Professional Documents
Culture Documents
Usefull IOG Health Checkup Commands
Usefull IOG Health Checkup Commands
Action : Print the Alarm list . ALLIP; Comment : Analyse and clear any IOG related Alarms, following the relevant OPIs .
Action :
Print the SPG node configuration status. IMMCT:SPG=0; IMCSP; NODE CONFIGURATION STATUS SPG 0 NPAIR 1 END; EX NODE CM STATUS STATE A 1 WORKING NORMAL SB NODE CM STATUS STATE B 2 WORKING NORMAL
Comment :
The result printout should be as shown above. If its different then start an Investigation into why .
Action :
Print the SP Link Data to check that the State for both links is WO . EXSLP:SPG=0;
Comment :
Action :
Print the SP Fault Detection Log and the SP Unit Repair List for both Nodes. DISFP:SPG=0; RESUP:SPG=0,NODE=A; RESUP:SPG=0,NODE=B;
Comment :
If there are any boards listed for any of the above print commands , then follow The next action.
Action :
If there are suspect boards detected then perform a repair check. BLSNI:SPG=0,NODE=sb_side; RESUI:SPG=0,NODE=faulty_node; a) If the result is O.K , then deblocked the standby node. BLSNE:SPG=0,NODE=sb_side; b) If the result is Not O.K , then follow the relevant OPI to clear the fault.
Action :
Print the SP system list for both nodes and check that the correct system is Active in both nodes. LASYP:SPG=0,VNODE=A; LASYP:SPG=0,VNODE=B;
Action :
Print the SP Software Characteristics for the active system shown in the previous Printout for Node-A. LASSP:SPG=0,VNODE=A,SYSTEM=active_system,SIZE=ALL;
Action :
Print the Node Restart Data for both nodes. IMMCT:SPG=0; IMRDP:NODE=A; IMRDP:NODE=B; END;
Action :
Print the SPS Event Log for both nodes. IMMCT:SPG=0; IMALP:NODE=A; IMALP:NODE=B; END;
Action :
Print the SP Hardware Data for both nodes. IMLCT:SPG=0; IMHWP:NODE=A; IMHWP:NODE=B; END;
Action :
Print the IO Unit Modes for both nodes. IMMCT:SPG=0; INIOP:NODE=A; INIOP:NODE=B; END;
Action :
Comment :
If the printout contains entries, then investigate and clear using the relevant OPIs.
Action :
Comment :
If the STATUS is ACTIVE/S, then print the SP Trace System Log Status for Both Nodes. IMTLP:NODE=ALL; END;
Action :
IMRLP:PTYPE=INCIDENT; END;
Action:
Print the Transaction Logging conditions and current operating state. IMLCT:SPG=0; MCTLP; END;
Action :
Print the DCS Line Unit Data and status. IMLCT:SPG=0; ILLUP; END;
Action :
Print the DCS Port Data and status. IMLCT:SPG=0; ILNPP; END;
Action :
Print the DCS Route Data and status. IMLCT:SPG=0; ILROP; END;
Action :
Print the Media Attributes for HD-1 in Node A. INMCT:SPG=0; INMEP:NODE=A,IO=HD-1; END;
Action :
Print the SP Volume and File information. INMCT:SPG=0; INVOP; INVOP:VOL=( each volume from the previous printout ) ; INFIP; END;
Action :
Print the STS Data Base configuration data. IMLCT:SPG=0; SDDOP:OBJTYPE=ALL,AREA=OPER; END;
Action :
Action :
Action :
Action :
Action :
Action :
Action :
Action :
Action :
Comment :
Repeat the command a few times to verify that the NIU changes.
Action :
Action :
Verify that Charging Data is being transferred to the active subfile. INMCT:SPG=0; INFIP:FILE=TTFILE00- ( ACTIVESUB ); END;
Comment :
Check for NUSER = 1 in the File Attributes printout. Also repeat the above Command over a period of time to verify that the SIZE is increasing.
Action :
Verify that all the TT Subfiles have been transferred to XMATE. INFSP:FILE=TTFILE00,DEST=XMATE;
Comment :
Action :
Check on XMATE for the Statistics Data Reports on SP LOAD for both nodes.