Professional Documents
Culture Documents
RF Troubleshooting
RF Troubleshooting
RSCP
That’s the received energy per chip (Ec) of the pilot channel
divided by the total noise power density (No). In other words EcIo
the EcNo in the RSCP divided by the RSSI (Received Signal
Strength Indication). The value of EcNo is negative as the
RSCP in smaller then the total received power. As the RSCP
this value can be used to compare different cells on the same
carrier and handover or cell reselection decisions can be taken.
We can measure the EcNo at User equipment by using G-
NetTrack Lite software.
RTWP is related to uplink interference, and its monitoring helps control the
call drops - mainly CS. It also has importance in the capacity management, as
it provides information for the Congestion Control regarding Uplink
Interference.
In a network is not loaded, normal, acceptable RTWP Average value is
generally around -104.5 and -105.5 dBm.
The transmission power is the maximum power of cell, this parameter affect to the transmission bandwidth. As the
results, the higher transmission, the more data throughput.
The value of transmission power
+ 20 W = 43 dBm
+ 30 W = 44.7 dBm
+ 40 W = 46 dBm
+ 60 W = 47.8 dBm
The CPICH Power related to wave covering area. CPICH power typically takes about 10% of the total Node B
power. If CPICH power is set too high, congestion may appear due to larger coverage, which implies that more users
may camp within the sector. Therefore, its power can be adjusted within the rules mentioned above, between 5-10%
of total power, in order to increase/reduce the effective covered area to cope with traffic load.
1. Ưu tiên change M-tilt and E-Tilt trước để tăng giảm vùng phủ sóng.
2. Change Power CPICH and Maximum Transmisson Power
3.2 Need Change Azimuth and add sector 4 (U2100)
3.1. Trường hợp chỉnh azimuth để tín hiệu được tốt hơn cho user ( Cần xem xét lại vùng phủ cũ số lượng user có cao
hay không hoặc cao nhưng có được trạm khác share phủ không )
3.2. Insert add sector 4 ( Trường hợp các sector lận cận hoặc trạm khác không thể chỉnh azimuth về hướng có tín hiệu
kém )
4. Insert add U900 ( Note: Trường hợp check 2/3 sector số lượng user người dùng trong 1 tuần là high) and Indoor
Repeater
5. Insert add New Site ( Note: Khi không thể áp dụng các trường hợp trên )
1. Ưu tiên change M-tilt and E-Tilt trước để tăng giảm vùng phủ sóng.
2. Change Power CPICH and Maximum Transmisson Power
3.2 Need Change Azimuth and add sector 4 (U2100)
3.1. Trường hợp chỉnh azimuth để tín hiệu được tốt hơn cho user ( Cần xem xét lại vùng phủ cũ số lượng user có cao
hay không hoặc cao nhưng có được trạm khác share phủ không )
3.2. Insert add sector 4 ( Trường hợp các sector lận cận hoặc trạm khác không thể chỉnh azimuth về hướng có tín hiệu
kém )
4. Insert add U900 ( Note: Trường hợp check 2/3 sector số lượng user người dùng trong 1 tuần là high) and Indoor
Repeater
5. Insert add New Site ( Note: Khi không thể áp dụng các trường hợp trên )
© ZTE All rights reserved
12
2.3 How to change Tilt. Internal use only▲
STEP 1
STEP 1
- Nhiễu uplink:
+ Khi cell có nhiều user dùng có thể gây ra nhiễu.
+ Nhiễu do thiết bị : như do anten, card baseband nodeB, Jumper…
+ Nhiễu ngoài: như cùng hài với tần số nhà mạng khác…
U2100 and U900 sự khác biệt về ký hiệu. F1 cho 4G: F1: 2147.6 HSDPA avearge user
F2 cho 3G: F2: 2152.6 Mỗi cell tối đa nên support cho 20 user.
User U900 phải đảm bảo < user U2100 ( dao động từ <10
user/cell is good )
Đối với thiết bị ZTE: thì SFP trong nodeB sẽ có Rack
51,52,53,54,55,56 đếm từ phải sang trái
+ Normal rack 51,52,53 for U2100.
+ Normal rack 54,55,56 for U900.
+ Norrmal rack 57,58,59 for cell Spliter.
Trong 4G
© ZTE All rights reserved
35
Internal use only▲