Professional Documents
Culture Documents
B Black
L Blue
R Red
P Pink
G Green
W White
V Violet
O Orange
Y Yellow
BR Brown
SB Sky Blue
LG Light Green
GR Gray
Year 2000-2002
Connector E5 (D) E4 (C) E3 (B) E2 (A)
Pin Color Label Notes Color Label Notes Color Label Notes Color Label Notes
1 R #10 Injector #1 Ground Control Y-G EVG MAFS Signal Wire B OD1 OD Com wire to Crs Cntrl ECU W BATT Power from EFI Relay
2 R-L #20 Injector #2 Ground Control R VC +5v to TPS & EVAP VPS R-B R R signal from gear selector
3 R-W #30 Injector #3 Ground Control Y-R HT1A Front O2 Heater Circuit Ground L-W CF Rly Cntrl Gnd For Fan Rly #3 G-R FC (Fuel Cut) Circ Open Rly Cntrl Gnd
4 R-B #40 Injector #4 Ground Control G-O EVP1 Control ground EVAP purge VSV L-Y FAN Rly Cntrl Gnd For Fan Rly #1 L-B PTNK EVAP Vapor Pres Sens Signal
5 Y-G SLT- SLT solenoid wire P-B TC TC com wire to DLC3 Diag cnctr BR-Y ODMS Overdrive Main Switch
6 Y-R SLT+ SLT solenoid wire L-B OVL- VVL OCV Control Wire G-W STP Stop Light Switch signal LG-R MPX2 Multiplex Communications Wire 2
7 G SL1+ SL solenoid wire L-W OVL+ VVL OCV Control Wire W-B E03 E03 Ground circuit - to EC Ground
8 BR-Y SL2 SL2 solenoid wire P-L N N signal from gear selector P F/PS GSW2 wire to Ctr A/B Sens Assy B-O IGSW 12V Ignition source signal
9 V SL1- SL solenoid wire Y-B L L signal from gear selector R-L VSV VSV Cntrl Gnd for ACIS VSV L SFTU Shift Up switch input
10 R-B IGT1 Igniter 1 Fire Signal Y RL Alternator Load Signal Wire LG-R MPX1 Multiplex Communications Wire 1 L-W IDLO IDL com wire to Cruise Cntrl ECU
11 R-W IGT2 Igniter 2 Fire Signal G-W VG +5v to MAFS L STA 12v starter signal (during crank) W SIL SIL com wire to DLC3 Diag Cnctr
12 G-R IGT3 Igniter 3 Fire Signal B OX1A Front O2 Signal Wire W-B EC Ground (EB on left front fender) Y-B ACMG Gnd cntrl for A/C mag clutch rly
13 R-Y IGT4 Igniter 4 Fire Signal GR-L THO Trans fluid temp sensor
14 P-B NC+ O/D Direct Clutch Speed Sensor G THW Coolant Temp. Sensor B-W CCE D signal to cruise control ECU
15 B NT- VSS (Electr. Controled Trans) L G2 Cam Position Sensor Signal R-B W Check Engine Light control ground
16 W-L NT+ VSS (Electr. Controled Trans) O NE+ Crank Position Sensor Signal Y-B HT1B Rear O2 Heater Circuit Ground B-R B+ +12v from C/OPN rly & 7.5A EFI #1 fuse
17 V-W CCV Control Ground EVAP CCV VSV BR E1 ECU shielding & sensor ground P SFTD Shift Down switch input
18 B-W RSO IAC Valve Control Wire BR E2 Sensor Ground O PRE From A/C Dual Pressure SW
19 P-L DSL DSL solenoid wire L-Y 2 2 signal from gear selector BR-Y ODLP O/D lamp control ground
20 O SL2- SL2 solenoid wire P P P signal from gear selector
21 W-B E01 Ground to ED ground point GR OSW Oil Pressure Switch (VVTL) L-B MREL Control ground EFI mail relay
22 Y-B MOPS Oil Pressure Switch L-R THA MAFS (air temp signal) W-R SPD Speed signal from combo meter
23 W OCV- VVT OCV B-W VTA TPS Signal G-O TBP Control ground EVAP bypass VSV
24 G-O OCV+ VVT OCV W NE- Crank & Cam Sensor Ground L-W D D signal from gear selector
25 B-Y IGF Igniter Fire Confirmation Signal W OX1B Rear O2 Signal Wire
26 G-W NC- O/D Direct Clutch Speed Sensor
27 W* KNK1 Knock Sensor* BR-W TACH Output to tachometer
28 P* PS Pwr. St. Oil Pres. SW G LCKI A/C MG/C Lock Sensor Signal
29 Y S4 S4 solenoid wire
30
31 W-B E02 Ground to ED ground point
* On 2002 wire harness, KNK1 is a black wire on Connector D/E5, pin 27. EKNK is a white wire on pin 28, displacing PS (pink wire) to pin 30.
= Related to cruise control system. Does not cross into ECU harness, additional retrofit info needed.
= Related to EVAP system. Cross directly.
= Automatic Transmission only.
= Related to non-essential systems. Cross dire
Year 2003
Connector E10 (G) E11 (H) E12 (I)
Pin Color Label Notes Color Label Notes Color Label
1 L-R #10 Injector #1 Ground Control W EKNK Knock Sensor Ground BR E1
2 L-O #20 Injector #2 Ground Control B KNK1 Knock Sensor W M-
3 L-B #30 Injector #3 Ground Control B M+
4 L #40 Injector #4 Ground Control Y-R HT1A Front O2 Heater Circuit Ground W-R ME01
5 L-W CF Rly Cntrl Gnd For Fan Rly #3
6 W-B E02 Ground to ED ground point Y-G HT1B
7 W-B E01 Ground to ED ground point W-G E03
8 R-G IGT1 Igniter 1 Fire Signal GR OSW
9 GR-R IGT2 Igniter 2 Fire Signal L STA 12v starter signal (during crank)
10 G-R IGT3 Igniter 3 Fire Signal P PS
11 R-Y IGT4 Igniter 4 Fire Signal P-L DSL DSL solenoid wire G-Y EVP1
12 V-W CCV
13 Y S4 S4 solenoid wire L-W OVL+
14 L-Y FAN Rly Cntrl Gnd For Fan Rly #1 L-B OVL-
15 R-L VSV VSV Cntrl Gnd for ACIS VSV W OCV-
16 Y-G SLT- SLT solenoid wire O SL2- SL2 solenoid wire G-O OCV+
17 Y-L SLT+ SLT solenoid wire BR-Y SL2 SL2 solenoid wire GE01
18 R-B VC +5v to TPS & EVAP VPS V SL1- SL solenoid wire
19 G THW Coolant Temp. Sensor G-R SL1+ SL solenoid wire
20 Y-R THA MAFS (air temp signal)
21 B-W VTA TPS Signal #1 Y RL
22 Y-B MOPS
23 B OX1A Front O2 Signal Wire G LCKI
24 B-Y IGF Igniter Fire Confirmation Signal G-W VG +5v to MAFS
25
26 P-B NC+ O/D Direct Clutch Speed Sensor
27 O NE+ Crank Position Sensor Signal W-L NT+ VSS (Electr. Controled Trans) L G2
28 BR E2 Sensor Ground
29 R OX1B Rear O2 Signal Wire
30 GR-L THO Trans fluid temp sensor W-B EC
31 B-L VTA2 TPS Signal #2 (Idle Control)
32 Y-G EVG MAFS Signal Wire
33
34 W NE- Crank & Cam Sensor Ground G-O NC- O/D Direct Clutch Speed Sensor
35 B-R NT- VSS (Electr. Controled Trans)
= Related to cruise control system. Does not cross into ECU harness, additional retrofit info needed.
= Specific to 2003-2005 ECU. Not used in cable throttle conversion.
= Related to EVAP system.
= Non-essential systems.
= Automatic Transmission only.
2003
E12 (I) E8 (E) E9 (F)
Notes Color Label Notes Color Label
ECU shielding & sensor ground O HP From A/C Dual Pressure SW B-R B+
DBW Related Y-O ACMG Gnd cntrl for A/C mag clutch rly
DBW Related W-L BATT
Ground G-O TBP
BR-W TACH
Rear O2 Heater Circuit Ground W-R +BM +12v from 10A ETCS fuse P P
E03 Ground circuit - to EC Ground BR-Y ODLP O/D lamp control ground P-L N
Oil Pressure Switch (VVTL) Y-B L L signal from gear selector GR MREL
L-O 2 2 signal from gear selector B-O IGSW
Power Steer. Oil Pres. Sw. L-W D* D signal from gear selector G-R FC
Control ground EVAP purge VSV R-B R R signal from gear selector R-B W
Control Ground EVAP CCV VSV R-Y ST1- Brake Cancel Cruise Cntrl.
VVL OCV Control Wire Y-G PI To Cruise Control Light
VVL OCV Control Wire P-G F/PS
VVT OCV
VVT OCV BR-R ODMS
DBW Related W-R SPD Speed signal from combo meter
LG-R MXP1 Multiplex Communications Wire 1 W SIL
G-W STP Stop Light Switch signal G WFSE
P-B TC
Alternator Load Signal Wire P-L SFTD Shift Down switch input L-B PTNK
Oil Pressure Switch L-R SFTU Shift Up switch input L-Y VPA
A/C MG/C Lock Sensor Signal L-O VPA2
W-G CCS From Cruise Cntrl. Sw.
L-W VCPA
Cam Position Sensor Signal L VCP2
L-R EPA
G-O MXP2 Multiplex Communications Wire 2 LG-R EPA2
Ground (EB on left front fender)
E9 (F)
Notes
+12v from C/OPN rly & 7.5A EFI #1 fuse
= Related to cruise control system. Does not cross into ECU harness, additional retrofit info needed.
= Specific to 2003-2005 ECU. Not used in cable throttle conversion.
= Related to EVAP system.
= Non-essential systems.
= Automatic Transmission only.
2004-2005
E12 (I) E8 (E) E9 (F)
Notes Color Label Notes Color Label
ECU shielding & sensor ground O HP From A/C Dual Pressure SW B-R B+
DBW Related Y-O ACMG Gnd cntrl for A/C mag clutch rly
DBW Related W-L BATT
Ground G-O TBP
BR-W TACH
Rear O2 Heater Circuit Ground W-R +BM Battery +12v Non-Switched P P
E03 Ground circuit - to EC Ground BR-Y ODLP O/D lamp control ground P-L N
Oil Pressure Switch (VVTL) Y-B L L signal from gear selector GR MREL
L-O 2 2 signal from gear selector B-O IGSW
Power Steer. Oil Pres. Sw. L-W D* D signal from gear selector G-R FC
Control ground EVAP purge VSV R-B R R signal from gear selector R-B W
Control Ground EVAP CCV VSV R-Y ST1- Brake Cancel Cruise Cntrl.
VVL OCV Control Wire Y-G PI To Cruise Control Light
VVL OCV Control Wire P-G F/PS
VVT OCV
VVT OCV BR-R ODMS
DBW Related W-R SPD Speed signal from combo meter
LG-R MXP1 Multiplex Communications Wire 1 W SIL
G-W STP Stop Light Switch signal G WFSE
P-B TC
Alternator Load Signal Wire P-L SFTD Shift Down switch input L-B PTNK
Oil Pressure Switch L-R SFTU Shift Up switch input L-Y VPA
A/C MG/C Lock Sensor Signal L-O VPA2
W-G CCS From Cruise Cntrl. Sw.
L-W VCPA
Cam Position Sensor Signal L VCP2
L-R EPA
G-O MXP2 Multiplex Communications Wire 2 LG-R EPA2
Ground (EB on left front fender)
E9 (F)
Notes
+12v from C/OPN rly & 7.5A EFI #1 fuse
1 OD1
2 E8 (E) 11 R-B E8 (E) 11 R-B R
3 E10 (G) 5 L-W E10 (G) 5 L-W CF
4 E10 (G) 14 L-Y E10 (G) 14 L-Y FAN
5 E9 (F) 20 P-B E9 (F) 20 P-B TC
6 E8 (E) 19 G-W E8 (E) 19 G-W STP
7
8 E9 (F) 14 P-G E9 (F) 14 P-G F/PS
9 E10 (G) 15 R-L E10 (G) 15 R-L VSV
10 E8 (E) 18 LG-R E8 (E) 18 LG-R MXP1
11 E11 (H) 9 L E11 (H) 9 L STA
12 E12 (I) 30 W-B E12 (I) 30 W-B EC
13
14 CCE
E3 (B)
15
16 E12 (I) 6 Y-G E12 (I) 6 Y-G HT1B
17
18 E8 (E) 1 O E8 (E) 1 O PRE/HP
19 E8 (E) 7 BR-Y E8 (E) 7 BR-Y ODLP
20
21 E9 (F) 8 GR E9 (F) 8 GR MREL
22 E8 (E) 17 W-R E8 (E) 17 W-R SPD
23 E9 (F) 4 G-O E9 (F) 4 G-O TBP
24 E8 (E) 10 L-W E8 (E) 10 L-W D
25 E11 (H) 29 R E11 (H) 29 R OX1B
26
27 E9 (F) 5 BR-W E9 (F) 5 BR-W TACH
28 E12 (I) 23 G E12 (I) 23 G LCKI
Notes
*1 See IAC tab. This wire is retrofitted from MAFS connector on 2003-05 harness
Fields highlighted in Orange denote circuits used for Automatic Transmission only
Fields highlighted in Yellow denote circuits used for EVAP System
Fields highlighted in Aqua denote circuits used for Cruise Control system that will not cross into the 2003-05 harness
Fields highlighted in Green denote additional non-essential systems such as air conditioning, intake flapper door and OBD-II d
Description
Power from EFI relay
Destination Source
2000-2002 Connectors 2003-2005 Connectors
Connector Pin Color Connector Pin Color Function
1 BR T1 3 BR Ground
T1 2 R T1 5 R-B Power
3 B-W T1 6 B-W Signal
Destination Source
2000-2002 Cruise Control ECU 2003-2005 Connectors
Connector Pin Color Connector Pin Color Function
1
2 G-W STP-
3 B-Y D
4 Y-B PI
5 P-B TC
6 Y-B ECT
7 R-W MC
8 G-B L
C18
9 B-O B
10 W-B CCS
11
12 W-R SPD
13 L-W IDL
14 B OD
15 R-L MO
16 W-B GND
Destination Source
2000-2002 Cruise Control Actuator 2003-2005 Connectors
Connector Pin Color Connector Pin Color Function
1 R-L MO
2 R-W MC
C5
3 R-Y L
4 W-B GND
Description
A/T ONLY
Description