Professional Documents
Culture Documents
Fuel - Air Cycle IC Engine
Fuel - Air Cycle IC Engine
Fuel-Air cycle is defined as the theoretical cycle that is based on the actual properties of the cylinder gases. The Fuel-Air cycle takes into account the following: 1. The actual composition of the cylinder gases (air + fuel + water vapor + residual gases). 2. The variation of the specific heat of these gases with temperature. 3. The incomplete mixing (in-homogeneous) of fuel and air at higher temperatures 4. The variations in the number of molecules present in the cylinder as the temperature and pressure change.
The basic advantage of the fuelair cycle analysis is that while the air cycle studies the effect of CR only on other parameters, with fuel-air cycle we can also study the effect of CR, F/A, inlet pressure and temperature, variable specific heat and other factors on engine performance.
VARIABLE SPECIFIC HEAT: Specific Heat is defined as the amount of heat required to raise the temperature of water by 1 degree. Generally, all gases, except monatomic gases, show an increase in specific heat at high temperatures as shown below.
This increase, however, does not follow any particular law. It can be divided into two main regimes :
the energy which goes into moving the atoms does not
contribute to the temperature rise. Hence, more energy will be required to raise the temperature of a unit mass through one degree.
Since the difference between CP and CV is constant, the value of decreases as the temperature increases. With reference to the figure above the effect can be explained a s follows:
During the compression stroke : the end-of-combustion pressure and temperature will be lower that with constant specific heat i.e. 2 instead of 2.
During the combustion stroke : because the temperature rise during this process decreases as CP increases and because the end-of-compression temperature (T@2) is also lower than T@2 the end-of-combustion temperature and pressure will be lower that with constant specific heat i.e. 3 instead of 3.
During the expansion stroke : the natural adiabatic expansion process would have been represented by the line 3-4, but due to the variable specific heat effect it will follow the path 3-4. This is because the specific heat decreases as the temperature decreases during the expansion, however, still lower than the ideal cycle temperature T@4.
Conclusion: Thus we se that the effect of variable specific heat is to lower the pressure and temperature at point 2 and 3 and hence to deliver less work than the corresponding cycle with constant specific heat.
Dissociation is defined as the disintegration of burnt gases at high temperatures. Disintegration increases with temperatures as shown below. The general effect of dissociation can be explained as follows: as the temperature increases considerable amount of heat will be absorbed by the elements that undergoes dissociation. This heat will be liberated when these elements re-combine as the temperature falls.
During the compression stroke : no significant change because the temperature is still below that required for the dissociation to commence.
During the combustion stroke : because of the high temperature rise during this process dissociation increases causing the maximum cylinder temperature and pressure
3-4. This is because the re-association process liberates some of this heat hence
increases the end-of-expansion temperature and pressure though still below that of ideal cycle. Conclusion: Thus we se that the effect of dissociation is to lower the pressure and temperature at the beginning of the expansion stroke. This causes the engine to suffer a loss in power and drop in thermal efficiency and increase in specific fuel consumption.
Remedy: since the burning of nearly stoichiometric mixture will produce the maximum temperature, dissociation will be maximum at mixtures within stoichiometric. As the mixture becomes lean or rich, the thermal energy produced due to combustion will be low and hence dissociation will be suppressed. This is clearly shown in the following figures.
COMPARISON OF P-V DIAGRAM BETWEEN AIR STANDARD AND FUEL AIR CYCLES FOR SI ENGINE.
efficiency with mixture strength. Fuel-air analysis, however, suggests that the
thermal efficiency will deteriorate as the mixture supplied is enriched.
Effect of Air/Fuel Ratio: From the figure we see that as the mixture is made lean (lesser fuel) the thermal efficiency increases. This is because of the lesser thermal energy released which results in the lowering of the cylinder temperature and pressure hence reducing the specific heat and dissociation losses.
By air-standard cycle theory, engine power is maximum at chemically correct mixture. By air-fuel cycle theory, it peaks at 10% richer mixture beyond which engine power falls rapidly due to erratic, incomplete combustion as well as other losses.
For a given compression ratio, the maximum cycle temperature is reached when mixture is slightly rich (about 6% rich) and that for maximum cycle pressure is at about 10% rich. This is because at chemically correct mixture, due to the chemical equilibrium losses, there is still some oxygen present at state point 3, this will cause more fuel to combine with oxygen and burn raising the temperature of the cylinder. Further, this increment in the number of molecules in the cylinder allows for higher peak pressure as the gas law states: P*V = N*R*T. This also helps in increasing the cycle MEP.
A petrol engine of compression ratio 6 uses a fuel of calorific value 44000 kJ/Kg. The air-fuel ratio is 15:1. The temperature and pressure of the charge at the end of suction stroke are 60oC and 1 bar, respectively. Determine the maximum pressure in the cylinder if the index of compression is 1.32 and the specific heat of the products at constant volume is expressed by the relation CV = 0.71 + 20*10-5*T kJ/Kg.K where T is the temperature in oK. Compare this value with that for a constant specific heat CV = 0.71 kJ/Kg.K.
Carburettor: The process of formation of combustible air fuel mixture by mixing the proper amount of fuel with air before admission to engine cylinder is called carburetion and the device which does this job is called carburettor.