Professional Documents
Culture Documents
Mechanical float switch for dry run protection of LORENTZ solar pumps
The well probe provides a reliable method of run dry protection for LORENTZ pumps. The well probe
detects that water is present within a well, tank or other water source. The well probe is typically
attached to the riser pipe above the pump and connected to the controller. When the well probe
becomes dry (water level is below the probe) the pump switches off to avoid dry running.
Order Information
Item no.: 19-000005 Product name: Well probe sensor V2
Features
Reliable dry run protection
Simple to install using 3 cable ties
Improved tolerance to dirt
Splicing kit and cable ties for fixing are included
Technical Data
Max. operating temperature 55°C
Enclosure class: IP68
Submersion depth: max 50 m (164 ft)
Cable length: 1.5 m
Wire size: 2 x 0.50 mm² or AWG 20, waterproofed
Must be mounted in a vertical position
Meets the requirements for CE
Dimensions / Weight
Packaging dimensions: 255 x 170 x 40 mm
10.0 x 6.7 x 1.6 in
Total weight: 0.1 kg / 0.2 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Float Switch
Mechanically Activated Device for Water Level Detection in Applications
with LORENTZ Solar Pump Systems
The switch can be used to detect the water level within a tank. When the water level in the tank
reaches the maximum, the LORENTZ Controller will stop the pump and indicates Tank Full LED.
ORDER INFORMATION
• Item no.: 19-000030 product name: Float Switch
FEATURES
• N.O. (normally open) and N.C. (normally closed) function
• Reliable water level detection
• Simple to install
• Trouble free operation
• Not sensitive to rotation
• Corrosion-free
TECHNICAL DATA
• Operating temperature: -10°C to 55°C
• Storage temperature: : -10°C to 55°C
• Enclosure class: IP68
• Cable length: 3m, waterproof
• Wire size: 3x 1.0mm² or AWG 18
• Meets the requirements for CE
DIMENSION/WEIGHT
• Packaging dimensions: 230 x 160 x 55 mm
9.1 x 6.3 x 2.2 in
• Total weight: 0.8 kg / 1.8 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Pressure Switch
Device for Water Pressure Detection in Applications with LORENTZ Solar
Pump Systems
The switch can be used to detect the water level within a tank. When the water level in the tank
reaches the maximum, the pressure will increase and the LORENTZ Controller will stop the pump and
indicates Tank Full LED.
ORDER INFORMATION
• Item no.: 19-000310 product name: Pressure Switch 1-5bar
FEATURES
• Reliable water pressure detection
• Simple to install
• Trouble free operation
• Corrosion-free
TECHNICAL DATA
• Pressure range between 1 and 5 bar
• 2x cable gland Ø 5-9mm
• G ¼’’ pipe thread
• Meets the requirements for CE
DIMENSION/WEIGHT
• Packaging dimensions: 130 x 105 x 65 mm
5.1 x 4.2 x 2.6 in
• Total weight: 0.5 kg / 1 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Liquid Level Sensor
Sensor for measuring the level of liquid in a well or tank
USE / PURPOSE
The range of liquid level sensors use pressure to measure the liquid level in a well or tank. The sensors can be used for
collection of long term liquid level monitoring and also for pump control in applications where a well probe cannot be
used. The liquid level sensor must be used with a compatible LORENTZ Controller (see requirements).
FEATURES
• Gauge pressure sensor, pressure measurement relative to atmosphere
• For measuring levels of liquid in a well or tank
• Accurate, robust sensor
• For use with LORENTZ PumpScanner and pumpMANAGER
REQUIREMENTS
• LORENTZ PS2 controller, LORENTZ PSk2 controller or PS Controller equipped
with a licensed PS DataModule
• The cable contains a capillary tube to balance the sensor against atmospheric
changes. The sensor must be ordered with the required cable length for the
application as it cannot be spliced. Further cable lengths are available on demand,
please contact LORENTZ.
ORDER INFORMATION
Item # Product Pressure range Cable length
0-100 kPa
Liquid Level Sensor,
19-005040 0 to 10 m / 0 to 33 ft 30 m / 100 ft *
0-10m/33ft, 30m/100ft Cable
0 to 1 bar / 0 to 14.5 psi
0-200 kPa
Liquid Level Sensor,
19-005050 0 to 20 m / 0 to 66 ft 40 m / 130 ft *
0-20m/66ft, 40m/130ft Cable
0 to 2 bar / 0 to 29 psi
0-500 kPa
Liquid Level Sensor,
19-005080 0 to 50 m / 0 to 164 ft 60 m / 200 ft *
0-50m/164ft, 60m/200ft Cable
0 to 5 bar / 0 to 72.5 psi
0-1000 kPa
Liquid Level Sensor,
19-004395 0 to 100 m / 0 to 328 ft 140 m / 460 ft *
0-100m/328ft, 140m/460ft Cable
0 to 10 bar / 0 to 145 psi
*Further cable length is available on demand. Please contact LORENTZ.
BERNT LORENTZ GmbH
Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany
V180822
USE / PURPOSE
The sensors are commonly used to measure the pressure in the delivery pipeline or in a vessel. The pressure
signal is used with a LORENTZ pump controller to measure pressure and for pressure switching or constant
presure applications. The liquid pressure sensor must be used with a compatible LORENTZ Controller.
FEATURES
• Gauge pressure sensor, pressure measurement relative to atmosphere
• For measuring pressure in a pipe or vessel
• Accurate, robust sensor
• For use with LORENTZ PumpScanner and LORENTZ Global
REQUIREMENTS
• LORENTZ PS2 controller, LORENTZ PSk2 controller or LORENTZ PSk3 Controller
• Care must be taken to position the sensor without turbulent water
to ensure accurate measurement
• G1/4” or G1/2” female threaded filling / air vent hole is required to mount the sensor
The NWM Water Meter is a device for Characteristics Dimensions and weights
measuring flow in water applications.
½ All materials in contact with water Description DN25 DN32
The NWM water meter has a pulse are corrosion resistant. L [mm] 260 260
output for connection to LORENTZ ½ Five (5) digit mechanical display L1 [mm] 380 384
pump controllers. showing total liquid in 1m3 D [mm] G1-1/4B G1-1/2B
increments.
d [mm] R1 R1-1/4
The water meter is used in applications ½ Reed switch output which can
where measured flow and water be connected to PS2 and PSk H [mm] 117,5 117,5
volume values are required. controllers. H1 [mm] 206,5 206,5
½ Easy to install. W [mm] 98 98
The NWM Water Meter is suitable for Net Weight [kg] 2,6 3,1
applications with a pipe size of DN25 Technical Data
and DN32.
½ Water temperature max. 50°C
The NWM Water Meter contains a ½ Water pressure: max. 16 bar
special sealed liquid which is separate ½ Reed switch positioned on the
from the flow water to maximize x0,001 dial pointer: 10 l/imp.
readability, avoid fogging and avoid ½ Reed Switch cable length: 1,45m
scaling. ½ IP64
½ CE Conformity Order information
Flow DN25 DN32 The Accuracy curve shows the deviation in percent error
Max. flow rate: Qmax [m³/h] 7,87 12,5 for different flow rates. In regular operation the deviation
Nominal flow rate: Qn [m³/h] 6,3 10 is between -2% and +2%.
Transition flow rate: Qt [m³/h] 0,063 0,1
Packaging information
Minimum flow rate: Qmin [m³/h] 0,036 0,062
Error [%]
6
Description 19-002220 19-002225
4 Dimension [LxWxH] [mm] 310x280x250 310x280x250
2 Gross Weight [Kg] 3,5 3,9
Reed switch impulse data output X Volume [m³] 0,022 0,022
0 X
X
Reed switch impulse -2 X
Water meter size Liters per impulse
-4
DN25 10
-6
DN32 10
Qmin Qt Qn Qmax
Flow [m³/h]
1 2
220601
Water Meters Water Meters
Flow measuring instrument for water use Flow measuring instrument for water use
Error [%]
The WP Water Meter is a turbine type Characteristics Accuracy Curve 6
intended to measure high flow rates in ½ Removable and interchangeable The Accuracy curve shows the deviation in percent error for different flow 2
water applications. measuring element. rates. In regular operation the deviation is between -2% and +2%. 0
DN65 100 19-002165 Water meter, WP-DN50, 0.1 cbm/p 15 280x230x320 0,021
DN80 100 19-002170 Water meter, WP-DN65, 0.1 cbm/p 16 290x230x330 0,022
19-002180 Water meter, WP-DN80, 0.1 cbm/p 17 280x240x350 0,023
DN100 100
19-002190 Water meter, WP-DN100, 0.1 cbm/p 20 320x260x350 0,029
DN125 100
19-002200 Water meter, WP-DN125, 0.1 cbm/p 25 340x310x390 0,041
DN150 1000
19-002210 Water meter, WP-DN150, 1 cbm/p 38 370x340x420 0,053
DN200 1000
19-002202 Water meter, WP-DN200, 1 cbm/p 49 415x390x435 0,070
3 4
220601
SunSwitch
Automatic Solar Level Switching Device
The SunSwitch can be used for any application where you need to switch depending on the solar
intensity. It is an autonomous working unit that supplies itself with power from the PV-module on its
rear side.
ORDER INFORMATION
• Item no.: 19-000050 product name: SUN SWITCH Light-Sensor
FEATURES
• Trouble free operation
• Pump will only run when minimum flow rates or
pressure levels can be achieved which are required
by certain applications
• Reduced wear on the pump and motor since the
pump only starts when it will continue to run
TECHNICAL DATA
• Contact rating:
▪ Max. voltage 250 VAC / 220 VDC
▪ Max. current 2A
▪ Max. power 60 W / 62.5 VA
• Enclosure class: IP54
• Cable length: 4 m
• Wire size: 3x 1.0mm² or AWG 18, waterproofed
• Mounted close to the solar array
• Manual with further information
is available in PartnerNet
• Meets the requirements for CE
DIMENSION/WEIGHT
• Packaging dimensions: 230 x 115 x 90 mm
9.1 x 4.5 x 3.5 in
• Total weight: 1.2 kg / 0.6 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Cable Splice Kit 2.5 to 6 mm²
Kit for Permanently Insulate and Seal Cable Splice
ORDER INFORMATION
• Item no.: 19-000010 product name: Cable splice kit 2.5-6sqmm
FEATURES
• Efficient watertight seal
• Simple to install
• High quality components
• Kit for wire sizes from 2.5 to 6 mm²
INCLUDED IN DELIVERY
Four splices per kit:
DIMENSION/WEIGHT
• Packaging dimensions: 400 x 120 x 30 mm
15.8 x 4.7 x 1.2 in
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Cable Splice Kit 6 to 10 mm²
Kit for Permanently Insulate and Seal Cable Splice
ORDER INFORMATION
• Item no.: 19-000020 product name: Cable splice kit 6-10sqmm
FEATURES
• Efficient watertight seal
• Simple to install
• High quality components
• Kit for wire sizes from 6 to 10 mm²
INCLUDED IN DELIVERY
Four splices per kit:
DIMENSION/WEIGHT
• Packaging dimensions: 400 x 120 x 30 mm
15.8 x 4.7 x 1.2 in
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PV Combiner 1000-125-4
Connection box or parallel PV wiring
Description
An outdoor rated, combining connection box that
allows up to 4 strings of PV modules to be con-
nected safely to a solar pump system.
This product is typically used to combine strings
from multiple LORENTZ 1000-40-5 PV Discon-
nects.
Features
Combining function, allows 4 strings to be con-
nected to the solar pump system
Robust weather proof housing designed to
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Mounting options
Wall mount using 4 holes with weather
protection
Designed for optional pole mounting. Mounting
points are pre-marked inside the housing.
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Sacrificial Anode for HR Pump
Zinc sacrificial anode for corrosion protection of HR pump ends
USE / PURPOSE
The LORENTZ Sacrificial Anode is designed for use with LORENTZ pump ends. Where solar pump ends operate in aggres-
sive water conditions acidic water can attacks the passive layer of the high quality-steel pump end. This corrosion re-
duces the life time of the product. The LORENTZ Sacrificial Anode protects the pump system from this type of corrosion
and extends the pump life
ORDER INFORMATION
• Item no.: 19-002621 Product name: Anode, Sacrificial Zink Anode, Di42mm
• Item no.: 19-002622 Product name: Anode, Sacrificial Zink Anode, Di48mm
FEATURES
• Simple and cost effective part to protect the pump end from corrosion
• Designed for HR pump ends
TECHNICAL DATA
Application
The LORENTZ Sacrificial Anode is designed for use with LORENTZ pump units. Where a pump unit operates in aggressive
water conditions acidic water can attack the surface of the high quality-stainless steel pump unit. This corrosion reduc-
es the life expectancy of the product. The LORENTZ Sacrificial Anode reduces corrosion at pump end and extends the
pump life time.
ORDER INFORMATION
Simple and cost effective part to reduce corrosion at pump end and motor
Designed for installation around the body of 4” and 6“ motors below the pump end.
4” version requires a minimum 6” well / 6” version requires a minimum 8” well
Zinc anodes
Stainless steel clamps and screws
Item No motor Qty. of anodes Outer diameter length Zinc Weight Zinc Surface
147 mm 1.64 kg 58300 mm²
19-002630 4” motors 4
5.78 in 160 mm 3.63 lbs. 90 inch²
185 mm 6.30 in 2.46 kg 87470 mm²
19-002632 6” motors 6
7.28 in 5.43 lbs 136 in²
DIMENSION/WEIGHT
Packing dimensions: 180 x 180 x 50 mm / 7.1 x 7.1 x 2.0 in
Total packing weight: 2.0 kg / 4.4 lbs or 2.8kg / 6.2lbs
Application
The LORENTZ Sacrificial Anode is designed for use with LORENTZ pump units. Where a pump unit operates in aggressive
water conditions acidic water can attack the surface of the high quality-stainless steel pump unit. This corrosion reduc-
es the life expectancy of the product. The LORENTZ Sacrificial Anode reduces corrosion at pump end and extends the
pump life time.
ORDER INFORMATION
Simple and cost effective part to reduce corrosion at pump end and motor
Designed for installation around the body of 4” and 6“ motors below the pump end.
4” version requires a minimum 6” well / 6” version requires a minimum 8” well
Zinc anodes
Stainless steel clamps and screws
Item No motor Qty. of anodes Outer diameter length Zinc Weight Zinc Surface
147 mm 1.64 kg 58300 mm²
19-002630 4” motors 4
5.78 in 160 mm 3.63 lbs. 90 inch²
185 mm 6.30 in 2.46 kg 87470 mm²
19-002632 6” motors 6
7.28 in 5.43 lbs 136 in²
DIMENSION/WEIGHT
Packing dimensions: 180 x 180 x 50 mm / 7.1 x 7.1 x 2.0 in
Total packing weight: 2.0 kg / 4.4 lbs or 2.8kg / 6.2lbs
ORDER INFORMATION
• Item no.: 19-000200 product name: Inline Filter 10” PS150 BOOST
• Item no.: 19-000210 product name: Filter cartridge 10” PS150 BOOST
FEATURES
• Simple to install with included wall holder kit
• Clear bowl for easy maintenance
• Additional spare filter cartridges can be ordered
TECHNICAL DATA
• Inlet: female NPT 1/2”
• Outlet: female NPT 1/2”
• Max. filter cartridge size: 9 7/8 in
• 20-micron spun polypropylene filter cartridges
• Max. water temperature: 50°C (120°F)
• Max. working pressure: 6 bar
• Meets the requirements for CE
DIMENSION/WEIGHT
• Packaging dimensions: 450 x 250 x 250 mm
17.7 x 9.8 x 9.8 in
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PS BOOST Installation Kit
Control unit for use in pressurizing applications
The PS BOOST Installation Kit can be used for any application where a pressure tank is required. If the
pressure increases to the maximum, the LORENTZ PS Controller will stop the pump and indicates
Tank Full LED.
ORDER INFORMATION
Item no.: 19-000190 product name: PS BOOST Inst. Kit
FEATURES
Unit consist of the LORENTZ Pressure Switch,
a check valve, a pressure gauge, a pressure relief
valve, two ball valves and two short pipes
Reliable water pressure detection
Trouble free operation
Corrosion-free
TECHNICAL DATA
Min. cut-in: 1bar
Max. cut-out: 5bar
Pressure relief valve: 5.3bar
Enclosure class: IP44
Inlet: female G1/2”
Outlet: male G1/2”
Meets the requirements for CE
DIMENSION/WEIGHT
Packing dimensions: 600 x 320 x 170 mm
23.6 x 12.6 x 6.7 in
installation sample
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PM Accessory bracket
Kit for mounting LORENTZ PS Controller / PV-
Disconnect to the Pole Mount PM-1-X
USE / PURPOSE
The PM Accessory bracket is designed for use with the LORENTZ
POLE MOUNT-1-X.
The Set allows an easy and flexible mounting of LORENTZ PS Con-
trollers and PV-Disconnect on the Pole of the LORENTZ PM-1-X.
ORDER INFORMATION
Part Item No. PM-1-1 PM-1-2 PM-1-3 PM-1-4 PM-1-5 PM-1-6
PM Accessory bracket 2.5-1 19-004220 x x
PM Accessory bracket 4-1 19-004210 x x x x
FEATURES
Simple and cost effective mounting possibility for LORENTZ Controller and PV-Disconnect
Designed for LORENTZ Pole Mount 1-X
TECHNICAL DATA
Packing dimensions
305x170x25 mm
12x7x1 inch
SmartSolution OVERVIEW
PSk2 controller SmartPSUk2 SmartStart generator
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Order information Mounting options
W1 D1 W2
d
H1
H2
H
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
SmartStart
Automatic Remote Diesel Generator Switching Device
Description
Max. switching capability: 250 V AC / The SmartStart comes with two cables, NP7-12 or a similar sealed 12 V lead-
30 V DC, 2 A one cable to be used with the PSk2 acid battery
Enclosure class: IP54 product line and one cable to be used Recommended minimum capacity: 7
Nominal cross section for remote start with the PSk3 product line. Each cable Ah
cable 1.5 mm² is ready to use and has a length of Max. dimensions without connector:
Further information is available in the 2 m. The required battery must be 151 x 70 x 95 mm (5.94 x 2.56 x 3.74
PSk2 and PSk3 manual on partnerNET ordered separately. The battery must in)
meet the requirements on the right. Max height with connector: 100 mm
(3.94 in)
Connector: 4.8 mm (0.189 in) faston
tabs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Mounting options Order information
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Sun Sensor
Irradiation measurement module and software
The LORENTZ Sun Sensor module and software allow the PS2 and PSk2 controller to accurately
estimate irradiation levels and control the pump based on this.
The Sun Sensor function can be configured to offer the pump mechanical protection from
repeated starts and stops due to low irradiation. The Sun Sensor function can also be configured to
switch external devices via the output terminal.
Each module is tested and specially calibrated for use with the PS2 and PSk2 system. The module
also includes a software license to use the features which is accessed via the item serial number.
This Sun Sensor module is included with any PS2-1800 or PS2-4000 controller and any PSk2
controller.
ORDER INFORMATION
• Item no.: 19-005030
• Product name: Sun Sensor module
TECHNICAL DATA
• Open circuit voltage Voc = 10.2 V
• Short circuit current Isc = 0.19 A
• Wire size: 2x 1.0mm² / AWG 18, waterproofed
• Mount in parallel to the solar array
• PS2/PSk2 manual with further information
is available in partnerNet
• Meets the requirements for CE
DIMENSION/WEIGHT
• Packaging dimensions: 180 x 205 x 60 mm
7.08 x 8.07 x 2.36 in
• Total weight: 0.6 kg / 1.33 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Flow Sleeve for HR(E) Pumps
Device to protect the pump from dirt and for motor cooling
A flow sleeve is a sleeve that goes around the pump body and motor. It has two functions:
1. A flow sleeve reduces the amount of dirt in the pump. Where water sources contain sand or
have the potential for dirt falling into them (uncapped wells) a flow sleeve is recommended to
protect the pump from dirt. Due to the large inner diameter of the flow sleeve the water rises
very slowly and dirt deposits at the bottom of the well. Subsequently, water with less
sediments enters the pump which increases its lifetime.
2. A flow sleeve cools the motor. In open water, tanks or pools there is no natural flow of water
across the motor which can lead to heat build-up. The tube enforces water flow across the
motor which has a cooling effect.
ORDER INFORMATION (please compare (1), (2) etc. with the sample flow sleeve)
Item no. Product name Scope of delivery Suitable for
19-000220 Flow Sleeve Kit for (1) 1 x flow sleeve adapter All HR pumps
4” HR Pumps (2) 2 x hose clamp with 4" motor
(3) 4 x countersunk bolt
M6x20
(4) 1 x PVC tube: ø125x5,
19-000225 Flow Sleeve Kit for 800 mm length All HRE pumps
4” HRE Pumps with 4" motor
19-000240 Flow Sleeve Adaptor (1) 1 x flow sleeve adaptor All HR pumps
for 4” HR Pumps (2) 2 x hose clamp with 4" motor
19-000245 Flow Sleeve Adaptor (3) 4 x countersunk bolt All HRE pumps
for 4” HRE Pumps M6x20 with 4" motor
FEATURES
• Due to the large inner diameter of the flow sleeve the water
rises very slowly allowing dirt to settle at the bottom of the well
• The life expectancy of the pump is increased due to less sand
entering the pump
• Simple installation
• Can be used with PS2-200 – PS2-4000 HR(E) Pumps
• Min. well diameter of 6” (150 mm) required sample flow sleeve
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
DIMENSIONS/WEIGHT
Flow Sleeve Kit for 4” HR(E) Pumps (19-000220 or 19-000225):
• Packaging dimensions: 850 x 150 x 130 mm
33.5 x 6.0 x 5.1 in
• Total weight: 3.7 kg / 8.2 lbs
Flow Sleeve Adaptor for 4” HR(E) Pumps (19-000240 or 19-000245, without PVC tube):
• Packaging dimensions: 135 x 135 x 135 mm
5.3 x 5.3 x 5.3 in
• Total weight: 1.2 kg / 2.6 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Flow Sleeve for C-SJ Pumps
Device to protect the pump from dirt and for motor cooling
A flow sleeve is a sleeve that goes around the pump body and motor. It has two functions:
1. A flow sleeve reduces the amount of dirt in the pump. Where water sources contain sand or
have the potential for dirt falling into them (uncapped wells) a flow sleeve is recommended to
protect the pump from dirt. Due to the large inner diameter of the flow sleeve the water rises
very slowly and dirt deposits at the bottom of the well. Subsequently, water with less
sediments enters the pump which increases its lifetime.
2. A flow sleeve cools the motor. In open water, tanks or pools there is no natural flow of water
across the motor which can lead to heat build-up. The tube enforces water flow across the
motor which has a cooling effect.
FEATURES
• Due to the large inner diameter of the flow sleeve the water
rises very slowly allowing dirt to settle at the bottom of the well
• The life expectancy of the pump is increased due to less sand
entering the pump
• Simple installation
• The flow sleeve must be selected according to the
pump system (see table)
• The required borehole diameter depends on the
diameter of the flow sleeve
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
ORDER INFORMATION (please compare (1), (2) etc. with the sample flow sleeve)
Item no. Product name Scope of delivery Suitable for
19-000230 Flow Sleeve Kit for (1) 1 x adaptor All 4" C-SJ pump ends
4" C-SJ Pumps with (2) 2 x hose clamp with 4" motor
4" Motor (3) 2 x cable strip
(4) 1 x PVC tube: D140x4, 0.5 m length
19-000250 Flow Sleeve Adaptor (1) 1 x adaptor All 4" C-SJ pump ends
for 4" C-SJ Pumps (2) 2 x hose clamp with 4" motor
with 4" Motor (3) 2 x cable strip
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
DIMENSIONS/WEIGHT
Flow Sleeve Kit for 4" C-SJ Pumps with 4" Motor (19-000230):
• Packaging dimensions: 590 x 150 x 130 mm
23.2 x 6.0 x 5.1 in sample flow sleeve
• Total weight: 3.3 kg / 7.3 lbs
Flow Sleeve Adaptor for 4" C-SJ Pumps with 4" Motor (19-000250, without tube):
• Packaging dimensions: 165 x 165 x 110 mm
6.5 x 6.5 x 4.3 in
• Total weight: 1.2 kg / 2.6 lbs
Flow Sleeve Adaptor for C-SJ17-X/30-X with 4" motor (19-000255, without tube):
• Packaging dimensions: 165 x 165 x 110 mm
6.5 x 6.5 x 4.3 in
• Total weight: 1.2 kg / 2.6 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PS2 Manual Speed Controller
Device to provide manual motor speed control of PS2 systems
The LORENTZ PS2 Manual Speed Controller allows adjustment of the maximum
motor speed without using the PumpScanner App. To use the Manual Speed
Controller, it is required to activate this function in the settings of PumpScanner
during or before installation.
Llk
ORDER INFORMATION
• Item no.: 19-000035 Product name: PS2 Manual Speed Controller
FEATURES
• Allows manual control of PS2 motor speed
• Outdoor rated, installed in the housing of the controller
TECHNICAL DATA
• Voltage: 15-24 V DC
• Enclosure class: IP65
• Ambient temperature: -38…50 °C (-36… 122 F)
• Wire size: 2 x 0,75 mm²/18 AWG
• Replaces Ø 20mm cable gland
• Meets the requirements for CE
• Please note that if “Manual Speed Controller” is configured then “Set speed limitation” function
is not available in PumpScanner.
DIMENSION/WEIGHT
• Packing dimension : 100 x 70 x 35 mm; 3.9 x 2.7 x 1.3 in
• Total weight: 0.2 kg / 0.4 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PV Disconnect 1000-300-30
30 string connection box with DC disconnect switch and surge
protection
ORDER INFORMATION
FEATURES
Simple and cost-effective unit to
connect up to 30 module strings
in parallel
Includes an appropriate DC rated
disconnect switch and string fuses
(15 A)
Includes surge protection
Designed for PSk2-100 pump
A
systems
DIMENSION/WEIGHT B[mm]
TECHNICAL DATA A
B
Wiring of up to 30 PV strings in
parallel
DC rated disconnect switch enc-
losed
Enclosure class IP 54
Meets the requirements for CE
1,000 V DC (Uoc)
Max. voltage
880 V DC (Ump)
Max. current per
15 A
string
Max. total current 300 A
Dimension in mm [in]
A B C D E Weight in kg [lbs]
1170 1100 600 650 230 68
[46.06] [43.31] [23.62] [25.60] [9.06] [149.91]
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PS 2 Controller Plug Kit
Kit for an easy and electrical safe installation of PS2 Controller
The LORENTZ PS2 Controller Plug Kit can be installed on any PS2 system. The kit extends the internal
wiring connections to plugs allowing systems to be pre-wired and delivered to site. Possible uses for the
plug kit are where time on site needs to me minimized, where systems are often moved or where the
skills available onsite do not allow for a standard installation.
The sensor extension kit allows the installation of two additional sensors, the standard set contains only
two plug sets for sensor connections.
Order Information
Features
Technical Data
Ambient
PLUG Wire size max. current max. voltage
temperature
max, 6mm²
Motor 32 A 600V DC -40°C … +90°C
(10 AWG)
40 A
max 8mm²
PV (27A at 2.5mm² 1500V DC -40°C …+90°C
(8 AWG)
/14AWG)
max. 1.5mm²
Sensor 3A 50V DC -40°C …+90°C
(16 AWG)
Packing Dimension/Weight
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PS2-100 Well Probe
Mechanical float switch for run-dry protection of PS2-100 solar pumps
The PS2-100 Well Probe provides a reliable method of run-dry protection. It detects that water is
present within a well, tank or other water source. The well probe is typically attached to the riser pipe
above the pump and connected to the controller. When the well probe becomes dry (water level is
below the probe) the pump switches off to avoid dry running.
ORDER INFORMATION
Item no.: 19-000007 Product name: Well Probe with 15 m / 49 ft cable and a XT-30F plug
FEATURES
Reliable run-dry protection
Simple to install using pre-fitted plug
TECHNICAL DATA
Max. operating temperature 55°C / 131°F
Enclosure class: IP68
Submersion depth: max 50 m / 164 ft
Wire size: 2 x 0.75 mm² or AWG 19, waterproofed
15 m / 49 ft cable with XT-30F plug
Must be mounted in a vertical position
Meets the requirements for CE
DIMENSION / WEIGHT
Packaging dimensions: 205 x 160 x 80 mm
8.1 x 6.3 x 3.1 in
Total weight: 0.85 kg / 1.9 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PS2-100 Motor Extension Cable
Cable with plugs to extend the motor cable on PS2-100 systems
This 15 m / 50 ft cable is used to extend the motor cable on PS2-100 pump systems. The cable has a 3
pin MT-60M connector on one end and a MT-60F connector on the other end. The extension cable
comes with a waterproof connector tube which seals the cable connection and provides strain relief.
ORDER INFORMATION
• Item no.: 19-001220
• Product name: PS2-100 15 m / 50 ft Motor Extension Cable
FEATURES
• Cable with plugs
• Simple to install
• Includes waterproof connector tube
TECHNICAL DATA
• Operating temperature: -10°C to 55°C / 14°F to 131°F
• Storage temperature: -10°C to 55 °C / 14°F to 13°F
• Cable length: 15 m / 50 ft, waterproof
• Wire size: 3 x 2.5 mm² or AWG 14
• Meets the requirements for CE
DIMENSION / WEIGHT
• Packaging dimensions: 385 x 385 x 130 mm
15.1 x 15.1 x 5.1 in
• Total weight: 3.6 kg / 7.9 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PS2-100 Float Switch
Mechanically activated device for water level detection
The PS2-100 Float Switch can be used to detect the water level in a tank. When the water level in the
tank reaches the maximum the LORENTZ PS2-100 Controller will stop the pump and indicates tank full
LED.
ORDER INFORMATION
• Item no.: 19-000032 product name: PS2-100 Float Switch with 10 m / 33 ft cable
FEATURES
• NC (normally closed) function
• Reliable water level detection
• Simple plug-in installation
• Trouble-free operation
• Not sensitive to rotation
• Corrosion-free
TECHNICAL DATA
• Operating temperature: -10°C to 55°C / 14°F to 131°F
• Storage temperature: -10°C to 55°C / 14°F to 131°F
• Enclosure class: IP68
• Cable length: 10 m / 33 ft, waterproof
• Meets the requirements for CE
DIMENSION / WEIGHT
• Packaging dimensions: 250 x 205 x 105 mm
9.8 x 8.1 x 4.1 in
• Total weight: 1.9 kg / 4.2 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Surge Protector2
Device to Protect LORENTZ Pump Accessories from Voltage Spikes
ORDER INFORMATION
• Item no.: 19-005210 product name: Surge Protector2
FEATURES/COMPATIBILITY
• Reliable surge protection device for any switched, pulse or
analogue (4-20 mA) inputs sensors including:
o Well Probe Sensor 19-000000
o Water Sensor 19-000001
o Float Switch 19-000030
o Pressure Switch 19-000310
o Liquid Level (all types, e.g. 19-005040)
o Liquid Pressure Sensor (all types, e.g. 19-004460)
o Water Meter (all types, e.g. 19-002160)
o Sun Switch (19-000050)
• The device must be installed inside the PS2 or PSk2 controller.
TECHNICAL DATA
• Max. voltage: 30 V DC
• Max current 8/20µs: 500 A
• Enclosure class: IP20
• Ambient temperature: max. 80°C (176°F)
• Wire size: 2 x 1.5mm² (AWG 16)
• Meets the requirements for CE
DIMENSION/WEIGHT
• Packing dimensions: 56 x 26 x 120 mm
2.2 x 1.02 x 0.47 in
• Total weight 0.1 kg / 0.2 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PS2-100 Extension Cable for
Well Probe / Float Switch
Cable with plugs to extend the well probe / float switch cable on PS2-100
systems
This 15 m / 50 ft cable is used to extend the well probe cable on the PS2-100 pump system. The cable
has a 2 pin XT-30M connector on one end and a XT-30F connector on the other end. The extension
cable comes with a waterproof connector tube which seals the cable connection and provides strain
relief.
ORDER INFORMATION
• Item no.: 19-001240
• Product name: PS2-100 15 m / 50 ft Well Probe / Float Switch Extension Cable
FEATURES
• Cable with plugs
• Simple to install
• Includes waterproof connector tube
TECHNICAL DATA
• Operating temperature: -10°C to 55°C / 14°F to 131°F
• Storage temperature: -10°C to 55°C / 14°F to 131°F
• Enclosure class: IP68
• Cable length: 15 m / 50 ft, waterproof
• Wire size: 2 x 1 mm² or AWG 17
• Meets the requirements for CE
DIMENSION / WEIGHT
• Packaging dimensions: 250 x 205 x 105 mm
8.1 x 8.1 x 4.1 in
• Total weight: 0.7 kg / 1.5 lbs
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Retrofit Adaptors for HR/HRE Pump
Adaptor set to combine HR and HRE pump design
PURPOSE
LORENTZ introduced the next evolution of the helical rotor pump, called HRE. This HRE design has different connection
dimension than the previous HR design. In case an ECDRIVE or a Pump End of the HRE generation shall be combined
with a component of the previous HR generation a retrofit adaptor set must be used.
ORDER INFORMATION
Item no. Product name Content of delivery Purpose
Packing Dimensions/Weight
SmartSolution OVERVIEW
PSk2 controller SmartPSUk2 SmartStart generator
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Order information Mounting options
W2 W2 W1 W1 D1 D1
d d
H2
H2
H1
H1
H
H
H2
H2
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PowerPack 150S
DC power supply for PS2 pump systems
Description
An outdoor rated power supply unit
to allow LORENTZ PS2-100 to PS2-
150 systems to be powered from an
AC (mains voltage) power source.
The PowerPack can be used as a
continuous supply, in conjunction
with PV modules or as a temporary
or seasonal supply.
Features
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Order information
Mounting options
Wall or panel mount using 4 holes with
weather protection
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PowerPack 600S
DC power supply for PS2 pump systems
Description
An outdoor rated power supply unit
to allow LORENTZ PS2-200 to PS2-
600 sytems to be powered from an
AC (mains voltage) power source.
The PowerPack can be used as a
continuous supply, in conjunction
with PV modules or as a temporary
or seasonal supply.
PowerPack 600S
For use with these PS2-200
Approvals and standards
Pump systems PS2-600
The switch mode power supply has the
AC input 100-260 V AC / 50 - 60 Hz
following approvals
EN62368-1 DC output 56 V - 10.5 A
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Order information
Mounting options
Wall or panel mount using 4 holes with
weather protection
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
PowerPack 4000S
DC power supply for PS2-4000 pump systems
Description
The PowerPack 4000S is an outdoor
rated power supply unit which allows
LORENTZ PS2-4000 systems to be po-
wered from an AC (mains voltage) power
source. The PowerPack 4000S can be PP4000S
AC PowerPack
OFF www.lorentz.de
v210521
*
SN
IEC/EN 62368-1*
IP33 ! EN 61000-6-2
EN61204-3
UL62368-1
Features
DC power supply to power LORENTZ
solar pump systems from the grid or a
generator
Single phase powered device
Robust weatherproof housing
Wall or panel mount possible
Efficiency up to 93%
External on / off switch plus LED
indicator
Forced air cooling by built-in fans
Protections against short circuit, over-
load, over voltage, over temperature,
fan failure
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Order information
A 280 mm / 11 in
B 350 mm / 13.8 in F D
C 140 mm / 5.5 in
D 334 mm / 13.1 in C A
E 384 mm / 15.1 in
F 180 mm / 7.1 in A= 28
B= 35
C= 14
B
E
D= 33
E= 38
Product Dimensions for Ins
F= 18
Mounting
Fixing pattern for holes: 310 x 292 mm /
12.2 x 11.5 in
F
C
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Water Level Measurement Solution
The LORENTZ Water Level This solution allows control of the Features
Measurement Solution (WLMS) pump based on the water level in the
accurately measures water levels source or tank. It delivers not only ½ Measures water levels in tank, well
in boreholes and tanks. WLMS is a information about the current water or other water source
combination of pressure sensor and level but also about trends related to ½ Provides pump run dry run
plug in barometer to provide water water usage. Predicting and planning protection
level measurement for PS2 and PSk3 for low water levels is possible with ½ Absolute pressure sensor -
systems. Used in conjunction with this solution. complete with plug in barometer
inbuilt software WLMS allows you to ½ Control of pump based on sensor
record and monitor water levels in The WLMS can also provide dry data
your tank and control your system run protection for the pump and ½ Very simple configuration and high
based on these levels. is a very good alternative to a well customer value
probe in any water source that is ½ Real time and historic level data
The sealed sensor comes with a plug- prone to calcium scaling, snails, is viewed locally via LORENTZ
in barometer placed in the controller algae or other contaminants that can CONNECTED apps (PumpScanner
and measures the pressure based on effect operation of mechanical float or Assistant or remotely via
the difference between the submersed switches. LORENTZ Global
sensor and the barometer.
Sensor type absolute pressure sensor ½ for use with LORENTZ PS2
Enclosure class IP68 controllers and LORENTZ PSk3
controllers
Sensor housing high tech polymer
Measuring range 25 m / 82 ft water level
Accuracy +/- 0.35 m / 1.15 ft
Diaphragm material stainless steel AISI316L
O-ring material FKM
Overpressure max 75m / 246 ft water column
Min shut off level 0.5 m / 1.6 ft
Output signal 4-20mA
Power supply 12-28V DC
Cable jacket PVC
Cable length 35 m / 114.8 ft
Application temperature -10 to 80° C / 14 to 176° F
Meets the requirements for CE
8
WLMS Ordering Information
Order information
Dimensions
Packing Dimensions Weight
225 x 205 x 70 mm / 8.9 x 8 x 2.8 in 1.5 kg / 3.3 lbs
Shipping Items
Splice kit
9
PowerPack 2000S
DC power supply for PS2-1800 and PS2-600 pump systems
Description
The PowerPack 2000S is an outdoor
rated power supply unit which allows
LORENTZ PS2-1800 and PS2-600 sys-
tems to be powered from an AC (mains
voltage) power source. The PowerPack
2000S can be used as a continuous
l
power supply, in conjunction with PV
a
INPUT AC WARNING!
Electric shock hazard, dangerous
O
Max. current 16 A
Frequency 47-63 Hz No user-serviceable parts inside.
INPUT DC
Before opening the cover, read
Max. PV voltage for PS2-1800 200 V
power supply.
instruction manual for proper
Max. PV voltage for PS2-600 150 V installation and operation.
OUTPUT DC
Features
DC power supply to power LORENTZ
solar pump systems from the grid or a
generator
Single phase powered device
Robust weatherproof housing
Wall or panel mount possible
Efficiency up to 93%
External on / off switch plus LED
indicator
Forced air cooling by built-in fans
Protections against short circuit, over-
load, over voltage, over temperature,
fan failure
PowerPack 2000S
Pump systems PS2-1800 / PS2-600
AC input voltage Single phase 200-240 V AC ± (10%)
AC current 20 A / 180 V AC 16 A / 230 V AC Additional certifications concerning the inbuilt
power supply:
Frequency 47-63 Hz
PV input PS2-1800 Max. 200 V DC (solar)
PV input PS2-600 Max. 150 V DC (solar)
DC output PS2-1800 up to 200 V DC (solar) 160 V DC
(PowerPack) 12-14 A
DC output PS2-600 up to 150 V DC (solar) 135 V DC
(PowerPack) 12-14 A
Working ambient temp. -20~ + 45°C (-4°F to 113°F)
IP class IP33
Remote control On-Off control function
Housing material Steel box
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
Order information
A 280 mm / 11 in
B 350 mm / 13.8 in F D
C 140 mm / 5.5 in
D 334 mm / 13.1 in C A
E 384 mm / 15.1 in
F 180 mm / 7.1 in A= 28
B= 35
C= 14
B
E
D= 33
E= 38
Product Dimensions for Inst
F= 18
Mounting
Fixing pattern for holes: 310 x 292 mm /
12.2 x 11.5 in
F D
C A
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
CLS Water Sensor CLS Water Sensor
Sensor for water presence detection Sensor for water presence detection
The CLS Water Sensor is a capacitive Characteristics CLS Water Sensor Drawing and Dimensions
limit switch sensor. It is used for
efficient and reliable detection of the ½ Water detection based on the
presence of liquid in pipes or open capacitive change principle.
tanks. The sensor operates on the ½ Quick reaction time.
principle of capacitance variation ½ Reliable fluid detection.
which is more reliable than resistive or ½ Robust and corrosion resistant:
inductive measurement between open Sensor made of AISI316,
probes. measuring tip made of PEEK
(polyetheretherketone).
The CLS Water Sensor is suitable as ½ Over current and reverse polarity
dry run protection for surface pump protection.
applications and can be also used to ½ LED indicator on the sensor.
detect the presence of water in tanks. ½ NPN output for use with water
sensor input on PS2 and PSk family Order information
controllers.
1 2
220928
PV Combiner 1000-15-3-F PV Combiner 1000-15-3-F
Connection Box for parallel wiring with integrated string fuses Connection Box for parallel wiring with integrated string fuses
Description Compatibility
The LORENTZ PV Combiner 1000-15- ½ For use with LORENTZ PS2 and
3-F is a PV connection box with fuses PSk controllers.
to be used with our PS2 and PSk pump
systems.
138
isolation for the control unit in the
187
219
138
187
219
event of an overcurrent situation from Net Weight 1.7 kg [3.7 lbs]
the PV array.
8
PV Fuse, 15A
½
specially designed for solar power Input cable size 2.5 - 10 mm² / AWG 14 - 8 [WxH, Hole diameter] [6.3 x 5.9, Ø0.236 in]
applications Output cable size 2.5 - 16 mm² / AWG 14 - 6
½ Robust, weatherproof housing,
Quantity of fuses 6
designed to make installation Order and Packaging information
Fuse current rating 15 A
simple
½ Lockable for additional protection. Fuse voltage rating 1000 V DC
Item number 19-001940
½ Internal touch protection with Fuse Size 10 x 38 mm
screws Product name PV Combiner 1000-15-3-F
PG glands (input) 6 x M16
½ Required for a professional PG glands (output) 2 x PG-11 Packed gross weight 2.4 kg [5.2 lbs]
installation of solar pumping
Enclosure class IP 68 Packed volume 0.0125 m3 [0.44 ft3]
systems
Housing material Polycarbonate Packaging dimensions
V220803
250 x 250 x 200 mm [9.8 x 9.8 x 7.8 in]
Approvals and standards EN 60204 / EN 6094-3 [LxWxH]
1 2
PV Combiner 1000-15-6-F PV Combiner 1000-15-6-F
Connection Box for parallel wiring with integrated string fuses Connection Box for parallel wiring with integrated string fuses
Description Compatibility
The LORENTZ PV Combiner 1000-15- ½ For use with LORENTZ PS2 and
6-F is a PV connection box with fuses PSk controllers.
to be used with our PS2 and PSk pump
systems.
219187
138
219
187
138
event of an overcurrent situation from Net Weight 2.8 kg [6.1 lbs]
the PV array. 8
8
PV Fuse, 15A
specially designed for solar power Input cable size 2.5 - 10 mm² / AWG 14 - 8 [WxH, Hole diameter] [10.6 x 5.9, Ø0.236 in]
applications Output cable size 2.5 - 16 mm² / AWG 14 - 6
½ Robust, weatherproof housing,
Quantity of fuses 12
designed to make installation Order and Packaging information
Fuse current rating 15 A
simple
½ Lockable for additional protection Fuse voltage rating 1000 V DC
Item number 19-001945
½ Internal touch protection with Fuse Size 10 x 38 mm
screws Product name PV Combiner 1000-15-6-F
PG glands (input) 12 x M16
½ Required for a professional PG glands (output) 2 x PG-11 Packed gross weight 3.4 kg [7.5 lbs]
installation of solar pumping
Enclosure class IP 68 Packed volume 0.018 m3 [0.63 ft3]
systems
Housing material Polycarbonate Packaging dimensions
V220801
360 x 250 x 200 mm [14.1 x 9.8 x 7.8 in]
Approvals and standards EN 60204 / EN 6094-3 [LxWxH]
1 2
PV Disconnect 400-50-3-P PV Disconnect 400-50-3-P
Connection Box with DC Disconnect Switch, String Fuses and Surge Connection Box with DC Disconnect Switch, String Fuses and Surge
Protection Device Protection Device
Description Compatibility
PV Fuse, 15A
parallel to the solar pump system. [WxH, Hole diameter] [10.6 x 5.9, Ø0.236 in]
Ground cable size ≥ 6 mm² / AWG 10
½ Built-in protection with Fuses and
Quantity of fuses 6
SPD.
½ Robust weatherproof housing Fuse current rating 15 A Order and Packaging information
designed to make installation Fuse voltage rating 1000 V DC
simple. Fuse Size 10 x 38 mm Item number 19-001975
½ Lockable to secure the system PG glands (input) 6 x M16
during maintenance (power locked Product name PV Disconnect 400-50-3-P
PG glands (output) 2 x PG-11
off). Packed gross weight 3.4 kg [7.5 lbs]
PG gland GND 1 x M16
½ Internal touch protection with
Packed volume 0.018 m3 [0.63 ft3]
screws. Enclosure class IP 68
Packaging dimensions
V220803
½ Required for a professional Housing material Polycarbonate 360 x 250 x 200 mm [14.1 x 9.8 x 7.8 in]
installation of solar pumping [LxWxH]
Approvals and standards EN 60947-3 / 6094-3
systems
1 2
PV Disconnect 400-50-1-S PV Disconnect 400-50-1-S
Connection Box with DC Disconnect Switch and Surge Protection Device Connection Box with DC Disconnect Switch and Surge Protection Device
Description Compatibility
187
requires a reliable ground connection.
218
[LxWxH] [8.6 x 5.4 x 7.8 in]
187
218
139
The product can connect one (1) string
139
Net Weight 1.7 kg [3.7 lbs]
of PV Modules through the enclosed
DC disconnect switch safely to a solar
pump system.
V220802
Packaging dimensions
Housing material Polycarbonate 250 x 250 x 200 mm [9.8 x 9.8 x 7.8 in]
[LxWxH]
Approvals and standards EN 60204-1 / EN 60947-3
1 2
PV Disconnect 400-50-3-S PV Disconnect 400-50-3-S
Connection Box with DC Disconnect Switch and Surge Protection Device Connection Box with DC Disconnect Switch and Surge Protection Device
Description
Compatibility
The LORENTZ PV Disconnect 400-
50-3-S is a PV connection box with an ½ For use with LORENTZ PS2
integrated DC disconnect switch, a controllers [PS2-150 to PS2-4000].
combining function and additionally
is equipped with a Surge Protection
Device (SPD), for use with LORENTZ
PS2 pump systems.
V220803
½ Required for a professional Housing material Polycarbonate 360 x 250 x 200 mm [14.1 x 9.8 x 7.8 in]
installation of solar pumping [LxWxH]
Approvals and standards EN 60204-1 / EN 60947-3
systems
1 2
PV Disconnect 400-50-6-S PV Disconnect 400-50-6-S
Connection Box with DC Disconnect Switch and Surge Protection Device Connection Box with DC Disconnect Switch and Surge Protection Device
Description
Compatibility
The LORENTZ PV Disconnect 400-
50-6-S is a PV connection box with an ½ For use with LORENTZ PS2
integrated DC disconnect switch, a controllers [PS2-150 to PS2-4000].
combining function and additionally
is equipped with a Surge Protection
Device (SPD), for use with LORENTZ
PS2 pump systems.
V220803
½ Required for a professional Housing material Polycarbonate 360 x 250 x 200 mm [14.1 x 9.8 x 7.8 in]
installation of solar pumping [LxWxH]
Approvals and standards EN 60204-1 / EN 60947-3
systems
1 2
PV Disconnect 1000-50-5 PV Disconnect 1000-50-5
Connection Box with DC Disconnect Switch Connection Box with DC Disconnect Switch
Description Compatibility
187
187
217
139
217
139
Designed to be installed between Net Weight 2.1 kg [4.7 lbs]
the solar generator and the pump 8
8
Mounting options
V220803
Approvals and standards Switch IEC 60947-3 360 x 250 x 200 mm [14.1 x 9.8 x 7.8 in]
[LxWxH]
1 2
PV Protect 1000-125 PV Protect 1000-125
Surge protection device for PV systems Surge protection device for PV systems
Description Compatibility
140
against electrical surges from the PV
187
215
140
ground connection. Dimensions 215 x 140 x 197 mm
[LxWxH] [8.6 x 5.5 x 7.8 in]
Net Weight 1.8 kg [3.9 lbs]
197
½ Provides enhanced protection Product name PV Protect 1000-125 ½ Wall mount using 4 holes with Mounting hole distances
187
to the pump controller from Ambient temperature -30°C to 50°C (-22°F to 120°F) weather protection. [WxH, Hole diameter]
215
incoming voltage surges Max. Voltage 1000 V DC ½ Designed for optional pole 160 x 150, Ø6 mm
½ Robust weatherproof housing mounting. Mounting points are [6.3 x 5.9, Ø0.236 in]
Max. current per string 125 A
designed to make installation pre-marked inside the housing.
Max. total current 125 A
simple
½ Tool required to open the housing Input cable size 10 - 35 mm² / AWG 8 - 2 197
½ Lockable for additional protection Output cable size 10 - 35 mm² / AWG 8 - 2
½ Correct grounding is required to Ground cable size ≥ 16 mm² / AWG 6 Order and Packaging information
make this device effective PG glands (input) 2 x PG16
½ Required for a professional Item number 19-001970
PG glands (output) 2 x PG16
installation of solar pumping Product name PV Protect 1000-125
PG gland GND 1 x PG16
systems Packed gross weight 2.4 kg [5.3 lbs]
Enclosure class IP 68
Packed volume 0.0125 m3 [0.44 ft3]
Housing material Polycarbonate
Packaging dimensions [LxWxH] 250 x 250 x 200 mm [9.8 x 9.8 x 7.8 in]
Approvals and standards EN 60204 - EN 61000 - EN 61643
1 2