Professional Documents
Culture Documents
Grid Interconnection of Renewable Energy Sources With PQ Improvement Features at The Distribution Level
Grid Interconnection of Renewable Energy Sources With PQ Improvement Features at The Distribution Level
Grid Interconnection of Renewable Energy Sources With PQ Improvement Features at The Distribution Level
(Affiliated to JNTUH)
Abstract
The Transient response of the Shunt Active filters (SAF) is very important while compensating
rapidly varying unbalanced and nonlinear loads.
The proper operation of SAF requires variation of the DC link voltage within the prescribed limits.
Conventionally, a proportional-integral (PI) controller is used to maintain the dc-link voltage to the
reference value
However, the transient response of the conventional PI dc-link voltage controller is slow.
In this paper, a fast acting dc-link voltage controller based on the energy of the dc-link capacitor is
proposed and proposed shunt controller method by using SVPWM Technique Mathematical
equations are given to compute the gains of the conventional controller based on the fast-acting dclink controllers to achieve similar fast transient response.
CONTENTS
INTRODUCTION
POWER QUALITY
SVPWM TECHNIQUE
SIMULATION RESULTS
INTRODUCTION
With increasing problems of global warming and the depletion of fossil fuel reserves,
many are looking at sustainable energy solutions such as RES
Other than hydro power, wind and solar energy holds the most potential to meet our
energy demands
wind energy is capable of supplying large amounts of power but its presence is highly
unpredictable
Similarly, solar energy is present throughout the day but the solar irradiation levels
vary due to sun intensity and unpredictable shadows cast by clouds, trees etc
The common inherent drawback of wind and photovoltaic systems are their
intermittent natures that make them unreliable.
The integration of renewable energy sources and energy-storage systems has been
one of the new trends in power-electronic technology.
Such hybrid systems, focusing on providing sustainable power to their loads, do not
care much about the quality or flexibility of power delivered to the grid.
Photovoltaic Effect
Photovoltaic (PV) is a method of generating electrical power by converting solar
radiation into direct current electricity using semiconductors that exhibit the
photovoltaic effect
solar panels comprising a number of cells containing a photovoltaic material.
Assemblies of cells are used to make solar modules, also known as solar panels.
Photovoltaic cell produces only about one-half volt of electricity, cells are often
mounted together in groups called modules
When light energy strikes the solar cell, electrons are knocked loose from the atoms
in the semiconductor material.
If electrical conductors are attached to the positive and negative sides, forming an
electrical circuit, the electrons can be captured in the form of an electric current.
Each PV cell converts about 5 to 15 percent of the sunlight that hits it into electrical
current.
POWER QUALITY
Equipment has become less tolerant of voltage quality disturbances, due to less
tolerant of voltage disturbances equipment is incorrect in operation.
Equipment produces more current disturbances than it used to do. Due to these
current distortions harmonics are generated in power system.
Also energy efficient equipment is an important source of power quality.
PURPOSE OF STANDARDIZATION
Almost all countrys has standards defining the margins in which frequency and
voltage are allowed to vary.
Other standards limits
harmonic current and voltage distortion,
voltage fluctuations,
duration of an interruption
These are three reasons for developing power quality standards.
STATCOM
VSC used in adjustable-speed drives, but can also be used to reduce voltage dips.
The VSC is used to either completely replace the voltage or to inject the missing
voltage. The missing voltage is the difference between the nominal voltage and the
actual.
HARMONICS MITIGATE
Harmonic Filters may be used to reduce and in some cases, eliminate harmonics in
power system .
Non-linear loads such as rectifiers, converters, home electronic appliances, and
electric arc furnaces cause harmonics giving rise to extra losses in power equipment
such as transformers, motors and capacitors
Installing filters near the harmonic sources can effectively reduce harmonics.
active filters, based on power electronic converters with high switching frequency,
may be a more attractive solution.
Benefits
Eliminates harmonics
Improved Power Factor
Reduced Transmission Losses
Increased Transmission Capability
Improved Voltage Control
Improved Power Quality
An active shunt filter, which is most widely used to eliminate current harmonics,
reactive power compensation , and balancing unbalanced currents.
It is mainly used at the load end, because current harmonics are injected by
nonlinear loads.
It can also be used as a static VAR generator (STATCOM) in the power system
network for stabilizing and improving the voltage profile
Coordinate Transformation :
A three-phase voltage vector is transformed into a vector in the d-q frame which
represents the vector sum of the three-phase voltage.
The vectors (V1 to V6) divide the plane into six sectors (each sector: 60 degrees)
PWM METHODS
BLOCK DIAGRAM
CONCLUSION
In this paper we have studied and analyzed the operation and performance of SAF.
This proposed model is implemented using Mat lab Simulink software and the
obtained resultant waveforms
The fast acting dc link voltage controller is suggested to ensure the fast transient
response of the compensator.
The effectiveness of the proposed controller over the conventional dc link voltage
controller and SVPWM Technique are established through the digital simulation
studies.
It is observed from these studies that the proposed dc link voltage controller gives
fast transient response under load transients.