Professional Documents
Culture Documents
API 2W Grade 50
TMCP Structural Steel Plate
General Product Description
API 2W Grade 50 is an intermediate-strength, structural steel plate, produced by thermo-mechanical
control processing (TMCP),that is used in the welded construction of offshore structures. API 2W Grade
50 has a minimum yield strength of 50 ksi [345 MPa] and a minimum, mid-thickness, transverse Charpy
V-notch impact toughness of 30 ft-lbf [41 J] at -40F [-40C]. SSAB is an API Licensee under the API
Monogram Program.
Applications: API 2W Grade 50 is intended primarily for use in offshore structures in critical portions
that must exhibit good impact toughness and resistance to plastic fatigue loading and lamellar tearing.
The primary use of API 2W Grade 50 is in tubular joints, stiffened plate construction and other
intersections where portions of the plates will be subjected to tension in the through-thickness (Z)
direction.
Mechanical Properties
Tensile Testing is performed transverse direction according to API 2W requirements. The minimum
values are tabulated below:
Thickness, t
0.2% YS ksi [MPa]
UTS ksi [MPa], Elongation in 2
Elongation in 8
in. [mm]
min.
[50 mm], min. %
[200 mm], min. %
t1.00 [25.4]
50 - 75 [345 - 517]
65 [448]
23
18
t>1.00 [25.4]
50 - 70 [345 - 483]
65 [448]
23
18
Charpy V-Notch Impact Testing is performed on each plate using mid-thickness, mid-width, transverse
specimens tested in accordance with ASTM A673. The producer has the option of testing sub-size
specimens to any of the combinations of specimen size, energy requirement, and test temperature as
shown below:
Specimen Size
Specimen
Minimum
Minimum Single Test Temperature F
in.
Size, mm
Average Energy
Value Energy ft[C]
ft-lb [J]
lb [J]
0.394 x 0.394
10 x 10
30 [41]
25 [34]
-40 [-40]
0.295 x 0.394
7.5 x 10
30 [41]
25 [34]
-40 [-40]
0.197 x 0.394
5 x 10
30 [41]
25 [34]
-40 [-40]
0.295 x 0.394
7.5 x 10
23 [31]
19 [26]
-50 [-46]
0.197 x 0.394
5 x 10
15 [20]
13 [18]
-80 [-62]
Mn
Si
0.16
1.151.60
0.03
0.010
0.050.50
1.
2.
3.
Al,
Total
0.0200.060
Ni
Cr
Mo
Cu
Ti
Cb
0.75
0.25
0.08
0.35
0.0070.02
0.03
Manganese up to 1.65 (heat analysis) is permitted at the option of the material manufacturer
Nitrogen and Boron shall not be intentionally added
Nitrogen may be 0.013% max., if titanium if 0.010 to 0.012%
www.ssab.com
2,3
0.012
B2
0.0005
CE IIW Max
0.39
0.41
CE IIW Typical
0.36
na
Pcm Typical
0.16
na
Tolerances
Thickness, width, and length tolerances for API 2W Grade 50 steel plate are in accordance with the
requirements of ASTM A6. The flatness tolerance for as-supplied product is ASTM A6.
Delivery Condition
API 2W Grade 50 is supplied in the Thermo-Mechanical Control Processing (TMCP) condition.
Thickness, in [mm]
Up to 1.5 [38.1]
>1.5 [38.1] to 2.5 [63.5]
Up to 1.5 [38.1]
>1.5 [38.1] to 2.5 [63.5]
Up to 1.5 [38.1]
>1.5 [38.1] to 2.5 [63.5]
Up to 1.5 [38.1]
>1.5 [38.1] to 2.5 [63.5]
Consumables
AWS E7015-X, E7016-X,
E7018-X
AWS ER70S-X
AWS F7XX-EXXX-XX
AWS E7XTX-X
Supplementary Requirements
By agreement between the purchaser and plate manufacturer, the following Supplementary
Requirements may be specified on the purchase order: S1 (Ultrasonic Examination), S2 (Notch
Toughness Test at Lower Temperature), S3 (Additional Tension Test), S4 (Through-Thickness [ZDirection] Testing), S5 (Low Sulfur Steel for Improved Through-Thickness Properties), S7 (Low Nitrogen
Content for Improved Notch Toughness in Strain-Aged Condition), S8 (Strain-Aged Charpy VNotch
Impact Tests), S11 Preproduction Qualification, and S12 (Notch Toughness Using Drop Weight), S13
(Surface Quality) and S14 (Thickness Tolerance).
Contact Information
For sales information, please call 877-294-3858 (Southern USA & Mexico), 800-340-5566 (Western and
Central USA), 800-383-9031 (North Central USA), and 888-576-8530 (Northeast USA & Canada) or
consult www.ssab.com.
www.ssab.com