This document describes the steps to set up a computational fluid dynamics (CFD) simulation of channel flow using commercial CFD software. It involves creating the geometry of the channel, meshing the domain, applying boundary conditions such as the inlet velocity and outlet pressure, and setting up the solver to model incompressible, isothermal flow using the k-epsilon turbulence model. The simulation will analyze channel flow at inlet velocities of 20, 40, and 60 m/s and compare the resulting static pressure contours on the mid-plane of the channel. This will help relate the phenomena of flow separation observed on missiles and aircraft to variations in static pressure.
This document describes the steps to set up a computational fluid dynamics (CFD) simulation of channel flow using commercial CFD software. It involves creating the geometry of the channel, meshing the domain, applying boundary conditions such as the inlet velocity and outlet pressure, and setting up the solver to model incompressible, isothermal flow using the k-epsilon turbulence model. The simulation will analyze channel flow at inlet velocities of 20, 40, and 60 m/s and compare the resulting static pressure contours on the mid-plane of the channel. This will help relate the phenomena of flow separation observed on missiles and aircraft to variations in static pressure.
This document describes the steps to set up a computational fluid dynamics (CFD) simulation of channel flow using commercial CFD software. It involves creating the geometry of the channel, meshing the domain, applying boundary conditions such as the inlet velocity and outlet pressure, and setting up the solver to model incompressible, isothermal flow using the k-epsilon turbulence model. The simulation will analyze channel flow at inlet velocities of 20, 40, and 60 m/s and compare the resulting static pressure contours on the mid-plane of the channel. This will help relate the phenomena of flow separation observed on missiles and aircraft to variations in static pressure.
Geometry Geometry 200 mm 2400 mm 600 mm 600 mm 600 mm Create Point Point Coordinat Create Point Translate Point in Z direction Create Curve Select 2 Point Create Surface Surface Part Name Create Surface Part Name INLET OUTLET WALL Surcface Part Name RIGHT CLICK Rename Select Surface Create Mesh Create Block Split Block Select This Edge Select This Point Split Block Check Block After Splitting Split Block Split Block Again Delete Block Unused Block Delete Block Associate Associate Associate Face To Surface Select Appropriate Face Node Distribution 50 30 20 100 30 Node Distribution Linear The Rest Edge :Parabola mid end Pre-Mesh Convert Mesh RIGHT CLICK: Convert to Unstruct Write Input File Solver Setting Import Mesh Analysis Type C Domain Setting C C C C C C C Isothermal : Incompressible (Continuity, Momentum Eqn) 101325 Pa K-epsilon Boundary Condition Boundary Condition Inlet BC : Subsonic Normal Speed : 10 m/s Turbulence : Medium Intensity Outlet BC : Average Static Pressure : 0 Pa Wall BC : No Slip Wall Solver Control C C Define Run Define Run Running Process Tugas 1 Cavity Flow Fenomena Cavity Flow http://www.marcodebiasi.net/MDresearch/MDpreviousresearch/cavityflo wphysics/A380.jpg Fenomena Cavity Flow http://upload.wikimedia.org/wikipedia/commons/c/c3/B-2_spirit_bombing.jpg http://twittervforce.com/blog/wp-content/uploads/2012/12/AVRO-VULCAN-XM655-BOMB-BAY-27-10- 12-1.jpg Tugas 1 : Cavity Flow a b c d e NIM 136 AB XYZ a = 1500+(YZ*10) mm b = 200+(YZ*5) mm c = 400+(YZ*10) mm d = 2500+(YZ*10) mm e = 1000 mm f (arah z ) = 2000 mm Kecepatan Aliran : 20, 40, 60 m/s Tugas 1 : Cavity Flow Pertanyaan Tampilkan kontur tekanan statik di tengah-tengah channel (Middle XY Plane) untuk semua kecepatan (Pada Pilihan Plane, Colour Gunakan Range : Local atau user specified, Bukan Global). Tampilkan velocity vector di tengah-tengah channel (Middle XY Plane) untuk semua kecepatan Bandingkan tekanan statik di Middle XY Plane untuk semua kecepatan, lalu hubungkan dengan fenomena separasi pada missile/bompesawat. Kerjakan berkelompok. Pilih satu NIM anggota kelompoknya. Laporan Dikumpulkan 26 Feb 2014 (2 Minggu).