Professional Documents
Culture Documents
Daewoo Training Manual Trouble Shooting CN 001 CCP 185 385 785
Daewoo Training Manual Trouble Shooting CN 001 CCP 185 385 785
PRODUCT : COLOR - TV
Jun . 2002
Table of contents
Chapter 1. TV Standards
1. Introduction---------------------------------------------------- 2
2. Trend of Trouble---------------------------------------------
1. CN-001N CHASSIS----------------------------------------- 11
2. CP-185 CHASSIS------------------------------------------- 17
3. CP-385 CHASSIS------------------------------------------- 22
4. CP-785 CHASSIS------------------------------------------- 27
Chapter 1. TV Standards
1. Introduction
The first, color television system to be used for a public broadcast service was the
CBS(Columbia Broadcasting System) field sequential system which was adopted in
the United States in 1951.
The CBS system was subsequently replaced by the NTSC(National Television
System Committee) system which transmits all three primary signals simultaneously.
The NTSC system has been used for public broadcasting on the USA since
December 1953.
The NTSC system, which operates on a 60HZ field and 525 Scanning lines, is designed
to be compatible with the monochrome TV system in the US. The width of the video zone
is 4.5MHz and the width of the channels is 6MHz.
This system has been adopted in the USA, KOREA,CANADA,JAPAN and other countries,
and particularly where the utility electricity mains supply frequency is 60Hz.
The PAL system was proposed by W.Bruch of Germany, PAL is stand for "Phase
Alternation by Line". This system was adopted by many European Countries and
public broadcasting began in 1967 in Germany. This system is almost the same as
the NTSC system for the color TV signals, but differs in the fact that the signal are
inversed by 180 at every horizontal scanning line, therefore using a 1H delay line in the
color receiver, suing a 625 line, 50 field.
The SECAM system broadcast service began in FRANCE in 1967 which was officially
adopted by France, USSR and other countries.
The SECAM is stand for "Sequential couleurs A Memoire" This system operates on a 625
lines, 50 fields, was based on the two distinguishing features of the system,
the use of segmental color signals a memory device, the memory device took the from
of a 1H delay line in the receiver.
This system has disadvantages in the parts of phase divergence and cross talk(leakage
of signals) because of the way that the color signals,divided into two,are simultaneously
transmitted.
TV SYSTEMS STANDARD
FORMAT
NTSC
PAL
SECAM
525
625
625
H-FREQ (KHZ)
15.734
15.625
15.625
V-FREQ (HZ)
59.94
50
50
29.97
25
25
INTERLACED SCANING
2:1
2:1
2:1
ASPECT RATIO
4:3
4:3
4:3
VIDEO MODULATION
AM -
AM -
AM +
FM25
FM50
AM 60%
4.2
4.5
5.5
6.5
3.579545
4.433618
R=4.40625,B=4.25
USA,
GERMANY,
FRANCE,
JAPAN,
W-EUROPE
E-EUROPE,
KOREA
CHINA,
CIS
FCC
CCIR
CCIR
FEATURE
SCAN LINES (H)
COUNTRY
STANDARD SPEC
2. TREND OF TROUBLE
TV receiver is composed of a great many components and the number of which
can be different in accordance with each model. But even that only one of its
composed components is trouble, the TV receiver doesn't operate normally.
The lower the ratio of generating the trouble and the less the number of composed
components are used, the higher the reliability of the receiver is assured.
When using a receiver mode of vacuum tube the trend of trouble increases as time
goes by, but as transistor and IC make an appearance and the used components
decrease considerably be means of employing the integrated circuits,considerable
decreasing of trouble is resulted.
Recently,trouble-shooting which is required of exchanging the whole PCB as well
as the troubled components serves as the assurance of reliability and the satisfaction
of customer.
Localizing the trouble to one stage and a specific component generally should be
required of test equipment such as the multimeter, oscilloscope, and pattern
generator etc.. Just with a simple ohm-meter, test of opened-resistor and
short-capacitor is possible once the trouble has been narrowed down a suspected
component. It's summarized the relation of the symptom of trouble and its circuit.
RELATED CIRCUIT
HV,CRT,FBT
NO COLOR
INCORRECT COLOR
V-DEFLECTION
CONVERGENCE
DY AND PC MAGNET,CRT
NO HOLD SYNC.
SYNC SEPARATOR,AFC,H-OSCILLATOR,AGC,APC
NO SOUND
SINGLE VERTICAL LINE
5. DIAGNOSIS OF TROUBLE
Generally because the TV circuits are composed of so many components it's
not easy to cover the wide range of total parts. Therefore you should presume the
location of trouble by dividing the circuit into the narrow section.
When trouble-shooting is carried out, the multimeter and oscilloscope are mainly
used and by checking the voltage and waveform of each terminal the troubled
component can be detected.
Above all it's very important to accumulate the experience of repair through trial
and error understanding the flow path of signals.
5.1 DIAGNOSIS OF PASSIVE COMPONENTS (RLC)
Opening, short of R,L and C or reduction of capacitance value can be checked
with a simple tester, and only opening test can be also achieved by connecting a
good part with parallel.
In case that it is difficult to determine whether the part is poor or not due to the effect
of other parts, check it after opening the lead.
In the transistor amplifier circuit, forward bias current, forward bias current flow across base and
emitter, its forward voltage is, regardless of the type of transistor, about 0.7V in silicon TR and 0.2V
in germanium TR.
After measuring VB,VE,VC AND VBE, consider it as a normal if the following conditions are satisfied
1) VBE is about 0.6V(or 0.2V), that is, forward biased.
2) VB, VE and VC are within 20% of the value specified in circuit.
Determination of trouble is also done by checking the resistance across the base and emiter,
base and collector, emitter and collector.
That is, after measuring the forward and reverse resistance, if its difference is large it is a normal.
If its difference is small, on the contrary, if its difference is large it is a possible to check it by
the short test with a digital multimeter.
5.3 DIAGNOSIS OF IC CIRCUIT
In case the troubled circuit contains IC the reason of trouble can be IC itself or surrounding
parts.
For diagnosis, first compare the voltage of each terminal with the specification, if it
While as the reason of trouble, there is a case that the supply voltage is wrong and each
terminal voltage of IC is wrong regardless of the normal supply voltage.
In this case try to exchange IC after checking the surrounding components.
6. NOTES
Remarkable items are described in below on troubleshooting, especially special
attention should be paid to dealing with TR and IC as they are very weak to heat
such as overcurrent and static electricity.
SOUND
DETECT
AFT
TUNER
VIDEO
IF
AGC
VIDEO
DETE
SOUND
IF AMP.
SOUND
FM DETECT
VIDEO
AMP
SOUND
AMP.
SPK
COLOR
OUTPUT
BAND
AMP
CRT
DY COIL
COLOR
DEMOD.
ACC
V-DEL
AMP
V-OUT
H-DEL
AMP
H-OUT
COLOR
KILLER
POWER
BURST
AMP
COLOR
SYNC
H-V
SYNC
10
CN-001N
1. NO POWER
11
CN-001N
2. NO PICTURE
NG : GO to the figure c
OK : Go the figure d
1701
MICOM
12
CN-001N
3. NO SOUND
NG : Go to the figure e
OK : Go to the figure f g
1701
MICOM
13
CN-001N
4. CH DONT STOP
NG : Loss of signal or weak signal
OK : Go to the figure h
14
CN-001N
5. NO COLOR
6. NO VERTICAL DEFLECTION
15
CN-001N
7. NO ON-SCREEN DISPLAY
16
NORMAL
ABNORMAL
CHECK VOLTAGE AT
(+) OF C805 (400V 120uF)
310Vdc AT 220V
NORMAL
ABNORMAL
CHECK/REPLACE F801
FUSE(F4AH 250V)
CHECK/REPLACE
D801,D802,D803,D804
(1S1888)
R819 (7W 3.3OHM)
CHECK/REPLACE
I801(STR-F6653)
& PERIPHERAL
COMPONENT
NORMAL
ABNORMAL
CHECK HORIZONTAL
DRIVE PULSE AT PIN 33
OF I501(TDA9361)
[REFER TO WAVE FORM 9]
ABNORMAL
CHECK
Vcc(+8V DC) AT
PIN 14 OF I501
CHECK/REPLACE
I804(LTV-817C)
NORMAL
CHECK/REPLACE
Q402(2SD1207)
T401(TD-10A2)
Q401(2SD2499)
ABNORMAL
CHECK/REPLACE
I823 (3.3V Reg)
CHECK
SDA(PIN2)
&SCL(PIN3)
OK
ABNORMAL
ABNORMAL
CHECK/REPLACE
D840 (1N4148)
D830 (BYV95C)
CHECK/REPLACE
T402 F.B.T
& CRT
NORMAL ABNORMAL
CHECK SDA(PIN 3)
& SCL(PIN 2)
WAVEFORM OF I501
NORMAL
OK
ABNORMAL
CHECK/REPLACE
X502(12MHz)
NORMAL
CHECK/REPLACE
I501
(TDA9361)
17
CP-185
NORMAL
ABNORMAL
CHECK / REPLACE
I 501
CHECK WAVEFORM AT
PIN 40 OF I501
ABNORMAL
CHECK / REPLACE
Q502, Q503
ABNORMAL
NORMAL
NORMAL
NORMAL
ABNORMAL
CHECK / REPLACE
D408, I820
CHECK / REPLACE
I901 (TDA6107Q)
NORMAL
OK
18
CP-185
CHECK / REPLACE
P401 & DY
NORMAL
CHECK SIGNAL AT
PIN1 & PIN2 OF I301 [REFER
TO WAVEFORM 10 11 ]
CHECK / REPLACE
D407(IN4936GP)
D408(IN4936GP)
ABNORMAL
NORMAL
CHECK / REPLACE
CRT
CHECK SIGNAL
AT PIN7 OF I301
CHECK OUTPUT
WAVEFORM AT PIN21, PIN22
OF I501
NORMAL
ABNORMAL
NORMAL
CHECK / REPLACE
R305, D350
D313
CHECK / REPLACE
I301
OK
19
ABNORMAL
CHECK / REPLACE
I501
CP-185
4. NO SOUND ( PICTURE OK )
ABNORMAL
NORMAL
ABNORMAL
CHECK / REPLACE
SF01
NORMAL
NORMAL
( SECAM L/L)
NORMAL
ABNORMAL
CHECK / REPLACE
D813, C821
NG
CHECK POWER
PART CIRCUIT
NORMAL
OK
CHECK VOLTAGE
Vcc(13.5Vdc) AT PIN1
(TDA 7267A)
NORMAL
CHECK / REPLACE
I601(TDA7055)
[ I601(TDA1519B) ]
NORMAL
OK
20
ABNORMAL
CHECK / REPLACE
I101 (TDA9830)
SAW FILTER
CP-185
ABNORMAL
CHECK / REPLACE
Q1 / LED1
(TRANSMITTER BOARD)
CHECK PULSE
AT PIN36 OF I701
NG
OK
CHECK IC1
(DHR-0015)
NG
CHECK / REPLACE
X1, C1
ABNORMAL
OK
CHECK / REPLACE
I704 (TFMU5380)
NORMAL
CHECK / REPLACE
I701 & PERI, COMP
OK
21
NORMAL
ABNORMAL
CHECK VOLTAGE AT
(+) OF C805 (400V 120uF)
310Vdc AT 220V
NORMAL
ABNORMAL
CHECK/REPLACE F801
FUSE(F4AH 250V)
CHECK/REPLACE
D801,D802,D803,D804
(1S1888)
R819 (10W 3.3OHM)
CHECK/REPLACE
I801(STR-F6653)
& PERIPHERAL
COMPONENT
NORMAL
ABNORMAL
CHECK HORIZONTAL
DRIVE PULSE AT PIN 33
OF I501(TDA9367)
[REFER TO WAVE FORM 9]
ABNORMAL
CHECK
Vcc(+8V DC) AT
PIN 14 OF I501
CHECK/REPLACE
I804(LTV-817C)
NORMAL
CHECK/REPLACE
Q402(2SD1207)
T401(TD-10A2)
Q401(2SD2499)
ABNORMAL
CHECK/REPLACE
I823 (3.3V Reg)
CHECK
SDA(PIN 2)
&SCL(PIN 3)
OK
ABNORMAL
ABNORMAL
CHECK/REPLACE
D840 (1N4148)
D830 (BYV95C)
CHECK/REPLACE
T402 F.B.T
& CRT
NORMAL ABNORMAL
CHECK SDA(PIN 3)
& SCL(PIN 2)
WAVEFORM OF I501
NORMAL
OK
ABNORMAL
CHECK/REPLACE
X502(12MHz)
NORMAL
CHECK/REPLACE
I501
(TDA 9367)
22
CP-385
NORMAL
ABNORMAL
CHECK / REPLACE
I 501
CHECK WAVEFORM AT
PIN 40 OF I501
ABNORMAL
CHECK / REPLACE
Q502, Q503
ABNORMAL
NORMAL
NORMAL
NORMAL
ABNORMAL
CHECK / REPLACE
D408, I820
CHECK / REPLACE
I901 (TDA6107Q)
NORMAL
OK
23
CP-385
CHECK / REPLACE
P401 & DY
NORMAL
CHECK SIGNAL AT
PIN 1 & PIN 2 OF I301 [REFER
TO WAVEFORM 10 11 ]
CHECK / REPLACE
D407(IN4936GP)
D408(IN4936GP)
ABNORMAL
NORMAL
CHECK / REPLACE
CRT
CHECK SIGNAL
AT PIN 7 OF I301
CHECK OUTPUT
WAVEFORM AT PIN 21, PIN 22
OF I501
NORMAL
ABNORMAL
NORMAL
CHECK / REPLACE
R305, D350
D313
CHECK / REPLACE
I301
OK
24
ABNORMAL
CHECK / REPLACE
I501
CP-385
4. NO SOUND ( PICTURE OK )
NORMAL
ABNORMAL
CHECK FM SIGNAL
AT PIN 58 OF I601
CANCEL
MUTE FUNCTION
NORMAL
ABNORMAL
NORMAL
CHECK SIGNAL AT
PIN 35 OF I501
CHECK /
REPLACE I501
ABNORMAL
NORMAL
NORMAL
CHECK SIGNAL
AT PIN 28 & 29
OF I501
CHECK / REPLACE
SF02 (K9650M)
Q103, C108
ABNORMAL
ABNORMAL
CHECK / REPLACE
D860, C866
NG
CHECK POWER
PART CIRCUIT
CHECK WAVEFORM
SDA(PIN 10) SCL(PIN 9)
XTAL(PIN 62 & 63)
NORMAL
OK
CHECK VOLTAGE
Vcc(13.5Vdc) AT PIN 3
(TDA8944J)
NORMAL
CHECK / REPLACE
I602
(TDA8944J)
NORMAL
OK
25
NORMAL
CHECK / REPLACE
I601
(MSP3415)
CP-385
ABNORMAL
CHECK / REPLACE
Q1 / LED1
(TRANSMITTER BOARD)
CHECK PULSE
AT PIN 36 OF I701
NG
OK
CHECK IC1
(DHR-0015)
NG
CHECK / REPLACE
X1, C1
ABNORMAL
OK
CHECK / REPLACE
I704 (TFMU5380)
NORMAL
CHECK / REPLACE
I701 & PERI, COMP
OK
26
NORMAL
ABNORMAL
CHECK VOLTAGE AT
(+) OF C805 (400V 180uF)
310Vdc AT 220V
NORMAL
ABNORMAL
CHECK/REPLACE F801
FUSE(F4AH 250V)
CHECK/REPLACE
D801,D802,D803,D804
(1S1888)
R819 (10W 3.3OHM)
CHECK/REPLACE
I801(STR-F6653)
& PERIPHERAL
COMPONENT
NORMAL
ABNORMAL
CHECK HORIZONTAL
DRIVE PULSE AT PIN 33
OF I501(TDA9365)
[REFER TO WAVE FORM 9]
ABNORMAL
CHECK
Vcc(+8V DC) AT
PIN 14 OF I501
CHECK/REPLACE
I804(LTV-817C)
NORMAL
CHECK/REPLACE
Q402(2SD1207)
T401(TD-19A1)
Q401(2SD2578)
ABNORMAL
CHECK/REPLACE
I823 (3.3V Reg)
CHECK
SDA(PIN 2)
&SCL(PIN 3)
OK
ABNORMAL
ABNORMAL
CHECK/REPLACE
D840 (1N4148)
D830 (BYV95C)
CHECK/REPLACE
T402 F.B.T
& CRT
NORMAL ABNORMAL
CHECK SDA(PIN 3)
& SCL(PIN 2)
WAVEFORM OF I501
NORMAL
OK
ABNORMAL
CHECK/REPLACE
X502(12MHz)
NORMAL
CHECK/REPLACE
I501
(TDA9365)
27
CP-785
NORMAL
ABNORMAL
CHECK / REPLACE
I 501
CHECK WAVEFORM AT
PIN 40 OF I501
ABNORMAL
CHECK / REPLACE
Q502, Q503
ABNORMAL
NORMAL
NORMAL
NORMAL
ABNORMAL
CHECK / REPLACE
D408, I820
CHECK / REPLACE
I901 (TDA6107Q)
NORMAL
OK
28
CP-785
CHECK / REPLACE
P401 & DY
NORMAL
CHECK SIGNAL AT
PIN 1 & PIN 2 OF I301 [REFER
TO WAVEFORM 10 11 ]
CHECK / REPLACE
D407(IN4936GP)
D408(IN4936GP)
ABNORMAL
NORMAL
CHECK / REPLACE
CRT
CHECK SIGNAL
AT PIN7 OF I301
CHECK OUTPUT
WAVEFORM AT PIN 21, PIN 22
OF I501
NORMAL
ABNORMAL
NORMAL
CHECK / REPLACE
R305, D350
D313
CHECK / REPLACE
I301
OK
29
ABNORMAL
CHECK / REPLACE
I501
CP-785
4. NO SOUND ( PICTURE OK )
NORMAL
ABNORMAL
CHECK FM SIGNAL
AT PIN58 OF I601
CANCEL
MUTE FUNCTION
NORMAL
ABNORMAL
NORMAL
CHECK SIGNAL AT
PIN 35 OF I501
CHECK /
REPLACE I501
ABNORMAL
NORMAL
NORMAL
CHECK SIGNAL
AT PIN 28 & 29
OF I501
CHECK / REPLACE
SF02 (K9650M)
Q103, C108
ABNORMAL
ABNORMAL
CHECK / REPLACE
D860, C866
NG
CHECK POWER
PART CIRCUIT
CHECK WAVEFORM
SDA(PIN 10) SCL(PIN 9)
XTAL(PIN 62 & 63)
NORMAL
OK
CHECK VOLTAGE
Vcc(13.5Vdc) AT PIN 3
(TDA8946J)
NORMAL
CHECK / REPLACE
I602
(TDA8946J)
NORMAL
OK
30
NORMAL
CHECK / REPLACE
I601
(MSP3415)
CP-785
ABNORMAL
CHECK / REPLACE
Q1 / LED1
(TRANSMITTER BOARD)
CHECK PULSE
AT PIN 36 OF I701
NG
OK
CHECK IC1
(DHR-0015)
NG
CHECK / REPLACE
X1, C1
ABNORMAL
OK
CHECK / REPLACE
I704 (TFMU5380)
NORMAL
CHECK / REPLACE
I701 & PERI, COMP
OK
31