Professional Documents
Culture Documents
5-Channel BTL Driver For DVD Player AM5888S
5-Channel BTL Driver For DVD Player AM5888S
kr
Applications
BTL driver for CD, CD-ROM and DVD.
Features
1) Two channels are voltage-type BTL drivers for actuators of tracking and focus. Two channels are voltage-type BTL driver for sled and spindle motors. It is also built-in one channel bi-direction DC motor driver for tray. 2) Wide dynamic range [9.0V (typ.) when Vcc1= Vcc2= 12V, at RL= 20 load]. 3) Separating power of Vcc1 and Vcc2 is to improve power efficiency by a low supply voltage for tracking, focus, and spindle. 4) Level shift circuit built-in. 5) Thermal shut down circuit built-in. 6) Mute mode built-in. 7) Dual actuator drivers: A general purpose input OP provides differential input for signal addition. The output structure is two power OPAMPS in bridge configuration. 8) Sled motor driver: A general purpose input OP provides differential input for signal addition. The output structure is one power OPAMP in bridge configuration. 9) Spindle driver: Single input linear BTL driver. The output structure are two power OPAMPS in bridge configuration. 10) Tray in-out driver: The DC motor driver supports forward/reverse control for tray motor. 11) 2 Built-in regulator controllers Adjustable range 1.5V ~ 4V
AMtek SEMICONDUCTORS
-1-
www.DataSheet.co.kr
Power dissipation *1.7 -35 ~ +85 Operate Temp range **-55 ~ +150 Storage Temp range *When mounted on a 70mm70mm1.6mm glass epoxy board. *Reduced by 13.6mW for each increase in Ta of 1 over 25. **Should not exceed Pd or ASO and Tj=150C values
Limits 13.5
Unit V W
Unit V V
Block diagram
MUTE
BIAS
VINTK
TRB_2
NC
VINLD
GND
VCTL
NC
VCC2
VOLD-
VOLD+
VOTK-
VOTK+
28
27
26
25
24
23
GND
22
PGND
21
20
19
Vcc2 15K
18
17
16
15
10K
MUTE
+ 25K +
10K +
Spindle Driver(4X)
Actuator Driver(6x)
Actuator Driver(6x)
TRAY DRIVER
10K
1
VINFC
2
TRB_1
3
REGO2
4
VINSL+
5
REGO1
6
FWD
7
REV
8
VCC1
9
VOTR-
10
VOTR+
11
VOSL+
12
VOSL-
13
VOFC-
14
VOFC+
AMtek SEMICONDUCTORS
-2-
www.DataSheet.co.kr
Electrical characteristics
( Unless otherwise specified Ta=25, Vcc1=12V, Vcc2=5V, BIAS=2.5V, RL=8/10/20/45) Parameter Quiescent current Voltage for mute ON Voltage for mute OFF <Actuator drivers> Output offset voltage Maximum output voltage Voltage gain <Sled motor driver> Output offset voltage Maximum output voltage Closed loop voltage gain <Spindle motor driver> Output offset voltage Maximum output voltage Voltage gain Gain error by polarity <Tray motor driver> Output saturation voltage 1 Output saturation voltage between F&R Output saturation voltage 2 Output adjustable gain on H side voltage <Tray motor driver input logic> High level input voltage Low level input voltage High level input current <Regulator> ** Output voltage Output load differential Power supply voltage differential VIH VIL IIH Vreg VRL VVCC 1.5 -0.3 1.5 -50 -25 180 Vcc 0.5 270 4.0 50 25 V V A VFWD=VREV=5V IL = 500mA *** IL = 0~500mA (Vcc=4.5~8V) IL = 500mA VSAT1 VSAT1 VSAT2 VVtrH 0.7 1.0 7.4 1.1 1.55 9.2 1.5 0.1 2.2 11 V V V dB Upper + Lower saturation, IL=200mA Output saturation voltage 1 between FWD and REV Upper + Lower saturation, IL=500mA VCTL=2V Voofld Vomax Gvld Gvld 13.3 0 3.5 15.5 1 50 17.5 2 mV V dB dB @8 Load VIN=BIAS+0.2Vpp ac @1KHz VIN=BIAS+0.2Vpp ac @1KHz Voofsl Vomsl Gvsl 7.5 18 9.0 20 100 22 mV V dB @20 Load VIN=BIAS+0.2Vpp ac @1KHz Symbol Icc Vston Vstoff Voo Vom Gv Limit Typ 30 4.0 23.5 Unit mA V V mV V dB Conditions P.S
0 0
mV mV
*This device is not designed for protection against radioactive rays. ** It is based on 8550C PNP application *** It is based on 8550D
AMtek SEMICONDUCTORS
-3-
www.DataSheet.co.kr
VINFC
28
MUTE
TRB_1
27
BIAS
REGO 2
26
VINTK
VINSL+
25
TRB_2
REGO 1
24
NC
AM5888S
FWD
23
VINLD
REV
22
GND
Vcc1
21
VCTL
VOTR-
20
NC
VOTR+
10
19
Vcc2
VOSL+
11
18
VOLD-
VOSL-
12
17
VOLD+
VOFC-
13
16
VOTK-
VOFC+
14
15
VOTK+
AMtek SEMICONDUCTORS
-4-
www.DataSheet.co.kr
Pin description
PIN No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
Pin Name VINFC TRB_1 REGO2 VINSL+ REGO1 FWD REV Vcc1 VOTRVOTR+ VOSL+ VOSLVOFCVOFC+ VOTK+ VOTKVOLD+ VOLDVcc2 NC VCTL GND VINLD NC TRB_2 VINTK BIAS MUTE Input for focus driver
Function
Connect to external transistor base Regulator voltage output, connect to external transistor collector Input for the sled driver Regulator voltage output, connect to external transistor collector Tray driver forward input Tray driver reverse input Vcc for pre-drive block and power block of sled and tray Tray driver output (-) Tray driver output (+) Sled driver output (+) Sled driver output (-) Focus driver output (-) Focus driver output (+) Tracking driver output (+) Tracking driver output (-) Spindle driver output (+) Spindle driver output (-) Vcc for power block of spindle, tracking and focus No Connection Speed control input of tray driver Ground Input for spindle driver No Connection Connect to external transistor base Input for tracking driver Input for reference voltage Input for mute control
Notes) Symbol of + and (output of drivers) means polarity to input pin. (For example, if voltage of pin1 is high, pin14 is high.)
AMtek SEMICONDUCTORS
-5-
www.DataSheet.co.kr
2.0
1.5
1.0
25
50
75
100
125
150
Ta()
*70mm70mm1.6mm glass epoxy board. *De-rating is done at 13.6mW/ for operating above Ta=25
Operation notes
1) The built-in thermal shutdown circuit mutes the output current when the chip temperature reaches 175 (typ.). The hysteresis is set to 25 (typ.), so the circuit will start up again when the chip temperature falling to 150 (typ.). 2) In case mute pin voltage is under 0.5V or NC, output current is muted (except for tray motor driver). Mute pin voltage should be more than 2.0V for normal application. 3) Bias pin (pin 27) should be pulled up to more than 1.2V. In case the bias pin voltage is pulled down below 0.9V (typ.), the output current is muted. 4) Insert the bypass capacitor (~ 0.1uF ) between Vcc pin and GND pin as close as possible. 5) Heat dissipation fins are attached to the GND on the inside of the package. Make sure to connect them to the external GND. 6) NC pins ( 20, 24 ) are reserved for internal test. Please keep them floating.
AMtek SEMICONDUCTORS
-6-
www.DataSheet.co.kr
L L OPEN OPEN Open mode L H L H Reverse mode H L H L Forward mode H H L L Brake mode Input circuit of pin6 and pin7 is designed to avoid simultaneous activation of upper and lower output tr. ; however, in order to improve reliability, apply motor forward/reverse input once through open mode. We recommend time period for open longer than 10msec. H side Output voltage on output voltage (VOL+, VOL-) varies depending on output control terminal for tray (pin21). H side output voltage is set three times (9.2dB Typ.) VTCL(pin21). And, L side output voltage is equal to output saturation voltage.
Application circuit
SERVO
U-COM
Tracking
Vcenter
Spindle
MUTE
Focus
FWD
REV
Sled
5v or 12V
5V
Tracking coil
NC
NC
28
27
26
25
24
23
GND
22
PGND
21
20
19
Vcc2 15K
18
17
16
15
10K
MUTE
+ + 25K -
10K +
Spindle Driver(4X)
Actuator Driver(6x)
Actuator Driver(6x)
TRAY DRIVER
10K
1
10K 47uF 5V
3
10K 16.4K
5
10K
7
12V
9
M
10
11
M
12
13
14
Focus coil
AMtek SEMICONDUCTORS
47uF
-7-
www.DataSheet.co.kr
5V
V23
V28
V27
V26
V19
10
NC
OPEN
NC
28
27
26
25
24
23
GND
22
PGND
21
20
19
Vcc2 15K
18
17
16
15
10K
MUTE
+ + -
10K +
25K
Spindle Driver(4X)
Actuator Driver(6x)
Actuator Driver(6x)
TRAY DRIVER
10K
1
V1 ADJ 2.5V REGOUT
2
10K
3
10K
4
V4
10
11
12
13
14
V6
V7
V8
45
20
10
16.4K
47uF
5V
AMtek SEMICONDUCTORS
47uF
10K
-8-
www.DataSheet.co.kr
E1
1 B b1 e
14
A2
0.089
A1
SYMBOL A A1 A2 B b1 C D E E1 e L
MILLIMETERS Min. Max. 2.75 0.3 2.45 4.95 5.35 0.23 0.47 0.2 0.36 17.89 18.8 7.3 7.9 9.6 10.65 0.8 (TYP) 0.3 -
INCHES Min. Max. 0.108 0.012 0.096 0.195 0.211 0.009 0.019 0.008 0.014 0.704 0.740 0.287 0.311 0.378 0.419 0.031(TYP) 0.012 -
AMtek SEMICONDUCTORS
-9-
www.DataSheet.co.kr
AMtek
AMtek SEMICONDUCTORS
- 10 -