Professional Documents
Culture Documents
Optimisation 3G Huawei PDF
Optimisation 3G Huawei PDF
OWJ200203 WCDMA
Access Problems Analysis
ISSUE 1.0
www.huawei.com
Page 1
Page 2
Page 3
Page 4
Page 5
UE does not
transmit RRC Connection Request message after dialing
by UE
UE receives RRC Connection Reject message
UE does not receive measurement control message after
Page 6
proceeding message
UE does not transmit RB setup complete message after
setup message
UE does not transmit Connect Acknowledge message after
Page 7
Page 8
Page 9
Call Fail?
Y
Calling failure?
Received
paging
Paging
problems
Y
Y
RRC
connection
setup failure?
Page 10
Is ciphering or
authentication
failure?
Ciphering or
authentication
problems
RAB
failure?
setup
to
RAB or RB
setup problems
Due
handover
Abnormal problems
Page 11
Page 12
Page 13
UE
receive
page N
Power too
low ?
Cell
reselection
problem ?
Equipment abnormal
problem
Adjust power
according
coverage
to
Optimize cell
reselect parameters
Abnormal
problem
Page 14
RNC has received the paging message but does not transmit paging
message through Uu interface. The reasons could be:
Capacity of paging channel is not enough
Abnormal problem could happen in equipment.
Power allocation PRACH or PICH are too low
Page 15
Page 16
Page 17
Page 18
UE
abnormal
problem
Other problem
10
Page 19
Does UE receive
RRC connection
setup
Does cell
reselection
happen?
Optimize cell
reselection parameters
Does UE transmit
RRC
connection
setup complete
Page 20
RACH
Usually, it could be the problem on RACH if the RNC does not receive
RRC Connection Request message. Meanwhile, the Ec/Io of CPICH is
normal
The cell reselection parameters
The improper parameters setting could result in that UE can not stay in
the best cell to initiate the access procedure
Lower power allocation for initial transmission power of downlink DPCH
The insufficient power of DPCH can cause the out of synchronization.
Uplink initial transmission power
The initial transmission power of PRACH
The initial transmission power of uplink DPCH
11
Page 21
UE
Serving
RNC
RRC
Allocate RNTI
Select L1 and L2
parameters
2. Radio Link Setup Request
NBAP
NBAP
Start RX
description
3. Radio Link Setup Response
NBAP
NBAP
DCH - FP
6. Uplink Synchronisation
DCH - FP
DCH - FP
DCH - FP
Start TX
description
7. CCCH : RRC Connection Set up
RRC
RRC
8. Radio Link Restore Indication
NBAP
NBAP
9. DCCH : RRC Connection Setup Complete
RRC
RRC
Page 22
12
Page 23
formulas:
Page 24
Analysis
access
index about cell
Check system
alarm
Solve problem of
equipment abnormal
RRC
setup
success rate is
too low
Solve problem of
RRC setup failure
13
Page 25
RAB setup
success rate is
too low
Solve problem of
RAB
setup
failure
RB
setup
success rate is
too low
Solve problem of
RB setup failure
paging
success rate
is too low
Solve problem of
paging failure
Y
over
Page 26
14
Page 27
Page 28
Project parameters
Project parameters main include antenna azimuth, antenna
coverage condition.
15
Page 29
Page 30
Cell parameters
Physical channels parameters
Transmission power of FACH, PCH and PICH
16
Page 31
Cell parameters
Cell reselection parameters
Qhyst:
The duration time that target cell signal quality is better than
current camp cell is longer than Treselections. The cell will
be selected to the camping cell.
The parameter is use to avoid ping-pang cell reselection
Page 32
Cell parameters
Cell reselection parameters
Sintrasearch
17
Page 33
Page 34
18
Page 35
Page 36
19
Page 37
but RRC establishment success rate is about 94% from traffic statistic
After analysis, the RRC Connection Request retransmission is the result of
following reasons:
The area with good downlink coverage
Other reasons
Page 38
20
Page 39
Page 40
21
Page 41
Thank You
www.huawei.com
22
Page 42