Professional Documents
Culture Documents
www.huawei.com
DBS3900 Abbreviations
WMPT WBBPbD UBFA UELP UFLP UPEU CPRI APM WCDMA Main Processing and Transmission Unit WCDMA Baseband Process unit Type D Universal BBU Fan Unit Type A (2U) Universal E1/T1 Lighting Protection unit Universal FE/GE Lighting Protection unit Universal Power and Environment Interface Unit Common Protocol Radio Interface Advanced Power Module (FOR OUTDOOR)
Page 2
DBS3900 Overview
DBS3900 system consists of:
BBU3900/BBU3806 Baseband Unit RRU3804 /RRU38008 /RRU3801 Remote Radio Unit Antenna and feeder system
Antenna
Feeder
Grounding cable
Power cable
BBU3900
RF jumper
Page 3
BBU3900 Module
Typical configuration
BBU3806 Module
UPEU
The optional boards are the UELP, UFLP, UTRP, and UEIU.
All rights reserved Page 4
Page 5
Page 6
LED RUN
Color Green
ON OFF
Status
Description
The BBU3806 is checking the version, or it is faulty. The BBU3806 has no power input, or it is faulty. The BBU3806 runs properly. Software is being loaded to the BBU3806, or the BBU3806 is not configured. The hardware of the BBU3806 is faulty. The hardware of the BBU3806 runs properly. An external port on the BBU3806 is faulty. The BBU3806 is running or in the active state. The board is not in use or the working mode of the BBU3806 is extension. A local E1/T1 alarm is generated. A remote E1/T1 alarm is generated. This link is not used, or the alarm is cleared. The CPRI link is faulty. The CPRI link and the hardware of the RRU run properly. A VSWR alarm is generated. The hardware of the RRU is faulty.
ON for 1s and OFF for 1s ON for 0.25s and OFF for 0.25s
ALM
Red
ON OFF Blinking
ACT
Green
ON OFF
LIU0 to LIU7
Yellow
ON ON for 0.25s and OFF for 0.25s OFF ON OFF ON for 1s and OFF for 1s ON for 0.125s and OFF for 0.125s
CPRI 0 to CPRI 2
Yellow
Page 7
Appearance The -48 V DC cable has a 7W2 female connector at one end and two bare power wires at the other end, as shown in Figure 1. OT terminals or cord end terminals must be added to the two wires on site.
Description The two wires are used to transmit -48 V power signals.
Page 8
Page 9
(2) OT terminal
Page 10
Slot
16
SLOT0
SLOT1 SLOT2 SLOT3
SLOT4
SLOT5 SLOT6
Slot 18
B
F
WBBP
WBBP
UTRP
UTRP
PEU/
EIU
Slot 19
WBBP WBBP
WMPT
WMPT
PEU/
EIU
SLOT7
Page 11
4E1:DB26
Board number
maximum is 2 for one BBU mandatory board working in active and standby mode
Providing OM channels
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 12
Label RUN
Color Green
Description The board has power input, yet the board is faulty. The board has no power input. The board is running as configured. The software is being loaded to the board, or the board is not in use. The board is reporting alarms and is faulty. The board is running properly. The external ports of the board are faulty. The board is in active mode. The board is in standby mode.
ALM
Red
ON OFF Blinking
ACT
Green
ON OFF
Page 13
LED
Color
Status
Description
Green
ON
OFF
Yellow
Blinking OFF
Green
ON OFF
Yellow
Blinking
OFF
Page 14
SW1 for setting the E1/T1 working mode SW2 for setting the protection ground for the E1.
Settings of SW1 Bit T1 Mode 120-ohm E1 Balanced Mode OFF OFF 75-ohm E1 Unbalanced Mode ON ON
1 2
ON ON
3
4
OFF
OFF
ON
ON
ON
ON
Settings of SW2
Bit
Description
1 2 3 4
Page 15
Page 16
Page 17
Page 18
Page 19
Blinking at 0.5 Hz
The RRU on the CPRI link is faulty in the antenna system connection.
Page 20
Board
WBBPa
WBBPb1
WBBPb2 WBBPb3 WBBPb4 WBBPd1 WBBPd2 WBBPd3
3
3 6 6 6 6 6
64
128 256 384 192 384 256
64
128 256 384 192 384 256
Page 21
Page 22
-48V to +12V
+24V to +12V
Board number mandatory, maximum is 2, 1+1 backup Main Functions Converting -48 V or +24 V DC power input to +12 V DC power that is supported by boards
Page 23
Label RUN
Color Green
Status ON OFF
Description The board is running properly. The board has no power input, or the board is faulty.
Socket and Port: The UPEU has one socket and four ports.
Page 24
Page 25
Thank You
www.huawei.com