Professional Documents
Culture Documents
Table G5 Dimensions of Class 2500 Flanged Fittings (Cont'd) : GG NN G GG NN G
Table G5 Dimensions of Class 2500 Flanged Fittings (Cont'd) : GG NN G GG NN G
ASME B16.5-2003
GG
NN
G
GG
NN
G
A
HH A
A
A
H A
A H
tf
FF
MM
t
Flanged Fitting
True Y
Eccentric Reducer
Reducer
90 deg
12
13
14
15
16
17
18
19
20
Nominal
Pipe
Size
Center-toEnd, Elbow,
Tee, Cross,
and True
Y,
HH
[Note (3)]
Center-toEnd, 45 deg
Elbow,
KK
[Note (3)]
Long Centerto-End
Lateral,
LL
[Note (3)]
End-toEnd
Reducer,
NN
[Notes
(2), (3)]
5.19
5.37
6.06
6.87
7.56
...
...
4.00
4.25
4.75
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
5.19
5.19
6.06
6.94
7.62
...
...
4.00
4.31
4.81
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
2
4
1
114
112
8.87
10.00
11.37
13.25
5.75
6.25
7.25
8.50
15.25
17.25
19.75
23.00
5.25
5.75
6.75
7.75
9.50
10.50
11.75
13.50
8.94
10.12
11.50
13.44
5.81
6.38
7.38
8.69
15.31
17.38
19.88
23.19
5.31
5.88
6.88
7.94
...
...
...
...
2
212
3
4
15.62
18.00
20.12
25.00
28.00
10.00
11.50
12.75
16.00
17.75
27.25
31.25
35.25
43.25
49.25
9.25
10.50
11.75
14.75
16.25
15.75
18.00
20.50
25.50
29.00
15.88
18.25
20.44
25.44
28.44
10.25
11.75
13.06
16.44
18.19
27.50
31.50
35.56
43.69
49.69
9.50
10.75
12.06
15.19
16.62
...
...
...
...
...
5
6
8
10
12
GENERAL NOTES:
(a) Dimensions are in inches.
(b) For tolerances, see para. 7.
(c) For facings, see para. 6.4.
(d) For flange bolt holes, see para 6.5 and Table F21 of Annex F.
(e) For spot facing, see para. 6.6
(f) For intersecting centerlines, center-to-contact surface, and center-to-end dimensions of side outlet fittings, see para.
6.2.4.
(g) For center-to-contact surface and center-to-end dimensions of special degree elbows, see para. 6.2.5.
(h) For reinforcement of certain fittings, see para. 6.1.
(i) For drains, see para. 6.12.
NOTES:
(1) For center-to-contact surface and center-to-end dimensions of reducing fittings, see para. 6.2.3.
(2) For contact surface-to-contact surface and end-to-end dimensions of reducers and eccentric reducers, see para. 6.2.3.
(3) These dimensions apply to straight sizes only (See paras. 6.2.3 and 6.4.2.2). For the center-to-end dimensions of reducing fittings or end-to-end dimensions of reducers, use center-to-flange edge or flange edge-to-flange edge dimensions
for largest opening, and add the proper height to provide for ring joint groove applying to each flange. See Table F5 of
Annex F for ring joint facing dimensions.
213