ARAI The Automotive Research Association of Ini
atch Insite of the Automotive Industy with Ministry of Heavy Indust & Public Enterprises, Govt. of India)
Progress through Research
Confidential
DEVELOPMENTAL TEST REPORT
No. SHL/16/2019-2020/3100004972/DT/3068 DATE: 04.02.2020
1.0 [NAME AND ADDRESS OF THE | 3M India Ltd.
CUSTOMER Innovation Center, 48-51, Electronics City,
Bangalore - 560 100
2.0 | CUSTOMER LETTER REF Email dated: 13.08.2019
| 3.0 | DESCRIPTION OF TEST COMPONENTS AS DECLARED BY CUSTOMER:
Retro Reflective Raised Pavement Marker (RPM) (With shank) - Type 1
Color's: White, Yellow (Amber), Red
Marking on the sample: “3M”
Photograph Of Sample
White Yellow
4.0 | OBJECTIVE:
To carry out the following tests as per MoRTH Cl. no. 804
1. Coefficient of Luminance Intensity (MORTH Cl. no. 804.4.2, table no. 800-13)
2, Slope of Reflecting surface (Lens) (MoRTH Cl. no. 804.3)
3. Height of Marker (MoRTH Cl. no. 804.7.1)
4. Width of Marker (MoRTH Cl. no. 804.7.1)
5. Area of Retro Reflecting Surface (MoRTH Cl. no. 804.3)
6. Compressive Strength (MoRTH Cl. no. 804.2)
A Fe Page 1 of 5
ey
Progress through Reseach
HE AUTOMOTIVE RESEARCH
ASSOCIATION OF INDIA
Tan 80 900,130 TA007, 60 UPHAIGOIEC 27004 i
Reg Ofc: S.No, 12, Veta Mil, Paid Road, | Te: 4-206762 114, 3023 114 |ARAIWomologtion & Technology Cente (ARAFHTC), Chakan
Kothrud, Pune 41 038 nd, Fax :+91206762 104, 2023 104 ‘ARAI Forging industry Division (ARAV-ID),Chakan
PB No. 832, Pune 814008 inia) Email: erector@araina com, Website: ww aralndacom | ARAI Regional Cet South (ARALRCS), ChennalARAI
Progress through Research
DEVELOPMENTAL TEST REPORT No.: SHL/16/2019-2020/3100004972/DT/3068
5.0 | TEST RESULTS:
Please refer Test Results in 6.0 of this report.
5.1 | TEST DATES Test start date: 27.08.2019 Test End date: 11.12.2019
Disclaimer:
1. ARAL issues Test Reports / Extension Reports / Developmental Test Reports for vehicles! components! parts! assembles etc. based
‘on the documents preduced and/or prototype! vehicles) or sample(s) submitted by the applicant and testing thereot
2. ARAL issues Test Reports / Extension Repors / Developmental Test Reports in compliance to Motor Vehicle Act / Central Motor
Vehicles Rules and thei provisions as amended from time to time or any oter statutory orders under which ARAN 's authorized. Other
Rules! Acts are outside the purvew/ scope of Test Reporis / Extension Reports / Developmental Test Reports,
3, Testis) on protoype! vehicie(s) or samples) is/are carted out on the basis of standard procedures as notified under specific rules /
requested by the applicant. Results of such tests are the property of bearer of Test Reports / Extension Resorts / Developmental Test
Repos. These results cannot be disclosed unless speccaly so ordered by Government, Cour, et.
4. Unless otherwise supported by a separate Certificate, this Test Reports / Extension Reports / Developmental Test Reports shal not be
considered in isolation as valid Type Approval for any vehicle
5. ARAL is not responsible for testing each vehicles/ components parts! assemblies et. for which Test Reports / Extension Reports /
Developmental Test Reports is Issued. Further, ARAI is not responsible for ensuring manufacturing quality of the vehicles!
‘components/ pars/ assemblies etc. for which the Test Reports / Extension Reports! Developmental Test Reporsislare issued,
6, _ARAlis inno way responsible for any misuse or copying of any design/ type! system in connection with entre vehicle! components!
parts and assembies covered under the Test Reports / Extension Reports / Developmental Test Reports ieare issued
7. Breach of any statutory provision of Indian laws or laws of other countries, will be the sole responsiblity ofthe bearer of Test Reports /
Extension Repotts ! Developmental Test Reports is/are issued and ARAI shall not be lable for any claims or damages, The beater
shall alone be lable forthe same, and shall undertake to indernnify ARAL in ths regard
8 ARAI has the right but not under obligation to. frte, cancelation! withdrawal of the Test Reports J Extension Reports /
Developmental Test Reports isfare issued in case of aty Maud, misrepresentation, when it surlaces and comes in the knowledge of
ARAL
‘The appropriate local courts at Pune shall have the Jurisdiction in respect of any dispute, claim or llabilty arising out of this
certificate / Report.
PREPARED BY: CHECKED BY: APPROVED BY:
Ye ee \*
P.V. PARLIKAR Mrs. J. M. KIRVE ‘A.V. MANNIKAR
_ MANAGER: GENERAL MANAGER SR. DEPUTY DIRECTOR, HOD-SHL
| Place of Issue: PUNE Date of Issue: 4r2"20
ARA"
THE AUTOMOTIVE i. SZARCH
ASSOCIATION Cr INDIA
Page 2 of §ARA
Progress through Research
DEVELOPMENTAL TEST REPORT No.: SHL/16/2019-2020/3100004972/DT/3068
6.0 | TEST RESULTS: a
6.1 | Co-efficient of luminous intensity as per MoRTH Cl. no. 804.4.2, table no. 800-1
6.1.1 | For White colour Road stud with Shank
Measured Values (med/Ix)
Observation | Entrance | Minimum Required (Average of three samples)
angle (°) | Values (med/ix)
Side 4 Side 2
0 220 550.00 577.67
03 5 220 549.67 567.67
+5 220 538.67 566.67
0 120 376.00 446.00
05 =10 120 364,00 348.33,
_ +0 | 120 348.33, 344.33
6.1.2 | For Yellow colour Road stud with Shank
Measured Values (med/Ix)
Observation | Entrance | Minimum Required (Average of three samples)
angle (°) | angle (°) | Values (med/Ix)
Side 1 Side 2
0 110 404.00 380.33,
03 5 110 391.67 374.33,
. +5 1100 393.33 368.67
= 0 6 240.00 239.00
05 10 60 237.00 229.00
+10 60 231.00 227.33
6.1.3 | For Red colour Road stud with Shank
Measured Values (mediIx)
Observation | Entrance | Minimum Required (Average of three samples)
angle (°)_| angle (°) | Values (med/Ix)
Side 4 Side 2
0 44 447.17 141.57
03 44 149.97 142.63
+5 44 134.40 131.73
0 24 140.57 134.10
0.5 =10 24 127.40 119.13
+10 24 120.70 120.37
te
THE AUTOMOTI
ASSOCIATION Ce «
Page 3 of 5ARAI
Progress through Rosearch
DEVELOPMENTAL TEST REPORT No.: SHL/16/2019-2020/3100004972/DT/3068
6.2 | Area of Retro Reflecting Surface as per MORTH Cl. no. 804.3
Measured Angle
Remirornet White Yellow Red
The area of each retro reflecting surface shall 2 :
not be less than 13.0 cm? 16.04om? | 16.02cm? | 16.06 om’
6.3 Slope of Retro Reflecting Surface as per MORTH Cl. no. 804.3
Measured Angle
eoquirsenent White Yellow Red
The slope of retro reflecting surface shall 30° 30° 30°
preferably be 35 +5° to the base,
6.4 | Height of Marker as per MORTH Cl. no. 804,7.1
Measured Height
euenert White Yellow Red
‘Marker height shall not be less than 10 mm
‘and shall not exceed 20 mm, 15.90mm | 16.38mm | 15.82mm
6.5 | Width of Marker as per MoRTH Cl. no. 804.7.1
Requirement
Marker width shall not exceed 130 mm
Measured Width
Yellow Red
100.61 101.17
> «
89.17 89.64
Page 4 of 5
4
ASSOCIATION (ARAI
Progress through Research
DEVELOPMENTAL TEST REPORT No.: SHL/16/2019-2020/3100004972/DT/3068
66 | Compressive Strength as per MORTH Cl. no. 804.2
Test Requirements
When tested in accordance with 9.2.2, a marker shall support a load of 13636 kg
without breakage of significant deformation of the marker. Significant deformation
shall be understood to be 3.3 mm (0.13 in.)
Test Results & observations:
Marker with shank withstands the load of 13635 kgf without breakage.
Passed
TIE AUTOMOTIVE i: SEARCH
ASSOCIATION OF INDIA Ks
Page 5 of 5