Professional Documents
Culture Documents
If you have just set up your new PC build or updating your old PC to a newer Windows version, you may need a bootable Pendrive
which has got the Windows Operating System on it. A USB boot is a process in which computer hardware can be enabled to get all
essential system booting information and files instead of a hard disk or a CD drive.
Table of Contents
This can be done using your own PC or other third-party utilities. Then the software will copy all the operating system files and boot the
sequence into the USB drive/pen drive to enable the USB boot. In order to create a bootable USB, you would need a USB drive/pen
drive with a minimum of 8 GB of storage.
3. Type “diskpart” and press enter. Doing this will open the windows inbuilt disk part utility which is used to manage the storage on
your computer. Now you have to wait until the DiskPart utility starts running.
4. In the new diskpart window, type “list disk” and hit Enter. It will display all the active disks present on your computer. Here, you will
see several disks.
5. Select the appropriate one based on the size of the disk. In our case, it is Disk 2.
Type “select disk 2” in the same window and hit Enter. You will now get a prompt “Disk 2 is now the selected disk” That means any
commands now will operate on Disk 2 directly.
6. Now, type “clean” and hit Enter to remove all of the data present in your USB drive. This command will completely format your
USB drive. Now, you will get a prompt “Diskpart succeeded in cleaning the disk”.
Note: The latest devices support UEFI non-CSM, however, if you are running it on an older device then your best bet will be to use
MBR.
Creating MBR Bootable USB Drive (The Easiest Way)
8. Type “create partition primary” and hit Enter. You will now get a prompt “DiskPart succeeded in creating the specified
partition.”
9. Type “select partition 1” and hit Enter. It will choose partition 1 for setting up it as an active partition.
10. Now, type “active” and hit Enter. It will activate the current partition for you to work on.
11. Now you have to type “format fs=ntfs quick” and hit Enter. This command will finally format your current partition as an NTFS
file system.
12. To exit, simply type “exit” and hit Enter. The command will close the DiskPart utility but not the CMD window.
13. Now that you have successfully formatted your USB Drive, It’s time to copy the data from the ISO Image present on your PC or a
DVD to your USB drive. Doing this will successfully turn your USB flash drive into a bootable Windows USB drive.
Creating GPT Bootable USB Drive (The Advanced Way)
8. Instead of a single partition to make an MBR bootable USB drive, here, you will need to create two partitions because natively
without supplying the NTFS drivers UEFI will not be able to use the NTFS partition. It can only recognize FAT32 natively.
Download the latest NTFS EFI Drivers from https://efi.akeo.ie/downloads/efifs-latest/. You will find four folders there namely “aa64”,
“arm”, “ia32” & “x64”. From each folder download the file starting with ntfs. We have downloaded the following files:
i) ntfs_x64.efi
ii) ntfs_ia32.efi
iii) ntfs_aa64.efi
iv) ntfs_arm.efi
In the partition 1 (64 MB), create a folder named “EFI” on the 64MB partition and inside that folder create another folder named
“Boot”. Copy the above-downloaded file in the folder.
13. To exit, simply type “exit” and hit Enter. The command will close the DiskPart utility but not the CMD window.
14. Now, copy all the content of the ISO image or DVD in the partition 2. You now have a GPT + UEFI (non-CSM) bootable USB
drive.
Installing Windows
Note: If you chose the GPT option in step 7, then make sure that secure boot is disabled. You can enable it once the installation of
windows is complete.
You have successfully copied the file contents of DVD into the USB drive and it is now bootable. In order to boot up a new computer,
follow these steps –
1. When your computer starts after powered on. Some function key (Generally F8/F12) is used to go into boot device selection. Just
make sure to insert the USB drive before powering on the computer and select your drive.
2. The other method which was traditionally used was to change the boot device order from the BIOS menu. For this, you will have to
go to bios settings and change the boot order. (See motherboard manufacturer website for more information.)
Final Words
Having a bootable USB drive for Windows is super convenient as these days, we don’t really opt for DVD and other options. And if
your PC doesn’t come with Windows preinstalled, or perhaps if you have set up your own system, setting up Windows shouldn’t be a
problem if you have got the bootable USB drive ready.
We hope our instructions are well stated and clear enough for you to follow. But in case any problem persists, please comment down
below and we’ll surely rectify it.