Professional Documents
Culture Documents
MAX31865
RTD-to-Digital Converter
General Description
Applications
Industrial Equipment
Medical Equipment
Instrumentation
VDD
VDD
DVDD
0.1F
BIAS
REFIN+
DRDY
REFIN-
SDI
HOST
INTERFACE
SCLK
RREF
ISENSOR
MAX31865
FORCE+
CS
FORCE2
SDO
RTDIN+
N.C.
CI*
RTD
DGND
GND2
GND1
RTDINFORCE-
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxims website at www.maximintegrated.com.
MAX31865
RTD-to-Digital Converter
ABSOLUTE MAXIMUM RATINGS
Voltage Range on VDD Relative to GND1.............-0.3V to +4.0V
Voltage Range on BIAS, REFIN+,
REFIN-, ISENSOR.................................. -0.3V to (VDD + 0.3V)
Voltage Range on FORCE+, FORCE2,
FORCE-, RTDIN+, RTDIN- Relative to GND1.....-50V to +50V
Voltage Range on DVDD Relative to DGND.........-0.3V to +4.0V
Voltage Range on All Digital Pins
Relative to DGND.............................. -0.3V to (VDVDD + 0.3V)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
SYMBOL
MIN
TYP
MAX
UNITS
VDD
CONDITIONS
3.0
3.3
3.6
VDVDD
3.0
3.3
3.6
V
V
Input Logic 0
VIL
-0.3
0.3 x
VDVDD
Input Logic 1
VIH
0.7 x
VDVDD
VDVDD
+ 0.3
VBIAS
350
10k
50
Analog Voltages
(FORCE+,FORCE2, FORCE-,
RTDIN+, RTDIN-)
Reference Resistor
Cable Resistance
Per lead
ELECTRICAL CHARACTERISTICS
(3.0V P VDD P 3.6V, TA = -40NC to +125NC, unless otherwise noted. Typical values are TA= +25NC, VDD = VDVDD = 3.3V.) (Notes 2
and 3)
PARAMETER
ADC Resolution
ADC Full-Scale Input Voltage
(RTDIN+ - RTDIN-)
Maxim Integrated
SYMBOL
CONDITIONS
No missing codes
MIN
TYP
MAX
UNITS
15
Bits
REFIN+ REFIN-
MAX31865
RTD-to-Digital Converter
ELECTRICAL CHARACTERISTICS (continued)
(3.0V P VDD P 3.6V, TA = -40NC to +125NC, unless otherwise noted. Typical values are TA= +25NC, VDD = VDVDD = 3.3V.) (Notes 2
and 3)
PARAMETER
SYMBOL
CONDITIONS
MIN
0
14
Bias Voltage
VBIAS
1.95
IOUT
0.2
IOUT P 5.75mA
(Note 4)
Common-Mode Rejection
50/60Hz Noise Rejection
mV/mA
IDD
Shutdown
LSB
+3
FV RMS
90
dB
dB
55
62.5
66
20
21
550
600
CIN
Logic inputs
IL
Logic inputs
VOH
IOUT = -1.6mA
VOL
IOUT = 1.6mA
ms
Fs
LSB/V
1.5
mA
3.5
mA
2.27
120
mV
6
-1
LSB
150
52
ms
LSB
Maxim Integrated
V
mA
17.6
2.06
5.75
IDD
Input Capacitance
nA
16.7
Power-Supply Rejection
Power-Supply Current (Note 6)
82
VBIAS
-3
UNITS
10
2.00
MAX
30
TYP
pF
+1
VDVDD
- 0.4
FA
V
0.4
MAX31865
RTD-to-Digital Converter
AC ELECTRICAL CHARACTERISTICS: SPI INTERFACE
(3.0V P VDD P 3.6V, TA = -40NC to +125NC, unless otherwise noted. Typical values are TA= +25NC, VDD = VDVDD = 3.3V.) (Notes 3
and 7) (Figure 1 and Figure 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
tDC
(Notes 8, 9)
35
ns
tCDH
(Notes 8, 9)
35
ns
tCDD
(Notes 8, 9, 10)
80
ns
tCL
(Note 9)
100
tCH
(Note 9)
100
SCLK Frequency
tCLK
(Note 9)
DC
tR, tF
(Note 9)
CS to SCLK Setup
tCC
(Note 9)
400
ns
SCLK to CS Hold
tCCH
(Note 9)
100
ns
CS Inactive Time
tCWH
(Note 9)
400
CS to Output High-Z
tCDZ
(Notes 8, 9)
tDRDYH
ns
ns
5.0
MHz
200
ns
ns
40
50
ns
ns
Note 2: All voltages are referenced to ground when common. Currents entering the IC are specified positive.
Note 3: Limits are 100% production tested at TA= +25C and/or TA= +85C. Limits over the operating temperature range and relevant supply voltage range are guaranteed by design and characterization. Typical values are not guaranteed.
Note 4: For 15-bit settling, a wait of at least 10.5 time constants of the input RC network is required. Max startup time is calculated
with a 10k reference resistor and a 0.1F capacitor across the RTD inputs.
Note 5: The first conversion after enabling continuous conversion mode takes a time equal to the single conversion time for the
respective notch frequency.
Note 6: Specified with no load on the bias pin as the sum of analog and digital currents. No active communication. If the RTD
input voltage is greater than the input reference voltage, then an additional 400A IDD can be expected.
Note 7: All timing specifications are guaranteed by design.
Note 8: Measured at VIH = 0.7V x VDVDD or VIL = 0.3 x VDVDD and 10ms maximum rise and fall times.
Note 9: Measured with 50pF load.
Note 10: Measured at VOH = 0.7 x VDVDD or VOL = 0.3 x VDVDD. Measured from the 50% point of SCLK to the VOH minimum of
SDO.
Maxim Integrated
MAX31865
RTD-to-Digital Converter
CS
tCC
SCLK
tCDD
tCDD
tCDH
tDC
SDI
A7
A6
A0
tCDZ
SDO
D7
D6
D1
D0
CS
tCWH
tCC
tR
tCL
tCCH
tF
SCLK
tCDH
tCH
tCDH
tDC
SDI
A7
A6
A0
D7
D0
Maxim Integrated
MAX31865
RTD-to-Digital Converter
Typical Operating Characteristics
(VDD = VDVDD = 3.3V, TA = +25C, unless otherwise noted.)
SUPPLY CURRENT vs. TEMPERATURE
(ADC AUTO CONVERSION MODE)
3
IDD (mA)
IDD (mA)
ANALOG IDD
(BIAS PIN UNLOADED)
2
MAX31865 toc02
MAX31865 toc01
ANALOG IDD
(BIAS PIN UNLOADED)
DIGITAL IDD
DIGITAL IDD
0
0
-50
50
100
150
-50
50
100
150
TEMPERATURE (C)
TEMPERATURE (C)
0
NOISE RESPONSE (dB)
120
CURRENT (nA)
100
80
60
40
50Hz
60Hz
-40
-60
-100
75
50
100
125
150
50
10
90
130
170
TEMPERATURE (C)
MAX31865 toc05
-40C
0.244
0.244
+25C
0.1C
ERROR
+100C
-0.244
MAX31865 toc06
0.488
ERROR ()
0.488
ERROR ()
-20
-80
20
+25C
-40C
0.1C
ERROR
+100C
-0.244
-0.488
-0.488
0
500
Maxim Integrated
MAX31865 toc04
20
MAX31865 toc03
140
50
100
150
200
250
300
350
RRTD ()
MAX31865
RTD-to-Digital Converter
SDO
CS
SCLK
SDI
TOP VIEW
DGND
Pin Configuration
15
14
13
12
11
GND1 16
10
GND2
N.C. 17
FORCE-
RTDIN-
RTDIN+
FORCE2
MAX31865
DRDY 18
DVDD 19
EP
ISENSOR
FORCE+
BIAS
REFIN-
REFIN+
VDD 20
TQFN
(5mm x 5mm)
Pin Description
PIN
NAME
BIAS
REFIN+
Positive Reference Voltage Input. Connect to BIAS. Connect the reference resistor between REFIN+
and REFIN-.
REFIN-
Negative Reference Voltage Input. Connect the reference resistor between REFIN+ and REFIN-.
ISENSOR
FORCE+
FORCE2
Positive Input Used in 3-Wire Only. When in the 3-wire connection configuration, connect to FORCE+.
When in the 2-wire or 4-wire connection configuration, connect to ground. Protected to Q50V.
RTDIN+
RTDIN-
FORCE-
10
GND2
11
SDI
12
SCLK
13
CS
14
SDO
Maxim Integrated
FUNCTION
Bias Voltage Output (VBIAS)
MAX31865
RTD-to-Digital Converter
Pin Description (continued)
PIN
NAME
FUNCTION
15
DGND
Digital Ground
16
GND1
17
N.C.
18
DRDY
Active-Low Push-Pull Data-Ready Output. DRDY goes low when a new conversion result is available in
the data register. When a read-operation of an RTD resistance data register occurs, DRDY returns high.
19
DVDD
Digital Supply Voltage Input. Connect to a 3.3V power supply. Bypass to DGND with a 0.1FF bypass
capacitor.
20
VDD
Analog Supply Voltage Input. Connect to a 3.3V power supply. Bypass to GND1 with a 0.1FF bypass
capacitor.
EP
Do Not Connect
Block Diagram
VDD
BIAS
DVDD
VDD
VBIAS
GENERATOR
VDVDD
REFIN+
SCLK
SDO
REFINSERIAL
LOGIC
DATA REGISTERS
ISENSOR
SDI
CS
FORCE+
DIGITAL LOGIC
FORCE2
3-WIRE
ONLY
RTDIN+
15-BIT
ADC
50V PROTECTION
RTDIN-
50/60Hz DIGITAL
SINC FILTER
DIGITAL
COMPARATOR
FOR
FAULT DETECTION
MASTER-INITIATED
FAULT-DETECTION
CYCLE
ADC STATE
MACHINE
DRDY
FORCE-
MAX31865
GND2
Maxim Integrated
GND1
DGND
MAX31865
RTD-to-Digital Converter
Detailed Description
Temperature Conversion
450
400
350
RESISTANCE ()
STRAIGHT-LINE
APPROXIMATION
300
250
200
RTD RESISTANCE
150
100
50
0
-200 -100 0
MAX31865
RTD-to-Digital Converter
Linearizing Temperature Data
For a temperature range of -100NC to +100NC, a good
approximation of temperature can be made by simply
using the RTD data as shown below:
Maxim Integrated
Overvoltage (> VDD) or undervoltage (< GND1) condition on FORCE+, FORCE2, RTDIN+, RTDIN-, or
FORCE- pins
10
MAX31865
RTD-to-Digital Converter
FAULT DETECTION
ALWAYS ACTIVE FAULT DETECTION
MONITOR PINS
IS FORCE+,
FORCE2, FORCE-,
RTDIN+, RTDIN-,
PINS > VDD OR <
GND
CONVERSION
INITIATED
PERFORM
CONVERSION
IS
RTD RESISTANCE
VALUE > HIGH
THRESHOLD
REGISTER
IS
RTD RESISTANCE
VALUE < LOW
THRESHOLD
REGISTER
FORCE-INPUT
SWITCH
REMAINS
CLOSED
IS VREFIN>
0.85 x VBIAS
100s
DELAY
100s
DELAY
OPEN
FORCEINPUT
SWITCH
IS VREFIN<
0.85 x VBIAS
210s
DELAY
CONFIGURATION
REGISTER SET TO
100X000Xb TO
END FAULT
DETECTION
CYCLE
FORCE-INPUT
SWITCH
CLOSED
IS RTDIN<
0.85 x VBIAS
100s
DELAY
Y
SET BIT D3 OF FAULT
STATUS REGISTER
SET BIT D0 OF RTD DATA
LSB REGISTER
MASTER-INITIATED FAULT-DETECTION CYCLE - MANUAL MODE
MASTER WRITES
100X100Xb TO
CONFIGURATION
REGISTER
FORCE-INPUT
SWITCH
REMAINS
CLOSED
100s
DELAY
IS VREFIN>
0.85 x VBIAS
100s
DELAY
OPEN
FORCEINPUT
SWITCH
DID
MASTER WRITE
100X110Xb TO
CONFIGURATION
REGISTER
IS VREFIN<
0.85 x VBIAS
100s
DELAY
END FAULT
DETECTION
CYCLE
CONFIGURATION
REGISTER SET TO
100X000Xb TO
FORCE-INPUT
SWITCH
CLOSED
IS RTDIN<
0.85 x VBIAS
100s
DELAY
Y
SET BIT D3 OF FAULT
STATUS REGISTER
SET BIT D0 OF RTD DATA
LSB REGISTER
11
MAX31865
RTD-to-Digital Converter
Internal Registers
1-Shot (D5)
When the conversion mode is set to Normally Off, write
1 to this bit to start a conversion. This causes a single
resistance conversion to take place. The conversion
is triggered when CS goes high after writing a 1 to
this bit. Note that if a multibyte write is performed, the
conversion is triggered when CS goes high at the end
of the transaction. If VBIAS is on (as selected by the
Configuration Register), the RTD voltage is sampled
when CS goes high and the conversion begins. Note
that if VBIAS is off (to reduce supply current between
conversions), any filter capacitors at the RTDIN inputs
need to charge before an accurate conversion can be
performed. Therefore, enable VBIAS and wait at least
10.5 time constants of the input RC network plus an
additional 1ms before initiating the conversion. Note that
a single conversion requires approximately 52ms in 60Hz
filter mode or 62.5ms in 50Hz filter mode to complete.
1-Shot is a self-clearing bit.
POR STATE
READ/WRITE
Configuration
REGISTER NAME
00h
80h
00h
R/W
RTD MSBs
01h
00h
RTD LSBs
02h
00h
03h
83h
FFh
R/W
04h
84h
FFh
R/W
05h
85h
00h
R/W
06h
86h
00h
R/W
Fault Status
07h
00h
D6
D5
D4
VBIAS
1 = ON
0 = OFF
Conversion
mode
1 = Auto
0 = Normally off
1-shot
1 = 1-shot
(auto-clear)
3-wire
1 = 3-wire RTD
0 = 2-wire or
4-wire
Maxim Integrated
D3
D2
Fault Detection
Cycle Control
(see Table 3)
D1
D0
Fault Status
Clear
1 = Clear
(auto-clear)
50/60Hz filter
select
1 = 50Hz
0 = 60Hz
12
MAX31865
RTD-to-Digital Converter
The Fault Detect Cycle bits (D[3:2]) self-clear to 00b
upon completion.
3-Wire (D4)
Write 1 to this bit when using a 3-wire RTD connection.
In this mode the voltage between FORCE+ and RTDIN+
is subtracted from (RTDIN+ - RTDIN-) to compensate
for the IR errors caused by using a single wire for the
FORCE- and RTDIN- connections. When using 2-wire or
4-wire connections, write 0 to this bit.
50/60Hz (D0)
This bit selects the notch frequencies for the noise
rejection filter. Write 0 to this bit to reject 60Hz and
its harmonics; write 1 to this bit to reject 50Hz and its
harmonics. Note: Do not change the notch frequency
while in auto conversion mode.
D2
CONFIGURATION REGISTER
WRITE (BINARY)
XXXX00XXb
No action
100X010Xb
100X100Xb
100X110Xb
WRITE ACTION
READ MEANING
X = Dont care
Maxim Integrated
13
MAX31865
RTD-to-Digital Converter
RTD Resistance Registers (01h02h)
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
RTD
Resistance
Data
MSB
LSB
Fault
Bit
Weighting
214
213
212
211
210
29
28
27
26
25
24
23
22
21
20
4096
2048
1024
512
256
128
64
32
16
Decimal
Value
16384 8192
BINARY
HEX
DECIMAL
0.025
0000 0110
0110 0110b
06h
66h
819
0.125
0010 0000
0000 0000b
20h
00h
4096
0.25
0100 0000
0000 0000b
40h
00h
8192
0.50
1000 0000
0000 0000b
80h
00h
16,384
0.75
1100 0000
0000 0000b
C0h
00h
24,576
0.999
1111 1111
1111 1110b
FFh
FEh
32,767
Maxim Integrated
14
MAX31865
RTD-to-Digital Converter
Fault Threshold Registers (03h06h)
Serial Interface
D7
D6
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
RTD
Resistance
Data
MSB
LSB
Bit
Weighting
214
213
212
211
210
29
28
27
26
25
24
23
22
21
20
16384
8192
4096
2048
1024
512
256
128
64
32
16
Decimal
Value
X = Dont care
D6
D5
D4
D3
D2
D1
D0
RTD High
Threshold
RTD Low
Threshold
REFIN- >
0.85 x VBIAS
Overvoltage/
undervoltage fault
X = Dont care
Maxim Integrated
15
MAX31865
RTD-to-Digital Converter
SPI bus. The inactive clock polarity is programmable
in some microcontrollers. The MAX31865 automatically
accommodates either clock polarity by sampling SCLK
when CS becomes active to determine the polarity of the
inactive clock. Input data (SDI) is latched on the internal
strobe edge and output data (SDO) is shifted out on
the shift edge (see Table 8 and Figure 5). There is one
clock for each bit transferred. Address and data bits are
transferred in groups of eight, MSB first.
CS
High
Write
Low
Read
Low
SCLK
SDI
SDO
Input disabled
Input disabled
High impedance
High impedance
CS
CPOL = 1
SHIFT
INTERNAL STROBE
SHIFT
INTERNAL STROBE
SCLK
CS
CPOL = 0
SCLK
NOTE: CPOL IS A BIT THAT IS SET IN THE MICROCONTROLLERS CONTROL REGISTER.
Maxim Integrated
16
MAX31865
RTD-to-Digital Converter
CS
SCLK
SDI
A7
SDO
A6
A5
A4
A3
A2
A1
A0
HIGH-Z
D7
D6
D5
D4
D3
D2
D1
D0
CS
SCLK
SDI
A7
SDO
A6
A5
A4
A3
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
HIGH-Z
CS
SCLK
WRITE
SDI
ADDRESS
BYTE
SDI
ADDRESS
BYTE
DATA
BYTE 0
DATA
BYTE 1
DATA
BYTE N
DATA
BYTE 0
DATA
BYTE 1
DATA
BYTE N
READ
SDO
Maxim Integrated
17
MAX31865
RTD-to-Digital Converter
DRDY
Applications Information
For operation in noisy environments, a filter capacitor
may be placed across the RTDIN+ and RTDIN- inputs.
After an overvoltage or undervoltage fault, after a fault
detection cycle, or after enabling VBIAS, always allow for
the settling time of the input filter before restarting the
DRDY
RTD REGISTER
CONTENTS
CONVERSION n
CONVERSION n+1
CONVERSION n+2
SDI
RTD DATA
ADDRESS
SDO
RTD DATA
CS
Maxim Integrated
18
MAX31865
RTD-to-Digital Converter
ADC Code = 15-bit ADC results from RTD Data registers
(01h02h)
Once the resistance of the RTD is known, the welldefined resistive properties of the selected RTD can be
RTD RESISTANCE
()
ADC CODE/32-256
(C)
-200
-175
-150
-125
-100
-75
-50
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
225
250
18.52
29.22
39.72
50.06
60.26
70.33
80.31
84.27
88.22
92.16
96.09
100.00
103.90
107.79
111.67
115.54
119.40
123.24
127.08
130.90
134.71
138.51
142.29
146.07
149.83
153.58
157.33
161.05
164.77
168.48
172.17
175.86
185.01
194.10
0BDAh
12B4h
196Ch
200Ah
2690h
2D04h
3366h
35EEh
3876h
3AFCh
3D7Eh
4000h
4280h
44FCh
4778h
49F2h
4C6Ah
4EE0h
5154h
53C6h
5636h
58A4h
5B12h
5D7Ch
5FE4h
624Ch
64B0h
6714h
6974h
6BD4h
6E30h
708Ch
7668h
7C3Ah
1517
2394
3254
4101
4936
5762
6579
6903
7227
7550
7871
8192
8512
8830
9148
9465
9781
10096
10410
10723
11035
11346
11657
11966
12274
12582
12888
13194
13498
13802
14104
14406
15156
15901
-208.59
-181.19
-154.31
-127.84
-101.75
-75.94
-50.41
-40.28
-30.16
-20.06
-10.03
0.00
10.00
19.94
29.88
39.78
49.66
59.50
69.31
79.09
88.84
98.56
108.28
117.94
127.56
137.19
146.75
156.31
165.81
175.31
184.75
194.19
217.63
240.91
Maxim Integrated
19
MAX31865
RTD-to-Digital Converter
Table 9. Temperature Example for PT100 with 400I RREF (continued)
TEMPERATURE
(C)
RTD RESISTANCE
()
ADC CODE/32-256
(C)
275
300
325
350
375
400
425
450
475
500
525
550
203.11
212.05
220.92
229.72
238.44
247.09
255.67
264.18
272.61
280.98
289.27
297.49
81FEh
87B6h
8D64h
9304h
989Ah
9E24h
A3A2h
A914h
AE7Ah
B3D4h
B922h
BE64h
16639
17371
18098
18818
19533
20242
20945
21642
22333
23018
23697
24370
263.97
286.84
309.56
332.06
354.41
376.56
398.53
420.31
441.91
463.31
484.53
505.56
Maxim Integrated
Power-Supply Decoupling
20
MAX31865
RTD-to-Digital Converter
Table 10. Decoding RTD Faults for 2-Wire Setups When Fault Bit in RTD Data LSB
Register = 1
FAULT
STATUS
BIT SET
D7
D6
DESCRIPTION OF POSSIBLE
CAUSE
Open RTD element
Shorted RTD element
RTDIN+ shorted low
CONDITION DETECTED
Measured resistance greater than High Fault
Threshold value
Full scale
Near zero
Open RTD
D5
Full scale
VREFIN- > 0.85 x VBIAS
DESCRIPTION OF
RESULTING DATA
Indeterminate
Indeterminate
Appear to be valid
Appear to be valid
Near zero
Indeterminate
Table 11. Decoding RTD Faults for 3-Wire Setups When Fault Bit in RTD Data LSB
Register = 1
FAULT
STATUS
BIT SET
DESCRIPTION OF POSSIBLE
CAUSE
CONDITION DETECTED
DESCRIPTION OF
RESULTING DATA
Full scale
Near zero
Full scale
Force+ unconnected
Indeterminate
Appear to be valid
Maxim Integrated
Near zero
Appear to be valid
Indeterminate
21
MAX31865
RTD-to-Digital Converter
Table 12. Decoding RTD Faults for 4-Wire Setups When Fault Bit in RTD Data LSB
Register = 1
FAULT
STATUS
BIT SET
DESCRIPTION OF POSSIBLE
CAUSE
CONDITION DETECTED
DESCRIPTION OF
RESULTING DATA
Full scale
Near zero
Full scale
Indeterminate
D4
Indeterminate
VREFIN- < 0.85 x VBIAS (FORCE- open)
Appear to be valid
Maxim Integrated
Indeterminate
22
MAX31865
RTD-to-Digital Converter
Typical Application Circuits (continued)
VDD
VDD
VDD
DVDD
0.1F
BIAS
REFIN+
DRDY
REFIN-
SDI
HOST
INTERFACE
RREF
ISENSOR
MAX31865
SCLK
FORCE+
CS
FORCE2
SDO
RTDIN+
N.C.
CI*
RTD
DGND
GND2
GND1
RTDINFORCE-
VDD
VDD
0.1F
DVDD
0.1F
BIAS
REFIN+
DRDY
REFIN-
SDI
HOST
INTERFACE
SCLK
RREF
ISENSOR
MAX31865
RCABLE
FORCE+
CS
FORCE2
SDO
RTDIN+
N.C.
RCABLE
CI*
RTD
RCABLE
Maxim Integrated
DGND
GND2
GND1
RTDINFORCE-
23
MAX31865
RTD-to-Digital Converter
Package Information
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX31865ATP+
-40C to +125C
20 TQFN-EP*
MAX31865ATP+T
-40C to +125C
20 TQFN-EP*
Maxim Integrated
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that
a +, #, or - in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but the
drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
20 TQFN-EP
T2055+5
21-0140
90-0010
24
MAX31865
RTD-to-Digital Converter
Revision History
REVISION
NUMBER
REVISION
DATE
10/12
Initial release
1/15
DESCRIPTION
PAGES
CHANGED
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and
max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
2015 Maxim Integrated Products, Inc.
25
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.