Professional Documents
Culture Documents
5478064-1EN Rev7
5478064-1EN Rev7
gehealthcare.com
Technical
Publication
Direction 5478064-1EN
Revision 7
GE Healthcare
Precision THUNIS-800+ R&F System
Restricted Service Manual
Copyright © 2016
by General Electric Company, Inc.
GE HEALTHCARE
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ R&F SYSTEM RESTRICTED
Page 2
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
LEGAL NOTES
TRADEMARKS
Adobe, the Adobe logo, Acrobat, the Acrobat logo, Exchange, and PostScript are trademarks of
Adobe Systems Incorporated or its subsidiaries and may be registered in certain jurisdictions.
Microsoft is a registered trademark and Windows is a trademark of Microsoft Corporation.
All other products and their name brands are trademarks of their respective holders.
COPYRIGHTS
All Material, Copyright © 2013 by General Electric Company, Inc. All rights reserved.
警告 • 本维修手册仅提供英文版本。
(ZH-CN) • 如果维修服务提供商需要非英文版本,客户需自行提供翻译服务。
• 未详细阅读和完全理解本维修手册之前,不得进行维修。
• 忽略本警告可能对维修人员,操作员或患者造成触电、机械伤害或其他形式
的伤害。
警告 • このサービスマニュアルには英語版しかありません。
(JA) ・ サービスを担当される業者が英語以外の言語を要求される場合、翻訳作業
はその業者の責任で行うものとさせていただきます。
・ このサービスマニュアルを熟読し理解せずに、装置のサービスを行わない
でください。
・ この警告に従わない場合、サービスを担当される方、操作員あるいは患者
さんが、感電や機械的又はその他の危険により負傷する可能性があります。
IMPORTANT...X-RAY PROTECTION
X-ray equipment if not properly used may cause injury. Accordingly, the instructions herein
contained should be thoroughly read and understood by everyone who will use the equipment
before you attempt to place this equipment in operation. The General Electric Company, Healthcare
Group, will be glad to assist and cooperate in placing this equipment in use.
Although this apparatus incorporates a high degree of protection against x-radiation other than the
useful beam, no practical design of equipment can provide complete protection. Nor can any
practical design compel the operator to take adequate precautions to prevent the possibility of any
persons carelessly exposing themselves or others to radiation.
It is important that anyone having anything to do with x-radiation be properly trained and fully
acquainted with the recommendations of the National Council on Radiation Protection and
Measurements as published in NCRP Reports available from NCRP Publications, 7910 Woodmont
Avenue, Room 1016, Bethesda, Maryland 20814, and of the International Commission on
Radiation Protection, and of any other local authorities, and take adequate steps to protect against
injury.
The equipment is sold with the understanding that the General Electric Company, Healthcare
Group, its agents, and representatives have no responsibility for injury or damage which may result
from improper use of the equipment.
Various protective materials and devices are available. It is urged that such materials or devices be used.
Revision History
Revision Date Reason for change
1 May. 4, 2013 First release
2 Jul. 1, 2013 Update the installation pictures in Physical Installation.
Update SCH picture in MIS Map & Schematics.
Update installation procedures in Renewal Parts.
Update procedures in Periodic Maintenance.
3 Oct. 21, 2013 Update x-ray tube installation and tube cover.
Remove fuse installation, update console installation and
schematics
4 Jun. 23, 2014 Update renewal parts.
Remove windows xp standard installation steps, only keep ghost
steps for system recovery.
Add torque requirement for collimator installation at P72.
Add steps for how to exit DSA at P243.
Add explanation for "X-Ray No. <->Patient ID" button at P233.
Remove all CE descriptions at P16 & P126.
Add adjustment steps for FRU 5458529 at P384.
Add ferrite installation steps of Generator at P82.
Add part numbers for accessories and optional parts.
5 Jul. 18, 2014 Add CE descriptions & DICOM troubleshooting.
6 Nov.18, 2015
7 Aug. 26, 2016 Remove all CE descriptions at P126.
Preface
Publication Conventions
Standardized conventions for representing information is a uniform way of communicating
information to a reader in a consistent manner. Conventions are used so that the reader can easily
recognize the actions or decisions that must be made. There are a number of character and
paragraph styles used in this publication to accomplish this task. Please become familiar with them
before proceeding forward.
It’s important that you read and understand hazard statements, and not just ignore them.
Section 1.0
Safety & Hazard Information
Proper product safety labeling allows a person to safely use or service a product. The format and
style for safety communications reflected in this publication represents the harmonization of IEC/
ISO 3864 and ANSI Z535 standards.
Within this publication, different paragraph and character styles are used to indicated potential
hazards. Paragraph prefixes, such as hazard, caution, danger and warning, are used to identify
important safety information. Text (Hazard) styles are applied to the paragraph contents that are
applicable to each specific safety statement.
Preface Page 15
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
NOTICE - Indicates information or a company policy that relates directly or indirectly to the
safety of personnel or protection of property. This signal word is associated directly with a
hazard or hazardous situation and is used in place of 'DANGER,' 'WARNING,' or 'CAUTION.'
It can include:
• Destruction of a disk drive
• Potential for internal mechanical damage, such as to a X-ray tube
Some parts inside are live even after the system is shut down, make sure to open the MAINS
switch in the power distribution box on the wall and follow LOTO procedure.
Page 16 Preface
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
Section 2.0
Publication Conventions
2.1 General Paragraph and Character Styles
Prefixes are used to highlight important non-safety related information. Paragraph prefixes (such
as Purpose, Example, Comment or Note) are used to identify important but non-safety related
information. Text styles are also applied to text within each paragraph modified by the specific
prefix.
The current section and its title The current chapter and its title
are always shown in the footer of are always shown in the footer of
the left (even) page. the right (odd) page.
An exclamation point in a triangle is used Paragraphs preceeded by a symbol
to indicate important information to the user. (e.g. bullets) contain information that
Paragraphs preceeded by Alphanumeric has no specific order.
characters (e.g. numbers) contain infor-
mation that must be followed in a specific order.
Headers and footers in this publication are designed to allow you to quickly identify your location.
The document part number and revision number appears in every header on every page. Odd
numbered page footers indicate the current chapter, its title and current page number. Even page
footers show the current section and its title, as well as the current page number.
Preface Page 17
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
2.3 Computer Screen Output/Input Text Character Styles
Within this publication, mono-spaced character styles (fonts) are used to indicate computer text
that’s either screen input and output. Mono-spaced fonts, such courier, are used to indicated text
direction. When you type at your keyboard, you are generating computer input. Occasionally you
will see the math operator “greater-than” and “less-than” symbols used to indicate the start and
finish of variable output. When reading text generated by the computer, you are reading it as
computer generated output. In addition to direction, characters are italicized (e.g. italics) to indicate
information specific to your system or site.
Example: This paragraph’s font represents computer generated screen “fixed” output.
Fixed Output Its output is fixed from the sense that it does not vary from application
to application. It’s the most commonly used style used to indicate
filenames, paths and text that do not change from system to system. The
character style used is a fixed width such as courier.
Example: This paragraph’s font represents computer screen output that is
Variable Output “variable”. It’s used to represent output that varies from application to
application or system to system. Variable output is sometimes found placed
between greater-than and less-than operators for clarification. For
example: <variable_ouput> or <3.45.120.3>. In both cases, the < and >
operators are not part of the actual input.
Example: This paragraph’s font represents fixed input. It’s computer input that is
Fixed Input typed-in via the keyboard. Typed input that does not vary from application
to application or system to system. Fixed text the user is required to
supply as input. For example: cd /usr/3p
Example: This paragraph’s font represents computer input that can vary from
Variable Input application to application or system to system. With variable text, the
user is required to supply system dependent input or information. Variable
input sometimes is placed between greater-than and less-than operators.
For example: <variable_input>. In these cases, the (<>) operators would
be dropped prior to input. For example: ypcat hosts | grep <3.45.120.3>
would be typed into the computer as
ypcat hosts | grep 3.45.120.3
without the greater-than and less-than operators.
2.4 Buttons, Switches and Keyboard Inputs (Hard & Soft Keys)
Different character styles are used to indicate actions requiring the reader to press either a hard or
soft button, switch or key. Physical hardware, such as buttons and switches, are called hard keys
because they are hard wired or mechanical in nature. A keyboard or on/off switch would be a hard
key. Software or computer generated buttons are called soft keys because they are software
generated. Software driven menu buttons are an example of such keys. Soft and hard keys are
represented differently in this publication.
Example: A power switch ON/OFF or a keyboard key like ENTER is indicated by applying a character style
Hard Keys that uses both over and under-lined bold text that is bold. This is a hard key.
Example: Whereas the computer MENU button that you would click with your mouse or touch with your hand
Soft Keys uses over and under-lined regular text. This is a soft key.
Page 18 Preface
GE HEALTHCARE
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
Table of Contents
Preface
Publication Conventions ...................................................................................... 15
Section 1.0
Safety & Hazard Information ........................................................................... 15
1.1 Hazard Messages............................................................................................................ 15
1.2 Text Format of Signal Words ........................................................................................... 15
1.3 Symbols and Pictorials Used ........................................................................................... 16
Section 2.0
Publication Conventions ................................................................................. 17
2.1 General Paragraph and Character Styles........................................................................ 17
2.2 Page Layout..................................................................................................................... 17
2.3 Computer Screen Output/Input Text Character Styles .................................................... 18
2.4 Buttons, Switches and Keyboard Inputs (Hard & Soft Keys) ........................................... 18
Section 1.0
Introduction
The goal of this document is to guide the service representative through an entire X-ray room
installation.
The following On-site Requirements must be accounted for prior to beginning installation of the
system.
Section 2.0
Objective and Scope of this Manual
This direction will lead you in a correct sequence through the manuals needed to install the
equipment. Following the suggested sequence will result in an orderly installation. However,
extenuating circumstances may dictate a deviation from the recommended sequence. Feel free to
deviate, but keep track of your progress by checking off the tasks in the flowchart as you complete
them.
Check equipment according to the packing list for your system against the main catalog numbers
in the FDO (Field Delivery Order). Also, verify that all the manuals are present in the binders
according to the Table of Contents.
Before starting to install the system, identify all the cables and check their length to verify that they
are long enough. If you find a short cable, contact us immediately so we can send the required
length cable to you and thereby, not delay the installation.
2.3 Interconnection
Interconnection of products by furnished cables or contractor supplied wiring is indicated by
numbered MIS runs in the installation sections. Run interconnect charts are available, which
describe the connection and function of each wire.
2.4 Presentation
The procedures in this steering manual are presented in job card forms.
Section 3.0
On-Site Requirements
3.1 Tools and Test Equipment
There are no additional tools and test equipment besides the listed tools which must be available
before installing the Precision THUNIS-800+ R&F System as below.
• Electric hammer drill with bits
• Digital multimeter
• 4 Ft. Level (or two standard levels)
• Torque wrench
• HV cable removal spanner
• Push-pull Gauge
• Silicone grease
• Common service tools
• Resolution Pattern
• Dose Meter
• Power cable
• Crane (Part#5440337)
• M12 hexagon bar wrench
• M8 Wrench for I.I. installation
3.2 Documentation
Directions are necessary for correct installation of the Precision THUNIS-800+ R&F System.
Procedures from each document will be used and reflect the latest information available at this time.
Not all procedures in this manual apply to all sites. Before you begin installation, cross out the
procedures that do not apply to your site.
Section 4.0
Description of System
7
X-Ray Tube
Collimator
5
4
Table
3 Console
PDU
Section 5.0
Installation Process
See System Installation Road map & Applied Time Standards on the next page.
Start
Complete Pre- 2 person 2 person 2 person Complete
Crane readiness Install PDU 1 person
/ŶƐƚĂůůĂƟon 4 hours 0.5 hours 2 hours MI==>FE Handoī 0.5 hours
Receive and 2 person Install PosiƟoner 2 person Install Integrated Equipment and
2 person 1 person
Inventory System 4 hours Table 5 hours console Personnel
3 hours 0.5 hours
Install Generator 2 person Electrical 2 person System Checks 1 person
Cabinet 3 hours ConneĐƟons 0.25 hours 3 hours
GE EXCLUSIVE USE ONLY
Done
DAY 1 16 hours DAY 2 17 hours DAY 3 15 hours DAY 4 8 hours
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
Page 34
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
Section 1.0
System Installation Guide
1.1 Mechanical Installation
6 Attach Warning Labels and Rating Plates People Required: 1 Hours to Complete: 0.5
Attach all the warning labels and detent markers.
Section 2.0
Installation Handoff Checklist
Pre-Installation Checklist
Delivery Date: Sales Person:
Equipment:
2.) Floor is strong enough for intended equipment and mounting methods
approved – seismic regulatory codes considered?
8.) Support structures installed for floor and wall mounted equipment?
Interconnections Completed
4.) Flexible, stranded wire provided for System input power connection?
5.) System “feeder” power cables pulled and sufficient length available at
disconnect box for connections?
General Completed
Comments:
Inspection Date(s):
11.) List of any installation drawing deviations (all deviations should be signed by customer
and reviewed by the installation specialist).
12.) Packing materials disposed of.
13.) The crane returned.
____________________________________ ____________________________________
Mechanical Installer Signature Field Engineer Signature
____________________________________ ____________________________________
Mechanical Installer Signature Field Engineer Signature
Section 3.0
Cables
3.1 Routing
• System MIS cables should be pulled to/from the System Cabinet before the System Cabinet
is moved into the final mounting position.
• Some system cables are pre-connected to a sub-system and should not be disconnected in
order to pull the cable(s) through the conduits or wall ducts.
• Power cables must be kept separate from signal cables as much as possible. In wall ducts or
raceway, power cables should be routed in a separate channel from signal cables. Inside
system cabinets, power cables should not be bundled together with signal cables.
All MIS cables should be routed through the conduits or wall ducts as rate-proofed as possible.
Section 4.0
Positioner Table
4.1 Unpack
This section will describe the basic steps required to un-crate the table.
• Do not discard any packing materials such as envelopes, boxes, bags until all parts are
accounted for against the packing list.
• Check the mechanical conditions and external appearances of all parts for possible damages
or missing items.
• The distribution center or factory must be notified immediately of any damage or shortage of
parts.
1.) Remove the top cover and four top cross members from the table shipping crate.
2.) Remove any additional cross members from the inside of the crate.
3.) Remove the sides of the shipping container. See Figure 2-4.
7.) Unpack the unfixed dolly from one of the fixed dollies.
2.) Adjust dolly bolts to raise the table base level. See Figure 2-12.
Note: Make sure the table base raised at least 7 centimeters above.
DO NOT put your feet under the table base, for the table is so heavy and may hurt you.
2.) Install the digital spot device, and secure it with the four screws.
Note: Adjust the position of digital spot device, place along marked guidelines, and then tighten the
four screws.
2.) Divide the cables into two groups for installation (one group is for I.I., the other is for other
subsystems behind the tube stand).
Lift the Tube Stand Align Tube Stand with Spot Device
Figure 2-27 Install Tube Stand
Page 52 Section 4.0 - Positioner Table
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
2.) Loosen the four motor mount screws to adjust the motor belt tension.
Edge of
Mark on the motor plate
Supporting plate
J14
5458763
8.) Connect a temporary power cable.
Note: Apply AC220V at power input terminals on the Electrical Base.
Note: Please connect the temporary power cable to TM1-3(220V), TM1-5(0V) and GND.
If the country DO NOT have AC220V, please tilt table manually.
Note: Make sure the table tilting direction is controlled by the correct buttons on key board, i.e. table
clockwise direction tilting is controlled by table clockwise rotation button, etc.
Tilt the table LESS THAN 90 degrees to avoid the table’s overturn.
3.) Adjust the tube stand height to facilitate the I.I. mounting by pressing the upward/downward
buttons on the key board.
4.) Power off.
5.) Disconnect the temporary power cable.
Demount Screws
Front
Cover
Bottom
Cover
7.) Fix the cable to the Image Head using the cable clamp. Place the ferrite close to the cable
clamp before tightening.
Note: Pay attention to the direction of tube rotation detent. The direction of the detent should be the
same as X-ray beam.
Note: To avoid damaging the switch, make sure the tube x-ray window is away from the switch when
placing the tube to holder.
4.) Install X-ray tube onto the tube holder.
Mount and rotate the tube to proper position Remove the protective plastic blocks
Note: Make sure the tube window is away from the switch when placing the tube to holder, and then
rotate the tube to proper position. Hold the tube to prevent it falling down.
5.8N.m
8.) Install the cooling fan with cable (5450222) and X-Ray tube angulation cables.
Note: Pay attention to the air flow direction of tube fan.
11.) Clean HV cable connectors, and then apply a thin layer of silicon compound.
12.) Connect the anode and cathode HV cables to the X-ray tube.
Note: Check the polarity of HV cables carefully, and DO NOT connect the two HV cables reversely.
13.) Adjust tube to the position easy for operation.
Figure 2-57 Connect cables for cooling fan & tube tilt unlock button
6.) Connect collimator cables, and fix them with cable clamps.
8.) If the 4 collimator adjusting screws are loose, keep screws tightening.
To avoid the risk of electric shock, this equipment must only be connected to a supply with
protective earth.
Section 5.0
Generator Cabinet
5.1 Unpack
• Do not discard any packing materials such as envelopes, boxes, bags until all parts are
accounted for against the packing list.
• Check the mechanical conditions and external appearances of all parts for possible damages
or missing items.
• The distribution center or factory must be notified immediately of any damage or shortage of
parts.
1.) Remove the top and side covers of the shipping container and cross braces.
Demount
6.) Connect the anode and cathode HV cables to the generator oil tank.
HV Tank HV Cable
+ +
- -
Note: Check the polarity of HV cables carefully, and do not connect the two HV cables reversely.
5445938
To prevent possible body or equipment damage, please avoid inappropriate power up.
11.) Connect PCU generator I/F cable (5450388) and touch screen console communication cable
(5123315) on generator I/F board.
b.) Connect touch screen grounding cable (5124835) from touch screen to generator room I/
F board.
c.) Connect generator room I/F cable (5462260).
d.) Connect door lock (TB 4, 5) and room light (TB 11, 12) on TB4.
AEC Channel 1
AEC Channel 2
14.) Ty-rap the cables and remount all the generator cable protective covers.
Section 6.0
PDU Cabinet
6.1 Unpack
• Do not discard any packing materials such as envelopes, boxes, bags until all parts are
accounted for against the packing list.
• Check the mechanical conditions and external appearances of all parts for possible damages
or missing items.
• The distribution center or factory must be notified immediately of any damage or shortage of
parts.
1.) Remove the top and side covers of the shipping container and cross braces.
5.) Position PDU cabinet to the location that does not prevent the table’s movement.
Section 7.0
Integrated Console
7.1 Unpack
• Do not discard any packing materials such as envelopes, boxes, bags until all parts are
accounted for against the packing list.
• Check the mechanical conditions and external appearances of all parts for possible damages
or missing items.
• The distribution center or factory must be notified immediately of any damage or shortage of
parts.
1.) Remove the top and side covers of the shipping container and cross braces.
Demount Demount
Demount
Note: Follow the process below during installing the 20 m cable (5122285) on PCU side.
At PCU side, the shielded cable should make 3 paths in the ferrite (2 loops).
a.) Open the ferrite and place the cable inside. The length of cable between the ferrite and
the connector shall be about 7 cm.
f.) Connect the cable to PCU. Follow the instructions below to secure the cable connector
with PCU.
Put the ferrite under the PCU
Bind cables
Finished cables
Power
4
4
6
6
2
2
Key 3
Key 3
1
1
5
5
COM1
Keyboard
Mouse
Rockey Hospital Network
COM2
Primary Monitor Inroom Monitor (Option)
Section 8.0
Electrical Connections
1.) Please configure Jumper J14 on Table Board 5458763 back to Pin2-Pin3 connection.
1 2 3
0 1 1
2.) Configure the Dipswitch S1, S2 to default (S1(1-4)=Off, Off, Off, Off; S2(1-4)=Off, Off, Off, Off).
J431
J442
J531
J542
J432
Section 9.0
Accessories
9.1 Install Compressor (Part#5476931)
1.) Take out the compressor with a dowel and bolt.
2.) Insert the dowel into the pole of the compressor.
Note: Align the holes in the dowel and pole.
2.) Insert the two latter fixing pins into the slots in both side rails.
Note: Install the footrest by customer's requirements.
3.) Install the inboard compression band pole (the pole without compression band fixed on), adjust
the compression band pole to a proper position.
To release/loosen the compression band, pull the handle towards table top. A "Tick" sound will
be heard.
5.) Pull the compression band to the inboard compression band pole through patients, and insert
the pole through the compression band.
Section 10.0
DAP Meter Installation (Optional)
1.) Unpack the box of DAP Meter.
2.) Place the display at the upper-right of the console desk, then fix the screw.
Rotate collimator to insert the chamber Fix the screw to lock the chamber
through the rails at the bottom of collimator
Connect the cable with chamber Connect the cable with display
5.) Connect the power adapter to the socket on the back of console table.
6.) Insert the other end of adapter into the power interface of display to power on the device.
Section 11.0
Wall Stand Installation (Optional) (Part#5477035)
11.1 Unpacking
• Do not discard any packing materials such as envelopes, boxes, bags until all parts are
accounted for against the packing list.
• Check the mechanical conditions and external appearances of all parts for possible damages
or missing items.
• The distribution center or factory must be notified immediately of any damage or shortage of
parts.
1.) Loosen all the 6 fibulaes, and remove the top and sides of shipping containers together. See
Figure.
11.2 Installation
1.) Refer to the room layout in Pre-Installation Manual (5442442-1EN), and confirm the location
of the wall stand with the operator. Move wall stand to the location.
Note: Use the ruler to measure the distance between the two sides of front panel with collimator to
make sure the x-ray beam is perpendicular to wall stand front panel.
4.) If the requirements above cannot be met, adjust wall stand location or the four leveling bolts.
and then go to step 8 for wall stand fixing.
1. Loose the screw on the tube top Move the tube to 40 degrees towards outside
2. Press and hold the buttons on the tube handle
6.) Move the wall stand to make sure the SID at 1.8 m. Then open the collimator light, make sure
that the bias between the cross hair projected by the collimator and the cross hair in the wall
stand front panel is less than 3 mm in two orthogonal directions.
Note: When the collimator blades are closed to one line, it should be overlapped with the wall stand
cross hair.
Note: Use the ruler to measure the distance between the two sides of front panel with collimator to
make sure the x-ray beam is perpendicular to wall stand front panel.
7.) If the requirements above cannot be met, adjust wall stand location.
8.) Drill two holes through the two holes on wall stand base, and clean holes of all dust and chips.
Note: Please use 10 drill.
9.) Insert the supplied two M10 anchors and washers, and hammer the anchors into the holes.
11.4 Grid
1.) Demount the wall stand front panel.
Section 12.0
Final Cover Installation
Note: Install the subsystem covers after system checks and configuration/calibration.
PN#5500982
Note: Before securing the HV cables, make sure the sufficient cable length for tube rotation.
4.) Fix the cables at the back of tube stand.
Please move the tube to 150cm SID when fixing the cables to make sure the sufficient cable
length for tube stand movement. The cable distance between the two brackets on the back of
tube stand should be more than 110cm.
Point 3
Point 2
Point 1
Point 1 Point 2
2.) Install generator cabinet top cover with two ground cables.
Note: Leave at least 20 cm between console cabinet and wall, or the high temperature in console
cabinet will damage the server.
After the physical installation, please secure the PDU and console cabinet by locking the brakes.
Section 13.0
Fix Table
Note: Confirm the location of table with customers before fixing the table.
1.) Drill four 14 mm diameter holes 120 mm deep with masonry drill.
Section 14.0
Labels and Rating Plates
Attach multilingual labels to overlay the Chinese labels attached in factory.
14.1 Table
Figure 2-176
14.3 PDU
Watchdog
DICOM
DSA
Section 15.0
MI ==> FE Handoff Checklist
Purpose: Mechanical Installer to Field Engineer handoff checklist to confirm that all critical
installation steps have been completed.
3.) Cable shield clamps installed and tightened (how many, where).
4.) All mounting bolts installed and tightened (floor and wall).
Section 16.0
FE==> Apps Handoff Checklist
Purpose: Field Engineer to Application Specialist handoff checklist to confirm that all critical
installation steps have been completed.
Section 17.0
Final Steps
17.1 Database Backup
After calibration, perform complete database backup. Refer to Backup procedure in the Utilities
appendix (See Software Backup / Restore on page 246.).
Section 1.0
General
Check system functions after system installation.
If any problems happen during system checks, please refer to - Troubleshooting on page 293.. And
then, please do system checks from the beginning again.
After system checks, install the covers.
Section 2.0
Checking Steps
2.1 CHECK THE OUTSIDE AND THE WIRINGS
b.) Check the red light is illuminated on generator interface board (Troubleshooting -
Generator on page 306.)
3.) System power up: Check all the indications (refer to LED INDICATORS on page 317.)
d.) Console interface board lights up (Troubleshooting - Console I/F Board on page 326.)
f.) Door lock check: The x-ray exposure is prohibited when the door is open.
g.) Room light check: Check the red light is illuminated on the exam room when doing x-ray
exposure.
i.) DSA runs (Troubleshooting - No Image Acquisition with X-ray Exposure on page 335.)
1.) Select above table mode (receptor 3) or under table mode (receptor 4) .
2.) Press located on the left-bottom of the touch screen frame to check the anode
running.
3.) Take exposure.
4.) Conditioning / Seasoning by referring to Chapter 3.1 - Tube Conditioning / Seasoning.
frame .
If replace or operate the static electricity parts, make sure the FE must take the ESD protection
action.
Section 1.0
Hardware
1.1 Table
S3 CONFIGURATION
Dipswitch S3 Function
S3(1) ON: 9 inch II
OFF: 12 inch II
If the customer select In room foot pedal (Option). There is a configuration for customer to
select:
1.) S3(4) = OFF: (Default - Remote configuration) Console foot switch and In-room foot switch are
controlled by “Remote” button. They can't be activated at the same time during fluoroscopy
operation.
2.) S3(4) = ON: (Customer - Classical configuration) Console foot switch and In-room foot switch
are not controlled by “Remote” button. They can be activated at the same time during
fluoroscopy operation.
Page 146 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
J14 CONFIGURATION
Jumper Jumper
Before installation, set Jumper J14 to Pin1-Pin2 connection, and after installation, set it back
to the default (Disconnect Pin1-Pin2).
Page 148 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1.2.2 Intercom board configuration
A196 Tube
SW1: 1~8 OFF
Page 150 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1.3.4 ABC Jumper Setting
On generator I/F board, the jumpers have to be set to:
Note: 1.) There are many ABC inputs on generator I/F board; PT800+ shall use J8, which is a BNC
connector.
2.) For some jumpers, such as JW11, JW19 and JW21, there are 3 pins named 1,2,3. So PINs 2-
3 means pin 2 and 3 shall be connected.
Jumper
PINs 1-2 means pin 1 and pin 2 shall be connected.As shown below.
Jumper
Jumpers locate
on this board
Note: 1.) Some jumpers are simple jumpers, such as JW2 and JW3...etc. There are only 2 pins for these
jumpers. ON means connect, OFF means not connected.
2.) Some jumpers are a little bit complex, for example, JW44. 45, 46. There are only 4 pins for 3
jumpers. The figure below shows how to set these jumpers.
JW45 OFF
JW44 ON JW45 ON JW44 OFF JW46 ON JW44 OFF
JW46 OFF
JW45 OFF
JW46 OFF
Pin1 Pin2 Pin3 Pin4 Pin1 Pin2 Pin3 Pin4 Pin1 Pin2 Pin3 Pin4
3.) The figures above are just illustration to show the usage of this kind of jumpers. The marks on
the board have to be carefully read to ensure correct jumper setting. JW49, 50, 54,55,59,60
are nearly the same.
Page 152 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1.4 PDU Configuration
Factory configured voltage is 380V. You should configure the voltage by jumpers on the
transformer according to the local power requirement.
The level-stop limit switch must be fixed with correct position, measured by the angle
instrument.
1.) Tilting the table with anti-clockwise, when the motion being stopped by the level-stop limit,
holding this tilting position.
2.) Power down the system.
3.) Connect the two angle LCM calibration branches which is belong to the J351 and J42 on table
logic board respectively.
4.) Power on the system, and hold on at least 2 seconds, then angle LCM will display 0 degree.
5.) After calibrate successfully, power down the system, and disconnect the calibration branches.
Page 154 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1.7 Collimator FOV Calibration
Also use an accurate ruler to measure the FOV size on the collimator window.
4.) Power on, Make the Collimator Controller of Positioner Console on max position, and push the
key switch of “Remote Manual” (S10) on console, and the “Remote Manual” should be lit.
5.) Push the lamp button of Collimator to light it. Adjust Potentiometer of Table board (5458763)
to control the collimator FOV.
6.) For 12 inch image intensifier, need to adjust 3 FOV sizes (12 inch, 9 inch, 6 inch) as below
steps shown:
- Mag1 (12inch) FOV: Adjust the potentiometer R53 and R132 for 12 inch II to make the
field of lighting on the tool to match the corresponding edge (12 inch II=64mm). The
adjustment specifications as the figure below. Tolerance=+/-1mm. Then press down
SID150cm button on console to store adjusting data into the E2prom on Table board,
and the buzzer on table board will tweet, meanwhile hold on the potentiometer’s
adjustment on table board.
Note: For potentiometer R53 and R132 adjustment:
Clockwise direction stands for FOV decrease, counter-clockwise stands for FOV increase.
- Mag2 (9inch) FOV: Adjust controlling blade on console to make the field of lighting on
the tool to match the corresponding edge (9 inch =47mm). The adjustment specifications
as the figure below. Tolerance=+/-1mm. Then press down SID120cm button on console
to store adjusting data into the E2prom on Table board, and the buzzer on table board will
tweet.
- Mag3 (6inch) FOV: Adjust controlling blade on console to make the field of lighting on
the tool to match the corresponding edge (6 inch =35mm). The adjustment specifications
as the figure below. Tolerance=+/-1mm. Then press down SID105cm button on console
to store adjusting data into the E2prom on Table board, and the buzzer on table board will
tweet.
7.) For 9 inch image intensifier, need to adjust 1 FOV size (9 inch) as below step shown:
- 9 inch II FOV: Adjust the potentiometer R53 and R132 for 12 inch image intensifier to
make the field of lighting on the tool to match the corresponding edge (9 inch image
intensifier =47mm). The adjustment specifications as the figure below. Tolerance=+/-
1mm. Then press down SID150cm button on console to store adjusting data into the
E2prom on Table board, and the buzzer on table board will tweet, meanwhile hold on the
potentiometer’s adjustment on table board.
12 Inch II 35mm
9 Inch II
6 Inch II
35mm
47mm
64mm
Page 156 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
Section 2.0
Software
Note: All the installation drivers are stored in E:\Setup\. The files E:\Setup\SYSBAK.GHO and
E:\Setup\SYSBA001.GHS cannot be moved.
All the factory configured parameters are stored in D:\Service Tools\. If you do any modifications on
the parameters, please also store in this path as another file name. DO NOT replace the factory
configured file.
All the software are factory installed.
If necessary, do recovery with the recovery disk which includes Operating System, Service
Package, Drivers (PCI1750 Card, Grablink Value and other drivers).
After the recovery, please refer to 2.4 - Service Tools & 2.5 - DSA to install Service tools (GenWare,
TH8740, and Image Brightness Measure tool), DSA software and Rocky driver.
Suggest recovering system with the recovery disk if necessary.
Below software versions are for examples. Please confirm the current software versions in your
system by referring to the CDs shipped with system.
Note: The touch screen membrane can be easily scratched by sharp objects. To avoid possible damage,
items such as pens, pointers, tools, and etc should not be brought near the touch screen
membrane.
Do not attempt to install unauthorized software onto the console. The generator must be
programmed not to exceed the x-ray tube maximum operating limits shown in the Operator Manual
(Part Number 5445574-1EN). Intended life and reliability will not be obtained unless generators are
operated within published specifications.
The viewing angle adjustment screws at the rear of the touch screen console should only be
removed by qualified personnel. Removing these screws may create instability, causing possible
equipment damage or personal injury. The screws may be loosened sufficiently by the user to
adjust the viewing angle of the display, but must be retightened immediately.
The X-ray generator on / off buttons are located on the lower-left of the touch screen frame.
The touch screen console will power up when the generator is switched on. When the console has
completed its startup routine, the main console menu will appear on the touch screen console.
Three menu selections are available as described below.
The software on the USB will damage a desktop PC. The software must be installed on a CPI Touch
Screen computer only.
After a brief delay, the system utilities menu will be displayed. The message Access
Denied indicates that an incorrect password was used.
The factory-default password may be changed by a service engineer as described
later. If this was done, the password defined above will not allow access to the
system utilities menu.
* APR Editor Allows the APR to be edited. Changes may be saved to memory.
* APR Backup / Allows the APR data to be backed up, and backed-up APR data to
Restore be restored. The factory-default APR data is available in several
languages.
* Date / Time Allows the date and time to be set or changed.
Setup
* Receptor Allows predefined receptor symbols to be assigned to each image
Symbols receptor button.
* Touch Screen • Allows for the setting of specific console operating
Setup parameters.
• Sets up the serial communication ports on the touch screen
console.
• Allows adjustment of the sound volume.
• Enables / disables compatible equipment (i.e. infimed digital
interface).
• Allows the operator and service passwords to be changed.
* Touch Screen Allows for electrical alignment of the touch sensitive membrane
Calibration with the “buttons” displayed on the touch screen.
* Data Link Prepares the console for communication with an external
computer. This is a service tool intended for use by authorized
service personnel only.
- Main Menu Return to the main console menu.
Note: It is strongly suggested that you review the operator manual (5445574-1EN) before proceeding. A
good understanding of the terminology and APR menu structures is needed to make APR changes.
Note: When a region of interest (i.e. SKULL) is selected, a pop-up menu will appear similar to that in
normal APR mode. In addition to “new” ADD, EDIT, and DELETE buttons, a MOVE UP and
MOVE DOWN button will be displayed.
The MOVE UP and MOVE DOWN buttons allow the items in a menu or submenu to be
rearranged. To do this, select the item to be moved. This will highlight the item. Press MOVE
UP to move the selected item up in the list, and MOVE DOWN to move the selected item down
in the list.
Note: When editing or adding an APR item, menu item, or procedural item, an English keyboard will
pop up at the bottom of the screen. A partial keyboard with international symbols may be
displayed at the top of the screen. To display the desired international characters, select the
Be aware of the generator and x-ray tube limits when setting the parameters. Failure to do so
may cause a limit error when the edited procedure is chosen on the touch screen.
1.) Opening the APR Editor from PC will show an image similar to the one below.
2.) Holding the mouse over any “Item“ will show a pop-up window containing the same
information as in the “Properties“ panel but in a more concise way as shown below.
b.) After the pop up info show up click the item again.
5.) Use the Properties panel on the left hand side of the APR Editor to modify the parameters for
each item and /or procedure.
6.) Select the parameter value to modify on the Properties panel and double click it. A drop down
box will be displayed containing a range of values available for the selected parameter. Notice
that only the items parameters values can be modified. Menus and procedures do not contain
any parameters.
7.) Changing from small to large Focus, for the pediatric size patient of the Skull Townes item.
a.) Select the Skull Townes item.
1 2 3
4 5 6
The current image receptor symbols may be replaced with predefined symbols chosen from the
receptor symbol library.
Each image receptor button will always select a predefined image receptor (i.e. table Bucky, wall
Bucky, DR, etc.). Before changing the image receptor symbols, it must be clearly understood which
image receptors are selected by each image receptor button. Each image receptor button should
then have a logical and intuitive symbol assigned to that position.
1.) From the system utilities menu, press Receptor Symbols.
2.) A pop-up window will display as above showing the image receptor buttons with the currently
assigned symbols near the right side of the receptor symbols window, and the library of
available receptor symbols near the left side of the window.
3.) Select the image receptor button for which the symbol is to be changed. The receptor numbers
in the figure above correspond to the receptor numbers.
4.) Select an appropriate symbol for the selected receptor from the symbols library.
5.) Press to assign the selected symbol to the selected image receptor button.
6.) Repeat steps 3 and 5 for each image receptor whose symbol is to be changed.
7.) Press OK to continue or CANCEL to return to the system utilities menu without making any
changes. If OK was pressed, a pop-up window will display asking if you wish to save the
changes. Press YES to save the changes. Press NO to return to the system utilities menu;
CANCEL cancels the changes.
- Press .
- A pop-up window will display asking if you wish to delete the selected item. Press YES to
delete the item; NO cancels the deletion.
- DO NOT DELETE SYMBOLS YOU MAY WANT TO USE IN THE FUTURE.
Settings
1.) Program the functions defined in the table above by checking or un-checking the applicable
item.
2.) Program the Digital Port to COM1. This selects the communication port for the optional digital
interface i.e. the InfiMed imaging system.
3.) Program the DAP Port. Use default.
4.) Program the Data Link Port to COM2.
5.) Program the Languages. This selects the language for operator and error messages, and for
text on the buttons, etc. Voice messages may only be available in English.
6.) Select the Generator Type as Indico 100.
7.) Set the Screen Saver Interval as OFF. This sets the time from the last activity on the touch
screen until the screen saver is activated.
Features
1.) From the touch screen setup window, select FEATURES. Available digital interfaces will be
shown on the screen.
2.) Check GE Hualun Digital Interface to enable the function.
3.) Press OK to continue or CANCEL to return to the system utilities menu without making any
changes. If OK is pressed, a pop-up window will display asking if you wish to save the
changes. Press YES to save the changes. Press NO to return to the system utilities menu;
CANCEL cancels the changes.
Passwords
Be sure to record the new service password before changing the factory-default password. If
the new password is subsequently lost, consult the factory or re-install the touch screen
software in order to restore the factory-default service password.
6.) To change the service password, press the ... button to the right of the top service password
line. A password window will pop up. Enter the new password.
- Press Clear to cancel an incorrect entry.
- Press Cancel to close the password pop-up window.
- Press Accept to accept the new password.
7.) Repeat the previous step to enter the new password on the second service password line.
8.) Press OK to continue; CANCEL cancels the changes.
9.) A pop-up window will display asking if you wish to save the changes. Press YES to save the
changes. Press NO to return to the system utilities menu; CANCEL cancels the changes.
Error Logs
The error logs function records console errors only. This screen exists for CPI debugging purposes.
The information recorded will generally be of no value to field-service personnel.
- If the calibration was done properly, you will be taken to the main menu.
- If the calibration in steps 4 and 5 was not done properly, it will not be possible to press
the center of the targets in this step. The calibration program will run again, allowing you
to redo the touch screen calibration.
2.2 Recovery
If necessary, do recovery with the recovery disk which includes Operating System, Service
Package, Drivers (PCI1750 Card, Grablink Value and other drivers).
After the recovery, please refer to 2.4 - Service Tools & 2.5 - DSA to install Service tools (GenWare,
TH8740, and Image Brightness Measure tool), DSA software and Rocky driver.
Suggest recovering system with the recovery disk if necessary.
1.) Insert the recovery disk into the CD-ROM, and close the CD-ROM and reboot the workstation.
2.) When a time counter appears on the left-top corner, press “enter” key to start the recovery
process. At the same time, there will be a click sound from the PC speaker.
4.) A dialog pops up during the recovery process, just press the “Enter” key to continue.
5.) Waiting, after recovery finishes, system will reboot automatically. When the click sound
appears, reject the recovery disk from CD-ROM and then press any key to boot from the hard
disk, or do nothing until the sound disappears to boot from the hard disk.
6.) If reboot successfully, the desktop of Windows XP appears.
8.) The "Display Properties" window pops up, select "Themes", and select "Windows XP" in the
“Theme” list.And then click “OK”.
10.) Select the third tab in “Regional and Language Options” and select the compatible language
in the “Select a language to match the language version of the non-Unicode program you want
to use“.
3.) The "nView Desktop Manager" window pops up, select "Hot Keys" tab, set parameters as
below in the popup window.
a.) The PC system maybe halt after you finish installing the driver of mother board chipset,
and if the system halts, please cool reset the PC by pressing the power switch in the front
of the PC machine box.
b.) The screen will flash for several times between the step 5 and step 6 of the display
adapter driver installation and the Grab card driver installation, you should ignore it.
6.) Select the checkbox, and click "Finish" to restart the computer.
7.) Ignore all the popup message boxes after finishing the reboot.
5.) After successfully installing the network connection driver, a hint message will appear in the
task tray on the bottom-right corner of the screen if the cable is linked correctly.
5.) Use the default folders and existing folders, and click "Next".
7.) After finishing Grab setup, wait until a popup wizard appears to show that system finds a new
hardware, run the wizard step by step, select the "Recommanded" item, and click "Next".
5.) After finishing the driver installation, right-click "My Computer" on the desktop, and select
"Properties" to enter the "System Properties" window.
8.) Click "Update Driver..." to update the driver for the PCI1750 card, the process is just the same
as the Grab setup step 7 to step 9.
7.) Use the default "Program Folders" and "Existing Folders", and click "Next".
2.4.1 Genware
2.4.1.1 Installation
1.) Insert Genware Installation Disc and get into the path F:\GenWare32, or install from
E:\Setup\ServiceTool\CPI\GenWare32\.
10.) Wait until installation completes, and then, the following window pops up. GenWare installation
has completed.
3.) Click “COM“ button to set “COM2“. Use COM2 to link GenWare communication to Touch
Screen.
Note: The RED color text and button on GenWare User Interface will be displayed to BLACK color.
Ignore it. You can still click them on corresponding position.
2.4.2.1 Installation
1.) Run “TH8740_122_Setup.exe“ from F:\PCUControlSoftware in IQ Tools CD, or from
E:\Setup\ServiceTool\.
Note: To ensure the PCU parameters be set correctly, when do ABC or AEC calibration, TH8740
should be run firstly, and then run DSA.
“Alt”+”Tab“ key are used to switch the program windows.
2.4.3.1 Installation
1.) Run “ImageBrightnessMeasure.exe“ from F:\ImageBrightnessMeasure.exe in IQ Tools CD, or
from E:\Setup\ServiceTool\.
2.5.2 Uninstallation
If a system recovery process has been followed according to 2.2 - Recovery, there is no DSA
software installed, please refer to 2.5.3 - Installation to install the DSA software.
English/Chinese version of DSA software is factory installed. You should uninstall the English/
Chinese version, and install the English/Local Language version.
The installation steps for English/Local language version are the same as English/Chinese
version. This manual uses English/Chinese version as example.
4.) Select "Phother DSA Digital System 8", and click "Remove".
6.) After remove DSA from control panel, go to regedit to remove DSA completely.
7.) Run “regedit“ from “Start -> Run“.
2.) Accept the terms in the license agreement", and click "Next".
2.) Input “hrml“ in the popup a window as password, and click "OK".
6.) Select "Apply DSA" check-box to activate DSA if ROCKEY has not been activated yet, input
the Serial Number.
Note: If customer order DSA (Optional), please get the letter from customer, open it, input the serial
number, and activate DSA.
If DSA is activated before, the serial number of DSA has already stored in the ROCKEY, so
DO NOT click “Apply DSA“ during re-installation.
If DICOM is activated before, the serial number of DICOM has already stored in the ROCKEY,
so DO NOT click “Apply DICOM” during re-installation.
The default selection is “X-Ray No. <-> Patient ID [0010,0020]”, that means the DSA will use
system “X-Ray No.” as the “Patient ID” value embedded in DICOM to send images to PACS
system or printer system.
If the second one “Patient ID <-> Patient ID [0010,0020]” selected, DSA will use system
“Patient ID” as the “Patient ID” value embedded in DICOM to send images to PACS or printer
system.
If the second one selected, then system “Patient ID” from RIS will be the same as the “Patient
ID” sent to the PACS.
8.) Click "Reversion" to restore the patient database, select the version customer needs and press
"Reversion" in the popup "Database Reversion" dialog, and then, the computer will restart.
2.) Input “hrml“ in the popup a window as password, and click "OK".
8.) Re-start the computer. If DSA software is auto log on, the configuration is completed.
2.) Input all the correct information of the PACS server supplied by hospital in the "Dcm Store
SCU" popup window, and then, click "Verify" to test the network connection.
7.) The "Settings" window will popup. Set the parameters as operators requirements in “Print
Scheme Setup“ tab.
8.) Input all the correct information of the DICOM Printer supplied by hospital in the "Server Setup"
tab, and then, click "Verify" to test the network connection. If the connection is ok, select the
"Add as Default" checkbox, click "add" to add the printer. And then, the DICOM printer
configuration is finished.
Only GE Healthcare engineers are allowed to know the above key combination. Do not tell your
clients so as not to bring unnecessary consequences.
Place an object whose size is known on the table, open the collimator and do exposure to get
image. Click A, and move the mouse to the starting point of the examined object and single click it.
And move the mouse to the end point, then single click. Pull out a straight line, which is the length
of the target object, and its value appears in window A. Single click “Scale“ to pop up a calibration
window. Enter the actual size of the target object, with the default unit being in mm. Single click
“Confirm“ to go back. The value in window A changes.
2.) Choose the “Real time filter” and dis-selected the “Sharpen”.
3.) .Restart the system and check the “Sharpen” button is dis-selected.
Patient’s information can’t display normally while initiating Black-White inversion of image. To
enable the shutter, Periphery of images will not be inversion during initiating Black-White inversion
of image, so that the patient’s information can be display normally. The default setting for Shutter
is “Disable“, Following steps show how to enable Shutter function,
1.) Click Acquisition parameters setting button, a Password window will be displayed (No
password input required). Click “OK” button to access Acquisition configuration window..
2.) Select “Shutter” tab and input the diameter (about 910), then click “Enable” button.
1.) Click “Start -> Programs -> GenWare Utilities -> GenWare Generator Utilities” to run GenWare
Generator Utilities.
2.) Backup generator parameters.
a.) Click “Utility -> Backup Generator to File”.
b.) Select the location you prefer to save the backups, give a name (such as “Generator
Parameters“), and then, click “Save“. Suggest to save the backup file to D:\Service Tools\.
b.) Restore the factory configured backed-up file from D:\Service Tools\.
Note: Check the settings after downloading the parameters as below.Setup -> Tube Selection
A196
6.) To upload an APR file from a USB flash disk to the touch screen select the desired file (ex.
PS800+English-V01.apr) from the USB Device window and press . Once the file is
copied successfully, it will appear in the Touch Screen window of the USB File Transfer Utility.
7.) Using this way, upload all APRs to touch screen.
8.) When finished, press Close to exit to window “APR Backup and Restore”.
9.) Delete the original APRs of touch screen. Such as “ENGLISH.APR”
10.) Restore “PS800+English.apr” as current APR.
11.) When finished, press Close to exit and go to main screen.
Section 3.0
Image Quality
3.1 Tube Conditioning / Seasoning
Tube conditioning or “seasoning” is particularly important for new tubes or tubes that have not been
used for several days. This should be performed on each X-ray tube before attempting auto
calibration, as an unseasoned tube may not operate properly at higher kV values without arcing.
Note: Close the collimator blades and put a folded Lead Apron on the table-top to protect I.I tube.
Select “Receptor 3“or “Receptor 4“before tube conditioning / seasoning.
3.1.1 Overview
The generator does X-ray tube auto calibration at 50 kV, 60 kV, 70 kV, 80 kV, 100 kV and 120 kV.
The tube normally needs to be seasoned before it can be operated at the higher voltages
encountered during auto calibration.
Tube seasoning is started by auto calibrating the kV stations up to and including part of the 70 kV
station. The tube is then seasoned at 70 kV. Progressively higher kV stations are then auto
calibrated and seasoned. Finally the entire kV and mA range is auto calibrated, then the tube is
seasoned at the remaining high kV values.
Manually releasing the exposure button during auto calibration of a particular kV station in the
following procedure prevents the generator from attempting operation beyond that kV/mA value.
Note: Low speed only exposures are recommended for the seasoning exposures, to prevent excessive
heat build-up in the housing from the stator windings or the rotor bearings.
3.1.2 Procedure
Note: X-ray tube seasoning should be done on LARGE focus in order to minimize tube wear. And then,
SMALL focus.
1.) Run Genware Generator Utilities software, and open Setup -> Auto Tube Calibration.
Note: The procedure below is intended for seasoning an X-ray tube prior to attempting tube auto
calibration. To season a tube that does not need to be calibrated, simply follow steps b, d, f, h,
and i.
a.) Start the tube auto calibration sequence, and manually terminate the exposure at 70 kV
and 250 mA.
b.) Season the tube at 70 kV by taking approximately 10 exposures of 200 mA and 100 ms.
These exposures should be taken at the rate of approximately one every 15 seconds.
c.) Restart the auto calibration sequence and manually terminate the exposure at 100 kV and
250 mA.
d.) Season the tube at 100 kV by taking approximately 5 exposures of 200 mA and 100 ms.
These exposures should be taken at the rate of approximately one every 15 seconds
e.) Restart the auto calibration sequence and manually terminate the exposure at 120 kV and
160 mA.
f.) Season the tube at 120 kV by taking approximately 5 exposures of 160 mA and 100 ms.
These exposures should be taken at the rate of approximately one every 15 seconds.
g.) Restart the auto calibration sequence and allow the auto calibration sequence to
complete.
h.) Season the tube at 130 kV by taking approximately 5 exposures of 100 mA and 50 ms.
These exposures should be taken at the rate of approximately one every 15 seconds.
i.) Repeat step 8 at 140 kV, and then at 145 kV.
3.) Do the calibration of SMALL focus by repeating the above steps.
The way to get KV and mA data by manual mode is for ABS mode adjustment.
3.) Set KV to 125KV and mA to 4.7mA (refer Dose Rate Adjustment Procedure).
4.) Step down the Fluoro pedal, read the Dosimeter value as A, and then judge if this test value
is valid by this formula: A*N*(1+M+1%) <= 9.9R/Min.
If valid, the value of mA is valid and no need do dose rate adjustment.
If invalid, do dose rate adjustment:
1.) Need to do dose rate adjustment (do the mA limitation adjustment in ABS Limits table to
reduce the dose rate) according to procedure of dose rate adjustment for Fluoro.
2.) To reduce the mA limit and do this step again.
KV mA
40 6.0
50 6.0
60 6.0
70 6.0
80 6.0
90 6.0
100 6.0
110 5.8
120 5.0
125 4.7
KV mA
40 6.0
50 6.0
60 6.0
70 6.0
80 5.2
90 4.2
100 3.5
110 2.9
120 2.6
125 2.4
b1
b2
a2
X-ray Field
If pass, it’s ok. If fail, please adjust collimator lamp, and redo alignment of visually defined x-
ray fields until pass.
PCU
Generator
J8
Gen I/F bd
J4 Co-axis cable
10.) On PT800+ workstation, Run Image brightness measure software by double click
“ImageBrightnessMeasure.exe”. A dialog will be popup. Move this dialog to left-top corner of
the monitor so that it doesn't cover the image.
11.) Make sure DSA software is running.
Note: Make sure that WW/WL is the default value 4096/2048 during the ABS calibration process.
12.) Click keyboard “Alt”+”Tab” to switch DSA as current program. Take fluoro, and stop after
image is stable.
13.) Click button “Measure” on Brightness Measure Software, read the value displayed on edit box
“Average Brightness”.
14.) Check if the average brightness level is between 35 +/- 3.
15.) Adjust both Iris and Head value on PCU setup software and repeat step 11 to 13 until the
average brightness level is 35 +/- 3.
Both Iris and Head can change the image brightness. The strategy is:
- Adjust Iris first based on head = 3.
- Iris proper range shall be 80 to 130. If the image brightness is still not within required
target even if Iris has been adjusted to 80 (or 130), Head value shall be adjusted.
- The proper Head value shall be 1-4.
Note: During this process, gamma config shall be gamma configuration number = 7.
16.) Change Gamma config to 0, 1, 3 and take fluoro again, Verify that the image is in good
brightness.
Note: Gamma Config 0: Mid Contrast; Gamma Config 1: Low Contrast; Gamma Config 3: High
Contrast.
Note: • Min fluoro voltage shall be set to 40kV, this is a PPP requirement.
• Max fluoro voltage shall be set to 125kV.
• Fluoro ABS default = ON. It means when CPI touch screen started, fluoro ABS state is ON.
• II mode is 0 means there is only one II mag mode in Precision THUNIS-800+ system.
• Fluoro/Rad kV Def shall be set to Curve 2.
• Fluoro timer Mode shall be set to 10 minutes.
• HLF selection, PF selection shall be set to Console.
• SID compensation shall be un-checked.
23.) Click menu “setup->fluoro setup”.
24.) On “fluoro ABS curves” page, enable 3 curves and type in following data.
80 2.1 3.8 6
90 3.1 5 6
100 4.3 6 6
110 5.7 6 6
120 6 6 6
125 6 6 6
25.) Make sure the default parameters on "fluoro ABS" page are as picture below.
26.) On Genware, set fluoro mode to ABS, and set "ABS curve" to MED.
Note: LOW stands for ABS curve1. MED stands for ABS curve2. HI stands for ABS curve3.
27.) Take fluoro, Keep modifying Level2 value and Signal Gain on Fluoro ABS page until the fluoro
parameters are: 68kV, 2.3mA.
Both Level 2 and signal gain works for ABC loop. The calibrate strategy is:
- Set Signal gain to 5, then adjust Level 2 voltage between 0 and 5;
- The proper Level2 voltage shall be 2.5 to 4.0.
- If the fluoro parameters cannot reach 68kV, 2.3mA even if Level2 voltage has been
adjusted to <= 2.5 or (>= 4.0), change Signal gain.
- The proper range for signal gain is between 2 to 10. Most frequently used value is 5 or 6.
MED curve in Normal Mag (12 inch) configuration is Done.
45.) For 9 inch II configuration, it only have one MAG pre-set the KV=72KV,mA=2.8mA and ABS
curve =Med
46.) Pre-Set the CCD mode
Set CCD operation mode config 12 to:
- CCD mode = 8;
- Syc mode = 0;
- ABC/AEC conf = 1;
- Head = 3;
- AGC = OFF (uncheck)
- IRIS = 125
- Neural filter = OFF(uncheck)
47.) Repeat the step 7 - Step 15
48.) Adjust both Iris and Head value on PCU control software and repeat step 11 to 13 until the
average grey level is 35 +/- 3.
Both Iris and Head can change the image brightness. The strategy is:
- Adjust Iris first based on head =3.
- Iris proper range shall be 100 to 150. If the image brightness is still not within required
target even if Iris has been adjusted to 100(or150), Head value shall be adjusted.
- The proper Head value shall be 1 - 4.
Note that during this process, gamma config shall be gamma configuration number = 7.
49.) Change Gamma config to 0, 1, 3, and take fluoro again, Verify that the image is in good
brightness.
50.) Repeat step 17- step 26
51.) Take fluoro, Keep modifying Level2 value and Signal Gain on Fluoro ABS page until the fluoro
parameters are: 72kV, 2.8mA.
Both Level 2 and signal gain works for ABC loop. The calibrate strategy is:
- Set Signal gain to 5,then adjust Level 2 voltage between 0 and 5;
- The proper Level1 voltage shall be 2.5 to 4.0.
- If the fluoro parameters cannot reach 72kV, 2.8mA even if Level1 voltage has been
adjusted to <=2.5 or (>=4.0), change Signal gain.
- The proper range for signal gain is between 2 to 10. Most frequently used value is 5 or 6.
Configuration Action
0 12inch II, Normal Mag Fluoro IRIS=105 Head Gain= 3,without NDF
AEC Channel 1
AEC Channel 2
15.) Connect test PC to PCU through RS232 cable. Run PCU control software on test PC.
17.) Select Gamma config 7, confirm the Gamma configuration 7 set as “type” to “parametric”. Set
gamma = 1, then click apply.
Or Just select an existing gamma = 1 configuration. Make sure that B/W inversion is not
checked.
18.) On PT800+ workstation, Run Image brightness measure software by double click
"ImageBrightnessMeasure.exe". A dialog will be popup. Move this dialog to left-top corner of
the monitor so that it doesn't cover the image.
19.) Make sure DSA software is running.
If it can show fluoro or RAD image, then DSA software is being run.
Note: Make sure that WW/WL is the default value 4096/2048 during the AEC calibration process.
20.) Set Rad exposure parameters to 65kV, 400mA, AEC. Density = 0.
21.) Take digital spot exposure, turning AEC potentiometer R1 on generator AEC board until
exposure mAs is between:
For 12inch II configuration 3.6~5.0mAs.
For 9 inch II configuration 5.5-7.5mAs
Note: Turning R1 Clockwise (CW) will decrease exposure time.
22.) Click button "measure" on Brightness Measure Software, read the brightness value displayed
on edit box "Average Brightness".
23.) Keep modifying Iris until the brightness is [55, 57].
Note: Head shall be 1, and It cannot be changed.
For 12 inch II has 3 MAGs, so after finished IRIS calibration in 12inch MAG, the IRIS for 9inch
and 6inch MAG’s IRIS shall also be updated.
Below sheet is the CCD configuration for the 3 MAGs. So, after calibration the IRIS in CCD
configuration 4, choose the CCD configuration 5 and CCD configuration 7, adjust the IRIS to
same as CCD configuration 4.
15.) Connect test PC to PCU through RS232 cable. Run PCU control software on test PC.
16.) Set CCD operation mode 8 as picture below:
17.) Select Gamma config 7, confirm the Gamma configuration 7 set as “type” to “parametric”. Set
gamma = 1, then click apply.
18.) On TH800 digital box PC, Run Image brightness measure software by double click
“ImageBrightnessMeasure.exe”. A dialog will be popup. Move this dialog to left-top corner of
the monitor so that it doesn’t cover the image.
19.) Make sure DSA software is being run.
20.) Set Rad exposure parameters to 65kV, 400mA, AEC. Density = 0;
21.) Take digital spot exposure, turning AEC potentiometer R2 on generator AEC board until
exposure mAs is between:
For 12inch II configuration 3.6~5.0mAs.
For 9 inch II configuration 5.5-7.5mAs
Note: Turning R2 CW will decrease exposure time.
Turning R2 CCW will increase exposure time.
22.) Before measure image brightness, make sure that in DSA software, the Subtraction Mode is
”Normal”? If the Subtraction Mode is “Sub”, the brightness measured is not correct.
23.) Click button “Measure” on Brightness Measure Software, read the value displayed on edit box
“Average Brightness”.
24.) Keep modifying Iris until the “Average Brightness” is [55,57].
Note: Head shall be 1. It shall not be changed.
25.) DSA AEC cal done.
- Change fluoro image lag/noise, change recursive filter config 0 (table static).
- Change fluoro image lag/noise, change recursive filter config 1 (table moving).
- Recursive filter configuration 4 is for digital spot, it cannot be changed.
- Increase K will increase noise but decrease lag.
- Increase motion will decrease noise but increase lag.
2.) Sharpness and Blur
With Thales PCU control software, edge enhancement filter can be easily changed on site.
On Edge enhancement page, there is a configuration combo box. In PT800+ system real time
control logic, configuration 0 is used for fluoro mode, configuration 2 is used for digital spot and
DSA mode. System I/O board will select config 0 automatically during fluoro, and select config
2 for digital spot and DSA mode.
There are 4 filters displayed on the right side of the dialog.
- "No filter " means that the images will have no changes.
Section 4.0
Network
4.1 DICOM Configuration
Please refer to step 7 in Setup and Activation on page 229.
Section 1.0
Positioner Table
1.1 Main Function
1.2 Architecture
Refer to Positioning Table Schematics on page 415.
Trigger Signal
Table board
Logic Calculation
Movement
drive
Frequency
Motor driver 1 phase
inverter
(DC motor) motor
Collimator Communicate with (3 phase motor)
blade TDSP board Tilting movement SID movement Table top left&right
close/open and Tube Arm and Compressor
up&down movement up&down movement
Trigger signal, such as limit switch, console joystick, table side button, foot switch and so on, input
to Table Board. After logic calculation by Table Board, signal will output to X-ray Board and Motor
Board.
X-ray Board will achieve collimator blade close/open and communicate with TDSP Board.
Motor Board will drive five movements. Tilting movement and Tube arm up & down movement are
driven by Frequency Inverter (3 phase motor); Table top left & right movement and Compressor up
& down movement are driven by 1 phase motor. SID movement is driven by one DC motor.
Page 280 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
Section 2.0
Generator
Please see the details in CPI Service Manual.
Section 3.0
PDU
3.1 Function
Power supply to all subsystems include integrated console, positioner table, tube fun, and
generator.
• 220VAC for console;
• 220VAC and 110VAC for positioner table;
• 220VAC for tube fun;
• 380VAC/400VAC for generator.
3.2 Architecture
Refer to Digital System PDU Schematics on page 444.
Console
220VAC
Positioner table
Tube fun
380VAC/400VAC Isolation transformer
Console
110VAC
Positioner table
Tube fun
Generator
4.1.2 Intercom
- Console Mic to table speaker;
- Table Mic to Console speaker.
4.2 Architecture
Refer to Digital System Console Schematics on page 445.
TDSP board
WW/WL adjustment interface
Touchscreen parameter
techspot X-ray on
signal
Console interface
PCU realtime
Digital box
control
realtime interface
I.I
Generator room interface
PCU
Circular blanking
Shading correcƟon
Recursive Įůter
Last image hold
AGC
Edge enhancement
GAMMA
XRII:
TH59432 Q882 MG122 L55
(12'' II)
TH 59438 Q210 G122 L56 (-ST)
(9'' II)
Optics
Compact Camera control
lens head board
X-rays
TH 8740-020
Light
measurement
HVPS: TH 7195-3 path
Processing
and Control
Unit
EQUIPMENT
X-ray Tube
Collimator
Generator
LVDS image (1k*1k*12bits) PCU Image processing
ABC signal (Co-axis cable-analog) CCD/optics control
PC Monitor
Section 6.0
Digital Box
The Precision THUNIS-800+ digital box mainly consists of digital Imaging workstation, a console
interface board, and image frame grabber.
An analog electrical signal is obtained when the X-ray penetrates through human tissue and passes
by the image intensifier and TV camera. Such a signal is output to D.I.W where it is amplified, and
then digitized at a high speed by image frame grabber. In order to real-time display and acquire
images, the system is required to configure a high-performance and high-speed PC system,
including digital image processing unit, analog video-frequency logarithm transformation, and
image frame grabber.
The console interface board functions to guarantee the synchronization between X-ray machine’s
exposure and image acquisition so as to complete the digital spot.
The digital fluoroscopy and digital abstraction function of the system can easily be used to guide
the direction of cathetherization in the process of intervention.
The digital subtraction means to subtract normal-structure images of angiography and only display
blood vessel images. Therefore, besides the after-angiography images, the normal-structure
images before angiography are also needed.
Image output modes include image printing, image recording, and laser photography etc. Printing
is mainly used for preparing a clinic report. The printed image can only be used for reference owing
to the restriction of paper and printer. Disc recording may be used for long-term image storage and
resource sharing. The output interface of laser camera is in accordance with DICOM3 standard,
which is convenient for connection to PACS or HIS.
5DGLRVFRS\VWDWXVVLJQDO
Radioscopy mode 5DGLRVFRS\FRPPDQGVLJQDO
(Single Frameǃ1ǃ
3ǃ6.3ǃ12.5F/s)
;UD\UHDG\
(Workstation)
5DGLRVFRS\FRPPDQGRQˈ
Digital Box
VLJQDO 7KHQ;UD\RQ
;UD\21
Generator X-ray on? Generator
VLJQDO
PCI 1750
5DGLRVFRS\JDWHVHOHFWVLJQDO Card
image
collection valid
,PDJHFROOHFWLRQV\QFKURQL]DWLRQIRU3&
image
+]V\QFKURQL]DWLRQFORFN Image convertor card
collection time sequence
IF board
40ms
120ms 40ms
1s
2 frames
20ms
)OXRURVFRS\VWDWXVVLJQDO
)OXRURVFRS\&RPPDQGVLJQDO
(Workstation)
Fluoro command onˈ
Digital Box
;UD\21 Then X-ray on
Generator X-ray on? VLJQDO
Generator
PCI 1750
)OXRURVFRS\JDWHVHOHFWVLJQDO Card
Fluoroscopy image
collection valid
,PDJHFROOHFWLRQV\QFKURQL]DWLRQIRU3&
Fluoroscopy image
collection time sequence +]V\QFKURQL]DWLRQFORFN Image convertor card
IF board
40ms
Chapter 6 - Troubleshooting
Section 1.0
Positioner Table
0.1 Digital System
N N
Re-connect Cable or
Check Console Joystick or Table Re-assemble
Check Joystick or Table
N Side Button Input “BXXX” or Mechanical Part
Side Button Connection
“CXXX”. Is it charged when
of Change
Joystick or Table Side Button is
Corresponding Ones
Activated?
Y
Change Inverter
Cable N
Change Cable
Connected?
END
Page 294 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
0.1.3 Anode Not Work
Press Exposure
Restore GenWare
Factory
Configuration
No Lights on either
N Change the Lamp
Console Side or Remote
Switch
Control?
N
N
Check PDU
Change Transformer
Page 296 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
0.1.5 Collimator Movement Issue
Calibrate Collimator by
Refer to Collimator Y
Calibration, No FOV
Indication Error?
Change Collimator
Page 298 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
0.2 SID Indicator
The SID indicator on the console will display status messages during normal and abnormal
operation of table. This section contains a list of those messages and suggests actions to be taken
should any malfunctions occur.
Message Description
105-150 SID value, no film in the table cassette housing.
SID blinking 5s Not the correct SID. SID indicator blinks if fluoroscopy/digital spot is not
operated at SID of 105cm.
EEE, blinking Emergency button pressed. Please pull the emergency button out, and
reboot the system.
CCC, blinking 5s Fluoroscopy/digital spot is operated when table cassette housing has
a film inserted. Please take out the film cassette tray.
F01, a beep sounds A movement control button/joystick /foot pedal at far station side gets
stuck, or is triggered before the system power on. Make sure the
related button/joystick/foot pedal is not triggered, then power on again.
Before the system power on, no button/joystick/foot pedal should be
triggered.
F02, a beep sounds A control button at near station side gets stuck, or is pressed before the
system power on. Make sure the related button is not triggered, then
power on again.
Before the system power on, no buttons should be triggered.
F03, a beep sounds Electric motor movement time out. A related limit switch is invalid.
Please contact GE service for trouble shooting.
0.3.1 Process
1.) In “Remote” console control state, press “Full auto mode”, “Left MAG button” and “Right MAG
button” together to enter or exit the service diagnostic mode.
2.) After enter the service diagnostic mode, press down the "Left MAG button" to go forward to
display the diagnostic context, and press down the "Right MAG button" to go backward to
display the diagnostic context.
a a a
f b f b f b
g g g
e c e c e c
d d d
SEG1 SEG2 SEG3
3.) Check the 3 Remain indicators state.
Page 300 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
Table 1-1 Control signal on table side
SEG2.d Down_Side_sw “1“@Press Table side Collumn down Databus2(3)
button
SEG2.e Left_Side_sw “1“@Press Table side Top left button Databus2(4)
SEG2.f Right_Side_sw “1“@Press Table side Top right button Databus2(5)
SEG2.g Sid_Down_Side_sw “1“@Press Table side Sid Down but- Databus2(6)
ton
SEG3 SEG3.a Sid_Mid_Side_sw “1”@Press Table side Sid Mid button Databus7(0)
SEG3.b Sid_Up_Side_sw “1“@Press Table side Sid Up button Databus7(1)
SEG3.c Foot_IRC_sw “1“@Press InRoom Fluoro Pedal Databus7(2)
switch
SEG3.d Tube_Unlock_sw1 “1“@Press Tube unlock sw1 Databus7(3)
SEG3.e Tube_Unlock_sw2 “1“@Press Tube unlock sw2 Databus7(4)
SEG3.f Cassette_In “1“@Cassette Input Databus7(5)
SEG3.g rserve reserve Databus7(6)
Page 302 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
Table 1-4 Movement signal
SEG3.e SID_Motor_Enable SID_Motor_Enable=“1”and SID_Mo- Databus7(4)
SEG3.f SID_Motor_Orientation tor_Orientation=“0”when SID move up Databus7(5)
SID_Motor_Enable=“1”and SID_Mo-
tor_Orientation=“1”when SID move
down
SEG3.g TUBE_Unlock_Out “1”@Tube Lock;“0”@Tube Unlock Databus7(6)
Ca~SW: Cassette SW
Page 304 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
21LS: Tabetop_Left_sw,
41LS: COMPRESS_Up_Stop_SW
22LS: Tabetop_Right_sw
Table 5:
LED Meaning Position
100 ms On / 100 Fault Condition LED
ms Off
LED On steadily Inverter Running
500 ms On / 200 General Warning
ms Off
100 ms On / 100 Fault Condition
ms Off
Section 1.0
Generator
The Indico 100 console will display status messages on the LCD display during normal and
abnormal operation of the generator. This chapter contains tables of those messages and suggests
actions to be taken by service personnel to correct any malfunctions that may occur.
PDU Output N
Refer to PDU Check
Normally?
Generator 3 Main N
Change Fuses
Fuses Work
N Check AC Mains
3 Phase Power
Power Supply from
Works Normally
Hospital
Refer to Generator
Indication LEDs
Message Description
Generator Ready Indicates that the generator is ready to make an exposure.
Generator AEC density limit Requested density not Select another density or
programmed. program requested density
step.
Anode warning level Anode has exceeded Wait for the anode to cool.
exceeded programmed warning level.
Fluoro Focus Warning The small focus is not working, 1. Check the small filament in
and the generator is the X-ray tube.
performing fluoroscopy on the 2. Check the small-focus
large focus. filament supply board.
3. Check the filament
connections in the cathode
cable(s).
Fluoro timer warning level Fluoro interval timer > 5.0 Reset fluoro timer.
exceeded mins.
Generator duty cycle warning The X-ray generator has Re-evaluate technique
reached its duty warning limit. factors.
Allow generator to cool if
possible. If exposures are
continued, serious generator
damage may result due to
overheating.
Housing heat warning X-ray tube housing heat has Wait for the tube housing to
exceeded housing warning cool.
limit.
E001 Generator CPU Generator CPU EPROM has been Call product support for new generator
EPROM Checksum corrupted. CPU EPROM.
error
E003 Generator CPU NVRAM Generator CPU NVRAM data has Re-initialize generator CPU NVRAM
error been corrupted. using generator factory defaults.
E004 Generator CPU Real Generator CPU real time clock is not Reset time and date.
Time Clock error functioning.
E005 Main Contractor Error Unit did not detect proper charging up Measure 600V bus and determine
of 600V bus caps. reason for not charging.
Main contactor will not be closed if bus Check fuses and charging resistors on
is not charged. the power input board.
E006 Rotor Fault Current relays in main and shift Check D42 on the auxiliary board. If lit,
circuits were not energized. the inverter thermal switch is open.
This will prevent the PREP signal from
reaching the DSS board. Check the
connections of the back of the DSS
board, For proper seating.
Check DS 1 on the DSS board, if lit
there is a breakdown in the starter or
stator circuits. Disconnect stator and
retry. This will isolate where the fault
occurred.
Verify the DIP-switch settings on the
DSS board. They should be set
according to the type of tube being
used.
E007 Filament Fault Generator has detected filament 1. Check for open filament in X-ray
current <2 amps. tube.
2. Check for poor connections in the
cathode cable.
3. Check fuses on filament board(s).
E008 kV / mA Fault The generator has detected a fault in 1. If arcing of the X-ray tube is
the kV or mA output during an suspected, check condition of tube.
exposure and immediately terminated The X-ray tube may be damaged or
the exposure. This may be caused by simply require “seasoning”. Refer to
arcing in the X-ray tube, arcing of the chapter 6 for tube seasoning
HV cables, or HT tank. procedure.
2. If failure of HT tank is suspected,
contact product support.
E011 mA During Exposure Generator CPU detected mA greater Check for actual exposure mA. Do not
Too High than allowed tolerance. attempt calibration until satisfied that
generator is exposing properly.
*
E012 mA During Exposure Generator CPU detected mA less than Check for actual exposure mA. Do not
Too Low allowed tolerance. attempt calibration until satisfied that
generator is exposing properly.
*
E013 Manually Terminated Operator released exposure switch 1. Re-take exposure if necessary.
Exposure during exposure. 2. Check for faulty switch contacts or
wiring.
E014 AEC Back-up Timer- AEC exposure exceeded allowed 1. Check exposure technique settings.
Exposure Terminated back up time. 2. Check that correct AEC chamber is
energized.
E015 AEC mAs Exceeded- AEC exposure exceeded allowed 1. Check exposure technique settings.
Exposure Terminated back up mAs. 2. Check that correct AEC chamber is
energized.
E017 Uncalibrated Exposure Selected mA not calibrated for Recalibrate X-ray tube.
Parameter selected kV.
E018 Preparation Timeout Generator has been in prep state too Reduce length of time in prep state.
long.
E019 Anode Heat Limit Selected parameters will cause X-ray Reduce parameters or wait for tube to
tube to exceed its programmed anode cool.
heat limit.
E020 Thermal Switch X-ray tube # 1 too hot and its thermal Wait for X-ray tube # 1 to cool.
Interlock #1Error switch has opened.
E027 Receptor Timeout Error- The receptor is not responding Wait for receptor to be ready, then
Receptor did not retry exposure.
respond within the time-
out period
E028 Prep Input Active Prep input active during power on Check prep switch and input for short
During Initialization initialization phase. circuit.
Phase
E034 +12VDC Error +12VDC rail is out of tolerance. Check +12VDC supply from genera-
tor interface board.
E035 -12VDC Error -12VDC rail is out of tolerance. Check -12VDC supply from genera-
tor interface board.
E036 +15VDC Error +15VDC rail is out of tolerance. Check +15VDC supply from genera-
tor interface board.
E037 -15VDC Error -15VDC rail is out of tolerance. Check -15VDC supply from genera-
tor interface board.
E038 Calibration Data Corrupt Generator detects corrupt calibration Re-calibrate X-ray tube(s).
Error data.
E039 AEC Data Corrupt Generator detects corrupt AEC data. Reprogram AEC data or set factory
defaults.
E040 Fluoro Data Corrupt Generator detects corrupt fluoro data. Reprogram fluoro data or set factory
defaults.
E041 Receptor Data Corrupt Generator detects corrupt receptor Reprogram receptor data or set fac-
data. tory defaults.
E042 Tube Data Corrupt Generator detects corrupt tube data. Reprogram tube data or set factory
defaults.
E047 Fluoro Timer Limit Fluoro Timer has exceeded time limit. Reset Fluoro timer.
E048 Focus Mismatch Error Focus selected does not match Check power supply interface cables
current focus enabled by power between power supply and generator
supply. CPU board.
E049 Not Enable Requested function not programmed Reprogram to enable function or
to be enabled. change APR to not select a function.
E050 Generator Limit Data Generator detects corrupt generator Reprogram generator limit data or set
Corrupt limit data. factory defaults.
E051 AEC Feedback Error Generator has detected no, or insuffi- 1. Check that X-ray tube is pointing at
(No Feedback Signal cient, feedback signal from the AEC correct AEC device.
Detected) device. 2. Check AEC cable for damage and
proper connection.
E052 High Small Focus Fila- Generator detects small focus filament Check filament reference and
ment Current Error in current greater than limits in standby feedback signals. Substitute tube
mode. cathode with external load before
Standby
testing.
Check small focus filament board
(units with 2 filament boards), or check
filament board (units with single
filament board).
E053 High Large Focus Fila- Generator detects large focus filament Check filament reference and
ment Current Error in current greater than limits in standby feedback signals. Substitute tube
mode. cathode with external load before
Standby
testing.
Check large focus filament board
(units with 2 filament boards), or check
filament board (units with single
filament board).
E055 No Field Selected in AEC enabled but no fields are Select AEC field(s).
AEC Mode selected.
E056 Receptor Disabled All Receptors have no X-ray tube Program receptor(s) with tube
programmed. number.
E057 AEC Stop Signal in AEC stop signal (P.T. stop signal) is 1. Check that the P.T. ramp does not
Wrong State active low indicating exposure is exceed the P.T. reference during prep
finished during prep state. state.
2. Check AEC device for proper
operation.
E058 Console Back-up Timer Console has detected exposure Check routing of the console cable,
exceeded backup time and terminated route it away from noise sources. Call
exposure. product support.
This error can happen if the console
communication is corrupted during an
exposure.
E059 Housing Heat Limit X-ray tube housing has exceeded Wait for tube to cool.
Exceeded limit.
E060 High kV Error kV exceeds high kV tolerance level. 1. Check the output of the kV
reference DAC on the generator CPU
board.
2. Measure the output of the generator
with a dynalyzer or a non-invasive kVp
meter.
E061 Low kV Error kV exceeds low kV tolerance level. 1. Check the output of the kV
reference DAC on the generator CPU
board.
2. Measure the output of the generator
with a dynalyzer or a non-invasive kVp
meter.
E062 EXP_SW Signal Active The EXP_SW signal on the generator Check console overlay for damage.
in Standby State Interface and generator CPU board is Replace it if necessary.
enabled when it should be disabled.
Call product support.
E063 Factory Defaults Set SW1 switch 8 on the generator CPU Set SW1 switch 8 to the ON position.
board is set to restore the factory The generator will not exit the
defaults. initialization phase until this switch is
set.
E104 Calibration error - no mA No mA feedback detected during auto Check interface cables between lower
calibration. and upper generator cabinet.
E105 Calibration error - Minimum generator mA was exceeded Reduce filament standby current on
minimum mA not at start of calibration. primary and / or secondary filament.
calibrated This is usually caused by too high a
filament standby current on the
primary and or secondary filament.
(primary is the filament presently
being calibrated, secondary is the
other filament and applies only to
generators with two independent
filament supplies).
Table 6:
Table 7:
Table 8:
Table 9:
Table 10:
Table 11:
Table 12:
Section 2.0
PDU
Whether have N
Power Up again
Main Power Input
N
CB1 Closed? Close CB1
N
CB2 Closed? Close CB2
Fuse F1 Works N
Change Fuse F1
Normally?
Change Indication
Lamp
END
Section 3.0
Integrated Console
3.1 Intercom Trouble
turn up volume,
still no voice?
console
Mic cable and N
Re-connect or change cable
table speaker
cable Ok?
N
Key for Microphone Change Key for Microphone
OK?
Change intercom
board
turn up volume,
still no voice?
table Mic
cable and table N
Re-connect or change cable
speaker cable
Ok?
Change intercom
board
Power-Up N
N Console Fuse
Indication LED Change
Works?
Light
Y Y
PDU Output N
Circular LED
Breaker CB6 Close
Flash
Closed?
END
Y Y Y
GE EXCLUSIVE USE ONLY
Chapter 6 - Troubleshooting
N Cable CN333 Change X-ray Control
Change CN333 Cable Power-Up again
Connected? Board
N
Change TDSP Bd Display “0000” Change TDSP Board
OK
PRECISION THUNIS-800+ SERVICE MANUAL
Page 327
3.4
Page 328
GE HEALTHCARE
Emergency Fault
DIRECTION 5478064-1EN, REVISION 7
Emergency Fault
Press Emergency Button, N Buttons and It’s Cables are Y Change Table Logic I/
Emergency LED Light up? OK? O Bd
Y N Change Button or
Cable
GE EXCLUSIVE USE ONLY
Check Cable
PRECISION THUNIS-800+ SERVICE MANUAL
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
3.5 Remote Function Fault
Remote Function
Fault
N N
Reset DIP Swtich
Page 330
GE HEALTHCARE
DIRECTION 5478064-1EN, REVISION 7
Work
N
Y
Change Touch
Screen
PRECISION THUNIS-800+ SERVICE MANUAL
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
Section 4.0
Image Chain (I.C.)
Table 13:
Trouble Action
No fluoro image displayed in mon- 1.Check if monitor is powered correctly.
itor on Analog System 2. If so, check if there are characters displayed on bottom left of the moni-
tor.
3. If so, the monitor and PCU are correct, check if generator work status.
4. If there are no characters displayed on monitor, check if the cable con-
nect CCD camera and PCU connected correctly.
5. If so, connected PCU to COM port of PC, run TH8740.exe, go to display
page, check if “Analog video standard” is set to item 3: progressive. If not,
change it to item 3.
6. If PCU can’t be connected to control software, the PCU is defective,
replace a new one.
The image is not as good as usual 1. Check if exposure kV, mA, mAs are reasonable.
2. If not, check if PCU setting and generator setting is reasonable.
3. If not, set PCU and generator parameters again and redo AEC, ABC cal-
ibration according to AEC on page 267 & ABC on page 257 when neces-
sary.
Fluoro ABC fail, fluoro kV, mA 1. Check if ABC cable is connected correctly from PCU to generator.
reached highest value 2. If so, check if ABC jumper on generator interface board are set correctly.
3. Check if PCU setting is reasonable.
4. If not, redo ABC calibration according to ABC on page 257.
AEC exposure fail, exposure is cut 1. Check if AEC cable is connected correctly from PDB board to generator.
off by back up time AEC channel 1 (top one) shall be used for DR of Digital System. AEC
channel 2 shall be used for DSA of Digital System.
2. Check that J2 of PDB shall be used for Digital System.
3. If so, check if AEC jumper on generator interface board are set correctly.
4. Connect to Generator by Genware, check if the setting of receptor is rea-
sonable.
5. If all above are correct, disconnect AEC cable from generator side, take
a fixed exposure and measure the output of Thales PDB board by oscillo-
scope, there shall be DC voltage during exposure. If not, the PDB or optics
are defective.
6. Replace a new PDB and do test above again, if pass, the PDB is defec-
tive, if not, the optics are defective.
The orientation of image is not Connect PC to PCU through RS232 cable. Run PCU control software
correct (TTT). In Default Status tab of TTT, change vertical or horizontal inversion
state of PCU until the orientation of image is correct.
Display error on 19" monitor in Check the input selection switch on the back of the monitor. There are both
Digital System analog video input and PC VGA signal input on the back of the monitor.
The switch must be correctl set.
Y
OK? OK
Change Image
Convert Bd
Download GenWare Y
Factory Parameters (*.gen) OK
Change Generator
Interface Board
No AEC Function
Download GenWare Y
Factory Parameters (*.gen) OK
is OK?
AEC Cable Y
Connection is OK
OK?
Change Photodiode
Board of I.I.
No Image Acquisition
with X-ray Exposure
DICOM Print UI Y
Wait or Close Print UI
Running
Y Restart DSA, Y
END
Whether OK?
Y N
N N
Change Frame
Grabber Card and
Image Converter
Board
Page 336
GE HEALTHCARE
N
DIRECTION 5478064-1EN, REVISION 7
Y Y
Have X-ray Collimator Open?
No Image during Fluoro
Y Perform as Error
Have Error Codes
Codes
N
GE EXCLUSIVE USE ONLY
N Y
Y N
No Spot Function
Refer to
Have X-ray Exposure Y troubleshooting “No
When Joystick Spot? Image Acquisition
with X-ray Exposure”
Y Check Generator
Anode Works?
Cable Connections
Y
Y
Y
Y
Re-connect Cable
from Console I/F
Board to Generator OK
Room I/F Board
There are 3 options: No pattern, head pattern and PCU pattern.No pattern means normal usage
and no test pattern image.Head pattern means CCD head generate a test pattern and send to
PCU.PCU pattern means PCU generates a test pattern image and output it.
2.) Select Head pattern and keep TH8740 running, Check the image of PCU output (It is better
connect coaxial cable (Option 1: PAL, Option 2: SOG) to check PCU analog output directly.).
The correct image shall changes gradually from black to white from left to right as shown in
image left. If the images is not same as left image, for example, right one, that means the issue
comes from CCD or the cable connecting PCU and CCD.
Good Bad
3.) Select PCU pattern and keep TH8740 running, check the images of PCU output (co-axial
output). The correct image shall be like this:
r:2
NR:4
EE:2
COM:1 (DR=1, DSA=2)
IF this parameter are ok, we can say system IF board is ok.
2.) Exchange between fluoro and digital spot mode, check that the NDF and IRIS are running
correctly.
IF the image has no artifact, the CCD camera and its cable (5122285) are ok. We also can say may
be the bad image caused by X-ray Image Intensifier. If the same issue (the image has artifact too)
happen with visible light image, image intensifier is ok.
If the issue is still there (the image have artifact too), that means optics control board is ok.
Section 5.0
Digital Box
5.1 Error Code
In digital main screen, press Alt+ F9, enter into following error code log.
Table 15:
Type Code
Error 0x01
Warning 0x10
Information 0x11
Table 16:
Location Code
Patient management 0x01
Image acquisition 0x02
Image processing 0x03
Patient report 0x04
Recording CD 0x05
Dicom 0x06
Table 17:
Error code Description
0x1010, 0x0001 Image error, no image display
0x1001, 0x0002 Hard disk space is over limit, need to backup images to
release the hard disk space.
0x1001, 0x0003 Fail to set up a new patient case or fail to open a
patient case.
0x0102, 0x0004 Current patient case is null, can not operate.
0x0102, 0x0005 Fail to initialize controled card.
0x0102, 0x0006 Fail to initialize collecting card.
0x0102, 0x0007 Fail to use correct encrypt lock.
0x0104, 0x0008 Fail to print patient report.
0x0105, 0x0009 Fail to record.
0x0105, 0x000A Fail to load patient data.
0x0105, 0x000B Fail to burn.
0x1005, 0x000C Backup disk number can’t be 0.
0x1005, 0x000D No enough space in backup disk.
5.2 Troubleshooting
Please operate digital box in accordance with the instructions for use. Any improper operation may
result in troubles.
Whenever digital box goes in troubles, repair shall be made only by qualified and trained personnel;
otherwise, it may cause more serious system damage or personal injury.
The system may give prompts or alarms for some improper operation of digital box.
Power on system
Y
See (2)
N Enter Digital main screen
Y
N
Digital software is damaged; Operation of patient history management,
reinstall it. eg. add, store, or delete.
Y Digital software is
Connected. During fluoro, Digital damaged; reinstall it.
N monitor displays real-time fluoro
images.
Y
See (3) Connected. During fluoro, press down the
fluoro acquisition key, and acquisition is N
normal.
Y See (4)
N
Connected. Exposure
and acquisition images
are normal.
Y
See (5) N
Image printing is normal.
Y
See (6)
Normal image writing
N
Y See (7)
OK
(2)
N
Characters displayed
Y N N
Enter
Main-board
CMOS
Reconnect power
cord, reconnect Y
signal lines, or
N Video card Replace
Y replace the monitor.
damaged; replace main-board
Caused by abnormal it. End.
power-off, quit it.
N
Y
End Replace hard disk and
reinstall system software.
End.
(3)
Y
Confirm all set values
of GRABSETUP are Operate PCITEST and End
correct. press the fluoro footswitch;
PCITEST displays.
Y
N
Normal operation of
Press the fluoro footswitch, and the
EsayGrab
control box will give a sound instruction.
Y
N
Y
Data acquisition cable Incorrect CAM file storage
with bad contact or path (correct path: N
damaged D:\DSA\a201b.cam)
(4)
(5)
N
Press down the hand brake,
Press down the hand brake, and EXP and X-ray machine is exposed.
N
lamp of the interface board shines.
N
Y
Y
Exposure time: >33ms
Interface board Y
damaged; replace it
Readjust AEC
parameters
N
Acquisition is normal,
Interface board End
but images are tool
damaged; replace it.
bright or dark.
Faulty CCD
operating mode
N End
Y
(6)
Normal printing
N
Y
N
N
Operate dsasetup, and
reset the printer curve.
(7)
N
Insert a new writable
CD
Can CD writing work be
OK
ended?
Initial check: network is normal, License enable, DSA worklist parameter is right, register in RIS.
Yes
No
Yes Yes
No No
Yes
Yes
Yes
No
Yes
Yes
ǫ No ǡǫ
No
Yes
Yes
ǫ ǡǫ
No
Yes
Ǧ Ǧ
Yes
ǡǫ
No
ǡ
Yes
ǫ
No
OK
Grab setup
I.I output
Screen
DSA SW output
after ROCKEY
PCU J9
output
Run the DSA software, take an exposure, if the DSA interface doesn’t show the image on monitor.
1.) Run the GrabSetup.exe in folder :\dsa, click the init button, then click the start button.
Take an exposure, if you can see the image, it means that Image frame grabber card is ok,
possible reasons:
b.) Open the Advantech Device Manager, and the bellows pop up:
If the digital input status of 1750 card is wrong, the possible reasons are: PCI 1750 card is loosen,
the card don’t plug well, or the card is broken.
e.) Click .
f.) Take fluoro, if the interface shows normal image when take an exposure, it means that
Image frame grabber card is ok.
3.) if the easy grab interface don’t show the image when expose, please check the image of PCU
J9 output (It is better connect coaxial cable to check PCU analog output directly, Signal Mode:
Option 1: PAL, Option 2: SOG). If the monitor doesn’t show image, please check the Thales
image chain.
Section 1.0
General
To use this equipment with an optimal situation at any time, the periodic maintenance must be
required.
Section 2.0
Preventive Maintenance Action List
Operation Location Description Done
1.) General
General cleaning and painting Chapter 7 - Section 3 Preventive Maintenance - 3.1.1
Visual inspection Chapter 7 - Section 3 Preventive Maintenance - 3.1.2
2.) Positioner Table
Equipment appearance check Chapter 3 - Section 2 System Check - 2.1
Door lock and door light check Chapter 3 - Section 2 System Check - 2.2
Mains switch check Chapter 3 - Section 2 System Check - 2.2
Indicator lamp check Chapter 3 - Section 2 System Check - 2.2
Console lever Operation Chapter 3 - Section 2 System Check - 2.3
Indicator check (Digital Display) Chapter 3 - Section 2 System Check - 2.2
Insulated resistance check Chapter 7 - Section 3 Preventive Maintenance - 3.2.1
Fan Chapter 3 - Section 2 System Check - 2.2
Anode Rotation Cable check Chapter 3 - Section 2 Preventive Maintenance - 3.3.3
Detent rolling wheel check Chapter 7 - Section 3 Preventive Maintenance - 3.2.3
Collimator beam limiting adjustment Chapter 4 - Section 1 Configuration & Calibration - 1.7
Collimator field lamp illumination Chapter 7 - Section 2 Preventive Maintenance - 3.2.2
Collimator field lamp and timer Chapter 3 - Section 2 System Check - 2.3
Collimator blade movement Chapter 3 - Section 3 System Check - 2.3
Collimator adjusting screws check Chapter 7 - Section 2 Preventive Maintenance - 3.2.4
Table emergency stop check Chapter 3 - Section 2 System Check - 2.4
Tilting limit switch check Chapter 3 - Section 2 System Check - 2.3
Tilting transmission oil leak check Chapter 3 - Section 2 Preventive Maintenance - 3.1.2
Tilting motor V-belt check Chapter 7 - Section 3 Preventive Maintenance - 3.2.5
Tilting guide bearing check Chapter 7 - Section 3 Preventive Maintenance - 3.2.6
Table lateral movement check Chapter 3 - Section 2 System Check - 2.3
Table lateral movement gear check Chapter 7 - Section 3 Preventive Maintenance - 3.2.7
Tube stand longitudinal check Chapter 7 - Section 3 Preventive Maintenance - 3.2.8
Tube stand SID movement check Chapter 7 - Section 3 Preventive Maintenance - 3.2.9
SID display check Chapter 7 - Section 3 Preventive Maintenance - 3.2.10
Compression force check Chapter 7 - Section 3 Preventive Maintenance - 3.2.11
Compression cone limit check Chapter 3 - Section 2 System Check - 2.3
Compression cone roller check Chapter 7 - Section 3 Preventive Maintenance - 3.2.12
Intercom foot switch Chapter 3 - Section 2 System Check - 2.2
Microphone Chapter 3 - Section 2 System Check - 2.2
Intercom volume Chapter 3 - Section 2 System Check - 2.2
Table accessories check Chapter 3 - Section 2 Preventive Maintenance - 3.2.13
3.) Generator
Section 3.0
Preventive Maintenance
Maintenance Is To Be Performed Only By Qualified Trained Personnel Who Are Familiar With The
Potential Hazards Associated With This Equipment.
Maintenance Activities In The Table Below Are To Be Performed By Authorized Service Personnel
Only. However The Owner Or Operator Of The Equipment Must Schedule The Suggested Mainte-
nance Activity When Required By Contacting Their Local Service Agency.
Note: Maintenance schedule frequency may be determined by certain regulatory requirements of the
country or state in which the installation is located. Always check the local codes and regulations
when determining a maintenance schedule.
Always Switch Off Mains Power To The Generator And Wait A Minimum Of 5 Minutes For Capaci-
tors To Discharge Before Beginning Any Preventative Maintenance, Including Cleaning.
Observe Esd Precautions. Keep All Static - Sensitive Components And Circuit Boards In Their
Static - Shielding Packaging Until Ready To Install. Ensure That You Are Grounded At All Times
When Handling Static - Sensitive Components And Circuit Boards.
Open System
Breaker
Voltage between
Power input and
Ground
3.) Maintain the field alignment between the tube and collimator.
X-Ray Tube
Collimator
Compressor Cone
Push-pull Gauge
2.) If not, remove cover at the back of X-ray tube stand. Using 152R (5456972) to adjust
compression force to 69~98N according to the direction shown as below, at voltage 110VAC
Adjustment direction
3.2.12 Compression Cone Roller Check
1.) Set the table horizontally.
2.) From the cut-off for compression cone movement, pull the chain for the compression cone
movement by approx. 1 kg force.
3.) Measure a free play of the chain.
Specification: 3 ~ 5 mm
4.) If necessary, move the sprocket for proper free play.
3.3.2 Cleaning
Note: Refer to General Cleaning in section 3.1.1.
3.3.3 Check the Fixing and Intactness of Anode Rotation Cable and Thermal
Protection Cable
1.) Check the fixing and intactness of Anode Rotation cable and Thermal Protection cable.
2.) Check the stator cable strain relief.
Do Not Disassemble, Incinerate, Or Short-circuit The Battery(S) In This Product. Do Not Put It
In Trash That Is Disposed Of In Landfills; Dispose Of It As Required By Local Ordinances.
The Fluorescent Lamp In The Lcd Display Contains Mercury. Do Not Put It In Trash That Is
Disposed Of In Landfills; Dispose Of It As Required By Local Ordinances.
The Lcd Is Made Of Glass. If The Lcd Breaks Due To Rough Handling Or Dropping, And The
Internal Fluid Gets In Your Eyes Or On Your Hands, Immediately Wash The Affected Areas
With Water For At Least 15 Minutes. Seek Medical Attention If Any Symptoms Are Present
After Washing.
The AEC And ABS Verification Procedures Require The Production Of X-rays. Observe Correct
Operating Procedures, And Take Appropriate Precautions Against X-radiation.
3.4.1 AEC
The following procedure may be used to verify that the AEC circuits are functioning on generators
equipped with AEC (Automatic Exposure Control).
1.) Switch the console and generator ON, and select an appropriate radiographic image receptor.
2.) Align the X-ray tube and the selected image receptor such that the central ray is directly over
the center field of the AEC pickup device. Set the focal spot to film plane distance to 40 in. (1
m).
3.) Select AEC mode of operation. Select center field, large focus.
MINIMUM EXPOSURE TIME:
4.) With no object in the radiation field, adjust the collimator or beam limiting device to project a
10 in. X 10 in. (24 cm X 24 cm) field at the image receptor.
5.) Select 80 kV, 100 mA, and a backup mAs of 50 if it is operator selectable. If this is not
operator selectable, the default AEC backup settings must be used. Refer to "ms / mAs up /
down buttons and display" in section 4 to determine the AEC backup mode that has been
programmed.
6.) Make an exposure and verify that the POST mAs reading is < 2 mAs.
MAXIMUM EXPOSURE TIME:
7.) Close the collimator or beam limiting device completely. Place a folded lead apron over the
image receptor.
8.) Select 60 kV, 100 mA, and a backup mAs of 50 if it is operator selectable. If this is not
operator selectable, the default backup settings must be used.
9.) Make an exposure and verify that the error message AEC Feedback Error (No Feedback
Signal Detected), AEC Back-up Timer - Exposure Terminated, or AEC mAs Exceeded -
Exposure Terminated is displayed on the console after the exposure has terminated. This
confirms that the exposure has continued until it was terminated by the AEC backup timer.
3.4.2 ABC
The following procedure may be used to verify that the ABS circuits are functioning on generators
equipped with ABS (automatic brightness stabilization).
1.) Power up the system and choose ABC Fluoro on touch screen.
2.) Place 15cm water on positioner table. Make sure it is covered by collimator FOV.
3.) On PT800+ workstation, Run Image brightness measure software by double click
"ImageBrightnessMeasure.exe". A dialog will be popup. Move this dialog to left-top corner of
the monitor so that it doesn't cover the image.
4.) Run DSA software on workstion.
5.) Click keyboard "Alt"+"Tab" to switch DAS as current program. Take fluoro, and stop after
image is stable.
6.) Click button "Measure" on Brightness Measure Software, read the value displayed on edit box
"Average Brightness".
7.) Record the average brightness as “A”.
8.) Change the water to 10cm, do Fluoro and measure the brightness again, the brightness in
10cm conditions shall be between “A-3” to “A+3”.
1.) Place Spatial resolution card on II entrance, 45 degree. And take fluoro, Manual adjust the KV
and mA to most ideal data, verify for 12 inch II the resolution >=1.4lp/mm and for 9inch II the
resolution >=1.6lp/mm.
2.) Place Spatial resolution card on II entrance, 45 degree. Manual adjust the KV and mA to most
ideal data. Take single digital spot, verify for 12 inch II the resolution >=1.4lp/mm, for 9 inch II,
the resolution >=1.6lp/mm.
3.) Place Spatial resolution card on II entrance, 45 degree. Set series spot rate to be 1frame/s, 3
f/s, 6.3 f/s and 12.5 f/s separately, Manual adjust the KV and mA to most ideal data. take digital
spots, verify that resolution of all images, for 12inch II, the resolution shall >=1.4lp/mm, for 9
inch II, the resolution shall >=1.6lp/mm.
4.) If for 12 inch II, the resolution is not >=1.4lp/mm or for 9inch II, the resolution is not>=1.6lp/mm,
Image chain shall be checked. The optics focus and II focus shall be re-calibrated. See Image
chain service manual for more detail.
Maintenance checks /Calibration checks are done in accordance to local laws and regulations.
The person who is doing the checks should be confirmed with dosimetric measurements and
should be certified in accordance to locals regulations.
It’s recommended that the DAP system should be checked every 2 years if there is nothing
dictated by local regulations.
For how to maintain the DAP meter, please refer to the Preventive maintenance and checks
section in DAP meter’s Operating Instructions transported with system.
Section 1.0
Positioner Table
Page 376 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
Item #26
Item #45
Item #13 Item #45, 26
Page 378 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
Item#51
Item#47
Item#42 Item#48
Item#50
Page 380 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
6.) Dismount the four screws which secure the motor assembly.
8.) Remove the two gear parts from the motor assembly.
9.) Remount the Column movement motor and gear box assembly with a new one.
Section 2.0
Generator
Item # 4
Item # 26
Item # 5 Item # 7
Item # 6
Item # 12
Item # 25 Item # 24
Item # 16 Item # 28
Item # 3
Item # 32
Item # 15
Item # 10
Item # 30
Item # 13
Item # 14
Item # 13
Item # 9 Item # 17
Item # 27
Item # 31
Item # 18
Item # 23
Item # 8
Item # 33
Item # 1
Item # 35
Item # 11 Item # 2
Item # 21
Item # 21
Item # 29
Item # 22
Item # 21
Item # 19
Section 3.0
PDU
Item Part No. Name Configuration or Calibration
1 5437948 Insulation~board~assembly (PTC, used to N/A
decrease inrush current)
2 5437956 LED 110VAC N/A
3 5440279 Fuse N/A
4 5444309 Transformer for Precision THUNIS-800~ PDU See PDU Configuration
5 5449197 Relay 110VAc coil N/A
6 5449198 Relay 24VDC coil N/A
7 5458529 Relay up delay 110VAC coil For the delay time adjustment, a screwdriver is
required to adjust the center of K2/K8 relay.
K2 should be set to 1s; K8 should be set to 0.5s.
8 5461555 Contactor 30A 110VAC coil N/A
Item#2
Item#7 Item#7
Item#6
Item#5
Item#3
Item#8 Item#8
Item#4
Item#1
Item#14 Item#28
Item#15 Item#17
Item#16 Item#30
Item#27
Item#19
Item#25
Item#23 Item#18
Item#29 Item#25
Item#31 Item#29
Item#13
Section 5.0
Image Chain
Item Part No. Name Configuration or Calibration
1 5455353 12inch Image intensifier tube See ABC & See AEC
See Alignment
2 5441091 Thales Active Distortion Correction System N/A
(ADCS)
3 5439749 9inch image intensifier tube TH 59438 Q210 See ABC & See AEC
FRU See Alignment
4 5122278 CCD Camera See Alignment
5 5122279 Optics assembly for storm digital N/A
6 5122280 Thales AEC control board See AEC
7 5122281 Thales Optics control board N/A
8 5122284 Thales PCU See PCU Parameters Backup / Restore
See ABC & See AEC
9 5122282 Thales HVPS N/A
Item#9 Item#5
Item#2
Item#4
5.) Unplug the board from the CCD camera. Pay attention to the direction.
2.) Demount the CCD camera & Optics Assembly from I.I. tube.
7.) Demount the two stop plates which secure the collimator with flange.
10.) Remount the new collimator, See Collimator for detailed collimator installation steps.
The connection of tube & collimator need to use four M6×18 screws (Metric Fastener) and
need to use four 2206-M6N-05 anti-loose washers (PT800+ system provided). Make the
connection reliable.
Do not use the four screws (Inch Fastener) packed with new collimator to connect tube with
collimator.
13.) Remove the screws which lock the tube with tube handle.
16.) Remount the new tube, See A196 X-Ray Tube for how to install the tube.
Section 7.0
Miscable
Item Part No. Name
1 5462260 MIS IF board Generator IF board Interface Cable
2 5450388 MIS PCU Generator Interface Cable
3 5437146 MIS II Power and Control Cable
4 5442714 MIS CPI Input Power Cable1 U
5 5438694 MIS CPI Input Power Cable3 W
6 5456162 MIS CPI Input Power Cable2 V
7 5440236 MIS PDU Power ON Cable 2 core
8 5440237 MIS PDU CPI Ground Cable 4~
9 5451169 MIS System Console Ground Cable
10 5451170 MIS IF board Generator Digital Interface Cable
11 5449152 MIS System Console Power Cable
12 5436625 MIS collimator light SW cable
13 5445938 MIS Gen. Tube Anode cable
14 5451994 MIS Gen. Tube ground cable
15 5451171 MIS AEC Feedback Coaxial Cable
16 5450222 MIS Tube Fan Cable
17 5436460 MIS TABLE POWER CABLE
18 5439491 MIS PDU-Table Ground Cable
19 5460585 MIS intercom communication Cable
20 5457707 Table tube tilt Button and Cable
21 5448207 II Power Cable to Bulkhead J432
22 5448190 Table column SID Motor Driver Power Cable
23 5460616 Table Tube tilt Stop cable
24 5457544 Table Tube tilt Button and pitching limit SW Cable
25 5440079 Table SID Driver Control Cable
26 5459961 Table SID motor base ground cable
27 5437143 Table tube 0 degree SW cable
28 5451809 Table SID potentiometer Cable
29 5456779-1 Collimator control cable 1
30 5452651 Collimator Power cable
31 5443491 Collimator ground cable
32 5436968 Table Limit SW cable
33 5437749 Table TOP LR motor cable
34 5441077 Table TOP LR motor base ground cable
35 5443329 TDSP CN332 MIS Cable
36 5448191 Table cassette absence cable 2
37 5448194 Table column UD Motor Power Cable
Item#42
Section 1.0
Scope
This section describes the MIS (Master Interconnection System) map.
Section 2.0
Symbols/Conventions
The equipment outlines on the map identify where connections are made. These outlines are usually cabinets or major assemblies. Internal divisions
show modules/circuit boards. These components are identified using the component location codes defined for each product. (If you are unfamiliar
with these codes refer to the schematics direction for any major product. It is worth your effort to learn these codes.)
MIS runs are identified by lines between connection points, with the MIS number in an oval at each end of the line.
Section 3.0
Digital System MIS Map
A hardcopy version of system MIS map, 5444843SCH, is shipped with system. This schematic shows all of MIS cables and their termination points.
A version appropriate for viewing electronically is provided here.
1 2 3 4 5 6 7 8
C Patient C
Remote R&F Table
Table Electronics
Grid 10:1
Film Cassette(option)
D D
ROOM Interface
Power
Image Intensifier
H
Generator Interface V
P '$3',63/$<(5
S Optics 2SWLRQDO
AEC Board CCD
E AEC Feedback (Photodiode) Camera Imager
E
Digital Interface PCU
ABS Feedback (Proportional DC) Digital
VACUTEC
Subsystem
CPI
F Touchscreen RS232 F
XRay Console Console
Thales Interface
To Gen Room IF &
Boards
Hundicmed Digital IF DSA Injector connection cable
Varian
Block Diagram
1 Wu Shengyong 02/26/2013 - Initial release
CHECK
FIRST MADE FOR: Precision THUNIS-800+ 3
APPR
2 Wu Shengyong 28-JUN-2013 2152888 Table 1: Rev 1 to 2 modify list
OTHER
5444843SCH SHT/CONT ON
3 Wu Shengyong 09-DEC-2013 2163095 Table 2: Rev 3 to 4 modify list 1/2
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Remote Console
65/50KW R&F Generator
A P/N 5123374 Digital Box A
Generator I/F Boards (Workstation)
Image Monitor
DVI Video
In-Room Monitor
X-Ray ON CDR-W
Warning
Analog Video_4 MIS 5456163 5438408
TB4 @ ROOM INTERFACE BOARD 1750 I/O Card
Light
DICOM
Frame Grabber
Keyboard
B Door
Image convert board PC Mouse
L B
Interlock TB4 @ ROOM INTERFACE BOARD L
Switch PC
PWR L
COM1 COM2
'LJLWDOLPDJH N
VXEV\VWHP N MIS 5438695
MIS 5451170 N
J2 @DIGITAL INTERFACE
BOARD E
E
J8 @ DIGITAL INTERFACE MIS 5450388 E
J4 (ABC Feedback Signal)
BOARD L
C R&F Table C
P/N 5443244 J6
II Image Chain
MIS 5122285
{ AEC Channel#2 for DSA Camera Head LVDS J1 (To Camera Head)
Pin7-, Pin12+ Ferrite:
AEC Channel#1 for spot MIS 5451171 AEC Feedback Signal
J432 5479710
J1, J2@ Xray APR Console
24VDC @ROOM
AEC INTERFACE
II PWR Imager PCU J4 (Touchscreen LCD)
MIS 5440236 INTERFACE BOARD
D J4 @GENERATOR
MIS 5123315 Gen
D
INTERFACE PWB
Ferrite:
5479713
GND MIS 5124835 COM1
Stud
Console Table
Power Distribution
Console Cabinet
P/N
System PDU
P/N 5439221
H Connected With Bulkhead
REV MADE BY DATE
REVISIONS
ECR NO. DESCRIPTION
MADE
APPROVALS YY/MM/DD TITLE
Precision THUNIS-800+ System Interconnects
REV H
Option
1 Wu Shengyong 02/26/2013 - Initial release
CHECK
FIRST MADE FOR: Precision THUNIS-800+ 3
2 APPR
Wu Shengyong 28-JUN-2013 2152888 Table 1: Rev 1 to 2 modify list
OTHER
GE Healthcare China 5444843SCH SHT/CONT ON
3 Wu Shengyong 09-DEC-2013 2163095 Table 2: Rev 3 to- 4 modify list 2/2
1 2 3 4 5 6 7 8
Chapter 10 - Schematics
Section 1.0
Positioner Table
1.1 Positioning Table Schematics
1 2 3 4 5 6 7 8
Tilt stop sw:
5453710&5436678 Tilt
Tilt Stop LS Assy 5453492 J7 Table Board Motor Board Frequency Inverter 1100W 5448361 R/F/I
A3 1LS-COM G24 5473932 J4 5451810 IO 5476829 U A4 3Phase Motor
A 1 5444620 1 GND 1 V 220Vac,4P,1100W A
1LS 1LS-NC 90_stop_sw A1 B1 Tilt_inverter_DO A2 FC1
(Vertical) G24
2 A1 B2 2 2 W M1
2LS-COM 3 Tilt_inverter_DI0
2LS 2LS-NC 0_stop_sw PWA: 5458763 3 3
4 4 Tilt_inverter_DI1 4
(Level&:) 3LS-COM G24 Tilt_inverter_DI2 PE 5462125
5 5 5
3LS 3LS-NC -30_stop_sw 6 Tilt_inverter_+24V
6 6 PE
(Incline)
Tilt_inverter_G24 A2-E5
6p 7 7 L A2-E4
PE N
Tilt Over LS Assy 10 10
A4
5447377 J12 10p
Tilt over sw: 4LS-COM G24 1
5462125 collumn
5448409 4LS -30_over_sw
4LS-NC
G24
2 Frequency Inverter W 5448194 U/D
B (Incline)
5LS
5LS-COM
5LS-NC 90_over_sw
3 J5
GND
5440915 IO 5476828 U A3 3Phase Motor B
4 1 1 V 220Vac,4P,0W
(Vertical) G24 Tube_inverter_DO A2 FC2
6LS
6LS-COM
-15_stop_sw
5 2 2 W M2
(-1)
6LS-NC 6 J15 J6 3 Tube_inverter_DI0 3
Board Interface Cable2 Tube_inverter_DI1
7 4 4 PE
8 5462259 5 Tube_inverter_DI2 5
34p 34p
6 Tube_inverter_+24V 6
5448364
8p PE
7 Tube_inverter_G24
PE 7 L A2-E3
CPLD 10 10 N A2-E11
J2 10p
5447378
X2 4 EPM2210 24VGnd
5462125
1 1 1
C 2
1 5437143
J20 J4 2 J8 2 24Vdc 2SWLRQ'$3PHWHU C
2 48LS-COM 3 / 1
X1 3 3 4 0Vac
LQFOXGH 48LS-NO 2 JTAG
J2 3p 3 110Vac
(0EXWWRQ J1
Key board /6 1 10p 2
5450689 220Vac
7XEHWLOW 1 5<
Angle LCM A5 B1
5440086
5459815 J3,J7,J9 4p 5<$ A2
J3 5444956
A5 B2
A2 RY1 5462125 A2 Fuse TM1
7DEOH J1 CN81 1
POWER_RELAY_24V F1 10A 5462125
D J1 J3 6HH7DEOH 6HH7DEOH J351 GND 5< 9 ) ) 9DF 70
2 70 220Vac
5458480 5450223 26p 0,6
3 9 F2 10A 70 220Vac
3p 5< ) ) 9DF 2 2 3'8- D
70
5<
J1 9DF
CN81 Switch Power W F3 2A 70
+24Vdc 5< ) ) 3 3
1 123 5<
&RYHU 24G 5440911(ZWQ130-5224/A) 70
2 456 F4 2A 1 70 4 4 0V-N
$&RYHU EDVH RKP
A1 P1
CN1 5446565 5< ) ) 9DF
70
4p 5< 1 70 0V-N
5453650 / 5 5
5G 1 5<$
F5 4A
) 70
3 5678 3 N A1 A2 9 ) 9DF 70 6 6
+5Vdc PE
GND
4 1234 5 70
CN51 5436979 Fuse holder X 5: 70
7 7 110 Vac
E
5453489
table to 4p 5453489 1 2 2 3 5438742
5p 70
cover base 8 8
CN1 4p
E
+5Vdc
5G
5462125 9 9
) 7UDQV
L
70 220Vac
N
) 70
HS15 3R3 J J1 1
J8 2 )
5451808 TM11 5436968 A1 R1 Slave A2-E12 )
+1vdc
-1vdc
21LS-COM G24 Intercom 5440286
1G
1G
21LS 1 1 5453489 )
(Left) 21LS-NO Tabetop_Left_sw 48V Switch Power DC 48V Power Cable to DC copper socket x 3:
22LS-COM
2 2 5168929
J7,J8 SID Motor Driver-5448190
22LS 22LS-NO
3
Tabetop_Right_sw 3 J14 ,J9
5453489 5462129(HWS300-48) 5462125
(Right) 4 4 A2 P1 7DEOH*URXQG&DEOH
G24 GHEXJ
F 5445779 11LS-COM 5
Collumn_Up_sw 5 A2-E WR3'8
11LS 6 6 J1 4p
11LS-NC G24
(Up)
5453488
12LS-COM
7
8
Collumn_Down_sw 7
8 1 2 3 4
F
12LS G24 N A2-E13
(Down) 12LS-NC 9
Collumn_UD_Stop_sw 9 J11 J11 Xray Board L 85YKVEJ2QYGT
10 10 Board Interface Cable1
13LS
13LS-COM
13LS-NC
5440286 10p
5456160
5440559
9GF #2
Area Designations
(U/D) 24Vdc
50p 50p A1 B3 9*QG
24V_Gnd
5438532 A1 - Table Base PCB board assembly
left/right/UD sw:
5448409 A2 - Table Power in Assmbly
up/down sw: J5,J6 A2-E2 A3 - Table Main Frame Assembly
G 5461564
J9,J16 A4 - Table Base Motor Assembly
TM12TM12-1 220
2 3 4 5 6 7 8
L
Page 416 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1 2 3 4 5 6 7 8
5462294
CN12 J82
Operation indication
1 1
Col_RES-
1 Xray Board
2VR 1VR 1PR 2PR Col_RES+ 2 5440559
2 2
Col_FED_UD 3
3 3 A1 B3 A2
E 4 4
Col_FED_LR
Col_LR
4 E
5 5
Col_UD
5 TM1
6 6 6
4LS Mot_LR+
7 7 7
2 3LS Mot_LR-
8 8 8
M Mot_UD+ 2 2
1LS 9 9 9
Mot_UD-
1 2LS 10 10
GND
10 3 3 Area Designations
M 11 11 11
12 12 12 4 4
J1,J11 A1 - Table Base PCB board assembly
5456779-2 5 5
16 16 12p J332 A2 - Table Power in Assmbly
F 70 6 6 A3 - Table Main Frame Assembly F
5452651 Transformer 5462125 7 7 A4 - Table Base Motor Assembly
AC12V L / 12Vac Fuse
X23
110VAC 70 A5 - Table Front Assembly
/ 0VAC 8 8
100W N A6 - Table Tower Assembly
0Vac 0Vac 9 9 A7 - Table Tube and Collimator
5440286
A8 - Table Case and Image Chain
L3
5454576 A2-E1
5436625 Collimator SW MIS cable
Collimator L4
to Console -5460785
G 5167951-ਹ⭠<6-51 G
A7 To Tube
5443491
J7
#$ 0,& 27+(5
5437161
29#
0,& A2-E
5(9,6,216 $33529$/6 <<00'' 7,7/(
5(9
H J9 63.
5444084
5(9 0$'(%< '$7( (&512 '(6&5,37,21
0$'(
&+(&.
3637SRVLWLRQLQJWDEOH6&+
H
63. :X6KHQJ\RQJ - Initial release ),5670$'()25 3UHFLVLRQ7+81,6
CN21 :X6KHQJ\RQJ -81 7DEOH5HYWRPRGLI\OLVW
$335
5436985 MIS 5460585
72FRQVROH,QWHUFRP-
5443244SCH 6+7&21721
J8 See Table 3 See Table 3
:X6KHQJ\RQJ -8/ )$XSGDWHWR)$ 27+(5
*(0(',&$/6<67(06
:X6KHQJ\RQJ '(&
7DEOH5HYWRPRGLI\OLVW
1 2 4 5 6 7 8
7$%/( 7$%/(
7$%/(
Key board CABLE Table SID Driver Control Cable
$ $
keyboard Table board PS800 Refresh Angle LCM cable
CN81 SIGNAL NAME Motor board DC motor SIGNAL NAME
J1 J351 Key Angle J7 driver J5
SIGNAL NAME
VCC_24V board J3 LCM J1 Enable Input[IN1]
VCC_24V 1 1 VCC_24V Signal Ground
VCC_24V 2 2 VCC_24V Programmable Input[IN2]
% VCC_24V 3 3 ANGLE_LCD_BUSY Signal Ground
%
G24 4 4 ANGLE_LCD_TXD Programmable Input[IN3]
G24 5 5 ANGLE_LCD_RXD Signal Ground
G24 6 ANGLE_LCD_RXD Programmable Input[IN4]
G24 7 7 G24 Signal Ground
RESERVE 8 8 G24 Programmable Input[IN6]
& &
LAMP_SIDE_SW Signal Ground
RISE_SIDE_SW Programmable Input[IN7]
FALL_SIDE_SW Signal Ground
UP_SIDE_SW Programmable Output[OUT1]
DOWN_SIDE_SW 5V_ACJ
' '
RIGHT_SIDE_SW Programmable Output[OUT2]
LEFT_SIDE_SW 5V_ACJ
SID_UP_SW
SID_MID_SW
7$%/(
SID_DOWN_SW
( TABLE_EM_SW intercom cable (
Master Slave
EMERGENCY_LED CN21 SIGNAL NAME
Intercom J8 Intercom J8
CONSOLE_EM_SW
12V
ANGLE_LCD_BUSY GND
ANGLE_LCD_RXD RS485_A_1
) )
ANGLE_LCD_TXD RS485_B_1
RS485_A_2
RS485_B_2
5V_ISO
GND_ISO
* *
5(9,6,216 $33529$/6 <<00''
0$'(
5(9 0$'(%< '$7( (&512 '(6&5,37,21
&+(&.
:X6KHQJ\RQJ -$1 7DEOH5HYWRPRGLI\OLVW
$35 $335
:X6KHQJ\RQJ
'HOHWHIRU,QFK
27+(5
Page 418 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1.2 Key Board (5450689)
1 2 3 4
B
the ECR/ECO Process.
t.
1 2 3 4 5 6 7 8
J1
J3
VCC_24V 1 1 2 2 VCC_24V
3 4 VCC_24V J2
VCC_24V 3 4
G24 5 6 G24 VCC_24V 1 1
A G24 7
5
7
6
8 8 G24 CONSOLE_EM_SW 1
VCC_24V 2 2 A
RESERVE 9 10 LAMP_SIDE_SW 1 ANGLE_LCD_BUSY 3 3
9 10 TABLE_EM_SW 2 2
RISE_SIDE_SW 11 11 12 12 FALL_SIDE_SW ANGLE_LCD_TXD 4 4
VCC_24V 3 3 ANGLE_LCD_RXD 5
UP_SIDE_SW 13 13 14 14 DOWN_SIDE_SW 4 5
RIGHT_SIDE_SW 15 16 LEFT_SIDE_SW EMERGENCY_LED 4 ANGLE_LCD_RXD 6 6
15 16
SID_UP_SW 17 17 18 18 SID_MID_SW G24 7 7
SID_DOWN_SW 19 19 20 20 TABLE_EM_SW G24 8 8
EMERGENCY_LED 21 22 CONSOLE_EM_SW PIN
21 22 RIGHT_ANGLE
23 23 24 24 ANGLE_LCD_BUSY
ANGLE_LCD_RXD 25 26 ANGLE_LCD_TXD WIRE_TO_BOARD PIN
25 26
EMERGENCY SWITCH RIGHT_ANGLE
ANGLE LCD POWER SUPPLY WIRE_TO_BOARD
PIN
RIGHT_ANGLE
RIBBON_CABLE_LOW_PROFILE
7 7 A3 7 A3 7
SW
A3
SW
A3 SW SW SID_DOWN_SW
G24 RISE_SIDE_SW G24 1 UP_SIDE_SW G24 1 2 RIGHT_SIDE_SW G24 1 B0 2
1 B0 A0 2 B0 A0 2 B0 A0 A0
3 4 3 4 3 - + 4 3 - + 4
- + - +
5 6 5 6 5 - + 6 5 - + 6
- + - +
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
(TABLE TURN RIGHT) (PILLAR MOVE LEFT) (TOP MOVE FRONT) (SID_UP)
A3 7 A3 7 A3 7 A3 7
SW SW DOWN_SIDE_SW SW LEFT_SIDE_SW SW
G24 1 2 FALL_SIDE_SW G24 1 B0 A0 2 G24 1 B0 A0 2 G24 1 2 SID_MID_SW
B0 A0 B0 A0
See the GEHC Myworkshop System to determine the status of this document.
3 - + 4 3 - + 4 3 - + 4 3 - + 4
5 - + 6 5 - + 6 5 - + 6 5 - + 6
C C
CR1 I19
CR2
SMS24C SMS24C S9
I17
G24 7 S1
DOWN_SIDE_SW 1 1 SID_UP_SW A3
1 1 SW
1 B0 A0 2 RESERVE A3 7
R1 G24 SW
3 4 VCC_24V 1 B0 A0 2 SID_UP_SW
RESERVE 3 3 LEFT_SIDE_SW 3 LAMP_SIDE_SW - +
3 3 4
5 - + 6 2.2K - +
FALL_SIDE_SW 0.5W 5 6
4 4 2 2 P_GND RIGHT_SIDE_SW 4 2 P_GND 5%
- +
4 2
RESERVE R2
RISE_SIDE_SW 5 SID_DOWN
5 SID_DOWN_SW 5 5 (TRANSITION LAMP)
2.2K
0.5W (SID_DOWN)
UP_SIDE_SW 6 SID_MID_SW 5%
6 6 6
26.7V 26.7V
REV 2 01July04
P_GND
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Mar 29 14:35:11 2013 key_board 2 of 2 5450689SCH 2 2 of 12
1
Approved Document - 5450689SCH_r2.pdf Page 3 of 3
2 3 4 5 6 7 8
Page 420 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1.3 Table Board (5458763)
1 2 3 4 5 6 7 8
GENERAL NOTES:
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
See the GEHC Myworkshop System to determine the status of this document.
C C
D D
REV 2 01July04
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Sun Jun 09 16:51:38 2013 table_board 1 of 12 5458763SCH 2 1 of 12
1 2
Approved Document - 5458763SCH_r2.pdf Page 2 of 13
3 4 5 6 7 8
1 2 3 4 5 6 7 8
0.125W
A1 1
R12
SW_CODE<7> VCCINT<7..0>
20K
1%
3 K VCCIO1<3..0>
A2 2 U13 U13
VCCIO2<3..0>
74VHC_AHC14 74VHC_AHC14
R16 VCCIO3<3..0>
70V
VCCIO4<3..0>
VR1
A ADP3339-3.3
2K GCLK_1M H5 IO_H5_GCLK0
SW_CODE<7> 1 A B 2 3 A B 4 GCLRN A
0.125W GCLK_RESERVE J5 IO_J5_GCLK1
1% J12 IO_J12_GCLK2
100U
35V
20%
VCC=3V3;GND=GND VCC=3V3;GND=GND
C4
3 VIN VOUT
4 2 H12 IO_H12_GCLK3
M8 IO_M8_DEV_OE
GND 1 GCLRN M9 IO_M9_DEV_NCLR IO_B16 B16 TUBE_PITCHING_DETECTOR_CPLD U14
IO_C13 C13 TUBE_UNLOCK_SW1_CPLD EPM2210F256C5N
35V
10%
C5
1U
TDI L6 TDI IO_A15 A15 TUBE_UNLOCK_SW2_CPLD
35V
10%
C3
1U
3.3V TMS N4 TMS IO_C12 C12 SID_MIDDLE_STOP_CPLD
TCK P3 TCK IO_B14 B14 SID_UP_STOP_CPLD TILT_CTRL_OUT_0 P14 IO_P14 IO_R1 R1 SW_CODE<0>
TDO M5 TDO IO_D12 D12 SID_UP_OVER_CPLD TILT_CTRL_OUT_1 P15 IO_P15 IO_P4 P4 SW_CODE<1>
IO_B13 B13 SID_DOWN_STOP_CPLD TILT_CTRL_OUT_2 N13 IO_N13 IO_T2 T2 SW_CODE<2>
VERTICAL_STOP_CPLD D3 IO_D3 IO_C11 C11 TUBE_LEVEL_DETECTOR_CPLD TUBE_MOVE_CTRL_OUT_0 N14 IO_N14 IO_P5 P5 SW_CODE<3>
VERTICAL_OVER_CPLD C2 IO_C2 IO_A13 A13 DI_TO_CPLD<0> TUBE_MOVE_CTRL_OUT_1 M14 IO_M14 IO_R3 R3 SW_CODE<4>
INCLINE_STOP_CPLD C3 IO_C3 IO_D11 D11 DI_TO_CPLD<1> TUBE_MOVE_CTRL_OUT_2 N15 IO_N15 IO_N5 N5 SW_CODE<5>
INCLINE_OVER_CPLD E3 IO_E3 IO_B12 B12 DI_TO_CPLD<2> M13 IO_M13 IO_R4 R4 SW_CODE<6>
LEVEL_CW_STOP_CPLD D2 E11 DI_TO_CPLD<3> TOP_CTRL_OUT_0 N16 P6 SW_CODE<7>
3V3 CPLD CLOCK 1M LEVEL_CCW_STOP_CPLD E4
IO_D2
IO_E4
IO_E11
IO_A12 A12 DI_TO_CPLD<4> TOP_CTRL_OUT_1 L14
IO_N16
IO_L14
IO_P6
IO_T4 T4 LED_OUT_1<0>
Y1 LEFT_LIMIT_CPLD D1 IO_D1 IO_C10 C10 DI_TO_CPLD<5> COMPRESS_CTRL_OUT_0 M15 IO_M15 IO_N6 N6 LED_OUT_1<1>
RIGHT_LIMIT_CPLD E5 IO_E5 IO_B11 B11 DI_TO_CPLD<6> COMPRESS_CTRL_OUT_1 L13 IO_L13 IO_R5 R5 LED_OUT_1<2>
UP_LIMIT_CPLD E2 IO_E2 IO_D10 D10 DI_TO_CPLD<7> LAMP_SIDE_CPLD M16 IO_M16 IO_M6 M6 LED_OUT_1<3>
DOWN_LIMIT_CPLD F3 IO_F3 IO_A11 A11 TILT_IVT_DO_CPLD MOTOR_RESERVE_MOTOR L12 IO_L12 IO_T5 T5 LED_OUT_1<4>
4 VCC VOUT 3 GCLK_1M UD_RANGE_STOP_CPLD E1 IO_E1 IO_E10 E10 TUBE_IVT_DO_CPLD COMPRESS_LED_CONSOLE L15 IO_L15 IO_P7 P7 LED_OUT_1<5>
R11 F4 IO_F4 IO_B10 B10 SID_IO_OUT1_CPLD SID_MOTOR_OUT_3 L11 IO_L11 IO_R6 R6 LED_OUT_1<6>
1 2 CASSTTE_IN_CPLD F2 IO_F2 IO_C9 C9 TUBE_PITCHING_OP_0_CPLD SID_MOTOR_OUT_2 L16 IO_L16 IO_N7 N7 LED_OUT_1<7>
ENABLE GND MINUS_15_DEGREE_STOP_CPLD F5 A10 TUBE_PITCHING_OP_1_CPLD SID_MOTOR_OUT_1 K14 T6
IO_F5 IO_A10 IO_K14 IO_T6
B 2K B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
0.125W
0.125W
0.125W
R10
R13
R14
R15
1%
1K
1%
1K
1%
1K
1%
TDO 3 3 4 4 EMERGENCY_CPLD L5 IO_L5 IO_C4 C4 ANGLE_LCD_BUSY_CPLD DO-TO_CONSOLE<15> F13 IO_F13 IO_T13 T13
TMS 5 5 6 6 COM_UP_IRC_CPLD M2 IO_M2 IO_C5 C5 AD_SCLK_COL COL-CPLD<0> D16 IO_D16 IO_M12 M12 DA_SYNC_N
7 7 8 8 COM_DOWN_IRC_CPLD L4 IO_L4 IO_B3 B3 AD_CS_N_COL COL-CPLD<1> F14 IO_F14 IO_R13 R13 DA_SCLK
TDI 9 9 10 10 FOOT_IRC_CPLD L3 IO_L3 IO_D5 D5 AD_DIN_COL COL-CPLD<2> D15 IO_D15 IO_N12 N12 DA_DIN
XRAY_IRC_CPLD N1 IO_N1 IO_A2 A2 AD_DOUT_COL COL-CPLD<3> E12 IO_E12 IO_R14 R14 DA_LDAC_N
SID_UP_SIDE_CPLD M4 IO_M4 IO_B1 B1 SDA_E2PROM COL-CPLD<4> D14 IO_D14 IO_P12 P12 AD_CS_N
PIN SID_MID_SIDE_CPLD N2 IO_N2 IO_D4 D4 SCL_E2PROM COL-CPLD<5> E13 IO_E13 IO_T15 T15 AD_SCLK
STRAIGHT SID_DOWN_SIDE_CPLD M3 IO_M3 COL-CPLD<6> C15 IO_C15 IO_R16 R16 AD_DOUT
RIBBON_CABLE_LOW_PROFILE PDU_STATE_CPLD N3 IO_N3 GNDINT<7..0> COL-CPLD<7> C14 IO_C14 IO_P13 P13 AD_DIN
COMPRESS_UP_STOP_CPLD P2 IO_P2 GNDIO<15..0> E14 IO_E14
POWER_RELAY_TIMER_CPLD D13
CPLD CLOCK 10M SYM 1 OF 2
IO_D13
SYM 2 OF 2
3V3
RESERVE NO JOINTING
Y2 3V3
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C30
C31
C32
C33
ENABLE GND
C9
2K
0.125W
10MHZ
1%
D C140 D
REV 2 01July04
0.1U
50V
10%
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Feb 01 15:21:21 2013 table_board 2 of 12 5458763SCH 2 2 of 12
1
Approved Document - 5458763SCH_r2.pdf Page 3 of 13
2 3 4 5 6 7 8
Page 422 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1 2 3 4 5 6 7 8
3V3
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
C21
C22
C23
C24
C25
C26
C27
C28
C29
CPLD INPUT VOLTAGE CONVERT 5V TO 3.3V
A A
U17
74LVTH244
U19
U15
74LVTH244
74LVTH244 1 OE_N<1>
1 OE_N<1> TILT_FALL_CONSOLE_74 2 A1<1> Y1<1> 18 TILT_FALL_CONSOLE_CPLD
1 OE_N<1> TILT_FALLINV_CONSOLE_74 4 A2<1> Y2<1> 16 TILT_FALLINV_CONSOLE_CPLD
UP_LIMIT_74 2 A1<1> Y1<1> 18 UP_LIMIT_CPLD TUBE_UP_CONSOLE_74 6 A3<1> Y3<1> 14 TUBE_UP_CONSOLE_CPLD
VERTICAL_STOP_74 2 A1<1> Y1<1> 18 VERTICAL_STOP_CPLD
DOWN_LIMIT_74 4 A2<1> Y2<1> 16 DOWN_LIMIT_CPLD TUBE_DOWN_CONSOLE_74 8 A4<1> Y4<1> 12 TUBE_DOWN_CONSOLE_CPLD
VERTICAL_OVER_74 4 A2<1> Y2<1> 16 VERTICAL_OVER_CPLD
UD_RANGE_STOP_74 6 A3<1> Y3<1> 14 UD_RANGE_STOP_CPLD
INCLINE_STOP_74 6 A3<1> Y3<1> 14 INCLINE_STOP_CPLD
MINUS_15_DEGREE_STOP_74 8 A4<1> Y4<1> 12 MINUS_15_DEGREE_STOP_CPLD 19 OE_N<0>
INCLINE_OVER_74 8 A4<1> Y4<1> 12 INCLINE_OVER_CPLD
0.125W
R22
19 OE_N<0> TOP_LEFT_CONSOLE_74 11 A1<0> Y1<0> 9 TOP_LEFT_CONSOLE_CPLD
1K
1%
19 OE_N<0>
0.125W 1K 1%
TOP_RIGHT_CONSOLE_74 13 A2<0> Y2<0> 7 TOP_RIGHT_CONSOLE_CPLD
R20
0.125W
11 9 15 5
R18
1%
VCC=3V3;GND=GND
VCC=3V3;GND=GND
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
U22
U18 74LVTH244
U20
74LVTH244
74LVTH244
1 OE_N<1>
1 OE_N<1> 1 OE_N<1> FOOT_IRC_74 2 A1<1> Y1<1> 18 FOOT_IRC_CPLD
See the GEHC Myworkshop System to determine the status of this document.
1K 1%
19 OE_N<0> 19 OE_N<0> SID_DOWN_SIDE_74 11 A1<0> Y1<0> 9 SID_DOWN_SIDE_CPLD
1%
0.125W
11 9 13 7
R19
SID_MID_CONSOLE_74 A1<0> Y1<0> SID_MID_CONSOLE_CPLD PDU_STATE_74 A2<0> Y2<0> PDU_STATE_CPLD
TOP_RIGHT_SIDE_74 11 A1<0> Y1<0> 9 TOP_RIGHT_SIDE_CPLD
1K
1%
SID_UP_CONSOLE_74 13 A2<0> Y2<0> 7 SID_UP_CONSOLE_CPLD COMPRESS_UP_STOP_74 15 A3<0> Y3<0> 5 COMPRESS_UP_STOP_CPLD
0.125W 1K
0.125W
15 5 17 3
R21
TILT_RISE_SIDE_74 A3<0> Y3<0> TILT_RISE_SIDE_CPLD TUBE_PITCHING_DETECTOR_74 A4<0> Y4<0> TUBE_PITCHING_DETECTOR_CPLD
COM_UP_IRC_74 15 A3<0> Y3<0> 5 COM_UP_IRC_CPLD
TILT_FALL_SIDE_74 17 A4<0> Y4<0> 3 TILT_FALL_SIDE_CPLD
C COM_DOWN_IRC_74 17 A4<0> Y4<0> 3 COM_DOWN_IRC_CPLD C
VCC=3V3;GND=GND
VCC=3V3;GND=GND
VCC=3V3;GND=GND
U16
U21 U23
74LVTH244
74LVTH244 74LVTH244
1 1 OE_N<1>
OE_N<1> 1 OE_N<1>
2 18 TILT_IVT_DO_74 2 A1<1> Y1<1> 18 TILT_IVT_DO_CPLD
TUBE_UNLOCK_SW1_74 A1<1> Y1<1> TUBE_UNLOCK_SW1_CPLD DI_FROM_CONSOLE<0> 2 A1<1> Y1<1> 18 DI_TO_CPLD<0>
4 16 TUBE_IVT_DO_74 4 A2<1> Y2<1> 16 TUBE_IVT_DO_CPLD
TUBE_UNLOCK_SW2_74 A2<1> Y2<1> TUBE_UNLOCK_SW2_CPLD DI_FROM_CONSOLE<1> 4 A2<1> Y2<1> 16 DI_TO_CPLD<1>
6 14 SID_IO_OUT1_74 6 A3<1> Y3<1> 14 SID_IO_OUT1_CPLD
SID_MIDDLE_STOP_74 A3<1> Y3<1> SID_MIDDLE_STOP_CPLD DI_FROM_CONSOLE<2> 6 A3<1> Y3<1> 14 DI_TO_CPLD<2>
0.125W
19 19 OE_N<0>
OE_N<0> 19 OE_N<0>
0.125W
R17
11 9
R23
1K
1%
11 9 11 9
R25
D D
VCC=3V3;GND=GND
VCC=3V3;GND=GND VCC=3V3;GND=GND
REV 2 01July04
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Feb 01 15:21:21 2013 table_board 3 of 12 5458763SCH 2 3 of 12
1
Approved Document - 5458763SCH_r2.pdf Page 4 of 13
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
LED_DISPLAY
MODE SELECT SWITCH COLLIMATOR WINDOW CONTROL ADJUST SWITCH
3V3 DS2 3V3 DS10
HSMG-C190 LED_OUT_1<7..0> HSMG-C190 LED_OUT_2<7..0>
3V3 3V3
R26 R190
2 1 0 2 1 0
A S1 SW_CODE<7..0>
0
R34 S3 SW_CODE_COL<7..0>
0
R43 475
GREEN
475
GREEN
A
219-04MST 219-04MST 0.125W 0.125W
1% DS3 1% DS11
2K 2K
HSMG-C190 HSMG-C190
1 I1 O1 8 0 0.125W 1 I1 O1 8 0 0.125W
1% 1% R27 R191
2 1 1 2 1 1
2 I2 O2 7 1 R35 2 I2 O2 7 1 R44
1 1 475 475
3 I3 O3 6 2 3 I3 O3 6 2 GREEN GREEN
0.125W 0.125W
2K 2K
1% DS4 1% DS12
4 I4 O4 5 3 0.125W 4 I4 O4 5 3 0.125W
HSMG-C190 HSMG-C190
1% 1%
R28 R192
R36 R179 2 1 2 2 1 2
S2 2 S4 2
219-04MST 219-04MST 475 475
2K 2K GREEN GREEN
0.125W 0.125W
0.125W 0.125W
1% DS5 1% DS13
1 I1 O1 8 4 1% 1 I1 O1 8 4 1%
HSMG-C190 HSMG-C190
R37 R238
2 I2 O2 7 5 3 2 I2 O2 7 5 3 R29 R193
2 1 3 2 1 3
3 I3 O3 6 6 2K 3 I3 O3 6 6 2K
475 475
0.125W 0.125W GREEN GREEN
0.125W 0.125W
4 I4 O4 5 7 1% 4 I4 O4 5 7 1%
1% DS6 1% DS14
R38 R239 HSMG-C190 HSMG-C190
4 4
R30 R194
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
2K 2K 2 1 4 2 1 4
0.125W 0.125W
475 475
1% 1% GREEN GREEN
0.125W 0.125W
R39 R240 1% DS7 1% DS15
5 5 HSMG-C190 HSMG-C190
2K 2K R31 R195
0.125W 0.125W 2 1 5 2 1 5
1% 1%
475 475
GREEN GREEN
R40 R241 0.125W 0.125W
6 6 1% 1%
See the GEHC Myworkshop System to determine the status of this document.
DS8 DS16
2K 2K
HSMG-C190 HSMG-C190
0.125W 0.125W
1% 1% R32 R196
2 1 6 2 1 6
R41 R242
7 7 475 475
GREEN GREEN
0.125W 0.125W
2K 2K
1% 1%
0.125W 0.125W
DS9 DS17
1% 1%
HSMG-C190 HSMG-C190
C R33
2 1 7
R197
2 1 7
C
475 475
GREEN GREEN
0.125W 0.125W
1% 1%
3V3
U35
24C16
0.125W
R135
0.125W
R136
1K
1%
1K
1%
8 VCC
0.1U
16V
10%
C98
7 WP
SCL_E2PROM 6 SCL SDA 5 SDA_E2PROM
1 NC1
2 NC2
3 NC3 VSS 4
E2PROM STORAGE
D D
REV 2 01July04
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Feb 01 15:21:21 2013 table_board 4 of 12 5458763SCH 2 4 of 12
1
Approved Document - 5458763SCH_r2.pdf Page 5 of 13
2 3 4 5 6 7 8
Page 424 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1 2 3 4 5 6 7 8
3V3
3V3
1K
1%
1K
1%
1K
1%
0.1U
16V
10%
16V
10%
16V
10%
C45
10U
C47
C61
U33
1U
TL16C550CPT
RS232 INTERFACE
R139
R141
R142
0.125W
0.125W
0.125W
5 RCLK BAUDOUT_N 12 U34
A MAX3232C
A
RS1_CLOCK 14 XIN
15 XOUT RS1_DATA<7..0>
D0 43 0 16 VCC
9 CS0 D1 44 1 2 VP
10 45 2 6 J2
CS1 D2 VN
0.1U
0.1U
C91
16V
10%
16V
10%
3V3 RS1_CS 11 46
C46
C48
CS2_N D3 3
D4 47 4 0.1U 1 C1P
10% 1 1
RS1_ADDR<2..0> 0 28 A0 D5 2 5 16V 3 C1M R202 RS232_T1
C95 2 2 6 6
1 27 A1 D6 3 6 4 C2P ANGLE_LCD_RXD
0.1U RS232_R1 3 3 7 7
2 26 A2 D7 4 7 5 C2M
0 4 4 8 8
R144 16V 10% R203 5 5 9 9
RS1_RXD 7 SIN SOUT 8 11 T1IN T1OUT 14 RS232_T1
1K
1%
1K
1%
1K
1%
R138
R140
0.125W
0.125W
40 DCD_N OUT1_N 34
41 31 R200 15
RI_N OUT2_N GND
1K
1%
ANGLE_LCD_TXD PIN
24 ADS_N
RS1_RESET 35 22 STRAIGHT
MR DDIS 0
R145
STD_DENSITY
0.125W
RS1_CH_RD 19 RD1_N TXRDY_N 23
20 RD2 RXRDY_N 29
RS1_CH_WR 16 WR1_N
17 WR2 INTRPT 30 RS1_INT
R143
B 1K B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
VCC=3V3;GND=GND
24V TO 5V IO INTERFACE CONVERT
0.125W 1%
U12
MC1489A
R51
24V
3V3 TUBE_PITCHING_LM_0 13 11 TUBE_PITCHING_LM_0_74
IN O
20K
0.125W RESP_CTRL
0.1U
50V
10%
C34
12
1K
1%
1K
1%
1K
1%
1% VCC=VCC;GND=GND
R134
R148
R149
See the GEHC Myworkshop System to determine the status of this document.
0.125W
0.125W
0.125W
U12
MC1489A
0
RS1_ADDR<2..0> R52
24V
TUBE_PITCHING_LM_1 1 3 TUBE_PITCHING_LM_1_74
IN O
RESERVE 20K
0.125W RESP_CTRL
0.1U
50V
10%
C35
2
NO JOINTING 2K 0.25W 1% R204
1% VCC=VCC;GND=GND
C J43 C
2K 0.25W 1% R205
24V
ANODE_0 1
2K 0.25W 1% R47 1
CATHODE_0 2 2 U12
TUBE_PITCHING_OP_0 100 COLLECTOR_0 3
R48 3 MC1489A
EMITER_0 4
2K 0.25W 1% R49 4 R198
24V
ANODE_1
24V
5 5 RESERVE_1 4 6 RESERVE_1_74
CATHODE_1 6 6 IN O
TUBE_PITCHING_OP_1 100 COLLECTOR_1 7 20K
R50 7
0.125W RESP_CTRL
0.1U
EMITER_1
50V
10%
8
C73
5
8
1% VCC=VCC;GND=GND
PIN
STRAIGHT
WIRE_TO_BOARD
U12
MC1489A
R201
24V
RESERVE_2 10 8 RESERVE_2_74
IN O
J17 20K
0.125W RESP_CTRL
C139
0.1U
50V
10%
9
1% VCC=VCC;GND=GND
1 1
RESERVE_1 2 2
RESERVE_2 3 3
D D
PIN
REV 2 01July04
STRAIGHT
WIRE_TO_BOARD
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Feb 01 15:21:22 2013 table_board 5 of 12 5458763SCH 2 5 of 12
1
Approved Document - 5458763SCH_r2.pdf Page 6 of 13
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
VCC
VCC VCC
VCC
0.1U
16V
10%
C38
R126
C124
0.1U
C129
0.1U
16V
10%
16V
10%
R165
C135
0.1U
16V
10%
332
0.1W 332
1% 0.1W
U24 1%
4.688V U26
8
AD822 4.688V
8
VP
3 AD822
VP
R58 3
R154
A 1
VOUT 2
1 A
R127 VOUT 2
10 R166
VN
0.1U
16V
10%
C42
4.99K 10
VN
C131
0.1U
16V
10%
0.1W 0.1W 4.99K
4
0.1W 0.1W
4
1% 1% 1% 1%
R62
R158
316
316
0.1W
0.1W
1%
1%
U26
U24 1.929V
8
1.929V R153 AD822
VP
R56 AD822 TUBE_ANGLE_H 5
VP
SID_H 5 R168 3V3
R130 7
7 R156 3V3
R60 TUBE_ANGLE_M 143K 6 VOUT
SID_M 143K 6 VOUT 0.1W 100
VN
0.1W 100
VN
1% 143K 0.1W
4
1% 143K 0.1W
4
0.1W 1%
1K R169
1K R170
1K R171
1K R172
0.125W 1%
0.125W 1%
0.125W 1%
0.125W 1%
0.1W 1%
C136
C137
0.1U
50V
10%
35V
10%
1%
1U
1% R160
R64
C127
0.1U
16V
10%
100K R162
0.1U
16V
10%
C36
100K R92 0.1W
0.1W 1%
1% 100K
100K
0.1W
0.1W
B B
C133
1%
C100
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
1% U32
ADC124S101
VCC 3
See the GEHC Myworkshop System to determine the status of this document.
0.1U
16V
10%
C39 R128
C125
0.1U
C128
0.1U
16V
10%
16V
10%
R163
C134
0.1U
16V
10%
332
0.1W 332
1% 0.1W J5 J6
U25 1%
4.688V U30
8
AD822 4.688V
8
VP
3 AD822
VP
R59 3 SID_H 1 TUBE_ANGLE_H 1
1 R152 1 1
C VOUT 2 R129
1
VOUT 2
SID_M 2
3
2 TUBE_ANGLE_M 2
3
2 C
10 R164 3 3
VN
0.1U
16V
10%
C43
4.99K 10
VN
C130
0.1U
16V
10%
0.1W 0.1W 4.99K
4
0.1W 0.1W
4
1% 1% 1% 1% PIN PIN
500MW
500MW
STRAIGHT STRAIGHT
10%
2K
10%
2K
WIRE_TO_BOARD WIRE_TO_BOARD
R63
R157
R53
CW
R132
CW
316
316
0.1W
0.1W
1%
U25 1%
1.929V U30
8
8
VP
VP
R131 CON_RES_UD_D+ 5
7 R167
R61 7
CON1_LR_D 143K 6 VOUT R155
CON1_UD_D 143K 6 VOUT
0.1W 100
VN
0.1W 100
VN
1% 143K 0.1W
4
1% 143K 0.1W
4
0.1W 1%
0.1W 1%
1%
R65 1%
R159
0.1U
16V
10%
C37
100K R42
C126
0.1U
16V
10%
0.1W 100K R161
1% 0.1W
100K 1%
100K
0.1W
0.1W
C102
1%
SID&TUBE ANGLE&COLLIMATOR CONTROL AD INPUT
C132
1%
D D
REV 2 01July04
16V
16V
0.1U
0.1U
10%
10%
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Thu Jul 18 09:15:09 2013 table_board 6 of 12 5458763SCH 2 6 of 12
1
Approved Document - 5458763SCH_r2.pdf Page 7 of 13
2 3 4 5 6 7 8
Page 426 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1 2 3 4 5 6 7 8
U1
TABLE MOTION LIMIT SW & CASSETTE COMP
U3
MC1489A J8
MC1489A
R66
R76
24V
VERTICAL_STOP_SW 1 3 VERTICAL_STOP_74 UP_LIMIT_74
24V
UP_LIMIT_SW 1 3 J7
IN O 1 1
20K IN O LEFT_LIMIT_SW 2
20K 2
0.125W RESP_CTRL
0.1U
50V
10%
3
C49
2
0.125W RESP_CTRL 3
A A
0.1U
50V
10%
1
C63
2
1% VCC=VCC;GND=GND RIGHT_LIMIT_SW 4 1
1% 4 VERTICAL_STOP_SW 2
5 2
VCC=VCC;GND=GND 5 3
UP_LIMIT_SW 6 3
6 LEVEL_CW_STOP 4
7 4
7 5
DOWN_LIMIT_SW 8 5
8 INCLINE_STOP_SW 6
9 6
U1 9
U3 UD_RANGE_STOP 10
MC1489A 10
VERTICAL_OVER_SW MC1489A
R67
R77 PIN
24V
4 6 VERTICAL_OVER_74 DOWN_LIMIT_74
24V
DOWN_LIMIT_SW 4 6 STRAIGHT
IN O PIN
20K IN O WIRE_TO_BOARD
20K STRAIGHT
0.125W RESP_CTRL
0.1U
50V
10%
C50
5
0.125W RESP_CTRL WIRE_TO_BOARD
0.1U
50V
10%
C64
5
1% VCC=VCC;GND=GND
1% VCC=VCC;GND=GND
U1
U3
MC1489A
MC1489A
R68
R78 J12
24V
24V
UD_RANGE_STOP 10 8
IN O J9
20K IN O
20K 1
0.125W RESP_CTRL 1
0.1U
50V
10%
C51
9
0.125W RESP_CTRL
0.1U
50V
10%
INCLINE_OVER_SW 2
C65
9
1% VCC=VCC;GND=GND 2 1
1% POWER_GROUP=VCC=VCC;GND=GND 3 1
3 CASSTTE_IN_SW 2
VERTICAL_OVER_SW 4 2
4 3 3
B 5 5 B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
U3 MINUS_15_DEGREE_STOP 6 6
U1 7
MC1489A 7
MC1489A MINUS_15_DEGREE_STOP_74 LEVEL_CCW_STOP 8 PIN
R74 MINUS_15_DEGREE_STOP 8
R69 STRAIGHT
24V
13 11
24V
0.1U
50V
10%
C59
12
0.125W RESP_CTRL STRAIGHT
0.1U
50V
10%
C52
12
1% VCC=VCC;GND=GND
1% VCC=VCC;GND=GND WIRE_TO_BOARD
U4
MC1489A
See the GEHC Myworkshop System to determine the status of this document.
24V
1 3
MC1489A
IN O
R70 LEVEL_CW_STOP 20K
0.1U
24V
50V
10%
1 3 LEVEL_CW_STOP_74
C60
0.125W RESP_CTRL
2
IN O 1% VCC=VCC;GND=GND
20K
0.125W RESP_CTRL U4
0.1U
50V
10%
C53
1% VCC=VCC;GND=GND MC1489A
R75 SID_OPB_150CM_LM SID_OPB_150CM_LM_74 2K 0.25W 1% R212
24V
4 6
IN O 2K 0.25W 1% R207 J10
C 20K 2K 0.25W 1% R213 C
0.1U
50V
10%
24V
C44
U2 0.125W RESP_CTRL
5
MC1489A 1% VCC=VCC;GND=GND 2K 0.25W 1% R208 ANODE_2 1 2 CATHODE_2
R214 1 2
24V
R71 SID_OPB_150CM_LM 100 COLLECTOR_2 3 4 EMITER_2
U4 3 4
24V
10 8 ANODE_4 9 10 CATHODE_4
0.125W RESP_CTRL 2K 0.25W 1% R209 R215 9 10
0.1U
50V
10%
C54
0.1U
50V
10%
C62
24V
1% VCC=VCC;GND=GND
PIN
U2
STRAIGHT
MC1489A
RIBBON_CABLE_STANDARD
R72
24V
SID_OPB_105CM_LM 13 11
0.125W RESP_CTRL
0.1U
50V
10%
C55
IN O VCC
1% VCC=VCC;GND=GND 20K
0.1U
50V
10%
C67
0.125W 12 RESP_CTRL
1% VCC=VCC;GND=GND
U2
MC1489A
0.1U
0.1U
0.1U
0.1U
50V
10%
50V
10%
50V
10%
50V
10%
C57
C58
C66
C40
R73 RIGHT_LIMIT_74
24V
RIGHT_LIMIT_SW 13 11
D IN O
D
20K
0.125W RESP_CTRL
0.1U
50V
10%
C56
REV 2 01July04
12
1% VCC=VCC;GND=GND
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Feb 01 15:21:22 2013 table_board 7 of 12 5458763SCH 2 7 of 12
1
Approved Document - 5458763SCH_r2.pdf Page 8 of 13
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
U5
U7 MC1489A
MC1489A
R82
R97
TABLE SIDE&COMPRESS LM&SID LM&TUBE UNLOCK
24V
TILT_RISE_SIDE_SW TILT_RISE_SIDE_74 XRAY_IRC_SW 10 8XRAY_IRC_74
24V
1 3
IN O
IN O 20K
20K
0.125W RESP_CTRL
0.1U
0.1U
50V
10%
50V
10%
C68
C82
9
0.125W RESP_CTRL
2
1% VCC=VCC;GND=GND
1% VCC=VCC;GND=GND U10
U7 MC1489A
MC1489A R104 SID_UP_OVER_74
U5
24V
R93 PDU_STATE PDU_STATE_74 SID_UP_OVER 4 6
MC1489A
24V
13 11 IN O
R83 TILT_FALL_SIDE_SW TILT_FALL_SIDE_74 20K J351
IN O
A A
24V
4 6 20K 0.125W RESP_CTRL
0.1U
50V
10%
C92
5
0.1U
50V
10%
C78
IN O 0.125W RESP_CTRL 1% VCC=VCC;GND=GND
12
20K
24V
24V
1% 1 1 2 2
0.125W RESP_CTRL
0.1U
50V
10%
3 4
C69
5
VCC=VCC;GND=GND 3 4
1% VCC=VCC;GND=GND U8 U10 5 6
5 6
MC1489A MC1489A 7 8
U5 7 8
R94 SID_UP_SIDE_74 R105 9 10 LAMP_SIDE
MC1489A 9 10
24V
24V
SID_UP_SIDE_SW 1 3 SID_DOWN_STOP 10 8 SID_DOWN_STOP_74
R84 TILT_RISE_SIDE_SW 11 11 12 12 TILT_FALL_SIDE_SW
TUBE_UP_SIDE_74 IN O IN O
24V
0.1U
50V
10%
TOP_RIGHT_SIDE_SW 15 16 TOP_LEFT_SIDE_SW
C79
IN O 0.125W RESP_CTRL 0.125W RESP_CTRL 15 16
0.1U
50V
10%
C93
2
9
20K SID_UP_SIDE_SW 17 18 SID_MID_SIDE_SW
1% VCC=VCC;GND=GND 1% VCC=VCC;GND=GND 17 18
0.1U
50V
10%
C70
0.125W RESP_CTRL SID_DOWN_SIDE_SW 19 20 TABLE_EM_SW
9
19 20
1% VCC=VCC;GND=GND EMERGENCY_LED 21 22 CONSOLE_EM_SW
21 22
U5 U8 U10 23 24 ANGLE_LCD_BUSY
23 24
MC1489A MC1489A ANGLE_LCD_RXD 25 26 ANGLE_LCD_TXD
MC1489A 25 26
R95 SID_MID_SIDE_SW R106
R85
24V
24V
TUBE_DOWN_SIDE_74 4 6 SID_MID_SIDE_74 TUBE_LEVEL_DETECTOR 13 11 TUBE_LEVEL_DETECTOR_74
24V
TUBE_DOWN_SIDE_SW 13 11
IN O IN O
IN O 20K 20K PIN
20K
0.125W RESP_CTRL 0.125W RESP_CTRL STRAIGHT
0.1U
0.1U
50V
10%
50V
10%
C75
C80
C96
5
12
0.125W RESP_CTRL
12
1% VCC=VCC;GND=GND 1% VCC=VCC;GND=GND RIBBON_CABLE_STANDARD
0.1U
50V
10%
1% VCC=VCC;GND=GND
U8 VCC
U6 MC1489A J16
MC1489A R96SID_DOWN_SIDE_SW
R86
24V
10 8 SID_DOWN_SIDE_74
24V
TOP_LEFT_SIDE_SW 1 3TOP_LEFT_SIDE_74
IN O 1 1
IN O 20K
24V
20K 2 2
B B
0.1U
50V
10%
C81
0.125W RESP_CTRL
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
C101
0.1U
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
PDU_STATE 3
C71
C89
C90
C94
C97
C99
9
0.125W RESP_CTRL 3
2
1% VCC=VCC;GND=GND CR1
1% VCC=VCC;GND=GND
GBLC05C
U6
U8 PIN
MC1489A
MC1489A STRAIGHT
R87
WIRE_TO_BOARD
24V
24V
IN O 13 11
20K
IN O
0.1U
50V
10%
C72
0.1U
4.99K
50V
10%
C83
12
0.1W
1% TUBE_LEVEL_DETECTOR 2 2
R55
VCC=VCC;GND=GND 3
See the GEHC Myworkshop System to determine the status of this document.
1%
3
VCC
U9
U6 MC1489A
PIN
MC1489A R99 TUBE_PITCHING_DETECTOR TUBE_PITCHING_DETECTOR_74 STRAIGHT
24V
R88 R147 1 3
WIRE_TO_BOARD
24V
EMERGENCY_LED 10 8 EMERGENCY_74 IN O
20K R133 J42
IN O TUBE_UNLOCK_SW1_74
20K 20K 0.125W RESP_CTRL
0.1U
50V
10%
C84
2
0.125W 0.125W RESP_CTRL 1% VCC=VCC;GND=GND
9
0 J341
0.1U
50V
10%
1% 1% VCC=VCC;GND=GND P_GND 1 1
C7
TUBE_UNLOCK_SW1 R151 2 2
U9
C MC1489A 0 P_GND
3
4
3 1
3
1 2 2
P_GND
4
P_GND
TILT_RISE_SIDE_SW
C
4 3 4
R100 R218 5 5 6 TILT_FALL_SIDE_SW
U6 5 5 6
24V
TUBE_UNLOCK_SW1 4 6 TUBE_UNLOCK_SW1_74
MC1489A R216 6 6 7 7 8 8
IN O TUBE_UNLOCK_SW2 TUBE_PITCHING_DETECTOR 7 TUBE_DOWN_SIDE_SW 9 10 TUBE_UP_SIDE_SW
20K 0 7 9 10
R89 8 11 12 TOP_LEFT_SIDE_SW
0.125W RESP_CTRL 8 11 12
0.1U
24V
50V
10%
COM_UP_IRC_SW 13 11COM_UP_IRC_74
C86
5
0 TOP_RIGHT_SIDE_SW 13 14
1% VCC=VCC;GND=GND 13 14
IN O R217 COM_UP_IRC_SW 15 16 COM_DOWN_IRC_SW
20K TUBE_UNLOCK_SW2_74 15 16
0.125W RESP_CTRL PIN FOOT_IRC_SW 17 17 18 18
0.1U
50V
10%
C76
12
U9
VCC
1% R54 0.1W 0 STRAIGHT XRAY_IRC_SW 19 19 20 20 SID_UP_SIDE_SW
MC1489A SID_DOWN_SIDE_SW 21 22
VCC=VCC;GND=GND WIRE_TO_BOARD 21 22
R101 R219
CR2
SID_MID_SIDE_SW 23 23 24 24 CON_RES_TEMP-
24V
24V
MC1489A 0.125W RESP_CTRL CON_RES_UD_TEMP+ 29 29 30 30
0.1U
50V
10%
C85
24V
R90 1% VCC=VCC;GND=GND 31 31 32 32
24V
24V
24V
37 37 38 38
0.1U
50V
10%
C77
39 40
1% VCC=VCC;GND=GND R102 SID_MIDDLE_STOP CONSOLE_EM_SW 41 42 CONSOLE_EM_SW
41 42
24V
13 11 SID_MIDDLE_STOP_74
43 43 44 44
IN O 1 2 COMPRESS_UP_STOP 45 46
20K 1 2 45 46
3 4 COMPRESS_UP_OVER RESERVE +12V_GND 47 48 +12V_GND
U7 0.125W RESP_CTRL 3 4 47 48
0.1U
50V
10%
C87
12
MC1489A 1% 5 5 6 6 SID_DOWN_STOP +12V 49 49 50 50 +12V
7 8 SID_DOWN_OVER RESERVE
R91 VCC=VCC;GND=GND 7 8
24V
REV 2 01July04
DUAL_ROW_LATCHING
24V
1% VCC=VCC;GND=GND 1 3 SID_UP_STOP_74
IN O
20K PIN
0.125W RESP_CTRL STRAIGHT
0.1U
50V
10%
C88
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Feb 01 15:21:23 2013 table_board 8 of 12 5458763SCH 2 8 of 12
1
Approved Document - 5458763SCH_r2.pdf Page 9 of 13
2 3 4 5 6 7 8
Page 428 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1 2 3 4 5 6 7 8
U28
U11
MC1489A
R115
MC1489A
COM_UP_CONSOLE_74
CONSOLE CONTROL SW COMP
24V
COM_UP_CONSOLE_SW 1 3
R107 R181 NO JOINTING
IN O
24V
TILT_RISE_CONSOLE_SW 1 3TILT_RISE_CONSOLE_74 20K R189NONOJOINTING
JOINTING CON_RES_LR+
IN O 0.125W RESP_CTRL CON1_LR CON_RES_LR_TEMP+
C111
0.1U
50V
10%
2
20K R176 0
1% VCC=VCC;GND=GND CON1_LR_TEMP CON_RES_LR_D+
0.125W RESP_CTRL R174 0
C103
0.1U
50V
10%
2
1% VCC=VCC;GND=GND CON1_LR_D
A 0 A
0 R182 NO JOINTING
R180 NO JOINTING CON_RES_UD+
CON1_UD
CON_RES_UD_TEMP+
U28 R177 0
MC1489A R175 0 CON1_UD_TEMP CON_RES_UD_D+
U11 CON1_UD_D
R116
MC1489A 0
24V
COM_DOWN_CONSOLE_SW 4 6 COM_DOWN_CONSOLE_74 0
R108
IN O R183
24V
C112
0.1U
50V
10%
CON_RES_TEMP-
5
20K
1% VCC=VCC;GND=GND R178 0
0.125W RESP_CTRL
C104
0.1U
50V
10%
5
1% VCC=VCC;GND=GND
0
J331
U28
MC1489A
U11 P_GND 1 2 P_GND
R117 1 2
MC1489A
24V
FOOT_CONSOLE_SW 10 8FOOT_CONSOLE_74 3 3 4 4 TILT_RISE_CONSOLE_SW
R109 SPARE_CONSOLE_SW 5 6 TILT_FALL_CONSOLE_SW
IN O 5 6
24V
C113
0.1U
50V
10%
TOP_LEFT_CONSOLE_SW 9 10TOP_RIGHT_CONSOLE_SW
9
20K 9 10
1% VCC=VCC;GND=GND 11 12 TUBE_DOWN_CONSOLE_SW
0.125W RESP_CTRL 11 12
C105
0.1U
50V
10%
9
1% VCC=VCC;GND=GND TUBE_UP_CONSOLE_SW 13 13 14 14
COM_UP_CONSOLE_SW 15 15 16 16 COM_DOWN_CONSOLE_SW
FOOT_CONSOLE_SW 17 17 18 18
XRAY_CONSOLE_SW 19 19 20 20 SID_DOWN_CONSOLE_SW
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
U28 SID_MID_CONSOLE_SW 21 21 22 22
U11 SID_UP_CONSOLE_SW 23 24 CON_RES_TEMP-
MC1489A 23 24
MC1489A CON1_LR_TEMP 25 26 CON_RES_LR_TEMP+
R118 25 26
R110
24V
TUBE_UP_CONSOLE_74 XRAY_CONSOLE_SW 13 11XRAY_CONSOLE_74 CON_RES_TEMP- 27 27 28 28 CON1_UD_TEMP
24V
TUBE_UP_CONSOLE_SW 13 11
24V
IN O CON_RES_UD_TEMP+ 29 29 30 30
IN O 20K
24V
20K 31 31 32 32
0.125W RESP_CTRL
C114
0.1U
50V
10%
33 34
12
0.125W RESP_CTRL 33 34
C106
0.1U
50V
10%
12
24V
24V
37 37 38 38
U29 COM_LED 39 40 COM_LED
39 40
MC1489A CONSOLE_EM_SW 41 42 CONSOLE_EM_SW
41 42
R119 SID_DOWN_CONSOLE_SW SID_DOWN_CONSOLE_74 43 44
See the GEHC Myworkshop System to determine the status of this document.
43 44
24V
U27 1 3
45 45 46 46
MC1489A IN O +12V_GND 47 48 +12V_GND
20K 47 48
R111 TUBE_DOWN_CONSOLE_74 +12V 49 50 +12V
0.125W RESP_CTRL 49 50
C115
0.1U
24V
50V
10%
TUBE_DOWN_CONSOLE_SW 1 3
2
1% VCC=VCC;GND=GND
IN O
20K
0.125W RESP_CTRL PIN
C107
0.1U
50V
10%
SID_MID_CONSOLE_SW 4 6
C C
24V 24V
IN O 1 1 POWER_RELAY_24V 1 1 1 1
U27 20K 2 2 CONSOLE_EM_SW 2
2 2 2
MC1489A 0.125W RESP_CTRL
C116
0.1U
50V
10%
3 3 3
5
3 3 3
R112 1% VCC=VCC;GND=GND EMERG_SW_RELAY 4 4
24V
TOP_LEFT_CONSOLE_SW 4 6 TOP_LEFT_CONSOLE_74
IN O
20K PIN PIN
0.125W RESP_CTRL PIN STRAIGHT STRAIGHT
C108
0.1U
50V
10%
10 8 SID_UP_CONSOLE_74
U27 IN O
20K EMERG_SW_RELAY 1
MC1489A COILP
0.125W RESP_CTRL
C138
0.1U
50V
10%
10
9
R113 D2 COILN
1% VCC=VCC;GND=GND
24V
0.1U
50V
10%
K 3 EMERG_SW_RELAY TABLE_EM_SW 8 9
9
COM<0> CLOSED<0>
1% VCC=VCC;GND=GND 2 A2 7 EMERG_SW_RELAY
OPEN<0>
70V
U27
R114
MC1489A EMERGENCY SW LOGIC
24V
SPARE_CONSOLE_SW 13 11 SPARE_CONSOLE_74
D IN O VCC D
20K
0.125W RESP_CTRL
RESERVE,NO JOINTING
C110
0.1U
50V
10%
12
REV 2 01July04
1% VCC=VCC;GND=GND
C117
0.1U
C118
0.1U
C119
0.1U
0.1U
50V
10%
50V
10%
50V
10%
50V
10%
C41
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Feb 01 15:21:24 2013 table_board 9 of 12 5458763SCH 2 9 of 12
1
Approved Document - 5458763SCH_r2.pdf Page 10 of 13
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Q1
ULN2003A 24V
TABLE MOTOR CONTORL OUTPUT
24V I74
COM 9
BUZZER Q4 R124 P1
A COMPRESS_LED_CONSOLE
MOTOR_RESERVE_MOTOR
1
2
B<6> C<6> 16
15
COM_LED
MOTOR_RESERVE ULN2003A
A
B<5> C<5>
LAMP_SIDE_CPLD 3 14 LAMP_SIDE BUZZER
B<4> C<4> 0
COMPRESS_CTRL_OUT_1 4 B<3> C<3> 13 COMPRESS_UP 0.125W
COMPRESS_CTRL_OUT_0 5 12 COMPRESS_DOWN COM 9 1
B<2> C<2> 1 16 BUZZER_OUT 0% 2
TOP_CTRL_OUT_1 6 11 TOP_RIGHT B<6> C<6>
B<1> C<1> TUBE_MOVE_CTRL_OUT_2 2 15 TUBE_SPARE J15
TOP_CTRL_OUT_0 7 10 TOP_LEFT B<5> C<5>
B<0> C<0> TUBE_MOVE_CTRL_OUT_1 3 14 TUBE_FALL
B<4> C<4>
TUBE_MOVE_CTRL_OUT_0 4 B<3> C<3> 13 TUBE_RISE
E 8 TOP_LEFT 1 1 2 2 TOP_RIGHT
TILT_CTRL_OUT_2 5 B<2> C<2> 12 TILT_SPARE
COMPRESS_DOWN 3 3 4 4 COMPRESS_UP
TILT_CTRL_OUT_1 6 B<1> C<1> 11 TILT_FALL
TILT_RISE 5 5 6 6 TILT_FALL
TILT_CTRL_OUT_0 7 B<0> C<0> 10 TILT_RISE
TILT_SPARE 7 7 8 8 TILT_IVT_DO
TUBE_RISE 9 9 10 10 TUBE_FALL
E 8
TUBE_SPARE 11 11 12 12 TUBE_IVT_DO
24V
24V
13 13 14 14
15 15 16 16
17 17 18 18
Q2 19 20
24V 19 20
ULN2003A VCC COMPRESS_DOWN1 21 22 TUBE_SPEED_UP
21 22
TUBE_SPEED_DOWN 23 23 24 24 SID_IO_IN1
Q3 SID_IO_IN2 25 25 26 26 SID_IO_IN3
COM 9
ULN2003A 24V SID_IO_IN4 27 27 28 28 SID_IO_IN5
COMPRESS_DOWN1_MOTOR 1 B<6> C<6> 16 COMPRESS_DOWN1
SID_IO_IN6 29 29 30 30 SID_IO_OUT1
TUBE_SPEED_UP_MOTOR 2 B<5> C<5> 15 TUBE_SPEED_UP
31 31 32 32 TUBE_LOCK
TUBE_SPEED_DOWN_MOTOR 3 B<4> C<4> 14 TUBE_SPEED_DOWN
C123
0.1U
50V
10%
COM 9 MOTOR_RESERVE 33 33 34 34
SID_MOTOR_OUT_0 4 B<3> C<3> 13 SID_IO_IN1 POWER_RELAY_TIMER_CPLD POWER_RELAY_TIMER
1 B<6> C<6> 16
SID_MOTOR_OUT_1 5 B<2> C<2> 12 SID_IO_IN2
B 2 B<5> C<5> 15 B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
E 8
U31
MC1489A
R121
See the GEHC Myworkshop System to determine the status of this document.
24V
TILT_IVT_DO 13 11 TILT_IVT_DO_74
IN O
20K D3
0.125W RESP_CTRL BAV70LT1
POWER_ON ORDER CONTROL&EMERGENCY SWITCH CONTROL
12
1% VCC=VCC;GND=GND
1 A1
C120
0.1U
50V
10%
K 3
2 A2
K3
TQ2SA-24V 70V
U31 24V
C MC1489A 1 COILP
C
R122 POWER_RELAY_TIMER 10 COILN
24V
TUBE_IVT_DO 1 3 TUBE_IVT_DO_74 K4 K5
IN O 3 COM<1> CLOSED<1> 2 TQ2SA-24V TQ2SA-24V
20K 4
OPEN<1>
0.125W RESP_CTRL TABLE_EM_SW 8 9
2
COM<0> CLOSED<0>
1% VCC=VCC;GND=GND 7 1 TABLE_EM_SW 1
OPEN<0> COILP COILP
C121
0.1U
50V
10%
10 COILN 10 COILN
TABLE_EM_SW 3 COM<1> CLOSED<1> 2 3 COM<1> CLOSED<1> 2
OPEN<1> 4 OPEN<1> 4
TABLE_EM_SW 8 COM<0> CLOSED<0> 9 8 COM<0> CLOSED<0> 9 EMERGENCY_LED
U31 7 POWER_RELAY+ 7
OPEN<0> OPEN<0>
MC1489A
R123
24V
SID_IO_OUT1 4 6 SID_IO_OUT1_74
IN O
20K
0.125W RESP_CTRL
5
1% VCC=VCC;GND=GND
C122
0.1U
50V
10%
J3
U31
MC1489A POWER_RELAY+
R184 1 1
TABLE_EM_SW TABLE_EM_SW_74
10 8 2 2
D 20K
IN O 3 3 D
0.125W RESP_CTRL
9
REV 2 01July04
1% VCC=VCC;GND=GND
PIN
STRAIGHT
WIRE_TO_BOARD
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Feb 01 15:21:23 2013 table_board 10 of 12 5458763SCH 2 10 of 12
1
Approved Document - 5458763SCH_r2.pdf Page 11 of 13
2 3 4 5 6 7 8
Page 430 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1 2 3 4 5 6 7 8
A A
VCC
4 4 DO-TO_CONSOLE<15..0> 0 9 9 10 10 1 DO-TO_CONSOLE<15..0>
R3 R5 2 11 11 12 12 3
2 1 4 13 13 14 14 5
4
PIN 6 15 15 16 16 7
2K 2K 8 17 18 9
GREEN STRAIGHT 17 18
0.125W 0.125W 10 19 20 11
MATE_N_LOK 19 20
1% 1% 12 21 22 13
21 22
14 23 23 24 24 15
COL-CPLD<7..0> 0 25 25 26 26 1 COL-CPLD<7..0>
2 27 27 28 28 3 NO JOINTING
4 29 30 5 R236
29 30
B 6 31 31 32 32 7 DA_LDAC_N B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
VCC
VCC
45 45 46 46
0.125W 0.125W 0
100U
100U
47 48 CON_RES_UD+
35V
20%
35V
20%
47 48
C1
C2
1% 1% 49 50 0
49 50
TP0 R233
R6 COL_UD_AD
See the GEHC Myworkshop System to determine the status of this document.
0
TIN PIN
R9 STRAIGHT
0
RIBBON_CABLE_STANDARD
0.125W
R7
G24V 0% 2K
0.125W
0 1%
0.125W
0%
C C
P_GND
D D
REV 2 01July04
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Feb 01 15:21:23 2013 table_board 11 of 12 5458763SCH 2 11 of 12
1
Approved Document - 5458763SCH_r2.pdf Page 12 of 13
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
A A
1K R220
1K R221
1K R222
1K R223
0.125W 1%
0.125W 1%
0.125W 1%
0.125W 1%
C141
C142
0.1U
50V
10%
35V
10%
1U
K 3
K 3
BAV70LT1
BAV70LT1
70V
70V
U36
1 A1
2 A2
1 A1
2 A2
ADC124S101
See the GEHC Myworkshop System to determine the status of this document.
D4
D5
2 VA SCLK 10 AD_SCLK_COL
R224
COL_FED_UD_AD R225 7 IN1 CS_N 1 AD_CS_N_COL
COL_FED_LR_AD R226 6 IN2
COL_UD_AD 100 5 8 AD_DIN_COL
R227 IN3 DIN
COL_LR_AD 0.1W 100 4 9 AD_DOUT_COL
IN4 DOUT
1% 100 0.1W
0.1W 1% 100 3
GND
1% 0.1W
0.125WC143
0.1U
C145
0.1U
16V
10%
16V
10%
500MW
1%
C C
10%
500MW
1K
0.125W
R234
R235
10%
1K
1K
1%
1K
1%
R229
CW
C144
0.1U
C146
0.1U
R228
16V
10%
16V
10%
CW
D D
REV 2 01July04
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Feb 01 15:21:23 2013 table_board 12 of 12 5458763SCH 2 12 of 12
1 2
Approved Document - 5458763SCH_r2.pdf Page 13 of 13
3 4 5 6 7 8
Page 432 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1.4 Motor Board (5444620)
1 2 3 4
B
to the ECR/ECO Process.
ent.
1 2 3 4 5 6 7 8
A J6 A
TOP_LEFT 1 1 2 2 TOP_RIGHT
COMPRESS_UP 3 3 4 4 COMPRESS_DOWN
TILT_RISE 5 5 6 6 TILT_FALL
TILT_SPARE 7 7 8 8 TILT_INVERTER_DO
MATE_N_LOK
TUBE_UP 9 9 10 10 TUBE_DOWN
STRAIGHT
TUBE_SPARE 11 11 12 12 TUBE_INVERTER_DO
24V
PIN
13 14
24V
13 14
15 15 16 16
1
2
17 17 18 18 24V_ISOLATION
J8
19 19 20 20
21 22
1
2
21 22
23 23 24 24 SID_IO IN1
SID_IO IN2 25 25 26 26 SID_IO IN3
SID_IO IN4 27 27 28 28 SID_IO IN6
SID_IO IN7 29 29 30 30 SID_IO OUT1 C1
SID_IO OUT2 31 31 32 32 TUBE_LOCK K6
33 33 34 34 G2RL-1A DC24
1000U
63V
PIN 20%
STRAIGHT
RIBBON_CABLE_STANDARD R7
MATE_N_LOK
B STRAIGHT B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
4.7K
PIN
0.25W
1%
4 3 2 2
1 1
24V
1
TUBE_LOCK 5 J9
R8
10W
51
5%
See the GEHC Myworkshop System to determine the status of this document.
DSS10-01A
100V
D4
C C
P P P P
D D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
Wed Aug 28 14:12:06 2013 motor_board 2 of 4 5444620SCH 2 2 of 4
1
Approved Document - 5444620SCH_r2.pdf Page 3 of 5
2 3 4 5 6 7 8
Page 434 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1 2 3 4 5 6 7 8
R20
6.81K
R11 U2
0.125W
TCMT4100
24V 1%
6.81K
U3 R21
0.125W 1 16 TILT_INVERTER_+24V
TCMT4100
24V 1%
6.81K
R12
1 16 TUBE_INVERTER_+24V 0.125W
R1
1%
A 6.81K
TILT_RISE 2 15 TILT_INVERTER_DI0 A
0.125W 20K
R4
TUBE_UP 1% 2 15 TUBE_INVERTER_DI0 0.125W
1%
R22
20K
0.125W
1% 6.81K
U2
0.125W
R13 TCMT4100
24V 1%
R23
6.81K 3 14
U3
0.125W
TCMT4100
24V 1% 6.81K
0.125W
R14 R2
3 14 TILT_FALL 1% 4 13 TILT_INVERTER_DI1
6.81K 20K
0.125W 0.125W
R5
TUBE_DOWN 1% 4 13 TUBE_INVERTER_DI1 1%
20K
R24
0.125W
1%
6.81K
R15 U2
0.125W
TCMT4100
1%
B 24V B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
6.81K
U3 R25
0.125W 5 12
TCMT4100
24V 1%
6.81K
R16
5 12 0.125W
R3
TILT_SPARE 1% 6 11 TILT_INVERTER_DI2 TILT_INVERTER_G24
6.81K
0.125W 20K
R6
TUBE_SPARE 1% 6 11 TUBE_INVERTER_DI2 TUBE_INVERTER_G24 0.125W
1%
20K
See the GEHC Myworkshop System to determine the status of this document.
0.125W
1%
J4
1 1 2 2TILT_INVERTER_DO
C
TILT & UP/DOWN INVERTER CONTROL TILT_INVERTER_DI0
TILT_INVERTER_DI2
TILT_INVERTER_G24
3
5
7
9
3
5
7
4
6
8
4TILT_INVERTER_DI1
6TILT_INVERTER_+24V
8
10 C
9 10
PIN
STRAIGHT
RIBBON_CABLE_STANDARD
J5
1 1 2 2TUBE_INVERTER_DO
TUBE_INVERTER_DI0 3 3 4 4TUBE_INVERTER_DI1
TUBE_INVERTER_DI2 5 5 6 6TUBE_INVERTER_+24V
TUBE_INVERTER_G24 7 7 8 8
9 9 10 10
PIN
STRAIGHT
D RIBBON_CABLE_STANDARD D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
Wed Aug 28 14:12:07 2013 motor_board 3 of 4 5444620SCH 2 3 of 4
1
Approved Document - 5444620SCH_r2.pdf Page 4 of 5
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
K1
24V G6B_2114P_US24VDC
TOP_LEFT
8
1
COILP
J1 TOP & SID & COMPRESS MOTOR CONTORL
COILN
220VAC 1 1
A TOP_MOTOR1- 3
6
OPEN1 OPEN2 4
5
0VAC 110VAC
0VAC
2
3
2 A
CLOSED1 CLOSED2 3
4 4
P
PIN
STRAIGHT R30
MATE_N_LOK
K2 R38
24V 6.81K
G6B_2114P_US24VDC U1
0.125W
TCMT4100
1% 6.81K
U4
8 0.125W
COILP R31 R34 TCMT4100
1%
24V
TOP_RIGHT 1 COILN 1 16 ENABLE INPUT[IN1]
R39 R46
6.81K 100
24V
TOP_MOTOR2- 3 OPEN1 OPEN2 4 0VAC J2 1 16 PROGRAMMABLE INPUT[IN6]
6 5 0.125W 1% 0.125W
CLOSED1 CLOSED2
SID_IO IN1 2 15 1% SIGNAL GROUND 6.81K 100
220VAC 1 0.125W 1% 0.125W
1
TOP_MOTOR1- 2 SID_IO IN6 2 15 1% SIGNAL GROUND
2 R32
TOP_MOTOR2- 3 3
6.81K
U1 R40
0.125W
K3 PIN TCMT4100
24V 1%
G6B_2114P_US24VDC STRAIGHT
6.81K
MATE_N_LOK R33 R35 U4
0.125W
B B
24V
3 14 PROGRAMMABLE INPUT[IN2] TCMT4100
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
8 1%
COILP
COMPRESS_UP 1 6.81K 100
COILN R41 R47
0.125W 1% 0.125W
24V
3 14 PROGRAMMABLE INPUT[IN7]
COMPRESS_MOTOR1- 3 4 0VAC SID_IO IN2 4 13 1% SIGNAL GROUND
OPEN1 OPEN2
6 5 6.81K 100
CLOSED1 CLOSED2
0.125W 1% 0.125W
R26
SID_IO IN7 4 13 1% SIGNAL GROUND
6.81K
U1
0.125W
J3 TCMT4100
1%
See the GEHC Myworkshop System to determine the status of this document.
K5 R27 R36
24V
24V G6B_2114P_US24VDC 110VAC 1 1 5 12 PROGRAMMABLE INPUT[IN3]
COMPRESS_MOTOR1- 2 2
COMPRESS_MOTOR2- 3 6.81K 100
3
8 0.125W 1% 0.125W
COILP R48
COMPRESS_DOWN 1 SID_IO IN3 6 11 1% SIGNAL GROUND
COILN R42
PIN
COMPRESS_MOTOR2- 3 4 0VAC 6.81K
OPEN1 OPEN2 STRAIGHT U4
6 5 100 0.125W
CLOSED1 CLOSED2 MATE_N_LOK R28 TCMT4100
0.125W 1% 1%
5V-ACJ
R43 R49
C 6.81K 5 12 C
24V
U1
0.125W
TCMT4100
1% 100 6.81K
0.125W 1% 0.125W 1%
R29 R37
24V
7 10 PROGRAMMABLE INPUT[IN4] PROGRAMMABLE OUTPUT[OUT1] 6 11 SID_IO OUT1
6.81K 100
D1 R50
0.125W 1% 0.125W
BAV70LT1 R44
SID_IO IN4 8 9 1% SIGNAL GROUND
TOP_LEFT 1 A1 6.81K
U4
K 3 100 0.125W
24V
TCMT4100
TOP_RIGHT 2 A2 0.125W 1% 1%
5V-ACJ
R45 R51
70V 7 10
24V
D2 J7
BAV70LT1
100 6.81K
COMPRESS_UP 1 A1 ENABLE INPUT[IN1] 1 2 SIGNAL GROUND 0.125W 1% 0.125W 1%
1 2
K 3 PROGRAMMABLE INPUT[IN2] 3 4 SIGNAL GROUND 8 9 SID_IO OUT2
24V
3 4 PROGRAMMABLE OUTPUT[OUT2]
COMPRESS_DOWN 2 A2 PROGRAMMABLE INPUT[IN3] 5 5 6 6 SIGNAL GROUND
PROGRAMMABLE INPUT[IN4] 7 7 8 8 SIGNAL GROUND
70V PROGRAMMABLE INPUT[IN6] 9 10 SIGNAL GROUND
9 10
PROGRAMMABLE INPUT[IN7] 11 11 12 12 SIGNAL GROUND
PROGRAMMABLE OUTPUT[OUT1] 13 14
5V-ACJ
13 14
D3 PROGRAMMABLE OUTPUT[OUT2] 15 15 16 16
BAV70LT1 17 17 18 18
19 19 20 20
D 1 A1
K 3
D
24V
TUBE_LOCK 2 A2 PIN
REV 2 01July04
STRAIGHT
70V
RIBBON_CABLE_STANDARD
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
Wed Aug 28 14:12:08 2013 motor_board 4 of 4 5444620SCH 2 4 of 4
1
Approved Document - 5444620SCH_r2.pdf Page 5 of 5
2 3 4 5 6 7 8
Page 436 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1.5 Xray Board (5440559)
1 2 3 4 5 6 7 8
GENERAL NOTES:
REVISION ECR/ECO DATE SIGN OFF 1. THE VARIATION AND VERSION FOR THIS PWA IS
A 1 18-DEC-12 WANG ZHIGUO 5440559 A. A
2 2. THIS COVER SHEET CONTROLS THE REVISION STATUS
OF THE ENTIRE DOCUMENT. THE REVSION OF ALL
SHEETS OF THIS DOCUMENT WILL BE AT THE SAME
LEVEL.
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
See the GEHC Myworkshop System to determine the status of this document.
C C
D D
REV 2 01July04
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Dec 21 14:50:08 2012 xray_board 1 of 6 5440559SCH 1 1 of 6
1 2
Approved Document - 5440559SCH_r1.pdf Page 2 of 7
3 4 5 6 7 8
1 2 3 4 5 6 7 8
0.125W
R49
13 VP
1K
A 10000P
50V C
3 VN A
BAS116
B 2
75V
EN
Q1 COL-CPLD<2..0> 0 1
R17 R22 A0
D9
MJD31C 1 16
R29 E A1
MOT_UD+ 2 15 A2
2MEG 1MEG +12V
0.125W 0.125W 10K COL_FED_UD 4 8 UD_CONTROL
S1 D
0.125W COL_UD 5
R35 S2
BAS116
TP1
+12V 6
75V
R13 CON1_UD S3
UD_CONTROL 7
4
DIGITAL_CTRL_UD
TIN
S4
D5
AR1 1K
VCC
12 S5
20K LM324 0.125W
BAS116
D3
10 R27 11 S6
BAS116
0.125W
0.1U
75V
50V
8 10
C12
75V
S7
9 VOUT R36 9 S8 GND 14
D1
49.9
TP2
GND
R14
COL_FED_UD 0.125W
TIN
BAS116
1K VCC -12V +12V
75V
11
U13
20K -12V 0.125W
R18 R23 DG408
D6
0.125W -12V +12V
R30
0.125W
R50
2MEG 1MEG MOT_UD- 13 VP
1K
0.125W 0.125W -12V
3 VN
C16 10K E
BAS116
0.125W B 2
75V
EN
Q2 COL-CPLD<5..3> 1
D10
3 A0
MJD32C
B 10000P
C 4 16 A1 B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
50V 5 15 A2
-12V
COL_FED_LR 4 S1 D 8 LR_CONTROL
-12V COL_LR 5 S2
C15 +12V CON1_LR 6 S3
DIGITAL_CTRL_LR 7 S4
+12V 12 S5
10000P 11 S6
50V C 10 S7
BAS116
B 9 14
75V
S8 GND
Q3
D11
R20 R25
See the GEHC Myworkshop System to determine the status of this document.
MJD31C
R31 E
MOT_LR+
2MEG 1MEG +12V
0.125W 0.125W 10K +12V
+12V 0.125W -12V
BAS116
VCC
75V
R15 U3
COL_FED_LR -12V +12V DG409
4
D7
AR1
20K VCC LM324
BAS116
D4
5 R28
BAS116
0.125W
0.1U
75V
50V
7 14
C13
75V
VP
0.125W
R60
6 VOUT 3 VN
C C
1K
D2
49.9
GND
R16
LR_CONTROL 0.125W 2 EN
BAS116
75V
11
D8
0.125W COL-CPLD<7> 16 A1
R32
2MEG 1MEG MOT_LR- CON_RES_UD1 4 8CON_RES_UD+
-12V S1A DA
0.125W 0.125W CON_RES_UD2 5
E S2A
C17 10K CON_RES_UD3 6 S3A
BAS116
0.125W B 7
75V
S4A
Q4
D12
+12V 10000P MJD32C CON_RES_LR1 13 9CON_RES_LR+
C S1B DB
50V CON_RES_LR2 12 S2B
+12V CON_RES_LR3 11 S3B
-12V 10 S4B GND 15
R11 R19 -12V
COL_RES+
3.16K 49.9
0.125W 0.125W
VR9 R56
R12 R26 R34
CW CON_RES_UD1 CW CON_RES_LR1 R33 R37
COL_RES-
3.16K 15.8K 5K 500MW 15.8K 5K 500MW
0.125W 0.1W 0.1W 49.9 3.16K
0.1% VR10 0.1% R57 0.125W 0.125W
D CW CON_RES_UD2 CW CON_RES_LR2
D
R51 R38
-12V
REV 2 01July04
5K 500MW 5K 500MW CON_RES- -12V
VR11 R58 2.37K 3.16K
CW CON_RES_UD3 CW CON_RES_LR3 0.125W 0.125W
1% GE Healthcare
5K 500MW 5K 500MW Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Dec 21 14:35:31 2012 xray_board 2 of 6 5440559SCH 1 2 of 6
1
Approved Document - 5440559SCH_r1.pdf Page 3 of 7
2 3 4 5 6 7 8
Page 438 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1 2 3 4 5 6 7 8
VCC
POWER LED
+12V
DS1
HSMG-C190
+12V POWER INPUT
A R1
2 1 +12V
+12V A
+12V
1K
GREEN
0.125W
R45
0.125W +12V
R47
1K
TIN
1%
0.1U
0.1U
0.1U
0.1U
100U
50V
50V
50V
50V
C18
C20
C22
C24
C26
35V
20%
R41 J1
TP3
R2
0
TIN
0.125W 1K 1
R42 1
0.125W
R46
1K 0.125W 2
TP0
2
1K
0.125W 3 3
1% 1K 4 4
0.125W
HSMG-C190
DS2
-12V
PIN
GREEN
0.1U
0.1U
0.1U
0.1U
100U
50V
50V
50V
50V
C19
C21
C23
C25
C27
35V
20%
-12V STRAIGHT
MATE_N_LOK
VCC
1
100U
-12V
35V
20%
C1
-12V
B P_GND B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
C J82
C
MOT_LR+ 7 7 1 1 COL_RES-
MOT_LR- 8 8 2 2 COL_RES+
MOT_UD+ 9 9 3 3 COL_FED_UD
MOT_UD- 10 10 4 4 COL_FED_LR
11 11 5 5 COL_LR
12 12 6 6 COL_UD
(MOT_COM)
SOCKET
STRAIGHT
DUAL_ROW
D D
REV 2 01July04
P_GND COLLIMATOR DRIVE INTERFACE
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Dec 21 14:50:07 2012 xray_board 3 of 6 5440559SCH 1 3 of 6
1
Approved Document - 5440559SCH_r1.pdf Page 4 of 7
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
0 1 1 2 2 1
2 3 3 4 4 3
4 5 5 6 6 5
DO-CPLD<15..0> 6 7 7 8 8 7 DO-CPLD<15..0>
0 9 9 10 10 1
A 2
4
11
13
11 12 12
14
3
5
A
13 14
6 15 15 16 16 7
8 17 17 18 18 9
10 19 19 20 20 11
12 21 21 22 22 13
COL-CPLD<7..0> 14 23 23 24 24 15 COL-CPLD<7..0>
0 25 25 26 26 1 R59
2 27 27 28 28 3 DA_LDAC_N
RESERVE 4 29 29 30 30 5
6 31 32 7 0
R43 NO JOINTING 31 32
CON_RES_LR+ DA_SYNC_N 33 34 DA_SCLK 0.125W
33 34 R52
DA_DIN 35 36 +0.05 CON_RES-
35 36
0 CON1_LR 37 38 CON1_UD
R44 37 38 RESERVE
COL_LR_AD 0.125W 39 40 0
39 40 NO JOINTING
+0.05 COL_FED_LR_AD 41 42 COL_FED_UD_AD 0.125W
41 42
0 +0.05
VCC
VCC
43 43 44 44
0.125W 45 46
45 46 R54
+0.05 47 48 CON_RES_UD+
47 48
49 49 50 50 RESERVE
0
NO JOINTING
0.125W
+0.05
PIN
STRAIGHT
RIBBON_CABLE_STANDARD R53
COL_UD_AD
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
0
0.125W
+0.05
R61 R63
See the GEHC Myworkshop System to determine the status of this document.
1K 1K
0.125W 0.125W
1% 1%
VCC
-12V
-12V
4
0.1U
VN
16V
10%
C31
10U
C30
VOUT
2
DIGITAL_CTRL_UD
VP
U14 AD822
U15
8
AD5322
+12V
0.1U
16V
10%
16V
10%
+12V
C39
C41
VR4
1U
AD586
2 VDD
8 NOISE_REDUCTION VOUT 6 4 VREFA VOUTA 5
+12V
+12V
16V
10%
DA_SCLK 8 +12V
C28
SCLK
1U
16V
10%
DA_DIN 9
C29
5V DIN
1U
8
AD822
VP
5
7 DIGITAL_CTRL_LR
6 VOUT
VN
4
0.1U
16V
10%
16V
10%
C38
C40
1U
-12V
-12V
R62 R64
1K 1K
0.125W 0.125W
D 1% 1%
D
REV 2 01July04
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Dec 21 14:41:19 2012 xray_board 4 of 6 5440559SCH 1 4 of 6
1
Approved Document - 5440559SCH_r1.pdf Page 5 of 7
2 3 4 5 6 7 8
Page 440 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
1 2 3 4 5 6 7 8
VCC
REC_DA<7..0> GND12 EN_N 4 EN 1 3 3 4 4 0
VCC
4 EN DI-CPLD<7..4> R3 3 5 5 6 6 2
DI-CPLD<3..0> 7 1 INN<3> 7 5 7 7 8 8 4
7 1 INN<3> 6 2 INP<3> O<3> 3 7 7 9 9 10 10 6
100
A 6
5
2
15
INP<3> O<3> 3 3 5
4
15
14
INN<2>
13 6
6 0
2
11
13
11 12 12
14
1
3
A
INN<2> INP<2> O<2> R4 13 14
4 14 INP<2> O<2> 13 2 3 7 INN<1> 5 4 15 15 16 16 5
3 7 INN<1> 2 6 INP<1> O<1> 5 5 6 17 17 18 18 7
2 6 5 1 1 9 4 100 8 19 20 9
INP<1> O<1> INN<0> 19 20
1 9 INN<0> 0 10 INP<0> O<0> 11 4 R5 10 21 21 22 22 11
0 10 INP<0> O<0> 11 0 3 12 23 23 24 24 13
14 25 25 26 26 15
VCC=VCC;GND=GND 2 100 16 27 27 28 28 17
VCC=VCC;GND=GND R6 18 29 29 30 30 19
1 20 31 31 32 32 21
U9 22 33 33 34 34 23
U4 DS26C31T 0 100 24 35 35 36 36 25
DS26C31T 26 37 37 38 38 27
28 39 39 40 40 29
EN_N 12 GND 30 41 41 42 42 31
VCC
EN_N 12 GND TRA_DB<7..0> EN 4 43 43 44 44
VCC
TRA_DA<7..0> EN 4 DO-CPLD<15..0> 45 45 46 46
DO-CPLD<15..0> 7 2 OUTP<3> I<3> 1 3 47 47 48 48
7 2 OUTP<3> I<3> 1 3 6 3 OUTN_N<3> 49 49 50 50
6 3 OUTN_N<3> 5 6 OUTP<2> I<2> 7 2 REC_DB<7..0>
5 6 OUTP<2> I<2> 7 2 4 5 OUTN_N<2>
4 5 OUTN_N<2> 3 10 OUTP<1> I<1> 9 1 PIN
3 10 OUTP<1> I<1> 9 1 2 11 OUTN_N<1> R7 STRAIGHT
2 11 OUTN_N<1> 1 14 OUTP<0> I<0> 15 0 7 DUAL_ROW_LATCHING
1 14 OUTP<0> I<0> 15 0 0 13 OUTN_N<0>
B 0 13 OUTN_N<0> 6 100 TRA_DA<31..0> B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
R8
VCC=VCC;GND=GND 5
VCC=VCC;GND=GND
U10 4 100
U5 DS26C31T R9 REC_DB<7..0>
DS26C31T 3
J342
EN_N 12 GND 2 100
VCC
EN_N 12 GND TRA_DB<15..8> EN 4 R10 1 1 2 2
VCC
TRA_DA<15..8> EN 4 1 1 3 3 4 4 0
15 2 OUTP<3> I<3> 1 7 3 5 5 6 6 2
See the GEHC Myworkshop System to determine the status of this document.
VCC
EN_N 12 GND TRA_DB<23..16> EN 4 28 39 39 40 40 29
VCC
TRA_DA<23..16> EN 4 30 41 41 42 42 31
23 2 OUTP<3> I<3> 1 11 43 43 44 44
23 2 OUTP<3> I<3> 1 11 22 3 OUTN_N<3> 0.1U 0.1U 0.1U 0.1U 0.1U 45 45 46 46
6 7 47 48
C10
22 3 OUTN_N<3> 21 OUTP<2> I<2> 10 47 48
C2
C4
C6
C8
21 6 OUTP<2> I<2> 7 10 20 5 OUTN_N<2> 50V 50V 50V 50V 50V 49 49 50 50
20 5 OUTN_N<2> 19 10 OUTP<1> I<1> 9 9
19 10 OUTP<1> I<1> 9 9 18 11 OUTN_N<1>
18 11 OUTN_N<1> 17 14 OUTP<0> I<0> 15 8 PIN
17 14 OUTP<0> I<0> 15 8 16 13 OUTN_N<0> STRAIGHT
16 13 OUTN_N<0> DUAL_ROW_LATCHING
VCC=VCC;GND=GND TRA_DB<31..0>
VCC=VCC;GND=GND U12 VCC
U7 DS26C31T
DS26C31T
12 GND TRA_DB<31..24> 4
C11
EN_N EN
C3
C5
C7
C9
VCC
REV 2 01July04
28 5 OUTN_N<2> 27 10 OUTP<1> I<1> 9 13
27 10 OUTP<1> I<1> 9 13 26 11 OUTN_N<1>
26 11 OUTN_N<1> 25 14 OUTP<0> I<0> 15 12
25 14 OUTP<0> I<0> 15 12 24 13 OUTN_N<0>
24 13 OUTN_N<0> GE Healthcare
Company Restricted
B Size
VCC=VCC;GND=GND
VCC=VCC;GND=GND
Block Path Block Sheet Dwg No Rev Sheet
Fri Dec 21 14:42:34 2012 xray_board 5 of 6 5440559SCH 1 5 of 6
1
Approved Document - 5440559SCH_r1.pdf Page 6 of 7
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
4
AR2
VCC
R48 +12V
LM324
A A
VCC
3
4
R68
AR3
VCC
1 R72
2K LM324
VCC
2 VOUT 3 R76
0.125W 10K
GND
1
1% 0.125W 2K 2 VOUT
0.125W
R80
1% 0.125W 10K
0.1U
0.1U
16V
10%
16V
10%
GND
C32
C34
11
1K
-12V 1% 0.125W
0.125W
R88
1%
0.1U
0.1U
16V
10%
16V
10%
-12V
C35
C37
11
1K
-12V
-12V
+12V
+12V
+12V +12V +12V
+12V +12V
4
AR2
VCC
+12V
4
R55
LM324 AR2
VCC
COL_FED_UD 5
4
R69
LM324 AR3
VCC
7 10
4
R73
2K LM324 AR3
VCC
6 VOUT 8 COL_FED_UD_AD COL_FED_LR 5 R77
0.125W 10K LM324
GND
9 VOUT 7 10
1% 0.125W 2K
0.1U
16V
10%
GND
6 8 COL_FED_LR_AD
C33
VOUT
1% 0.125W 10K
GND
9 VOUT
11
1% 0.125W
0.1U
16V
10%
GND
-12V
C36
11
-12V 1%
11
11
-12V
-12V
B -12V -12V -12V B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
R70 R71
-12V
R78 R79
10K 10K
0.125W 0.125W
1% 1% 10K 10K
0.125W 0.125W
1% 1%
See the GEHC Myworkshop System to determine the status of this document.
+12V
+12V +12V
+12V
4
AR5
VCC
R67
LM324
VCC
10
4
R82
AR4
VCC
8 R86
2K LM324
VCC
9 VOUT 12 R90
0.125W 10K
GND
14
1% 0.125W 2K 13 VOUT
0.125W
C C
R39
1% 0.125W 10K
0.1U
0.1U
16V
10%
16V
10%
GND
-12V
C42
C44
11
1K
1% 0.125W
0.125W
R40
1%
0.1U
0.1U
16V
10%
16V
10%
C45
C47
11
1K
-12V -12V
-12V
+12V +12V
AR5
VCC
+12V
4
R74
LM324 AR5
VCC
COL_UD 12 +12V
4
R83
LM324 AR4
VCC
14 3
4
R87
2K LM324 AR4
VCC
13 VOUT 1 COL_UD_AD COL_LR 3 R91
0.125W 10K LM324
GND
2 VOUT 1 5
1% 0.125W 2K
0.1U
16V
10%
GND
2 7 COL_LR_AD
C43
VOUT
1% 0.125W 10K
GND
6 VOUT
11
1% 0.125W
0.1U
16V
10%
GND
-12V -12V
C46
11
1%
11
-12V
11
-12V
-12V
-12V -12V
R84 R85
-12V
R92 R93
10K 10K
0.125W 0.125W
D 1% 1% 10K 10K
D
0.125W 0.125W
REV 2 01July04
1% 1%
GE Healthcare
Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
Fri Dec 21 14:50:39 2012 xray_board 6 of 6
1 5440559SCH 1 6 of 6
1
1
Approved Document - 5440559SCH_r1.pdf Page 7 of 7
2 3 4 5 6 7 8
Page 442 -
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
Section 2.0
Generator
Please refer to the Generator Schematics in CPI Service Manual.
Section 3.0
PDU
3.1 Digital System PDU Schematics
Section 4.0
Integrated Console
4.1 Digital System Console Schematics
5455343 5482782
FOOT S/W (5119258-
&20 7'63)6 ROHS):RIGHT
$ ,0*&219%'
5446734
,)%RDUG 5448182
)6
Table Horizontal Motion
$
J5 J2 5460013 5439299
5440284 6HH7DEOH 'RZQ12 Joystick(5450433)
6HHGLJLWDOER[363 a 9&& a &1 8S12
5V 3:$ Table TOP Left/Right
aa *1' aa 8S&
)50*5$%%' )%,7
5458295
5%,7$%5 /HIW12
Cable belong to Monitor - &1
'9, '9, 5455126 )21$%5 5LJK12 Collumn Up/Down
&$5' 6HH7DEOH - S 521$%5 5LJKW&
5461517 (0(5*$%5 5459790
5455121 5HG
/ ,'12 &1 Exposure Hand Switch
% ,PDJH0RQLWRU 5453651 1
,0*&219 6<1&6,* -
<
&1
*UHHQ
%
%'%1& *1' %1&
/ < S 5442517
1 )* ,0*&219%' ;5$<21 8'
)* 5454302 7(&+6327 8'
'LJLWDOLPDJH $%1250$/ 8'
6HH7DEOH
VXEV\VWHP &20 a 9 a /5 Collimator Blade Control
5436432 /5 Lever(5445992)
5443331
/5
&1 &RPS6
5451796:
&RPS4 Compressor Joystick(5461565)
& 36 &1 Include R1
- ; &RPS0 &
9 ; 7LOW6
TM1
(0B6723B&1
7LOW5
Table Tilt Joystick(5461565)
70 70 *1' &20 FOOT S/W (5119258-
Fuse holder X 2: 7LOW4 7LOW0
ROHS):LEFT
5438742 70 70 &1 9 &3,FRQVROH VLJQDOB*1' 1 1
2 2 7DEOH
* (0EXWWRQEDVH - - 0,&
5438693 *
5445937 -R\VWLFNEDVH 6LJQDO %1&
%1&
6KLHOG
'HVN-E
IRUGHEXJ 63.
72*(1(5$725 - CONSOLE SPK (5444084)
5442713 63.
GRRUEDVH
5456928 9$%& CN21
9$%& - 6HH7DEOH TO TABLE
MIS 5450388 MIS 5460585 Intercom J8
'HVN( 8QGHU Console-E2
5(9,6,216 $33529$/6 <<00'' 7,7/(
7'63EDVH 0$'(
3670,QWHJUDWHG&RQVROH6&+
5(9
+ &DELQHW(
5(9
0$'(%<
:X6KHQJ\RQJ
'$7(
(&512
-
'(6&5,37,21
,QLWLDOUHOHDVH &+(&.
),5670$'()25 3UHFLVLRQ7+81,6
+
$335
:X6KHQJ\RQJ -81
7DEOH5HYWRPRGLI\OLVW
*(+8$/810(',&$/ 6+7&21721
:X6KHQJ\RQJ '(& 7DEOH5HYWRPRGLI\OLVW
27+(5
6&+
6<67(06
7$%/( 7$%/( 7$%/(
CCU REALTIME CONTROL CABLE TDSP CN333 CONTROL CABLE GENERATOR ROOM I/F CABLE
$ $
CONSOLE CONSOLE TDSP CONSOLE TDSP SIGNAL CONSOLE GENERATO
I/F J7 PCU J7 SIGNAL NAME I/F J15 CN333 SIGNAL NAME I/F J15 CN333 NAME I/F J17 R SIGNAL NAME
MEM_CMD_2 VCC ABNORMAL TB6-7 REMOTE_PREP_P
reserved VCC reseved TB6-8 REMOTE_PREP_N
reserved VCC reseved TB6-5 REMOTE_FLUORO_P
% MEM_CMD_1 VCC reseved TB6-6 REMOTE_FLUORO_N %
GND VCC reseved TB6-9 REMOTE_EXP_P
SHAD_CMD_1 VCC reseved TB6-10 REMOTE_EXP_N
MEM_CMD_3 GND reseved TB5-11 MULTISPOT_P
BLK_CMD GND reseved TB5-12 MULTISPOT_N
& RF_CMD_1 GND reseved TB6-2 XRAY_ON_P &
GND GND reseved TB6-1 XRAY_ON_N
SHAD_CMD_0 GND reseved TB5-2 SPARE_INPUT1_P
MEM_CMD_4 GND reseved TB5-3 SPARE_INPUT1_N
RF_CMD_2 F-BIT reseved TB5-5 SPARE_INPUT2_P
RF_CMD_0 R-BIT/ABR1 GND TB5-6 SPARE_INPUT2_N
' GND
'
F-ON/ABR2 GND TB5-8 SPARE_INPUT3_P
EE_CMD_0 R-ON/ABR3 GND TB5-9 SPARE_INPUT3_N
VI_CMD EMGCY/ABR4 GND TB6-12 SPARE_INPUT4_P
GAMMA_CMD_1 ID NO.+ GND TB6-11 SPARE_INPUT4_N
LIM_CMD Y5 GND
( GND Y6 12V (
reserved 12V 12V 7$%/(
MEM_CMD_0 12V 12V I.I. POWER AND CONTROL CABLE
MEM_CMD_5 TECH_SPOT 12V
CONSOL
reserved reseved 12V E I/F J5 I.I. SIGNAL NAME
GND XRAY_ON 12V
) GND )
MEM_CMD_6
GND
MODE_CMD_1 7$%/( GND
MODE_CMD_2 CPI CONSOLE RS232 COM CABLE II_CTRL<1>
MODE_CMD_3 CONSOLE
CONSOLE DATALIN GND
GND
I/F J2 SIGNAL NAME GND
* GAMMA_CMD_2 K *
RS_TXD II_CTRL<2>
MODE_CMD_0
RS_RXD II_CTRL<0>
TXT_CMD
GND 24V
HI_CMD
GND 5(9,6,216 7,7/(
$33529$/6 <<00'' 5(9
-81
$335
),5670$'()25
7DEOH5HYWRPRGLI\OLVW
*(+8$/810(',&$/ 6+7&21721
:X6KHQJ\RQJ '(& 7DEOH5HYWRPRGLI\OLVW
27+(5
6&+
6<67(06
7$%/(
7$%/(
7$%/( Console IF Communication Cable
$ ENCODER SIGNAL CABLE SIGNAL $
DSA LVDS CONVERTER CABLE TDSP J3 I/F J6
CONSOLE NAME
IMG. CONV.
I/F J8/J10 ENCODER SIGNAL NAME PCU J5 BOARD SIGNAL NAME TXD
GND VID0+ RXD
CHANNEL B VID0- GND
% VCC VID1+ 7$%/( %
CHANNEL A DIGITAL INTERFACE CABLE
VID1- CONSOLE GENERAT
SHILED VID2+ I/F J4 OR J2 SIGNAL NAME
VID2- - DIGITAL FLUORO ON_P
- DIGIAL RAD PREP_P
7$%/( VID3+ - DIGITAL RAD READY_P
VID3- - DIGITAL MODE SEL_P
& 1750 CARD CONTROL CABLE &
VID4+ - DIGITAL II MODE1_P
CONSOLE 1750 - DIGITAL II MODE2_P
VID4-
I/F J3 CARD SIGNAL NAME - DIGITAL RAD EXPOSURE_P
VID5+ -
RAD_STATUS DIGITAL_II_MODE3_P
VID5- DIGITAL PULSE FLUORO SEL_P
FLUORO_STATUS
VID6+ - DIGITAL PULSE FLUORO ON_P
SINGLE_SPOT -
' VID6-
DIGITAL XRAY ON_P '
GATE_TRIGGER - DIGITAL PULSE FLUORO SYNC_P
VID7+ N/A
GATE_SELECT
VID7- - DIGITAL FLUORO ON_N
DSA_SELECT - DIGIAL RAD PREP_N
VID8+
PATH_SELECT - DIGITAL RAD READY_N
VID8- -
REPLAY_SELECT DIGITAL MODE SEL_N
( VID9+ - DIGITAL II MODE1_N (
GND
VID9- - DIGITAL II MODE2_N
GND - DIGITAL RAD EXPOSURE_N
VID10+
SINGLE_FRM_FORWARD - DIGITAL_II_MODE3_N
VID10- DIGITAL PULSE FLUORO SEL_N
SINGLE_FRM_BACKWARD
VID11+ - DIGITAL PULSE FLUORO ON_N
WW_INCREASE - DIGITAL XRAY ON_N
VID11-
) WW_DECREASE - DIGITAL PULSE FLUORO SYNC_N )
FRAME_VALID+
WL_INCREASE 7$%/(
FRAME_VALID- ENCODER SIGNAL CABLE
WL_DECREASE
DATA_VALID+
reserved CONSOLE
DATA_VALID- I/F J8/J10 ENCODER SIGNAL NAME
reserved
LINE_VALID+ GND
GND
* LINE_VALID- *
GND CHANNEL B
VCC
CHANNEL A
SHILED
5(9,6,216 $33529$/6 <<00'' 7,7/(
5(9
0$'(
3670,QWHJUDWHG&RQVROH6&+
+ 5(9
0$'(%<
:X6KHQJ\RQJ
'$7(
(&512
-
'(6&5,37,21
Initial release &+(&.
),5670$'()25 3UHFLVLRQ7+81,6
+
$335
:X6KHQJ\RQJ -81
7DEOH5HYWRPRGLI\OLVW
*(+8$/810(',&$/ 6+7&21721
:X6KHQJ\RQJ '(& 7DEOH5HYWRPRGLI\OLVW
27+(5
6&+
6<67(06
Revision NOTE:
1 2 3 4 5 6 7 8
A A
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
2299773GSP.
4. ELECTRONIC SIGNATURES FOR BOTH THE
Thisboard
This board isPWA2408827,Only
reused reuse PWA2408827,Only
some componentssome
updated.components updated. SCHEMATIC REVIEWER(S) AND APPROVER(S)
CAN BE FOUND WITHIN E-PDM.
REVISION 1:Update U7, U8, U10, U12, U22, U25, U31 from TPL281-4 to TCMT4001(GEPN:2364058-4)
TCMT4001 because of EOL. because of EOL.
5. UNLESS OTHERWISE SPECIFIED:
B REVISION 2:
2: Update
Update U1-U6,U9,U14-17,U21,U24,U26,U29,U30,U32
U1-U6,U9,U14-17,U21,U24,U26,U29,U30,U32 from
from 74VHC_AHC14 to SN74ACT14PW(GEPN:5483237), CAPACITORS ARE IN FARADS. B
REVISION to SN74ACT14PW(GEPN:5483237) because of current drive ability.
RESISTORS ARE IN OHMS.
because of current drive ability. INDUCTORS ARE IN HENRIES
C C
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-SEP-2012
10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
console_if 1 of 2 54366486&+ 2 1 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
GEN_DIG_IF
A A
DIG_FLUORO_ON 0
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
DIG_II_MODE1 1
GEN_DIG_OUTPUT<1..0> 0 PULSE_FLUORO_SYNC_SIG
DIG_II_MODE2
DIG_II_MODE3
2
3
FPGA
1 RAD_EXP_CMD
DIG_MODE_SEL 4
TEMP_ALARM
DIG_PULSE_FLUORO_ON 5
SFD_INPUT<7..0> OPERATOR_IF
DIG_PULSE_FLUORO_SEL 6
ENCODER_CH<3..0> DIGITAL_INPUT4<3..0>
DIG_RAD_PREP 7
DIGITAL_OUTPUT2<1..0>
GEN_INPUT<6..0>
DIGITAL_OUTPUT3<4..0> GEN_ROOM_CMD<4..0>
DIGITAL_OUTPUT4<26..0> CCU_RT_CMD<26..0>
CPI_CONSOLE_RS1_RXD
CPI_CONSOLE_RS1_TXD
CCU_IF CPI_CONSOLE_RS2_RXD
CPI_CONSOLE_RS2_TXD
DIGITAL_OUTPUT5<2..0> II_MODE_SEL<2..0>
C II_MODE_SEL<2..0> II_MODE_SEL<2..0> C
PCI_CARD_IF<15..0> CPI_CONSOLE_IF
CCU_RT_CMD<26..0> CCU_RT_CMD<26..0> II_EN
II_EN
CCU_RS232<3..0> CPI_RS1_RXD
CAMERA_READY CPI_RS1_TXD
CPI_RS2_RXD
DSA_INF
CPI_RS2_TXD
NOTE: CCU ALSO NAMED AS PCU
PCI_CARD_IF<15..0>
NOTE: THIS MODULE NOT USED IN STORM PROGRAM
PC_RS232<1..0>
POWER
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-SEP-2012
10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
console_if 2 of 2 54366486&+ 2 2 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
A A
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
VCC
R1
475 U7
0.125W
1% TCMT4100
U2 U2 7 10 DIG_RAD_EXP_P
SN74ACT14 SN74ACT14 CONN25_SUBD_PLUG_2GND_STR
D2
BAS116 1 13
RAD_EXP_CMD 3 A B 4 9 A B 8 8 9 DIG_RAD_EXP_N
IN
See the GEHC Myworkshop System to determine the status of this document.
VCC DS1
HSMG-C190
R89
2 1
B 475
B
GREEN J4
0.125W
1%
DIG_FLUORO_ON_P 1 1
DIG_RAD_PREP_P 2 2 14 14 DIG_FLUORO_ON_N
VCC DIG_RAD_READY_P 3 3 15 15 DIG_RAD_PREP_N
DIG_MODE_SEL_P 4 4 16 16 DIG_RAD_READY_N
DIG_II_MODE1_P 5 5 17 17 DIG_MODE_SEL_N
R2 U7 DIG_II_MODE2_P 6 6 18 18 DIG_II_MODE1_N
475 TCMT4100 DIG_RAD_EXP_P 7 7 19 19 DIG_II_MODE2_N
0.125W DIG_II_MODE3_P 8 8 20 20 DIG_RAD_EXP_N
1% DIG_PULSE_FLUORO_SEL_P 9 9 21 21 DIG_II_MODE3_N
U2 U6 5 12 DIG_PULSE_FLUORO_SYNC_P DIG_PULSE_FLUORO_ON_P 10 10 22 22 DIG_PULSE_FLUORO_SEL_N
SN74ACT14 DIG_XRAY_ON_P 11 11 23 23 DIG_PULSE_FLUORO_ON_N
SN74ACT14 DIG_PULSE_FLUORO_SYNC_P 12 24 DIG_XRAY_ON_N
D3 12 24
BAS116 13 13 25 25 DIG_PULSE_FLUORO_SYNC_N
PULSE_FLUORO_SYNC_SIG 5 A B 6 1 A B 2 6 11 DIG_PULSE_FLUORO_SYNC_N
IN
G1 G1
75V G2 G2
VCC=VCC;GND=GND VCC=VCC;GND=GND
VCC DS2
PIN
C HSMG-C190
STRAIGHT
C
R90 STD_DENSITY
2 1
475
GREEN
0.125W
1%
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
gen_dig_if 1 of 2 54366486&+ 2 3 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
VCC VCC DS15
U8
C4 HSMG-C190
TCMT4100
R104
VCC DS3 2 1
VCC HSMG-C190 DIG_II_MODE2_P 1 16 0.1U
U7 U9
C9 50V 475
TCMT4100 R91 SN74ACT14 GREEN
2 1 10% 0.125W
D9
1%
BAS116
DIG_FLUORO_ON_P 3 14 0.1U 475 2 15 1 2 DIG_II_MODE2
U6 GREEN A B OUT
50V 0.125W
10% SN74ACT14 1%
D4 75V R30 R35 R40 R7
A BAS116 6.81K 6.81K 6.81K 4.99K VCC=VCC;GND=GND A
4 13 3 A B 4 DIG_FLUORO_ON 0.125W 0.125W 0.125W 0.125W
OUT 1% 1% 1% 1%
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
C DIG_MODE_SEL_P 5 12 0.1U U6
475
GREEN DIG_PULSE_FLUORO_ON_P 3 14 0.1U U9
475
GREEN
C
50V 0.125W 50V 0.125W
10% SN74ACT14 1% 10% SN74ACT14 1%
D7 D12
BAS116 BAS116
6 11 11 A B 10 DIG_MODE_SEL 4 13 9 A B 8 DIG_PULSE_FLUORO_ON
OUT OUT
75V R13 R18 R23 R5 75V R33 R38 R43 R26
6.81K 6.81K 6.81K 4.99K VCC=VCC;GND=GND 6.81K 6.81K 6.81K 4.99K VCC=VCC;GND=GND
0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W
1% 1% 1% 1% 1% 1% 1% 1%
DIG_MODE_SEL_N DIG_PULSE_FLUORO_ON_N
VCC DS19
VCC DS7 VCC HSMG-C190
U10
VCC HSMG-C190 C8
U8 TCMT4100 R116
C3 R103 2 1
TCMT4100 2 1
DIG_XRAY_ON_P 1 16 0.1U 475
U9 GREEN
DIG_II_MODE1_P 3 14 0.1U 475 50V 0.125W
U6 GREEN SN74ACT14
50V 0.125W 10% 1%
SN74ACT14 D13
10% 1%
D8 BAS116
BAS116 2 15 11 A B 10 DIG_XRAY_ON
OUT
4 13 13 A B 12 DIG_II_MODE1
OUT
75V R34 R39 R44 R27
75V R14 R19 R24 R6 6.81K 6.81K 6.81K 4.99K VCC=VCC;GND=GND
6.81K 6.81K 6.81K 4.99K VCC=VCC;GND=GND 0.125W 0.125W 0.125W 0.125W
D 0.125W
1%
0.125W
1%
0.125W
1%
0.125W
1%
1% 1% 1% 1% D
DIG_XRAY_ON_N
DIG_II_MODE1_N
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
gen_dig_if 2 of 2 5436648SCH 2 4 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
VCC
D14 K5
U26 U29 BAS116 TQ2SA-5V
SN74ACT14 SN74ACT14
A 75V 1 COILP
DS20
A
GEN_OUTPUT<4..0> 0 3 A B 4 1 A B 2 10 COILN
IN HSMG-C190 CONN25_SUBD_REC_2GND
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
VCC
J17
D15 K6
U26 U29 BAS116 TQ2SA-5V
SN74ACT14 REMOTE_PREP_P 1 1
SN74ACT14
REMOTE_FLUORO_P 2 2 14 14 REMOTE_PREP_N
75V 1 COILP REMOTE_EXP_P 3 3 15 15 REMOTE_FLUORO_N
1 5 6 3 4 10 DS21 REMOTE_SPARE1_P 4 16 REMOTE_EXP_N
A B A B COILN 4 16
See the GEHC Myworkshop System to determine the status of this document.
GREEN
VCC
D17 K8
U26 U29 BAS116 TQ2SA-5V
C SN74ACT14 SN74ACT14 C
75V 1 COILP
3 13 12 9 8 10 DS23
A B A B COILN
HSMG-C190
REMOTE_SPARE1_P 3 COM CLOSED 2
VCC=VCC;GND=GND VCC=VCC;GND=GND OPEN 4 2 1 REMOTE_SPARE1_N
GREEN
VCC
D18 K9
U26 U29 BAS116 TQ2SA-5V
SN74ACT14 SN74ACT14
75V 1 COILP
4 11 10 11 10 10 DS24
A B A B COILN
HSMG-C190
REMOTE_SPARE2_P 3 COM CLOSED 2
VCC=VCC;GND=GND VCC=VCC;GND=GND OPEN 4 2 1 REMOTE_SPARE2_N
GREEN
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
gen_room_if 1 of 2 5436648SCH 2 5 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
75V R50 R54 R58 R216 75V R220 R223 R226 R229
6.81K 6.81K 6.81K 4.99K VCC=VCC;GND=GND 6.81K 6.81K 6.81K 4.99K VCC=VCC;GND=GND
0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W
1% 1% 1% 1% 1% 1% 1% 1%
GEN_INPUT1_N GEN_INPUT5_N
TCMT4100 VCC DS26 VCC DS30
HSMG-C190 HSMG-C190
R118 R123
U12 2 1 U31 2 1
VCC
TCMT4100 475 TCMT4100 475
VCC GREEN GREEN
C22 0.125W C87 0.125W
See the GEHC Myworkshop System to determine the status of this document.
GEN_INPUT2_P 5 12 1% GEN_INPUT6_P 5 12 1%
U30 U30
U30
0.1U
SN74ACT14 0.1U SN74ACT14
D20 D29
BAS116 50V BAS116 50V
6 11 10% 1 2 1 6 11 10% 11 10 5
A B A B
75V R51 R55 R59 R217 75V R221 R224 R227 R230
B 6.81K 6.81K 6.81K 4.99K VCC=VCC;GND=GND 6.81K 6.81K 6.81K 4.99K VCC=VCC;GND=GND B
0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W
1% 1% 1% 1% 1% 1% 1% 1%
GEN_INPUT2_N GEN_INPUT6_N
75V R52 R56 R60 R218 75V R222 R225 R228 R231
6.81K 6.81K 6.81K 4.99K VCC=VCC;GND=GND 6.81K 6.81K 6.81K 4.99K VCC=VCC;GND=GND
0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W
1% 1% 1% 1% 1% 1% 1% 1%
C C
GEN_INPUT3_N GEN_INPUT7_N
VCC DS28
HSMG-C190
R120
U12 2 1
GEN_INPUT4_N
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
gen_room_if 2 of 2 5436648SCH 2 6 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
A VCC CONN9_SUBD_PLU_2GND A
D1 K1
U2 U2 BAS116 TQ2SA-5V CCU_RS232<3..0>
OUT
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
SN74ACT14 SN74ACT14 1 5
J6
75V 1 COILP
II_MODE_SEL<2..0> 0 11 A B 10 13 A B 12 10 COILN GND GND
IN 6 9
CH21 1 1
24V 3 COM CLOSED 2 CH1 0 CH23 2 2 6 6
VCC=VCC;GND=GND VCC=VCC;GND=GND OPEN 4 0 1 3 3 7 7 3
COMPONENT1 2 4 8
CH22 4 8
COMPONENT2 5 9
5 9
G1 G1
G2 G2
A
RS_GND
PIN
STRAIGHT
See the GEHC Myworkshop System to determine the status of this document.
VCC STD_DENSITY
D25 K2
U24 U24 BAS116 TQ2SA-5V
SN74ACT14 SN74ACT14
75V 1 COILP
1 1 A B 2 5 A B 6 10 COILN
B B
24V 3 COM CLOSED 2 CH56
VCC=VCC;GND=GND VCC=VCC;GND=GND OPEN 4 1
VCC
D26 K3
U24 U24 BAS116 TQ2SA-5V
SN74ACT14 SN74ACT14
75V 1 COILP
2 3 A B 4 9 A B 8 10 COILN
C C
VCC
D31 K10
U32 U32 BAS116 TQ2SA-5V
SN74ACT14 SN74ACT14
75V 1 COILP
II_EN 1 A B 2 3 A B 4 10 COILN
IN
24V 3 COM CLOSED 2
VCC=VCC;GND=GND VCC=VCC;GND=GND OPEN 4
J5
1 1
2 2 9 9
3 3 10 10
4 4 11 11
5 5 12 12
1 6 6 13 13 2 II_CTRL<2..0>
7 7 14 14 0
8 8 15 15
D D
G1 G1
G2 G2
REV 2 1July04
SOCKET
STRAIGHT Made By Date Title
STD_DENSITY GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
ccu_if 1 of 2 5436648SCH 2 7 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
CCU RT INTERFACE
U5 THE SHORTS ARE FOR PROBE USAGE
A SN74ACT14 A
CCU_RT_CMD<26..0> CCU_RT_CMD_OUT<26..0>
IN CONN37_SUBD_REC_2GND
CH24
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
U14 CCU_RT_CMD_OUT<26..0>
SN74ACT14
CH26 J7
6 1 A<5> B<5> 2 CH35 6
See the GEHC Myworkshop System to determine the status of this document.
VCC=VCC;GND=GND
U17
SN74ACT14
CH32
24 1 A B 2 24
VCC=VCC;GND=GND
U17
SN74ACT14
CH41
25 3 A B 4 25
VCC=VCC;GND=GND
U17
SN74ACT14
D D
CH50
26 5 A B 6 26
REV 2 1July04
VCC=VCC;GND=GND
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
ccu_if 2 of 2 5436648SCH 2 8 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
VCC PS1
DCR010505U RS_VCC VR1 75V
VCC LT1117-3V3
1 VS1 VOUT 14
2 VS2 R109 3 VIN VOUT1 2
ERROR_N 17 VOUT2 4
C53 28 SYNCIN VREC 12
2.2U 26 16 10K C47 C48 1 C49
0VIN1 ENABLE R108 ADJ_GND
35V 27 13 0.125W 10U 100U
0VIN2 0VOUT 0.1U
10% 1% 35V 50V 16V
10K 20% 10% 20%
3.3V
0.125W
5V
1%
R107
3 VIN VOUT 1
PIN PIN
STRAIGHT RIGHT_ANGLE
POWER_HEADER TERMINAL_BLOCK_HEADER
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
1 of 3 5436648SCH 2 9 of 19
power
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
VOLTAGE DIAGNOSTIC
TP6
TP9
TIN
24V TIN
R111
A 4.99K
DS32
3V3 R127 A
0.125W 4.99K
1% HSMY-C190 0.125W DS36
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
1% HSMY-C190
R125
2 1 R131
2 1
4.99K
YELLOW
0.125W 200
YELLOW
1% 0.125W TP12 TP13 TP14
1%
R130
TIN TIN TIN
4.99K
0.125W
1%
R132
4.99K
See the GEHC Myworkshop System to determine the status of this document.
0.125W
1% TP10
R133
TP5 TIN
4.99K 2V5
TIN R128
12V 0.125W 4.99K
1% DS37
B R110 0.125W
1% HSMY-C190
B
4.99K
0.125W DS34
R121
1% HSMY-C190 2 1
R134 R232
2 1 200
YELLOW
0.125W
475 475 1%
YELLOW
0.125W 0.125W
R236
1% 1%
R135 R233
200
0.125W
475 475 1%
0.125W 0.125W TP8
1% 1%
TIN
R126
4.99K 12NV
DS35 0.125W
HSMY-C190 1%
R136 R234
C 2 1 C
475 475
YELLOW
0.125W 0.125W
1% 1%
R137 R235 TP11
VCC 200
R112 YELLOW
4.99K 0.125W A
0.125W DS33 1% RS_GND
1% HSMY-C190
R138
2 1
200
YELLOW
0.125W
1%
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
2 of 3 5436648SCH 2 10 of 19
power
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
VCC
MH1
C23 C26 C29 C32 C35 C38 C41 C44 C62 C65 C68 C71 MH5_00_M4WASHER
0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U
1
50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V
10% 10% 10% 10% 10% 10% 10 % 10% 10% 10% 10% 10% MH2
MH5_00_M4WASHER
1
MH3
MH5_00_M4WASHER
1
See the GEHC Myworkshop System to determine the status of this document.
VCC
MH4
MH5_00_M4WASHER
1
C78 C79 C80 C81 C82 C83 C84 C85 C86 MH5
0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U MH5_00_M4WASHER
B 50V 50V 50V 50V 50V 50V 50V 50V 50V B
1
10% 10% 10% 10% 10% 10% 10% 10% 10%
MH6
MH5_00_M4WASHER
1
3V3
C24 C27 C30 C33 C36 C39 C42 C45 C63 C66 C69 C72 C74 C76 C77
0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U
50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V
10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10%
C C
2V5
C25 C28 C31 C34 C37 C40 C43 C46 C64 C67 C70 C73 C75
0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U
50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V
10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10%
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
3 of 3 5436648SCH 2 11 of 19
power
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
14 25
GND GND
9 6
PCI_CARD_CTRL<15..0>
J3
COMPONENT1
COMPONENT2
0 1 1
1 2 2 14 14 8 J2
2 3 3 15 15 9
3 4 4 16 16 10
4 5 5 17 17 11 CH18 1 1 6 6
5 6 6 18 18 12 PC_RS232<1..0> 0 CH20 2 2 7 7
IN
6 7 7 19 19 13 1 3 3 8 8
7 8 8 20 20 14 CH19 4 4 9 9
9 9 21 21 15 5 5
See the GEHC Myworkshop System to determine the status of this document.
10 10 22 22 G1 G1
11 11 23 23 G2 G2
12 24 A
12 24
13 13 25 25 RS_GND
SOCKET
G1 G1 STRAIGHT
G2 G2 STD_DENSITY_NONMAGNETIC
B B
PIN
STRAIGHT
STD_DENSITY
U1 Q2
ULN2803
SN74ACT14
PCI_CARD_IF<15..0> CH2
IN
0 1 A<5> B<5> 2 1 I1 O1 18 CH6 0
1 3 A<4> B<4> 4 2 I2 O2 17 CH10 1
2 5 A<3> B<3> 6 3 I3 O3 16 CH14 2
3 9 A<2> B<2> 8 4 I4 O4 15 CH3 3
4 11 A<1> B<1> 10 5 I5 O5 14 CH7 4
5 13 A<0> B<0> 12 6 I6 O6 13 CH11 5
7 I7 O7 12 CH15 6 24V
8 I8 O8 11 7
VCC=VCC;GND=GND 10
C U3 COMMON
C
GND 9
SN74ACT14
6 1 A<5> B<5> 2
7 3 A<4> B<4> 4
8 5 A<3> B<3> 6
9 9 A<2> B<2> 8
10 11 A<1> B<1> 10
11 13 A<0> B<0> 12 Q1
ULN2803
VCC=VCC;GND=GND CH4
U4 1 I1 O1 18 CH8 8
2 I2 O2 17 CH12 9
SN74ACT14
3 I3 O3 16 CH16 10
4 I4 O4 15 CH5 11
12 1 A<5> B<5> 2 5 I5 O5 14 CH9 12 24V
13 3 A<4> B<4> 4 6 I6 O6 13 CH13 13
14 5 A<3> B<3> 6 7 I7 O7 12 CH17 14
15 9 A<2> B<2> 8 8 I8 O8 11 15
11 A<1> B<1> 10 10
13 A<0> B<0> 12 COMMON
GND 9
VCC=VCC;GND=GND
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
dsa_inf 1 of 1 5436648SCH 2 12 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
A A
CONN2X3_2X1
1 5
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
2 6
COMPONENT1
COMPONENT2
J1
CPI_RS2_RXD 2 2 1 1 CPI_RS1_RXD
OUT OUT
CPI_RS2_TXD 4 4 3 3 CPI_RS1_TXD
OUT OUT
6 6 5 5
See the GEHC Myworkshop System to determine the status of this document.
PIN
A A
RIGHT_ANGLE
RS_GND WIRE_TO_BOARD RS_GND
B B
C C
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
cpi_console_if 1 of 1 5436648SCH 2 13 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
ENCODER1_CHA 4 4
OUT
5 5 1 1 2 2
13 A B 12 1 I1 O1 18 TECH_SPOT 3 3 4 4
2 I2 O2 17 XRAY_ON_TO_SFD 5 5 6 6
PIN 3 I3 O3 16 ABNORMAL 7 7 8 8
STRAIGHT VCC=VCC;GND=GND 4 I4 O4 15 9 9 10 10
WIRE_TO_BOARD U17 5 I5 O5 14 11 11 12 12
6 I6 O6 13 0 F_BIT 13 13 14 14 R_BIT 4
SFD_24V_CMD<2..0> 0 SN74ACT14 7 12 24V 1 F_ON 15 16 R_ON 5
IN I7 O7 15 16
1 8 I8 O8 11 12V 2 EMERGENCY 17 17 18 18 IDNO 6 12V
2 11 A B 10 10 3 Y5 19 19 20 20 Y6 7
FOR CONTRAST ADJ. COMMON
9 TECH_SPOT
21
23
21 22 22
24
GND 23 24
VCC=VCC;GND=GND XRAY_ON_TO_SFD 25 25 26 26 ABNORMAL
U17 27 27 28 28
29 29 30 30
SN74ACT14
See the GEHC Myworkshop System to determine the status of this document.
J10 31 31 32 32
VCC 33 33 34 34
9 A B 8 35 35 36 36
1 1 37 37 38 38
ENCODER2_CHB 2 2 39 39 40 40
OUT
3 3 VCC=VCC;GND=GND 41 41 42 42
ENCODER2_CHA 4 4 43 43 44 44
OUT
B 5 5 12V 45 45 46 46 12V B
47 47 48 48
49 49 50 50
PIN
STRAIGHT
WIRE_TO_BOARD PIN
STRAIGHT
DUAL_ROW_LATCHING
TEMP SWITCH
Reserve, not welding VCC
U28
TO INJECTION
MAX6502 R105
VCC 100K
0.125W
4 VCC 1% VCC
D27
3 HYST TOVER 5 TEMP_ALARM BAS116 K4
OUT
U24 U2 TQ2SA-5V
GND<1-0>
C SN74ACT14 SN74ACT14
75V
C
1 COILP
INJECT_CMD 13 A B 12 1 A B 2 10 COILN J11
IN
3 COM CLOSED 2
OVER HEAT ALARM VCC=VCC;GND=GND VCC=VCC;GND=GND OPEN 4 1
2
1
2
U24 TO BEEPER
J16
SN74ACT14 PIN
RIGHT_ANGLE
OVERHEAT_ALARM11 A B 10 1 1 VCC WIRE_TO_BOARD
IN
2 2
VCC=VCC;GND=GND
PIN R238 R239 R240 R241 R242 R243
STRAIGHT 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K
WIRE_TO_BOARD 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W
1% 1% 1% 1% 1% 1%
0
6
1
SFD_INPUT<7..0>
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
operator_if 1 of 1 5436648SCH 2 14 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
CONN2X5
2 10
3V3
U18
3V3 3V3 3V3 2V5 3V3 EP1K100_208-3
3V3 1 9
R63 U13
COMPONENT1 3V3 1K EPC2LC20
COMPONENT2 0.125W R66 R67 R69 VCCIO<13-0> CS_N 208 RS3_TXD
1% 1K 1K 1K VCCINT<10-0> RS_N 204 RS3_RXD
R28 R29 R45 JTAG 18 VPP 0.125W 0.125W 0.125W 77 VCC_CKLK WS_N 206 RS4_TXD
A 1K 1K 1K 3V3 20 VCC 1% 1% 1% CEO_N 3 A
0.125W 0.125W 0.125W J12 CASC_N 12 154 CE_N STATUS_N 52 STATUS_N
1% 1% 1% CONF_DONE 9 CS_N INIT_CONF_N 13 105 CONFIG_N CONFIG_CMD<3..0> VCC
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
TDO 1 CS 207 0
TCK 1 1 2 2 C12 TDI 11 TDI DATA 2 TCK 1 TCK TDO 4 TDO
TDO 3 3 4 4 0.1U TMS 19 TMS OE 8 STATUS_N TMS 50 TMS CLKUSR 10 RS4_RXD R248
TMS 5 5 6 6 50V TCK 3 TCK DCLK 4 51 TRST RDYNBUSY 16 1 4.99K
7 7 8 8 10% 153 TDI INIT_DONE 19 2 0.125W
TDI 9 9 10 10 R64 14 VPPSEL 156 DATA0 CONF_DONE 2 CONF_DONE 1%
5 VCCSEL GND 10 155 DCLK DEV_CLRN 180 3
R47 R68 108 MSEL0 DEV_OE 186 II_EN
1K OUT
1K PIN 107 MSEL1
0.125W 0.125W CLK_16MHZ 79 DIAGNOSTIC_CMD<6..0>
STRAIGHT GCLK1
1% 1% 1K 183 157 0
DUAL_ROW_POLARIZED GCLK2 DATA1
0.125W 158 1
DATA2
1% BOARD_RESET 78 159 2
IN_78 DATA3
HUNDRIC_SYNC_IN 80 IN_80 DATA4 161 3
TEMP_ALARM 182 IN_182 DATA5 162 4
IN
184 IN_184 DATA6 164 5
See the GEHC Myworkshop System to determine the status of this document.
DATA7 166 6
GND<19-0>
GND_CKLK 81
SYM 1 OF 2
TP1
B B
TIN 3V3
DS8
HSMG-C190
U11 R49
S1
EP11SD1ABE VCC
MAX701 4.99K
0.125W
HUNDRIC SYNC IN 2 1
R70
0
1% TP3
8 6 200
VCC RESET_N CONN_BNC_3GND GREEN
5 BOARD_RESET 0.125W
RESET TIN
1 3 1 DS9 1%
1 3 MR
4 HSMG-C190
GND R65
G1 G1 4.99K 1 G1 R71
G2 G2 TP2 0.125W G3 G2 2 1 1
5V 1% J13
200
TIN COMPONENT1 GREEN
0.125W
COMPONENT2
HUNDRIC_SYNC_IN 1 DS10 1%
R62
4.99K HSMG-C190
G1
SG-8002CA-16.000
SG-8002CA-6.144MHz 0.125W GND G1 R72
VCC 1% CGND1 G2 2 1 2
R48 CGND2 G3
4 3 CLK_16MHZ 200
VCC VOUT GREEN
0.125W
R46
C C11 1 2 10
SOCKET
DS11 1% C
ENABLE GND 0.125W HSMG-C190
0.1U STRAIGHT
50V 4.99K 1%
BNC R73
10% 0.125W 2 1 3
1%
VCC 200
GREEN
0.125W
DS12 1%
HSMG-C190
R244 R245 R246 R247 R74
4.99K 4.99K 4.99K 4.99K 2 1 4
0.125W 0.125W 0.125W 0.125W S2
1% 1% 1% 1% 200
219-04MST GREEN
0.125W
CONFIG_CMD<3..0> DS13 1%
0 1 I1 O1 8 HSMG-C190
R75
1 2 I2 O2 7 2 1 5
2 3 I3 O3 6 200
GREEN
0.125W
3 4 I4 O4 5 DS14 1%
HSMG-C190
R76
2 1 6
200
D GREEN
0.125W
D
1%
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
fpga 1 of 5 5436648SCH 2 15 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
A A
PCI_CARD_IF<15..0>
OUT
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
3
0
2
4
5
6
8
9
7
SFD_24V_CMD<2..0>
10
12
13
14
15
11
OUT
0
2
SFD_INPUT<7..0>
1
IN
3
0
2
4
5
6
7
1
0 DIGITAL_OUTPUT1<1..0>
OUT
1
0 DIGITAL_OUTPUT2<1..0>
OUT
1
100
102
103
104
112
113
114
115
116
119
120
122
125
126
127
128
132
133
134
135
136
139
140
142
143
144
101
111
121
131
141
IO_100
IO_101
IO_102
IO_103
IO_104
IO_111
IO_112
IO_113
IO_114
IO_115
IO_116
IO_119
IO_120
IO_121
IO_122
IO_125
IO_126
IO_127
IO_128
IO_131
IO_132
IO_133
IO_134
IO_135
IO_136
IO_139
IO_140
IO_141
IO_142
IO_143
IO_144
See the GEHC Myworkshop System to determine the status of this document.
IO_56
IO_57
IO_58
IO_60
IO_62
IO_63
IO_64
IO_65
IO_67
IO_68
IO_69
IO_70
IO_73
IO_74
IO_75
IO_83
IO_85
IO_86
IO_87
IO_88
IO_89
IO_90
IO_92
IO_93
IO_94
IO_95
IO_96
IO_97
IO_99
IO_61
IO_71
RS2_INT
56
58
60
62
63
64
65
68
69
83
85
86
88
89
90
92
93
94
95
96
99
70
73
74
75
57
67
87
97
61
71
RS2_CH_WR
RS2_CH_RD
RS2_RESET
RS2_CS
3
0
2
4
5
6
7
1
RS1_DATA<7..0> RS2_CLOCK
0
2
1
RS2_ADDR<2..0>
0
2
1
RS1_ADDR<2..0>
3
0
2
4
5
6
7
1
RS2_DATA<7..0>
RS1_CLOCK
RS1_CS
RS1_RESET
RS1_CH_RD
RS1_CH_WR
RS1_INT
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
fpga 2 of 5 5436648SCH 2 16 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
RS_VCC
U19
TL16C550CPT C13 C16
VCC 1U 1U
A 25V 25V PLACE 0.1UF CAP BETWEEN VCC AND GND A
5 RCLK BAUDOUT_N 12 10% 10% U23
R77 MAX232E
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
41 RI_N OUT2_N 31 1%
24 ADS_N GND 15
RS1_RESET 35 MR DDIS 22 RS_VCC
A
RS1_CH_RD 19 RD1_N TXRDY_N 23 RS_GND
20 RD2 RXRDY_N 29 U22
RS1_CH_WR 16 A
WR1_N R84
B 17 WR2 INTRPT 30 RS1_INT VCC TCMT4100 475 RS_GND B
0.125W
1%
VCC=VCC;GND=GND U21 12 5
R79
SN74ACT14
4.99K 2 1 11 6
0.125W B A
1%
VCC=VCC;GND=GND
R82
4.99K
0.125W VCC
1%
U20 U22
TL16C550CPT R85
VCC 475
0.125W
TCMT4100 RS_VCC
5 RCLK BAUDOUT_N 12 1%
R78 U21 3 14
4.99K RS2_CLOCK 14 XIN SN74ACT14
0.125W 15 XOUT
C 1% D0 43 0 RS2_DATA<7..0> C
9 CS0 D1 44 1 3 A B 4 4 13
10 CS1 D2 45 2
RS2_CS 11 CS2_N D3 46 3 R87
D4 47 4 VCC=VCC;GND=GND 4.99K
RS2_ADDR<2..0> 0 28 A0 D5 2 5 0.125W
1 27 A1 D6 3 6 1%
2 26 A2 D7 4 7
VCC=VCC;GND=GND
VCC=VCC;GND=GND R86
R80 4.99K
D 0.125W
1%
D
4.99K
0.125W
REV 2 1July04
1%
B Size
Block Path Block Sheet Dwg No Rev Sheet
fpga 3 of 5 5436648SCH 2 17 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
VCC
RS3_TXD 9 A B 8 8 9 RS_VCC
VCC=VCC;GND=GND R95
4.99K
0.125W C17 C21
1% 1U 1U
25V 25V PLACE 0.1UF CAP BETWEEN VCC AND GND
10% 10% U27
A
MAX232E
RS_GND
A
RS_GND 16 VCC
RS_VCC C20 2 VP
See the GEHC Myworkshop System to determine the status of this document.
1U 6 VN
C18 25V
1U 10% 1 C1P
U25 R96 25V 3 C1M
VCC TCMT4100 475 10% 4 C2P
0.125W 5 C2M
1% CH52
B U21 12 5 11 T1IN T1OUT 14 CH54 CPI_CONSOLE_RS1_RXD
OUT B
12 R1OUT R1IN 13 CPI_CONSOLE_RS1_TXD
SN74ACT14 OUT
CH53
10 T2IN T2OUT 7 CH55 CPI_CONSOLE_RS2_RXD
OUT
RS3_RXD 10 B A 11 11 6 9 R2OUT R2IN 8 CPI_CONSOLE_RS2_TXD
OUT
GND 15
VCC=VCC;GND=GND R94
4.99K
0.125W A
1% VCC RS_GND
U25 RS_VCC
R97
475 TCMT4100
0.125W
1%
U21 3 14
SN74ACT14
RS4_TXD 13 12 4 13
C A B C
VCC=VCC;GND=GND R99
4.99K
0.125W
1%
A
RS_GND
RS_VCC
U25
R100
VCC 475
TCMT4100 0.125W
1%
U26 16 1
SN74ACT14
RS4_RXD 2 B A 1 15 2
D D
VCC=VCC;GND=GND R98
4.99K
0.125W
REV 2 1July04
1%
B Size
Block Path Block Sheet Dwg No Rev Sheet
fpga 4 of 5 5436648SCH 2 18 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
VCC VCC
VCC VCC
R164 R168 R170 R173 R176 R184 R186 R189 R197 R200 R202 R207 R209 R211 R213 R215
R140 R144 R149 R153 R157 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K
4.99K 4.99K 4.99K 4.99K 4.99K 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W
0.125W 0.125W 0.125W 0.125W 0.125W 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1%
A 1% 1% 1% 1% 1% A
10
12
13
11
3
3
0
9
7
7
1
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
0
1
1
VCC
SFD_24V_CMD<2..0> DIGITAL_OUTPUT1<1..0> SFD_INPUT<7..0>
VCC
R145 R171 R174 R177 R185 R187 R190 R198 R201 R203 R208 R210 R212 R214
OVERHEAT_ALARM 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K
0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W
4.99K 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1%
0.125W
1%
14
15
16
18
19
20
22
23
24
25
26
17
21
VCC VCC
DIGITAL_OUTPUT4<26..0>
R141 R146 R150 R154 R158 R161 R165 R169
See the GEHC Myworkshop System to determine the status of this document.
3
0
4
1
1
0.125W 0.125W 0.125W
1% 1% 1%
B DIGITAL_OUTPUT5<2..0> DIGITAL_OUTPUT3<4..0> VCC VCC B
R179 R193 VCC
RS1_CS RS2_CS R205
RS4_TXD
VCC 4.99K 4.99K
0.125W 0.125W 4.99K
1% VCC 1% VCC 0.125W
1%
R180 R194
R106 R142 R147 R151 R155 R159 R162 R166 RS1_RESET RS2_RESET
4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K 4.99K
0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 0.125W 4.99K 4.99K
1% 1% 1% 1% 1% 1% 1% 1% 0.125W 0.125W
1% VCC 1% VCC
R181 R195
3
0
7
1
RS1_CH_RD RS2_CH_RD
12
13
14
15
11
8
2
1
1
RS1_ADDR<2..0> RS2_ADDR<2..0>
D D
REV 2 1July04
Made By Date Title
GE Healthcare
Ma Yongsong 10-JAN-13 Console I/F Company Restricted
B Size
Block Path Block Sheet Dwg No Rev Sheet
fpga 5 of 5 5436648SCH 2 19 of 19
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
A A
REVISION ECR/ECO DATE SIGN OFF
1 19-JULY-12 MA YONGSONG NOTES:
ECR2151208 22-JUN-13 MA YONGSONG
1. THE VARIATION AND VERSION FOR THIS
2 PWA IS 5451492.
2. THIS COVER SHEET CONTROLS THE RE-
Revison notes: VISION STATUS OF THE ENTIRE DOCUMENT.
THE REVISION OF ALL SHEETS OF THIS
The change list of revison1 to revison2 as follows:
DOCUMENT WILL BE AT THE SAME LEVEL.
1. Use global GEPN for CS4344-CZZ use on U8,Global GEPN is 5454247 3. THIS SCHEMATIC MEETS THE SPECIFICA-
2. CR17,CR22,CR23,CR24 change 2408243 to 2408243-2 TIONS OF THE GLOBAL SCHEMATIC STANDARD
GUIDELINES 2299773GSP.
3. CR13,CR14 change 2408243-2 to 5483033
4. ELECTRONIC SIGNATURES FOR BOTH THE
4. CR15,CR16,CR18,CR19,CR20,CR21 no welding
SCHEMATIC REVIEWER(S) AND APPROVER(S)
5. FL11 no welding CAN BE FOUND WITHIN MY WORKSHOP.
6. FL2 change 2378407-4 to 5482604 5. UNLESS OTHERWISE SPECIFIED:
7. R57 should be weld with 5160167 RESISTORS ARE IN OHMS.
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
C C
D D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
intercom 1 of 6 5451492SCH 2 1 of 6
1 2
Approved Document - 5451492SCH_r2.pdf Page 2 of 7
3 4 5 6 7 8
1 2 3 4 5 6 7 8
12V
FL2 R85 TP8
J1 NFM41PC155B1E3 TIN
THE USED PN IS 5482604 2K
D1
1 1 3 0.1W TP2
1 MURS120 MH1 MH2 MH3 MH4
2 1%
2 MH3_50RD5_00 MH3_50RD5_00 MH3_50RD5_00 MH3_50RD5_00
3 3 1.5UF 3V3 TIN J4
R31 TP9
4
200V
PIN VR1 TIN A1 1
2K
RIGHT_ANGLE LT1117-3V3
R12
0.1W
0.1W
A A
511
WIRE_TO_BOARD 12V
1%
1%
PIN
3 VIN VOUT1 2 STRAIGHT
VOUT2 4 TAB
2
DS1
HSMG-C190
ADJ_GND 1 TP3
0.1U
0.1U
100U
16V
10%
16V
10%
10U
25V
10%
10V
10%
C2
C4
C7
C5
GREEN
TIN
3.3V
1
R32
CR16
CR15 GBLC12C
GBLC12C 12V_STAND_OFF 2K
12V_STAND_OFF TPA_SHUT 0.1W
RESERVE, NOT WELDING
1%
3V3
RESERVE, NOT WELDING
TPA_GAIN0
Y1
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
C11
C13
C15
C17
C19
C21
TPA_GAIN1
101
102
103
104
105
106
107
108
3V3 FL1
73
74
75
76
77
78
79
80
81
84
85
86
87
88
93
94
95
96
97
98
BMB0603-A-121 R10
1 2 4 VCC VOUT 3 CLK
IO_73
IO_74
IO_75
IO_76
IO_77
IO_78
IO_79
IO_80
IO_81
IO_84
IO_85
IO_86
IO_87
IO_88
IO_93
IO_94
IO_95
IO_96
IO_97
IO_98
IO_101
IO_102
IO_103
IO_104
IO_105
IO_106
IO_107
IO_108
R5
120 OHM 1 2 22.1
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
ENABLE GND 0.1W
50V
10%
50V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
C60
10N
10N
C12
C14
C16
C18
C20
C23
C1
C3
R30
0.1W
10K 1% TP1 3V3
2K
1%
0.1W
24.576MHZ
1%
B TIN VCCINT<3..0> B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
VCCIO1<1..0>
VCCIO2<1..0>
VCCIO3<1..0>
VCCIO4<1..0> 3V3
FL3
BMB0603-A-121 18
CLK IO_18_GCLK0 IO_109 109
3V3
1 2 20 IO_20_GCLK1 IO_110 110
89 IO_89_GCLK2 IO_111 111
R13
R14
R15
0.1W
0.1W
0.1W
120 OHM 91 112
IO_91_GCLK3 IO_112
2K
1%
2K
1%
2K
1%
60 IO_60_NDEV_OE IO_113 113
RESET 61 IO_61_NDEV_CLR IO_114 114
R17
R18
R20
R22
See the GEHC Myworkshop System to determine the status of this document.
0.1W
0.1W
0.1W
0.1W
50V
10%
50V
10%
C61
10N
C62
10N
IO_117 117
2K
1%
2K
1%
2K
1%
2K
1%
TDI 34 TDI IO_118 118 A_MCLK
TMS 33 TMS IO_119 119 A_SCLK
TCK 35 TCK IO_120 120 A_LRCK
10U
25V
10%
TDO 36 TDO IO_121 121 A_SDOUT
C6
IO_122 122 D_MCLK
1 IO_1 IO_123 123 D_SCLK
RESET 2 U2 124 D_LRCK
IO_2 IO_124
3 EPM1270T144C5 125 D_SDIN
IO_3 IO_125
3V3 4 IO_4 IO_127 127
0.1W
R6
10K
5 IO_5 IO_129 129
1%
C 6 IO_6 IO_130 130 C
7 IO_7 IO_131 131
8 IO_8 IO_132 132
11 IO_11 IO_133 133
12 IO_12 IO_134 134 3V3 3V3 3V3
0.1W
0.1W
0.1W
0.1W
R1
R2
R3
R4
1%
2K
1%
2K
1%
2K
1%
R16
R19
R21
0.1W
0.1W
0.1W
511
511
511
16 IO_16 IO_140 140
1%
1%
1%
21 IO_21 IO_141 141 422_R
TCK 1 1 2 2 22 IO_22 IO_142 142 EN_422_R
0.1U
16V
10%
TDO 3 3 4 4 C8 23 IO_23 IO_143 143 422_T
TMS 5 6 24 144 EN_422_T
2
5 6 IO_24 IO_144
DS2
HSMG-C190
DS3
HSMG-C190
DS4
HSMG-C190
7 7 8 8 27 IO_27
TDI 9 9 10 10 28 IO_28 GNDI0<7..0>
GREEN
GREEN
GREEN
29 IO_29 GNDINT<3..0>
30 IO_30
1
PIN 31 IO_31
STRAIGHT 32 IO_32
RIBBON_CABLE_LOW_PROFILE LED1
LED2
IO_37
IO_38
IO_39
IO_40
IO_41
IO_42
IO_43
IO_44
IO_45
IO_48
IO_49
IO_50
IO_51
IO_52
IO_53
IO_55
IO_57
IO_58
IO_59
IO_62
IO_63
IO_66
IO_67
IO_68
IO_69
IO_70
IO_71
IO_72
LED3
3V3
M/S
37
38
39
40
41
42
43
44
45
48
49
50
51
52
53
55
57
58
59
62
63
66
67
68
69
70
71
72
D SHUT_S D
R11
0.1W
0.1W
0.1W
0.1W
R7
R8
R9
SHUT_M
2K
1%
2K
1%
2K
1%
2K
1%
ADJ_CS
REV 2 01July04
ADJ_SCLK
ADJ_DIN ADJ_DOUT
ADJ_DOUT ADJ_DIN
ADJ_SCLK
ADJ_CS GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
intercom 2 of 6 5451492SCH 2 2 of 6
1
Approved Document - 5451492SCH_r2.pdf Page 3 of 7
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
3V3
CR3
GBLC05C
A 3V3 FL8
A
BMB0603-A-121
R34
R23
R24
0.1W
0.1W
0.1W
1 2
2K
1%
2K
1%
2K
1%
S1
120 OHM
219-04MST J3
5V_STAND_OFF
0.1U
0.1U
16V
10%
16V
10%
C71
C94
1 I1 O1 8 1 1
2 2
2 I2 O2 7 SHUT_SALVE
CR4
C107
C108
GBLC05C
25V
10%
10V
10%
22N
3 I3 O3 6 MASTER/SLAVE PIN
1U
RIGHT_ANGLE 1 1 J5
4 I4 O4 5 TERMINAL_BLOCK_HEADER 2 2
0.1U
0.1U
16V
10%
16V
10%
C33
C34
3 3
SHUT_MASTER
PIN
5V_STAND_OFF RIGHT_ANGLE
U3 WIRE_TO_BOARD
74LVC-LCX04
2
Y<1> A<1>
M/S 12 Y<0> A<0> 13 0.1U
BMB0603-A-121
16V
10%
VCC=3V3;GND=GND
120 OHM
FL6
1
See the GEHC Myworkshop System to determine the status of this document.
3V3 FL7
0.1U
16V
10%
C10
BMB0603-A-121
10V
10%
C98
1 2
1U
3V3
120 OHM
0.1U
0.1U
16V
10%
16V
10%
C65
C82
U4
ADC124S101
0.1U
16V
10%
C95
ADJ_SCLK 10 SCLK VA 2
C C
ADJ_CS 1 CS_N IN1 7 1 1 J6
IN2 6 2 2
ADJ_DIN 8 DIN IN3 5 3 3
ADJ_DOUT 9 DOUT IN4 4
3 GND PIN
RIGHT_ANGLE
WIRE_TO_BOARD
D D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
intercom 3 of 6 5451492SCH 2 3 of 6
1
Approved Document - 5451492SCH_r2.pdf Page 4 of 7
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
D3
D2 MURS120
MURS120
TP4 TP5
3V3_A
5V TIN 200V R82 TIN
200V R79
12V VR3
2K
A VR2 LT1117-3V3 A
R25
0.1W
2K 0.1W
511
12V LT1117CST-5
1%
R33
0.1W
0.1W 1%
1K
1%
1% 3 2
VIN VOUT1
3 VIN VOUT1 2 VOUT2 4
4
2
VOUT2
DS6
HSMG-C190
1
2
ADJ_GND
0.1U
0.1U
100U
DS5
HSMG-C190
16V
10%
16V
10%
C37
10U
25V
10%
C39
C40
C45
10V
10%
ADJ_GND 1
GREEN
0.1U
0.1U
100U
16V
10%
16V
10%
C22
10U
25V
10%
C25
C27
C31
10V
10%
GREEN
3.3V
1
5V R44 R46
1
2.49K 1.02K
0.1W 0.1W
1% 1%
R40 R41
2.49K 1.02K
C28 0.1W 0.1W
1% 1%
4
VN
VN
1U
10V 6 6
3V3_A R36 R38 7 R42 R43 7 FILTER_OUT
10% FILTER_IN 5 5
B C29 B
VP
VP
OP284 OP284
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
8
U1
8
U5
0.1W 0.1W 0.1W 0.1W
10N 1% 1% 1% 1%
R28
0.1W
50V
511
R68 5V
1%
10%
50V
10%
25V
10%
50V
10%
C57
C46
10N
C51
15N
C53
10N
0
5V 0.1W 1U
6.8N
+0.05 10V
50V
10%
C35
R29
0.1W
C32 10%
511
1%
C59
See the GEHC Myworkshop System to determine the status of this document.
R69
R80
0.1W
50V
1U
C30
10P
20K
5%
1%
10V 10N
10% 4.99K 50V
C36 0.1W 10%
1%
R39
3V3
R35 C42 R47
10N FILTER_OUT A_SDOUT
50V 2K
1U
C111
8
R77 U6
4.99K
OP284
R37
R45
VP
RIGHT_ANGLE
0.1W
180P
0.1W
50V
C44
10K
MIC- 3
1%
R48
1%
1%
1 FILTER_IN cs5343 A_SCLK
J7
33N 51.1
PIN
2
2.21K
R27
0.1W
0.1W 22.1
VN
25V 6 1
1%
AINL SDOUT
10% 1% 0.1W
1
2
3
4
C113
1%
10V
10%
8 2
1U
AINR SCLK
1
2
3
R49
3V3_A
R81 10 VA LRCK 3 A_LRCK
C110 R78
MIC+ 7 4 22.1
VQ MCLK
20K 0.1W
33N 51.1 0.1W 9 5 1%
GND FILT+
C112
25V 0.1W 1%
10V
10%
R50
1U
16V
10%
C24
C26
GBLC05C GBLC05C
1U
1U
D 5V_STAND_OFF 5V_STAND_OFF 35V D
10%
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
intercom 4 of 6 5451492SCH 2 4 of 6
1
Approved Document - 5451492SCH_r2.pdf Page 5 of 7
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
TP7
R59
0.1W
0.1W
1K
1%
1% 5V_ISO
U9
DCR010505U
A A
0.1U
C100
0.1U
C101
0.1U
C102
0.1U
DS7
HSMG-C190
16V
10%
16V
10%
16V
10%
16V
10%
C99
1 VS1 VOUT 14 12V_STAND_OFF
2 VS2
GREEN
RESERVE, NOT WELDING
0.1U
0.1U
16V
10%
10V
10%
16V
10%
C52
10U
25V
10%
C67
C54
C58
10U
25V
10%
C74
ERROR_N 17 TP6
1U
28 SYNCIN VREC 12
CR21
1
26 0VIN1 ENABLE 16 R84 TIN
27 13 P GBLC12C
0VIN2 0VOUT
NFM41PC155B1E3
12V_STAND_OFF 12V
1.5UF
5V_ISO RESERVE, NOT WELDING
C72
3
R64
P
5V_ISO U13 4
U10 0.1U R58 MAX13088
FL11
16V 121 2
ADUM1100
P
10% 0.1W
0.0625W
0.0625W
3V3 FL9
R55
R61
R63
0.1W
4.7K
0.1%
4.7K
0.1%
C66 4.7K 8 1%
1
VCC DR221-333AE
2K
1%
1 8 0.0625W 1 4
VDD1A VDD2
U7 3 0.1% 1 RO
VDD1B
EN_422_T 1 74LVC125A 0.1U U12 2 RE_N B 7
3 16V 2 1 74VHC-AHC125 3 DE A 6
_N 10%
B 422_T 2 Y _N 3 4 DI 2 3 B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
VIN VOUT
A 6 2 Y
VCC=3V3;GND=GND A GND 5 1K OHMS AT 10MHZ
4 GND1 GND2A 5 VCC=5V_ISO;GND=GND_POWER
GND2B 7 J8
P
P
1 1
6 2
5V_ISO
R60 6 2
5V_ISO 7 7 3 3
C73 R65 8 8 4 4
R56
0.1W
P 4.7K 5V_ISO 9 5
U11 U14 9 5
2K
1%
P
See the GEHC Myworkshop System to determine the status of this document.
3V3 0.0625W
ADUM1100 MAX13088
0.1U 0.1% 121 P G1
G1
C69 16V U12 0.1W G2
FL10 G2
EN_422_R 8 1 10% 74VHC-AHC125 4 8 1%
VDD2 VDD1A VCC DR221-333AE
VDD1B 3 6 OE 1 4
U7 0.1U Y 5 1 RO PIN
74LVC125A 4 16V 2 A 2 RE_N B 7 RIGHT_ANGLE
422_R 6 10% 3 DE A 6
OE VOUT VIN VCC=5V_ISO;GND=GND_POWER STD_DENSITY
Y 5 6 4 DI 2 3
A
0.0625W
0.0625W
VCC=3V3;GND=GND 5 GND2A GND1 4 GND 5 1K OHMS AT 10MHZ
C C
P
R62
R67
4.7K
0.1%
4.7K
0.1%
7 GND2B
P CR17 CR22
3V3 3V3 GBLC12C GBLC12C
0.1U
0.1U
16V
10%
16V
10%
C96
C97
12V_STAND_OFF 12V_STAND_OFF
CR23
GBLC12C
CR18
GBLC05C
R57
5V_STAND_OFF 12V_STAND_OFF
RESERVE, NOT WELDING
0
1W CR24
+0.05 GBLC12C
D CR19 D
GBLC05C
REV 2 01July04
5V_STAND_OFF 12V_STAND_OFF
RESERVE, NOT WELDING
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
intercom 5 of 6 5451492SCH 2 5 of 6
1
Approved Document - 5451492SCH_r2.pdf Page 6 of 7
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
3V3_A
10N
C55
10%
50V
10%
35V
C56
1U
0.1U
16V
10%
C63
10U
25V
10%
C80
U8
A CS4344-CZZ A
R51
D_SDIN 10%
25V 9 VA AOUTL 7
22.1 10U 5 VQ
0.1W 6 FILTP
1% C70 R74
R52 C68 1 SDIN AOUTR 10
D_SCLK 2 NDEM_SCLK
475
0.0625W
3 LRCK 3.3U
R72
R73
274K
0.1W
0.1%
2.7N
22.1 0.1W
50V
16V
10K
C84
4 8
1%
MCLK GND
1%
0.1W 10% 1%
1%
R53
D_LRCK
22.1
0.1W
1%
R54
D_MCLK
22.1
0.1W
1%
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
12V
FL12 12V FL13
BLM21PG331SN1 BLM21PG331SN1
1 2 1 2
330 OHM 330 OHM
C105
C106
50V
10%
50V
10%
10N
10N
C103
C104
50V
10%
50V
10%
10N
10N
C85
See the GEHC Myworkshop System to determine the status of this document.
U17 10U
TPA3007D1 25V
10%
C81 C83 C86
24 VCC VCLAMP 7
C78
1U 23 VREF BSN 8 1U 1U
0.47U
A
P6SMB130A
25V
CR1
25V 25V
25V
16V
10%
C76
C90
C92
5%
U15
1N
10% 10% 10%
130V
74LVC-LCX04 C75 1U 1 INN BSP 17
ANALOG 25V 2 INP
0.47U 10% 9 FL4
33U
20%
PVCC1
C C
L2
5A
1 A<5> Y<5> 2 0.47U 16V 5 SHUTDOWN_N PVCC2 16 R75 C88 BLM31P500S J9
3 4 16V 10% 3 1 2
A<4> Y<4> GAIN0
5 6 10% 4 10
A<3> Y<3> GAIN1 OUTN1
TPA_SHUT 9 8 C79 11 51.1 0.22U 70 OHM /3A 1
A<2> Y<2> OUTN2 1
TPA_GAIN0 11 10 22 0.1W 25V 2
A<1> Y<1> BYPASS 2
A
33U
20%
A<0> Y<0> OUTP1
L3
5A
1U 21 COSC OUTP2 15 R76 C89 BLM31P500S
C77 25V 20 ROSC 1 2 PIN
A
10% 6
VCC=3V3;GND=GND PGND1 RIGHT_ANGLE
P6SMB130A
18 12 51.1 0.22U 70 OHM /3A
AGND1 PGND2 WIRE_TO_BOARD
220P 19 13 0.1W 25V
AGND2 PGND3
0.47U
130V
A
50V 1% 10%
25V
16V
10%
C91
C93
5%
1N
5%
CR2
R70 12V
C87
+0.05
16V
10%
C9
D D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
intercom 6 of 6 5451492SCH 2 6 of 6
1
Approved Document - 5451492SCH_r2.pdf Page 7 of 7
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
C C
D D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
root 1 of 2 5446243SCH 2 1 of 15
1 2 3 4 5 6 7 8
Approved Document - 5446243SCH_r2.pdf Page 2 of 16
1 2 3 4 5 6 7 8
I2
9PSLD ID NO+ ID NO+
9PSLD
A 1ST TUBE KEY_MATRIX_OUT_DIFF<7..0>
A
1ST TUBE KEY_MATRIX_OUT_DIFF<7..0>
3PSLD WATCH_DOG WATCH_DOG
3PSLD
4PSLD 11PSLD
4PSLD 11PSLD
5PSLD 12PSLD
5PSLD 12PSLD
10PSLD 13PSLD
10PSLD 13PSLD
7PSLD KEY_MATRIX_IN0
7PSLD KEY_MATRIX_IN0
8PSLD KEY_MATRIX_IN1
8PSLD KEY_MATRIX_IN1
2PSLD KEY_MATRIX KEY_MATRIX_IN2
2PSLD KEY_MATRIX_IN2
6PSLD KEY_MATRIX_IN3
6PSLD KEY_MATRIX_IN3
KEY_SEL0
KEY_SEL0
ABNORMAL ABNORMAL KEY_SEL1
KEY_SEL1
CONSOLE_POWER CONSOLE_POWER KEY_SEL2
KEY_SEL2
KEY_MATRIX_IN_DIFF<7..0> KEY_MATRIX_IN_DIFF<7..0> KEY_SEL3
KEY_SEL3
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
I1
331CN_32 331CN_32 9PSLD
9PSLD
CHIP_SEL_DIFF<7..0> CHIP_SEL_DIFF<7..0> 3PSLD I3
C 3PSLD C
DATA_HIGH_DIFF<7..0> DATA_HIGH_DIFF<7..0> 4PSLD EMERGENCY EMERGENCY 1ST TUBE 1ST TUBE
4PSLD
DATA_LOW_DIFF<7..0> DATA_LOW_DIFF<7..0> 5PSLD F_ON F_ON ABNORMAL ABNORMAL
5PSLD
WATCH_DOG WATCH_DOG 10PSLD F_POSITION F_POSITION CHIP_SEL_DIFF<7..0> CHIP_SEL_DIFF<7..0>
10PSLD
Y5 Y5 7PSLD ID NO+ ID NO+ CONSOLE_POWER CONSOLE_POWER
7PSLD
Y6 Y6 8PSLD KEY_MATRIX_OUT_DIFF<7..0> KEY_MATRIX_OUT_DIFF<7..0> DATA_HIGH_DIFF<7..0> DATA_HIGH_DIFF<7..0>
8PSLD
11PSLD
LED_DISPLAY
2PSLD R_ON R_ON CONNECTOR DATA_LOW_DIFF<7..0> DATA_LOW_DIFF<7..0>
11PSLD 2PSLD
12PSLD 6PSLD R_POSITION R_POSITION KEY_MATRIX_IN_DIFF<7..0> KEY_MATRIX_IN_DIFF<7..0>
12PSLD 6PSLD
13PSLD TECH SPOT TECH SPOT
13PSLD
KEY_MATRIX_IN0 F_ON F_ON X-RAY ON X-RAY ON
KEY_MATRIX_IN0
KEY_MATRIX_IN1 F_POSITION F_POSITION Y5 Y5
KEY_MATRIX_IN1
KEY_MATRIX_IN2 R_ON R_ON Y6 Y6
KEY_MATRIX_IN2
KEY_MATRIX_IN3 R_POSITION R_POSITION 331CN_32 331CN_32
KEY_MATRIX_IN3
KEY_SEL0 EMERGENCY EMERGENCY
KEY_SEL0
D KEY_SEL1
D
KEY_SEL1
REV 2 01July04
KEY_SEL2
KEY_SEL2
KEY_SEL3
KEY_SEL3
KEY_SEL4
KEY SEL4
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
root 2 of 2 5446243SCH 2 2 of 15
1 2
Approved Document - 5446243SCH_r2.pdf Page 3 of 16
3 4 5 6 7 8
1 2 3 4 5 6 7 8
A DATA_LOW_DIFF<7..0> A
2C1^ IN
R17 U10
1 DS26LV32AT
3V3 DATA_HIGH_DIFF<7..0>
R1 2C1^ IN
332 1K
0.125W 0.125W 16
R9 VCC DATA_BUS<7..0> R33 U12
0 1% 1% 1 DS26LV32AT
R18 4 EN R25 3V3
3 1K 12 332 1K
EN_N DATA_BUS<7..0>
0.125W 0.125W 0.125W 16
R2 R29 VCC
332 1% 1K 2 3 0 0 1% 1%
INP<3> O<3>
0.125W 0.125W 1 4
R10 INN<3> R34 EN
2 1% 1% 6 5 1 3 1K 12
INP<2> O<2> EN_N
7 0.125W
INN<2> R26
1K 10 11 2 332 1% 1K 2 3 4
R19 INP<1> O<1> INP<3> O<3>
5 0.125W 9 0.125W 0.125W 1
INN<1> R30 INN<3>
1% 14 13 3 2 1% 1% 6 5 5
R3 INP<0> O<0> INP<2> O<2>
332 1K 15 7
INN<0> INN<2>
0.125W 0.125W 8 1K 10 11 6
R11 GND R35 INP<1> O<1>
4 1% 1% 5 0.125W 9 INN<1>
1% 14 13 7
R20 R27 INP<0> O<0>
7 1K 332 1K 15 INN<0>
0.125W 0.125W 0.125W 8
R4 R31 GND
332 1% 1K 4 1% 1%
0.125W
B 0.125W R12 R36 B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
6 1% 1% 7 1K
0.125W
R28
1K 332 1% 1K
0.125W 0.125W 0.125W
R32
1% 6 1% 1%
1K
0.125W
1%
See the GEHC Myworkshop System to determine the status of this document.
0 R37 0 0
1 R47 0 1
2 R48 0 2
3 R49 0 3
4 R50 0 4
CHIP_SEL_DIFF<7..0> 5 R51 0 5
2C1^ IN 6 0 6
R52
R21 U11 7 R53 0 7
DATA_BUS<7..0> DATA_BUS_OUT<7..0>
1 DS26LV32AT 0.1W +0.05
R5 3V3
332 1K
C 0.125W R13
0.125W 16 VCC
C
0 1% 1%
R22 4 EN
3 1K 12 CHIP_SEL_CPLD<3..0> CHIP_SEL_INV<7..0>
EN_N
0.125W
R6
332 1% 1K 2 3 0
INP<3> O<3>
0.125W 0.125W 1
R14 INN<3>
2 1% 1% 6 5 1 1
INP<2> O<2>
7 INN<2> 4
1K 10 11 2 5
R23 INP<1> O<1>
5 0.125W 9 INN<1>
1% 14 13 3
R7 INP<0> O<0>
332 1K 15 INN<0>
0.125W 0.125W 8
R15 GND
4 1% 1% C1 C2 C3
R24 27N 27N 27N
7 1K 50V 50V 50V
0.125W 10% 10% 10%
R8
332 1% 1K
0.125W 0.125W
R16
6 1% 1%
1K
0.125W
1%
D D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
led_display 1 of 7 5446243SCH 2 3 of 15
1 2
Approved Document - 5446243SCH_r2.pdf Page 4 of 16
3 4 5 6 7 8
1 2 3 4 5 6 7 8
12V
2
DS1 DS2 DS3 DS4
U1
74VHC-AHC373 U3
1
DATA_BUS_DRV1<7..0> TCMT4100
DATA_BUS_DRV1<7..0>
U2
1 OE_N ULN2803ADW R39
CHIP_SEL_INV<4> 11 1 16 F_POSITION
CLK OUT 2D3^
0 3 2 1 18 0 1K
D<7> Q<7> I1 O1
1 4 5 2 17 1 0.125W
D<6> Q<6> I2 O2
2 7 D<5> Q<5> 6 3 I3 O3 16 2 0 R40 2 15
3 8 D<4> Q<4> 9 4 I4 O4 15 3 3 14 R_POSITION 2D3^
13 12 5 14 OUT
4 D<3> Q<3> I5 O5 4
5 14 15 6 13 5 1K
D<2> Q<2> I6 O6
6 17 16 7 12 6 12V 0.125W
D<1> Q<1> I7 O7
7 18 D<0> Q<0> 19 8 I8 O8 11 7 1 R41 4 13
10 5 12 F_ON
OUT 2D3^
DATA_BUS_OUT<7..0> COMMON
9 1K
VCC=3V3;GND=GND GND
0.125W
P G12 2 R42 6 11
7 10 R_ON 2D3^
OUT
1K
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
0.125W
3 8 9 Y5
IN 2C1^
See the GEHC Myworkshop System to determine the status of this document.
12V
1K
0.125W
5 R45 4 13
5 12 R_ON
1K
0.125W
6 R46 6 11 Y6 IN 2C1^
7 10 EMERGENCY 2D3^
OUT
1K
0.125W
2C1^ IN 331CN_32 8 9 Y5
C4
10N
D 50V
10%
D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
led_display 2 of 7 5446243SCH 2 4 of 15
1
Approved Document - 5446243SCH_r2.pdf Page 5 of 16
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
DATA_BUS_DRV3<6..0> DATA_BUS_DRV3<7..0>
9PSLD: COLLIMATOR ADJUST SEMI-AUTO
3PSLD:LOW-CONTRAST
4 R68 1K 9PSLD
0 R58 1K 3PSLD 2C3^ OUT 2C3^
OUT 0.5W 5%
0.5W 5%
R227 1K
U15 R222 1K
A 74VHC-AHC373
0.5W 5% 0.5W 5% A
U18
1 OE_N ULN2803ADW 7PSLD: COLLIMATOR ADJUST AUTO
CHIP_SEL_INV<1> 11 CLK DATA_BUS_DRV3<6..0> 4PSLD: HIGH-CONTRAST
5 R69 1K 7PSLD
0 3 D<7> Q<7> 2 1 I1 O1 18 0 1 R59 1K 4PSLD 2C3^ OUT 2C3^
4 5 2 17 OUT 0.5W 5%
1 D<6> Q<6> I2 O2 1 0.5W 5%
2 7 D<5> Q<5> 6 3 I3 O3 16 2 R228 1K
3 8 9 4 15 3 R223 1K
D<4> Q<4> I4 O4 5%
4 13 D<3> Q<3> 12 5 I5 O5 14 4 5% 0.5W
0.5W
5 14 D<2> Q<2> 15 6 I6 O6 13 5
6 17 D<1> Q<1> 16 7 I7 O7 12 6 12V
7 18 D<0> Q<0> 19 8 I8 O8 11 8PSLD: REMOTE/LOCAL SWITCH
5PSLD: EVEN HIGH-CONTRAST
10
6 R70 1K 8PSLD
COMMON 2 R60 1K 5PSLD 2C3^ OUT 2C3^
VCC=3V3;GND=GND GND 9 OUT 0.5W 5%
DATA_BUS_OUT<7..0> 0.5W 5%
R226 1K
P G12 R224 1K
0.5W 5%
0.5W 5%
3 R61 1K 10PSLD
OUT 2C3^
B 0.5W 5% B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
R225 1K
U16 5%
74VHC-AHC373 DATA_BUS_DRV5<4..0> 0.5W
U19
1 OE_N ULN2803ADW DS5 12V
CHIP_SEL_INV<5> 11 CLK
HLMP-2755
0 3 D<7> Q<7> 2 1 I1 O1 18 0
1 4 D<6> Q<6> 5 2 I2 O2 17 1
DS5: B INDICATOR 1 2
2 7 6 3 16 2 CA AA
See the GEHC Myworkshop System to determine the status of this document.
D<5> Q<5> I3 O3
3 8 D<4> Q<4> 9 4 I4 O4 15 3 4 3
4 13 D<3> Q<3> 12 5 I5 O5 14 4 CB AB
5 14 D<2> Q<2> 15 6 I6 O6 13 R75 1K 5 6
6 17 D<1> Q<1> 16 7 I7 O7 12 12V 0.1% CC AC
18 19 0.25W
7 D<0> Q<0> 8 I8 O8 11 DATA_BUS_DRV5<0> 1K
R76 8 7
10 0.1% CD AD DATA_BUS_DRV5<7..0>
0.25W
DATA_BUS_OUT<7..0> COMMON 2PSLD: F1
VCC=3V3;GND=GND GND 9
YELLOW
P G12 3 R71 1K 2PSLD
C DS6 0.5W 5%
OUT C
HLMP-2755
R230 1K
1 2 0.5W 5%
DS6: R INDICATOR CA AA
11PSLD: 12' INTENSIFIER MODE
4 3
R55 1K 11PSLD CB AB
OUT R80 1K 5 6 6PSLD: F2
0.5W 5% CC AC
0.1% 0.25W 1K 6PSLD
DATA_BUS_DRV5<1> 1K 8 7 4 R72
R56 1K R77 CD AD OUT
0.1% 0.25W 0.5W 5%
0.5W 5%
U17 D1 R229 1K
ULN2803ADW YELLOW
MURS120T3 5%
200V 0.5W
12PSLD: 9' INTENSIFIER MODE DS7
NOML_LED 1 I1 O1 18 HLMP-2755
MAG1_LED 2 17 R57 1K 12PSLD WDT_DRV
I2 O2 OUT
MAG2_LED 3 I3 O3 16 0.5W 5%
4 I4 O4 15 1 2
D2 CA AA
5 I5 O5 14 R190 1K
6 I6 O6 13 MURS120T3 4 3
0.5W 5% 200V CB AB
7 I7 O7 12
12V 1K
8 I8 O8 11 R78 5 6
0.1% CC AC
10 0.25W
DATA_BUS_DRV5<2> R79 1K 8 7
COMMON
D GND 9 13PSLD: 6' INTENSIFIER MODE 0.1% 0.25W
CD AD D
R191 1K 13PSLD
REV 2 01July04
P OUT YELLOW
0.5W 5%
G12 DS7: F INDICATOR
R192 1K
0.5W 5% GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
led_display 3 of 7 5446243SCH 2 5 of 15
1
Approved Document - 5446243SCH_r2.pdf Page 6 of 16
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
3V3
3V3 PLACE 0.1UF CAP CLOSE TO VCC AND GND
0.125W
0.125W
0.125W
R133
R135
R137
0.1U
16V
10%
16V
10%
16V
10%
C31
10U
C33
C35
3V3 U23
1U
A TL16C550CPT A
1K
1%
1K
1%
1K
1%
0.125W
2
5 12
R113
RCLK BAUDOUT_N U25
MAX3232C
RS1_CLOCK 14 XIN RS1_ADDR<2..0>
15 RS1_DATA<7..0>
XOUT
1K
1%
D0 43 0 16 VCC
9 CS0 D1 44 1 2 VP
10 CS1 D2 45 2 6 VN
0.1U
0.1U
16V
10%
16V
10%
C32
C34
RS1_CS 11 CS2_N D3 46 3
D4 47 4 0.1U C36 1 C1P
RS1_ADDR<2..0> 10%
0
1
28
27
A0
A1
D5
D6
2
3
5
6
16V
0.1U
3
4
C1M
C2P RS232_1 FOR SID
2 26 A2 D7 4 7 C37 5 C2M
R117 16V 10%
RS1_RXD 7 8 RS1_TXD 11 14 232_1_TXD
SIN SOUT T1IN T1OUT J1
10 T2IN T2OUT 7 232_2_TXD
38 33 33 232_1_RXD 13 12 33 R125 RS1_RXD
CTS DTR_N R1IN R1OUT
39 32 0.1W 232_2_RXD 8 9 0.1W 2% 1
DSR_N RTS_N R2IN R2OUT 1
40 34 2% 232_1_TXD CH1 2 6
DCD_N OUT1_N R126 2 6
41 RI_N OUT2_N 31 GND 15 33 RS2_RXD 232_1_RXD CH5 3 3 7 7
24 ADS_N 0.1W 2% 4 4 8 8
RS1_RESET 35 MR DDIS 22 CH3 5 5 9 9
RS1_CH_WR 16 WR1_N
17 WR2 INTRPT 30 RS1_INT
R115 GROUND PIN
1K
STRAIGHT
VCC=3V3;GND=GND STD_DENSITY
0.125W 1% 3V3 3V3
R119 RS2_CLOCK R127
RS1_CLOCK 1K 1K
0.125W 1% 0.125W 1%
3V3
See the GEHC Myworkshop System to determine the status of this document.
0.125W
0.125W
0.125W
3V3 3V3
R134
R136
R138
R120 RS2_CS R128
RS1_CS 1K 1K
3V3 U24
0.125W 1% 0.125W 1%
TL16C550CPT
1K
1%
1K
1%
1K
1%
0.125W
2
5 12
R114
RCLK BAUDOUT_N
3V3 3V3
C RS2_CLOCK 14 XIN R121 R129 RS2_ADDR<2..0> C
15 RS2_DATA<7..0> RS1_RESET 1K RS2_RESET 1K
XOUT
1K
1%
D0 43 0
9 44 1 0.125W 1% 0.125W 1%
CS0 D1
10 CS1 D2 45 2
RS2_CS 11 CS2_N D3 46 3
D4 47 4
RS2_ADDR<2..0> 0 28 A0 D5 2 5 3V3 3V3
1 27 3 6
2 26
A1
A2
D6
D7 4 7 RS1_CH_RD
R122
1K RS2_CH_RD
R130
1K RS232_2 FOR IMAGE INTENSIFIER
RS2_RXD R118
7 8 RS2_TXD 0.125W 1% 0.125W 1%
SIN SOUT J3
38 33 33
CTS DTR_N
39 32 0.1W 1
DSR_N RTS_N CH2 1
40 34 2% 3V3 3V3 232_2_TXD 2 6
DCD_N OUT1_N CH6 2 6
41 RI_N OUT2_N 31 R123 R131 232_2_RXD 3 3 7 7
24 RS1_CH_WR 1K RS2_CH_WR 1K 4 8
ADS_N CH4 4 8
RS2_RESET 35 MR DDIS 22 5 5 9 9
0.125W 1% 0.125W 1%
RS2_CH_RD 19 RD1_N TXRDY_N 23 G1 G1
20 RD2 RXRDY_N 29 G2 G2
RS2_CH_WR 16 WR1_N
17 WR2 INTRPT 30 RS2_INT 3V3 3V3
R116 R124 R132 PIN
1K RS1_INT 1K RS2_INT 1K GROUND STRAIGHT
D 0.125W 1%
VCC=3V3;GND=GND
0.125W 1% 0.125W 1% STD_DENSITY D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
led_display 4 of 7 5446243SCH 2 6 of 15
1
Approved Document - 5446243SCH_r2.pdf Page 7 of 16
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
3V3 U33
TP10
EPM2210F256C5N
TIN
VCCINT<7..0>
VCCIO1<3..0>
VCCIO2<3..0>
VCCIO3<3..0>
VCCIO4<3..0>
DATA_BUS_OUT<7..0>
U33
GCLK H5 IO_H5_GCLK0 EPM2210F256C5N
J5 IO_J5_GCLK1
A J12
H12
IO_J12_GCLK2
DATA_BUS<7..0> 0 P14 R1 33 R151 1
A
IO_H12_GCLK3 IO_P14 IO_R1
M8 IO_M8_DEV_OE 1 R208 0 1 P15 IO_P15 IO_P4 P4 0.1W 2%
RESET M9 IO_M9_DEV_NCLR IO_B16 B16 WATCH_DOG 6 R216 0 2 N13 IO_N13 IO_T2 T2
C13
IN N14 33
IO_C13 4 R214 0 3 IO_N14 IO_P5 P5 R152 4
TDI L6 A15 33 R140 WATCH_DOG_OUT 2 4 M14 R3 2%
TDI IO_A15 R209 0 IO_M14 IO_R3 0.1W
TMS N4 TMS IO_C12 C12 2% 0.1W 0 R207 0 5 N15 IO_N15 IO_N5 N5
TCK P3 TCK IO_B14 B14 3 R213 0 6 M13 IO_M13 IO_R4 R4 33 R153 5
33 1K 2%
TDO R139 M5 TDO IO_D12 D12 R141 0.125W +0.05 0.1W 7 N16 IO_N16 IO_P6 P6 0.1W CHIP_SEL_INV<7..0>
0.1W 2% IO_B13 B13 1% L14 IO_L14 IO_T4 T4
0 D3 IO_D3 IO_C11 C11 M15 IO_M15 IO_N6 N6
1 C2 IO_C2 IO_A13 A13 0 L13 IO_L13 IO_R5 R5
2 C3 IO_C3 IO_D11 D11 M16 IO_M16 IO_M6 M6
3 E3 IO_E3 IO_B12 B12 KEY_MATRIX_IN0 IN 2 L12 IO_L12 IO_T5 T5
4 D2 IO_D2 IO_E11 E11 KEY_MATRIX_IN1 IN L15 IO_L15 IO_P7 P7
5 E4 IO_E4 IO_A12 A12 KEY_MATRIX_IN2 IN 3 L11 IO_L11 IO_R6 R6
CHIP_SEL_CPLD<3..0>
6 D1 IO_D1 IO_C10 C10 KEY_MATRIX_IN3 IN L16 IO_L16 IO_N7 N7 LOGIC0
LED_DRV1<6..0> E5 IO_E5 IO_B11 B11 0 K14 IO_K14 IO_T6 T6 LOGIC1
E2 IO_E2 IO_D10 D10 1 K15 IO_K15 IO_M7 M7 LOGIC2
0 F3 A11 KEY_SEL0 TEST_SWITCH<2..0> 2 K13 R7 LOGIC3
IO_F3 IO_A11 OUT IO_K13 IO_R7
1 E1 IO_E1 IO_E10 E10 KEY_SEL1 K16 IO_K16 IO_P8 P8 LOGIC4
F4 B10 KEY_SEL2 OUT K12 T7
2 IO_F4 IO_B10 OUT 1 IO_K12 IO_T7
3 F2 IO_F2 IO_C9 C9 KEY_SEL3 0 J15 IO_J15 IO_N8 N8 0
F5 A10 OUT J14 R8
4 IO_F5 IO_A10 KEY_SEL4 OUT 1 IO_J14 IO_R8 1
5 F1 IO_F1 IO_D9 D9 2 J16 IO_J16 IO_N9 N9 2
6 F6 IO_F6 IO_B9 B9 3 J13 IO_J13 IO_T8 T8 3
B LED_DRV2<6..0> G2 IO_G2 IO_E9 E9 NOML_LED DS9 3V3 4 H16 IO_H16 IO_T9 T9 4 B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
K1 IO_K1 IO_D7 D7 RS1_CLOCK 33 R142 E16 IO_E16 IO_N11 N11 33 R154 RS2_CLOCK
332 0.1W 2% 0.1W 2%
J3 IO_J3 IO_A5 A5 GREEN F12 IO_F12 IO_R12 R12
0.125W RS1_CS RS2_CS
K2 IO_K2 IO_C7 C7 33 R143 E15 IO_E15 IO_P11 P11 33 R155
DS14 0.1W 2% 0.1W 2%
K5 IO_K5 IO_B5 B5 F13 IO_F13 IO_T13 T13
HSMG-C190 RS1_RESET RS2_RESET
L1 IO_L1 IO_E6 E6 33 R144 D16 IO_D16 IO_M12 M12 33 R156
K4 IO_K4 IO_A4 A4 R194 0.1W 2% F14 IO_F14 IO_R13 R13 0.1W 2%
L2 D6 LOGIC2 1 2 RS1_CH_RD 33 R145 D15 N12 RS2_CH_RD
IO_L2 IO_D6 IO_D15 IO_N12 33 R157
K3 IO_K3 IO_B4 B4 0.1W 2% E12 IO_E12 IO_R14 R14 0.1W 2%
332 RS1_CH_WR 33 RS2_CH_WR
M1 IO_M1 IO_C6 C6 GREEN R146 D14 IO_D14 IO_P12 P12 33 R158
0.125W 0.1W 2% 0.1W 2%
L5 IO_L5 IO_C4 C4 DS15 E13 IO_E13 IO_T15 T15
M2 IO_M2 IO_C5 C5 HSMG-C190 RS1_INT 33 R147 C15 IO_C15 IO_R16 R16 33 R159 RS2_INT
C L4 IO_L4 IO_B3 B3
R195
0.1W 2% C14 IO_C14 IO_P13 P13 0.1W 2% C
L3 IO_L3 IO_D5 D5 LOGIC3 1 2 E14 IO_E14
N1 IO_N1 IO_A2 A2 D13 IO_D13
M4 IO_M4 IO_B1 B1 TP3 332
GREEN SYM 2 OF 2
N2 IO_N2 IO_D4 D4 0.125W
M3 IO_M3 TIN DS16 5 R215 0
N3 IO_N3 GNDINT<7..0> HSMG-C190 +0.05 0.1W
P2 IO_P2 GNDIO<15..0> 7 R217 0
R219
SYM 1 OF 2 LOGIC4 1 2 +0.05 0.1W
332
3V3 GREEN
0.125W
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
0.1U
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
C38
C39
C40
C42
C44
C46
C48
C49
C50
C51
C52
C53
C54
C55
C56
C57
C58
C59
C60
C61
3V3
D D
REV 2 01July04
C125
0.1U
C126
0.1U
C127
0.1U
C128
0.1U
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
16V
10%
C41
10U
C43
10U
C45
10U
C47
10U
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
led_display 5 of 7 5446243SCH 2 7 of 15
1
Approved Document - 5446243SCH_r2.pdf Page 8 of 16
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
3V3
A 3V3 A
0.125W
0.125W
0.125W
Y1 12.288MHZ
R99
R101
R102
R103
4 VCC VOUT 3 GCLK
R97
1 2 33
ENABLE GND 0.1W
1K
1%
1K
1%
1K
1%
1K 2% 3V3
0.125W J2
1% TCK 33 R107
C7
0.1W 2%
1 1 2 2
0.1U
16V
10%
C22
0.1U TDO 3 3 4 4
16V 5 5 6 6
10% 7 7 8 8
TMS 33 R108 9 10
9 10
0.1W 2%
R109 PIN
TDI 33
STRAIGHT
0.125W
0.1W 2% RIBBON_CABLE_LOW_PROFILE
DS8
HSMG-C190
R105
3V3
R206
2 1
1K
1%
B 1K B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
GREEN
0.25W
0.1%
TP1
D3
BAV70LT1 3V3 TIN
VCC
A1 1
See the GEHC Myworkshop System to determine the status of this document.
3 K 3V3
A2 2
R100
70V
R104 R110 R111 R112
VR1 S1 1K 1K 1K 10K
2K 0.125W 0.125W 0.125W
ADP3339-3.3 219-04MST 0.125W
0.125W 1% 1% 1% 1%
1% TEST_SWITCH<2..0>
3 VIN VOUT 2 1 I1 O1 8 0
GND 1 2 I2 O2 7 1
C TP2 C
0.1U
16V
10%
35V
10%
C20
C13
35V
10%
3 I3 O3 6 2
C8
1U
1U
3.3V TIN
4 I4 O4 5 R106 RESET
33
0.1W
2%
C71 C72 C73 C124
0.1U 0.1U 0.1U 10%
50V 50V 50V 25V
10% 10% 10% 10U
3V3
C6 C9 C10 C11 C12 C14 C15 C16 C17 C18 C19 C21 C23 C24 C25 C26 C27 C28 C29 C30
16V
10%
10U
0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U
C5
50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V
10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10%
D D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
led_display 6 of 7 5446243SCH 2 8 of 15
1
Approved Document - 5446243SCH_r2.pdf Page 9 of 16
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
A A
1LD DATA_BUS_SEG1<6..0>
U22 12V HDSP-A901
ULN2803ADW DATA_BUS_SEG1<6..0>
LED_DRV1<6..0> DATA_BUS_SEG1<6..0>
1 A1 A 10 R98 1K 0
0 1 I1 O1 18 0 6 R81 1K 2 F B 9 R170 1K 1 12V
1 2 I2 O2 17 1 5 R82 1K 3 G C 8 R175 1K 2
2 3 I3 O3 16 2 4 R83 1K 4 E DP 7 R94 10K
3 4 I4 O4 15 3 3 R84 1K 5 D A2 6 0.125W 1%
4 5 I5 O5 14 4
5 6 I6 O6 13 5
6 7 I7 O7 12 6 12V GREEN
8 I8 O8 11
10
COMMON
B GND 9 B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
P G12
2LD: SID NO. 10BIT
2LD DATA_BUS_SEG2<6..0>
U20 12V HDSP-A901
ULN2803ADW DATA_BUS_SEG2<6..0>
DATA_BUS_SEG2<6..0>
LED_DRV2<6..0>
1 A1 A 10 R180 1K 0
See the GEHC Myworkshop System to determine the status of this document.
0 1 I1 O1 18 0 1 A1 A 10 R204 1K 0
1 2 I2 O2 17 1 6 R89 1K 2 F B 9 R93 1K 1 12V
2 3 I3 O3 16 2 5 R90 1K 3 G C 8 R205 1K 2
3 4 I4 O4 15 3 4 R91 1K 4 E DP 7 R96 10K
4 5 I5 O5 14 4 3 R92 1K 5 D A2 6 0.125W 1%
5 6 I6 O6 13 5
6 7 I7 O7 12 6 12V
WATCH_DOG_OUT 8 I8 O8 11 WDT_DRV GREEN
10
COMMON
GND 9
P G12
D D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
led_display 7 of 7 5446243SCH 2 9 of 15
1
Approved Document - 5446243SCH_r2.pdf Page 10 of 16
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
KEY_MATRIX_IN_DIFF<7..0>
A 2B1^ IN A
12V
R176 U4
0 DS26LV32AT
R166 3V3
332 1K
R186 R187 R188 R189
0.125W 0.125W 16 10K 10K 10K 10K
R171 VCC
1 1% 1% 0.125W 0.125W 0.125W 0.125W
U6
R177 4 EN ULN2803ADW 1% 1% 1% 1% KEY_MATRIX_SEL<4..0>
2 1K 12 EN_N
0.125W
R167
332 1% 1K 2 3 KEY_MATRIX_IN0 KEY_SEL0 1 18 0
INP<3> O<3> OUT IN I1 O1
0.125W 0.125W 1 KEY_SEL1 2 17 1
R172 INN<3> IN I2 O2
3 1% 1% 6 5 KEY_MATRIX_IN1 KEY_SEL2 3 16 2
INP<2> O<2> OUT IN I3 O3
7 INN<2> IN KEY_SEL3 4 I4 O4 15 3
1K 10 11 KEY_MATRIX_IN2 KEY_SEL4 5 14 4
R178 INP<1> O<1> OUT IN I5 O5
4 0.125W 9 6 13
INN<1> I6 O6
1% 14 13 KEY_MATRIX_IN3 7 12 C66 C67 C68 C69 C70
R168 INP<0> O<0> OUT I7 O7 12V
332 1K 15 8 11
INN<0> I8 O8 10N 10N 10N 10N 10N
0.125W 0.125W 8 10 50V 50V 50V 50V 50V
R173 GND
5 1% 1% 10% 10% 10% 10% 10%
COMMON
R179 GND 9
6 1K
0.125W
R169 P P
332 1% 1K
0.125W G12 G12
0.125W R174
7 1% 1%
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
1K
0.125W
1%
See the GEHC Myworkshop System to determine the status of this document.
12V
VCC
KEY_MATRIX_OUT<3..0> R218 R220 R221 R231 R182 R183 R184 R185 KEY_MATRIX_OUT_OP<3..0>
1K 1K 1K 1K 1K 1K 1K 1K
0.25W 0.25W 0.25W 0.25W U5 0.125W 0.125W 0.125W 0.125W
C 0.1% 0.1% 0.1% 0.1%
TCMT4100 1% 1% 1% 1% C
U7 KEY_MATRIX_OUT_DIFF<7..0>
R162 DS26C31T OUT
1 16 0
U26 2A4^
332 12
74VHC_AHC14 EN_N
0.125W 4 EN
0 R163 2 15
3 14 1 0 1 A<5> B<5> 2 1 I<3> OUTP<3> 2 0
1 3 A<4> B<4> 4 OUTN_N<3> 3 1
332 2 5 6 7 6 2
A<3> B<3> I<2> OUTP<2>
0.125W 3 9 8 5 3
A<2> B<2> OUTN_N<2>
1 R164 4 13 11 A<1> B<1> 10 9 I<1> OUTP<1> 10 4
5 12 2 13 A<0> B<0> 12 OUTN_N<1> 11 5
15 I<0> OUTP<0> 14 6
332 13 7
OUTN_N<0>
0.125W
VCC=VCC;GND=GND
2 R165 6 11
7 10 3 VCC=VCC;GND=GND
332
0.125W
3 8 9 C62 C63 C64 C65
10N 10N 10N 10N
50V 50V 50V 50V
10% 10% 10% 10%
D D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
key_matrix 1 of 3 5446243SCH 2 10 of 15
1
Approved Document - 5446243SCH_r2.pdf Page 11 of 16
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
12V
S2 FL1 D4 KEY_MATRIX_OUT<3..0> 12V
BLM11A102S S7 FL8 KEY_MATRIX_OUT<3..0>
MURS120T3 D10
1 NO rf15 NC 2 1 2 0 BLM11A102S MURS120T3
1 NO rf15 NC 2 1 2 0
4 LED1+ NC 7 1K OHM 200V
4 7 1K OHM
LED1+ NC 200V
F1 6 3 2PSLD
LED2+ LED1- IN 2A1^ COLLIMATOR ADJUST AUTO
RESERVE,NOT WELDING 6 LED2+ LED1- 3 7PSLD IN 2A1^
LED2- 5
LED2- 5
A A
S3 FL2 D5
BLM11A102S MURS120T3
1 NO rf15 NC 2 1 2 1 S8 FL9 D11
BLM11A102S MURS120T3
4 7 1K OHM KEY_MATRIX_SEL<2> 1 2 1 2 1
LED1+ NC 200V NO rf15 NC
BLM11A102S MURS120T3
KEY_MATRIX_SEL<0> 1 2 1 2 3
NO rf15 NC
5 4 7 1K OHM
LED2- LED1+ NC 200V
COLLIMATOR ADJUST MANUAL 6 3 10PSLD
LED2+ LED1- IN 2B1^
See the GEHC Myworkshop System to determine the status of this document.
S6 FL3 D8 LED2- 5
BLM11A102S MURS120T3
KEY_MATRIX_SEL<1> 1 2 1 2 0
NO rf15 NC
4 7 1K OHM
LED1+ NC 200V
F2 6 LED2+ LED1- 3 6PSLD IN 2A1^
RESERVE,NOT WELDING
LED2- 5
C C
S11 FL12 D13
BLM11A102S MURS120T3
1 NO rf15 NC 2 1 2 1
4 7 1K OHM
LED1+ NC 200V
12' INTENSIFIER MODE
6 LED2+ LED1- 3 11PSLD IN
LED2- 5
REV 2 01July04
6' INTENSIFIER MODE 4 7 1K OHM
LED1+ NC 200V
6 LED2+ LED1- 3 13PSLD
IN
LED2- 5 GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
key_matrix 2 of 3 5446243SCH 2 11 of 15
1
Approved Document - 5446243SCH_r2.pdf Page 12 of 16
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
2B1^ IN CONSOLE_POWER
R196
1 16 0
C74
332
0.125W
2B1^ TECH SPOT 10N R197 2 15
IN 50V 3 14 1
C75
332
0.125W
2A1^ 1ST TUBE 10N R198 4 13
IN 50V 5 12 2
C76
332
0.125W
2B1^ X-RAY ON 10N R199 6 11
IN 50V 7 10 3
C77
332
0.125W
R210
2B1^ ABNORMAL 10N 8 9 KEY_MATRIX_SEL<3>
IN 50V
10
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
0.125W
1%
12V
See the GEHC Myworkshop System to determine the status of this document.
R201
1 16 ID NO+ 2A4^
OUT
R212
C 332 1K C
0.125W 0.125W
2 15 Y5 1%
R202
3 14
IN 2B1^
KEY_MATRIX_OUT<2>
332
0.125W
R203 4 13 KEY_MATRIX_SEL<1>
5 12 R211 WATCH_DOG 2A4^
OUT
332 33
0.125W 0.1W
KEY_MATRIX_SEL<4> 6 11 2%
7 10
8 9
D D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
key_matrix 3 of 3 5446243SCH 2 12 of 15
1 2
Approved Document - 5446243SCH_r2.pdf Page 13 of 16
3 4 5 6 7 8
1 2 3 4 5 6 7 8
331CN<49..0> 331CN<49..0>
332CN GROUND 331CN
A GROUND A
KEY_MATRIX_OUT_DIFF<7..0> 1 2 KEY_MATRIX_OUT_DIFF<7..0> 1 2
2C5^ IN 1 2 1 2
1 3 3 4 4 0 2 3 3 4 4 3
3 5 5 6 6 2 4 5 5 6 6 5
5 7 7 8 8 4 6 7 7 8 8 7
KEY_MATRIX_IN_DIFF<7..0> 7 9 10 6 KEY_MATRIX_IN_DIFF<7..0> 8 9 10 9
11
9 10
12 OUT 2C8^ 11
9 10
12
0 11 12 1 10 11 12 11
2 13 13 14 14 3 12 13 13 14 14 13
4 15 15 16 16 5 14 15 15 16 16 15
DATA_LOW_DIFF<7..0> 6 17 18 7 DATA_LOW_DIFF<7..0> 16 17 18 17
0 19
17 18
20 OUT 2C8^ 19
17 18
20
19 20 1 18 19 20 19
2 21 21 22 22 3 20 21 21 22 22 21
4 23 23 24 24 5 22 23 23 24 24 23
DATA_HIGH_DIFF<7..0> 6 25 26 7 DATA_HIGH_DIFF<7..0> 24 25 26 25
27
25 26
28 OUT 2C8^ 27
25 26
28
0 27 28 1 26 27 28 27
2 29 29 30 30 3 28 29 29 30 30 29
4 31 32 5 30 31 32 331CN_32
CHIP_SEL_DIFF<7..0> 31 32 CHIP_SEL_DIFF<7..0> 31 32 OUT 2D8^
6 33 34 7 33 34
35
33 34
36 OUT 2C8^ 35
33 34
36
0 35 36 1 34 35 36 34
2 37 37 38 38 3 36 37 37 38 38 36
4 39 40 5 39 40 OPPRESS_COM
39 40 39 40
6 41 41 42 42 7 P G12 40 41 41 42 42 40
43 43 44 44 43 43 44 44
45 45 46 46 45 45 46 46
47 47 48 48 47 47 48 48
B 49 49 50 50 +12V 49 49 50 50 +12V B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
P G12 P G12
PIN PIN
STRAIGHT STRAIGHT
RIBBON_CABLE_STANDARD RIBBON_CABLE_STANDARD
333CN
See the GEHC Myworkshop System to determine the status of this document.
1 1 2 2
3 4 DS11
3 4
+5V 5 6 +5V HLMP-2755
5 6
7 7 8 8
9 9 10 10 1K 331CN<29>
1 CA AA 2 R241
11 11 12 12 0.1%
13 14 R_POSITION 0.25W
2C5^ IN F_POSITION 13 14 IN 2C5^ 1K 331CN<30>
4 CB AB 3 R242
2C5^ IN F_ON 15 16 R_ON
15 16 IN 2C5^ 0.1% 0.25W
2C5^ IN EMERGENCY 17 17 18 18 ID NO+
IN 2C5^ 1K
R239 5 CC AC 6
2D8^ OUT Y5 19 20 Y6
21
CONSOLE_POWER
19 20
22
CONSOLE_POWER OUT 2D8^ 0.1% 0.25W
C 21 22 OUT 2C8^ OPPRESS_COM R240 1K 8 7 C
2C8^ OUT TECH SPOT 23 23 24 24 1ST TUBE 2C8^ 0.1% CD AD
X-RAY ON 25 26 ABNORMAL OUT 0.25W
2D8^ OUT 25 26 OUT 2C8^
20 27 27 28 28 19
22 29 30 21 YELLOW
29 30
331CN<49..0> 31 31 32 32 331CN<49..0>
33 33 34 34
35 35 36 36
37 37 38 38
39 39 40 40
41 41 42 42
P G12 43 43 44 44 P G12 +5V +12V
45 45 46 46
47 47 48 48
+12V 49 49 50 50 +12V
C78 C79 C80 C81 C82 C83 C84 C85 C86 C87 C88
0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U
50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V
PIN 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10%
STRAIGHT
RIBBON_CABLE_STANDARD
P G12
D D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
connector 1 of 3 5446243SCH 2 13 of 15
1
Approved Document - 5446243SCH_r2.pdf Page 14 of 16
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
COLLIMATOR_LIGHT_POS 1 1 PIN
1 1 2 2 PIN1: GND 7 1 1 PIN 16 1 1 PIN
STRAIGHT COLLIMATOR_LIGHT_NEG 2 2 STRAIGHT
2 3 3 4 4 3 PIN2: JOYSTICK_UP 9 2 2 STRAIGHT 17 2 2
WIRE_TO_BOARD 3 3 WIRE_TO_BOARD
4 5 5 6 6 5 PIN3: JOYSTICK_DOWN 8 3 3 WIRE_TO_BOARD 3 3 4 4
6 7 7 8 8 4 4 4 4
9 9 10 10
11 11 12 12
13 13 14 14 13
A 14 15 15 16 16 15 A
17 17 18 18 338CN 335CN RADIOGRAPHY EM_STOP_CN
19 19 20 20
21 21 22 22 PIN PIN
PIN1: JOYSTICK_LEFT 11 1 1 18 1 1
23 23 24 24 23 STRAIGHT STRAIGHT CONSOLE_EM_SW_OUTPUT 331CN<40> 1 1
PIN2: JOYSTICK_RIGHT 12 2 2 17 2 2
24 25 25 26 26 25 WIRE_TO_BOARD WIRE_TO_BOARD +24V FROM TABLE 331CN<36> 2 2
PIN3: GND 10 3 3 3 3
26 27 27 28 28 27 +24V FROM TABLE 331CN<36> 3 3
4 4 4 4
28 29 29 30 30 21 PIN30: GND CONSOLE_EM_SW_LED 331CN<34> 4 4
31 31 32 32 19 PIN32: SID_1050M
33 33 34 34 21 PIN34: GND
35 35 36 36 20 PIN36: SID_1200M PIN
46 37 37 38 38 21 PIN38: GND STRAIGHT
39 39 40 40 22 PIN40: SID_1500M WIRE_TO_BOARD
PIN
STRAIGHT
RIBBON_CABLE_STANDARD
S14
331CN<24> 6 6 COLLIMATOR_LIGHT_NEG 6 6 6 6
331CN<25> 1 1
CR5
331CN<26> 3 3 SMS24C
331CN<27> 4 4 2 2
D 331CN<28> 5 5
D
GROUND
REV 2 01July04
6 6
26.7V GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
connector 2 of 3 5446243SCH 2 14 of 15
1
Approved Document - 5446243SCH_r2.pdf Page 15 of 16
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
FL11
NFM41PC155B1E3
USE PACKAGE OF 2378407-4,THE BOM PN.IS 5482604
TP8
VCC
VCC
+5V
A 1 3 TIN A
1.5UF
C89 C91 C94 C97 C100 C103 C106 C109 C113 C115 C117
4
100U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U
1
TP9 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V
20% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10%
TIN
CR1
GBLC05C
2 5V_STAND_OFF DS12
RESERVE,NOT WELDING VCC HSMG-C190
R243
2 1
GROUND 1K
GREEN
0.25W
0.1%
FL10
NFM41PC155B1E3
USE PACKAGE OF 2378407-4,THE BOM PN.IS 5482604
12V
B B
State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.
+12V DS13
1 3 HSMG-C190
12V
R244
1.5UF 2 1
2
1K
GREEN
0.25W P G12
1
0.1%
P G12
See the GEHC Myworkshop System to determine the status of this document.
RESERVE,NOT WELDING
C90 C92 C95 C98 C101 C104 C107 C110 C112 C114 C116 C118 C119 C120 C121
100U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U
C GROUND TP5 TP7 50V
20%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
50V
10%
C
TIN TIN
P G12
R193 0
+0.05 1W
12V
GROUND
PIN
STRAIGHT
MH12 TAB P G12
D GROUND MHP4_00TB10_00
GROUND D
REV 2 01July04
GE Healthcare
B Size
Company Restricted
Block Path Block Sheet Dwg No Rev Sheet
connector 3 of 3 5446243SCH 2 15 of 15
1
Approved Document - 5446243SCH_r2.pdf Page 16 of 16
2 3 4 5 6 7 8
Section 1.0
Scope
This section provides detailed information about each MIS run in the form of individual MIS cable
charts.
Each of the following charts defines a single interconnection in the system. The charts are arranged
in the order, according to MIS numbers. In some cases, a particular MIS number is repeated, except
for a letter added at the end. Such a set of charts use the same cable, and carry essentially the
same signals, however the applications for each chart is different - the point of connection is
different (at one or both ends) for each chart in the set.
Section 2.0
How to Use
Each MIS cable shown on the MIS map has its own MIS chart. Each chart identifies all signals
present on the cable, and the specific pins associated with each signal. See Figure 11-254 for an
example.
Section 3.0
MIS Charts
3.1 System Main Input Power Cable
Note: The four cables should be provided by hospital, three are power supply cables, and the other one
is ground cable.
TB1
1 CONSOLE_EM_SW_OUTPUT 1 Black
2 +24V FROM TABLE 2 Red
3 +24V FROM TABLE X1 Green
4 CONSOLE_EM_SW_LED X2 White
GND GND
1 GND 2 White
2 +12V 1 Black
GND GND
GND GND
Table Horizontal
TDSP Board 337CN Table Top Front/Back Motion Joystick
1 GND 1 Red
2 JOYSTICK_UP 2 Black
3 JOYSTICK_DOWN 3 White
2 RS-TXD 2 Red
3 RS_RXD 3 Green
5 GND 5 Black
3.9 5440284, Console Digital box Image Converter BNC Signal Cable
2 Core 1
1 Shell 2
Desk-E Console-E1
GND GND
GND GND
2 TXD 2
3 RXD 3
5 GND 5
1 1
4 4
6 6
7 7
8 8
9 9
GND GND
GND GND
1 1 Brown
14 14 Brown/White
2 2 Red
15 15 Red/Black
3 3 Orange
16 16 Orange/Black
4 4 Yellow
17 17 Yellow/Black
5 5 Green
18 18 Green/Black
6 6 Blue
19 19 Blue/White
7 7 Purple
20 20 Purple/White
8 8 Gray
21 21 Gray/Black
9 9 White
22 22 White/Black
10 10 Pink
23 23 Pink/Black
11 11 Light Blue
24 24 Light Blue/Black
12 12 Light Blue Yellow
25 25 Light Blue Green
13 13 Pink Yellow
26 26 Pink White
2 TXD 3 Red
3 RXD 2 Black
5 GND 5 White
1 +5V 1 White
2 +5V 2 Blue
3 +5V 3 White
4 +5V 4 Orange
5 +5V 5 White
6 +5V 6 Green
7 GND 7 White
8 GND 8 Brown
9 GND 9 White
10 GND 10 Gray
11 GND 11 Red
12 GND 12 Blue
13 F_POSITION 13 Red
14 R_POSITION 14 Orange
15 F_ON 15 Red
16 R_ON 16 Green
17 EMERGENCY 17 Red
18 ID NO+ 18 Brown
19 Y5 19 Red
20 Y6 20 Gray
21 CONSOLE_POWER 21 Black
22 CONSOLE_POWER 22 Blue
23 TECH SPOT 23 Black
24 1ST TUBE 24 Orange
GND GND
Monitor Console-E
GND GND
GND GND
TM1 PS1/PS2
TM1 Monitor
TM1-2 L Brown
TM1-5 N Blue
TM1-7 E Yel/Grn
23 VID0+ 1 Brown
4 VID0- 26 Brown/White
3 VID1+ 2 Red
22 VID1- 27 Red/White
21 VID2+ 3 Orange
2 VID2- 28 Orange/White
1 VID3+ 4 Yellow
10 VID3- 29 Yellow/White
28 VID4+ 5 Green
9 VID4- 30 Green/White
8 VID5+ 6 Blue
27 VID5- 31 Blue/White
26 VID6+ 7 Purple
7 VID6- 32 Purple/White
5 VID7+ 8 Gray
25 VID7- 33 Gray/White
33 VID8+ 9 Black
14 VID8- 34 Black/White
13 VID9+ 10 Pink
32 VID9- 35 Pink/White
30 VID10+ 11 Light Green
11 VID10- 36 Light Green/White
10 VID11+ 12 Light Blue
29 VID11- 37 Light Blue/White
17 FRAME_VALID+ 15 Red/Blue
36 FRAME_VALID- 40 Red/Orange
35 DATA_VALID+ 17 Orange/Black
16 DATA_VALID- 42 Orange/Green
37 LINE_VALID+ 16 Green/Black
19 LINE_VALID- 41 Green/Orange
1 RAD_STATUS 1 Black
2 FLUORO_STATUS 20 Black/White
3 SINGLE_SPOT 2 Brown
4 GATE_TRIGGER 21 Brown/White
5 GATE_SELECT 3 Red
6 DSA_SELECT 22 Red/White
7 PATH_SELECT 4 Orange
8 REPLAY_SELECT 23 Orange/White
14 SINGLE_FRM_FORWARD 5 Red
15 SINGLE_FRM_BACKWARD 24 Red/Black
16 WW_INCREASE 6 Green
17 WW_DECREASE 25 Green/White
18 WL_INCREASE 7 Blue
19 WL_DECREASE 26 Blue/White
20 reserved 8 Violet
21 reserved 27 Violet/White
12 9 Gray
TM1 Chamber
TM1-3 L Brown
TM1-6 N Blue
TM1-9 E Yel/Grn
2 RXD 3 Black
3 TXD 2 Brown
5 GND 5 Red
1 1 Yellow
4 4 Green
6 6 Blue
7 7 Violet
8 8 Gray
9 9 White
1 MEM_CMD_2 1 Black
2 reserved 2 Brown
3 reserved 3 Red
4 MEM_CMD_1 4 Orange
5 GND 5 Yellow
6 SHAD_CMD_1 6 Green
7 MEM_CMD_3 7 Blue
8 BLK_CMD 8 Purple
9 RF_CMD_1 9 Gray
10 GND 10 White
11 SHAD_CMD_0 11 Light Green
12 MEM_CMD_4 12 Light Blue
13 RF_CMD_2 13 Pink
14 RF_CMD_0 14 Peach Pink
15 GND 15 Light Gray
16 EE_CMD_0 16 Black/White
17 VI_CMD 17 Brown/White
18 GAMMA_CMD_1 18 Red/White
19 LIM_CMD 19 Orange/White
20 GND 20 Yellow/White
21 reserved 21 Green/White
22 MEM_CMD_0 22 Blue/White
23 MEM_CMD_5 23 Purple/White
24 reserved 24 Gray/White
25 GND 25 Light Blue/White
26 MEM_CMD_6 26 Peach Pink/White
27 MODE_CMD_1 27 Light Gray/White
28 MODE_CMD_2 28 Dark Green
29 MODE_CMD_3 29 Brown/Black
30 GND 30 Red/Black
31 GAMMA_CMD_2 31 Orange/Black
32 MODE_CMD_0 32 Yellow/Black
33 TXT_CMD 33 Green/Black
34 HI_CMD 34 Blue/Black
35 GND 35 Gray/Black
36 GAMMA_CMD_0 36 White/Black
37 EE_CMD_1 37 Light Blue/Black
PCU Console-E2
GND GND
Table Horizontal
TDSP Board 338CN Collumn UP/Down Motion Joystick
1 JOYSTICK_LEFT 1 White
2 JOYSTICK_RIGHT 2 Black
3 GND 3 Red
Table Horizontal
TDSP Board 335CN Exposure switch Motion Joystick
1 Exposure_P 1 White
2 Exposure_N 2 Black
3 2 Black
4 1 Red
1 COLLIMATOR_LIGHT_POS 1 White
2 COLLIMATOR_LIGHT_NEG 2 Black
TM1 Workstation
TM1-3 L Brown
TM1-6 N Blue
TM1-8 E Yellow/Green
1 B-C White
2 B-No Black
1 Foot Switch_P 1
2 Foot Switch_N 2
3 3
4 4
Table PDU
TM1 J3
Table Connector
1 COLLIMATOR_LIGHT_POS 1 Black
2 COLLIMATOR_LIGHT_NEG 2 White
1 GND 1 Black 1
4 GND 4 Red
5 GND 5 Black 2
6 II_CTRL<1> 6 White
7 GND 7 Black 3
8 GND 8 Green
13 II_CTRL<2> 13 Black 4
14 II_CTRL<0> 14 Blue
15 24V 15 Green/Black
TB2.W GEN-C
1 L White
2 N Black
3 E Green
Table-E PDU-E
GND GND
1 24VDC 1 Black
2 0V 2 White
3 E 3
TB2.E GEN-E
Ground Ground
TB2.U GEN-A
1 Ground 1 White
2 Ground 2 Blue
3 KEY_MATRIX_OUT_DIFF<7..0> 3 White
4 KEY_MATRIX_OUT_DIFF<7..0> 4 Orange
5 KEY_MATRIX_OUT_DIFF<7..0> 5 White
6 KEY_MATRIX_OUT_DIFF<7..0> 6 Green
7 KEY_MATRIX_OUT_DIFF<7..0> 7 White
8 KEY_MATRIX_OUT_DIFF<7..0> 8 Brown
9 KEY_MATRIX_OUT_DIFF<7..0> 9 White
10 KEY_MATRIX_OUT_DIFF<7..0> 10 Gray
11 KEY_MATRIX_IN_DIFF<7..0> 11 Red
12 KEY_MATRIX_IN_DIFF<7..0> 12 Blue
13 KEY_MATRIX_IN_DIFF<7..0> 13 Red
Table GEN
1 T1 White
2 T2 Black
3 T3 Red
4 T4 Brown
5 T5 Orange
J4 220VAC Power
1 220V T1 Red
2 0V T2 Blue
CN93 J5
1 220VAC 1 Red
2 0VAC 2 Blue
8 Signal 1
2 Shield 2
PDU-E Console-E
Ground Ground
Console GEN
1 DIG_FLUORO_ON_P 1 White
14 DIG_FLUORO_ON_N 2 Blue
2 DIG_RAD_PREP_P 3 White
15 DIG_RAD_PREP_N 4 Orange
3 DIG_RAD_READY_P 5 White
16 DIG_RAD_READY_N 6 Green
4 DIG_MODE_SEL_P 7 White
17 DIG_MODE_SEL_N 8 Brown
5 DIG_II_MODE1_P 9 White
18 DIG_II_MODE1_N 10 Gray
6 DIG_II_MODE2_P 11 Red
19 DIG_II_MODE2_N 12 Blue
7 DIG_RAD_EXP_P 13 Red
20 DIG_RAD_EXP_N 14 Orange
8 DIG_II_MODE3_P 15 Red
21 DIG_II_MODE3_N 16 Green
10 DIG_PULSE_FLUORO_ON_P 17 Red
23 DIG_PULSE_FLUORO_ON_N 18 Brown
11 DIG_XRAY_ON_P 19 Red
24 DIG_XRAY_ON_N 20 Gray
12 DIG_PULSE_FLUORO_SYNC_P 21 Black
25 DIG_PULSE_FLUORO_SYNC_N 22 Blue
Table GEN
1 1
5 1
2 2
6 2
Table GEN
GND GND
1 1 Red
6 6
2 2 Gray
7 7
3 3 Blue
8 8
10 10 Yellow
13 13 Black
14 14 Orange
1 P_GND 1 Violet
2 P_GND 2 Grey
3 GND 3 Violet
4 TILT_RISE_CONSOLE_SW 4 Brown
5 SPARE_CONSOLE_SW 5 Violet
6 TILT_FALL_CONSOLE_SW 6 Green
7 TILT_FALLINV_CONSOLE_SW 7 Violet
8 GND 8 Orange
9 TOP_LEFT_CONSOLE_SW 9 Violet
10 TOP_RIGHT_CONSOLE_SW 10 Blue
11 GND 11 Yellow
12 TUBE_DOWN_CONSOLE_SW 12 Gray
13 TUBE_UP_CONSOLE_SW 13 Yellow
14 GND 14 Brown
15 COM_UP_CONSOLE_SW 15 Yellow
16 COM_DOWN_CONSOLE_SW 16 Green
17 FOOT_CONSOLE_SW 17 Yellow
18 GND 18 Orange
19 XRAY_CONSOLE_SW 19 Yellow
20 SID_DOWN_CONSOLE_SW 20 Blue
21 SID_MID_CONSOLE_SW 21 Black
22 GND 22 Gray
23 SID_UP_CONSOLE_SW 23 Black
24 CON_RES_TEMP- 24 Brown
25 CON1_LR_TEMP 25 Black
26 CON_RES_LR_TEMP+ 26 Green
27 CON_RES_TEMP- 27 Black
28 CON1_UD_TEMP 28 Orange
29 CON_RES_UD_TEMP+ 29 Black
30 24V 30 Blue
31 24V 31 Red
32 32 Gray
33 33 Red
34 34 Brown
35 EMERGENCY_LED 35 Red
36 EMERGENCY_LED 36 Green
37 24V 37 Red
38 24V 38 Orange
39 COM_LED 39 Red
40 40 Bl
Page 516 Chapter 11 - MIS Chart
GE HEALTHCARE GE EXCLUSIVE USE ONLY
DIRECTION 5478064-1EN, REVISION 7 PRECISION THUNIS-800+ SERVICE MANUAL
40 COM_LED 40 Blue
41 CONSOLE_EM_SW 41 White
42 CONSOLE_EM_SW 42 Gray
43 43 White
44 44 Brown
45 45 White
46 46 Green
47 +12V_GND 47 White
48 +12V_GND 48 Orange
49 +12V 49 White
50 +12V 50 Blue
Table Connector
3 422_T+ 3 Black
4 422_T- 4 Black/White
5 422_R+ 5 Brown
6 422_R- 6 Brown/White
Console GEN-Room
1 REMOTE_PREP_P 1 White
14 REMOTE_PREP_N 2 Blue
2 REMOTE_FLUORO_P 3 White
15 REMOTE_FLUORO_N 4 Orange
3 REMOTE_EXP_P 5 White
16 REMOTE_EXP_N 6 Green
4 MULTISPOT_P 7 White
17 MULTISPOT_N 8 Brown
6 XRAY_ON_P 9 White
19 XRAY_ON_N 10 Gray
7 SPARE_INPUT1_P 11 Red
20 SPARE_INPUT1_N 12 Blue
8 SPARE_INPUT2_P 13 Red
21 SPARE_INPUT2_N 14 Orange
9 SPARE_INPUT3_P 15 Red
22 SPARE_INPUT3_N 16 Green
10 SPARE_INPUT4_P 17 Red
23 SPARE_INPUT4_N 18 Brown
1 GND 1 Black
2 LEFT_LIMIT_SW 2 Brown
3 GND 3 Red
4 RIGHT_LIMIT_SW 4 Orange
5 GND 5 Yellow
6 UP_LIMIT_SW 6 Green
7 GND 7 Blue
8 DOWN_LIMIT_SW 8 Violet
9 GND 9 Gray
10 UD_RANGE_STOP 10 White
5 422_T+ 3 Black
6 422_T- 4 Black/White
3 422_R+ 5 Brown
4 422_R- 6 Brown/White
Key BD J2 EM BUTTON
1 CONSOLE_EM_SW 1 Red
2 TABLE_EM_SW 2 Black
3 VCC 24V X1 White
4 EMERGENCY_LED X2 Green
GND
1 1
TM11 13LS
1 P_GND 1 Violet
2 P_GND 2 Grey
3 GND 3 Violet
4 TILT_RISE_CONSOLE_SW 4 Brown
5 SPARE_CONSOLE_SW 5 Violet
6 TILT_FALL_CONSOLE_SW 6 Green
7 TILT_FALLINV_CONSOLE_SW 7 Violet
8 GND 8 Orange
9 TOP_LEFT_CONSOLE_SW 9 Violet
10 TOP_RIGHT_CONSOLE_SW 10 Blue
11 GND 11 Yellow
12 TUBE_DOWN_CONSOLE_SW 12 Gray
13 TUBE_UP_CONSOLE_SW 13 Yellow
14 GND 14 Brown
15 COM_UP_CONSOLE_SW 15 Yellow
16 COM_DOWN_CONSOLE_SW 16 Green
17 FOOT_CONSOLE_SW 17 Yellow
18 GND 18 Orange
19 XRAY_CONSOLE_SW 19 Yellow
20 SID_DOWN_CONSOLE_SW 20 Blue
21 SID_MID_CONSOLE_SW 21 Black
22 GND 22 Gray
23 SID_UP_CONSOLE_SW 23 Black
24 CON_RES_TEMP- 24 Brown
25 CON1_LR_TEMP 25 Black
26 CON_RES_LR_TEMP+ 26 Green
27 CON_RES_TEMP- 27 Black
28 CON1_UD_TEMP 28 Orange
29 CON_RES_UD_TEMP+ 29 Black
30 24V 30 Blue
31 24V 31 Red
32 32 Gray
33 33 Red
34 34 Brown
35 EMERGENCY_LED 35 Red
36 EMERGENCY_LED 36 Green
37 24V 37 Red
38 24V 38 Orange
39 COM LED 39 Red
g
39 COM_LED 39 Red
40 COM_LED 40 Blue
41 CONSOLE_EM_SW 41 White
42 CONSOLE_EM_SW 42 Gray
43 43 White
44 44 Brown
45 45 White
46 46 Green
47 +12V_GND 47 White
48 +12V_GND 48 Orange
49 +12V 49 White
50 +12V 50 Blue
FUSE TM1
1 220Vac RY1-5 Red
2 110Vac F4-2 White
3 0Vac TM1-6 Black
1 G24 1 White
2 CASSTTE_IN_SW 2 Black
1 GND 1 Black
2 Tube_inverter_DO 2 Brown
3 Tube_inverter_DI0 3 Red
4 Tube_inverter_DI1 4 Orange
5 Tube_inverter_DI2 5 Yellow
6 Tube_inverter_+24V 6 Green
7 Tube_inverter_G24 7 Blue
8 8 Pink
9 9 Grey
10 10 White
GND
1 1
1 1 Violet
2 2 Grey
3 REC_DA<1> 3 Violet
4 REC_DA<0> 4 Brown
5 REC_DA<3> 5 Violet
6 REC_DA<2> 6 Green
7 REC_DA<5> 7 Violet
8 REC_DA<4> 8 Orange
9 REC_DA<7> 9 Violet
10 REC_DA<6> 10 Blue
11 TRA_DA<0> 11 Yellow
12 TRA_DA<1> 12 Gray
13 TRA_DA<2> 13 Yellow
14 TRA_DA<3> 14 Brown
15 TRA_DA<4> 15 Yellow
16 TRA_DA<5> 16 Green
17 TRA_DA<6> 17 Yellow
18 TRA_DA<7> 18 Orange
19 TRA_DA<8> 19 Yellow
20 TRA_DA<9> 20 Blue
21 TRA_DA<10> 21 Black
22 TRA_DA<11> 22 Gray
23 TRA_DA<12> 23 Black
24 TRA_DA<13> 24 Brown
25 TRA_DA<14> 25 Black
26 TRA DA<15> 26 Green
27 TRA_DA<16> 27 Black
28 TRA_DA<17> 28 Orange
29 TRA_DA<18> 29 Black
30 TRA_DA<19> 30 Blue
31 TRA_DA<20> 31 Red
32 TRA_DA<21> 32 Gray
33 TRA_DA<22> 33 Red
34 TRA_DA<23> 34 Brown
35 TRA_DA<24> 35 Red
36 TRA_DA<25> 36 Green
37 TRA_DA<26> 37 Red
38 TRA_DA<27> 38 Orange
39 TRA_DA<28> 39 Red
40 TRA_DA<29> 40 Blue
41 TRA_DA<30> 41 White
42 TRA_DA<31> 42 Gray
43 43 White
44 44 Brown
45 45 White
46 46 Green
47 47 White
48 48 Orange
49 49 White
50 50 Blue
Collimator Tube
GND
1 1
1 POWER_RELAY+ A1 White
2 GND A2 Black
GND
1 1
TM11 11LS
5 GND White/11LS-COM
6 UP_LIMIT_SW Black/11LS-NC
Motor Board J8 A2 P2
1 24VGnd 1 Black
2 24Vdc 2 Red
3 48V DC 1 Black 1
4 48V GND 2 Black 2
1 A2-E13 3 Yellow/Green
1 GND 1 Red
2 CASSTTE_IN_SW 2 Black
3 GND 3 White
Frequency Inverter
FC2 UVW Column UD Motor
1 U 1
2 V 2
3 W 3
4 PE 4
1 GND 1 Black 1
2 2 Black 2
3 3 Brown 1
4 GND 4 Brown 2
5 GND 5 Red 1
6 II_CTRL<1> 6 Red 2
7 GND 7 Orange 1
8 GND 8 Orange 2
9 9 Yellow 1
10 10 Yellow 2
11 11 Green 1
12 12 Green 2
13 II_CTRL<2> 13 Blue 1
14 II_CTRL<0> 14 Blue 2
15 24V 15 Violet 1
1 U 1 White
2 V 2 Black
3 W 3 Red
4 PE 4 Yellow/Green
DC Motor Driver J2 A6 M5
3 2 Black
4 1 Red
1 GND 1
1 VCC_24V 1 Black
2 VCC_24V 2 Brown
3 ANGLE_LCD_BUSY 3 Red
4 ANGLE_LCD_TXD 4 Orange
5 ANGLE_LCD_RXD 5 Yellow
6 ANGLE_LCD_RXD 6 Green
7 G24 7 Blue
8 G24 8 Purple
3.93 5450221, Table column SID and Compressor Limit Switch Cable 1
44CN-2 41LS/43LS/46LS
1 GND 41LS-COM
2 COMPRESS_UP_STOP 41LS-NC
5 GND 43LS-COM
6 SID_DOWN_STOP 43LS-NC
11 GND 46LS-COM
12 SID_UP_STOP 46LS-NC
1 24V 1 Black
3 24V 3 Black/White
2 24V 2 Brown
4 24V 4 Brown/Black
5 GND 5 Red
6 GND 6 Red/White
7 GND 7 Orange
8 GND 8 Orange/Black
9 9 Yellow
10 LAMP_SIDE 10 Yellow/Black
11 TILT_RISE_SIDE_SW 11 Green
12 TILT_FALL_SIDE_SW 12 Green/Black
13 TUBE_UP_SIDE_SW 13 Blue
14 TUBE_DOWN_SIDE_SW 14 Blue/Black
15 TOP_RIGHT_SIDE_SW 15 Purple
16 TOP_LEFT_SIDE_SW 16 Purple/Black
17 SID_UP_SIDE_SW 17 Gray
18 SID_MID_SIDE_SW 18 Gray/Black
19 SID_DOWN_SIDE_SW 19 White
21 EMERGENCY_LED 21 White/Black
20 TABLE_EM_SW 20 Brown/White
22 CONSOLE_EM_SW 22 Orange/White
23 23 Green/White
24 ANGLE_LCD_BUSY 24 Blue/White
25 ANGLE_LCD_RXD 25 Purple/White
26 ANGLE_LCD_TXD 26 Yellw/White
GND
1 1
GND
1 1
1 G24 1 Black 1
2 COMPRESS_UP_Stop 2 Red
3 G24 3 Black 2
4 COMPRESS_UP_Over 4 White
5 G24 5 Black 3
6 SID_DOWN_STOP 6 Green
7 G24 7 Black 4
8 SID_DOWN_OVER 8 Blue
9 G24 9 Black 5
10 SID_MIDDLE_STOP 10 Brown
11 G24 11 Black 6
12 SID_UP_STOP 12 Yellow
13 G24 13 Black 7
14 SID_UP_OVER 14 Orange
TM11 21LS/22LS
1 GND White/21LS-COM
2 LEFT_LIMIT_SW Black/21LS-NO
3 GND White/22LS-COM
4 RIGHT_LIMIT_SW Black/22LS-NO
1 SID_H 1 Red
2 SID_M 2 Black
3 GND 3 White
1 GND 1
2 Tilt_inverter_DO 2
3 Tilt_inverter_DI0 3
4 Tilt_inverter_DI1 4
5 Tilt_inverter_DI2 5
6 Tilt_inverter_+24V 6
7 Tilt_inverter_G24 7
8 8
9 9
10 10
TM12 TM12
3 7
1 110Vac 1 Red
2 Compress_motor1- 2 Black
3 Compress_motor2- 3 White
Transformer Collimator
1 12Vac L White
2 0Vac N Black
GND
1 1
TM11 12LS
7 GND White/12LS-COM
8 DOWN_LIMIT_SW Black/12LS-NC
Table Board
1 24V CN81-1, 2, 3 Black
2 G24V CN81-4, 5, 6 Gray
3 GND CN51-5, 6, 7, 8 White
4 VCC CN51-1, 2, 3, 4 Red
X-Ray Board
1 12V CN61-1, Intercom J1-1 White
1 GND Brown/1LS-COM
2 VERTICAL_STOP_SW Gray/1LS-NC
3 GND Yellow/2LS-COM
4 LEVEL_CW_STOP White/2LS-NC
5 GND Blue/3LS-COM
6 INCLINE_STOP_SW Red/3LS-NC
Tower A6 A2-E9
GND
1 1
GND
1 1
TM3 CN94-1
110VAC
TM3-1 1 Red
COMPRESS_MOTOR1-
TM3-5 2 Black
COMPRESS_MOTOR2-
TM3-3 3 White
Table Board
1 24V CN81-1, 2, 3 Black
2 G24V CN81-4, 5, 6 Gray
3 GND CN51-5, 6, 7, 8 White
4 VCC CN51-1, 2, 3, 4 Red
X-Ray Board
1 12V CN61-1, Intercom J1-1 White
2, 3 G12V CN61-2, Intercom J1-2 Brown
4 -12V CN61-3 Yellow/Green
GND
1 1
1 DI_FROM_CONSOLE<0> 1
3 DI_FROM_CONSOLE<1> 3
2 DI_FROM_CONSOLE<2> 2
4 DI_FROM_CONSOLE<3> 4
5 DI_FROM_CONSOLE<4> 5
6 DI_FROM_CONSOLE<5> 6
7 DI_FROM_CONSOLE<6> 7
8 DI_FROM_CONSOLE<7> 8
9 DO-TO_CONSOLE<0> 9
10 DO-TO_CONSOLE<1> 10
11 DO-TO_CONSOLE<2> 11
12 DO-TO_CONSOLE<3> 12
13 DO-TO_CONSOLE<4> 13
14 DO-TO_CONSOLE<5> 14
15 DO-TO_CONSOLE<6> 15
16 DO-TO_CONSOLE<7> 16
17 DO-TO_CONSOLE<8> 17
18 DO-TO_CONSOLE<9> 18
19 DO-TO_CONSOLE<10> 19
21 DO-TO_CONSOLE<11> 21
20 DO-TO_CONSOLE<12> 20
22 DO-TO_CONSOLE<13> 22
23 DO-TO_CONSOLE<14> 23
24 DO-TO_CONSOLE<15> 24
25 COL-CPLD<0> 25
26 COL-CPLD<1> 26
CO C
27 COL-CPLD<2> 27
28 COL-CPLD<3> 28
29 COL-CPLD<4> 29
30 COL-CPLD<5> 30
31 COL-CPLD<6> 31
32 COL-CPLD<7> 32
33 DA_SYNC_N 33
34 DA_SCLK 34
35 DA_DIN 35
36 DA_LDAC_N 36
37 CON1_LR 37
38 CON1_UD 38
39 COL_LR_AD 39
40 COL_UD_AD 40
41 COL_FED_LR_AD 41
42 COL_FED_UD_AD 42
43 VCC 43
44 VCC 44
45 VCC 45
46 VCC 46
47 GND 47
48 GND 48
49 GND 49
50 GND 50
TM12 A3 M3
1 1 Gray
2 2 Gray
3 3 Yellow/Green
3 Shield_Gnd 1
2 TUBE_UNLOCK_SW1/2 2
1 Gnd 3
GND
1 1
1 SID_H 1 White
2 SID_M 2 Black
3 GND 3 Red
1 24V 1 Black
3 24V 3 Black/White
2 24V 2 Brown
4 24V 4 Brown/Black
5 GND 5 Red
6 GND 6 Red/White
7 GND 7 Orange
8 GND 8 Orange/Black
9 9 Yellow
10 LAMP_SIDE 10 Yellow/Black
11 TILT_RISE_SIDE_SW 11 Green
12 TILT_FALL_SIDE_SW 12 Green/Black
13 TUBE_UP_SIDE_SW 13 Blue
14 TUBE_DOWN_SIDE_SW 14 Blue/Black
15 TOP_RIGHT_SIDE_SW 15 Purple
16 TOP_LEFT_SIDE_SW 16 Purple/Black
17 SID_UP_SIDE_SW 17 Gray
18 SID_MID_SIDE_SW 18 Gray/Black
19 SID_DOWN_SIDE_SW 19 White
21 EMERGENCY_LED 21 White/Black
20 TABLE_EM_SW 20 Brown/White
22 CONSOLE_EM_SW 22 Orange/White
23 23 Green/White
24 ANGLE_LCD_BUSY 24 Blue/White
25 ANGLE_LCD_RXD 25 Purple/White
26 ANGLE_LCD_TXD 26 Yellw/White
GND
1 1
1 GND 2 White
2 24V dc 1 Black
1 P_GND 1 Violet
2 P_GND 2 Grey
3 GND 3 Violet
4 TILT_RISE_SIDE_SW 4 Brown
5 5 Violet
6 TILT_FALL_SIDE_SW 6 Green
7 7 Violet
8 GND 8 Orange
9 TUBE_DOWN_SIDE_SW 9 Violet
10 TUBE_UP_SIDE_SW 10 Blue
11 GND 11 Yellow
12 TOP_LEFT_SIDE_SW 12 Gray
13 TOP_RIGHT_SIDE_SW 13 Yellow
14 GND 14 Brown
15 COM_UP_IRC_SW 15 Yellow
_ _ _
16 COM_DOWN_IRC_SW 16 Green
17 FOOT_IRC_SW 17 Yellow
18 GND 18 Orange
19 XRAY_IRC_SW 19 Yellow
20 SID_UP_SIDE_SW 20 Blue
21 SID_DOWN_SIDE_SW 21 Black
22 GND 22 Gray
23 SID_MID_SIDE_SW 23 Black
24 CON_RES_TEMPP_ 24 Brown
25 CON1_LR_TEMP 25 Black
26 CON_RES_LR_TEMP+ 26 Green
27 CON_RES_TEMP- 27 Black
28 CON1_UD_TEMP 28 Orange
29 CON_RES_UD_TEMP+ 29 Black
30 24V 30 Blue
31 24V 31 Red
32 32 Gray
33 33 Red
34 34 Brown
35 EMERGENCY_LED 35 Red
36 EMERGENCY_LED 36 Green
37 24V 37 Red
38 24V 38 Orange
39 COM_LED 39 Red
40 COM_LED 40 Blue
41 CONSOLE_EM_SW 41 White
42 CONSOLE_EM_SW 42 Gray
43 43 White
44 44 Brown
45 45 White
46 46 Green
47 +12V_GND 47 White
48 +12V_GND 48 Orange
49 +12V 49 White
50 +12V 50 Blue
TM1 A2 FUSE
1 TOP_LEFT 1
2 TOP_RIGHT 2
3 COMPRESS_DOWN 3
4 COMPRESS_UP 4
5 TILT_RISE 5
6 TILT_FALL 6
7 TILT_SPARE 7
8 TILT_IVT_DO 8
9 TUBE_RISE 9
10 TUBE_FALL 10
11 TUBE_SPARE 11
12 TUBE_IVT_DO 12
13 24V 13
14 24V 14
15 24V 15
16 24V 16
17 GND 17
18 GND 18
19 GND 19
20 GND 20
21 COMPRESS_DOWN1 21
22 TUBE_SPEED_UP 22
23 TUBE_SPEED_DOWN 23
24 SID_IO_IN1 24
25 SID_IO_IN2 25
26 SID_IO_IN3 26
27 SID_IO_IN4 27
28 SID_IO_IN5 28
29 SID_IO_IN6 29
30 SID_IO_OUT1 30
31 31
32 TUBE_LOCK 32
33 MOTOR_RESERVE 33
34 34
Section 1.0
Introduction
This DICOM conformance statement specifies the behavior and functionality of the PRECISION
THUNIS-800+ DSA WorkStation application. This software provides the following capabilities:
- Storage Service Class (SCU) roles
- Verification Service Class (SCU) roles
- Basic Gray scale Print Management Class (SCU) roles
- Modality Worklist Management Service Class (SCU) roles
1.1 Scope:
This DICOM3.0 Conformance Statement documents the conformance of the PRECISION THUNIS-
800+ DSA WorkStation System product with the Digital Imaging and Communication in Medicine
(DICOM) Standard 2003. This document is released in order to evaluate whether or not another
DICOM compliant device can communicate with this software product.
This document describes the DICOM Conformance statement in accordance with the document
DICOM PS 3.2 Conformance.
1.1 References:
DICOM PS 3.1 Introduction
DICOM PS 3.2 Conformance
DICOM PS 3.3 Information Object Definitions
DICOM PS 3.4 Service Class Specifications
DICOM PS 3.5 Data Structures and Encoding
DICOM PS 3.6 Data Dictionary
DICOM PS 3.7 Message Exchange
DICOM PS 3.8 Network Communication Support for Message Exchange
Section 2.0
Implementation Model
PRECISION THUNIS-800+ DSA WorkStation system consists of a set of parallel, communicating
but independent processes that deal with the DICOM communication, capabilities include:
1. It can send images to a remote AE by utilizing the Storage Service Class as a SCU.
2. It supports the DICOM Verification service as a SCU.
3. It can send images to a DICOM Print Server AE by utilizing the Basic Grayscale Print
Management Service Class as a SCU.
4. It can query a DICOM Worklist Provider system for patient/study information using the Basic
Worklist Management Service Class as a SCU.
Section 3.0
AE Specifications
3.1 Send AE
This application entity provides Standard Conformance to the following DICOM3.0 SOP Classes as
a SCU:
SOP Class Name SOP Class UID
Verification SOP Class 1.2.840.10008.1.1
X-Ray Angiographic 1.2.840.10008.5.1.4.1.1.12.1
X-Ray Radio fluoroscopic 1.2.840.10008.5.1.4.1.1.12.2
3.1.1.1 General
All associations will be established using the DICOM3.0 Application Context. A single DICOM
Application Context Name is defined for this version of the DICOM standard is:
The Send AE will initiate an association as a SCU of Verification Services when user requests
DICOM verification to a remote DICOM AE.
The Send AE will initiate an association as a SCU of Storage Services when user requests DICOM
Storage to a remote DICOM AE.
The explicit VR transfer syntax with local byte order will always be the first in the list of the proposed
transfer syntaxes, followed by the explicit VR transfer syntax with opposite byte order, followed by
the DICOM default transfer syntax.
3.1.2.1.2.1 SOP Specific Conformance
Send AE transmits the selected objects from the local PRECISION THUNIS-800+ DSA
WorkStation database and creates a log entry for each C-STORE operation. The log entry shows
whether or not the transmission was successful.
If transmission of one selected object fails because no appropriate presentation context could be
negotiated, Send AE aborts the association and creates a log entry indicating the unsuccessful
termination. Send AE always transmits all elements contained in an object, independent from their
type within the IOD of the corresponding SOP Class.
Send AE never attempts to automatically repeat failed transmissions.
Extended negotiation is not supported.
See Annex A for a description of the IOD modules supported.
3.2 Print AE
This application entity provides standard Conformance to the following DICOM V3.0 SOP Classes
as a SCU:
This application entity does not provide standard conformance to any SOP class as SCP.
3.2.1.1 General
All associations will be established using the DICOM3.0 Application Context. A single DICOM
Application Context Name is defined for this version of the DICOM standard is:
The explicit VR transfer syntax with local byte order will always be the first in the list of the proposed
transfer syntaxes, followed by the explicit VR transfer syntax with opposite byte order, followed by
the DICOM default transfer syntax.
3.2.2.1.2.1 SOP Specific Conformance
3.3 Worklist AE
This application entity provides standard Conformance to the following DICOM V3.0 SOP Classes
as a SCU:
This application entity does not provide standard conformance to any SOP class as SCP.
3.3.1.1 General
All associations will be established using the DICOM3.0 Application Context. A single DICOM
Application Context Name is defined for this version of the DICOM standard is:
Section 4.0
Network Communication Profiles
4.1 Supported Communication Stacks
The PRECISION THUNIS-800+ DSA WorkStation system provides DICOM V3.0 TCP/IP Network
Communication Support as defined in Part 8 of the DICOM Standard (PS 3.8 Network
Communication Support for Message Exchange).
4.3.1 API
The PRECISION THUNIS-800+ DSA WorkStation system make use of the Winsock interface on
Windows platforms.
Section 5.0
Extensions/Specializations/Privatizations
Not supported or negotiated.
Section 6.0
Configuration
The PRECISION THUNIS-800+ DSA WorkStation system obtains its configuration information from
the following files:
Config.mdb file - Defines services on remote AEs to which connections are possible.
6.2.1 Send AE
For the Send AE entity, the following parameters are configurable for each send target:
• Presentation address (DNS hostname or IP address)
• IP port number
• Called application entity title
The number of send targets is not restricted. Send AE always uses the same application entity title
as the Store SCP.
6.2.2 Print AE
For the Print SCU component, the following parameters are configurable for each target printer:
• Presentation address (DNS hostname or IP address)
• IP port number
• Called application entity title
• Support for the optional Trim element in the Basic Film Box SOP Class (default: off)
• Supported STANDARD\C, R Image Display Formats
• Supported Film Size IDs (default: 14IN×17IN)
• Supported Medium Types (default: CLEAR FILM)
• Supported Magnification Types (default: BILINEAR)
• Supported Border Density identifiers (default: BLACK)
• Supported Empty Image Density identifiers (default: BLACK)
• Supported Max Density identifiers (default: 300)
• Supported Min Density identifiers (default: 20)
• Supported Print Priority (default: MED)
• Supported Print Destination (default: PROCESSOR)
• Supported Orientation (default: PORTRAIT)
The Print Type is ‘Grayscale’, which is not Configurable.
6.2.3 Worklist AE
For the Worklist AE entity, the following parameters are configurable for each send target:
• Presentation address (DNS hostname or IP address)
Section 7.0
Support of Extended Character Sets
This application supports only ISO_IR 100 (ISO 8859-1 Latin 1) as extended character set.
Section 8.0
SECURITY PROFILES
Not supported or negotiated.
Section 9.0
Annex A - DICOM Data Elements Supported
˭˲
˭˳
˭˴
˭˵
Section 10.0
Annex B - Print AE Attributes
SOP Class Name Command Attribute Name Valid Range Default Value
Basic Film Session N_CREATE Number of Copies From 1 to the Max 1
value of the SCP
Print Priority HIGH, MEDIUM,
LOW
Medium Type CLEAR FILM, CLEAR FILM
BLUE FILM
Film Destination MAGAZINE, PROCESSOR
PROCESSOR,
Basic Film Session N_ACTION Referenced Print Job None
Basic Film Box N_CREATE Image Display Format STANDARD\C,R STANDARD\C,R
Film Orientation PORTRAIT, PORTRAIT
LANDSCAPE
Film Size 14INX17IN, 14INX17IN
11INX14IN,
8INX10IN
etc.
Magnification Type REPLICATE, BILINEAR
BILINEAR, CUBIC,
NONE
ˮˬ
ˮ˭
Section 11.0
Annex C - Worklist AE Attributes
ˮˮ