Professional Documents
Culture Documents
FormP 2
FormP 2
2. Manufactured for
(Name and address of purchaser)
3. Location of Installation
(Name and address)
4. Type
Boiler No.
Year Built
(HRT, etc.)
(CRN)
(Drawing No.)
5. The chemical and physical properties of all parts meet the requirements of material specifications of the ASME BOILER AND PRESSURE VESSEL
CODE. The design, construction, and workmanship conform to Section I of the ASME Boiler and Pressure Vessel Code
,
(Year)
Addenda to
(Numbers)
Manufacturers Partial Data Reports properly identified and signed by Commissioned Inspectors are attached for the following items of this report:
(Name of part, item number, mfrs. name and identifying stamp)
6. Shells or drums:
(no.)
[thickness (in.)]
[dia (ID)]
(length, inside)
[dia (ID)]
(length, inside)
7. Joints:
[long (seamless, welded)]
8. Heads
(Material Specification No.: Thickness Flat, Dished, Ellipsoidal Radius of Dish)
9. Tubesheet
Tube Holes
(Matl. Spec., Grade, Thickenss)
(Dia)
Dia
Length
(If various, give max & min)
(Straight or Bent)
Gauge
(or thickness)
Size
Total
(O.D. or W x H)
Type
(Plain, Adamson, Ring Reinforced, Corrugated, Combined, or Stayed)
Seams: Type
(Matl. Spec., Grade, Thickness)
(Seamless, Welded)
Size
(Dia. Matl. Spec. Grade, Size Telltale, Net Area)
Pitch
MAWP
psi.
Location
Material
Spec. No.
No. and
Size
Type
Max.
Pitch
Fig. PFT-32
L/l
Dist. Tubes
to Shell
MAWP,
psi
2.
3.
1.
2.
3.
(Matl. Spec., Grade, Size, Material Thickness, MAWP)
(12/97)
This form (E00068) may be obtained from the Order Dept., ASME, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300.
(c) Blowoff
(d) Feed
(No., Size, Type, and Location)
Size
Location
Size
Location
Type
Attachment
(Saddles, Legs, Lugs)
18. MAWP
(Bolted or Welded)
psi Based On
Heating Surface
sq ft
psig
(Total)
lb/hr
21. Remarks
Signed
symbol expires
Name
(Authorized Representative)
(Manufacturer)
at
.
I, the undersigned, holding a valid commission issued by the National Board of Boiler and Pressure Vessel Inspectors and/or the state or province
of
and employed by
have inspected parts of this boiler referred to as data items
and have examined Manufacturers Partial Data Reports for items
and state that, to the best of my knowledge and belief, the manufacturer has
constructed this boiler in accordance with Section I of the ASME BOILER AND PRESSURE VESSEL CODE.
By signing this certificate neither the inspector nor his employer makes any warranty, expressed or implied, concerning the boiler described in
this Manufacturers Data Report. Furthermore, neither the inspector nor his employer shall be liable in any manner for any personal injury or
property damage or a loss of any kind arising from or connected with this inspection.
Date
Signed
Commissions
(Authorized Inspector)
Signed
symbol expires
Name
(Authorized Representative)
(Assembler)
and employed by
have compared statements in this Manufacturers Data Report with the described boiler and state that the parts referred to as data items
, not included in the certificate of shop inspection, have been inspected by me and that to the best of my knowledge and
belief the manufacturer and/or the assembler has constructed and assembled this boiler in accordance with the applicable sections of the ASME
BOILER AND PRESSURE VESSEL CODE. The described boiler was inspected and subjected to a hydrostatic test of
psi.
By signing this certificate neither the inspector nor his employer makes any warranty, expressed or implied, concerning the boiler described in
this Manufacturers Data Report. Furthermore, neither the inspector nor his employer shall be liable in any manner for any personal injury or
property damage or a loss of any kind arising from or connected with this inspection.
Date
Signed
Commissions
(Authorized Inspector)