Professional Documents
Culture Documents
A741, A741Y General-Purpose Operational Amplifiers: Description
A741, A741Y General-Purpose Operational Amplifiers: Description
Short-Circuit Protection Offset-Voltage Null Capability Large Common-Mode and Differential Voltage Ranges No Frequency Compensation Required Low Power Consumption No Latch-Up Designed to Be Interchangeable With Fairchild A741
NC NC OFFSET N1 IN IN + VCC NC
1 2 3 4 5 6 7
14 13 12 11 10 9 8
description
The A741 is a general-purpose operational amplifier featuring offset-voltage null capability. The high common-mode input voltage range and the absence of latch-up make the amplifier ideal for voltage-follower applications. The device is short-circuit protected and the internal frequency compensation ensures stability without external components. A low value potentiometer may be connected between the offset null inputs to null out the offset voltage as shown in Figure 2. The A741C is characterized for operation from 0C to 70C. The A741I is characterized for operation from 40C to 85C.The A741M is characterized for operation over the full military temperature range of 55C to 125C.
OFFSET N1 IN IN + VCC
1 2 3 4
8 7 6 5
NC OFFSET N1 IN IN + VCC
1 2 3 4 5
10 9 8 7 6
symbol
OFFSET N1 IN + IN OFFSET N2 + OUT A741M . . . FK PACKAGE (TOP VIEW)
NC IN NC IN + NC
4 5 6 7 8
3 2 1 20 19 18 17 16 15 14 9 10 11 12 13
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
NC VCC NC OFFSET N2 NC
5957
AVAILABLE OPTIONS PACKAGED DEVICES TA 0C to 70C 40C to 85C 55C to 125C SMALL OUTLINE (D) uA741CD uA741ID uA741MFK uA741MJ uA741MJG CHIP CARRIER (FK) CERAMIC DIP (J) CERAMIC DIP (JG) PLASTIC DIP (P) uA741CP uA741IP uA741MU TSSOP (PW) uA741CPW FLAT PACK (U) CHIP FORM (Y) uA741Y
The D package is available taped and reeled. Add the suffix R (e.g., uA741CDR).
schematic
VCC+
IN
OUT IN+
OFFSET N1 OFFSET N2
VCC
5958
(7)
(6)
IN + IN
(3) (2)
(8)
OFFSET N1 OFFSET N2
(1) (5)
45
(5)
(1)
(4)
(2)
36
(3)
5959
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
A741C Supply voltage, VCC+ (see Note 1) Supply voltage, VCC (see Note 1) Differential input voltage, VID (see Note 2) Input voltage, VI any input (see Notes 1 and 3) Voltage between offset null (either OFFSET N1 or OFFSET N2) and VCC Duration of output short circuit (see Note 4) Continuous total power dissipation Operating free-air temperature range, TA Storage temperature range Case temperature for 60 seconds Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds FK package J, JG, or U package 0 to 70 65 to 150 18 18 15 15 15 unlimited A741I 22 22 30 15 0.5 unlimited 40 to 85 65 to 150 A741M 22 22 30 15 0.5 unlimited 55 to 125 65 to 150 260 300 C C C C UNIT V V V V V
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds D, P, or PW package 260 260 C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, unless otherwise noted, are with respect to the midpoint between VCC+ and VCC . 2. Differential voltages are at IN+ with respect to IN . 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less. 4. The output may be shorted to ground or either power supply. For the A741M only, the unlimited duration of the short circuit applies at (or below) 125C case temperature or 75C free-air temperature. DISSIPATION RATING TABLE PACKAGE D FK J JG P PW U TA 25C POWER RATING 500 mW 500 mW 500 mW 500 mW 500 mW 525 mW 500 mW DERATING FACTOR 5.8 mW/C 11.0 mW/C 11.0 mW/C 8.4 mW/C N/A 4.2 mW/C 5.4 mW/C DERATE ABOVE TA 64C 105C 105C 90C N/A 25C 57C TA = 70C POWER RATING 464 mW 500 mW 500 mW 500 mW 500 mW 336 mW 432 mW TA = 85C POWER RATING 377 mW 500 mW 500 mW 500 mW 500 mW N/A 351 mW TA = 125C POWER RATING N/A 275 mW 275 mW 210 mW N/A N/A 135 mW
5960
All characteristics are measured under open-loop conditions with zero common-mode input voltage unless otherwise specified. Full range for the A741C is 0C to 70C, the A741I is 40C to 85C, and the A741M is 55C to 125C. NOTE 5: This typical value applies only at frequencies above a few hundred hertz because of the effects of drift and thermal feedback.
5961
electrical characteristics at specified free-air temperature, VCC = 15 V, TA = 25C (unless otherwise noted)
PARAMETER VIO VIO(adj) IIO IIB VICR VOM AVD ri ro Ci CMRR kSVS IOS ICC Input offset voltage Offset voltage adjust range Input offset current Input bias current Common-mode input voltage range Maximum peak output voltage swing Large-signal differential voltage amplification Input resistance Output resistance Input capacitance Common-mode rejection ratio Supply voltage sensitivity (VIO /VCC) Short-circuit output current Supply current VO = 0, VO = 0, No load VIC = VICRmin VCC = 9 V to 15 V 70 VO = 0, See Note 5 RL = 10 k RL = 2 k RL 2 k TEST CONDITIONS VO = 0 VO = 0 VO = 0 VO = 0 12 12 10 20 0.3 A741Y MIN TYP 1 15 20 80 13 14 13 200 2 75 1.4 90 30 25 1.7 150 40 2.8 200 500 MAX 6 UNIT mV mV nA nA V V V/mV M pF dB V/V mA mA
PD Total power dissipation No load 50 85 mW All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified. NOTE 5: This typical value applies only at frequencies above a few hundred hertz because of the effects of drift and thermal feedback.
5962
TEST CIRCUIT
APPLICATION INFORMATION
Figure 2 shows a diagram for an input offset voltage null circuit.
IN + IN OFFSET N1 10 k + OUT OFFSET N2
To VCC
5963
TYPICAL CHARACTERISTICS
VCC+ = 15 V VCC = 15 V
VCC+ = 15 V VCC = 15 V
0 60 40 20
20
40
60
0 60 40 20
20
40
60
TA Free-Air Temperature C
TA Free-Air Temperature C
Figure 3
MAXIMUM PEAK OUTPUT VOLTAGE vs LOAD RESISTANCE
14 VOM Maximum Peak Output Voltage V 13 12 11 10 9 8 7 6 5 4 0.1 0.2 0.4 0.7 1 2 4 7 VCC+ = 15 V VCC = 15 V TA = 25C
Figure 4
10
RL Load Resistance k
Figure 5
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
5964
TYPICAL CHARACTERISTICS
MAXIMUM PEAK OUTPUT VOLTAGE vs FREQUENCY
20 VOM Maximum Peak Output Voltage V 18 16 14 12 10 8 6 4 2 0 1k 10 k 100 k 1M VCC+ = 15 V VCC = 15 V RL = 10 k TA = 25C 400
200
100
40
20
Figure 6
OPEN-LOOP LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREQUENCY
107 106 105 104 103 102 101 1 10 1 1 100 10 k f Frequency Hz 1M 10 M VCC+ = 15 V VCC = 15 V VO = 10 V RL = 2 k TA = 25C
Figure 7
Figure 8
5965
TYPICAL CHARACTERISTICS
COMMON-MODE REJECTION RATIO vs FREQUENCY
100 CMRR Common-Mode Rejection Ratio dB 90 80 70 60 50 40 30 20 10 0 1 100 10 k f Frequency Hz 1M 100 M 4 0 0.5 1 t Time s VCC+ = 15 V VCC = 15 V BS = 10 k TA = 25C VO Output Voltage mV 28 24 20 16 12 8 4 10% 0 tr VCC+ = 15 V VCC = 15 V RL = 2 k CL = 100 pF TA = 25C 1.5 2 2.5
90%
Figure 9
VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE
8 6 Input and Output Voltage V 4 VO 2 0 VI 2 4 6 8 0 10 20 30 40 50 60 70 80 90 t Time s VCC+ = 15 V VCC = 15 V RL = 2 k CL = 100 pF TA = 25C
Figure 10
Figure 11
5966
IMPORTANT NOTICE Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied on is current. TI warrants performance of its semiconductor products and related software to the specifications applicable at the time of sale in accordance with TIs standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Certain applications using semiconductor products may involve potential risks of death, personal injury, or severe property or environmental damage (Critical Applications). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. Inclusion of TI products in such applications is understood to be fully at the risk of the customer. Use of TI products in such applications requires the written approval of an appropriate TI officer. Questions concerning potential risk applications should be directed to TI through a local SC sales office. In order to minimize risks associated with the customers applications, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein. Nor does TI warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used.