Professional Documents
Culture Documents
Wi-Fi CPE Configuration Manual
Wi-Fi CPE Configuration Manual
BM632w
1
CPE Configuration
WiMAX CPE can be configured in two modes:
2. Route mode: In this mode the users enter WiMAX ID and password only once and afterwards they will be automatically
connected to the Internet simply by connecting the CPE to the computer.
Does change in the mode change my tariff plan?
No, mode change is part of CPE configuration.
Should I pay extra amount for mode change?
No. You are not supposed to pay any extra amount for mode change.
1. Bridge mode: In this mode the users should enter the WiMAX ID and password in WiMAX Portal each time they use the
service.
If your CPE model is BM632w, use the following way to change the mode:
At first, set your IP configuration to manual. To do so, go to Control Panel from Start menu.
Click on Local Area Connection of your network card and follow the instructions.
1
3
4
For Wi-Fi CPE (BM632w), enter 192.168.1.* for IP Address and 255.255.255.0 for Subnet Mask.
* any figure from 2 to 254.
2
7
Open your web browser and type http://192.168.1.1 in the address bar.
In the opened page, write admin for both Username and Password.
From the left menu, choose Basic and then WAN. Choose Route from Mode menu and click Apply.
1
2
3
4
5
Click Security from the left menu and then go to WiMAX and enter the following information.
PKM: PKMv2_EAP
Authentication: TTLS
(Change TLS to TTLS)
Inner EAP: MSCHAPv2
Change domain from Irancell.ir to mtnirancell.com
NAI: Macaddress@mtnirancell.com
Mac address is provided in this window. If not, go to page 24.
Please enter MAC Address without any space or colon
User ID: WiMAXID@mtnirancell.com
User Password: *******
(Password was sent to you at registration by Email and SMS).
3
1
2
4
5
10
3
4
1
11
Finally, bring back your IP configuration to automatic mode. To do so, click on Local Area Connection of your network
card and follow the instructions.
1
3
4
12
3
The CPE is ready to use. Open your browser and start surfing the net.
13
How can I change CPE configuration from Route mode to Bridge mode?
If your CPE model is BM632w, use the following way to change the mode:
At first, set your IP configuration to manual. To do so, go to Control Panel from Start menu.
14
15
Click on the Local Area Connection of your network card and follow the instructions.
1
3
4
16
For Wi-Fi CPE (BM632w), enter 192.168.1.* for IP Address and 255.255.255.0 for Subnet Mask.
* any figure from 2 to 254.
17
18
Open your web browser and type http://192.168.1.1 in the address bar.
In the opened page, write admin for both Username and Password.
From the left menu, choose Basic and then WAN. Choose Bridge from Mode menu and click Apply.
1
2
3
4
5
19
Click Security from the left menu and then go to WiMAX and enter the following information.
PKM: PKMv2_EAP
Authentication: TLS
(Change TTLS to TLS)
Change domain from Irancell.ir to irancell.com
NAI: Macaddress@irancell.com
3
4
1
2
20
3
4
1
21
Finally, bring back your IP configuration to automatic mode. To do so, click on Local Area Connection of your network
card and follow the instructions.
1
3
4
22
3
The CPE is ready to use. Open your browser, go to portal and enter WiMAX ID and password.
23
Go to Status (left menu) and then click Device. Your MAC ID is shown in front of WAN MAC Address.
1
2
3
24
25