.
Note 4 Check the message, then press [OK].
Only archive files that have been exported using the Home
An archive file for the selected package is exported.
> File > Package > Import/Export > Export menu
The file name extension for an archive file is “.spz”.
(10101.22) can be imported.
1 Open the Home > File > Package > Import/Export >
Import menu (10101.21).
Note
If a default package is imported, it overwrites the
current default package.
1 Open the Home > File > Package > Import/Export >
Export menu (10101.22).
259
Saving Files
Batch File Operations
Note
You can select multiple categories and perform batch Files cannot be saved in a locked package.
operations on setup data and register data files.
1 Open the Home > File > All > Load/Save > Save menu
(10102.12).
Loading Files The name of the most recently loaded package and the
free space in storage are displayed at the top right.
Note
1 Open the Home > File > All > Load/Save > Load menu 3 Select a package and press [OK].
(10102.11).
To create a new package
The name of the most recently loaded package and the Press the [New Package] button to display the [New
free space in storage are displayed at the top right. Package] window.
Specify a package name, tags, and memo in the same
2 Press the [Select] button in the [Package] group. way as in [Edit Properties] window.
The [Select Package] window appears. For details, see “Editing Package Properties”
(page 258).
3 Select a package and press [OK].
To select the default package
To select the default package Press the [Default Package] button.
Press the [Default Package] button. If there is no default package, a new default package is
created.
4 Select the target category to load.
4 Select the target category to save.
To select a setup data category, select a button in the
[Setup] group. To select a setup data category, select a button in the
To select a register data category, select a button in the [Setup] group.
[Register] group. To select a register data category, select a button in the
To select all categories, set the [All Categories] button [Register] group.
to the on state. To select all categories, set the [All Categories] button
to the on state.
Note
5 Press the [Save] button.
The categories saved in the selected package are
displayed in white characters in the [Package] group 6 Check the message, then press [OK].
category display area.
The files in the categories included in the selected The files in the selected categories are saved in the
package become the target for loading. package.
6 Check the message, then press [OK]. If the selected package already contains the same
categories, the files will be overwritten.
The files in the selected categories are loaded.
To delete register data before loading files
You can delete all current register data when loading Copying Files
register data.
You can copy files in each category between packages.
Set the [Clear Regis. Before Load] button in the [Switcher]
group to the on state.
260
Note
7 Press the [Copy] button.
Files cannot be copied to a locked package. 8 Check the message, then press [OK].
1 Open the Home > File > All > Copy > Copy menu The files in the selected categories are copied.
(10102.21).
Note
The categories saved in the selected copy source and
copy destination packages are displayed in white
characters in the [Source Package] group/[Target
Package] group category display area.
The files in the categories included in the copy source
package become the target for copying.
If the copy destination package already contains the
same categories, the files will be overwritten.
261
This section describes the system setup data menu as an
Setup Data File example.
Operations
Loading a File
262
To create a new package For details, see “Editing Package Properties”
Press the [New Package] button to display the [New (page 258).
Package] window.
Specify a package name, tags, and memo in the same To select the default package
way as in [Edit Properties] window. Press the [Default Package] button.
For details, see “Editing Package Properties” 6 Press the [Copy] button.
(page 258).
To select the default package 7 Check the message, then press [OK].
Press the [Default Package] button. The file is copied.
Note
2 Press the [Select] button in the [Package] group.
Files cannot be copied to a locked package. The [Select Package] window appears.
1 Open the Home > File > Setup > System > Copy menu 3 Select a package that includes the target file to delete
(10103.13). and press [OK].
To select the default package
2 Press the [Select] button in the [Source Package] Press the [Default Package] button.
group.
The [Select Package] window appears. 4 Press the [Delete] button.
3 Select a copy source package and press [OK]. 5 Check the message, then press [OK].
263
3 Select a package that includes the target file to rename
and press [OK].
Register Data File
To select the default package
Press the [Default Package] button. Operations
4 Press the [Rename] button.
The [Rename] window appears. Target Category Menus
Register data file operations are performed using the Home
5 Press the input field and enter a file name (up to 8
> File > Register menu.
characters) using the keyboard.
The following submenus are used for each category.
6 Press [OK]. Categories Level 4 > level 5 Menu
number
The file is renamed.
Effect timeline Effect Timeline > Load 10104.11
Effect Timeline > Save 10104.12
Effect Timeline > Copy 10104.13
Effect Timeline > Browse 10104.14
Files
Snapshot Snapshot > Load 10104.21
Snapshot > Save 10104.22
Snapshot > Copy 10104.23
Snapshot > Browse Files 10104.24
Key snapshot Key Snapshot > Load 10104.31
Key Snapshot > Save 10104.32
Key Snapshot > Copy 10104.33
Key Snapshot > Browse 10104.34
Files
Wipe snapshot Wipe Snapshot > Load 10104.41
Wipe Snapshot > Save 10104.42
Wipe Snapshot > Copy 10104.43
Wipe Snapshot > 10104.44
Browse Files
DME wipe DME Wipe Snapshot > 10104.51
snapshot Load
DME Wipe Snapshot > 10104.52
Save
DME Wipe Snapshot > 10104.53
Copy
DME Wipe Snapshot > 10104.54
Browse Files
Shotbox Shotbox > Load 10104.61
Shotbox > Save 10104.62
Shotbox > Copy 10104.63
Shotbox > Browse Files 10104.64
Macro Macro > Load 10104.71
Macro > Save 10104.72
Macro > Copy 10104.73
Macro > Browse Files 10104.74
264
Categories Level 4 > level 5 Menu Note
number
Macro attachment Macro Attachment > 10104.81
Selection of a file is not required in the macro
Load attachment category as there is only one file.
Macro Attachment > 10104.82
Save 6 In the [Switcher] group list, select a load destination
register.
Macro Attachment > 10104.83
Copy When multiple files are selected, select the first load
Macro Attachment > 10104.84 destination register.
Browse Files You can also press the [Select Destination] button and
enter a register number in the numeric keypad
This section describes the menu for effect timeline register
window.
data as an example.
The load destination of the first file selected in the
[Package] group is the first register selected in the
[Switcher] group, and the subsequent registers in the
Loading a File [Switcher] group in the same relative positions as the
selected files in the [Package] group become load
You can select files from a package to load into registers. destinations. The first register in the [Switcher] group
is shown in light blue, and the subsequent load
Notes destination registers are shown in blue gray.
• Files in categories where loading is locked cannot be
loaded. Note
• Files cannot be loaded into a locked register. Selection of a register is not required in the macro
attachment category.
1 Open the Home > File > Register > Effect Timeline >
Load menu (10104.11). 7 Press the [Load] button.
The name of the most recently loaded package and the
free space in storage are displayed at the top right. 8 Check the message, then press [OK].
The files are loaded into the registers.
2 Select a region.
To display the register view/edit menu
The regions that can be selected vary depending on the A list of registers is displayed in the [Switcher] group.
category. Press the [Browse Multi Region] button to recall the
For details, see “To select a region” (page 265). register view/edit menu for each category.
For the effect timeline category, the Home > Register >
Note
Effect Timeline > Edit Register > Browse Multi Rgn menu
(18301.31) is recalled.
Selection of a region is not required in the shotbox,
macro, and macro attachment categories. Note
3 Press the [Select] button in the [Package] group. For the key snapshot, wipe snapshot, DME wipe snapshot,
shotbox, and macro categories, press the [Browse] button.
The [Select Package] window appears. For the macro attachment category, press the [Attachment]
button.
4 Select a package and press [OK].
To display the file view/edit menu
To select the default package The list of files included in the selected package is
Press the [Default Package] button. displayed in the [Package] group.
Press the [Browse Files] button to recall the file view/edit
5 In the [Package] group list, select the target file to load. menu for each category.
For the effect timeline category, the Home > File >
To select and load multiple files, place a check mark
Register > Effect Timeline > Browse Files menu
beside the target files to load.
(10104.14) is recalled.
To select and load all files, place a check mark in the
Select All checkbox. To select a region
You can also press the [Select File(s)] button and enter The region selection status is displayed in the [Region]
a file number in the numeric keypad window. group region display section.
265
The selected regions are displayed in white characters. The 3 In the [Switcher] group list, select the target register to
reference region is displayed inverted. save.
Press the [Select] button in the [Region] group, select a
region in the [Select Region] window, and press [OK]. To select and save multiple registers, place a check
Effect timeline/snapshot region selection: mark beside the target registers to save.
In the [Select Region] window, set the button for the To select and save all registers, place a check mark in
region to select to the on state. the Select All checkbox.
Select a tab to change the region to display. You can also press the [Select Register(s)] button and
[ME] tab: Switcher bank regions enter a register number in the numeric keypad
[User] tab: User regions window.
[DME] tab: DME regions
[External Device] tab: External device regions Note
To select all regions, set the [All Regions] button to the Selection of a register is not required in the macro
on state. attachment category as there is only one register.
Key snapshot region selection:
In the [Select Region] window, set the button for the 4 Press the [Select] button in the [Package] group.
key to select to the on state.
To select all keys, set the [All Regions] button to the The [Select Package] window appears.
on state.
Wipe snapshot/DME wipe snapshot region selection: 5 Select a package and press [OK].
In the [Select Region] window, set the button for the
switcher bank to select to the on state. To create a new package
To select all switcher banks, set the [All Regions] Press the [New Package] button to display the [New
button to the on state. Package] window.
Specify a package name, tags, and memo in the same
way as in [Edit Properties] window.
Note
For details, see “Editing Package Properties”
The register names/file names of the reference region are (page 258).
displayed in the register/file list.
The number of regions for which data is saved in a register/ To select the default package
file is displayed in [Item(s)]. Press the [Default Package] button.
A lock icon is displayed for a register when the register in
the selected region is locked. 6 In the [Package] group list, select a save destination
file.
When multiple files are selected, select the first save
Saving a File destination file.
You can also press the [Select Destination] button and
Note enter a file number in the numeric keypad window.
The save destination of the first register selected in the
Files cannot be saved in a locked package.
[Switcher] group is the first file selected in the
[Package] group, and the subsequent files in the
1 Open the Home > File > Register > Effect Timeline >
[Package] group in the same relative positions as the
Save menu (10104.12).
selected registers in the [Switcher] group become save
The name of the most recently loaded package and the destinations. The first file in the [Package] group is
free space in storage are displayed at the top right. shown in light blue, and the subsequent save
destination files are shown in blue gray.
2 Select a region.
Note
The regions that can be selected vary depending on the
category. Selection of a file is not required in the macro
attachment category.
For details, see “To select a region” (page 265).
7 Press the [Save] button.
Note
Selection of a region is not required in the shotbox, 8 Check the message, then press [OK].
macro, and macro attachment categories. The files are saved in the selected package.
266
To display the register view/edit menu To select and copy multiple files, place a check mark
A list of registers is displayed in the [Switcher] group. beside the target files to copy.
Press the [Browse Multi Region] button to recall the To select and copy all files, place a check mark in the
register view/edit menu for each category. Select All checkbox.
For the effect timeline category, the Home > Register > You can also press the [Select File(s)] button and enter
Effect Timeline > Edit Register > Browse Multi Rgn menu a file number in the numeric keypad window.
(18301.31) is recalled.
Note
Note
Selection of a file is not required in the macro
For the key snapshot, wipe snapshot, DME wipe snapshot, attachment category as there is only one file.
shotbox, and macro categories, press the [Browse] button.
For the macro attachment category, press the [Attachment] 6 Press the [Select] button in the [Target Package]
button. group.
To display the file view/edit menu The [Select Package] window appears.
The list of files included in the selected package is
displayed in the [Package] group. 7 Select a copy destination package and press [OK].
Press the [Browse Files] button to recall the file view/edit
menu for each category. To create a new package
For the effect timeline category, the Home > File > Press the [New Package] button to display the [New
Register > Effect Timeline > Browse Files menu Package] window.
(10104.14) is recalled. Specify a package name, tags, and memo in the same
way as in [Edit Properties] window.
For details, see “Editing Package Properties”
Copying a File (page 258).
To select the default package
You can copy category files between packages.
Press the [Default Package] button.
Note 8 In the [Target Package] group list, select a copy
Files cannot be copied to a locked package. destination file.
When multiple files are selected, select the first copy
1 Open the Home > File > Register > Effect Timeline >
destination file.
Copy menu (10104.13).
You can also press the [Select Destination] button and
enter a file number in the numeric keypad window.
2 Select a region.
The copy destination of the first file selected in the
The regions that can be selected vary depending on the [Source Package] group is the first file selected in the
category. [Target Package] group, and the subsequent files in the
[Target Package] group in the same relative positions
For details, see “To select a region” (page 265). as the selected files in the [Source Package] group
become copy destinations. The first file in the [Target
Note Package] group is shown in light blue, and the
Selection of a region is not required in the shotbox, subsequent copy destination files are shown in blue
macro, and macro attachment categories. gray.
4 Select a copy source package and press [OK]. 9 Press the [Copy] button.
To select the default package 10 Check the message, then press [OK].
Press the [Default Package] button.
The files are copied.
5 In the [Source Package] group list, select the target file
to copy.
267
1 Open the Home > File > Register > Effect Timeline >
Deleting a File Browse Files menu (10104.14).
The [Select Package] window appears. 5 In the [Package] group list, select the target file to
rename.
4 Select a package and press [OK].
To select and rename multiple files, place a check
To select the default package mark beside the target files to rename.
Press the [Default Package] button. To select and rename all files, place a check mark in
the Select All checkbox.
5 In the [Package] group list, select the target file to You can also press the [Select File(s)] button and enter
delete. a file number in the numeric keypad window.
To select and delete multiple files, place a check mark
Note
beside the target files to delete.
To select and delete all files, place a check mark in the Selection of a file is not required in the macro
Select All checkbox. attachment category as there is only one file.
You can also press the [Select File(s)] button and enter
a file number in the numeric keypad window. 6 Press the [Rename] button.
The [Rename] window appears.
Note
Selection of a file is not required in the macro 7 Press the input field and enter a file name (up to 8
attachment category as there is only one file. characters) using the keyboard.
7 Check the message, then press [OK]. The files are renamed.
Renaming a File
Note
268
5 Press [OK].
Locking File Loading To change the set password
Note
If a category with load lock enabled is selected as the
target for operation, the load lock enabled status is
retained.
To unlock loading
Select the target category to unlock and press the [Unlock]
button.
When a password is set, enter your password in the [Enter
Password] window and press [OK].
Note
If a category with load lock disabled is selected as the
target for operation, the load lock disabled status is
retained.
Setting a password
1 Open the Home > File > File Common > File Load
Lock menu (10106.11).
269
Content Management Chapter
Importing/exporting
20
Overview You can import still image/video/audio files from a
computer and save it in switcher content storage.
You can also import/export content archive files between
You can manage image and audio content used in frame switcher content storage and a computer.
memory, clip players, and SL keys.
Note
Content Content stored in switcher content storage may become
You can manage files imported from a computer and still unusable in the event of a content storage failure. Save a
image files/clip files (series of still images) created in backup of important content on a computer or on external
frame memory as content. media connected to a computer.
There are three types of content, as follows.
• Still image content
• Video content (including series of still images)
• Audio content
Content is saved in the switcher content storage.
Combined content
You can combine two still image content resources (such
as a video signal and key signal) or two video content
resources with the same duration to create a single content
resource. Content that combines two still image content
resources or two video content resources is called
combined content.
Linking video content with audio content allows you to
combine video and audio.
Folders
You can create folders for saving and managing content.
The created folder hierarchy can have up to five levels
below the root.
Default folder
A folder named “Default_Folder” is a default folder. It is
displayed directly beneath the root.
Default folders cannot be moved, deleted, or renamed.
Tags
You can add tags to content for identification.
By creating tags for each application or usage, content can
be managed efficiently.
270
Content Operations h g f e d cb a
Displaying Content
Open the Home > Content > Browse menu (10201.11).
A list of content is displayed.
List view (with properties)
h g f e d c b a
ji lk
m q n
e [Refresh] button
Updates the list view/thumbnail view by the criteria
configured using the [Filter] button or [Search] button.
i j k l m n o p q When the list view/thumbnail view needs to be updated
due to changes to content, for example, the [Refresh]
button icon is lit blue.
Thumbnail view
In thumbnail view, you can toggle between showing/ f [Search] button
hiding properties. Filters the list view/thumbnail view by character string
search criteria.
271
When character string search criteria is configured, the p Content size
[Search] button icon is lit blue.
q Content status
g [Filter] button The following status icons are displayed.
Filters the list view/thumbnail view by folder, tag, type,
and status selection criteria. Icon Status
When selection criteria is configured, the [Filter] button Locked
icon is lit blue.
k Content type
Loaded into SL key
Displays the following type icons.
Icon Type
Not saved in content storage
Video combined content
272
• Status icon
• Duration
• Size
• Added tags
• Folder path
• Memo
• Import date and time/creation date and time
• Modification date and time
• Still image/video information
- Horizontal resolution
- Vertical resolution
- Frame rate
- Scan method
- Codec Select criteria by placing check marks in the criteria setup
- Color space window and press [OK] to apply the settings.
- OETF Folder
- Color sampling method Under [Folder] in the criteria setup window, place a check
- File format mark for the folders to select.
• Audio information When a top-level folder is selected, lower level folders are
- Number of channels also selected and a check mark is placed in the checkboxes.
- Sampling rate When one or more lower level folders are selected, a blue
- Bit length square is displayed in the checkbox of the higher-level
- Codec folder.
- Duration Placing a check mark in [Root] selects all folders.
- File format
Tag
In [Tags] in the criteria setup window, set AND conditions
Sorting or OR conditions and place a check mark for tags to select.
You can press a display item title to sort the display. [AND] radio button: Displays content which has all the
Sorting switches between ascending and descending order selected tags.
each time you press a title. [OR] radio button: Displays content which has one or
When sorted in ascending or descending order, [v] more of the selected tags.
(ascending) or [V] (descending) is displayed on the right
side of the title. Type
Type: Sort by content type Under [Type] in the criteria setup window, place a check
In ascending order, the content is sorted in order of mark for the types to select.
video combined content > video content > still image To select all types, place a check mark in [All Types].
combined content > still image content > audio
Status
content.
Under [Status] in the criteria setup window, place a check
In descending order, the sort order is reversed.
mark for the status to select.
Name: Sort by content name
To select all status, place a check mark in [All Status].
Duration: Sort by content duration
Tags: Sort by first tag name
Imported: Sort by import date and time/creation date and Searching
time Press the [Search] button and enter a character string to
Size: Sort by size search for in the search window.
Only content containing the entered character string is
Filtering by criteria displayed.
Press the [Filter] button and set the filter criteria in the
criteria setup window.
Only content matching the selected folder, tag, type, or
status is displayed.
273
Press the input field in the search window and enter a To select and copy multiple content, place a check
character string to search for using the keyboard. mark beside the target content to copy.
Press [OK] to apply the character string to search for. To select and copy all displayed content, place a check
The following items can be searched. mark in the Select All checkbox.
• Content name
• Tags 3 Press the [Copy] button.
• Memo
4 Check the message, then press [OK].
Specifying search criteria
You can specify an AND condition or OR condition to The [Copy] window appears.
search for multiple character strings.
5 Select a copy destination folder.
Note
To create a folder
An AND condition search only matches within each item Press the [New Folder] button to display the [New
(content name, tag, memo). You cannot search across Folder] window.
multiple items. Press the input field and enter a folder name (up to 32
characters) using the keyboard, then press [OK].
Input example Search criteria A new folder is created within the selected folder.
aaa bbb Includes both “aaa” and “bbb”
character strings. Note
(Entries separated by a space form an
AND condition.) A folder cannot be created when a folder at the 5th
aaa AND bbb Includes both “aaa” and “bbb” level of the hierarchy is selected.
character strings.
aaa OR bbb Includes “aaa” or “bbb” character 6 Press [OK].
string.
The content is copied to the selected folder.
aaa OR bbb AND Includes both “bbb” and “ccc”
ccc character strings, or includes “aaa”.
If content with the same name exists in a folder, a copy
(AND condition has precedence.) count (underscore and copy number) is added to the
end of the content name.
(aaa OR bbb) AND Includes “aaa” or “bbb” character
ccc string and “ccc” character string.
(Parentheses have precedence.) Note
“AND” Includes the “AND” character string. Tags and memos added to content are also copied.
(To search for the “AND” or “OR”
character string, enclose the word in
double quotations.)
Search history
Moving Content
The search history is displayed below the input field. You
can select a character string to search for from the history. Notes
1 Open the Home > Content > Browse menu (10201.11). 4 Check the message, then press [OK].
The [Move] window appears.
2 Select the target content to copy.
274
5 Select a destination folder. Note
To create a folder If locked content is selected as the target for operation,
Press the [New Folder] button to display the [New the locked status is retained.
Folder] window.
Press the input field and enter a folder name (up to 32 To release the lock
characters) using the keyboard, then press [OK]. Select the target content to unlock and press the [Unlock]
A new folder is created within the selected folder. button.
Note Note
A folder cannot be created when a folder at the 5th If unlocked content is selected as the target for operation,
level of the hierarchy is selected. the unlocked status is retained.
6 Press [OK].
The content is moved to the selected folder. Editing Content Properties
If content with the same name exists in a folder, a copy
count (underscore and copy number) is added to the Notes
end of the content name.
• The properties of locked content cannot be edited.
• The properties of loaded content cannot be edited.
Deleting Content 1 Open the Home > Content > Browse menu (10201.11).
• Locked content cannot be deleted. To select and edit multiple content, place a check mark
• Loaded content cannot be deleted. beside the target content to edit.
To select and edit all displayed content, place a check
1 Open the Home > Content > Browse menu (10201.11). mark in the Select All checkbox.
2 Select the target content to delete. 3 Press the [Edit Properties] button.
To select and delete multiple content, place a check The [Edit Properties] window appears.
mark beside the target content to delete.
To select and delete all displayed content, place a 4 Press the [Name] button and enter a content name (up
check mark in the Select All checkbox. to 64 characters) using the keyboard.
4 Check the message, then press [OK]. When multiple content is selected, the content names
cannot be edited.
275
6 Press the [Memo] button and enter a memo (up to 255
characters) using the keyboard.
Combining Content
Note
When multiple content is selected, the memo of all Combining images
content will have the same description. You can combine video and video content resources or still
image and still image content resources.
7 Press [OK]. The combined content is saved as new combined content.
The original content is not deleted.
Notes
• Video content with different durations cannot be
combined.
• Content with different image attributes, such as
resolution and frame rate, cannot be combined.
Note
Combined content and audio content are not
displayed.
276
• The content name is the name of content 1 with “_CMB” • The content name is the name of the video content with
appended to the end. “_LNK” appended to the end.
If the name exceeds 64 characters, some characters at the If the name exceeds 64 characters, some characters at the
end of the content 1 name will be deleted. end of the video content name will be deleted.
• If content with the same name exists, a copy count • If content with the same name exists, a copy count
(underscore and copy number) is added to the end. (underscore and copy number) is added to the end.
• The tag properties of content 1 and content 2 are all • The tag properties of the video content and audio content
added. are all added.
• The memo property of content 1 is added. • The memo property of the video content is added.
• The duration is the same as the video content.
Linking an image and audio
You can link audio content to video content or video Separating combined/linked content
combined content. Separated content is saved as new content. The original
The linked content is saved as new content. The original content is not deleted.
content is not deleted.
1 Open the Home > Content > Combine/Separate >
1 Open the Home > Content > Combine/Separate > Link Separate menu (10201.23).
Audio menu (10201.22).
A list of content is shown on the right.
Selection buttons for video content and audio content For details about the list display, see “Displaying
are shown on the left. Content” (page 271).
A list of content is shown on the right.
For details about the list display, see “Displaying Note
Content” (page 271).
Only content that can be separated is displayed.
Note
2 Select content from the list displayed on the right.
Still image content is not displayed.
The thumbnail and information for the selected
2 Press the [Video] button on the left. content is displayed on the left.
3 Select video content from the list displayed on the 3 Press the [Separate Now] button.
right.
4 Check the message, then press [OK].
The thumbnail and information for the selected
content is displayed on the [Video] button. The content is separated and saved in the same folder.
Name and properties of separated content
4 Press the [Audio] button on the left. The name and properties of separated content are set
according to the following rules.
5 Select audio content from the list displayed on the • For combined content, the content name is the original
right. name with “_V1” (content 1) and “_V2” (content 2)
The thumbnail (audio type icon) and information for appended to the end.
the selected content is displayed on the [Audio] button. For linked content, the content name is the original name
with “_A” (audio content), “_V1” (video content/video
6 Press the [Link Now] button. combined content 1), and “_V2” (video combined
content 2) appended to the end.
To release the content selection If the name exceeds 64 characters, some characters at the
Press the [Clear] button. end of the combined/linked content name will be
deleted.
7 Check the message, then press [OK]. • If content with the same name exists, a copy count
(underscore and copy number) is added to the end.
The audio content is linked to the video content, and • The tag properties of the combined/linked content are
the linked content is saved in the video content folder. added.
Name and properties of linked content • The memo property of the combined/linked content is
The name and properties of linked content are set added.
according to the following rules.
277
Place a check mark for each tag to add.
Importing/Exporting To create a tag
Press the [New Tag] button to display the [New Tag]
Content window.
Press the input field and enter a tag name (up to 24
characters) using the keyboard, then press [OK].
Importing Content
4 Press the input field in [Memo] and enter a memo (up
You can import files from a computer and save it in to 255 characters) using the keyboard.
content storage as content.
5 Press [OK].
Creating an import list
Importing
1 Open the Home > Content > Import/Export > Import The files in the import list can be imported.
from Files menu (10201.31).
An import list and the properties to add to imported
1 Open the Home > Content > Import/Export > Import
from Files menu (10201.31).
content are displayed.
A computer file selection dialog appears. 3 Check the message, then press [OK].
The imported files are saved as content in content
3 Select a file to import. storage.
The selected file is added to the import list. A “ ” icon is displayed on the left for files that failed
to import.
Import list
The following information is displayed in the import list. Note
• File name
• File modification date and time The name of imported content is set according to the
• File size following rules.
To delete a file from the import list, press the [×] button on • The content name is the file name with the file name
the right of the file. extension removed.
• The content name can be up to 64 characters. The
To set the properties to add to imported content 65th and subsequent characters are deleted.
You can set folders for saving content and add tags and a • If content with the same name exists, a copy count
memo to content. (underscore and copy number) is added to the end.
• Characters that cannot be used are replaced with
1 Press the [Set Import Properties] button. underscores.
For details, see “Invalid characters for names”
The [Set Import Properties] window appears.
(page 43).
2 Select a save destination folder in [Select Destination Importing a series of still images
Folder]. When multiple files with names in “character_string +
number (or character_string + # + number)” format are
To create a folder
imported, the files with the same “character_string”
Press the [New Folder] button to display the [New
portion and consecutive “number” portions are imported
Folder] window.
as video content (series of still images). The
Press the input field and enter a folder name (up to 32
“character_string” portion becomes the content name.
characters) using the keyboard, then press [OK].
Example:
A new folder is created within the selected folder.
Importing TARGA files
278
File name before Content name after importing Reduce the size of the archive file, for example by
importing (series of still images) reducing the number of content resources, and then
MON101.tga MON execute the export again.
MON102.tga
MON103.tga 1 Open the Home > Content > Import/Export > Export
as Archive menu (10201.33).
Note
A list of content is displayed.
Files in the following file formats can be imported as a For details about the list display, see “Displaying
series of still images. Content” (page 271).
• TIFF file
• BMP file To edit properties
• TARGA file Press the [Edit Properties] button.
• PNG file For details about editing properties, see “Editing
Importing audio Content Properties” (page 275).
Audio with a sampling frequency of 32 kHz, 44.1 kHz, or
48 kHz can be imported. 2 Select content to export.
To select and export multiple content, place a check
mark beside the target content to export.
Importing a Content Archive File To select and export all displayed content, place a
check mark in the Select All checkbox.
Note
3 Press the [Export Now] button.
Only archive files that have been exported using the Home
> Content > Import/Export > Export as Archive menu 4 Check the message, then press [OK].
(10201.33) can be imported.
An archive file for the selected content is exported.
1 Open the Home > Content > Import/Export > Import The file name extension for an archive file is “.scz”.
from Archive menu (10201.32).
Note
279
Note
Editing a Folder A folder cannot be created when a folder at the 5th
level of the hierarchy is selected.
Creating a folder 6 Press [OK].
1 Open the Home > Content > Folder/Tag > Folder The folder is moved into the selected folder.
menu (10201.41). If a folder with the same name exists, a copy count
(underscore and copy number) is added to the end of
2 Select a location (high-level folder) in which to create the folder name.
a folder.
Note
Note
A folder cannot be moved if it would result in a folder
A folder cannot be created when a folder at the 5th hierarchy exceeding five levels.
level of the hierarchy is selected.
Deleting a folder
3 Press the [New] button.
Only empty folders can be deleted.
The [New Folder] window appears.
Note
4 Press the input field and enter a folder name (up to 32
characters) using the keyboard. Default folders cannot be deleted.
5 Press [OK]. 1 Open the Home > Content > Folder/Tag > Folder
menu (10201.41).
A new folder is created within the selected folder.
2 Select the target folder to delete.
Moving a folder
3 Press the [Delete] button.
Notes
4 Check the message, then press [OK].
• Default folders cannot be moved.
• A folder cannot be moved into a lower-level folder Renaming a folder
within it.
1 Open the Home > Content > Folder/Tag > Folder Note
menu (10201.41). Default folders cannot be renamed.
2 Select the target folder to move. 1 Open the Home > Content > Folder/Tag > Folder
menu (10201.41).
3 Press the [Move] button.
2 Select the target folder to rename.
4 Check the message, then press [OK].
The [Move] window appears.
3 Press the [Rename] button.
The [Rename Folder] window appears.
5 Select a location (high-level folder) in which to move
a folder. 4 Press the input field and enter a folder name (up to 32
characters) using the keyboard.
To create a folder
Press the [New Folder] button to display the [New
Folder] window.
5 Press [OK].
Press the input field and enter a folder name (up to 32
characters) using the keyboard, then press [OK].
A new folder is created within the selected folder.
280
2 Select the target tag to rename.
Editing a Tag Note
It is not possible to select and rename multiple tags.
You can create, delete, and rename tags to add to content
or packages. 3 Press the [Rename] button.
For details about packages, see “Chapter 19 File The [Rename Tag] window appears.
Management” (page 255).
4 Press the input field and enter a tag name (up to 24
characters) using the keyboard.
Creating a tag
1 Open the Home > Content > Folder/Tag > Tag menu
5 Press [OK].
(10201.42).
Note
2 Press the [New] button. In addition to the tag definition, tags already added to
content/packages are also renamed.
The [New Tag] window appears.
4 Press [OK].
Deleting a tag
Notes
1 Open the Home > Content > Folder/Tag > Tag menu
(10201.42).
Note
In addition to the tag definition, tags already added to
content/packages are also deleted.
Renaming a tag
1 Open the Home > Content > Folder/Tag > Tag menu
(10201.42).
281
System Setup Chapter
282
Saving user setup
Setting the Startup Mode
User configured setup data and initial status data are saved
You can set the startup mode for each of the switcher, in non-volatile memory.
frame memory/clip player/SL key, and control panel.
For details about saved data, see “Data Saved by [Setup
Note
Define] and [Initial Status Define]” (page 386).
DMEs are included in the startup mode of the switcher. To save setup data
However, DMEs do not support resume mode. When the
switcher is set to resume mode, DMEs start in custom 1 Open the Home > Setup > System > Start Up menu
mode. (19101.11).
1 Open the Home > Setup > System > Start Up menu 2 In the [Setup Define] group, select the target to save.
(19101.11).
Switcher: Switcher
2 Select the target to set. Panel: Control panel
Select a switcher, frame memory/clip player/SL key, 3 Check the message, then press [OK].
or control panel.
To save initial status data
3 Press the [Start Up Mode] button and select a startup
mode from the pull-down list. 1 Open the Home > Setup > System > Start Up menu
(19101.11).
Resume: Resume mode
Custom: Custom mode 2 In the [Initial Status Define] group, select the target to
When [Resume] mode is selected, steps 4 and 5 are not save.
required.
Switcher/Content: Switcher and frame memory/clip
player/SL key
Note
Panel: Control panel
You can set the frame memory/clip player/SL key
startup mode only when the switcher is set to resume 3 Check the message, then press [OK].
mode.
When the switcher is set to custom mode, frame
memory/clip player/SL keys are also set to custom Applying Initial Status File Settings
mode (fixed).
You can recall an initial status file to apply the setup status
4 Press the [Setup] button and select a startup mode from saved in the file, regardless of the startup mode settings.
the pull-down list.
User: User setup Notes
Factory: Factory default setup • When the [Load and Recall Initial Status] switch is
enabled and an initial status file is saved, the setup status
Note at that point in time is saved.
The setup mode cannot be set for frame memory/clip For details about initial status files, see “Chapter 19
player/SL keys. File Management” (page 255).
• Control panel and DME cannot be set.
5 Press the [Initial Status] button and select an initial • You can set frame memory/clip player/SL key only
status mode from the pull-down list. when the switcher setting is enabled.
User: User setup 1 Open the Home > Setup > System > Start Up menu
Factory: Factory default setup (19101.11).
When the switcher is set to [Factory] in custom mode, Select switcher or frame memory/clip player/SL key.
the initial status mode for frame memory/clip player/
SL keys is also set to [Factory] (fixed).
283
3 Enable/disable the function using the [Load and Recall 1 Open the Home > Setup > System > Start Up menu
Initial Status] switch. (19101.11).
On: Enabled. 2 Press the [Sys Setup All Clear] button.
Off: Disabled.
3 Check the message, then press [OK].
1 Open the Home > Setup > System > Start Up menu
(19101.11).
Note
The following system setup menus are not affected by a
system setup all clear.
They are the target of a switcher reset/all clear.
• Home > Setup > System > Input menu (19101.31 to
19101.35)
• Home > Setup > System > Output menu (19101.41 to
19101.46)
284
• Home > Utility
Setting the System •
•
Home > Setup > System > Input
Home > Setup > System > Output
Configuration •
•
Home > Setup > Xpt Assign > Main, V/K Pair Assign
Home > Setup > Xpt Assign > Src Name/Src Color >
Edit Src Name/Color
• Home > Setup > Xpt Assign > Xpt Delay
Setting Dual Simul Mode • Home > Setup > Switcher > Config > PGM Config
• Home > Setup > Switcher > Config > K-PVW Config
When dual simul mode is enabled, two switchers can be • Home > Setup > Switcher > Config > DSK Bkgd Assign
controlled simultaneously from a single control panel. • Home > Setup > Switcher > Config > DME Config
• Home > Setup > Switcher > Config > User Region
Notes Config
• Home > Setup > Switcher > Multi Viewer
• The first switcher is a switcher in the same switcher • Home > Setup > Switcher > DME Interface
system as the control panel. For the second switcher, • Home > Setup > Switcher > Custom
specify a switcher from another switcher system. • Home > Setup > Link > Internal Bus Link
• The status of the first switcher is displayed on the control • Home > Setup > Link > M/E Link
panel and in the menu. • Home > Setup > Link > Key Transition Link > Link in
Multi M/Es
1 Open the Home > Setup > System > Format/Config > • Home > Setup > Link > Aux Bus CCR Link
Config menu (19101.21).
285
Move to video playback stop point License (option) is required. To use the SL key function,
Move to end of video content the XZS-G1620 SL Key License (option) is required.
[Variable Speed] button • The DME function is not supported in version 1.0.
[Set Loop Playback] button Setting a GPU enables the SL key function.
1 Open the Home > Setup > System > Format/Config >
Setting M/E Split GPU Config menu (19101.25).
You can split an M/E hardware block (physical M/E block) 2 In the [GPU Config] group, select a function to enable.
of the switcher for use as two sub blocks.
DME: Enable DME.
You can assign a logical M/E to each sub block.
SL Key: Enable SL key.
For details about assigning a logical M/E, see “Assigning
a Logical M/E” (page 306).
3 Press the [Apply] button.
To return to the previous setting
Notes Press the [Clear] button.
• Enabling M/E split will disable multi program 2 mode. 4 Check the message, then press [OK].
• When M/E split is enabled, the Out5 to Out8 outputs
cannot be used. The switcher system reboots.
• When M/E split is enabled, the keys that can be used in
a single physical switcher block can be assigned to the
two sub blocks. You can set the number of keys to Setting DME Channel Enhanced
assign.
For details about setting keys, see “Setting Sub Block Function Mode
keys” (page 306).
1 Open the Home > Setup > System > Format/Config >
1 Open the Home > Setup > System > Format/Config > GPU Config menu (19101.25).
M/E Split menu (19101.24).
2 Set enhanced function mode.
2 Select the target physical M/E block to set.
To set DME channel 1
In the [DME Channel 1] group, enable/disable
3 Set the [M/E Split] switch to the on state.
enhanced function mode.
To disable M/E split, set the [M/E Split] switch to the Enhanced: Enable enhanced function mode.
off state. Normal: Disable enhanced function mode.
To set DME channel 2
4 Press the [Apply] button.
In the [DME Channel 2] group, enable/disable
To return to the previous setting enhanced function mode.
Press the [Clear] button. Enhanced: Enable enhanced function mode.
Normal: Disable enhanced function mode.
5 Check the message, then press [OK].
3 Press the [Apply] button.
The switcher system reboots.
To return to the previous setting
Press the [Clear] button.
Setting a GPU 4 Check the message, then press [OK].
The DME and SL key functions use a GPU. The switcher system reboots.
When the system signal format is 2160P, either the DME
function or SL key function can be enabled.
Notes
• To use the DME and SL key functions, the XKS-G1600
GPU Pack (option) must be installed.
To use the DME function, the XZS-G1610 3D DME
286
Internal: Internal lock mode
Setting the Signal Format Use switcher internal signal as the reference
signal.
You can select the system signal format and the field Cannot be set when the reference signal is in internal lock
frequency/frame frequency. mode.
The combinations of signal format and frequency that can
be set are as follows. 1 Open the Home > Setup > System > Format/Config >
Format menu (19101.22).
Signal format Frequency
4K 2160P 2SI 59.94 2 In the [Ref Input Format] group, select a reference
50 signal.
HD 1080P 59.94
50 Tri Sync: HD tri-level sync
BB: Black burst or sync
1080i 59.94
50
Setting the output reference signal
Note
To use 4K formats, the XZS-G1500 4K Upgrade License
1 Open the Home > Setup > System > Format/Config >
Format menu (19101.22).
(option) is required.
1 Open the Home > Setup > System > Format/Config >
2 In the [Ref Output Format] group, select a reference
signal.
Format menu (19101.22).
Tri Sync: HD tri-level sync
2 In the [Signal Format] group, select a signal format. BB: Black burst or sync
5 Check the message, then press [OK]. 2 In the [Switch Timing] group, select the switch timing.
The switcher system reboots. Any: Not specified
Field1: Field 1
Field2: Field 2
Setting the Reference Signal
You can set the input/output reference signal to HD tri- Setting the Reference Phase
level sync or black burst.
1 Open the Home > Setup > System > Format/Config >
Setting the reference signal lock mode Format menu (19101.22).
1 Open the Home > Setup > System > Format/Config > 2 Press the [System Phase] button and enter a reference
Format menu (19101.22). phase (microseconds) in the numeric keypad window.
287
Display Referred: Perform SDR to HDR, HDR to
Setting the Dynamic Range SDR, or HDR to HDR conversion matching the
visual appearance of the image on a display.
Setting the OETF and color space
You can select the OETF (Opto-Electronic Transfer Setting HDR
Function) and color space. You can configure HDR when the OETF is set to [HLG],
The combinations of signal formats and OETF/color space [PQ], [S-Log3 (HDR)], or [S-Log3 (Live HDR)].
that can be selected are as follows. Highlight Creation: Highlight creation function for when
converting from SDR to HDR
Signal format OETF Color space Highlight creation is a function that makes high-
2160P SDR BT.709, BT.2020 luminance areas brighter according to a knee
HLG, PQ, S-Log3 BT.2020 characteristic during conversion.
(HDR), S-Log3 (Live Specify the knee point position and slope of the curve.
HDR) HDR Contrast: HDR contrast level corresponding to SDR
1080P SDR BT.709 100% level (display only)
HLG, PQ, S-Log3 BT.2020 HDR Gain (dB): Gain when converting from SDR to HDR
(HDR), S-Log3 (Live
HDR) Note
1080i SDR BT.709
When the conversion mode is [Display Referred], the
highlight creation function cannot be set.
Note
Changing the OETF/color space settings may momentarily 1 Open the Home > Setup > System > Format/Config >
distort the image. HDR/SDR Format menu (19101.23).
1 Open the Home > Setup > System > Format/Config > 2 Enable/disable the highlight creation function using
HDR/SDR Format menu (19101.23). the [Highlight Creation] button.
On: Enable the highlight creation function.
2 In the [OETF] group, select an OETF.
Off: Disable the highlight creation function.
SDR: SDR (Standard Dynamic Range) When disabled, proceed to step 5.
HLG: HLG (Hybrid Log Gamma)
PQ: PQ (Perceptual Quantization) 3 Press the [Point (Abs.)] button and select a knee point
S-Log3 (HDR): S-Log3 position for the curve from the pull-down list.
S-Log3 (Live HDR): Display with system gamma
added to S-Log3 4 Press the [Slope (Abs.)] button and select a slope for
the curve from the pull-down list.
3 In the [Color] group, select a color space.
5 Press the [HDR Gain (dB)] button and enter a gain
BT.709: BT.709 color space value in the numeric keypad window.
BT.2020: BT.2020 color space
To set the HDR Look function
You can set the visual appearance of the HDR image on a
Setting the input signal conversion mode display.
1 Open the Home > Setup > System > Format/Config > 1 Open the Home > Setup > System > Format/Config >
HDR/SDR Format menu (19101.23). HDR/SDR Format menu (19101.23).
2 In the [Conversion Mode] group, select a conversion 2 Press the [HDR Look] button and select a type of look
mode. from the pull-down list.
AIR Matching On: Enable the AIR Matching Live: Vivid images with high contrast and color
(Artistic Intent Render Matching) function. This saturation.
performs conversion such that the visual Mild: Generally more mild images than that produced
appearance on the output signal display matches using [Live].
that of the input signal display. Natural: Images with reduced sensitivity, but which is
AIR Matching Off: Disable the AIR Matching less affected by noise.
function.
288
Note
Off: Disable the knee function.
When disabled, proceed to step 5.
When the OETF is set to [PQ], [S-Log3 (HDR)], or
[S-Log3 (Live HDR)], [Natural] cannot be set. 3 Press the [Point (Abs.)] button and select a knee point
position for the curve from the pull-down list.
To set the HDR black compression function
You can enable the black compression function and adjust 4 Press the [Slope (Abs.)] button and select a slope for
the HDR black level so that it is the same as for SDR. the curve from the pull-down list.
1 Open the Home > Setup > System > Format/Config > 5 Enable/disable the white clip function using the
HDR/SDR Format menu (19101.23). [White Clip] button.
2 Enable/disable the black compression function using On: Enable the white clip function.
the [HDR Black Comp.] button. Press the button on the right of the [White Clip]
button and enter a video signal level in the numeric
On: Enable the black compression function. keypad window.
Off: Disable the black compression function. Off: Disable the white clip function.
To set the HDR black level
6 Press the [SDR Gain (dB)] button and enter a gain in
1 Open the Home > Setup > System > Format/Config > the numeric keypad window.
HDR/SDR Format menu (19101.23).
7 In the [Gamma (Table)] group, select a type of gamma
2 Press the [Master Black (Abs.)] button in the [Black curve.
Level] group and enter a master black value in the Standard: Use standard.
numeric keypad window. Press the button on the right of the [Standard]
button and enter a table number (1 to 7) in the
3 Press the [HDR Black Offset] button in the [Black numeric keypad window.
Level] group and enter an HDR black offset in the Press the [Step] button and enter a gamma strength
numeric keypad window. (step) in the numeric keypad window. The effect
changes in increments of 0.05.
Setting SDR Press the [Level] button and enter a gamma
You can configure SDR when the OETF is set to [SDR]. strength (level) in the numeric keypad window.
Knee: Knee function when converting from HDR to SDR Hyper: Use hypergamma.
The knee is a function that compresses high luminance Press the button on the right of the [Hyper] button
areas. and enter a table number (1 to 4) in the numeric
Specify the knee point position and slope of the curve. keypad window.
White Clip: White clip function when converting from
HDR to SDR
Specify the level of the video signal.
HDR Contrast: SDR contrast level corresponding to HDR
100% level (display only)
SDR Gain (dB): Gain when converting from HDR to SDR
Gamma (Table): Type of gamma curve
Select from standard gamma and hypergamma.
Note
When the conversion mode is [Display Referred], the type
of gamma curve cannot be set.
1 Open the Home > Setup > System > Format/Config >
HDR/SDR Format menu (19101.23).
289
Selecting Inputs Configurable with a
Setting the Input Signal Color Corrector/HDR Converter
You can set inputs that can be configured with a color
This section describes how to set the switcher input signal.
corrector/HDR converter.
The number of inputs will vary depending on the system
signal format.
2160P format: Notes
Inputs: Max. 24 • Configurable only when the system signal format is
Inputs configurable with color corrector/HDR 2160P.
converter: Max. 6 • Up to six inputs can be configured with a color corrector/
Inputs configurable with format converter: 12 (odd- HDR converter.
numbered inputs only)
1080P, 1080i formats: 1 Open the Home > Setup > System > Input > Input
Inputs: Max. 44 Adjust menu (19101.31).
Inputs configurable with format converter: 24 (inputs
1 to 24 only) 2 Select the target input to set.
When multiple inputs are selected, consecutively 4 Press the button on the right of the [Frame Delay]
numbered source names are set. switch and enter a delay value in the numeric keypad
For details, see “Name settings when multiple items window.
are selected” (page 43).
The delay value that can be set will vary depending on
the signal format of the input signal.
2160P, 1080P, 720P: 1 to 11 frames
1080i, 576i, 480i: 1 to 4 frames
290
1 Open the Home > Setup > System > Input > FC Format
Setting a Frame Synchronizer menu (19101.32).
When a frame synchronizer is enabled, unsynchronized
input signals are synchronized.
2 Select the target input to set.
To select and set multiple inputs, place a check mark
1 Open the Home > Setup > System > Input > Input beside the target inputs to set.
Adjust menu (19101.31). To select and set all inputs, place a check mark in the
Select All checkbox.
2 Select the target input to set.
To select and set multiple inputs, place a check mark
3 Press the [FC Format] button and select an input signal
format from the pull-down list.
beside the target inputs to set.
To select and set all inputs, place a check mark in the
Select All checkbox. Adjusting the conversion method
The conversion method adjustment items and the target
3 Set the [Frame Synchronizer] switch to the on state. conversion formats are given below.
To disable a frame synchronizer, set the [Frame Adjustment item Conversion format
Synchronizer] switch to the off state.
Up-converter • 480i t 1080i
conversion mode • 576i t 1080i
• 1080i t 2160P
Setting a Format Converter I/P converter conversion • 1080i t 1080P
mode
When the system signal format is 2160P, you can use a
Up-converter aspect • 480i t 1080i
format converter on odd-numbered inputs. ratio • 576i t 1080i
When the system signal format is 1080P or 1080i, you can
use a format converter on inputs 1 to 24.
1 Open the Home > Setup > System > Input > FC Adjust
menu (19101.33).
Setting the conversion format
You can set the signal format of an input signal to convert 2 Select the target input to set.
by the format converter. To select and set multiple inputs, place a check mark
beside the target inputs to set.
Note To select and set all inputs, place a check mark in the
Select All checkbox.
Field frequency and frame frequency conversion is not
supported.
3 Adjust the conversion method.
The signal formats that can be converted are given below. To set the up-converter conversion mode
Press the [Conversion] button and select a conversion
System signal format Signal format of input
(frequency) signal mode from the pull-down list.
Frame: Conversion in frame units
2160P 2SI 1080i
Field: Conversion in field units
(59.94, 50) 1080P
2160P 2SI 3G a) Adaptive: Detects motion in the signal, and automatically
2160P 2SI 12G switches mode between conversion in frame units and
1080P 720P field units.
(59.94, 50) 1080i When [Adaptive] is selected, press the [Motion] button
1080P and enter a detection sensitivity (1 to 4) in the numeric
1080i 480i keypad window.
(59.94) 720P 1: Highest proportion converted from frames (still image
1080i priority mode).
1080i 576i 2: Higher proportion converted from frames.
(50) 720P 3: Higher proportion converted from fields.
1080i 4: Highest proportion converted from fields (motion
a) Only the first number input in each group of four inputs can be set. The
priority mode)
settings of the inputs in each group are linked and change accordingly.
291
To set the I/P converter conversion mode
Press the [Conversion] button and select a conversion No. Parameter Adjustment
mode from the pull-down list. 1 LB Position Image position
Frame: Conversion in frame units
Field: Conversion in field units To return the conversion method settings to the
Adaptive Y: Detects motion in the luminance signal, and defaults
automatically switches mode between conversion in Press the [Default] button.
frame units and field units.
Adaptive Y/C: Detects motion in the luminance signal
and chrominance signal, and automatically switches Setting a Color Corrector
mode between conversion in frame units and field
units. You can set the following color corrector functions for
When [Adaptive Y] or [Adaptive Y/C] is selected, press inputs that have color corrector/HDR converter enabled.
the [Motion] button and enter a detection sensitivity (1 to • Primary color correction
4) in the numeric keypad window. • RGB clip
1: Highest proportion converted from frames (still image
priority mode). For details about inputs that can be configured with a
2: Higher proportion converted from frames. color corrector/HDR converter, see “Selecting Inputs
3: Higher proportion converted from fields. Configurable with a Color Corrector/HDR Converter”
4: Highest proportion converted from fields (motion (page 290).
priority mode)
To set the up-converter aspect ratio Note
Press the [Aspect] button and select an aspect ratio from When the system signal format is 1080P or 1080i, a color
the pull-down list. corrector cannot be used.
Edge Crop: Add black bars on the left and right sides of a
4:3 image to convert it to a 16:9 image. 1 Open the Home > Setup > System > Input > Input CCR
Letter Box: Crop the top and bottom of a 4:3 image to menu (19101.34).
convert it to a 16:9 image.
Squeeze: Stretch a 4:3 image horizontally to covert it to a 2 Select the target input to set.
16:9 image.
292
Setting an HDR Converter Note
When multiple inputs are selected, the [Follow System
You can set the input signal OETF, color space, and HDR Settings] switch settings do not change in unison.
converter for inputs that have color corrector/HDR
converter enabled.
[HDR Converter] window > [Config] tab
For details about each HDR conversion item, see “Setting Sets the HDR conversion mode.
HDR” (page 288).
1 In the [Conversion Mode] group, select a conversion
For details about inputs that can be configured with a mode.
color corrector/HDR converter, see “Selecting Inputs
Configurable with a Color Corrector/HDR Converter” Select [AIR Matching On], [AIR Matching Off], or
(page 290). [Display Referred].
Notes
2 Press the [HDR Look] button and select a type of look
from the pull-down list.
• To use the HDR converter function, the XZS-G1750
HDR Converter License (option) is required. Select [Live], [Mild], or [Natural].
• When the system signal format is 1080P or 1080i, an
HDR converter cannot be used. Notes
• When the input signal OETF is set to [PQ], [S-Log3
1 Open the Home > Setup > System > Input > HDR (HDR)], or [S-Log3 (Live HDR)], [Natural] cannot
Converter menu (19101.35). be selected.
The system OETF, color space, and HDR settings are • This cannot be set when the input signal OETF is set
displayed in [System Settings]. to [SDR].
• This cannot be set when the [Look Conversion]
2 Select the target input to set. button is set to the on state on the [Additional Paint]
tab.
To select and set multiple inputs, place a check mark
beside the target inputs to set. 3 Enable/disable the black compression function using
To select and set all inputs, place a check mark in the the [HDR Black Comp.] button.
Select All checkbox.
Note
3 Press the [Input Signal OETF] button and select an
OETF from the pull-down list. This cannot be set when the [Look Conversion] button
is set to the on state on the [Additional Paint] tab.
Select [SDR], [HLG], [PQ], [S-Log3 (HDR)], or
[S-Log3 (Live HDR)]. 4 In the [Black Level] group, set the black level.
4 Press the [Color] button and select a color space from For a Sony system camera input signal
the pull-down list. Press the [Sony System Camera] button.
Press the [Master Black (Abs.)] button and enter a
Select [BT.709] or [BT.2020]. master black value in the numeric keypad window.
Press the [HDR Black Offset] button and enter an
5 Enable/disable the system settings using the [Follow HDR black offset in the numeric keypad window.
System Settings] switch.
For a non-Sony system camera input signal
On: Enable system settings. Apply the system settings Press the [Others] button.
to the input signal. Press the [Master Black (HDR)] button and enter an
Off: Disable system settings. Apply different settings HDR black level in the numeric keypad window.
than the system settings to the input signal. Press the [Master Black (SDR)] button and enter an
If the system settings are disabled, press the [Adjust SDR black level in the numeric keypad window.
Details] button and configure the HDR conversion
settings in the [HDR Converter] window. Notes
• When the system OETF and input signal OETF are
set to [SDR], [Black Level (HDR)] cannot be set.
293
• When the system OETF and input signal OETF are Note
set to [HLG], [PQ], [S-Log3 (HDR)], or [S-Log3
(Live HDR)], [Black Level (HDR)] cannot be set. This cannot be set when the input signal conversion
mode is set to [Display Referred].
[HDR Converter] window > [Conversion] 4 Enable/disable the black clip function using the [HDR
tab Black Clip] button.
Sets the mode for conversion from HDR to HDR, SDR to
HDR, or HDR to SDR. On: Enable the black clip function.
Off: Disable the black clip function.
Note
Note
This cannot be set when the system OETF and input signal
OETF are set to [SDR]. This cannot be set when the system OETF is set to [S-
Log3 (HDR)] or [S-Log3 (Live HDR)].
When converting from HDR to HDR
Enable/disable the black clip function using the [HDR When converting from HDR to SDR
Black Clip] button.
On: Enable the black clip function. 1 Enable/disable the knee function using the [Knee]
Off: Disable the black clip function. button.
On: Enable the knee function.
Note Press the [Point (Abs.)] button and select a knee
point position for the curve from the pull-down
This cannot be set when the system OETF is set to [S-Log3
list.
(HDR)] or [S-Log3 (Live HDR)].
Press the [Slope (Abs.)] button and select a slope
When converting from SDR to HDR for the curve from the pull-down list.
Off: Disable the knee function.
1 Enable/disable the highlight creation function using
the [Highlight Creation] button. 2 Enable/disable the white clip function using the
[White Clip] button.
On: Enable the highlight creation function.
Press the [Point (Abs.)] button and select a knee On: Enable the white clip function.
point position for the curve from the pull-down Press the button on the right of the [White Clip]
list. button and enter a video signal level in the numeric
Press the [Slope (Abs.)] button and select a slope keypad window.
for the curve from the pull-down list. Off: Disable the white clip function.
Off: Disable the highlight creation function.
3 Press the [SDR Gain (dB)] button and enter a gain for
Note
converting in the numeric keypad window.
This cannot be set when the input signal conversion 4 In the [Gamma (Table)] group, select a type of gamma
mode is set to [Display Referred]. curve.
2 Press the [HDR Gain (dB)] button and enter a gain for Standard: Use standard.
converting in the numeric keypad window. Press the button on the right of the [Standard]
button and enter a table number (1 to 7) in the
3 In the [De-Gamma] group, set the type of gamma numeric keypad window.
curve for the inverse conversion. Press the [Step] button and enter a gamma strength
(step) in the numeric keypad window. The effect
Standard: Use standard. changes in increments of 0.05.
Press the button on the right of the [Standard] Press the [Level] button and enter a gamma
button and enter a table number (1 to 7) in the strength (level) in the numeric keypad window.
numeric keypad window. Hyper: Use hypergamma.
Hyper: Use hypergamma. Press the button on the right of the [Hyper] button
Press the button on the right of the [Hyper] button and enter a table number (1 to 4) in the numeric
and enter a table number (1 to 4) in the numeric keypad window.
keypad window.
294
[HDR Converter] window > [Additional Returning [HDR Converter] window
Paint] tab settings to the initial settings
Adjusts the image quality of the input signal. Press the [Default Recall] button in the [HDR Converter]
window.
1 Set the [Additional Paint] button to the on state. The settings on all tabs in the [HDR Converter] window
are returned to the following values.
When not adjusting the image quality, set the [Config] tab: System settings values
[Additional Paint] button to the off state. [Conversion] tab: System settings values
[Additional Paint] tab: Default values
2 Set the white balance function using the [White
Balance] button.
On: Adjust the white balance.
Press the [R] button and enter an R gain value in
the numeric keypad window.
Press the [B] button and enter a B gain value in the
numeric keypad window.
Off: Do not adjust the white balance.
Notes
• This cannot be set when the input signal conversion
mode is set to [Air Matching Off] or [Display
Referred].
• When the input signal OETF is set to [PQ], [S-Log3
(HDR)], or [S-Log3 (Live HDR)], [Natural] cannot
be selected for [Input Look] and [Output Look].
• When the input signal OETF is set to [SDR], [Input
Look] and [Output Look] cannot be set.
295
Note
Setting the Output Signal An AUX output signal cannot be assigned to more
than one output. When multiple outputs are selected,
the [Aux] and [Aux Mix] tab are not displayed.
This section describes how to set the switcher output
signal.
The number of outputs will vary depending on the system
5 Press [OK].
signal format. Assignable signals
2160P format: [PP/ME Out] tab:
Outputs: Max. 12 P/P Out1 to P/P Out8 1)
Outputs configurable with color corrector/HDR M/E-x Out1 to M/E-x Out8 (“x” is 1 to 5) 1)
converter: Max. 3 [CB/DME/FM/Clip/MV] tab:
Outputs configurable with format converter: 6 (odd- Undefined (when signal is not assigned)
numbered outputs only) Color Bkgd2
1080P, 1080i formats: DME Monitor Video
Outputs: Max. 24 DME Monitor Key
Outputs configurable with format converter: 12 Frame Memory1 to Frame Memory16
(outputs 1 to 12 only) Clip Player1 to Clip Player4
Multi Viewer1 to Multi Viewer2
Notes [Aux] tab:
Aux1 to Aux48
• Outputs 13 to 18 can be used when an XKS-G1110 Edit Preview
Additional I/O Board (option) is installed. Preset
Outputs 19 to 24 can be used when two XKS-G1110 [Aux Mix] tab:
Additional I/O Boards (option) are installed. Aux1/2 to Aux47/48
• When the system signal format is 1080P or 1080i, a color
corrector/HDR converter cannot be used. 1) The assigned signal name is displayed in the Home > Setup > Switcher >
Config > M/E Config menu (19103.12).
To select and set multiple outputs, place a check mark • Configurable only when the system signal format is
beside the target outputs to set. 2160P.
To select and set all outputs, place a check mark in the • Up to three outputs can be configured with a color
Select All checkbox. corrector/HDR converter.
3 Press the [Edit] button. 1 Open the Home > Setup > System > Output > Output
Assign menu (19101.41).
The [Output Assign] window appears.
2 Select the target output to set.
4 Set the button for the signal to assign to the on state.
To select and set multiple outputs, place a check mark
Select a tab to change the type of signal to display. beside the target outputs to set.
[PP/ME Out] tab: Switcher bank outputs
[CB/DME/FM/Clip/MV] tab: Color background/ 3 Set the [CCR/HDR] switch to the on state.
DME/frame memory/clip player/multi viewer
outputs Note
[Aux] tab: AUX outputs
[Aux Mix] tab: AUX mix outputs If the maximum number of outputs that can be
configured has been reached, set the [CCR/HDR]
296
switch for one of the outputs to the off state and then
configure the outputs. Setting the Safe Title Area
1 Open the Home > Setup > System > Output > Safe
Title menu (19101.43).
Setting Through Mode
When through mode is enabled, the input signal ancillary 2 Select the target output to set.
data is passed to the output without change.
You can enable through mode for the following output 3 Set the safe title area display method.
signals. To display box 1
• AUX1 to AUX48 Set the [Box1] button to the on state.
• Edit preview Set the following parameter.
To select and set multiple outputs, place a check mark No. Parameter Adjustment
beside the target outputs to set. 1 Size Size
To select and set all outputs, place a check mark in the
2 Luminance Luminance
Select All checkbox.
In the [Box2 Adjust] group, select an aspect ratio
3 Enable/disable through mode using the [Through (16:9, 14:9, 4:3).
Mode] switch.
To display a cross
On: Enable through mode. Set the [Cross] button to the on state.
Off: Disable through mode.
To display a grid
Set the [Grid] button to the on state.
In the [Grid Adjust] group, select an aspect ratio (16:9,
Setting the Video Clip Function 4:3).
In the [Grid Size] group, select a size (80.00%,
1 Open the Home > Setup > System > Output > Video 85.00%, 90.00%, 100.00%).
Adjust menu (19101.42).
To return the settings to the defaults
2 Select the target output to set and set the following Press the [Reset] button.
parameters.
297
Note
To set the down-converter aspect ratio
Press the [Aspect] button and select an aspect ratio from
Field frequency and frame frequency conversion is not the pull-down list.
supported. Edge Crop: Crop the left and right sides of a 16:9 image
to convert it to a 4:3 image.
The signal formats that can be converted are given below. Letter Box: Add black bars on the top and bottom of a
16:9 image to convert it to a 4:3 image.
System signal format Signal format of output Squeeze: Compress a 16:9 image horizontally to covert it
(frequency) signal
to a 4:3 image.
2160P 2SI 1080i
(59.94, 50) 1080P Image before conversion Image after conversion (4:3)
2160P 2SI 3G a) (16:9)
2160P 2SI 12G
Edge Crop
1080P 720P
(59.94, 50) 1080i
1080P
1080i 480i
(59.94) 720P
1080i
1080i 576i Letter Box
(50) 720P
1080i
a) Only the first number output in each group of four outputs can be set. The
settings of the outputs in each group are linked and change accordingly.
1 Open the Home > Setup > System > Output > FC
Format menu (19101.44). Squeeze
298
Notes [HDR Converter] window > [Conversion]
tab
• To use the HDR converter function, the XZS-G1750
HDR Converter License (option) is required. Configure in the same way as for an input signal.
• When the system signal format is 1080P or 1080i, an
HDR converter cannot be used. For details, see “[HDR Converter] window >
[Conversion] tab” (page 294).
1 Open the Home > Setup > System > Output > HDR
Converter menu (19101.46). Notes
The system OETF, color space, and HDR settings are • This cannot be set when the system OETF and output
displayed in [System Settings]. signal OETF are set to [SDR].
• When converting from SDR to HDR, configure in the
2 Select the target output to set. same way as for an input signal as described in “When
converting from HDR to SDR”.
To select and set multiple outputs, place a check mark • When converting from HDR to SDR, configure in the
beside the target outputs to set. same way as for an input signal as described in “When
To select and set all outputs, place a check mark in the converting from SDR to HDR”.
Select All checkbox.
3 Press the [Output Signal OETF] button and select an [HDR Converter] window > [Additional
OETF from the pull-down list. Paint] tab
Select [SDR], [HLG], [PQ], [S-Log3 (HDR)], or Configure in the same way as for an input signal.
[S-Log3 (Live HDR)].
For details, see “[HDR Converter] window > [Additional
4 Press the [Color] button and select a color space from Paint] tab” (page 295).
the pull-down list.
Returning [HDR Converter] window
Select [BT.709] or [BT.2020].
settings to the initial settings
5 Enable/disable the system settings using the [Follow Press the [Default Recall] button in the [HDR Converter]
System Settings] switch. window.
The settings on all tabs in the [HDR Converter] window
On: Enable system settings. Apply the system settings are returned to the following values.
to the output signal. [Config] tab: System settings values
Off: Disable system settings. Apply different settings [Conversion] tab: System settings values
than the system settings to the output signal. [Additional Paint] tab: Default values
If the system settings are disabled, press the [Adjust
Details] button and configure the HDR conversion
settings in the [HDR Converter] window.
Enabling/Disabling an SDI Output
Note Connector
When multiple outputs are selected, the [Follow You can enable or disable the signal output for an SDI
System Settings] switch settings do not change in output connector.
unison. When disabled, no signal is output from the output
connector.
[HDR Converter] window > [Config] tab
Note
Configure in the same way as for an input signal.
To prevent radio wave interference from occurring,
For details, see “[HDR Converter] window > [Config] disable output connectors that do not have a cable
tab” (page 293). connected.
Note 1 Open the Home > Setup > System > SDI Output
Enable menu (19101.91).
Only the [Master Black (Abs.)] button and [HDR Black
Offset] button settings are available in the [Black Level] Buttons for the output connectors for boards installed
group for an output signal. in each slot are displayed.
299
2 Enable/disable using the button for the target output
connector to set.
On: Enable signal output.
Off: Disable signal output.
To enable all output connectors
Press the [All Enable] button.
300
Cross-Point Setup Chapter 22
[DME/FM/CLIP] tab: DME monitor, frame
Creating a Cross-Point memory, and clip player output signals
[PP/ME Out] tab: Switcher bank output signals
Assign Table
Note
Input signals 45 to 48 cannot be used.
You can create a main table (Main) and up to 14 other
tables (Table1 to Table14) as cross-point assign tables.
You can configure the video signal and key signal
5 Press [OK].
combinations in the main table. When a signal is not assigned
On the [B/W/COLBKG] tab of the [Select Source]
window, select the [N/A] button.
Creating the Main Table The signal will not be switched even when the cross-point
button is pressed.
You can assign a signal pair consisting of a video signal
and a key signal to each cross-point button number. To delete a button number setting
You can also assign the same signals to multiple button Select the target button number to delete and press the
numbers to duplicate the assignment. [Delete] button.
The settings for all the button numbers not deleted move
1 Open the Home > Setup > Xpt Assign > Main, V/K up in sequence.
Pair Assign menu (19102.21). To insert a button number setting
The V/K pair number (cross-point button number), Select the button number at the insertion position and press
video signal source name and number, and key signal [Insert].
source name and number are displayed. A button number is inserted and the settings of all other
buttons are shifted by one.
2 Select the target button number to set. To return to the initial settings
To select and set multiple button numbers, place a Press the [Default Recall] button, check the message, then
check mark beside the target button numbers to set. press [OK].
To select and set all button numbers, place a check
mark in the Select All checkbox.
Creating Tables 1 to 14
3 Press the [Edit] button.
You can assign the V/K pair signals configured in the main
To set the video signal, press the [Edit] button for table to cross-point button numbers.
[Video].
To set the key signal, press the [Edit] button for [Key]. 1 Open the Home > Setup > Xpt Assign > Table Button
The [Select Source] window appears. Assign menu (19102.31).
4 Set the button for the source signal to assign to the on 2 Display the target table to set.
state.
Select a tab to change the table (Table1 to Table14) to
Select a tab to change the type of signal to display. display.
[Input] tab: Input signals
[B/W/COLBKG] tab: Black, white, and color 3 Select the target button number to set.
background signals
301
To select and set multiple button numbers, place a To select and set all tables, place a check mark in the
check mark beside the target button numbers to set. Select All checkbox.
To select and set all button numbers, place a check
mark in the Select All checkbox. 3 Press the [Xpt Shift Mode] button and select an
operation mode from the pull-down list.
4 Press the [Edit] button.
Hold: Functions as a shift button, and the shifted state
The [Select V/K Pair] window appears. of a cross-point button is enabled while the button
is pressed.
5 Set the button for the V/K pair signals to assign to the Lock: Functions as a shift button, and pressing a
on state. button toggles between the shifted and unshifted
states of the cross-point.
Select a tab to change the V/K pair number to display. Off: Functions as a cross-point button, namely, button
number 24 on a 24-button system or button
6 Press [OK]. number 16 on a 16-button system.
To inhibit operation
Select the target button number and set the [Inhibit] switch Setting the [SHIFT ALL] button operation
to the on state. mode
To delete a button number setting You can set the operation mode of the [SHIFT ALL]
Select the target button number to delete and press the button assigned to the function button section of the cross-
[Delete] button. point control block.
The settings for all the button numbers not deleted move The setting is common to all cross-point assign tables.
up in sequence.
1 Open the Home > Setup > Xpt Assign > Shift Mode
To insert a button number setting menu (19102.41).
Select the button number at the insertion position and press
[Insert]. 2 Set the operation mode using the [Shift All Hold]
A button number is inserted and the settings of all other button.
buttons are shifted by one.
On: Set to Hold mode. The shifted state of the cross-
To return to the initial settings point buttons for all buses is enabled while the
Press the [Default Recall] button, check the message, then [SHIFT ALL] button is pressed.
press [OK]. Off: Set to Lock mode. Each time the [SHIFT ALL]
button is pressed, the cross-points are switched
between the shifted and unshifted states for all
Setting the Shift Button buses.
Note
The [SHIFT] button operation mode is set by the settings
of the cross-point assign table of the switcher bank,
regardless of the buses assigned to the cross-point button
rows.
1 Open the Home > Setup > Xpt Assign > Shift Mode
menu (19102.41).
302
Assigning a Cross-Point Setting a Source Signal
Assign Table
Note
You can select a cross-point assign table to use for each Source signals “Primary 45 to 48” cannot be used. All
switcher bank or bus. settings are disabled.
1 Open the Home > Setup > Xpt Assign > Table Assign
menu (19102.11). Setting a Source Name
2 Select the target switcher bank or bus to set. You can set the name of a source signal.
To select and set multiple switcher banks/buses, place
a check mark beside the target switcher banks/buses to 1 Open the Home > Setup > Xpt Assign > Src Name/Src
set. Color > Edit Src Name/Color menu (19102.51).
To select and set all switcher banks/buses, place a
check mark in the Select All checkbox. 2 Select the target source signal to set.
To select and set multiple source signals, place a check
3 Press the [Table Assign] button and select a table mark beside the target source signals to set.
(Main, Table1 to Table14) from the pull-down list. To select and set all source signals, place a check mark
in the Select All checkbox.
Note
When multiple source signals are selected,
consecutively numbered source names are set.
For details, see “Name settings when multiple items
are selected” (page 43).
1 Open the Home > Setup > Xpt Assign > Src Name/Src
Color > Edit Src Name/Color menu (19102.51).
303
Changing the source color
Setting the Cross-Point
Note
304
3 Press the [Select Panel] button in the [Copy to Aux
Copying a Cross-Point Remote Panel] group.
The [Select Panel] window appears.
Assign Table
4 Select a copy destination remote panel and press [OK].
Copying a Table 5 Press the [Table Copy] button in the [Copy to Aux
Remote Panel] group.
You can copy settings between cross-point assign tables.
6 Check the message, then press [OK].
Note
Settings cannot be copied to the main table. It can only be
selected as a copy source.
1 Open the Home > Setup > Xpt Assign > Table Copy
menu (19102.71).
A list of copy source tables is shown on the left, and a
list of copy destination tables is shown on the right.
Notes
• The main table cannot be copied.
• After copying, the remote panel settings data is
overwritten.
• After copying, the function button settings on the remote
panel change as follows.
- Top left button: Status function
- Top right button: Source/Destination/Level function
- Bottom left button: Assign function
- Bottom right button: Lock Chop function
1 Open the Home > Setup > Xpt Assign > Table Button
Assign menu (19102.31).
305
Switcher Setup Chapter 23
When the system signal format is 1080P or 1080i, you
Setting the Switcher can select 0, 2, 4, 6, or 8.
Note
Assigning a Logical M/E
You can set how an M/E hardware block (physical M/E To use the SL key function, the XKS-G1600 GPU Pack
block) of the switcher is referred to logically as an M/E. (option) and XZS-G1620 SL Key License (option) are
You can assign M/E-1 to M/E-5 or P/P. required.
Also, when the system signal format is 2160P, the SL key
must be enabled.
Notes
• When M/E split is enabled, you can configure each sub 1 Open the Home > Setup > Switcher > Config > M/E
block. Assign menu (19103.11).
• It is not possible to assign the same M/E logical bank
more than once. The most recently assigned logical M/E 2 Select the target physical M/E block/sub block to set.
is enabled, and replaces the previous logical M/E setting.
3 Set the [SL Key] switch to the on state.
1 Open the Home > Setup > Switcher > Config > M/E
To disable an SL key, set the [SL Key] switch to the
Assign menu (19103.11).
off state.
2 Select the target physical M/E block/sub block to set.
3 Press the [M/E] button and select a logical M/E Setting the Operation Mode and
(M/E-1 to M/E-5, P/P) from the pull-down list. Output for a Switcher Bank
Setting Sub Block keys Setting the operation mode
When M/E split is enabled, you can configure the number
You can select from the following four operation modes
of keys assigned to each sub block.
for each switcher bank.
1 Open the Home > Setup > Switcher > Config > M/E Standard mode
Assign menu (19103.11). Four outputs are assigned as follows (fixed).
Out1: Program 1 output
2 Select the target sub block to set. Out2: Preview 1 output
Out3: Clean output
3 Press the [Number of assigned keys] button and select Out4: Key preview 1 output
the number of keys from the pull-down list.
Multi program mode
When the system signal format is 2160P, you can Up to eight outputs can be used.
select 0, 2, or 4. Out1: Program 1 output (fixed) is assigned.
306
Out2 to Out8: You can assign the following outputs. Notes
Program 1 to 4 outputs
Preview 1 output • The output configuration for standard mode and DSK
Clean output mode cannot be changed.
Key preview 1 and 2 outputs • Out1 is set to PGM1 (fixed).
When M/E split is enabled, Out5 to Out8 cannot be used. • When M/E split is enabled, Out5 to Out8 cannot be used.
Multi program 2 mode 1 Open the Home > Setup > Switcher > Config > M/E
Up to eight outputs can be used. Config menu (19103.12).
Out1: Program 1 output (fixed) is assigned.
Out2 to Out8: You can assign the following outputs. 2 Select the target switcher bank to set.
Program 1 to 4 outputs
Preview 1 and 2 outputs 3 Press the [Edit] button for [Output].
Clean output
Sub clean output The [Output] window appears.
Key preview 1 and 2 outputs
4 Press the button for the target output number (1 to 8)
DSK mode and select an output signal from the pull-down list.
Six outputs are assigned as follows (fixed).
Out1: Program 1 output 5 Press [OK].
Out2: Program 2 output
Out3: Program 3 output
Out4: Program 4 output Setting the program output
Out5: Key preview 1 output You can select the background and the keys to enable for
Out6: Key preview 2 output the program output.
When M/E split is enabled, four outputs are assigned as
follows (fixed). 1 Open the Home > Setup > Switcher > Config > PGM
Out1: Program 1 output Config menu (19103.13).
Out2: Program 2 output
Out3: Key preview 1 output 2 Select the target program output to set.
Out4: Key preview 2 output
3 Press the [Background] button and select a
Notes background from the pull-down list.
• When M/E split is enabled, multi program 2 mode You can select the following backgrounds.
cannot be selected. Standard mode: Clean
• DSK mode can be selected only when the switcher bank Multi program mode: Clean, Utility2
is assigned to P/P. Multi program 2 mode: Clean, Sub Clean 1), Background
A, Background B, Sub Background A 1), Sub
1 Open the Home > Setup > Switcher > Config > M/E Background B 1)
Config menu (19103.12). DSK mode: DSK Background 1 to 4
1) Cannot be selected on PGM1.
2 Select the target switcher bank to set.
4 Press the [Edit] button for [Key Enable].
3 Press the [M/E Config] button and select an operation
mode from the pull-down list. The [Key Enable] window appears.
307
change the keys to enable in the Common > Key 3 Press the [Edit] button for [Assigned M/E Output].
Priority/Key Assign menu of the switcher bank.
For details, see “To change program output key The [M/E Output Assign] window appears.
assignments” (page 182).
4 Set the button for the target output to the on state.
6 Press [OK].
5 Press [OK].
7 Press [OK].
2 Set the [Extended M/E Re-Entry] button to the on
state.
Setting a DSK mode background 3 Check the message, then press [OK].
In DSK mode, you can select a switcher bank output to
assign to a background (Background 1 to 4).
1 Open the Home > Setup > Switcher > Config > DSK
Bkgd Assign menu (19103.15).
308
Setting a DME Channel
Setting a Multi Viewer
Setting a DME channel to use in a switcher
bank A multi viewer is a function that splits the screen for
display of multiple images at the same time.
You can set a DME channel to use on switcher bank for a
When the system signal format is 2160P, you can use one
processed key or DME wipe.
multi viewer (multi viewer 1). When the system signal
format is 1080P or 1080i, you can use two multi viewers
1 Open the Home > Setup > Switcher > Config > DME
(multi viewer 1, multi viewer 2).
Config menu (19103.16).
1 Open the Home > Setup > Switcher > Config > User On: Display border lines on subscreen.
Region Config menu (19103.17). Off: Do not display border lines on subscreen.
Tally display
2 Select the target region to set. Tallies are shown on the multi viewer screen for the signals
To select and set multiple regions, place a check mark used in the on-air image.
beside the target regions to set. The tally is represented by subscreen borders using the
To select and set all regions, place a check mark in the following three colors.
Select All checkbox. Red: Image with red tally (on-air tally)
Green: Image with green tally
3 Press the [User Region] button and select a user region Yellow: Image with yellow tally
(User 1 to User 8) from the pull-down list.
Note
When you do not want to assign a user region
Select [No Assign] from the pull-down list. When [Independent] is selected in the [Tally Type] group
in the Home > Setup > Panel > Custom > Button Tally
To return to the previous setting menu (19104.64), tallies are not displayed on the multi
Press the [Clear] button. viewer screen.
309
To display the signal names of all subscreens
Assigning Signals Set the [Enable All Names] button to the on state.
Note
1 Open the Home > Setup > Switcher > Multi Viewer
menu (19103.21).
Note
Input signals 45 to 48 cannot be used.
5 Press [OK].
1 Open the Home > Setup > Switcher > Multi Viewer
menu (19103.21).
310
Setting a DME External Setting the Transition
Input (Ext In) Mode
You can set the signal (AUX bus output) that is input on
Ext In on a DME. Setting the Transition Preview Mode
You can set the transition preview mode for when the
1 Open the Home > Setup > Switcher > DME Interface
[TRANS PVW] button is pressed.
menu (19103.31).
311
1 Open the Home > Setup > Switcher > Custom > 2 In the [FTB] group, select the program outputs (PGM1
Transition menu (19103.41). to PGM4) to enable.
3 Enable/disable using the [Bus Toggle] switch. When the switcher bank operation mode is standard
mode, the [PGM2] to [PGM4] buttons cannot be
On: Flip-flop mode selected.
Off: Bus fixed mode
On: Return to previous transition type after a 1 Open the Home > Setup > Switcher > Custom >
transition ends. Transition menu (19103.41).
Off: Maintain a preset color mix after a transition
ends. 2 In the [Fader Curve] group, select a fader lever
operation mode.
Normal: The transition progresses according to the
Enabling/Disabling Fade-To-Black fader lever position.
A tally is output at the same time the transition
You can enable/disable fade-to-black for each program
starts.
output (PGM1 to PGM4).
Adv Tally Mode: When the fader lever is moved from
the end of its travel, a tally is output before the
1 Open the Home > Setup > Switcher > Custom >
Transition menu (19103.41).
312
transition starts due to a slight hysteresis
characteristic at the beginning of the fader curve.
Keys/Wipes
313
The cross-point hold operation mode is also applied to 3 Press the [Wipe Edge Default] button and set the
snapshot attributes. following parameter.
1 Open the Home > Setup > Switcher > Custom > Key/ No. Parameter Adjustment
Wipe menu (19103.43).
1 Soft Default value of wipe edge
softness
2 Select the target switcher bank to set.
2 Select the target switcher bank to set. 3 Press the [Edit] button for [Key Auto Drop].
The [Set Key Auto Drop] window appears.
3 Press the [Pattern Limit Transition] button and select
an operation mode for when a pattern limit is released 4 Place a check mark in the keys to set.
from the pull-down list.
Auto: When the pattern limit is released, the 5 Press [OK].
remainder of the transition is executed
automatically at a dedicated transition rate.
Manual: After the pattern limit is released, the
transition waits for the next operation, then
executes. The transition is not executed until you
operate the fader lever or press the [AUTO
TRANS] button.
314
Control Panel Setup
Note
Chapter 24
Setting the Control Panel When dual M/E is enabled, you can set main and sub
Configuration to the shifted state and unshifted state of a switcher
bank assigned to two M/E banks.
The shifted/unshifted settings for dual M/E are
cleared.
Assigning a Switcher Bank For details about dual M/E, see “Setting Dual M/E”
(page 316).
You can select the switcher bank to assign to an M/E bank.
The M/E bank number indicates a physical position on the
control panel. On a control panel with two M/E bank rows,
the rows are numbered 1 and 2 from the back. Inhibiting Switcher Bank Operation
1 Open the Home > Setup > Panel > Config > M/E You can inhibit operation of switcher bank assigned to an
Assign menu (19104.11). M/E bank.
2 Select the target M/E bank to set. 1 Open the Home > Setup > Panel > Config > M/E
Assign menu (19104.11).
3 Press the [Assign] button and select a switcher bank
(M/E-1 to M/E-5, P/P) from the pull-down list. 2 Select the target switcher bank to set.
To assign no switcher bank, select [- - -]. 3 Press the [Operation] button and select an operation
setting from the pull-down list.
Enable: Enable panel display and operation of the
Setting Switcher Banks in Multi switcher bank.
Program 2 Mode Disable: Enable panel display only, and inhibit
operation of the switcher bank.
In multi program 2 mode, you can set main/sub for each Inhibit: Turn off panel display and inhibit operation
switcher bank assigned to an M/E bank. of the switcher bank.
You can select dedicated main, dedicated sub, or shared
main and sub. Note
1 Open the Home > Setup > Panel > Config > M/E When selecting a region from the taskbar, switcher
Assign menu (19104.11). banks with operation inhibited cannot be selected.
315
• Flexi Pad control block 2 Press the [Dual M/E Xpt Swap] button.
1 Open the Home > Setup > Panel > Config > M/E On: Set the M/E bank with the higher number to the
Assign menu (19104.11). unshifted state, and the M/E bank with the lower
number to the shifted state.
The status of the key inhibit settings are displayed in Off: Set the M/E bank with the higher number to the
[Key Inhibit]. shifted state, and the M/E bank with the lower
Keys with an inhibit setting are displayed in white number to the unshifted state.
characters.
In multi program 2 mode, the status of main and sub
keys is displayed. Setting Regions Selected
2 Select the target switcher bank to set. Simultaneously
3 Press the [Edit] button for [Key Inhibit]. You can set the regions that are selected simultaneously
when using the [All Regions] button in the effect timeline
The [Key Inhibit] window appears. and snapshot menus.
4 Place a check mark in the keys to inhibit operation. 1 Open the Home > Setup > Panel > Config > All
Regions Assign menu (19104.12).
5 Press [OK].
2 Select the target region to set.
To select and set multiple regions, place a check mark
Setting Dual M/E beside the target regions to set.
To select and set all regions, place a check mark in the
You can assign the cross-points for the shifted state and Select All checkbox.
unshifted state of a single switcher bank to two
consecutive M/E banks. 3 Set the [Assign] switch to the on state.
If there are two M/E banks, dual M/E is configured for the
switcher bank on M/E bank 1.
Notes
• Cannot be set if there is only one M/E bank.
• Cannot be set if a switcher bank has not been assigned to
the M/E bank.
1 Open the Home > Setup > Panel > Config > M/E
Assign menu (19104.11).
1 Open the Home > Setup > Panel > Config > M/E
Assign menu (19104.11).
316
To return assignable button assignments to the
Assigning Control Panel defaults
Press the [Default Recall] button, check the message, then
Buttons press [OK].
1 Open the Home > Setup > Panel > Module > Button
Assign menu (19104.21).
An image of the entire control panel appears.
Each control block is enclosed by a white frame.
Note
5 Press [OK].
317
7 Press [OK].
Assigning a Utility To set a name
Press the [Name] button and enter a name (up to 8
Function characters) using the keyboard.
When multiple buttons are selected, consecutively
numbered names are set.
You can assign the following functions (actions) to the
memory recall buttons in the utility control block and the For details, see “Name settings when multiple items are
cross-point buttons in the cross-point control block. selected” (page 43).
• Utility command
• Recalling a macro register To release the assignment
• Recalling a shotbox register Select the target button to release and press the [Clear]
• Menu shortcut button.
Select a tab to change the control block to display. 3 Select the target button to set.
[Utility Module] tab: Utility control block
[XPT Module] tab: Cross-point control block The target button to set is displayed in “bank number-
button number” format.
3 Select the target button to set. To select and set multiple buttons, place a check mark
beside the target buttons to set.
The target button to set is displayed in “bank number- To select and set all buttons, place a check mark in the
button number” format. Select All checkbox.
To select and set multiple buttons, place a check mark
beside the target buttons to set. 4 Press the [Action Group] button and select [Macro
To select and set all buttons, place a check mark in the Recall] or [Shotbox Recall] from the pull-down list.
Select All checkbox.
5 Press the [Edit] button for [Action] and enter a register
4 Press the [Action Group] button and select [Util number to assign in the numeric keypad window.
Command] from the pull-down list.
To release the assignment
5 Press the [Edit] button for [Action]. Select the target button to release and press the [Clear]
button.
The [Select Action] window appears.
Assigning a menu shortcut
6 Set the button for the command to assign to the on
state. You can assign a menu shortcut function to a button.
You can set the name to display on the memory recall
Select a tab to change the action to display. buttons in the utility control block and on the display in the
[Safe Title] tab: Safe title setup commands cross-point control block.
[GPI Test Fire] tab: GPI trigger test output
commands
[Others] tab: Other commands
318
Note
319
A list of button rows is shown on the left and a list of
Setting Cross-Point assignable buses/banks is shown on the right.
Button Rows in the 3 In the list on the left, select the target button row (1 to
4) to set.
Cross-Point Control
4 In the list on the right, select a bus/bank to assign.
Block
5 Press the [Set] button.
To return the assignment to the defaults
Setting the Operation Mode of a Press the [Default Recall] button, check the message, then
Button Row press [OK].
You can set the operation mode of a cross-point button row Setting the key/AUX bus delegation mode
in the cross-point control block. button row
For details about operation modes, see “Operation Mode You can assign bus or utility/shotbox mode bank
of Cross-Point Button Rows” (page 47). delegation buttons to the 1st row in key/AUX bus
delegation mode.
Note 1 Open the Home > Setup > Panel > Xpt Module > Key
When a switcher bank is shared on main and sub in multi Deleg/AUX Assign menu (19104.33).
program 2 mode, the operation mode of main and sub
button rows are linked. 2 Display the target switcher bank to set.
Select a tab to change the switcher bank to display.
1 Open the Home > Setup > Panel > Xpt Module >
A list of 1st row button numbers is shown on the left
Operation Mode menu (19104.31).
and a list of assignable buses/banks is shown on the
right.
2 Display the target switcher bank to set.
Select a tab to change the switcher bank to display. 3 In the list on the left, select the target button number to
set.
3 In the [Row Mode] group, select an operation mode.
4 In the list on the right, select a bus/bank to assign.
Key Bus: Key bus mode
Free Assign: Free assign mode 5 Press the [Set] button.
Key Deleg/AUX: Key/AUX bus delegation mode
To return the assignment to the default
Press the [Default Recall] button, check the message, then
Setting a button row in free assign mode press [OK].
In free assign mode, you can assign a bus or utility/shotbox
mode bank to the 1st row to 4th row.
Setting Buttons and Indicators
Note
You can also set the 1st row to 4th row using delegation Setting the on/off state of cross-point
buttons assigned to the function button section.
indicators
For details about function buttons, see “Cross-Point Cross-point indicators light up in the source color of the
Control Block” (page 15). video signal assigned to buttons on the 3rd row in the
cross-point control block.
1 Open the Home > Setup > Panel > Xpt Module > Free You can disable the cross-point indicators so that they do
Assign menu (19104.32). not turn on.
2 Display the target switcher bank to set. 1 Open the Home > Setup > Panel > Xpt Module >
Operation Mode menu (19104.31).
Select a tab to change the switcher bank to display.
2 Display the target switcher bank to set.
320
Select a tab to change the switcher bank to display. When the [Split] switch is set to the off position
Press the [Lower Area] button and select an item to
3 Set the on/off state of cross-point indicators using the display from the pull-down list.
[Xpt Indicator] button.
To make the display background gray
On: Lit Set the [Gray Bkgd] switch to the on state.
Off: Not lit
To return the settings to the defaults
Press the [Default Recall] button, check the message, then
Setting the color of cross-point buttons press [OK].
You can set the color of the 3rd row/4th row cross-point
buttons.
Setting Utility Bus Mode
1 Open the Home > Setup > Panel > Xpt Module >
Operation Mode menu (19104.31). In utility bus mode, you can set the bus assigned to the 1st
row to 4th row in the cross-point control block.
2 Display the target switcher bank to set.
For details about utility bus mode, see “Utility bus mode”
Select a tab to change the switcher bank to display. (page 49).
3 In the [Xpt Button Color] group, select a color. 1 Open the Home > Setup > Panel > Xpt Module > Util
Source Color: Light up in the source color set for the Button Bus Assign menu (19104.35).
video signal.
2 Display the target switcher bank to set.
For details about source color, see “Setting the Source
Color” (page 303). Select a tab to change the switcher bank to display.
A list of button rows is shown on the left and a list of
White: Light up white. assignable buses is shown on the right.
You can set the information that appears on the display in 4 In the list on the right, select a bus to assign.
the cross-point control block.
The display items and format can be selected for each of 5 Press the [Set] button.
six display modes.
To release the assignment
1 Open the Home > Setup > Panel > Xpt Module > In the list on the left, select the target button row (1 to 4) to
Display Mode menu (19104.34). release and press the [Clear] button.
To return the assignment to the defaults
2 Display the target switcher bank to set. Press the [Default Recall] button, check the message, then
Select a tab to change the switcher bank to display. press [OK].
321
Note
Setting External Devices A port configured with a P-Bus compatible device
cannot be assigned to a channel selection button.
Setting the P-Bus Control Mode 3 Press the [Device Channel] button and select a channel
(Device Ch1 to Device Ch12) from the pull-down list.
You can set the mode for controlling P-Bus compatible
devices. Configuring file list sharing
For details, see “P-Bus control modes” (page 173). You can configure sharing of the same file list, for
example, when the same device is connected to multiple
1 Open the Home > Setup > Panel > External Device > ports.
GPI/P-Bus menu (19104.41).
Note
2 In the [P-Bus Control] group, select a P-Bus control
File list sharing is enabled only for ports to which a disk
mode.
recorder (video disk communications protocol or Odetics
Trigger: P-Bus trigger protocol) has been assigned.
Timeline: P-Bus timeline
1 Open the Home > Setup > Panel > External Device >
Device Channel Assign menu (19104.42).
Setting the AUX Bus Override Mode 2 Select the target port to set.
You can set the operation mode when “Aux1 to 48 Bus
Override” is selected if the trigger type is set to “Rising 3 Press the [Same File List Channel] button and select a
Edge” or “Falling Edge” for a GPI input. channel (Device Ch1 to Device Ch12) for sharing a
file list from the pull-down list.
1 Open the Home > Setup > Panel > External Device >
GPI/P-Bus menu (19104.41).
1 Open the Home > Setup > Panel > External Device >
Device Channel Assign menu (19104.42).
322
2 In the list on the left, select the target button to set.
Setting a Router You can also press the [Select Button] button and enter
a button number in the numeric keypad window.
• A source table cannot be selected on buttons with button 1 Open the Home > Setup > Panel > Router > Source
numbers 65 to 128. Table Assign menu (19104.52).
• Operation inhibit cannot be configured for buttons with
button numbers 65 to 128. 2 Display the target source table to set.
1 Open the Home > Setup > Panel > Router > Delegation Select a tab to change the source table (Src Table1 to
Button Assign menu (19104.51). Src Table5) to display.
A list of delegation buttons to which to assign a source
A list of delegation buttons to which to assign a is shown on the left and a list of assignable sources is
destination is shown on the left and a list of assignable shown on the right.
destinations is shown on the right.
3 In the list on the left, select the target button to set.
2 In the list on the left, select the target button to set.
You can also press the [Select Button] button and enter
You can also press the [Select Button] button and enter a button number in the numeric keypad window.
a button number in the numeric keypad window.
4 In the list on the right, select a source to assign.
3 In the list on the right, select a destination to assign.
You can also press the [Select Source] button and enter
You can also press the [Select Destination] button and a source number in the numeric keypad window.
enter a destination number in the numeric keypad
window. 5 Press the [Set] button.
Setting the recall target for a snapshot 1 Open the Home > Setup > Panel > Router > Level
You can set whether a destination is the recall target when Button Assign menu (19104.53).
a snapshot of the router is recalled.
2 Select the target level selection button (1 to 4) to set.
Note
3 Press the [Edit] button for [Level Assign].
When operation inhibit is enabled, destination recall is not
available. The [Enable Level] window appears.
1 Open the Home > Setup > Panel > Router > Delegation 4 Place a check mark in the levels (1 to 8) to enable.
Button Assign menu (19104.51).
5 Press [OK].
323
Notes
Setting the Display/ • When the [NS-Bus Name Link] button is set to the on
Operation Mode state, the settings of all source names for the switcher
(including wiring traceback), not just in the Home >
Setup > Xpt Assign menu, are always replaced by the
NS-Bus alias name.
Setting Source Names and • To display the NS-Bus alias name on a multi viewer
subscreen, you must set the [NS-Bus Alias] button in the
Destination Names [Source/Dest Name] group to the on state and set the
You set the source name and destination name to use in the [NS-Bus Name Link] button to the on state.
control panel.
1 Open the Home > Setup > Panel > Custom > Operation
Mode menu (19104.61).
Note
The group number of an NS-Bus alias name must be set 2 Set the [NS-Bus Name Link] button to the on state.
beforehand.
3 Check the message, then press [OK].
For details, see “Selecting an Alias Name Group”
(page 340).
Setting the Transition Operation
1 Open the Home > Setup > Panel > Custom > Operation
Buttons and Display Mode
Mode menu (19104.61).
2 In the [Source/Dest Name] group, select a name to use Setting the transition rate display
in the control panel.
Sw’er Local: Use the name set on the switcher. 1 Open the Home > Setup > Panel > Custom > Operation
NS-Bus Alias: Use the NS-Bus alias name set in LSM Mode menu (19104.61).
(Live System Manager).
2 In the [Trans Rate Display] group, select a display
3 In the [Name Display Mode] group, select a display mode.
mode.
Frame: Display as number of frames.
Auto: Display four characters per line, up to four lines. Timecode: Display as timecode.
2 Characters: Display first two characters on one line.
4 Characters: Display first four characters on one Setting the operation when the [FTB]
line.
button is pressed during fade-to-black
Notes 1 Open the Home > Setup > Panel > Custom > Operation
• Line breaks in names are enabled only when [Auto] Mode menu (19104.61).
is selected.
• Up to two lines are displayed when the display mode 2 In the [FTB] group, select an operation mode.
is set to split display.
Continue: Continue the transition.
Cancel: Cancel the transition and return to the
Enabling the alias name link function previous state before executing fade-to-black.
When the link function is enabled, you can replace a
source name set on the switcher with an NS-Bus alias Setting the independent key transition,
name set in LSM. auto transition execution button display
The source name is updated each time the alias name is
updated. This allows you to always use the same name
between LSM and the switcher. Note
The NS-Bus alias name is reflected in the source name Enabled using a [KEY1 TRANS] to [KEY8 TRANS]
setting in the Home > Setup > Xpt Assign menu, hence the button in the transition control block.
name set in LSM is also displayed when the [Sw’er Local]
button in the [Source/Dest Name] group is set to the on
state.
324
1 Open the Home > Setup > Panel > Custom > Operation 2 In the [Bkgd Trans Btn Double Click] group, select
Mode menu (19104.61). whether to enable/disable the double-press function.
2 In the [Key Trans On Status] group, select a display Disable: Disable button double-press.
mode. Enable: Enable button double-press.
Setting the operation when an auto 2 In the [Trans PVW] group, select an operation mode.
transition execution button is pressed
during an auto transition Hold: Enables transition preview mode only while the
[TRANS PVW] button is pressed.
Lock: Pressing the [TRANS PVW] button switches
Note between transition preview mode and normal
Enabled using the [AUTO TRANS] button and a [KEY1 mode each time the button is pressed.
TRANS] to [KEY8 TRANS] button in the transition
control block. Swapping the [AUTO TRANS] button and
[CUT] button in the transition control block
1 Open the Home > Setup > Panel > Custom > Operation
Mode menu (19104.61).
1 Open the Home > Setup > Panel > Custom > Operation
Mode menu (19104.61).
2 In the [Auto Trans] group, select an operation mode.
Continue: Continue the transition. 2 Press the [Auto Trans/Cut Swap] button.
Cancel: Cancel the transition and return to the
On: Swap the [AUTO TRANS] button and [CUT]
previous state before executing the transition.
button.
Off: Do not swap the [AUTO TRANS] button and
Setting the next transitions to select using [CUT] button.
the [ALL] button in the transition control
block Setting the transition indicator display in
non-sync state
1 Open the Home > Setup > Panel > Custom > Operation
Mode menu (19104.61). 1 Open the Home > Setup > Panel > Custom > Operation
Mode menu (19104.61).
2 In the [Next Trans All] group, select a button to
include for the next transition. 2 In the [Non Sync Fader Indicator] group, select a
You can select multiple buttons. display mode.
Bkgd: [BKGD] button Normal: The transition indicator is lit when in non-
Key Priority: [KEY PRIOR] button sync state.
Key1 to Key8: [KEY1] button to [KEY8] button Blink: The transition indicator blinks when in non-
sync state.
Enabling double-press for the [BKGD]
button in the transition control block
When double-press is enabled, pressing the [BKGD]
button twice in quick succession selects all currently
inserted keys and removes them in the next transition.
1 Open the Home > Setup > Panel > Custom > Operation
Mode menu (19104.61).
325
Setting the button display in snapshot
Setting the Mode of Buttons in the operation mode
Cross-Point Control Block You can set the memory recall button display in snapshot
operation mode.
Setting the operation mode of the [UTIL]
button in the cross-point control block 1 Open the Home > Setup > Panel > Custom > Flexi Pad
Mode menu (19104.62).
1 Open the Home > Setup > Panel > Custom > Operation
2 In the [Snapshot Display] group, select a button
Mode menu (19104.61).
display.
2 In the [Util Button] group, select an operation mode. Register No.: Display register number.
Register Name: Display register name.
Hold: Enables utility bus mode only while the [UTIL]
button is pressed.
Lock: Pressing the [UTIL] button switches between Assigning a register to bottom left button
utility bus mode and normal mode each time the of bank 0
button is pressed.
You can assign a register to the bottom left memory recall
button when bank 0 is selected in snapshot operation
Setting the operation mode of the [KEY] mode/shotbox operation mode/macro operation mode.
button in the cross-point control block
You can set the signal to select on the key source bus.
1 Open the Home > Setup > Panel > Custom > Flexi Pad
Mode menu (19104.62).
1 Open the Home > Setup > Panel > Custom > Operation
2 Set the [Activate] button in the [Bank 0 Register
Mode menu (19104.61).
Assign] group to the on state.
2 In the [Key Source Bus Select Mode] group, select an
3 Press the [Register No.] button in the [Bank 0 Register
operation mode.
Assign] group and enter a register number in the
Key: The [KEY] button is always lit and only key numeric keypad window.
signals can be selected.
To release the register assignment
Video & Key: Enables key signals or video signals to
Set the [Activate] button in the [Bank 0 Register Assign]
be selected using the [KEY] button operation.
group to the off state.
Setting the Mode of Buttons in the Switching the operation mode in sync with
the transition control block
Flexi Pad Control Block
You can switch the operation mode of the Flexi Pad
control block in sync with the selection of the [WIPE]
Setting the button display in wipe button or [DME] button in the transition control block.
snapshot operation mode/DME wipe
snapshot operation mode 1 Open the Home > Setup > Panel > Custom > Flexi Pad
Mode menu (19104.62).
You can set the memory recall button display in wipe
snapshot operation mode/DME wipe snapshot operation 2 Set the [Wipe/DME Auto Deleg] button to the on state.
mode.
To release the link
1 Open the Home > Setup > Panel > Custom > Flexi Pad Set the [Wipe/DME Auto Deleg] button to the off state.
Mode menu (19104.62).
326
Setting the Mode of Buttons and Setting the Effect Timeline Mode
Trackball in the Device Control Block
Inserting the first keyframe automatically
Setting the trackball sensitivity when an empty register is recalled
You can set the sensitivity (degree of movement of an
image) for when the trackball/Z-ring is operated.
1 Open the Home > Setup > Panel > Custom > Effect
TL/Macro Mode menu (19104.63).
327
Setting the operation of the first keyframe
when a register is recalled
Setting the Macro Mode
1 Open the Home > Setup > Panel > Custom > Effect Setting the macro execution mode
TL/Macro Mode menu (19104.63).
1 Open the Home > Setup > Panel > Custom > Effect
2 In the [Recall Mode] group, select an action for the TL/Macro Mode menu (19104.63).
first keyframe.
Recall: Do not execute the first keyframe when a
2 In the [Macro Execution Mode] group, select a macro
execution mode.
register is recalled.
Recall&Rewind: Execute the first keyframe when a Normal: Normal execution mode
register is recalled. Step: Step execution mode
1 Open the Home > Setup > Panel > Custom > Effect 2 Set the [Macro Multi Recall Mode] button to the on
TL/Macro Mode menu (19104.63). state.
2 In the [Run 2nd Press Mode] group, select an operation To disable multi mode
mode. Set the [Macro Multi Recall Mode] button to the off state.
2 In the [Rewind&1st KF] group, set the button for the 1 Open the Home > Setup > Panel > Custom > Effect
target effect timeline to the on state. TL/Macro Mode menu (19104.63).
GPI: GPI timeline 2 In the [Macro 2nd Recall Mode] group, select an
P-Bus: P-Bus timeline operation mode.
DDR/VTR: DDR/VTR timeline
Macro: Macro timeline Cancel: Terminate the executing/paused macro.
Continue: Resume execution of a paused macro or
To disable the setting continue execution of an executing macro when a
In the [Rewind&1st KF] group, set the button for the target macro executed in a macro attachment is recalled
effect timeline to the off state. using the same button. Start execution from the
328
first event when the macro is recalled by any
method other than a macro attachment. Setting High Tally
You can select a tally to reflect in the control panel.
Setting the operation of buttons when
configuring a macro attachment 1 Open the Home > Setup > Panel > Custom > Button
Tally menu (19104.64).
1 Open the Home > Setup > Panel > Custom > Effect
TL/Macro Mode menu (19104.63). 2 In the [Tally Type] group, select a tally.
R1 to R8: Red tally in tally group 1 to 8
2 In the [Attachment Setting Mode] group, select an
Independent: Tally generated by the switcher
operation mode.
To return to the previous setting
With Button Function: Simultaneously execute
Press the [Clear] button.
button function.
W/o Button Function: Do not execute button
function.
3 Press the [Apply] button.
1 Open the Home > Setup > Panel > Custom > Effect
TL/Macro Mode menu (19104.63).
Note
Buttons for selected cross-points do not light up green
even when a macro attachment has been configured.
1 Open the Home > Setup > Panel > Custom > Effect
TL/Macro Mode menu (19104.63).
329
Setting the Lit State of Buttons
Adjusting the Control When Off
Panel Buttons/Display
1 Open the Home > Setup > Panel > Button/Display
Adjust menu (19104.71).
Setting Sleep Mode 2 Press the [Panel Glow] button.
You can enable sleep mode on the control panel. On: Set buttons to dimly lit state when off.
In sleep mode, the brightness of the buttons and display on Off: Set buttons to not lit state when off.
the control panel is reduced.
330
External Device Setup
Note
Chapter 25
Setting Parallel Input Ports on boards 2 and 3 can be used when an
Ports XKS-G1700 Legacy Interface Board (option) is
installed.
The use of parallel input ports is assigned in the following 3 In the list on the right, select the GPI input to assign.
priority sequence.
1. External box settings in the Home > Setup > Router/ 4 Press the [Set] button.
Tally > NS-Bus > Matrix menu (19106.11). To release a GPI input assignment
Assigned to external boxes according to the parallel Select the target parallel input port to release and press the
input port priority. [No Assign] button.
2. Tally settings in the Home > Setup > Router/Tally >
Tally > Tally Enable menu (19106.23).
Tally input is assigned to the selected parallel input
port.
3. GPI input port settings in the Home > Setup >
External Device > Input Config menu (19105.11).
2 In the list on the left, select the target parallel input port
to set.
The number for a parallel input port is displayed in
“board (1 to 3)-number (1 to 6)” format (for example,
“1-3”).
331
When the trigger type is [Level]
Setting a GPI Input Configure the action and high level/low level settings.
Press the [Action] button and select an action from the
pull-down list.
Press the [High Level] button and select a high-level
You can configure the trigger type and action for each GPI
setting from the pull-down list.
input.
Press the [Low Level] button and select a low-level
GPI input via a network setting from the pull-down list.
On GPI inputs via a network, GPI control is performed
using serial tally protocol commands. Note
GPI inputs can be configured in the same way as parallel
input ports. On GPI inputs via a network, the “System Format”
action is not supported when the trigger type is
[Level].
Note
This uses a serial tally port, hence the network port must 7 Press [OK].
be configured for a serial tally port.
To set action preferences
You can set action preferences when a register recall
For details, see “Setting a Serial Tally” (page 345).
action or AUX bus override action is selected.
1 Open the Home > Setup > External Device > GPI
1 Select the target GPI input to set.
Input Assign > GPI Input Assign menu (19105.21).
Rising Edge: Trigger on the rising edge of the input When an AUX bus override action is selected
pulse. Press the [Source No.] button and enter a source signal
Falling Edge: Trigger on the falling edge of the input (input signal) number in the numeric keypad window.
pulse.
Any Edge: Trigger on an inversion of the input pulse. Note
Level: Trigger the specified action when the level of
the input pulse is low or high. Source signal numbers 45 to 48 cannot be used.
NOP (No Operation): Not triggered by an input
pulse. 4 Press [OK].
Trigger type and actions list 1)
5 Press the [Edit Action] button for [Action]. When the trigger type is other than [Level]:
The [GPI Input Assign] window appears. P/P Cut, P/P Sub Cut, P/P Keyx Cut, M/E-x Cut, M/E-x
Sub Cut, M/E-x Keyx Cut
6 Select an action to set. P/P Auto Trans, P/P Sub Auto Trans, P/P Keyx Auto
Trans, M/E-x Auto Trans, M/E-x Sub Auto Trans, M/E-x
When the trigger type is other than [Level] Keyx Auto Trans
Select a tab to change the action type to display. FTB Cut, FTB Auto Trans, Effect Recall, Effect Recall &
[PP/ME Cut] tab: Cut transition actions Run, Effect TL Rewind, Effect TL Run, Effect TL Stop,
[PP/ME Auto Transition] tab: Auto transition Snapshot Recall, Shotbox Recall, Macro Recall, Macro
actions Take
[FTB/Effect/SS/SB/Macro] tab: FTB, effect P/P Keyx SS Recall, M/E-x Keyx SS Recall, No Action
timeline, snapshot, shotbox, and macro actions Auxx Bus Override 2)
[PP/ME Key SS Recall] tab: Key snapshot actions When the trigger type is [Level]:
[Aux Bus Override] tab: AUX bus override actions No Action, System Format
Set the button for the target action to the on state.
332
1) “M/E-x” is M/E-1 to M/E-5
”Keyx” is Key1 to Key8
”Auxx” is Aux1 to Aux48
2) When the trigger type is [Rising Edge] or [Falling Edge] only
Setting Parallel Output
Ports
Notes
1 Open the Home > Setup > External Device > GPI
Input Assign > H/L Format menu (19105.22). Assigning a GPI Output
2 Select the target format number to set. 1 Open the Home > Setup > External Device > Output
Config menu (19105.31).
3 Press the [H/L Name] button and enter a format name
(up to 16 characters) using the keyboard. A list of parallel output ports is shown on the left and
a list of GPI outputs is shown on the right.
4 Press the [Signal Format] button and select a signal
format from the pull-down list. 2 In the list on the left, select the target parallel output
port to set.
5 Press the [Frequency] button and select a frequency The number for a parallel output port is displayed in
from the pull-down list. “board (1 to 3)-number (1 to 16)” format (for example,
“1-3”).
6 Press the [OETF] button and select an OETF from the
pull-down list.
Note
7 Press the [Color] button and select a color space from Ports on boards 2 and 3 can be used when an
the pull-down list. XKS-G1700 Legacy Interface Board (option) is
installed.
333
To set action preferences
Setting a GPI Output You can set the timing, pulse width, and register to recall
by the action for a GPI output.
You can configure the trigger type and action for each GPI
1 Select the target GPI output to set.
output.
2 Press the [Action Details] button for [Reg/Timing/
GPI output via a network Pulse Width].
On GPI outputs via a network, GPI control is performed
The [Action Details] window appears.
using serial tally protocol commands.
GPI outputs can be configured in the same way as parallel
output ports.
3 Set the action preferences.
When a register recall action is selected
Note Press the [Register No.] button and enter a register
number in the numeric keypad window.
This uses a serial tally port, hence the network port must
be configured for a serial tally port. When [Rising Edge]/[Falling Edge]/[Any Edge]
trigger type is selected
For details, see “Setting a Serial Tally” (page 345). Press the [Timing] button and select a timing (Field1,
Field2, Any) from the pull-down list.
1 Open the Home > Setup > External Device > GPI
Output Assign menu (19105.41). When [Rising Edge]/[Falling Edge] trigger type is
selected
2 Select the target GPI output to set. Press the [Pulse Width] button and enter a pulse width
(fields) in the numeric keypad window.
3 Press the [Source Target] button and select a control
panel (Panel 1, Panel 2) to handle the GPI output from 4 Press [OK].
the pull-down list.
Trigger type and actions list 1)
When the trigger type is other than [Status]:
4 Press the [Trigger Type] button and select a trigger
P/P Keyx SS Recall, M/E-x Keyx SS Recall, No Action
type from the pull-down list.
When the trigger type is [Status]:
Rising Edge: Trigger causes the output to go high P/P Keyx SS Recall, M/E-x Keyx SS Recall, No Action
level and holds this state for the pulse width P/P Keyx On, M/E-x Keyx On
duration. Error Make, Error Break, Keep Make, Keep Break, Device
Falling Edge: Trigger causes the output to go low Recording
level and holds this state for the pulse width 1) “M/E-x” is M/E-1 to M/E-5
duration. ”Keyx” is Key1 to Key8”
Any Edge: When a trigger occurs, the output toggles
between high level and low level. Testing trigger output
Status: The output toggles between high level and low
You can output a test trigger from a GPI output port.
level according to the status.
NOP (No Operation): The trigger has no effect on the
output level. Note
A trigger is not output when the trigger type is [Status].
5 Press the [Edit Action] button for [Action].
The [GPI Output Assign] window appears. 1 Open the Home > Setup > External Device > GPI
Output Assign menu (19105.41).
6 Select an action to set.
2 Select the target GPI output to set.
Select a tab to change the action type to display.
[PP/ME Key SS Recall] tab: Key snapshot actions 3 Press the [Test Fire] button.
[PP/ME Key On] tab: Key on actions
[Make/Break/Device] tab: Error and device actions
Set the button for the target action to the on state.
7 Press [OK].
334
5 Press [OK].
Setting the Connection 6 Press the [Name] button and enter a port name (up to
Port of External Devices 16 characters) using the keyboard.
335
3 In the [TC Source] group, select a timecode source
(reference number for determining the tape position). Setting a Disk Recorder (VDCP)
LTC: Use LTC (Longitudinal Time Code). 1 Open the Home > Setup > External Device > Serial/
When interpolation data is returned from a VTR, Net Port Setting > DDR VDCP menu (19105.63).
use that interpolation data.
LTC:VITC: Normally use LTC, except when the tape A list of ports is shown on the left and the settings
is moving at speeds at which LTC cannot be read, status of the selected port is shown on the right.
use VITC.
When interpolation data is returned from a VTR, 2 In the list on the left, select the target port to set.
use that interpolation data.
VITC: Use VITC (Vertical Interval Time Code). 3 In the [DDR Type] group, select a type of disk
CTL: Use CTL (Control) pulse or timer counter pulse. recorder.
Use this only for a tape on which no timecode is
Player: Player
recorded.
Recorder: Recorder
4 In the list on the right, set the VTR constants of the
4 In the [Name Mode] group, select a file name mode.
item.
Fixed 8 Character: 8-character file name
Press the [Setting] button for an item to set and enter a
Variable Length: Variable-length file name (up to 23
VTR constant (00 to FF) in the numeric keypad
characters)
window.
Item Item description 5 In the [Frame Control Mode] group, select a frame
control mode.
VTR Constant HI-BYTE (DEVICE TYPE)
Block1 Byte1
For a disk recorder that does not support a timecode
VTR Constant LO-BYTE (DEVICE TYPE) with a drop frame bit, set drop frame mode or non drop
Block1 Byte2 frame mode.
VTR Constant HI-BYTE (FRAME) (PREROLL TIME) Drop Frame: Drop frame mode
Block1 Byte3 Non Drop Frame: Non-drop frame mode
VTR Constant LO-BYTE (FRAME) (PREROLL TIME)
Block1 Byte4
Notes
VTR Constant EDIT DELAY (FRAME)
Block1 Byte5 • Configurable only when the system signal format
frequency is 59.94.
VTR Constant EE DELAY (FRAME)
Block1 Byte6 • If the drop frame bit of the timecode is set, it
operates in drop frame mode.
VTR Constant OVER RUN (FRAME)
Block1 Byte7
VTR Constant TRAJECTORY
6 In the [TC Sense] group, select a timecode sense
mode.
Block1 Byte8
VTR Constant TC READ DELAY (FRAME) Zero based: Timecode sense (detection), taking the
Block2 Byte1 first frame of the loaded file as 00:00:00:00.
VTR Constant START DELAY (FRAME) SOM based: Sense (detection) occurs using the
Block2 Byte2 timecode recorded in the loaded file.
VTR Constant AFTER SYNC DELAY –
Block2 Byte3 7 Enable/disable duration detection using the [Duration
VTR Constant AFTER SYNC DELAY + Sense] button.
Block2 Byte4
On: Enable duration sense (detection).
VTR Constant MODE1 Off: Disable duration sense (detection).
Block2 Byte5
VTR Constant
Block2 Byte6
MODE2 8 In the list on the right, set the video port and response
speed of the item.
VTR Constant MAX PRRL SPEED
Block2 Byte7 Press the [Setting] button for an item to set and enter a
VTR Constant QUICK PVW PRRL TIME (FRAME) setting in the numeric keypad window.
Block2 Byte8
336
3 In the [TC Sense] group, select a timecode sense
Item Item description mode.
Video Port Number of the video port associated
with the target port to set Zero based: Timecode sense (detection), taking the
• Output port setting for a player first frame of the loaded file as 00:00:00:00.
• Input port setting for a recorder SOM based: Sense (detection) occurs using the
Maximum Maximum time required to open a file timecode recorded in the loaded file.
Open Delay
Maximum Maximum time required to cueup a file 4 In the list on the right, set the response speed of the
Cueup Delay item.
Play After Delay time after cueup until playback Press the [Setting] button for an item to set and enter a
Cueup Delay starts
setting in the numeric keypad window.
Stop Delay Delay time from issuing the Stop
command until playback stops Item Item description
Still Delay Delay time from issuing the Still Maximum Maximum time required to open a file
command until playback stops Open Delay
Continue Delay Delay time from issuing the Continue Maximum Maximum time required to cueup a file
command until playback stops Cueup Delay
Idle Delay Time from when file unload is Play After Delay time after cueup until playback
executed until idle state occurs. Cueup Delay starts
The idle state is a state wherein a
previous file has been unloaded before Stop Delay Delay time from issuing the Stop
a new file is loaded (state where no file command until playback stops
has been loaded). Still Delay Delay time from issuing the Still
Status Sense Time until the next Status Sense command until playback stops
Interval command is issued Command Delay time from issuing the Auto
Internal Reserved for future use. Delay (Auto Mode On/Off command until the
Parameter (1) Set the value to “255”. Mode) command takes effect
to (10) Command Delay time from issuing the Out Preset
Delay (Out command until the command takes
Preset) effect
Setting loop/recue
Command Delay time from issuing the Preview In
You can enable/disable looping and recueing. Delay (Preview Preset command until the command
In Preset) takes effect
1 Open the Home > Setup > External Device > Serial/ Internal Reserved for future use.
Net Port Setting > DDR VDCP menu (19105.63). Parameter (1) Set the value to “255”.
to (4)
2 Enable/disable looping using the [Loop] button.
On: Enable looping. Replay the loaded file in a
continuous loop.
Setting an AMP Compatible Device
Off: Disable looping.
1 Open the Home > Setup > External Device > Serial/
3 Enable/disable recueing using the [Recue] button. Net Port Setting > AMP menu (19105.65).
On: Enable recueing. After playing the loaded file, A list of ports is shown on the left and the settings
recue the beginning and then stop. status of the selected port is shown on the right.
Off: Disable recueing.
2 In the list on the left, select the target port to set.
1 Open the Home > Setup > External Device > Serial/ 4 Press the [TCP/IP Port] button and enter a port number
Net Port Setting > DDR Odetics menu (19105.64). in the numeric keypad window.
A list of ports is shown on the left and the settings
status of the selected port is shown on the right.
5 In the [TC Sense] group, select a timecode sense
mode.
2 In the list on the left, select the target port to set.
337
Zero based: Timecode sense (detection), taking the
first frame of the loaded file as 00:00:00:00. Item Item description
SOM based: Sense (detection) occurs using the Internal Reserved for future use.
timecode recorded in the loaded file. Parameter (1) Set the value to “255”.
to (10)
6 In the list on the right, set the video port and response
speed of the item.
Press the [Setting] button for an item to set and enter a
setting in the numeric keypad window.
338
Router/Tally Setup
1 Open the Home > Setup > Router/Tally > NS-Bus >
Matrix menu (19106.11).
The settings status of the switcher and external boxes
is displayed.
1 Open the Home > Setup > Router/Tally > NS-Bus >
Matrix menu (19106.11).
The settings status of the switcher and external boxes
is displayed.
339
3 Press the [Matrix Size] button and select a size from External boxes 1 and 2 become coupled and can be
the pull-down list. used as an external box with 12 inputs (4 + 8).
- - -: Do not use.
4×1: 4 inputs, 1 output
8×1: 8 inputs, 1 output Selecting an Alias Name Group
16×1: 16 inputs, 1 output
You can select an NS-Bus alias name group.
Note 1 Open the Home > Setup > Router/Tally > NS-Bus >
The maximum number of inputs for all external boxes Matrix menu (19106.11).
is 18.
2 Press the [Alias Name Group No.] button and select a
4 Press the [Source] button and enter an address for the group number (1 to 8) from the pull-down list.
first source in the numeric keypad window.
1 Open the Home > Setup > Router/Tally > NS-Bus >
Matrix menu (19106.11).
340
Setting a Tally Group Setting Wiring
You can select a tally group (1 to 8) controlled using NS- You can set output and input connection information
Bus. You can set multiple tally groups. (wiring) in NS-Bus space.
The wiring settings are common to both parallel tally and
1 Open the Home > Setup > Router/Tally > Tally > serial tally.
Group Tally menu (19106.21).
1 Open the Home > Setup > Router/Tally > Tally >
2 In the [Tally Group] group, select a tally group (Group Wiring menu (19106.22).
1 to Group 8).
2 Select the target wiring to set.
3 Enable/disable the tally using the [NS-Bus Tally
Enable] button. To select and set multiple wiring, place a check mark
beside the target wiring to set.
On: Enable tally control using NS-Bus. You can also press the [Select Number(s)] button and
Off: Disable tally control using NS-Bus. enter a wiring number in the numeric keypad window.
Note
The maximum number of wiring settings that can be
set at the same time is 128.
Note
If multiple consecutive wiring settings are selected,
consecutive addresses from the entered address are set.
Note
If multiple consecutive wiring settings are selected,
consecutive addresses from the entered address are set.
341
The number for a parallel input port is displayed in
Setting Tally Generation “board (1 to 3)-number (1 to 6)” format (for example,
“1-3”).
You can set the reference destination and tally type for Note
tally generation. Ports on boards 2 and 3 can be used when an
The tally generation settings are common to both parallel XKS-G1700 Legacy Interface Board (option) is
tally and serial tally. installed.
1 Open the Home > Setup > Router/Tally > Tally > Tally 3 Press [OK].
Enable menu (19106.23).
To delete a tally generation setting
2 Select the target tally to set. Select the target tally to delete and press the [Delete]
button.
To select and set multiple tallies, place a check mark
beside the target tallies to set.
To select and set all tallies, place a check mark in the
Select All checkbox.
You can also press the [Select Number(s)] button and
enter a tally number in the numeric keypad window.
7 Press [OK].
1 Select the target tally to set and press the [Edit] button
for [Tally Input].
The [Select Tally Input] window appears.
2 Set the button for the target parallel input port to the on
state.
342
Setting Advanced Tally Setting Tally Copy
You can use cross-point delay in combination with the You can copy the tally information for a particular source
advanced tally function to output a tally prior to the actual to a different source.
switching of the cross-point. The tally copy settings are common to both parallel tally
When the cross-point delay is configured and advanced and serial tally.
tally is enabled, a tally is output when a cross-point is
selected and then the cross-point switches after the delay 1 Open the Home > Setup > Router/Tally > Tally > Tally
has expired. When advanced tally is disabled, the tally is Copy menu (19106.25).
output in conjunction with cross-point switching.
Advanced tally can be set for each tally type (R1 to R8, G1 2 Select the target tally copy to set.
to G8, Y1 to Y8).
To select and set multiple tally copies, place a check
mark beside the target tally copies to set.
Notes
You can also press the [Select Number(s)] button and
• When cross-points are the target of multiple tally types enter a tally copy number in the numeric keypad
and the advanced tally setting (enable/disable) varies window.
depending on the tally type, cross-point tallies are output
with advanced tally enabled. Note
• When a cross-point with cross-point delay and advanced
tally enabled is selected, both the target cross-point The maximum number of tally copy settings that can
tallies from before and after cross-point selection are be set at the same time is 128.
output during the delay period before the cross-point
switches. 3 Press the [Copy From] button and enter a source
address for a copy source in the numeric keypad
1 Open the Home > Setup > Router/Tally > Tally > window.
Advanced Tally menu (19106.24).
Note
2 In the [Advanced Tally Mode] group, select a tally If multiple consecutive tally copy settings are selected,
type. consecutive addresses from the entered address are set.
R1 to R8: Tally type 1 to 8 for red tally
G1 to G8: Tally type 1 to 8 for green tally 4 Press the [Copy To] button and enter a source address
Y1 to Y8: Tally type 1 to 8 for yellow tally for a copy destination in the numeric keypad window.
Set the button for the tally type for which to enable
advanced tally to the on state. You can select multiple Note
tally types.
If multiple consecutive tally copy settings are selected,
consecutive addresses from the entered address are set.
To delete a tally copy setting
Select the target tally copy to delete and press the [Delete]
button.
343
3 Press the [Level] button and enter a level (1 to 8) in the
Setting a Parallel Tally numeric keypad window.
1 Open the Home > Setup > Router/Tally > Tally > 5 Set the button for the target tally to the on state.
Parallel Tally menu (19106.26).
R1 to R8: Tally type 1 to 8 for red tally
2 Select the target parallel output port to set. G1 to G8: Tally type 1 to 8 for green tally
Y1 to Y8: Tally type 1 to 8 for yellow tally
To select and set multiple ports, place a check mark
beside the target ports to set. 6 Press [OK].
To select and set all ports, place a check mark in the
Select All checkbox. To delete a parallel tally setting
You can also press the [Select Number(s)] button and Select the target parallel tally to delete and press the
enter a port number in the numeric keypad window. [Clear] button.
Note
Ports on boards 2 and 3 can be used when an
XKS-G1700 Legacy Interface Board (option) is
installed.
5 Press [OK].
To set a destination tally
344
Setting a source address
Setting a Serial Tally You can set a source address for each bit number.
1 Open the Home > Setup > Router/Tally > Tally >
You can set the output port for a serial tally. Two ports Serial Tally menu (19106.27).
(serial tally ports 1 and 2) can be used.
You can specify a port number for a network connection to 2 Display the target serial tally port to set.
control tally information via a network.
Select a tab to change the port to display.
[Port 1] tab: Serial tally port 1
Note
[Port 2] tab: Serial tally port 2
To use serial tally ports 1 and 2, serial tallies must be
assigned to serial ports in the Home > Setup > External 3 Select the target bit number to set.
Device > Serial/Net Port Assign menu (19105.51).
To select and set multiple bit numbers, place a check
mark beside the target bit numbers to set.
For details about setting a serial port, see “Setting the
To select and set all bit numbers, place a check mark
Connection Port” (page 335).
in the Select All checkbox.
You can also press the [Select Number(s)] button and
1 Open the Home > Setup > Router/Tally > Tally >
enter a bit number in the numeric keypad window.
Serial Tally menu (19106.27).
6 Press [OK].
To set a network port
You can set the port number of a network port.
Press the [TCP/IP Port] button and enter a port number in
the numeric keypad window.
Note
Correct operation may not occur, depending on the port.
For a serial tally network port, port number “2020” is
recommended for [Port 1], and “2021” is recommended
for [Port 2]. For details, consult your Sony service or sales
representative.
345
Link Setup Chapter 27
The link function is enabled at the same time you move
Setting a Cross-Point the fader lever.
346
The [Assign V/K Pair] window appears.
Select a tab to change the V/K pair number to display. 1 Open the Home > Setup > Link > M/E Link menu
(19107.21).
7 Press [OK].
To return a link table to the initial settings
2 Select the target link number to set.
Press the [Initialize Table] button, check the message, then To select and set multiple link numbers, place a check
press [OK]. mark beside the target link numbers to set.
To select and set all link numbers, place a check mark
in the Select All checkbox.
347
1 Open the Home > Setup > Link > Key Transition Link
Setting a Key Link > Link in Multi M/Es menu (19107.32).
On: Enable link. 7 Press the [Edit] button for [Linked Key].
Off: Disable link. The [Assign Linked Key] window appears.
5 Press the [Edit] button for [Linked Key]. 8 Set the button for the link destination key to the on
The [Linked Key] window appears. state.
7 Press [OK].
To link the key selection of a next transition
Set the [Next Trans. Link] button to the on state.
The keys are linked and the next transition selection
buttons in the transition control block are selected.
Example:
When key 2 and key 3 are linked to key 1:
When key 1 is selected in a next transition, key 2 and key
3 are also selected.
Note
The link setting of the next transition selection buttons is
common to all switcher banks.
348
Setting a Color Corrector Setting a Bus and
Link Group Destination Link
You can configure an AUX bus color corrector link group. You can link a switcher bus with a router destination.
1 Open the Home > Setup > Link > Aux Bus CCR Link
menu (19107.41). Setting a Matrix
2 Select the target AUX bus to set. You can set the first source address, first destination
address, and level of a matrix to set in NS-Bus space.
To select and set multiple AUX buses, place a check
You can set up to 8 types of matrix.
mark beside the target AUX buses to set.
To select and set all AUX buses, place a check mark in
the Select All checkbox.
1 Open the Home > Setup > Link > External Bus Link >
Matrix Settings menu (19107.51).
3 Press the [Link Group] button and select a group (Link
2 Select the target matrix to set.
1 to Link 12) from the pull-down list.
AUX buses configured in the same group form a link 3 Press the [Source] button and enter a source address in
group. the numeric keypad window.
Setting a Bus
You can select a matrix and link a switcher bus with a
router destination.
1 Open the Home > Setup > Link > External Bus Link >
Bus/Destination Assign menu (19107.52).
4 Set the button for the link source bus to the on state.
Select a tab to change the bus to display.
[M/E-1 to M/E-5] tab: M/E bus
[P/P] tab: P/P bus
[Aux] tab: AUX bus
[FM/DME Util] tab: Frame memory/DME bus
5 Press [OK].
349
6 Press the [Matrix No.] button and select a matrix (1 to
8) to set from the pull-down list.
1 Open the Home > Setup > Link > External Bus Link >
Table Source Assign menu (19107.53).
350
Maintenance Chapter
351
Log Information
1 Open the Home > Maintenance > Log > Export menu
(19202.11).
352
System Configuration
and Management
Note
Switcher settings cannot be changed.
The switcher is set to unit ID1 (fixed). The host name of
the switcher is set in the System Configuration > Network
> Network Settings menu (20201.11).
353
5 Press the [Edit] button for [IPv4 Address/Prefix,
Default Gateway].
Setting a Network AUX
The [Edit Network] window appears.
Remote Panel
6 Press the [Address] button for [IPv4] and enter an
address using the keyboard.
Network AUX remote panel
7 Press the [Default Gateway] button for [IPv4] and A network AUX remote panel is a function that provides a
enter a default gateway address using the keyboard. simple connection of an MKS-R3210/R1620 Remote
Control Panel with a switcher, without using LSM (Live
8 Press [OK]. System Manager), for using the MKS-R3210/R1620 as a
switcher remote panel. You can control the switching of
9 Press the [Apply] button. cross-points on the switcher from a remote panel on the
network.
To return to the previous setting
Press the [Clear] button, check the message, then press Network AUX remote panel restrictions
[OK]. • Up to 16 remote panels can be configured for a single
control panel.
10 Check the message, then press [OK]. • The network AUX remote panel function is not available
if the MKS-R3210/R1620 Remote Control Panel is
To identify a control panel connected to LSM.
Select the target control panel to set and press the [Send • The network AUX remote panel function is not available
Beacon] button. if control using the NS-Bus External Control protocol is
The buttons on the control panel start flashing to identify enabled.
the target control panel to set. • The following function and settings restrictions apply to
a remote panel.
Item Restrictions
Functions The following functions are
not available.
• Global salvo
• Protect
• Monitor
• Retrace
• Linkage
Levels Only 1 to 8 are available.
Operation button colors Set to “Local”
(Color Settings on the
Display Settings page)
Source/destination names Source names set on the
switcher, and fixed bus
names
Alias name selection not
supported
(Alias Name Lists page)
354
For details about connection, refer to the ICP-X1224/ To display the latest status
X1124/X1216/X1116 Installation Manual. Press [Refresh].
Note
All the connected remote panels are rebooted.
355
Configuring a System Setting Startup
Controller
Setting an SSD Area
Configuring NS-Bus The switcher has two SSD areas (SSD-A, SSD-B), and you
can select either as the SSD area to use at startup.
You can also copy the data in the SSD area currently being
Enabling the NS-Bus External Control used to the other SSD area as a backup.
protocol If a fault occurs after a software upgrade, for example, you
You can enable NS-Bus External Control protocol control could reboot the switcher using the backup data SSD area
(A) or (B). to restore the state prior to the upgrade.
1 Open the System Configuration > Configuration > Selecting the SSD area to use at startup
System Controller menu (20101.31).
Setting the UUID of the switcher The switcher system must be rebooted for the settings
to take effect.
You can generate a switcher UUID when the NS-Bus
External Control protocol control is enabled.
Copying an SSD area
1 Open the System Configuration > Configuration > You can copy the data in the SSD area currently being used
System Controller menu (20101.31). to the other SSD area.
2 Press the [Generate] button in the [Switcher UUID] 1 Open the System Configuration > Configuration >
group. Start Up menu (20101.61).
3 Check the message, then press [OK]. The version, creation date and time, and a memo are
displayed for SSD-A and SSD-B. A check mark is
A UUID is generated and displayed in the [Switcher displayed in [Current] for the SSD area currently in
UUID] group. use.
When a UUID is generated, the display changes to the
new UUID. 2 Press the [Start Up Device Copy] button.
356
Configuring Network The switcher LAN connector and configurable LAN types
supported by each network interface are shown below.
Settings Network I/F Configurable LAN Connector a)
STD 1 • Control LAN (Ctrl LAN) f
STD 2 • Utility LAN 1 (Util LAN 1) g
Setting the Host Name of the • No setting (Off)
Switcher OPT 1 • For control LAN redundancy r
(Ctrl LAN Redundant)
• No setting (Off)
Note
OPT 2 • Utility LAN 2 (Util LAN 2) q
The host name setting is linked to the system name setting • For utility LAN 1 redundancy
in the System Configuration > SNMP > Common menu (Util LAN 1 Redundant)
(20701.11). • No setting (Off)
OPT 3 • User LAN 1 (User LAN 1) p
1 Open the System Configuration > Network > Network • No setting (Off)
Settings menu (20201.11). OPT 4 • User LAN 2 (User LAN 2) o
• For user LAN 1 redundancy
2 Press the [Hostname] button and enter a host name (up (User LAN 1 Redundant)
to 63 characters) using the keyboard. • No setting (Off)
3 Press [OK]. a) Number corresponding to the description of parts on the rear of the
switcher.
To return to the previous setting 1 Open the System Configuration > Network > Network
Press the [Clear] button, check the message, then press Settings menu (20201.11).
[OK].
2 Select [STD1].
5 Check the message, then press [OK].
3 Press the [Edit] button.
Setting the Network Interface The [Standard Network I/F 1 Settings] window
appears.
You can configure the following six types of network
interface. Note
• Standard interface 1 (STD 1):
The standard interface addresses can only be set
LAN 1 connector (f (see page 28) on rear of switcher)
manually.
settings
• Standard interface 2 (STD 2):
LAN 2 connector (g (see page 28) on rear of switcher)
4 Press the [Address] button for [IPv4] and enter an
address using the keyboard.
settings
• Expansion interface 1 (OPT 1):
Network expansion 1 connector 1) (r (see page 29) on
5 Press the [Prefix Length] button for [IPv4] and enter a
prefix length in the numeric keypad window.
rear of switcher) settings
• Expansion interface 2 (OPT 2):
Network expansion 2 connector 1) (q (see page 29) on
6 Press [OK].
rear of switcher) settings
• Expansion interface 3 (OPT 3):
7 Press the [Apply] button.
Network expansion 3 connector 1) (p (see page 29) on To return to the previous setting
rear of switcher) settings Press the [Clear] button, check the message, then press
• Expansion interface 4 (OPT 4): [OK].
Network expansion 4 connector 1) (o (see page 29) on
rear of switcher) settings 8 Check the message, then press [OK].
1) Can be used when a network card is installed in the PCIe slot of the
switcher.
357
To set an interface other than standard interface To return to the previous setting
1 (STD 1) Press the [Clear] button, check the message, then press
[OK].
1 Open the System Configuration > Network > Network
Settings menu (20201.11). 13 Check the message, then press [OK].
2 Select the target network interface to set.
Setting the Default Gateway
3 Press the [Edit] button.
A setup window for the selected network interface 1 Open the System Configuration > Network > Network
appears. Settings menu (20201.11).
4 Press the [LAN] button and select a LAN to set from 2 Press the [Edit] button in the [Default Gateway] group.
the pull-down list.
The [Default Gateway] window appears.
The types of LAN which can be set will vary
depending on the selected network interface. 3 Press the [LAN] button for [IPv4] and select the target
LAN to set from the pull-down list.
When a LAN for redundancy is selected
The same settings as the main LAN are applied. Select [Ctrl LAN], [Util LAN1], [Util LAN2], [User
Proceed to step 11. LAN1], or [User LAN2].
When not using the IPv4 default gateway, select [No
5 Press the [Mode] button for [IPv4] and select a setup Assign].
mode from the pull-down list. The [Mode] setting for [IPv4] is linked to the selected
LAN setting. When set to [Off] or [DHCP], proceed to
Off: Do not use IPv4. step 5.
Manual: Set manually.
DHCP: Set automatically using DHCP. 4 Press the [Address] button for [IPv4] and enter an
When [Off] or [DHCP] is selected, proceed to step 8. address using the keyboard.
6 Press the [Address] button for [IPv4] and enter an 5 Press the [LAN] button for [IPv6] and select the target
address using the keyboard. LAN to set from the pull-down list.
7 Press the [Prefix Length] button for [IPv4] and enter a Select [Util LAN1], [Util LAN2], [User LAN1], or
prefix length in the numeric keypad window. [User LAN2].
When not using the IPv6 default gateway, select [No
8 Press the [Mode] button for [IPv6] and select a setup Assign].
mode from the pull-down list. The [Mode] setting for [IPv6] is linked to the selected
LAN setting. When set to [Off], [Auto], or [DHCP],
Off: Do not use IPv6. proceed to step 7.
Manual: Set manually.
Auto: Set automatically using RA (Router 6 Press the [Address] button for [IPv6] and enter an
Advertisement). address using the keyboard.
DHCP: Set automatically using DHCP.
When [Off], [Auto], or [DHCP] is selected, proceed to 7 Press [OK].
step 11.
8 Press the [Apply] button.
9 Press the [Address] button for [IPv6] and enter an
address using the keyboard. To return to the previous setting
Press the [Clear] button, check the message, then press
10 Press the [Prefix Length] button for [IPv6] and enter a [OK].
prefix length in the numeric keypad window.
9 Check the message, then press [OK].
11 Press [OK].
12 Press the [Apply] button.
358
Setting the DNS Server
Setting the Date and Time
1 Open the System Configuration > Network > Network
Settings menu (20201.11).
Setting the Time Zone
2 Press the [Edit] button in the [DNS Server] group.
The [DNS Server] window appears. 1 Open the System Configuration > Date/Time > Date/
Time Settings menu (20301.11).
3 Press the [Mode] button and select a setup mode from
the pull-down list. 2 Press the [Change] button in the [Timezone] group.
Note
Setting the Date/Time
If there is no LAN with network interface setup mode
set to DHCP, [DHCP] cannot be selected.
Setting automatically (syncing to NTP
4 Select a LAN for obtaining DNS in [LAN]. server)
Press the button on the left and select a LAN from the You can set the date and time automatically by syncing to
pull-down list, then press the button on the right and an NTP server.
select IPv4 or IPv6 from the pull-down list.
Proceed to step 7. 1 Open the System Configuration > Date/Time > Date/
Time Settings menu (20301.11).
Note
2 Press the [Server 1] button and enter an IP address or
LANs that are set to a network interface setup mode domain name for NTP server 1 using the keyboard.
other than DHCP cannot be selected.
You can enter an IPv4 address, IPv6 address, or an
5 Press the [Domain Name] button and enter a domain FQDN (fully qualified domain name).
name using the keyboard.
3 Set NTP server 2/NTP server 3 using the [Server 2]
6 Press a [Server 1] to [Server 4] button and enter a button/[Server 3] button as required.
server address using the keyboard.
4 Press the [Synchronize Now] button in the
Enter an IPv4 address or IPv6 address. [Synchronization] group.
359
Enter values in the order year (YYYY), month (MM),
day (DD), hour (hh), minute (mm), and second (ss).
Firmware Version
4 Press [Enter]. Management and
Setting the switcher to act as an NTP Installation
server
When the switcher is configured to act as an NTP server,
an external device connected to the switcher can access the Displaying Package Status
NTP server.
You can check information about the installed packages in
1 Open the System Configuration > Date/Time > Date/ the System Configuration > Version > Info/Install menu
(20401.11).
Time Settings menu (20301.11).
Current System Version: Installed package version
2 Set the [NTP Service for Ext Dev] button to the on Status: Version status within a package
“OK” is displayed if there is no mismatch.
state.
“ Incorrect Version” is displayed if there is a
To deny access, set the [NTP Service for Ext Dev] mismatch.
button to the off state. The following information is displayed for each switcher/
control panel.
Select a tab to change the switcher (Switcher)/control
panel 1 (Panel 1)/control panel 2 (Panel 2) display.
Module: Name of module within the switcher/control
panel
Version: Version of module
Date/Time: Modification date and time of module
The display of modification date and time may not be
supported depending on the module.
Installing a Package
Note
Installing a package
360
3 Select a package file to install.
The file name, modification date and time, and size of Managing and Installing
the selected package are displayed in [Install System
Version]. Licenses
To delete a package file
Press the [×] button on the right of the package row. You can install the following licenses.
Note
Administrator privileges are required to install/uninstall
licenses and to export unique device IDs.
Installing/Uninstalling a License
Installing a license
You can select a license key and install a license.
361
Note
1 Open the System Configuration > License > Manage Displaying a user account
Licenses menu (20501.11). You can check information about user accounts in the
System Configuration > User Account > Manage Users
2 Press the [Export UDID] button. menu (20601.11).
A computer folder selection dialog appears. Current User: Name of the currently signed-in user
Username: Name of registered users
3 Select a folder and save the device information file. Group: Name of group to which user belongs
No of Included Groups: Number of additional groups to
which a user belongs if belonging to more than one
group (excludes the displayed group)
362
4 Press the [Set Password] button and enter a password 2 Select the target user to edit.
(8 to 32 characters) using the keyboard.
3 Press the [Change Password] button.
The password must contain at least one single-byte
alphabetic character and at least one single-byte The [Change Password] window appears.
numeric character.
4 Press the [Input New Password] button and enter a
5 Press the [Confirm Password] button and enter the password (8 to 32 characters) using the keyboard.
same password using the keyboard.
The password must contain at least one single-byte
6 Select a group to which the user will belong using alphabetic character and at least one single-byte
[Select Groups]. numeric character.
Place a check mark for groups to which to belong. 5 Press the [Confirm Password] button and enter the
To select all groups, place a check mark in the Select same password using the keyboard.
All checkbox.
6 Press [OK].
7 Press [OK].
Changing the groups for a user account
Deleting a user account
1 Open the System Configuration > User Account >
1 Open the System Configuration > User Account > Manage Users menu (20601.11).
Manage Users menu (20601.11).
2 Select the target user to edit.
2 Select the target user to delete.
3 Press the [Select Groups] button.
3 Press the [Delete User] button.
The [Select Groups] window appears.
4 Check the message, then press [OK].
4 Select a group to which the user will belong using
[Select Groups].
Renaming a user account
Place a check mark for groups to which to belong.
1 Open the System Configuration > User Account > To select all groups, place a check mark in the Select
Manage Users menu (20601.11). All checkbox.
363
Displaying a group
You can check information about groups in the System Configuring SNMP
Configuration > User Account > Manage Groups menu
(20601.21).
Current User: Name of the currently signed-in user
Group Name: Names of the registered groups Enabling/Disabling SNMP
No. of Users: Number of users belonging to a group
1 Open the System Configuration > SNMP > Common
menu (20701.11).
Creating a group
You can create up to 15 groups, not counting the default 2 Enable/disable SNMP using the [Enable] button for
groups. [SNMP Mode].
1 Open the System Configuration > User Account > On: Enable SNMP.
Manage Groups menu (20601.21). Off: Disable SNMP.
When disabled, proceed to step 4.
2 Press the [Add Group] button.
3 Set whether to send a trap when authentication fails
The [Add Group] window appears. using the [Auth Trap] button.
3 Press the [Input Group Name] button and enter a group On: Send trap when SNMP authentication fails.
name (up to 32 characters) using the keyboard. Off: Do not send trap when SNMP authentication
fails.
The valid characters for group names are single-byte
alphanumeric characters and periods. 4 Press the [Apply] button.
Renaming a group 2 Press the [System Name] button for [MIB-2 System
Variables] and enter a system name using the
1 Open the System Configuration > User Account > keyboard.
Manage Groups menu (20601.21).
Note
2 Select the target group to rename.
The system name setting is linked to the host name
setting in the System Configuration > Network >
3 Press the [Edit Group Name] button.
Network Settings menu (20201.11).
The [Edit Group Name] window appears.
3 Press the [System Contact] button for [MIB-2 System
4 Press the [Input Group Name] button and enter a group Variables] and enter the administrator information (up
name (up to 32 characters) using the keyboard. to 255 characters) using the keyboard.
The valid characters for group names are single-byte 4 Press the [System Location] button for [MIB-2 System
alphanumeric characters and periods. Variables] and enter the system location information
(up to 255 characters) using the keyboard.
5 Press [OK].
364
5 Press the [Apply] button. Configuring a host
To return to the previous setting
Press the [Clear] button, check the message, then press
1 Open the System Configuration > SNMP > SNMP v1/
v2c > Hosts menu (20701.22).
[OK].
Setting a community
3 Press an [IP Address 1] to [IP Address 3] button for
[SNMP v1/v2c Trap Hosts] and enter a destination
SNMP manager to send traps using the keyboard.
Note
You can enter an IPv4 address, IPv6 address, or FQDN
The following community names are set by default. (fully qualified domain name) for the SNMP manager.
To prevent security risks, we recommend changing the
community names from the default values. 4 Press the [Apply] button.
Read-Only Community: public
Read-Write Community: private To return to the previous setting
Trap Community: unknown Press the [Clear] button, check the message, then press
[OK].
1 Open the System Configuration > SNMP > SNMP v1/
v2c > Community menu (20701.21). 5 Check the message, then press [OK].
365
Appendix
Standard wipes
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24
Enhanced wipes
Rotary wipes
100 101 102 103 104 105 106 107 150 151
156 158 160 162 516 518 604 606 624 661
366
Mosaic wipes
200 201 202 203 206 207 208 209 210 211
212 213 220 221 222 223 224 225 226 227
228 229 230 231 232 233 234 235 236 237
238 239 240 241 242 243 244 245 246 247
250 251 252 253 254 255 256 257 260 261
Squeeze
1021 1022 1023 1024 1025 1026 1027 1028 1029 1030
367
Split
Door
Flip tumble
1101 1102
Page turn
1301 1302 1303 1304 1305 1306 1307 1308 1309 1310
1311 1312 1313 1315 1316 1317 1318 1341 1342 1343
1344 1345
Roll
1321 1322 1323 1324 1325 1326 1327 1328 1329 1330
1331 1332 1333 1335 1336 1337 1338 1346 1347 1348
1349 1350
Frame in/out
1201 1202 1203 1204 1205 1206 1207 1208 1209 1221
368
Picture-in-picture
1251
Mosaic
1701
Defocus
1702
Squeeze
Page turn
2701 2702 2703 2704 2705 2706 2707 2708 2709 2710
2711 2712 2713 2715 2716 2717 2718 2741 2742 2743
2744 2745
369
Roll
2721 2722 2723 2724 2725 2726 2727 2728 2729 2730
2731 2732 2733 2735 2736 2737 2738 2746 2747 2748
2749 2750
Frame in/out
Picture-in-picture
2651 2652
Crop slide
2661 2662
Brick
3601
370
Squeeze
7021 7022 7023 7024 7025 7026 7027 7028 7029 7030
7031
Frame in/out
7201 7202 7203 7204 7205 7206 7207 7208 7221 7222
7223 7224
371
Menus Recalled by Pressing a Button Twice
The control panel has buttons that can display a menu Notes
when double-pressed.
When the following buttons are pressed twice in quick • Some button operations and menu settings may be
succession, the corresponding menu is displayed. disabled depending on the configuration of installed
“XX” represents the last recalled menu. options and connected control panels.
• Assignment may be required depending on the button.
For details about assigning buttons, see “Assigning
Control Panel Buttons” (page 317).
Cross-point control block
a) 1st row delegation buttons in key/AUX bus delegation mode and delegation buttons assigned to the function button section.
372
Button Menu recalled
[SUPER MIX] button Home > M/E-x > Bus/Transition > Transition > Transition Type
Home > M/E-x Sub > Bus/Transition > Transition > Transition Type
Home > P/P > Bus/Transition > Transition > Transition Type
Home > P/P Sub > Bus/Transition > Transition > Transition Type
(M/E-x = M/E-1 to M/E-5)
[PST COLOR MIX] button Home > M/E-x > Bus/Transition > Transition > Transition Type
Home > M/E-x Sub > Bus/Transition > Transition > Transition Type
Home > P/P > Bus/Transition > Transition > Transition Type
Home > P/P Sub > Bus/Transition > Transition > Transition Type
(M/E-x = M/E-1 to M/E-5)
[FM1&2 CLIP] to [FM15&16 CLIP] buttons Home > M/E-x > Bus/Transition > Transition > Clip Transition
Home > M/E-x Sub > Bus/Transition > Transition > Clip Transition
Home > P/P > Bus/Transition > Transition > Clip Transition
Home > P/P Sub > Bus/Transition > Transition > Clip Transition
(M/E-x = M/E-1 to M/E-5)
373
Button Menu recalled
[K1RSZ] to [K8RSZ] buttons Home > M/E-x > Keyx > Resizer/Proc Key > Resizer Adjust/DME
Select
Home > P/P > Keyx > Resizer/Proc Key > Resizer Adjust/DME Select
(M/E-x = M/E-1 to M/E-5, Keyx = Key1 to Key8)
374
Number of Switcher SL Key Restrictions
Resources
If the number of keys on a single switcher bank is four or
lower, SL keys are set as key 5 to key 8.
The number of resources that can be used will vary Only one switcher bank can use an SL key.
depending on the system signal format. To use the SL key function, the following options are
The maximum number of resources for 4K format (2160P) required.
and HD format (1080P, 1080i) are shown below. • XKS-G1600 GPU Pack
• XZS-G1620 SL Key License
Notes When the system signal format is 2160P, the SL key
function must be enabled for use.
• To use 4K formats, the XZS-G1500 4K Upgrade
License is required. For details about setting GPU functions, see “Setting a
• The DME function is not supported in version 1.0. GPU” (page 286).
Resource 4K HD
Switcher banks a)
1 2 Restrictions
When M/E split is enabled 2 4
Setting keys
b)
Keys 4 16 • Only Linear key type supported
Keys per switcher bank 4 8 However, the following settings are not supported.
Inputs 24 44 - [Filter] parameter
- Clean mode
Inputs configurable with a format 12 24
converter
- Key invert
- Key position
Inputs configurable with a color 6 – • Key edge not supported
corrector/HDR converter c)
• Mask not supported
Outputs 12 24 • Blink not supported
Outputs configurable with a format 6 12 • Processed Key not supported
converter • Video Process supported
Outputs configurable with a color 3 – However, the following settings are not supported.
corrector/HDR converter c) - [Hue Delay] parameter
DME channels d) 2 4 - [Black Level] parameter
DME channel 1 when enhanced 1 3
• For resizer, only two-dimensional transform movement
function mode is enabled ([Location X] parameter, [Location Y] parameter)
supported
DME channels 1 and 2 when enhanced – 2
function mode is enabled • Use of still image combined content for key fill/key
source
Frame memory output channels 6 16
- Selecting a signal using cross-point buttons not
Clip player output channels e)
2 4 supported
Multi viewers 1 2 - Color matte setting for key fill not supported
Color backgrounds 1 2 - Selecting self mode/auto select mode/split mode for
key source not supported
a) You can change the switcher bank (M/E-1 to M/E-5, P/P) assignment in • Key Priority supported
the Home > Setup > Switcher > Config > M/E Assign menu (19103.11).
b) If the number of keys on a single switcher bank is four or lower, SL keys
However, the following restrictions apply.
can be used. - SL keys (key 5 to key 8) assigned the priority of four
c) To use the HDR converter function, the XZS-G1750 HDR Converter keys as a single group
License is required.
d) To use the DME function, the XKS-G1600 GPU Pack and XZS-G1610 3D
- Within SL keys (key 5 to key 8), arbitrary priority
DME License are required. supported
For 4K formats, either DMEs or SL keys can be enabled.
e) To use the clip player function, the XKS-G1600 GPU Pack and Transitions
XZS-G1800 Clip Player License are required. • For transition type, only mix and cut supported
• Transition preview not supported
• Key priority change not supported, depending on the
transition
375
Switcher bank outputs
• Key preview output not supported
• For program output, SL keys supported
However, the following restrictions apply.
- SL keys (key 5 to key 8) assigned to program outputs
as a group
- In multi program 2 mode, SL key assignment on
PGM2 to PGM4 not supported
- In DSK mode, SL key assignment not supported
• Preview output supported
However, when the switcher bank operation mode is
standard mode, the preview output SL key has the same
image as the program output SL key during the
transition.
Copy and Swap
• Copy and swap settings data between normal keys and
SL keys supported
However, the settings for functions that cannot be used
on SL keys are reset to the default values.
376
Macro Events
The event type is determined by a symbol and the required For details about events, see “Events” (page 236) and
data for an event is set using parameters. “Editing a Macro Event” (page 243).
377
Event Symbol Continue
Rewind device/frame memory/clip player Rewind a
Fast forward device/frame memory/clip player FF a
Recall frame memory/clip player video content ClipRecall ×
Enable/disable frame memory/clip player audio Audio ×
Set frame memory/clip player loop FMLoop a
Recall utility function in cross-point control block KeyBusUtilButton ×
Record to VTR/disk recorder DeviceRecord a
Enable/disable AUX mix AuxMix ×
Delegation selection in cross-point button rows in free assign mode XptRowAssign ×
Output trigger test from GPI output port GPITestFire ×
Send command to TCP/IP connected external device NetworkMessaging a
Select cross-point assign table XptTableForRow a
Resume all paused macros in multi mode MacroTake ×
Stop all paused macros in multi mode MacroCancel ×
Move to previous keyframe PrevKF ×
Move to next keyframe NextKF ×
Set transition rate TransitionRate ×
378
Symbol Parameter Parameter setting values Description
MEAutoTransition ME ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
ME1Main&Sub to ME5Main&Sub,
PPMain&Sub
Time Current Transition rate (number of frames)
0 to 999 • “Current” = current value
ABusXpt Current Background A bus button number
1 to 300 • “Current” = currently selected button number
BBusXpt Current Background B bus button number
1 to 300 • “Current” = currently selected button number
MECut ME ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
ME1Main&Sub to ME5Main&Sub,
PPMain&Sub
KeyAutoTransition ME ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
ME1Main&Sub to ME5Main&Sub,
PPMain&Sub
Key Key1 to Key8 Key
Time Current Transition rate (number of frames)
0 to 999 • “Current” = current value
Direction ToOn, ToOff, Any Key on/off
• “ToOn” = on
• “ToOff” = off
• “Any” = on/off switching
KeyCut ME ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
ME1Main&Sub to ME5Main&Sub,
PPMain&Sub
Key Key1 to Key8 Key
Direction ToOn, ToOff, Any Key on/off
• “ToOn” = on
• “ToOff” = off
• “Any” = on/off switching
Play Device 1 to 12 Device
FrameMemory1Clip to • “1 to 12” = device 1 to 12
FrameMemory16Clip
ClipPlayer1 to ClipPlayer4
Mode Normal, Recue, Loop Playback mode
• Set to “Normal” (fixed) for
FrameMemory1Clip to FrameMemory16Clip
and ClipPlayer1 to ClipPlayer4
Cue Device 1 to 12 Device
FrameMemory1Clip to • “1 to 12” = device 1 to 12
FrameMemory16Clip
ClipPlayer1 to ClipPlayer4
Timecode Current Start point timecode
hh:mm:ss:ff • “Current” = current value
• “hh:mm:ss:ff” = hour:minute:second:frame
format
• “hh” set to “01” (fixed) for
FrameMemory1Clip to FrameMemory16Clip
and ClipPlayer1 to ClipPlayer4
Stop Device 1 to 12 Device
FrameMemory1Clip to • “1 to 12” = device 1 to 12
FrameMemory16Clip
ClipPlayer1 to ClipPlayer4
379
Symbol Parameter Parameter setting values Description
DiskFileLoad Device 1 to 12 Device
• “1 to 12” = device 1 to 12
FileName Filename File name (up to 23 characters)
DiskFolderSet Device 1 to 12 Device
• “1 to 12” = device 1 to 12
FolderName Folder Name Folder name (up to 23 characters)
Snapshot Region ME1 to ME5, PP Region
ME1Sub to ME5Sub, PPSub
User1 to User8
DME1 to DME4
Router
Register 1 to 99 Register number
Attribute Off Temporary attribute
Dissolve
Auto Transition
Dissolve&AutoTransition
Time Current Duration of effect dissolve
• “Current” = current value
KeySnapshot ME ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
ME1Main&Sub to ME5Main&Sub,
PPMain&Sub
Key Key1 to Key8 Key
Register 1 to 4 Register number
WipeSnapshot ME ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
Register 1 to 10 Register number
DMEWipeSnapshot ME ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
Register 1 to 10 Register number
TimelineRecall Region ME1 to ME5, PP Region
ME1Sub to ME5Sub, PPSub
User1 to User8
DME1 to DME4
Device1 to Device12
PBus
GPI
Register 1 to 399 Register number
TimelineRun Region ME1 to ME5, PP Region
ME1Sub to ME5Sub, PPSub • “Current” = currently selected region
User1 to User8
DME1 to DME4
Device1 to Device12
PBus
GPI
Current
TimelineRewind Region ME1 to ME5, PP Region
ME1Sub to ME5Sub, PPSub • “Current” = currently selected region
User1 to User8
DME1 to DME4
Device1 to Device12
PBus
GPI
Current
380
Symbol Parameter Parameter setting values Description
TimelineFF Region ME1 to ME5, PP Region
ME1Sub to ME5Sub, PPSub • “Current” = currently selected region
User1 to User8
DME1 to DME4
Device1 to Device12
PBus
GPI
Current
Shotbox Register 1 to 99 Register number
Pause Time 0 to 999 Pause time (number of frames)
StartTC Device 1 to 12 Device
FrameMemory1Clip to • “1 to 12” = device 1 to 12
FrameMemory16Clip
ClipPlayer1 to ClipPlayer4
RouterXpt DestinationButton 1 to 128 Destination selection delegation button number
Source 1 to 9999 Source number
Level 1 to 8 Level number
PatternLimit ME ME1 to ME5, PP Switcher bank
Status ToOn, ToOff, Any Enable/disable pattern limit
• “ToOn” = enable
• “ToOff” = disable
• “Any” = enabled/disable switching
TransitionType ME ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
ME1Main&Sub to ME5Main&Sub,
PPMain&Sub
TransitionType Mix Transition type
NAM
SuperMix
PresetColorMix
Wipe
DMEWipe
FM1&2Clip to FM15&16Clip
KeyTransitionType ME ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
ME1Main&Sub to ME5Main&Sub,
PPMain&Sub
Key Key1 to Key8 Key
Direction On, Off, Any Key on/off
• “On” = on
• “Off” = off
• “Any” = on/off switching
KeyTransitionType Mix Transition type
Wipe
DMEWipe
NextTransition ME ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
ME1Main&Sub to ME5Main&Sub,
PPMain&Sub
All On, Off Next transition
KeyPriority On, Off Next transition
BKGD On, Off Next transition
Key1 to Key8 On, Off Next transition
FadeToBlack Time Current Transition rate (number of frames)
0 to 999 • “Current” = current value
381
Symbol Parameter Parameter setting values Description
TLDirectionNormal Region ME1 to ME5, PP Region
ME1Sub to ME5Sub, PPSub • “Current” = currently selected region
User1 to User8
DME1 to DME4
Device1 to Device12
PBus
GPI
Current
TLDirectionReverse Region ME1 to ME5, PP Region
ME1Sub to ME5Sub, PPSub • “Current” = currently selected region
User1 to User8
DME1 to DME4
Device1 to Device12
PBus
GPI
Current
TLNormalReverseOn Region ME1 to ME5, PP Region
ME1Sub to ME5Sub, PPSub • “Current” = currently selected region
User1 to User8
DME1 to DME4
Device1 to Device12
PBus
GPI
Current
TLNormalReverseOff Region ME1 to ME5, PP Region
ME1Sub to ME5Sub, PPSub • “Current” = currently selected region
User1 to User8
DME1 to DME4
Device1 to Device12
PBus
GPI
Current
UtilityButton UtilityModule UtilityBox Utility control block
Button 1 to 300 Button
UtilityStatus On, Off Utility function on/off
Current • “On” = on
• “Off” = off
• “Current” = current status
Rewind Device 1 to 12 Device
FrameMemory1Clip to • “1 to 12” = device 1 to 12
FrameMemory16Clip
ClipPlayer1 to ClipPlayer4
FF Device 1 to 12 Device
FrameMemory1Clip to • “1 to 12” = device 1 to 12
FrameMemory16Clip
ClipPlayer1 to ClipPlayer4
ClipRecall Device FM1 to FM16 Device
ClipPlayer1 to ClipPlayer4
ClipType Pair, Single Image content type
ClipFilePath Clip File Path Folder path and content name of image
content
(folder name and content name delimited by
slash (/) characters)
Audio Device FM1 to FM16 Device
ClipPlayer1 to ClipPlayer4
AudioMode On, Off Enable/disable audio
FMLoop Device FM1 to FM16 Device
ClipPlayer1 to ClipPlayer4
FMLoopMode On, Off Enable/disable loop
382
Symbol Parameter Parameter setting values Description
KeyBusUtilButton ME ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
ME1Main&Sub to ME5Main&Sub,
PPMain&Sub
Bank 1 to 10 Bank number
KeyBusButton 1 to 24 Button number
UtilityStatus On, Off Utility function on/off
Current • “On” = on
• “Off” = off
• “Current” = current status
DeviceRecord Device 1 to 12 Device
AuxMix AuxMixBus Aux1, Aux3, … Aux47 Odd-numbered AUX bus
AuxMixStatus On, Off Enable/disable AUX mix
XptRowAssign MEBank ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
Row 1st, 2nd, 3rd, 4th Button row
BusFunction A, B Bus or bank
Key1 to Key8
Key1Source to Key8Source
Utility1, Utility2
DMEExternalVideo
DMEUtility1, DMEUtility2
EditPreview
Aux1 to Aux48
FrameMemory1, FrameMemory2
DME1Video to DME4Video
DME1Key to DME4Key
UtilShotbox1 to UtilShotbox10
GPITestFire Box DCU Fixed setting for GPI operation
Port 1 to 50 GPI output port number
NetworkMessaging Device 1 to 12 Device
Command Command Command (up to 23 characters)
XptTableForRow MEBank ME1 to ME5, PP Switcher bank
ME1Sub to ME5Sub, PPSub
Row 1st, 2nd, 3rd, 4th, 3rd&4th, All Button row
Table Main Cross-point assign table
Table1 to Table14 • “BankTable” = Table being set in switcher
BankTable bank
MacroTake Register All Register
• “All” = all paused macros
MacroCancel Register All Register
• “All” = all simultaneously executing macros
PrevKF Region Current Region
• “Current” = currently selected region
NextKF Region Current Region
• “Current” = currently selected region
TransitionRate ME ME1 to ME5, PP Switcher bank
Transition Background, BackgroundSub Transition
Key1 to Key8
Time 0 to 999 Transition rate (number of frames)
383
Button1 Button2 Button3 a)
Macro Attachment Lists UTIL1 Bus V 1st Row XPT 1 to
UTIL2 Bus K 1st Row XPT 128
DME EXT Bus V 1st Row Shift
DME Utility1 K 1st Row Shift
You can check macro attachment settings information in a DME Utility2 V 2nd Row
macro attachment list using the Home > Register > Macro Sub UTIL1 Bus K 2nd Row
> Attachment menu (18307.31). Sub UTIL2 Bus V 2nd Row Shift
The name of the control block on which a macro Sub DME EXT Bus K 2nd Row Shift
attachment is set is displayed in [Block]. Main&Sub UTIL1 Bus V 3rd Row
Main&Sub UTIL2 Bus K 3rd Row
The buttons on which a macro attachment is set are Main&Sub DME EXT Bus V 3rd Row Shift
displayed in [Button] in “Button1 Button2 Button3” EDIT PVW K 3rd Row Shift
format. AUX 1 to AUX 48 V 4th Row
Buttons are identified by the combination of “Button1”, FM1 K 4th Row
“Button2”, and “Button3”. FM2 V 4th Row Shift
K 4th Row Shift
Example:
Block: P/P XPT DME1V V 1st Row
Button1: UTIL1 Bus DME2V V 1st Row Shift
DME3V V 2nd Row
Button2: V 1st Row DME4V V 2nd Row Shift
Button3: XPT 2 V 3rd Row
“UTIL1 Bus V 1st Row XPT 2” is displayed in [Button]. V 3rd Row Shift
This indicates “P/P cross-point control block utility 1 bus, V 4th Row
1st row video signal, cross-point button number 2.” V 4th Row Shift
DME1K K 1st Row
DME2K K 1st Row Shift
DME3K K 2nd Row
M/E and P/P Blocks DME4K K 2nd Row Shift
K 3rd Row
Block: M/E-1 to M/E-5 XPT, P/P XPT K 3rd Row Shift
K 4th Row
Button1 Button2 Button3 a) K 4th Row Shift
A Bus 1st Row XPT 1 to a) When a cross-point button macro attachment is set to pair number mode, “Pair
B Bus 1st Row Shift XPT 128 XXX” (“XXX” is the pair number) is displayed after the button number.
KEY1 Bus to KEY8 Bus 2nd Row
Sub A Bus 2nd Row Shift Block: M/E-1 to M/E-5 Trans, P/P Trans
Sub B Bus 3rd Row
Sub KEY1 Bus to Sub KEY8 3rd Row Shift Button1 Button2 Button3
Bus 4th Row (blank) MIX –
Main&Sub A Bus 4th Row Shift Sub NAM a)
Main&Sub B Bus Main&Sub SUPER MIX a)
Main&Sub KEY1 Bus to PST COLOR MIX
Main&Sub KEY8 Bus WIPE
KEY1 Src Bus to KEY8 Src V 2nd Row DME WIPE
Bus K 2nd Row FM1&2 CLIP
Sub KEY1 Src Bus to Sub V 2nd Row Shift AUTO TRANS
KEY8 Src Bus K 2nd Row Shift CUT
Main&Sub KEY1 Src Bus to ALL a)
Main&Sub KEY8 Src Bus KEY PRIOR a)
BKGD
KEY1 to KEY8
NORM a)
NORM/REV a)
REV a)
Fader
PRIOR SET
None b)
KEY1 to KEY8 AUTO TRANS
Sub KEY1 to Sub KEY8 KEY ON
Main&Sub KEY1 to
Main&Sub KEY8
384
Other Blocks
Block: Trackball
385
Data Saved by [Setup Define] and [Initial Status
Define]
Switcher
Control panel
386
• Settings of mode selection buttons in the device control
Data Saved by [Initial Status Define] block
The following initial status data is saved when the
[Switcher/Content] button or [Panel] button in the [Initial
Status Define] group is pressed in the Home > Setup >
System > Start Up menu (19101.11).
Note
In multi program 2 mode, the operation mode setting is
saved in a snapshot when [Recall M/E Config] is enabled
in the Home > Setup > Switcher > Config > M/E Config
menu (19103.12), but it is not saved by [Initial Status
Define].
Saved data
• The following settings data for each switcher bank
Cross-points, transitions, independent key transitions,
key 1 to key 8, wipes, DME wipes, video process
• Color background 1 and 2
• AUX bus (including AUX mix)
• The following data for frame memory/clip player/SL
keys
Content load status
Frame memory output channel/clip player output
channel status (recalled content, channel combine, audio
enable/disable)
Key fill/key source status for SL keys (recalled content)
Loop, playback start point, and playback stop point
settings
[Variable Speed] button and playback speed settings
• Safe title
• DME override
• Home > DME menu data
Menu numbers: 1510n.01 to 1510n.53 (n = 1 to 4) and
15109.11 to 15109.31.
Control panel
Saved data
• Settings of buttons assigned to the function button
section of the cross-point control block
• Settings of delegation buttons assigned to the 1st row of
the cross-point control block
• Settings of mode selection buttons in the utility control
block
• Settings of banks in the utility control block
• Settings of mode selection buttons in the Flexi Pad
control block
• Settings of key delegation buttons in key operation mode
in the Flexi Pad control block
387
Control Panel
Maintenance
Notes
• Squeeze the cloth thoroughly before use to ensure that no
water droplets can enter the panel. The unit may become
damaged if water droplets enter the unit.
• Do not use cleaning agents, solvents, or detergents.
• Vigorous rubbing may scratch the unit.
Flexi Pad control block and utility control block
LCD buttons
If you have any concerns about dust or other matter on the
LCD buttons, contact your Sony service representative.
388
The material contained in this manual consists of Trademarks
information that is the property of Sony Corporation and is • Windows and Surface are trademarks or registered
intended solely for use by the purchasers of the equipment trademarks of Microsoft Corporation in the United
described in this manual. States and/or other countries.
Sony Corporation expressly prohibits the duplication of • Google Chrome is a trademark or registered trademark
any portion of this manual or the use thereof for any of Google LLC.
purpose other than the operation or maintenance of the • iPad Pro and Safari are trademarks of Apple Inc.,
equipment described in this manual without the express registered in the U.S. and other countries and regions.
written permission of Sony Corporation. • The SuperSpeed USB 5Gbps Trident logo is a registered
trademark of USB Implementers Forum, Inc.
389
XVS-G1
(SY)
5-031-086-11 (1) Sony Corporation © 2021