Professional Documents
Culture Documents
5.500in 0.415wall IEU S135 XTM57 (7.000 X 4.250 TJ) 12P 17B PDF
5.500in 0.415wall IEU S135 XTM57 (7.000 X 4.250 TJ) 12P 17B PDF
Pipe Body
OD (in)
Wall Thickness (in)
Nominal ID (in)
Calculated Plain End Weight (lbs/ft)
New
(Nominal)
5.500
0.415
4.670
22.538
Premium
5.334
0.332
4.670
17.736
895,000
101,800
81,500
17,826
17,023
704,300
79,800
63,800
16,298
11,177
New
(Nominal)
6.630
23.758
17.129
7.844
15.688
API
Premium
5.217
22.346
17.129
6.145
12.290
Notes: Pipe Properties are calculated based on uniform OD and wall thickness
New = 100% RBW. Premium = 80% RBW
Burst Pressure for New based on 87.5% RBW per API
OD (in)
ID (in)
7.000
4.250
12.0
17.0
28.43
32.3
86,000
51,600
43,000
0.43
0.85
0.020
991,000
0.84
1.08
6.930
6.568
4.125
5.688
Box OD (in)
Elevator Capacity (lbs)
Smooth Edge
Height
N/A
N/A
5.812
Nominal
TJ OD
7.000
1,315,600
(without IPC)
0.86
0.020
Notes: The Drill Pipe Assembly adjusted weight, capacity and displacement calculations account for the adjusted ID in the manufacture of
95% RBW guaranteed pipe with 0.009" internal plastic coating. These values may vary with actual values due to pipe body mill
tolerances, internal plastic coating tolerances, and other factors.
New pipe guaranteed to 95% RBW will have a smaller ID (4.61'') than new pipe guaranteed to 87.5% RBW
Worn to min TJ OD
for API Premium
6.568
808,800
Elevator capacity based on assumed Elevator Bore, no wear factor, and contact stress of 110,100 psi
A raised elevator OD increases elevator capacity without affecting make-up torque
The technical information contained herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy
and suitability of use of the technical information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall
thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end
user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per
Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
JCT 03-21-2011
TorqueTensionGraph
Connection:XTM57(7.000(in)ODX4.250(in)ID)SMYS=120,000(psi)
PipeBody:80%InspectionClass,5.500(in)OD,0.415(in)wallthickness,S135PipeGrade
(safetyfactor=1.0)
1,400,000
PipeBodyinCombinedLoading
PipeBodyYieldat80%
InspectionClass
1,200,000
ConnectionPerformance(basedonMUT)
ToolJointYield
ToolJointShoulderSeparation
1,000,000
Tenssion(lbs)
TJOperationalLimit(RecMUT)
TJOperationalLimit(MinMUT)
800,000
600,000
400,000
200,000
Torque(ftlbs)
ConnectionWearforXTM57(7.000(in)ODX4.250(in)ID)
MaterialSMYS(specifiedminimumyieldstrength)=120,000(psi)
100,000
90,000
80,000
70,000
Connection
T
Torque(ftlbs)
TorsionalStrength
60,000
RecommendedMUT
MinimumMUT
50,000
40,000
PipeBody
80% ofPremiumPipe
BodyTorsionalStrength
30,000
PipeBody:5.500(in)OD,0.415(in)wall
thickness,S135PipeGrade
20,000
10,000
ToolJointOD(in)