Professional Documents
Culture Documents
2N6071A/B Series Sensitive Gate Triacs: Silicon Bidirectional Thyristors
2N6071A/B Series Sensitive Gate Triacs: Silicon Bidirectional Thyristors
2N6071A/B Series Sensitive Gate Triacs: Silicon Bidirectional Thyristors
Preferred Device
http://onsemi.com
MARKING DIAGRAM
YWW 2N 607xyG = 1, 3, 5 = A, B = Year = Work Week = Pb-Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet.
Preferred devices are recommended choices for future use and best overall value.
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
2N6071A/B Series
MAXIMUM RATINGS (TJ = 25C unless otherwise noted)
Rating *Peak Repetitive OffState Voltage (Note 1) (TJ = *40 to 110C, Sine Wave, 50 to 60 Hz, Gate Open) 2N6071A,B 2N6073A,B 2N6075A,B *OnState RMS Current (TC = 85C) Full Cycle Sine Wave 50 to 60 Hz *Peak Non-repetitive Surge Current (One Full cycle, 60 Hz, TJ = +110C) Circuit Fusing Considerations (t = 8.3 ms) *Peak Gate Power (Pulse Width 1.0 ms, TC = 85C) *Average Gate Power (t = 8.3 ms, TC = 85C) *Peak Gate Voltage (Pulse Width 1.0 ms, TC = 85C) *Operating Junction Temperature Range *Storage Temperature Range Mounting Torque (632 Screw) (Note 2) Symbol VDRM, VRRM 200 400 600 IT(RMS) ITSM I2t PGM PG(AV) VGM TJ Tstg 4.0 30 3.7 10 0.5 5.0 -40 to +110 -40 to +150 8.0 A A A2s W W V C C in. lb. Value Unit V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. VDRM and VRRM for all types can be applied on a continuous basis. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. 2. Torque rating applies with use of a compression washer. Mounting torque in excess of 6 in. lb. does not appreciably lower casetosink thermal resistance. Main terminal 2 and heatsink contact pad are common.
THERMAL CHARACTERISTICS
Characteristic *Thermal Resistance, Junction-to-Case Thermal Resistance, Junction-to-Ambient Maximum Lead Temperature for Soldering Purposes 1/8 from Case for 10 Seconds *Indicates JEDEC Registered Data. Symbol RqJC RqJA TL Max 3.5 75 260 Unit C/W C/W C
http://onsemi.com
2
2N6071A/B Series
ELECTRICAL CHARACTERISTICS (TC = 25C unless otherwise noted; Electricals apply in both directions)
Characteristic OFF CHARACTERISTICS *Peak Repetitive Blocking Current (VD = VDRM = VRRM; Gate Open) ON CHARACTERISTICS *Peak OnState Voltage (Note 3) (ITM = "6.0 A Peak) *Gate Trigger Voltage (Continuous DC), All Quadrants (Main Terminal Voltage = 12 Vdc, RL = 100 W, TJ = -40C) Gate Non-Trigger Voltage, All Quadrants (Main Terminal Voltage = 12 Vdc, RL = 100 W, TJ = 110C) *Holding Current (Main Terminal Voltage = 12 Vdc, Gate Open, Initiating Current = "1 Adc) TJ = -40C TJ = 25C TurnOn Time (ITM = 14 Adc, IGT = 100 mAdc) VTM VGT VGD 0.2 IH tgt 1.5 30 15 ms mA 1.4 2.5 V 2 V V TJ = 25C TJ = 110C IDRM, IRRM 10 2 mA mA Symbol Min Typ Max Unit
QUADRANT (Maximum Value) Type Gate Trigger Current (Continuous DC) (Main Terminal Voltage = 12 Vdc, RL = 100 W) 2N6071A 2N6073A 2N6075A 2N6071B 2N6073B 2N6075B DYNAMIC CHARACTERISTICS Critical Rate of Rise of Commutation Voltage @ VDRM, TJ = 85C, Gate Open, ITM = 5.7 A, Exponential Waveform, Commutating di/dt = 2.0 A/ms 3. Pulse Test: Pulse Width 2.0 ms, Duty Cycle 2%. *Indicates JEDEC Registered Data. dv/dt(c) 5 V/ms IGT @ TJ +25C -40C +25C -40C I mA 5 20 3 15 II mA 5 20 3 15 III mA 5 20 3 15 IV mA 10 30 5 20
SAMPLE APPLICATION: TTLSENSITIVE GATE 4 AMPERE TRIAC TRIGGERS IN MODES II AND III
14 MC7400 4 7 VEE = 5.0 V + 2N6071A LOAD 115 VAC 60 Hz
0V
-VEE
510 W
Trigger devices are recommended for gating on Triacs. They provide: 1. Consistent predictable turnon points. 2. Simplified circuitry. 3. Fast turnon time for cooler, more efficient and reliable operation.
http://onsemi.com
3
2N6071A/B Series
Voltage Current Characteristic of Triacs (Bidirectional Device)
Symbol
VDRM IDRM VRRM IRRM VTM IH
Parameter
Peak Repetitive Forward Off State Voltage Peak Forward Blocking Current Peak Repetitive Reverse Off State Voltage Peak Reverse Blocking Current Maximum On State Voltage Holding Current Quadrant 3 MainTerminal 2 IH VTM IRRM at VRRM on state IH
VTM
off state
(+) MT2
(+) MT2
Quadrant II
Quadrant I
+ IGT
Quadrant III
Quadrant IV
MT2 NEGATIVE (Negative Half Cycle) All polarities are referenced to MT1. With in-phase signals (using standard AC lines) quadrants I and III are used. SENSITIVE GATE LOGIC REFERENCE
IC Logic Functions
TTL HTL CMOS (NAND) CMOS (Buffer) Operational Amplifier Zero Voltage Switch 2N6071A Series 2N6071A Series 2N6071A Series 2N6071B Series 2N6071B Series 2N6071B Series 2N6071A Series
Firing Quadrant I II
2N6071A Series 2N6071A Series
III
2N6071A Series 2N6071A Series
IV
2N6071B Series
http://onsemi.com
4
2N6071A/B Series
110 110 = 30 60 TC , CASE TEMPERATURE ( C) TC , CASE TEMPERATURE ( C) 90 100 100 = 30 60 90 90 120 180 dc 80 70 = CONDUCTION ANGLE 0 1.0 2.0 3.0 IT(AV), AVERAGE ONSTATE CURRENT (AMP) 4.0 a
90
120 180
80 a 70
dc
= CONDUCTION ANGLE 0 1.0 2.0 3.0 IT(RMS), RMS ONSTATE CURRENT (AMP) 4.0
dc = 180 120
2.0
2.0 90 0
30 60
4.0
0.3 -60
-40
-20
120
140
0.3 -60
-40
-20
120
140
http://onsemi.com
5
2N6071A/B Series
40 30 20 IH, HOLDING CURRENT (NORMALIZED) 3.0 2.0 GATE OPEN APPLIES TO EITHER DIRECTION
0.3 -60
-40
-20
20
40
60
80
100
120
140
3.0 2.0
0.3 0.2
0.1 0 1.0 2.0 3.0 4.0 5.0 VTM, ONSTATE VOLTAGE (VOLTS)
2.0
3.0
4.0
5.0
7.0
10
MAXIMUM
TYPICAL 1.0 0.5 0.3 0.2 0.1 0.1 0.2 0.5 1.0 2.0 5.0 10 20 50 t, TIME (ms) 100 200 500 1.0 k 2.0 k 5.0 k 10 k
http://onsemi.com
6
2N6071A/B Series
ORDERING INFORMATION
Device 2N6071A 2N6071AG 2N6071AT 2N6071ATG 2N6071B 2N6071BG 2N6071BT 2N6071BTG 2N6073A 2N6073AG 2N6073B 2N6073BG 2N6075A 2N6075AG 2N6075B 2N6075BG Package TO-225 TO-225 (Pb-Free) TO-225 TO-225 (Pb-Free) TO-225 TO-225 (Pb-Free) TO-225 TO-225 (Pb-Free) TO-225 TO-225 (Pb-Free) TO-225 TO-225 (Pb-Free) TO-225 TO-225 (Pb-Free) TO-225 TO-225 (Pb-Free) 500 Units / Box 500 Units / Box 50 Units / Tube 2000 Units / Box 50 Units / Tube 2000 Units / Box 500 Units / Box 50 Units / Tube 2000 Units / Box 50 Units / Tube 2000 Units / Box Shipping
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
7
2N6071A/B Series
PACKAGE DIMENSIONS
TO-225 CASE 77-09 ISSUE Z
-BU Q -A1 2 3
F M
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 077-01 THRU -08 OBSOLETE, NEW STANDARD 077-09. INCHES MIN MAX 0.425 0.435 0.295 0.305 0.095 0.105 0.020 0.026 0.115 0.130 0.094 BSC 0.050 0.095 0.015 0.025 0.575 0.655 5 _ TYP 0.148 0.158 0.045 0.065 0.025 0.035 0.145 0.155 0.040 --MILLIMETERS MIN MAX 10.80 11.04 7.50 7.74 2.42 2.66 0.51 0.66 2.93 3.30 2.39 BSC 1.27 2.41 0.39 0.63 14.61 16.63 5 _ TYP 3.76 4.01 1.15 1.65 0.64 0.88 3.69 3.93 1.02 ---
V G S D 2 PL 0.25 (0.010)
M
J R 0.25 (0.010) A
M
A
M
DIM A B C D F G H J K M Q R S U V
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
http://onsemi.com
8
2N6071/D