STC-3008
Dual display two-way thermostat
Dual display two-way thermostat, Switch the modes between cool
‘and hest; Control tomporature by setting the tomperature eet value
‘and the diference value; Temperature calibration, Retigerating
Contral output delay protection; Alarm when temperature exceeds
temperature limit or when sensor error
Serr
Gout
Front panel size: 75(L)x24.6(W)(mm)
Mounting size: 71(L)¥20(ViN(eum)
Product size: 75(L)"34. 5(W)x85(D)(ram)
Sensor length: 1minclude theprobe)
Product Name: Dual display two-way thermostat
Housing material: ABS gray fame retardant molded case
Temperature measuring range:-55°O~120°C
Power supply: 110-220VAC=10%, 50/ 60Hz (or DG12V/Dc24V)
Accuracy: =1°C
‘Temperature measurement accuracy:0.1°C
Humidity measurement accuracy: 39%
Output cantrl: relay output
Output power: MAX 10A\
Sensor: NTC"2
Display instruction Six-digit LED+ Minus digit + Statue indieator
light(Status indicator ignt(7,2)+Set indicator light(Set))
Cemetery
Oi Long press A 3.seconds, the D group start temperature tosh
(default 25°C) press a ¥ to adjust long press ¥ 3 seconds, stop the
temperature value fash (default 40°C) press AV to adjust
@ Long press a 3 seconds, tne @ group star temperature fash
(detault28°C) press av to adjust, ong press Y 3 seconde, sip ne
temperature value fash (default 40%) press A¥ to adjust
Press A 4 button for 3 seconds atthe same time to enter he eating
mode, csplay PO, he fst group lemperaure delay, ross my
‘acjust, 0-60 minutes, defeut, afer adjustment, press singe Pt,
thesecond group tomporature Deiay, press adjust, 0-60
minutes, default 0, ater adusimert prose slace P2, nh
temperature alarm funcion, Default 120°C prese abajust,
adjust, press Ao enter P3, low temperature Alarm, default 85°C,
press AY to adjust, wait forthe second to eutomatcaly extress
"YY Seaconde to reset to factory satngs.
co
Meee)
(CASENISHERAG! control tho water heater, neat 0 65° C to stop,
the temperature drops back to 50" C and siaet heating again
Step 1: heating mode, starting temperature stop temperature
‘Stop 2: Prose and hold the" “button to start the temperature Fashing
Uso’a v "to aot th starting temperature to 30°C,
‘Stop 31ong press" " button 3 seconds to atop the tem
flashing. Uso" A ¥ "to set the stop temperature to 26°C. The setting
|= compiateat(meee (Ieee)
romero incon Noe
Rovio | @ Fetgopaenay conn raee
geen
tn rt | Seer ron cy Serta
seindcaorion | On pram etrg ate
Powers cegmaaone imac
Sima eee
‘Alarm when sensor error: Controller activate the sensor errr alarm
‘made when sensor open circuit or short circuit, all he running status
Is closed off wth the buzzer alarms, and the nixe tube dieplays"EE",
ross any key can cancel alarm ound, system back to alspiay the
‘normal temperature when tho orror end tho faults closred.
‘Alarm when the measuring temperature exceeds temperature
‘measuring range: Controller activates the error alarm function when
‘the mezsuting temperature exceeds the temperature measuring
range, all the running status is closed off with the buzzer alarms, and
‘mo nie tubo alsplaye"HH", Prose any Key can eancol alarm sound,
system back o diaplay the normal working mode when the
temperature restore to normal measuring range
Feet
“Danger
1 Strictly altingulah tne sencor down- oad, powor wire and output
relay intertace from one another, and prohibit wrong connections
or overloading the relay
2, Dangers: Proniit conneeting the wir terminals without
electricity cu-ot
Warning:
Prohibitusing the machine under the environmentf over damp. high
temp.. strong electromagnetism interference or trong corrosion
Notice
1. The power supaly should eonformto the voltage value indicated
‘nthe ietuction,
2. To avoid the interference, the sensor down-lead and power wire
‘should bokepta propor cletance.
Note: There is no voltage output from the output terminal of the
‘thermostat, So the device needs to be connected to a power supply