Professional Documents
Culture Documents
TASKalfa 221
SERVICE
MANUAL
Published in October 2009
842KJ112
2KJSM062
Rev.2
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF
USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
It may be illegal to dispose of this battery into the municipal waste stream. Check with your local
solid waste officials for details in your area for proper disposal.
ATTENTION
IL Y A UN RISQUE DEXPLOSION SI LA BATTERIE EST REMPLACEE PAR UN MODELE DE
TYPE INCORRECT. METTRE AU REBUT LES BATTERIES UTILISEES SELON LES INSTRUCTIONS DONNEES.
Il peut tre illgal de jeter les batteries dans des eaux dgout municipales. Vrifiez avec les fonctionnaires municipaux de votre rgion pour les dtails concernant des dchets solides et une mise
au rebut approprie.
Revision history
Revision
Date
Replaced pages
Remarks
2-4-1 to 2-4-4
Safety precautions
This booklet provides safety warnings and precautions for our service personnel to ensure the safety of
their customers, their machines as well as themselves during maintenance activities. Service personnel
are advised to read this booklet carefully to familiarize themselves with the warnings and precautions
described here before engaging in maintenance activities.
DANGER: High risk of serious bodily injury or death may result from insufficient attention to or incorrect
compliance with warning messages using this symbol.
WARNING: Serious bodily injury or death may result from insufficient attention to or incorrect compliance
with warning messages using this symbol.
CAUTION: Bodily injury or damage to property may result from insufficient attention to or incorrect
compliance with warning messages using this symbol.
Symbols
The triangle ( ) symbol indicates a warning including danger and caution. The specific point
of attention is shown inside the symbol.
General warning.
Warning of risk of electric shock.
Warning of high temperature.
indicates a prohibited action. The specific prohibition is shown inside the symbol.
General prohibited action.
Disassembly prohibited.
indicates that action is required. The specific action required is shown inside the symbol.
General action required.
Remove the power plug from the wall outlet.
1.Installation Precautions
WARNING
Do not use a power supply with a voltage other than that specified. Avoid multiple connections to
one outlet: they may cause fire or electric shock. When using an extension cable, always check
that it is adequate for the rated current. .............................................................................................
Connect the ground wire to a suitable grounding point. Not grounding the copier may cause fire or
electric shock. Connecting the earth wire to an object not approved for the purpose may cause
explosion or electric shock. Never connect the ground cable to any of the following: gas pipes,
lightning rods, ground cables for telephone lines and water pipes or faucets not approved by the
proper authorities. ............................................................................................................................
CAUTION:
Do not place the copier on an infirm or angled surface: the copier may tip over, causing injury. .......
Do not install the copier in a humid or dusty place. This may cause fire or electric shock. ................
Do not install the copier near a radiator, heater, other heat source or near flammable material.
This may cause fire. .........................................................................................................................
Allow sufficient space around the copier to allow the ventilation grills to keep the machine as cool
as possible. Insufficient ventilation may cause heat buildup and poor copying performance. ...........
Always handle the machine by the correct locations when moving it. ...............................................
Always use anti-toppling and locking devices on copiers so equipped. Failure to do this may cause
the copier to move unexpectedly or topple, leading to injury. ...........................................................
Avoid inhaling toner or developer excessively. Protect the eyes. If toner or developer is accidentally ingested, drink a lot of water to dilute it in the stomach and obtain medical attention immediately. If it gets into the eyes, rinse immediately with copious amounts of water and obtain medical
attention. ......................................................................................................................................
Advice customers that they must always follow the safety warnings and precautions in the copiers
instruction handbook. .....................................................................................................................
Always remove the power plug from the wall outlet before starting machine disassembly. ...............
Always follow the procedures for maintenance described in the service manual and other related
brochures. .......................................................................................................................................
Under no circumstances attempt to bypass or disable safety features including safety mechanisms
and protective circuits. .....................................................................................................................
Always check that the copier is correctly connected to an outlet with a ground connection. .............
Check that the power cable covering is free of damage. Check that the power plug is dust-free. If it
is dirty, clean it to remove the risk of fire or electric shock. ..............................................................
Never attempt to disassemble the optical unit in machines using lasers. Leaking laser light may
damage eyesight. ...........................................................................................................................
Handle the charger sections with care. They are charged to high potentials and may cause electric
shock if handled improperly. ............................................................................................................
CAUTION
Wear safe clothing. If wearing loose clothing or accessories such as ties, make sure they are
safely secured so they will not be caught in rotating sections. ..........................................................
Use utmost caution when working on a powered machine. Keep away from chains and belts. ........
Handle the fixing section with care to avoid burns as it can be extremely hot. ..................................
Check that the fixing unit thermistor, heat and press rollers are clean. Dirt on them can cause
abnormally high temperatures. ........................................................................................................
Do not remove the ozone filter, if any, from the copier except for routine replacement. ....................
Do not pull on the AC power cord or connector wires on high-voltage components when removing
them; always hold the plug itself. .....................................................................................................
Do not route the power cable where it may be stood on or trapped. If necessary, protect it with a
cable cover or other appropriate item. .............................................................................................
Treat the ends of the wire carefully when installing a new charger wire to avoid electric leaks. ........
Run wire harnesses carefully so that wires will not be trapped or damaged. ....................................
After maintenance, always check that all the parts, screws, connectors and wires that were
removed, have been refitted correctly. Special attention should be paid to any forgotten connector,
trapped wire and missing screws. ...................................................................................................
Check that all the caution labels that should be present on the machine according to the instruction
handbook are clean and not peeling. Replace with new ones if necessary. ......................................
Handle greases and solvents with care by following the instructions below: .....................................
Use only a small amount of solvent at a time, being careful not to spill. Wipe spills off completely.
Ventilate the room well while using grease or solvents.
Allow applied solvents to evaporate completely before refitting the covers or turning the power
switch on.
Always wash hands afterwards.
Never dispose of toner or toner bottles in fire. Toner may cause sparks when exposed directly to
fire in a furnace, etc. .......................................................................................................................
Should smoke be seen coming from the copier, remove the power plug from the wall outlet immediately. ............................................................................................................................................
3.Miscellaneous
WARNING
Never attempt to heat the drum or expose it to any organic solvents such as alcohol, other than the
specified refiner; it may generate toxic gas. .....................................................................................
2KJ/2KH
CONTENTS
1-1 Specifications
1-1-1 Specifications..........................................................................................................................................1-1-1
1-1-2 Parts names............................................................................................................................................1-1-4
(1) Body ..................................................................................................................................................1-1-4
(2) Operation panel.................................................................................................................................1-1-5
1-1-3 Machine cross section ............................................................................................................................1-1-6
1-2 Installation
1-2-1 Installation environment .........................................................................................................................1-2-1
1-2-2 Unpacking and installation ......................................................................................................................1-2-2
(1) Installation procedure ........................................................................................................................1-2-2
(2) Setting initial copy modes................................................................................................................1-2-11
1-2-3 Installing the key counter (option) .........................................................................................................1-2-12
1-2-4 Installing the cassette heater (option) ...................................................................................................1-2-17
1-2-5 Installing the cassette heater for paper feeder (option) (22 ppm model only).......................................1-2-19
1-4 Troubleshooting
1-4-1 Paper misfeed detection .........................................................................................................................1-4-1
(1) Paper misfeed indication ...................................................................................................................1-4-1
(2) Paper misfeed detection conditions ..................................................................................................1-4-2
(3) Paper misfeeds .................................................................................................................................1-4-8
1-4-2 Self-diagnosis .......................................................................................................................................1-4-16
(1) Self-diagnostic function ...................................................................................................................1-4-16
(2) Self diagnostic codes ......................................................................................................................1-4-17
1-4-3 Image formation problems ....................................................................................................................1-4-25
(1) No image appears (entirely white)...................................................................................................1-4-26
(2) No image appears (entirely black)...................................................................................................1-4-26
(3) Image is too light. ............................................................................................................................1-4-27
(4) Background is visible.......................................................................................................................1-4-27
(5) A white line appears longitudinally. .................................................................................................1-4-27
(6) A black line appears longitudinally. .................................................................................................1-4-28
(7) A black line appears laterally...........................................................................................................1-4-28
(8) One side of the copy image is darker than the other.......................................................................1-4-28
(9) Black dots appear on the image......................................................................................................1-4-28
(10) Image is blurred...............................................................................................................................1-4-29
(11) The leading edge of the image is consistently misaligned with the original. ...................................1-4-29
(12) The leading edge of the image is sporadically misaligned with the original. ...................................1-4-29
(13) Paper creases. ................................................................................................................................1-4-29
(14) Offset occurs. ..................................................................................................................................1-4-30
(15) Image is partly missing....................................................................................................................1-4-30
(16) Fusing is poor..................................................................................................................................1-4-30
(17) Image is out of focus. ......................................................................................................................1-4-30
(18) Image center does not align with the original center. ......................................................................1-4-31
1-4-4 Electric problems ..................................................................................................................................1-4-32
1-4-5 Mechanical problems ............................................................................................................................1-4-36
2KJ/2KH
2KJ/2KH
2-4 Appendixes
Maintenance parts list .............................................................................................................................2-4-1
Periodic maintenance procedures ..........................................................................................................2-4-2
Chart of image adjustment procedures...................................................................................................2-4-5
Wiring diagram........................................................................................................................................2-4-7
Paper feeder wiring diagram (22 ppm model only) .................................................................................2-4-8
INSTALLATION GUIDE
DOCUMENT PROCESSOR
PAPER FEEDER
DUPLEX UNIT
BUILT-IN FINISHER
JOB SEPARATOR
FAX System (R)
Scan System (F)B
2KJ/2KH
2KJ/2KH
1-1 Specifications
1-1-1
Specifications
2KJ/2KH
Separation system .......................... Curvature separation and separation electrode
Cleaning system ............................. Blade and cleaning roller
Charge erasing system................... Exposure by cleaning lamp
Fusing system................................. Heat roller
Heat source: Halogen heaters
Abnormally high temperature protection devices: thermostats
Main memory .................................. Standard: 64 MB
Maximum: 192 MB
Interface.......................................... Memory card interface: 1
USB interface connector: 1 (USB Hi-speed)
Network interface: 1 (10 BASE-T/100 BASE-TX)
Option interface: 1
Resolution....................................... 600 x 600 dpi
Operating environment ................... Temperature: 10 to 32.5C/50 to 90.5F
Humidity: 15 to 80% RH
Altitude: 2500 m/8,202 ft maximum
Brightness: 1500 lux maximum
Dimensions ..................................... 18 ppm model
568 (W) x 594 (D) x 502 (H) mm (main body only)
22 3/8" (W) x 23 3/8" (D) x 19 3/4" (H) (main body only)
22 ppm model
568 (W) x 594 (D) x 607 (H) mm (main body only)
22 3/8" (W) x 23 3/8" (D) x 23 7/8" (H) (main body only)
Weight............................................. 18 ppm model: 33 kg/72.8 lbs
22 ppm model: 40 kg/88.2 lbs
Space required................................ 838 mm (W) x 594 (D) mm (using MP tray)
33" (W) x 23 3/8" (D) (using MP tray)
Power source.................................. 120 V AC, 60 Hz, 9.7 A
220 to 240 V AC, 50 Hz, 5.1 A
Options ........................................... Document processor, paper feeder, duplex unit, built-in finisher, job separator,
key counter, FAX kit, network scanner kit, hard disk and expansion memory
Printer functions
Printing speed................................. Same as copying speed
First print time ................................. 5.7 s or less
Resolution....................................... 300 dpi, 600 dpi, Fast 1200
Operating system............................ Windows 2000 (Service Pack 2 or later), Windows XP, Windows Server 2003,
Windows Vista, Apple Macintosh OS 10.x
Interface.......................................... USB interface connector: 1 (USB Hi-speed)
Network interface: 1 (10 BASE-T/100 BASE-TX)
Memory........................................... Standard: 128 MB
Maximum: 1152 MB
Page description language ............. PRESCRIBE
1-1-2
2KJ/2KH
Scanner functions
Operating system............................ Windows 2000 (Service Pack 2 or later), Windows XP, Windows Vista
System requirements ...................... CPU 600 MHz or higher
RAM 128 MB or more
Resolution....................................... 600 dpi, 400 dpi, 300 dpi, 200 dpi
File format....................................... TIFF (MMR compression), PDF (MMR compression)
Scanning speed .............................. A4 landscape, Image quality: Text/Photo original
Single scanning: 22 images/min (600 dpi), 22 images/min (300 dpi)
Dual scanning: 11 images/min (600 dpi), 11 images/min (300 dpi)
Network protocol............................. TCP/IP
Transmission system ...................... PC transmission:
Scan to PC
E-mail transmission: Scan to E-mail
Twain scan:
TWAIN Driver
Duplex unit
Type ................................................ Internal type
Paper weight................................... 64 - 105 g/m2
Paper type ...................................... Plain, Recycled
Paper size....................................... A3, B4, A4, A4R, B5, B5R, A5R, Folio, Ledger, Legal, Letter, LetterR,
StatementR, Oficio II, 8K, 16K
Power source.................................. Electrically connected to the machine.
Dimensions ..................................... 363 (W) x 54 (D) x 181 (H) mm
14 5/16" (W) x 2 1/8" (D) x 7 1/8" (H)
Weight............................................. 0.5 kg or less / 1.1 lbs or less
1-1-3
2KJ/2KH
1-1-2
Parts names
(1) Body
2
3
11
13
12
4
10
11
14
15
18
16
25
24
23
19
22
17
20
20
21
Figure 1-1-1
1.
2.
3.
4.
5.
6.
7.
8.
9.
1-1-4
10.
11.
12.
13.
14.
15.
16.
17.
18.
MP tray extension
Slider
Contact glass
Original size indicator plates
Left cover
Front cover
Toner container release lever
Toner container
Charger cleaner rod
19.
20.
21.
22.
23.
24.
25.
2KJ/2KH
(2) Operation panel
33
34
35
37
29
28
30
36
22
32
31
23
27
26
24
14
21
25
20 19
17
12
11
18
16
10
13
15
1
3
Figure 1-1-2
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
1-1-5
2KJ/2KH
1-1-3
6
3
8
5
Light path
Paper path
1.
2.
3.
4.
5.
6.
7.
8.
1-1-6
2KJ/2KH
1-2 Installation
1-2-1
1.
2.
3.
4.
5.
6.
Installation environment
Temperature: 10 to 32.5C/50 to 90.5F
Humidity: 15 to 80% RH
Power supply: 120 V AC, 9.7 A
220 to 240 V AC, 5.1 A
Power source frequency: 50 Hz 0.3%/60 Hz 0.3%
Installation location
Avoid direct sunlight or bright lighting. Ensure that the photoconductor will not be exposed to direct sunlight or
other strong light when removing paper jams.
Avoid locations subject to high temperature and high humidity or low temperature and low humidity; an abrupt
change in the environmental temperature; and cool or hot, direct air.
Avoid places subject to dust and vibrations.
Choose a surface capable of supporting the weight of the machine.
Place the machine on a level surface (maximum allowance inclination: 1).
Avoid air-borne substances that may adversely affect the machine or degrade the photoconductor, such as mercury, acidic of alkaline vapors, inorganic gasses, NOx, SOx gases and chlorine-based organic solvents.
Select a well-ventilated location.
Allow sufficient access for proper operation and maintenance of the machine.
Machine front: 1000 mm/39 3/8" Machine rear: 100 mm/3 15/16"
Machine right: 300 mm/11 13/16" Machine left: 300 mm/11 13/16
1-2-1
2KJ/2KH
1-2-2
Start
Unpack.
Load paper.
Installing toner.
1-2-2
2KJ/2KH
Unpacking.
18 ppm model
Machine
Outer case
Inner frame
Skid
Bottom left pad
Bottom right pad
Top left pad
Top right pad
Machine cover
Eject spacer
Document tray
Power cord
Paper storage bags
2KJ/2KH
22 ppm model
Machine
Outer case
Inner frame
Skid
Bottom left pad
Bottom right pad
Top left pad
Top right pad
Machine cover
Eject spacer
Document tray
Power cord
Paper storage bags
1-2-4
2KJ/2KH
Tape
Plastic sheet
Tape
Tape
Tape
Figure 1-2-4
Tape
Tape
Tape
Tape
Tape
Tape*
Tape*
Figure 1-2-5
1-2-5
2KJ/2KH
Tape
Cassette
Figure 1-2-6
Tape
Tape
Scanner pin
Scanner pin
Figure 1-2-7
1-2-6
2KJ/2KH
Toner
container
Figure 1-2-8
Figure 1-2-9
Toner
container
Figure 1-2-10
1-2-7
2KJ/2KH
Toner container
Figure 1-2-11
Figure 1-2-12
1-2-8
2KJ/2KH
Load paper.
1. Load paper in the cassette.
Installing toner.
1. Turn the main power switch on. Toner installation is started.
2. The drive chain is disengaged when toner
installation is completed.
Run maintenance mode U130 if [Add Toner]
remains displayed even after the drive chain
is disengaged.
1-2-9
2KJ/2KH
Cover
label
Cover
label
Cover
label
Right side
Cover
label
Cover
label
Left side
Cover
label
Figure 1-2-13
1-2-10
2KJ/2KH-1
(2) Setting initial copy modes
Factory settings are as follows:
Maintenance
item No.
Contents
Factory setting
U253
DOUBLE COUNT(A3/LEDGER)
U254
ON
U260
After ejection
U264
U277
30 s
U285
ON
U326
ON
U342
ON
U343
OFF
U344
1-2-11
2KJ/2KH-1
1-2-3
Procedure
1. Press the power key on the operation panel
to off. Make sure that the Power lamp is off
before turning off the main power switch.
And then unplug the power cable from the
wall outlet.
2. Fit the key counter socket assembly to the
key counter retainer using two screws and
nut.
3. Fit the key counter mount to the key counter
cover using two screws.
4. Fit the key counter retainer to the key
counter mount using two screws.
M4 x 6 screw
(B4A04060)
M3 nut
(7BC1003055++H01)
Key counter
mount
(3066060041)
M4 x 6 screw
(B4A04060)
M4 x 6 screw
(B4A04060)
Key counter
socket assembly
M3 x 6 flat-head (3029236241)
screws
(7BB003306H)
Figure 1-2-14
1-2-12
2KJ/2KH
Screw
Screw
Rear cover
Figure 1-2-15
6. Cut out the aperture on the right middle
cover using nippers.
Aperture
Right middle
cover
Figure 1-2-16
7. Remove two screws and remove the shield
cover.
Shield cover
Screw
Screw
Figure 1-2-17
1-2-13
2KJ/2KH-1
Edging
Edging
(7YZM210003++H01)
Figure 1-2-18
Wire saddle
Edging
Wire saddle
Figure 1-2-19
1-2-14
2KJ/2KH
Bands
Shield cover
Figure 1-2-20
Aperture
4-pin
connector
YC12
4-pin
connector
Engine PWB
Figure 1-2-21
1-2-15
2KJ/2KH
key counter
signal cable
Hook
Square hole
Figure 1-2-22
Aperture
4-pin connector
4-pin connector
Hook
Key counter
mounting plate
M4 x 30
screw
Key counter cover
Figure 1-2-23
21. Turn the main power switch on and enter the
maintenance mode.
22. Run maintenance item U204 and select
"KEY-COUNTER".
23. Exit the maintenance mode.
24. Check that the message requesting the key
counter to be inserted is displayed on the
message display when the key counter is
pulled out.
25. Check that the counter counts up as copies
are made.
1-2-16
2KJ/2KH
1-2-4
Screw
Front right
cover
Hook
Hook
Hook
Figure 1-2-24
1-2-17
2KJ/2KH
Edging
Cassette heater
Figure 1-2-25
Clamp
Connector
Figure 1-2-26
1-2-18
2KJ/2KH
1-2-5
Installing the cassette heater for paper feeder (option) (22 ppm model only)
Screw
Pin
Figure 1-2-27
Cassette
heater cable
Cassette heater
Stay
M3 x 8
P tight screw
Figure 1-2-28
1-2-19
2KJ/2KH
Connector
Figure 1-2-29
1-2-20
2KJ/2KH
1-3 Maintenance Mode
1-3-1
Maintenance mode
The machine is equipped with a maintenance function which can be used to maintain and service the machine.
Start
Yes
No
Yes
No
Enter 001 using the cursor
up/down keys or numeric keys
and press the start key.
End
1-3-1
2KJ/2KH
(2) Maintenance modes item list
Section
General
Initialization
Drive, paper
feed, paper
conveying
and cooling
system
Item
No.
Initial
setting*
U000
U001
U002
U003
U004
U005
****************1,*2
U019
U020
U021
U022
U026
U027
U030
U031
U032
U034
2.8/0.0/0.0/0.0/0.0/0.8*1
-2.4/0.0/0.0/0.0/0.0/0.0*1
2.0*1
330/210*1
U035
Optical
U051
30/20/0/-20/-20/20*1
U053
U060
U061
U063
0*1
U065
0.4/0.6/-0.5/0.0/-0.1
-0.2/-0.3/0.0/0.0/0.5/0.0*1
12*1
0/-10*1
U066
0/0*1
U067
-4/0*1
U068
U070
U071
U072
0/0/0*1
U073
U074
U076
U087
U089
U092
U093
U099
0*1
0/0*1
0/0/0/0*1
0*1
ON/35*1
0/0/0/2/3*1
170/30/240*1
*Initial setting for executing U020, *1: The item initialized for executing U020, *2: The item initialized for executing U021
1-3-2
2KJ/2KH
Section
High voltage
Item
No.
U100
U101
Developing
Fuser and
cleaning
Mode setting
Initial
setting*
107*1
60*1
50*1
10*1
27/45/22/45*1
123/126/33/31*1
1/20/42/2*1
U110
U130
U144
U150
U157
U158
U161
U162
Operation
panel and
support
equipment
OFF/5/30*1
145*1
165*1
175*1
185*1
1*1
2*1
-
U163
U167
U198
OFF*1,*2
U199
U200
U202
U203
Checking DP operation
U204
OFF*1,*2
U207
U233
U243
U244
U245
Checking messages
U246
U249
U250
U251
U252
U253
U254
U260
MODE0*1
4/4/4*1
150000*1,*2
JAPAN*1
DOUBLE COUNT
(A3/LEDGER)*1,*2
ON*1,*2
EJECT*1,*2
*Initial setting for executing U020, *1: The item initialized for executing U020, *2: The item initialized for executing U021
1-3-3
2KJ/2KH-1
Section
Mode setting
Item
No.
Initial
setting*
U264
MONTH-DATE-YEAR (inch)
DATE-MONTH-YEAR (metric)
U265
U277
30*1,*2
U285
ON*1
U326
U332
0*1
ON*1,*2
1.0/1.0/1.0*1,*2
U341
U342
ON*1,*2
U343
OFF*1,*2
U344
U345
U402
U403
2.0/3.0/2.0/2.0*1
U404
2.0/3.0/2.0/2.0*1
U407
Network
scanner
U504
U506
Others
U901
U903
U904
U905
U906
U908
U910
Image
processing
0.0*1
10*1,*2
U911
U917
U920
U925
U926
U927
Clearing the all copy counts and machine life counts (one
time only)
U928
U931
U941
U942
U969
U990
U991
U993
OFF*1
100%*1,*2
0/0*1
*Initial setting for executing U020, *1: The item initialized for executing U020, *2: The item initialized for executing U021
1-3-4
2KJ/2KH
(3) Contents of the maintenance mode items
Maintenance
item No.
U000
Description
Outputting an own-status report
Description
Prints out a list of the current settings of all maintenance items, and occurrences of paper jams and service
calls.
Purpose
To check the current setting of the maintenance items, or the occurrences of paper jams and service calls.
Before initializing or replacing the backup RAM, print out a list of the current settings of the maintenance items
so that you can reenter the same settings after initialization or replacement.
Method
1. Press the start key.
2. Select the item to be output.
Display
Output list
MAINTENANCE
JAM
SERVICE CALL
3. Press the start key. The interrupt copy mode is entered and a list is output.
When A4/Letter paper is available, a report of this size is output. If not, specify the paper feed location.
When output is complete, the screen for selecting an item is displayed.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
U001
U002
1-3-5
2KJ/2KH
Maintenance
item No.
U003
Description
Setting the service telephone number
Description
Sets the telephone number to be displayed when a service call code is detected.
Purpose
To set the telephone number to call service when installing the machine.
Setting
1. Press the start key.
2. Enter a telephone number (up to 15 digits) using the numeric keys.
Move the cursor using the cursor left/right keys and select a number or symbol using the cursor up/down
keys.
To enter symbols, press the keys shown below as required.
Key
Symbol
* key
# key
Lighter key
Darker key
Space
1-3-6
2KJ/2KH
Maintenance
item No.
U005
Description
Copying without paper
Description
Simulates the copy operation without paper feed.
Purpose
To check the overall operation of the machine.
Method
1. Press the start key.
2. Select the item to be operated.
Display
Operation
PPC
PPC + DP
1-3-7
2KJ/2KH
Maintenance
item No.
U019
Description
Displaying the ROM version
Description
Displays the part number of the ROM fitted to each PWB.
Purpose
To check the part number or to decide, if the newest version of ROM is installed.
Method
1. Press the start key. The ROM version are displayed.
2. Change the screen using the cursor up/down keys.
Display
Description
MAIN
Main ROM
ENGINE
Engine ROM
LANG(St)
LANG(Op)
MAIN BOOT
PRINTER
Printer ROM
NWS
DP
Optional DP ROM
FINISHER
CASS2
CASS3
CASS4
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
U020
1-3-8
2KJ/2KH
Maintenance
item No.
Description
U021
U022
U026
Description
0000
0101
0102
1-3-9
2KJ/2KH
Maintenance
item No.
U027
Description
Return of backup data
Description
Transfers the backup data of the EEPROM which was transferred with the U026 to flash memory.
Purpose
To use after the main PWB replaced.
Method
1. Press the start key.
2. Select the [EXECUTE] using the cursor up/down keys.
3. Press the start key to transfer the backup data. The screen displays the result.
EXECUTE
CHECK SUM : ****
CODE
: XXXX (See the table below)
Code
Description
0000
0203
Check sum does not agree when reading out from the EEPROM.
Operation
MAIN
DRUM
T1
T2
T3
EJE1
EJE2
1-3-10
2KJ/2KH
Maintenance
item No.
U031
Description
Checking switches for paper conveying
Description
Displays the on-off status of each paper detection switch on the paper path.
Purpose
To check if the switches for paper conveying operate correctly.
Method
1. Press the start key.
2. Turn each switch on and off manually to check the status.
When a switch is detected to be in the ON position, the display for that switch will be highlighted.
Display
Switches
EJE
RES
PF2
PF3
BRA
DUP
JOB
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
U032
PF1
PFBYP
MP solenoid (MPSOL)
REG
DUP
PF2
PF3
PF4
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-11
2KJ/2KH
Maintenance
item No.
U034
Description
Adjusting the print start timing
Description
Adjusts the leading edge registration or center line.
Purpose
Make the adjustment if there is a regular error between the leading edges of the copy image and original.
Make the adjustment if there is a regular error between the center lines of the copy image and original.
Make the adjustment if there is a regular error between the trailing edges of the copy image and original.
Method
1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys. The setting screen for the selected item is
displayed.
Display
Description
Description
Setting
range
Initial
setting
Change in
value per step
RCL ON
-5.0 to 10.0
2.8
0.1 mm
RCL BYP
-5.0 to 10.0
0.0
0.1 mm
RCL T1
-5.0 to 10.0
0.0
0.1 mm
RCL T2
-5.0 to 10.0
0.0
0.1 mm
RCL T3
-5.0 to 10.0
0.0
0.1 mm
RCL DUP
-5.0 to 10.0
0.8
0.1 mm
Correct image
Output
example 1
Output
example 2
Figure 1-3-1
5. Press the start key. The value is set.
Caution
Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.
U034
1-3-12
U066
(P.1-3-19)
U071
(P.1-3-23)
2KJ/2KH
Maintenance
item No.
U034
Description
Adjustment: Center line adjustment
1. Select the item to be adjusted using the cursor up/down keys.
Display
Description
Setting
range
Initial
setting
Change in
value per step
LSU OUT
-7.0 to 10.0
-2.4
0.1 mm
LSU BYP
-7.0 to 10.0
0.0
0.1 mm
LSU T1
-7.0 to 10.0
0.0
0.1 mm
LSU T2
-7.0 to 10.0
0.0
0.1 mm
LSU T3
-7.0 to 10.0
0.0
0.1 mm
LSU DUP
-7.0 to 10.0
0.0
0.1 mm
Correct image
Output
example 1
Output
example 2
Figure 1-3-2
5. Press the start key. The value is set.
Caution
Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.
U034
U067
(P.1-3-20)
U072
(P.1-3-25)
1-3-13
2KJ/2KH
Maintenance
item No.
U034
Description
Adjustment: Trailing edge margin adjustment
1. Select [MGN REAR].
Display
Description
Setting
range
Initial
setting
Change in
value per step
MGN REAR
-4.0 to 10.0
2.0
0.1 ms
Output
example
Figure 1-3-3
5. Press the start key. The value is set.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
U035
Setting
Setting range
Initial setting
LENGTH DATA
Length
330 to 356 mm
330
WIDTH DATA
Width
200 to 220 mm
210
1-3-14
2KJ/2KH
Maintenance
item No.
U051
Description
Adjusting the deflection in the paper
Description
Adjusts the deflection in the paper.
Purpose
Make the adjustment if the leading edge of the copy image is missing or varies randomly, or if the copy paper
is Z-folded.
Adjustment
1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.
Display
Description
Setting
range
Initial
setting
PF1
-50 to 127
30
BYPASS
-50 to 127
20
PF2
Paper feed from optional first paper feeder (standard for 22ppm model)
-50 to 127
PF3
-50 to 127
-20
PF4
-50 to 127
-20
DUPLEX
-50 to 127
20
Original
Copy
example 1
Copy
example 2
Figure 1-3-4
6. Press the start key. The value is set.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-15
2KJ/2KH-1
Maintenance
item No.
U053
Description
Setting the adjustment of the motor speed
Description
Performs fine adjustment of the speeds of the motors.
Purpose
To adjust the speed of the respective motors when the magnification is not correct.
Method
1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.
Display
Description
Setting
range
Initial
setting
MAIN
-5.0 to 5.0
0.4
POLY
-5.0 to 5.0
0.6
EJE
-5.0 to 5.0
-0.5
DRUM
-5.0 to 5.0
0.0
BYP
-5.0 to 5.0
-0.1
CAS
-5.0 to 5.0
-0.2
DUP
-5.0 to 5.0
-0.3
EJE2
-5.0 to 5.0
0.0
EJE3
-5.0 to 5.0
0.0
EJE4
0.0 to 5.0
0.5
DF
-4.0 to 4.0
0.0
Adjustment
1. Press the interrupt key.
2. Press the start key to output an A3/Ledger VTC pattern.
2KJ/2KH
Maintenance
item No.
U060
Description
Adjusting the scanner input properties
Description
Adjusts the image scanning density.
Purpose
Used when the entire image appears too dark or light.
Setting
1. Press the start key.
2. Change the setting using the cursor left/right keys.
Description
Setting range
Initial setting
0 to 23
12
Increasing the setting makes the density lower, and decreasing it makes the density higher.
3. Press the start key. The value is set.
Supplement
While this maintenance item is being executed, copying from an original is available in interrupt copying mode
(which is activated by pressing the interrupt key).
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
Caution
The following settings are also reset to the initial values by performing this maintenance item:
Exposure density gradient set in maintenance mode (U093)
Exposure set in the copy default item of the copier management mode
U061
U063
Setting range
Initial setting
Shading position
-5 to 5
0.17 mm
Increasing the setting moves the shading position toward the machine left, and decreasing it moves the
position toward the machine right.
3. Press the start key. The value is set.
Supplement
While this maintenance item is being executed, copying from an original is available in interrupt copying mode
(which is activated by pressing the interrupt key).
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-17
2KJ/2KH
Maintenance
item No.
U065
Description
Adjusting the scanner magnification
Description
Adjusts the magnification of the original scanning.
Purpose
Make the adjustment if the magnification in the main scanning direction is incorrect.
Make the adjustment if the magnification in the auxiliary scanning direction is incorrect.
Caution
Adjust the magnification of the scanner in the following order.
U053
(P.1-3-16)
U065
(main scanning
direction)
U065
U067
(P.1-3-20)
(auxiliary scanning
direction)
U070
(P.1-3-22)
Method
1. Press the start key.
2. Select the item to be adjusted.
Display
Description
Setting
range
Initial
setting
Change in
value per step
-25 to 25
0.1 %
-25 to 25
-10
0.1 %
Original
Copy
example 1
Copy
example 2
Figure 1-3-6
5. Press the start key. The value is set.
Adjustment: Auxiliary scanning direction
1. Select [SUB SCAN ADJ] using the cursor up/down keys.
1. Press the interrupt key.
2. Place an original and press the start key to make a test copy.
3. Change the setting value using the cursor left/right keys.
For copy example 1, increase the value. For copy example 2, decrease the value.
Original
Copy
example 1
Copy
example 2
Figure 1-3-7
4. Press the start key. The value is set.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-18
2KJ/2KH
Maintenance
item No.
U066
Description
Adjusting the scanner leading edge registration
Description
Adjusts the scanner leading edge registration of the original scanning.
Purpose
Make the adjustment if there is a regular error between the leading edges of the copy image and original.
Adjustment
1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.
Display
Description
Setting
range
Initial
setting
Change in
value per step
ADJUST DATA 1
-32 to 20
0.17 mm
ADJUST DATA2
-20 to 20
0.084 mm
Original
Copy
example 1
Copy
example 2
Figure 1-3-8
6. Press the start key. The value is set.
Caution
Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.
U066
U403
(P.1-3-54)
U071
(P.1-3-23)
U404
(P.1-3-55)
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-19
2KJ/2KH
Maintenance
item No.
U067
Description
Adjusting the scanner center line
Description
Adjusts the scanner center line of the original scanning.
Purpose
Make the adjustment if there is a regular error between the center lines of the copy image and original.
Adjustment
1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.
Display
Description
Setting
range
Initial
setting
Change in
value per step
ADJUST DATA 1
-39 to 39
-4
0.17 mm
ADJUST DATA 2
-39 to 39
0.084 mm
Original
Copy
example 2
Copy
example 1
Figure 1-3-9
6. Press the start key. The value is set.
Caution
Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.
U067
U403
(P.1-3-54)
U072
(P.1-3-25)
U404
(P.1-3-55)
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-20
2KJ/2KH
Maintenance
item No.
U068
Description
Adjusting the scanning position for originals from the DP
Description
Adjusts the position for scanning originals from the DP.
Purpose
Used when the image fogging occurs because the scanning position is not proper when the DP is used. Run
U071 to adjust the timing of DP leading edge when the scanning position is changed.
Setting
1. Press the start key.
2. Change the setting using the cursor left/right keys.
Description
Setting
range
Initial
setting
Change in
value per step
-17 to 17
0.17 mm
Increasing the value moves the image backward, and decreasing it moves the image forward.
3. Press the start key. The value is set.
Supplement
While this maintenance item is being executed, copying from an original is available in interrupt copying mode
(which is activated by pressing the interrupt key).
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-21
2KJ/2KH
Maintenance
item No.
U070
Description
Adjusting the DP magnification
Description
Adjusts the DP original scanning speed.
Purpose
Make the adjustment if the magnification is incorrect in the auxiliary scanning direction when the optional DP
is used.
Adjustment
1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.
Display
Description
Setting
range
Initial
setting
Change in
value per step
CONVEY
SPEED 1
-25 to 25
0.2 mm
CONVEY
SPEED 2
-25 to 25
0.2 mm
Original
Copy
example 1
Copy
example 2
Figure 1-3-10
4. Press the start key. The value is set.
Caution
Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.
U070
U071
(P.1-3-23)
U404
(P.1-3-55)
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-22
2KJ/2KH
Maintenance
item No.
U071
Description
Adjusting the DP scanning timing
Description
Adjusts the DP original scanning timing.
Purpose
Make the adjustment if there is a regular error between the leading or trailing edges of the original and the
copy image when the optional DP is used.
Method
1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.
Display
Description
Setting
range
Initial
setting
Change in
value per step
LEAD 1
-32 to 22
0.2 mm
TRAIL 1
-22 to 32
0.2 mm
LEAD 2
-32 to 22
0.2 mm
TRAIL 2
-22 to 32
0.2 mm
Original
Copy
example 1
Copy
example 2
Figure 1-3-11
5. Press the start key. The value is set.
Caution
Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.
U071
U404
(P.1-3-55)
1-3-23
2KJ/2KH
Maintenance
item No.
U071
Description
Adjustment: Trailing edge registration
1. Select [TRAIL 1] or [TRAIL 2] using the cursor up/down keys.
2. Press the interrupt key.
3. Place an original on the DP and press the start key to make a test copy.
4. Change the setting value using the cursor left/right keys.
For copy example 1, increase the value. For copy example 2, decrease the value.
Original
Copy
example 1
Copy
example 2
Figure 1-3-12
5. Press the start key. The value is set.
Caution
Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.
U071
U404
(P.1-3-55)
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-24
2KJ/2KH
Maintenance
item No.
U072
Description
Adjusting the DP center line
Description
Adjusts the scanning start position for the DP original.
Purpose
Make the adjustment if there is a regular error between the centers of the original and the copy image when
the optional DP is used.
Adjustment
1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.
Display
Description
Setting
range
Initial
setting
Change in
value per step
1sided
-39 to 39
0.15 mm
2sided front
-39 to 39
0.15 mm
2sided back
-39 to 39
0.15 mm
Original
Copy
example 1
Copy
example 2
Figure 1-3-13
6. Press the start key. The value is set.
Caution
Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.
U072
U404
(P.1-3-55)
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-25
2KJ/2KH
Maintenance
item No.
U073
Description
Checking scanner operation
Description
Simulates the scanner operation under arbitrary conditions.
Purpose
To check scanner operation.
Method
1. Press the start key.
2. Select the item to be changed using the cursor up/down keys.
3. Change the setting using the cursor left/right keys.
Display
Operating conditions
Setting range
ZOOM
Magnification
100 to 400%
SIZE
Original size
See below.
LAMP
0 (off) or 1 (on)
Paper size
Setting
Paper size
A4
42
A5R
B5
47
Folio
24
11" x 8 1/2"
52
11" x 17"
36
A3
53
11" x 15"
39
B4
55
8 1/2" x 14"
40
A4R
56
8 1/2" x 11"
41
B5R
58
5 1/2" x 8 1/2"
4. Press the start key. Scanning starts under the selected conditions.
5. To stop operation, press the stop/clear key.
Completion
Press the stop/clear key when scanning stops. The screen for selecting a maintenance item No. is displayed.
U074
Setting range
Initial setting
0 to 8
Increasing the setting makes the luminosity higher, and decreasing it makes the luminosity lower.
3. Press the start key. The value is set.
Supplement
While this maintenance item is being executed, copying from an original is available in interrupt copying mode
(which is activated by pressing the interrupt key).
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-26
2KJ/2KH
Maintenance
item No.
U076
Description
Executing DP automatic adjustment
Description
Uses a specified original and automatically adjusts the following items in the DP scanning section.
Adjusting the DP magnification (U070)
Adjusting the DP scanning timing (U071)
Adjusting the DP center line (U072)
When you run this maintenance mode, the preset values of U070, U071 and U072 will also be updated.
Purpose
To perform automatic adjustment of various items in the DP scanning section.
Method
1. Set a specified original (P/N: 302AC68243) in the DP.
Cut the trailing edge of the original.
5 mm
F
149 1 mm
74 1 mm
Figure 1-3-14
2. Press the start key.
3. Press the start key. Auto adjustment starts.
When adjustment is complete, each adjusted value is displayed.
Display
Description
CONVEY SPEED
DP CENTER
If a problem occurs during auto adjustment, DATA: XX (XX is replaced by an error code) is displayed
and operation stops. Should this happen, determine the details of the problem and either repeat the procedure from the beginning, or adjust the remaining items manually by running the corresponding maintenance items.
Completion
Press the stop/clear key after auto adjustment is complete. The screen for selecting a maintenance item is
displayed.
If the stop/clear key is pressed during auto adjustment, adjustment stops and no settings are changed.
1-3-27
2KJ/2KH
Maintenance
item No.
U087
Description
Setting DP reading position modification operation
Description
The presence or absence of dust is determined by comparing the scan data of the original trailing edge and
that taken after the original is conveyed past the DP original scanning position. If dust is identified, the DP
original scanning position is adjusted for the following originals.
Purpose
When using DP, to solve the problem when black lines occurs due to the dust with respect to original reading
position.
Setting
1. Press the start key.
2. Select ON or OFF using the cursor up/down keys.
Display
Description
ON
OFF
Initial setting: ON
3. Press the start key. The setting is set.
Setting the reference data for identifying dust
Available only when the mode is turned on.
1. Change the setting using the cursor left/right keys.
Description
Setting range
Initial setting
10 to 95
35
Example
The figure indicates the density in 256 levels of gray (0: white, 255: black). When the setting is 35, data
of the level of 35 or higher is regarded as dust and data of lower level is regarded as the background
(scan data taken when there is no original).
2. Press the start key. The value is set.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-28
2KJ/2KH
Maintenance
item No.
U089
Description
Outputting a MIP-PG pattern
Description
Selects and outputs the MIP-PG pattern created in the machine.
Purpose
To check copier status other than scanner when adjusting image printing, using MIP-PG pattern output (without scanning).
Method
1. Press the start key.
2. Select the MIP-PG pattern to be output using the cursor up/down keys.
Display
PG pattern to be output
Purpose
GRAYSCALE
MONO-LEVEL
256-LEVEL
To check resolution
reproducibility in printing.
1 dot-LINE
3. To change the output conditions of MONO-LEVEL and 1dot-LINE, use the cursor left/right keys to
change the preset values and press the start key to register the setting.
Description
Setting range
Initial setting
0 to 255
1dot-LINE
0 to 21
1-3-29
2KJ/2KH
Maintenance
item No.
U092
Description
Adjusting the scanner automatically
Description
Makes auto scanner adjustments in the order below using the specified original.
Adjusting the scanner center line (U067)
Adjusting the scanner leading edge registration (U066)
Adjusting scanner magnification in the auxiliary direction (U065)
When this maintenance item is performed, the settings in U065, U066 and U067 are also changed.
Purpose
Used to make respective auto adjustments for the scanner.
Method
1. Place the specified original (P/N: 302FZ56990) on the contact glass.
2. Press the start key.
3. Press the start key. Auto adjustment starts.
When adjustment is complete, each adjusted value is displayed.
Display
Description
SCN CENTER
SCN TIMING
SUB SCAN
MAIN SCAN
If a problem occurs during auto adjustment, DATA: XX (XX is replaced by an error code) is displayed
and operation stops. Should this happen, determine the details of the problem and either repeat the procedure from the beginning, or adjust the remaining items manually by running the corresponding maintenance items.
Completion
Press the stop/clear key after auto adjustment is complete. The screen for selecting a maintenance item No.
is displayed.
If the stop/clear key is pressed during auto adjustment, adjustment stops and no settings are changed.
1-3-30
2KJ/2KH
Maintenance
item No.
U093
Description
Setting the exposure density gradient
Description
Changes the exposure density gradient in the manual density mode, depending on respective image quality
modes.
Purpose
To set how the image density is altered by a change of one step in the manual density adjustment for respective image quality modes. Also used to make copy images darker or lighter.
Method
1. Press the start key.
2. Select the image quality mode using the cursor up/down keys.
3. Press the start key. The setting screen for the selected item is displayed.
Display
Description
MIXED
TEXT
PHOTO
FAX TEXT
FAX PHOTO
Description
Setting
range
Initial
setting
MIXED DARKER
MIXED LIGHTER
Increasing the setting makes the change in density larger, and decreasing it makes the change smaller.
Image density
Dark
Setting: 0
Setting: 3
Set to LIGHTER
Set to DARKER
Light
Density adjustment
Light
Center
Dark
Figure 1-3-15
3. Press the start key. The value is set.
4. To return to the screen for selecting an item, press the stop/clear key.
Setting: Density in text mode
1. Select the item to be set using the cursor up/down keys.
2. Adjust the setting using the cursor left/right keys.
Display
Description
Setting
range
Initial
setting
TEXT DARKER
TEXT LIGHTER
Increasing the setting makes the change in density larger, and decreasing it makes the change smaller.
3. Press the start key. The value is set.
4. To return to the screen for selecting an item, press the stop/clear key.
1-3-31
2KJ/2KH
Maintenance
item No.
U093
Description
Setting: Density in photo mode
1. Select the item to be set using the cursor up/down keys.
2. Adjust the setting using the cursor left/right keys.
Display
Description
Setting
range
Initial
setting
PHOTO DARKER
PHOTO LIGTER
Increasing the setting makes the change in density larger, and decreasing it makes the change smaller.
3. Press the start key. The value is set.
4. To return to the screen for selecting an item, press the stop/clear key.
Setting: Density in text in fax mode
1. Select the item to be set using the cursor up/down keys.
2. Adjust the setting using the cursor left/right keys.
Display
Description
Setting
range
Initial
setting
0 to 4
0 to 4
Increasing the setting makes the change in density larger, and decreasing it makes the change smaller.
3. Press the start key. The value is set.
4. To return to the screen for selecting an item, press the stop/clear key.
Setting: Density in photo in fax mode
1. Select the item to be set using the cursor up/down keys.
2. Adjust the setting using the cursor left/right keys.
Display
Description
Setting
range
Initial
setting
0 to 6
0 to 6
Increasing the setting makes the change in density larger, and decreasing it makes the change smaller.
3. Press the start key. The value is set.
4. To return to the screen for selecting an item, press the stop/clear key.
Supplement
While this maintenance item is being executed, copying from an original is available in interrupt copying mode
(which is activated by pressing the interrupt key).
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-32
2KJ/2KH
Maintenance
item No.
U099
Description
Adjusting original size detection
Description
Checks the operation of the original size detection sensor and sets the sensing threshold value.
Purpose
To adjust the sensitiveness of the sensor and size judgement time if the original size detection sensor malfunctions frequently due to incident light or the like.
Method
1. Press the start key.
2. Select the item using the cursor up/down keys.
3. Press the start key. The screen for executing each item is displayed.
Display
Description
DATA
B/W LEVEL
Rear of machine
Center of machine
Front of machine
Figure 1-3-16
3. To return to the screen for selecting an item, press the stop/clear key.
Setting
1. Select an item to be set using the cursor up/down keys.
2. Adjust the setting using the cursor left/right keys.
Display
Description
Setting
range
Initial
setting
LEVEL
0 to 255
170
WAIT TIME
0 to 100
30
A4R AREA
220 (mm)/
240 (mm)
240
ORIG AREA
0 to 350
SIZE
0 to 63
1-3-33
2KJ/2KH
Maintenance
item No.
U100
Description
Setting the main high voltage
Description
Changes the surface potential by changing the grid control voltage. Also performs main charging. Also
changes the setting of main charging copy quantity correction.
Purpose
To set the surface potential or check main charging. Also used when reentering data after initializing the set
data.
Start
1. Press the start key.
2. Select the item using the cursor up/down keys.
Display
Description
MC DATA
MC ON
LASER ON/OFF
Turning the main charger on and the laser scanner unit on and off
INTERVAL
COPY CNT
MC ADJUST
Setting range
Initial setting
0 to 255
107
Increasing the setting makes the surface potential higher, and decreasing it makes the potential lower.
3. Press the start key. The value is set.
Setting the main charging copy quantity correction
1. Select the item using the cursor up/down keys.
2. Change the setting using the cursor left/right keys.
Display
Description
Setting range
Initial setting
INTERVAL
Copy interval
1 to 255 (minute)
60
COPY CNT
Copy quantity
50
MC ADJUST
Correction amount
0 to 50 (bit)
10
Copy interval: Sets the time interval from the previous copying. If the time from the previous copying
exceeds this preset value, the copy quantity counter will be reset.
Copy quantity: Sets the copy quantity from which copy quantity correction starts. When the copy quantity counter reaches this preset value, correction will start.
Correction amount: Sets the correction amount for copy quantity correction.
Set the values in the range from 5 to 120 minutes for copy interval, from 10 to 2,000 sheets for copy
quantity, and from 5 to 50 bits for correction amount.
3. Press the start key. The value is set.
Completion
Press the stop/clear key when main charger output stops while a selection item is displayed. The screen for
selecting a maintenance item No. is displayed.
1-3-34
2KJ/2KH
Maintenance
item No.
U101
Description
Setting the other high voltages
Description
Changes the developing bias voltage and transfer/separation voltage.
Purpose
To check the developing bias and the transfer/separation voltage or to take measures against drop of image
density or background fog.
Method
1. Press the start key.
2. Select the item to be set using the cursor up/down keys.
3. Press the start key. The screen for executing each item is displayed.
Display
Description
DEV
TC
SC
Description
Setting range
Initial setting
BIAS C
2 to 255
27
DUTY C
1 to 99
45
BIAS P
2 to 255
22
DUTY P
1 to 99
45
Increasing the setting makes the image lighter; decreasing it makes the image darker.
3. Press the start key. The value is set.
Setting the transfer voltage
1. Select the item to be set using the cursor up/down keys.
2. Change the setting using the cursor left/right keys.
Display
Description
Setting range
Initial setting
TC DATA1
0 to 255
123
TC DATA2
0 to 255
126
OFF TIMING
0 to 255
33
ON TIMING
0 to 255
31
Description
Setting range
Initial setting
SC SEL
0 to 2
SC ON TIMING
0 to 255
20
SC OFF TIMING
0 to 255
42
SC MODE
0 to 3
2KJ/2KH
Maintenance
item No.
Description
U110
U130
1-3-36
2KJ/2KH
Maintenance
item No.
U144
Description
Setting toner loading operation
Description
Sets toner loading operation after completion of copying.
Purpose
To set whether or not toner is loaded on the drum after low density copying. Normally no change is necessary
from the initial setting.
Setting
1. Press the start key.
2. Select ON or OFF using the cursor up/down keys.
Display
Description
ON
Toner loaded
OFF
Description
Setting range
Initial setting
COUNT
1 to 50
PERCENT
Printing ratio
10 to 40
30
Sensor
CONTAINER SENSOR
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-37
2KJ/2KH
Maintenance
item No.
Description
U157
U158
U161
Description
1ST TEMP
120 to 185
145
2ND TEMP
120 to 185
165
COPY TEMP1
160 to 220
175
COPY TEMP2
160 to 220
185
UP TEMP
1 to 99
DOWN TEMP
1 to 99
1-3-38
2KJ/2KH
Maintenance
item No.
Description
U162
U163
U167
1-3-39
2KJ/2KH
Maintenance
item No.
U198
Description
Setting the fuser phase control
Description
Sets the use of fuser phase control to reduce electrical noise generated by the machine.
Purpose
Normally no change is necessary. If electrical noise generated by the machine causes flickering of the lights
around the machine, select fuser phase control to reduces the noise.
Setting
1. Press the start key.
1. Select ON or OFF using the cursor up/down keys.
Display
Description
ON
OFF
Description
FIX TEMP
SURROUND TEMP
HUMIDITY
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
U200
1-3-40
2KJ/2KH
Maintenance
item No.
Description
U202
U203
Checking DP operation
Description
Simulates the original conveying operation separately in the DP.
Purpose
To check the DP operation.
Method
1. Press the start key.
2. Place an original in the DP if running this simulation with paper.
3. Select the item to be operated using the cursor up/down keys.
Display
Operation
ADP
RADP
ADP (NON P)
RADP (NON P)
Description
OFF
Not installed
KEY-CARD
KEY-COUNTER
1-3-41
2KJ/2KH
Maintenance
item No.
Description
U207
U233
Description
MODE 0
MODE 1
1-3-42
2KJ/2KH
Maintenance
item No.
U243
Description
Checking the operation of the DP motors
Description
Turns the motors and solenoids in the DP on.
Purpose
To check the operation of the DP motors or solenoids.
Method
1. Press the start key.
2. Select the item to be operated using the cursor up/down keys.
3. Press the start key. The operation starts.
Display
F MOT
C MOT
R MOT
RJ SL
RP SL
Switches
SET SW
TMG SW
MAT SW
COV SW
REV SW
SZ A SW
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-43
2KJ/2KH
Maintenance
item No.
U245
Description
Checking messages
Description
Displays a list of messages or graphics on the operation panel.
Purpose
To check the messages or graphics to be displayed.
Method
1. Press the start key.
2. Select the item to be displayed using the cursor up/down keys.
3. Press the start key. The selected item is displayed.
Display
Description
Description
Setting
range
Initial
setting
Change in
value per step
FRONT
0 to 8
0.566 mm
REAR
0 to 8
0.566 mm
END
0 to 8
0.566 mm
1-3-44
2KJ/2KH
Maintenance
item No.
Description
U249
U250
Setting range
Initial setting
Maintenance cycle
0 to 9999999
150000
1-3-45
2KJ/2KH
Maintenance
item No.
U252
Description
Setting the destination
Description
Switches the operations and screens of the machine according to the destination.
Purpose
To be executed after replacing the backup RAM on the main PWB or initializing the backup RAM by running
maintenance item U020, in order to return the setting to the value before replacement or initialization.
Method
Press the start key. The screen for selecting an item is displayed.
Setting
1. Press the start key.
2. Select the destination using the cursor up/down keys.
Display
Description
JAPAN METRIC
INCH
EUROPE METRIC
ASIA PACIFIC
CHINA
China specifications
1-3-46
Maintenance
item No.
Title
Japan
Inch
Europe Metric,
Asia Pacific, China
253
Single
Double
Double
264
YEARMONTHDATE
MONTHDATEYEAR
DATEMONTHYEAR
344
ENERGY
STAR
ENERGY
STAR
GEEA
2KJ/2KH
Maintenance
item No.
U253
Description
Switching between double and single counts
Description
Switches the count system for the total counter and other counters.
Purpose
Used to select, according to the preference of the user (copy service provider), if A3/Ledger paper is to be
counted as one sheet (single count) or two sheets (double count).
Setting
1. Press the start key.
2. Select the count system using the cursor up/down keys.
Display
Description
SINGLE COUNT
DOUBLE COUNT(A3/LEDGER)
DOUBLE COUNT(B4)
DOUBLE COUNT(FOLIO/LEGAL)
Description
ON
OFF
Initial setting: ON
3. Press the start key. The setting is set.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-47
2KJ/2KH-1
Maintenance
item No.
U260
Description
Selecting the timing for copy counting
Description
Changes the copy count timing for the total counter and other counters.
Purpose
To be set according to user (copy service provider) request.
If a paper jam occurs frequently in the optional document finisher when the number of copies is counted at the
time of paper ejection, copies are provided without copy counts. The copy service provider cannot charge for
such copying. To prevent this, the copy timing should be made earlier.
If a paper jam occurs frequently in the paper conveying or fuser sections when the number of copies is
counted before the paper reaches those sections, copying is charged without a copy being made. To prevent
this, the copy timing should be made later.
Setting
1. Press the start key.
2. Select the copy count timing using the cursor up/down keys.
Display
Description
FEED
EJECT
Setting
YEAR-MONTH-DATE
Year/Month/Day
MONTH-DATE-YEAR
Month/Day/Year
DATE-MONTH-YEAR
Day/Month/Year
1-3-48
2KJ/2KH-1
Maintenance
item No.
U277
Description
Setting auto application change time
Description
Sets the time that passes until the machine starts automatically printing after completing copying or operation
when the machine is used as a printer.
Purpose
According to user request, changes the setting.
Setting
1. Press the start key.
2. Change the setting using the cursor left/right keys.
Description
Setting range
Default setting
Switching time
30 to 270 (s)
30 (s)
Description
ON
OFF
Initial setting: ON
3. Press the start key. The setting is set.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
U326
Description
ON
OFF
Initial setting: ON
3. Press the start key. The setting is set.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-49
2KJ/2KH
Maintenance
item No.
U332
Description
Setting the size conversion factor
Description
Sets the coefficient of nonstandard sizes in relation to the A4/Letter size. The coefficient set here is used to
convert the black ratio in relation to the A4/Letter size and to display the result in user simulation.
Purpose
To set the coefficient for converting the black ratio for nonstandard sizes in relation to the A4/11" x 8 1/2" size
for copying printing and fax respectively.
Setting
1. Press the start key.
2. Select copying (COPY), printing (PRT) or fax (FAX) using the cursor up/down keys.
3. Change the setting using the cursor left/right keys.
Display
Description
Setting range
Default setting
COPY
0.1 to 3.0
1.0
PRINTER
0.1 to 3.0
1.0
FAX
0.1 to 3.0
1.0
Description
PF1
Cassette
PF2
PF3
PF4
1-3-50
2KJ/2KH
Maintenance
item No.
U342
Description
Setting the ejection restriction
Description
Sets or cancels the restriction on the number of sheets to be ejected continuously when the internal eject tray
is selected as the eject location.
Purpose
According to user request, sets or cancels restriction on the number of sheets.
Setting
1. Press the start key.
2. Select ON or OFF using the cursor up/down keys.
Display
Description
ON
OFF
Initial setting: ON
Details of restriction (number of sheets to be ejected continuously after the start key is pressed)
Condition
Number of sheets
250
150
100
Description
ON
Duplex copy
OFF
Simplex copy
1-3-51
2KJ/2KH
Maintenance
item No.
U344
Description
Setting the low-power mode
Description
Changes the control for low-power mode.
Purpose
According to user request, selects which has priority, the recovery time from low-power or energy saver.
Setting
1. Press the start key.
2. Select control mode using the cursor up/down keys.
Display
Description
ENERGY STAR
GEEA
Description
Setting range
COUNT
0 to 9999
1-3-52
2KJ/2KH
Maintenance
item No.
U402
Description
Adjusting margins of image printing
Description
Adjusts margins for image printing.
Purpose
Make the adjustment if margins are incorrect.
Adjustment
1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.
Display
Description
Setting
range
Initial
setting
Change in
value per step
LEAD
0 to 10.0
3.0
0.1 mm
AC
-3.4 to 10.0
3.0
0.1 mm
TRAIL
-5.0 to 10.0
4.0
0.1 mm
Printer
left margin
(2.51.0 mm)
Printer
right margin
(2.51.0 mm)
Figure 1-3-17
6. Press the start key. The value is set.
Caution
Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.
U402
U403
(P.1-3-54)
U404
(P.1-3-55)
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-53
2KJ/2KH
Maintenance
item No.
U403
Description
Adjusting margins for scanning an original on the platen
Description
Adjusts margins for scanning the original on the platen.
Purpose
Make the adjustment if margins are incorrect.
Adjustment
1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.
Display
Description
Setting
range
Initial
setting
Change in
value per step
A MARGIN
0 to 10.0
2.0
0.1 mm
B MARGIN
0 to 10.0
3.0
0.1 mm
C MARGIN
0 to 10.0
2.0
0.1 mm
D MARGIN
0 to 10.0
2.0
0.1 mm
Scanner
left margin
(2.5+1.5/-2.0 mm)
Scanner
right margin
(2.5+1.5/-2.0 mm)
Figure 1-3-18
6. Press the start key. The value is set.
Caution
Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.
U403
U404
(P.1-3-55)
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-54
2KJ/2KH
Maintenance
item No.
U404
Description
Adjusting margins for scanning an original from the DP
Description
Adjusts margins for scanning the original from the DP.
Purpose
Make the adjustment if margins are incorrect when the optional DP is used.
Caution
Before making this adjustment, ensure that the following adjustments have been made in maintenance mode.
U402
(P.1-3-53)
U403
(P.1-3-54)
U404
Adjustment
1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.
Display
Description
Setting
range
Initial
setting
Change in
value per step
A MARGIN
DP left margin
0 to 10.0
2.0
0.1 mm
B MARGIN
0 to 10.0
3.0
0.1 mm
C MARGIN
DP right margin
0 to 10.0
2.0
0.1 mm
D MARGIN
0 to 10.0
2.0
0.1 mm
Right margin
(2.5+1.5/-2.0 mm)
Left margin
(2.5+1.5/-2.0 mm)
Figure 1-3-19
6. Press the start key. The value is set.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-55
2KJ/2KH
Maintenance
item No.
U407
Description
Adjusting the leading edge registration for memory image printing
Description
Adjusts the leading edge registration during memory copying.
Purpose
Make the following adjustment if there is a regular error between the leading edge of the copy image on the
front face and that on the reverse face during duplex switchback copying.
Caution
Before making this adjustment, ensure that the following adjustments have been made in maintenance mode.
U034
(P.1-3-12)
U402
(P.1-3-53)
U404
(P.1-3-55)
U407
U066
(P.1-3-19)
U403
(P.1-3-54)
U071
(P.1-3-23)
Adjustment
1. Press the start key.
Description
Setting
range
Initial
setting
Change in
value per step
-2.0 to 2.0
0.0
0.1 mm
Original
Copy
example 1
Copy
example 2
Figure 1-3-20
5. Press the start key. The value is set.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-56
2KJ/2KH
Maintenance
item No.
Description
U504
U506
Setting range
Initial setting
Timeout time
10 to 120 (s)
10
1-3-57
2KJ/2KH
Maintenance
item No.
U901
Description
Checking copy counts by paper feed locations
Description
Displays and clears copy counts by paper feed locations.
Purpose
To check the time to replace consumable parts. Also to clear the counts after replacing the consumable parts.
Method
1. Press the start key. The counts by paper feed locations are displayed.
2. Change the screen using the cursor left/right keys.
Display
BYP
MP tray
PF1
Cassette
PF2
PF3
PF4
DUP
Duplex section
When an optional paper feed device is not installed, the corresponding count is not displayed.
Clearing
1. Select the count to be cleared using the cursor up/down keys.
However, PF2, 3, and 4 are displayed only and cannot be cleared.
2. Press the start key. The count is cleared.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
U903
Description
COUNT
TOTAL COUNT
1-3-58
2KJ/2KH
Maintenance
item No.
U904
Description
Checking/clearing the service call counts
Description
Displays or clears the service call code counts by types.
Purpose
To check the service call code status by types. Also to clear the service call code counts after replacing consumable parts.
Method
1. Press the start key.
2. Select the item using the cursor up/down keys.
3. Press the start key. The screen for executing is displayed.
4. Change the screen using the cursor left/right keys.
Display
Description
COUNT
TOTAL COUNT
Description
DP
Counts of optional DP
FINISHER
DP
Display
Description
ADP
RADP
Finisher
Display
Description
CP CNT
STAPLE
BUNDLE EJECT
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-59
2KJ/2KH
Maintenance
item No.
Description
U906
U908
U910
U911
1-3-60
2KJ/2KH
Maintenance
item No.
U917
Description
Setting backup data reading/writing
Description
Stores backup data from the fax control PWB (when an optional fax kit is installed) into CompactFlash or
reads the data from CompactFlash.
Purpose
To store and write data when replacing the PWB.
Setting
1. Press the power key on the operation panel, and after verifying the power indicator has gone off, switch
off the main power switch. And then unplug the power cable from the wall outlet.
2. Remove the screw and remove the slot cover.
3. Insert Compact Flash in a notch hole of the machine.
4. Connect the power plug. While pressing the copier key, turn the main power switch on.
Press and hold on the Copier key until the message "Please wait." disappears.
5. Enter the maintenance item.
6. Press the start key.
7. Select the item using the cursor up/down keys.
Display
Description
SRAMCF:BKUP
CFSRAM:BKUP
SRAMCF:DIAL
CFSRAM:DIAL
8. Press the start key. Reading or writing is executed, and the screen displays the result.
If the operation was successful:
EXECUTE 0100
CHECK SUM ****
CODE 0000
If the operation failed:
EXECUTE 0100
CHECK SUM ****
CODE XXXX
Where XXX is the error code indicating the reason for the failure.
See Error Codes for Operation U917 and U926 below.
9. Press the power key on the operation panel, and after verifying the power indicator has gone off, switch
off the main power switch. And then unplug the power cable from the wall outlet.
10. Remove the Compact Flash from the machine.
11. Refit the slot cover.
Error Codes for Operation U917 and U926
Code
Description
0102
0103
0104
Communication error.
0105
01FF
CF error.
0202
No CF card.
0203
No data in CF card.
0204
CF data is incompatible.
0205
0206
CF read error.
0207
CF write error.
0212
1-3-61
2KJ/2KH
Maintenance
item No.
Description
U920
U925
1-3-62
2KJ/2KH
Maintenance
item No.
U926
Description
Rewriting FAX program
Description
Downloads the fax program and fax fonts when installing an optional fax kit.
Purpose
To run when upgrading the fax program and fax fonts.
Setting
1. Press the power key on the operation panel, and after verifying the power indicator has gone off, switch
off the main power switch. And then unplug the power cable from the wall outlet.
2. Remove the screw and remove the slot cover.
3. Insert Compact Flash in a notch hole of the machine.
4. Connect the power plug. While pressing the copier key, turn the main power switch on.
Press and hold on the Copier key until the message "Please wait." disappears.
5. Enter the maintenance item.
6. Press the start key.
Downloading of the fax program starts and the result shown below is displayed.
If the operation was successful:
EXECUTE 0100
CHECK SUM ****
CODE 0000
If the operation failed:
EXECUTE 0100
CHECK SUM ****
CODE XXXX
Where XXX is the error code indicating the reason for the failure.
7. Then, downloading of the fax fonts starts and the result shown below is displayed.
If the operation was successful:
EXECUTE 0100
CHECK SUM ****
CODE 0000
If the operation failed:
EXECUTE 0100
CHECK SUM ****
CODE XXXX
Where XXX is the error code indicating the reason for the failure.
See Error Codes for Operation U917 and U926 on P.1-3-61.
8. Press the power key on the operation panel, and after verifying the power indicator has gone off, switch
off the main power switch. And then unplug the power cable from the wall outlet.
9. Remove the Compact Flash from the machine.
10. Refit the slot cover.
1-3-63
2KJ/2KH
Maintenance
item No.
Description
U927
Clearing the all copy counts and machine life counts (one time only)
Description
Resets all of the counts back to 0.
Purpose
To start the counters with value 0 when installing the machine.
Supplement
The total account counter and the machine life counter can be cleared only once if all count values are 1000
or less.
Method
1. Press the start key.
2. Select [EXECUTE] using the cursor up/down keys.
3. Press the start key. All copy counts and machine life counts are cleared.
[CANNOT EXECUTE] is displayed if the count cannot be cleared.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
U928
U931
Description
ON
OFF
1-3-64
2KJ/2KH
Maintenance
item No.
U941
Description
Setting the default magnification ratio of the default cassette
Description
Sets the default magnification ratio when paper selection of copy default setting is set to the default cassette.
Purpose
To be set according to user request.
Setting
1. Press the start key.
2. Select the magnification using the cursor up/down keys.
Display
Description
100
100% magnification
Aut
Description
Setting range
Initial setting
FEED MOT
-10 to 20
REV MOT
-10 to 20
1-3-65
2KJ/2KH
Maintenance
item No.
Description
U990
U991
Description
COPY
FAX
NWS
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-66
2KJ/2KH
Maintenance
item No.
U993
Description
Outputting a VTC-PG pattern
Description
Selects and outputs a VTC-PG pattern created in the machine.
Purpose
When performing respective image printing adjustments, used to check the machine status apart from that of
the scanner with a non-scanned output VTC-PG pattern.
Method
1. Press the start key.
2. Select the VTC-PG pattern to be output using the cursor up/down keys.
Display
PG pattern to be output
Purpose
PG1
PG2
PG3
1-3-67
2KJ/2KH
1-3-2
Management mode
In addition to a maintenance function for service, the machine is equipped with a management function which can be operated by users (mainly by the administrator). In this management mode, settings such as default settings can be changed.
Start
1-3-68
2KJ/2KH
(2) Setting the job accounting
Registering a new account
Registers ID-codes and the limit of use for each
account.
1. Select [Edit Job Accounting] and then press the
enter key.
2. Select [New registration] and then press the enter
key.
3. Enter the ID-code (up to 8 digits) using the numeric
keys.
4. Press the enter key.
5. Set the limit of use.
Deleting an account
1. Select [Edit Job Accounting] and then press the
enter key.
2. Select [Delete] and then press the enter key.
3. Select the ID-code to delete and then press the
enter key.
4. Select [Yes] or [No] and then press the enter key.
1-3-69
2KJ/2KH
(3) Copy default
Density mode
Selects the exposure mode at power-on.
1. Select [Exposure Mode] and then press the enter
key.
2. Select [Manual] or [Auto] and then press the enter
key.
Paper selection
Sets whether the copier will automatically select the
same size of copy paper as the original once an original is set, or whether the designated default drawer will
be automatically selected.
1. Select [Paper Select] and then press the enter key.
2. Select [Auto] or [Default cassette] and then press
the enter key.
Default cassette
Sets one cassette that will be selected automatically
regardless of the size of paper loaded in that cassette.
1. Select [Default cassette] and then press the enter
key.
2. Select the drawer that will be used with priority.
Settings: Cassette 1/Cassette 2/Cassette 3/ Cassette 4
1-3-70
Default magnification
Sets whether or not the appropriate magnification ratio
to be calculated automatically when selecting the size
of copy paper.
1. Select [Default magnif.] and then press the enter
key.
2. Select [100%] or [Auto %] and then press the enter
key.
Collate copying
Determines whether or not the Sort mode will be the
default setting in the initial mode.
1. Select [Collate] and then press the enter key.
2. Select [On] or [Off] and then press the enter key.
2KJ/2KH
Offset copying
Determines whether or not the offset copy will be the
default setting in the initial mode.
1. Select [Offset] and then press the enter key.
2. Select [On] or [Off] and then press the enter key.
1-3-71
2KJ/2KH
Original orientation
Sets the default original orientation.
1. Select [Orig. direction] and then press the enter
key.
2. Select [Top Edge Top] or [Top Edge Left] and then
press the enter key.
Key sound
Sets whether or not the operation panel will emit a
beep sound each time a key is pressed.
1. Select [Key sound On/Off] and then press the enter
key.
2. Select [On] or [Off] and then press the enter key.
1-3-72
Auto sleep
Sets whether or not to have the auto sleep function.
This setting is displayed only on the inch specification
model.
1. Select [Auto Sleep] and then press the enter key.
2. Select [On] or [Off] and then press the enter key.
Auto clear
Sets whether or not to have the auto clear function.
1. Select [Auto Clear] and then press the enter key.
2. Select [On] or [Off] and then press the enter key.
Silent mode
Sets whether or not to use the silent mode which shortens the length of time that the laser data writing motor
continues to spin after each copy job is finished.
1. Select [Silent Mode] and then press the enter key.
2. Select [On] or [Off] and then press the enter key.
2KJ/2KH
Machine administrator management code change
Changes the four-digit management code for the security administrator of the other machine.
1. Select [MachineAdminCode] and then press the
enter key.
2. Enter a new security administrator management
code using the numeric keys.
1-3-73
2KJ/2KH
1-3-74
2KJ/2KH
1-4 Troubleshooting
1-4-1
8
7
6
5
1
4
Figure 1-4-1
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Misfeed in cassette
Misfeed in first paper feeder
Misfeed in second paper feeder
Misfeed in third paper feeder
Misfeed in MP tray
Misfeed in paper conveying section
Misfeed in eject section
(job separator or built-in finisher)
Misfeed in document processor
1-4-1
2KJ/2KH
(2) Paper misfeed detection conditions
OSBSW
DPTSW
PCSW
ESW
FSSW
DUP
PCSW
RCL
RSW
MP
SOL
PFCL
CPFCL1
CFSW1
CPFCL2
CFSW2
CPFCL3
Figure 1-4-2
1-4-2
2KJ/2KH
Section
System
Paper
feed
section
Description
00
No paper feed
Conditions
Specified time
04
Cover open
05
Secondary paper feed
does not start
30 s
10
No paper feed from MP
tray
1570 ms
11
No paper feed from
cassette
1327 ms
12
No paper feed from first
paper feeder
2290 ms
13
No paper feed from
second paper feeder
1953 ms
14
No paper feed from
third paper feeder
1953 ms
15
Misfeed in vertical
paper conveying section 1
2243 ms
1916 ms
1916 ms
16
Misfeed in vertical
paper conveying section 2
1916 ms
20
Multiple sheets in MP
tray
5907 ms
The registration switch (RSW) does not turn off within the 1570 ms
specified time of paper MP solenoid (MPSOL) turning on.
1-4-3
2KJ/2KH
Section
Paper
feed
section
Description
5907 ms
The registration switch (RSW) does not turn off within the
specified time of paper feed clutch (PFCL) turning on.
1327 ms
22
Multiple sheets in first
paper feeder
5907 ms
The registration switch (RSW) does not turn off within the
specified time of cassette paper feed clutch 1 (CPFCL1)
turning on.
2290 ms
5907 ms
1953 ms
5907 ms
1953 ms
A message, which is not the one indicating start of secondary paper feed, is received when the machine waits
for start of secondary paper feed.
2523 ms
2243 ms
2243 ms
1589 ms
40
Misfeed in fuser section
(MP tray)
2766 ms
2766 ms
41
Misfeed in fuser section
(cassette)
2766 ms
2766 ms
42
Misfeed in fuser section
(first paper feeder)
2766 ms
43
Misfeed in fuser section
(second paper feeder)
2766 ms
24
Multiple sheets in third
paper feeder
Fuser
section
1-4-4
Specified time
21
Multiple sheets in cassette
23
Multiple sheets in second paper feeder
Paper
conveying
section
Conditions
30
Misfeed in registration/
transfer section
2KJ/2KH
Section
Fuser
section
Eject
section
Feedshift
section
Description
Conditions
44
Misfeed in fuser section
(third paper feeder)
2766 ms
45
Misfeed in fuser section
(duplex section)
2766 ms
50
The eject switch (ESW) does not turn off within specified
Misfeed in eject section time of the registration switch (RSW) turning off.
2766 ms
The eject switch (ESW) does not turn off within specified
time of the registration clutch (RCL) turning on.
2766 ms
51
Misfeed in job separator eject section
The job eject switch (JBESW) does not turn off within
specified time of the feedshift switch (FSSW) turning on.
2056 ms
The job eject switch (JBESW) does not turn off within
specified time of the feedshift switch (FSSW) turning off.
2056 ms
52
Misfeed in feedshift
section (MP tray)
2056 ms
1364 ms
2766 ms
5907 ms
2056 ms
1364 ms
2766 ms
5907 ms
2056 ms
1364 ms
2766 ms
5907 ms
2056 ms
1364 ms
2766 ms
5907 ms
53
Misfeed in feedshift
section (cassette)
54
Misfeed in feedshift
section (first paper
feeder)
55
Misfeed in feedshift
section (second paper
feeder)
Specified time
1-4-5
2KJ/2KH
Section
Feedshift
section
Duplex
section
Description
56
Misfeed in feedshift
section (third paper
feeder)
1-4-6
Specified time
2056 ms
1364 ms
2766 ms
5907 ms
57
The job eject switch (JBESW) does not turn on within
Misfeed in feedshift
specified time of the feedshift switch (FSSW) turning on.
section (duplex section)
The feedshift switch (FSSW) does not turn on within
specified time of paper switchback operation.
2056 ms
2766 ms
5907 ms
3037 ms
3037 ms
3037 ms
1589 ms
1589 ms
70
No original feed
71
An original jam in the
original conveying section 1
72
An original size error
jam
1145 pulses
73
An original jam in the
original conveying section 2
9900 pulses
74
An original jam in the
original conveying section 3
2300 pulses
60
Misfeed in duplex
paper conveying section
61
Misfeed in duplex eject
section
Document
processor
Conditions
1364 ms
2KJ/2KH
Section
Document
processor
Finisher
Description
Conditions
Specified time
75
An original jam in the
original switchback
section
During original switchback in the duplex mode, the original switchback switch (OSBSW) does not turn on within
specified time of the original conveying motor (OCM)
turning on.
10700 pulses
78
Document processor
cover open
80
Jam between the finisher and machine
Paper ejection is not output from the machine to the document finisher within specified time of the paper conveying switch (PCSW) turning on.
15 s
81
Finisher paper entry
nonarrival jam
2598 ms
83
Finisher paper entry
jam
84
Finisher eject jam
2570 ms
1869 ms + Paper
length
1-4-7
2KJ/2KH
(3) Paper misfeeds
Problem
Causes/check procedures
Corrective measures
(1)
A paper jam in the
paper feed, conveying or eject section is
indicated as soon as
the main power
switch is turned on.
Defective switch.
Run maintenance item U031 and turn switch on and off manually.
Replace the switch if indication of the corresponding switch is not
light.
Registration switch, eject switch, feedshift switch
(2)
A paper jam in the
paper feed section is
indicated during
copying (no paper
feed from MP tray).
Jam code 10
Defective registration
switch.
(3)
A paper jam in the
paper feed section is
indicated during
copying (no paper
feed from cassette).
Jam code 11
(4)
A paper jam in the
paper feed section is
indicated during
copying (no paper
feed from first paper
feeder).
Jam code 12
1-4-8
Check if the paper feed pul- Check visually and replace any deformed pulley.
ley, separation pulley or forwarding pulley is deformed.
Broken registration switch
actuator.
Defective registration
switch.
Run maintenance item U032 and select the paper feed clutch to
be turned on and off. Check the status and remedy if necessary.
Check if the paper feed pul- Check visually and replace any deformed pulley.
ley, separation pulley or forwarding pulley is deformed.
Broken registration switch
actuator.
Defective registration
switch.
Run maintenance item U032 and select the cassette paper feed
clutch 1 to be turned on and off. Check the status and remedy if
necessary.
2KJ/2KH
Problem
(5)
A paper jam in the
paper feed section is
indicated during
copying (no paper
feed from second
paper feeder).
Jam code 13
(6)
A paper jam in the
paper feed section is
indicated during
copying (no paper
feed from third paper
feeder).
Jam code 14
(7)
A paper jam in the
paper feed section is
indicated during
copying (misfeed in
vertical paper conveying section 1).
Jam code 15
Causes/check procedures
Paper is extremely curled.
Corrective measures
Change the paper.
Check if the paper feed pul- Check visually and replace any deformed pulley.
ley, separation pulley or forwarding pulley is deformed.
Broken cassette feed
switch 1 actuator.
Run maintenance item U032 and select the cassette paper feed
clutch 2 to be turned on and off. Check the status and remedy if
necessary.
Check if the paper feed pul- Check visually and replace any deformed pulley.
ley, separation pulley or forwarding pulley is deformed.
Broken cassette feed
switch 2 actuator.
Run maintenance item U032 and select the cassette paper feed
clutch 3 to be turned on and off. Check the status and remedy if
necessary.
Defective switch.
Run maintenance item U031 and turn switch on and off manually.
Replace the switch if indication of the corresponding switch is not
light.
Registration switch, cassette feed switch 1, 2
1-4-9
2KJ/2KH
Problem
(8)
A paper jam in the
paper feed section is
indicated during
copying (misfeed in
vertical paper conveying section 2).
Jam code 16
(9)
A paper jam in the
paper feed section is
indicated during
copying (multiple
sheets in MP tray).
Jam code 20
(10)
A paper jam in the
paper feed section is
indicated during
copying (multiple
sheets in cassette).
Jam code 21
1-4-10
Causes/check procedures
Corrective measures
Defective switch.
Run maintenance item U031 and turn switch on and off manually.
Replace the switch if indication of the corresponding switch is not
light.
Cassette feed switch 1, 2
Defective registration
switch.
Defective registration
switch.
Run maintenance item U032 and select the paper feed clutch to
be turned on and off. Check the status and remedy if necessary.
2KJ/2KH
Problem
Causes/check procedures
(11)
A paper jam in the
paper feed section is
indicated during
copying (multiple
sheets in first paper
feeder).
Jam code 22
Defective registration
switch.
Run maintenance item U032 and select the cassette paper feed
clutch 1 to be turned on and off. Check the status and remedy if
necessary.
Run maintenance item U032 and select the cassette paper feed
clutch 2 to be turned on and off. Check the status and remedy if
necessary.
Run maintenance item U032 and select the cassette paper feed
clutch 3 to be turned on and off. Check the status and remedy if
necessary.
(12)
A paper jam in the
paper feed section is
indicated during
copying (multiple
sheets in second
paper feeder).
Jam code 23
(13)
A paper jam in the
paper feed section is
indicated during
copying (multiple
sheets in third paper
feeder).
Jam code 24
Corrective measures
1-4-11
2KJ/2KH
Problem
Causes/check procedures
Corrective measures
(14)
A paper jam in the
paper conveying section is indicated during copying (misfeed
in registration/transfer section).
Jam code 30
Defective switch.
Run maintenance item U031 and turn switch on and off manually.
Replace the switch if indication of the corresponding switch is not
light.
Registration switch, cassette feed switch 1, duplex paper conveying switch
(15)
A paper jam in the
fuser section is indicated during copying
(misfeed in fuser section).
Jam codes 40, 41,
42, 43, 44 and 45
Run maintenance item U031 and turn switch on and off manually.
Replace the switch if indication of the corresponding switch is not
light.
Eject switch, feedshift switch
(16)
Broken eject switch or regA paper jam in the
istration switch actuator.
eject section is indiDefective switch.
cated during copying
(misfeed in eject section).
Jam code 50
Check if the registration
clutch malfunctions.
(17)
A paper jam in the
eject section is indicated during copying
(misfeed in job separator eject section).
Jam code 51
1-4-12
Defective switch.
Run maintenance item U031 and turn switch on and off manually.
Replace the switch if indication of the corresponding switch is not
light.
Feedshift switch, job eject switch
2KJ/2KH
Problem
(18)
A paper jam in the
feedshift section is
indicated during
copying (misfeed in
feedshift section).
Jam code 52, 53, 54,
55, 56, 57
(19)
A paper jam in the
duplex section is indicated during copying
(misfeed in duplex
paper conveying section). Jam code 60
(20)
A paper jam in the
duplex section is indicated during copying
(misfeed in duplex
eject section).
Jam code 61
(21)
An original jams in
DP is indicated during copying (no original feed).
Jam code 70
Causes/check procedures
Corrective measures
Defective switch.
Run maintenance item U031 and turn switch on and off manually.
Replace the switch if indication of the corresponding switch is not
light.
Feedshift switch, registration switch, job eject switch
Defective switch.
Run maintenance item U031 and turn switch on and off manually.
Replace the switch if indication of the corresponding switch is not
light.
Feedshift switch, duplex paper conveying switch
Run maintenance item U032 and select the duplex feed clutch to
be turned on and off. Check the status and remedy if necessary.
Defective switch.
Run maintenance item U031 and turn switch on and off manually.
Replace the switch if indication of the corresponding switch is not
light.
Duplex paper conveying switch, registration switch
Run maintenance item U032 and select the duplex feed clutch to
be turned on and off. Check the status and remedy if necessary.
Run maintenance item U244 and turn the original set switch on
and off manually. Replace the switch if indication of the corresponding switch is not light.
Run maintenance item U243 and select the original feed motor to
be turned on and off. Check the status and remedy if necessary.
1-4-13
2KJ/2KH
Problem
Causes/check procedures
Corrective measures
(22)
An original jams in
DP is indicated during copying (an original jam in the original
conveying section 1).
Jam code 71
Run maintenance item U244 and turn the DP timing switch on and
off manually. Replace the switch if indication of the corresponding
switch is not light.
(23)
An original jams in
DP is indicated during copying (an original size error jam).
Jam code 72
Run maintenance item U244 and turn the DP timing switch on and
off manually. Replace the switch if indication of the corresponding
switch is not light.
(24)
An original jams in
DP is indicated during copying (an original jam in the original
conveying section 2).
Jam code 73
Run maintenance item U244 and turn the DP timing switch on and
off manually. Replace the switch if indication of the corresponding
switch is not light.
(25)
An original jams in
DP is indicated during copying (an original jam in the original
conveying section 3).
Jam code 74
Run maintenance item U244 and turn the DP timing switch on and
off manually. Replace the switch if indication of the corresponding
switch is not light.
(26)
An original jams in
DP is indicated during copying (an original jam in the original
switchback section).
Jam code 75
Run maintenance item U244 and turn the DP timing switch on and
off manually. Replace the switch if indication of the corresponding
switch is not light.
(27)
Extremely curled paper.
A paper jam in finDefective paper conveying
isher is indicated durswitch.
ing copying (jam
between the finisher
and machine).
Jam code 80
(28)
Extremely curled paper.
A paper jam in finDefective paper conveying
isher is indicated durswitch.
ing copying (finisher
paper entry nonarrival jam).
Jam code 81
1-4-14
2KJ/2KH
Problem
Causes/check procedures
(30)
Defective paper conveying
A paper jam in finswitch.
isher is indicated during copying (finisher
eject jam).
Check if the feedshift roller
Jam code 84
or feedshift pulley is
deformed.
Check if the eject roller or
eject pulley is deformed.
Corrective measures
With 5 V DC present at YC2-23 on the finisher control PWB,
check if YC2-21 on the finisher control PWB remains low or high
when the paper conveying switch is turned on and off. If it does,
replace the paper conveying switch.
Check visually and replace.
1-4-15
2KJ/2KH
1-4-2
Self-diagnosis
Contents
Operation
0410
0420
0440
0500
0510
Table 1-4-1
Contents
C8170
C8180
C8190
C8210
1-4-16
Contents
Fuser heater break
C6020
C6050
C6400
2KJ/2KH
(2) Self diagnostic codes
Remarks
Code
Contents
Causes
C0030
C0070
Fax software or
main software is
something of the
other machine.
C0100
Defective main
PWB.
C0110
Data damage of
EEPROM.
C0130
Defective main
PWB.
Device damage of
EEPROM.
C0140
C0150
Defective engine
PWB.
Device damage of
EEPROM.
C0160
Data damage of
EEPROM.
C0170
Data damage of
EEPROM.
Defective PWB.
Data damage of
EEPROM.
C0180
1-4-17
2KJ/2KH
Remarks
Code
Contents
C0210
C0240
C0250
C0280
C0410
C0420
C0440
C0500
C0510
1-4-18
Causes
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Defective PWB.
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Defective main
PWB.
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Defective PWB.
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Defective PWB.
Defective PWB.
Defective PWB.
Defective PWB.
Second paper
feeder installed
incorrectly.
Defective PWB.
Defective PWB.
2KJ/2KH
Remarks
Code
C0610
Contents
Bitmap (DIMM) problem
There is a problem with the data or
address bus of the bitmap DRAM.
Causes
Defective main
PWB.
DIMM installed
incorrectly.
Defective DIMM.
C0630
DMA problem
DMA transmission of compressed,
decompressed, rotated, relocated or
blanked-out image data does not complete within the specified period of time.
Defective main
PWB.
C0800
Defective main
PWB.
C0820
C0830
C0860
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Defective PWB.
C0880
C0890
C0900
C0870
1-4-19
2KJ/2KH
Remarks
Code
Contents
Causes
C0920
C2000
Defective drive
transmission system.
Defective engine
PWB.
Defective drive
motor.
Defective drive
transmission system.
Defective engine
PWB.
Defective drum
motor.
Defective home
position switch.
Defective scanner
motor.
Defective engine
PWB.
C2200
C3100
1-4-20
2KJ/2KH
Remarks
Code
C3200
C3300
C4000
C4010
C4200
Contents
Exposure lamp problem
Non-lighting of the exposure lamp is
detected at the beginning of copying.
AGC problem
After AGC, correct input is not obtained
at CCD.
BD steady-state problem
ASIC detects a BD error for 600 ms after
the polygon motor rotation has been stabilized.
Causes
Defective exposure
lamp.
Incorrect shading
position.
Defective PWB.
Defective exposure
lamp.
Defective PWB.
Defective polygon
motor.
Defective engine
PWB.
Defective polygon
motor.
Defective engine
PWB.
Defective laser
scanner unit.
Defective engine
PWB.
1-4-21
2KJ/2KH
Remarks
Code
Contents
C6000
C6020
C6050
C6400
1-4-22
Causes
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Fuser thermistor
installed incorrectly.
Fuser thermostat
triggered.
Fuser heater
installed incorrectly.
Broken fuser
heater wire.
Shorted thermistor.
Broken heater con- Replace the power source PWB and check
trol circuit on the
for correct operation.
power source
PWB.
Poor contact in the
fuser thermistor
connector terminals.
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Fuser thermistor
installed incorrectly.
Fuser thermostat
triggered.
Fuser heater
installed incorrectly.
Broken fuser
heater wire.
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Defective power
source PWB.
Defective engine
PWB.
2KJ/2KH
Remarks
Code
C7800
C7810
C8170
C8180
Contents
Causes
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Defective humidity
sensor.
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Defective humidity
sensor.
The front side reg- Reinsert the connector. Also check for contiistration motor con- nuity within the connector cable. If none,
nector makes poor remedy or replace the cable.
contact.
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Defective finisher
control PWB.
The rear side regReinsert the connector. Also check for contiistration motor con- nuity within the connector cable. If none,
nector makes poor remedy or replace the cable.
contact.
Defective rear side
registration motor.
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Defective finisher
control PWB.
1-4-23
2KJ/2KH
Remarks
Code
Contents
C8190
C8210
1-4-24
Causes
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Defective trailing
edge registration
motor.
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
Defective trailing
edge registration
home position sensor.
Defective finisher
control PWB.
Reinsert the connector. Also check for continuity within the connector cable. If none,
remedy or replace the cable.
The stapler is
blocked with a staple.
Defective finisher
control PWB.
2KJ/2KH
1-4-3
(16)Fusing is poor.
(17)Image is out of
focus.
(4)Background is
visible.
(18)Image center
does not align with
the original center.
1-4-25
2KJ/2KH
(1) No image appears (entirely white).
Copy example
Causes
No transfer charging.
No LSU
laser is
output.
No developing bias
output.
Check if YC8-4 on the engine PWB goes low when maintenance item U101 is run. If not, replace the engine PWB.
Check if YC6-5 on the main PWB goes low when maintenance item U100 is run. If not, replace the main PWB.
Check if YC8-9 on the engine PWB goes low when maintenance item U101 is run. If not, replace the engine PWB.
Causes
No main
charging.
Exposure
lamp fails
to light.
1-4-26
Check if YC8-7 on the engine PWB goes low when maintenance item U100 is run. If not, replace the engine PWB.
Poor contact in the expo- Reinsert the connector. Also check for continuity within the
sure lamp connector ter- connector cable. If none, remedy or replace the cable.
minals.
Defective inverter PWB.
Check if YC16-4 on the engine PWB goes low when maintenance item U061 is run. If not, replace the engine PWB.
2KJ/2KH
(3) Image is too light.
Copy example
Causes
Insufficient toner.
If the display shows the message requesting toner replenishment, replace the container.
Defective
transfer
charging
output.
Check if YC8-4 on the engine PWB goes low when maintenance item U101 is run. If not, replace the engine PWB.
Causes
Replace the high voltage PWB and check for correct operation.
Causes
1-4-27
2KJ/2KH
(6) A black line appears longitudinally.
Copy example
Causes
Clean the drum or, if it is flawed, replace the drum unit (see
page 1-5-41).
Causes
Clean the drum or, if it is flawed, replace the drum unit (see
page 1-5-41).
(8) One side of the copy image is darker than the other.
Copy example
Causes
1-4-28
Causes
Clean the drum or, if it is flawed, replace the drum unit (see
page 1-5-41).
2KJ/2KH
(10) Image is blurred.
Copy example
Causes
(11) The leading edge of the image is consistently misaligned with the original.
Copy example
Causes
Misadjusted leading edge registration. Run maintenance mode U034 to readjust the leading edge
registration (see page 1-3-12).
Misadjusted scanner leading edge
registration.
Run maintenance mode U066 to readjust the scanner leading edge registration (see page 1-3-19).
(12) The leading edge of the image is sporadically misaligned with the original.
Copy example
Causes
Paper feed clutch, MP solenoid or
registration clutch installed or operating incorrectly.
Causes
Paper curled.
Paper damp.
Defective separation.
1-4-29
2KJ/2KH
(14) Offset occurs.
Copy example
Causes
Causes
Paper damp.
Paper creased.
Clean the drum or, if it is flawed, replace the drum unit (see
page 1-5-41).
Causes
1-4-30
Causes
Drum condensation.
2KJ/2KH
(18) Image center does not align with the original center.
Copy example
Causes
1-4-31
2KJ/2KH
1-4-4
Electric problems
Causes
Check the contact between the power plug and the outlet.
2. No electricity at the
power outlet.
Check for continuity across the contacts. If none, replace the main
power switch.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check if the rollers and gears rotate smoothly. If not, grease the
bushings and gears. Check for broken gears and replace if any.
Run maintenance item U030 and check if the eject motor operates. If not, replace the eject motor.
Run maintenance item U030 and check if the eject motor operates. If not, replace the engine PWB.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check if the rollers and gears rotate smoothly. If not, grease the
bushings and gears. Check for broken gears and replace if any.
Run maintenance item U030 and check if the cassette drive motor
operates. If not, replace the cassette drive motor.
Run maintenance item U030 and check if the cassette drive motor
operates. If not, replace the cassette main PWB.
(4)
The scanner motor or
cooling fan motor 1, 2
does not operate.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check for continuity across the coil. If none, replace the motor.
(5)
The paper feed
clutch, registration
clutch or duplex feed
clutch does not operate.
Check for continuity across the coil. If none, replace the clutch.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
(2)
The eject motor does
not operate.
(3)
The cassette drive
motor does not operate.
1-4-32
2KJ/2KH
Problem
(6)
The MP solenoid
does not operate.
(7)
The cleaning lamp
does not turn on.
(8)
The exposure lamp
does not turn on or
off.
Causes
Check for continuity across the coil. If none, replace the solenoid.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
2. Defective exposure lamp. Run maintenance item U061 and check if the exposure lamp turns
on with YC2-1 and YC2-4 on the inverter PCB go low. If not,
replace the exposure lamp.
3. Defective inverter PWB.
Run maintenance item U061 and check if the exposure lamp turns
on with YC1-3 on the inverter PWB go low. If not, replace the
inverter PWB.
If the exposure lamp does not turn off with YC1-3 on the inverter
PWB high, replace the inverter PWB.
(9)
Main charging is not
performed.
(10)
No developing bias is
output.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check if main charging takes place when CN1-7 on the high voltage PWB goes low while maintenance item U100 is run. If not,
replace the high voltage PWB.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check if developing bias is output when CN1-9 on the high voltage PWB goes low while maintenance item U101 is run. If not,
replace the high voltage PWB.
1-4-33
2KJ/2KH
Problem
(11)
Transfer charging is
not performed.
(12)
The original size is
not detected correctly.
Causes
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
1. Original is not placed cor- Check the original and correct if necessary.
rectly.
2. Poor contact in the original detection switch or
original size detection
sensor connector terminals.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
If the level of YC5-B8 on the engine PWB does not go low when
the original detection switch is turned on and off, replace the original detection switch.
(13)
The message
requesting paper to
be loaded is shown
when paper is
present on the cassette or MP tray.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
If the level of following terminal on PWB does not go low when the
switch is turned on and off, replace the switch.
Paper switch: YC2-2 on the cassette PWB
MP paper switch: YC5-12 on the cassette PWB
(14)
The size of paper on
the cassette or MP
tray is not displayed
correctly.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
If the level of following terminal on PWB does not go low when the
switch is turned on and off, replace the switch.
Paper size length switch: YC9-B3, B4, B6 on the engine PWB
MP paper size width switch: YC5-2 on the cassette PWB
(15)
1. A piece of paper torn
A paper jam in the
from copy paper is
paper feed, paper
caught around registraconveying, eject or
tion switch, eject switch
duplex section is indior duplex paper conveycated when the main
ing switch.
power switch is
2. Defective switch.
turned on.
1-4-34
Run maintenance item U031 and turn switch on and off manually.
Replace the switch if indication of the corresponding switch is not
light.
Registration switch, eject switch, duplex paper conveying switch
2KJ/2KH
Problem
Causes
(16)
The message
requesting cover to
be closed is displayed when the front
cover or left cover is
closed.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
(17)
Others.
1-4-35
2KJ/2KH
1-4-5
Mechanical problems
Problem
(1)
No primary paper feed.
Causes/check procedures
Corrective measures
Check if the MP paper feed pulley or MP sep- Replace the pulley if it is deformed (see
aration pad is deformed.
page 1-5-18).
Electrical problem with the following clutches
and solenoid:
paper feed clutch, registration clutch and MP
solenoid.
(2)
No secondary paper
feed.
Check if the surfaces of the right and left registration rollers are dirty with paper powder.
(3)
Skewed paper feed.
Repair or replace.
(4)
The scanner does not
travel.
(5)
Multiple sheets of paper
are fed at one time.
(6)
Paper jams.
(7)
Toner drops on the paper
conveying path.
1-4-36
Check if the developing unit is extremely dirty. Clean the developing unit.
2KJ/2KH
Problem
Causes/check procedures
(8)
Check if the pulleys, rollers and gears operate
Abnormal noise is heard. smoothly.
Check if the following clutches and solenoid
are installed correctly:
paper feed clutch, registration clutch and MP
solenoid.
Corrective measures
Grease the bearings and gears.
Correct.
1-4-37
2KJ/2KH
1-4-38
2KJ/2KH
1-5 Assembly and Disassembly
1-5-1
(1) Precautions
Before starting disassembly, press the Power key on the operation panel to off. Make sure that the Power lamp is off
before turning off the main power switch. And then unplug the power cable from the wall outlet.
Turning off the main power switch before pressing the power key to off may cause damage to the equipped hard disk.
When fax kit is installed, be sure to disconnect the modular code before starting disassembly.
When handling PWBs (printed wiring boards), do not touch parts with bare hands.
The PWBs are susceptible to static charge.
Do not touch any PWB containing ICs with bare hands or any object prone to static charge.
Use only the specified parts to replace the fuser unit thermostat. Never substitute electric wires, as the machine may be
seriously damaged.
When removing the hook of the connector, be sure to release the hook.
Take care not to get the cables caught.
To reassemble the parts, use the original screws. If the types and the sizes of screws are not known, refer to the PARTS
LIST.
(2) Drum
Note the following when handling or storing the drum.
When removing the drum unit, never expose the drum surface to strong direct light.
Keep the drum at an ambient temperature between -20C/-4F and 40C/104F and at a relative humidity not higher than
90% RH. Avoid abrupt changes in temperature and humidity.
Avoid exposure to any substance which is harmful to or may affect the quality of the drum.
Do not touch the drum surface with any object. Should it be touched by hands or stained with oil, clean it.
(3) Toner
Store the toner container in a cool, dark place.
Avoid direct light and high humidity.
1-5-1
2KJ/2KH-1
(4) How to tell a genuine Kyocera Mita toner container
As a means of brand protection, the Kyocera Mita toner container utilizes an optical security technology to enable visual
validation. A validation viewer is required to accomplish this.
Hold the validation viewer over the left side part of the brand protection seal on the toner container. Through each window
of the validation viewer, the left side part of the seal should be seen as follows:
A black-colored band when seen through the left side window
A shiny or gold-colored band when seen through the right side window
The above will reveal that the toner container is a genuine Kyocera Mita branded toner container, otherwise, it is a counterfeit.
Validation viewer
Brand
protection
seal
Brand
protection
seal
Figure 1-5-1
The brand protection seal has an incision as shown below to prohibit reuse.
Incision
Cut
Figure 1-5-2
1-5-2
2KJ/2KH
1-5-2
Cassette
Figure 1-5-3
Screw
Front left
lower cover
Figure 1-5-4
1-5-3
2KJ/2KH
Screw
Figure 1-5-5
5. Release two hooks and remove the separation pulley unit from the lower paper feed
unit.
Hook
Hook
Figure 1-5-6
1-5-4
2KJ/2KH
Separation pulley
Figure 1-5-7
1-5-5
2KJ/2KH
(2) Detaching and refitting the forwarding pulley and paper feed pulley
Follow the procedure below to replace the forwarding pulley and paper feed pulley.
Procedure
1. Remove the lower paper feed unit (see page
1-5-3).
2. Remove the drum unit (see page 1-5-41).
3. Remove five screws and remove the rear
cover.
Screw
Screw
Screw
Screw
Screw
Rear cover
Figure 1-5-8
Bush
Stop ring
Paper feed clutch
Figure 1-5-9
1-5-6
2KJ/2KH
Registration guide
Screw
Figure 1-5-10
Screw
Figure 1-5-11
1-5-7
2KJ/2KH
Shaft holder
Spring
Spring
Bush
Stop ring
Figure 1-5-12
Collar
Paper feed
pulley shaft
Forwarding pulley
Figure 1-5-13
1-5-8
2KJ/2KH
(3) Detaching and refitting the feed roller (22 ppm model only)
Follow the procedure below to replace the feed roller.
Procedure
1. Remove the front left lower cover (see page
1-5-3).
2. Remove three cover labels.
3. Remove five screws and remove the main
body from paper feeder.
Screw
Screw
Cover label
Screw
Screw
Screw
Cover label
Cover label
Paper feeder
Figure 1-5-14
1-5-9
2KJ/2KH
Stop ring
Bush
Feed roller
Figure 1-5-15
Spring pin
Gear
Bush
Feed roller
Bush
Figure 1-5-16
1-5-10
2KJ/2KH
(4) Detaching and refitting the cassette separation pulley (22 ppm model only)
Follow the procedure below to replace the cassette separation pulley.
Procedure
1. Open the front cover and left cover.
2. Pull out the cassette.
3. Remove the screw and remove the lower
paper feed unit.
Screw
Figure 1-5-17
4. Release two hooks and remove the separation pulley unit from the lower paper feed
unit.
Hook
Hook
Figure 1-5-18
1-5-11
2KJ/2KH
Figure 1-5-19
1-5-12
2KJ/2KH
(5) Detaching and refitting the cassette forwarding pulley and cassette paper feed pulley (22 ppm model only)
Follow the procedure below to replace the cassette forwarding pulley and cassette paper feed pulley.
Procedure
1. Remove the feed roller (see page 1-5-9).
2. Remove the lower paper feed unit (see page
1-5-11).
3. Remove the screw and the pin and then
remove the cassette rear cover.
Cassette rear cover
Screw
Pin
Figure 1-5-20
Bush
Stop ring
Stop ring
Cassette paper
feed clutch
Figure 1-5-21
1-5-13
2KJ/2KH
Screw
Figure 1-5-22
Shaft holder
Spring
Spring
Bush
Stop ring
Figure 1-5-23
1-5-14
2KJ/2KH
Collar
Figure 1-5-24
1-5-15
2KJ/2KH
(6) Detaching and refitting the paper conveying unit
Follow the procedure below to maintenance of the paper feed section.
Procedure
1. Remove the drum unit (see page 1-5-41).
2. Remove the lower paper feed unit (see page
1-5-11).
3. Remove the stop ring and strap from the
rear side of the left cover.
Remove the stop ring and stopper from the
front side of the left cover.
Stop ring
Strap
Stop ring
Stopper
Figure 1-5-25
1-5-16
2KJ/2KH
Left cover
Figure 1-5-26
1-5-17
2KJ/2KH
(7) Detaching and refitting the MP paper feed pulley and MP separation pad
Follow the procedure below to replace the MP paper feed pulley and MP separation pad.
Procedure
1. Open the front cover and remove the waste
toner box. Pull out the cassette.
2. Remove the screw and remove the front left
lower cover (see page 1-5-3).
3. Remove the paper conveying unit (see page
1-5-16).
4. Remove the stop ring and bush from the
front side of the machine.
Bush
Stop ring
Figure 1-5-27
MP drive unit
Screw
Screws
Figure 1-5-28
1-5-18
2KJ/2KH
Bush
Gear
Stop ring
Figure 1-5-29
Figure 1-5-30
1-5-19
2KJ/2KH-1
Spring pin
MP paper guide
Stop ring
Figure 1-5-31
MP separation pad
MP separation pad
Figure 1-5-32
1-5-20
2KJ/2KH
(8) Detaching and refitting the left registration roller
Follow the procedure below to replace the left registration roller.
Procedure
1. Remove the paper conveying unit (see page
1-5-16).
2. Release the stoppers at the front and rear
side, and then remove the left registration
roller from the paper conveying unit.
Stopper
Figure 1-5-33
Gear
Stopper
Bush
Bush
Stopper
Figure 1-5-34
1-5-21
2KJ/2KH
(9) Detaching and refitting the right registration roller
Follow the procedure below to replace the right registration roller.
Procedure
1. Remove the drum unit (see page 1-5-41).
2. Remove the rear cover (see page 1-5-6).
3. Remove the connector and remove the registration clutch.
Registration clutch
Figure 1-5-35
Figure 1-5-36
1-5-22
2KJ/2KH
Bush
Gear
Bush
Figure 1-5-37
1-5-23
2KJ/2KH
1-5-3
Optical section
Screw
Right upper cover
Screw
Contact glass
Figure 1-5-38
3. Open the front cover and left cover.
4. Remove the front left cover (see page 1-547).
5. Release five hooks and both and then
remove the front scanner cover.
6. Remove two screws and remove the rear
upper cover.
Screw
Rear upper cover
Screw
Hook
\
Hook
Hook
Both
Hook
Figure 1-5-39
1-5-24
2KJ/2KH
Film
Film
Mirror 1 frame
Figure 1-5-40
9. Remove the connector of the exposure lamp
from inverter PWB and remove the lamp
wire from ribs.
Connector
Lamp wire
Inverter PWB
Figure 1-5-41
10. Remove two screws and remove the exposure lamp.
11. Replace the exposure lamp and refit all the
removed parts.
Screw
Exposure lamp
Screw
Figure 1-5-42
1-5-25
2KJ/2KH
(2) Detaching and refitting the scanner wires
Take the following procedure when the scanner wires are broken or to be replaced.
(2-1) Detaching the scanner wires
Procedure
1. Remove the exposure lamp (see page 1-524).
2. Open the left cover.
3. Release six hooks and both and then
remove the left middle cover.
Hook
Hook
Hook
Hook
Hook
Hook
Figure 1-5-43
4. Release five hooks and two bothes and then
remove the left upper cover.
Left upper cover
Both
Hook
Both
Hook
Hook
Hook
Hook
Figure 1-5-44
1-5-26
2KJ/2KH
Screw
Slit glass
Slit retainer
Figure 1-5-45
Inverter wire
Inverter PWB
Wire guide
Wire guide
Figure 1-5-46
1-5-27
2KJ/2KH
Mirror 1 frame
Screw
Screw
Front wire
retainer
Rear wire
retainer
Figure 1-5-47
Round terminal
Round terminal
Figure 1-5-48
1-5-28
2KJ/2KH
(2-2) Fitting the scanner wires
NOTE
When fitting the wires, be sure to use those specified below.
Machine front: (P/N: 2C91236), gray
Machine rear: (P/N: 2C91235), black
Fitting requires the following tools
Two frame securing tools (P/N 302C968310)
Two scanner wire stoppers (P/N 3596811)
Procedure
1. Remove the rear cover.
Right middle cover
Screw
Screw
Right middle cover
Hook
Both
Both
Hook
Figure 1-5-49
Screw
Bush
Stop ring
Scanner wire
drum gear
Figure 1-5-50
1-5-29
2KJ/2KH
Bush
Stop ring
Figure 1-5-51
6. Insert the locating ball on each of the scanner wires into the hole in the respective
scanner wire drum and wind the scanner
wire three turns inward and four turns outward.
With the locating ball as the reference point,
wind the shorter end of each of the wires
outward.
7. Secure the scanner wires using the scanner
wire stoppers.
Scanner wire
stopper
Scanner wire
stopper
Three turns
inward
Three turns
inward
Scanner wire
drum
Four turns
outward
Locating ball
Figure 1-5-52
1-5-30
Four turns
outward
2KJ/2KH
Mirror 2 frame
Figure 1-5-53
10. Loop the outer ends of the scanner wires around the outer grooves in the pulleys on the mirror 2 frame,
winding from below to above. .......................................................................................................................... (1)
11. Hook the round terminals onto the catches inside the scanner unit. ............................................................... (2)
12. Loop the inner ends of the scanner wires around the grooves in the pulleys at the left of the scanner unit,
winding from below to above. .......................................................................................................................... (3)
13. Loop the scanner wires around the inner grooves in the pulleys on the mirror 2 frame, winding from
above to below................................................................................................................................................. (4)
14. Wind the scanner wires around the grooves in the scanner wire guides at the left of the scanner unit. ......... (5)
15. Hook the round terminals onto the scanner wire springs................................................................................. (6)
Figure 1-5-54
1-5-31
2KJ/2KH
Mirror 2 frame
Mirror 1 frame
Figure 1-5-55
1-5-32
2KJ/2KH
(3) Detaching and refitting the ISU (reference)
Follow the procedure below to replace the ISU.
Procedure
1. Remove the contact glass (see page 1-524).
2. Remove four screws and remove the ISU
cover.
Screws
ISU cover
Screws
Figure 1-5-56
CCD PWB
CCD wire
Figure 1-5-57
1-5-33
2KJ/2KH
4.
5.
6.
7.
Screw
Screw
Plate
Screws
Plate
ISU
Figure 1-5-58
1-5-34
2KJ/2KH
(4) Detaching and refitting the laser scanner unit
Follow the procedure below to replace the laser scanner unit.
Procedure
1. Remove the original cover or the document
processor.
2. Remove the rear cover (see page 1-5-6).
Remove the front left cover (see page 1-547).
Remove the right upper cover, contact
glass, rear upper cover and front scanner
cover (see page 1-5-24).
Remove the left middle cover, left upper
cover and slit glass (see page 1-5-26).
Remove the right middle cover (see page 15-29).
3. Remove the screw and release three hooks
and then remove the front right cover.
Screw
Front right
cover
Hook
Hook
Hook
Figure 1-5-59
1-5-35
2KJ/2KH
Screw
Screw
Hook
Right lower
cover
Hook
Both
Both
Hook
Hook
Hook
Hook
Figure 1-5-60
Screw
Shield cover
Screw
Figure 1-5-61
1-5-36
2KJ/2KH
YC5
YC15
YC16
YC5
Engine PWB
Main PWB
Figure 1-5-62
Pin
Scanner unit
Pin
Pin
Pin
Figure 1-5-63
1-5-37
2KJ/2KH
Screw
Figure 1-5-64
Screw
Figure 1-5-65
1-5-38
2KJ/2KH
Both
Hook
Hook
Eject tray
Figure 1-5-66
12. Remove four screws and two connectors
and remove the laser scanner unit.
13. Replace the laser scanner unit and refit all
the removed parts.
Connector
Screw
Screw
Screw
Screw
Laser scanner
unit
Connector
Figure 1-5-67
1-5-39
2KJ/2KH
(5) Adjusting the longitudinal squareness (reference)
Perform the following adjustment if the leading and trailing edges of the copy image are laterally skewed (lateral squareness not obtained).
Caution:
Adjust the deflection in the paper at the registration roller first (see page 1-3-15). Check for the longitudinal squareness of
the copy image, and if it is not obtained, perform the longitudinal squareness adjustment.
Before making the following adjustment, output a VTC-PG2 pattern in maintenance item U993 to use as the original for the
adjustment.
Procedure
Start
Yes
No
End
Original
Copy
example 1
Copy
example 2
Figure 1-5-68
Screws
Figure 1-5-69
1-5-40
2KJ/2KH
1-5-4
Drum section
Screw
Figure 1-5-70
4. Remove the screw and the connector and
then remove the drum unit.
5. Replace the drum unit and refit all the
removed parts.
6. when the periodic maintenance, perform
maintenance mode U251 (clearing the
maintenance count) (see page 1-3-45).
Connector
Drum unit
Screw
Figure 1-5-71
1-5-41
2KJ/2KH
(2) Detaching and refitting the drum separation claws
Follow the procedure below to replace the drum separation claws.
Cautions
Avoid direct sunlight or strong light when detaching and refitting the drum unit.
Never touch the drum surface when holding the drum unit.
Procedure
1. Remove the drum unit (see page 1-5-41).
2. Push the drum separation claws with the
minus driver from the top of the hole and
remove the claws.
3. Replace the drum separation claws and refit
all the removed parts.
Hole
Drum
separation
claw
Drum
separation
claw
Drum
separation
claw
Drum
separation
claw
Figure 1-5-72
1-5-42
2KJ/2KH
(3) Detaching and refitting the main charger unit
Follow the procedure below to replace the main charger unit.
Procedure
1. Open the front cover and remove the waste
toner box.
2. While lifting the main charger unit toward the
upper right, remove the unit.
3. While pressing the main charger release
lever in the direction indicated by the arrow
at the removal stopper position to release
the removal stopper, remove the main
charger unit from the machine.
4. Replace the main charger unit and refit all
the removed parts.
Main charger
release lever
Figure 1-5-73
1-5-43
2KJ/2KH
1-5-5
Developing section
Developing unit
Figure 1-5-74
1-5-44
2KJ/2KH
1-5-6
Transfer section
Inserted part
Figure 1-5-75
3. Remove two collars A, two collars B, gear,
two stoppers and two bushes from transfer
roller.
Collar B
Bush
Collar A
Gear
Stopper
Transfer roller
Stopper
Collar B
Collar A
Bush
Figure 1-5-76
1-5-45
2KJ/2KH
Protrusion
Transfer spring
Transfer spring
Figure 1-5-77
1-5-46
2KJ/2KH
1-5-7
Fuser section
Caution
Inserted part
Inserted part
Screw
Figure 1-5-78
Connectors
Screw
Fuser unit
Figure 1-5-79
1-5-47
2KJ/2KH
Notch position
Hook
Fuser thermistor wire
Figure 1-5-80
1-5-48
2KJ/2KH
(2) Detaching and refitting the press roller
Follow the procedure below to replace the press roller.
Procedure
1. Remove the fuser unit (see page 1-5-47).
2. Remove two screws and open the fuser unit.
3. Separate the right and left fuser unit.
Screw
Screw
Fuser unit
Figure 1-5-81
4. Remove the screw and release two hooks
and then remove the press roller guide from
the left fuser unit.
Hook
Screw
Figure 1-5-82
1-5-49
2KJ/2KH
Press roller
Bush
Figure 1-5-83
1-5-50
2KJ/2KH
(3) Detaching and refitting the fuser heater
Follow the procedure below to replace the fuser heater.
Procedure
1. Remove the fuser unit (see page 1-5-47).
2. Remove two positive terminals of fuser
heater wires from the fuser unit.
Caution
Remove the positive terminals while pressing their protrusions.
3. Remove two fuser heater wires from ribs of
the fuser unit.
Caution
Make sure that the fuser heater wires are
not removed from the positive terminals.
Protrusion
Fuser unit
Positive terminal
Fuser heater wire
Positive terminal
Figure 1-5-84
Figure 1-5-85
1-5-51
2KJ/2KH
Fuser heater
Hook
Figure 1-5-86
Hook
Hook
Protrusion
Front side
Figure 1-5-87
1-5-52
2KJ/2KH
Fuser heater
wire
Figure 1-5-88
12. Connect front and rear positive terminal to
thermostats.
Cautions
Insert the terminal all the way into the unit.
Put the slack of electric wire toward the front
side of the machine.
Push each terminal and heater wire into the
housing so as not to exceed the height of
the rib of the fuser unit (because they may
come in contact with the machine frame at
the time of installation of the machine).
To front
Positive terminal
Rib
Fuser heater wire
To front
Figure 1-5-89
1-5-53
2KJ/2KH
(4) Detaching and refitting the heat roller separation claws
Follow the procedure below to replace the heat roller separation claws.
Procedure
1. Separate the right and left fuser unit (see
page 1-5-49).
2. Release four hooks and remove the fuser
guide from the right fuser unit.
Hook
Hook
Hook
Figure 1-5-90
Heat roller
separation claw
Spring
Heat roller
separation claws
Right fuser unit
Figure 1-5-91
1-5-54
2KJ/2KH
(5) Detaching and refitting the heat roller
Follow the procedure below to replace the heat roller.
Procedure
1. Separate the right and left fuser unit (see
page 1-5-49).
2. Remove the fuser heater (see page 1-5-51).
3. Remove the heat roller separation claws
(see page 1-5-54).
4. Press the heat roller bush in the rear side of
the right fuser unit from outside to make the
roller removable.
Figure 1-5-92
Heat roller
Heat
roller bush
Heat
roller gear
Figure 1-5-93
1-5-55
2KJ/2KH
Fuser thermistor
Fuser thermostat
Fuser thermostat
Idle gear
Figure 1-5-94
1-5-56
2KJ/2KH
(6) Detaching and refitting the fuser thermistor
Follow the procedure below to replace the fuser thermistor.
Procedure
1. Separate the right and left fuser unit (see
page 1-5-49).
2. Remove the heat roller (see page 1-5-55).
3. Remove the screw and remove the fuser
thermistor.
4. Replace the fuser thermistor and refit all the
removed parts.
Caution
Restore the fuser thermistor wire to its original correct position.
After refitting the heat roller, push the roller
lightly to check that the detection surface of
the fuser thermistor comes in contact with
the roller.
Screw
Fuser thermistor
Figure 1-5-95
1-5-57
2KJ/2KH
(7) Detaching and refitting the fuser thermostat
Follow the procedure below to replace the fuser thermostat.
Cautions
Be sure to replace it after finding the cause of failure.
If the cause is not found, do not replace only the component in question but the entire unit.
If C6000 or C6020 occurs, replace the thermostat after resolving the problem.
Before replacement, conduct continuity check for the thermostat.
Procedure
1. Remove the fuser unit (see page 1-5-47).
2. Remove two positive terminals from fuser
thermostat.
3. Remove two screws and remove the fuser
thermostat.
4. Replace the fuser thermostat and refit all the
removed parts.
Cautions
Insert the terminal all the way into the unit.
Put the slack of electric wire toward the front
side of the machine.
Push each terminal and heater wire into the
housing so as not to exceed the height of
the rib of the fuser unit (because they may
come in contact with the machine frame at
the time of installation of the machine).
Screw
Screw
Fuser thermostat
Positive terminal
Positive terminal
Figure 1-5-96
0.7 to 1.5 mm
Figure 1-5-97
1-5-58
2KJ/2KH
(8) Adjusting front position of the fuser unit (adjusting lateral squareness)
Follow the procedure below if the drum is not parallel to the fuser unit and therefore paper is not fed straight to the fuser
section and the trailing edge of image on either the front or rear side becomes longer.
Procedure
Start
Yes
End
No
Original
Copy
example 1
Copy
example 2
Figure 1-5-98
Screw
Adjusting spacer
Fuser unit
Figure 1-5-99
1-5-59
2KJ/2KH
1-5-8
Others
YC14
Rib
Connector
Rib
Clamp
Engine PWB
Figure 1-5-100
Screw
Eject unit
Inserted part
Figure 1-5-101
1-5-60
2KJ/2KH
Eject unit
Figure 1-5-102
1-5-61
2KJ/2KH
(2) Direction of installing the principal fan motors
When detaching or refitting the cooling fan motor 1 or 2, be careful of the airflow direction (intake or exhaust).
Exhaust
Intake
Figure 1-5-103
1-5-62
2KJ/2KH
1-6 Requirements on PWB Replacement
1-6-1
Follow the procedure below to upgrade the firmware of main, engine and MMI.
Firmware upgrading requires the following tools:
Compact Flash (Products manufactured by SANDISK are recommended.)
NOTE
When writing data to a new Compact Flash from a computer, be sure to format it in advance.
Procedure
1. Perform maintenance item U000 (maintenance report output) and check U019 ROM
version.
2. Press the power key on the operation panel
to off. Make sure that the Power lamp is off
before turning off the main power switch.
And then unplug the power cable from the
wall outlet.
3. Remove the screw and remove the slot
cover.
4. Insert Compact Flash in a notch hole of the
machine.
Insert the surface of Compact Flash toward
the machine rear.
5. Insert the power plug and turn the main
power switch on. Upgrading firmware starts.
Caution:
Never turn the main power switch off during
upgrading.
Compact Flash
Screw
Slot cover
Figure 1-6-1
6. [Completed] is displayed on the touch panel
when upgrading is complete.
7. Turn the main power switch off and unplug
the power cable from the wall outlet.
8. Remove Compact Flash from the machine.
9. Refit the slot cover.
10. Insert the power plug and turn the main
power switch on.
11. Perform maintenance item U000 (maintenance report output) and check that U019
ROM version has been upgraded.
1-6-1
2KJ/2KH
1-6-2
The variable resistors listed below are set at the factory prior to shipping and cannot be adjusted in the field.
High voltage PWB: VR401
APC PWB: VR1
1-6-3
When replacing the main PWB or engine PWB, remove the EEPROM (YS3) or EEPROM (U3) from the PWB that has
been removed and then reattach it to the new PWB.
EEPROM
Main PWB
EEPROM
(YS3)
EEPROM
(U3)
Engine PWB
EEPROM
Figure 1-6-2
1-6-2
2KJ/2KH
2-1 Mechanical construction
2-1-1
The paper feed section conveys paper from the cassette (one cassette is standard for 18 ppm model/two cassettes are
standard for 22 ppm model) or MP tray to the left and right registration rollers, at which point secondary feed takes place
and the paper travels to the transfer section in sync with the printing timing.
Cassette can hold up to 300 (80 g/m2) sheets of paper. Paper is fed from the cassette by the rotation of the forwarding pulley and paper feed pulley. The separation pulley prevents multiple sheets from being fed at one time, via the torque limiter.
The MP tray can hold up to 100 (80 g/m2) sheets of paper. Paper is fed from the MP tray by the rotation of the MP paper
feed pulley.
1
4
5
10
11
3
6
17
18
14
13
12
16
19
20
15
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
Forwarding pulley
Paper feed pulley
Separation pulley
Cassette base
MP paper feed pulley
MP separation pad
Left registration roller
Right registration roller
Registration switch (RSW)
Paper switch (PSW)
MP paper switch (MPPSW)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
2-1-1
2KJ/2KH
REGCLM
RCL
YC6-2
CPWB
RSW
PFCL
PSW
C1PDSWN
FCLTN
REGSW
BPWSW
MPPWSW
BPPESW
MPPSW
CPFCL
YC2-2
YC7-2
YC5-10
YC5-12
YC5-2
CPSW
YC1
PE
CFSW
YC7
YC5-2
EPWB
CMPWB
CLT_RE
FEED
YC8-2
YC3
YC6-2
2-1-2
YC9
2KJ/2KH
2-1-2
Optical section
The optical section consists of the image scanner section for scanning and the laser scanner section for printing.
(1) Image scanner section
The original image is illuminated by the exposure lamp (EL) and scanned by the CCD PWB (CCDPWB) in the image scanning unit via the three mirrors, the reflected light being converted to an electrical signal.
The scanner and mirror frames travel to scan on the optical rails on the front and rear of the machine to scan from side to
side. The speed of the mirror frames is half the speed of the scanner.
When the DP is used, the scanner and mirror frames stop at the DP original scanning position to start scanning.
12
13
1
3
11
10
14
15
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Mirror 1 frame
Exposure lamp (EL)
Mirror 1
Scanner reflector
Mirror 2 frame
Mirror 2
Mirror 3
ISU
(9)
(10)
(11)
(12)
(13)
(14)
(15)
2-1-3
2KJ/2KH
Original
HPSW
EL
ODSW
OSDS
SM
Lens
CCDPWB
Reading
image data
HPSWN
CCD image
sensor
YC5-B5
INPWB
YC16-4
YC5-B8
YC1
LAMPN
YC5
OPSWN
Serial communication
data signal
MPWB
YC7
EPWB
YC5-B2
YC15-1
YC15-2
YC15-3
YC15-4
ORGLSWN
ISMDA
ISMDB
ISMDNA
ISMDNB
2-1-4
2KJ/2KH
(2) Laser scanner section
The image data scanned by the CCD PWB (CCDPWB) is processed on the main PWB (MPWB) and transmitted as image
printing data to the laser scanner unit (LSU). By repeatedly turning the laser on and off, the laser scanner unit forms a
latent image on the drum surface.
10
7
9
6
5
8
3
2
4
1
Figure 2-1-5 Laser scanner section
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
2-1-5
2KJ/2KH
Laser scanner
unit (LSU)
PDPWB
PM
PLGCLKN
PLGRDYN
Drum
Polygon
mirror
PLGDRN
YC3-A1
YC3-A2
YC3-A3
Serial communication
data signal
YC1
EPWB
Laser diode
YC7
APCPWB
PDN
OUTPEN
SAMPLEN
VDON
VDOP
2-1-6
YC6-1
YC6-3
YC6-4
YC6-5
YC6-6
MPWB
2KJ/2KH
2-1-3
Drum section
The drum section consists of the drum, main charger section, cleaning section and cleaning lamp.
The main charger section consists of main charger wire and main charger grid, and the drum is charged by a high voltage
applied to the main charger wire.
The cleaning section consists of the cleaning blade and cleaning roller that removes residual toner from the drum surface
after the transfer process, and the cleaning spiral that carries the residual toner back to the waste toner box.
The cleaning lamp (CL) consists of LEDs which remove residual charge from the drum surface.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
Drum
Drum separation claws
Main charger unit
Main charger wire
Main charger grid
Cleaning roller
Cleaning spiral
Cleaning blade
Cleaning lamp (CL)
2-1-7
2KJ/2KH
ERASE2N
ERASE1N
CL
Main charging
high voltage
CN1-7
MHVDRN
HVTPWB
YC3-B6
YC3-B7
YC8-7
EPWB
Grid
Drum
OFS
TONEFULL
YC3-B2
Zener PWB
DRM
2-1-8
DDMREM
YC6-11
2KJ/2KH
2-1-4
Developing section
The developing section consists of the developing unit and the toner container.
The developing unit consists of the developing sleeve where a magnetic brush is formed, the magnetic toner blade and
the developing spirals that agitate the toner.
Also, the toner container sensor (TCS) checks whether or not toner remains in the toner container.
7
Figure 2-1-9 Developing section
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Developing unit
Developing sleeve
Magnetic toner blade
Left developing spiral
Right developing spiral
Toner container
Toner container sensor (TCS)
Toner container detection switch (TCDSW)
2-1-9
2KJ/2KH
Drum
EPWB
HVTPWB
Developing
sleeve
Developing bias
CN1-9
TCDSW
DHVCLKC
TCONDET
YC8-9
YC9-B7
YC7
YC1
TCS
TONEPY
YC3-2
CPWB
2-1-10
2KJ/2KH
(1) Single component developing system
This machine uses the single component developing system, and reversal processing is performed with a + charged drum
and a + charged magnetic toner.
With the single component developing system, toner is electrically charged by friction with the developing sleeve and +
charged when it passes through the magnetic toner blade. The toner that has passed through the magnetic toner blade
forms a uniform layer on the developing sleeve. When the toner layer comes to the location where the developing sleeve
is the nearest to the drum, toner moves between the drum and the developing sleeve by an electric field of the magnetic
pole. Then, when the developing sleeve rotates and passes through the nearest location to the drum, on the portion of the
drum that has been exposed to light, toner is attracted toward the drum by potential difference between the developing
bias and the drum surface and development is performed. On the other hand, on the portion of the drum that has not been
exposed to light, toner is attracted toward the sleeve and development is not performed. When toner comes to an area
where the gap between the drum and the developing sleeve is large, an electric field disappears and toner does not leave
the developing sleeve. Development is complete.
Toner
South pole
Drum
North pole
Developing sleeve
2-1-11
2KJ/2KH
2-1-5
The transfer and separation sections consists of the transfer roller, separation electrode and drum separation claws.
A high voltage generated by the high voltage PWB (HVTPWB) is applied to the transfer roller for transfer charging.
Paper after transfer is separated from the drum by applying separation bias that is output from the high voltage PWB
(HVTPWB) to the separation electrode.
3
2
(1)
(2)
(3)
(4)
EPWB
YC8-6
YC8-8
YC8-3
YC8-4
Transfer roller
Separation electrode
Drum separation claw
Drum
HVTPWB
SHVDRN
SHVISELN
THVADJC
THVDRN
CN1-6
CN1-8
CN1-3
Separation
high voltage
Separation
electrode
Transfe
high voltage
Drum
CN1-4
Transfer roller
2-1-12
2KJ/2KH
2-1-6
Fuser section
The fuser section consists of the parts shown in figure. When paper reaches the fuser section after the transfer process it
passes between the press roller and heat roller, which is heated by fuser heaters M and S (FH-M/S). Pressure is applied
by the fuser unit pressure springs so that the toner on the paper is melted, fused and fixed onto the paper.
The heat roller is heated by fuser heaters M and S (FH-M/S) inside it; its surface temperature is detected by the fuser thermistor (FTH) and is regulated by the fuser heaters turning on and off. If the fuser section becomes abnormally hot, fuser
thermostat (FTS) operates shutting the power to the fuser heaters off.
When the fuser process is completed, the paper is separated from the heat roller by its separation claws and is conveyed
to eject and switchback section.
5
2
8
7
9, 10
4
Figure 2-1-14 Fuser section
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
2-1-13
2KJ/2KH
YC3-B9
THERMA
FTH
FH-S
FH-M
FTS1
EPWB
Heat roller
YC18-3
SHREM
YC2-7
2-1-14
LIVE
MH
YC2-5
YC4-3
MHREM
YC4-1
YC18-1
YC4-2
SH
FTS2
PSPWB
2KJ/2KH
2-1-7
The eject and switchback sections eject paper on which fuser has ended with the eject roller that is rotated by forward
rotation of the eject motor.
In duplex copying, paper is turned over by reverse rotation of the eject motor.
.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Feedshift guide
Eject roller
Eject pulley
Switchback roller
Switchback pulley
Feedshift guide
Eject switch (ESW)
Feedshift switch (FSSW)
2-1-15
2KJ/2KH
EPWB
SEPSWN
FSSW
EM
ESW
COMDA
COMDB
COMDNA
COMDNB
EXTSWN
YC14-3
YC13-1
YC13-2
YC13-3
YC13-4
YC14-2
2-1-16
2KJ/2KH
2-1-8
Duplex section
In duplex mode, after copying on to the reverse face of the paper, the paper is reversed in the switchback section and conveyed to the duplex unit. The paper is then conveyed to the paper feed section by the upper and lower duplex feed rollers.
4
5
(1)
(2)
(3)
(4)
(5)
(6)
Feedshift guide
Duplex feed pulley
Upper duplex feed roller
Duplex feed pulley
Lower duplex feed roller
Duplex paper conveying switch (DUPPCSW)
2-1-17
2KJ/2KH
EPWB
YC7
YC1
DUP
PCSW
DUPFCL
IPPSWN
ICLTN
YC5-5
YC5-8
CPWB
2-1-18
2KJ/2KH
2-2 Electrical Parts Layout
2-2-1
(1) PWBs
5
6
1
14
10
9
15
3
16
11
12
Machine front
Machine inside
13
Machine rear
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Engine PWB (EPWB)................................... Controls the other PWBs, electrical components and optional devices.
Main PWB (MPWB) ..................................... Controls the operation panel and laser scanner unit.
Power source PWB (PSPWB) ..................... Generates +24 V DC; controls the fuser heaters.
High voltage PWB (HVTPWB) ..................... Main charging. Generates high voltages for transfer and high voltages for
separation.
Inverter PWB (INPWB) ................................ Controls the exposure lamp.
CCD PWB (CCDPWB)................................. Reads the image of originals.
Operation unit PWB (OPWB)....................... Consists of the operation keys and display LEDs.
LCD PWB (LCDPWB).................................. Controls LCD indication.
APC PWB (APCPWB) ................................. Generates and controls the laser beam.
PD PWB (PDPWB) ...................................... Controls horizontal synchronizing timing of laser beam.
Cassette PWB (CPWB) ............................... Relays wirings from electrical components.
Cassette main PWB (CMPWB)*1.................. Controls electrical components of the paper feeder.
Cassette heater PWB (CHPWB)*1................ Relays the cassette heater power.
Fax control PWB (FCPWB)*2........................ Modulates, demodulates, compresses, decompresses and smoothes out
image data, and converts resolution of image data.
2-2-1
2KJ/2KH
15. NCU PWB (NCUPWB)*2............................... Controls connection to the telephone line.
16. Fax relay PWB (FRPWB)*2........................... Consists of wiring relay circuits between fax control PWB and main PWB.
*1: Option for 18 ppm model/standard for 22 ppm model
*2: Option
PARTS HVU SP
10
PD PWB (PDPWB)
11
12
13
14
15
16
2-2-2
2KJ/2KH
(2) Switches and sensors
8
9
10
13
12
17
24
2
16
15
11
14
18
19
21
20
22
23
Machine front
Machine inside
Machine rear
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Main power switch (MSW) ........................... Turns the AC power on and off.
Front cover safety switch (FCSSW)............. Breaks the safety circuit when the front cover is opened.
Left cover safety switch (LCSSW) ............... Breaks the safety circuit when the left cover is opened.
Paper switch (PSW)..................................... Detects the presence of paper in the cassette.
Paper size length switch (PLSW) ................ Detects the length of paper in the cassette.
Paper size width switch (PWSW)................. Detects the width of paper in the cassette.
MP paper size width switch (MPPWSW) ..... Detects the width of paper on the MP tray.
Home position switch (HPSW)..................... Detects the optical system in the home position.
Original detection switch (ODSW) ............... Operates the original size detection sensor.
Original size detection sensor (OSDS) ........ Detects the size of the original.
Registration switch (RSW) ........................... Controls the secondary paper feed start timing.
Eject switch (ESW) ...................................... Detects a paper misfeed in the fuser section.
Feedshift switch (FSSW) ............................. Detects a paper misfeed in the switchback section in a duplex copy.
Toner container sensor (TCS) ...................... Detects the quantity of toner in a toner container.
Toner container detection switch
(TCDSW) ..................................................... Detects the presence of the toner container.
16. Overflow sensor (OFS) ................................ Detects when the waste toner box is full.
17. Fuser thermistor (FTH) ................................ Detects the heat roller temperature.
2-2-3
2KJ/2KH
18. MP paper switch (MPPSW) ......................... Detects the presence of paper on the MP tray.
19. Cassette left cover safety switch
(CLCSSW)*1 ................................................. Breaks the safety circuit when the cassette left cover is opened.
20. Cassette feed switch (CFSW)*1 .................... Detects a paper misfeed.
21. Cassette paper switch (CPSW)*1 ................. Detects the presence of paper in the cassette.
22. Cassette paper size length switch
(CPLSW)*1 .................................................... Detects the length of paper in the cassette.
23. Cassette paper size width switch
(CPWSW)*1 .................................................. Detects the width of paper in the cassette.
24. Duplex paper conveying switch
(DUPPCSW)*2 .............................................. Detects a paper jam in the duplex section.
*1: Option for 18 ppm model/standard for 22 ppm model
*2: Option
2-2-4
2KJ/2KH
(3) Motors
6
2
Machine front
Machine inside
Machine rear
1.
2.
3.
4.
5.
6.
7.
8.
2-2-5
2KJ/2KH
(4) Others
7
6
8, 9
5
13
2
1
10
12
11
Machine front
Machine inside
Machine rear
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Paper feed clutch (PFCL) ............................ Primary paper feed from the cassette.
Registration clutch (RCL)............................. Secondary paper feed.
MP solenoid (MPSOL) ................................. Primary paper feed from the MP tray.
Exposure lamp (EL) ..................................... Exposes originals.
Cleaning lamp (CL) ...................................... Removes residual charge from the drum surface.
Fuser heater M (FH-M) ................................ Heats the heat roller.
Fuser heater S (FH-S) ................................. Heats the heat roller.
Fuser thermostat 1 (FTS1)........................... Prevents overheating in the fuser section.
Fuser thermostat 2 (FTS2)........................... Prevents overheating in the fuser section.
Cassette heater (CH) ................................... Dehumidifies the cassette section.
Cassette heater (CH)*1 ................................. Dehumidifies the cassette section.
Cassette paper feed clutch (CPFCL)*1 ......... Primary paper feed from the cassette.
Duplex feed clutch (DUPFCL)*2.................... Controls the drive of the duplex feed roller.
2-2-6
2KJ/2KH
2-3 Operation of the PWBs
2-3-1
YC4
YC1
YC2
TB4
TB3
YC3
TB1
TB2
2-3-1
2KJ/2KH
Connector
TB
Pin No.
Signal
I/O
Voltage
Description
AC_LIVE
120 V AC
220-240 V AC
AC power input
Connected
to the AC
inlet and
main power
switch
AC_COM
120 V AC
220-240 V AC
AC power input
LIVE
120 V AC
220-240 V AC
LIVE
120 V AC
220-240 V AC
YC1
GND
Ground
Connected
to the
engine PWB
+24V
24 V DC
+24V
24 V DC
+24V
24 V DC
GND
Ground
GND
Ground
YC2
+24V2
24 V DC
Connected
to the
engine PWB
ZCROSS
RELAYREM
0/3.3 V DC
Relay signal
GND
Ground
SHREM
0/3.3 V DC
FH-S: On/Off
SLEEP
0/3.3 V DC
MHREM
0/3.3 V DC
FH-M: On/Off
LIVE
120 V AC
220-240 V AC
AC power output to CH
LIVE
120 V AC
220-240 V AC
AC power output to CH
NC
Not used
NEUTRAL
120 V AC
220-240 V AC
NEUTRAL
120 V AC
220-240 V AC
MH
120 V AC
220-240 V AC
FH-M: On/Off
SH
120 V AC
220-240 V AC
FH-S: On/Off
LIVE
120 V AC
220-240 V AC
YC3
Connected
to the cassette heater
and paper
feeder
YC4
Connected
to the fuser
heater M/S
2-3-2
2KJ/2KH
2-3-2
Main PWB
13
U58
16
YC16
U63
YC14
B49
B50
A49
A50
U9
U59
U57
11
16
YC15
YC5
U42
U64
YC12
U55
19
YS1
13
YC2
YC4
U24
U29
U4
1
U6 U27 U22
YC13
U54
U52
20
12
U41
YC9
U18
YC3
1
B1
B2
A1
A2
U8
U56
U21
U20
U38
U19
U28 U26 U23
U53
31
30
BAT1
U1 U2
50
U74
U72 U70
YC17
20
U73
YS3
60
U31
U75
U71
26
B2 B1
U51
U50
YC7
A2 A1
1
U66
U7
U65
U45
YS4
U61
YC18
U67
50
25
YC19
U43
U60
U85
YC1
U68
U76
32
U49
U47
U48
U46
U81
YC10
YS2
LED1
U62
LED2
U11
2
U5
YC21
U3
1 10
YC20
31
YC6
YC8 YC22
2-3-3
2KJ/2KH
Connector
Pin No.
YC5
5V
2
3
Connected
to the CCD
PWB
Signal
I/O
Voltage
Description
5 V DC
NC
Not used
TG
0/3.3 V DC
GND
Ground
RS
0/3.3 V DC
GND
Ground
CP
0/3.3 V DC
GND
Ground
PHY2
10
GND
Ground
11
GND
Ground
12
Vout1
Analog
13
Vout2
Analog
14
GND
Ground
15
NC
Not used
16
CCDPWR
12 V DC
PDN
0/3.3 V DC
SGND
Ground
OUTREN
0/3.3 V DC
SAMPLEN
0/3.3 V DC
VDON
VDOP
5V1
5 V DC
YC7
_RST_ENG
0/3.3 V DC
Connected
to the
engine PWB
SCANHLD
0/3.3 V DC
ENGHLD
0/3.3 V DC
AFEOVSYNC
GND
Ground
_24V_DOWN
0/3.3 V DC
PVSYNC
GND
Ground
EGOUTPEN
0/3.3 V DC
10
PLGCLK
YC6
Connected
to the APC
PWB
2-3-4
11
SLEEP
0/3.3 V DC
12
GND
Ground
13
EGSIRN
0/3.3 V DC
14
EGSDIR
0/3.3 V DC
15
GND
Ground
16
EGSBSY
0/3.3 V DC
17
EGSDO_BUF
18
GND
19
EGSCLK_BUF
20
EGSDI
Ground
2KJ/2KH
Connector
Pin No.
Signal
I/O
Voltage
Description
YC8
+5V
5 V DC
Connected
to the
engine PWB
+5V
5 V DC
+5V
5 V DC
GND
Ground
+3.3V
3.3 V DC
+3.3V
3.3 V DC
GND
Ground
GND
Ground
GND
Ground
10
+5V
5 V DC
YC10
GND
Ground
Connected
to the fax
control PWB
(fax relay
PWB)
5V
5 V DC
CLKOUT
5V
5 V DC
GND
Ground
MREOUT
0/3.3 V DC
_HSYNCOUT
0/3.3 V DC
GND
Ground
_VSYNCOUT
0/3.3 V DC
10
_IDOUT
0/3.3 V DC
11
GND
Ground
Ground
12
GND
13
TXD
14
_STS
0/3.3 V DC
15
_MAIN_STS
0/3.3 V DC
16
FAXDOWN
0/3.3 V DC
17
MREIN
0/3.3 V DC
18
GND
Ground
19
_VSYNCIN
0/3.3 V DC
20
CLKIN
21
GND
Ground
22
GND
Ground
23
_IDIN
0/3.3 V DC
24
_SET
0/3.3 V DC
25
_SREQ
0/3.3 V DC
26
_READY
0/3.3 V DC
27
RXD
28
GND
Ground
29
_RST
0/3.3 V DC
30
GND
Ground
31
_W_UP
0/3.3 V DC
32
+24VSL
24 V DC
2-3-5
2KJ/2KH
Connector
Pin No.
YC14
+5V
5 V DC
-12V
12 V DC
LCDUD3
LCDUD2
LCDUD1
LCDUD0
LCDCP
0/3.3 V DC
LCDFLM
0/3.3 V DC
GND
Ground
10
LCDENB
0/3.3 V DC
11
GND
Ground
12
LCDLP
0/3.3 V DC
13
LCDV0
0/3.3 V DC
YC15
SCAN7
Connected
to the operation PWB
SCAN6
SCAN5
SCAN4
SCAN3
SCAN2
SCAN1
SCAN0
Connected
to the LCD
PWB
Signal
I/O
Voltage
Description
+5V
5 V DC
10
BUZERDRN
0/3.3 V DC
11
SGND
Ground
YC16
KEY0
Connected
to the operation PWB
KEY1
KEY2
KEY3
KEY4
KEY5
KEY6
KEY7
KEY8
10
KEY9
11
LED4
12
LED3
13
LED2
14
LED1
15
LED0
16
POWERKEY
0/3.3 V DC
YC22
+24V
24 V DC
Connected
to the power
source PWB
GND
Ground
2-3-6
2KJ/2KH
2-3-3
Engine PWB
B1
11
10
6
YC15
YC16
B12
1
2
YC8
A12
YC24
YC4
A1
YC5
2
1
U11
YC12
U7
U8
YC26
YC10
1
2
U6
13
1
A9
B1
YC14
4
U9
14
YC3
YC13
1
YC22
U3
A1
B9 4
U10
YC20
2 YC6 1
1
1
5
YC2
16
15
U1
7
20
19
U2
U12
YC1
U14
U13
YC23 1 YC19
U5
10
21
8
U4
YC17
YC25
2
YC18
YC7
YC9
A8
22 A9
23
1
A2
A1
B2
B1
B8
B9
2-3-7
2KJ/2KH
Connector
Pin No.
YC1
_RST_ENG
SCANHLD
0/3.3 V DC
ENGHLD
0/3.3 V DC
AFEOVSYNC
GND
Ground
MPWB 24V down signal
Connected
to the main
PWB
YC3
Connected
to the polygon motor,
cooling fan
motor 1,
overflow
sensor,
cleaning
lamp and
fuser thermistor
2-3-8
Signal
I/O
I
Voltage
0/3.3 V DC
Description
MPWB reset signal
_24V_DOWN
0/3.3 V DC
PVSYNC
GND
Ground
EGOUTPEN
0/3.3 V DC
10
PLGCLK
11
SLEEP
0/3.3 V DC
12
GND
Analog
Ground
13
EGSIRN
0/3.3 V DC
14
EGSDIR
0/3.3 V DC
15
GND
Ground
16
EGSBSY
0/3.3 V DC
17
EGSDO_BUF
18
GND
19
EGSCLK_BUF
20
EGSDI
A1
PLGCLKN
A2
PLGRDYN
0/3.3 V DC
PM ready signal
A3
PLGDRN
0/3.3 V DC
PM: On/Off
A4
PLGGND
Ground
A5
PLG+24V1
24 V DC
24 V DC power output to PM
A6
FAN1DRN
0/24 V DC
CFM1: On/Off
A7
FAN1+24V1
24 V DC
A8
NC
Not used
A9
NC
Not used
B1
TONEGND
Ground
B2
TONEFULL
0/5 V DC
OFS: On/Off
B3
TONE+5V2
5 V DC
B4
ERASE+24V1
24 V DC
24 V DC power output to CL
B5
NC
Not used
B6
ERASE2N
0/24 V DC
CL: On/Off
B7
ERASE1N
0/24 V DC
CL: On/Off
B8
THERMAGND
Ground
B9
THERMA
Analog
Ground
2KJ/2KH
Connector
Pin No.
Signal
I/O
YC4
RLSOLN
Connected
to the builtin finisher or
job separator
SLSOLN
0/24 V DC
UOPSCLK
0/5 V DC (pulse)
UOPSDI
DC0V/5(?)
Voltage
0/24 V DC
Description
FSSOL: On/Off (return)
UOPSDO
0/5 V DC (pulse)
UOPSRDY
0/5 V DC
UOPSEL
0/5 V DC
SGND
Ground
+5V4
5 V DC
10
PGND
Ground
11
PGND
Ground
12
+24V1
24 V DC
13
+24V1
24 V DC
YC5
A1
ORGTIMN
0/5 V DC
Connected
to the document processor,
original size
detection
sensor,
home position sensor
and original
detection
switch
A2
DOPRDY
0/5 V DC
A3
DOPSEL
0/5 V DC
A4
SGND
Ground
A5
DOPCLK
0/5 V DC (pulse)
A6
DOPSDI
0/5 V DC (pulse)
A7
DOPSDO
0/5 V DC (pulse)
A8
+5V4
5 V DC
A9
PGND
Ground
A10
PGND
Ground
A11
+24V1
24 V DC
A12
NC
Not used
B1
+5V4
5 V DC
B2
ORGLSWN
0/3.3 V DC
OSDS: On/Off
B3
SGND
Ground
B4
+5V4
5 V DC
B5
HPSWN
0/3.3 V DC
HPSW: On/Off
B6
SGND
Ground
B7
+5V4
5 V DC
B8
OPSWN
0/3.3 V DC
ODSW: On/Off
B9
SGND
Ground
B10
NC
Not used
B11
NC
Not used
B12
NC
Not used
2-3-9
2KJ/2KH
Connector
Pin No.
YC6
+24V2
Connected
to the drive
motor and
drum motor
PGND
Ground
MDMREM
0/24 V DC
DM: On/Off
MDMCLK
3.3V
3.3 V DC
MDMRDY
0/3.3 V DC
DM ready signal
3.3V
3.3 V DC
NC
Not used
+24V2
24 V DC
YC7
Connected
to the cassette PWB
2-3-10
Signal
I/O
O
Voltage
-
Description
24 V DC power output to DM
10
PGND
Ground
11
DDMREM
0/24 V DC
DRM: On/Off
12
DDMCLK
13
PGND
Ground
14
DDMRDY
0/3.3 V DC
15
PGND
Ground
16
NC
Not used
TEMP
Analog
HMCLK1
HMCLK2
HUMID
Analog
C1PWSWN
0/3.3 V DC
PWSW: On/Off
C1PDSWN
0/3.3 V DC
PSW: On/Off
+5V2
5 V DC
TONEPY
Analog
SGND
Ground
10
BPWSW
0/3.3 V DC
MPPWSW: On/Off
11
REGSWN
0/3.3 V DC
RSW: On/Off
12
ICLTN
0/24 V DC
DUPFCL: On/Off
13
IPPSWN
0/3.3 V DC
DUPPCSW: On/Off
14
BPPESW
0/3.3 V DC
MPPSW: On/Off
15
SGND
Ground
16
BSOLN
0/24 V DC
MPSOL: On/Off
17
FCLTN
0/24 V DC
PFCL: On/Off
18
REGCLN
0/24 V DC
RCL: On/Off
19
+24V1
24 V DC
20
+24V1
24 V DC
23
+3.3V
3.3 V DC
2KJ/2KH
Connector
Pin No.
YC8
+24V2
+24V2
THVADJC
THVDRN
Connected
to the high
voltage
PWB
Signal
I/O
O
Voltage
Description
24 V DC
24 V DC
Analog
0/3.3 V DC
MHVADJC
Analog
SHVDRN
0/3.3 V DC
MHVDRN
0/3.3 V DC
SHVISELN
0/3.3 V DC
DHVCLKC
10
PGND
Ground
11
PGND
Ground
YC9
A1
LOPSRDY
0/5 V DC
Connected
to the paper
feeder,
paper size
length
switch and
toner container detection switch
A2
LOPSEL2
0/5 V DC
A3
LOPSEL1
0/5 V DC
A4
LOPSEL0
0/5 V DC
A5
LOPSCLK
0/5 V DC (pulse)
A6
LOPSDI
0/5 V DC (pulse)
A7
LOPSDO
0/5 V DC (pulse)
A8
SGND
Ground
A9
+5V2PF
5 V DC
B1
SGND
Ground
B2
+5V2PF
5 V DC
B3
C1PLSW3N
0/3.3 V DC
PLSW: On/Off
B4
C1PLSW2N
0/3.3 V DC
PLSW: On/Off
B5
SGND
Ground
B6
C1PLSW1N
0/3.3 V DC
PLSW: On/Off
B7
TCONDET
0/3.3 V DC
TCDSW: On/Off
B8
SGND
Ground
B9
NC
Not used
YC10
Connected
to the cooling fan
motor 2
YC12
Connected
to the key
counter
YC13
Connected
to the eject
motor
FAN2+24V1
24 V DC
FAN2DRN
0/24 V DC
CFM2: On/Off
+24V1
24 V DC
KEYCN
0/3.3 V DC
SGND
Ground
KEYENBN
0/3.3 V DC
COMDA
COMDB
COMDNA
COMDNB
2-3-11
2KJ/2KH
Connector
Pin No.
YC14
PGND
EXTSWN
0/3.3 V DC
ESW: On/Off
SEPSWN
0/3.3 V DC
FSSW: On/Off
+5V4
5 V DC
YC15
ISMDA
Connected
to the scanner motor
ISMDB
ISMDNA
ISMDNB
YC16
+24V1
24 V DC
+24V1
24 V DC
NC
Not used
LAMPN
0/24 V DC
EL: On/Off
PGND
Ground
PGND
Ground
YC17
+24V
24 V DC
Connected
to the power
source
PWB, left
cover safety
switch and
front cover
safety
switch
+24V
24 V DC
+24V1
24 V DC
PGND
Ground
+24VIL1
24 V DC
+24VIL1
24 V DC
PGND
Ground
+24VIL2
24 V DC
YC18
MHREM
0/3.3 V DC
FH-M: On/Off
Connected
to the power
source PWB
SLEEP
0/3.3 V DC
SHREM
0/3.3 V DC
FH-S: On/Off
SGND
Ground
RELAYREM
0/3.3 V DC
Relay signal
ZCROSS
+24V2
24 V DC
+5V
5 V DC
+5V
5 V DC
+5V
5 V DC
SGND
Ground
+3.3V
3.3 V DC
+3.3V
3.3 V DC
GND
Ground
GND
Ground
GND
Ground
10
+5V3
5 V DC
YC25
PGND
Ground
Connected
to the paper
feeder
+24V1
24 V DC
Connected
to the eject
switch and
feedshift
switch
Connected
to the
inverter
PWB
YC23
Connected
to the main
PWB
2-3-12
Signal
I/O
-
Voltage
-
Description
Ground
2KJ/2KH
2-3-4
Cassette PWB
SW1
YC6
YC1
4
23
YC4 1
YC2
YC8
YC7
1
2
TH2
YC3
TH1
YC5
13
2-3-13
2KJ/2KH
Connector
Pin No.
Signal
I/O
Voltage
Description
YC1
TEMP
Analog
Connected
to the
engine PWB
HMCLK1
HMCLK2
HUMID
Analog
C1PWSWN
0/3.3 V DC
PWSW: On/Off
C1PDSWN
0/3.3 V DC
PSW: On/Off
+5V2
5 V DC
TONEPY
Analog
SGND
Ground
10
BPWSW
0/3.3 V DC
MPPWSW: On/Off
11
REGSWN
0/3.3 V DC
RSW: On/Off
12
ICLTN
Analog
DUPFCL: On/Off
13
IPPSWN
0/3.3 V DC
DUPPCSW: On/Off
14
BPPESW
0/3.3 V DC
MPPSW: On/Off
15
SGND
Ground
16
BSOLN
0/24 V DC
MPSOL: On/Off
17
FCLTN
0/24 V DC
PFCL: On/Off
18
REGCLN
0/24 V DC
RCL: On/Off
19
+24V1
24 V DC
20
+24V1
24 V DC
23
+3.3V
3.3 V DC
YC2
SGND
Ground
Connected
to the paper
switch
C1PDSWN
0/3.3 V DC
PSW: On/Off
+5V2
5 V DC
YC3
+5V2
5 V DC
Connected
to the toner
container
sensor
TONEPY
Analog
SGND
Ground
YC5
+5V2
5 V DC
Connected
to the MP
paper
switch,
duplex
paper conveying
switch,
duplex feed
clutch, registration
switch and
MP paper
size width
switch
BPPESW
0/3.3 V DC
MPPSW: On/Off
SGND
Ground
+5V2
5 V DC
IPPSWN
0/3.3 V DC
DUPPCSW: On/Off
SGND
Ground
+24V1
24 V DC
ICLTN
0/24 V DC
DUPFCL: On/Off
+5V2
5 V DC
10
REGSW
0/3.3 V DC
RSW: On/Off
11
SGND
Ground
2-3-14
12
BPWSW
0/3.3 V DC
MPPWSW: On/Off
13
+3.3V
3.3 V DC
2KJ/2KH
Connector
Pin No.
Signal
I/O
Voltage
Description
YC6
+24V1
24 V DC
Connected
to the registration
clutch
REGCLN
0/24 V DC
RCL: On/Off
YC7
+24V1
24 V DC
Connected
to the paper
feed clutch
FCLTN
0/24 V DC
PFCL: On/Off
YC8
BSOLN
0/24 V DC
MPSOL: On/Off
+24V1
24 V DC
Connected
to the MP
solenoid
2-3-15
2-3-16
DL5 SW5
DL4 SW4
DL3 SW3
SW14
SW8
SW11
SW10
SW17
SW16
SW15
SW13
SW7
SW9
SW12
SW6
SW23
SW22
SW21
SW20
SW19
SW18
SW29
SW28
SW27
SW26
SW25
SW24
YC1
DL14
DL9
DL8
DL7
SW34
SW33
SW32
SW31
SW40
SW39
DL13
SW38
DL12
SW37
DL11
DL19
DL18
DL15
SW35
DL16
DL6
DL10
DL17
SW36
SW30
BZ1
11
SW41
SW46
DL21
DL20
SW42
SW47
DL22
SW43
SW45
SW48
SW49
SW44
SW50
SW56
SW55
SW54
DL35
DL34 SW53
DL33
DL32
DL31
DL30
16
SW60
SW59
SW58
SW57
SW51
DL36
SW64
SW63
SW62
SW61
SW52
YC2
DL37
SW67
DL39
SW66
SW65
SW68
DL38 DL40
2-3-5
DL2 SW2
DL1 SW1
SW69
2KJ/2KH
Operation PWB
2KJ/2KH
Connector
Pin No.
YC1
SCAN7
SCAN6
SCAN5
SCAN4
SCAN3
SCAN2
SCAN1
SCAN0
+5V
5 V DC
Connected
to the main
PWB
YC2
Connected
to the main
PWB
Signal
I/O
Voltage
Description
10
BUZERDRN
0/3.3 V DC
11
SGND
Ground
POWERKEY
Analog
LED0
LED1
LED2
LED3
LED4
KEY9
KEY8
KEY7
10
KEY6
11
KEY5
12
KEY4
13
KEY3
14
KEY2
15
KEY1
16
KEY0
2-3-17
2KJ/2KH
2-3-6
YC5
2
1
1
YC4
1
1
YC2
YC6
YC1
3
1
YC8
2
SW1
A13
YC3
U2
A1
YC9
YC7
1
B1
B13
2-3-18
2KJ/2KH
Connector
Pin No.
Signal
I/O
Voltage
Description
YC1
24V
24 V DC
Connected
to the paper
feeder
PGND
Ground
YC2
+24V1
24 V DC
Connected
to the
engine PWB
PGND
Ground
YC3
A1
5V
Not used
Connected
to the
engine PWB
and paper
feeder
A2
SGND
Not used
A3
5V
5 V DC
A4
SGND
Ground
A5
5V
5 V DC
A6
SGND
Ground
A7
SDI
0/5 V DC (pulse)
A8
SDO
Analog
A9
SCLK
0/5 V DC (pulse)
A10
SEL0
0/5 V DC
A11
SEL1
0/5 V DC
A12
SEL2
0/5 V DC
A13
RDY
0/5 V DC
B1
RDY
0/5 V DC
B2
SEL2
0/5 V DC
B3
SEL1
0/5 V DC
B4
SEL0
0/5 V DC
B5
SCLK
0/5 V DC (pulse)
B6
SDO
0/5 V DC (pulse)
B7
SDI
0/5 V DC (pulse)
B8
SGND
Ground
B9
5V
5 V DC
B10
SGND
Ground
B11
5V
5 V DC
B12
SGND
Not used
B13
5V
Not used
YC4
SGND
Ground
Connected
to the cassette left
cover safety
switch, cassette paper
size width
switch and
cassette
paper size
length
switch
COVOPN
0/24 V DC
CLCSSW: On/Off
SGND
Ground
SIZEA
0/5 V DC
CPWSW: On/Off
SIZEB
0/5 V DC
CPLSW: On/Off
SIZEC
0/5 V DC
CPLSW: On/Off
SGND
Ground
SIZED
0/5 V DC
CPLSW: On/Off
2-3-19
2KJ/2KH
Connector
Pin No.
YC5
SGND
PE
0/5 V DC
CPSW: On/Off
5V
5 V DC
NC
Not used
SGND
Ground
FEED
0/5 V DC
CFSW: On/Off
5V
5 V DC
24V
24 V DC
CLT_RE
0/24 V DC
CPFCL: On/Off
24V
24 V DC
MOTA
MOTB
MOTA-
MOTB-
Connected
to the cassette paper
switch
YC6
Connected
to the cassette feed
switch
YC8
Connected
to the cassette paper
feed clutch
YC9
Connected
to the cassette drive
motor
2-3-20
Signal
I/O
-
Voltage
-
Description
Ground
2KJ/2KH-2
2-4 Appendixes
Part No.
Alternative part
No.
2AR07220
Separation pulley
PULLEY, SEPARATION
2AR07230
Forwarding pulley
2AR07240
2AR07220
PULLEY, SEPARATION
2AR07230
2AR07240
PULLEY BYPASS
302KK08210
2KK08210
MP separation pad
302KK94450
2KK94450
302KK94230
2KK94230
302KK24140
2KK24140
302KK94570
2KK94570
Cam
CAM MPF
302KK08040
2KK08040
Slit glass
2C912280
Contact glass
CONTACT GLASS
2C912250
Mirror 1
MIRROR A
302KK17320
2KK17320
MIRROR B
302KK17330
2KK17330
Lens
LENS
Reflector
REFLECTOR SCANNER
2C912110
302KK94220
2KK94220
2C927090
Exposure lamp
SENSOR ORIGINAL
Optical rail
RAIL SCANNER
LK-460
302KK93060
2KK93060
Transfer roller
ROLLER TRANSFER
302C917011
2C917011
Separation electrode
2C917080
Developing unit
DV-460
302KK93020
2KK93020
Drum unit
MK-460/MAINTENANCE KIT
1702KH0UN0
072KH0UN
Fuser unit
FK-460(A)
302KK93040
2KK93040
FK-460(E)
302KK93050
2KK93050
Heat roller
302KK94240
2KK94240
Press roller
302KK94290
2KK94290
SEPARATOR ASSY
302FT20120
2FT20120
Eject roller
302KK94300
2KK94300
Eject pulley
PULLEY EXIT
302KK28030
2KK28030
Switchback roller
302KK94310
2KK94310
Switchback pulley
Ozone filter
FILTER OZONE A
2C921040
302KK33050
2KK33050
2-4-1
2KJ/2KH-2
Section
Test copy
Perform at the maxiand test print mum copy size
Maintenance
part/location
Section
Paper feed
section
150K
Page
Page
User call
150K
Check
Replace
P.1-5-6
Separation pulley
Check
Replace
P.1-5-3
Forwarding pulley
Check
Replace
P.1-5-6
Check
Replace
P.1-5-13
Cassette separation
pulley
Check
Replace
P.1-5-11
Cassette forwarding
pulley
Check
Replace
P.1-5-13
Check
Replace
Clean
P.1-5-18
MP separation pad
Check
Replace
P.1-5-18
Check
Replace
Clean
P.1-5-21
Check
Clean
Clean
P.1-5-22
Right registration
cleaner
Check
Replace
Clean
Cam
Check
Replace
Grease
2-4-2
User call
2KJ/2KH-2
Maintenance
part/location
Section
Optical
section
User call
150K
Slit glass
Clean
Clean
Contact glass
Clean
Clean
Mirror 1
Clean
Clean
Lens
Clean
Reflector
Clean
Check
Replace
Check
Clean
Optical rail
Check
Grease
Check noise and shifting and then apply optical rail grease PG671 (P/N: 60170001).
Check
Clean
Clean
User call
150K
Transfer roller
Clean
Clean
Separation electrode
Check
Clean
User call
150K
Check
Replace
User call
150K
Check
Replace
Replace
Exposure lamp
Section
Transfer/
separation
section
Section
Developing
section
Section
Maintenance
part/location
Maintenance
part/location
Developing unit
Maintenance
part/location
Page
P.1-5-24
P.1-5-35
Page
P.1-5-45
Page
P.1-5-44
Page
P.1-5-43
2-4-3
2KJ/2KH-2
Section
Fuser
section
Maintenance
part/location
User call
150K
Fuser unit
Check
Replace
Heat roller
Press roller
P.1-5-47
Clean
P.1-5-55
Clean
P.1-5-49
Check
Replace
Clean
P.1-5-54
User call
150K
Check
Clean
Eject pulley
Check
Clean
Switchback roller
Check
Clean
Switchback pulley
Check
Clean
User call
150K
Covers
Clean
Clean
Original cover
Clean
Clean
User call
150K
Ozone filter
Check
Clean
Image quality
Check
Adjust
Check
Adjust
Maintenance
part/location
Section
Covers
Section
Other
2-4-4
Page
Section
Maintenance
part/location
Maintenance
part/location
Page
Page
Page
2KJ/2KH
Item
Image
Description
Maintenance mode
Item No.
Mode
Original
Page
U053
POLY
P.1-3-16
U053
MAIN
P.1-3-16
U034
LSU BYP
P.1-3-13
U034
LSU OUT
P.1-3-13
U034
RCL BYP
P.1-3-12
U034
RCL ON
P.1-3-12
U402
LESD
P.1-3-53
U402
TRAIL
P.1-3-53
U402
AC
P.1-3-53
Data processing
U065
Test chart
P.1-3-18
Remarks
10
2-4-5
2KJ/2KH
Adjusting
order
11
Item
Image
Description
Maintenance mode
Item No.
12
Original
Mode
U065
U070
CONVEY SPEED 1
U067
ADJUST DATA1
U072
1sided
U066
ADJUST DATA1
U071
LEAD 1
U403
B MARGIN
U404
B MARGIN/
U403
D MARGIN
U404
D MARGIN/
U403
A MARGIN
C MARGIN
A MARGIN/
C MARGIN/
Test chart
Page
P.1-3-18
P.1-3-22
Test chart
P.1-3-20
P.1-3-25
Test chart
P.1-3-19
13
14
15
16
U404
When maintenance item U092 (Adjusting the scanner automatically) is run using the specified original (P/N 302FZ56990),
the following adjustments are automatically made:
Adjusting the scanner magnification (U065)
Adjusting the scanner leading edge registration (U066)
Adjusting the scanner center line (U067)
When maintenance item U076 (Adjusting the DP automatically) is run using the specified original (P/N 302AC68243),
the following adjustments are automatically made:
Adjusting the DP magnification (U070)
Adjusting the DP scanning timing (U071)
Adjusting the DP center line (U072)
P.1-3-23
Test chart
P.1-3-54
P.1-3-55
Test chart
P.1-3-54
P.1-3-55
Test chart
P.1-3-54
P.1-3-55
Remarks
U065: For copying an original placed on the contact glass.
U070: For copying originals from the DP.
Duplex copying: select CONVEY SPEED 2
U067: For copying an original placed on the contact glass.
Rotate copying: select ADJUST DATA2
U072: For copying originals from the DP.
Duplex copying (first page): select 2sided front
Duplex copying (second page): select 2sided back
U066: For copying an original placed on the contact glass.
Rotate copying: select ADJUST DATA2
U071: For copying originals from the DP.
Duplex copying: select LEAD 2
U403: For copying an original placed on the contact glass.
U404: For copying originals from the DP.
Image quality
Item
100% magnification
Enlargement/reduction
Lateral squareness
Leading edge registration
Left-right difference
Curling
Specifications
Machine: 0.8%
Using DP: 1.5%
Machine: 1.0%
Using DP: 1.5%
Machine: 1.5 mm/375 mm
Using DP: 3.0 mm/375 mm
Cassette: 2.5 mm
MP tray: 2.5 mm
Duplex mode: 2.5 mm
Cassette: 1.5 mm or less
MP tray: 1.5 mm or less
Duplex mode: 2.0 mm or less
Cassette: 2.0 mm or less
MP tray: 2.0 mm or less
Duplex mode: 3.0 mm or less
Simplex mode: 10.0 mm or less
Duplex mode: 10.0 mm or less
2-4-6
AC IN
MSW
FTS1
FH-M
FTH
PDPWB
FH-S
OPWB
3
2
1
INLET
FTS2
LSU
1
2
3
1/2
3/4
5/6
7/8
9/10
11
SCAN7/SCAN6
SCAN5/SCAN4
SCAN3/SCAN2
SCAN1/SCAN0
+5V/BUZERDRN
SGND
1
2
3
4
5
6
7
8
9
10
11
12
13
16/15
14/13
12/11
10/9
8/7
6/5
4/3
2/1
13
12
11
10
9
8
7
6
5
4
3
2
1
KEY0/KEY1
KEY2/KEY3
KEY4/KEY5
KEY6/KEY7
KEY8/KEY9
LED4/LED3
LED2/LED1
LED0/POWERKEY
Vdd
Vee
UD3
UD2
UD1
UD0
CP
FLM
DISPOFF
LOAD
V0
VSS
F.G
LCDPWB
1
2
3
3
2
1
BAT
CH
1 MH
COM
LIVE
2 SH
1
1
3 LIVE
YC4
5
4
3
2
1
PM
1
2
3
4
5
APCPWB
+5V1
PDN
SGND
YC1
YC6
SCAN7/SCAN6
SCAN5/SCAN4
SCAN3/SCAN2
SCAN1/SCAN0
+5V/BUZERDRN
SGND
KEY0/KEY1
KEY2/KEY3
KEY4/KEY5
KEY6/KEY7
KEY8/KEY9
LED4/LED3
LED2/LED1
LED0/POWERKEY
YC22
2 GND
1 +24V
1/2
3/4
5/6
7/8
9/10
11
YC15
1/2
3/4
5/6
7/8
9/10
11/12
13/14
15/16
YC16
YC14
1 +5V
2 -12V
3 LCDUD3
4 LCDUD2
5 LCDUD1
6 LCDUD0
7 LCDCP
8 LCDFLM
9 GND
10 LCDENB
11 GND
12 LCDLP
13 LCDV0
YC2
13
12
11
10
9
8
7
6
5
4
3
2
1
YC1
YC5
5V1
VDOP
VDON
SAMPLEN
OUTPEN
SGND
PDN
7
6
5
4
3
2
1
1
2
3
4
5
6
7
1
2
3
4
5
6
7
7
6
5
4
3
2
1
1
2
1
2
3
4
5
5
4
3
2
1
GND
+24V
+24V
+24V
GND
GND
1
2
YC3
PSPWB
1
2
3
4
5
6
YC2
1
3/2
5/4
7/6
YC1
1 2
2 1
Fax kit
(Option)
YC1
YC10
MPWB
+24V2
RELAYREM/ZCROSS
SHREM/GND
MHREM/SLEEP
5V1
VDOP
VDON
SAMPLEN
OUTPEN
SGND
PDN
1
2
3
5V/NC
TG/GND
RS/GND
CP/GND
PHY2/GND
GND/Vout1
Vout2/GND
NC/CCDPWR
16/15
14/13
12/11
10/9
8/7
6/5
4/3
2/1
1/2
5V/NC
3/4
TG/GND
5/6
RS/GND
7/8
CP/GND
PHY2/GND 9/10
GND/Vout1 11/12
Vout2/GND 13/14
NC/CCDPWR 15/16
NC
NEUTRAL
NEUTRAL
1
2
3
4
5
1
2
3
4
5
LIVE
LIVE
1/2
3/4
5/6
7/8
9/10
11/12
YC9
CL
PLSW
TCDSW
R3
B2
G1
OFS
1
2
3
4
1
2
3
4
1 1
2 2
FCSSW
1 3
2 2
3 1
1 2
2 1
LCSSW
B3
W2
R1
CFM1
1
2
3
4
5
6
2 2
3 1
PSW
TCS
5V
PE
SGND
1
2
3
1
2
3
4
5
6
7
8
9
10
20/19
18/17
16/15
14/13
12/11
10/9
8/7
6/5
4/3
2/1
YC7
1 3
6
5
4
3
2
1
YC8
+5V
+5V
+5V
GND
+3.3V
+3.3V
GND
GND
GND
+5V
EGSDI/EGSCLK_BUF
GND/EGSDO_BUF
EGSBSY/GND
EGSDIR/EGSIRN
GND/SLEEP
PLGCLK/EGOUTPEN
GND/PVSYNC
_24V_DOWN/GND
AFEOVSYNC/ENGHLD
SCANHLD/_RST_ENG
KMDET/NC
KMDREQ/KMACK
KMRXD/SGND
KMTXD/SGND
SGND/SGND
+5V/+5V
GND/5V
CLKOUT/5V
GND/MREOUT
_HSYNCOUT/GND
_VSYNCOUT/_IDOUT
GND/GND
TXD/_STS
_MAIN_STS/FAXDOWN
MREIN/GND
_VSYNCIN/CLKIN
GND/GND
_IDIN/_SET
_SREQ/_READY
RXD/GND
_RST/GND
_W_UP/+24VSL
1/2
3/4
5/6
7/8
9/10
11/12
13/14
15/16
17/18
19/20
21/22
23/24
25/26
27/28
29/30
31/32
1/2
3/4
5/6
7/8
9/10
11/12
13/14
15/16
17/18
19/20
21/22
23/24
25/26
27/28
29/30
31/32
32/31
30/29
28/27
26/25
24/23
22/21
20/19
18/17
16/15
14/13
12/11
10/9
8/7
6/5
4/3
2/1
32/31
30/29
28/27
26/25
24/23
22/21
20/19
18/17
16/15
14/13
12/11
10/9
8/7
6/5
4/3
2/1
GND/5V
CLKOUT/5V
GND/MREOUT
_HSYNCOUT/GND
_VSYNCOUT/_IDOUT
GND/GND
TXD/_STS
_MAIN_STS/FAXDOWN
MREIN/GND
_VSYNCIN/CLKIN
GND/GND
_IDIN/_SET
_SREQ/_READY
RXD/GND
_RST/GND
_W_UP/+24VSL
16
15
13
12
1
2
3
4
5
6
7
8
9
10
11
YC3
7/6
5/4
3/2
1
YC2
+24V
+24V
+24V1
PGND
+24VIL1
+24VIL1
PGND
+24VIL2
1
2
3
B3
W2
R1
1
2
3
4
3 SGND
2 TONEPY
1 +5V2
YC3
3 +5V2
2 C1PDSWN
1 SGND
YC2
YC4
1 SGND
2 RFSDAT
3 RFSCLK
4 +3.3V
YC1
YC7
+5V2PF
SGND
LOPSDO
LOPSDI
LOPSCLK
LOPSEL0
LOPSEL1
LOPSEL2
LOPSRDY
A9
A8
A7
A6
A5
A4
A3
A2
A1
9
8
7
6
5
4
3
2
1
YC25
2 2 PGND
1 1 +24V1
NC
SGND
TCONDET
C1PLSW1N
SGND
C1PLSW2N
C1PLSW3N
+5V2PF
SGND
B9
B8
B7
B6
B5
B4
B3
B2
B1
9
8
7
6
5
4
3
2
1
YC9
+24V2
RELAYREM/ZCROSS
SHREM/SGND
MHREM/SLEEP
YC18
7
5/6
3/4
1/2
1
2
3
4
5
6
7
8
YC17
YC15
PLGCLKN
PLGRDYN
PLGDRN
PLGGND
PLG+24V1
FAN1DRN
FAN1+24V1
NC/NC
TONEGND
TONEFULL
TONE+5V2
ERASE+24V1
NC
ERASE2N
ERASE1N
THERMAGND
THERMA
SGND/ERSTN
SCK/WRSI
WRSO/VPP
+3.3V
ACSUTN
+24V
SGND
TCROTDET
+5V2
YC19
1
2
3
4
5
B_
A_
B
A
EGSDO_BUF/EGSCLK_BUF
SGND/EGSDI
EGSBSY/SGND
EGSDIR/EGSIRN
SGND/SLEEP
PLGCLK/EGOUTPEN
SGND/PVSYNC
24VDOWN/SGND
AFEOVSYNC/ENGHLD
SCANHLD/_RST_ENG
+3.3V
IUID2SCL
IUIDSDA
SGND
IUID2DETN
+3.3V
IUID1SCL
IUIDSDA
SGND
IUID1DETN
FUMLTN
SGND
+24V1
DHEATN
YC22
A1
A2
A3
A4
A5
A6
A7
A8/A9
B1
B2
B3
B4
B5
B6
B7
B8
B9
3
2
1
9
8
7
6
5
4
3
2
1
9
8
7
6
5
4
3
2/1
1
2
3
4
5
YC1
20/19
18/17
16/15
14/13
12/11
10/9
8/7
6/5
4/3
2/1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
SM
+5V
+5V
+5V
SGND
+3.3V
+3.3V
SGND
SGND
SGND
+5V3
YC23
1
2
3
4
5
6
7
8
9
10
1
2
3
PGND
+24V1
+5V2PF
SGND
5V2PF
SGND
LOPSDO
LOPSDI
LOPSCLK
LOPSEL0
LOPSEL1
LOPSEL2
LOPSRDY
4
3
2
1
1
2
3
4
4
3
2
1
1
2
3
4
ISMDA
ISMDB
ISMDNA
ISMDNB
EPWB
CPWB
YC16
A8
A9
A10
A11
6
5
4
+5V4 B7
OPSWN B8
SGND B9
1
2
3
4
5
13
12
11
10
9
8
7
6
5
4
3
2
1
4
3
2
1
1
2
3
4
YC8
COUT1
COUT2
CIN1
CIN2
NC
YC20
+24V1
KEYCN
SGND
KEYENBN
1
2
3
4
5
1
2
3
4
YC10
10
9
8
7
6
4
5
6
7
8
YC7
+24V1 1
FCLTN 2
YC6
+24V1 1
REGCLN 2
YC8
BSOLN 1
+24V1 2
YC5
BPWSW 12
+3.3V 13
+5V2 9
REGSW 10
SGND 11
1 1
2 2
3 3
1 2
2 1
1
2
3
1
2
2
1
MPSOL
RCL
1
2
2
1
1 2
2 1
Duplex
unit
(Option)
Zener PWB
+5V
GND
FG
+24V
Document
processor
(Option)
ORGVSYNC
DPRDY
DPSEL
GND
SCLK
SDO
SDI
MPPWSW
DUPFCL
DUPPCSW
MPPSW
1
2
2
1
HVTPWB
CFM2
2
3
1
4
YC1
YC2
6
5
4
7
3
2
1
8
9
10
DRM
DM
GND/GND
SHVISELN/HVCLKC
SHVDRN/MHVDRN
THVDRN/MHVADJC
+24V2/THVADJC
+24V2
RSW
1
2
3
+24V
GND
SS
CLK
GAIN
LD
CW
+24V
GND
SS
CLK
GAIN
LD
CW
-A
A
B
-B
EM
ESW
FSSW
ODSW
HPSW
Key Counter
(Option)
1
2
3
4
5
6
7
1
2
3
4
5
6
7
4
3
2
1
PFCL
1 2
2 1
1 1
2 2
3 3
1
2
3
4
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
EL
OSDS
3
2
4
1
6
5
4
7
3
2
1
8
9
10
11
12
13
14
15
16
Built-in
finisher
or Job
separator
(Option)
+5V
OUT1
OUT2
GND
1
2
3
1
2
3
1
2
3
3
2
4
1
6
5
4
7
3
2
1
8
9
10
11
12
13
14
15
16
1
2
5
4
3
2
1
1
2
3
4
1
2
3
1
2
3
1
2
3
6
5
4
7
3
2
1
8
9
10
11
12
13
14
15
16
10/11
8/9
6/7
4/5
2/3
1
1
2
3
4
2
1
1
2
3
4
5
1 3
2 2
3 1
1
2
LAMP
N.C.
N.C.
LAMP
1
2
2
1
5
4
3
13
12
11
FAN2+24V1
FAN2DRN
2
1
9 9
10 10
11 11
12 12
13 13
14 14
15 15
16 16
+24V2
PGND
DDMREM
DDMCLK
PGND
DDMRDY
PGND
NC
YC12
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
4
3
2
1
4
3
2
1
+24V2
PGND
MDMREM
MDMCLK
3.3V
MDMRDY
3.3V
NC
YC6
COMDA
COMDB
COMDNA
COMDNB
YC13
YC24
+24V1 1
TCONTN 2
+5V
DBTXD
DBRXD
NC
SGND
YC26
+24V1
+24V1
PGND
PGND
+5V4
SGND
UOPSEL
UOPSRDY
UOPSDO
UOPSDI
UOPSCLK
SLSOLN
RLSOLN
YC4
+5V4
SEPSWN
EXTSWN
PGND
YC14
NC B10 3
NC B11 2
NC B12 1
9
8
7
12
11
10
5
4
3
2
+5V4 B4
HPSWN B5
SGND B6
+5V4 B1
ORGLSWN B2
SGND B3
+5V4
PGND
PGND
+24V1
+5V2 1
BPPESW 2
SGND 3
+5V2
IPPSWN
SGND
+24V1
ICLTN
12
11
10
9
8
7
6
+24V1 A12 1
A1
A2
A3
A4
A5
A6
A7
YC5
ORGTIMN
DOPRDY
DOPSEL
SGND
DOPCLK
DOPSDI
DOPSDO
INPWB
PGND/PGND 10/11
SHVISELN/DHVCLKC 8/9
SHVDRN/MHVDRN 6/7
THVDRN/MHVADJC 4/5
+24V2/THVADJC 2/3
+24V2
1
6/5 24V/24V
4/3 NC/LAMP
2/1 GND/GND
1/2
3/4
5/6
+24V1/+24V1
NC/LAMPN
PGND/PGND
+3.3V
RFSDAT/RFSCLK
+24V1/+24V1
FCLTN/REGCLN
SGND/BSOLN
IPPSWN/BPPESW
REGSWN/ICLTN
SGND/BPWSW
+5V2/TONEPY
C1PWSWN/C1PDSWN
HMCLK2/HUMID
TEMP/HMCLK1
23
21/22
19/20
17/18
15/16
13/14
11/12
9/10
7/8
5/6
3/4
1/2
23
21/22
19/20
17/18
15/16
13/14
11/12
9/10
7/8
5/6
3/4
1/2
+3.3V
RFSDAT/RFSCLK
+24V1/+24V1
FCLTN/REGCLN
SGND/BSOLN
IPPSWN/BPPESW
REGSWN/ICLTN
SGND/BPWSW
+5V2/TONEPY
C1PWSWN/C1PDSWN
HMCLK2/HUMID
TEMP/HMCLK1
CCDPWB
2KJ/2KH
Wiring diagram
2-4-7
2KJ/2KH
16
15
13
12
1
2
3
4
5
6
7
8
9
10
11
PGND
+24V1
+5V2PF
SGND
5V2PF
SGND
LOPSDO
LOPSDI
LOPSCLK
LOPSEL0
LOPSEL1
LOPSEL2
LOPSRDY
PAPER FEEDER
YC2
1
2
4
3
2
1
CHPWB
1
2
3
4
1
2
3
4
1
2
3
4
YC2
1
2
3
4
YC3
24V
PGND
CH
1
2
3
4
5
6
7
8
9
10
11
12
13
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
5V
SGND
5V
SGND
5V
SGND
SDI
SDO
SCLK
SEL0
SEL1
SEL2
RDY
1
2
3
4
5
6
7
8
9
10
11
12
13
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
RDY
SEL2
SEL1
SEL0
SCLK
SDO
SDI
SGND
5V
SGND
5V
SGND
5V
YC1
SGND
COVOPN
SGND
SIZEA
SIZEB
SIZEC
SGND
SIZED
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
2 2 SGND
1 1 SIZE_A
CPWSW
4
3
2
1
4
3
2
1
SIZE_B
SIZE_C
SGND
SIZE_D
CPLSW
YC5
SGND
PE
5V
NC
1
2
3
4
1
2
3
4
3 3 SGND
2 2 PE
1 1 5V
CPSW
1
2
3
3 3 SGND
2 2 FEED
1 1 5V
CFSW
CMPWB
YC6
SGND
FEED
5V
1
2
3
YC8
1 1
2 2
24V
CLT_RE
CPFCL
YC9
24V
MOTA
MOTB
MOTAMOTB-
1
2
3
4
5
1
2
3
4
5
CDM
24V
PGND
PGND
+24V1
+5V2PF
SGND
5V2PF
SGND
LOPSDO
LOPSDI
LOPSCLK
LOPSEL0
LOPSEL1
LOPSEL2
LOPSRDY
16
15
13
12
1
2
3
4
5
6
7
8
9
10
11
1 1
2 2
CLCSSW
YC4
YC3
4
3
2
1
YC1
1
2
2 2 SGND
1 1 OPEN
2-4-8
INSTALLATION GUIDE
C
D
English
Supplied parts
A
B
C
D
E
Franais
Pices fournies
A
B
C
D
E
Espaol
Piezas suministradas
A
B
C
D
E
Deutsch
Gelieferte Teile
A
B
C
D
E
Italiano
Parti di fornitura
A
B
C
D
E
A
B
C
D
E
(DP) ......................... 1
.............................. 1
.............................. 1
................................ 2
M4 14 ........................ 5
A
B
C
D
E
DP....................1
..........................1
..............................1
................................2
M4 14 ........................5
F Film .......................................................... 1
G Label A (for 120 V specifications
for 220 V - 240 V specifications )................. 1
H Label B (for 220 V - 240 V specifications)... 1
Procedure
Before installing the document processor, be
sure to turn the main power switch of the
machine off and unplug the power cable from
the wall outlet.
Procdure
Avant dinstaller le chargeur de document,
veillez mettre la machine hors tension et
dbrancher le cble dalimentation de la prise
murale.
Procedimiento
Antes de instalar el procesador de documentos,
asegrese de desconectar el interruptor
principal de la mquina y desenchufar el cable
elctrico del tomacorriente de la pared.
Verfahren
Schalten Sie unbedingt den Betriebsschalter der
Maschine aus, und trennen Sie das Netzkabel
von der Netzsteckdose, bevor Sie den
Vorlageneinzug installieren.
Procedura
Prima di installare lalimentatore di originali,
assicurarsi di spegnere linterruttore principale
di alimentazione della macchina e scollegare la
spina del cavo di alimentazione dalla presa a
muro della rete elettrica.
DP
F ............................1
G A120V 220V-240V ..1
H B220V-240V ............1
DP
OFF
Installing the DP
Installation du DP
Instalacin del DP
Installieren des DP
Installazione del DP
DP
2. 2 (D)
1. 2 1
DP
1. (1)2
2. (D)2
3. Insert the pins (D) into the hinge holes (2) of DP (A) and slide the DP
(A) toward the front side to install it.
3. Insrez les goupilles (D) dans les orifices de charnire (2) du DP (A),
puis faites glisser le DP (A) vers lavant pour linstaller.
3. Inserte los pasadores (D) en los orificios de bisagra (2) del DP (A) y
deslice el DP (A) hacia el lado frontal para instalar.
3. Inserire i perni (D) nei fori della cerniera (2) del DP (A) e fare scorrere il
DP (A) verso il lato anteriore per installarlo.
4. 4 M4 14(E) DP(A)
1
3
4. M4 14(E)4 DP(A)
1
3
0 mm
1 mm
0 mm
1 mm
F
F
3
3
Adhsion du film
5. Nettoyez le verre fendu (3) l'aide d'un chiffon sec.
6. Alignez le bord du film (F) avec le bord (4) du verre fendu (3) et insrez
le tout en place dans les limites de la plage des valeurs de rfrence.
Fijacin de la pelcula
5. Limpie el cristal de paso (3) con un pao seco.
6. Alinee el borde de la pelcula (F) con el borde (4) del cristal de paso (3)
y pguela, en su lugar, dentro del rango del valor de referencia.
5. 3
6. F34
7. (B)
(B) 90
8. DP(A) (B) DP
5. (3)
6. (F) (3) (4)
7. (B)
(B) 90 (5)
8. DP (A) (B) DP
G/H
G/H
1 mm 0 mm
1 mm 0 mm
Pegado de etiquetas
10. Despus de limpiar con alcohol, pegue la etiqueta de precaucin [No
deje documentos en el equipo.] (F), etiqueta de precaucin [Cara
Arriba] (G) y la etiqueta [Procedimiento de funcionamiento] (H) del
correspondiente idioma.
9. (6)
10. (G)(H)
9. (6)
20mm
20mm
20mm
b
b
20mm
a
Checking the operation
1. To check the machine operation, prepare an A3 size original (a) where four lines (b) are drawn 20 mm from the edges and one line (c) is drawn at the
center.
2. Connect the power plug to the wall outlet and turn the main power switch on. Load A3 paper into the 1st level cassette.
3. Set the original (a) on the DP original table and run a proof copy. Check the operation and the copy example.
4. If the gap between the original (a) and the copy example exceeds the reference value, perform adjustments. For the procedure, see the following
pages.
Before checking image from the DP, check and adjust image from the machine. For details, see the service manual of the machine.
Vrification du fonctionnement
1. Pour vrifier le fonctionnement de la machine, prparez un original de format A3 (a) sur lequel quatre lignes (b) ont t traces 20 mm des bords,
et sur lequel une ligne (c) a t trace au centre.
2. Insrer la fiche dalimentation de la machine dans la prise murale et mettre la machine sous tension.
3. Placez loriginal (a) dans le DP et effectuez une copie de test pour vrifier le fonctionnement et lexemple de copie.
4. Si lcart entre loriginal (a) et lexemple de copie est suprieur la valeur de rfrence, effectuez les rglages ncessaires. Pour la marche suivre,
reportez-vous aux pages suivantes.
Avant de vrifier limage sur le DP, vrifier et rgler limage sur la machine. Pour plus de dtails, se reporter au manuel de service de la
machine.
4. (a) ( )
DP
4. (a)
DP
<<Checking
image from the DP>>
>>
<<
Be sure to adjust in the following order. If not, the adjustment cannot be performed correctly.
For checking the angle of leading edge, see page 8.
<Reference value> Simplex copying: within 3.0 mm; Duplex copying: within 4.0 mm
For checking the angle of trailing edge, see page 11.
<Reference value> Simplex copying: within 3.0 mm; Duplex copying: within 4.0 mm
For checking the magnification, see page 15.
<Reference value> Within 1.5%
For checking the leading edge timing, see page 17.
<Reference value> Simplex copying: within 2.0 mm; Duplex copying: within 2.0 mm
For checking the center line, see page 19.
<Reference value> Simplex copying: within 2.0 mm; Duplex copying: within 3.0 mm
When using the original for adjustment, automatic adjustment of magnification, leading edge timing and center line can be performed at a time.
For the automatic adjustment using the original for adjustment, see page 21.
<<Vrification
<<
de limage sur le DP>>
>>
Veillez effectuer le rglage en procdant dans lordre suivant. Sinon, il sera impossible dobtenir un rglage correct.
Pour vrifier langle du bord avant, reportez-vous la page 8.
<Valeur de rfrence>Copie recto seul: 3,0 mm max.; copie recto verso: 4,0 mm max.
Pour vrifier langle du bord arrire, reportez-vous la page 11.
<Valeur de rfrence>Copie recto seul: 3,0 mm max.; copie recto verso: 4,0 mm max.
Pour vrifier lagrandissement, reportez-vous la page 15.
<Valeur de rfrence>1,5% max.
Pour vrifier la synchronisation du bord avant, reportez-vous la page 17.
<Valeur de rfrence>Copie recto seul: 2,0 mm max.; copie recto verso: 2,0 mm max.
Pour vrifier la ligne mdiane, reportez-vous la page 19.
<Valeur de rfrence>Copie recto seul: 2,0 mm max.; copie recto verso: 3,0 mm max.
Lorsque vous utilisez loriginal pour effectuer le rglage, vous pouvez effectuer automatiquement le rglage de lagrandissement, de la synchronisation du bord avant et de
la ligne mdiane en une seule fois. Pour le rglage automatique en utilisant loriginal pour effectuer le rglage, reportez-vous la page 21.
<<Verificacin
de la imagen del DP>>
>>
<<
Asegrese de ajustar en el siguiente orden. De lo contrario, el ajuste no puede hacerse correctamente.
Para verificar el ngulo del borde superior, vea la pgina 8.
<Valor de referencia> Copia simple: dentro de 3,0 mm; Copia duplex: dentro de 4,0 mm
Para verificar el ngulo del borde inferior, vea la pgina 11.
<Valor de referencia> Copia simple: dentro de 3,0 mm; Copia duplex: dentro de 4,0 mm
Para verificar el cambio de tamao, vea la pgina 15.
<Valor de referencia> Dentro de 1,5 %
Para verificar la sincronizacin del borde inferior, vea la pgina 17.
<Valor de referencia> Copia simple: dentro de 2,0 mm; Copia duplex: dentro de 2,0 mm
Para verificar la lnea central, vea la pgina 19.
<Valor de referencia> Copia simple: dentro de 2,0 mm; Copia duplex: dentro de 3,0 mm
Cuando utilice el original para el ajuste, puede hacerse un ajuste automtico del cambio de tamao, sincronizacin del borde superior y lnea central al mismo tiempo.
Para el ajuste automtico utilizando el original para el ajuste, vea la pgina 21.
<<berprfen
des Bilds vom DP>>
>>
<<
Die Einstellung in der folgenden Reihenfolge durchfhren. Anderenfalls kann die Einstellung nicht korrekt durchgefhrt werden.
Angaben zur Prfung des Winkels der Vorderkante auf Seite 8. <Bezugswert> Simplexkopie: innerhalb 3,0 mm; Duplexkopie: innerhalb 4,0 mm
Angaben zur Prfung des Winkels der Hinterkante auf Seite 11. <Bezugswert> Simplexkopie: innerhalb 3,0 mm; Duplexkopie: innerhalb 4,0 mm
Angaben zur Prfung der Vergrerung auf Seite 15.
<Bezugswert> Innerhalb 1,5 %
Angaben zur Prfung des Vorderkanten-Timings auf Seite 17. <Bezugswert> Simplexkopie: innerhalb 2,0 mm; Duplexkopie: innerhalb 2,0 mm
Angaben zur Prfung der Mittellinie auf Seite 19.
<Bezugswert> Simplexkopie: innerhalb 2,0 mm; Duplexkopie: innerhalb 3,0 mm
Bei Verwendung des Originals fr die Einstellung knnen die automatischen Einstellungen fr Vergrerung, Vorderkanten-Timing und Mittellinie
gleichzeitig durchgefhrt werden. Angaben zur automatischen Einstellung mithilfe des Originals auf Seite 21.
<<Controllo
di immagine dal DP>>
>>
<<
Verificare che la regolazione avvenga nel seguente ordine. Altrimenti, la regolazione non potr essere seguita correttamente.
Per controllare langolo del bordo principale, vedere pagina 8.
<Valore di riferimento>
Copia simplex:entro 3,0 mm; Copia duplex: entro 4,0 mm
Per controllare langolo del bordo di uscita, vedere pagina 11.
<Valore di riferimento>
Copia simplex:entro 3,0 mm; Copia duplex: entro 4,0 mm
Per controllare lingrandimento, vedere pagina 15.
<Valore di riferimento>
Entro 1,5%
Per controllare la sincronizzazione del bordo principale, vedere pagina 17.
<Valore di riferimento>
Copia simplex:entro 2,0 mm; Copia duplex: entro 2,0 mm
Per controllare la linea centrale, vedere pagina 19.
<Valore di riferimento>
Copia simplex:entro 2,0 mm; Copia duplex: entro 3,0 mm
Quando si utilizza loriginale per la regolazione, la regolazione automatica dellingrandimento, della sincronizzazione del bordo principale e della linea centrale possono
essere eseguiti contemporaneamente. Per la regolazione automatica eseguita con loriginale, vedere pagina 21.
<< >>
8
< > 3.0mm 4.0mm
11
< > 3.0mm 4.0mm
15
< > 1.5
17
< > 2.0mm 2.0mm
19
< > 2.0mm 3.0mm
21
<<
>>
8
3.0mm 4.0mm
11 3.0mm 4.0mm
15 1.5%
17 2.0mm 2.0mm
19 2.0mm 3.0mm
21
3mm/4mm
3mm/4mm
2
3.0mm
4.0mm
3mm/4mm
3mm/4mm
2
Adjusting the DP
1. Open the DP and loosen two adjusting screws (3) of right hinge.
2. Adjust the position of the DP.
For copy example (d): Move the DP down ( ).
For copy example (e): Move the DP up ( ).
Amount of change per scale: Approx. 0.5 mm
Rglage du DP
1. Ouvrez le DP et desserrez les deux vis de rglage (3) de la charnire droite.
2. Rglez la position du DP.
Pour lexemple de copie (d): Dplacez le DP vers le bas ( ).
Pour lexemple de copie (e): Dplacez le DP vers le haut ( ).
Quantit de changement par pas: Environ 0,5 mm
Ajuste del DP
1. Abra el DP y afloje los dos tornillos de ajuste (3) de la bisagra derecha.
2. Ajuste la posicin del DP.
Para la copia de muestra (d): Mueva el DP abajo ( ).
Para la copia de muestra (e): Mueva el DP arriba ( ).
Cantidad de cambio de escala: Aprox. 0,5 mm
Einstellen des DP
1. Den DP ffnen, und die zwei Einstellschrauben (3) des rechten Scharniers lsen.
2. Die Position des DP einstellen.
Fr Kopienmuster (d): Den DP absenken ( ).
Fr Kopienmuster (e): Den DP anheben ( ).
nderungsbetrag pro Skalenstrich: Ca. 0,5 mm
Regolazione del DP
1. Aprire il DP e allentare le due viti di regolazione (3) della cerniera destra.
2. Regolare la posizione del DP.
Per un esempio di copia (d): Muovere il DP verso il basso ( ).
Per un esempio di copia (e): Muovere il DP verso lalto ( ).
Variazione graduale: Circa 0,5 mm
DP
1. DP 2 (3)
2. DP
(d) DP ( )
(e) DP ( )
1 0.5mm
DP
1. DP (3)2
2. DP
(d) DP
(e) DP
1 0.5mm
3. 2 (3)
4. 4 7 8
DP (A) B
B
3. (3)2
4. 4 78
B DP A
B
3mm/4mm
3mm/4mm
2
5.
6. 1 5 (2)
< >
3.0mm
4.0mm
5.
6. (2) 1 5
3.0mm
4.0mm
10
3mm/4mm
3mm/4mm
3.0mm
4.0mm
11
Adjusting the DP
1. Open the DP and release two latches (4) using a flat-head screwdriver.
Rglage du DP
1. Ouvrez le DP et librez les deux verrous (4) laide dun tournevis
tte plate.
Ajuste del DP
1. Abra el DP y suelte los dos pestillos (4) utilizando un destornillador de
punta plana.
Einstellen des DP
1. Den DP ffnen, und die zwei Rasten (4) mit einem
Flachschraubenzieher lsen.
Regolazione del DP
1. Aprire il DP e rilasciare i due fermi (4) utilizzando un giravite a punta
piatta.
DP
2. Die drei Rasten (5) auf der Rckseite des DP mit einem
Flachschraubenzieher lsen, um die Abdeckung (6) zu entfernen.
2. Rilasciare i tre fermi (5) sul retro del DP utilizzando un giravite a punta
piatta per rimuovere il coperchio (6).
2. DP 3 (5) (6)
1. DP 2 (4)
DP
1. DP (4)2
12
2. DP (5)3
(6)
7
2
3mm/4mm
3mm/4mm
10
3. DP
(7)
(f) (8)( )
(g) (8)( )
1 1mm(9)/ 0.5mm(10)
(7)
4. 2 (6)
5. 4 7 8
DP (A) B
B
3. DP
(7)
(f) (8)
(g) (8)
1 1mm(9)/ 0.5mm(10)
(7)
4. 2 (6)
5. 4 78
B DP A
B
13
3mm/4mm
3mm/4mm
6.
7. 1 6 (2)
< >
3.0mm
4.0mm
6.
7. (2) 1 6
3.0mm
4.0mm
14
X'
X
X'
a
-1.5%
Vrification de lagrandissement
Vrifiez lcart entre la ligne (1) de loriginal (a)
et la ligne (2) de lexemple de copie. Si lcart
est suprieur la valeur de rfrence, effectuez
le rglage suivant.
<Valeur de rfrence> 1,5% max.
Controllo dellingrandimento
Controllare la differenza tra la linea (1)
delloriginale (a) e la linea (2) della copia di
esempio. Se la differenza supera il valore di
riferimento, effettuare la seguente regolazione.
<Valore di riferimento> Entro 1,5 %
i
X'
100
+1.5%
.
1. Den Modus auf Wartungsmodus U070 setzen, mit der Belichtungstaste "exp. 1" whlen und
dann die obere und untere Grenze durch Vergrern des Bilds einstellen. Die
Unterbrechungstaste drcken und das Bild an der Probekopie berprfen.
Fr Kopienmuster (h): Den Einstellwert erhhen.
Fr Kopienmuster (i): Den Einstellwert erniedrigen.
nderungsbetrag pro Stufe: 0,2 mm
1. U070 exp.1
(h)
(i)
1 0.2mm
DP
seg
1.5%
1. U070 exp.1
(h)
(i)
1 0.2mm
15
X'
X
X'
a
-1.5%
i
X'
LCD
1. U070 CONVEY SPEED1
(h)
(i)
1 0.2mm
LCD
LCD
1. U070
CONVEY SPEED1
(h)
(i)
1 0.2mm
16
100
+1.5%
2.
3. 1 2 (2)
< > 1.5
2.
3. (2) 1 2
1.5%
2mm
2mm
2
1
2
Vrification de la synchronisation du
bord avant
Vrifiez lcart entre la ligne (1) de loriginal (a)
et la ligne (2) de lexemple de copie. Si lcart
est suprieur la valeur de rfrence, effectuez
le rglage suivant.
<Valeur de rfrence>
Copie recto seul: 2,0 mm max.
Copie recto verso: 2,0 mm max.
< >
2.0mm
2.0mm
1. U071 exp.1
(i)
(k)
1 0.2mm
DP
seg
2.0mm
2.0mm
1. U071 exp.1
(j)
(k)
1 0.2mm
17
2mm
2mm
2
1
2
LCD
1. U071 LEAD1
(j)
(k)
1 0.2mm
LCD
LCD
1. U071
LEAD1
(j)
(k)
1 0.2mm
18
2.
3. 1 2 (2)
< >
2.0mm
2.0mm
2.
3. (2) 1 2
2.0mm
2.0mm
2mm/3mm
2mm/3mm
a
Checking the center line
Check the gap between line (1) of original (a)
and line (2) of copy example. If the gap exceeds
the reference value, perform the following
adjustment.
<Reference value>
For simplex copying: Within 2.0 mm
For duplex copying: Within 3.0 mm
< >
2.0mm
3.0mm
1. U072 exp.1
(l)
(m)
1 0.15mm
DP
seg
(a) (1)
(2)
2.0mm
3.0mm
1. U072 exp1
(l)
(m)
1 0.15mm
19
2mm/3mm
LCD
1. U072 1saided
(l)
(m)
1 0.15mm
LCD
LCD
1. U072 1sided
(l)
(m)
1 0.15mm
20
2mm/3mm
m
2. Make a proof copy again.
3. Repeat steps 1 to 2 until line (2) of copy example shows the
following the reference values.
<Reference value>
For simplex copying: Within 2.0 mm
For duplex copying: Within 3.0 mm
2.
3. 1 2 (2)
< >
2.0mm
3.0mm
2.
3. (2)
1 2
2.0mm
3.0mm
5mm
149 1mm
(149 5mm)
74 1mm
( 8 11 )
1. U076 F R DP
2.
3. 1Gd 20 30 40
LCD CONVEY SPEEDLEAD EDGE ADJ DP CENTER
4. nG1nG2nG3 1 LCD DATANG1NG2
( )
11
1. U076 FR DP
2.
3. OK seg
1Gd 20 30 4:0
LCD CONVEY SPEED,LEAD EDGE ADJ,DP CENTER
4. NG seg (nG1nG2nG3 1 LCD DATANG1NG2
21
11
E
13
11
12
DP
60 DP
1. (C) 1
M4 14(E)
DP
DP
60
60
1. (C) M4 14(E)1
22
13
12
30 DP
1. 2 (11) (12)
2. (12) (13) 2 (11)
DP
30
30
1. (11)2 (12)
2. (12) (13)
(11)2
3. (C) 1
M4 14(E)
3. (C) M4 14(E)1
F
F
B
English
After installing the PF-420, fasten the connector cover (F) in place using an M3 x 8 screw (B).
Note
This step is not required for 22 ppm MFP models (printer-based models) since the connector cover
(F) is already attached.
Franais
Aprs avoir install le PF-420, fixer le couvercle du connecteur (F) en position l'aide d'une vis
M3 x 8 (B).
Pices supplmentaires
B Vis M3 x 8 ................................................ 1
F Couvercle du connecteur......................... 1
Remarque
Cette opration n'est pas ncessaire pour les modles de MFP 22 ppm (modles base
imprimante) car le couvercle du connecteur (F) est dj fix.
Espaol
Despus de instalar el PF-420, apriete la cubierta del conector (F) en su lugar por medio de un
tornillo M3 x 8 (B).
Piezas adicionales
B Tornillo M3 x 8 ......................................... 1
F Cubierta del conector .............................. 1
Nota
Este paso no es necesario para los modelos MFP de 22 ppm (modelos basados en impresoras),
ya que la cubierta del conector (F) ya est instalada.
Deutsch
Nach Installieren deds PF-420 die Steckverbinderabdeckung (F) mittels einer M3 x 8 Schraube (B)
befestigen.
Zustzliche Teile
B M3 8 Schraube ..................................... 1
F Steckverbinderabdeckung ....................... 1
Hinweis
Dieser Schritt ist nicht erforderlich fr MFP-Modell 22 ppm (Modell auf Druckerbasis), da die
Steckverbinderabdeckung (F) dort schon angebracht ist.
Italiano
Dopo l'installazione di PF-420, fissare il coperchio del connettore (F) in posizione utilizzando una
vite M3 x 8 (B).
Parti aggiuntive
B Vite M3 x 8............................................... 1
F Coperchio del connettore ........................ 1
Nota
Questo passo non richiesto per i modelli MPF da 22 ppm (modelli stampante base) poich il
coperchio del connettore (F) gi fissato.
PF-420
PF-420 1 M3 x 8 BF
B M3 x 8 ......................... 1
F .......................... 1
22ppm F
PF-420
B M3 8 .........................1
F ......................1
MFP
22 (F)
2009.4
303MH56811
D
E
English
Supplied parts
A
B
C
D
E
Pices fournies
Partes suministradas
Gelieferte Teile
Parti di fornitura
Verfahren
Procedura
MFP
................................ 1
M3 8 ........................ 4
M3 12 ........................ 1
........................ 1
.......................... 3
A
B
C
D
E
Procedimiento
Cassetto .................................................. 1
Viti M3 x 8 ................................................ 4
Vite M3 x 12............................................. 1
Etichetta del formato del cassetto............ 1
Copriforo.................................................. 3
A
B
C
D
E
Kassette................................................... 1
M3 x 8 Schrauben ................................... 4
M3 x 12 Schraube ................................... 1
Kassettengren-Etikett .......................... 1
Abdeckungsetikett ................................... 3
Italiano
A
B
C
D
E
Procdure
Casete ..................................................... 1
Tornillo M3 x 8 ......................................... 4
Tornillo M3 x 12 ....................................... 1
Etiqueta de tamao del casete ................ 1
Sello para orificios ................................... 3
Deutsch
A
B
C
D
E
Cassette .................................................. 1
Vis M3 x 8 ................................................ 4
Vis M3 x 12 .............................................. 1
tiquette au format cassette ...................... 1
Obturateur ............................................... 3
Espaol
A
B
C
D
E
Procedure
Cassette .................................................. 1
M3 8 screw ........................................... 4
M3 12 screw ......................................... 1
Cassette size label .................................. 1
Hole seal.................................................. 3
Franais
A
B
C
D
E
............................1
M3 8 .........................4
M3 12 ........................1
................1
........................3
MFP
OFF
A
2
1
A
2
2
1
1
2
1
Up to three cassettes can be stacked.
(For 22 ppm MFP models, no more than two
cassettes can be stacked.)
NOTICE
AVIS
AVISO
HINWEIS
NOTIFICA
22 ppm MFP 2
1. Place the main body directly down onto the cassettes by aligning the positioning insertion
sections (2) of the top cassette with the positioning pins (1) at the rear of the bottom cassette (A)
(only when stacking 2 or more cassettes).
When placing the main body on the cassettes, take care not to hit the main body against the
cassette pins or ground plate.
1. Placez directement le corps principal sur les cassettes en alignant les sections d'insertion de
positionnement (2) de la cassette suprieure avec les goupilles de positionnement (1) l'arrire
de la cassette (A) (dans le cas d'un empilage de 2 cassettes ou plus uniquement).
Lorsque le corps principal est plac sur les cassettes, attention ne pas le cogner le corps
principal contre les goupilles ou la plaque de terre de la cassette.
1. Coloque el cuerpo principal directamente sobre los casetes, alineando las secciones de
insercin de ubicacin (2) del casete superior con los pasadores de ubicacin (1), en la parte
posterior del casete inferior (A) (solo cuando se apilan 2 casetes o ms).
Cuando coloque el cuerpo principal sobre los casetes, tenga cuidado de no golpear el cuerpo
principal contra los pasadores o placa de fondo de los casetes.
1. Die Haupteinheit direkt auf die Kassetten setzen; dabei die Positionsstiftnuten (2) der oberen
Kassette auf die Positionsstifte (1) am hinteren Teil der unteren Kassette (A) ausrichten (nur bei
Stapeln von 2 oder mehr Kassetten).
Achten Sie beim Platzieren der Haupteinheit darauf, dass Sie nicht gegen die Kassettenstifte
oder die Bodenplatte stoen.
1. 2A1
2 2
2 2
3
MFP
22 2
1. (A) (1)
(A) (2)
1.
4
3
4
5
3
5
7
6
6
7
7
6
2. Place the main body directly down onto the cassettes by aligning the
positioning insertion sections of the main body (4) with the positioning
pins (3) at the rear of the cassette (A).
When placing the main body on the cassettes, take care not to hit the
main body against the cassette pins or ground plate.
3. Remove the screw (5) and pin (6) from each cassette and remove the
back covers (7).
3. Die Schraube (5) und den Stift (6) jeder Kassette entfernen und die
hinteren Abdeckungen (7) abnehmen.
2. 4A3
3. 567
3. (5)1 (6)1
(7)
11
10
7. Plug the connector (10) for the cassette (A) into the connector socket
(11).
7. Enchufe el conector (10) del casete (A) en el enchufe del conector (11).
4. 8
5. 9
6. 4 89
7. A1011
4. (8)1
5. (9)
6. 4 (8)1
(9)
14
A
A
13
12
8. Remove the connector cover (12) from the cassettes other than the
lowest cassette (A).
(only when stacking 2 or more cassettes)
9. Plug the connector (13) for the lower cassette (A) into the connector
socket (14) in the upper cassette (A).
(only when stacking 2 or more cassettes)
8. A12
2 2
9. A13A14
2 2
8. (A)
(12)
2
B
C
B
B
B
5
7
5
5
10. Secure each of the cassettes using three M3 x 8 screws (B) and one M3 x 12 screw (C).
Right: Two M3 x 8 screws (B)
Left: One M3 x 8 screw (B)
Rear: One M3 x 12 screw (C)
10. Fixez chacune des cassettes l'aide des trois vis M3 x 8 (B) et la vis M3 x 12 (C).
Droite : Deux vis M3 x 8 (B)
Gauche : Une vis M3 x 8 (B)
Arrire : Une vis M3 x 12 (C)
10. Asegure cada uno de los casetes por medio de tres tornillos M3 x 8 (B) y un tornillo M3 x 12 (C).
Derecha: dos tornillos M3 x 8 (B)
Izquierda: un tornillo M3 x 8 (B)
Atrs: un tornillo M3 x 12 (C)
10. Jede Kassette mit jeweils drei M3 x 8 Schrauben (B) und einer M3 x 12 Schraube (C) sichern.
Rechts: Zwei M3 x 8 Schrauben (B)
Links: Eine M3 x 8 Schraube (B)
Hinten: Eine M3 x 12 Schraube (C)
10. Fissare ciascuno dei cassettoni usando tre viti M3 x 8 (B) e una vite M3 x 12 (C).
Lato destro: due viti M3 x 8 (B)
Lato sinistro: una vite M3 x 8 (B)
Lato posteriore: una vite M3 x 12 (C)
10. 3
2
1
1
11.56
7
M3 8 B 1 M3 12 C
M3 8 B
M3 8 B
M3 12 C
11.(7) (5)1
(6)1
18
16
18
16
A
19
B
19
17
15
12.
13.15 3 16
17
14.A
2 2
15. 2 1819
2 2
19
16. M3 8 B
17.
12.
14. (A)
2
15. (18)2 (19)
2
(19)
16. M3 8(B)1
17.
20
E
20
20
D
D
D
Vrification du fonctionnement
Verifica di funzionamento
18.D
19.20
3
20.E
3
18.
(D)
19. 3
(20)
20. 3
(E)
ON
20r2.5mm
7 seg
[ ]
1. 034
1
: exp3
3
: exp4
4
: exp5
5
< > 20 2.5 mm a
1
2. b
c
-5.0-+10.0
1 0.1mm
3.
4. 2 31
7seg
1. U034
1
2
exp3
3
3
exp4
4
4
exp5
5
20 2.5mm
( (a) )
(1)
2. (b)
(c)
-5.0 +10.0
1 0.1mm
3.
4. (1)
2
3
20 2.5mm ( (a) )
7 seg
[ ]
1. 034
2
: exp3
3
: exp4
4
: exp5
5
2. b
c
-7.0-+10.0
1 0.1mm
3.
4. 2 31
7seg
1. U034
2
2 exp3
3
3 exp4
4
4
exp5
5
2.0mm
( (a)
(2)
10
2. (b)
(c)
-7.0 +10.0
1 0.1mm
3.
4. (2)
2
3
2.0mm ( (a) )
20r2.5mm
LCD
[ ]
1. 034
ADJ.RCL ON TIMING
:RCL T1
:RCL T2
:RCL T3
< > 20 2.5 mm a
1
2. b
c
-5.0-10.0
1 0.1mm
3.
4. 2 31
LCD
1. U034
ADJ, RCL ON TIMING
2 RCL T1
3 RCL T2
4 RCL T3
20 2.5mm
( (a) )
(1)
2. (b)
(c)
-5.0 +10.0
1 0.1mm
3.
4. (1)
2
3
20 2.5mm ( (a) )
11
LCD
[ ]
1. 034
ADJ.LSU OUT TIMING
:LSU T1
:LSU T2
:LSU T3
< > 2.0 mm a
2
LCD
1. U034
ADJ, LSU OUT TIMING
2 LSU T1
3 LSU T2
4 LSU T3
2.0mm ( (a) )
(2)
12
2. b
c
-0.7-+10.0
1 0.1mm
3.
4. 2 31
2. (b)
(c)
-7.0 +10.0
1 0.1mm
3.
4. (2)
2
3
2.0mm ( (a) )
English
Procedure
Procdure
Procedimiento
Verfahren
Procedura
Supplied parts
A Duplex unit............................................... 1
B M3 x 08 screw ......................................... 2
C Wire guide ............................................... 1
Franais
Pices fournies
A Unit recto-verso ..................................... 1
B Vis M3 x 08 .............................................. 2
C Guide cble ............................................ 1
Espaol
Partes suministradas
A Unidad dplex.......................................... 1
B Tornillo M3 x 08 ....................................... 2
C Gua para el cable ................................... 1
Deutsch
Gelieferte Teile
A Duplex-Einheit ......................................... 1
B M3 x 08 Schraube ................................... 2
C Kabelfhrung ........................................... 1
Italiano
Parti di fornitura
A Unit Duplex ............................................ 1
B Vite M3 x 08............................................. 2
C Guida cavi................................................ 1
A ........................1
B M3 08 ........................2
C ..........................1
MFP
OFF
5
6
1. (1)
2. (2) (3)
3. (4) (5)
4. (1)
5. (A) (6)
8
9
B
A
B
8
7
B
10
10
6. Mount the duplex unit (A) on the conveying guide (7) and push the
upper section in the direction of the arrow so that the 4 latches (8) fit
over the pawls (9).
6. (A) (7)
(8)4 (9)
7. (10) (A)
8. M3 08(B)2 (A)
14
13
12
C
11
9. Open the conveyer unit (11) and connect the connector (12) of the duplex unit (A) to the main
body.
10. Slot the wire guide (C) into latch (13) and then latch (14) on the main unit.
11. Reattach the removed parts to their original positions.
12. Close the conveyer unit (11) and left cover (1).
9. Ouvrez l'unit d'entranement (11) et connectez le connecteur (12) de l'unit recto-verso (A)
au corps principal.
10. Glissez le guide cble (C) dans le verrou (13) puis dans le verrou (14) de l'unit principale
11. .Remettez les pieces enlevees a leurposition d'origine.
12. Fermez l'unit d'entranement (11) et le couvercle gauche (1).
Vrification du fonctionnement
9. Abra la unidad transportadora (11) y conecte el conector (12) de la unidad duplex (A) en el
cuerpo principal.
10. Encajar la gua para el cable ( C ) en el pestillo (13) y, a continuacin, en el pestillo (14) de la
unidad principal.
11. Vuelva a instalar las piezas desmontadasen sus posiciones originales.
12. Cerrar la unidad transportadora (11) y la cubierta izquierda (1).
9. Die Frdereinheit ffnen (11), und den Steckverbinder (12) der Duplex-Einheit (A) an die
Haupteinheit anschlieen.
10. Schieben Sie die Kabelfhrung (C) in die Raste (13) und dann die Raste (14) an der
Haupteinheit
11. Die entfernten Teile wieder an ihrenursprunglichen Positionen anbringen.
12. Schlieen Sie die Frdereinheit (11) und die linke Abdeckung (1).
9. Aprire lunit convogliatore (11) e collegare il connettore (12) dellunit duplex (A) al corpo
principale.
10. Inserire la guida cavi (C) nel fermo (13), e quindi il fermo (14) sull'unit principale.
11. Rimontare le parti rimosse nelle loroposizioni originali
12. Chiudere l'unit convogliatore (11) e il coperchio sinistro (1).
Verifica di funzionamento
ON
20r2.5mm
Premere il tasto di modo della qualit dellimmagine finch Text non si illumina. (gruppo
1)
Premere il tasto di esposizione finch expl inizia a lampeggiare. (modo 6)
Premere il tasto di interruzione per eseguire i modelli di prova nel modo duplex e
controllare limmagine. <Valore di riferimento> Entro 20 2.5 mm (immagine
dell'esempio di copia (a))
Se lo scostamento supera il valore di riferimento, effettuare la seguente regolazione.
7seg
1. U034
1
exp1
20 2.5mm ( (a) )
2. (b)
(c)
-5.0 +10.0
1 0.1mm
3.
4. (1) 2 3
20 2.5mm ( (a) )
Premere il tasto di modo della qualit dellimmagine finch Text e Photo non si
illuminano. (gruppo 2)
Premere il tasto di esposizione finch expl inizia a lampeggiare. (modo 6)
Premere il tasto di interruzione per eseguire i modelli di prova nel modo duplex e
controllare limmagine. <Valore di riferimento> Entro 3.0 mm (immagine dell'esempio
di copia (a)
Se lo scostamento supera il valore di riferimento, effettuare la seguente regolazio.
7seg
1. U034
exp1
3.0mm ( (a) )
(2)
2. (b)
(c)
-7.0 +10.0
1 0.1mm
3.
4. (2) 2 3
3.0mm ( (a) )
20r2.5mm
Si lcart entre l'axe du papier (ligne pointille) et le trait de l'exemple de copie (2)
est suprieur la valeur de rfrence,effectuez le rglage suivant.
LCD
1. U034
ADJ, RCL ON TIMING
RCL DUP
20 2.5mm ( (a) )
2. (b)
(c)
-5.0 +10.0
1 0.1mm
3.
4. (1) 2 3
20 2.5mm ( (a) )
Whlen Sie ADJ, LSU OUT TIMING, und drcken Sie die Starttaste.
Whlen Sie LSU DUP.
Drcken Sie die Unterbrechungstaste, um das Testmuster im Duplexmodus
auszugeben, und berprfen Sie das Bild. <Bezugswert> Binnen 3,0 mm
(Kopienmuster (a) Bild).
Falls der Abstand zwischen der Mittenlinie des Papiers (Punktierte Linie) und der
Kopienmusterlinie (2) grer als der Bezugswert ist, ist die folgende Einstellung
durchzufhren.
LCD
1. U034
ADJ, LSU OUT TIMING
LSU DUP
3.0mm ( (a) )
(2)
2. (b)
(c)
-7.0 +10.0
1 0.1mm
3.
4. (2) 2 3
3.0mm ( (a) )
J
G
F
English
Supplied parts
A
B
C
D
Franais
Pices fournies
A
B
C
D
Espaol
Partes suministradas
A
B
C
D
Deutsch
Gelieferte Teile
A
B
C
D
Papierfrdereinheit .................................. 1
Hefterhilfsabdeckung ............................... 1
Hefterabdeckung ..................................... 1
Hakenhalter ............................................. 1
Italiano
Parti fornite
A
B
C
D
A
B
C
D
............................ 1
........................ 1
.......................... 1
................................ 1
A
B
C
D
........................1
................1
....................1
........................1
E
F
G
H
I
J
K
L
E
F
G
H
I
J
K
L
E
F
G
H
I
J
K
L
E
F
G
H
I
J
K
L
Finisher-Druckablage............................... 1
Obere linke Abdeckung ........................... 1
Frontauswurfabdeckung .......................... 1
Rckauswurfabdeckung .......................... 1
Finisher-Ablage........................................ 1
Heftklammermagazin............................... 1
1
Groer Stift .............................................. 1
E
F
G
H
I
J
K
L
E
F
G
H
I
J
K
L
................. 1
........................... 1
( ) ...................... 1
( ) ...................... 1
..................... 1
........................... 1
................................... 1
............................. 1
E
F
G
H
I
J
K
L
..............1
..........................1
........................1
........................1
..................1
..............1
............................1
..............................1
M Kleiner Stift............................................... 1
N M3 6 Schraube ..................................... 3
Entfernen Sie Klebeband und/oder
Dmpfungsmaterial vollstndig von den
mitgelieferten Teilen.
M ............................. 1
N M3 6 ......................... 3
M .............................. 1
N M3 6 ........................ 3
4
A
3
1
3
Important
Procedure
Important
Procdure
Importante
Procedimiento
Wichtig
Verfahren
Importante
Procedura
(A)
(A)
OFF
1. (1)
2. 1 (2) 3 (3)
(4)
1. (1)
2. (2)1 (3)3
(4)
10
8
9
9
9
9
5. Remove the 5 screws (9) from the rear side of the machine to remove
the cover (10).
5. Quitar los 5 tornillos (9) del lado trasero de la mquina para desmontar
la cubierta (10).
5. Die 5 Schrauben (9) von der Rckseite des Gerts entfernen, um die
Abdeckung (10) abzunehmen.
5. Rimuovere le 5 viti (9) dal lato posteriore della macchina per togliere il
coperchio (10).
3. 1 (5) (6)
4. 1 (7) (8)
5. 5 910
3. (5)1 (6)
4. (7)1 (8)
5. (9)5
(10)
12
16
14
14
14
15
13
11
6. (11)
7. 1213
12 6 14
8. (B) (15)
6. (11)
7. (12) (13)
(12)
14)6
17
L
Installing the paper conveying unit
9. Insert the paper conveying unit (A) from the machine front and slide it to the left.
10. Fix the paper conveying unit (A) using two pins.
Front: Use the large pin (L).
Rear: Use the small pin (M).
The grounding plate (17) must be in contact with the frame.
9. (A)
10. 2 (A)
(L)
(M)
17
9. (A)
10. (A) 2
(L)
(M)
(17)
20
21
22
K
D
19
18
Installation
11. Insrer le capot interne (K) en le glissant en place de sorte que le
verrou (18) et les 2 pattes (19) cliquent en position.
Instalacin
11. Instalar la cubierta interior (K) deslizndola por la ranura, hasta que el
pestillo (18) y las 2 lengetas (19) emitan un clic al llegar a su posicin.
Installieren
11. Passen Sie die innere Abdeckung (K) durch Einschieben so ein, dass
die Raste (18) und die 2 Laschen (19) hrbar einrasten.
Installazione
11. Montate il coperchio interno (K) inserendolo in modo che il fermo (18) e
le 2 linguette (19) si inseriscano a scatto in posizione.
11.1818 2 19
12. 1 (20)
13.D2120
14.D20
12. (20)
13. (D) (21) (20)
14. (D) (22)
(20)
24
24
23
25
A
D
E
15. Pass the wires (23) of the finisher process table (E) through the opening at the rear side of the machine.
16. Insert the finisher process table (E) from the front side of the machine and hang the hooks (24) on the right and left of the table (E) onto
the machine.
Left: Fit the hook into the latch (25) on the paper conveying unit.
Right: Fit the hook into the hook holder (D).
15. Faire passer les connecteurs (23) de la table de processus du module de finition (E) par louverture du ct arrire de la machine.
16. Insrez la table de processus du module de finition (E) depuis lavant de la machine, et suspendez sur la machine les crochets (24) se
trouvant sur les cts droit et gauche du plateau (E).
Gauche : insrer le crochet dans le verrou (25) sur l'unit de transport du papier.
Droite : insrer le crochet dans le support de crochet (D).
15. Pase los conectores (23) de la tabla de proceso de finalizador (E) por la abertura en el lado trasero de la mquina.
16. Inserte la tabla de proceso de finalizador (E) por el lado delantero de la mquina y cuelgue los ganchos (24) en los lados derecho e izquierdo
de la tabla (E) de la mquina.
Izquierda: colocar el gancho en el pestillo (25), en la unidad de transporte de papel.
Derecha: colocar el gancho en el soporte de gancho (D).
15. Die Steckverbinder (23) der Finisher-Druckablage (E) durch die ffnung auf der Rckseite der Maschine fhren.
16. Die Finisher-Druckablage (E) von der Vorderseite der Maschine einfhren, und die Haken (24) auf der rechten und linken Seite der Ablage (E)
in die Maschine einhngen.
Links: Setzen Sie den Haken in die Raste (25) an der Papierfrdereinheit.
Rechts: Setzen Sie den Haken in den Hakenhalter (D) ein.
15. Fate passare i connettori (23) della tabella di elaborazione del finitore (E) atttraverso lapertura sul lato posteriore della macchina.
16. Inserite la tabella di elaborazione del finitore (E) dal lato anteriore della macchina e appendete i ganci (24) a destra e a sinistra del tabella (E)
sulla macchina.
Sinistra: inserite il gancio nel fermo (25) sull'unit di trasporto carta.
Destra: inserite il gancio nel supporto a gancio (D).
15. (E) 23
16. (E) (24)
25
D
29
31
28
32
30
26
27
17. At the rear side of the machine, connect the connector (26) of the
finisher process table to the connector (27) of the paper conveying unit.
18. Connect the connector (28) of the finisher process table to YC4 (29) on
the engine PWB.
19. Run the wires through the clamp (30).
20. Refit the cover (10) removed in step 5 using 5 screws (9)
17. Sul lato posteriore della macchina, collegate il connettore (26) della
tabella di elaborazione del finitore al connettore (27) dellunit di
trasporto della carta.
18. Collegate il connettore (28) della tabella di elaborazione del finitore al
YC4 (29) sul motore PWB.
19. Passate i cavi attraverso la fascetta (30).
20. Ricollocare il coperchio (10) rimosso al passo 5 utilizzando le 5 viti (9).
17. (26)
(27)
18. (28) YC4(29)
19.30
20. 5 9 5 10
17. (26)
(27)
18. (28)
YC4(29)
19. (30)
20. 5 (10) (9)5
22. (31)
F
33
33
C
33
34
2
Attaching the upper left cover
23. Slot the 6 clips (33) on the upper left cover (F) into place and slide the
cover to the front.
24. Fit the latch (34) to attach the upper left cove
23. 6 33F
24.34
25. 2 (C)
2 1 (2)
1 M3 6(N)
26. (11) (1)
23.(F) (33)6
24. (34)
(F)
25. 2 (C)
2 (2)1
M3 6(N)1
26.(11) (1)
I
N
35
35
N
H
G
G
Attaching the finisher tray
27. Fix the front eject cover (G) and the rear
eject cover (H) using an M3 6 screw (N)
each.
28. Insert the front and rear hooks (35) of the finisher tray (I) into the front eject cover (G) and the
rear eject cover (H) respectively and then attach the finisher tray (I).
28. Insrez les crochets (35) avant et arrire du plateau du module de finition (I) dans le capot
djection avant (G) et dans le capot djection arrire (H) respectivement, puis fixez le
plateau du module de finition (I).
28. Inserte los ganchos (35) delantero y trasero de la bandeja de finalizador (I) en la cubierta de
expulsin frontal (G) y la cubierta de expulsin trasera (H) respectivamente y coloque la
bandeja de finalizador (I).
28. Die vorderen und hinteren Haken (35) der Finisher-Ablage (I) jeweils in die
Frontauswurfabdeckung (G) und die Rckauswurfabdeckung (H) einfhren, und dann die
Finisher-Ablage (I) anbringen.
28. Inserite i ganci (35) anteriori e posteriori del vassoio del finitore (I) rispettivamente nel
coperchio anteriore di espulsione carta (G) e nel coperchio posteriore di espulsione carta (H)
e poi montate il vassoio del finitore (I).
10
36
Vrification du fonctionnement
Verifica di funzionamento
29.(36)
(J)
30.(36)
1.
2.
1.
ON
2.
11
C
D
English
Supplied parts
A
B
C
D
Job separator........................................... 1
LED PWB unit.......................................... 1
Tray holder............................................... 1
Job separator tray.................................... 1
Franais
Pices fournies
A
B
C
D
Espaol
Partes suministradas
A
B
C
D
Deutsch
Gelieferte Teile
A
B
C
D
Job-Separator .......................................... 1
LED-Platineneinheit................................. 1
Fachhalter................................................ 1
Job-Separator-Fach................................. 1
Italiano
Parti di fornitura
A
B
C
D
A
B
C
D
E
F
G
H
E
F
G
H
E
F
G
H
E
F
G
H
E
F
G
H
E
F
G
H
........................... 1
............................. 1
............................. 1
M3 8 ......................... 1
E
F
G
H
..........................1
..............................1
..............................1
M3 8 .........................1
.......................... 1
LED ...................... 1
.............................. 1
...................... 1
A
B
C
D
....................1
LED ....................1
........................1
..............1
4
3
1
3
Procedure
Before installing the job separator, be sure to
turn the main power switch of the machine off
and unplug the power cable from the wall outlet.
Procdure
Avant dinstaller le sparateur de travaux, veillez
mettre la machine hors tension et
dbrancher le cble dalimentation de la prise
murale.
Procedimiento
Antes de instalar el separador de trabajos,
asegrese de desconectar el interruptor
principal de la mquina y desenchufar el cable
elctrico del tomacorriente de la pared.
Verfahren
Schalten Sie unbedingt den Betriebsschalter der
Maschine aus, und trennen Sie das Netzkabel
von der Netzsteckdose, bevor Sie den JobSeparator installieren.
Procedura
Prima di installare il separatore lavori,
assicurarsi di spegnere linterruttore principale
di alimentazione della macchina e scollegare la
spina del cavo di alimentazione dalla presa a
muro della rete elettrica.
OFF
1. (1)
2. 1 (2) 3 (3)
(4)
1. (1)
2. (2)1 (3)3
(4)
10
8
9
9
9
9
5. Remove five screws (9) from the rear side of the machine to remove
the cover (10).
5. Togliete la vite (9) dal lato posteriore della macchina per rimuovere il
coperchio (10).
3. 1 (5) (6)
4. 1 (7) (8)
5. 5 (9) (10)
3. (5)1 (6)
4. (7)1 (8)
5. (9)5
(10)
11
6. (A)
7. 2 (A)
(F)
(G)
11
6. (A)
7. (A) 2
(F)
(G)
(11)
15
16
13
12
14
8. Connect the connector (12) at the rear of the job separator to YC4 (13)
on the engine PWB.
9. Run the wires through the clamp (14).
10. Loosen the screw (15) to make the drive unit (16) of the job separator
ready for starting to drive.
11. Tighten the screw (15).
12. Refit the cover (10) using six screws (9) removed in step 5.
10. Allentare la vite (15) per preparare lunit guida del separatore lavori al
funzionamento.
11. Stringere la vite (15).
12. Rimettete a posto il coperchio (10) utilizzando la vite (9) rimossa nel
passo 5.
8. (12) YC4(13)
9. 14
10. 1 (15)
11. 1 (15)
12. 5 (10) 5 (9)
8. (12) YC4(13)
9. (14)
B
18
17
H
19
C
Attaching the LED PWB unit
13.Run the connector (17) from the job separator through the opening in the LED PWB unit (B) and
plug it into the connector (18).
14.Fix the LED PWB unit (B) using the M3 8 screw (H).
LED
13.17 LED B18
14. 1 M3 8(H) LED (B)
LED
13. (17) LED (B) (18)
20
C
21
16.Install the job separator tray (D) from the front side of the machine.
Left: Insert the tray into the groove (20).
Right: Hang the hook (21) on the tray holder (C).
16.Installare il vassoio del separatore lavori (D) dal lato anteriore della macchina.
Lato sinistro: inserire il vassoio nellincavo (20).
Lato destro: appendere il gancio (21) sul supporto del vassoio (C).
16. (D)
(20)
(21) (C)
16. (D)
(20)
(21) (C)
2
Installing the left front cover
17.Install the left front cover (E) using the screw
(2) removed in step 2.
18.Close the front cover (1).
Vrification du fonctionnement
Verifica di funzionamento
17. 2 1 (2)
(E)
18. (1)
17. 2 (2)1
(E)
18.(1)
1.
2.
1.
ON
2.
3.
3.
G
I
Supplied parts
A Fax control circuit board assembly .......... 1
B Modular cord (100 V, 120 V, 220 V
specifications and for Australia)
120 V item 303HZ4501 (UL Listed. Chaus,
Type CS) ................................................. 1
C M3 x 8 screw .......................................... 9
Franais
Pices fournies
A Ensemble de carte circuits de
commande de fax.................................... 1
B Cordon modulaire (spcifications 100 V,
120 V, 220 V et pour lAustralie) .............. 1
C Vis M3 x 8 ................................................ 9
D Ressort lames....................................... 1
Espaol
Partes suministradas
A Conjunto de la tarjeta de circuitos de
control de facsmil ........................................ 1
B Cable modular (especificaciones de 100 V,
120 V, 220 V y para Australia) ..................... 1
C Tornillo M3 x 8 .............................................. 9
D Resorte de la placa ...................................... 1
Deutsch
Gelieferte Teile
A Faxsteuerplatineneinheit ......................... 1
B Modulkabel (100-, 120-, 220-VSpezifikationen und fr Australien).......... 1
C M3 8 Schraube ..................................... 9
D Tellerfeder................................................ 1
E Kabel ....................................................... 1
Italiano
Parti fornite
A Gruppo scheda a circuiti di controllo fax.. 1
B Cavo modulare (per modelli con specifica
100 V, 120 V, 220 V e per lAustralia)...... 1
C Vite M3 x 8............................................... 9
D Molla della piastra.................................... 1
E Cavo ........................................................ 1
A FAX .................. 1
B
100V,120V,220V
) ................. 1
C M3 8 ........................... 9
D ................................ 1
M
P
English
D
E
F
G
H
Plate spring.............................................. 1
Wire ......................................................... 1
Upper plate .............................................. 1
Lower plate .............................................. 1
Operation section sheet
120 V specification .................................. 4
230 V specification .................................. 8
I One-touch securing sheet........................ 1
J Fax plate .................................................. 1
K One-touch sheet
120 V specification ....................................... 3
230 V specification ....................................... 7
L One-touch label sheet .................................. 1
M Fax label sheet
(120 and 230 V specifications only) ............. 1
N FCC68 label (120 V specification only) ........ 1
O JATE label (100 V specification only) ........... 1
P Modular connector cover
(for New Zealand only)................................. 1
E
F
G
H
Cble ....................................................... 1
Plateau suprieur..................................... 1
Plateau infrieur....................................... 1
Feuille de la section dopration
spcifications 120 V ................................ 4
spcifications 230 V ................................ 8
I Feuille de fixation touche unique .......... 1
J Plaque de fax........................................... 1
E
F
G
H
Cable.............................................................1
Placa superior ...............................................1
Placa inferior .................................................1
Hoja de seccin de funcionamiento
especificaciones para 120 V.........................4
especificaciones para 230 V.........................8
I Hoja de seguridad de un toque.....................1
J Placa de facsmil...........................................1
K Hoja de un toque
especificaciones para 120 V......................... 3
F Obere Platte............................................. 1
G Untere Platte............................................ 1
H Bedienteilfolie
120-V-Spezifikation.................................. 4
230-V-Spezifikation.................................. 8
I Schnellhaftfolie ........................................ 1
J Faxplatte .................................................. 1
K Schnellfolie
120-V-Spezifikation.................................. 3
230-V-Spezifikation.................................. 7
L Schnelletikettenfolie ................................. 1
M Faxetikettenfolie
(nur fr Modelle 120 und 230 V).............. 1
N FCC68-Etikett (nur 120-V-Spezifikation) .. 1
O JATE-Etikett (nur 100-V-Spezifikation)..... 1
P Modulsteckerabdeckung
(nur fr Neuseeland)................................ 1
F Piastra superiore...................................... 1
G Piastra inferiore........................................ 1
H Foglio della sezione di funzionamento
modelli con specifica 120 V ..................... 4
modelli con specifica 230 V ..................... 8
I Foglio di fissaggio a un tocco .................. 1
J Piastra del fax .......................................... 1
K Foglio a un tocco
modelli con specifica 120 V ..................... 3
E
F
G
H
120V ..........................
230V ..........................
L ................
M FAX 120V,230V ...
N FCC68 120V ............
O JATE
100V .............
P
................
..................................
............................
............................
120V .........................
230V .........................
I ..................
J FAX ..........................
K ......................
1
1
1
4
8
1
1
1
3
7
1
1
1
1
1
Option
Q Memory module DIMM (32 MB) .............. 1
Option
Q Module de mmoire DIMM (32Mo) .......... 1
Opcin
Q Mdulo de memoria DIMM (32MB) ......... 1
Option
Q Speichermodul (DIMM, 32MB) ................ 1
Opzione
Q Modulo di memoria DIMM (32MB)........... 1
Q DIMM
32MB) ................... 1
Procedure
Procdure
Procedimiento
Verfahren
Procedura
MFP
OFF MFP
2
4
Q
2
4
4
4
3. (4)5
(5)
E
D
8
A
6
4. (6) 1 (7)
(8)
5. M3 8(C)1 (D)
FAX
6. (E) FAX
(A) YC1(9)
10
12
12
11
11
7. Plug the white connector on the wire (E) into YC10 (10) on the engine
circuit board.
8. Fit the 2 hooks (11) on the fax control circuit board assembly (A) into
the latch (12) in the shielding cover.
7. Den weien Steckverbinder des Kabels (E) in Buchse YC10 (10) der
Motorplatine stecken.
7. Collegare il connettore bianco sul cavo (E) nel YC10 (10) sulla scheda
di circuito principale.
8. Inserire i 2 ganci (11) sul gruppo scheda a circuiti di controllo fax (A) nel
fermo (12) del coperchio di schermatura.
7. (E) YC10(10)
C
13
14
C*
C
C*
A
13
C*
9. Secure the fax control circuit board assembly (A) using the five M3 x 8 screws (C).
When fastening the lower-right screw (C*), take care not to pinch the wire (13)
9. Fixez l'ensemble de carte circuits de commande de fax (A) l'aide de cinq vis M3 x 8 (C).
En fixant la vis infrieure droite (C*), attention ne pas pincer le cble (13).
9. Asegurar el conjunto de la tarjeta de circuitos de control de facsmil (A) por medio de los cinco
tornillos M3 x 8 (C).
Cuando ajuste el tornillo inferior derecho (C*), tenga cuidado de no atrapar el cable (13).
9. Fissare il gruppo scheda a circuiti di controllo fax (A) utilizzando le cinque viti M3 x 8 (C).
Quando si fissa la vite (C*) in basso a destra, prestare attenzione di non prendere il cavo (13).
10. (14)1
14
16
C
15
17
11. Attach the upper plate (F) using an M3 x 8 screw (C) and another
screw (14).
12. Attach the lower plate (G) using two M3 x 8 screws (C).
13. Refit the cover (5) removed in step 3 using 5 screws (4).
11. Fixez le plateau suprieur (F) l'aide d'une vis M3 x 8 (C) et d'une
autre vis (14).
12. Fixez le plateau infrieur l'aide de deux vis M3 x 8 (C).
13. Rinstallez le capot (5) dpos l'tape 3 l'aide de 5 vis (4).
11. Instalar la placa superior (F) por medio de un tornillo M3 x 8 (C) y otro
tornillo (14).
12. Instalar la placa inferior (G) por medio de dos tornillos M3 x 8 (C).
13. Volver a colocar, con los 5 tornillos (4), la cubierta (5) desmontada en
el paso 3.
11. Die obere Platte (F) mittels einer M3 x 8 Schraube (C) und einer
weiteren Schraube (14) befestigen.
12. Die untere Platte (G) mittels zwei M3 x 8 Schrauben (C) befestigen.
13. Die in Schritt 3 entfernte Abdeckung (5) mittels der 5 Schrauben (4)
wieder anbringen.
L
14. L(15) (16)
100V,120V,220V
(B)
20
19
21
18
18
17.Lift the three pawls (20) and remove the operation section sheet cover
(21).
15.(18)
16.(19)
H
21
23
22
23
18. Remove the operation section sheet (22) and replace it with the
operation section sheet (H) for fax of the corresponding language.
18. Die Bedienteilfolie (22) entfernen und durch die Bedienteilfolie (H) fr
Fax der entsprechenden Sprache ersetzen.
18
24
I
20. Refit the cover (18) removed in step 15 by
inserting the pawl (24) into its slot.
21. (I)
22.
(I)
23. (I)
10
25
25
FAX (120V/230V )
24. FAX (M) FAX
(1) (4) FAX (J)
FAX (120V/230V )
25.FAX (J) (25)
26.FAX (J)
11
26
27. Sparez la feuille touche unique (K) pour la langue supporte en 2 parties
et les coller aux endroits respectifs sur la feuille de fixation touche unique
(I).
Remettre en place le couvercle gauche (19) de la section dopration que
lon avait retir auparavant lors de la procdure 16, la feuille de la section
dopration (22) que lon avait retire auparavant lors de la procdure 18, la
feuille de la section dopration pour fax (H) qui correspond aux langues
non utilises, et la feuille touche unique (K).
(120V/230V )
27. (K) 2
(I)
16 (19) 18
(22) FAX (H) (K)
(100V )
28.
(L) (26)
12
N/O
5
Attach the certification label (only 100V and
120 V).
29. Stick the FCC68 label (N) or JATE label (O)
onto the cover (5) after first cleaning the area
with alcohol.
In Australia or New Zealand, refer to page 14
to attach the label.
100V
120V
29.(5) FCC68 (N) JATE
(O)
P.14
U601U602
FAX
13
A-TICK label
TELEPERMIT label
14
A
A
1
GUIDE DINSTALLATION
DU Scan System (F)B
Espaol
GUIA DE INSTALACION
PARA EL Scan System (F)B
Deutsch
INSTALLATIONSANLEITUNG
FUR Scan System (F)B
Italiano
DUIDA ALLINSTALLAZIONE
PEL Scan System (F)B
Scan System(F)B
Scan System(F)B
CN5
YC12
CN5
Supplied parts
3. Remove the two screws (5) and remove the shield cover (6).
A Scanner board..........................................1
B Push plate ................................................1
C M3 x 8 screw ............................................1
Franais
YC12
A
English
11
10
6
A
YC12
CN5
1
4
4. Insert the scanner board (A) into the OPT1 opening (7) of the shield box and firmly push the CN5
connector (8) on the scanner board (A) all the way into the YC12 connector (9) on the engine circuit board.
Note
Ensure that the cable (10) is not pinched between the connectors.
Ensure that the film (11) is not trapped on the inside of the scanner board (A).
Pices fournies
A Carte de lecture........................................1
B Plaque de pousse ..................................1
C Vis M3 x 8 ................................................1
4. Insrer la carte scanner (A) dans louverture OPT1 (7) de la bote de blindage et pousser fermement le connecteur CN5 (8) de la carte scanner (A) fond dans le connecteur YC12 (9) de la
carte circuits du moteur.
Remarque
Vrifiez que le cble (10) n'est pas pris entre les connecteurs.
Vrifiez que le film (11) n'est pas prisonnier l'intrieur de la carte de lecture (A).
Piezas suministradas
A Tarjeta de escner....................................1
B Placa de empuje ......................................1
C Tornillo M3 x 8 ..........................................1
4. Inserte la tarjeta de escner (A) en la abertura OPT1 (7) de la caja de blindado y empuje firmemente el conector CN5 (8) en la tarjeta de escner (A) hasta el fondo en el conector YC12 (9) en
la tarjeta de circuitos del motor.
Nota
Asegrese de que el cable (10) no quede pinzado entre los conectores.
Asegrese de que la pelcula (11) no quede atrapada en el interior de la tarjeta de escner (A).
Gelieferte Teile
3. Die zwei Schrauben (5) entfernen und die Abschirmungsabdeckung (6) abnehmen.
A Scannerkarte............................................1
B Andruckplatte ...........................................1
C M3 8 Schraube......................................1
Scannerkarte installieren
4. Die Scannerkarte (A) in die ffnung OPT1 (7) der Abschirmungsbox einfhren, und den Steckverbinder CN5 (8) der Scannerkarte (A) mit festem Druck bis zum Anschlag in den Steckverbinder
YC12 (9) der Motorplatine einschieben.
Hinweis
Darauf achten, dass das Kabel (10) nicht zwischen den Steckverbindern eingeklemmt wird.
Darauf achten, dass der Film (11) nicht auf der Innenseite der Scannerkarte (A) hngen bleibt.
Parti fornite
Rimuovere i coperchi
A ........................... 1
B ............................. 1
C M3 x 8 ......................... 1
1. 5 1
2
2. 34
* OFFMFP
MFP
A ....................... 1
B ............................. 1
C M3 8......................... 1
*
MFP OFF
MFP
1. (1)5
(2)
2. (3) (4)
4. Inserire la scheda scanner (A) nellapertura OPT1 (7) della scatola di protezione e spingere stabilmente il connettore CN5 (8) della scheda scanner (A) fino in fondo nel connettore YC12 (9) sulla
scheda a circuiti del motore.
Nota
Assicurarsi che il cavo (10) non rimanga incastrato tra i connettori.
Assicurarsi che la pellicola (11) non rimanga impigliata all'interno della scheda scanner (A).
3. 2 56
5. M3 x 8 C
B6
4. A OPT1 7A CN5 8
YC12 9
10
11A
3. (5) (6)
(10)
(11) (A)
5.
(6)
(B) M3 8(C)
2009. 4
303JR56710
1
1
6
6
A
3
1
1
2
8. Refit the cover (2) removed in step 1 using 5
screws (1).
7. Fasten the scanner board (A) onto the shield box cover using the two screws (3) that have been
removed by Procedure 2
Installer le couvercles
6. Installez le couvercle de blindage (6) de sorte que la garniture de la plaque de pousse soit en
contact avec le IC de la carte de lecture (A) et fixez le couvercle en place l'aide des deux vis (5)
dposes l'tape 3.
7. Fixer la carte scanner (A) au couvercle de la bote de blindage laide des deux vis (3) que lon
avait retires auparavant lors de la procdure 2.
Instale la cubiertas
6. Instale la cubierta blindada (6) de forma tal que la junta de la placa de empuje quede en contacto
con el IC de la tarjeta de escner (A) y fije la cubierta en posicin por medio de los dos tornillos (5)
quitados en el paso 3.
7. Apriete la tarjeta de escner (A) en la cubierta de la caja de blindadi utilizando los dos tornillos (3)
que fueron sacados por el Procedimiento.
Installare il coperchi
6. Installare il coperchio di protezione (6) in modo che la guarnizione della piastra di spinta sia a
contatto con l'IC della scheda scanner (A) e fissare il coperchio in posizione usando le due viti (5)
rimosse nel passo 3.
7. Fissare la scheda scanner (A) al pannello della scatola di protezione a mezzo delle due viti (3) che
sono state rimosse nella procedura 2.
6. 6AIC 3 2
5
7. 3A
6. (A) IC (6)
3 (5)2
7. 2 (3)2 (A)
8. Die in Schritt 1 entfernte Abdeckung (2) mittels der 5 Schrauben (1) wieder anbringen.
8. 5 1 1
2
8. 1 (2) (1)5
2009. 4
303JR56710