A few things to keep in mind while completing this activity:
1. Do not use the browser Back button or close or reload any exam windows during the exam. 2. Do not close Packet Tracer when you are done. It will close automatically. 3. Click the Submit Assessment button to submit your work. Introduction In this practice Packet Tracer Skills Exam, you will: finish the configuration of a partially configured network establish connectivity to the East Region and the Internet through the use of static and dynamic routing Addressing Table Device Interface Address Subnet Mask Default Gateway WestHQ S0/0/0 172.16.100.245 255.255.255.252 S0/0/1 172.16.100.241 255.255.255.252 S0/1/0 209.165.201.2 255.255.255.252 S0/1/1 192.0.0.1 255.255.255.252 Lo0 10.0.0.4 255.255.255.255 W-Branch1 Fa0/0 172.16.100.1 255.255.255.128 n/a Fa0/1 S0/0/0 172.16.100.246 255.255.255.252 n/a Lo0 10.0.0.1 255.255.255.255 n/a W-Branch2 Fa0/0 172.16.100.129 255.255.255.192 n/a Fa0/1 172.16.100.225 255.255.255.240 n/a S0/0/0 172.16.100.242 255.255.255.252 n/a Lo0 10.0.0.2 255.255.255.255
n/a ServerFarm Fa0/0 172.16.100.193 255.255.255.224 n/a Fa0/1 172.16.100.226 255.255.255.240 n/a Lo0 10.0.0.3 255.255.255.255 n/a WPC1 NIC 172.16.100.126 255.255.255.128 172.16.100.1 WPC2 NIC 172.16.100.190 255.255.255.192 172.16.100.129 NetAdmin NIC 172.16.100.130 255.255.255.192 172.16.100.129 Payroll NIC 172.16.100.194 255.255.255.224 172.16.100.193
Note: The password for user EXEC mode is cisco. The password for privileged EXEC mode is class. Step 1: Finish the IP Addressing. Note: Initially, you can only access router W-Branch2 through the console connection on NetAdmin. a. Configure and verify interface addressing on W-Branch2. Configure and activate all interfaces for W-Branch2 that are listed in the addressing table. configure terminal interface fa0/0 ip address 172.16.100.129 255.255.255.192 no shutdown exit interface fa0/1 ip address 172.16.100.225 255.255.255.240 no shutdown exit interface se0/0/0 ip address 172.16.100.242 255.255.255.252 no shutdown interface loopback 0 ip address 10.0.0.2 255.255.255.255
b. Configure the correct IP addresses on WPC2 and W-Branch1. Configure WPC2 with the last IP address in the subnet. 172.16.100.129 255.255.255.192 direccin de la interfaz en el router /26 172 16 10 0 10|000001 AND 255 25 5 25 5 11|000000 172 16 10 0 10|000000 Direccin de red 172.16.100.128 direccin de red 2 6 = 64 Subred 1 172.16.100.128 broadcast 172.16.100.191 Rango ips 172.16.100.129 - 172.16.100.190 Subred 2 172.16.100.192 WPC2 172.16.100.190 255.255.255.192 Default Gateway 172.16.100.129 Configure the Fa0/1 interface on W-Branch1 with the last IP address in the subnet. 172.16.100.225 255.255.255.240 direccin de la interfaz en el router WB2 /28 172 16 100 1110|0001 AND 255 255 255 1111|0000 172 16 100 1110|0000 Direccin de red 172.16.100.224 direccin de red 2 4 = 16 Subred 1 172.16.100.224 broadcast 172.16.100.239 Rango ips 172.16.100.225 - 172.16.100.238 Subred 2 172.16.100.240 WB1 en fa0/1 172.16.100.238 255.255.255.240
c. Verify connectivity. Step 2: Discover the Network. Explore the network to determine the IP addressing of the serial interfaces that WestHQ shares with W-Branch1 and W-Branch2. En WB2 la interface se0/0/0 tiene la ip 172.16.100.242 255.255.255.252 WHQ IP 172.16.100.241 Remotely access WestHQ. WB2#telnet 172.16.100.241 Step 3: Configure Static and Default Routing. a. Configure connectivity to the East Region. Using the next hop address 192.0.0.2, configure one summary static route on WestHQ for the entire East Region. The East Region subnets are listed in the following table:
East Region Subnets 192.168.0.0/25 192.168.0.128/25 192.168.1.0/26 192.168.1.64/26 192.168.1.128/26 192.168.1.192/27 192.168.1.224/28 192.168.1.240/30 192.168.1.244/30 192.168.1.248/30 192.168.1.252/30
Se coloca en binario el o los octetos que cambian se deja igual hasta lo comn y de resto todo en cero. La mascara es hasta lo comn. Direcciones originales
Direccion de red sumarizada 192.168.0.0 /23 255.255.254.0 Ruteo estatico por siguiente salto para direccin sumarizada ip route 192.168.0.0 255.255.254.0 192.0.0.2 Configure a default route on WestHQ to send to the Internet all other traffic for destinations that are not found in the WestHQ routing table. Use the outbound interface argument. ip route 0.0.0.0 0.0.0.0 se0/1/0
b. Verify static and default routing. Probar ruteo -- Todas deben dar ok WHQ#ping 64.100.1.1 WHQ#ping 192.168.1.66 WHQ#ping 192.168.0.1 WHQ#ping 192.168.0.129 WHQ#ping 192.168.1.1 Step 4: Configure OSPF Routing. a. Configure OSPF on WestHQ, W-Branch1, and W-Branch2. Use OSPF process ID 1 and area 0. router ospf 1
Advertise each subnet individually with its corresponding wildcard mask. On WestHQ, do not advertise the subnet to the Internet or the subnet to East Region. 255.255.255.255 255.255.255.252 0. 0. 0. 3
network 172.16.100.245 0.0.0.3 area 0 network 172.16.100.241 0.0.0.3 area 0 network 10.0.0.4 area 0
Disable OSPF updates out interfaces where there are no OSPF neighbors available. WB1(config)#route ospf 1 WB1(config-router)#passive-interface fa0/0 WB2(config)#route ospf 1 WB2(config-router)#passive-interface fa0/0
Configure WestHQ to send the default route to W-Branch1 and W-Branch2 in OSPF updates. Default information b. Modify the default OSPF operation. Configure W-Branch1 to always be the DR by using a priority of 100. Configure W-Branch2 to always be the BDR by using a priority of 50. Change the hello interval to 20 seconds on W-Branch1 and W-Branch2 for the LAN that these two routers share with ServerFarm. Verify OSPF neighbor status. c. Verify that OSPF is fully operational. Verify that the routing tables on W-Branch1, W-Branch2, and WestHQ contain all the expected routes. It may be necessary to shutdown and then reactivate interfaces to force OSPF to converge. Step 5: Verify Full Connectivity. Although these are not scored, the following connectivity tests should be successful. To test the static route to East Region, successfully ping between WestHQ and EPC1. To test the OSPF neighbor establishment with ServerFarm, successfully ping between WPC1 and Payroll. To test end-to-end connectivity between the East and West Regions, successfully ping between WPC2 and EPC3. To test the default route, successfully ping the Cisco Server from NetAdmin.
The British and French Mandates in Comparative Perspectives Les Mandats Francais Et Anglais Dans Une Perspective (Social, Economic and Political Studies of The Middle E