Professional Documents
Culture Documents
Wireless 3900 Series Base Station Hardware Installation Telefonica
Wireless 3900 Series Base Station Hardware Installation Telefonica
Contents
1 Installation Scenarios and Exam
ple
2 Installation Technical key point
Installation scenarios
Typical
Jumper cable
Lightning protection ground clip
Feeder cable
Equipment room
Cable ladder
Jumper cable
BTS
Tower
alert
Battery
Lamp
PGND
Main-attached of
chamber inside
Outdoor eNodeB
BTS3900A
RFU
Multi-modal RRU
60W/4C
CDMA/WCDMA/LTE
GSM/UMTS/LTE
Distributed
eNodeB
DBS3900
RRU
BBU
Multi-modal BBU
2U 19-in rack mount
design
Use to 2G/3G/4G
operation
DBS3900 Overview
Antenna
system
Power
Transmissi
on
BBU
RRU
Environme
nt
Monitoring
etc.
WBBP/UBBP/LBBPUELP WMPT/UMPT
UPEU
FAN
BBU3900 consists of the following subsystems: baseband
subsystem, cabinet subsystem, transmission subsystem,
interconnection subsystem, main control subsystem, monitoring
subsystem, and clock subsystem.
Copyright 2014 Huawei Technologies Co., Ltd. All rights reserved.
Page 9
BBU3900
Configuration(normal)
BBU layout
In any scenario FAN UPEU UEIU boards are in the fixed slot
( )
(Max)
board type board name) (if integrant)
configuration order priority from left to right)
FAN
FAN
Yes
slot16
Power board
UPEU
Yes
slot19 slot18
monitoring)
EUIU
NO
slot18
BBU3900 Configuration(GBTS
scenario)
BBU3900 Configuration(UMTS
scenario)
BBU3900 Configuration(LTE
scenario)
[ndket]
CPRI
interface
Interconnect
interface
Power
connector
RET CONNECTOR
ANT Tx/Rx
PGND
ANT Rx
Page 16
RRU3942
Installation scenarios
on the Wall
Indoor on the Wall
Page 20
Page 21
Page 22
Description
Scenario
Scenario_P1
Scenario_P2
3*RRU+1*BBU
6*RRU+1*BBU
Scenario_P3
9*RRU+1*BBU
Scenario_P4
12*RRU+1*BBU
850M
850M+1900M
850M+1900M+2
600M
850M+1900M+2
600M+700M
Typical Power(W)
Maximum
Power(W)
883.71
1723.37
1440.59
2722.18
2543.96
3772.6
3263.96
4732.6
Connection Practice
Connection
Practice
Contents
Assemble the
support
Install the upper
support on the
antenna.
Install the lower
support on the
antenna.
Note:
Adjust the E-Tilt for each sector according to the planning.
Take the Photo for each sector after adjustment.
from tower
Do not tightly
secure the
screws on the
upper and
lower ,
convenient
azimuth
adjustment of
the antenna.
And also avoid
the antenna
drop from the
pole.
Copyright 2014 Huawei Technologies Co., Ltd. All rights reserved.
When lifting the RRU to the tower, avoid collision of the RRU
with the tower
When lift the RRU, bind the whole RRU but not only the handle
of the RRU
Pulley
Tensile
rope
Steering
rope
Lifting
rope
Steering
rope
Lifting
rope
Steering
rope
[p:pn
in perpendicular direction), and the
tie
should be in the same direction. dkjl]
Power cable:
[rdndnsi:]
Step2
The
waterproof
tape is
wrapped
spirally
upwards,
downwards
, and then
upwards
again in
three
layers
Step3
Step4
The
insulatio
n tape is
wrapped
spirally
upwards,
downwar
ds, and
then
upwards
again in
three
layers
Tightly
Seal the
two ends
of the
waterproo
f
connector
when
finish
wrapping
NOTE: For every two insulation tape layers, the tape on the upper
layer overlaps about half the width of the tape on the lower layer
Sector Fiber
1
2
3
Power
Cable
Jumper
Main
Diversity
Red
One ring Two ring One ring
color
Yellow
One ring Two ring One ring
color
Blue
One ring Two ring One ring
color
1
me
tro
Sali
da
1
1
me me
tro SHEL
tro
TER
RA
CK
19
1
m
etr
o
1 MI
m NIetr SH
o ELT
ER
Leftover FO Cables
El ingreso de conduits o cualquier orificio debe quedar sellado con sikaflex 11,
descartar la espuma. Los conduit que ingresan al gabinete deben incluir un terminal
de conduit metalico.
Thank you
www.huawei.com