Professional Documents
Culture Documents
AerodynamicShapeDesign FinalReport Fall2010 PDF
AerodynamicShapeDesign FinalReport Fall2010 PDF
A SENIOR DESIGN PROJECT PREPARED IN PARTIAL FULFILLMENT OF THE REQUIREMENT FOR THE DEGREE OF BACHELOR OF SCIENCE IN MECHANICAL ENGINEERING
Professor: Dr. Sabri Tosunoglu October 25, 2010 This report is written in partial fulfillment of the requirements in EML 4806. The contents represent the opinion of the authors and not the Department of Mechanical and Materials Engineering.
Page |2
Ethics Statement
The work submitted in this project is solely prepared by a team consisting of Gianluca Minnella, Jose Ugas and Yuniesky Rodriguez it is original. Excerpts from others work have been clearly identified, their work acknowledged within the text and listed in the list of references. All of the engineering drawings, computer programs, formulations, design work, prototype development and testing reported in this document are also original and prepared by the same team of students.
Page |3
Table of Contents
Ethics Statement .................................................................................................................................... 2 Table of Contents ................................................................................................................................... 3 List of Figures.......................................................................................................................................... 6 List of Tables ......................................................................................................................................... 10 Abstract ................................................................................................................................................ 11 Chapter 1 1.1 1.2 1.3 Introduction .................................................................................................................... 12 Problem Statement ................................................................................................................. 12 Motivation............................................................................................................................... 12 Literature Review .................................................................................................................... 12 The Kutta-Zhukowsky Condition ..................................................................................... 13 Aerodynamic Characteristics of Airfoils .......................................................................... 15 The Finite Wing ............................................................................................................... 17 Flow Fields around Finite Wings ..................................................................................... 17 Downwash an Induced Drag ............................................................................................. 1 The Fundamental Equations of Finite-Wing Theory ......................................................... 3 The Elliptical Lift Distribution ............................................................................................ 6 Winglets ............................................................................................................................ 8 Boeing 757-200 Background and Winglet Benefits ........................................................ 10
1.3.9.1 Technical features: ................................................................................................... 10 1.3.9.2 Range Capability ....................................................................................................... 12 1.3.9.3 Addition of Winglets................................................................................................. 12 1.3.10 1.3.11 **********KUBRINSKI******* ................................................................................. 15 Optimization................................................................................................................ 15
1.3.11.1 Optimization Overview........................................................................................... 16 1.3.11.2 Optimization Algorithm .......................................................................................... 17 1.3.11.3 Particle-Swarm ....................................................................................................... 18 1.3.11.4 Pareto Front Overview ........................................................................................... 19 1.3.12 OpenFOAM Software .................................................................................................. 21
1.3.12.1 Case Setup: Mesher................................................................................................ 24 1.3.12.2 Case Setup: Solver .................................................................................................. 27 1.3.12.3 Case Setup: Parallel Computing ............................................................................. 28 1.3.13 Experimental Aerodynamics and Wind Tunnel Testing .............................................. 32
Page |4 1.3.13.1 Test Parameters ..................................................................................................... 33 1.3.13.2 Types of Wind Tunnels ........................................................................................... 36 1.3.13.3 Measurement of Airflow Pressure ......................................................................... 39 1.3.13.4 Static pressure ........................................................................................................ 40 1.3.13.5 Total pressure......................................................................................................... 41 1.3.13.6 Proximity to walls or model surfaces ..................................................................... 41 1.3.13.7 Pressure rakes ........................................................................................................ 41 1.3.13.8 Pressure Measurement Devices............................................................................. 41 1.3.13.9 Flow Visualization ................................................................................................... 42 1.3.13.10 Tufts...................................................................................................................... 42 1.3.13.11 Smoke Flow .......................................................................................................... 43 1.3.13.12 Airfoil Testing ....................................................................................................... 44 1.3.13.13 General Testing Considerations ........................................................................... 44 1.3.13.14 Finite Span Wings ................................................................................................. 44 1.3.13.15 Force Measurements Using a Balance System..................................................... 45 1.3.13.16 Profile Drag by Momentum Loss Measurement .................................................. 45 Chapter 2 2.1 2.2 2.3 2.4 Project Formulation and Management........................................................................... 47 Overview ................................................................................................................................. 47 Project Objectives ................................................................................................................... 47 Design Specifications............................................................................................................... 48 Constraints and Other Specifications...................................................................................... 49 Design Parameters .......................................................................................................... 50
Overview of Conceptual Designs Developed .......................................................................... 50 Design Parameter 1 ................................................................................................................. 50 Design Parameter 2 ................................................................................................................. 51 3.3.1.1.1 Analysis of a Simple Swept-Back Wing ..................................................................... 52 3.3.1.1.2 Analysis of a Wing with Winglets that are Vertically Downwards ............................ 55 3.3.1.1.3 Analysis of a Wing with Winglets that are vertically Upwards ................................. 58
3.4
Design Alternate 3................................................................................................................... 60 3.4.1.1.1 Analysis of a Simple Rectangular Wing ..................................................................... 61 3.4.1.1.2 Analysis of Winglets with Camber Pointing Inwards ................................................ 64 3.4.1.1.3 Analysis of a Winglet with Camber Pointing Outwards ............................................ 67
3.5
Chapter 4
Page |5 4.1 4.2 4.3 4.4 4.5 4.6 4.7 Design Variables ...................................................................................................................... 69 Objectives................................................................................................................................ 69 Optimization Algorithm .......................................................................................................... 69 Parameters and Ranges for Optimization ............................................................................... 70 Optimization of 100 Winglets Configurations......................................................................... 74 Discontinuous Pareto Front Graphs ........................................................................................ 76 Optimal Winglet Configurations ............................................................................................. 88 4.7.1.1.1 Simple NACA 2412 .................................................................................................... 89 4.7.1.1.2 Optimal Winglet Configuration #1 ............................................................................ 91 4.7.1.1.3 5.5.2 Optimal Winglet Configuration # 2 .................................................................. 95 Chapter 5 5.1 5.2 5.3 Aerodynamic Analysis ................................................................................................... 100
6.1 Boeing 757 Simple Wing ................................................................................................. 100 Original Boeing 757 Winglets ................................................................................................ 103 6.3 Optimal Boeing 757 Winglets ......................................................................................... 108 Testing and Evaluation .................................................................................................. 112
Chapter 7 7.1
Environmental Impact of Winglets ....................................................................................... 119 Conclusion ..................................................................................................................... 121 Appendix ....................................................................................................................... 122
Appendix A: Boeing 757-200 technical data ......................................................................... 122 Appendix B: Engineering Drawings of Parts .......................................................................... 125 Appendix C: Sample of the three winglets elliptical curves .................................................. 131 References................................................................................................................. 137
Chapter 10
Page |6
List of Figures
Figure 1: Kutta-Zhukowski Condition, No Viscosity.............................................................................. 13 Figure 2: Kutta-Zhukowsi Condition, Viscosity ..................................................................................... 13 Figure 3: Starting Vortices .................................................................................................................... 14 Figure 4: Airfoil Pressure Distribution .................................................................................................. 15 Figure 5: Airfoil characteristics ............................................................................................................. 15 Figure 6: Flow around an airfoil............................................................................................................ 16 Figure 7: Vortex Configuration ............................................................................................................. 17 Figure 8: Superposition of elliptical vortices in steady flow................................................................. 18 Figure 9: Formation of trailing vortices at wing tips ............................................................................ 18 Figure 10: Wing tips flow vortices ........................................................................................................ 19 Figure 11: Formation of trailing vortices at wing tips ............................................................................ 1 Figure 12: Downwash velocity w induced by trailing vortices. .............................................................. 1 Figure 13: Downwash contribution from trailing vortex filament ......................................................... 3 Figure 14: Finite wing Theory parameters ............................................................................................. 4 Figure 15: Finite wing Theory representation ........................................................................................ 4 Figure 16 - Winglet parameters.............................................................................................................. 9 Figure 17: Retrofitting mechanism of blended winglets, created by the Aviation Partners Boeing Company ..................................................................................................................................................... 13 Figure 18: Retrofitting mechanism of blended winglets, created by the Aviation Partners Boeing Company for the 737-200 ........................................................................................................................... 13 Figure 19: Visualization of Dominance ................................................................................................. 20 Figure 20: Pareto Fronts for 2 Objectives............................................................................................. 21 Figure 21: OpenFOAM logo .................................................................................................................. 22 Figure 22: Sample Dict file for OpenFOAM .......................................................................................... 23 Figure 23: OpenFOAM Case Directory Chart ........................................................................................ 24 Figure 24: blockMesh ........................................................................................................................... 25 Figure 25: Mesh and Refinement Box for snappyHexMesh ................................................................. 26 Figure 26: Final Stage of snappyHexMesh............................................................................................ 26 Figure 27: MAIDROC Station ................................................................................................................ 29 Figure 28: Tesla-128 Parallel Computing Lab ....................................................................................... 29 Figure 29: Tesla-128 Cluster Diagram................................................................................................... 30 Figure 30: Subdomains Visualization.................................................................................................... 31 Figure 31: Shell Script ........................................................................................................................... 31 Figure 32: vs. air pressure and temperature ................................................................................. 36 Figure 33 - Open Section Wind Tunnel................................................................................................. 37 Figure 34 - Closed Circuit Wind Tunnel ................................................................................................ 37 Figure 35 - Smoke Wind Tunnel ........................................................................................................... 38 Figure 36 - Pitot Static Probe ................................................................................................................ 40 Figure 37: Tufts Visualization ............................................................................................................... 43 Figure 38: Smoke Flow ......................................................................................................................... 43 Figure 39: Force Balance support ......................................................................................................... 45 Figure 40: Drag by Momentum Loss .................................................................................................... 46 Figure 41: Elliptic winglet Design parameters. ..................................................................................... 48 Figure 42: Blended, Elliptical and Wing-Tip Fence Winglets ................................................................ 50 Figure 43: Isometric View of Domain of Simple Sweptback Wing ....................................................... 53 Figure 44: Residuals vs. Time for Plain Swept-Back Wing .................................................................... 54 Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
Page |7 Figure 45: Isometric View of Trefftz Plane Behind the Wing ............................................................... 54 Figure 46: Streamlines for Plain Swept-Back Wing .............................................................................. 55 Figure 47: Isometric View of Trefftz Plane with Winglets Down.......................................................... 56 Figure 48: Residuals vs. Time for Winglets Down ................................................................................ 57 Figure 49: Streamlines at Wing-Tip with Winglets Down..................................................................... 57 Figure 50: Isometric View of Trefftz Plane for Winglets Up ................................................................. 58 Figure 51: Residuals vs. Time for Winglets Up ..................................................................................... 59 Figure 52: Streamlines for Winglets Up................................................................................................ 60 Figure 53: Plain Wing NACA 2412 Trefftz Plane ................................................................................... 63 Figure 54: Residuals vs. Time for Plain Rectangular Wing.................................................................... 64 Figure 55: Top View of a Cambered In Winglet.................................................................................... 65 Figure 56: Front View of Trefftz Plane for Camber In .......................................................................... 65 Figure 57: Residuals vs. Time for Winglet Camber In ........................................................................... 66 Figure 58: Top View of a Winglet with Camber Out............................................................................. 67 Figure 59: Trefftz Plane of Winglets with Camber Out ........................................................................ 68 Figure 60: Residuals vs. Time for Winglet Camber Out ........................................................................ 68 Figure 61: Graphical representation of optimization limits ................................................................. 71 Figure 62: Graphic definition of optimization parameters .................................................................. 71 Figure 63: Front View (b vs a) of Elliptic Profile ................................................................................... 72 Figure 64: Side View (b vs c) of Elliptic Profile...................................................................................... 73 Figure 65: Discontinuous Pareto Front for Objective 1, minimum Cd and maximum Cl ..................... 76 Figure 66: Discontinuous Pareto Front for Objective 2, minimum Cd minimum Cm........................... 77 Figure 67: Discontinuous Pareto Front for Objective 3, maximum Cl/Cd minimum Cd ...................... 77 Figure 68: Discontinuous Pareto Front for Objective 4, Maximum Cl minimum Cm ........................... 78 Figure 69: Discontinuous Pareto Front for Objective 5. Maximum Cl/Cd maximum Cl ....................... 78 Figure 70: Discontinuous Pareto Front for Objective 6, maximum Cl/Cd minimum Cm ..................... 79 Figure 71: Cl, Cd, Cm............................................................................................................................. 79 Figure 72: Cl vs. Cd ............................................................................................................................... 80 Figure 73: Cm vs Cd .............................................................................................................................. 81 Figure 74: Cm vs Cl ............................................................................................................................... 81 Figure 75: Cl, Cm, Cl/Cd ........................................................................................................................ 82 Figure 76: Cm vs. Cl .............................................................................................................................. 82 Figure 77: Cl/Cd vs .Cm ......................................................................................................................... 83 Figure 78: Cl/Cd vs. Cl ........................................................................................................................... 83 Figure 79: Isometric View of Cl/Cd, Cl, Cd ............................................................................................ 84 Figure 80: Cl vs. Cl/Cd ........................................................................................................................... 84 Figure 81: Cd vs. Cl ............................................................................................................................... 85 Figure 82: Cd vs. Cl/Cd .......................................................................................................................... 85 Figure 83: Isometric View of Cl/Cd, Cd, Cm.......................................................................................... 86 Figure 84: Cd vs. Cm ............................................................................................................................. 86 Figure 85: Cl/Cd vs. Cm ......................................................................................................................... 87 Figure 86: Cl/Cd vs. Cd .......................................................................................................................... 87 Figure 87: Domain of Simple NACA 2412 with a Symmetry Plane ....................................................... 89 Figure 88: Front View of Trefftz Plane for Simple NACA 2412 Wing .................................................... 90 Figure 89: Streamlines at Wing-Tip for Simple NACA 2412 Wing ........................................................ 90 Figure 90: Pressure Field of Simple NACA 2412 Wing .......................................................................... 91 Figure 91: Plot of Residuals vs. Time for Simple NACA 2412 Wing ...................................................... 91 Figure 92: Front View of Optimal Winglet #1 ....................................................................................... 92 Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
Page |8 Figure 93: Side View of Optimal Winglet #1......................................................................................... 92 Figure 94: Top View of Optimal Winglet #1 ......................................................................................... 93 Figure 95: Front View of Trefftz Plane for Optimal Winglet #1 ............................................................ 93 Figure 96: Side View of Pressure Field of Optimal Winglet #1 ............................................................. 94 Figure 97: Streamlines at Wing-Tip for Optimal Winglet #1 ................................................................ 94 Figure 98: Plot of Residuals vs Time for Optimal Winglet #1 ............................................................... 95 Figure 99: Top View of Optimal Winglet #2 ......................................................................................... 96 Figure 100: Front View of Optimal Winglet # 2 .................................................................................... 96 Figure 101: Side View of Optimal Winglet #2....................................................................................... 97 Figure 102: Front View of Trefftz Plane for Optimal Winglet #2 .......................................................... 97 Figure 103: Pressure Field for Optimal Winglet #2 .............................................................................. 98 Figure 104: Streamlines Around Wing-Tip For Optimal Winglet #2 ..................................................... 98 Figure 105: Plot of Residuals vs. T ........................................................................................................ 99 Figure 106: Top View of Domain of Simple, Half 757 Wing with a Symmetry Plane ......................... 101 Figure 107: Front View of Trefftz Plane for Simple 757 Wing ............................................................ 101 Figure 108: Pressure Field around 757 Simple Wing.......................................................................... 102 Figure 109: Streamlines at Wing-Tip of 757 Simple Wing .................................................................. 102 Figure 110: Plot of Residuals vs. Time for Simple 757 Wing .............................................................. 103 Figure 111: Side View of Original Boeing 757 Winglet ....................................................................... 104 Figure 112: Front View of Original Boeing 757 Winglet ..................................................................... 104 Figure 113: Top View of Original Boeing 757 Winglet........................................................................ 105 Figure 114: Front View of Trefftz Plane of Original Boeing 757 Winglet ........................................... 105 Figure 115: Side View of Pressure Field for Original Boeing 757 Winglets ........................................ 106 Figure 116: Streamlines at Wing-Tip for Original Boeing 757 Winglets ............................................. 106 Figure 117: Plot of Residuals vs. Time for Original Boeing 757 Winglets ........................................... 107 Figure 118: Front View of Optimal Boeing 757 Winglets ................................................................... 108 Figure 119: Top View of Optimal Boeing 757 Winglets...................................................................... 109 Figure 120: Side View of Optimal Boeing 757 Winglets ..................................................................... 109 Figure 121: Front View of Trefftz Plane for Optimal Boeing 757 Winglets ........................................ 110 Figure 122: Side View of Pressure Field for Optimal Boeing 757 Winglets ........................................ 110 Figure 123: Streamlines at Wing-Tip of Optimal Boeing 757 Winglet ............................................... 111 Figure 124: Plot of Residuals vs. Time for Optimal 757 Winglets ...................................................... 111 Figure 125: Clearance for Wind Tunnel .............................................................................................. 113 Figure 126: Smoke Tunnel Test Section at Embry-Riddle................................................................... 113 Figure 127: Test Section of Embry-Riddle Wind Tunnel ..................................................................... 114 Figure 128: 1/8 Steel Pin for Retrofitting Winglets .......................................................................... 114 Figure 129: Removing Parts from 3D Printer ..................................................................................... 116 Figure 130: De-powdering Excess of the Parts ................................................................................... 116 Figure 131: Parts Heating in Oven ...................................................................................................... 116 Figure 132: Applying Epoxy to the Wing and Winglets ...................................................................... 117 Figure 133: Parts After Curing Process ............................................................................................... 117 Figure 134: Sanding Parts ................................................................................................................... 118 Figure 135: Drilling Holes in the Wing and Winglets .......................................................................... 118 Figure 136: The structure of the atmosphere below 50 km [6] ......................................................... 120 Figure 137: Boeing 757 aircraft SolidWorks model. These are our target aircraft wings .................. 125 Figure 138: General parts of a commercial airplane. ......................................................................... 126 Figure 139: Comparison of dimension between a 757-200 and a 757-300 aircrafts. ......................... 127 Figure 140: Technical drawings of the wing for a 757 Boeing aircraft. .............................................. 128 Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
Page |9 Figure 141: Technical drawings for a rectangular camber wing NACA 2412 with the same average chord length as the wings of the 757 Boeing aircraft................................................................................ 129 Figure 142: Technical drawing of a random elliptic blended winglet configuration. The optimization parameters a, b, n, cw and are shown also in this figure. ....................................................................... 130
P a g e | 10
List of Tables
Table 1.1: Technical specifications of Boeing 757-200 aircraft serie ................................................... 11 Table 1.2: .............................................................................................................................................. 33 Table 2.1: Project cost analysis............................................................................................................. 49 Table 3.1: Winglet Comparison ............................................................................................................ 51 Table 3.2: Parameters for Winglets Up/Down ..................................................................................... 52 Table 3.3: Domain for Winglets Up/Down ........................................................................................... 53 Table 3.4: Forces for Simple Swept-Back Wing .................................................................................... 55 Table 3.5: Forces for Winglets Down ................................................................................................... 56 Table 3.6: Forces for Winglets Up ........................................................................................................ 59 Table 3.7: Parameters for Winglets Camber In/Out............................................................................. 61 Table 3.8: Domain Box for Winglets Camber In/Out ............................................................................ 62 Table 3.9: Forces of Simple Rectangular Wing ..................................................................................... 63 Table 3.10: Forces for Winglet Camber In ............................................................................................ 66 Table 3.11: Forces for Winglet Camber Out ......................................................................................... 68 Table 4.1: Variables that define elliptical winglets............................................................................... 70 Table 4.2: Range of Optimization Parameters ..................................................................................... 73 Table 4.3: Aerodynamic coefficientes for the NACA2412 without winlgets ........................................ 74 Table 4.4: Corresponding winglets configurations for maximum Cl and Cl/Cd and minimum Cd and Cm ............................................................................................................................................................... 74 Table 4.5: Parameters for Optimal Winglets CFD Analysis................................................................... 88 Table 4.6: Values of Forces for Simple NACA 2412 Wing ..................................................................... 89 Table 4.7: Values of Forces for Optimal Winglet #1 ............................................................................. 91 Table 4.8: Values of Forces for Optimal Winglet #2 ............................................................................. 95 Table 9: Parameters for Boeing 757 CFD Analysis.............................................................................. 100 Table 10: Values of Forces for 757 Simple Wing ................................................................................ 100 Table 11: Values of Forces for Original Boeing 757 Winglets ............................................................ 103 Table 12: Values of Forces for Optimal Boeing 757 Winglets ............................................................ 108 Table 5.13: Comparison of aerodynamic efficiency of 757 with and without winglets ..................... 112 Table 9.1: Types of Boeing 757-200 aircraft [] ................................................................................... 122 Table 9.2: Engines types used by Boeing 757-200 aircrafts [11] ........................................................ 122 Table 9.3: Workload of the Boeing 757-200 aircraft [11] .................................................................. 123 Table 9.4: External dimensions of Boeing 757-200 aircraft [11] ........................................................ 123 Table 9.6: Operational external weights of the Boeing 757-200 aircraft [11] ................................... 123 Table 9.7: Flight performance parameters of the Boeing 757-200 [11] ............................................ 124 Table 9.8: Raw data for the 100 winglet configurations .................................................................... 131 Table 9.9: Data for winglet 1 LMT ...................................................................................................... 133
P a g e | 11
Abstract
The problem being addressed is the design, optimization, construction and testing of a wing tipwinglet configuration. The main objective of this report is to formulate the inverse design procedure so that the mathematical principles are well-posed both theoretically and numerically, and to design and optimize a winglet that best matches the obtained results. The inverse method originates from the attainment of a target pressure distribution for a functional winglet, whereas the optimization method will be accomplished by implementing non-gradient-based methodology algorithms, in an attempt to maximize lift while maintaining (or decreasing) the resultant drag unvaried. The significance of the obtained result parameters will be considered by manufacturing and testing the optimized winglet configuration in Embry-Riddless subsonic wind-tunnel under different angles of attack, while comparing test results obtained by similar methods for currently manufactured and commercialized winglet configurations. The intent being, designing and optimizing a wing- tip winglet configuration capable of reducing induced drag by 2% with respect to currently implemented wing-tip designs.
P a g e | 12
Chapter 1 1.1
Introduction
Problem Statement
The approach and landing phases of a commercial B757-200 passenger aircraft will be
considered. The intent being, design and test a wing tip-winglet configuration capable of increasing the lift-to-drag ratio by 2% with respect to currently implemented applications. The aircraft will be travelling at Mach 0.3 with 8 angle of attack with respect to the free stream, at an altitude of 6000ft; parameters which reflect actual flight conditions. Aircraft specifications are given below.
1.2
Motivation
Within the past 15 years, great attention has been devoted to the study drag-inducing flow
structures in an attempt to strive for better aerodynamic efficiency of an aircraft, while attempting to optimize the volatile consumption of fuel and to increase system life. It was soon understood that these objectives are strictly correlated to one another and, that in order to achieve one, all must be accomplished. Recent avionics have shown that wing-tip disturbances are particularly effective in developing adverse conditions during takeoff and landing procedures, during which lift to drag ratio of a flying aircraft is maximized in order to slow down. Vortices are generated at wings extremities, which impact the overall flight safety by inducing high-speed longitudinal currents and considerable rolling effects on neighboring aircraft; conditions especially unfavorable during low altitude scenarios like take-off and landing. A number of critical failures involving medium to small aircrafts have been recorded within recent years during which, the most plausible cause for malfunction points toward the effects of trailing vortices. It is to compensate for this lack of aerodynamic efficiency that a number of wing-tip devices have steadily appeared in both the private and commercial sector. While understanding complex aerodynamics has always been a needed priority, our intent lies in producing a design project capable of delivering a well thought-out winglet configuration.
1.3
Literature Review
Although it is more efficient and accurate to have finite-wing computations carried out by
computers using readily available computational engineering languages such as FORTRAN, it is incredibly important to have a firm understanding of the theories involved in aerodynamic shape design. It is for this purpose that our emphasis begins with the foundations of aerodynamics. Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 13
Experiments have shown that when a body with a sharp trailing edge is set in motion , the action of the fluid viscosity causes the flow over the upper and lower surfaces to merge smoothly at the trailing edge; this circumstance, which fixes the magnitude of the circulation around the body, is termed the KuttaZhukowski Condition which may be summarized as follows: A body with a sharp trailing edge in motion through a fluid creates about itself a circulation of sufficient strength to hold the rear stagnation point at the trailing edge of finite angle to make the flow along the trailing edge bisector angle smooth. For a body with a cusped trailing edge where the upper and lower surfaces meet tangentially, a smooth flow at the trailing edge requires equal velocities on both sides on the edge in the tangential direction. The Flow around an airfoil at an angle of attack in an inviscid flow develops no circulation and the rear stagnation point occurs on the upper surface as can be seen by Fig.1. Fig.2 is a sketch of the streamlines around an airfoil in viscous flow , indicating the smooth flow past the trailing edge, termed the Kytta-Zhukowsi Condition. This Condition has served as the basis for the calculation of forces around an airfoil.
P a g e | 14 Based on The Helmholtz laws however, the circulation around an airfoil and its wake, being zero before the motion began, must remain zero. The establishment of the Kutta Condition, therefore, requires the formation of the so-called starting vortices (see Fig.3) with a combined circulation equal and opposite to that around the airfoil. The induced flow caused by the vorticity of the airfoil, added to that caused by the starting vortices in the wake, will be just enough to accomplish the smooth flow at the trailing edge.
The starting vortices are left behind as the airfoil moves farther and farther from its starting point, but during the early stages of the motion, Figure 3 indicates that their induced velocities assist those induced by the surface vortices, to satisfy the Condition. It follows that the surface vortex and as a result, the forces acting on the airfoil, will not be as strong in the early stages, when they are being influenced by the starting vortices, as they are after the flow is fully established when the surface vortices must be strong enough by itself to move the rear stagnation point to the trailing edge. Simultaneously, notice the increase in airspeed around the leading edge, as indicated in Figure 3. The resulting pressure decrease manifests a leading edge suction phenomena by which to opposing pressure vectors are located adjacent to each other. A typical pressure distribution of an airfoil is shown in Figure 4, the arrows representing pressure vectors. In a perfect fluid, the total force on the airfoil is the lift , acting normal to . Its
magnitude can be represented as the resultant of two components, one normal to the chord line of magnitude and , given by the integral over the chord of the pressure difference between points
on the upper and lowers surfaces, and the other parallel to the chord line of magnitude , representing the leading edge suction. In a real fluid, viscous effects alter the pressure
P a g e | 15 distribution and friction drag is generated, though at low angles of attack the theoretical pressure distribution can be taken as a valid approximation.
P a g e | 16
The various families of airfoils are designed to show the effects of varying the geometrical variables on their aerodynamic characteristics such as lift, drag and moment, as functions of the geometric angle of attack. The geometric angle of attack is defined as the angle between the flight of the
path and the chord line of the airfoil. The geometrical variables include the maximum chamber mean chamber line and its distance distance behind the leading edge, the maximum thickness
and its
the trailing edge angle between the upper and lower surfaces at the trailing edge. Theoretical studies and wind tunnel experiments show the effects of these variables in a way to facilitate the choice of shapes for specific applications. The lifting characteristics of an airfoil below stall conditions are negligibly influenced by viscosity and the resultant of the pressure forces on the airfoil is only slightly altered by the thickness envelope provided that the ratio of maximum thickness to chord and the maximum mean chamber
remain small, and the airfoil is operating at a small angle of attack. These conditions are usually met during standard operations of airfoils. In a real fluid, lift is within 10% of theory for inviscid fluids up to an angle of attack of of 12 to 15 depending on the geometric factors of Figure 5. Figure 6
shows that at these low angles the streamlines follow the surface smoothly, although particularly on the upper surface the boundary layer causes some deviation. At angles of attack greater than , called
the stalling angle, the flow separates on the upper surface and the Kutta-Zhukowski Condition no longer holds and large vortices are formed. At these angles, the flow becomes unsteady and there is a dramatic decrease in lift, accompanied by an increase in drag and large changes in the moment exerted on the airfoil by the altered pressure distribution
P a g e | 17
known as the Kutta-Zhukowski Condition. It follows that a stationary line vortex normal to a moving stream is the equivalent of an infinite span wing, an airfoil, from resultant force calculations. The airfoilvortex analogy forms the basis for calculating the properties of the finite wing however, since the lift and therefore the circulation, is zero at the tips of a wing of finite span and varies throughout the wing span, additional flow components must be considered. This section is devoted to this addressing these concepts.
circulation (see Figure 7). According to the Kutta-Zhukowski Condition a force having magnitude will be exerted onto the vortex in a direction perpendicular to . Helmotz Laws however, require that
the bound vortex cannot end at the wingtips as it must form a complete circuit, or it must extend to infinity or a boundary of the flow. Adjunctively, it has been shown that these laws further require that at the beginning of the motion a starting vortex (CD, Figure 7) of strength equal to and opposite to that of the bound vortex, be formed. The Vortex Laws are satisfied by including the trailing vortices BD and AC of strength.
flow within the rectangle ABCD and an upward flow outside it. This flow, however, is unsteady as the starting vortex moves downstream with the flow, and the trailing vortices AC and BD are therefore increasing in length at the rate .
P a g e | 18 Note first, that the velocity induced by a given vortex varies with the reciprocal of the distance from the vortex. Therefore, as time goes on, the starting vortex recedes from the wing position and, soon after the start the velocities it induces at the wing are negligible compared with those induced by portions of the trailing vortices near the wing. In practice, b << t for steady flight and the
configuration becomes essentially an elliptical vortex fixed to the wing and extending to infinity.
Actual finite wings are made up of a superposition of elliptical vortex elements of various strengths (see Figure 8). An infinite number of these elements lead to a continuous distribution of circulation and therefore of the lift as a function of y extending over b/2 < y < b/2. In steady flight, the vortices will in general be symmetrically placed. The trailing vortex lines lying on the xy plane form a vortex sheet of width b extending from the trailing edge of the wing to infinity.
P a g e | 19 From a physical standpoint, Figure 9 can help visualize the formation of trailing vortices. The flow field that develops as the consequence of the circulation around the wing is initiated by an under pressure ( - ) over the upper surface and an overpressure ( + ) over the lower surface.
The indicated flow from high to low pressure at the wing tips signifies the formation of the trailing vortices. In terms of the Vortex Laws and the Kutta-Zhukowski Condition, the formation of the trailing vortices can be expressed as follows: The circulation about the wing is generated as the consequence of the action of viscosity in establishing the Kutta Condition at the trailing edge. The boundary layer that forms adjacent to the surface is a rotational flow resulting from the viscous shearing action; the rotating fluid elements spill over the wing tips at the rate required to for trailing vortices with circulation equal to that around the wing. After leaving the wing tips, the trailing vortices follow the streamlines of the flow and, in conformity with the Vortex Laws, the circulation around them remains constant. Trailing vortices may become visible in the presence of dust and moisture. Figure 11is a photograph of an airplane emitting insecticide dust from its trailing edge. It shows that, because of the influence of the vortex line, the trailing vortex sheet will roll up along the edge to form a concentrated vortex which can be clearly seen in Figure 11.
Notice that the bound vortex with circulation varying along the span represents a wing for which the center of pressure at each spanwise point lies on the y axis. The lift distribution is continuous and the trailing vortices therefore form a vortex sheet of total circulation zero, since the flow field is that of an infinite number of infinitesimally weak elliptic vortices, with the cross section of each being a vortex pair of zero total circulation. The trailing line vortices are assumed to lie in the z = 0 plane and to be parallel to the x axis therefore, the effect on the flow at a given point on the bound vortex is therefore a
Page |2 downwash w, whose magnitude at each point is given by the integrated effect of the circulation distribution on the semi-infinite vortex sheet over the range b/2 < y < b/2 (see Figure 12). The resultant velocity of attack: at the wing has two components and at each point. These define the induced angle
By the Kutta-Zhukowski Condition, the force on the bound vortex per unit span has the magnitude and is normal to V, that is is inclined to the z axis at an angle of given by . This force has a lift
component normal to
In most practical applications the downwash is small, that is small angle and the above formulas become
. It follows that
is a
Although the trailing vortex sheet induces a downwash along the span of a lifting wing, it also induces an up wash velocity field in the regions beyond the wing tips. When another wing flies in such a region, the incoming flow is effectively skewed up by the up wash so that the resultant aerodynamic force will cause a forward thrust instead if a backward drag on the second wing. This phenomenon can be noticed in our daily lives for flying birds. Flock of birds flying in V-shaped formations take advantage of this effect and studies have shown that in proper configurations, savings higher than 50% in the total power required for flight can be achieved as compared to that when birds fly far apart at the same speed. Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
Page |3 In order to calculate the downwash and induced angle of attack at a wing section, we will be referring to Figure 13 which represents the essential features of Figure 11, shown from the top view of the z = 0 plane. Notice that the downwash is assumed to be positive outward.
By means of the Biot-Savart Law we can express the increment of downwash at the point induced by the element of the vortex filament of strength extending from to the downwash is to infinity in the
at
vortex sheet. Thus after integrating and diving by section at the spanwise location :
This equation gives the amount by which the downwash alters the angle of attack of the wing as a function of the coordinate along the span.
Page |4 the angle between the direction of the flow for zero lift (Z.L.L) at a given , the induced angle of attack , and the effective angle of attack . and the flight velocity vector
Page |5 If the airfoil section were on a wing of infinite span, the sectional lift coefficient there would have a higher value of . Therefore, since the absolute angle of attack is determined by wing
where
is a function of
and
is given by
for
from which,
Where c is the chord length of the airfoil (see Figure 5). This equation indicates that the sectional circulation on a finite wing, which is proportional to , is smaller than that of a wing of infinite span, which is proportional to angle of attack is , because of the induced
caused by the downwash (see Fig.13). Then the fundamental equation in its final form
The only unknown in the above equation is the circulation, and its solution for all span wise locations solves the airload distribution problem for a given wing. Unfortunately, its solution can only
be obtained for only a few special cases, the most important of these, the elliptical lift distribution.
Page |6
to a given circulation distribution simply involves the solution of an algebraic equation. A very important case is the elliptical circulation distribution, for this distribution represents the wing of minimum induced drag. Fortunately the properties of wings of arbitrary planforms that do not differ radically from the most common shapes are close to those of the elliptical wing. It is therefore customary to write the properties of wings of arbitrary planforms in terms of the properties of the elliptical wing and a correction factor. If represents the circulation in the plane of symmetry, the elliptical variation of circulation with span is written
at any point along the lifting line is constant if the distribution is at every spanwise location is the same then the
elliptical. Therefore if the absolute angle of attack effective angle of attack is also constant. Thus,
Where
To summarize for wings with an elliptical distribution and constant lift curve slope and absolute angle of attack, the nondimensional sectional properties will not vary along the span. Using these conditions, the product must vary elliptically for
Page |7
Notice that in an elliptical planform only the product hand, for a noon elliptical planform, since is nearly constant,
that is, the wing must be twisted is the equation is to satisfied. This condition could occur only at a specific attitude of the wing. The wing properties are found by integrating the section properties across the span. The wing lift-coefficient is defined as the total wing lift divided by the product of the dynamic pressure
Notice that the wing lift coefficient and sectional lift coefficient are equal when the sectional lift coefficients are constant along the span. Under this condition, the induced angle of attack for an elliptical distribution becomes,
Where
Experiments have shown that the extra power needed to compensate the induced drag is quite significant even at low flight speed. Since for a given lift coefficient the induced drag is inversely Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
Page |8 proportional to the aspect ratio, the extra power can be made smaller by increasing the aspect ratio of the wing. For this reason, slender wings of larger aspect ratio are often observed on gliders, low power light planes, long duration reconnaissance military planes, as well as birds migrating over long distances. For high-lift, high-payload conditions, induced drag is accountable for up to 40% of the total aerodynamic drag coefficient and, as a result, any attempt to improve such flight characteristic is highly sought-after and desirable. For design purposes, it essential to understand that properties of wing-tip vortices change based on the speed, weight and shape of the lift-producing surface. Weight is the main contributor as the vortices strength is virtually proportional to the operating weight of an aircraft and, as a result, to its lift. Great detail needs to be given to the effects of the generation of great lift forces. At the same time it is also inversely proportional to the wing-span over the velocity squared therefore correct dimensioning of the wing plays a major role in the designing wing shapes. So, in general, being that lift induces a large amount of drag which is strongly correlated to the strength of the trailing vortices that have origin at the wing tips of an aircraft, particular attention needs to be devoted to the development of optimized wing tip configurations.
1.3.8 Winglets
We have seen in Figure 9, Figure 10Figure 11 that the vortices trailing behind a finite wing are formed by the communication of the high and low pressure regions across the lifting surface through the wing tips. It has been shown that the trailing vortices induce a downwash velocity field at the wing, which in turn causes an induced drag on the wing. Mounting end plates would not prevent the pressure communication through the wing tips because, as sketched in Figure 7 the circulation of the trailing vortices is the same as that about the wing. Thus during a steady, level flight the strength of the trailing vortices is proportional to the weight of the airplane and it will remain the same with or without the end plates. Experiments (Minnella, Jugas, Rodriguez, 2010. See below) with vertical plates mounted on the upper surface of a wing tips, indicate that the plates could reduce the maximum circumferential velocity of a rolled-up trailing vortex, but with a corresponding increase in the diameter of the core. The total circulation of the vortex appeared to be the same as that of the vortex trailing behind wing tips without the plates.
Although the total strength of the trailing vortices behind an airplane cannot be changed, it is possible to decrease the induced drag of a given airplane by using properly designed end plates, called winglets, to redistribute the strength of the trailing vortex sheet. Flat end plates are not efficient in that Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
Page |9 they cause viscous drag that is large enough to offset the reduction in induced drag. To be fully effective, the vertical surface at the tip must efficiently produce significant side forces that are required to reduce the lift-induced inflow above the wing tip or the outflow below the tip.
A typical winglet is shown above. It is a carefully designed lifting surface mounted at the wing tip, which can produce a gain in induced efficiency at a small cost in weight, viscous drag, and compressibility drag. The geometry of a winglet is primarily by the toe-in (or out) angle, cant angle, leading edge sweep angle, and the chord and aspect ratio of the winglet. Flow surveys behind the tip of a wing with and without winglets by Fletcher (1976), indicate that the basic effect of the winglets is a vertical diffusion of the tip vortex flow just downstream of the tip, which leads to drag reduction. The gain in induced efficiency for a winglet is greater for a wing that has larger loads near the tip. If the winglet was set vertically on the wing tip, it would behave like an endplate, that is, its own normal force would contribute nothing to lift. On the other hand, if the winglet lay in the plane of the wing, its effect would be that of an irregular extension of the span, causing a large increase in the bending moment at the wing root and therefore a weight penalty for the wing structure. In practice, the winglet generally has an outward cant angle so that its influence is a mixture of both effects. The best cant angle will be a compromise between induced efficiency and drag caused by mutual interference at the junction of the wing tip and the winglet. Winglet toe-in angle provides design freedom to trade small reductions in induced efficiency increment for larger reductions in the weight penalties caused by the increased bending moment at the wing root. For high effectiveness of the winglet for cruise conditions, the leading edge of the winglet is placed near the crest of the wing-tip section with its trailing edge near the trailing edge of the wing (see Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 10 Figure 16). In front of the upper winglet mounted above the wing tip, a shorter lower winglet may also be mounted below the wing tip. A lower winglet in combination with a larger upper winglet produces relatively small additional reductions in induced drag at cruising speeds, but may improve overall winglet effectiveness at both high-lift and supercritical conditions. The combined upper and lower winglets mounted on a jet transport wing were investigated in a wind tunnel by Withcomb (1976). It was shown that at a Mach number of 0.78 and wing lift coefficient of 0.44, the addition of winglets reduced the induced drag by about 20% and an increase in the wing liftdrag ratio of approximately 9%. These results clearly showed the effectiveness of winglets.
On January 13, 1982 the first Boeing 757-200 was assembled and on February 19 it did its first successful flight. On December 21, same year, after 1380 hours of flight testing for more than 10 month, the U.S. FAA certified the 757-200. The first delivery of this aircraft occurred next day and was made to Eastern Airlines. Subsequently in January 1983 the British Civil Aviation Authority certified the above aircraft for flight over the United Kingdome. Entering into the Boeing 757-200 specifications we can say it is a midsize airplane with two engines that allows it to operate in a short or medium range flights. It was designed on the final of the 70s by the Boeing Company. Top technology was used in order to bring down noise pollution, increase passenger comfort and operating performance. Although its sales toke about a year to reach high levels this plane has had a versatile adaptation throughout the world. It has been created in several configurations such as freighter or jetliner. It was originally designed to carry 200 passengers in a regular configuration but it can accommodate up to 228 passengers which brings it capacity into the range of the 757-300 and 737-900. Its takeoff weights varies from 220 000 pounds to 255 000 pounds increasing its payload range.
One of the most important technical parameters that highlight the 757-200 design are the high bypass ratio engines from the Rolls Royce or from the Pratt & Whitney companies that combined with the sweptback-twisted wing design makes it one of the quietest more fuel efficient airplanes in the world. The thrust of the above engines varies from 36 600 to 43 500 pounds. Its fuel consumption oscillates around 43 % less per seat than other older trijets aircrafts. The most important technical Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 11 aspects for our objective are being shown in Table 1.1. More in deep technical features are also shown in the Appendix 9.1. The 757 wing has some important changes with respect to Boeings previous designs. For example it is not so swept back but it is thicker at the base allowing a longer wing span. The upper surface is slightly curve than the lower originating a camber wing airfoil and the leading edge is also slightly sharper. These last changes contribute to the lift force and drag reduction producing better aerodynamic performance and burning less fuel. Another important contribution of the wing design is that it allows for the engines to use less power during takeoff and landing procedures. For example with respect to the 737-200, a much smaller plane, the 757-200 can flight for about 1740 nautical miles or 5 500 feet more. Therefore it can reach a cruiser speed of Mach 0.82 much faster than others. Other improvement had been included in the design of the Boeing 757 airplane class, such as the usage of lightweight materials. Aluminum alloys for the wing skins produced a saving of 610 pounds. Graphite or epoxy composites were used in the control surfaces such as elevators, rudder and ailerons. Aerodynamics fairings, engine cowlings and landing gear doors introduced a total weight saving of 1 100 pounds. Another impressive inclusion in the design of this plane is the use of carbon brakes which add time to the service life with respect to the steel brakes and also reduces about 650 pounds in weight too.
Table 1.1: Technical specifications of Boeing 757-200 aircraft serie 757-200 Passengers Typical 2-class configuration Typical 1-class configuration Cargo Engines maximum thrust 200 228 1,670 cu ft (43.3 cu m) Rolls-Royce RB211535E4 40,200 lb (179 kN) Rolls-Royce RB211-535E4B 43,500 lb (193.5 kN) Pratt & Whitney PW2037 36,600 lb (162.8 kN) Pratt & Whitney PW2040 40,100 lb (178.4 kN) 11,489 gal (43,490 l)
P a g e | 12 Maximum Takeoff Weight Maximum Range Cruise Speed Basic Dimensions Wing span Overall Length Tail Height Interior Cabin Width Body Exterior Width 255,000 lb (115,680 kg) 3,900 nautical miles (7,222 km) Mach 0.80 124 ft 10 in (38.05 m) 155 ft 3 in (47.32 m) 44 ft 6 in (13.6 m) 11 ft 7 in (3.5 m) 12 ft 4 in (3.7 m)
In 1990 the Federal Aviation Administration granted 180- minutes certification for the 757-200 of extended-range twin (engine) operation or ETOPS. This certification was given for both type engines this plane has, the Rolls Royce Rb211-535E4, RB211-535C and the Pratt & Whitney PW2000 series. This certification was given as prove of the 757-200s series flight reliability. As an example of this is the fact that the 757-200 can fly 4 500 statute miles with full payload.
Few years later with the increments of the oil and gas prices a new way of increasing flight efficiency was the introduction of winglets. The Boeing Aviation Partners Inc. created blended winglets that reduced about 5 % fuel consumption. They were available for the 757-200 as an addition to the already available 1 030 airplanes. The mechanism of incorporating the winglets was called retrofitting. The next Figure 17 shows some of the basic parts to perform the assembly of winglets into this plane wings and Figure 18 shows a real life winglet assembly components for the 737-200 airplane.
P a g e | 13
Figure 17: Retrofitting mechanism of blended winglets, created by the Aviation Partners Boeing Company
Figure 18: Retrofitting mechanism of blended winglets, created by the Aviation Partners Boeing Company for the 737200
Winglets were made with the purpose of reducing not only the fuel consumption, but more importantly they were meant to reduce the induced drag. The blended winglets were registered by the Boeing Aviation Partners Company at the U. S. patent office on September 20 1994 with the patent number 53482531. These winglets brought more benefits to airplanes than the ones already mentioned. A list of them is in the patent document and we already summarize them below.
P a g e | 14
Built-in fuel hedge Improved takeoff performance Reduced engine maintenance costs Increased payload-range Lower airport noise and emissions Improved operational flexibility Dramatically enhanced appearance Higher airplane residual value
2Some of the most important facts winglets do in favor of the Boeing series of 757 planes are also being named below2. locomotive. fly the 767. Of the company's (year-end 2000) unfilled announced orders for 1,612 commercial jets , 4.9 The surface area of a pair of 757 wings is 1,951 square feet (181 square meters), about the The 757 has carried more than 1.3 billion passengers, more than four times the population
of the United States and Canada combined. In 18 years of operation, the 757 fleet has flown the equivalent of nearly 25,000 roundtrips
between the Earth and the Moon. The 757 fleet has produced over 24 million hours of service for its operators, equivalent to
about 2,750 years of continuous service. The 757 Freighter can hold over 6 million golf balls. At 255,000 pounds (115,660 kilograms), the 757 weighs as much as a diesel train
same as the floor space of a three-bedroom house in the U.S. There are about 626,000 parts in a 757. About 600,000 bolts and rivets fasten those parts
together. The length of all wires in the twinjet is about 60 miles (100 kilometers). Airlines fly the versatile 757 on a wide variety of routes. The twinjet is used to serve city
pairs as far as 4,281 statute miles (6,890 kilometers) and as close as 65 statute miles (105 kilometers). The common 757/767 cockpit type-rating permits flight crews trained on the 757 to also
P a g e | 15 Thanks to all of these benefits and the retrofitting mechanism of winglets it is possible that airplanes that are not longer in production can increase their performance, such as the Boeing 757-200 series. And for those new airplanes some of them already have winglets embedded to their wing as part of their original design. For a wing having an infinitely large wing span, trailing vortices would not be of particular significance as the wing would successfully redistribute and de-strengthen its wing tip characteristics. In modern avionics, however, due to span-wise restrictions which involve maneuverability at airports, aerodynamicists are forced to take into account this flight interference and develop optimized wings that administer this behavior. Recently, it has been found that rather than drastically altering the wing foil in an attempt to improve aerodynamic efficiency, wing tip modifications such as winglets, capably diminish the unwanted trailing disturbances. Winglets are wing-tip devices designed to: trailing vortices. component. Improve the strain distribution of a wing by applying lift components at the tip-sections. Increase the payload capabilities of an aircraft by providing and additional lift Reduce the induced drag component of lift by redistributing and de-strengthening the
Contribute a positive-traction component to the aircraft thereby reducing loading on the propulsion system.
1.3.10 **********KUBRINSKI*******
Surface pressure distribution along the wing is only one of the parameters that go into the design and construction of an optimal wing, and in turn a winglet. For correct design, several factors have to be taken into account; these are span wise load distribution, the local chord multiplied by the sectional lift coefficient because induced drag depends on this. Also the optimal pressure distribution must be enforced through a range of angle of attack, including at conditions of forward slip and side slip. The design of winglets must also include influence of the wing, fuselage, empennage and the location of the center of gravity. Good design must take all these factors into account, with these methods and a fully developed boundary layer around the whole wing surface, a better wing will be designed.
1.3.11 Optimization
P a g e | 16
P a g e | 17
Any function
Due to the uniqueness of this hybrid optimizer code that tethers different algorithms for separate functions, its accuracy and robustness is close to the best commercial optimizers available. Utilizing the RBF for interpolation has the advantage of reducing computational time while still maintaining a high level of accuracy. A detailed analysis of the hybrid optimizer is provided in Appendix The bullets listed below are the main tasks the hybrid algorithm runs repeatedly over several levels of grid refinement. Initially, the optimization procedure starts with a very coarse grid and over the course of multiple iterations, the mesh is refined. 1. Generate an initial population, using the real function (not the interpolated one) f(x). Call this population Preal. 2. Determine the individidual that has the minimum value of the objective function over the entire population Preal and call this individual xbest. 3. Determine the individual that is more distant from the xbest, over the entire population Preal. Call this individual xfar. 4. Generate a response surface, with the methodology in Section 2, using the entire population Preal as training points. Call this function g(x). 5. Optimize the interpolated function g(x) using the hybrid optimizer H1, defined above, and call the optimum variable of the interpolated function as xint. During the generation of the internal population to be used in the H1 optimizer, consider the upper and lower bounds limits as the
P a g e | 18 minimum and maximum values of the population Preal in order to not extrapolate the response surface. 6. If the real objective function f(xint) is better than all objective function of the population Preal, replace xfar by xint. Else, generate a new individual, using the sobol pseudo-random generator within the upper and lower bounds of the variables, and replace xfar by this new individual. 7. If the optimimum is achieved, stop the procedure. Else, return to step 2.
The driven component for this methodology is the particle swarm method. Particle Swarm method is based on the social behavior of various species and tries to equilibrate the individuality and sociality of individuals to seek the optimal interest.
1.3.11.3 Particle-Swarm
The Particle Swarm Optimization method (PSO) was introduced by Kennedy and Eberhart3 and it is based in the intelligent unite behavior of the organisms in a swarm to reach a collective goal; when at the same time the behavior of a single organism in the swarm seems completely inefficient but it is intended to find its particular best solution to the global problem. This method is very useful when optimizing unconstrained functions but, if a number of constrains are added the problem turns to be more complicated. Therefore several approaches had been introduced such as penalty, repair, and constraint-preserving methods4. How is this algorithm implemented? Well, let say that a particle xi has memory of which one is the best solution yi that has being found and it travels through the search dominium with a velocity vi. If this velocity is continuously adjusted with respect to its particular best and the global best solution found by the rest of the swarm them we define the swarm as:
(1)
With i = 1, 2, 3 After each iteration of the PSO algorithm, the best particular solution yi of each element is compared to its actual performance and set to a better performance. So if the function to be optimized is defined as we can find yi as the next equation shows.
(2)
P a g e | 19
The general best solution is updated to the position with the best performance within the swarm with the next formula:
(3)
Now the particles velocity and position are updated separately for each dimension j, by the next formula:
(4)
and
1. search space. 2. 3.
Set the iteration number t to zero, and randomly initialize swarm S within the
of each particle.
Compare the personal best of each particle to its current performance, and set
to the better performance, according to equation (7.2). 4. Set the global best to the position of the particle with the best performance
within the swarm, according to equation (7.3). 5. 6. 7. 8. Change the velocity vector for each particle, according to equation (7.4). Move each particle to its new position, according to equation (7.5). Let: .
P a g e | 20 In most multi-objective problems, including this one, seeking the optimal solution and the range of solutions is driven by dominance. Comparing two different solutions, this dominance elects the better solution, taking into account both objectives. This can be stated as the following, Solution 1 is said to dominate solution 2 if: 1. 2. The solution 1 is no worse than 2 in all the objectives The solution 1 is strictly better than 2 in at least one objective.
If either solution 1 or 2 is not better than the other on the basis of the above statements, they are referred to as non-dominated with respect to one another. Figure 19 illustrates the above statements.
Figure 19 shows that alternative 1 is non-dominating with respect to the other solutions. Solution 1 is better than the other three in objective f2 but worse in objective f1. Solution 3 is equal to solution 4 for f2 and worse than solution 4 in objective f1; therefore solution 3 is dominated by solution 4. Solution 2 is dominated by both 3 and 4 because it is the least desirable in both objective f1 and f2. When two solutions are independently non-dominated by a third solution, it is not necessary that the former two solutions be non-dominated with respect to each other. The compatibility of tradeoff solutions in multi-objective problems cases shows is demonstrated by non-dominance. Most multi-objective optimization algorithms use a population of decision variable sets that search for optimal sets. The two main sets this population can be divided into during any generation is:
P a g e | 21 1. The non-dominated set, which is composed of solutions that are not dominated
by any other solution in the whole population 2. dominated set. The set of solutions belonging to the non-dominated set during a certain generation for a surface called the Pareto front. The Pareto front can be visualized as a curve in a 2-D objective problem and as a 3D object in case of a 3 objective problem. Solutions that are not dominated by any other solution in the whole feasible space are known as globally optimal solutions. The Pareto front comprised of these solutions is termed the global Pareto front. The dominated set, which is composed of all the solutions excluded from the
Figure 20 illustrates four different kinds of Pareto fronts for a problem with 2 objectives. To have flexibility in an optimal design it is required to compute a set of solutions that are biased towards one or more objectives. Achieving a uniform distribution of solutions over the whole range of the global Pareto front is important, because it demands the presence among the members of the non-dominated population set.
P a g e | 22 All CFD studies performed throughout were done using a Linux based, open source software called OpenFOAM (Open Field Operation and Manipulation). OpenFOAM is a software package with applications in the engineering and science fields. Its diverse uses across many disciplines and it being open source makes OpenFOAM a very important tool for an engineer. It is capable of solving for chemical reactions, turbulence, solid dynamics, electromagnetics and finance.
Open source, Linux software gives the user an advantage that is not present in standard programs like ANSYS and SolidWorks; this being that the user can freely modify any aspect of the software that he or she deems necessary. To someone who is well versed in programming and CFD this is critical, this means that he or she can customize the software to suit their needs. Another advantage of OpenFOAM is that it is free. While student versions of modeling software that perform CFD analysis are available, the meshers for these have a limit on the number of vertices that can be applied on the domain. A mesh is a collection of vertices, edges and faces that is unstructured and in the shape of a grid; this grid defines the shape of an object. The shape of the faces of the grid varies for each mesher, OpenFOAM uses hexahedral polygons for its faces. When performing CFD analysis in the field of aerodynamics, a large domain box is desirable. For this reason, to obtain coherent results, a large amount of vertices of this grid are needed. Using student versions of ANSYS or SolidWorks, the number of nodes available is set at 1 million nodes or vertices. For small domains, this will generate a mesh fine enough to give an accurate analysis. However since the limit is set at 1 million nodes, when these elements are spread out over a large domain box, the mesh becomes too coarse and results will not coincide with experimental values. In contrast to these other software, OpenFOAM has no limit on the number of nodes when meshing. When setting up the case experiment, the user specifies how many nodes he or she wants the mesher to use for the object and domain box. For meshes greater than 1 million nodes the mesher should be run on a computer cluster. OpenFOAM has a limit when meshing, no more than a million nodes per processor. So, if 3 million nodes were desired to achieve a fine mesh, OpenFOAM would be run on 3 processors that are connected with a parallel computer network. In theory, if one has a computer cluster at their disposal, there are no limits to the number of nodes used to define a surface and domain. Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 23 While OpenFOAM is very advantageous in terms of the quality of CFD you can perform, it does have its disadvantages, one of these being that it is not user friendly. Most CFD software has a GUI based program that is user-friendly and is designed for ease of use. OpenFOAM lacks this; it is comprised of C++ files that are created and modified by the user to suit his or her needs. OpenFOAM has stored functions that are called up by the user writing different files written in C++ programming language; these files are called dicts. Each specific function for OpenFOAM has a different dict, which can be entirely modified. So depending on what analysis the user wants to run, he or she writes and modifies those specific dicts. Figure 22 shows a sample dict for snappyHexMesh, OpenFOAMs mesher, as is seen the file is written entirely in C++ so a strong background in programming is a prerequisite. Within this dict file is where the options for snappyHexMesh are modified: refinement region, level of desired refinement and mesh layering.
Figure 23 shows the structure for a sample CFD case, this structure will vary slightly for a different discipline. Within the case directory there will be two main folders, one folder for the mesher and one for the solver. The mesher folder contains the dicts for blockMesh and for snappyHexMesh, also the surface being analyzed. The solver directory is split up into three subparts, the 0, constant and system folders. The 0 directory contains all the initial conditions for the case; initial conditions include
P a g e | 24 the pressure, temperature and velocity fields. Depending on what conditions want to be studied, these are changed accordingly. The constant directory holds the dict file for the solver and within the System branch goes the controlDict. The control dict is the file that dictates the time step, max courant number, start time and end time for the analysis.
Case Directory
Mesher
Solver
Constant
System
Constant
System
blockMesh
snappyHexMesh
Initial Conditions
rhoCentralFoam
controlDIct
To help users become acquainted with the software, there are very instructive tutorials and online guides that go in depth and help users set up sample cases. There are sample cases are for different disciplines that guide the user, and give a general idea as to which of OpenFOAMs functions will have to be used so that those dicts can be written and modified.
P a g e | 25
The size of this domain is determined by what needs to be studied. For research on winglets, to study the effects of wing-tip vortices and curtain effect, the domain box should extend at least seven chord lengths behind the wing. The domain box should start at least two chord lengths in front of the wing, for the flow to fully develop and to properly analyze the stagnation point. The reason for this being that the effects of induced drag are only noticed very far behind the wing and any reduction from the curtain effect will only be noticed from this distance. A good rule of thumb for choosing the height of the domain box would be forty times the height of the wing. A domain box of these parameters is sufficient to perform a correct analysis of the wake left by the wing. The values of the domain, min (x, y, z) to max (x, y, z), are input into the blockMeshDict. This file is simply a dictionary written in C++ that controls blockMesh, and this file is provided in appendix. After constructing the domain box, the next step is to mesh the object and the domain box. OpenFOAM reads the object being analyzed as a STL file and refers to it as a triSurface. STL is a format from stereolithography CAD software. This extension is commonly used for computer-aided manufacturing and rapid prototyping. SnappyHexMesh is a mesher that uses hexahedra and splithexahedra elements to mesh iteratively around a given surface. For snappyHexMesh to start, a point inside the domain, a location (x, y, z) anywhere inside the domain but outside the triSurface has to be specified. With this location, snappyHexMesh can find the triSurface, mesh around it and run successive iterations around the surface until the level of specified refinement has been fulfilled. Figure 25 shows how the mesh conforms around the triSurface; the darker grey area is the refinement box. If a certain area inside the domain requires more extensive analysis a refinement box can be specified. Everywhere inside this box the mesh will be finer allowing for a more detailed examination. As stated in the literature review, the effect of winglets are noticed very far downstream, so it is desirable to specify a refinement box around this region, for more accurate results.
P a g e | 26
Observing Figure 25, it is noticeable that the inside of the triSurface is actually meshed on the inside. The way snappyHexMesh operates is that the surface is meshed iteratively with hexahedral elements that penetrate the surface, and in the final stage of meshing these elements are snapped to the surface of the object. This final stage, Figure 26, allows for a more detailed and finer mesh that isnt equipped in other CFD software. Another advantage of this software that isnt present elsewhere is that there is no limit to the number of nodes that OpenFOAM uses to mesh. Other software programs such as ANSYS and SolidWorks have a limit to the number of nodes the mesher uses. For the CFD analysis performed in this research, a large domain box is needed to study the resulting vortices far downstream of the plane, for this reason if only a small amount of nodes are used, the results obtained using SolidWorks or ANSYS will not be accurate.
P a g e | 27
Where L is the lift force, is the density of air, v is true airspeed and A is the planform area. Planform area can be calculated as half of the surface area of the wing. In the case of fixed-wing aircraft the wing is the only lifting surface and lift is perpendicular to the flight direction, so the wing is the only structure to consider when calculating for planform area, the fuselage, horizontal stabilizers and winglets are not taken into account since they produce little to no lift. To better visualize the planform area it can be thought of as the area of the wing as viewed from above the plane.
Where FD is drag force, is the density of air, v is the true airspeed and l is the mean average chord length. For a rectangular wing, the mean average chord length is simply the chord length because there will not be a variation in the length of the chord. However, for a wing where the chord length varies this value can be calculated as the planform area divided by the wingspan.
Where M is the pitching moment force, q is the dynamic pressure and l is the mean average chord length. To calculate the coefficient of moment, OpenFOAM also requires that the center of rotation, or center of pressure, be inputted. For a rectangular wing the center of pressure can be estimated to be the center of gravity of the wing; since there is no change of the chord length along the span of the wing, pressure will be acting at this point. For a wing with a varying chord length, swept forward or back wings, the center of pressure is calculated to be 25%-30% of the chord length from the leading edge. Another value that OpenFOAM requires is the vector value of the pitch axis. Pitch axis is the axis about which the wing will pitch and can also be visualized as the axis that goes through the center of rotation and is perpendicular to the long axis of the plane.
P a g e | 29 access the MAIDROC one only needs to be connected to the internet, so one does not have to be onsite. Once access is granted to the MAIDROC the user can then patch into the Tesla Computing Lab. Using a secure shell, the user can upload their zipped case file directly into the Telsa, of course to do this, a user account at the MAIDROC is needed, the command to upload a sample case into the Tesla, i.e. scp solver_Optimizer_13.tgz winglets@maidroc.fiu.edu:/home/winglets/case_studies scp, is a command for secure copy and is a Linux function. Solver_Optimizer_13.tgz is the zipped case directory that is being uploaded into the case_studies directory for the user winglets.
P a g e | 30 Figure 29 shows a diagram of the Tesla Computing Lab at FIU. The front-end workstation, Figure 27 acts as the security checkpoint for the Tesla that queries the user name and password for anyone trying to access the lab. The queue master is the head node that distributes the cases between the nodes, it acts as the supervisor of the cluster telling individual nodes which cases to run. Each node pictured below has 2 processors, there are 64 nodes, and therefore the Tesla has 128 processors.
OpenFOAM has a function that decomposes one domain into several subdomains, this way it can be run in parallel. Figure 30 gives a good visualization as to how a domain is decomposed. It helps to visualize the domain of the case as a cube. Now depending on how many nodes are desired to be used, the domain is split evenly. In Figure 30, the domain is split into 27 cubes, it is split 3 times in the x, y and z direction, so for this example 27 nodes will be used to analyze each subdomain. Since each node now has a very small domain to analyze, convergence of the case will be reached very rapidly. The number of subdomains to split the job into depends on how refined the mesh of the body is and the computing time desired. For a faster computing time the more subdomains the domain is divided into the faster the case reaches convergence. Along the faces where each domain touches another, processors will communicate with each other to analyze sections of the mesh that are at these intersections. This type of parallel computing, where nodes of the cluster communicate with each other many times each second is referred to as fine grain parallelism and is the hardest to program for.
P a g e | 31 There are three main types of parallel computing, these are: fine grain, coarse grain and embarrassing parallelism. A computer task is fine grain parallelism if subtasks, communicate between each other many times per second. If the subdomains communicate very few times between each other each second, it is referred to as coarse grained parallelism. Embarrassingly parallel computing are the easiest to parallelize, because subtasks never communicate with each other.
After the job has been decomposed the final stage is to submit the job to the task manager. This is accomplished by using the qsub command. The most common form to do this is by writing a shell script that is called up by the qsub. Figure 31 shows a sample shell script written in C++. The task manager is a feature of the Tesla-128 that comes with its operating system of Rocks 5.1. The task manager keeps track of jobs submitted and keeps job in queue when all the nodes are already running previous cases.
P a g e | 32
P a g e | 33
Table 1.2:
Source of relative velocity Moving model, stationary air Stationary model, moving air
Safety
Instrumentation
Months
any physical equation can be expressed in terms of dimensionless combinations of the variables. Therefore, and function of N variables
products
and one other, whereas K is equal to the number of fundamental dimensions required to describe the variables P. If the problem is one in mechanics, all quantities P may be expressed in terms of mass, length, time, and K = 3. In thermodynamics, all quantities may be expressed terms of mass, length, time, and temperature, and K = 4. The arbitrarily selected set of K variables may contain any of the quantities of , with the restriction that the K set itself may not form a dimensionless combination. When considering the force experienced by a body that is in motion through an idealized fluid, assume that the force will depend on the following parameters:
Symb ol F V l a Name Force Density Velocity Size of the body (chord length) Coefficient of viscosity Speed of Sound
Dimensi on
There are six variables and three fundamental dimensions therefore by choosing the K set, the product become
, and as
The
applying this condition we obtain Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 35
The above equations represent similarity parameters used in aerodynamic testing. Aerodynamic forces are inertia forces, meaning that they result from the model changing the momentum of the moving air. The model changes the velocity or direction of the airflow, or both, if aerodynamic forces are present. Reynolds number is the key factor for wind tunnel testing. To reasonably expect two tests to produce comparable data, we must insure that the tests were run at or near the same Reynolds number. Mach number is not significant in low speed testing because, by definition, compressibility does not have a noticeable effect on the obtained data. Froude number involves gravity and is important in testing free flight models, for which we do not currently have equipment. In summary, in low speed testing we desire to accomplish tests at
An expedient for calculating Reynolds number, Figure 32 gives values for pressure and temperature. The value at sea level standard atmosphere conditions is .
as a function of air
P a g e | 36
Figure 32:
Models of different sizes tested at different conditions of velocity, temperature, and pressure should produce the same force coefficients if the flow patterns around the models are geometrically similar. This will occur if the test conditions are such that the similarity parameters are the same for all model tests being compared.
P a g e | 37
A closed circuit tunnel employs a duct which guides the air around a closed path, resulting in air continually recirculating through the test section. It is also called a Prandtl tunnel, after pioneer aerodynamicist Ludwig Prandtl. A diagram of a closed circuit tunnel is shown in Figure 34 below.
A few parameters must be defined: Test section or jet area in which the model is normally mounted for testing. Diffuser any diverging passage, but specifically the one immediately
downstream of the test section. Bellmouth, entrance cone or extraction cone the converging passage
immediately upstream of the test section. Fan the propeller which moves the air through the tunnel.
There are some other classifications of for wind tunnel types which are used frequently. The test section may be open or closed, meaning the test section is enclosed by walls. The presence of walls, however, prevents realistic deflection of the moving air for tests of models which deflect the air by a large amount. Tilt engines, very high lift wings, and helicopters fall into this category. For this class of
P a g e | 38 testing, test section walls are not used. The result is an open jet or open test section tunnel. Both open circuit and closed circuit tunnels may be open test section. Tunnels are sometimes classified by the cross-sectional shape of the test section. Common shapes are round, square, elliptical, rectangular, and octagonal. Rectangular is probably the most common, though in many cases a rectangular test section has fillets in the corners which render the section actually octagonal. A height to width ratio of 7x10 is very common for rectangular sections. There are several types of special purpose tunnels which deserve to be mentioned. Probably the most common special purpose tunnel is a smoke tunnel. A typical one is shown in Figure 35. The frequently have very narrow test section, used only for visualization of flow around a short span segment of airfoils. The tunnel used was built with a 18x24 inch test section allowing visualization of three-dimensional flow fields, particularly tip vortex patterns. Smoke is injected into the airstream from a row of parallel tubes. The smoke is generally not smoke at all, as it is usually oil vapor created by electrically heating thin oil until it boils. Burning of materials which produce real smoke is messy and hazardous. In order to keep the smoke streams clearly defined, it is necessary to have steady laminar flow. As a result, smoke tunnels are frequently very low speed with a large entrance cone and many turbulence- damping screens and/or honeycombs. The tunnel used seemed to operate best at an airspeed of about 5 feet per second and its maximum speed is about 30 feet per second.
Variable density tunnels are constructed so that the entire circuit is a pressure vessel. They can be pressurized and/or cooled to produce higher air density, facilitating high Reynolds number testing. Or, some can be evacuated to lower pressure, which allows high Mach number testing with less power. These are obviously very complex and expensive facilities. NASA Langley complete construction in 1982 Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 39 of one which they call the National Transonic Facility (NTF). It can be pressurized to nine atmospheres and uses liquid nitrogen to cool the air to . It has an 8.2 ft. square test section. Industry and
government tunnel are generally much larger than privately owned ones, but sill they are not large enough for full scale models. There are two very large tunnels called full scale tunnels in the United States. NASA Langley has one with a 30 x 60 foot section, and NASA Ames has a 40 x 80 foot test section. The Ames tunnel is the worlds largest and has completed construction, also in 1982, to add a new 80 x 120 test section. There are a few tunnels with vertical test sections called spin tunnels. They are used for testing spin characteristics of free flight models, and sometimes for parachute testing. Tunnels specifically built for testing airfoil models which span the entire test section from wall to wall are called two-dimensional tunnels. Most airfoil data in standard texts and reference books is acquired in this type tunnel. With the emphasis on reduction of fuel consumption in the automotive industry, there is currently much research being done on aerodynamic reduction. Many automakers are presently doing wind tunnel work in Lockheeds large wind tunnel in Marietta, Georgia, though a couple have their own tunnels. Closed circuit tunnels are more prevalent than open circuit. Open circuit tunnels are simpler, and thus cheaper to build. The problem with them is that due to large size, the inlet must usually be outside the building which encloses the test section. This means that the air being drawn into the tunnel is subject to weather: wind gusts, rain, insects, dust, temperature, humidity. It is also easy to picture that open circuit tunnels require more power than closed circuit. Closed circuit tunnels get to capture and recycle some of the kinetic energy of the air, while open circuit tunnels just dump the moving air into the surrounding atmosphere. The additional power required, typically 10-15%, for an open circuit usually does not justify the cost and space required to build the rest of a closed circuit. It is control of the quality of the air going through the test section that throws the decision in favor of a closed circuit.
Total pressure = Static Pressure + dynamic pressure It is clear that for this expression to make sense, we must make a habit of distinguishing between various types of pressures. We also need to distinguish between these free stream properties Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 40 and surface pressure on any model we might be testing. Different instruments are used these types of pressures, and particular care must be given when choosing the proper one.
So, to measure static pressure accurately, we must be careful to prevent any accidental inclusion of the part of the dynamic pressure. We do this by making sure that the static pressure hole is in a surface parallel to the velocity direction. This can be easily accomplished in wind tunnel by simply drilling a hole in the wall of the tunnel. The air has no choice but to flow parallel to the wall. The second consideration is that the local velocity at the pressure measurement location must be the same as the free stream velocity. Once again, this is fairly easy to determine in a wind tunnel. As long as no rapid changes in wall shape occur near the static pressure hole, the local velocity will be the same as the free stream (outside the wall boundary layer, of course). And, the static pressure at the wall is the same as at any point in that cross-sectional plane. Use of a probe for measuring static pressure is not quite so easy. A simple static pressure probe could be made by drilling a hole in the side of a tube with the leading edge plugged. The same two problems mentioned above must be dealt with, though. If the probe is not perfectly aligned with the flow, the static pressure reading will be in error. It will be high if the hole is on the upwind side and low on the downwind side. The problem is corrected fairly well by using eight holes equally spaced around the circumference of the probe body. These all feed into a common manifold, which almost cancels out the misalignment errors on the opposite sides. A typical pitot-static probe is shown below.
The second problem is that of insuring that the local velocity is equal to the free stream velocity. The fore-and-aft position of the static holes takes care of this requirement. The local velocity is high, and Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 41 static pressure low, near the tip of the probe due to crowding together of the streamlines as they flow past the tip. The static holes are a safe distance downstream of the tip to avoid locally high velocity. However, the holes cannot be too close to the stem because the local stagnation of air against the stem reduces local velocity and raises static pressure. Probes are commercially available in many diameters, with inch being the most common.
pressure. Static pressure is much more sensitive and 5 diameters seems like a minimum safe distance producing about 1% error.
P a g e | 42 We use manometers for most of our pressure measurements because of the fact that manometers are primary standards, and because most of the performed experiments require measurement of relatively few pressures. It is more typical of industry testing to use electrical sensing devices called transducers to measure pressure. These devices can be read and are frequently wired directly into analog-to-digital signal converters which in turn send the digital signals directly into the data reduction computer. Calibration and maintenance of this equipment is a demanding task.
1.3.13.10
Tufts
Tufts are the easiest to use and are probably the most common. They are particularly
useful in finding regions of separated flow. Tufts can be almost any light and flexible threads or yarns that are usually taped to the surface of the model. In very low speed flow, spanwise strips of tape are suitable and the tufts must be very flexible so that the drag of the tufts will pull them with enough force to make them trail in the local flow direction. Thus, tufts clearly show local flow direction when the boundary layer is not separated. For high speed flow, the strips of tape are less likely to blow loose if they are aligned chordwise and must be made out of stronger material in order to avoid breakage.
P a g e | 43
Tufts are usually a contrasting color with the surface for improved visibility. Still photos at a relatively slow shutter speed (about 1/50 second) will show clearly defined tufts where attached flow has blown the tufts tightly back along the model surface. Separated flow will cause the tufts to wave around, and they appear blurred in the photos. Tufts can be further implemented with the use of whisker pole which is comprised of one or two tufts on the end of a long pole allowing the tuft to be held briefly in whatever position is desired.
1.3.13.11
Smoke Flow
Most smoke generators for low flow speed heat up oil until it vaporizes, then inject the vapor into the air flow in several parallel streams. If the smoke density is adjusted so that it has no tendency to either sink or drift upward, the smoke streams will closely approximate streamlines in the flow pattern.
Photography is again a beneficial addition to this flow visualization method. Thus, the inside of the test section must be painted flat black for contrast. Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 44
1.3.13.12
Airfoil Testing
The term airfoil data refers to the results of tests on a constant chord model which spans the test section from wall to wall. It is synonymous with two-dimensional data and also with the airfoil section data. Aerodynamic force coefficients measured in this manner are denoted by lower case subscripts.
1.3.13.13
height about 2.5 4 times their width. For high angle of attack tests, the airfoil should have a chord less than 40% of the test section height. For low angle of attack data, a chord less than 70% of the height is sufficient to avoid unduly large wall interference effects on the measured data. When measuring velocity profiles in the wake of an airfoil to determine momentum loss, the most accurate and convenient measurement device is a total pressure rake with a static pressure tap in the wall at the same cross-sectional plane as the tips of the total pressure probes. Because the static pressure in the airfoil wake may not be the same as free stream static pressure right at the trailing edge of the airfoil, proper positioning of the total pressure rake of at least 0.7c downstream of the trailing edge to give the wake static pressure a chance to equalize to free stream static pressure.
1.3.13.14
several key differences must be accounted for: The spanwise lift distribution must fall to zero at the tips of the wing. Therefore,
even though they use exactly the same airfoil shape, a finite span of wing will have a maximum lift coefficient only about 90% of that of a twp-dimensional wing. A finite wing span, or finite aspect ratio wing has tip vortices and an
accompanying increase in downwash. The velocity distribution in the tip vortex also causes an angle of attack variation across the span. The result is a sharply reduced lift curve slope, . It can be calculated by
The shorter chord at the tip of a tapered planform produces a lower Reynolds
number at the tip compared to at the root, making the tip likely to stall at a lower angle of
P a g e | 45 attack. This results in roll control problems unless the wing is somehow adjusted to correct it usually twisted about 2 degrees. Finite span or 3-dimensional wing data is denoted by using upper case .
1.3.13.15
There are three ways to measure forces on a model in a wind tunnel. Forces on the model can be retrieved by using an instrumented model mounting system called a balance as shown in the picture below.
1.3.13.16
Aerodynamic forces on an airfoil are accompanied by a change in momentum of the air flowing over the model. It is possible to measure the change in momentum of the moving air and calculate the force which must have existed to produce the change in momentum. This method works particularly well in the case of drag on streamlined bodies like airfoils, as long as no large separation regions exist. Separation includes recirculating flow, which brings exchange of angular momentum into the problem. Considering linear momentum only, Newtons second law states that force equals the tie derivative of momentum. In the case of streamwise component of the momentum,
P a g e | 46
; V is volume and
Substituting the definitions of dynamic pressure, q, specialization of the obtained drag equation. Notice that the model. Outside the wake, terminology by which equation: ;
, is different from
is the same as
Thus, if dynamic pressure is measure as a function of vertical position within the airfoil wake, we can calculate fairly easily.
P a g e | 47
Chapter 2
This chapter covers the division of responsibilities by team member along with the time management guidelines set up in order to successfully reach the project main and partial objectives. A more detailed explanation of each objective will be carried out in the upcoming sections of this project.
2.1
Overview
Within recent times, significant improvements have been brought about by the worldwide
scientific community in the field of aerodynamics. Particularly, aerodynamic efficiency has been a hot topic for quite some time, and the first commercial applications of efficiency-inducing aerodynamic components have been steadily appearing on the market. Soaring fuel prices combined with technological advances in the field of computational fluid dynamics have obligated aerospace and aeronautical engineers to develop and test innovative design methodologies capable of delivering aerodynamically-efficient and cost-effective designs. This project has been formulated with the intent of exploring the field of aerodynamics, and to develop knowledge and skills necessary to design an aerodynamic component capable of improving aerodynamic efficiency. Different fields such as the aerospace, aeronautical, and automotive would gladly welcome initiatives such as our own, however, in an attempt to link the pursued mechanical engineering bachelors degree to a specialization in aerospace engineering, this project concentrated on airplane applications. The intent being, improve the aerodynamic efficiency of a Boeing 757-200 commercial aircraft by the implementation of wing tip devices called Winglets.
2.2
Project Objectives
The design and implementation of elliptic winglets to an existing Boeing 757-200 airplane, in an
standard configuration without Winglets, and by 2% with respect to the standard configuration with Winglets. In order to fulfill the above main objective the elliptical winglet optimization procedure will be implemented first into a NACA 2412 airfoil with the same planform area as the 757-200 wings and with the same average chord length. This partial objective is necessary to be carried out first to save computational time in the validation of the optimization algorithm we decided to use.
P a g e | 48
2.3
Design Specifications
Elliptical Winglets are parameterized according to the Lame equation shown next and the
Where a, is the winglet total addition to the wing span and b is the total height of the winglet. The exponent n will define de radio of curvature of the winglet. A total of 5 variables or parameters are necessary to define and design an elliptical winglet. The other 2 parameters are the tilt back angle () of the winglet and the chord length of the winglet tip airfoil (cw). All of these parameters are being shown in the next figure for better understanding.
Multi-objective optimization is performed on 100 randomized-parameter configurations within prescribed limits (see optimization results). CFD is performed and compared to wind tunnel testing on the 3 optimal Winglet configurations. Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 49
2.4
degrees angle of attack at an altitude of 6000ft. (air properties are based on altitude). Payload is *****
Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Part Winglet Camber In Winglet Camber Out Winglet Symmetrical Airfoil NACA 2412 Wing 18'' NACA 2412 Wing 12'' Original Boeing 757 Winglet Optimal Boeing 757 Winglet Optimal Winglet #1 Optimal Winglet #2 Optimal Winglet #5 Boeing 757 Wing West System Marine Epoxy Slow Hardener Embry-Riddle Wind Tunnel Testing
Application NACA 2412 Wing 18''/12'' NACA 2412 Wing 18''/12'' NACA 2412 Wing 18''/12'' Wind Tunnel Smoke Tunnel Boeing 757 Wing 19'' Boeing 757 Wing 19'' NACA 2412 Wing 18''/12'' NACA 2412 Wing 18''/12'' NACA 2412 Wing 18''/12'' Wind Tunnel Manufacturing Manufacturing Testing Total=
Totat Price $ 23.3 23.3 23.3 140 70 23.3 23.3 23.3 23.3 23.3 218.36 81.29 42.77 875 1613.82
P a g e | 50
Chapter 3
Design Parameters
The elliptical winglet approach we will take in order to create the optimal winglet configuration for the Boeing 757-200 aircraft will be based in the Lame equation presented in chapter
3.1
drag. The best method for reducing these vortices is attaching endplates at the wingtip, so as to dissipate the flow of high to low pressure. After knowing this, a preliminary study must be done to determine which basic configuration of endplates will provide the best CL/CD ratio. Based on an extensive literature review, three main parameters for the design of a winglet were determined. These three parameters were: the transition from the wing-tip to the winglet, whether the winglet goes straight up or down and finally the camber of the airfoil of the winglet. Each of these key parameters has several alternatives and to determine the best configuration of all three parameters, CFD cases have to be setup and analyzed to determine the best combination. The alternatives for the transition of the winglet were whether it will be a blended, ellipitical or wing-tip fence. The second design parameter is to determine whether the best performing winglet is one that points up or down. Finally, the last parameter also has two alternatives. The alternatives are whether the camber in the airfoil of the winglet point towards the fuselage, camber is in, or away from the fuselage, camber is out.
3.2
Design Parameter 1
For the design of the optimal winglet, three different existing winglets were analyzed and rated
to see which one is the best all-around design so that it could be improved upon. The winglets that to be considered were, wing-tip fence, blended and blended elliptical winglets.
P a g e | 51 Table 3.1 is a chart comparing all the winglets to the standards we chose as the most vital for a desired winglet, they are payload contribution, de-strengthening of vortices, positive traction component, wing flutter, retrofitting capabilities, manufacturing, housing capabilities. These were the characteristics to look for in a desirable winglet and the scale for the comparison ranges from -5 to 5.
In this comparison, the most efficient and desirable winglet is a blended elliptical winglet. While it causes some wing flutter, it is the winglet that most contributes to adding a positive traction component, and de-strengthens wingtip vortices in turn reducing induced drag.
3.3
Design Parameter 2
The second design parameter is whether t the winglets will be vertically up and vertically down.
Modern planes all have winglets that are vertically pointed up, but it is advantageous to know how winglets that are vertically down will perform, this test is performed to better understand the concept of induced drag and how winglets destroy these vortices. The setup for analysis consists of three cases: a simple sweptback wing, no winglets, the same wing with vertical upward winglets and lastly the same wing with vertical downwards winglets. To avoid bias of any kind, both winglets constructed for these cases have the same airfoil and no transition from wing-tip to winglets. So they can be thought of as end-plates attached to each wing-tip. This is done to Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 52 just focus on the fact of which end-plate is more effective; a vertical plate that goes above or beneath the wing and if so which is the most effective. These three cases all have the same initial conditions. Since wingtip vortices are more prevalent at take-off conditions for low speed and high lift conditions, the wings will be run at a Mach number of 0.3 and at 6,000 ft. The pressure and temperature of air at this height is 81.22 kpa and 276.26 K respectively. Speed was calculated to be 99.96 m/s for a commercial airplane at this height. 3.3.1.1.1 Analysis of a Simple Swept-Back Wing A simple swept-back wing refers to the fact that this wing has no attachments like winglets, leading or trailing edge devise and no flaps. It is just a plain wing with a varying chord length along the span.
Table 3.2: Parameters for Winglets Up/Down
Parameter Mach Number (M) Angle of Attack () Pressure (p) Height (h) Temperature (T) Density of Air () Kinematic Viscosity () Free Stream Velocity (U) Planform Area (Aref) Mean Aerodynamic Chord (Lref) Wing Span 0.3 5.0
Value
81.22 KPa 1830 m (6000 ft) 276.26 K 1.2798 kg/m3 0 m2/s 99.96 m/s 151.9 m2 5.367 m 28.3 m
Center of Rotation (Center of Pressure) (5.14, 2.856, 14.336) Lift Direction (Vector Value) Drag Direction (Vector Value) Pitch Axis (Vector Value) # of Nodes on Cluster (0, 1, 0) (1, 0, 0) (0, 0, 1) 10
P a g e | 53 Table 2 shows all the parameters that were input into OpenFOAM so it can solve for coefficients of lift, drag and moment. These parameters were kept constant for all three cases of simple wing, winglets up and winglets down.
Table 3 contains the values of the domain box that was constructed for the simple swept-back wing. Since winglets up and down were constructed at the wing-tip of this same wing, the domain box was kept constant for all three cases. Figure 9 shows the domain box for the case of a simple sweptback wing. This will be the control case to compare with the experimental cases, winglets up and down. If the lift over drag ratio improves with the winglets attached at the wing-tip then it is proves that these do indeed serve a purpose. Once it is determined that winglets improve the flight characteristics of a plane the best configuration of a winglet will be determined.
Using rhoCentralFoam, the compressible flow solver for OpenFOAM, this case ran until convergence, this can be proved by plotting the residuals from the solver with respect to time. Residuals Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 54 are simply the error from a result and when the residuals become higher in order, this means that the solution is no longer in a transient state and has reached steady-state. As shown in figure 10, the residuals have reached an order greater than 10 and the plots of both Uz and Uy have plateaued.
Figure 45 shows the Trefftz plane of the pressure field ten meters behind the wing. A Trefftz plane is a plane that is downstream of an aircraft and is perpendicular to the wake. Observing figure 11, the wing-tip vortices are clearly shown in the Trefftz plane.
P a g e | 55
Table 3.4: Forces for Simple Swept-Back Wing
Force Functions Coefficient of Lift (CL) Coefficient of Drag (CD) Lift/Drag ratio (CL/CD)
Streamlines were applied to each wingtip to study the vortices at these locations. Observing Figure 46 the streamlines are shown as round concentric circles. This figure is important because when winglets are attached to each wing-tip the change in the streamlines will quickly become apparent. 3.3.1.1.2 Analysis of a Wing with Winglets that are Vertically Downwards Now that the control case has been solved those results can be used to compare with the experimental cases, winglets up and down. If the lift/drag ratio increases, which it should, then we have proven the fact that winglets decrease wing-tip vortices, makes an aircraft more aerodynamic which can be translated directly to fuel savings. When designing optimal winglets, every possibility has to be explored to determine the best winglet configuration, which is why a wing-tip down assembly was constructed. Figure 47, shows an isometric view of the Trefftz plane of the pressure field that is 10 meters behind the wing. Comparing Figure 45 and Figure 47, already a reduction in wing-tip vortices is apparent; this will obviously translate to a stronger lift/drag ratio for this wing. Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 56
Force Functions Coefficient of Lift (CL) Coefficient of Drag (CD) Lift/Drag ratio (CL/CD)
P a g e | 57
Figure 48, illustrates the fact that the solution for winglets down has converged due to the fact that the residuals have plateaued and have reached a high order.
P a g e | 58 Figure 49 shows the streamlines at each wing-tip. Comparing Figure 46 and Figure 47 it is apparent to see how winglets affect wing-tip vortices. Instead of the nice concentric circles that were prevalent in the simple wing, now with winglets attached a more elliptical streamline is noticeable. The streamlines are now stretched toward the tip of the winglets; since the flow from high-low pressure now has to travel a further distance, this means that vortex will now be somewhat more dissipated. This visual representation is backed by the values of the coefficients of drag, lift and moment. Now that these vortices have been weakened by the endplates, the ratio of lift/drag is considerably stronger and even the coefficient of moment is more desirable. With a coefficient of moment closer to zero, the aircraft will be more stable, giving the commercial aircraft more stability. 3.3.1.1.3 Analysis of a Wing with Winglets that are vertically Upwards Now a winglets up configuration will be compared to previous results to determine whether a winglet that is vertically up is more aerodynamic and more stable than winglets that are down. It was previously shown that winglets that are pointed down decrease drag and increase lift on a wing. So one can hypothesize that winglets up winglets up will provide the best ratio of the three; since winglets up is currently the configuration used on all modern planes.
Figure 50 shows a Trefftz plane of the pressure field 10 meters behind the wing. Like Figure 47, a reduction in vortices at the wing-tip is clear to see. However, now it is also easy to see that an area of high pressure goes up and around the winglet. This effect of the high pressure going up all the way to Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 59 the wing-tip of the winglet creates even more stability for the commercial aircraft. In the previous case of winglets down, the area of high pressure wasnt able to get around the winglet, thus not providing the stability as shown here. Since the winglet is pointing down, the high pressure generated by lift is unable to go around the winglet and push against the outside of the winglet. Before regarding any numbers or values, one can hypothesize that winglets up will yield the best lift/drag ratio and provide the most stability.
Force Functions Coefficient of Drag (CD) Coefficient of Lift (CL) Lift/Drag ratio (CL/CD)
P a g e | 60
Figure 52 proves that the solution has converged; therefore the forces in Table 3.6 can be used for comparison against the other cases. As predicted, winglets up was a clear winner, it provided the best lift to drag ratio and the most stability. The coefficient of moment is very close to zero, because of the analysis that was discussed previously. Also winglets up increase the lift and decrease drag more efficiently than both winglets down and the plain wing. Comparing Figure 49 and Figure 52 various similarities are apparent. For one, both streamlines are elliptical in nature and in both the streamlines tend to go towards the wing-tip of the winglet, instead of concentric circles that is evident from Figure 46. Figure 52, also better illustrates the area of high pressure that covers the outside of the winglet, leading to a more stable winglet. This fact is proven by the coefficient of moment which is close to 0. Due to all these factors, the curtain effect prevalent very downstream of the aircraft will be significantly reduced. In conclusion, between the alternatives of no winglets, winglets up or winglets down; the obvious winner is a winglet vertically up.
3.4
Design Alternate 3
The next key parameter in the design of a winglet is whether the camber in the airfoil will be
pointed in, towards the fuselage, or the camber will point outwards, away from the fuselage. As discussed in the literature review, a symmetrical airfoil provides no lift at a zero degree angle of attack, therefore commercial aircraft have cambered airfoils that will provide extra lift and therefore create an
P a g e | 61 area of higher pressure at the bottom of the wing. Since lift creates wing-tip vortices and drag is a function of lift, it makes sense to say that winglets destroy these vortices by creating negative lift. This negative lift is obviously going to be a function of where the camber in the airfoil is. So now a study will be conducted on various winglets to determine the placement of the camber in an airfoil of a winglet. The coefficients of moment, lift and drag will be analyzed to determine the best winglet. Now that it is known that winglets up are the best performing, all the analyses from now on will be done on winglets that are vertically up. 3.4.1.1.1 Analysis of a Simple Rectangular Wing This case will be used as the control to compare these results with those of the experimental cases, camber in/out. In all experiments a datum is needed to give the results obtained a point of reference. This rectangular wing has no change in chord length along the span.
Parameter Mach Number (M) Angle of Attack () Pressure (p) Height (h) Temperature (T) Density of Air () Kinematic Viscosity () Free Stream Velocity (U) Planform Area (Aref) Mean Aerodynamic Chord (Lref) Wing Span 0.3 8.0
Value
81.22 KPa 1830 m (6000 ft) 276.26 K 1.2798 kg/m3 0 m2/s 99.96 m/s 181.38 m2 5.34 m 34.2 m
Center of Rotation (Center of Pressure) (2.23, -0.23, 0) Lift Direction (Vector Value) (0, 1, 0)
P a g e | 62 Drag Direction (Vector Value) Pitch Axis (Vector Value) # of Nodes on Cluster (1, 0, 0) (0, 0, 1) 10
Table 3.7 gives the values that were input into OpenFOAM to solve for the coefficients of lift, drag and moment. The conditions here are the same as in the previous cases except that now the wing is given an 8 angle of attack. The airfoil used for the wing and winglet is a NACA 2412, and using a higher angle of attack will generate more lift thus producing more induced drag. So if more wing-tip vortices are present it will be clearer when looking at the solution which winglet is more effective and is dissipating vortices at the wing-tips.
Table 3.8 gives the dimensions that were used to construct the domain box for the next three cases. The same domain box was used because the wing was used in all three cases, only the winglet varied for each case.
P a g e | 63
Figure 53 is a Trefftz plane of the pressure field 10 meters behind the wing. Even though the wing here varies from the winglets up/down study, Figure 45, there are various similarities in the solution. To begin with, when there is no winglet attached at the end of the wing, wing-tip vortices are very much present and visible and is contributing to the drag. Also, when applying streamlines at the wing-tip, the vortices can be seen as round concentric circles, there is nothing to dissipate these vortices; therefore drag will be high, especially at a high angle of attack.
Force Functions Coefficient of Drag (CD) Coefficient of Lift (CL) Lift/Drag ratio (CL/CD)
Table 3.9 gives the coefficients of lift, drag and moment. These values will be used to compare to the experimental cases of winglets camber in/out. Figure 54 shows a plot of the residuals of Uy and Uz vs. time, the fact that the solution has converged gives validity to the results obtained.
P a g e | 64
The best way to visualize a winglet with the camber pointing in is to imagine that the ends of a cambered wing are simply lifted up vertically to form a winglet. Camber out is the opposite of this, from the wing-tip to the top of the winglet, the airfoil of the wing is reversed. The transition for both of these winglets is elliptically blended. Figure 55 is magnified and is a top view of the winglet to better visualize this. As can be seen, the winglet is basically a continuation of the wing, just turned up vertically.
P a g e | 65
P a g e | 66
Force Functions Coefficient of Drag (CD) Coefficient of Lift (CL) Lift/Drag ratio (CL/CD)
Figure 56 shows the Trefftz plane of the pressure field 10 meters behind the wing. As shown in the figure the wing-tip vortices have been significantly reduced. Comparing Table 3.9 and
Table 3.10 it shows that indeed this observation is true because there is a decrease in drag. The increase in lift can be attributed to the positive traction component of the winglet, the elliptical translation of this winglet is what provides this effect. Surrounding the winglet, an area of high pressure is clearly seen. This area of high pressure extends all the way to the tip of the winglet and provides stability to the wing; this is exactly what is needed for a commercial airplane. One can tell that the coefficient of drag has decreased in this case study just by looking at the streamlines in Figure 56. This figure shows how the streamlines have transformed and have become more elliptical in nature. This elliptical shape extending towards the tip of winglet is what dissipates the energy from the wing-tip Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 67 vortex, thus leading to a decrease in drag. As illustrated in Figure 53, without any end-plates flow is free to travel from high to low pressure and creating tremendous drag. With end plates flow is forced to travel up and around the winglet, thus weakening the flow considerably and lowering drag. 3.4.1.1.3 Analysis of a Winglet with Camber Pointing Outwards
Figure 58 helps visualize what camber out what really means. As stated before it is the opposite of camber in and because the cambered part of the airfoil points away from the fuselage.
P a g e | 68
Figure 59: Trefftz Plane of Winglets with Camber Out
Force Functions Coefficient of Drag (CD) Coefficient of Lift (CL) Lift/Drag ratio (CL/CD)
Evaluating the values for the force functions, it is clear that a winglet with a camber in the airfoil pointing outwards does not provide optimal results. Comparing Table 3.10 and
Table 3.11 shows that the winglets with the camber pointing towards the fuselage reduced more drag and provided extra lift. Also the coefficient of moment was closer to zero with camber in winglets than with winglets cambered out. This last part can be explained by referring to Figure 59, in it is clear that the area outside the winglet does not have the high pressure as shown in the previous case. This fact leads to the wing having less stability. Even though this case provided a better lift/drag ratio than the control case, the best performing winglet without a doubt is a winglet with camber pointing inwards, toward the fuselage. Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 69
3.5
Proposed Design
After extensive CFD analysis to determine the best configuration of 3 key parameters it is safe to
say that the best winglet to optimize is the one has that has an elliptically blended transition, points completely upwards and the camber in the airfoil points inwards, towards the fuselage. All possible alternatives for the three parameters have been proposed and tested, and this proposed configuration will be the best performing winglet.
Chapter 4
Optimization
4.1
Design Variables
The first step in optimization is to determine the design variables. The design variable is a
parameter that the engineer or designer is able to modify that changes a system. These design variables need to have a range.
4.2
Objectives
An objective is a numerical value that is to be maximized or minimized. For the optimization of
winglets, two objectives are deemed essential. These are that the winglets maximize lift and minimize drag. When determining objectives for a problem, it can be multidisciplinary. For example, a designer or engineer may want to reduce weight of a fuselage, increase its structural integrity while keeping the design under a budget.
4.3
Optimization Algorithm
Once the objective functions, parameters and ranges for these parameters are chosen,
optimization of the system can begin. The ideal setup for optimization would be to tether a shape generator to an optimization algorithm. The logic behind this is that the shape generator performs CFD analysis on an initial geometry. The values of lift, drag and moment would be input to the optimizer, the Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 70 optimizer would then command the shape generator how to modify the geometry, to better suit the objective functions. This process would repeat in a loop until the optimum winglet whose criterion meets those of the objective functions. However, the TESLA parallel-computing lab at FIU has a Linux server, and there is no shape generator available that runs in a LINUX based environment. So a more robust optimization will be performed. This involves creating 100 different winglets in SolidWorks and performing CFD analysis on them. These 100 cases will be created by using a random number generator to pick values for each of the five design variables; this is done to avoid bias when picking the values. Each winglet will be completely different from the one before, since the parameters that define it will be completely random. Once these 100 winglets have reached convergence on OpenFOAM and their respective coefficient of lift, moment and drag are obtained; these values will be input to the optimizer. Based on these values that have been inputted, a population of winglets will be created and a non-gradient based algorithm will determine the most suitable winglet.
4.4
parameterize the winglet configuration. A total of 6 variables were defined to fully characterize the elliptic profile of the winglets, their names and meanings can be found in
Table 4.1: Variables that define elliptical winglets
Variables a (addition to span) [m] b (height) [m] n (curvature ratio, lame equation exponent) Cw (winglet chord length) [m] (winglet tilt back angle) []
P a g e | 71
Figure 61 shows the side view of the 4 extreme of the winglet configurations we chose in order to optimize the best elliptical winglet configuration that outputs the higher CL/CD ratio for the given rectangular wing. The coordinate reference system was chosen to match the one from the design software SolidWorks. Some of the limit of these parameters will vary with respect to the parameters of table 1. Therefore their relations are expressed in the next figure considering an arbitrary elliptical configuration.
Tilt back angle of the winglet trailing edge curve (), tilt back angle of the winglet leading edge curve (), winglet chord length (Cw) and winglet high or ellipse vertical length (b). From the above figure we can define all the variables we need to design a winglet in SolidWorks by the following trigonometric relations:
P a g e | 72
Using the above relations we created an excel sheet that outputs random elliptical profiles. These profiles are then converted into a leading curve and a trailing curve and loaded to the SolidWorks model to create the winglet. The initial point for the leading curve is the initial point of the leading edge and for the trailing curve this point coincides with the initial point of the trailing edge. The ellipse profile is being generated randomly between the limits we chose for our optimization parameters which are presented in the table 1.
For Figure 63 and Figure 64, the blue and green curves represent the leading edge of two different winglet configurations. The red and yellow curves are the trailing edge of the respective winglet configuration. This definition makes the blue and red curve one elliptical winglet profile and the Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 73 green and yellow curve another winglet profile. Figure 63 is the front view of these profiles and Figure 64 is the side view of the same winglet profiles.
6 5 4 b 3 2 1 0 0 1 c1L 2 c1T 3 c 4 c2L 5 c2T 6
From Figure 64 the changes between the tilt back angle (for the leading edge) and (for the trailing edge) that occurs for the different elliptical profiles are possible to see.
Table 4.2: Range of Optimization Parameters
Parameter a (ellipse horizontal length) b (ellipse vertical length) n (ellipse equation exponent) Cw (winglet chord length) (tilt back angle of winglet leading curve)
The parameters from Table 4.2 will define the parameters represented in Figure 62 depending on the wing thickness and chord length ratio. This will assure to optimize a customized elliptic winglet for a specific wing airfoil. Considering the range of the above parameters a total of 100 elliptical profiles were created to be optimized. The optimal shape will be the one that gives the higher ratio between the lift coefficient and the drag coefficient (CL/CD). The result of this optimization will be tested in a wind tunnel with a scaled model to validate computational work.
P a g e | 74
4.5
optimizer was used to create a Pareto front for the optimal results. This optimizer was developed by Marcelo Colao .This optimizer only outputs results for a combination of two parameters for example, Maximum Cl and Minimum Cd. Therefore we created 6 graphs in order to better analyze these results. From the Figure 65 to the Figure 70 the results for all the possible combinations of our project target can be seen. Also to determine which of these results will be the best for our target wing, NACA2412, we divided each of them by the coefficients of lift, drag, moment, and lift/drag of the naked wing shown on table 1. These results help us to determine the winglet configurations that accomplished these parameters which are shown on Table 4.4. Then we place these points (A to D) also in the Figure 65 through Figure 70 to see their position with respect to the Pareto front. However in order to determine the best winglet configuration is necessary to consider the simultaneous effect of all the coefficients and not chose a configuration base on only the limit value of one coefficient. Therefore configuration 1 from the same table was determined. Table 4.3 contains the coefficient values for the NACA2412 without any winglets.
Table 4.4: Corresponding winglets configurations for maximum Cl and Cl/Cd and minimum Cd and Cm
Objective Result
Name
Optimized winglets variables 45.0298 45.0298 a 0.38709 0.38709 b 5.38532 5.38532 cw 1.63492 1.63349 n 1.52262 1.52262 Cd 0.05833 0.05833
Change with respect to wing Cd 6.45% Cl 16.20% Cm 15.91% 15.91% Cl/Cd 8.67% 8.67%
2 A 1
16.20%
0.7044
-0.077
6.45%
P a g e | 75 Max Cl -0.11988 -0.11988 4.04182 4.04182 5.38532 5.38532 2.56522 2.56522 8.16336 8.16336 0.08643 0.08643 1.06478 1.06478 28.5575 28.5575 12.3127 12.3127 57.72% 75.65% 80.47% 80.47% 70.71% 19.4% 7.04% 1 B 4 11.33% 12.3% 14.03% -2.37% 11.33%
Min Cm 0.38709 2.40916 1.33789 1.52262 0.06158 0.65668 44.3416 10.7976 -0.0711 C 4 8.33% 32.4% 64.27%
Max Cl/Cd 3.68173 2.94743 3.53966 4.87428 0.07867 0.99582 45.0298 D 3 12.6119 -0.1134
3.389567
4.646773
1.932981
0.064629
0.802758
44.60927
From the above table we can see that for configurations A and B we obtained duplicated winglets configurations from different optimization objectives with the same minimum Cd coefficient. Configurations C and D are the best fit options for minimum Cm and maximum aerodynamic efficiency. Configuration 1 is the optimal winglet configuration resulting from analyzing the combined effect of all the four coefficients we target in this project. The process of choosing this configuration is completely up to the authors decision and analysis of the optimization results. This process will be described below with the help of 3D graphs represented from Figure 71 to Figure 86.
12.42096
-0.07931
1.52262
75.65%
P a g e | 76
4.6
1.10 1.00 0.90 Cl 0.80 0.70 0.60 0.50 0.05 0.06 0.06 A 0.07 B Cd C 0.07 D 0.08 0.08 0.09 1
Raw data
Wing
Figure 65: Discontinuous Pareto Front for Objective 1, minimum Cd and maximum Cl
Figure 65 shows the results for maximum Cl and minimum Cd, objective 1. Where A represents the winglet configuration that correspond to Minimum Cd, B is for maximum Cl, C is for minimum Cm and D is for maximum Cl/Cd. As we can see from Figure 65 through Figure 66 the Pareto front for all the objectives is discontinued. The values given for the naked wing are shown in these graphs to see the improvement of the winglet configurations.
P a g e | 77
-0.05 -0.06 -0.07 -0.08 Cm -0.09 -0.10 -0.11 -0.12 -0.13 -0.14 0.05 0.06 0.06 A 0.07 B Cd C 0.07 D 0.08 0.08 0.09 1
Raw data
Wing
13.00 12.50 12.00 Cl/Cd 11.50 11.00 10.50 0.05 0.06 0.06 0.07 Cd A B C D Pareto front Objective 3 Raw data Wing 1 0.07 0.08 0.08 0.09
Figure 67: Discontinuous Pareto Front for Objective 3, maximum Cl/Cd minimum Cd
P a g e | 78
-0.06 -0.07 -0.08 Cm -0.09 -0.10 -0.11 -0.12 -0.13 0.56 0.66 A 0.76 B Cl C 0.86 D 0.96 Raw data 1.06 Wing 1
13.00
12.50
12.00 Cl/Cd 11.50 11.00 10.50 0.56 A B C 0.66 D 0.76 0.86 0.96 Raw data 1.06 Wing 1.16 1
Figure 69: Discontinuous Pareto Front for Objective 5. Maximum Cl/Cd maximum Cl
P a g e | 79
13.00 12.50 12.00 Cl/Cd 1 11.50 11.00 10.50 10.00 -0.13 A B -0.12 C -0.11 D -0.10 -0.09 -0.08 -0.07 -0.06 Wing
Raw data
Figure 70: Discontinuous Pareto Front for Objective 6, maximum Cl/Cd minimum Cm
P a g e | 80
High CL High CD
Low CL Low CD
P a g e | 81
Low CD Low Cm
High CD High Cm
Figure 73: Cm vs Cd
Low CL Low Cm
High CL High Cm
Figure 74: Cm vs Cl
P a g e | 82
Low CL Low Cm
Figure 76: Cm vs. Cl
High CL High Cm
P a g e | 83
P a g e | 84
P a g e | 85
High CD High CL
Low CL Low CD
Low CD Low CM
High CD High CM
P a g e | 87
P a g e | 88
4.7
Parameter Mach Number (M) Angle of Attack () Pressure (p) Height (h) Temperature (T) Density of Air () Kinematic Viscosity () Free Stream Velocity (U) Planform Area (Aref) Mean Aerodynamic Chord (Lref) Wing Span Center of Rotation (Center of Pressure) Lift Direction (Vector Value) Drag Direction (Vector Value) Pitch Axis (Vector Value) # of Nodes on Cluster
Value 0.3 8.0 81.22 KPa 1830 m (6000 ft) 276.26 K 1.2798 kg/m3 0 m2/s 99.96 m/s 95.85 m2 5.367 m 17.1 m (2.285, -0.1377, -6.86) (0, 1, 0) (1, 0, 0) (0, 0, 1) 10
Force Functions Coefficient of Lift (CL) Coefficient of Drag (CD) Coefficient of Moment (CM) Lift/Drag ratio (CL/CD)
P a g e | 90
Figure 88: Front View of Trefftz Plane for Simple NACA 2412 Wing
P a g e | 91
Figure 91: Plot of Residuals vs. Time for Simple NACA 2412 Wing
Force Functions Coefficient of Lift (CL) Coefficient of Drag (CD) Coefficient of Moment (CM) Lift/Drag ratio (CL/CD)
P a g e | 92
P a g e | 93
P a g e | 94
P a g e | 95
Force Functions Coefficient of Lift (CL) Coefficient of Drag (CD) Coefficient of Moment (CM) Lift/Drag ratio (CL/CD)
P a g e | 96
P a g e | 97
P a g e | 98
P a g e | 99
P a g e | 100
Chapter 5
Aerodynamic Analysis
Parameter Mach Number (M) Angle of Attack () Pressure (p) Height (h) Temperature (T) Density of Air () Kinematic Viscosity () Free Stream Velocity (U) Mean Aerodynamic Chord (Lref) Planform Area (Aref) Wing Span Center of Rotation (Center of Pressure) Lift Direction (Vector Value) Drag Direction (Vector Value) Pitch Axis (Vector Value) # of Nodes on Cluster
Value 0.3 8.0 81.22 KPa 1830 m (6000 ft) 276.26 K 1.2798 kg/m3 0 m2/s 99.96 m/s 5.367 m 79.68 m2 17.1 m (5.97, -0.34, 4.62) (0, 1, 0) (1, 0, 0) (0, 0, 1) 10
5.1
Force Functions Coefficient of Lift (CL) Coefficient of Drag (CD) Coefficient of Moment (CM) Lift/Drag ratio (CL/CD)
P a g e | 101
Figure 106: Top View of Domain of Simple, Half 757 Wing with a Symmetry Plane
Figure 107: Front View of Trefftz Plane for Simple 757 Wing
P a g e | 102
P a g e | 103
Figure 110: Plot of Residuals vs. Time for Simple 757 Wing
5.2
Force Functions Coefficient of Lift (CL) Coefficient of Drag (CD) Coefficient of Moment (CM) Lift/Drag ratio (CL/CD)
P a g e | 104
P a g e | 105
Figure 114: Front View of Trefftz Plane of Original Boeing 757 Winglet
P a g e | 106
Figure 115: Side View of Pressure Field for Original Boeing 757 Winglets
P a g e | 107
Figure 117: Plot of Residuals vs. Time for Original Boeing 757 Winglets
P a g e | 108
5.3
Force Functions Coefficient of Lift (CL) Coefficient of Drag (CD) Coefficient of Moment (CM) Lift/Drag ratio (CL/CD)
P a g e | 109
P a g e | 110
Figure 121: Front View of Trefftz Plane for Optimal Boeing 757 Winglets
Figure 122: Side View of Pressure Field for Optimal Boeing 757 Winglets
P a g e | 111
Figure 124: Plot of Residuals vs. Time for Optimal 757 Winglets
P a g e | 112
Table 5.13: Comparison of aerodynamic efficiency of 757 with and without winglets
Simple 757 Wing Coefficient of Lift Coefficient of Drag Coefficient of Moment CL/CD Desired Improvement of CL/CD Actual Improvement of CL/CD 0.496619 0.095009 0.0488408 5.227 8% 5.2%
Chapter 6
6.1
Testing
With the rapid modernization of computers and their increased role in industry, computers are
now playing new roles in the field of engineering and the sciences. Prior to CFD analysis and computer clusters, wind tunnels were the norm in the fields of aerodynamic design and testing. Throughout the years, CFD programs have been evolving and the size and power of computers have been growing; as a result, wind tunnel testing has now played a less crucial role in design. However, the scientific method is based on gathering experimental, empirical evidence through observation and experimentation to test a hypothesis. In order to prove the validity of our computational analysis, experiments have to be conducted in a wind tunnel. The empirical values of Cd, CL, CM and ultimately CL/CD will be compared to their analytical counterparts attained through OpenFOAM simulation. To test prototypes on a wind tunnel, the cross sectional area of the test section of the wind tunnel is a crucial value to know. The size of the prototype has to adhere to certain restrictions so as to avoid blockage of the wind tunnel. At least 7 inches of clearance between the wall of the wind tunnel and each side of the wing have to be given. This is also done to allow the vortices at the wing-tip to properly develop. 7 inches is a good general rule of thumb to remember, if this rule is not adhered to,
P a g e | 113 flow will not properly develop and experimental results will not reflect those of CFD simulations. Figure 125 illustrates this rule of thumb well.
Embry-Riddle Aeronautical University currently has two excellent wind tunnels in which testing can be performed. One is a wind tunnel with a 40x30 test cross section, the second is a smoke tunnel with a 24x18 test cross section. Smoke tunnels have the added advantage of flow visualization, this way flow separation point and boundary layer can be seen with ease. Acknowledgements have to be given to Mr. Snorri Gudmundsson and Mr. Michael Scheppa for giving us full access to all their testing facilities and for their help in guidance in testing.
P a g e | 114
To verify the computational work performed throughout, several configurations of winglets will be tested. To corroborate our initial testing on the effect of the camber on the airfoil in the winglet; winglets with airfoils that are symmetrical, cambered in, out will be tested on a NACA 2412 wing. To take advantage of both the wind and smoke tunnels, two sets of NACA 2412 wings will be manufactured, one for each tunnel. Calculating for the least amount of blockage, the wing for the wind tunnel will have a span of 18 while the wing for the smoke tunnel will be 12 spanwise. These dimensions were calculated as desirable for wind to develop over the wingtips. The chord length of both wings will remain constant, so as to be able to retrofit all winglets on both wings and test them in both tunnels. The only factor between both wings that varied was the span. Maintaining the same chord length between both wings has the advantage of significantly saving money, creating separate winglets for each wing would be very costly. Since the objective is to find CL,CD,Cm , the span of the wing will not skew results since these are dimensionless parameters. To retrofit the wing to the winglets, two holes will be drilled in the wing and winglet; the holes will be 1/8 diameter to allow a slender steel pin to connect both.
Once the reasoning for the preliminary analysis is complete, the next logical step is to test all the optimal winglets. Winglet configurations #s 1,2 and 5, chosen as optimal from the Pareto front graphs, Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
P a g e | 115 will be tested for its aerodynamic efficiency on the smoke and wind tunnels using both NACA 2412 wings. To test the optimal Boeing 757 winglet, the 757 wing will have to be constructed. This wing will only be tested in the wind tunnel. Flow visualizations on the NACA 2412 winglets will provide sufficient data as to flow separation point and boundary layer, such that more is not necessary. Two winglets will be tested on this wing, the optimal Boeing 757 winglet and the original 757 winglet. The best of these will be found experimentally, and if these results coincide with those of OpenFOAM, more validity will be given to CFD analysis as a reliable tool for aerodynamic design and analysis.
6.2
Manufacturing
These several configurations of winglets will be manufactured using a Z-510 3D Printer, rapid
prototype machine. The 3D printer was chosen as the best option for constructing the wing + winglets, it is one of the most efficient rapid protyping machine in industry. It is capable of creating physical models from CAD files in hours instead of days. Parts however are very fragile and epoxy resin has to be applied to insure complete infiltration. As illustrated in Figure 129, parts are extremely fragile and great care has to be taken when removing them from the bin. The procedure for the manufacturing of these winglets was as follows: 1. Excavate and remove parts from bin of 3D printer with extreme care, parts are very fragile, and break easily. 2. De-powder excess dust and powder with a small vacuum cleaner. 3. To strengthen parts apply a marine grade epoxy, before applying epoxy, heat parts in a 200 F oven for 30 minutes. 4. Apply epoxy resin until the part is completely infiltrated with the epoxy. 5. To speed up curing process of epoxy, place parts in a 100 oven for 45 minutes and let the parts completely de-gas. 6. Sand down parts to remove any imperfections, until it is perfectly smooth. This part is important because if part is not smooth interferences will exist with the wind and results will be skewed. 7. Drill 1/8 holes into winglets and wing to allow space for steel pins to be inserted.
P a g e | 116
P a g e | 117
P a g e | 118
P a g e | 119
Chapter 7
Environmental Impact
7.1
economical sense. But will it be also beneficial to the environment? To address this question we look into several articles to create a global and or local impact description of the issue in question. When keeping track of the aviation history we found that the three more important aspects that define the environmental impact of the aviation industry are the noise pollution, the local air quality and the climate changes5. If we look into the future clearly the last one is the most important of them. According to the Royal Commission on Environmental Pollution6 There are other points to consider when analyzing the effect of aircraft in flight into the environment7, for example the stratospheric ozone reduction that leads to an increment of the UV radiation surface, or the regional or global pollution associated to chemical changes in the troposphere that can reach several kilometers downwind of airports, and also there is the local pollution based on the noise level and the decrement of the air quality cause by COx emissions from the aircrafts.
Now entering into what winglets do or change in aircrafts according to the Aircraft Research Association in Bedford, UK we can clearly see that they affect the noise pollution factor in a positive way. Their blended or elliptical transition from the wing tip helps reduce the stress concentration points and their shape helps to reduce vortices formation or induced drag making the engines work less while the takeoff or landing procedures8,9.
With respect to the climate or global pollution the winglets did not act directly, but indirectly they help with the reduction of NOx and CO2 emissions while reducing the fuel engines burn during takeoff and landing up to 6% for some aircrafts and about 3.2% for the 757-2002. During flight airplanes engines have several types of emissions such as CO2, NOx, water vapor, hydrocarbons and sulfate or sulfur oxides in form of particles. All of them can affect the chemical balance and composition of the atmosphere in a long term or short term range. The way winglets influence on this factor is indirectly and minimal because they only reduce the engines fuel usage during takeoff and landing procedures. As
P a g e | 120 a matter of fact during flight winglets increase the friction drag because they constitute an addition of surface area into the airplane structure10.
When the airplane is flying the engines emit CO2 as result of the kerosene combustion and it mixes very well into the atmosphere. But the NOx emissions product of the elevated temperature the engines work are quickly reacting leading to concentration changes of ozone and methane. However this effect only occurs in the lower stratosphere. In the troposphere ozone is created by the NOx emissions. However since ozone has a short life period its concentration increments or decrements are limited by to a short distribution horizontal and vertically in the atmosphere. On the other hand methane life is long enough to allow the reduction of it to be spread throughout the entire atmosphere. This change will contribute to the greenhouse effect, because methane is one of the gases that permit through the short wave solar radiation and absorb and emit again the long wave thermal radiation crating the heating of the region near the tropopause. This is also clearly shown on Figure 136.
Figure 136: The structure of the atmosphere below 50 km [6] Summarizing the overall impact of winglets into the environment we can say that they majorly influence indirectly into the noise pollution, the local climate change, and the global pollution by increasing the engines performance. This way engines burn less fuel and reduce the greenhouse gases emission. Since engines have to work less they will produce less noise.
P a g e | 121
Chapter 8
Conclusion
Large commercial transport planes are not likely to be critically affected by trailing vortices from a preceding aircraft, however, due respect has to be given to these type of flow structures. Wing tip vortices have been recorded to have lasted up to 3 minutes after the passing of a large aircraft, and having moved a total of 200 ft. vertically while producing substantial downwind up to 300 m/s downwind. Aerodynamic efficiency, L/D Ratio, leads to a series of factor which impact the economics of flying with the extent of fuel consumption and fatigue on the aircraft, noise and many more. These are all motives why rotational flow patterns are so highly regarded and studied. Thanks to winglets, aircrafts will be able to more efficiently consume fuel, extend their range capabilities, reduce takeoff and landing thrust settings, and cut down on noise and emissions.
P a g e | 122
Chapter 9 9.1
Appendix
Specifications Boeing 757-200 Versions B757-200 B757-200 Freighter B757-200M B757-200PF B757-200SF B757-200X VC-32A initial production passenger aircraft developed by Pemco Aeroplex as conversion to existing 757 aircraft combi; mixed cargo/passenger version; only one delivered to Royal Nepal Airlines package freighter; developed for United Parcel Service modified 200 coverted by Boeing to Special Freighter extended range version; more than 1.000 km increase in range military version; 4 built for U.S. Air Force
Engines
Type 2 Pratt & Whitney PW2037 2 Pratt & Whitney PW2040 2 Rolls Royce RB211-535E4 2 Rolls Royce RB211-535E4-B Fuel Capacity
Thrust 36,600 lb st (162,8 kN) 40,100 lb st (178,4 kN) 40,200 lb st (178,8 kN) 43,500 lb st (193,5 kN) 42.684 liters (11,276 US gallons)
P a g e | 123
Table 9.3: Workload of the Boeing 757-200 aircraft [11]
2 5-7 9 2 3 4 3
provision for an observer from 178 in 2-class to 239 passengers in all tourist 1 front starboardside; 1 rear in 239 passenger version (midships) 1 front portside; 3 rear 1 front portside; 2 rear of mid-ships (239 passenger version)
Dimensions; external wingspan 38,05 mtr wing chord; at root 8,20 mtr wing chord; at tip 1,73 mtr wing aspect ratio 7,8 length; overall 47,33 mtr length; fuselage 46,97 mtr tailplane span 15,22 mtr tail height 13,49 mtr min 13,74 mtr max wheel track 7,32 mtr wheelbase 18,29 mtr
Table 9.5: Operational external weights of the Boeing 757-200 aircraft [11]
Weight and loadings operating weight empty 57.840 - 57.975 kg operating weight empty (freighter) 50.475 - 50.605 kg freighter revenue load 32.755 kg freighter payload 757-200 SF 27.215 kg max. take-off weight (PW2037 & RB211-535E4) 99.790 kg max. take-off weight (PW2040 & RB211-535E4-B) 115.665 kg max. landing weight (PW2037 & RB211-535E4) 89.815 kg max. landing weight (PW2040 & RB211-535E4-B) 95.255 kg max. ramp weight (PW2037 & RB211-535E4) 100.245 kg max. ramp weight (PW2040 & RB211-535E4-B) 116.120 kg
P a g e | 124
Table 9.6: Flight performance parameters of the Boeing 757-200 [11]
Performance max. operating Mach cruising speed approach speed (PW2037 & RB211-535E4) approach speed (PW2040 & RB211-535E4-B) cruising height: PW2037 / PW2040 cruising height: RB211-535E4 / RB211-535E4-B take-off field length: PW2037 / PW2040 take-off field length: RB211-535E4 / RB211-535E4-B landing field length: PW2037 / PW2040 landing field length: RB211-535E4 / RB211-535E4-B range: PW2037 / PW2040 range: RB211-535E4 / RB211-535E4-B
0.86 M 0.80 132 knots (245 km/h) 137 knots (254 km/h) 11.675 mtr (38,300 ft) / 11.795 mtr (38,700 ft) 10.790 mtr (35,400 ft) / 10.880 mtr (35,700 ft) 1.814 mtr (5,950 ft) / 1.677 mtr (5,500 ft) 2.378 mtr (7,800 ft) / 2.104 mtr (6,900 ft) 1.463 mtr (4,800 ft) / 1.418 mtr (4,650 ft) 1.555 mtr (5,100 ft) / 1.494 mtr (4,900 ft) 4.769 km (2,570 Nm) / 4.398 km (2,376 Nm) 7.278 km (3,930 Nm) / 6.843 km (3,695 Nm)
P a g e | 125
9.2
figure is a 3-D picture of the model we used in solidworks to optimize winglets for.
Figure 137: Boeing 757 aircraft SolidWorks model. These are our target aircraft wings
P a g e | 126
P a g e | 127
P a g e | 128
HA
Figure 140: Technical drawings of the wing for a 757 Boeing aircraft.
LF
P a g e | 129
Figure 141: Technical drawings for a rectangular camber wing NACA 2412 with the same average chord length as the wings of the 757 Boeing aircraft.
P a g e | 130
Figure 142: Technical drawing of a random elliptic blended winglet configuration. The optimization parameters a, b, n, cw and are shown also in this figure.
P a g e | 131
9.3
Winglet # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
Cd
0.068345 0.062514 0.065624 0.070218 0.067351 0.060672 0.065482 0.069146 0.063772 0.062145 0.063235 0.070695 0.061459 0.062271 0.060168 0.059584 0.068826 0.066075 0.062924 0.062624 0.066892 0.064379 0.064242 0.066089 0.065827 0.059417 0.06354 0.066317 0.066876 0.064514 0.065261 0.071363 0.066056 0.065468 0.068243
Cl
0.739014 0.770204 0.804262 0.764275 0.75718 0.730628 0.812137 0.781814 0.767287 0.766581 0.667225 0.808459 0.75213 0.776261 0.733081 0.700233 0.8302 0.799084 0.70472 0.726496 0.810707 0.757304 0.77116 0.804213 0.795359 0.706493 0.744834 0.787868 0.768412 0.723628 0.774121 0.847006 0.711902 0.766487 0.790893
Cm
-0.08103 -0.07896 -0.08222 -0.08376 -0.08103 -0.0815 -0.08276 -0.08404 -0.08277 -0.08438 -0.07022 -0.08918 -0.08357 -0.08791 -0.07816 -0.07525 -0.08882 -0.09252 -0.07618 -0.08057 -0.09482 -0.08657 -0.08835 -0.09182 -0.09081 -0.0777 -0.08159 -0.08838 -0.08131 -0.08025 -0.08562 -0.09821 -0.07714 -0.08501 -0.08652
Cl/Cd
10.813 12.32 12.256 10.884 11.242 12.042 12.402 11.307 12.032 12.335 10.551 11.436 12.238 12.466 12.184 11.752 12.062 12.094 11.2 11.601 12.12 11.763 12.004 12.169 12.083 11.89 11.722 11.88 11.49 11.217 11.862 11.869 10.777 11.708 11.589
20.256 41.98 37.917 11.842 25.344 10.527 40.327 5.397 16.151 31.91 41 29.377 39.056 21.496 41.067 29.899 32.157 23.951 27.83 18.925 14.872 6.831 25.847 30.477 30.986 43.125 29.882 29.312 27.907 26.882 41.846 1.06 12.515 29.542 35.837
a
2.072 2.815 3.515 0.931 2.111 1.7556 3.6661 2.2063 2.4574 2.418 1.2233 3.8778 1.943 2.7937 1.344 0.6588 3.2135 3.1134 1.3662 1.208 3.2984 1.7084 2.03 2.833 3.98 0.743 1.9812 3.0467 2.904 2.7982 1.939 3.7765 1.596 2.1634 3.19
b
5.236 3.914 5.211 2.253 3.46 2.757 4.094 2.887 4.794 3.93 2.366 2.227 3.764 4.496 5.155 4.824 5.239 3.375 2.893 4.912 3.541 4.574 4.626 5.095 2.925 3.822 2.743 2.506 5.175 1.828 4.847 5.12 4.755 4.634 3.939
cw
2.903 1.587 2.02 1.256 1.981 3.046 1.888 3.307 2.554 1.049 1.16 3.574 1.226 0.719 1.54 1.265 3.284 0.911 3.069 3.561 1.291 1.16 2.283 1.153 0.705 3.064 3.273 2.751 3.569 3.164 1.155 3.391 3.408 0.647 1.39
n
16.037 1.615 2.763 3.072 2.336 2.137 2.667 2.232 4.123 2.105 2 2.229 3.089 1.88 1.928 2.577 4.922 4.938 3.387 6.806 5.186 5.215 15.844 7.784 1.544 4.387 3.042 3.161 2.438 2.083 16.207 11.341 7.573 5.046 4.941
P a g e | 132 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
0.063118 0.063322 0.067203 0.063122 0.060796 0.062762 0.066072 0.064845 0.064222 0.067417 0.068852 0.066373 0.065685 0.058473 0.063025 0.064263 0.063056 0.062625 0.06254 0.067656 0.064607 0.065082 0.066747 0.06535 0.066592 0.064056 0.060086 0.067359 0.060754 0.067391 0.066922 0.067354 0.068173 0.065146 0.066688 0.063533 0.064287 0.06717 0.062079 0.066765 0.739882 0.726681 0.798933 0.748223 0.729888 0.750355 0.791038 0.788515 0.767301 0.829948 0.839568 0.781072 0.78912 0.706604 0.763955 0.773836 0.765545 0.751446 0.741703 0.845959 0.780937 0.790231 0.818742 0.790547 0.816557 0.771703 0.727413 0.812104 0.722218 0.823019 0.82277 0.823617 0.835251 0.779695 0.814796 0.768312 0.772613 0.822062 0.731916 0.804322 -0.08225 -0.08138 -0.09319 -0.07863 -0.08134 -0.08359 -0.08906 -0.09081 -0.08861 -0.09878 -0.09787 -0.08644 -0.09349 -0.07876 -0.08544 -0.08777 -0.08766 -0.08567 -0.08328 -0.09499 -0.0901 -0.09227 -0.09355 -0.09246 -0.09471 -0.08791 -0.08126 -0.09393 -0.08164 -0.09566 -0.09703 -0.09503 -0.09659 -0.09019 -0.09252 -0.08736 -0.08901 -0.0941 -0.08237 -0.09186 11.722 11.476 11.888 11.854 12.006 11.956 11.972 12.16 11.948 12.311 12.194 11.768 12.014 12.084 12.121 12.042 12.141 11.999 11.86 12.504 12.087 12.142 12.266 12.097 12.262 12.047 12.106 12.056 11.888 12.213 12.294 12.228 12.252 11.968 12.218 12.093 12.018 12.239 11.79 12.047 6.538 25.252 5.741 33.559 23.249 14.43 23.023 11.311 4.464 9.916 33.055 29.007 1.464 19.077 30.319 25.394 24.596 13.927 39.294 34.655 39.025 5.752 32.439 1.492 35.163 18.218 30.974 9.178 41.982 26.693 10.565 29.265 35.518 19.255 34.239 42.123 9.88 35.301 38.466 10.416 1.695 2.3288 3.752 1.965 1.1835 1.4421 2.2761 3.0116 2.472 3.813 4.0018 3.156 3.5236 0.391 2.181 2.081 2.594 1.298 2.025 3.9618 2.471 2.683 3.2601 2.3175 3.8322 2.353 0.885 2.792 1.4058 3.619 3.643 3.166 3.65 2.1604 3.483 2.136 2.4105 3.163 1.845 2.7521 2.755 2.33 1.488 4.317 4.156 4.922 4.469 3.828 2.706 3.597 3.583 1.895 1.97 4.39 3.846 4.777 3.322 5.332 2.142 4.867 3.662 4.58 4.876 4.833 2.411 4.296 4.618 4.755 2.269 2.868 3.786 5.223 4.069 5.196 3.721 3.535 4.587 4.146 1.647 4.106 3.14 0.763 2.929 0.88 2.729 1.975 2.629 2.79 2.938 1.776 1.149 3.616 0.814 2.539 1.246 3.029 1.85 3.632 2.666 1.58 0.639 2.575 1.456 2.821 3.601 1.24 3.045 3.258 1.133 1.775 2.01 2.213 1.863 1.248 2.228 0.776 1.297 3.038 1.036 3.678 4.211 2.507 3.912 1.696 2.498 1.976 5.757 1.748 2.391 3.439 7.023 2.265 1.654 3.375 2.616 5.556 1.925 6.468 3.495 3.259 7.535 2.78 4.249 10.41 3.079 2.371 9.57 4.56 6.789 6.247 2.862 12.226 8.408 8.303 3.505 11.434 1.967 11.429 16.279 4.329
1 LMT cw c a b n 2.576 34.751 5.34 3.4672 1.599 8.761 tx twx x0 s 1.798 0.867 17.145 34.29 83.612 -45.963 Leading edge Trailing edge Median edge y z x y z x y z b1L a1L c1T b1T a1L c1M b1M a1M 0 0 5.34 0 0 1.7979 0 0 0 0.035 5.34 0 0.035 1.7979 0 0.035 0 0.07 5.34 0 0.07 1.7979 0 0.07 Aerodynamic Shape Design Optimization of Winglets FIU College of Engineering
x c1L 0 0 0
P a g e | 134 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1E-05 1E-05 1E-05 1E-05 1E-05 2E-05 2E-05 3E-05 4E-05 5E-05 6E-05 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1E-05 1E-05 1E-05 1E-05 2E-05 2E-05 3E-05 3E-05 4E-05 5E-05 7E-05 8E-05 0.0001 0.1051 0.1401 0.1751 0.2101 0.2452 0.2802 0.3152 0.3502 0.3852 0.4203 0.4553 0.4903 0.5253 0.5604 0.5954 0.6304 0.6654 0.7004 0.7355 0.7705 0.8055 0.8405 0.8756 0.9106 0.9456 0.9806 1.0156 1.0507 1.0857 1.1207 1.1557 1.1908 1.2258 1.2608 1.2958 1.3308 1.3659 1.4009 1.4359 1.4709 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.34 5.3399 5.3399 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1E-05 1E-05 1E-05 1E-05 2E-05 2E-05 3E-05 3E-05 4E-05 5E-05 7E-05 8E-05 0.0001 0.1051 0.1401 0.1751 0.2101 0.2452 0.2802 0.3152 0.3502 0.3852 0.4203 0.4553 0.4903 0.5253 0.5604 0.5954 0.6304 0.6654 0.7004 0.7355 0.7705 0.8055 0.8405 0.8756 0.9106 0.9456 0.9806 1.0156 1.0507 1.0857 1.1207 1.1557 1.1908 1.2258 1.2608 1.2958 1.3308 1.3659 1.4009 1.4359 1.4709 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 1.7979 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1E-05 1E-05 1E-05 1E-05 2E-05 2E-05 3E-05 3E-05 4E-05 5E-05 7E-05 8E-05 0.0001 0.1051 0.1401 0.1751 0.2101 0.2452 0.2802 0.3152 0.3502 0.3852 0.4203 0.4553 0.4903 0.5253 0.5604 0.5954 0.6304 0.6654 0.7004 0.7355 0.7705 0.8055 0.8405 0.8756 0.9106 0.9456 0.9806 1.0156 1.0507 1.0857 1.1207 1.1557 1.1908 1.2258 1.2608 1.2958 1.3308 1.3659 1.4009 1.4359 1.4709
P a g e | 135 7E-05 9E-05 0.0001 0.0001 0.0002 0.0002 0.0002 0.0003 0.0003 0.0004 0.0004 0.0005 0.0006 0.0007 0.0008 0.001 0.0011 0.0013 0.0015 0.0017 0.002 0.0023 0.0026 0.003 0.0035 0.0039 0.0045 0.0051 0.0058 0.0066 0.0074 0.0084 0.0095 0.0107 0.0121 0.0137 0.0154 0.0173 0.0195 0.0219 0.0001 0.0002 0.0002 0.0002 0.0003 0.0003 0.0004 0.0005 0.0006 0.0007 0.0008 0.0009 0.0011 0.0012 0.0015 0.0017 0.002 0.0023 0.0026 0.0031 0.0035 0.004 0.0046 0.0053 0.0061 0.0069 0.0079 0.009 0.0102 0.0115 0.0131 0.0148 0.0167 0.0188 0.0213 0.024 0.027 0.0304 0.0342 0.0384 1.506 1.541 1.576 1.611 1.646 1.6811 1.7161 1.7511 1.7861 1.8212 1.8562 1.8912 1.9262 1.9612 1.9963 2.0313 2.0663 2.1013 2.1364 2.1714 2.2064 2.2414 2.2764 2.3115 2.3465 2.3815 2.4165 2.4516 2.4866 2.5216 2.5566 2.5916 2.6267 2.6617 2.6967 2.7317 2.7668 2.8018 2.8368 2.8718 5.3399 5.3399 5.3399 5.3398 5.3398 5.3398 5.3397 5.3397 5.3396 5.3395 5.3395 5.3394 5.3392 5.3391 5.339 5.3388 5.3386 5.3384 5.3381 5.3378 5.3375 5.3371 5.3367 5.3362 5.3357 5.335 5.3343 5.3336 5.3327 5.3317 5.3306 5.3294 5.328 5.3265 5.3247 5.3228 5.3206 5.3182 5.3154 5.3124 0.0001 0.0002 0.0002 0.0002 0.0003 0.0003 0.0004 0.0005 0.0006 0.0007 0.0008 0.0009 0.0011 0.0012 0.0015 0.0017 0.002 0.0023 0.0026 0.0031 0.0035 0.004 0.0046 0.0053 0.0061 0.0069 0.0079 0.009 0.0102 0.0115 0.0131 0.0148 0.0167 0.0188 0.0213 0.024 0.027 0.0304 0.0342 0.0384 1.506 1.541 1.576 1.611 1.646 1.6811 1.7161 1.7511 1.7861 1.8212 1.8562 1.8912 1.9262 1.9612 1.9963 2.0313 2.0663 2.1013 2.1364 2.1714 2.2064 2.2414 2.2764 2.3115 2.3465 2.3815 2.4165 2.4516 2.4866 2.5216 2.5566 2.5916 2.6267 2.6617 2.6967 2.7317 2.7668 2.8018 2.8368 2.8718 1.798 1.798 1.798 1.798 1.798 1.798 1.798 1.798 1.798 1.798 1.798 1.798 1.7981 1.7981 1.7981 1.7981 1.7982 1.7982 1.7982 1.7983 1.7983 1.7984 1.7985 1.7985 1.7986 1.7987 1.7988 1.7989 1.7991 1.7992 1.7994 1.7996 1.7998 1.8 1.8003 1.8006 1.8009 1.8013 1.8017 1.8022 0.0001 0.0002 0.0002 0.0002 0.0003 0.0003 0.0004 0.0005 0.0006 0.0007 0.0008 0.0009 0.0011 0.0012 0.0015 0.0017 0.002 0.0023 0.0026 0.0031 0.0035 0.004 0.0046 0.0053 0.0061 0.0069 0.0079 0.009 0.0102 0.0115 0.0131 0.0148 0.0167 0.0188 0.0213 0.024 0.027 0.0304 0.0342 0.0384 1.506 1.541 1.576 1.611 1.646 1.6811 1.7161 1.7511 1.7861 1.8212 1.8562 1.8912 1.9262 1.9612 1.9963 2.0313 2.0663 2.1013 2.1364 2.1714 2.2064 2.2414 2.2764 2.3115 2.3465 2.3815 2.4165 2.4516 2.4866 2.5216 2.5566 2.5916 2.6267 2.6617 2.6967 2.7317 2.7668 2.8018 2.8368 2.8718
P a g e | 136 0.0246 0.0277 0.0312 0.0351 0.0396 0.0447 0.0506 0.0573 0.0652 0.0745 0.0856 0.0991 0.1161 0.1384 0.1701 0.2235 0.9116 0.0432 0.0486 0.0547 0.0616 0.0695 0.0784 0.0887 0.1006 0.1144 0.1306 0.1501 0.1738 0.2036 0.2428 0.2984 0.3921 1.5994 2.9068 2.9419 2.9769 3.0119 3.0469 3.082 3.117 3.152 3.187 3.222 3.2571 3.2921 3.3271 3.3621 3.3972 3.4322 3.4672 5.3089 5.305 5.3007 5.2957 5.2901 5.2836 5.2762 5.2677 5.2578 5.2461 5.2321 5.2151 5.1936 5.1655 5.1255 5.0582 4.1902 0.0432 0.0486 0.0547 0.0616 0.0695 0.0784 0.0887 0.1006 0.1144 0.1306 0.1501 0.1738 0.2036 0.2428 0.2984 0.3921 1.5994 2.9068 2.9419 2.9769 3.0119 3.0469 3.082 3.117 3.152 3.187 3.222 3.2571 3.2921 3.3271 3.3621 3.3972 3.4322 3.4672 1.8027 1.8033 1.804 1.8048 1.8057 1.8067 1.8078 1.8091 1.8107 1.8125 1.8146 1.8173 1.8206 1.825 1.8311 1.8416 1.977 0.0432 0.0486 0.0547 0.0616 0.0695 0.0784 0.0887 0.1006 0.1144 0.1306 0.1501 0.1738 0.2036 0.2428 0.2984 0.3921 1.5994 2.9068 2.9419 2.9769 3.0119 3.0469 3.082 3.117 3.152 3.187 3.222 3.2571 3.2921 3.3271 3.3621 3.3972 3.4322 3.4672
P a g e | 137
Chapter 10 References
The Aviation Partners Boeing Co. Unites states Patent. Blended Winglet, September 1994. http://www.boeing.com/commercial/757family/pf/pf_facts.html 3 Kennedy and R.C. Eberhart. Particle swarm optimization, in Proceedings of the IEEE International, Conference on Neural Networks, IV, pages 1942-1948. 4 A New Particle Swarm Optimiser for Linearly Constrained Optimisation, Ulrich Paquet, Andries P. Engelbrecht 5 ALLEN, J.E. Global energy issues affecting aeronautics: a reasoned conjecture, Progress in Aerospace Sciences, 1999. 6 Royal Commission on Environmental Pollution, The environmental effects of civil aircraft in flight, November 2002. 7 ALLEN, J.E. aviation and the environmental challenge, June 2003. 8 SMITH, H. College of aeronautics blended wing body development programme, Proceedings of ICAS 2000 Congress, Harrogate, September 2000, paper 1.1.4. 9 ICAO, Operational opportunities to minimise fuel use and reduce emissions, proposed ICAO Circular, CAEP/5IP/4, January 2001. 10 KUCHEMANN, D. The Aerodynamic Design of Aircraft, Pergamon, 1978. 11 http://www.boeing.com/commercial/757family 11 The Aviation Partners Boeing Co. Unites states Patent. Blended Winglet, September 1994. 11 http://www.boeing.com/commercial/757family/pf/pf_facts.html 11 ALLEN, J.E. Global energy issues affecting aeronautics: a reasoned conjecture, Progress in Aerospace Sciences, 1999. 11 Royal Commission on Environmental Pollution, The environmental effects of civil aircraft in flight, November 2002. 11 ALLEN, J.E. aviation and the environmental challenge, June 2003. 11 SMITH, H. College of aeronautics blended wing body development programme, Proceedings of ICAS 2000 Congress, Harrogate, September 2000, paper 1.1.4. 11 ICAO, Operational opportunities to minimise fuel use and reduce emissions, proposed ICAO Circular, CAEP/5-IP/4, January 2001. 11 KUCHEMANN, D. The Aerodynamic Design of Aircraft, Pergamon, 1978.
2 11 1
http://www.boeing.com/commercial/757family