Professional Documents
Culture Documents
MX4W Series
This is only for reference, the actual product does not support all combinations. ■ Input
Parameter 1
For selecting the specified model, follow the Autonics webstie. [MODE] 2 sec → [MODE] 3 sec →
• For using DC power, connect wires regardless of polarity. group
INSTRUCTION MANUAL
• Indicator model does not have the hold / zero terminal.
MX 4 W - ❶ - ❷ ❸ SOURCE [MODE] 4 sec →
Parameter 2
[MODE] 3 sec →
group
HOLD / ZERO 24 - 240 VACᜠ/ VDCᜡ
❶ Input type ❸ Preset output RUN [MODE] Parameter 0
→ [MODE] 3 sec → RUN
V: DC / AC voltage N: Indicator group
A: DC / AC current 1: NPN open collector 1 2 3 4 5 6 7 8 9 10
TCD210071AD [◀] + [▲] 3 sec → Zero adjustment Auto →
❷ Power supply 2: PNP open collector ①
F: 24 - 240 VACᜠ / VDCᜡ ② [MODE] + [◀] + [▲]
③ → Reset [MODE] →
5 sec
COM
Thank you for choosing our Autonics product.
Read and understand the instruction manual and manual thoroughly before Product Components MX4W-V-F□ MX4W-A-F□
± 500 mVDCᜡ / ± 200 mVDCᜡ /
using the product.
• Product • Instruction manual DC
± 50 mVDCᜡ
± 20 mA / 4 - 20 mA / ± 5 mA / ± 2 mA Parameter Setting
For your safety, read and follow the below safety considerations before using. ①
• Bracket × 2 • Terminal cover × 1 0 - 500 mVACᜠ / 0 - 200 mVACᜠ /
For your safety, read and follow the considerations written in the instruction AC 0 - 20 mA / 0 - 5 mA / 0 - 2 mA • Some parameters are activated / deactivated depending on the model or setting of
0 - 50 mVACᜠ
manual, other manuals and Autonics website. other parameters. Refer to the description of each parameter.
± 20 VDCᜡ / ± 5 VDCᜡ / 1 - 5 VDCᜡ / • If any key is not entered for 60 sec in each parameter, it returns to RUN mode.
Dimensions
Keep this instruction manual in a place where you can find easily. DC ± 500 mA / ± 200 mA / ± 50 mA
② ± 2 VDCᜡ • After returning to RUN mode, press the [MODE] key within 2 sec, it returns to
The specifications, dimensions, etc. are subject to change without notice for product AC 0 - 20 VACᜠ / 0 - 5 VACᜠ / 0 - 2 VACᜠ 0 - 500 mA / 0 - 200 mA / 0 - 50 mA previous parameter.
improvement. Some models may be discontinued without notice. • Unit: mm, For the detailed drawings, follow the Autonics website. • [MODE] key: Saves current setting value and moves to the next parameter.
DC ± 500 VDCᜡ / ± 200 VDCᜡ / ± 50 VDCᜡ ±5A/±2A [◀] key: Checks fixed value / Changes setting digits.
Follow Autonics website for the latest information. 91.5 ③ [▲] key: Changes setting values.
0 - 500 VACᜠ / 0 - 200 VACᜠ /
AC 0-5A/0-2A
0 - 110 VACᜠ / 0 - 50 VACᜠ
■ Parameter 1 group
Safety Considerations ■ Output Parameter Display Defaults Setting range
Display
condition
• 1: NPN open collector • 2: PNP open collector
• Observe all ‘Safety Considerations’ for safe and proper operation to avoid hazards. 96 4 20 1-1 Input type DC, -DC, AC -
1 2 3 4 1 2 3 4
DCAC DC
• symbol indicates caution due to special circumstances in which hazards may occur. 1-1 Input
type:
[MX4W-V-F□]
50)0
HOLD/ HOLD/ DC, AC
Warning Failure to follow instructions may result in serious injury or death. OUT1 OUT2 COM ZERO OUT1 OUT2 COM ZERO • Refer to Input Range and Display Range
1-1 Input
44.4
48
Input range type: -DC
-50)0
01. Fail-safe device must be installed when using the unit with machinery that 1-2
1-1 Input
01) IN-R
may cause serious injury or substantial economic loss. (e.g. nuclear power
control, medical equipment, ships, vehicles, railways, aircraft, combustion ■ Bracket ■ Panel cut-out Specifications %000
[MX4W-A-F□]
type:
DC, AC
• Refer to Input Range and Display Range
apparatus, safety equipment, crime / disaster prevention devices, etc.) 1-1 Input
4.9 ≥ 116 Model MX4W-V-F□ MX4W-A-F□ type: -DC
Failure to follow this instruction may result in personal injury, economic loss or fire.
-%000
02. Do not use the unit in the place where flammable / explosive / corrosive gas, 36 3 Input type DC / AC voltage DC / AC current *1-1 Input
high humidity, direct sunlight, radiant heat, vibration, impact or salinity Display STND: standard, SCAL: scale, type: AC
Max. allowable input Dependent on the input type 1-3
+0.6
may be present. method FREQ: frequency*, PF: power factor** **1-1 Input
DISP STND
45 0
+DC input ≈ -10 to 110 % F.S. for each measured input range type: ±DC
Failure to follow this instruction may result in explosion or fire.
22
≥ 52
03. Install on a device panel to use. -DC input ≈ -110 to 110 % F.S. for each measured input range 1-4 AVG, RMS
92 0 method type: AC
+0.8
Failure to follow this instruction may result in fire or electric shock.
IN-T RMS
AC input ≈ 10 to 110 % F.S. for each measured input range High-limit
04. Do not connect, repair, or inspect the unit while connected to a power source.
12-segment LCD 01) display value
Failure to follow this instruction may result in fire or electric shock. 1-5
gradient
!000 0.100 to 9.999 %
Display method - measurement value display part: white, character height: 19 mm 1-3
SPAN
05. Check ‘Connections’ before wiring.
■ Terminal cover - other display parts: red, green, yellow (indicator: white) correction Display
Failure to follow this instruction may result in fire. Low-limit method:
06. Do not disassemble or modify the unit. Display accuracy Dependent on the ambient temperature STND
display value
Failure to follow this instruction may result in fire or electric shock. 1-6 00 -99 to 99
15.5
23 ± 5 ℃ (DC input) ± 0.1 % F.S. rdg ± 2-digit ± 0.1 % F.S. rdg ± 2-digit 02) deviation
ZERO
93.7 15.9 correction
23 ± 5 ℃ (AC input) ± 0.3 % F.S. rdg ± 3-digit ± 0.3 % F.S. rdg ± 3-digit
Caution Failure to follow instructions may result in injury or product damage. 0 to 50 ℃ ± 0.5 % F.S. rdg ± 3-digit ± 0.5 % F.S. rdg ± 3-digit 03) Decimal
[DC / AC voltage model]
0, 0.0, 0.00, 0.000
00)0
1-7 point
Cautions during Wiring
Display cycle 0.2 to 5.0 sec (select per 0.1 sec) [DC / AC current model] 1-3
DOT
01. When connecting the power / measurement input and relay output, use position
Display scale -9999 to 9999 (4-digit) 0, 0.0, 0.00, 0.000 Display
)000
AWG 24 (0.20 mm2) to AWG 15 (1.65 mm2) cable or over and tighten the method:
1-8 High-limit scale H-SC - Display value against max. measurement input*
terminal screw with a tightening torque of 0.78 to 0.98 N m. • Unit: mm, Use terminals of size specified • Input and output are insulated from the A / D conversion method ΣΔ (Sigma Delta) analog-to-digital converter SCAL
below. power. 1-9 Low-limit scale L-SC - Display value against min. measurement input* &
Failure to follow this instruction may result in fire or malfunction due to contact Sampling cycle
failure. 50 ms High-limit * 1-7
Option output ADC input (DC input) Decimal
display value
02. Use the unit within the rated specifications. 1-10
gradient
!000 0.100 to 9.999 % point
and circuit and Power Sampling cycle
SPAN
Failure to follow this instruction may result in fire or product damage. hold / zero display part (AC input)
16.6 ms correction position:
03. Use a dry cloth to clean the unit, and do not use water or organic solvent. Low-limit 0.0, 0.00,
Failure to follow this instruction may result in fire or electric shock. 1 2 3 4 5 6 7 8 9 10 Resolution 1 / 20,000
display value 0.000
04. Keep the product away from metal chip, dust, and wire residue which flow Preset output NPN / PNP open collector output model 1-11 00 -99 to 99
≥3.0 deviation
ZERO
into the unit. ≤6.0 Load voltage ≤ 30 VDCᜡ correction 02)
Failure to follow this instruction may result in fire or product damage. [DC / AC voltage model]
Load current ≤ 100 mA Decimal 00)0
0, 0.0, 0.00, 0.000
NPN open collector output: ≤ 1 VDCᜡ / 1-12 point
[DC / AC current model]
DOT
Residual voltage position 03)
Cautions during Use PNP open collector output: ≤ 2 VDCᜡ 0, 0.0, 0.00, 0.000 1-3
)000
• Power supply should be insulated and limited voltage / current or Class 2, SELV power Certification ᜢᜧᜫ correction
supply device. Exponent of
01) W
hen using the unit at low temperature (below 0 ℃), display cycle is slow due to charateristics of LCD. Control 1-14 10-0 10-0: 100, 10-1: 10-1, 10-2: 10-2, 10 1: 101
• Install a power switch or circuit breaker in the easily accessible place for supplying or SPAN
eSPN
output operates normally.
disconnecting the power. 02) 5 A terminal: ± 0.3 % F.S. rdg ± 3-digit
1-15
High-limit
H-RG - Max. value of input range 1-3
• Keep away from high voltage lines or power lines to prevent inductive noise. 03) 5 A terminal: ± 1 % F.S. rdg ± 3-digit input value Display
In case installing power line and input signal line closely, use line filter or varistor at Low-limit method:
Power supply 24 - 240 VDCᜡ, 24 - 240 VACᜠ 50 / 60 Hz 1-16 L-RG - Min. value of input range PF
power line and shielded wire at input signal line. input value
Do not use near the equipment which generates strong magnetic force or high Permissible voltage range 90 to 110 % of rated voltage [DC / AC voltage model]
frequency noise. V, MV, OFF
V
Power consumption DC: ≤ 3 W, AC: ≤ 5 VA 1-17 Display unit -
Connection with the line filter Connection with the varistor [DC / AC current model]
dUNT
Insulation resistance ≥ 100 MΩ (500 VDCᜡ megger) A
A, MA, HZ, OFF
Install the line filter
close to the panel meter
Dielectric strength Between the charging part and the case: 3,000 VACᜠ 50 / 60 Hz for 1 min 01) W
hen changing input range, the following parameters are reset.
Panel meter - Parameter 1 group: display method, measurement method, decimal point position, high / low-limit scale, high-limit
Panel meter
HI Noise immunity ± 2 kV square wave noise (pulse width: 1 ㎲) by the noise simulator display value gradient correction, exponent of span, high / low-limit input value, display unit
HI 110 / 220 VACᜠ - Parameter 2 group: OUT1 / 2 output operation mode, OUT1 / 2 hysteresis
110 / 220 VACᜠ LOW 0.75 mm double amplitude at frequency of 10 to 55 Hz in each X, Y,
LOW Vibration - Parameter 0 group: OUT1 / 2 high-limit output setting value, OUT1 / 2 low-limit output setting value, max. / min. peak value
Z direction for 2 hours
02) L ow-limit display value deviation correction range is within -99 to 99 for D0, D-1 digit regardless of decimal point position.
Earth ground Vibration 0.5 mm double amplitude at frequency of 10 to 55 Hz in each X, Y, Z 03) Display
range is variable according to decimal point position.
(malfunction) direction for 10 min
• This unit may be used in the following environments. Dot Display range Frequency measurement range
- Indoors (in the environment condition rated in ‘Specifications’) Shock 300 m/s2 (≈ 30 G) in each X, Y, Z direction for 3 times -9999 to 9999 1 to 1200 Hz
- Altitude max. 2,000 m
0
Shock (malfunction) 100 m/s2 (≈ 10 G) in each X, Y, Z direction for 3 times -999.9 to 999.9 0.1 to 999.9 Hz
- Pollution degree 2
)0
Ambient temperature -10 to 50 ℃, storage: -20 to 60 ℃ (no freezing or condensation) -99.99 to 99.99 0.10 to 99.99 Hz
- Installation category II
)00
-9.999 to 9.999 0.100 to 9.999 Hz
Ambient humidity 35 to 85 %RH, storage: 35 to 85 %RH (no freezing or condensation)
)000
■ Parameter 2 group Input Range and Display Range ■ DC / AC current model (input type: DC) Output Operation Mode
Display When the max. input value is over the 100 %, it may result in input terminal damage. Display range Input • The below describes based on OUT1.
Parameter Display Defaults Setting range Input range
condition impedance
Diaplay method: STND (fixed) Diaplay method: SCAL 01)
• OUT1 and OUT2 of output operations are same. It operates individually by the set output
OUT1
[Preset output model]
■ DC / AC voltage model (input type: DC) 0.000 - 5.000 A 0.000 to 5.000
2-1 operation - operation mode.
OFF, HIGH, LOW, HL, HL-G
%000
Display range
OU!T OFF
mode Input range
Input 0.00 - 5.00 A 0.00 to 5.00 • When changing output operation mode, high-limit / low-limit output setting value, hysteresis
0.02 Ω
%00
Diaplay method: STND (fixed) Diaplay method: SCAL impedance
OUT2 0.000 - 2.000 A 0.000 to 2.000 are reset.
01)
Error
-2)0
LOW, HL, -20.0 - 20.0 VDCᜡ -20.0 to 20.0 -5.000 - 5.000 mA -5.000 to 5.000
OUT1 low-
)000
0 -9999 to 9999 162 kΩ
-2)0
21.87 Ω
-%000
0-2 limit output HL-G -5.000 - 5.000 VDCᜡ -5.000 to 5.000 -5.00 - 5.00 mA -5.00 to 5.00
)0 -999.9 to 999.9
OU!L -%000
setting value
-%00
1-1 Input -5.00 - 5.00 VDCᜡ -5.00 to 5.00 -2.000 - 2.000 mA -2.000 to 2.000 Error display is released automatically when it is in the measured and display range.
)00 -99.99 to 99.99
[DC / AC voltage & preset output model] type: -DC
-%00 -@000
-2.000 - 2.000 VDCᜡ -2.000 to 2.000 -2.00 - 2.00 mA -2.00 to 2.00 Display Description Troubleshooting
&
-50)0
)000 -9.999 to 9.999
-@000 -@00
2-1 OUT1 -2.00 - 2.00 VDCᜡ -2.00 to 2.00 01) C
onnect to the input terminals whose 30 % to 100 % of the input range includes the max. value of the input Flashes when measurement input is exceeded the
operation max. allowable input (110 %)
-@00
range to measure. Disconnect power supply
HHHH
-500.0 - 500.0 mVDCᜡ -500.0 to 500.0 When the max. input value is under the 30 % of the input terminal range, display accuracy is degraded.
mode:
Flashes when measurement input is exceeded the and check the cables.
-50)0
[DC / AC current & preset output model] LOW, HL, -500 - 500 mVDCᜡ -500 to 500
■ DC / AC current model (input type: AC)
-%000
min. allowable input (-DC: -110 % / DC, AC: -10 %)
-500
HL-G
LLLL
-200.0 - 200.0 mVDCᜡ -200.0 to 200.0
4 kΩ Flashes when measurement input is exceed the
-20)0
2-2 OUT2 -200 - 200 mVDCᜡ -200 to 200
Display range Input
OUT2 high- [DC / AC voltage & preset output model] operation Input range D-HH
max. display value (9999) Reset within the display
impedance
-200
Diaplay method: STND (fixed) Diaplay method: SCAL
50)0 01)
0-3 limit output mode: -50.00 - 50.00 mVDCᜡ -50.00 to 50.00 range.
Flashes when measurement input is exceed the
-5)00
0.000 - 5.000 A 0.000 to 5.000
OU@H
setting value [DC / AC current & preset output model] HIGH, HL, -50.0 - 50.0 mVDCᜡ -50.0 to 50.0 min. display value (-9999)
%000 D-LL
HL-G
%000 -5)0
01) Connect to the input terminals whose 30 % to 100 % of the input range includes the max. value of the input 0.00 - 5.00 A 0.00 to 5.00
0.02 Ω Flashes when input frequency is exceeded the
%00
1-1 Input range to measure. 0.000 - 2.000 A 0.000 to 2.000
When the max. input value is under the 30 % of the input terminal range, display accuracy is degraded. max. display value of measured range
F-HH
type:
@000
[DC / AC voltage & preset output model] DC, AC 0.00 - 2.00 A 0.00 to 2.00
Flashes when power factor display value to
■ DC / AC voltage model (input type: AC)
00)0
-
@00
& 0.0 - 500.0 mA 0.0 to 500.0
PF-H
measured input is over than LAG 0.50
2-2 OUT2
50)0
Display range Input 0 - 500 mA 0 to 500 Flashes when power factor display value to
operation Input range
500
Decimals Display range
impedance measured input is less than LEAD -0.50
[DC / AC current & preset output model] mode:
Diaplay method: STND (fixed) Diaplay method: SCAL 01)
0.0 - 200.0 mA 0.0 to 200.0
PF-L
LOW, HL, 0 -9999 to 9999 0.87 Ω
20)0
OUT2 low-
)000
0.0 - 500.0 VACᜠ 0.0 to 500.0 0 - 200 mA 0 to 200 Flashes twice when it exceeds zero range (±99)
0-4 limit output HL-G Reset within the zero range.
50)0
)0 -999.9 to 999.9 and returns to run mode
200
0 - 500 VACᜠ 0 to 500
OVER
0.00 - 50.00 mA 0.00 to 50.00
OU@L
setting value 1-1 Input
500
)00 -99.99 to 99.99
5)00
0.0 - 200.0 VACᜠ 0.0 to 200.0
[DC / AC voltage & preset output model] type: -DC
0.0 - 50.0 mA 0.0 to 50.0
4.062 MΩ
20)0
)000 -9.999 to 9.999
5)0
& 0 - 200 VACᜠ 0 to 200
-50)0
0.00 - 20.00 mA 0.00 to 20.00
2-2 OUT2
200 2)00
operation 0.0 - 110.0 VACᜠ 0.0 to 110.0 11)0 0.0 - 20.0 mA 0.0 to 20.0 2)0
mode: 0 - 110 VACᜠ 0 to 110 0.000 - 5.000 mA 0.000 to 5.000
[DC / AC current & preset output model] LOW, HL,
110
21.87 Ω
-%000 %000
0.00 - 50.00 VACᜠ 0.00 to 50.00 0.00 - 5.00 mA 0.00 to 5.00
HL-G
5)00 %00
0.0 - 50.0 VACᜠ 0.0 to 50.0 0.000 - 2.000 mA 0.000 to 2.000
2-1 OUT1 Decimals Display range
5)0 @000
operation 0.00 - 20.00 VACᜠ 0.00 to 20.00 0.00 - 2.00 mA 0.00 to 2.00
0 -9999 to 9999
2)00
mode:
@00
0.0 - 20.0 VACᜠ 0.0 to 20.0 01) C
onnect to the input terminals whose 30 % to 100 % of the input range includes the max. value of the input
except )0 -999.9 to 999.9 162 kΩ
2)0
Display max. 0.000 - 5.000 VACᜠ 0.000 to 5.000
range to measure.
0-5 Max. peak value in run mode OFF When the max. input value is under the 30 % of the input terminal range, display accuracy is degraded.
peak value 02) )00 -99.99 to 99.99
hPEK )0 %000
or 0.00 - 5.00 VACᜠ 0.00 to 5.00
2-2 OUT2 )000 -9.999 to 9.999
%00