Professional Documents
Culture Documents
HVIB更换指导
HVIB更换指导
-1-
HVIB 板更换指导
HVIB replacement instruction
步骤
4 5 6
Step
描述 1) 从控制柜安装板后侧卸下 从包装箱内按下图的拿取方式取出新的 固定所有的螺栓,恢复所
Description 散热器的固定螺丝; HVIB 板,并保持用这种操作方式将 HVIB 有电缆的连接。最后将拆
2) 从正面按 1-2-3-4 顺序卸 板安装至控制柜。 下的旧 HVIB 板装回包装
下安装螺栓,在卸第 3 , 4 Take out the new HVIB from the 箱内发回工厂
个螺丝时请用手托住散热器 package with the handling method as Screw all bolts and
。 below, and keep the handling method to connect all cables.
1 ) Unscrew bolt jointed install the HVIB in controller. Finally put the original
with heat sink at rear plate; HVIB into the package
2) Unscrew the bolt at front 注意 HVIB
注意 HVIB 的握持方式,
的握持方式, and ship back to factory
following the sequence of 1- 勿直接施力于电路板!
勿直接施力于电路板!
2-3-4. the worker must Note
Note the
the handling
handling method
method
catch the heat sink at step
3,4
图片
Picture
XOEC
-2-
参数设置
步骤 参数设置步骤——以下菜单均为变频器菜单
第1步 M-2-6-4 : Factory Password(工厂密码) :638
第2步 GO ON
第3步 I2CEE Val@2.0000 (服务器显示)
第4步 Input data 20, Shift + Enter
第5步 Shift + UP
第6步 I2CEE Val@2.0002 (服务器显示)
第7步 Input data 4, Shift + Enter
第8步 Shift + Up
第9步 I2CEE Val@2.0004 (服务器显示)
第10步 Input data 40 (ACD2 MR 404), 30 (ACD2 MR 403), 20 (ACD2 MR 402), 15 (ACD2 MR 401), Shift + Enter
第11步 Shift + Up
第12步 I2CEE Val@2.0006 (服务器显示)
第13步 Input data 2, Shift + Enter
第14步 Shift + Down (检查设置的参数)
第15步 M2-2-5 DSP reset
XOEC
-3-
LCRD&UD 变频器参数设置
LCRD 变频器参数设置
Parameter Default value Real Value
*Factory Password 0 638
*I2CEE Val@2.0000 20 20
*I2CEE Val@2.0002 4 4
*I2CEE Val@2.0004 0 20(402),30(403),40(404)
*I2CEE Val@2.0006 2 2
UD 变频器参数设置
Parameter Default value Real Value
*Factory Password 0 638
*I2CEE Val@2.0000 20 20
*I2CEE Val@2.0002 4 4
*I2CEE Val@2.0004 0 20(402),30(403),40(404)
XOEC
*I2CEE Val@2.0006 2 3
-4-