Professional Documents
Culture Documents
Header Board 51292S
Header Board 51292S
Production Device
To Tool Connector
DS51292S-page 1
FIGURE 2:
Debug Circuitry No debug capability. Header required for debug. Debug capability available. However, header can provide dedicated resources for debug.
ICE/ICD Device with On-board Debug Circuitry, Dedicated Debug Pins and (sometimes) Dedicated Debug Memory. VDD MCLR VPP VSS DAT CLK Rx1 Rx0 Debug Memory Debug Circuitry
J1
ON
S1
In general, ICE devices are designed for next-generation in-circuit emulator use and ICD devices are designed for in-circuit debugger use. However, ICE devices may be used with an in-circuit debugger and ICD devices may be used with a next-generation in-circuit emulator, but will provide only basic ICD functionality. To determine what device resources must be dedicated to debugging for either a device with on-board debug capability or the special ICE/ICD device, see the Resources used by ... section of the in-circuit emulator or in-circuit debugger on-line help file.
DS51292S-page 2
CAUTION
2. Set any jumpers or switches on the header to determine device functionality or selection as specified for that header. See the sections Optional Headers or Required Headers for information on how to set up individual headers.
DS51292S-page 3
ICE/ICD Device
4. Connect the header to the target board. On the bottom of the header is a socket that is used to connect to the target board. The header may be connected to the target board as follows: a) PDIP header socket to PDIP target socket with a stand-off (male-to-male) connector b) Header socket to plug on the target board c) Header socket to target socket with a transition socket (see the Transition Socket Specification, DS51194) An example connection is shown in Figure 5. The header socket will have the same pin count as your selected device. The ICE/ICD device on the top of the header usually has a larger pin count because it has additional pins that are dedicated to debugging.
DS51292S-page 4
Target Socket
5. If using a debug tool that can power the target, power that tool now. 6. Power the target, if needed.
CALIBRATION BITS
The calibration bits for the band gap and internal oscillator are always preserved to their factory settings.
PERFORMANCE ISSUES
The PIC MCU devices do not support partial program memory erase; therefore, users may experience slower performance than with other devices. Also, see either the in-circuit emulator or the in-circuit debugger Help file for information on specific device limitations that may affect performance.
DS51292S-page 5
Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. Technical support is available through the web site at: http://support.microchip.com. Documentation errors or comments may be emailed to docerrors@microchip.com.
DS51292S-page 6
Required Headers
Some devices have no built-in debug circuitry. Therefore, special ICE/ICD versions of these devices are required for debug tool operation. Currently available headers and their associated ICE/ICD devices are shown below by supported device. TABLE 1: REQUIRED HEADERS BY DEVICE
Device PIC10F200/2/4/6 PIC10F220/2 PIC12F508/509 PIC12F510 PIC12F519 PIC12F609/HV609 PIC12F615/HV615 PIC12F617 PIC12F629 PIC12F635 PIC12F675 PIC12F683 PIC16F505 PIC16F506 PIC16F526 PIC16F610/HV610 PIC16F616/HV616 PIC16F627A/628A PIC16F630 PIC16F631 PIC16F636 PIC16F639
(1)
Pin Count 8/14 8/14 8/14 8/14 8/14 28 28 28 8 14 8 8 8/14 8/14 8/14 14/16 14/16 18 14 20 14 20 18 14 20 14 20 14 20
Header Part Number AC162059 AC162070 AC162059 AC162070 AC162096 AC162083 AC162083 AC162083 AC162050 AC162057 AC162050 AC162058 AC162059 AC162070 AC162096 AC162083 AC162083 AC162053 AC162052 AC162061 AC162057 AC162066 AC162053 AC162052 AC162061 AC162055 AC162061 AC162056 AC162061
ICE/ICD Device Used PIC16F505-ICD PIC16F506-ICD PIC16F505-ICD PIC16F506-ICD PIC16F526-ICD PIC16F616-ICD PIC16F616-ICD PIC16F616-ICD PIC12F675-ICD PIC16F636-ICD PIC12F675-ICD PIC12F683-ICD PIC16F505-ICD PIC16F506-ICD PIC16F526-ICD PIC16F616-ICD PIC16F616-ICD PIC16F648A-ICD PIC16F676-ICD PIC16F690-ICD PIC16F636-ICD PIC16F636-ICD PIC16F648A-ICD PIC16F676-ICD PIC16F690-ICD PIC16F684-ICD PIC16F690-ICD PIC16F688-ICD PIC16F690-ICD
VDD Max 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V 5.5V
DS51292S-page 7
Required Headers
TABLE 1: REQUIRED HEADERS BY DEVICE (CONT)
Device PIC16F716 PIC16F785/HV785 PIC18F13K50 PIC18F14K50 PIC18LF13K50 PIC18LF14K50 PIC24F04KA200 PIC24F04KA201 Note 1: 2: 3: Pin Count 18 20 20 20 14 20 Header Part Number AC162054 AC162060 AC244023 AC244024 AC244028 ICE/ICD Device Used PIC16F716-ICD PIC16F785-ICD PIC18F14K50-ICE PIC18LF14K50-ICE PIC24F16KA102-ICE(3) VDD Max 5.5V 5.5V 5.5V 3.6V 2.75V(2) 3.6V
AC162050, AC162058
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify these header boards, use the following information.
Header AC162050 AC162058 ICE/ICD Device PIC12F675-ICD PIC12F683-ICD Board Assembly Number 02-01662
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target.
DS51292S-page 8
Required Headers
FIGURE 1: DIMENSIONS AC162050, AC162058
1.000 0.525
J2
Top
Side
0.062 Typical
DS51292S-page 9
Required Headers
AC162052, AC162055, AC162056, AC162057
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify these header boards, use the following information.
Header AC162052 AC162055 AC162056 AC162057 ICE/ICD Device PIC16F676-ICD PIC16F684-ICD PIC16F688-ICD PIC16F636-ICD Board Assembly Number 02-01686
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
DS51292S-page 10
Required Headers
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target. FIGURE 2: DIMENSIONS AC162052, AC162055, AC162056, AC162057
1 P1
J1
1.300 0.825
J2
Top
Side
0.062 Typical
DS51292S-page 11
Required Headers
AC162053, AC162054
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify these header boards, use the following information.
Header AC162053 AC162054 ICE/ICD Device PIC16F648A-ICD PIC16F716-ICD Board Assembly Number 02-01695
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
DS51292S-page 12
Required Headers
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target. FIGURE 3: DIMENSIONS AC162053, AC162054
0.150 0.150
1 P1
0.750
2.350
Top
0.062 Typical
Side
DS51292S-page 13
Required Headers
AC162059, AC162070, AC162096
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify these header boards, use the following information.
Header AC162059 AC162070 AC162096 ICE/ICD Device PIC16F505-ICD PIC16F506-ICD PIC16F526-ICD Board Assembly Number 02-01803
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
DS51292S-page 14
Required Headers
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target. FIGURE 4: DIMENSIONS AC162059, AC162070, AC162096
14-Pin Target Pin 1 Located on Bottom side of Header 8-Pin Target Pin 1 Located on Bottom side of Header
0.450 0.225
0.750
U1
1.200 2.250
Top
0.062 Typical
Side
DS51292S-page 15
Required Headers
AC162060
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify this header board, use the following information.
Header AC162060 ICE/ICD Device PIC16F785-ICD Board Assembly Number 02-01820
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
DS51292S-page 16
Required Headers
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target. FIGURE 5: DIMENSIONS AC162060
J1
J2
U1
0.750
2.250
Top
0.062 Typical
Side
DS51292S-page 17
Required Headers
AC162061
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify this header board, use the following information.
Header AC162061 ICE/ICD Device PIC16F690-ICD Board Assembly Number 02-01835
ON
DIP
10 9 8 7 6 S1 1 2 3 4 5
S1
ON
1
ECCP
2
SSP
3
USART
4
4KPFM
5
ADC
Switch configuration at left shows all peripherals disabled, which is the setting to select the PIC16F631 device.
ENABLE
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
DS51292S-page 18
Required Headers
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target. FIGURE 7: DIMENSIONS AC162061
1.450
0.475
Top
0.062 Typical
Side
DS51292S-page 19
Required Headers
AC162066
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify this header board, use the following information.
Header AC162066 ICE/ICD Device PIC16F636-ICD Board Assembly Number 02-01832
In addition to being used with debug tools that normally use headers, this header is used with the PCM16YM0 processor module to emulate a PIC16F639 on the MPLAB ICE 2000 in-circuit emulator. Plug the end of the processor module into the header, and then plug the header into the transition socket or directly onto the target board.
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
DS51292S-page 20
Required Headers
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target. FIGURE 8: DIMENSIONS AC162066
Top
0.062 Typical
Side
DS51292S-page 21
Required Headers
AC162083
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify this header board, use the following information.
Header AC162083 ICE/ICD Device PIC16F616-ICD Board Assembly Number 02-01976
CAUTION
Incorrect rotary switch (Figure 9) settings may irreparably damage the header. Ensure rotary switch settings are correct (Table 3) before powering or connecting the header. Do not change the rotary switch setting while the header is powered or connected to a debug tool. Do not power shunt regulator (HV) devices from the debug tool.
Test points are available on this header to check the following: Ground (TP1), VDD (TP2), ICD Clock (TP3), ICD Data (TP4) and ICD MCLR/VPP (TP5). TABLE 3: ROTARY SWITCH SETTINGS
Switch Position 0 1 2 3 4 5 6 7 Device PIC12HV609 PIC12HV615 Reserved HV PIC16HV610 PIC16HV616 Reserved HV Reserved HV Reserved HV Switch Position 8 9 A B C D E F Device PIC12F609 PIC12F615 PIC12F617 PIC16F610 PIC16F616 Reserved F Reserved F Reserved F
POTENTIAL ISSUES HV device selected instead of F device If you inadvertently select a shunt regulator (HV) device and attempt to use it in a target board designed for a non-shunt regulator (F) device, the shunt may draw excessive current due to the lack of current-limiting circuitry on the target board and damage the device mounted on the header. F device selected instead of HV device If you inadvertently select a non-shunt regulator (F) device and attempt to use it in a target board designed for a shunt regulator (HV) device, the device may draw excessive current due to the higher voltage used on a target board designed for HV devices and damage the device mounted on the header. HV devices cannot be powered from debug tool Do not select in MPLAB IDE to power the target (debug header) from the debug tool (if it supports powering the target) when using shunt regulator (HV) devices since this will also cause the shunt to draw excessive current.
DS51292S-page 22
Required Headers
DETERMINING DAMAGE A damaged header will cause MPLAB IDE to report a device ID of 0. However, there are other issues that can cause the device ID to report as 0. Please consult your debug tool documentation on troubleshooting to identify the problem. If you believe you have a damaged header, please contact Microchip technical support at http://support.microchip.com.
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target. FIGURE 9: DIMENSIONS AC162083
0.650
6 Conductor Modular Cable Target Pin 1 Located on Bottom side of Header Use for Both 14-pin and 8-pin Device Alignment 2.450
1.600
Top
0.062 Typical
Side
DS51292S-page 23
Required Headers
AC244023, AC244024
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify these header boards, use the following information.
Header AC244023 AC244024 ICE/ICD Device PIC18F14K50-ICE PIC18LF14K50-ICE Board Assembly Number 02-02031
To MPLAB ICD
To Target Board
R2 10k 1%
R3 24k 1%
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
DS51292S-page 24
Required Headers
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target. FIGURE 11: DIMENSIONS AC244023, AC224024
0.150
1.150
0.425 1.800
Top
0.165 Typical
Side
DS51292S-page 25
Required Headers
AC244028
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify this header board, use the following information.
Header AC244028 ICE/ICD Device PIC24F16KA102-ICE Board Assembly Number 02-02107
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
DS51292S-page 26
Required Headers
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target. FIGURE 12: DIMENSIONS AC244028
0.280 1.860
2.370 Optional SPI trace 2-Pin right angle header to be installed here. (Digi-Key P/N A32702-02-ND)
Top
0.165 Typical
Side
0.165 Typical
DS51292S-page 27
Required Headers
NOTES:
DS51292S-page 28
Optional Headers
Devices that have built-in debug circuitry do not require a header to use debug tools. However, some pins and memory must be used to support the debug function. Special ICE/ICD versions offering additional pins, memory and emulator functions can be used to provide superior emulating/debugging capabilities. Currently available headers and their associated ICE/ICD devices are shown below by supported device. TABLE 1: OPTIONAL HEADERS BY DEVICE
Device PIC16F722 PIC16F723 PIC16F724 PIC16F726 PIC16F727 PIC16LF722 PIC16LF723 PIC16LF724 PIC16LF726 PIC16LF727 PIC18F1230/1330 PIC18F13K22 PIC18F14K22 PIC18LF13K22 PIC18LF14K22 PIC18F24J10 PIC18F25J10 PIC18LF24J10 PIC18LF25J10 PIC18F44J10 PIC18F45J10 PIC18LF44J10 PIC18LF45J10 PIC18F44J10 PIC18F45J10 PIC18LF44J10 PIC18LF45J10 Note 1: 2: VDDCORE Max Header required for other devices. 44 AC162074 PIC18F45J10-ICE Pin Count 28 28 40/44 28 40/44 28 28 40/44 28 40/44 28 20 20 28/40 Header Part Number AC244026 ICE/ICD Device Used PIC16F727-ICE VDD Max 5.5V
AC244027
PIC16LF727-ICE
3.6V
5.5V 5.5V 3.6V 2.75V(1) 3.6V 3.6V 2.75V(1) 3.6V 3.6V 2.75V(1) 3.6V 3.6V 2.75V(1)
DS51292S-page 29
Optional Headers
TABLE 1: OPTIONAL HEADERS BY DEVICE (CONT)
Device PIC18F63J11 PIC18F63J90 PIC18F64J11 PIC18F64J16 PIC18F64J90 PIC18F64J95 PIC18F65J11 PIC18F65J90 PIC18F83J11 PIC18F83J90 PIC18F84J11 PIC18F84J16 PIC18F84J90 PIC18F84J95 PIC18F85J11 PIC18F85J90 PIC18F65J10 PIC18F65J15 PIC18F66J10 PIC18F66J15 PIC18F67J10 PIC18F85J10 PIC18F85J15 PIC18F86J10 PIC18F86J15 PIC18F87J10 PIC18F65J16 PIC18F66J11 PIC18F66J16 PIC18F67J11 PIC18F85J16 PIC18F86J11 PIC18F86J16 PIC18F87J11 PIC18F65J50 PIC18F65J55 PIC18F66J50 PIC18F66J55 PIC18F67J50 64/80 AC162087 PIC18F87J50-ICE 3.6V 64/80 AC162091 PIC18F87J11-ICE 3.6V 64/80 AC162062 PIC18F87J10-ICE 3.6V Pin Count 64/80 Header Part Number AC162079 ICE/ICD Device Used PIC18F85J90-ICE VDD Max 3.6V
PIC18F85J50 PIC18F85J55 PIC18F86J50 PIC18F86J55 PIC18F87J50 Note 1: VDDCORE Max 2: Header required for other devices.
DS51292S-page 30
Optional Headers
TABLE 1: OPTIONAL HEADERS BY DEVICE (CONT)
Device PIC18F66J60 PIC18F66J65 PIC18F67J60 PIC18F86J60 PIC18F86J65 PIC18F87J60 PIC18F96J60 PIC18F96J65 PIC18F97J60 PIC24F08KA101 PIC24F08KA102 PIC24F16KA101 PIC24F16KA102 PIC24FJ16GA002 PIC24FJ32GA002 PIC24FJ48GA002 PIC24FJ64GA002 PIC24FJ16GA004 PIC24FJ32GA004 PIC24FJ48GA004 PIC24FJ64GA004 PIC24FJ64GA006 PIC24FJ64GA008 PIC24FJ64GA010 PIC24FJ96GA006 PIC24FJ96GA008 PIC24FJ96GA010 PIC24FJ128GA006 PIC24FJ128GA008 PIC24FJ128GA010 Note 1: VDDCORE Max 2: Header required for other devices. 20/28 AC244028 PIC24F16KA102-ICE(2) 3.6V Pin Count 64/80/ 100 Header Part Number AC162064 ICE/ICD Device Used PIC18F97J60-ICE VDD Max 3.6V
28
AC162088
PIC24FJ64GA004-ICE
3.6V
44
AC162094
64/80/ 100
AC162065 or AC244022
PIC24FJ128GA010-ICE
3.6V
DS51292S-page 31
Optional Headers
AC162062, AC162079, AC162087, AC162091
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify these header boards, use the following information.
Header AC162062 AC162079 AC162087 AC162091 ICE/ICD Device PIC18F87J10-ICE PIC18F85J90-ICE PIC18F87J50-ICE PIC18F87J11-ICE Board Assembly Number 02-01830
CAUTION
This header cannot be plugged directly into the PICDEM HPC Explorer Board or device damage will result.
The PICDEM HPC Explorer Board is 5V, whereas the ICD device on the header is 3.6V max. Therefore, modification to the demo board is necessary before the header can be used. 1. Switch S3 should be set to ICE. 2. Jumper J2 must be connected as shown in Figure 1 to modify the operating voltage. See demo board documentation for more information. FIGURE 1: DEMO BOARD J2 CONNECTIONS
pin1 For V = 3.3V: R = 1.18 k (1%) +5V ADJ VIN J2 R
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
DS51292S-page 32
Optional Headers
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target. FIGURE 2: DIMENSIONS AC162062, AC162079, AC162087, AC162091
1.080
0.980
2.325
0.050
Top
0.062 Typical
Side
DS51292S-page 33
Optional Headers
AC162064
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify this header board, use the following information.
Header AC162064 ICE/ICD Device PIC18F97J60-ICE Board Assembly Number 02-01853
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
DS51292S-page 34
Optional Headers
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target. FIGURE 3: DIMENSIONS AC162064
0.555
0.455
0.355
1.750
Top
0.062 Typical
Side
DS51292S-page 35
Optional Headers
AC162065, AC244022
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify these header boards, use the following information.
Header AC162065 AC244022 ICE/ICD Device PIC24FJ128GA010-ICE Board Assembly Number 02-01856 02-01985
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
Header Dimensions
The figures below lists the dimensions for the header boards. Dimensions are design values in inches. For this device family, header AC162065 will be sold until depleted. Then only header AC244022 will remain as a Performance Pak. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target.
DS51292S-page 36
Optional Headers
FIGURE 4: DIMENSIONS AC162065
0.555
0.455
0.355
1.750
Top
0.062 Typical
Side
DS51292S-page 37
Optional Headers
FIGURE 5: DIMENSIONS AC244022
0.525
0.425
0.325
1.850
Target Pin 1 Located on Bottom side of Header 8 Conductor Single In-line Debugger Interface
Top
0.335 Typical
Side
DS51292S-page 38
Optional Headers
AC162067, AC162074
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify these header boards, use the following information.
Header AC162067 AC162074 ICE/ICD Device PIC18F45J10-ICE Board Assembly Number 02-01854 02-01929
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
Header Dimensions
The figures below lists the dimensions for the header boards. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target.
DS51292S-page 39
Optional Headers
FIGURE 6: DIMENSIONS (28/40-PIN) AC162067
0.700
0.850
1.800
Top
0.062 Typical
Side
DS51292S-page 40
Optional Headers
FIGURE 7: DIMENSIONS (44-PIN) AC162074
1.350
0.850 1.800
Top
0.062 Typical
Side
DS51292S-page 41
Optional Headers
AC162078
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify this header board, use the following information.
Header AC162078 ICE/ICD Device PIC18F1330-ICD Board Assembly Number 02-01896
DS51292S-page 42
Optional Headers
PICDEM MC/MC LV MOTOR CONTROL DEMO BOARDS To run a BLDC motor on the PICDEM MC board or PICDEM MC LV board using the supplied firmware, use the following jumper setup:
Jumper J1 J2 J3 J5 J6 J7 Jumper Setting 2-3 2-3 2-3 2-3 1-2 1-2 Jumper JP1 JP2 JP3 Jumper Setting Open Open Open
S1 is not populated and should not be used. After the header board is set up, do the following: 1. 2. 3. 4. 5. 6. Connect the header to the PICDEM MC/MC LV target board. Power the target board. You should see the red LED on the header board turn on. Connect the debug tool to the header board. Program the part with the demo code. Run the program. Press and release switch S2 on the target board to toggle the direction of the motors rotation. 7. Press and release switch S1 on the target board to toggle between running and stopping the motor. 8. If the motor stops while reversing from a high speed, there could be an overcurrent condition detected by the system. Reset the system to run the program again.
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
DS51292S-page 43
Optional Headers
Header Dimensions
The figure below lists the dimensions for the header board. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target. FIGURE 8: DIMENSIONS AC162078
28-Pin Target Pin 1 Located on Bottom side of Header 18-Pin Target Pin 1 Located on Bottom side of Header
2.300
0.950
M
0.300 0.150 2.050
0.410
Top
0.062 Typical
Side
DS51292S-page 44
Optional Headers
AC162088, AC162094
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify this header board, use the following information.
Header AC162088 AC162094 ICE/ICD Device PIC24FJ64GA004-ICE Board Assembly Number 02-01979 02-01982
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
Header Dimensions
The figures below list the dimensions for the header boards. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target.
DS51292S-page 45
Optional Headers
FIGURE 9: DIMENSIONS (28 PIN) AC162088
1.600
0.700
0.175 2.450
Top
0.165 Typical 0.560 Typical
0.062 Typical
Side
DS51292S-page 46
Optional Headers
FIGURE 10: DIMENSIONS (44 PIN) AC162094
1.600
0.550
0.400 2.400
Top
0.062 Typical
Side
DS51292S-page 47
Optional Headers
AC244026, AC244027
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify this header board, use the following information.
Header AC244026 AC244027 ICE/ICD Device PIC16F727-ICE PIC16LF727-ICE Board Assembly Number 02-02105
This header has jumpers available for MCLR pull-up and power LED control.
Jumper J2 Setting Open Short Function Disable weak ICE MCLR pull-up resistor. Enable weak ICE MCLR pull-up resistor. This option keeps the target program running even after the tool has been disconnected from the header, i.e., the pin will not float high. Disable power LED indicator. This option saves power. Enable power LED indicator.
J3
Open Short
Additionally, this header has jumpers related to the LDO voltage regulator. Depending on the device pin used for this function, you would use either J4 (RA0), J5 (RA5) or J6 (RA6) for Vcap selection. For details on the voltage regulator, see the PIC16F72X/PIC16LF72X Data Sheet (DS41341).
Jumper J4 or J5 or J6 Setting Open Short Function Use only target capacitance for VCAP. This is the standard configuration. Use both on-board and target capacitance for VCAP. This option is to provide extra margin for the voltage regulator stability/regulation in cases where there is a long lead length between the emulation header VCAP pin and the target VCAP pin. (As examples, when using long-pin DIP transition sockets or certain QFN transition sockets.)
DS51292S-page 48
Optional Headers
Test points are available on this header to check the following:
Test Point TP1 TP2 TP3 TP4 TP5 Vss VDD ICD Enable VDD Vss Signal Test Point TP6 TP7 TP8 Signal Vcap Vcap Vcap RA0 RA5 RA6 Pin J4 J5 J6 Jumper
This header has jumpers available for MCLR pull-up and power LED control.
Jumper J2 Setting Open Short Function Disable weak ICE MCLR pull-up resistor. Enable weak ICE MCLR pull-up resistor. This option keeps the target program running even after the tool has been disconnected from the header, i.e., the pin will not float high. Disable power LED indicator. This option saves power. Enable power LED indicator.
J3
Open Short
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
Header Dimensions
The figures below list the dimensions for the header boards. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target.
DS51292S-page 49
Optional Headers
FIGURE 11: DIMENSIONS AC244026, AC244027
0.710
0.345 TQFP 6 Conductor Single In Line Debugger Interface Optional SPI trace 2-Pin right angle header to be installed here. (Digi-Key P/N: A32702-02-ND)
QFN 0.840
0.710 2.575 44-Pin QFN Target Pin 1 located on Bottom side of Header 28-Pin DIP Target Pin 1 located on Bottom side of Header
Top
0.380 Typical 0.062 Typical
0.165 Typical
Side
0.335 Typical
DS51292S-page 50
Optional Headers
AC244033, AC244034
Header Identification
The header AC number is used for ordering the header. However, this number is not on the header board, as the board is often used for multiple headers by inserting different ICE/ICD devices. To identify this header board, use the following information.
Header AC244033 AC244034 ICE/ICD Device PIC18F14K22-ICE PIC18LF14K22-ICE Board Assembly Number 02-02031
Header Limitations
See the Limitations section in your debug tool on-line Help file for details.
Header Dimensions
The figures below list the dimensions for the header boards. Dimensions are design values in inches. If the length and/or width of the header board is too large a footprint for the target board, consider using stand-offs, transition sockets or other extenders in the header connection socket to raise the header above the target.
DS51292S-page 51
Optional Headers
FIGURE 12: DIMENSIONS (20 PIN) AC244033, AC244034
0.150
1.150
0.425 1.800
Top
0.165 Typical
Side
DS51292S-page 52
0.100
0.800 0.050
0.800
DS51292S-page 53
FIGURE 15:
Header pin-out matches the PLCC package. PLCC will map to TQFP as follows: FIGURE 16: Header to 44-pin TQFP one-to-one mapping. Header to 64-pin TQFP see Figure 16 for mapping. Header to 80-pin TQFP see Figure 17 for mapping. Header to 100-pin TQFP one-to-one mapping.
NC = No Connection 68 1 1 60 NC 52 51 48
NC
NC
43
16
17 18
NC 26 34
35
33
17
32
DS51292S-page 54
FIGURE 17:
NC = No Connection 84 1 1 74 NC 64 63 60
11
NC
NC
53
20
21 22
NC 32 42
43
41
21
40
DS51292S-page 55
NOTES:
DS51292S-page 56
DS51292S-page 57
Header Connector
MPLAB REAL ICE in-circuit emulator High-Speed Receiver Board or optional Isolation Unit
DS51292S-page 58
PICkit 2 or 3 Debug Express Using the Modular-to-SIL Adapter, you can also connect to: MPLAB REAL ICE in-circuit emulator (Standard Communication) MPLAB ICD 2 or 3 FIGURE 3: 6-PIN SIL CONNECTION TOP TOP
J1 1 1 J3 DAT CLK J2
Header Connector
MPLAB REAL ICE in-circuit emulator High-Speed Receiver Board or optional Isolation Unit TOP
1 1
TOP
it k C PI
PICkit 2 or 3
Header Connector
DS51292S-page 59
MODULAR-TO-SIL ADAPTER
To adapt a 6-pin modular connector to an 8-pin SIL (Single In-Line) connector, you can use this adapter. You can also use this adapter for a 6-pin modular connector to an 6-pin SIL connector. In either case, line up pin 1 of J1 with pin 1 of the 6- or 8-pin header connector. FIGURE 4: MODULAR-TO-SIL ADAPTER CONNECTION TOP TOP From Tool TOP
J2 1 J1 1
Modular Connector
J2 1 2 3 4 5 6 ICRST VDD ICDT ICCK NC
SIL Connector
J1 1 2 3 4 5 6 7 8 ICRST VDD ICDT ICCK NC
ORDERING INFORMATION
To order the development tools and other hardware shown here, please refer to the table below. TABLE B-1:
MPLAB REAL ICE in-circuit emulator (Standard Communication) MPLAB REAL ICE in-circuit emulator (High-Speed Communication) Performance Pak MPLAB REAL ICE Isolation Unit (works with High-Speed Communication) MPLAB ICD 2 MPLAB ICD 3 PICkit 2 Debug Express PICkit 3 Debug Express Modular-to-SIL Adapter
DS51292S-page 60
REVISION HISTORY
Added Appendix A: Revision History Updated document to reflect support of additional tools Additional minor corrections throughout document text
C.2
Updated document to reflect support of additional tools Additional minor corrections throughout document text
C.3
Added limitations to header setup sections as needed. Changed ICD Headers and ICE Headers to Required Headers and Optional Headers and move sections as necessary. Rearranged sections to organize by header (AC) number.
C.4
Added board dimensions Removed header pinouts Added board identification info Added why use a header section Added footprint appendix Changed MPLAB ICD 2 and MPLAB ICD 3 references to generic debug tool Added MPLAB REAL ICE in-circuit emulator and MPLAB ICD 3 as programmers
C.5
Added AC244028 Added Header Connections chapter Added AC244033, AC244034 Moved limitations to common Limitations file and added small section referencing Help files Added PIC12F617 to AC162083
DS51292S-page 61
DS51292S-page 62
M
Modular Connector................................................... 57 Modular-to-SIL Adapter............................................ 60 MPLAB ICE 2000 ..................................................... 20
A
AC162050 .................................................................. 8 AC162052 ................................................................ 10 AC162053 ................................................................ 12 AC162054 ................................................................ 12 AC162055 ................................................................ 10 AC162056 ................................................................ 10 AC162057 ................................................................ 10 AC162058 .................................................................. 8 AC162059 ................................................................ 14 AC162060 ................................................................ 16 AC162061 ................................................................ 18 AC162062 ................................................................ 32 AC162064 ................................................................ 34 AC162065 ................................................................ 36 AC162066 ................................................................ 20 AC162067 ................................................................ 39 AC162070 ................................................................ 14 AC162074 ................................................................ 39 AC162078 ................................................................ 42 AC162079 ................................................................ 32 AC162083 ................................................................ 22 AC162087 ................................................................ 32 AC162088 ................................................................ 45 AC162091 ................................................................ 32 AC162094 ................................................................ 45 AC162096 ................................................................ 14 AC244022 ................................................................ 36 AC244023 ................................................................ 24 AC244024 ................................................................ 24 AC244026 ................................................................ 48 AC244027 ................................................................ 48 AC244028 ................................................................ 26 AC244033 ................................................................ 51 AC244034 ................................................................ 51 Additional Information ................................................ 5
O
Ordering Hardware................................................... 60
P
PCM16YM0.............................................................. 20 Performance............................................................... 5 PIC10F200 ................................................................. 7 PIC10F202 ................................................................. 7 PIC10F204 ................................................................. 7 PIC10F206 ................................................................. 7 PIC10F220 ................................................................. 7 PIC10F222 ................................................................. 7 PIC12F508 ................................................................. 7 PIC12F509 ................................................................. 7 PIC12F510 ................................................................. 7 PIC12F519 ................................................................. 7 PIC12F609 ........................................................... 7, 22 PIC12F615 ........................................................... 7, 22 PIC12F617 ........................................................... 7, 22 PIC12F629 ............................................................. 7, 8 PIC12F635 ........................................................... 7, 10 PIC12F675 ............................................................. 7, 8 PIC12F683 ............................................................. 7, 8 PIC12HV609 ........................................................ 7, 22 PIC12HV615 ........................................................ 7, 22 PIC16F505 ................................................................. 7 PIC16F506 ................................................................. 7 PIC16F526 ................................................................. 7 PIC16F610 ........................................................... 7, 22 PIC16F616 ........................................................... 7, 22 PIC16F627A......................................................... 7, 12 PIC16F628A......................................................... 7, 12 PIC16F630 ........................................................... 7, 10 PIC16F631 ........................................................... 7, 18 PIC16F636 ........................................................... 7, 10 PIC16F639 ........................................................... 7, 20 PIC16F648A......................................................... 7, 12 PIC16F676 ........................................................... 7, 10 PIC16F677 ........................................................... 7, 18 PIC16F684 ........................................................... 7, 10 PIC16F685 ........................................................... 7, 18 PIC16F687 ........................................................... 7, 18 PIC16F688 ........................................................... 7, 10 PIC16F689 ........................................................... 7, 18 PIC16F690 ........................................................... 7, 18 PIC16F716 ........................................................... 8, 12 PIC16F785 ........................................................... 8, 16
C
Calibration Bits ........................................................... 5
I
ICE vs. ICD ................................................................ 2
J
Jumper Settings 8, 10, 16, 20, 26, 32, 39, 43, 45, 48, 49
DS51292S-page 63
S
SIL Connector, 6 Pin ................................................ 59 SIL Connector, 8 Pin ................................................ 58 Switch Settings......................................................... 18 Switch Settings, Rotary ............................................ 22
T
Transition Socket........................................................ 4
V
Vdd Max ............................................................... 7, 29 Vddcore Max ........................................................ 7, 29
DS51292S-page 64
Note the following details of the code protection feature on Microchip devices: Microchip products meet the specification contained in their particular Microchip Data Sheet. Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchips Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. Microchip is willing to work with the customer who is concerned about the integrity of their code. Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as unbreakable.
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchips code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyers risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights.
Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Octopus, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. 2010, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper.
ISBN: 978-1-60932-377-6
Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Companys quality system processes and procedures are for its PIC MCUs and dsPIC DSCs, KEELOQ code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchips quality system for the design and manufacture of development systems is ISO 9001:2000 certified.
DS51292S-page 65
ASIA/PACIFIC
Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049
ASIA/PACIFIC
India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350
EUROPE
Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820
01/05/10
DS51292S-page 66