Professional Documents
Culture Documents
Manufacturing 32
Manufacturing 32
ATTENTION
USER OF THIS DOCUMENT
IS RESPONSIBLE FOR
DETERMINING CURRENT
REVISION LEVEL BEFORE
USING DOCUMENT.
Originated By:
Rick Chen
RF Test Engineer
Date
2015/1/30
Approved By:
Wilson Hsu
Quality supervisor
Date
2015/1/30
Approved By:
Anson Cheng
Technical Manager
Date
2015/1/30
Title
MTA_Setup Procedure For R7181-38
Document No.:
Rev.:
MFG-1232
Page:
1 OF 27
Document No.:
Title :
Rev.:
MFG-1232
Page:
2 OF 17
REVISION HISTORY
Revision
-
Change Description
New release
CO NO.
Date
CO-015167
2015/1/30
Title :
MTA_Setup Procedure For R7181-38
1.0
Purpose
Define setup procedure for package product R7181-38
2.0
Scope
R7181-38
3.0
Reference documents
R7181-38-WF-001
R7181-38-WF-002
4.0
Definitions
N/A
5.0
Procedure
5.1 Equipment setting
Document No.:
Rev.:
MFG-1232
Page:
3 OF 17
Document No.:
Title :
MTA_Setup Procedure For R7181-38
Rev.:
MFG-1232
Page:
4 OF 17
times
Figure 1
Press Y
Figure 2
Document No.:
Title :
Rev.:
MFG-1232
Page:
5 OF 17
5.3.2 Enter the correct production Test Program Name, i.e.R7181AI, and hit <enter>.
R7181AI
5.3.3 From the next menu choose pRODUCTION TEST for Final Test or qA TEST for
QA gate using the up/down arrow keys and hit <enter>.
Document No.:
Title :
MTA_Setup Procedure For R7181-38
Rev.:
MFG-1232
Page:
6 OF 17
5.3.4 For the first Production Run sequence you must choose dUAL SITE - for dual site ITA
board or sINGLE SITE -for single site ITA board from the menu option, using the
up/down arrow keys and hit <enter>.
5.3.5 Next, you must select HALT ON fAIL from the next menu option.
Document No.:
Title :
MTA_Setup Procedure For R7181-38
Rev.:
MFG-1232
Page:
7 OF 17
5.3.6 Next, enter the dash number marked on the device packages/ listed on Test LTC you
are testing, i.e. 38.
5.3.7 Next, enter the Lot Number as listed on the device package/ Test LTC.
Title :
MTA_Setup Procedure For R7181-38
Document No.:
Rev.:
MFG-1232
Page:
8 OF 17
5.3.8 Next, enter the re-test number, 0 is for 1st pass and 1 is for the re-test of failures.
Document No.:
Title :
MTA_Setup Procedure For R7181-38
Rev.:
MFG-1232
Page:
9 OF 17
5.3.10 Next, select the correct Temperature from the menu as indicated on Test LTC. Make
sure that the thermocouple temperature reading is 75C when testing at Hot Temperature.
Thermocouple should not be attached when Testing Room Temperature and Cold
Temperature
5.3.11 Enter DUT number for socket but please make sure that the DUT number for the two
socket is not the same and if you choose SINGLE TEST for item 4.4 only one socket
number to be ask.(Ex.DUT#1 - 0 and DUT#2 - 1)
Document No.:
Title :
MTA_Setup Procedure For R7181-38
Rev.:
MFG-1232
Page:
10 OF 17
5.3.12 You will now be asked to verify the information you entered, which is displayed on the
screen. If all the information is correct then enter Y.
5.3.13 If the information is not correct then do the following: enter N and using the up/down
arrow keys select the data field that needs to be changed. Hit <enter> and update it
accordingly. Hit the <enter> button to confirm the change. To leave this menu and start
testing hit the <ESC> key.
Document No.:
Title :
Rev.:
MFG-1232
Page:
11 OF 17
5.3.16 Make sure the device is oriented correctly: device marking is upside down in reference
to the front of the tester, as shown below.
5.3.17 Begin testing by either depressing the space bar, or the test button on the front panel of
the DST4 tester.
Document No.:
Title :
MTA_Setup Procedure For R7181-38
Rev.:
MFG-1232
Page:
12 OF 17
PASS/FAIL Observations:
FAIL
When the testing completes and the screen shows FAIL, and the red LED on the front of the DST4 ITA
is illuminated, hit the re-test button on the front of the DST4 tester, or hit r on the keyboard, to re-test
the device. Only do this once. If the screen shows FAIL, and the red LED on the front of the DST4 ITA
is illuminated again, remove the device from the left-hand socket and place it in the bin for all failing
devices.
After Test, separate REJECT parts with a red sticker /clip tray with proper label as rejects.
PASS
When the testing completes and the screen shows PASS, and the green LED is illumated, put the
device from the left-hand socket in the bin for all passing devices.
After Test, separate GOOD from REJECT parts with a green sticker / clip tray and properly label
as BIN1.
Document No.:
Title :
MTA_Setup Procedure For R7181-38
Rev.:
MFG-1232
Page:
13 OF 17
Title :
MTA_Setup Procedure For R7181-38
Document No.:
Rev.:
MFG-1232
Page:
14 OF 17
Title :
MTA_Setup Procedure For R7181-38
Document No.:
Rev.:
MFG-1232
Page:
15 OF 17
5.5.1.1 To start testing using the sensor, Place the thumb on the top slot shown on the Above
Figure labeled A) Motion Sensor for Test.
5.5.1.2 To perform a retest , Place the thumb on the bottom slot shown on the above Figure
labeled B) Motion Sensor to Re-Test.
Document No.:
Title :
MTA_Setup Procedure For R7181-38
Rev.:
MFG-1232
Page:
FRONT VIEW
BACK VIEW
16 OF 17
Title :
MTA_Setup Procedure For R7181-38
Document No.:
Rev.:
MFG-1232
Page:
17 OF 17
5.5.2.2 Press SPACE BAR to start the testing of the corresponding DST4 set on the above
Omniview setting. Press R for Re-Test
6.0
Appendix
N/A