0% found this document useful (0 votes)
76 views1 page

36 Watt EL34 Superlite TMB Schematic

Uploaded by

guig.jones
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
76 views1 page

36 Watt EL34 Superlite TMB Schematic

Uploaded by

guig.jones
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

36 Watt EL34 Superlite TMB

Bright/Fat Switch
PILOT POWER STANDBY FX SEND FX RECEIVE (OPTIONAL) INPUT 2 (OPTIONAL) INPUT
SPST ON/OFF

Sleeve Sleeve
Sleeve Sleeve
HIGH MID LOW GAIN VOLUME

1M
B250K B50K A500K A1M A500K
Tip Tip
Tip Tip

.01µF

.01µF
V5
5AR4 / GZ34

47K

68K
68K

X Y

36 Watt OT
B
6.3

290

290

22µF 450v
15K

47µF 450v
2200µF 50v

SHIELDED WIRE
4.7K 3W

150Ω 20W

.022µF

500pF
.1µF
36 WATT PT

.047µF

.047µF
8.2K

8.2K

1µF

1µF
.022µF
.022µF

.022µF

.022µF
1K 3W

1K 3W

.01µF
(CENTER TAPPED)
C
ORANGE 16Ω C D
GREEN 8Ω C X

27K 3W
470Ω

680Ω
470K

470K

1.5K
3.18

3.18
240

120

YELLOW 4Ω
0

BLACK COM Y
D 56K
D

TIP TIP

N L
JMPGUITARS

JMPGUITARS
MUTE

MUTE
LIVE

LIVE

1.5K 5W
SLEEVE SLEEVE

L
50µF/50µF
Cap Can V4 V3 V2 V1
2A SLO BLO Fuse Rotary Impedance Parallel Output EL34 EL34 12AX7 12AX7
Combo IEC Socket Switch Jacks

Notes:
- Bright/Thick TONE switch is optional. FX loop is also optional. Jumper X and Y if not including FX loop (or use
one less turret if you’re sure you don’t want an FX loop).
THIS DRAWING IS THE PROPERTY OF JMPGUITARS AND SHALL NOT BE REPRODUCED, IN
WHOLE OR IN PART, WITHOUT THE WRITTEN PERMISSION OF JMPGUITARS. PERMISSION 36 Watt EL34 Superlite TMB
- It’s okay to connect the PT center taps to the same ground lug as the cap can. IS NOT GRANTED FOR SHARING OR DISPLAYING THIS IN ANY MANNER OUTSIDE OF
- The shielded wires to the board are probably optional. I would still use shielded wire going to the tube.
- The .047µF cap across the 47µF electrolytic cap is optional to help if there’s noise issues.
[Link] OR [Link]. NOT APPROVED FOR COMMERCIAL USE. Drawing by JMPGuitars
`
Tweaking:
AMPLIFIERS CONTAIN POTENTIALLY FATAL HIGH VOLTAGES. USE THIS Rev 3.6
- Use 820Ω resistor instead of 680Ω for less crunch. I don’t know why you’d want less crunch though. J Special thanks to Zaphod_Phil
INFORMATION AT YOUR OWN RISK. INFORMATION IS PROVIDED 'AS-IS' AND 04/11/2020
- To match Zaphod_Phil’s “Jalapeno” tone stack: use B50K for mid pot, replace 250pF treble cap with 470pF.
! WITHOUT WARRANTY OF ANY KIND.
Copyright © 2020 Joshua Peromsik

You might also like