Professional Documents
Culture Documents
Second Revision (May, 2004)
Second Revision (May, 2004)
Copyright Notice:
This book is copyright 2004 to Bruce Simpson and all commercial rights are reserved.
Anyone discovering a violation of these terms is requested to contact the author through the
webpage at http://aardvark.co.nz/contact/
Page 2
Foreword
Modern jet engines, like the ones found on large passenger aircraft or military fighters are
incredibly complex and expensive to make.
Built from thousands of individual parts, many of which are made from exotic alloys like
titanium and Inconel, these engines are a masterpiece of modern engineering.
But what if I was to tell you that there is at least one type of jet engine that has been around
for almost 100 years, can be built out of plain old steel using simple tools, and in some cases
has no moving parts at all?
Well its true and I am, of course, talking about the pulsejet.
In this book Ill do my best to explain how these engines work, how to build them, how to
improve on the basic designs and how they can be used to power all manner of vehicles from
model airplanes to gokarts.
In an attempt to make the information contained in this book accessible to the widest range of
people, Ive taken a few liberties in explaining some of the more complex concepts. Im sure
there will be physicists, engineers and mathematicians who will throw up their arms in disgust
when they look at how Ive presented some of this information.
My justification for this is that the majority of readers are probably not equipped nor interested
in wading through pages of complex mathematical formulas in order to understand some
aspect of a pulsejets operation. In such cases, I believe, its better to replace all this
complexity with a simple analogy or basic calculation that hopefully anyone can follow.
Another are of contention is the very explanation of how a pulsejet works.
Although there is some consensus on the basic mechanisms behind the operation of a pulsejet,
much of the detail is a topic of hot debate and disagreement. Wherever possible Ive tried to
present all sides to an argument but obviously I favor my own opinions which are based on
years of empirical observation and experimentation.
Page 3
Page 4
Contents:
How do pulsejets work?
The worlds simplest pulsejet
Pulsejets for models
How to design a pulsejet
Comparing intake valving systems
Making reed valves last
Fuel systems
Constructional techniques
Powering things with pulsejets
Schmidts contributions
Ignition systems
How to start a pulsejet
Valveless pulsejets
The design of valveless pulsejets
Improving pulsejet performance
Accidents and failures
A simple guide to anodizing
Making reed valves with electrochemical etching
Newtons third law
The Reynolds effect
The Bernoulli effect
The Coanda effect
Plans
Wacky ideas
Afterburning augmentors
A Little History and a Few Important People
The future of pulsejet technology
5
8
10
12
20
23
29
37
43
46
48
51
54
59
66
69
76
82
88
92
91
93
95
97
99
103
105
Page 5
Page 6
For a practical demonstration, find an empty bottle that has an opening about the size of your
finger or thumb.
Wet your finger or thumb and slide it into the neck of the bottle, allowing the air to escape as
you do.
Now remove your finger quickly.
Hear that sound? Thats the air rapidly bouncing in and out just like the springy ruler
vibrated when you let the free end go.
See how easy this jet engine stuff is?
Now that weve seen how Kadeancy works its time to explain how it becomes the driving
force behind a pulsejet engine.
The Pulsejet Engine Operating Cycle
Lets assume that a mixture of finely atomized fuel and air has just been ignited inside our
pulsejet.
The rapidly burning fuel generates gases such as carbon dioxide, carbon monoxide and watervapor. These gases take up far more room than the air and fuel alone did so pressure build up
inside the engine.
The heat generated by the combustion causes those gases to expand so the pressure is
increased even more.
Our pulsejet has become a container filled with pressurized gases just like the one described
previously.
Those gases now rush out the opening at the end of the engines tailpipe and in doing so, they
create thrust which pushes the engine (and whatever its attached to) in the other direction.
It was Benjamin Newton who first described this effect when he said for each and every
action there is an equal and opposite reaction.
A fraction of a second after the air/fuel is ignited and the hot gases have started flowing out
the tailpipe, the pressure inside the engine has dropped to match that of the outside air.
However, thanks to the Kadenacy effect, the gases keep flowing down the tailpipe and a partial
vacuum is created inside the engine.
At this point, two very important things start happening.
Firstly, the valves at the front of the engine open. Theyre pushed open because the air outside
the engine is at a higher pressure than that inside the engine. This pressure difference pushes
on the valve and causes them to move aside, thus allowing fresh air and fuel to enter.
Page 7
At the same time, those hot burning gases that were travelling down the tailpipe stop for an
instant then start travelling back towards the front of the engine driven by the air outside
which is at a higher pressure than that inside.
You can see that at this point, we have fresh air and fuel coming in the front and still-burning
gases coming back down the tailpipe.
Can you guess what happens when the two meet?
Thats right the whole cycle starts all over again when the flames and hot gases from the
tailpipe ignite the highly flammable mixture of air and fuel that has been sucked in through the
valves in the front.
And of course, as soon as that fuel ignites, the pressures generated push the valves at the front
of the engine closed, leaving the hot gases only one way to go out the back.
When a pulsejet is running, this whole process is repeated many times per second and it is this
repeated blasting of hot gases out the tailpipe that gives the engine its characteristic noisy bark.
Wasnt that simple?
Page 8
Page 9
Replace the lid and swirl the liquid around in the bottom of the jar a few times.
Remember that you need to run this little engine well away from anything that could catch fire
and one suggestion I have is to dig a small hole in the ground so that the jar can be inserted,
leaving the lid slightly above ground-level. This will protect you and reduce the fire risk if the
jar should crack.
Now bring a lighted match or flame near the hole in the jars lid keeping your face and hands
well away from the area directly above that hole because a large flame may come shooting
out with a whooshing noise that can give you a bit of a fright.
It is highly recommended that you wear eye-protection and at least a long-sleeved cotton shirt
to protect yourself when performing this experiment.
If youre lucky, your simple little jam jar engine should start puffing away producing a
series of little pulses of hot gas and perhaps a gentle purring noise.
IMPORTANT: do not let this simple jam-jar engine run for more than 5-6 seconds at a time
or the glass will crack, possibly spilling burning fuel. You can stop it by covering the hole in
the lid with a small piece of wood or even a suitably sized coin.
How Does It Work?
Now the more observant reader will have noticed that this pulsejet has no valves so how
does it work?
The answer is simple when you ignited the air/fuel mixture that was originally in the jar it
burnt, expelling that large jet of flame and making that whooshing noise.
Because the hot gases rush out of the jar with great speed, the pressure inside the jar quickly
drops below normal atmospheric pressure and a weak vacuum is created just as described in
the previous chapter.
When this happens, a fresh gulp of air is sucked in through the hole in the lid and that air then
mixes with highly flamable methanol vapor that is rising from the pool of fuel still sitting in the
bottom of the jar. The jar once again contains a combustible mixture of air and fuel but how
does it ignite? After all, we had to use a match to ignite it the first time didnt we?
Well, also inside the jar are some remnants of the hot gases generated from the last
combustion cycle. Eventually the hot gases and the air/fuel mixture run into each other
whereupon ignition occurs, pushing its hot gases out the hole starting the whole cycle all over
again.
Hows that? Were not even a quarter way through this book and youve already built your
own pulsejet engine!
Page 10
Forty or fifty years ago there were a number of manufacturers producing small pulsejet engines
designed specifically for use on model aircraft.
Most of these engines are very similar in design and construction, consisting of a lightweight
stainless-steel body and tailpipe, with a machined aluminum head and thin spring-steel valves.
Quite a few of these engines were made in Eastern-bloc countries and at least one was made
by the OS model engine company in Japan.
However, perhaps the most recognized model pulsejet of all time is the Dynajet.
The Dynajet
Thousands of avid model airplane enthusiasts have owned, seen or lusted after this icon of the
pulsejet era.
The Dynajet was so popular, and so many were sold, that it rapidly became the benchmark
against which all other small pulsejets were compared.
Its simple design and lightweight construction made it perfect for use on model airplanes and
well suited to the U-control speed models of the era.
Even today the Dynajet is a popular item on auction website such as eBay, often producing
bids of several hundred dollars or more.
This picture is of an early
model Dynajet that had the
spark plug located right at the
rear of the combustion
chamber and didnt have an anodized head. In later models the sparkplug was moved forward
and the aluminum head was anodized a rich red color which resulted in the engine being
known as the Dynajet Red-head.
The body of these engines is made from two pressed stainless steel shells that are welded along
an upright seam. This technique results in a nice smooth contour between the combustion
chamber and the tailpipe, which probably helps the performance somewhat.
This picture shows the front of a later-model
Dynajet with a more deeply finned valve-head
section. You can clearly see the effects of the
red anodizing on the aluminum and the more
forward location of the sparkplug.
The company that used to make these
engines, Dynafog, is still in business but now
focuses on industrial fogging machines which
use the pulsejet principle to atomize and spray insecticide and other chemicals.
Page 11
Another company, Bailey Machine Service, is still making a clone of the Dynajet engine which
it sells for about US$250 although the supply is said to be somewhat erratic.
Many of the other pulsejet designs youll see from this era are very similar to the Dynajet in
size, dimensions and performance, although there are still plenty of weird and wonderful
variations on the basic theme.
The OS pulsejet
This engine was manufactured in the 1950s and 1960s by the Japanese company OS.
There were apparently
two slightly different
versions of this engine,
one being a little larger and more powerful than the other but they were both obviously very
similar to the Dynajet in both form and function.
However, unlike the Dynajet which used a single machined piece of aluminum for its valvehead and venturi, the OS unit consists of two separate
parts which screw together.
There was also a myriad of other pulsejet designs
manufactured about the same time and sold under a
raft of different names such as TigerJet, etc.
An even wider range of designs and ideas were
published as plans for a generation of enthusiasts
who, in a post-war era, were eager to build one of
these magical jet engines for themselves.
As a result, many magazines such as Popular Science and Popular Mechanics were littered with
advertisements for such plans.
It is unlikely that many of those who purchased these plans ever managed to construct a
working engine and at least a few of the designs were so fatally flawed that the publisher was
obviously just trying to cash in on a craze.
Page 12
The validity of this formula has been verified against a wide number of different and proven
pulsejet designs including the Argus V1 and Dynajet.
Lets take a look at what this formula actually means in terms of the way that the dimensions
of a pulsejet affect its power output.
We can see that if we kept the volume of the engine (V) constant but increased its effective
acoustic length (L) then the power would reduce. Note that in order to do this, the diameter
(and cross-sectional area) of the engine would need to be reduced so it would appear that
there is a definite relationship between cross-sectional area and power.
Now, if we keep the length (L) constant but increase the volume (V), the power would
increase. To accomplish this however, wed have to increase the diameter (and cross-sectional
area) of the engine. This confirms that relationship between cross-sectional area and power
output.
Page 13
If we manipulate that simple formula a little more, we come up with a new formula containing
a very interesting constant:
F = 2.2A
Where:
F = thrust (lbs)
A = mean cross-sectional area (square inches)
Lets just make an important point here this 2.2lbs/sq-in constant is derived from a formula
that includes the engines total volume as a factor. This is why its not just the cross-sectional
area of the tailpipe that is important (as many would have you believe), but the mean (average)
cross-sectional area of the entire engine along its total length.
However, it should be added that Tharratt didnt expect engines built to his formulas to have a
huge bulbous combustion area at the front so dont expect that such a feature will significantly
increase an engines performance over a straight pipe.
So now we can plug in our required power output of 10lbs thrust and get this:
10=2.2A
which simplifies to:
A=10/2.2
A = 4.545 square inches
From this we can calculate the mean diameter of our engine as follows:
D = 2(4.545/)
D = 2.4 inches
Now we need to decide on a length for the engine. Remember that making the engine longer
or shorter wont actually increase or decrease its power only a change to the cross-sectional
area will do that.
However, the length does have a bearing on the frequency at which our engine will operate.
The only reference I can find from Tharratt in respect to the suggested length of a pulsejet
engine is that it be at least eight times the mean diameter.
This length to diameter ratio is usually expressed as L/D and Tharratt notes that with
geometrical ratios of L/D < 7 the development problems become particularly challenging
and that in an engine with an L/D < 7 combustion with chemical fuels is difficult to
sustain, let alone develop maximum thrust
Page 14
It makes sense therefore, to use an L/D somewhat greater than 7 and its been my experience
that a figure of about 14 is a good place to start for relatively small engines like this.
By way of comparison, the Dynajet has an L/D of 15 and the Argus V1 has an L/D of 9.6.
As a rule of thumb, the smaller the engine, the higher the LD needs to be in order to get
reliable operation and good power levels.
So now we can calculate the length of our engine as follows:
L = 14D
L = 14 x 2.4
L = 33.6 inches
Okay, so now we know that to create a 10lb-thrust pulsejet engine well need a piece of pipe
that is 33.6 inches long and 2.4 inches in diameter -- but wait, theres more!
Another key formula presented by Tharratt was one for calculating the valve area for an engine
of a given size and power:
Valve area = 0.23 x mean cross-sectional area
Or
It is interesting to note that this 0.23 (or 23 percent) figure contrasts sharply with that
proposed by other pulsejet experts of the era who suggest a figure of 0.4-0.5 is better.
Lets use Tharratts formula and constant to work out the size of the valve area we need for
our 10lb-thrust engine.
Using the first formula we get:
Valve area = 0.23 x mean cross-sectional area
Valve area = 0.23 x 4.545
Valve area = 1.045 sq in
Using the second formual we get:
Valve area = 0.1045F
Valve area = 0.1045 x 10
Valve area = 1.045 square inches
Yep, we get the same answer both times so we now know that the effective valved area for our
l0lbs-thrust engine is just over 1 square inch.
Now Tharratts formulas assume that the intake is an open hole, with no losses due to the
presence of valves. Unfortunately, the presence of spring-steel reed valves will significantly
impact the flow of gas so we need to take those losses into account when designing our intake
valving system.
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 15
The precise efficiency of a valving system depends on many factors and I suggest you read the
chapter on intake valving for more information but in the case of our little design, lets use a
simple petal valve and assume that it is just 50 percent efficient.
To get the actual area of the valve required to achieve an effective area of 1.045 square
inches at 50 percent efficiency we simply divide by 0.5 to get a figure of 2.090.
So lets see how our pulsejet is looking like so far:
Thrust
Length (from valves to end of tailpipe)
Mean diameter
Total valve area (assuming 50% efficiency)
10lbs
33.6 inches
2.4 inches
2.090 square inches
Page 16
Weve decided to use a petal valve system consisting of 12 holes, each of 0.47 inches in
diameter. If we assume that the holes will be placed in a ring around the edge of the pipe, and
that we allow a certain amount of space between the holes so that theres room for the springsteel valves to rest, then we have a problem.
Lets assume we need a inch gap between the holes that means the total circumference of a
circle drawn through the center of each hole will be:
NumOfHoles x diameter + NumOfGaps x GapSize
And when we plug in our numbers we get:
12 x 0.47 + 11 x 0.25 = 8.39 inches
That represents a circle with a diameter of:
8.39/ = 2.67 inches
Whats more, that figure is the diameter of a circle that runs through the center of each hole so
we need to add two times the radius of the holes to get the size of a circle that will run around
the outer edge of the ring of holes.
2.67 + 0.47 = 3.14 inches
Clearly, the absolute minimum diameter of our valve system (3.14 inches) is larger than the
calculated diameter of our engines pipe (2.4 inches)
This disparity grows even further when we build in a bit of extra space so that the valves dont
scrape against the side of the engine when they swing open and closed. Its been my
experience that you should allow a space between the outer edge of the valve holes and the
side of the engine which represents an area equal to the total area of our valve holes.
Or in other words, we need to leave 2.090 square inches of space around our ring of holes.
That can be calculated as follows:
The area of a single circle covering our ring of valve holes would be:
R2 or 3.1415 x 1.57 x 1.57 = 7.74 square inches
Add 2 .090 square inches to get the size of the larger circle and we get 9.830 square inches
From this we can calculate the diameter needed to provide that extra 2.090 square inches of
space around the edge of the valve-ring:
Diameter = 2(9.830/)
Diameter = 3.53 inches
Is your head sore from all these calculations yet? Dont worry, were nearly done.
Page 17
Now that we know the diameter of our combustion chamber we need to calculate how long
this section of the engine should be.
Since Tharratt didnt use petal valves, he didnt need this bulbous front section so has no
advice (that I can find) for calculating this dimension.
However, we can look to the work performed by Schmidt (the guy who designed the Argus V1
engine) and my own empirical research that indicates the following:
During the intake phase of a pulsejets operation it will draw in a fresh charge of air equal
to 15%-20% of the total engine volume.
I see no reason why we shouldnt design the engine so that this front section is just large
enough to hold this fresh charge of air/fuel. In that case we need to do some more
calculations to determine its length:
If our engine were just a straight pipe of 33.6 x 2.4 inches then it would have a volume of
152.7 cubic inches. Such an engine would suck in 152.7 x 0.2 = 30.54 cubic inches of air
during each cycle so our front section needs to have a volume of 30.54 cubic inches.
Weve already calculated the area of this section as being 9.83 square inches we can calculate
the required length as follows:
30.54 / 9.83 = 3.11 inches.
Of course more alert readers will notice that this 30.54 cubic inches no longer represents 20
percent of the engines total volume. This is because by making this front section wider
without reducing the overall length of the engine, weve actually increased its total volume by
an additional 16.4 cubic inches.
The total volume of our engine is now nearer 169 cubic inches so the 30.54 cubic inch front
section only represents 18 percent of the total volume but this difference is so small as to be
unimportant.
The only thing remaining now is to join the front section of the engine to the tailpipe using a
cone with a diameter of 3.53 inches at one end and 2.4 inches at the other.
How long (ie: what angle) should this cone be?
Well if we look at the Dynajet we can see that its hardly a cone at all more of an abrupt
transition. By comparison, the Argus V1 engine uses a very long, shallow angled cone to join
the two sections. So how do we decide which is best?
Lets look at the effects that the angle of this cone might have on an engines operation.
Coming up with a suitable angle for this cone requires balancing a number of factors. To
examine them, lets look at extreme examples:
Page 18
1. If we simply used a flat plate to join the two sections of the engine then the hot exhaust
gases would have a rather torturous path to follow. Some of those gases would have to
travel around two 90 degree bends to get from the combustion chamber to the tailpipe and
that would potentially reduce the speed at which they were able to exit from the engine.
Remember, the speed at which the gases leave the engine affects the thrust we want
those gases leaving as fast as possible. For this reason, a flat plate is obviously not such a
good idea.
However, this configuration is not quite as bad as you might think, after all, the Dynajet
has a very steeply angled cone that must constrict the flow of exhaust gases right? The very
fact that it is so hard for the combustion gases to get into the tailpipe means that
immediately after ignition, pressure will build up inside the combustion chamber as all
those gases try to rush around a tight bend and down the tailpipe.. Those higher pressures
can improve combustion efficiency and actually increase the speed of the gases in the
tailpipe. This is called post-ignition confinement (PIC).
Its also worth noting that in the case of a flat plate, the hot gases that return from the
engine's tailpipe and ignite the fresh air-fuel charge may do so far more efficiently. This is
due to an interesting effect that occurs in the way they form a narrow jet that reaches deep
into the chamber rather than a larger diffuse front that ignites the fuel more slowly.
Remember that the faster the fuel burns, the more power our pulsejet will develop because
it will have less time to expand as it burns thus producing the higher internal pressures
that will, in turn, result in higher tailpipe gas velocities.
This diagram shows how ignition differs based on the angle of the cone between
combustion chamber and tailpipe. Note that in the second diagram, the distance between
the hot gases and the engine body is far less than in the first this is important.
The speed at which the combustion flame-front travels through the fresh air/fuel mixture
is relatively slow (just a few tens of feet per second) in a low-compression engine like the
pulsejet. Because of this, the mixture in the second diagram will be burnt far more quickly
than that in the first, since the flame-front will be wider with a much shorter distance to
travel.
2. If we used a very long cone that had a shallow taper all the way to the end of the engine (ie:
no tailpipe as such) --then it would obviously be much easier for the combustion gases to
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 19
flow out under pressure. However, wed also be significantly reducing the ability of the
engine to create a vacuum after combustion is completed because a much smaller
percentage of the exhaust mass would be travelling at maximum velocity inside the engine.
Remember that the force exerted by the escaping gases is equal to their mass times the
velocity to which theyre accelerated (F=MA). For a given size of engine engine, the mass
will always be the same but the velocity to which those gases are accelerated will depend
very much on the design of the tailpipe. We need plenty of velocity to get the force
required to establish a strong Kadenacy effect. In fact, tests conducted by the NACA
during the 1950s indicated that an engine designed with just a long convergent cone
instead of a straight tailpipe was very difficult to get running at all.
Once again it seems that a compromise is in order so well chose an angle of 30 degrees for the
section between the combustion chamber and the tailpipe. This will provide some postcombustion confinement to increase the internal operating pressures while ensuring that the
engine still has good internal mass-flow speeds to provide maximum Kadenacy effect.
A 30-degree cone will be a fairly short section just 1.84 inches long.
So here are the final dimensions of our pulsejet engine, wasnt that simple?
It should be noted that this is a very basic engine and there are still a few tricks we can use to
improve its performance but more of this later.
Page 20
One of the most critical components of a traditional pulsejet engine is the intake valving
system.
The demands placed on the intake valves are amazing.
They have to open and close several hundred times a second while being exposed to the
thermal stresses associated with being alternately blasted by searing hot combustion gases and
cold incoming air. At the same time, these thin strips of spring steel must resist metal fatigue
and fracture resulting from the high mechanical stresses imposed.
Whats more, they have to do all this while providing a 100 percent seal against combustion
gases when closed, and allowing the smooth, unimpeded flow of fresh air when open.
To make life even harder, the only power available to open them is the tiny difference in
pressure between the outside air and the small vacuum created inside the engine by the
kadenacy effect of escaping exhaust gases down the tailpipe. (just a few psi).
Its no wonder therefore, that no aspect of pulsejet design and construction has caused more
sleepless nights, scratched heads and frustration than the valving.
Lets examine the alternatives:
Petal Valves
Small engines almost always use a petal-valve. These valves offer the following benefits:
1. simplicity. The valve can be etched or cut from a single piece of spring-steel.
2. Low cost. As a side effect of their simplicity, petal valves can also be very economical to
manufacture especially when you consider that the valve plate consists of a simple piece
of aluminum with a ring of holes drilled in it.
Unfortunately, the petal valve also has a number of disadvantages:
1. poor aerodynamic performance. Since the air passing through a petal valve must negotiate
two near-90 degree bends on its way into the engine, the efficiency of such a system is not
particularly high.
2. low durability. Because the tips of the petals are directly
exposed to the hot combustion gases, petal valves often
suffer from premature tip cracking or fracture.
3. High maintenance. Since petal valves are usually made as
a single piece, the failure of individual petal requires the
replacement of the entire spring-steel valve.
Page 21
Despite their drawbacks, petal valves are generally the best option for small pulsejet engines,
although I wouldnt recommend them for any engine larger than about 20lbs of thrust.
The V or multi-V valve
Generally only seen on larger engines, these valves are
generally more efficient than petal valves because they
produce less deflection of the airflow when theyre in
an open position.
There are two basic methods of constructing such a
valve system one involves the use of two or more flat
metal plates with holes in them, joined at an angle (45
degrees is a good starting point).
The other method of forming a V valve is the one used
in the Argus V1 where a cast or machined spacer with
multiple ribs is used to hold the valves in position and limit their movement as in the diagram
below:
Page 22
Page 23
heat-damage
impact damage
fatigue due to flexing
A well designed valve system attempts to minimize all these factors so as to provide maximum
valve life but (woudnt you know it) there are always compromises involved.
Lets look at the simplest and easiest to solve issue first:
Fatigue due to flexing
This picture shows the effect of valve failure due to metal
fatigue brought about by the flexing motion of a petal valve.
Note that one of the petals has completely broken near the
root. Close inspection of this valve showed that stress cracks
were starting to appear at the root of the other petals. In this
case, failure was due to a poorly designed valve-retainer which
had an uneven radius of curvature.
Obviously, reed valves must flex in order to operate properly.
The key to avoiding premature failure however, is to limit this
flexing to a bare minimum and try to keep the flex radius as
large as possible.
To this end, the conventional petal-valve arrangement with a curved valve-retainer is quite
good providing the curvature of the retainer is of a constant radius.
If the valve retainer doesnt have an even, large radius curve to it, most of the valve flexing
will be concentrated over a small area near the root of the petal. In a fairly short space of time,
the stresses caused by this flexing will cause the spring steel to crack and fracture.
Page 24
Reduce the amount of valve travel. If the valves can open too far then they will reach a
much greater velocity when theyre closing and this will increase the forces applied to
them as they impact the valve seat. Of course limiting the valve-opening will also tend to
reduce an engines power as it means that less air can be drawn in during the intake phase.
Use a softer material for the valve-plate. Most small pulsejets already use an aluminum
alloy for the valve plate so theres not a lot of room for improvement here. However, the
NACA did conduct tests on engines which had a think coating of neoprene on the valveplates. This was said to almost double valve-life by reducing the impact shock
experienced by the closing valves.
Page 25
Note that although it might seem like a good idea to simply increase the amount that a valve
overlaps the hole it covers so that the air trapped between the valve and the plate acts as a
cushion to soften the impact, this is actually a bad idea.
If the overlap area is too great, the air cant get out of the way quickly enough and the tips of
the valves are actually bent backwards by this trapped air. As a result, tip fraying is
dramatically increased because any cracks that form grow very quickly due to this additional
stress.
Determining the ideal overlap area is something best done by trial and error. If the overlap is
too great then youll get premature fraying and poor engine performance (due to late closing
of the valves). If the overlap is too small then the valve plate will be damaged by the high
pressure loadings and this will ultimately affect engine performance because the valves will no
longer seal properly.
Heat Damage
Reed valves are usually made from hardened, tempered spring steel because its strong and will
return to its original position after flexing.
The problem with spring steel is that the hotter it gets, the softer it gets. If it gets too hot
then it will lose much of its strength and some of its springiness.
Unfortunately, the inside of a pulsejet engine is a very hot place and it is the pressure
generated by extremely hot (1,500 deg C) combustion gasses that actually cause the valves to
be closed.
So why dont the valves simply get red hot and go all floppy?
Well fortunately, the valves are only exposed to the hot combustion gasses for part of the
operating cycle. During the intake cycle theyre cooled by the incoming charge of fresh air.
In a petal valve setup, the valve retainer also provides a measure of protection from the heat
of combustion by shielding most of the valve from direct exposure to the hot gases.
However, the tips of the reed valves will still get hot and, as a result, they will become softer
than the rest of the valve. Whats more, the valve retainer will itself heat up once the engine is
running and some of this heat will be transferred to the valves when theyre open.
A number of solutions have been proposed to the problem of valve heating but most of them
will reduce an engines performance to some degree.
One of the simplest solutions is to place a flame-trap in the engine directly behind the valves.
This flame trap consists of little more than a mesh of stainless steel or some similar heatresistant metal.
Its well known that a metal mesh with suitably sized holes will not allow a flame to pass
through it but it will allow air and other gases to do so. This was the principle behind the
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 26
old miners safety lamps. Before the days of battery-operated flashlights, miners still needed
some form of illumination while working underground. A naked flame such as that from a
candle or oil lamp would pose a very real danger as it risked igniting underground pockets of
explosive gases such as methane.
By enclosing the flame in a metal mesh, the flame could not extend beyond that mesh so the
safety lamp could provide light and still be used without risk of sparking an explosion.
Now, the problem with a using a flame-trap mesh in a pulsejet is that in order to be effective,
the size of the holes in the mesh must be quite small. As a result, the mesh represents a
significant obstacle to the flow of the incoming fresh air charge. This means less air is drawn
in during each intake cycle so less power is produced..
Never the less, a flame-trap mesh is one way of making a relatively low-powered engine that
will run for far longer between valve-changes than a regular pulsejet.
Over the past two years Ive
given quite a bit of thought to
the issue of extending valve life
and have come up with two
ideas of my own.
The first is the Blast Ring
concept which works by
providing a physical shield
between the hot exhaust gases
and the valve tips.
By blocking the direct path of the combustion flame to the valve-tips, the operating
temperature of the valves is significantly reduced. However, because the Blast Ring has a very
large hole in the middle it doesnt restrict the flow of the incoming charge of fresh air to the
same degree as a flame-trap mesh.
This picture shows my PJ15 design running with a
Blast Ring in place.
Youll notice that the ring itself is glowing red-hot, an
indication that it is indeed absorbing much of the heat
that would otherwise be reaching the valves.
However, even this system imposes about a 15%-20%
performance penalty on the power levels that would
otherwise be obtained from an engine.
Another method for reducing the valve heating is to design the engine so that theres a buffer
of cold, dense air between the valves and the combustion gases. The easiest way to do this is
to inject the fuel into the combustion chamber some distance from the front.
Page 27
Page 28
Page 29
Fuel Systems
Next on the list of critical elements of a pulsejet must surely be the fuel system.
Atomization
Smaller engines such as the Dynajet have traditionally used a very crude form of carburetor
that using the incoming air to create a spray of rather coarsely atomized fuel droplets.
This atomizing process occurs right at the front of the engine when the incoming air is forced
through a slight venturi.
An Italian by the name of Bernoulli discovered that the faster air flows, the lower its pressure
becomes. This observation was promptly labeled (wait for it) the Bernoulli Effect.
The atomizer on these small pulsejets uses a venturi to squeeze the incoming air through a
narrowing in the intake. As it squeezes through, it has to speed up. As it speeds up the
pressure drops.
Now, if we stick a pipe carrying some fuel into the middle of this low-pressure area, the fuel is
literally sucked out and turned into a fine spray of droplets.
What could be simpler?
Unfortunately, although this system does work, the magnitude of the low-pressure area created
in the pulsejets venturi is quite small and this means that theres not much energy available to
suck that fuel through.
A Note About Atomization and Vaporization
Another problem with the simple atomizer is that the fuel droplets created tend to be very
large and therefore do not vaporize particularly well. It should be remembered that liquid fuels
themselves dont actually burn only the vapors that they emit will ignite. In order to obtain
good vaporization, the goal should be to create the smallest possible droplets because this
results in the largest surface area (from which vapor is emitted) for a given volume of liquid.
Fortunately however, the inside of a pulsejet engine is a very hot place so, despite the fact that
the simple atomizer does a poor job of converting liquid fuel into a nice fine spray, the high
internal temperatures of the engine greatly assist the conversion of those large droplets of fuel
into vapor.
[endnote]
The end result is that most of these small pulsejets are extremely sensitive to just where the
fuel tank is placed relative to the atomizer assembly.
If you place the tank too low then the engine wont have enough suck to pull the fuel up to
the atomizer nozzle.
Place the tank too high and gravity will draw the fuel through effectively flooding the engine.
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 30
Whats worse, even if you do get the engine running nicely, moving the fuel tank up or down
by even an inch or two can cause it to stop because the fuel flow is affected.
There are ways to reduce this sensitivity to fuel-head however and perhaps the simplest is to
use a pressurized fuel tank.
By delivering the fuel under pressure, the effect of a changing fuel-level is dramatically
reduced. The big problem is how do we generate this pressure?
One option is to simply pump some compressed gas into the fuel tank then seal it up. In
order for this to work, the tank should only be filled with fuel to only about 25 percent of its
capacity otherwise the pressure inside will drop significantly as the fuel is drawn off.
Alternatively, the compressed gas can be stored in a separate container and fed into the fuel
tank through a regulator. This is how the fuel system for the Argus engine that powered the
V1 flying bomb was configured and is illustrated in the diagram above.
Rather than rely on a large reservoir of compressed air
inside the tank, it is possible to tap into the pressure
produced by the combustion of the pulsejet itself.
This diagram shows how some of that pressure can be
directed into the tank to keep it pressurized. Note the
small reed valve that stops the pressure from leaking
back into the engine during the intake phase.
Page 31
In practice, the reed valve should be placed in the pipe that leads from the engine to the tank
rather than in the tank itself. Surprisingly, theres little risk that the hot gases from inside the
engine will ignite the fuel in the tank. This system can be used with both atomized and
injected fuel systems.
Another simple way to achieve fuel pressurization is to use something like a small balloon for a
fuel tank. This configuration is called a bladder tank. The elasticity of the balloon will
automatically pressurize its contents but be aware that some fuels will quickly break down
the rubber from which normal balloons are made and if it goes pop, youll have a very real
fire danger.
Some of those using pulsejets in model airplanes often use these bladder tanks to ensure good
pressurization and reliable fuel feed under varying G-forces. Its worth noting however, that
the rubber tank is usually contained inside another leak-proof container such as a plastic soda
bottle. This way, if the bladder bursts, the fuel remains contained
Most flyers of pulse-jet powered model airplanes also use a device called
a Cline regulator to ensure not only that the fuel pressure remains
constant but also to automatically shut off the fuel flow if the engine
stops unexpectedly.
You should also be aware that any leak in a fully pressurized fuel system
can result in large amounts of flammable liquid being dumped onto the
ground or in the general area of the engine. This is an obvious fire risk. Whats even worse is
that if the engine stops for any reason, the flow of fuel will continue to flood into what is now
a red-hot steel tube. That can result in a very impressive fireball that could also be very
dangerous.
Injection
Virtually all engines over 20lbs of thrust use direct fuel injection rather than atomization.
In such a system, the fuel is squirted directly into the engines combustion chamber under
some form of pressure.
This makes the engines operation far more reliable and adds the additional benefit that by
varying the amount of fuel being injected, the engines power can be varied. Yes, a throttleable
pulsejet!
The Argus V1 engine used direct injection but, to the best of my knowledge, no attempt was
made to provide any form of throttle control not that it would have been of any use on a
flying-bomb anyway.
The downside of fuel injection is that you need some method of pressurizing the fuel to force
it into the engine in a fine spray.
There are really only two options use a fuel pump or pressurize the entire fuel tank.
Page 32
The V1-flying bombs used the latter option and the fuel tank was pressurized using the same
compressed-air source which drove the missiles gyroscopes and other onboard systems.
Most of my injected engines use propane as a fuel because this has the advantage of being selfpressurizing. Your common BBQ tank has around 100psi of pressure in it so you can use this
for direct injection without the need for a supply of compressed air or a fuel pump.
Using such a system, the pulsejet remains a stand-alone engine that requires no extra bits and
pieces to keep it running.
The simplest injection system for a petal-valved engine
simply involves locating a cross-drilled injection nozzle
directly behind the valve-retainer plate.
This nozzle is drilled so that the incoming fuel is sprayed
out directly towards the side of the combustion
chamber. This ensures optimum mixing with the air and
(in the case of liquid fuels) means that any droplets of
fuel that arent vaporized by the incoming air will be
instantly flashed into vapor when they hit the hot
combustion chamber walls.
A more recent innovation Ive come up with however
involves placing an additional disk behind the valve
retainer, separated by just a small space.
By injecting the fuel in the
same radial pattern as
with the previous system
but between the two disks, the fuel is not only vaporized more
effectively but also serves to cool down the valve retainer disk
(and the valves). Building a system like this does however, require
access to a lathe in order to turn up the key component which is
this radial injector nozzle.
Using this double-disk setup Ive been able to double the life of the reed valves used in a petal
valve engine while also slightly increasing the engines performance and throttle range.
Timed Injection
One disadvantage of direct fuel injection is that simple systems such as the one used in the
Argus V1 engine tend to spray fuel throughout the engines operating cycle.
Fuel will only burn efficiently (or at all) when mixed with exactly the right amount of air. This
combustible mixture of air to fuel is referred to as the stoichiometric ratio and it varies
depending on the type of fuel being used.
Page 33
It makes little sense therefore, to waste fuel by injecting it when there is no incoming air to mix
with it as that fuel will be unable to burn inside the engine thus contributes nothing to the
thrust being generated.
Back in 1947, the guys at Princeton University came to this same conclusion and suggested
that using timed fuel injection would be a way to improve the fuel-efficiency of pulsejet
engines.
Now there are two ways in which timed fuel injection could be done: the simple way and the
complex way.
Given that the simplicity of a pulsejet is its single greatest virtue, Im all in favor of keeping a
timed fuel injection system simple too.
I regularly get email from people who think it would be a good idea to use an electrically
driven fuel injector like the ones used in modern car engines but I disagree.
In order to make one of these injectors work youd need a rather complex system that involved
a battery to drive the injector, sensors to measure the pressure inside the combustion chamber
for timing, and some electronics to tie the whole thing together.
This setup, although Im sure it could be made to work, would be costly, complex and offer
only minimal benefits over the system I use to obtain timed fuel injection.
Fortunately it is a simple job to synchronize the injection of fuel into the engine with the intake
of a fresh air charge. This is because the pressure inside the engine falls to below 1
atmosphere (14.7psi at sea-level) during the intake phase and rises to as much as twice
atmospheric (30psi+) during combustion and exhaust phases.
A valve placed over the fuel jet is sufficient to provide a degree of
injection timing and the addition of this mechanism can provide a
noticeable improvement in the fuel-efficiency of a large pulsejet.
Ive experimented with a number of different valved injectors ranging
from a simple bolt drilled length-wise with a flap of spring-steel over the
end like the one illustrated here
To this carefully machined injector made from stainless steel and
nickel-plated steel components I fitted to the 100lbs-thrust engine on
my gokart. I noted a very definite improvement in the fuel-efficiency
of this engine after fitting the timed injector system.
What Fuel is Best?
One of the great advantages of pulsejet engines is that they can, at least in theory, be made to
run on almost any type of combustible liquid or gas.
Page 34
Pulsejets arent limited to liquid or gas fuels however on at least two occasions, coal dust has
been used as a fuel. It is rumored that the Germans attempted to run the Argus V1 engine on
coal dust when liquid fuel supplies became almost unobtainable near the end of WW2 and
some of Reynsts pulsed combustors were designed specifically to use this unusual fuel.
Before you start worrying too much about what is the best fuel, its worth citing part of a
report published by Princeton University in 1947 that summarized a large amount of the
research done into pulsejet engines up to that time. It said the pulsating jet engine of
contemporary design ran on almost any common fuel with negligible variations in
performance.
The only caveat the report included was that principal [sic] differences were in the degree
of body heating and the rapidity of valve destruction.
They found that even the use of exotic fuels such as nitropropane or nitromethane offered
only a slight power increase at the expense of doubling an engines fuel consumption.
It makes sense therefore to choose your fuel on the basis of whatevers cheapest or most
convenient to use.
For most of us however, the choice of fuels is fairly simple and boils down to one of these:
Gasoline
This has the advantage that its relatively cheap, very easy to obtain, and is pretty clean burning.
Its also quite volatile so atomizes easily to promote easy starting.
Note that, contrary to what you might think, higher-octane gasoline is not going to produce
any more power than regular gasoline. In fact (in theory) it may produce slightly less power. If
you plan to use gasoline, just use whatevers cheapest.
Propane (LPG)
Thanks to the popularity of gas-fired BBQs, propane has also become quite easy to obtain and
suitable 20lb refillable tanks can be bought for well under $50.
In some countries, propane is even cheaper than gasoline and it burns very cleanly indeed
leaving no smell and very little residue at all. Despite the fact that its stored under pressure, it
is actually quite a bit safer to use than gasoline because its vapors dissipate very quickly in the
open air.
Since the boiling point of propane is well below normal room temperature, it either comes out
of the tank as a gas (thus avoiding the need for vaporization) or, when drawn off as a liquid,
instantly boils into a vapor. This makes a propane-powered pulsejet one of the easiest to start.
Note that bigger engines will almost certainly demand to be fed with liquid propane because an
average BBQ tank simply cant provide gas at a sufficiently high rate to keep up.
Page 35
If youre planning to use a BBQ tank of propane as a fuel, youll have get rid of the regulator
that is normally used to limit the flow of gas. This regulator reduces the pressure of the gas to
just a few psi, far too low for a pulsejets needs.
To give you an idea of just how much gas is needed to run a pulsejet, my own 15-lbs-thrust
engines (PJ15) will drink all the propane gas you can feed them with the regulator removed.
The Lockwood valveless engines will drink all the liquid propane you can feed them without
any regulator in place.
If you try to use propane without removing the regulator then all youll get from a pulsejet is a
few bangs and pops it wont run.
However, you will still need some form of control over the flow of gas into the engine and for
this I recommend buying a cheap propane/air torch of the type often used for soldering or
brazing.
These torches are available from almost any hardware
store and cost just $25-$30. Note that depending on
the exact make/model of torch you buy, you may
need to purchase an additional adapter fitting so that
it can be screwed directly onto a 10lb or 20lb propane
tank.
To use a torch like this as the gas-control valve for
your pulsejet, simply unscrew the burner fitting on the end and slide your propane-certified
plastic fuel pipe over the end, securing it with a small hose-clip.
The gas-flow knob on the torch will now enable you to control the amount of gas that is
delivered to your engine. If you invert your BBQ tank of propane, the torch will still serve as a
very simple way to control the flow of liquid propane to larger engines. Very simple, very
inexpensive, and very effective.
Another method of controlling the flow of propane
to your engine is to simply use a device called a
needle-valve. These valves are readily available from
a number of sources and, just like the gas-torch, offer
a very fine degree of control over fuel-flow.
Butane
It should be noted that although it is also often sold for use on small camp stoves, butane is
not a good substitute for propane. It contains less energy and doesnt produce as much
pressure as propane at room temperature. In short dont waste your time or money trying to
use butane as a fuel for pulsejet engines.
White Spirit/Coleman fluid
This is simply a very low octane unleaded form of gasoline which has no fancy anti-knock or
combustion improvemnet additives included. Its actually a better fuel than high-octane
Page 36
gasoline for pulsejet use. Many of the early small pulsejet engines such as the Dynajet run best
on this fuel.
Methanol
This is my second-favorite pulsejet fuel. It has the advantage that it will burn over a very wide
range of rich/lean mixture settings making an engine less sensitive to fuel head or starting
conditions.
It also burns very cleanly with no smelly or oily residue and creating little more than water
vapor and some C02 as combustion byproducts.
On the downside, methanol is more expensive than gasoline, your engine will burn more of it
for a given amount of power, and it can be very dangerous if spilled because it burns with an
almost invisible flame. Many people have been burnt because theyve walked straight into a
methanol fire without seeing it.
Despite the downsides, I prefer to use methanol for all my aspirated engines because it
generates a little more power, allows the valves to run cooler, and doesnt leave my hands
stinking of gasoline.
Note that you shouldnt use pre-mixed model airplane fuel instead of straight methanol.
Model airplane fuel contains up to 20% oil that will leave significant deposits inside your
pulsejet and also affects the vaporization of the mixture. Its also a lot more expensive than
plain old methanol so youll be wasting money.
Your local hot-rod or drag-racing club ought to be able to help you find a source of methanol
but if all else fails, try one of the major oil companies like Mobil they sell me 5-gallon drums
of the stuff when I want it.
Another thing to watch when using methanol as a fuel is that it is very hydroscopic which is
to say that it tends to absorb moisture out of the air. If you leave a can of methanol uncapped
then it may well absorb so much moisture that its combustibility is affected and this can result
in hard-starting.
Also be aware that when you use methanol as a fuel, one of the combustion byproducts is
water (albeit as water vapor). This means that the spring-steel reed valves used in an engine
run on methanol are prone to rusting unless you oil them lightly before storing your engine
after each run.
Page 37
Constructional Techniques
Once youve calculated the dimensions for a pulsejet, how do you then go about building one?
Of course It really helps if youve got access to a workshop or some basic metalworking tools
such as a hacksaw, drill, welder, etc. but dont be put off if your resources are a little more
modest.
Youd be surprised how helpful your local welder or engineer can be when you explain that
youre building a jet engine and would be happy to demonstrate it to them when its done.
Its also amazing what you can do with a minimum of tools if youve got enough patience.
The Engine Body/Tailpipe
Most commercial pulsejets are made from thin stainless steel sheet that is rolled or otherwise
formed into tubes and cones before being welded together.
This results in a durable engine that is light enough to be practical for such uses as powering
model airplanes.
These cones and tubes are formed using a device known as a slip-roll which looks rather like
an old washing-machine wringer and consists of three rollers that can be adjusted to both grip
and curve the metal sheet as its wound through.
A hand-operated slip-roll like this one is limited to rolling stainless steel that is no more than
1mm thick and even then its damned hard work if youre rolling a piece the full 600mm long
which is the maximum this set of rolls can handle.
For larger engines it really pays to find someone who has a set of motorized rolls that can
handle the thicker material and longer lengths youll need to use.
Page 38
Unfortunately, stainless steel is not only expensive but can also be very difficult to weld when
its very thin. For this reason, many enthusiasts prefer to make their engines from cheaper and
more easily worked materials
Providing weight isnt a problem you can save a lot of time and significantly simplify
construction by using mild steel pipe for the body of your engine. The best stuff is exhaust
tubing which is usually protected from rusting by a thin layer of aluminum on the surface.
This stuff is relatively cheap, available in a wide
range of sizes and can be cut and welded easily
using MIG, arc or oxy-acetylene equipment.
Unfortunately its also quite heavy, but thats usually
unimportant to the eager enthusiast who simply
wants to build an engine and get it running ASAP.
Heres a picture of my gokart with an engine built
from exhaust tubing. It only produced just enough
thrust to get the kart moving on a smooth surface
but it was an interesting experiment none the less.
As you can see, this pipe is quite thick-walled which accounts for its weight and easy welding
characteristics.
The Valving System
Exactly how you construct this depends on the type of valving system you plan to use. If you
have access to a lathe then you can easily make a petal-valve system with a nicely turned
aluminum head. If youre not lucky enough to have a lathe at your disposal, all is not lost.
Instead of making the front of the engine from a single, large piece of aluminum rod, you can
cut a circle from a sheet of plate. Even on small engines it pays to use a piece at least 3/8
(8mm) thick for this.
Because aluminum is such a soft metal, you can actually do a pretty good job of cutting a circle
from a flat sheet by using a jig-saw. You can even use a small coping saw or jewelers saw to
cut the valve holes (after drilling a starting hole first).
To create a circular valve-plate from a flat piece of aluminum, simply mark out your circle
using a compass then cut it slightly over-sized. It can then be filed down to a precise fit into
the front of your engine.
However, before you cut out the circle, it pays to mark out and drill the valve holes. By doing
this before you cut the circle to shape, you have a larger piece of metal to hold onto when
drilling the valve holes and this makes the job much easier.
Page 39
Page 40
While its simple enough to cut the rectangular shaped valves used in a V-valve system,
creating the intricate shape of a petal valve represents more of a challenge.
There are two methods you can use to fabricate a petal valve
from spring-steel sheet.
The first involves using a Dremel or similar tool fitted with a
cut-off tool as shown in this picture.
This technique requires a bit of practice and is most suitable
for smaller valves.
The preferred method for making petal valves involves the use
of a process known as electrochemical etching.
Full details of how to make reed valves using this process are provided later in this book.
Welding
There are really only two welding options when it comes to joining al the pieces together:
The ideal welding process is TIG, since this allows total control over the amount of heat used
and how much (if any) extra filler metal is added to the weld seam.
However, since TIG welders are more expensive than simple MIG units, and most people find
MIG welding much easier than TIG, Ill describe both processes.
Welding with MIG
I wont turn this into a welding tutorial so I assume
youll already be moderately competent with a MIG
welder. Instead, Ill focus on the points specific to
welding the various parts of these engines together.
It is important to use the right filler-wire. If youve
cut and rolled the parts out of 304 stainless steel
then you can use 308 or 316 stainless filler wire. If
youve cut your parts from 316 stainless then use
316 filler rather than 308.
Ive found that 0.8mm (0.032) wire is about the right thickness and you should only need a
small spool to build an entire engine.
While you can use plain steel wire, the resulting weld will rust very quickly and become weak,
so its not recommended. Stainless steel also has a much higher rate of thermal expansion than
plain steel so youll get additional stresses set up as the engine heats and cools.
Page 41
When welding, adjust the current, wire-speed and stickout used to try and get the flattest weld
bead you can without burning through.
I find when working with
very thin material (<
1mm/0.040)that sometimes
its easier to overlap the
material along the weldseam. If you plan to do this
then dont forget to allow
for that overlap when
marking and cutting your
pieces to size.
It also helps to have a chill
bar behind the weld seam
whenever possible. A length
of 25mmx25mm (1x1)
aluminum bar does a good
job here, with a length of 12.5mmx25mm used along the top surface to ensure intimate contact
between the two sides. A pair of two C-clamps can be used to hold everything together as in
this picture.
Welding with TIG
TIG welding thin stainless is not as easy as you might think.
The use of a chill-bar (as described in the MIG welding
section above) is absolutely essential. Without this, the
stainless will tend to sag and form ugly black danglers on
the back-side of the weld. This not only produces a weaker
weld but those danglers will also interfere with the gases
that flow at very high speed through these tubes.
Unfortunately, unless you want to go to the bother of
turning up conical chill-bars to match the radius of each
circumferential weld, youll have to just do your best
without one. Backpurging the weld with argon will
certainly help here, as will making sure that the fit-up of
the pieces is as near to perfect as you can get it.
Another option is to use a special high-temperature flux
paste designed for use with stainless welding. This usually
comes as a powder that is mixed with methyl alcohol then
spread on the backside of the weld to stop oxidation
during the welding process. The brand Ive used with
some success is Solar.
Page 42
Unless youve turned up those conical chill-bars, youre probably going to have to overlap the
cones slightly to get a good fit-up, since the rolling process combined with the stresses
produced when welding the length-wise seam, will almost certainly mean that the cones
themselves are not perfectly circular in cross-section.
When welding, try at all times to keep the weld bead the same thickness as the sheets being
joined. Its obvious why you would not want the weld to be too thin but read the piece on
heat-stress later in this bookto find out why a thick weld bead is just as bad.
Getting a Good Fit-up
A good fit-up is essential to the success of any welding job and there are some simple methods
of getting a good fit-up when assembling these engines.
Butting a cone up to a matching tube in such a way that the edges match perfectly so as to
ensure a good weld is a very difficult (some would say impossible) task when using very thin
material but fortunately there are alternatives.
I always flare or flange edges of my cones to ensure the maximum contact area between the
two parts and to ensure that the springiness of the stainless steel actually works to keep the
two surfaces in intimate contact for welding.
There are two ways of flaring and flanging you can use a rotary machine (sometimes called a
jenny) or you can just beat the snot out of it with a hammer and dolly.
If youve got a jenny then youre probably already aware of the techniques used to create flares
and flanges but if you dont, heres how you do things the manual way:
First youll need a good hammer (or two) and a dolly. Although I use the term dolly, I use
nothing more than a 100mm (4 inch) long piece of 25mm (1 inch) steel bar. Ive ground a
fairly large (6mm - inch) radius onto one end and a small recess onto the other [PICTURE].
This piece of metal is then used as a backstop as you beat the stainless into submission,
carefully working around the edge of the cone until the desired flare/flange is obtained.
If you do a good job, the cones and tubes should stay together before theyre welded without
the need for clamps or other mechanical devices.
Page 43
Page 44
Heres another boat powered by a huge Lockwood valveless pulsejet watch for it on your TV
screens sometime in 2004. No, I didnt build it or design the hull but I did design the engine.
Unfortunately it was not built very well and failed to produce anything like the power levels it
should have but you can still see that it does a good job of chopping up the water behind it.
Page 45
Helicopters
Back in the 1950s a number of experimental helicopters were designed that used tip-mounted
pulsejets to power the rotors.
None of these ever saw commercial production and they all suffered from a number of
problems. The arrival of the gas turbine turboshaft engine effectively killed off such ideas but
there are a number of places that will sell you plans for such suicide machines if you have a
death wish.
The NACA even published a research paper on the effects that the powerful centrifugal forces
experienced by a tip-rotor pulsejet would do to its combustion efficiency and reliability.
Civil Aircraft
Although Im not aware of any civilian light airplane that has used a pulsejet as its primary
source of power, valveless pulsejets were once used (mainly in Europe) to power highperformance sailplanes. Because these craft are so aerodynamically efficient, only a very small
amount of thrust is required to keep them airborne meaning that pulsejet power was almost
practical despite the high fuel-consumption.
Page 46
Schmidts Contribution
Earlier in this book I used Tharratts formulas, mainly because of all the designers, his work is
the most readable and easily applied by those without math and physics degrees.
However, Tharratt wasnt the only researcher who spent time working with pulsejets and many
others have come up with all manner of findings in relation to these engines.
Perhaps the most notable of these other pulsejet designers was a German by the name of Paul
Schmidt who was responsible for much of the Argus V1 engine.
Schmidt laid a lot of the groundwork from which others such as Tharratt made their
observations. In fact Id wager that there has been no other pulsejet engine in history that has
undergone as much prodding, poking and analysis as the Argus.
In the years after WW2 the US NACA invested a huge
amount of time and effort investigating the potential of
pulsejet engines and much of their work centered around
copies of the Argus. The US Air Force even commissioned
Ford to make a run of Argus engines to power a planned
1,000 flying bombs of their own carrying the designation
JB-2. Even the US Navy had its own version of the JB-2
which was more commonly known as the Loon.
Many of the NACA reports into the design and operation of the Argus have been released into
the public domain and have been included in the appendix of this book or can be downloaded
from the NACA archives on the Internet.
Like Tharrat, Schmidt was very much enamoured of engines designed around straight or
slightly divergent pipes. One such engine, designated the SR500, was little more than an
almost straight tube. I say almost straight because it was actually a cone that diverged by 2
degrees. With a total length of around 11 feet, this divergence meant that the, 18 inch diameter
at the front became 22 inches at the rear,
Despite its simple shape, the static performance of this engine appears to exceed that of the
Argus eventually used to power the V1.
The SR500 was reported to develop a static thrust of some 1,500 lbs which would result in a
performance of some 3.2 lbs thrust per square inch of mean cross-sectional area (some 50%
better than Tharrats constant). This would make the SR500 very efficient for a conventional
engine. I should not that Ive not had first-hand access to these reports but have no reason to
doubt their veracity.
Schmidt observed an interesting phenomenon during his pulsejet development work a rapid
mode of combustion that appeared to be much faster than regular deflagration. He went on to
spend much effort in trying to achieve true detonation but was ultimately unsuccessful.
Page 47
It is possible that this rapid combustion phenomenon goes some way to explaining the
seemingly extraordinary performance of the SR500.
My own experiments into promoting the simultaneous combustion of the entire air/fuel
charge within a pulsejet have also yielded very promising results. It looks as if Mr Schmidt
really knew how many beans makes two.
There is a lot more about Schmidts work along with the history of the V1 and Argus engine in
the other historical files on this disk.
Page 48
Ignition Systems
One of the great things about pulsejet engines is that, unlike the engine in your car, once
started, they dont require any regular source of timed ignition to keep running.
However, if theres one part of pulsejet starting that leaves many people scratching their heads
its how to create the spark needed to initially ignite the air-fuel mixture during that start-up
period.
I fit spark plugs to all my engines and have built a simple electronic circuit to create a suitable
spark but if you feel you dont have the necessary skills to do this there are alternatives.
One method Ive used before is still electrical but just uses parts you can get from any autowrecker or auto-electrical store.
All you need is an auto ignition coil, an auto flasher unit and a 12-volt battery.
Wire the three items together as in this diagram:
The component labeled C1 is a capacitor (or condenser) that stops arcing across the contacts
inside the flasher unit. Any auto parts store or wreckers yard should be able to supply this but
if not, you can use a 0.47 to 1.0 mfd capacitor rated to about 250V from Radio Shack or some
other electronic components store.
Its pretty easy to see that the signal light flasher turns off and on at regular intervals and this
on/off current flow causes the coil to create a nice bright spark. Theres not much to go
wrong here and there arent many mistakes you can make wiring it up so have a go. It might
be worthwhile adding an off/on switch and a fuse in the lead that goes from the battery to the
coil + connection.
Page 49
However, if youre comfortable working from electronic circuit diagrams you might want to
build the circuit below.
This simple circuit will drive a regular auto coil and produce a continuous stream of about 5-8
sparks per second. By comparison, the previous circuit may only produce one spark every
second or so.
Another alternative is to dispense with a spark plug all together.
Some people start their pulsejets by simply placing a lighted fireworks sparkler in the tailpipe.
I cant say Ive actually tried this myself but I dont see why it wouldnt work.
Apparently, once the engine starts, the sparkler wire is blown out the back so doesnt interfere
with the engines operation.
Of course if youre working on a new design or have an engine that refuses to start, you could
waste a lot of money on sparklers using this technique so having an electrically operated
ignition system is still a good idea.
One point that is seldom discussed is exactly where do you put the sparkplug?
Once again its compromise time!
Page 50
If you put the sparkplug towards the back of the combustion chamber then the engine will
probably start more easily because, by the time the air/fuel mixture reaches this point it will be
more thoroughly mixed and thus more explosive.
However, the the further back you place it, the greater the chance that the protruding plug will
interfere with the passage of the fast-moving exhaust gases.
Its worth noting that the original Dynajets had their sparkplug right at the back of the
combustion chamber just where it starts to taper down to join with the tailpipe. Later versions
saw the plug moved much further forward.
I tend to stick mine half way along the chamber and have no problems starting, nor do I see
any significantly adverse effect on power output.
And while on the subject of sparkplugs, what type should you use?
Well there are special miniature plugs available from companies like Champion, but Ive not
been able to find a source of such plugs at anything like a reasonable price.
So, I tend to use commonly available plugs that are originally designed for use on chainsaws,
weed-wackers and the like.
These plugs are much smaller than regular automobile units, but still use the standard 14mm x
1.25mm thread.
On a very small engine they may look somewhat out of place but on anything larger than an
8lb-thrust unit theyre just fine. Note that you will want to open up the gap to about twice the
factory setting before use. This will ensure easy starting.
Im sometimes asked whether its possible to use a model airplane engine glow-plug instead of
a sparkplug.
To be honest, I havent tried this but Im pretty sure it would only work if you were using
methanol as a fuel and even then youd probably find that it was pretty marginal.
Page 51
Page 52
Just supplying the engine with fuel is not enough -- you need to force some air into the intake
so as to create an explosive mixture inside the engine.
In the case of an injected engine, an air source such as a leaf-blower or vacuum-cleaner with a
blow attachment will likely do the job. You don't need a lot of pressure but you do need a
reasonable volume of air.
With an aspirated engine you'll need less volume but more pressure. This is because the air has
to draw the fuel up the fuel-line and atomize it into a fine spray before it passes through the
valves into the engine.
An air-gun driven by a compressor is perfect for the job. However, if you don't have such
luxuries available to you a great substitute is to inflate a car tube or tire without a valve in it -using a length of flexible plastic tubing slipped over the valve stem to deliver the air to the
engine's intake. The flow of this air can be controlled by kinking the tubing. Slipping a thinner
piece of pipe into the open end of the tubing will give you a narrower and more easily
controlled air-jet to spray into the engine. Between starting attempts you can replace the valve
and pump the tire up to 40-60 psi using a foot-pump or whatever. This is a great low-cost way
to start your engine at the flying field or away from other sources of compressed air.
The Ignition Source
The best ignition source is a spark plug mounted in the combustion zone section of the engine
but there are alternatives...
The simplest but least effective ignition source is a naked flame situated at the end of the
tailpipe. This could be a gas-torch or a spirit burner but you'll find starting an engine using this
method to be more difficult than with a sparkplug.
One other technique sometimes used when a sparkplug isn't mounted in the engine itself is a
spark-wand. This consists of two wires, separated by an insulator with a spark-gap at the end.
It is inserted and energized when starting the engine and quickly withdrawn once it is running.
A third option is to simply place a lighted fireworks sparkler into the engine. This will burin
for about 20 seconds and provide a nice hot ignition source. Try to place the sparker as far
towards the front of the engine as possible. It will be blown out when the engine starts.
Check the chapter in this book on ignition systems for more information and the plans for two
electrical ignition systems.
Putting It All Together
Here's the sequence for starting an aspirated pulsejet:
1.Connect the fuel line and tank. Make sure that the fuel level is no more than an inch or so
(20mm) from the engine's fuel jet (the hole where the fuel comes out into the engine).
2.Turn on the spark or light your ignition source
Page 53
3.Direct a jet of compressed air over the fuel jet so that it creates a fine spray of fuel droplets
that are then blown towards the engine's valves.
Note that it will take some experimentation, practice,
and coordination to get this right and you'll probably
find that it helps to move the jet of air back and forth
a little so as to vary the spray a somewhat.
If your engine has a flowjector setup like the
Dynajet then you wont be able to vary the angle or
position of your air source very much.
At this stage the engine should at least pop, bang or
burb a little, even if it doesn't immediately burst into
life.
If you don't get much activity, try richening the mixture a little (if your engine has this
capability) by losening the locknut and opening the mixture screw by a quarter of a turn.
Repeat this process until things improve. If they don't improve, return the screw to its original
position and try closing it a quarter turn at a time in case the mixture is already too rich.
The procedure is even simpler for an engine with direct LPG/propane injection.
Thanks to the fact that the fuel is already in the engine's combustion chamber, all we need do
is turn on the spark and blow some air into the intake.
If the engine doesn't fire immedately then the gas should be turned up or down until the
engine starts. If you still have trouble, try varying the amount of air being blown into the
intake.
Once you get the hang of starting a LPG-injected pulsejet its exceptionally easy to do
Page 54
Valveless Pulsejets
While most people marvel at the simplicity of the humble pulsejet with its single moving part,
there are designs that are even simpler.
I refer of course, to the incredible valveless pulsejet engine. A device that has absolutely no
moving parts at all!
The design of valveless engines is even more of a black art than the design of regular pulsejets,
as witnessed by the amazing diversity of shape and form to be seen amongst the various
valveless designs.
If youve performed the jam-jar experiment detailed elsewhere in this book then youve already
seen a valveless pulsejet engine in action, otherwise heres a brief description of how they
work.
Regardless of the shape, form and size of a valveless pulsejet engine, they are all basically a
combustion chamber with a pipe or pipes attached. Inevitably, one or more of the pipes is
much shorter than the other(s).
The short pipe is often referred to as the intake and the longer is referred to as the exhaust.
When the air/fuel in the engine explodes, hot gases rush out both pipes (yes, even the intake)
at great speed -- just as they rush out of a conventional pulsejets tailpipe.
When Mr Kadenacy pokes his head in to see whats happening, the rapidly exiting hot gases
create a partial vacuum inside the engine.
At this stage, the gas-flows reverse and the engine starts sucking back through its exhaust and
intake pipes.
Now, since the intake pipe is much shorter than the tailpipe, fresh air is able to be drawn into
the combustion chamber. It is then mixed with fuel (usually directly injected) and we have a
combustible mixture all ready to fire.
Meanwhile, gases continue to flow into the other end of the combustion chamber from the
exhaust pipe. Since the exhaust pipe is much longer than the intake pipe, these incoming gases
contain no fresh air just hot reminants of the previous combustion cycle.
As soon as these hot (still burning) gases hit the fresh air/fuel mixture boom the whole
cycle starts again.
Advantages
Its pretty easy to see that the biggest advantage of a valveless pulsejet engine is the fact that it
doesnt have any delicate valves to wear out or break. All else being equal, the operating life of
a valveless engine is limited only by the amount of fuel available and the durability of the
tubing from which its made.
Page 55
Without the need for valves, such an engine is also, at least in theory, much easier to make.
No holes to drill, no spring steel to etch just pipes and cones to weld together.
Disadvantages
Oh boy, didnt you just know this wasnt going to be a free lunch?
Thats right, theres always a price to pay in the pulsejet world and in return for its improved
simplicity of construction and operation, the valveless engine suffers from lower levels of
performance and efficiency.
Why is this?
Well youll recall that a little earlier on I mentioned something called post ignition
confinement (PIC) and mentioned that it sometimes had a beneficial effect on an engines
efficiency.
In the case of a traditional (valved) pulsejet engine, theres always a reasonable degree of PIC
because before the burning gases can expand, theyve got to push all that gas in the tailpipe out
of the way.
This slug of cold tailpipe gas provides a form of inertial confinement that ensures more
efficient combustion occurs in the front part of the engine.
However, when we look at a valveless engine there are now two (sometimes more) gaping
holes in the engine and in the case of the relatively short intake pipe, theres not a lot of cold
gas there to provide any reasonable level of inertial confinement.
So, when the air/fuel mixture in a valveless engine ignites, the gases are able to escape before
they can create the same pressure levels as youd find in a valved engine with its much smaller
escape route and the larger inertial mass in its tailpipe.
It is for this reason, plus the problems associated with making a valveless engine into a sensible
shape, that engines like the Dynajet continue to dominate the small pulsejet arena.
Perhaps the only valvless pulsejet that has ever enjoyed any success
is the oddly-shaped Lockwood Hiller design.
By bending the engine in half, Lockwood was able to have the
intake and exhaust pipes facing in the same direction so that they
both contributed to the total thrust.
Unfortunately this engine has never lived up to the claims that were
made for it.
Most notably its claim to provide an amazingly low (for a pulsejet)
fuel consumption figure have been independently verified despite
numerous engines having been built exactly to Lockwoods own plans.
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 56
Just to prove to myself that this weird engine doesnt live up to the claims made for it, I built
one that was supposed to produce 75lbs of thrust.
No matter how hard I tried, I could only
coax between 50 and 55 lbs of thrust out
of this beast and it used nearly four times
the amount of fuel claimed by Lockwood.
Several other people have verified this lack
of thrust and thirst for fuel so I think the
results are quite conclusive.
Of course having built such an engine, I
had to do something with it, so I stuck it
on my gokart just for fun. The only
problem is that a full BBQ tank of
propane only lasts about 5-6 minutes.
Here are just a few of the various valveless pulsejet engine designs that have been created over
the years:
The Reynst
This design was never
intended to create propulsive
thrust and was intended to
simply be a more efficient way
of burning fuel to create heat.
Its included here mainly
because its a great example of
the operating principles
behind pulsejet engines and
because its inventor (Reynst)
was such an important part of
pulsejet history.
The Marconnet
Designed almost 100 years ago, this engine, named after its inventor Frenchman Georges
Marconnet, is one of the oldest valveless designs. It seems to have relied on having a smaller
diameter intake tube than exhaust tube so that while some of the combustion gases escaped
out the front, even more rushed out the rear, producing a thrust imbalance that pushed the
engine forwards.
[diagram]
The Escopette
This was a logical evolution of the Marconnet and a similar engine known as the Resojet, the
major difference being that the Escopettes intake tube is bent through 180 degrees to point
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 57
towards the rear. By doing this, the gases that are ejected through this tube contribute to the
total thrust.
[diagram]
The Lockwood
This bend it in half theme was taken further by Lockwood except that he bent the exhaust
tube on his design which meant that the overall length of the engine was reduced by half.
This compact size and the ready availability of
plans has meant that Lockwoods engine is
perhaps the most popular valveless design
amongst amateur pulsejet builders.
The full patent application for the Lockwood
engine is included in an appendix at the end of
this book for those who are interested in the
exact theory of its operation.
The Chinese
I dont know how this engine got its name but its a simple design that follows the traditional
valveless design of having a long tailpipe and a short intake tube, both of which face towards
the rear of the engine.
From all reports, this engine is a rather poor performer, producing barely half the power of a
Dynajet despite being almost twice the size. Plans for a version of this engine are included in
the appendix of this book.
The Thermojet
Although it looks rather cool, the Thermojet was reportedly something of a disappointment in
terms of the amount of power it generated. As you can see, its not too much different to the
Chinese design except that it has two intakes that are parallel to the tailpipe. Note also that the
tailpipe has a fairly large flared cone. Some variants of the thermojet were built with as many
as four intake tubes.
Page 58
J. Kentifield, who played a major part in the design of this engine, claims that this design
produces more power per unit of length than a conventional valveless engine and a better
TSFC (fuel consumption) figure.
Details of the Calgary University engine can be found in a paper published by the AIAA with
the reference number AIAA 98-3879. This paper can be purchased from the AIAAs website
at www.aiaa.org
Page 59
Page 60
If there is too much choking then the thrust will be reduced. In fact, one of the interesting
things about trying to squeeze gas through a hole at high pressure is that youre limited by the
speed of sound.
Once the gas is pushed so hard that it reaches the speed of sound, no amount of extra pressure
will convince it to go any faster so this will mean our engine will not produce as much thrust
as it otherwise would.
Now I could go into the rather complex math required to calculate the exact size of hole
required to achieve the ideal speed of gasflow through the intake and exhaust tubes, but there
are a whole heap of variables that are often difficult to accurately predict. The reality is that
using a few rules of thumb and a bit of cut and try is sometimes a more practical way to get
things going.
The Intake Tube
The intake tube is the short one. Its shorter than the exhaust tube because it needs to be able
to pass enough air to pretty-much fill the combustion chamber during the engines intake
phase.
If the intake tube were too long, the engine would simply end up sucking back the exhaust
gasses that filled it during the last combustion phase.
However, the intake tube also needs to be long enough that it can hold a large enough slug of
cold, dense air to help contain the combustion gasses during the early phase of the combustion
cycle.
If the intake tube is too short, then it will contain only a limited mass that of cold dense air
when combustion occurs. This means the exhaust gases will rush out too quickly because
therell be little resistance to their flow. As a result, very little of the combustion gases will
actually be forced into the exhaust pipe and, as youll see in a minute, this will make it unlikely
that the engine will run.
The intake tube also has another subtle design feature its often slightly tapered, being wider
at the combustion chamber and narrower at the opening through which air is drawn in.
This is done for two reasons.
Firstly, this taper produces an additional choking effect during the combustion phase further
ensuring that theres plenty of pressure built up in the combustion chamber and that this
pressure forces a goodly proportion of the gases out the tailpipe.
Secondly, as the fresh charge is drawn into the engine, this shallow taper acts as a diffuser and
produces an increase in pressure within the engine. In order to get maximum combustion
efficiency we want the air/fuel mixture to be at as high a pressure as possible before ignition.
The taper of the intake tube has a small but useful effect in achieving this.
Page 61
Page 62
The mass of the gas in the tailpipe is determined by two things: the volume of gas and its
density (I told you there were many variables).
At this stage it would be very easy to simply use a straight pipe, equal in diameter to the hole in
the combustion chamber and long enough to hold sufficient mass of exhaust gas and indeed
this will work but not very well.
Not only would this tube be incredibly long (probably 30-40 times its diameter) but it would
also be very inefficient, thanks to the friction of the gases against the sides of this very long
tube and, more importantly for another reason.
Before we get onto that other reason, lets look at how we can increase the volume of the
tailpipe without making it unreasonably long
The obvious way is to increase its diameter since the volume of a cylinder is a function of its
length and its diameter.
However, we cant simply connect a big tube to the little tube coming out of the combustion
chamber as this would result in massive turbulence and huge inefficiencies due to that
turbulence.
The most logical way therefore, is to gradually transition from the small opening in the
combustion chamber to a larger diameter that produces a greater volume hence the coneshape so characteristic of a valveless engines tailpipe.
But back to that second important reason for using a cone
When the air/fuel in the engine ignites, the gases enter the tailpipe at great speed producing a
pressure wave that travels the full length of that tailpipe before escaping in to the surrounding
air.
Pressure waves are just another name for sound waves and, as anyone whos heard an echo
knows, they tend to bounce around under certain conditions.
What isnt so obvious however, is that when a pressure wave travels down a tube and reaches
the open end, some of its energy is reflected back down the tube not as a pressure wave but
as a rarefaction wave (a kind of negative pressure wave).
This rarefaction wave is a narrow band of low pressure that can be used to some advantage in
a pulsejet engine.
When the tailpipe is the correct length, the rarefaction wave produced by the escaping pressure
wave will assist in raising the strength of the vacuum formed in the combustion chamber
during the intake phase.
Whats more, the conical shape of the tailpipe actually serves to strengthen this rarefaction
wave as it travels towards the combustion chamber.
Page 63
If the tailpipe is too long, this wave will take too long to be reflected back to the combustion
chamber and its energy will be lost to the rapidly expanding pressure wave from the next
combustion cycle.
If the tailpipe is too short, this wave will arrive too soon and not interact optimally with the
partial vacuum caused by the momentum of the exhaust gases. Once again, this will result in
the energy being wasted rather than used to help draw in the next charge.
The optimal time for the arrival of the rarefaction wave is dependent on a raft of different
factors, including the volume of the combustion chamber, the flow-rate of the intake tube, the
shape of the combustion chamber etc.
So, with all this in mind, its obvious that the tailpipe length is important if we want to take
advantage of the rarefaction wave. If we can calculate the optimum length for the tailpipe then
it also becomes possible to calculate the angle of the cone so as to create the ideal volume
(aka mass) of gas in the tailpipe.
It is very interesting to note that valveless engines with very long tailpipes (such as the original
Ecrevisse) have a very shallow taper.
Looking at other (more modern) engines shows that the shorter the tailpipe becomes for a
given combustion chamber volume, the more acute the angle of taper (so as to hold a similar
volume/mass of gas). The Lockwood engine is a good example of a medium-taper tailpipe
and the Calgary one is an even more extreme example.
I hope you can now see that while its not too difficult to design a valveless pulsejet that will
run, its a whole lot more difficult to design one that will perform efficiently and which is
optimum in all respects.
For that reason, its probably a good idea to use a tried and tested design for your first
attempts.
Its also worth reiterating that, in the world of pulsejets, bigger is better. Dont be tempted to
build a tiny little engine or youll be almost guaranteed to fail.
A good size for a valveless engine is one with a combustion chamber of around four inches
(100mm) in diameter. Youll find the plans for a simple valveless engine of this size in the
plans section of this disc or you can scale the Calgary design to suit.
Flow Rectifiers
The final element in designing a valveless pulsejet engine is making sure that the gases from
the intake and tailpipe both exit the engine travelling in the same direction.
In the case of an engine such as the Lockwood, this is achieved by simply placing a U-bend in
the tailpipe. Unfortunately, the result is an engine which then has a really awkard and, for
some applications, decidedly non-aerodynamic shape.
Page 64
An alternative to this is to place a 180 degree bend in the intake tube but this is also not
without its problems namely the fabrication of a U-bend with a constantly tapering diameter.
Placing the u-bend in the intake also produces an engine that is significantly longer than the
Lockwood configuration.
Another alternative is something like the Chinese design or the Thermojet, where the intakes
are attached to the combustion chamber so that they already point in the same direction as the
tailpipe.
Unfortunately (wouldnt you know it), this also involves some compromises that tend to
reduce the power and efficiency of such engines.
One good idea is to use an external flow-rectifier which also doubles as an augmentor. Using
this concept, you can kill two birds with one stone. This approach does still require the
fabrication of a tapered u-bend and results in an even longer design than any of the other
methods.
Fuel Systems
As with all pulsejet engines, the manner in which fuel is mixed with the incoming air charge is
critical to performance.
Ideally we want to create a very turbulent swirling mixture of air and fuel mixed at the ideal
stoichiometric (combustible) ratio. It would also be extremely good if we could time the fuel
flow so as not to waste any by injecting it when the engine is in its exhaust or combustion
phases.
The first criterion is fairly easy to achieve, especially considering that the gases inside the
combustion chamber of an engine are going to be forced into turbulent flow patterns by the
rapid inrush of the cold charge. Its still a good idea however, to try and get the maximum
mixing of air and fuel without simply relying on combustion chamber turbulence to do the job.
Obtaining a good level of air/fuel mixing is pretty easy with a volatile fuel such as propane (see
the method commonly used for the Lockwood design) but quite a bit harder if you plan on
using a fuel such as diesel, kerosene or gasoline. These less volatile fuels usually require a good
atomizing nozzle and a relatively high-pressure fuel pump in order to achieve the levels of
mixing needed to provide efficient combustion.
The second objective of timing the flow of fuel is a little more difficult and, unless obtaining
the maximum fuel efficiency is important, generally not worth worrying about. It should also
be remembered that one of a pulsejets few virtues is its simplicity. If you start adding
complex timed injection systems you may gain some efficiency but at the cost of much
increased complexity.
Design Starting-points
The best way to design your own valveless pulsejet is to start with the basic dimensions of a
tried and true engine. This could be the SNECMA/Lockwood or the Calgary Universitys
shorter four-intake design and Ive presented the basic dimensions for all these here.
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 65
Note that Ive specified the dimensions in terms of ratios related to the diameter of the
combustion chamber (D). These ratios remain relatively constant for most sizes of engine,
except for very small engines (where D is less than 3 inches or 75mm) in which case Reynolds
numbers become so low as to cause problems.
Page 66
Page 67
Unfortunately, pulsejets dont have nice solid pistons to compress and confine the air/fuel
mixture prior to, or immediately after ignition.
The only thing compressing and confining our air/fuel mixture is the light, relatively
ineffective column of gas in the engines tailpipe. Clearly this column of hot gas is going to act
like much of a piston.
This is confirmed by measurements made inside a running pulsejet engine which indicate that
the fresh air/fuel charge is only compressed by a tiny amount (around 2psi) before it is ignited.
Other measurements indicate that the peak pressure generated inside the engine as the hot
burning gases push against the gas column in the tailpipe is a very modest 12-15psi.
Clearly design change that allows an engine to increase the operating pressures that are
generated inside it will have a positive effect on both power output and fuel consumption.
Some suggestions for obtaining higher operating pressures have included:
1. multi-point ignition to reduce the time taken to ignite the entire air/fuel load
2. the use of detonation waves to provide pre-ignition compression and much faster ignition
of the total air/fuel load
3. increasing the level of turbulence inside the engine so as to promote faster ignition of the
total air/fuel load
All of these are valid suggestions but none of them are easily achieved without compromising
some other aspect of the engines operation.
Multi-point ignition
The faster you can burn the entire air/fuel charge inside the engine, the more power will be
produced and the more efficiency will be obtained.
In a perfect engine wed be trying to obtain whats known as constant volume combustion
where the air/fuel charge isnt allowed to expand at all until its been entirely consumed. In
such an engine, the internal pressure generated will often be more than ten times that which
was present before ignition occurred.
If we have a pulsejet that achieves an internal pre-ignition pressure of just 2psi
The reason for this is simple the only thing stopping the burning air/fuel from escaping out
the rear of a pulsejet engine is the relatively light column of gas in the tailpipe. Being light, this
gas actually does a very poor job of stopping the air/fuel from
The most promising of these has been the use of a detonation wave to ignite the air/fuel load.
It is this concept that has spawned a whole new arm of pulsejet research and the development
of the pulse detonation engine (PDE).
Unfortunately, PDEs have yet to make it out of the laboratory and into practical application
anywhere. Although they do offer the promise of massive improvements in efficiency, they
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 68
are complex beasts that require a truckload of support gear in the form of pumps, valve
actuators, oxidizer tanks and much more.
Augmentors
The simplest way to
improve both the
static/low-speed thrust
and fuel-efficiency of a
pulsejet is to add an
augmentor to it.
Augmentors increase an
engines thrust through
two basic mechanisms:
1. Increasing the total mass-flow.
Since the amount of thrust generated by an engine is equal to the amount of mass it expels
times the amount of acceleration imparted to that mass, there are obvious gains to be had if we
can increase the total mass of air that gets ejected out the back (providing we dont slow down
the speed at which its ejected.
An augmentor draws cold air into the exhaust through the gap between the engine tailpipe and
the augmentor intake thus adding mass and increasing thrust. Because the hot exhaust gases
heat this cold air, it expands and therefore helps maintain the velocity of the exhaust gases.
2. The Bernoulli effect.
The front of an augmentor tube has a curved lip which serves two purposes. The first is to
make it easier for cold air to enter the gap between the tailpipe and the augmentor cone, the
second is to produce lift thanks to the Bernoulli effect. (see the chapter later in this book for
an explanation of what the Bernoulli effect is).
As the air passes around this curved lip, an area of low-pressure is formed and which means
that atmospheric pressure on the back of that lip effectively applies a forward force on the
augmentor adding to the total thrust produced.
When I added an augmentor to the intake tube of my standard Lockwood engine, the total
thrust produced jumped from 57lbs up to around 80lbs a very worthwhile improvement
indeed.
Page 69
Well the answer is that, providing sensible safety precautions are taken, running pulsejet
engines are no more dangerous many other activities.
In my five years of intensive experimentation, Ive only suffered one accident worthy of
comment, and that was simply a case of tripping over a propane tank and knocking myself
senseless on a concrete driveway.
Not Explosions but Implosions
What happens if that thing explodes is another question I frequently have to answer.
The truth is that pulsejets are far more likely to implode than explode.
The peak pressures encountered during combustion in a conventional pulsejet engine are less
than 50psi and average out to just a few psi across the entire operating cycle.
Page 70
Because the metals most often used for pulsejet construction (steel, stainless steel, etc) are
extremely strong under tension, they are very unlikely to burst, although I have had a few
engines that split after many hours of hard running.
Fortunately however, if a pulsejet engine develops a crack or a split it will usually stop instantly.
This is because pressure variations necessary for proper operation are disrupted by the leakage
that such a crack produces.
A good example of this can be seen in one of the videos on this disc where the Lockwood
engine on my jetkart stops abruptly because the sparkplug falls out. Even though the area of
resulting hole is tiny when compared to the areas of the intake and exhaust tubes, the leakage
that it produces immediately causes the engine to stop running completely.
The real problem, especially with valveless engines, is that during
the intake phase, the pressure inside the engine drops to very low
levels. This effect of this low pressure is further exacerbated by the
presence of a powerful rarefaction wave that travels back down the
tailpipe towards the combustion chamber.
When the pressure inside the engine is low, the material from
which it is made is placed under a different kind of stress namely
compression.
Whereas this metal is very strong under tension, it tends to be very
weak when placed under compressive loads. This means that, if
the proper construction techniques and materials arent used,
theres a very real risk of the tailpipe cone collapsing under the
effects of atmospheric pressure, as in the picture on the right.
The first sign of the failure was a gradual ovalling of the
tailpipe cross-section but when it failed it was
spectacularly quick and happened in the blink of an eye.
One second the engine was running nicely, the next it
was looking like someone had run over it with a
steamroller.
Even the smaller Lockwood engine I used on the gokart
had the same problem as seen in this picture
In this case Id made the tailpipe from 0.65 mm (0.026)
stainless steel and, although it did run fine for quite a
while, it eventually succumbed to the effects of
atmospheric pressure.
Page 71
Metal Fatigue
Next to implosions, metal fatigue is likely to be the most common mode of engine failure.
The metal from which a pulsejet is made takes an incredible amount of punishment when that
engine is running.
If you think about it the combustion phase of a pulsejets operation accounts for less than
50% of the operating cycle. That means, in order to produce (say) 50lbs of thrust, the engine
actually as to create a power-pulse of over 100lbs. When running, that 100lbs of force is
transferred directly to the engine itself and if its made from thin rolled metal, that places an
awfully large amount of stress on certain areas.
Not only is a pulsejet exposed to high levels of vibration and constantly changing tensile and
compressive stresses but it also undergoes a huge and constant amount of thermal cycling.
The end result of this is that it becomes very difficult to design and build large pulsejet engines
that will hang together for any significant amount of time.
In the case of designs such as the Lockwood, the whole problem of metal fatigue is further
aggravated by the difficulties associated with mounting such an oddly shaped engine. This
often means that parts of the engine are left largely unsupported and thus suffer from even
greater levels of vibration/fatigue than might be encountered in other designs.
The critical point for fatigue failure with a valveless pulsejet is the area between 1/3 and 2/3
the length of the tailpipe cone. If you place a weld in this area (which is often unavoidable)
then you really need to keep a close eye on it.
It is very likely that, no matter how carefully you make that weld, cracks will appear around it,
especially if youre using stainless steel.
Ive tried numerous methods for reducing the tendency to crack in this area with varying levels
of success but have come to the conclusion that using thicker material than you might think
necessary is about the only way to reduce the problem.
I tried butt-welding, overlap welding and flanged welds but they all eventually developed
cracks when using a thickness of material that, in all other respects, appears more than
adequate.
Mild steel is far less prone to cracking than stainless steel but it is also much weaker and
therefore needs to be much heavier/thicker if youre to avoid implosions. It also suffers from
rapid oxidation when used in a pulsejet, which means your engine will turn to dust/rust in a
fairly short space of time if plain steel is used.
I have found however, that the use of high-temperature paint of the kind used on automotive
exhaust systems (VHT is just one brandname) work reasonably well on the cooler sections of a
mild-steel engine. This paint can reduce the tendency for the outside of the engine to rust but
it will burn off the really hot sections.
Page 72
Page 73
Page 74
Page 75
Here are the COTEs for some common materials which might be used to build pulsejet
engines (expressed in inches per degree Celsius).
Austinetic (300 series) stainless steel:
Ferritic (400 series) stainless steel:
Martensitic (400 series) stainless steel:
Mild steel (non-carbon):
1.8x10-5
1.1x10-5
1.2x10-5
1.5x10-5
Page 76
Page 77
Page 78
First, cut and bend your cathode plate (aluminum or lead sheet) so that it runs around the
inside edge of your plastic container.
To get an even and all-over layer of anodizing, you need to have your item surrounded by
the cathode plate.
Place the item to be anodized into the
container and make sure that plenty of space
(at least a couple of inches) remains between it
and the cathode plate. This is to make sure
that you dont accidentally touch the two
together and produce a dangerous shortcircuit.
The amount of acid solution you need to mix
up depends pretty much on the size of the
object youre planning to anodize and the
volume of your plastic container.
To avoid having a bald-patch on the bottom
surface, you need to suspend the item to be
anodized in the acid solution so that its not touching the bottom of the container so allow
extra liquid for this.
Dont forget however, that when you lower your item into the solution, the level will rise. If
you are planning to anodize a larger item, the level may rise significantly so factor this in so as
to ensure you dont overflow the container.
Workpiece Preparation
It cant be emphasized just how important it is that the workpiece is scrupulously clean prior to
anodizing.
Any grease, oil or fingerprints will be magnified by the process and produce unsightly
blemishes in the final finish.
To this end, the following steps are useful in ensuring the cleanliness of the workpiece:
1. wash the workpiece in a weak solution of detergent in hot water
2. rinse thoroughly with hot water as any detergent residue will also cause problems.
3. Dip the workpiece into a warm (120 deg F) bath of 5% sodium hydroxide (lye) solution for
about one minute. This will remove any remaining oil or grease and provide a very
consistent surface.
4. Rinse thoroughly with hot water as in step 2 (above)
I find that wearing a pair of cheap latex or nitride gloves when performing the above steps
allows the workpiece to be held without leaving further fingerprints on the cleaned surface.
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 79
Its also advisable in light of the fact that the sodium hydroxide solution is extremely corrosive
to your skin.
Performing The Anodizing
Having set up your anodizing tank and prepared your workpiece, the item to be anodized is
lowered into the acid so that it is completely immersed.
It is then connected to the positive side of
your battery or power supply.
The aluminum cathode plate is connected to
the negative side.
Within a minute or so you should see a steady
stream of bubbles rising from the workpiece
if not, you have a problem.
The most common reason that the workpiece fails to bubble is because the electrical
connection to it is inadequate.
Once the anodizing process is underway you can go and read a book for 20-60 minutes,
depending on the size of your item and the depth of anodizing required.
You can briefly remove the workpiece from the tank from time to time to see how the process
is going. Depending on the alloy involved, it will turn a dull gray or very light yellow color as
the oxide layer forms on the surface.
Using the anodizing setup described above, most workpieces will have a health layer of oxide
on them within 60 minutes of processing at which stage they can be removed and rinsed
thoroughly in COLD water.
It is important that you continue to avoid direct contact with the surface or contamination
with any form of dirt, oil or grease.
Dying the Workpiece
One of the great things about anodizing is that it not only creates a tough, hard layer that
protects the metal from wear but it also allows you to impart a color to it.
The reason you can dye a piece of anodized aluminum is because the oxide layer formed
during the process is quite porous. The millions of tiny oxide crystals act like a sponge and
soak up any dye that has a fine particle structure.
Of course the dying step is optional and if youd like to simply retain the gray color of plain
anodized aluminum you can move right on to the Fixing stage.
The choice of dye is critical to successfully imparting a nice rich color to the anodized layer.
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 80
Ive had great results from the Dylon range of cold water dyes. These are the little plastic pots
with an aluminum lid that can be bought from most fabric stores. Theyre dirt cheap and one
little container produces enough dye to last a very long time.
So far, Ive tried the gold, red and blue colors with good results but others have reported that
the greens also work well.
To dye your workpiece you should remove it from the anodizing tank, rinse well in COLD
water (it is important that the water is not warm or hot) and then imerse it in the dye solution.
I mix one little pot of Dylon to almost a pint of water (500ml) and this concentration works
fine.
Leave it in the dye for about 10 minutes or so to allow the color to get deep into the crystaline
structure of the oxide layer.
Fixing the Anodizing
This is a critical step that physically and chemically changes the structure of the oxide layer
produced by the anodizing process. If you have dyed your workpiece, it effectively locks the
dye in place so it wont leach out.
To perform the fixing you need to hold the anodized (and optionally dyed) workpiece over a
source of steam for at least 10 minutes.
I find that a pot of vigorously boiling water on the stove works fine.
Rotate the work so that the steam comes into contact with all the anodized surfaces.
Its normal for some of the dye to leach out at this stage and color turn the boiling water but
most of it will stay in place.
After 10 minutes of steaming, the workpiece can
be immersed in the boiling water to finish the
job. Leave it boiling for another 10 minutes.
Once youve removed the item from the boiling
water the anodizing is complete.
Adding Luster
You will notice that your newly anodized (and
optionally dyed) piece of aluminum probably
looks quite dull when it dries. This is normal.
The anodizing itself produces a rough surface
that imparts a matte finish rather than a shiny
one.
Page 81
To make the surface shine and add luster all you have to do is either rub in some oil or polish
of some kind.
With some polishes you may get a small amount of the dye coming off on the polishing cloth
but its nothing to worry about.
The result should be a nice shiny workpiece with a deep luster.
Hard Anodizing
The anodizing process described here is often referred to as decorative anodizing because
the thickness of the layer produced is quite low (about 0.0001 to 0.0005 inches) and therefore
only provides a limited amount of protection to the underlying metal.
Another process known as hard anodizing can produce layers of up to 0.005 inches which
are extremely hard and protective.
Performing hard anodizing is a little more complex than the above process however and
involves the use of a chilled acid solution (not necessarily sulfuric) and much higher
voltages/currents.
While it is possible to perform hard anodizing in a home workshop, there are safety issues
involved since the amount of explosive gas produced and the risk of electrical shock are far
higher.
For most purposes, the simple anodizing process described here will provide more than
enough protection.
Page 82
Page 83
Preparation
Let me say right now that preparation is everything. If you skip on this step then you will end
up regretting it later.
The metal from which your reed valve will be etched must be absolutely clean with no traces
of rust or grease as these will cause the paint to lift and allow etching to occur in all the wrong
places.
Its also important that the metal is slightly roughened so that the paint can adhere properly. A
perfectly polished service will give the paint nothing to hold on to and it will come off in big
flakes.
For absolutely the best results you should scrub the reed valve material with a soapimpregnated wire-wool pad. This will remove all traces of grease and (if your arms are up to it)
any rust spots.
Now rinse in very hot water, taking care to hold the metal only by the edges oily fingerprints
will ruin your hard work.
You can now give the metal an acid-etch if you have some dilute sulfuric acid available. This is
done by dipping the bare metal into a very dilute solution (battery acid can be diluted by 4
parts of water). Place the metal in the solution and you should see small bubbles start forming.
Lift it out at regular intervals and when its turned a dull gray color you can rinse it under hot
running water again.
This acid-etch will provide the best surface for paint to adhere to but if you dont have any
sulfuric acid then dont worry you can give both sides of the metal a light sanding with 1200
grade wet-and-dry sandpaper. This will provide a similar surface roughness to help paint
adhesion.
Painting
The type of paint and the manner in which its applied will also be a critical factor in the
success of the etching operation.
Dont use a cheap spray-can enamel it probably
wont stick well enough, even if youve roughened
the surface.
Whats needed is an automotive undercoat. These
paints are designed to be sprayed directly onto
bare metal and can be obtained in spray-can form
from your local paint store or auto accessories
outlet. If you can, use white undercoat it makes
the job of getting a nice even coat much easier
than when using the traditional gray.
Make sure you get an even and thorough coating
of paint on the metal. I actually find it easier to lay the metal on a sheet of newspaper and
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 84
spray it while its flat. This avoids creating paint runs if you over-do it slightly. Of course it
means that you have to wait for one side to dry before you can turn it over and do the other
but automotive primers tend to be very fast-drying anyway.
Once the first coat is dry, give it another thorough all-over coat.
Dont be tempted to make do with a single coat. Even though it may look as if youve covered
all the metal, experience has shown that there will probably be some very tiny pinholes that
will cause similar holes to appear in your reed valve. A second coat is good insurance against
this type of thing happening.
Another reason you want at least two coats is because as you near the end of the etching
process, its only the paint that will hold everything together. Insufficient paint means that the
valve will start breaking away from the rest of the metal prematurely and this can cause the
paint to rip away from a surface you dont want etched with disastrous results.
Let the paint dry at least overnight if you can. Even though these paints are fast-drying, the
very bottom layer tends to remain slightly plastic for several hours and this can cause the lines
you scribe later to close-over.
Marking Out
Now that you have a nice piece of reed valve
material, totally covered in a good solid layer of
paint, you need to scribe the lines that represent
the outline of your reed valve.
NOTE: You only scribe one side! The undisturbed
layer of paint on the back-side of the plate will
hold everything together as the metal under the
scribed lines is etched away.
You can draw and scribe the pattern of your
reed valve directly onto the piece of metal
youve prepared but its a better idea to make a
template that you can trace around.
The reasons for this are obvious: If you make a mistake while
drawing the pattern onto your painted material then your work
to date will have been wasted.
Ive made a template from 1mm (0.040) stainless steel and I
simply press this against the prepared reed valve material and
scribe around the edges with a sharp modeling knife. Dont
forget to also scribe the hole in the middle!
If you have an existing reed valve in good condition then you
can use that as the template for scribing your pattern.
Page 85
When youve finished scribing, the shiny steel underneath the paint should be visible at the
bottom of the scribe lines.
Check to make sure that all your lines join where they should a line that doesnt quite join up
will leave a bridge of metal that will make complicate removal of the valve from the sheet of
prepared metal.
Etching
Youll need a plastic or glass bowl or container that is
large enough to fully submerse your valve material
while its stood on edge. As you can see here, Ive
used an old yogurt container but you can grab your
mother or wifes Tupperware if shes not looking and
it would do just as well.
Now mix up a solution of common table salt and
water. About a tablespoon per pint will do the trick
the strength of the solution isnt that critical. Youll
need enough to fill your container to the desired level.
Hint: the salt will dissolve more easily if you use warm water.
Now find yourself a piece of stainless (preferred) or
regular steel that will act as a cathode plate in the
solution. It should be about the same area as your
blank sheet of reed valve material although, once
again, this isnt too critical.
Next, youll need a source of 6-12V DC. This can be a
lead acid car or motorcycle battery or, if you have one,
a variable voltage/current power supply.
Connect that plate to the NEGATIVE terminal of your battery or power supply and place it
on once side of your container, immersed in the salt solution.
Place your painted and scribed piece of reed valve
material in the salt solution on the other side of your
container making sure that the scribed side faces the
cathode plate.
Make absolutely sure that the two pieces of metal can not
accidentally touch together if they move. One good way
to do this is to place a sponge in the middle. This will
absorb the salt solution and allow the current to flow but
stops the two plates from meeting.
Connect the reed valve material to the POSITIVE terminal of your power supply. You may
want to include a resistor (8 ohms is about optimum) in this lead to limit the current flow if
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 86
youre using a small container as I have here. If you dont have an 10 watt, 8 ohm resistor, you
can use a 10W-20W 12V light bulb instead.
Once you connect things up, you should see bubbles begin to rise from the cathode plate as in
the picture.
At this stage the salt solution will still be clear.
Depending on a number of factors, it may take
between 10 minutes and an hour to etch your
valve. Once the process gets underway, a
rather awful looking green or brown sludge will
begin to form on top of the solution. This is
the iron that has been removed from the
scribed lines.
Things will go more quickly and the results will
be better if you give the reed valve plate a bit
of a shake now and then. This dislodges the
crud that forms on the scribed lines so that a
fresh salt solution can reach the bare metal and continue etching.
If you remove the plate from the solution youll see that the formerly shiny metal under the
scribed lines has turned black.
Eventually the scribed lines will etch right through and when you
remove the plate from the solution youll see the paint on the
back surface exposed.
If you hold the plate up to a lamp at this stage you can see exactly
where the etching is complete because the light will shine right
through as in this picture.
Post-etching Steps
Once you get to this stage you can disconnect all
the wires and carefully push the reed valve out of
the plate. There will probably still be some areas
where the etching is not quite complete but the
metal at these points will now be so thin that it
will break away very easily.
Dont worry if the edges seem a little ragged this
is normal.
Now wash off the paint with suitable thinners.
Another benefit of the automotive primer is that
it washes off very easily with lacquer thinners.
Page 87
Now youll have a new valve but chances are that the edges will still be ragged as mentioned
above.
In order to avoid premature cracking of the valve it pays to file or sand those ragged edges to
make them smooth(er).
In theory, you can further reduce the risk of cracking by putting the valve in your oven at
about 200 deg F for an hour or so. What this will do is bake out any hydrogen that might have
entered the structure of the reed valve material as a result of the etching. Hydrogen in the
molecular structure causes what is known as hydrogen embrittlement and that makes steel
far more prone to cracking. For what its worth I dont bother. Lets face it the valves are
going to get hot enough anyway once you fire up your engine.
Page 88
To see just how this works, look at the diagram above which represents two containers filled
with pressurized gas. The first box is sealed so the pressure inside is perfectly balanced and
theres an equal force pushing on all interior surfaces. The result of this is that everything is
balanced and no thrust is created.
If, as in the second diagram, we suddenly remove one side of the box then suddenly the
pressure has nothing to push against. Consider this to be the open tailpipe of a pulsejet.
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 89
However, there is still pressure acting on the other interior surfaces of the box but now we
have an imbalance.
The pressure pushing the box upwards is still balanced by the pressure pushing it downwards
but the pressure pushing the box to the left is no longer balanced by the pressure pushing it to
the right.
As a result, the box in the second diagram will be pushed to the left by a force equal (but
opposite in direction) to the force with which the compressed gas blows out through the large
hole.
We can actually calculate the thrust that will be produced by summing the force vectors.
If we assume that the box is a one-foot cube and that the pressure inside is 10psi then we can
see that if one side was suddenly removed thered be 1 square foot (144 square inches) of
unbalanced force pushing on the left hand side of the box. That would produce a thrust equal
to 1,440 lbs.
Of course this simple calculation assumes that the pressure inside the box will remain at 10psi
even when the side is removed.
If, instead of knocking the whole right-hand side off the box, we simply cut a 1 square inch
hole then just 10lbs of thrust would be generated. The other 1,430 lbs would be pressing
against the part of the side that was still intact and balancing the force pushing on the left-hand
side.
This simple calculation validates Tharrats 2.2lbs of thrust per sq in of cross-sectional area
constant we mentioned in an earlier chapter.
Tests conducted on the Argus V1 engine
showed an average pressure at the end of
the tailpipe of around 2.2-2.6 lbs per
square inch.
This figure represents the average value of a pressure wave that fluctuated from a maximum
peak of +6.2 psi achieved during the combustion phase, to a minimum of 4.46 psi produced
during the intake phase.
Page 90
Page 91
Page 92
sucks the fuel through a ring of small holes. When the fuel hits this fast-moving airflow it
breaks up into droplets.
Without the Bernoulli effect a Dynajet wouldnt run because it couldnt suck any fuel into the
engine.
Theres another area where some believe that the Bernoulli effect plays an important role in
pulsejet operation.
Take a look at the shape of the average petal-valved engine again. Note that it has a larger
diameter section at the front and a smaller diameter tailpipe. These two sections are joined by
a cone.
Now imagine what happens when the hot exhaust gases are drawn back into the front section
by the partial vacuum left after combustion. While in the tailpipe, those gases will be travelling
relatively quickly so theyll have a low pressure.
As they pass through the cone, into the larger diameter front section of the engine they will
slow down and in doing so, their pressure will (thanks to Mr Bernoulli) increase. One of the
things we want for efficient combustion is as much compression of the air/fuel charge as
possible.
Personally I dont believe that this particular effect has any real bearing on a pulsejets
operation an assertion supported by research that shows pulsejets with a completely straight
pipe are capable of producing just as much thrust as those which have an enlarged front
section.
Others have pointed out that the Argus engine has a diffuser section immediately after the
valve-grid. The claim is that this diffuser is a device that acts like a divergent cone and
therefore increases the pressure of the incoming air/fuel mixture by slowing it down.
Perhaps it does have this effect, but my own experiments with intake diffusers indicates that
their main benefit is that of forcing the air/fuel mixture through a narrow section so that
mixing is more thorough and, as a result, combustion is more rapid.
I also believe that the Argus diffuser also reduces the valve grids exposure to hot combustion
gases by effectively choking their flow towards the front of the engine.
One only has to look at how the Dynajet (which has absolutely no internal diffuser) produces
almost an identical power/volume output as the Argus (with its internal diffuser) to realise that
the effect of such a device on an engines power output is minimal at best.
Page 93
Page 94
Plans
This chapter of the book includes a number
of plans for various engines, including the 55lbs thrust enhanced Lockwood Valveless
engine that currently resides on my kart and
which featured in the popular TV series
Scrapheap Challenge.
Although based on similar designs, this
particular version has a flared intake cone and
slightly different combustion chamber
dimensions both of which help to assist in
throttling and easy starting.
This engine should be built from material that is at least 0.7mm in thickness and, if weight isnt
too much of an issue, you might find it worthwhile going up to 1.2 or even 1.5mm material.
Although thicker material will cost and weigh more, and is harder to form, the result will be a
more durable engine that is less likely to suffer from cracking.
This plan is included as a separate PDF file (55lbslh.pdf) and contains all the dimensions you
need to build your own.
One detail often missing in other Lockwood plans you might find on the internet is how the
fuel-injection system works.
Page 95
Page 96
This simple engine wont produce a whole lot of thrust, but its a great way to get your hands
on a real working engine for probably less than $20 in materials.
Other plans will be posted to my website as they become available. You should check the
subscriber section regularly for updates using the ID and password that will have been
supplied to you when you purchased this disk.
Page 97
Wacky Ideas
I regularly get email from people who want to know if their idea will work when applied to
pulsejets. Here are some of the most common:
1. Water Injection
Full-sized turbojets can gain significant amounts of power by the use of water-injection. This
works in two ways.
If water is injected into the intake of the engine, its evaporation cools the incoming air, this
increasing its density. Since the power of almost all engines depends on the difference
between the minimum and maximum temperatures involved, cooling the incoming air will
raise power.
This method of water-injection was actually used in some WW2 aircraft piston-engines where a
mixture of water and methanol was used.
The second way to use water injection is to squirt water into the combustion-chamber where
the extremely high temperatures will cause that water to flash into steam increasing the
pressure in the chamber. One modern jet aircraft that uses this technique is the Hawker
Harrier AV8 jump-jet. The use of water-injection is essential when this plane needs to
perform a vertical take-off or landing while heavily laden with weapons or other external
stores. Unfortunately, since water itself is very heavy, these planes only have sufficient water
on board to allow a minute or two of vertical flight.
But back to pulsejets.
In theory, water injection should provide some additional power when used in a pulsejet but I
have yet to try this in practice.
A big problem however, is the additional weight and complexity that the water, plumbing and
pump would add to an engine that has simplicity as one of its few virtues.
In reality, it might be more practical to use a pulsejet as a flash-steam boiler by wrapping it in
copper pipe through which water is pumped. That water would be flashed into steam by the
intense heat of combustion then the steam could drive a turbine or piston.
2. Adding a turbine to the pulsejet
Although this is an idea that was first contemplated many years ago, my own experiments
indicate that it doesnt work very well at all.
The problem is that pulsejets suck and blow through the same pipe. That means our turbine
will be subjected to alternate forces that first try to rotate it in one direction then in another.
Since efficient turbines tend to be rather delicate devices, pounding them hundreds of times
per minute with pulses of hot gas is not likely to create a very reliable machine.
Page 98
When I placed a small fan in the exhaust of a pulsejet I was surprised at just how little
inclination it had to spin even though the engine was putting out good power. Bringing it
closer to the tailpipe actually reduced the spinning as the effect of the suck phase became
more pronounced.
3. Running a pulsejet on hydrogen
They keep telling us that hydrogen is the fuel of the future, mainly because when it burns all
you get is heat and water (usually in the form of steam).
While thats true, hydrogen does not make a good fuel for pulsejets for several reasons:
Firstly, hydrogen is an incredible gas insomuch as it has an extraordinarily wide stoichiometric
range. In simple terms, that means it will burn equally well when theres just a little oxygen as
when theres a whole lot of oxygen.
If we compare hydrogen to regular gasoline we see that in order for gasoline to burn it must
represent no less than 1% and no more than 7.8% of an air/fuel mixture. Any less and theres
not enough fuel to form a flammable vapor, any more and theres not enough oxygen to
support combustion.
Hydrogen however, will burn happily when it constitutes anywhere from 4% to 75% of an
air/fuel mixture.
This produces an undesirable effect when used in a conventional pulsejet engine.
As youve probably already figured out a pulsejet does not burn its fuel continuously but in
short bursts. The fuel wont ignite unless just the right amount of air is mixed with it. During
the operating cycle of a conventional pulsejet there are times when we have air, fuel and
flames in close proximity to each other but the air/fuel mixture seems to ignite at just the
right time.
One of the reasons for this is that the comparatively narrow stoichiometric range of most
hydrocarbon fuels suppresses premature ignition the fuel wont ignite until theres just
enough air in the engine.
In the USA, NASA attempted to run a popular model airplane pulsejet (the Dynajet) using
hydrogen as a fuel and they failed to get it to pulse. The hydrogen seemed to burn
continuously because of its wide stoichiometric range.
There are numerous other problems that preclude hydrogen from being a viable pulsejet (or
any engine) fuel for now.
It is extremely difficult to store hydrogen safely. In order to store enough of it to be useful it
has to be either compressed to incredibly high pressures, or chemically bound in a matrix of
highly reactive materials such as metal hydrides.
In the former case there are obvious risks should a pressure vessel fail and the weight of such
containers detracts from the overall efficiency of a hydrogen-powered engine package.
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 99
In the latter case, the chemical storage of hydrogen involves the use of very expensive and
dangerous chemicals that react violently with common substances such as water.
4. Fitting an afterburner
Sorry, conventional afterburners wont work on pulsejets for several reasons.
Firstly, they are designed for turbojets where the gas-flow from the engines exhaust is a
constant flow. Unfortunately pulsejets create a flow that actually reverses briefly during the
intake phase of the engines operation.
However, always keen to try the impossible, I added an afterburner to my jetkart. Check out
the next chapter on pulsejet afterburners to see how that turned out.
5. Building a really small pulsejet
Its sad but true that the smaller you make a pulsejet, the more difficult it will be to start and
the less power it will produce.
And dont think that by halving the size of a pulsejet you halve the power because thats not
so. Halving the size of a pulsejet will actually reduce the power by a factor of four. Yes, thats
right, all else being equal, half the size means just a quarter the power.
Another factor that adversely affects small pulsejets is their very low Reynolds numbers (see
the chapter on the Reynolds Effect). As pulsejets become smaller, the air appears to become
thicker until it becomes just too thick to be sucked and pushed through the engine given the
small amount of power available to do so.
The smallest practical pulsejet Ive been able to get running on regular fuels was about 14
inches in length and inches in diameter.
Page 100
6. Pulsejet-powered helicopters
I shudder everytime I hear of someone who is thinking of building a helicopter powered by a
pulsejet. Trust me when I say that this is not a good idea if you value your life.
There have only been a very few such craft ever built and, without exception, they were never
flown for any length of time or made into commercially viable products. Valved pulsejets are
simply not reliable enough to bet your life on and valveless engines are difficult to design in
such a way that they are compact and streamlined enough to fit to a helicopters rotor-tips.
Lockwood-Hiller did experiment with special valveless engines designed to be built into the
blades of a helicopter but this project was dropped ask yourself why.
Page 101
Afterburning Augmentors
In theory, you cant fit a working afterburner to a pulsejet for several reasons:
1. An afterburner is really just a specialized ramjet engine, and ramjets only work when the air
flowing into them exceeds a speed of around 350mph (560kph). Although the gasses
ejected from the tailpipe of a pulsejet regularly exceed this velocity by a factor of two or
more, they also slow to zero and actually reverse direction, being sucked back into the
tailpipe, once per engine-cycle. This would mean that most of the time, a pulsejet
afterburner would be doing nothing but getting in the way.
2. An afterburner is an air-breathing engine and requires that the gases that enter its intake
contain enough oxygen to support the combustion of the fuel injected into it. In the case
of a gas-turbine engine, this oxygen is provided by the large percentage of air which passes
straight through the engine without being involved in the combustion process. In the case
of a pulsejet however, there is absolutely no oxygen left in the exhaust gases so theres
nothing to support the combustion of additional fuel injected into an afterburner
So it would appear that theres simply no way to add an afterburner to a pulsejet, right?
It could also be argued that theres no point in adding a fuel-guzzling afterburner to a pulsejet
because an augmentor will provide the same effect (a thrust increase) far more easily and with
the added bonus of not increasing fuel consumption
But what if we injected fuel into the augmentor and tried to produce a device that performed
both roles?
Since an augmentor works by drawing in fresh, cold, oxygen-rich air and mixing it with the hot
exhaust gases, it should be possible to inject fuel and burn it in the augmentor cone itself.
Copyright 2004 Bruce Simpson. http://aardvark.co.nz/pjet
Page 102
To test this out, I added an afterburning augmentor to the 55-lbs-thrust Lockwood valveless
pulsejet on my gokart.
As youll see by the videos on this disk, this afterburner certainly produces some impressive
visual effects, creating a long tail of yellow flame out the back of the engine but does it
increase the thrust at all?
Well the first clue is in the color of that flame.
A yellow flame indicates poor
combustion, generally resulting
from inadequate oxygen being
available for complete
combustion. An obvious
solution would be to reduce the
amount of fuel being injected so
as to lean-out the mixture.
Unfortunately, due to the very inconsistent airflow through the augmentor, it is not possible to
reduce the flow much before the fire goes out completely.
I tried a range of different flame-holders (devices designed to protect the flame from being
blown out) but found that the wild variations in the speed of the gases through the augmentor
made it impossible to get a consistent lean-burn.
Undeterred, I measured the thrust being developed as follows:
plain (unaugmented) Lockwood engine
augmented engine
augmented with afterburner
25.0Kg
35.5Kg
36.0Kg
57lbs
80lbs
81lbs
Clearly in this case, adding fuel to the augmentor makes no practical difference in terms of
thrust generated.
Although I could claim these results prove my claim that you cant add an afterburner to a
pulsejet, it must be acknowledged that the design of a good augmentor is far from the design
of a good ramjet. Experimentation with the shape and design of an afterburning augmentor
may result in some improvement, and possible a small amount of thrust Increase.
However, wouldnt it just be a whole lot easier to build a slightly larger engine in the first
place?
Page 103
Page 104
Tharrat
Another of the leading lights in pulsejet design is Tharrat and his short but extremely
enlightening paper The Propulsive Duct.
In just a few short pages, Tharratt concisely lays out the basic principles of pulsejet operation
and offers some simple formulas for calculating elementary propulsive ducts of almost any
size.
Kentfield
Through is work at the University of Calgary, Kentfield has offered some interesting insights
in to variations on the basic valveless engine design.
His four-intake abreviated Lockwood derivative claims superior fuel efficiency and a more
compact form factor than the engine that sprung from the Hiller workshops in the 1960s.
I know of several versions of this design that have been built and appear to work as intended.
Schmidt
Ive already dedicated an entire chapter of this book to the work performed by Schmidt since it
really was pivotal in the single most obvious use of the propulsive pulsejet engine the V1, but
this chapter would not be complete without a mention of his work.
Lockwood
To be honest, Ray Lockwood didnt really come up with
much in the way of new ideas during his time at Hiller in
the 1960s. However, he did put much existing theory to
good use in the design and refinement of his well-known
horse-shoe-shaped valveless engine.
His designs are perhaps the easiest to build an operate of
all the valveless engine designs and for that reason they
deserve recognition. Lockwood also put quite a bit of
effort into the design and analysis of augmentors, which
became a key element of his lift engines.
The lift engines were heavily augmented and designed
primarily to create high levels of static thrust suitable for
vertical take-off vehicles and such things as lifting military
equipment into a hover so that it could be easily moved.
Unfortunately none of this turned out to be practical.
Page 105
Page 106