Professional Documents
Culture Documents
BizHub C352 User Guide
BizHub C352 User Guide
Table of Contents
Important Information Before First Use BizHub C352 Control Panel General copy operations To make a copy Feeding the original Scanning the original in separate batches (Separate Scan setting) Scanning a multi-page original from the original glass Selecting a color setting Selecting the original and copy type settings (Simplex/Duplex settings) Specifying the density settings Selecting finishing settings To bind copies with staples Punching holes in copies (Punch settings) Specifying Center Binding Stopping / deleting print jobs General scanning operations Sending data in an email message (Scan to email) Entering the addresses directly Selecting group addresses Selecting destinations from the address book General printing operations Setting printing preferences Orientation Original size and output size Zoom (enlargement and reduction) Input tray (Paper source) Paper type Print type (Duplex printing/Booklet printing) Binding position Combination (printing multiple pages on one page) Stapling and hole punching Output method (Job management) Sorting (collating) and classifying (offset) 3 4 6 6 7 11 13 15 16 17 18 19 20 21 23 24 25 25 26 26 27 29 30 30 30 31 31 31 32 32 34 34 36
Figure 1 Icon 1 Name [Power Save] key Description Press to enter Power Save mode. While the machine is in Power Save mode, the indicator on the [Power Save] key lights up in green and the touch panel goes off. To cancel Power Save mode, press the [Power Save] key again. Displays various screens and messages. Specify the various settings by directly touching the panel. If user authentication or account track settings have been applied, press this key after entering the user name and password (for user authentication) or the account name and password (for account track) in order to use this machine. This key is also used to log off. Press to enter Box mode. While the machine is in Box mode, the indicator on the [Box] key lights up in green. Press to enter Fax mode. While the machine is in Fax mode, the indicator on the [Fax] key lights up in green. Press to enter Scan mode. While the machine is in Scan mode, the indicator on the [Scan] key lights up in green. Press to enter Copy mode. (As a default, the machine is in Copy mode.) While the machine is in Copy mode, the indicator on the [Copy] key lights up in green. Press to clear all settings (except programmed settings) entered in the control panel and touch panel. Press to enter Interrupt mode. While the machine is in Interrupt mode, the indicator on the [Interrupt] key lights up in green and the message Now in Interrupt mode. appears on the touch panel. To cancel Interrupt mode, press the [Interrupt] key again. Press to turn on/off machine operations, for example, for copying, printing or scanning. When turned off, the machine enters a state where it conserves energy. Press the [Stop] key during scanning to stop the scan operation. Press to start scanning. When this machine is ready to begin scanning, the indicator on the [Start] key lights up in green. If the indicator on the [Start] key lights up in orange, scanning cannot begin. Press to restart a stopped job.
2 3
4 5 6 7
8 9
10
11 12
13 14 15 16 17 18 19 20 21 22 23 24
Main power indicator Data indicator [Proof Copy] key Keypad [C] (clear) key [Mode Check] key [Utility/Counter] key [Mode Memory] key Contrast dial [Enlarge Display] key [Accessibility] key [Help] key
Lights up in green when the machine is turned on with the auxiliary power button. Flashes in green while a print job is being received. Lights up in green when data is being printed. Press to print a single proof copy to be checked before printing a large number of copies. Use to type in the number of copies to be produced. Use to type in the zoom ratio. Use to type in the various settings. Press to erase a value (such as the number of copies, a zoom ratio, or a size) entered using the keypad. Press to display screens showing the specified settings. Press to display the Utility screen and Meter Count screen. Press to register the desired copy settings as a program or to recall a registered copy program. Use to adjust the contrast of the touch panel. Press to enter Enlarge Display mode. Press to display the screen for specifying user accessibility functions. Press to display the Help Main Menu screen, where descriptions of the various functions and details of operations can be displayed.
To make a copy
1. Press the [Copy] key to display the Basic screen in Copy mode. 2. Position the document to be copied. 3. Specify the desired copy settings.
Figure 2
4. Using the keypad, type in the desired number of copies. If the number of copies was incorrectly entered, press the [C] (clear) key in the keypad, and then specify the correct number of copies. 5. Press the [Start] key. To stop the copy operation being performed, press the [Stop] key. For details, refer to Stopping scanning/printing on page 23.
Figure 3
Figure 4
To load the original into the ADF Do not load originals that are bound together, for example, with paper clips or staples. Do not load more than 100 sheets or so many sheets that the top of the stack is higher than the mark, otherwise an original misfeed or damage to the original or machine may occur. However, an original that exceeds 100 pages can be scanned in separate batches. If the original is not loaded correctly, the original may not be fed in straight or an original misfeed or damage to the original may occur.
Figure 5
2. Load the original face up in the original feed tray. Load the original pages so that the top of the original is toward the back or the right side of the machine.
Figure 6
Figure 7
To place the original on the original glass When placing the original on the original glass, be sure to lift open the ADF or the original cover at least 15. If the original is placed on the original glass without the ADF or the original cover being lifted at least 15, the correct original size will not be detected. Do not place objects weighing more than 2 kg on the original glass. In addition, do not press down extremely hard on a book spread placed on the original glass, otherwise the original glass may be damaged. For thick books or large objects, make the copy without closing the original cover or ADF. When an original is being scanned with the original cover or ADF open, do not look directly at the light that may shine through the original glass. Although the light that shines through the original glass is bright, it is not a laser beam and, therefore, is not as dangerous. 1. Lift open the original cover or the ADF. 2. Position the original face down onto the original glass. Load the original pages so that the top of the original is toward the back or the left side of the machine.
Figure 8
For transparent or translucent originals, place a blank sheet of paper of the same size as the original over the original.
Figure 9
For bound originals spread over two facing pages, such as a book or magazine, position the top of the original toward the back of this machine and align the original with the mark in the backleft corner of the original scales, as shown.
Figure 10
10
Figure 11
Figure 12
To cancel the Separate Scan setting, touch [Separate Scan] again to deselect it.
11
After the original has been scanned, the following message appears.
Figure 13
3. Load the next batch of the original, and then press the [Start] key. Repeat this step until all pages of the original have been scanned. The buttons that appear in the Change Setting screen differ depending on the specified settings. Settings for the following can be changed Simplex/Duplex, Bind, Zoom, Frame Erase, Center Erase, Original Size The amount of memory available can be checked beside Memory in the upper-right corner of the Basic screen. To delete the image data, press the [Stop] key, and then delete the job. 4. After all original pages have been scanned, touch [Finish]. 5. Press the [Start] key.
12
Figure 14
3. Close the original cover or the ADF. 4. In the Basic screen, touch [Simplex/Duplex]. The Simplex/Duplex screen appears. 5. Touch [1 2], and then touch [OK].
Figure 15
6. Press the [Start] key. Scanning begins. 7. Load the next batch of the original, and then press the [Start] key.
13