Professional Documents
Culture Documents
Copyright 2008 Cisco Systems, Inc. ISBN-10: 1-58720-182-8 ISBN-13: 978-1-58720-182-0 Warning and Disclaimer
Every effort has been made to make this book as complete and as accurate as possible, but no warranty or fitness is implied. The information provided is on an "as is" basis. The author and the publisher shall have neither liability nor responsibility to any person or entity with respect to any loss or damages arising from the information contained in this book or from the use of the CD or programs accompanying it. When reviewing corrections, always check the print number of your book. Corrections are made to printed books with each subsequent printing. Note: Due to some oddities in the printing production process, multiple print runs may have the same printing number. To fully identify some printings, you must look at the copyright page, and find both the printing number and the printing month/year. In this errata file, when the same print run number has been used for multiple printings, the printing number and date is listed in this errata file. Please compare this to your books copyright page to find the correct printing and section to begin with in this errata file.
13th Printing
(Includes previous printings)
Page 110 1st paragraph under the note 1st 2 lines ICANN actually stands for Internet Corporation for Assigned Names and Numbers. Page 309 last paragraph end of line 2 overlap enough to impact change to overlap, so they do not impact Page 487 Last paragraph the reference to Ctl-Shift-6 add after that sentence: (Note that Ctl-Shift-6 sends a break character; some international keyboards may map a different key sequence to send a break character.) Page 499 figure 15-8 router R1 interface number S0/0/1, just below/right of router R1 icon, should instead be S0/1/1, to be consistent with earlier figures.
12th Printing
(Includes previous printings) Cisco Press ICND1 Exam Certification Guide Errata Last Update: June 3, 2011
Page 216 last bullet in list text console line configuration mode should be interface configuration mode Page 473 Question 5 answer B and Question 6 answer D change 10.1.13.3 to 10.1.13.2.
11th Printing
10th Printing
(Includes previous printings)
Page 445 Example 14-4 5th line with highlighted text refers to 10.1.128.251 should instead be 10.1.1.251. Note that some earlier printings do not have this error.
9th Printing
7th Printing
Cisco Press ICND1 Exam Certification Guide Errata Last Update: June 3, 2011
Page 352 1st paragraph 3rd line repeats "two-fifty-five" 4 times it should instead list that phrase 3 times, followed by "zero", being the wording version of 255.255.255.0. Page 461 2nd bullet point "16 seconds ago" should be "20 seconds ago". Pg 472 Figure at bottom of the page The address on R2s S0/1 interface should be changed from 10.1.13.3/30 to 10.1.13.2/30. Page 501 1st paragraph 2nd to last line text " link between R1 and R4" should instead be " link between R3 and R4." Page 504 example 15-10 3rd and 4th lines swap the references between FastEthernet 0/0 and FastEthernet 0/1. Pg 604 - Last definition on page - "CSU/DSU" Change the word "digital" to "data".
4th Printing
Cisco Press ICND1 Exam Certification Guide Errata Last Update: June 3, 2011
Page 495 4th paragraph 3rd line "between 172.31.25.1 and 172.31.25.126" should list a 3rd octet of "5", not "25", in both numbers. Page 583 Chapter 11, question 1, answer: Replace answer text with 802.11a uses the UNNI band of frequencies (around 5.4 GHz). 802.11b and 802.11g use the ISM band (around 2.4 GHz). 802.11i is a security standard. Appendix F (CD only) page 23 table F-6 Column 2, last row reads "Not shown", but instead should say "12.2(25)SE". Appendix F (CD-only) page 16 answer to question 6 reference to "7 seconds" should instead be "9 seconds".
3rd Printing
2nd Printing
Cisco Press ICND1 Exam Certification Guide Errata Last Update: June 3, 2011
Page 492 figure 15-5 the two bottom routers should be labeled R3 and R4, instead of R1 and R2, respectively. Page 178 figure 7-6 wrong figure. The correct figure is:
Page 207 last two entries in the bullet list should read No parity bits and 1 stop bit.
Cisco Press ICND1 Exam Certification Guide Errata Last Update: June 3, 2011