Professional Documents
Culture Documents
247
-- Note: SI units
2011
Competitors please replace the sample specification values in the table below with those appropriate for your vehicle and submit this to with your design report. This information will be reviewed by the design judges and may be referred to during the design event. --Please do not modify format of this sheet. Common formatting will help keep the judges happy! --The sample values are fictional and should not be used as the baseline for your designs.
Tire Size and Compound Type Wheels (width, construction) Center of Gravity Design Height Suspension design travel Wheel rate (chassis to wheel center) Roll rate (chassis to wheel center) Sprung mass natural frequency Jounce Damping Rebound Damping Motion ratio / type Camber coefficient in bump (deg / m) Camber coefficient in roll (deg / deg) Static Toe Static camber and adjustment method Front Caster and adjustment method Front Kingpin Axis Kingpin offset and trail Static Akermann and adjustment method Anti dive / Anti Squat Roll center position static Roll center position at 1g lateral acc Steer location, Gear ratio, Steer Arm Length Brake System / Hub & Axle Rotors Master Cylinder Calipers Hub Bearings Upright Assembly Axle type, size, and material
Ergonomics Driver Size Adjustments Seat (materials, padding) Driver Visibility (angle of side view, mirrors?) Shift Actuator (type, location) Clutch Actuator (type, location) Instrumentation Frame 200773808.xls.ms_office V1
Fixed seat and steering wheel. Pedals adjust fore and aft 75mm from center position Wet lay-up carbon, padded lumber and knee protection, 80mm foam head support 210 degree side visibility, 60 x 100mm side mirrors rigidly mounted to nose Manually actuated lever/ linkage, right side cockpit mount Foot pedal, cable actuated Dash mounted temp/oil gauge, 5 LED tach/shift light
1/6/2014
Frame Construction Material Joining method and material Targets (Torsional Stiffness or other) Torsional stiffness and validation method Bare frame weight with brackets and paint Crush zone material Crush zone length Crush zone energy capacity
Frt and rear Tubular space frame / AL Monocoque mid section 1020 and 4130 steel round tubing .5" to 1.125" dia / 2024-t3 .031" thk Al sheet Fusion welding ER70-S6 filler / 2 part room temp cure epoxy 6000 N-m / deg 6500 N-m/deg CAE beam model, 5700 N-m/deg physical test 32 kg closed cell PVC, aramid composite casing 150mm FEA -- 8200 Joules, physical test -- 9680 Joules
Powertrain Manufacture / Model Yamagucci ZAZ-6 4 cylinder, Cyl 3 designed to miss-fire every 8th revolution Bore / Stroke / Cylinders / Displacement 58mm bore / 28mm stroke / 3.75 cylinder / 301 cc Compression ratio 11.6:1 Induction (natural or forced, intercooled) Rotary screw supercharger and Garret T03 turbocharger Throttle Body / Mechanism 45mm, butter-ball throttle actuation Fuel Type E-85 ethanol Max Power design RPM 18000 Max Torque design RPM 16500 Min RPM for 80% max torque 14000 Fuel System (manf'r, and type) Student des/built ,fuel injection, sequential Fuel System Sensors (used in fuel mapping)Air Temp, Coolant Temp, Throttle Pos, Crank Pos,. Fuel Pressure 4.5 bar Injector location 85 mm before and pointing toward intake valve Intake Plenum volume and runner length(s) 1046 cc, 120mm runners Exhaust header design 4-2-1 equal length (+/- 20mm), 50mm collector Effective Exhaust runner length 450mm Ignition System Student des/built ,dual coils, lost spark system Ignition Timing 3-D map, RPM and Throttle position, 23 deg BTDC max advance Oiling System (wet/dry sump, mods) belt driven dry sump, 2 scavenge / 1 pressure pump Coolant System and Radiator location Twin side pod mounted radiators with thermostatic controlled electric fans Fuel Tank Location, Type Floor mounted between firewall and engine, aluminum tank w/fuel bladder Muffler Single glass pack muffler, 2.5 liter volume Other significant engine modifications Height of engine reduced by 60mm with removal of oil sump volume Drivetrain Drive Type Differential Type Final Drive Ratio Vehicle Speed @ max power (design) rpm 1st gear 2nd gear 3rd gear 4th gear 5th gear 6th gear Half shaft size and material Joint type
30mm x 10mm wooden cogged belt clutch pack limited slip, 100Nm preload, 1.4 bias ratio 2.52 18 mph 35 mph 54 mph 72 mph 91 mph removed from trans 30mm OD solid 8620 steel case hardened to Rc 60 1.3mm deep,Rc 28 core TRE mini Tripod- left, Honda Scammer ATV- right
Aerodynamics (if applicable) Type / Configuration Front-Main Element fixed, adj. multi-element flaps, Rear 3 Element, undertray Total Downforce and Drag ( scale using incl. Downforce note ) =212 N, Drag =180 N Aero Balance (% Front, at v=115kph) 45 % front Noteable Features (unsprung mounted, active, etc) lizard skin over hand carved oak structure Optional Information Body Work? Special Bit A? Special Bit B?
3 piece carbon latex body, 2.6 kg complete w/ paint GPS with 'Cartman' voice navigation "Dukes of Hazzard" paint scheme
200773808.xls.ms_office V1
1/6/2014