Professional Documents
Culture Documents
GENERAL INFORMATION
Passive Restraint System Inspection - Asian
INTRODUCTION
When a vehicle equipped with passive restraint system has
been involved in a collision, certain systems and components must be
inspected and or replaced regardless of whether or not the air bag has
deployed. Follow the manufacturers guidelines provided in this
article.
ACURA (1988-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - ACURA (1988-98)
Model
Year
(1) Location
Integra ..............
Legend ...............
1994-98 .....................
1991-95 .....................
1988-90 ......................
NSX .................. 1993-98 .....................
1991-92 ......................
Vigor ................ 1993-94 .....................
1992 ........................
2.2CL ................. 1997 .......................
2.3CL ................. 1998 .......................
2.5TL ................ 1995-98 .....................
3.0CL ................ 1997-98 .....................
3.2TL ................ 1996-98 .....................
3.5RL ................ 1996-98 .....................
SLX .................. 1996-98 .....................
D/P
D/P
DS
D/P
DS
D/P
DS
D/P
D/P
D/P
D/P
D/P
D/P
D/P
INSPECTION PROCEDURES
Action
Component or System
* Air Bag Module(s)
Replace After
* Seat Belt Tensioners (If Equipped)
Deployment
* SRS Control Unit
* Cable Reel
Inspect & If
Damaged, Replace * Dash or Impact Sensors (If Equipped)
Component
* Seat Belts
(Even If Air
Bag Did Not
Deploy)
* Wiring Harness
* If any components are damaged or bent, they
Comments
must be replaced.
*
DO NOT attempt SRS wiring repairs. If SRS
wiring or harness connectors are faulty,
replace faulty wiring harness.
* After vehicle is repaired, ensure AIR BAG
warning light is functioning properly.
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* Sensing & Diagnostic Module (SDM)
* Instrument Panel Braces
Inspect & If
Damaged, Replace * Instrument Panel Steering Column
Reinforcement Plate
Component
* Seat Belts & Mounting Points
(Even If Air
* Knee Bolsters & Mounting Points
Bag Did Not
* Steering Column
Deploy)
* SRS Coil Assembly
* Wiring Harnesses
* If any components are damaged or bent, they
Comments
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace harness.
HONDA (1991-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - HONDA (1991-98)
Model
Accord
Year
(1) Location
...............
1993-98 .....................
1991-92 ......................
Civic ................ 1994-98 .....................
1992-93 ......................
Civic del Sol ........ 1994-97 .....................
1993 ........................
CR-V ................. 1997-98 .....................
Odyssey .............. 1995-98 .....................
Prelude .............. 1994-98 .....................
SI 4WS ............. 1992-93 .....................
Except SI 4WS ...... 1992-93 ......................
Passport ........... 1995 1/2-98 ...................
(1) - Location Definitions: D/P = Drivers & Passengers
Side, DS = Drivers Side Only, SI = Side Impact.
D/P
DS
D/P
DS
D/P
DS
D/P
D/P
D/P
D/P
DS
D/P
INSPECTION PROCEDURES
Action
Component or System
* Air Bag Module(s)
Replace After
* Seat Belt Tensioners (If Equipped)
Deployment
* SRS Control Unit
* Cable Reel
Inspect & If
Damaged, Replace * Dash Sensors (1991-94)
* Seat Belts
Component
* SRS Control Unit
(Even If Air
* Wiring Harness
Bag Did Not
Deploy)
* If any components are damaged or bent, they
Comments
must be replaced.
* DO NOT attempt SRS wiring repairs. If SRS
wiring or harness connectors are faulty,
replace faulty wiring harness.
* After vehicle is repaired, ensure AIR BAG
warning light is functioning properly.
INSPECTION PROCEDURES TABLE - HONDA (1995 1/2-98 PASSPORT)
HYUNDAI (1994-98)
AIR BAG APPLICATION
Model
Accent ...............
Elantra ..............
Sonata ...............
Tiburon ..............
Year
1995-98
1996-98
1994-95
1995-98
1997-98
(1) Location
.....................
.....................
......................
.....................
.....................
D/P
D/P
DS
D/P
D/P
INSPECTION PROCEDURES
INSPECTION PROCEDURES TABLE - HYUNDAI (1994-98)
Action
Component or System
* Air Bag Module(s)
Replace After
* Control Module
Deployment
* Steering Column Clockspring
* Any Seat Belt In Use At Time Of Collision
Inspect & If
Damaged, Replace * Steering Column
* Steering Wheel
Component
* Wiring Harness
(Even If Air
Bag Did Not
Deploy)
* If any components are damaged or bent, they
Comments
must be replaced.
* DO NOT attempt SRS wiring repairs. If SRS
wiring or harness connectors are faulty,
replace faulty wiring harness.
INFINITI (1990-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - INFINITI (1990-98)
Model
G20
I30
J30
M30
Q45
QX4
Year
(1) Location
......... 1993-96
........... 1998
1997
1996
........... 1997
1994-96
1993
......... 1990-92
........... 1998
1997
1994-96
1990-93
......... 1997-98
Inspection Table
INFINITI-2
INFINITI-1
INFINITI-1
INFINITI-2
INFINITI-1
INFINITI-2
INFINITI-3
INFINITI-3
INFINITI-1
INFINITI-1
INFINITI-2
INFINITI-3
INFINITI-1
INSPECTION PROCEDURES
Action
Component or System
* Air Bag Module(s)
Replace After
* Control Unit, Diagnosis
Deployment
* Satellite Sensor (1)
* Seat Belt Pretensioners (2)
* Side Air Bag Module (1)
* Center Pillar Inner (1)
Inspect & If
Damaged, Replace * Instrument Panel
* Seat (1)
Component
* Seat Belt Pretensioners (2)
(Even If Air
* Spiral Cable
Bag Did Not
* Steering Wheel
Deploy)
* Wiring Harnesses
* Inspect all SRS components for dents,
Comments
deformities or rust.
* After repairs are completed, check AIR BAG
warning light to ensure system is functioning
properly.
(1) - On side of impact.
- Except I30 and QX4.
(2)
INSPECTION PROCEDURES TABLE - INFINITI-2
(2)
Action
Component or System
* Air Bag Module(s)
Replace After
* Control Unit, Diagnosis
Deployment
* Sensors In Affected Collision Area
* All Sensors
Inspect & If
Damaged, Replace * Spiral Cable
* Steering Wheel
Component
* Wiring Harnesses
(Even If Air
Bag Did Not
Deploy)
Comments
* Inspect all SRS components for dents,
deformities or rust.
ISUZU (1990-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - ISUZU (1990-98)
Model
Hombre .......
Impulse ......
Oasis ........
Rodeo ........
Stylus .......
Trooper ......
Year
(1) Location
1996-97 ...........
1990-92 ...........
1996-98 ..........
1996-98 ..........
1995 1/2 .........
1991-93 ...........
1996-98 ..........
1995 ............
DS
DS
D/P
D/P
D/P
DS
D/P
D/P
Inspection Table
..................
..................
..................
..................
..................
..................
..................
..................
ISUZU-1
ISUZU-5
ISUZU-2
ISUZU-3
ISUZU-3
ISUZU-5
ISUZU-3
ISUZU-4
INSPECTION PROCEDURES
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* Seat Belt Tensioners (If Equipped)
* SRS Control Unit
* Cable Reel
Inspect & If
Damaged, Replace
Component
(Even If Air
Bag Did Not
Deploy)
* Seat Belts
* Wiring Harness
* If any components are damaged or bent, they
Comments
must be replaced.
* DO NOT attempt SRS wiring repairs. If SRS
wiring or harness connectors are faulty,
replace faulty wiring harness.
* After vehicle is repaired, ensure AIR BAG
warning light is functioning properly.
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* Sensing & Diagnostic Module (SDM)
Inspect
&
If
* Instrument Panel Braces
Damaged, Replace * Instrument Panel Steering Column
Reinforcement Plate
Component
* Seat Belts & Mounting Points
(Even If Air
* Knee Bolsters & Mounting Points
Bag Did Not
* Steering Column
Deploy)
* SRS Coil Assembly
* Wiring Harnesses
* If any components are damaged or bent, they
Comments
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace harness.
INSPECTION PROCEDURES TABLE - ISUZU-4
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* All Sensors
Inspect
&
If
* SRS Coil Assembly
Damaged, Replace * Instrument Panel Steering Column
Reinforcement Panel
Component
* Instrument Panel Braces
(Even If Air
* Knee Bolsters
Bag Did Not
* Seat Belts Mounting Points
Deploy)
* Sensors In Area of Accident Damage
* Steering Column
* If any components are damaged or bent, they
Comments
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace harness.
INSPECTION PROCEDURES TABLE - ISUZU-5
Action
Component or System
Replace After
Deployment
Inspect
&
If
* Arming Sensor
Damaged, Replace * Coil Assembly
* Diagnostic Energy Reserve Module (DERM)
Component
* Forward Sensor
(Even If Air
* Instrument Panel-To-Steering Column
Bag Did Not
Reinforcement
Deploy)
* Knee Pad
* Passenger Compartment Sensor
* Steering Column
* Wiring Harness & Brackets
* If any components are damaged or bent, they
Comments
must be replaced.
KIA (1995-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - KIA (1995-98)
Model
Sephia
Year
Sportage
..............
............
(1) Location
1996-98 ......................
1995 1/2 .....................
1996-98 ......................
D/P
D/P
D/P
INSPECTION PROCEDURES
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* Air Bag Diagnosis Control Unit
Inspect & If
Damaged, Replace * Clockspring
* Impact Sensors Sensor Mountings (1)
Component
* Steering Column
(Even If Air
* Steering Wheel
Bag Did Not
Deploy)
* Wiring Harness
Comments
* After repairs a completed, ensure Warning
Light is functioning properly.
- 1995 1/2 Sephia only.
(1)
LEXUS (1990-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - LEXUS (1990-98)
Model
ES250
ES300
GS300
GS400
LS400
LX450
LX470
SC300
SC400
Year
(1) Location
Inspection Table
LEXUS-6
LEXUS-3
LEXUS-1
LEXUS-4
LEXUS-5
LEXUS-3
LEXUS-4
LEXUS-3
LEXUS-3
LEXUS-1
LEXUS-4
LEXUS-6
LEXUS-1
LEXUS-2
LEXUS-1
LEXUS-4
LEXUS-5
LEXUS-1
LEXUS-4
LEXUS-5
INSPECTION PROCEDURES
Action
Component or System
* Air Bag Module(s)
Replace After
* Air Bag Sensor Assembly
Deployment
* Front Seat Belt Pretensioners (1)
* Glove Compartment Door (2)
Inspect & If
Damaged, Replace * Instrument Panel
* Instrument Panel Reinforcement
Component
* Spiral Cable
(Even If Air
* Steering Wheel
Bag Did Not
Deploy)
* Wiring Harness & Connectors
Comments
* If any components are damaged or bent, they
must be replaced.
(1) - 1995 LS400 only.
- 1997 ES300, 1996 LS400 and 1996-97 LX450 only.
(2)
INSPECTION PROCEDURES TABLE - LEXUS-2
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* Air Bag Sensor Assembly
* Front Air Bag Sensors
* Seat Belt Pretensioner
* Instrument Panel
Inspect & If
Damaged, Replace * Instrument Panel Reinforcement
Component
(Even If Air
Bag Did Not
Deploy)
Action
Component or System
* Air Bag Module(s)
Replace After
* Air Bag Sensor Assembly
Deployment
* Seat Belt Pretensioner (1)
* Side Air Bag Modules
* Side Air Bag Sensor Assembly
* Glove Compartment Door (2)
Inspect & If
Damaged, Replace * Instrument Panel Instrument Panel
Reinforcement
Component
* Seat Belt Pretensioner (1)
(Even If Air
* Spiral Cable
Bag Did Not
* Steering Wheel
Deploy)
* Wiring Harness & Connectors
* If any components are damaged or bent, they
Comments
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace entire wiring harness.
(1) - Except 1997 LS400.
- 1997 LS400 only.
(2)
INSPECTION PROCEDURES TABLE - LEXUS-4
Action
Component or System
* Air Bag Module(s)
Replace After
* Center Air Bag Sensor Assembly
Deployment
* Front Air Bag Sensors
* Front Seat Belt Tensioners (1)
* Glove Compartment Door (2)
Inspect & If
Damaged, Replace * Instrument Panel
* Instrument Panel Reinforcement
Component
* Spiral Cable
(Even If Air
* Steering Wheel
Bag Did Not
Deploy)
* Wiring Harness & Connectors
Comments
* If any components are damaged or bent, they
must be replaced.
*
Wiring for Front Air Bag Sensors can be
repaired following manufacturers
instructions.
(1) - 1993-95 GS300 and 1993-94 LS400.
- Except 1994-95 SC300 and SC400.
(2)
Action
Component or System
* Air Bag Module
Replace After
* Center Air Bag Sensor Assembly
Deployment
* Front Air Bag Sensors
* Spiral Cable
Inspect & If
Damaged, Replace * Steering Wheel
* Wiring Harness & Connectors
Component
(Even If Air
Bag Did Not
Deploy)
* If any components are damaged or bent, they
Comments
must be replaced.
* Wiring for Front Air Bag Sensors can be
repaired following manufacturers
instructions.
INSPECTION PROCEDURES TABLE - LEXUS-6
MAZDA (1990-98)
AIR BAG APPLICATION
Model
Miata
Year
........
Millenia .....
MPV ..........
MX-3
MX-6
.........
.........
(1) Location
1995-97 ...........
1994 .............
1990-93 ...........
1995-98 ...........
1996-98 ...........
1995 .............
1994 .............
1994-95 ...........
1995-98 ...........
1994 .............
1993 .............
D/P
D/P
DS
D/P
D/P
DS
DS
D/P
D/P
D/P
DS
Inspection Table
.................
.................
..................
.................
.................
..................
..................
.................
.................
.................
..................
MAZDA-1
MAZDA-2
MAZDA-2
MAZDA-1
MAZDA-1
MAZDA-1
MAZDA-2
MAZDA-2
MAZDA-1
MAZDA-2
MAZDA-2
Pickup
.......
Protege ......
RX7 ..........
626
..........
929
..........
1996-98 ...........
1995-96 ...........
1995-98 ...........
1994-95 ...........
1990-93 ...........
1995-98 ...........
1994 .............
1993 .............
1992-95 ...........
D/P .................
DS ..................
D/P .................
D/P .................
DS ..................
D/P .................
D/P .................
DS ..................
D/P .................
MAZDA-2
MAZDA-2
MAZDA-1
MAZDA-2
MAZDA-2
MAZDA-1
MAZDA-2
MAZDA-2
MAZDA-2
INSPECTION PROCEDURES
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* Air Bag Sensor Unit
* Clockspring
Inspect & If
Damaged, Replace * Impact Sensors & Sensors Mountings
* Steering Column
Component
* Steering Wheel
(Even If Air
* Wiring Harness
Bag Did Not
Deploy)
Comments
* DO NOT attempt wiring harness repairs.
Replace entire wiring harness.
* Impact sensors must always be installed with
arrow on sensor facing front of vehicle.
INSPECTION PROCEDURES TABLE - MAZDA-2
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* Air Bag Diagnosis Control Unit
* Clockspring
Inspect & If
Damaged, Replace * Impact Sensors & Sensors Mountings
* Steering Column Steering Wheel Wiring Harness
Component
(Even If Air
Bag Did Not
Deploy)
Comments
* DO NOT attempt wiring harness repairs.
Replace entire wiring harness.
* Impact sensors must always be installed with
arrow on sensor facing front of vehicle.
MITSUBISHI (1990-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - MITSUBISHI (1990-98)
Model
Diamante
Year
Eclipse
.....
......
Expo .........
Galant .......
Mirage
Montero
.......
......
(1) Location
Inspection Table
MITSUBISHI-1
MITSUBISHI-2
MITSUBISHI-2
MITSUBISHI-1
MITSUBISHI-3
MITSUBISHI-1
MITSUBISHI-1
MITSUBISHI-2
MITSUBISHI-1
MITSUBISHI-4
MITSUBISHI-4
MITSUBISHI-2
MITSUBISHI-2
D/P ............
DS .............
D/P ............
D/P ............
DS .............
MITSUBISHI-2
MITSUBISHI-3
MITSUBISHI-1
MITSUBISHI-2
MITSUBISHI-2
Montero
Sport ....... 1997-98 ...........
Sigma .......... 1990 ............
3000GT ....... 1997-98 ...........
1994-96 ...........
1991-93 ...........
INSPECTION PROCEDURES
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* SRS Control Unit
* Clockspring
Inspect & If
Damaged, Replace * Steering Column & Intermediate Joint
* Steering Wheel
Component
* Wiring Harness
(Even If Air
Bag Did Not
Deploy)
Comments
* If any components are damaged or bent, they
must be replaced.
INSPECTION PROCEDURES TABLE - MITSUBISHI-2
Action
Component or System
* Air BagModule(s)
Replace After
* Front Impact Sensors
Deployment
* SRS Control Unit
* Clockspring
Inspect & If
Damaged, Replace * Steering Column & Intermediate Joint
* Steering Wheel
Component
* Wiring Harness
(Even If Air
Bag Did Not
Deploy)
* If any components are damaged or bent, they
Comments
must be replaced.
INSPECTION PROCEDURES TABLE - MITSUBISHI-3
Action
Component or System
* Air Bag Module(s)
Replace After
* Clockspring
Deployment
* Front Impact Sensors
* SRS Control Unit
* Steering Column & Intermediate Joint
* Steering Wheel
* Wiring Harness
Inspect & If
Damaged, Replace
Component
(Even If Air
Bag Did Not
Deploy)
* If any components are damaged or bent, they
Comments
must be replaced.
INSPECTION PROCEDURES TABLE - MITSUBISHI-4
NISSAN (1989-98)
AIR BAG APPLICATION
Model
Altima
Year
...........
(1) Location
Inspection Table
NISSAN-3
NISSAN-4
NISSAN-6
NISSAN-6
NISSAN-1
NISSAN-2
NISSAN-3
NISSAN-4
NISSAN-5
NISSAN-6
NISSAN-6
NISSAN-5
Pickup ..........
Pulsar NX .......
Quest ...........
Sentra
..........
200SX
...........
240SX
...........
300ZX
...........
1996-97 ...........
1989-90 ...........
1997-98 ...........
1996 .............
1994-95 ...........
1997-98 ...........
1995-96 ...........
1994 .............
1993 .............
1997-98 ...........
1995-96 ...........
1997-98 ...........
1995-96 ...........
1994-96 ...........
1991-93 ...........
DS
DS
D/P
D/P
DS
D/P
D/P
DS
DS
D/P
D/P
D/P
D/P
D/P
DS
..............
..............
.............
.............
..............
.............
.............
..............
..............
.............
.............
.............
.............
.............
..............
NISSAN-5
NISSAN-6
NISSAN-3
NISSAN-4
NISSAN-5
NISSAN-3
NISSAN-4
NISSAN-5
NISSAN-6
NISSAN-3
NISSAN-4
NISSAN-3
NISSAN-4
NISSAN-4
NISSAN-6
INSPECTION PROCEDURES
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* Control Unit, Diagnosis
* Crash Zone Sensor (1)
Inspect & If
Damaged, Replace * Instrument Panel
* Passenger Deactivation Switch
Component
* Spiral Cable
(Even If Air
* Steering Wheel
Bag Did Not
Deploy)
* Wiring Harnesses
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt SRS wiring harness repairs.
- 4WD only.
(1)
INSPECTION PROCEDURES TABLE - NISSAN-2
Action
Component or System
* Air Bag Module(s)
Replace After
* Control Unit, Diagnosis
Deployment
* Side Air Bag Module (1)
* Satellite Sensor (1)
* Center Pillar Inner (1)
Inspect & If
Damaged, Replace * Instrument Panel
* Seat (1)
Component
* Spiral Cable
(Even If Air
* Steering Wheel
Bag Did Not
Deploy)
* Wiring Harnesses
* If any components are damaged or bent, they
Comments
must be replaced.
* DO NOT attempt SRS wiring harness repairs.
- On side of impact.
(1)
INSPECTION PROCEDURES TABLE - NISSAN-3
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* Control Unit, Diagnosis
Inspect
&
If
* Instrument Panel
Damaged, Replace * Spiral Cable
* Steering Wheel
Component
* Wiring Harnesses
(Even If Air
Bag Did Not
Deploy)
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt SRS wiring harness repairs.
INSPECTION PROCEDURES TABLE - NISSAN-4
(1)
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* Control Unit, Diagnosis
* All Sensors (1)
Inspect & If
Damaged, Replace * Crash Zone Sensor (2)
* Instrument Panel (3)
Component
* Spiral Cable
(Even If Air
* Steering Wheel
Bag Did Not
Deploy)
* Wiring Harnesses
Comments
* If any components are damaged or bent, they
must be replaced. DO NOT attempt SRS
wiring harness repairs.
(1) - Except Pathfinder and Pickup.
(2) - 4WD Pickup only.
- Pathfinder only.
(3)
INSPECTION PROCEDURES TABLE - NISSAN-6
Action
Component or System
* Air Bag Module(s)
Replace After
* Control Unit, Diagnosis
Deployment
* Sensors In Affected Collision Area
* All Sensors Spiral Cable
Inspect & If
Damaged, Replace * Steering Wheel
* Wiring Harnesses
Component
(Even If Air
Bag Did Not
Deploy)
* If any components are damaged or bent, they
Comments
must be replaced.
* DO NOT attempt SRS wiring harness repairs.
SUBARU (1992-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - SUBARU (1992-98)
Model
Year
(1) Location
D/P
D/P
DS
D/P
DS
D/P
DS
INSPECTION PROCEDURES
Action
Component or System
* Air Bag Module(s)
Replace After
* Air Bag Control Module
Deployment
* Front Impact Sensors (1)
* Side Air Bag Sensors (2)
* Air Bag Control Module
Inspect & If
Damaged, Replace * Combination Switch & Clockspring
* Front Impact Sensors
Component
(Even If Air
Bag Did Not
Deploy)
* DO NOT attempt SRS wiring repairs.
Comments
* If any components are damaged or bent, they
must be replaced.
(1) - If Equipped.
- 1998 Legacy, on side of deployment.
(2)
SUZUKI (1995-98)
AIR BAG APPLICATION
AIR BAG APPLICATION TABLE - SUZUKI (1995-98)
Model
Esteem ..............
Sidekick ............
Swift ...............
X90 .................
Year
1995-98
1996-98
1995-98
1996-98
(1) Location
......................
......................
......................
......................
D/P
D/P
D/P
D/P
INSPECTION PROCEDURES
(1)
TOYOTA (1990-98)
Model
Avalon
Year
...........
1998
1996-97
1995
Camry ............ 1998
1997
1996
1994-95
1992-93
Celica ............ 1998
1996-97
1994-95
1990-93
Corolla .......... 1998
1996-97
1994-95
1993
Land Cruiser ..... 1998
1995-97
MR2 ............. 1994-95
1991-93
Paseo .......... 1996-97
1993-95
Previa ......... 1996-97
1994-95
1992-93
RAV4 ........... 1996-98
Sienna ........... 1998
Supra .......... 1997-98
1993-96
1990-92
Tercel ........... 1998
1996-97
1995
1993-94
Tacoma ........... 1998
1996-97
T100 ........... 1994-98
4Runner ........ 1996-98
(1) Location
Inspection Table
INSPECTION PROCEDURES
Action
Component or System
* Air Bag Module(s)
Replace After
* Air Bag Sensor Assembly
Deployment
* Front Air Bag Sensors (1)
* Seat Belt Pretensioner (2)
* Seatback Assembly (2) (3)
* Side Air Bag Modules (If Equipped) (2)
* Side Air Bag Sensor Assembly
(If equipped) (1)
* Instrument Panel
Inspect & If
Damaged, Replace * Instrument Panel Reinforcement
* Seatback Assembly (2)
Component
* Seat Belt Pretensioner (2)
(Even If Air
* Spiral Cable
Bag Did Not
* Steering Wheel
Deploy)
* Wiring Harness & Connectors
* If any components are damaged or bent, they
Comments
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace entire wiring harness.
(2) - On side of impact.
- Avalon only.
(3)
INSPECTION PROCEDURES TABLE - TOYOTA-2
Action
Component or System
* Air Bag Module(s)
Replace After
* Air Bag Sensor Assembly
Deployment
* Front Air Bag Sensors
* Seat Belt Pretensioner (1)
* Instrument Panel
Inspect & If
Damaged, Replace * Instrument Panel Reinforcement
* Seat Belt Pretensioner (1)
Component
* Spiral Cable
(Even If Air
* Steering Wheel
Bag Did Not
Deploy)
* Wiring Harness & Connectors
Comments
* If any components are damaged or bent, they
must be replaced.
* DO NOT attempt wiring harness repairs.
Replace entire wiring harness.
- Land Cruiser and Tercel only.
(1)
INSPECTION PROCEDURES TABLE - TOYOTA-3
Action
Component or System
* Air Bag Module(s)
Replace After
* Air Bag Sensor Assembly
Deployment
* Front Air Bag Sensor (1)
* Instrument Panel (2)
* Instrument Panel Reinforcement (2)
* Spiral Cable (3)
* Steering Wheel (3)
* Spiral Cable (4)
Inspect & If
Damaged, Replace * Steering Wheel (4)
* Wiring Harness & Connectors
Component
(Even If Air
Bag Did Not
Deploy)
Comments
must be replaced.
(3) - Except 1998 Tacoma.
- 1998 Tacoma.
(4)
INSPECTION PROCEDURES TABLE - TOYOTA-4
Action
Component or System
* Air Bag Module(s)
Replace After
* Air Bag Sensor Assembly
Deployment
* Glove Compartment Door
* Instrument Panel
* Instrument Panel Reinforcement
* Spiral Cable
* Steering Wheel
* Wiring Harness & Connectors
Inspect & If
Damaged, Replace
Component
(Even If Air
Bag Did Not
Deploy)
Comments
* If any components are damaged or bent,
they must be replaced.
INSPECTION PROCEDURES TABLE - TOYOTA-5
Action
Component or System
* Air Bag Module(s)
Replace After
* Center Air Bag Sensor Assembly
Deployment
* Front Air Bag Sensors
* Instrument Panel
* Instrument Panel Reinforcement
* Spiral Cable
* Steering Wheel
* Wiring Harness & Connectors
Inspect & If
Damaged, Replace
Component
(Even If Air
Bag Did Not
Deploy)
* If any components are damaged or bent, they
Comments
must be replaced.
* Wiring for Front Air Bag Sensors can be
repaired following manufacturers
instructions.
INSPECTION PROCEDURES TABLE - TOYOTA-6
Action
Component or System
* Air Bag Module(s)
Replace After
Deployment
* Glove Compartment
* Instrument Panel
* Spiral Cable
* Steering Wheel
* Wiring Harness & Connectors
Inspect & If
Damaged, Replace
Component
(Even If Air
Bag Did Not
Deploy)
* If any components are damaged or bent, they
Comments
must be replaced.
* Wiring for Front Air Bag Sensors can be
repaired following manufacturers
instructions.
Action
Component or System
* Air Bag Module(s)
Replace After
* Air Bag Sensor Assembly
Deployment
* Center Console Bracket Support
* Instrument Panel Spiral Cable
* Steering Wheel
* Wiring Harness & Connectors
Inspect & If
Damaged, Replace
Component
(Even If Air
Bag Did Not
Deploy)
Comments
* If any components are damaged or bent, they
must be replaced.
INSPECTION PROCEDURES TABLE - TOYOTA-9
Action
Component or System
* Air Bag Module(s)
Replace After
* Center Air Bag Sensor Assembly
Deployment
* Front Air Bag Sensors
* Spiral Cable
* Steering Wheel
* Wiring Harness & Connectors
Inspect & If
Damaged, Replace
Component
(Even If Air
Bag Did Not
Deploy)
Comments
* If any components are damaged or bent, they
must be replaced.
* Wiring for Front Air Bag Sensors can be
repaired following manufacturers
instructions.
INSPECTION PROCEDURES TABLE - TOYOTA-10
Action
Component or System
* Air Bag Module(s)
Replace After
* Front Air Bag Sensors
Deployment
* Spiral Cable
* Steering Wheel
* Center Air Bag Sensor Assembly
Inspect & If
Damaged, Replace * Wiring Harness & Connectors
Component
(Even If Air
Bag Did Not
Deploy)
* If any components are damaged or bent, they
Comments
must be replaced.
* Wiring for Front Air Bag Sensors can be
repaired following manufacturers
instructions.