Professional Documents
Culture Documents
Install PNMT (WinXP)
Install PNMT (WinXP)
P N M T
ASOLINK
ETWORK
ANAGEMENT
ERMINAL
NEC Corporation
Copyright 2007
ROI-S05931
Table of Contents
1. 2. 3. 4. 5. 6. 7. Installation Sequence................................................................................................................1 Phone and Modem Options Setting (Standard 19.2Kbps Connection) ........................................2 Installation of USB Com Port Driver (USB Connection) ............................................................7 Dial-up Setting .......................................................................................................................10 SNMP Service Setting..............................................................................................................20 PNMT Setup ...........................................................................................................................26 Launching PNMT ...................................................................................................................31
-i-
ROI-S05931
1.
Installation Sequence
Only Administrator group privilege level users are authorized to configure the following settings, Step 1: Modem Setting
Network Element (NE) other than PASOLINK NEO Standard 19200bps Modem Setting (Phone and Modem Options Setting)
PASOLINK NEO ONLY USB Modem Setting (Installation of USB Com Port Driver)
-1-
ROI-S05931
2.
(2)
Click the Phone and Modem Options icon in the Control Panel window to start configuring the modem.
-2-
ROI-S05931
(3)
Enter your country and area code in the Location Information window. Click [OK].
(4)
-3-
ROI-S05931
(5)
Select the Modem tab. Click [Add] to continue with adding the new modem for the PNMT.
(6)
-4-
ROI-S05931
(7)
Select Standard Modem Types from the list of Manufacturers and Standard 19200bps Modem from the Models. Click [Next] to continue.
(8)
-5-
ROI-S05931
(9)
(10) Verify that Standard 19200 bps Modem and COM1 are displayed. Click [OK].
-6-
ROI-S05931
3.
(2)
Select Install from a list or specific location [Advanced] and click on [Next].
-7-
ROI-S05931
(3)
Insert the USB driver CD-ROM in the computers disk drive and select Search for the best driver in these locations and check Search removable media [floppy, CD-ROM ...] then, click [Next].
(4)
-8-
ROI-S05931
(5)
(6)
-9-
ROI-S05931
4.
Dial-up Setting
(1) Click Start | Settings | Control Panel and the Network Connections icon to start configuring the Dialup setting.
(2)
The Network Connections window appears. Click Create a new connection in the Network Tasks area.
- 10 -
ROI-S05931
(3)
The Welcome to the New Connection Wizard window appears. Click [Next].
(4)
- 11 -
ROI-S05931
(5)
(6)
Select Modem USB Modem Driver [COM#] and click [Next] to continue. NOTE This screen appears only when a USB Modem Driver has been installed.
- 12 -
ROI-S05931
(7)
In the New Connection Wizard window, enter Pnmt in the Company Name field and click [Next] to continue.
(8)
Enter any number in the Phone number field and click [Next] to continue.
- 13 -
ROI-S05931
(9)
Verify that Pnmt is displayed as the connection. You can also create a shortcut on your desktop if desired. Click [Finish].
(10) In the Connect Dial-up Connection window, click [Cancel] to continue. Click Properties in the Connect Dial-up Connection window.
- 14 -
ROI-S05931
(11) Verify that Modem-Standard 19200 bps Modem [COM1] is displayed on the General tab in the Dial-up Connection Properties window. Click [Configure].
- 15 -
ROI-S05931
(13) Retain the default setting on the Options tab and click the Security tab.
(14) Retain the default setting on the Security tab and click the Networking tab.
- 16 -
ROI-S05931
(15) On the Networking tab, verify that PPP ... is`displayed in the Type of dial-up server I am calling field and uncheck File and Printer ... and Client for Microsoft....
(16) Click Settings Uncheck all the boxes in the window that appears, as shown below. Click [OK] to go back to the previous window. Highlight Internet Protocol (TCP/IP) and then click [Properties].
- 17 -
ROI-S05931
(17) Verify that both Obtain an IP address automatically and Obtain DNS server address automatically are selected.
(18) In the Advanced TCP/IP Settings window, uncheck Use IP header compression for the PPP link. Click [OK].
- 18 -
ROI-S05931
(19) Retain the default setting on the Advanced tab and click [OK].
- 19 -
ROI-S05931
5.
(2) The Windows Components Wizard window appears. Remove the check from Management and Monitoring Tools, and then click Details ...
- 20 -
ROI-S05931
- 21 -
ROI-S05931
(3) The Management and Monitoring Tools window appears. Confirm that Simple Network Management Protocol is not checked and click [OK]. Return to above window and click [Next].
- 22 -
ROI-S05931
To Stop SNMP Service: (5) To stop SNMP Service without removing it, click Administrative Tools in the Control Panel window.
- 23 -
ROI-S05931
(7) Confirm that SNMP Service is installed and it has started automatically. Select Action Properties on the menu bar in the Services window, or right-click SNMP Service and then click Properties in the SNMP Service pop-up menu.
(8) Select Manual in the Startup type field and click Stop in the Service status field on the General tab. Click [OK] or [Apply].
- 24 -
ROI-S05931
(9) Confirm that the Status of both SNMP Service and SNMP Trap Service is stopped, and that the startup condition for each one is Manual.
- 25 -
ROI-S05931
6. PNMT Setup
NOTE If PNMT software has already been installed, please uninstall it before you install a new version. (1) Insert the PNMT Installation CDROM. Open the CDROM folder and double-click setupwin32.exe.
- 26 -
ROI-S05931
(4) Specify the directory in which the PNMT is to be installed. Click [Next].
NOTE The default path is C:\PNMTj. It is not possible to include blank spaces as in Program Files.
- 27 -
ROI-S05931
(5) Specify the License Key file if one is available. Click [Next].
NOTE If no License Key is available, operation in Trial mode is possible. Simply leave the License Key field blank and proceed.
IMPORTANT: IMMEDIATE IMPORT OF LICENSE You may use the PNMT on a trial basis for 30 days. After that the PNMT can ONLY be used IF the license has been imported (activated). To obtain the license please contact NEC.
- 28 -
ROI-S05931
(6) Specify the directory for storing PNMT log files. Click [Next].
NOTE The default path is <PNMTj Install Directory> when a Stored Directory is not specified. It is not possible to include blank spaces as in Program Files.
- 29 -
ROI-S05931
- 30 -
ROI-S05931
7.
Launching PNMT
(1) Click Start | Programs |PNMTj |PNMT to start the application.
(2) If he following window appears, select [Unblock] (when using the Windows XP SP2 Firewall).
- 31 -
ROI-S05931
(3) Enter User name and Password, and Select the Connection Entry. After installation of the PNMT, the initial password will be:User name: Password: admin (There is no initial password. Just press Enter. A password can then be set.) Connection: Select Dial-up and Pnmt entry. NOTE If another application is using the SNMP Port, application initialization will not be possible, the application will shut down, and the following message will appear.
- 32 -