Professional Documents
Culture Documents
5.000in 0.362wall IEU S135 NC50 (6.625 X 3.250 TJ) 9P 12B PDF
5.000in 0.362wall IEU S135 NC50 (6.625 X 3.250 TJ) 9P 12B PDF
Pipe Body
OD (in)
Wall Thickness (in)
Nominal ID (in)
Calculated Plain End Weight (lbs/ft)
New
(Nominal)
5.000
0.362
4.276
17.932
95% RBW
4.964
0.344
4.276
16.968
90% RBW
4.928
0.326
4.276
16.012
Premium
4.855
0.290
4.276
14.121
712,100
74,100
59,300
17,105
15,672
673,800
70,000
56,000
18,571
14,292
635,900
66,000
52,800
17,593
12,892
560,800
58,100
46,500
15,638
10,029
New
(Nominal)
5.275
19.635
14.360
5.708
11.415
API
Premium
4.154
18.514
14.360
4.476
8.953
Notes: Pipe Properties are calculated based on uniform OD and wall thickness
New = 100% RBW. Premium = 80% RBW
Burst Pressure for New based on 87.5% RBW per API
OD (in)
ID (in)
6.625
3.250
9.0
12.0
23.52
31.7
51,200
30,700
25,600
0.36
0.70
0.017
1,133,400
0.69
0.88
6.390
6.313
3.125
5.125
*Connection torsional strength is less than 80% pipe body torsional strength
Box OD (in)
Elevator Capacity (lbs)
Smooth Edge
Height
6.812
1,658,000
5.219
Nominal
TJ OD
6.625
1,440,200
(without IPC)
0.71
0.017
Notes: The Drill Pipe Assembly adjusted weight, capacity and displacement calculations account for the adjusted ID in the manufacture of
95% RBW guaranteed pipe with 0.009" internal plastic coating. These values may vary with actual values due to pipe body mill
tolerances, internal plastic coating tolerances, and other factors.
New pipe guaranteed to 95% RBW will have a smaller ID (4.218'') than new pipe guaranteed to 87.5% RBW
Worn to min TJ OD
for API Premium
6.313
1,073,700
Elevator capacity based on assumed Elevator Bore, no wear factor, and contact stress of 110,100 psi
A raised elevator OD increases elevator capacity without affecting make-up torque
The technical information contained herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy
and suitability of use of the technical information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall
thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end
user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per
Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
JCT 03-21-2011
TorqueTensionGraph
Connection:NC50(6.625(in)ODX3.250(in)ID)SMYS=120,000(psi)
PipeBody:80%InspectionClass,5.000(in)OD,0.362(in)wallthickness,S135PipeGrade
(safetyfactor=1.0)
1,400,000
PipeBodyinCombinedLoading
PipeBodyYieldat80%
InspectionClass
1,200,000
ConnectionPerformance(basedonMUT)
ToolJointYield
ToolJointShoulderSeparation
1,000,000
Tenssion(lbs)
TJOperationalLimit(RecMUT)
TJOperationalLimit(MinMUT)
800,000
600,000
400,000
200,000
Torque(ftlbs)
ConnectionWearforNC50(6.625(in)ODX3.250(in)ID)
MaterialSMYS(specifiedminimumyieldstrength)=120,000(psi)
60,000
50,000
Connection
40,000
T
Torque(ftlbs)
TorsionalStrength
RecommendedMUT
MinimumMUT
30,000
PipeBody
80% ofPremiumPipe
BodyTorsionalStrength
20,000
PipeBody:5.000(in)OD,0.362(in)wall
thickness,S135PipeGrade
10,000
ToolJointOD(in)