Professional Documents
Culture Documents
Stress Concentrations - How To Identify and Reduce Them in Your Designs
Stress Concentrations - How To Identify and Reduce Them in Your Designs
HWG / DESIGN /
In today’s world, products are getting increasingly complex, with downward pressure on overall
pricing. This has led to an inevitable increase in the geometric complexity of mechanical
components. While this has allowed components to perform multiple functions, it has led to
complex load transfers and possible concentrations of stresses.
A stress concentration is defined as a high localized stress, compared to the average stress of the
body, and is typically found in a region that has an abrupt geometric change. This article will walk
through the basics of a stress concentration, offer real-world examples to illustrate the concept,
and outline methods for reducing stress concentrations in your designs.
Stress concentrations are relatively straightforward when it comes to identifying where they will
be located and whether they have contributed to failure. They will be located in the small radii
and sharp corners that are in a load path. The image below shows a component that will have
rollers on the smaller diameter shafts on both ends, with a load applied to the top flat surface.
https://www.fictiv.com/hwg/design/stress-concentrations-how-to-identify-and-reduce-them-in-your-designs 1/11
06/06/2019 Stress Concentrations: How to Identify and Reduce Them in Your Designs | Fictiv - Hardware Guide
This setup will almost behave like skateboard trucks, but we’ll be loading to a higher force that is
cyclic in nature. The image below is a rendering of the subassembly that this component goes
into, including the rollers with bearings.
Now we can see that the smaller diameter shafts meet the center portion of our roller support
with a relatively abrupt radius. If we zoom in on this radius, we can see that it comes in at only
0.010”, as shown below.
https://www.fictiv.com/hwg/design/stress-concentrations-how-to-identify-and-reduce-them-in-your-designs 2/11
06/06/2019 Stress Concentrations: How to Identify and Reduce Them in Your Designs | Fictiv - Hardware Guide
If you recall from above, a sharp corner or radius will be the location of a stress concentration. In
order to visualize this stress concentration, I’ll run a FEA study that will plot out these stresses
quite well. The load case has already been discussed, but we can refer to the illustration below for
a refresher.
We have a downward force of 500 lbs, and we have fixed the surface of the shaft where the
rollers will sit. The only remaining step is to run the simulation and process our pretty pictures! In
the image below, we can see the beautiful red spots that indicate a stress concentration. That’s
it…it’s as simple as that!
We can see that this is the highest stressed feature, and this would be the first location to fail
under cyclic loading (though it would most likely occur on the bottom side loaded in tension,
instead of the top compressive side). It would initiate as a small surface crack that eventually
propagated through the component to complete failure.
There are also a few basic formulas to define the max stresses in this type of geometry when we
have a bending moment applied. The formula in this case is as follows:
σmax = kt*σave
Where:
https://www.fictiv.com/hwg/design/stress-concentrations-how-to-identify-and-reduce-them-in-your-designs 3/11
06/06/2019 Stress Concentrations: How to Identify and Reduce Them in Your Designs | Fictiv - Hardware Guide
In many simple geometries, the stress concentration factor is defined for a range of geometries.
The chart below shows the curves of these factors and the dependency on the ratios of the
critical dimensions.
This chart is used by dividing the large diameter by the smaller diameter first. So let’s say we have
a 2-inch diameter rod that is stepped down to 1 inch; that gives us a D/d of 2. Next, we look at the
ratio of the radius to the smaller diameter.
As another example, let’s say the radius is 0.1 inches, so we have a r/d ratio of 0.1. If we look at the
chart above, we need to find the curve that represents a D/d of 2. Then we look at the x-axis to
locate the r/d of 0.1 and look across to the Y axis to get a stress concentration factor of about 1.8.
https://www.fictiv.com/hwg/design/stress-concentrations-how-to-identify-and-reduce-them-in-your-designs 4/11
06/06/2019 Stress Concentrations: How to Identify and Reduce Them in Your Designs | Fictiv - Hardware Guide
It’s important to note that this formula changes based on the load case and geometry, so I
encourage you to further explore charts for additional geometries. Now that we understand the
basics, we can step into some examples of correcting stress concentrations.
Real-World Examples
In this section, we’ll look at a few real-world examples and how we can reduce the peak stresses
at the location of the stress concentration. The first example we’ll look at is our original
component with the rollers. If you recall, we had a very small 0.01” radius at the step-up in
diameters. Now, we’re going to increase that diameter to 0.08” to see how much we can reduce
the stresses.
The first image is the original stresses, and the second is the reduced stresses with the larger
radius.
https://www.fictiv.com/hwg/design/stress-concentrations-how-to-identify-and-reduce-them-in-your-designs 5/11
06/06/2019 Stress Concentrations: How to Identify and Reduce Them in Your Designs | Fictiv - Hardware Guide
We can see that the stresses have gone from 14,419 psi all the way down to 3,873 psi. While this
differential is pretty extreme because of the extremely small original radius, it drives the point
home of just how much a stress concentration can influence the stresses in the part.
In the next two examples, we’ll look at some geometries with a tensile load applied, instead of a
bending moment. The first part is a support bracket that holds a brass pin. The brass pin typically
has an upward load applied, and the base is bolted to a fixed plate, as shown in the setup image
below.
As you probably expected, we ran the FEA again to get a baseline stress value before making any
changes. The results of this study are shown below.
https://www.fictiv.com/hwg/design/stress-concentrations-how-to-identify-and-reduce-them-in-your-designs 6/11
06/06/2019 Stress Concentrations: How to Identify and Reduce Them in Your Designs | Fictiv - Hardware Guide
The stresses at the base with the small radii (0.030”) are definitely a high concentration, ranging all
the way above 68,0000 psi. By now, we can guess that a larger radius should help lower the
stresses here, even with a much different load case and geometry. In the next simulation, I have
increased the radii from 0.030” to 0.080”, and the results are much better, as shown below.
If I wanted to get even lower stresses, I could do so by thickening the flange to which this
assembly is attached. You can see the light blue coloring that gives an indication of how this part
is deflecting under a load.
In our next example, we have a flat plate with a diamond shaped hole cut out of the center. There
is a load applied on one end, while the other end is fixed, as shown in the setup below.
https://www.fictiv.com/hwg/design/stress-concentrations-how-to-identify-and-reduce-them-in-your-designs 7/11
06/06/2019 Stress Concentrations: How to Identify and Reduce Them in Your Designs | Fictiv - Hardware Guide
I’m sure by now you have guessed that the highest stresses will be located at the top and bottom
corners of the diamond shaped hole. If that is the case, you were absolutely correct. The next
image shows the results of this simulation.
We can see the stress concentration is exactly where we expected. We know we can make the
radii bigger, but what if we wanted the option of drilling that hole out, instead of requiring a mill
or punch? Can we use a larger diameter circle, effectively reducing the total material in the part,
and still lower the stresses?
Absolutely! As the image below details, the same simulation was run with a round hole that is
greater in diameter than the distance from the top to the bottom of the diamond-shaped hole
above.
https://www.fictiv.com/hwg/design/stress-concentrations-how-to-identify-and-reduce-them-in-your-designs 8/11
06/06/2019 Stress Concentrations: How to Identify and Reduce Them in Your Designs | Fictiv - Hardware Guide
We can see that while the stress region is larger, the magnitude of peak stress is roughly 1/3 of the
original case. In a similar approach but different application, it is common for repair centers to drill
a hole at the end of a crack to relieve the high stress concentration associated with the very small
radius at the tip of a crack.
I hope by now the idea of locating and reducing stress concentrations is clear, and you are well
on your way to improving a design. While I used an FEA program here to determine the
magnitude of stresses, there are some general guidelines that can be used to improve a design.
When it comes to common methods of reducing stresses, the following list includes some simple
items to get you started quickly:
Make radii in a load path as large as you are comfortable making them.
Limit the ratio of the large feature to the small feature, where possible.
Add stress-reducing holes at the end of slits, sharp angles, or cracks to relieve high stress
concentrations.
Refer to stress concentration charts to understand when you are in a region of diminishing
returns with respect to radius size.
https://www.fictiv.com/hwg/design/stress-concentrations-how-to-identify-and-reduce-them-in-your-designs 9/11
06/06/2019 Stress Concentrations: How to Identify and Reduce Them in Your Designs | Fictiv - Hardware Guide
Do not make a large size transition between loaded features. The stiffness mismatch will drive
the stress concentration much higher.
Don’t assume that the same size radius works for all features. Remember that the stress
concentration is based on a ratio, not a magnitude.
Don’t place a stress concentration in a high cyclic load if you absolutely must use a sharp
corner.
As you may have guessed, most of the “don’ts” are inverse to the “dos”. This list is not fully
comprehensive, but it should cover the basic concepts that every designer should know in order
to improve their design skills.
Through the examples and analysis above, it should be clear exactly why we need to be
concerned with stress concentrations. By incorporating these concepts through your design, you
should be able to achieve higher load ratings, reliability, and fatigue life.
I encourage design teams to talk through product requirements and design choices to ensure the
proper blend of aesthetics and function. There will always be tradeoffs, but proper analysis can
help achieve an optimized solution.
LAST PAGE
TRY IT TODAY.
GET A QUOTE
Materials
Design Guide
Urethane Casting
Materials
Service
Design Guide
Injecting Molding
Service
Capabilities
Design Guide
https://www.fictiv.com/hwg/design/stress-concentrations-how-to-identify-and-reduce-them-in-your-designs 11/11