Professional Documents
Culture Documents
Industrial Corrosion and Corrosion Control Technology (H. M. Shalaby - A. Al-Hashem - M. Lowther - J. Al-Besharah)
Industrial Corrosion and Corrosion Control Technology (H. M. Shalaby - A. Al-Hashem - M. Lowther - J. Al-Besharah)
H.M. Shalaby
A. Al-Hashem
M. Lowther
J. Al-Besharah
(Editors)
Published By
Kuwait Institute for Scientific Research
Sponsored by the Kuwait Institute for Scientific Research (KISR), the Kuwait
Foundation for the Advancement of Science (KFAS), the Kuwait National
Petroleum Company (KNPC), the Kuwait Oil Company (KOC), Ministry of
Electricity and Water (MEW), Kuwait University (KU), Ministry of Oil (MO),
the Gulf Cooperation Council-General Secretariat (GCC), Kuwait Chemical
Society (KCS), Organization of Arab Petroleum Exporting Countries (OAPEC),
and Petrochemical Industries Company (PIC).
Editors
H.M. Shalaby, A. Al-Hashem, M. Lowther and J. Al-Besharah
Published by
Kuwait Institute for Scientific Research
P.O. Box 24885, 13109 Safat, Kuwait
Publication Number: KISR 4890
FOREWORD
The 2nd Arabian Corrosion Conference was held in the state of Kuwait during the period 1215 October, 1996 under the auspices of H.H. Sheikh Saad Al-Abdullah Al-Salem Al-Sabah,
Kuwaits Crown Prince and Prime Minister. The present conference was scheduled to be
held in Kuwait during 27-30 April, 1991, however, it was postponed due to the events that
encompassed Kuwait and the Gulf region in 1990-1991.
The 1st Arabian Corrosion Conference was held in Kuwait during 4-8 February, 1984. It was
attended by over 300 scientists and engineers, representing 26 countries. The conference
proceedings were published in two volumes by Pergamon Press under the title Corrosion:
Industrial Problems, Treatment and Control Techniques. The conference provided a forum
for the exchange of ideas between scientists and engineers from the region with their
counterparts from the industrialized countries.
The patronage of the present conference, the organizing bodies, and the emphasis on
industrial corrosion and corrosion prevention reflect the keen interest of the countries in the
region in actively combating corrosion problems. This also reflect the recognition of the
economic impact resulting from the corrosion of materials.
Kuwait and the other Arab countries rely heavily on the utilization of metallic materials in
their oil-based industries. Seawater derived from the Arabian Gulf is used in water
desalination and as an industrial cooling media. The salinity of the Arabian Gulf seawater is
very high when compared to other seawater bodies. The Arabian Gulf countries are located in
an arid environmental zone where the temperature during the summer months could reach
50oC and the humidity during the autumn season could become 80% in some of the Gulf
states. All these factors contribute to the enhancement of the rate of corrosion of metals
and/or cause unpredictable service failures.
The program of the present conference includes a field visit to one of Kuwaits modern
refineries and a trip to one of Kuwaits oil fields. The success of the conference is perhaps
difficult to assess. However, the quality of the papers in this volume provides some
indication.
The Editors
PREFACE
The technical program of the present conference includes five plenary lectures and fifty three
scientific presentations from about twenty two countries. A number of honorary speakers,
carefully selected from high ranking officials and policy makers, were also invited to address
the conference. The honorary speakers are expected to provide an overview of the magnitude
of corrosion related problems in the Middle East as well as the avenues of linkage between
corrosion science and industrial applications. The conference papers were carefully selected
to include a blend of fundamental and applied research, and industrial experience. Such a
blend was thought to be essential for providing the participants from both industry and
academia with a chance to become familiar with the challenges facing each group and the
preventive actions to meet them. The papers were refereed in terms of scientific and
technical content and format in accordance with internationally accepted standards.
The papers in the proceedings are grouped in the following sections for quick reference:
Plenary Lectures
Oil Field Corrosion
Corrosion in Refinery and Petrochemical Industries
Seawater Corrosion
Corrosion in the Building Industry
Fundamental Aspects
Corrosion Protection and Monitoring
Corrosion Management
Novel Techniques
The plenary papers are mostly reviews covering important topic related to the objectives of
the conference. The remaining papers cover various topics of major importance to corrosion
in general and particularly to the oil-based and desalination industries. A good number of
papers delt with corrosion protection and new techniques for corrosion monitoring.
The task of editing this volume was facilitated by the efforts of the International Advisory
Committee and the Scientific Committee for the conference who reviewed all the papers. The
editorial board gratefully acknowledge these efforts; the cooperation, time and effort of all
authors ; and the management of the Kuwait Institute for Scientific Research for allocating
the required resources to prepare the manuscript of this volume.
The Editors
vi
TABLE OF CONTENTS
Foreword............................................................................................................................................v
Preface...............................................................................................................................................vi
Organizing Committees......................................................................................................................xi
Acknowledgement.............................................................................................................................xii
PLENARY LECTURES
Corrosion Management
V. Ashworth........................................................................................................................................1
The Deterministic Prediction of Damage
D.D. Macdonald...............................................................................................................................17
Relevance of Laboratory Corrosion Tests in Corrosivity Assessment
and Materials Selection: Case Studies
R.D. Kane.........................................................................................................................................37
Corrosion of Condensers in Multi Stage Flash
Evaporation Distillers
A.M. Shams El Din...........................................................................................................................49
Correct Materials Selection for Desalination
-The Key To Plant Reliability
J.W. Oldfield....................................................................................................................................67
OIL FIELD CORROSION
Corrosivity Prediction for Co2/H2s Production Environments
S. Srinivasan and R.D. Kane.............................................................................................................89
Testing of Drilling Fluids Formulated From Tabuk Formation Clays
M.N.J. Al-Awad, A.S. Dahab and M.E. El-Dahshan........................................................................111
Preventing Sulfate Scale Deposition in Oil Production Facilities
C.J. Hinrichsen, M.J. McKinzie, S. He, J. Oddo, A.J. Gerbino, A.T. Kan, and M.B. Tomson...........127
Concerns Over the Selection of Biocides for Oil Fields and Power Plants:
A Laboratory Corrosion Assessment
J. Alhajji and M. Valliappan...........................................................................................................135
Evaluation of Microbially Influenced Corrosion Risks and Control Strategies
in Seawater and Produced Water Injection Systems, Kuwait
P.F. Sanders, M. Salman and K. Al-Muhanna.................................................................................149
Hydrogen Degradation of Steel - Diffusion and Deterioration
M. Farzam...................................................................................................................................................165
Control Strategies for Thermophilic Sulphate-Reducing Bacteria
P.F. Sanders, H.M. Lappin-Scott and C.J. Bass...............................................................................179
Corrosion Evaluation of Austenitic and Duplex Stainless Steels in Simulated
Hydrogen Sulphide Containing Petrochemical Environments
K. Saarinen and E. Hamalainen......................................................................................................191
vii
ix
Author Index...................................................................................................................................677
Subject Index..................................................................................................................................679
ORGANIZING COMMITTEE
Jasem Al-Besharah
Khaled Al-Muhailan
Abdulhameed Al Hashem
Hamdy M. Shalaby
Abbas Ali Khan
Hussain Shareb
Jamal Al-Hajji
Khaled Shehab
Khalifa Al-Feraij
Abdel Monem Bedair
Mohammad Ashkanani
Mohammad Al-Rasheed
Mohammed Al-Qalaf
Abdul Khaliq Mustafa
Khawla Al-Rifaee
Chairman
Rapporteur
Coordinator
Member
Member
Member
Member
Member
Member
Member
Member
Member
Member
Member
Member
KISR
KFAS
KISR
KISR
KFAS
OAPEC
KU
KNPC
MEW
PIC
KOC
GCC
KCS
KISR
MO
Member
Member
Member
Member
UAE
UK
USA
USA
Chairman
Rapporteur
Member
Member
Member
Member
Member
Member
Member
Member
KISR
KISR
KISR
KISR
KU
KOC
KOC
KOC
KNPC
KNPC
SCIENTIFIC COMMITTEE
Hamdy M. Shalaby
Abdulhameed Al Hashem
Khalid Habib
Adel Hussein
Waheed Badawi
Afkar Hussain
Emad Al Naser
Eman A. Razzak Al-Shayji
Lakshmipati Cheruvu
Fahed Al-Otaibi
xi
ACKNOWLEDGEMENT
The Organizing Committee was deeply honored by the patronage of H. H. The Crown Prince
and Prime Minister Sheikh Saad Al-Abdullah Al-Salem Al-Sabah, which reflects his keen
interest in science and technology.
The Committee was also grateful for the financial support of the Kuwait Institute for
Scientific Research, Kuwait Foundation for the Advancement of Science, Kuwait National
Petroleum Company, Kuwait Oil Company, Ministry of Electricity and Water, Kuwait
University, Ministry of Oil, the Gulf Cooperation Council, Kuwait Chemical Society,
Organization of Arab Petroleum Exporting Countries, and Petrochemical Industries
Company.
The Committee would also like to extend its deep appreciation for the effort and time put
forth by the distinguished honorary speakers, the members of the International Advisory
Committee, and the Scientific Committee.
We would like to thank our colleagues, the members of the working committees, at the
Kuwait Institute for Scientific Research and the chairmen and cochairmen of the sessions,
who provided unlimited assistance at times when it was really needed. Finally, we feel
deeply indebted to the authors of papers and participants for their valuable contribution to the
success of the conference
Jasem Al-Besharah
Chairman, Organizing Committee
xii
CORROSION MANAGEMENT
V. Ashworth
Global Corrosion
The White House, Victoria Road, Shifnal, England, TF11 8AF
ABSTRACT
The consequences of corrosion are often very costly. Little surprise, therefore, that a substantial
engineering effort is directed towards its prevention and control. By contrast, little consideration
seems to be directed towards making anti-corrosion effort cost-effective. This paper addresses the
problem of ensuring value-for-money corrosion engineering and the possible limitation of unnecessary
corrosion control activities.
Corrosion in itself is not important, but the consequences of corrosion failure may well be. So
the first step in corrosion management is a corrosion risk assessment to evaluate the risk associated
with failure in any item. This is not an evaluation of the risk of failure alone, but of the consequences
should that failure occur.
Given an assessment of risk, a strategy of corrosion management can be constructed. This might
involve lifetime corrosion control for items identified as producing a high risk. A less rigorous, but
monitored, level of protection might be adopted for medium risk items, whilst no action at all may be
considered necessary in the case of low risk items. Thus, resources are distributed according to the
risk.
Once a strategic approach has been defined, the tactics of corrosion management may be
determined. These will include not only the specific corrosion control activity or activities that will be
used in any given case, but also any monitoring and inspection requirements that are necessary. The
object is to maintain corrosion within acceptable limits at minimum cost in all parts of the facility and
throughout the facilitiys life.
Key Words: Risk, probability, monitoring, inspection, corrosion management
INTRODUCTION
The purpose of industry is to make a profit from the production of supplies and artefacts.
In an increasingly competitive world, there is continuing pressure on prices. If the selling
price is under pressure, profitability may only be maintained or increased by cutting costs.
Any factor that serves to increase costs represents a tax on profits.
Corrosion is one certain consequence of using engineering materials. Commonly,
corrosion will be modest, but not always. In the hydrocarbon production and processing
industries and the chemical industry, for example, the exception almost becomes the rule.
Since corrosion brings a cost, it impacts profits.
Plenary Lectures
Frequency (%)
33
18
14
9
9
7
10
Not infrequently, corrosion hits the headlines because some particularly dramatic failure
occurs resulting in the loss of life and property. At Flixborough Works in the UK, a chemical
explosion related to a corrosion failure resulted in 28 fatalities, 36 serious injuries, virtual
destruction of the plant and damage to some 2000 third party properties [6]. In Guadalajara,
in the early 1990's, stray current corrosion of a water pipe produced a failure that caused
erosion-corrosion of an adjacent gasoline line [7]. The leaking gasoline caught fire,
producing an explosion in which tens of local inhabitants were killed.
The accumulated corrosion failures at Dupont and Britoil were potentially costly and the
two accidents were certainly so. That cost is ultimately borne by the community, but in the
short term it falls on the industry concerned.
There is a growing awareness in industry of the costs of corrosion. This engenders a
desire for more effort and expenditure on corrosion prevention and control. Industry finds
willing allies in meeting this goal from the companies that sell anticorrosion materials and
systems. Their products and services are not free.
Ashworth
By contrast, the accountant is rarely moved to make an assessment of the cost of not
having a failure. If a plant and equipment operate without breaking down, everybody is
usually well satisfied. It is rare to question whether the cost of achieving that performance
has been excessive or even worthwhile. Table 3 lists some sources of possible over-spending
in endeavouring to avoid corrosion failures.
Table 3. Costs of Over-Protection
Unnecessarily expensive materials
Overdesign of metal sections
Excessive weight
Excessive inhibitor consumption
Excessive monitoring
Excessive inspection
The items that relate to evident over-engineering in this list may be readily understood.
However, two areas, monitoring and inspection, are worth singling out because they are so
often regarded as a good thing, i.e., they have intrinsic merit. This is far from the case.
Industrial corrosion monitoring is commonly excessive both in terms of the extent of
monitoring and the sophistication of the equipment used. We need to remind ourselves that
corrosion monitoring has never controlled any corrosion. This author believes that corrosion
monitoring should be used almost exclusively in a process control function, the process, in
this case, being corrosion. Thus, a monitoring device should only be used in circumstances
where the output from it can validly be used to adjust some corrosion controlling function,
e.g., inhibitor injection or cathodic protection (CP) output. It follows that probes should not
be installed where such action cannot be taken, nor should they be installed where probes
3
Plenary Lectures
installed elsewhere fulfil essentially the same function. In practice, these rules are observed
more in their breach than in their application. Likewise, for reasons that are well understood,
corrosion probes provide precise information on what is happening on the probe and, often,
comparatively little about what is happening on the pipe or vessel wall. The value of the
probe is that it detects change and prompts review and, possibly, action. Very often simpler
means of detecting change than the use of corrosion-measuring devices will serve the same
function at less cost, e.g., reference electrodes, pH probes, dissolved oxygen meters and
moisture meters in the gas phase. They also have the merit, where relevant, of permitting
continuous readout which allows the identification of the precise 'upset' that produces
corrosion.
Inspection is similarly open to over-engineering. How often is inspection carried out
because we have the opportunity ? It is remarkable that upon shutdown, the internal
inspection of tanks and vessels will often be considered mandatory. Yet pipelines or
pipework that carry the same fluids are not inspected. It has been pointed out [8] that the cost
of inspection is high, often equivalent to 2-6% of the invested capital. That is a significant
tax on profits. What is often overlooked is that inspection can often be potentially dangerous
and may even produce conditions conducive to corrosion, e.g., when sulphuric acid tanks are
opened up for inspection.
If corrosion costs money and corrosion control costs money, how do we target the
optimum approach that strikes the correct balance between ignoring corrosion and seeking to
control it ? The answer lies in
Ashworth
Plenary Lectures
undesirability of the consequences of it occurring. It will be seen below that the probability
component of the risk is rendered quantitative and that the consequence component remains
subjective, but reflects accurately the perceptions and ambitions of the people that own and
run the plant. Subjective it may be, arbitrary it is not.
Methodology
The methodology of conducting a corrosion risk assessment has been discussed in detail
elsewhere [11]. Only a brief outline is presented here.
If we take the example of a corrosion risk assessment in a refinery or chemical plant, it
may be as coarse or as refined as the operator wishes. First, the plant is divided into systems,
e.g., the gas sweetening unit. Second, each system is broken down into items. These usually
comprise individual components, e.g., a vessel, a heat exchanger, a pump or a specifically
identified length of pipework associated with the system. An item may be more widely
defined in a coarse corrosion risk assessment or more closely defined in a fine analysis. In
the latter case, for example, it may involve considering a vessel as a number of discrete items
according to the known variation in fluid composition with height. Equally, it may be
necessary to single out non-stressed relieved welds as separate items and, from an internal
corrosion point of view, each dead leg.
What follows is an outline approach to corrosion risk assessment which has proved to be
successful. Other methods are available that operate somewhat differently [12,13], but aim to
achieve the same objective.
Life Factor
The aim of the corrosion risk assessment is to assign a risk number to each item using a
risk equation similar to equation (1).
There are a variety of ways to deal with the probability element. The experience of the
author's company is that it is best dealt with by assigning a life factor (L) that relates to the
residual corrosion life of the item.
The residual corrosion life is the anticipated time required for corrosion at the predicted
rate, or rates, to lead to failure to perform the required mechanical duty. Given information
on the materials of construction, the exposure environment, and the relevant circumstances
(e.g., temperature, pressure, flow, heat transfer, and stress), the morphology of corrosion can
be predicted with confidence. Where uniform attack is expected, maximum penetration rates
can be calculated using conventional corrosion engineering practices, including public
domain algorithms [14,15,16], in-house database information and, if necessary, modelling. If
localized corrosion is expected (e.g., pitting attack or one of the cracking modes of failure),
probabilistic analyses of failure [17 ] are more useful.
For risk assessment purposes, the estimate of residual life in years is transposed to a
dimensionless L. For example, an anticipated time to failure shorter than the time to the next
shutdown would be assigned an L = 3. Anticipated lives beyond that point would attract L =
2, except where the residual life is put at >10 years in which case L = 1. Of course, this
breakdown is arbitrary and the individual cut-offs, and the relative scoring, can be selected to
match the requirements of the plant owners.
Ashworth
Consequence Factors
The point has been made that the consequence of a corrosion failure are more important
than the failure itself. Thus, the consequences that bear on plant operators' minds include:
Safety,
Production,
Emergency repair,
Operability,
Environment,
Third party interests,
Customer perception, and
Public perception.
Adverse effects on any, or all, of these may often flow from an isolated failure.
The consequence factor (C) is a numerical assessment of the perceived consequences of
a corrosion failure. The number is arrived at using structured group discussions with plant
management, operations personnel, maintenance engineers, loss prevention officers etc. It
elicits a subjective assessment. However, because individuals work towards a consensus in a
group, and the methodology of subsequent analysis is rigorous, the rankings produced
accurately reflect, in a quantitative way, the operating aspirations of the company concerned.
Thus, the C numbers provide the relative importance attached to any consequence. Since the
risk numbers that finally emerge are not absolutes but reflect perceived risk in a relative
manner, the subjectivity of the consequence analysis is not only permissible, but desirable.
The risk assessment becomes plant specific. That is, identical plants operated by different
companies or in different locations will produce different risk assessment results.
There are two elements in establishing the value of C:
Rating (F)
10
9
3
1
1
Plenary Lectures
It should be noted that the company in question is not concerned about contamination of
the product by corrosion or any consequent alienation of the customer. This is a typical
response from a primary producer; quite different numbers would have arisen in an
assessment made in a food or pharmaceutical factory.
The events that lead to a given consequence produce an event rating (P). It is clear that a
number of events which might occur in a process plant, may lead to the same consequence.
The company staff are able to identify and rank these events according to their perceived
undesirability, as shown in Table 5. In this case, the table relates to two plants owned by the
same company in which one uses the product of the other.
Table 5. Typical Event Rating (P)
Consequence
Safety
Outage
Pollution
Quality
Event
Crack in a toxic line or equipment
Pinhole in a melt line
Crack in a flammable line or equipment
Crack in other HP line or equipment
Pinhole in a flammable line or equipment
Pinhole in other HP line or equipment
Other cracks
Pinhole in toxic line or equipment
Other leaks
Falling objects
Plant no. 1 - no standby
Plant no. 2 (HP) - no standby
Plant no. 2 (LP) - no standby
Plant no. 1 - standby
Plant no. 1 - non-critical - no standby
Plant no. 2 - standby
Plant no. 2 - non-critical
Plant no. 1 - non-critical - standby
Marine
Atmospheric
Final product (colour only)
Intermediate product
Rating (P)
10
10
9
7
7
6
5
4
2
1
10
9
7
5
5
4
3
3
10
5
10
5
It is not uncommon when considering safety, for staff to take into account the inventory
of a system. Thus, they will commonly regard a crack in a system or item with a high
inventory and, therefore, a high potential for damage, as more significant than one where the
inventory is small. Different values of P may then arise according to the volume of an
unisolatable part of the system. Any item included in the unisolatable part attracts the P value
for that part.
The values of F and P are combined to yield C:
8
Ashworth
C = Cx =
x=n
x = 1
fn (Fx, Px)
(2)
Where the subscript x refers to each of the consequences, e.g., safety, pollution etc. in turn.
The Risk Equation
The risk equation must reflect the operating company's perception of risk associated
with various forms and rates of failure. The equation, which is derivative of Eq. 1, produces a
numerical assessment of risk (R) and takes the form:
R = fn (L, C)
(3)
The shape of the function linking the life and consequence factors is determined by a
formalized heuristic procedure. The function is modified through a series of computer
iterations with the effect on the value of risk being assessed after each iteration.
Allocation of Risk Classes
The numerical value of risk can be calculated for each item in the plant. The higher the
value of R for any item, the greater the risk and the more attention that must be focused on
the local corrosion situation.
In practice, the spread of numerical risk values amongst all the items within a plant
usually proves to be a discontinuous spectrum. That is, the risk numbers tend to fall into
clusters with distinctive breaks between. This is an inevitable consequence of data like those
recorded in Tables 4 and 5. It permits a convenient reduction of the numeric data into risk
classes (e.g., low, medium and high). Such a sub-division aids communication of the
outcome of the corrosion risk assessment either on a narrative basis or as colour coded P and
ID's. It also assists with establishing a corrosion management programme.
Risk Modification
The fact that, in assessing a new or existing plant, areas of high risk have been identified,
does not mean that the risk must be tolerated. The aim should be to moderate the risk and to
move to a more acceptable condition.
Some methods of corrosion risk assessment [12] do not proceed as far as a risk equation
or a risk number, but rather consider separately the perceived severity of the probability (L in
this case) and the consequence (C). This produces a risk matrix as shown in Table 6.
Table 6. Risk Matrix
Consequence
H
M
L
H
H
HM
M
Probability
M
HM
M
ML
L
M
ML
L
Plenary Lectures
High consequence
Low probability
4
Consequence
Low consequence
Low consequence
High probability
Low probability
2
3
Probability
Using the risk equation approach, the aim is to concentrate resources on areas of high
risk in order to reduce the risk number (i.e., modify the risk). Some care has to be taken here.
It will often be the case that a high risk number will place the specific item in Zone 1 of Table
7. Clearly, for these items, it is important to move towards Zone 3 by means of corrosion
control activities that reduce the risk number.
Somewhat lower risk numbers may fall into either Zone 2 or Zone 4. Indeed, the same
risk number may apply to either a low consequence/high probability situation or a high
consequence/low probability. The former simply represent failures that will be an irritation;
pinholing in a seawater cooling line. The latter are certainly more serious; pinholing in a dry
flammable gas line, for example.
In the case of Zone 2, the high probability means that sufficient data were available to
assess the probability fairly accurately. By contrast, in the case of Zone 4, the reverse is true,
and there may be considerable uncertainty.
If the probability (in our case, L) has been calculated using tried and tested tools, then
identical risk numbers that derive from high probability/low consequence and low
probability/high consequence events are equally reliable. Where the L calculation has used
limited data, an uncertain algorithm or stochastic techniques, that level of reliability is absent.
Thus, in moving from Zone 1 towards Zone 3, it is often better to achieve Zone 2 rather than
Zone 4. Equally, it may be more important to move from Zone 4 than to move from Zone 2.
In general, the consequences of failure are usually not amenable to modification; thus,
risk can only be modified by changing the probability. For that reason, and to introduce
security, risk modification needs to pay attention to moving to situations where the
probability is known or can be determined with some degree of confidence.
10
Ashworth
CORROSION MANAGEMENT
Corrosion risk assessment is not an end in itself. It identifies areas where corrosion may
be safely ignored and where it must be attended to. It even provides the pointer to where
resources will be spent with greatest reward. Thus, it provides the evidence that permits the
construction of a cost-effective corrosion management programme. The objectives of a
programme relate to the whole life of a facility and are to
Medium
Low
11
Plenary Lectures
It will be recalled that corrosion risk assessment is carried out by dividing the plant into
systems and items. Ultimately, the output relates to individual items. It is possible for an
item within a system to have a high risk classification whilst other items in the same system
belong to a lower risk class. The decision must then be made whether to apply corrosion
control to the system in order to preserve the item, or to ensure corrosion prevention for the
item (say, by the use of more corrosion-resistant material) and avoid dealing with the system.
The application of the broad strategy does allow, and requires, some flexibility in the tactics
adopted.
Tactical Considerations
The complete elimination of the chance of corrosion failure, i.e., corrosion prevention, in
a high risk area is rarely possible in an existing plant. Invariably, it would require a
significant engineering change, for example, replacement of existing materials by corrosionresistant alloys or modification of the process (e.g., addition of gas dehydration). Even with
new plants, such proposals might raise major design and engineering problems, not to
mention cost.
It is much more likely that active corrosion control will be adopted with the objective of
extending the time to failure of an item beyond the planned life of the plant, or up to some
planned maintenance shutdown. The adoption of this tactic requires that:
the performance targets for the corrosion control are defined, and
procedures are put in place to ensure the targets are met.
The performance target may be set in terms of an allowable rate of metal penetration.
This approach will most commonly be adopted when uniform corrosion is anticipated.
Alternatively, limits may be set on some parameter that is an indication of fluid corrosivity,
e.g., electrode potential in anodic and cathodic protection systems, dissolved oxygen in
oilfield water injection or boiler feedwater, pH, temperature, or dewpoint. Irrespective of
which approach is adopted, it will be necessary to obtain on-line information to make
adjustments as required. Thus, corrosion monitoring is necessary, and it then forms an
essential segment of the corrosion management plan. Table 9 lists some monitoring
techniques and indicates how they may be used in corrosion management.
Table 9. Corrosion Monitoring in Corrosion Management
Corrosion Control Strategy
Examples of Adjustments
and Activities Based on
Data Monitoring
Inhibition of crude oil On-line
probes
(e.g., Adjust inhibitor dosage,
pipelines
coupons, electrical resistance change inhibitor type,
probes)
discontinue inhibition
De-oxygenation of boiler O2 probes
Adjust oxygen scavenger,
feed-water
check pump seals, etc.
Impressed current CP
Potential
Adjust system output
Anodic
protection
of Potential
Adjust system output
sulphuric acid plant
12
Monitoring Technique
Ashworth
On-line probes,
moisture detection
Temporary inhibition,
overhaul dehydrator
The key to effective corrosion management is information since it is on the basis of that
information that on-going adjustments to corrosion control are made. Information is valid
data. Thus, to make effective corrosion management decisions on a day-to-day basis, the
monitoring data must be valid. This is not simply a requirement for the probes to be
operating correctly. It requires that they be placed in the most appropriate places, i.e., at
those points where the corrosion controlling activity might be expected to work, but where it
might equally be expected to be least effective, e.g., remote from the inhibitor injection point.
In many cases specially designed traps are introduced into a plant so that corrosion probes
may be inserted. These often produce their own microenvironment, atypical of the plant
itself, and with little hope of effective entry for an inhibitor. Data from a probe in such a
location are unlikely to be relevant to corrosion management elsewhere in the system. Invalid
data leads to ineffective corrosion management.
Keeping Track
In any facility the means of corrosion management will vary from place to place. In one
location a corrosion resistant alloy may be used; in another, CP allied to coating may be
employed, whilst elsewhere no action may be taken because the consequences of any failure
are regarded as unimportant. In short, no corrosion management action is taken that does not
contribute positively to meeting the objective of containing risk whilst maintaining the level
of action at the minimum necessary.
It is important to ensure that the targets are being met. Overshooting the target will
involve excessive corrosion control costs, whilst undershooting the target may lead to a
situation that cannot economically be recovered. Corrosion monitoring is not appropriate for
the purpose since it rarely provides evidence of the metal loss from a pipe or vessel wall.
That is, aggregating the output from probes over time does not give any indication of the loss
of a section. The value of corrosion probes is that we rapidly develop experience so that we
can be reasonably sure that when the probes read a given value, we are on target, and that a
change in reading requires consideration of an adjustment to the corrosion controlling
activity. Reference electrodes, pH probes, moisture meters etc. often fulfil the same function.
Thus, corrosion probes and the like, do not provide quantitative performance assessment.
That can only come from inspection and nondestructive testing (NDT). These activities are
part of corrosion management since they provide reassurance, identify wasteful corrosion
control activity, and permit reassessment of the corrosion management programme. The
same critical approach that was adopted in setting up the corrosion control strategy must be
applied to the inspection strategy. That is, the resources must be applied according to the risk.
If we have attempted to modify the risk by instituting some corrosion control activity, we
should be tracking the success, or excess, of the activity in our inspection programme. Thus,
inspection is not based on convenience, inspecting because an item is accessible (at
shutdowns, for example). It should be based on the premise that if the consequences of
failure are to be avoided and the cost of control is to be minimized, inspection is necessary.
There must, therefore, be a clear connection between the risk assessment output, the corrosion
management strategy, the tactics of corrosion management and the inspection programme.
13
Plenary Lectures
The key point approach to NDT is particularly effective. Here a limited number of
points, in areas where validation is required, that are regarded as typical and extreme, are
identified for NDT inspection at regular intervals. This provides, on a temporal basis, a
readout of the progress of corrosion which will validate, or otherwise, the targeting achieved
by, say, inhibitor injection.
Similarly, during internal inspection, the risk assessment will have identified particular
areas of concern, e.g., tube/tube sheet assemblies, tube baffles, and non-stress relieved welds,
which must become the focus of activity. Again, this will confirm whether the corrosion
control is adequate or perhaps is insufficient or excessive.
The data that are produced from the inspection activities must be valid and limited in
volume so as not to deter analysis or hide anomalies. Thus, it is important to restrict key
points and inspections to critical positions and to limit the frequency of inspection and survey
work. The time to the next inspection or survey should be indicated by the outcome of the
current work. That is, a lifetime fixed interval programme will usually prove wasteful;
inspection and survey should be carried out on an as-needed basis. A valuable template
giving an approach to the re-classification of in-service inspection is to be published in 1996
[18] and has been reviewed in reference [12].
Review
From time to time a corrosion management programme should be reviewed at both the
strategic and tactical level. In human affairs, things change. The management of a facility
will always be alive to current market trends, competitors activities, interest rate movements
and so on. Inevitably, it may be necessary to revise the management objectives from time to
time. Since the corrosion management programme was constructed to meet the objectives of
an earlier plant management plan, it will be necessary to review the programme and possibly
to alter it. Likewise, the pace of technological change is rapid compared to the anticipated
lifetime of most facilities. Thus, newer, more effective, cheaper means of achieving the same
ends may emerge, and indeed, it may be possible to adopt them in place of existing tactics
within the corrosion management programme. Thus, the programme is not a fixed blueprint,
but a means to an end that must be reviewed and revised to meet the current management
objective.
One objection that is raised to corrosion management planning comes from the corrosion
engineers themselves. They draw attention to the fact that by fixing permissible rates of
metal loss, the lifetime of the facility is effectively determined. Further, that management
will often, at a later stage, decide to extend the required operating life. There is then a
mismatch. The argument seems to be that corrosion management planning should ignore the
present requirements and anticipate the future requirements of the management. This is an
extremely wasteful approach. Certainly there is a possibility that a mismatch will occur and
will need to be overcome. That will be achieved at some cost. That cost must be attributed to
the decision to go for life extension and is, therefore, a natural consequence of that extension.
It needs to be included in the cost benefit analysis of extension, not hidden in lifetime
overspending in anticipation that life extension might be required. It may not be.
ILLUSTRATIONS
14
Ashworth
Two recent examples illustrate how corrosion risk assessment provided important results
for the clients. In the first instance, the assessment of a petrochemical complex in the Middle
East found the plant to be extremely well engineered from the corrosion standpoint. It was
constructed predominantly in carbon steel, with excursions into more exotic metallurgy only
where the process conditions demanded it. However, the assessment highlighted, somewhat
to the client's surprise, the cooling water system as a high risk area.
By using a closed system with secondary cooling by seawater and specifying high
quality primary water with corrosion inhibitor injection, the designers had judged that it was
possible to construct the majority of the cooling system in carbon steel. Certain that the
primary heat exchangers were, however, constructed in a stainless steel due to the
aggressivity of the process fluid, the corrosion risk assessment identified modes whereby the
quality of the cooling water could be adversely affected (e.g., by leakage of seawater at
secondary plate exchangers). Failure to maintain cooling water within specification would
very rapidly lead to stress corrosion cracking of one of ten critical stainless steel process
exchangers, failure of any one of which would halt production.
In view of this, Global Corrosion put forward recommendations for modest on-line
monitoring of cooling water quality. Tied to this was the setting up of a formal action plan to
be followed in the event a sudden deterioration in water quality should be detected. The
client accepted and implemented these recommendations but, unfortunately, not before one
failure of the type predicted occurred.
The second example derives from an installation, also in the Middle East. The corrosion
risk assessment concluded that the absence of CP on water storage tanks, together with the
prevailing soil conditions, would result in high tank bottom corrosion rates. Since an
adequate supply of water was essential to maintain production, the assessment concluded that
the prospective failure of the tanks constituted a high risk and it was strongly recommended
that CP be installed.
In the event the client was reluctant to accept and act upon the outcome of the report.
Just under a year later the raw water tank perforated due to soil-side corrosion. The resulting
loss of water caused a two week interruption in production, prompted a belated decision to
install CP and engendered in the client a heightened appreciation of the benefits of corrosion
risk assessment and the need for effective corrosion management.
CONCLUSIONS
Corrosion cannot be ignored for it will not go away. However, there is little merit in
controlling corrosion simply because it occurs, and none in ignoring it completely. The
consequences of corrosion must always be considered. If the consequence of corrosion can
be lived with, it is entirely proper to take no action to control it. If the consequences are
unacceptable, steps must be taken to manage it throughout the facilitys life at a level that is
acceptable. To manage is not simply to control.
Good corrosion management aims to maintain, at a minimum life cycle cost, the levels of
corrosion within predetermined acceptable limits. This requires that, where appropriate,
corrosion control measures be introduced and their effectiveness ensured by judicious, and
not excessive, corrosion monitoring and inspection. Good corrosion management serves to
support the general management plan for a facility. Since the latter changes as market
15
Plenary Lectures
conditions, for example, change, the corrosion management plan must be responsive to that
change. The perceptions of the consequences and risk of a given corrosion failure may
change as the management plan changes. Equally, some aspects of the corrosion
management strategy may become irrelevant. Changes in the corrosion management plan
must, inevitably, follow.
REFERENCES
1. T.P. Hoar (Chairman), Report of the Committee on Corrosion and Protection, HMSO,
London, 1971
2. B.W. Cherry and B.S. Skerry, Corrosion in Australia - the Report of the Australian
National Centre for Corrosion Prevention and Control Feasibility Study, Monash
University, 1983.
3. L.H. Bennett, National Bureau of Standards Special Publication 511.1, NBS,
Washington, 1978.
4. A.J. Sedriks, Corrosion of Stainless Steels, Wiley, 1979, p. 7.
5. Kermani, An Overview of Wet H2S Attack: Types, Causes and Problems, in Papers of
the Conference on Wet H2S Attack on Steels, Institute of Mechanical Engineers,
London, 1996.
6. F. Lees, Loss Prevention in the Process Industries, Vol 2, p863, Butterworth (1989)
7. J.M. Malo, V. Salinas and J. Uruchurtu, Materials Performance 33, 8, 1994, p. 63.
8. C. Edeleanu and J.G. Hines, Materials Performance 29, 12, 1990, p. 68.
9. P. Slovic, Science 236, 17 April 1987, p. 280.
10. M.E. Giuntini, Proceedings of Fourth Space Logistics Symposium, Florida, November
1992.
11. V. Ashworth and W.R. Jacob, Proc. Corrosion 32, Australasian Corrosion
Association, 1992.
12. B. Spalford, Carbon steel equipment in wet H2S service, Papers of Conference on Wet
H2S Attack on Steels, Institution of Mechanical Engineers, London, 1996.
13. Private communication, Shell-Expro, UK
14. C. de Waard, V. Lutz and D.E. Milliams, Corrosion 47, 1991, 976.
15. F.A. Posey and A.A. Palko, Corrosion 35, 38 (1979)
16. J.W. Oldfield, G.L. Swales and B. Todd, Proc. 2nd BSE/NACE Corrosion
Conference, Bahrain, 1981.
17. M. Akashi, Proc. Conference of Life Prediction of Corrodable Structures, NACE,
1991.
18. EEMUA publication 179, A Working Guide for Carbon Steel Equipment in Wet H2S
Service (to be published in 1996)
16
ABSTRACT
As our industrial and infrastructural systems (refineries, power plants, pipelines, etc.) age,
considerable economic incentive develops to avoid unscheduled outages and to extend operation
beyond the design lifetime. The avoidance of unscheduled outages is of particular interest, because
the failure of even a minor component can result in the complete shutdown of a facility. For example,
the unscheduled shutdown of a 1000 Mwe nuclear power plant may cost the operator between US $1
million and US $3 million per day, depending upon the cost of replacement power and other factors.
However, if component failures could be accurately predicted, maintenance could be performed
during scheduled outages, the cost of which has already been built into the price of the product. With
regard to life extension, the successful extension of operation beyond the design life translates into
enhanced profits and the avoidance of costly licensing and environmental impact assessments
associated with the development and construction of a new facility. In this case, as well, the key to
successful operation is the ability to avoid downtime, and hence, to maintain production. Eventually,
the frequency and severity of unscheduled outages will render operation uneconomic, and at that
point, replacement of the facility is necessary. In order to develop effective inspection and
maintenance scheduling and life extension technologies, it is first necessary to predict the evolution of
damage into the future as a function of various system variables. The only effective prediction
technologies are those based on determinism, in which the system behavior is described in terms of
natural laws. In this paper, the deterministic prediction of damage, via damage function analysis
(DFA), which provides a robust technology for estimating the damage function at future times, is
described. The application of DFA to the prediction of pitting damage is illustrated by reference to
pitting damage in condensing heat exchangers.
Key Words: Corrosion damage, determinism, prediction, pitting corrosion.
INTRODUCTION
Corrosion is a major cause of component failure, and hence, in the occurrence of
unscheduled downtime, in complex industrial systems. In particular, the various forms of
localized corrosion, including pitting corrosion, crevice corrosion, stress corrosion cracking
(SCC), and corrosion fatigue (to name the common forms) are particularly deleterious
because they frequently occur without any outward sign of damage, and because they often
result in sudden and catastrophic failures. Thus, the development of effective corrosion
damage prediction technologies is essential for the successful avoidance of unscheduled
downtime and for the successful implementation of life extension strategies.
17
Plenary Lectures
Macdonald
Duty
Cycle
Chloride
Concentration
Condensate
Temperature
Flue Gas
Composition
Condensate Chemistry
Model
pH.[Cl-]*
Mixed Potential
Model
Ecorr.pH. [Cl-]
Pit Nucleation
Model
N(t).Ecorr.pH. [Cl-]
Pit Growth
Model
N(tobs) vs. n(u)
Damage Function
Model
Service Life
Figure 1.
Wall Thickness
Specifier
Failure
Probability
Below I describe the various modules in this algorithm; however, due to the limited
space available, I outline only the principles of these modules.
19
Plenary Lectures
Cooling Air
Exhaust
Heat Exchanger
Simulator
Flue Gas
Flow
Zone 1 Zone 2
Zone 3
Zone 4
T = 353-326oK
Zone 5
T = 308-326oK
Cooling Air
Figure 2a. Schematic diagram of a typical heat exchanger in a gas-fired furnace [4]
20
Macdonald
21
Plenary Lectures
(1)
where iR/O,j is the partial current density due to the j-th redox couple in the system, and icorr
is the corrosion current density of the substrate. The currents are written as functions of the
potential E to emphasize the fact that the partial currents depend on the potential drop across
the metal/solution interface. Indeed, the solution to Eq. 1 provides the quantity that we seek
(i.e., the corrosion potential). Note that in deriving Eq. 1, the surface of the alloy is assumed
to be equally accessible to all reactions in the system.
Macdonald
breakdown that are in good agreement with experimental data [8-11]. We derived these
distribution functions from our point defect model for the growth and breakdown of passive
films, by assuming that breakdown occurs when a critical concentration of cation vacancies
accumulates locally at the metal/passive film interface, such that decohesion occurs between
the barrier layer and the metal substrate. Subsequently, localized dissolution and/or
mechanical instability leads to rupture of the film [8]. We further assumed that the
breakdown sites are normally distributed with respect to the diffusivity of cation vacancies
within the film [9-11]. The full derivation of these distribution functions can be found in the
literature [8-11].
From the point defect model [8], the breakdown voltage and the induction time for a
single pit nucleation site on the surface are given by
Vc =
4.606RT
J
2.303RT
log o m / 2
log(a x )
J u
F
F
and
(2)
FV
tind = exp
1 +
2RT
(3)
o
J = a D
and
N
a = K v
1+
exp Gs /RT
o
(5)
1
2 D
exp (D D) / 2 D
2
(6)
where D is the mean diffusivity and D is the standard deviation, the point defect model
yields the following expressions for the distributions in the breakdown voltage and induction
time [9-11]:
2
2
D
dN
=
e(D D) / 2 D
(7)
2 D
dVc
and
23
Plenary Lectures
dN u / 2 (D D )2 / 2 D2
e V
=
/2
e
2
dt ind 2 D a
a x (t ind )
where
= F/2RT
(8)
(9)
Eqs. 7 and 8 contain four important system parameters: D and D which describe the
transport properties of cation vacancies in the passive film, and and which appear in the
expression for the dependence of the potential drop across the film/solution interface on
applied voltage and pH
f/s = V + pH + f/so
(10)
Gas
h
a0
Metal
24
Macdonald
Fe + n 4 H 2 O Fe
( OH ) (n 2 n
Cr + n 5 H 2 O Cr ( OH
) (n
Ni + n 6 H 2 O Ni ( OH
) (n 2 n
H2O H
+ OH
3n
+ n4H
+ 2e
+ n5H
+ 3e
+ n6H
+ 2e
Figure 4. Schematic diagram of a pit on the surface of the condensing heat exchanger
The principle of the transmission line approach is shown in Fig. 5, which yields the
following equations for the distributions in the electrostatic potential (s ) and the current in
the external environment
d 2s 1 d s
=0
2 +
dr
r dr hZs s
(11)
d 2 I 1 dI
I= 0
2
dr
r dr hZs
(12)
e( s s )/b a e( s s )/b c
i =
+i
1 1 -( s se )/b a 1 s se /b c p ( s )
+ e
e
il,r
i o il,f
e
C
N
(13)
where the first term on the right-hand side is the generalized Butler-Volmer equation for the
oxygen electrode reduction
2H 2 O O 2 + 4H+ + 4e
(14)
and the second is the polarization current of the substrate, both of which are functions of the
potential difference across the interface. The parameters se , io, il,f, il,r, ba, and bc in Eq. 13 are
the negative of the equilibrium potential for Reaction 14, io is the exchange current density, il,f
and il,r are the limiting current densities for Reaction 14 in the forward and reverse directions,
respectively, and ba and bc are the corresponding Tafel constants. Note that the signs of the
exponents in the first term in Eq. 13 are opposite to those normally defined because we have
written the current in terms of the electrostatic potential in the solution with respect to the
metal. We used the finite difference method to solve Eqs. 11 and 12 for s (r) and i c(r) ,
respectively.
25
Plenary Lectures
The distribution of the electrostatic potential within the pit is obtained by solving
Laplace's equation, assuming that the environment within the pit confine is electrically
neutral,
= 0
2
(15)
The solution to Laplace's equation (Eq. 15) yields the following expression, assuming
that the potential variation in the radial direction is negligible compared to that in the
longitudinal direction:
Z
Electrolyte film
r+dr
Crevice
Metal
Figure b
(a) Element of electrolyte film on the metal surface.
I
Rdr
I-dI
Z(r)/dr
m
(b) Element of transmission line for calculating current and potential
distributions radially from the crevice mouth.
Figure 5. Transmission line model for thin electrolyte film on the metal surface
s (z) = ( s0 sL ) + s0
z
L
(16)
where sL is the electrochemical potential at the pit tip, L is the pit depth, and z is a negative
quantity. We also apply the Butler-Volmer equation to the electrodissolution reaction
occurring at the pit bottom to yield the electrochemical potential at the pit tip as [14]
i 00 A
I0
sL = s00 + ba1n
(17)
where s00 is the (negative of the) standard electrochemical potential for the dissolution of the
metal, i 00 is the standard exchange current density, ba is the anodic Tafel constant for metal
dissolution, and At is the effective active surface at the pit tip. The model outlined above is a
variant of the Coupled Environment Fracture Model (CEFM) that we developed some time
ago [15] for describing crack growth in stainless steel piping in nuclear power reactor heat
26
Macdonald
transport circuits. Thus, following our previous work [15], Eqs. 11, 12, 16, and 17 are solved
for the unknowns s (r) , i c(r) , and Io, such that charge conservation, expressed as
I0 + i C dS= 0
N
(18)
is obeyed, where I0 is the (positive) current exiting the pit mouth, and dS is an increment of
the external surface (dS = 2 rdr ). Because the cathodic current due to oxygen reduction
predominates on the external surface, the second term on the left side of Eq. 18 is negative.
Once I0 is known, then the pit growth rate is calculated using Faraday's law:
dL
M I0
=
dt 2 m Z FA
(19)
where m is the density of the metal (g/cm3), M is the composition-averaged atomic weight
of the alloy, and Z is the composition-weighted oxidation state of the metal dissolving at the
pit tip. Finally, the pit length is calculated as a function of time using the recursive formula:
L(t) = L(t 1) +
dL
t
dt
(20)
where L(t-1) is the depth of the pit calculated from the previous time (t-1), and t is the
increment in time.
The Damage Function Module (DFM)
By combining Eqs. 8 and 20 for a fixed density of potential breakdown sites (No,
number/cm2), it is possible to estimate the pitting damage function. Thus, if one observes the
system at time tobs, then the number of pits that nucleate over the time increment t at tind is
N , as determined from Eq. 8. However, these pits will have grown to a depth L(t), as given
by Eq. 20, at the time the system is examined. By moving the increment t from t = to
t = t obs , the damage function is then generated in the form of the number of pits versus the
depth of the pits. If this procedure is repeated for different observation times, a family of
damage functions is generated that extends to greater depths with increasing tobs.
By specifying the surface area of interest, it is possible to define the service life as the
time taken for one or more pit to grow to the critical length, which in this case corresponds to
the wall thickness of the condensing heat exchanger. The number of pits with lengths
exceeding the critical dimension is simply calculated as
L max
N L L crit = S N(L) L
(21)
L crit
where N(L) is the density of pits per unit surface area and per unit increment in pit length
(number/cm3) in the damage function, S is the surface area of interest (cm2), L is the pit
27
Plenary Lectures
length, L is the increment of the pit length in the damage function, and Lcrit is the critical
dimension. The service life is simply the time at which N L L crit = 1.
DISCUSSION
The procedure outlined above for estimating damage functions for localized corrosion is
currently being developed to explore the impact of corrosion on condensing heat exchangers
in domestic and industrial gas-fired furnaces. The practical problem lies in selecting the most
cost-effective alloys for the condensing stages of heat exchangers, because of the highly
competitive nature of the furnace manufacturing business. Consequently, little room exists
for over-designing furnaces by employing highly-alloyed, costly materials to fabricate the
condensing sections. Therefore, selection of materials with adequate pitting resistance, and of
acceptable cost, is of prime concern to furnace manufacturers and users alike. It is evident,
then, that the design and materials specifications for condensing heat exchangers would
greatly benefit from the development of a deterministic method for predicting localized
corrosion damage functions. This, in turn, could reduce the cost of the alloy by decreasing
the required database, through the availability of deterministic relationships between the
damage function and important environmental variables (including pH, [Cl-], and gas
composition).
In this study, I present predictions of the model in comparison with experimental damage
functions measured on Type 304L stainless steel by G. Stickford, B. Hindin, and A.K.
Agrawal of The Battelle Columbus Laboratories. For the experimental data, the damage
functions are measured on condensing heat exchanger tubes after a given number of cycles, at
the hot end (temperature ranging from 326o to 353oK) and at the cold end (temperature
ranging from 308o to 326oK). Each cycle consists of 240 second with the burner on and 480
sesond with burner off, which represent the dry and wet conditions, respectively. It was
shown in a previous study [4], that no significant difference exists in the damage functions
between the hot end and the cold end; the damage functions are, therefore, plotted without
distinction between the hot ends and cold ends. Based on this experimental finding, the
model is constrained to the case where the surface is covered at all times by a condensing
liquid phase (wet condition). However, I choose the appropriate temperature at the hot end to
calculate the damage functions in order to avoid underestimating the damage.
The experimental data reported by Battelle were measured at three levels of chloride
concentration (3, 26, and 225 ppm) on a number of different candidate alloys. I present in
this study only the damage functions for Type 304L stainless steel, as shown in Figs. 6, 7, and
8, as a function of chloride concentration. Not surprisingly, fewer pits were observed at the
lower chloride concentration (3 ppm, Fig. 6). At higher chloride levels (26 and 225 ppm), the
number of pits increased substantially (Figs. 7 and 8) and led to perforation of the wall in
shorter time, thus reducing the service life. However, the experimental data show some
inconsistencies, which are due to the fact that different tubes were used to determine the
damage functions in each case. The chemical composition, the metallurgical history, and the
surface state may vary from tube to tube.
Because, the kinetics of the cathodic oxygen reaction on Alloy Al29-4C are considered
to be essentially identical to those on Type 304L stainless steel, the parameters for Al29-4C
were chosen for calculating the corrosion potential used in estimating the damage functions
28
Macdonald
(Table 1). Calculated damage functions are presented in Figs. 9 through 12 for chloride
levels of 3, 10, 26 and 225 ppm, respectively. The calculations clearly indicate the
progressive nature of the nucleation and growth of pits on the alloy surface. It is predicted
that at lower chloride concentrations (3 ppm), fewer pits exist on the surface of the steel,
while at higher chloride concentrations (26 to 225 ppm), the number of pits increases
substantially, leading to the majority of the pits perforating the wall thickness in a short
period of time.
The predicted service life is presented as a function of chloride concentration in Fig. 13,
in comparison with the experimental data. The calculations indicate that the service life of a
condensing heat exchanger is highly sensitive to the chloride level in the condensate,
especially at the lower chloride concentration (3 ppm). The principal effect of increasing
chloride is to accelerate pit nucleation, so that, in the limits of very high chloride
concentration, (~>100 ppm) in the condensate, the failure time is dominated by pit growth.
Because the pit growth rate is dominated by the conductivity of the external environment (i.e.,
the condensate film), for any given pH and oxygen concentration, and because the
conductivity is dominated by non-chloride species, the failure time becomes constant at
sufficiently high chloride levels. This corresponds to the situation where the entire service
life is determined by the time required for the pits that nucleate on initial exposure of the
alloy to condensate and grow through the condenser wall. Noting that the service life for the
case shown in Fig. 13 is calculated to decrease from 1.55 x 108 s (4.92 years) for a chloride
concentration of 3 ppm to 2.34 x 107 s (0.74 year) for a chloride concentration of 225 ppm, it
is evident that the time required for an active pit to perforate the wall is about three-quarters
of a year, corresponding to an average pit growth rate of 0.7 mm/year. Clearly, then, the
increase in the service life on lowering the chloride concentration is due almost entirely to an
increase in the initiation time, and it would seem that substantial service lives for this alloy
can only be obtained if nucleation becomes the dominant phase in the development of
damage. Finally, due to the fact that different tubes are used in determining the damage
functions, the experimental data are rather scattered. In recognition of this observation,
relatively good agreement is claimed between the experimental data and the theoretical
prediction.
Table 1. Values for Parameters Used in Calculating Damage Functions
Parameter
G AO 1
f/sO
O
Gs
Value
3
30
-60
-0.375
20
0
1 x 106
0.25
-0.001
1 x 1016
Units
cm3/gm cation
kJ/mol
V
kJ/mol
s
V/cm
V
No/cm2
29
Plenary Lectures
Jm
D
0.12 x 107
vacancy 1.0 x 10-18
vacancy
Vacancies/cm2.s
cm2/s
0.5 D
cm2/s
The influence of the oxygen partial pressure on the development of damage functions has
been calculated, and is shown in Fig. 14. The calculations indicate that oxygen has a great
impact on the service life of heat exchangers. This is because oxygen, in the condensed
liquid phase on the external surface, consumes the positive current associated with the pit tip
dissolution process, thereby driving the growth of the pit. By decreasing the partial pressure
of oxygen from 10-4 atm to 10-8 atm, the service life of a heat exchanger having the
characteristics assumed in this work could be extended from 3.02 x 107 s (1 year) to 1.05 x
109 s (approximately 30 years).
Figure 6. Measured pitting damage functions for Type 304L stainless steel heat
exchanger tubes under condensing conditions: [Cl-] = 3 ppm,
temperature ranging from 308o to 353oK, pit counting interval = 2.54 x
10-3 cm. a) Tobs = 4.32 x 106 s; b) Tobs = 8.63 x 106 s; c) Tobs = 1.73 x
107 s; tube thickness = 5.34 x 10-2 cm, as indicated by the dashed line
Figure 7. Measured pitting damage functions for Type 304L stainless steel heat
exchanger tubes under condensing conditions: [Cl-] = 26 ppm,
temperature ranging from 308o to 353oK, pit counting interval = 2.54 x
10-3 cm. a) Tobs = 4.32 x 106 s; b) Tobs = 8.63 x 106 s; c) Tobs = 1.73 x
107 s; d) Tobs = 3.46 x 107 s; e) Tobs = 5.18 x 107 s; tube thickness = 5.34
x 102 cm, as indicated by the dashed line
Figure 8. Measured pitting damage functions for Type 304L stainless steel heat
exchanger tubes under condensing conditions: [Cl-] = 225 ppm,
30
Macdonald
Figure 9. Calculated pitting damage functions for Type 304L stainless steel heat
exchanger tubes under condensing conditions: [Cl-] = 3 ppm,
temperature = 350oK, PCO = 2.60 x 10-5 atm, PCO2 = 6.80 x 10-2 atm,
PSO2 = 9.37 x 10-9 atm, PSO3 = 2.00 x 10-9 atm, PH2S = 1.20 x 104 atm,
PNO = 1.74 x 10-8 atm, PNO2 = 2.67 x 10-8 atm, PO2 = 1.00 x 10-4 atm, pit
radius = 1.00 x 10-4 cm, initial pit depth = 1.00 x 10-3 cm, pit counting
interval = 2.54 x 10-3 cm, a) Tobs = 6.30 x 107 s; b) Tobs = 1.58 x 108 s;
tube thickness = 5.34 x 10-2 cm, as indicated by the dashed line
Figure 10. Calculated pitting damage functions for Type 304L stainless steel heat
exchanger tubes under condensing conditions: [Cl-] = 10 ppm,
temperature = 350oK, PCO = 2.60 x 10-5 atm, PCO2 = 6.80 x 10-2 atm,
PSO2 = 9.37 x 10-9 atm, PSO3 = 2.00 x 10-9 atm, PH2S = 1.20 x 10-4 atm,
PNO = 1.74 x 10-8 atm, PNO2 = 2.67 x 10-8 atm, PO2 = 1.00 x 10-4 atm,
pit radius = 1.00 x 10-4 cm, initial pit depth = 1.00 x 10-3 cm, pit
counting interval = 2.54 x 10-3 cm, a) Tobs = 3.15 x 107 s; b) Tobs =
4.10 x 107 s; c) Tobs = 4.41 x 107 s d) Tobs = 5.36 x 107 s e) Tobs = 6.30
x 107 s; tube thickness = 5.34 x 10-2 cm, as indicated by the dashed
line
31
Plenary Lectures
Figure 11. Calculated pitting damage functions for Type 304L stainless steel heat
exchanger tubes under condensing conditions: [Cl-] = 26 ppm,
temperature = 350oK, PCO = 2.60 x 10-5 atm, PCO2 = 6.80 x 10-2 atm,
PSO2 = 9.37 x 10-9 atm, PSO3 = 2.00 x 10-9 atm, PH2S = 1.20 x 10-4 atm,
PNO = 1.74 x 10-8 atm, PNO2 = 2.67 x 10-8 atm, PO2 = 1.00 x 10-4 atm,
pit radius = 1.00 x 10-4 cm, initial pit depth = 1.00 x 10-3 cm, pit
counting interval = 2.54 x 10-3 cm, a) Tobs = 4.32 x 106 s; b) Tobs =
8.63 x 106 s; c) Tobs = 1.73 x 107 s d) Tobs = 2.52 x 107 s e) Tobs = 2.84
x 107 s; f) Tobs = 2.99 x 107 s; g) Tobs = 3.15 x 107 s; h) Tobs = 3.46 x
107 s; i) Tobs = 5.19 x 107 s; tube thickness = 5.34 x 10-2 cm, as
indicated by the dashed line
Figure 12. Calculated pitting damage functions for Type 304L stainless steel heat
exchanger tubes under condensing conditions: [Cl-] = 225 ppm,
temperature = 350oK, PCO = 2.60 x 10-5 atm, PCO2 = 6.80 x 10-2 atm,
32
Macdonald
PSO2 = 9.37 x 10-9 atm, PSO3 = 2.00 x 10-9 atm, PH2S = 1.20 x 10-4 atm,
PNO = 1.74 x 10-8 atm, PNO2 = 2.67 x 10-8 atm, PO2 = 1.00 x 10-4 atm,
pit radius = 1.00 x 10-4 cm, initial pit depth = 1.00 x 10-3 cm, pit
counting interval = 2.54 x 10-3 cm, a) Tobs = 1.58 x 107 s; b) Tobs =
2.21 x 107 s; c) Tobs = 2.52 x 107 s d) Tobs = 3.15 x 107 s; tube
thickness = 5.34 x 10-2 cm, as indicated by the dashed line
Figure 13. The measured and calculated service life for Type 304L stainless
steel heat exchanger tubes as a function of the chloride
concentration (parameters are identical to that for Figs. 6-8 for
experimental data and Figs. 9-12 for calculation)
33
Plenary Lectures
Figure 14.
The calculated service life for Type 304L stainless steel heat
exchanger tubes as a function of the partial pressure of oxygen
(temperature = 350oK, PCO = 2.60 x 10-5 atm, PCO2 = 6.80 x 10-2 atm,
PSO2 = 9.37 x 10-9 atm, PSO3 = 2.00 x 10-9 atm, PH2S = 1.20 x 10-4 atm,
PNO = 1.74 x 10-8 atm, PNO2 = 2.67 x 10-8 atm)
34
Macdonald
35
ABSTRACT
Laboratory tests are a convenient means for simulating service environments for the purpose of
evaluating both corrosiveness of the environment and material performance. Such tests can provide
substantial information upon which engineering decisions can be made. These decisions generally will
be made with greater confidence and a more efficient materials design. Measurements can be made
under more controlled and reproducible conditions than are possible in field or plant situations. The
consequences of process changes can be evaluated in advance of the actual situation. However, when
conducting tests in simulated service environments, it is most important that the experimental methods
be designed with the specific intent to provide meaningful, representative, correlative results. This
presentation will review the various aspects that must be included when designing, conducting, and
interpreting corrosion tests in simulated service environments. Several case studies will also be
presented that involve petroleum applications, including the selection of corrosion-resistant alloys in
sour petroleum production, inhibition of multiphase flow lines, assessment of crude oil corrosiveness,
and corrosion under insulation.
Key Words:
INTRODUCTION
There are many types of laboratory corrosion tests utilized for various purposes. These
tests can range from simple glassware immersion tests involving freely corroding, nonstressed coupons to highly sophisticated exposure tests involving dynamic replenishment,
heat and/or mass transfer and high pressures maintained only through autoclave, flow loop or
pilot plant operations. Furthermore, they may also involve ancillary techniques which
include a variety of DC or AC electrochemical methods and mechanical loading
configurations. To extend the predictive capabilities of the tests results, modeling techniques
and statistical experimental design programs can be employed that allow for identification or
verification of mechanisms or for establishment of linkages between the results of the
laboratory test and the intended service application while minimizing the number of tests
required.
LABORATORY TESTING: A BASIC AND IMPORTANT TOOL
In many areas of technical activity, emphasis is now being placed on reducing the overall
time, funding and effort allocated for testing, research, development and engineering. In
37
Plenary Lectures
some cases, corrosion testing appears as only an afterthought. At the same time, there are
pressures to provide systems with higher reliability and reduced operating costs. In simpler
words, these engineering concepts can be referred to in four basic terms: Better, Cheaper,
Faster, Safer [1]. One of the most important aspects that must be realized is that these are not
necessarily mutually inclusive concepts. Usually, substantial scientific and technological
developments are required before these terms can come together in a complex engineering
system.
Laboratory testing is one of the basic tools available to investigate complex interactions
of variables that exist in real service applications. Data can be developed which both have
applied engineering significance and provide insight into fundamental relationships in
engineered systems that can in turn be used as stepping stones to achieve quantum leaps in
efficiency, reliability and safety [2]. Furthermore, when compared to the costs generally
associated with corrosion (which can be around 10% of revenues [3]), and those saved
through application of corrosion testing, there can often be a cost reduction of between one
and two orders of magnitude and, in some cases, more.
NEED FOR SIMULATED-ENVIRONMENT TESTS
The need for simulation varies greatly depending on the purpose of the test. For example,
corrosion tests are usually conducted for three reasons [4]: screening-comparison of the
response of two or more materials or material conditions relative to a particular form of
corrosion (e.g., general corrosion, local pitting or crevice corrosion, and stress corrosion
cracking); qualification-verification that the material has a required conformance to
composition and that the metallurgical or fabrication processes have resulted in a
microstructure that will provide adequate corrosion performance; evaluation-assessment of
the influence of process changes (e.g., temperature, additives, inhibitors, and product purity).
In many cases, relatively simple, standardized tests found in NACE, ASTM, and ISO
documents can be conducted that are useful for these purposes. These are relatively simple
environments often involving combinations of acids and salts that can be handled in standard
glassware. [5-7]. However, a limitation common to many standardized tests is the difficulty
in obtaining a direct correlation between the performance in such tests and actual in-service
performance. To expand the applicability of standardized tests, substantial development work
is often required which establishes such correlations. This work usually includes one or more
of the following: review of service or failure records on a range of material conditions or
over a range of process variables, analysis of field or in-plant tests in actual service
environments, and use of laboratory exposure tests conducted under simulated service
conditions. In many situations, the laboratory provides the most convenient avenue since it
yields firsthand data that allows the engineers to make the fine distinctions in performance
required to select the most cost-effective corrosion mitigation or control methods, and thereby
gives the maximum cost benefit.
THE REASONABLE WORST-CASE SCENARIO
In the study of corrosion in simulated environments, the concept of a reasonable worstcase scenario has been a guiding light for those involved. Being reasonable includes two
aspects: reasonable levels of corrosive severity and reasonable involvement of expense and
time. It is often necessary to refine the set of exposure conditions by a process of
38
Kane
prioritization so that only the most important variables related to the operable corrosion
mechanisms are taken into account and thereby minimize testing costs. Keeping these two
aspects in mind, one must first define and preserve the active in-service mechanism(s) of
corrosion. Once this has been completed, one must identify the aggravating and mitigating
factors that combine in the actual service condition to determine the severity of corrosion.
SIMULATED ENVIRONMENT TEST PROCEDURES
Several case studies are presented herein which highlight a few of the basic, yet
important, concepts which provide the link between the laboratory and field conditions.
Case Study No. 1: Simulation of Conditions of Deaeration or Aeration
One of the most important and universally applicable situations that must be evaluated
when conducting laboratory tests in simulated service environments is the need to produce a
reasonable representation of the level of deaeration or aeration found in the actual
environment. The main reason for the importance of this effect is that corrosivity, in many
service applications, can change dramatically with changes in oxygen content. Aeration
accelerates anodic corrosion processes with a concomitant increase in localized corrosion
activity (i.e., pitting, crevice attack and stress corrosion cracking). Examples of oxygen
effects can be seen in applications such as seawater injection, the use of heavy brine
completion fluids in oilfield operations and desalination. As shown in Fig. 1, the corrosion
rate of steel increases by an order of magnitude going from 10 ppb to just 100 ppb [8]. It only
takes very low levels of oxygen contamination (about 1% of normal atmospheric saturation
levels) to greatly accelerate corrosion.
Furthermore, due to the sensitivity of corrosion reactions even in low levels of aeration,
oxygen contamination can produce excursions to higher corrosion rates that have prolonged
effects [9]. The increase in localized anodic attack produced by aeration can be illustrated by
its interaction with other species such as chlorides and sulfides. An example, in terms of
susceptibility to stress corrosion cracking (SCC), is the interaction between dissolved oxygen
and chlorides in elevated temperature applications involving alkaline phosphate treated boiler
water [10]. As the availability of oxygen increases above the 0.1 ppm (100 ppb) level, the
tolerance for chloride is reduced resulting in a dramatic increase in susceptibility to SCC.
39
Plenary Lectures
40
Kane
technique is valid since the contribution of liquid phase density and viscosity on the resultant
shear stress predominates over that of the gas phase.
Plenary Lectures
effects have only been qualitatively investigated. Therefore, when simulating service
applications, the exact nature of the oil phase should be considered since it may play a major
role in the overall corrosivity of the system and in the efficacy of inhibitor treatments.
Furthermore, the presence of the nonconductive oil phase in multiphase tests can also produce
confusing results when electrochemical techniques are used as the sole basis for evaluation.
Care must be utilized in the selection of corrosion monitoring techniques and the comparison
of this data with the results of physical examination, mass loss and localized corrosion
measurements.
Table 1. Flow/Shear Stress Relationships
Description
Relationship
VD
Determine dimension-less
Re =
0 .182
e
Kane
simple immersion or atmospheric tests. One such case that illustrates this situation is
exhibited by corrosion under insulation (CUI).
Plenary Lectures
Two major concerns when simulating service conditions in the laboratory are the
changes in severity that may be caused by depletion of reactive constituents in the corrosive
environments and build-up of corrosion products or by-products. Both can modify the
corrosivity of the environment to produce a variation in the severity of corrosion from that in
the service application. Therefore, periodic monitoring of the laboratory environment may be
required to determine the rate of consumption or build-up of various species. Additionally,
replenishment may be necessary to eliminate the undesirable effects that they can produce.
Figure 4. Corrosion under insulation (CUI) cell designed by CLI International, Inc.
Figure 5. Instantaneous and mass-loss corrosion rates for a corrosion under insulation (CUI)
system
An example illustrating these situations is industrial applications having high partial
pressures of carbon dioxide (100-600 psia) in combination with low to moderate hydrogen
44
Kane
sulfide partial pressures (0.01 to 1.0 psia). These conditions illustrate the importance of both
liquid and gas phase replenishment in these high CO2/low H2S systems. In such systems, the
steel corrosion product (Fe+2) is soluble in the aqueous phase at low to intermediate
temperature (< 60 oC). Additionally, this reaction is accompanied by an increase in the HCO3 concentration, which has a buffering effect resulting in increased pH. These factors can
result in the premature formation of a protective FeCO3 scale. Furthermore, corrosion will
also tend to consume the initial low-level supply of hydrogen sulfide. These three effects, if
not controlled, will generally result in an artificially low corrosion rate for steel when
compared to the service application. An autoclave procedure is needed for replenishment of
the gaseous and/or liquid phases so that the test duration can be prolonged and accurate
corrosion assessment can be achieved [24]. Additionally, in most cases, replenishment
procedures should be combined with the careful use of a large solution volume to specimen
surface area ratio to achieve optimum results.
In cases where a low hydrogen sulfide partial pressure is being utilized, special care must
be taken to maintain the intended amount of this reactive constituent. The difficulty in this
process increases directly with the corrosion rate of the materials being tested, the total
specimen surface area and decreasing hydrogen sulfide partial pressure. The case shown in
Fig. 6 is for replenishment involving tests of corrosion resistant alloys [25]. It can be seen
that following the first gassing, the desired hydrogen sulfide partial pressure was achieved,
but it decreased to a very low level after a short exposure period. At least two more
replenishments were required to achieve acceptably constant levels of hydrogen sulfide in the
test environment.
Plenary Lectures
Kane
ACKNOWLEDGMENTS
I wish to thank the staff of CLI International, Inc. for their hard work and dedication and
also the CLI clients which have provided financial support for many technical investigations.
Both have been essential, and have contributed greatly to the development and use of the
techniques highlighted in this paper. I also give my appreciation to Ms Delia Cuellar, who has
worked and collaborated with me for many years. Thanks are also given to those key people
who have helped to provide a guiding light into the practical applications of laboratory
testing: Dr. J Brison Greer, Mr. Walter K. Boyd, Professor Joe Payer, Dr. Peter Rhodes and
Mr. Bill Ashbaugh.
REFERENCES
1. K. Lewis, Corrosion and Failure Prevention Using Appropriate Materials Selection
during Design: Better, Cheaper, Faster, Safer, Presentation at the Golden Gate
Materials Technology Conference, San Francisco, California, February 1-3, 1995.
2. J.H. Payer, Increased Reliability and Useful Life through Better Understanding of
Corrosion Processes, Plenary Lecture, Seventh Middle Eastern Corrosion Conference,
Bahrain Society of Engineering/NACE International, Manama, Bahrain, February 2628, 1996, pp. 50-53.
3. B.C. Syrett, Cost Effective Corrosion Control in Electric Power Plants, Plenary
Lecture, Seventh Middle Eastern Corrosion Conference, Bahrain Society of
Engineering/NACE International, Manama, Bahrain, February 26-28, 1996, pp. 1-18.
4. J.W. Spence, et.al., Planning and Design of Tests, Corrosion Tests and Standards, R.
Baboian, ed., MNL 20, ASTM, West Conshohocken, Pennsylvania, 1995, pp. 33-39.
5. ASTM G31, Standard practice for laboratory immersion corrosion testing of metals,
ASTM Annual Book of Standards, Section 3.02, West Conshohocken, Pennsylvania.
6. ASTM A262, Standard practices for detecting susceptibility to intergranular attack in
austenitic stainless steels, ASTM Annual Book of Standards, Section 3.02, West
Conshohocken, Pennsylvania.
7. ASTM G48, Standard test methods for pitting and crevice corrosion resistance of
stainless steels and related alloys by the use of ferric chloride solution, ASTM Annual
Book of Standards, Section 3.02, West Conshohocken, Pennsylvania.
8. J.W. Oldfield and B. Todd, Corrosion considerations in selecting metals for flash
chambers, Desalination 31, 1979, pp. 365-383.
9. A. Ikeda et.al., Corrosion Behavior of Low and High Alloy Tubular Products in
Completion Fluids for High Temperature Deep Wells, Paper No. 46, NACE
Corrosion/92, March 1992, NACE, Houston, Texas.
10. M. Fontana, Corrosion Engineering, 3rd edition, McGraw-Hill, Inc., New York, 1986.
11. R.D. Kane and S. Srinivasan, Socratestm: Selection of Corrosion Resistant Alloys
through Environmental Specification, CLI International, Inc., Houston, Texas, 1996.
12. C.A. Palacios and J.R. Shadley, CO2 Corrosion of API N-80 Steel at 71oC (160oF),
Paper No. 476, NACE Corrosion/91, March 1991, NACE, Houston, Texas.
13. X. Zhou and W.P. Jepson, Corrosion in Three Phase Oil/Water/Gas Slug Flow in
Horizontal Pipes, Paper No. 26, NACE Corrosion/94, March 1994, NACE, Houston,
Texas.
47
Plenary Lectures
14. Course Materials, MAPStm - Multiphase Autoclave Pipeline Simulator, Short Course
on Corrosion Test Methodologies for Inhibitor Evaluation, CLI International, Inc.,
Houston, Texas, 1995.
15. S. Srinivasan, Internal report on flow modeling for laboratory simulation of field
effects, CLI International, Inc., Houston, Texas, 1995.
16. W.P. Jepson, The Effect of Multiphase Flow on the Performance of Corrosion
Inhibitors in Oil and Gas Pipelines, Seventh Middle Eastern Corrosion Conference,
Bahrain Society of Engineering/NACE International, Manama, Bahrain, February 2628, 1996, p. 80.
17. K.D. Efird et al., Experimental Correlation of Steel Corrosion in Pipe Flow with Jet
Impingement and RCE Laboratory Tests, Paper No. 81, NACE Corrosion/93, March
1993, NACE, Houston, Texas.
18. K.D. Efird, Petroleum Testing, Corrosion Tests and Standards, R. Baboian, ed., MNL
20, ASTM, West Conshohocken, Pennsylvania, 1995, p. 354.
19. W.G. Ashbaugh, Corrosion under thermal insulation, Metals Handbook Volume 13:
Corrosion, 9th edition, ASM International, Materials Park, Ohio, 1987, p. 1145.
20. Private Communication, W.G. Ashbaugh, D. Abayarathna, R. Kane (CLI
International, Inc., Houston, Texas) N. McGowen (Elisha Technologies - Moberly,
MO), March 1996.
21. ASTM G59, Standard practice for conducting potentiodynamic polarization resistance
measurements, ASTM Annual Book of Standards, Section 3.02, West Conshohocken,
Pennsylvania.
22. ASTM G1, Standard practice for preparing, cleaning and evaluating corrosion test
specimens, ASTM Annual Book of Standards, Section 3.02, West Conshohocken,
Pennsylvania.
23. ASTM G46, Standard practice for examination and evaluation of pitting corrosion,
ASTM Annual Book of Standards, Section 3.02, West Conshohocken, Pennsylvania.
24. Course Materials, MARStm - Multiphase Autoclave Replenishment System: Short
Course on Corrosion Test Methodologies for Inhibitor Evaluation, CLI International,
Inc., Houston, Texas, 1995.
25. Private Communication, M.S. Cayard to R.D. Kane (CLI International, Inc., Houston,
Texas, March 1996.
26. R.D. Kane, High Temperature and High Pressure Testing, Corrosion Tests and
Standards, R. Baboian ed., MNL 20, ASTM, West Conshohocken, Pennsylvania,
1995, p. 108.
27. T. Honda, et al., Corrosion of ferrous materials and deposition of trace metal ions in
high purity water at high temperature, Corrosion Engineering 36, 1987, pp. 257-266.
48
ABSTRACT
All Arab Gulf States suffer from shortages in freshwater resources. The deficiency is made up for
by desalinating seawater, mainly by the multi stage flash (MSF) evaporation technique. Depending on
its design, an MSF distiller has between 16 and 39 cells, arranged in one or two decks. The basic
element of a cell is the condenser which converts the vapor into the distillate. The condenser is a
structure incorporating many components, each susceptible to a variety of corrosion forms.
The lecturer will describe the fine features allowing the characterization of the types of attack
affecting the water boxes, tube-plates, tube supports and the tubes themselves. Counter measures
necessary to remedy the defects and/or eliminate their causes will be mentioned.
Vapor side corrosion of condenser tubes made of copper-base alloys will be high lighted. Attack
causes the thinning of the tube walls and the contamination of the distillate by copper above
permissible limits.
A number of operational processes affect the corrosion of MSF condensers. The roles of
seawater chlorination, ferrous sulphate dosing, scaling and ball cleaning, acid cleaning and distiller
outage will be treated in some detail.
Key Words:
Water boxes, tubes, tube supports and plates, vapour side corrosion,
chlorination, ferrous sulphate dosing, scaling, ball cleaning, acid
cleaning, shut-down
INTRODUCTION
All Arabian Gulf States suffer from a scarcity of freshwater resources. The available
underground water is either nonrenewable, or gradually builds up salinity as a result of
exhaustive pumping. On the other hand, rainfall over the area is scant and unpredictable, and
extends over a fairly long period of time. Potable water deficiency is remedied by
desalinating seawater. Two techniques, viz. distillation and reverse osmosis, are commonly
employed. Distillation, which represents the largest share, is generally carried out by multi
stage flash (MSF) evaporation.
An MSF distiller is a mammoth metallic structure operating on seawater at temperatures
between ambient and 100-115C. It incorporates a variety of components, each designed to
perform a definite task in the overall process of distillation. The number of stages of an MSF
unit is a design parameter and may vary between 16 and 39. A schematic presentation of an
49
Plenary Lectures
18 stage (cell) MSF distiller is given in Fig. 1. Fresh, chlorinated, settled seawater is passed
through the condensers of cells 18, 17 and 16 (heat rejection section) to raise its temperature
to 42C. Part of this water, to be used as makeup water, is deaerated and mixed with return
brine in the flash side of cell 18. Between 15 and 30% of this mixed water is rejected as
blowdown, and the rest is pumped into the condenser tubes of cell 15, which represents the
start of the heat-gain section. As water passes through cells 14, 13, 12, etc., its temperature
rises gradually. Following cell 1, the water passes through the brine heater to bring its
temperature up to the top value for distillation. Coming out of the brine heater, the water
goes through the flash chambers of the various cells in the reverse direction of flow in the
condensers, i.e., cells 1, 2, 3, and so forth. The water distills under vacuum, and its
temperature progressively decreases.
The basic element of a cell in an MSF evaporation unit is the condenser which converts
the vapor into distillate. The condenser is a multicomponent structure comprising the water
boxes, the tube plates, the tube supports and the tubes themselves. A typical condenser is
represented diagrammatically in Fig. 2. During operation, all parts of the condenser suffer
corrosion in a variety of ways, depending on the material they are manufactured of. It is
estimated that between 80 and 85% of distillers outages are the result of defects occurring in
the condenser system, in particular the tubes. The shape of failure can in many instances be
the same, but its causes may differ widely. The choice of the necessary countermeasures
depends, therefore, on the successful deciphering of the fine features of attack.
The present paper describes the different forms of corrosion which affect the four basic
components of condensers in MSF distillers. The material included is largely based on
observations made by the author in the Umm Al Nar Power and Desalination Plant (Abu
Dhabi, UAE) during the past 14 years. The presentation is of an orientative nature and is
intended to serve a wide spectrum of people. For the normal operator, with little or no
experience in corrosion, it is an introduction to the subject. For the operation engineer it
evokes awareness and interest in material performance. For the corrosion specialist, it lists
alternative countermeasures. No attempt is made to deal with the theory of metal corrosion.
For the first two categories of persons this is not necessary, while for the specialist the
information is assumed to be well known. The reader must, however, be well aware of the
terms associated with the common forms of corrosion, viz. general- (uniform-), galvanic(bimetallic-), crevice-, pitting-, intergranular-, dealloying- and erosion-corrosion, as well as
corrosion cracking.
Further, it is beyond the scope of the present paper to enlist all materials suitable for
constructing part or all of the condenser system of MSF plants. Broadly speaking, these fall
into four classes: mild- and carbon steels, stainless steels, copper-base alloys and titanium
alloys. Details of the composition of these materials, their physical properties and their
corrosion characteristics are well documented [1-15].
50
Shams El Din
51
Plenary Lectures
Shams El Din
corrosion will require removal of the defective area and careful repair welding. Most cases of
water box failure can be eliminated through cathodic protection using sacrificial iron anodes.
The released ferrous ions also improve the corrosion resistance of the copper condenser tubes
and tube plates.
CORROSION OF TUBE PLATES
Tube plates are commonly manufactured from stainless steel or copper-base alloys (i.e.,
brasses, bronzes, and cupro-nickels). These materials are used as such or are clad over Csteel. The choice of plate material is made on the basis of mechanical characteristics, cost
considerations and compatibility to condenser tubes.
Depending on their composition, and the operational and environmental conditions, tube
plates undergo different forms of corrosion:
Erosion-Corrosion
This results from the impact of seawater at velocities higher than design the values, from
impingement attack by entrained gas bubbles or from abrasion with sand loaded water. The
metal surface assumes a rough touch and acquires a shiny silver or golden luster due to the
loss of the natural protective film. Attack need not cover the whole plate since turbulence and
vortices are not equally distributed on the surface. Countermeasures against erosion-corrosion
involve the reduction of flow velocity, the removal of suspended material from the circulating
water and the release of entrapped gases. Severely attacked plate areas are ground and filled
with a neutral coating. Ferrous sulphate dosing improves surface film resistance to erosioncorrosion.
Crevice Corrosion
Tube plates may undergo crevice attack when covered by nonconducting material (e.g.,
polythene sheet, paint flakes etc.). In heat-rejection cells, barnacles and shell animals
continue to strive and stick to the surface of tube plates. During their life the organisms produce
organic nitrogen and sulphur compounds which intensify the attack on copper alloys. The
released copper ions eventually kill the animal, and crevice attack continues thereafter by way
of an oxygen concentration cell mechanism.
As a result of the large thickness of the tube plate, it is improbable that crevice attack
will continue undetected till it cuts through the metal. The water box is likely to be opened,
for one reason or the other, at which time preventive and corrective measures are undertaken.
These involve screening water properly at the intake, raising the chlorination level to
discourage the entry of marine organisms, and cleaning and filling present crevices with
neutral filling followed by a coat of hard epoxy resin.
Crevice/Galvanic Corrosion
Another type of tube-plate failure develops on claded plates with imperfect tube holes.
Expansion of the tubes leaves behind narrow spaces which are filled with seawater.
Corrosion starts as crevice corrosion until the water reaches the base metal under-covered
where the attack is accelerated as galvanic corrosion. Left for a long time, attack might eat
through the thickness of the plate. During its early stages, when the crevice corrosion is only
operative, corrosion might escape the attention of the inexperienced or hasty eye. Careful
53
Plenary Lectures
examination will reveal, however, tiny recessions between the tubes and plate. A steel needle
tip will measure the depth of attack. During the galvanic phases however, corrosion is
recognized by the brown stains of iron oxides oozing from between the tubes and the plate.
Counter-measures against crevice/galvanic attack involve the rerolling (re-expansion) of the
tubes. In most cases, this proves to be adequate for eliminating the clearance between the
tubes and the plate. If this fails, more stringent measures are undertaken. These involve the
thorough cleaning of the inside of the dried crevice with the help of steel needles until it is
free of corrosion products. An air compressor producing a micro-jet might prove useful.
This is followed by the intrusion of a natural fill and a cover with a hard epoxy resin. When
the claded tube plate and the tubes are of the same material, welding after cleaning presents
another practical alternative.
Corrosion by Dealloying
Tube plates made out of uninhibited brasses (i.e., copper-zinc alloys) undergo rapid and
severe dezincification by seawater, especially at high temperatures. Dealloying occurs in
patches in what is commonly referred to as plug-type attack.
Naval brass (i.e., brass with 0.5-1.0% tin) undergoes differential attack in which the
defected areas are covered with easily detachable scales of the corrosion products. This type
of attack is designated as exfoliation or layer-type corrosion.
Uninhibited brasses should not be used as tube plates in condensers operating on
seawater. Their use in small units is not due to good performance but to over-dimensions
which prolong their life span.
Dezincification is remedied by grinding the dealloyed areas and filling the depressions
with an appropriate neutral material. The whole plate surface, and preferably, the tube ends
as well, are coated with an approved epoxy resin. Cathodic protection with sacrificial mild
steel anodes will ensure stiffing of corrosion should the coat fail.
CORROSION OF CONDENSER TUBES
Failure of condenser tubes constitutes the largest cause of distiller outages, so the choice
of tube material is accordingly crucial. Tubes have to have reasonably high thermal
conductivity, sufficient ductility to expanded into the tube plate, and their corrosion
performance should be well understood. Last but not least is the question of cost. Three
types of materials present themselves. These are copper-base alloys, stainless steels, and
titanium. Each possesses its own merits and limitations, and will be treated separately.
Corrosion of Copper-Base Condenser Tubes [19-29]
Copper-base alloys suitable for manufacturing condenser tubes encompass the brasses,
the bronzes and the cupro-nickels. Simple brasses are 70/30 copper-zinc alloys, occasionally
with 0.5-1.2% tin or lead [12]. These must be inhibited by minute amounts of arsenic,
antimony or phosphorus to prevent dezincification. Aluminium brasses are a family of
copper-zinc alloys containing between 1.8 and 2.5% aluminium, with minor quantities of
iron, nickel, manganese and lead. Tubes of these brasses exhibit excellent resistance to brines
at high temperature. They do, however, suffer erosion-corrosion at flow rates above about 2
ms-1, and are not immune to polluted (i.e., H2S and NH3) seawater. Their relatively low price
is, however, an appreciated asset.
54
Shams El Din
Bronzes, on the other hand, are copper-tin alloys. As a rule, simple bronzes are superior
in property to simple brasses. The reader must be aware of the confusion associated with the
nomination of bronzes [12]. Materials like aluminium bronzes (i.e., C 63700 and C 65200)
and manganese bronzes (i.e., C 67500 and C 67800) are in fact high-tensile brasses,
designated as bronzes just to praise their properties. True bronzes contain up to 13% tin. Gun
metals contain both tin and zinc; types A and LG 3 are resistant to erosion-corrosion. The
resistance is further improved through additions of 1.0-2.0% nickel as in Admiralty gun metal
G1. An important material for condenser tubes running on seawater is the so called AP
bronze, which contains 8% tin, 1% aluminium and 0.1% silicon. In contrast to aluminium
brass, AP bronze withstands corrosion by H2S-polluted seawater. Its life expectancy is
estimated to be 2-4 times that of aluminium brass [30,31]. In nonpolluted seawater,
aluminium brass is preferred to aluminium bronze on the basis of cost [32].
Copper and nickel are freely soluble in one another and form an extended solid solution.
A large number of alloy compositions were prepared and their resistance to corrosion by
seawater was evaluated [33]. Two alloys, viz. the 90/10 and the 70/30 were specially
attractive, particularly after the discovery of the beneficial effect of small additions (up to
2%) of iron and manganese. As tube materials, the cupro-nickels withstand flow velocities
up to 6.0 ms-1 [34] and are fairly resistant to fouling in seawater. They are, however, easily
affected by polluted water. Nowadays condensers with tubes made of 90/10 and 70/30 cupronickels represent some 85% of all copper-base condensers. Copper-nickel alloys containing
0.5% chromium were recently reported [35,36]. These are described as exhibiting high
tolerance to erosion and impingement attack. Similar effects are achieved through additions
of solutionized iron [37].
Copper-base condenser tubes fail much in the same way; the only difference being the
extent and rate of attack. Failure is commonly manifested as a pore leading to the admixing
of the brine with the distillate. Many reasons are responsible, however, for pore production.
A clear understanding of pore morphology is, therefore, essential in establishing the cause of
corrosion and in ensuring the choice of appropriate measures to prevent the further escalation
of the problem.
From the water side, condenser tubes may fail by:
Crevice Corrosion
Crevice corrosion in condenser tubes results wherever parts thereof get covered by nonconducting materials such as seashells, barnacles, sand, clay, and damaged sponge balls.
Damage from barnacles attaching themselves to tube walls is limited to the cells of the heat
rejection section where environmental conditions (i.e., temperature, oxygen content, and
nutrients) still allow their growth. Barnacles can anchor anywhere along the tubes length
and induce corrosion by way of depleting oxygen and secreting harmful chemicals. Due to
gravity, under-deposit attack develops at the bottom of the tubes. Very seldom, do they cross
the five and seven oclock limits. Another feature characterizing crevice attack is that the
pore lies in the centre of a clear imprint of the cover that initiated the attack. Elongated pores
follow, in most cases, the flow direction although oval cuts with their major axes
perpendicular to the flow have been recorded. A linear succession of pores along the tubes
length indicates a thick sand or clay deposit. Contrary to some claims [38], crevice attack
55
Plenary Lectures
does not develop under alkaline scales. The main constituents of the scales, CaCO3 and
Mg(OH)2, act as anodic inhibitors.
Crevice corrosion of condenser tubes can be stopped or greatly reduced by controlling
the entry of undesirable material. This requires the proper functioning of the band screen and
the appropriate chlorination of the feedwater to discourage marine life inside the lowtemperature cells. Dead shells and barnacles do not adhere to tube walls. Prolongation of the
time of stagnation in the settling basins helps prevent the accumulation of sand and silt inside
the tubes. The use of Tapproge ball cleaning, brush cleaning and back-flushing of the tubes
during shutdown, and the eventual acid-washing of the distiller remove tenaciously held
deposits and bodies.
Stress-Corrosion Cracking (SCC)
The expansion of tubes in the tube plate results in the accumulation of stresses along the
diameter-change zone. Although these stresses are within the range of the design values, they
induce, on the long run, the cracking of the tubes. Cracking takes the form of a
circumferential cut, perpendicular to the direction of flow. The cut is located only a few
centimeters from the tube edge and can readily to be ascertained with an inspecting finger.
Metallographic examination reveals that cracking is mainly intergranular [28] but
transgranular attack is not uncommon. The frequency of failure at tube inlets exceeds by far
that at outlets, suggesting that turbulance assists cracking. Stress corrosion cracking (SCC) of
aluminium-brass tubes has been recorded in the first cells of the heat-gain section of the
distiller [39]. In the high temperature cells, tubes of 70/30 cupro-nickel sometimes exhibit
failure features very similar to those of aluminium-brass. Corrosion of 70/30 cupro-nickel by
SCC has not been reported before, and the matter requires further investigation [40].
SCC requires special agents for initiation. Three materials for copper-base alloys are
recognized, viz., ammonia, hydrogen sulphide and mercury. The first two result from
decomposition of marine organisms and/or sewage discharged into the sea. Pollution by
mercury comes mainly from industrial activities in the vicinity of the desalination plant.
Chlorination of seawater at the intake removes ammonia and hydrogen sulphide. Sewage
treatment on land before discharge into the sea removes or reduces the amounts of the two
pollutants. Application of special paints to tubes ends isolates the areas susceptible to attack.
In Abu Dhabi the problem of SCC of aluminium-brass tubes was controlled through cathodic
protection of the water boxes, tube plates and tube terminals by sacrificial iron anodes [39].
Already perforated tubes are recovered through tube inserts. These are either metallic, in
which case they must be galvanically compatible to the tubes and tube plate, or of man-made
materials. In this last case they should not be made of nylon or amide-based polymers. These
substances readily hydrolyze in seawater to yield ammonia which promotes cracking.
Erosion-Corrosion
Erosion-corrosion of copper-base condenser tubes, occurs whenever the naturallydeveloped- or artificially induced film on their surface is destroyed [41-43]. This happens
when the water flow rate exceeds the upper limits of tolerance of the material. Erosion is
manifested in the form of grooves, gullies, waves, rounded holes or horse-shoes, lined up in
the direction of the flow. Erosion is more prominent at tube inlets due to turbulence. It
produces a rough surface which ends where the flow turns laminar. Erosion-corrosion can
proceed till complete failure occurs, producing pores elongated along the direction of flow.
56
Shams El Din
The rate and extent of attack increases when the water carries suspended sand or entrained
gases.
Counter-measures against flow-induced attack involve reduction of the water flow rate,
extension of the time of stagnation in sedimentation basins, and controlled use of ball
cleaning. Excessive ball cleaning, especially when of the hard type, removes the inhibiting
film from inside the tubes. Filming by ferrous sulphate or through sacrificial iron anodes will
restore the film. Too much chlorination of seawater at the intake is also detrimental to the
passivating film. Eroded tube inlets are repaired with appropriate tube inserts.
Corrosion by Polluted Waters
Polluted seawater contain ammonia and/or hydrogen sulphide. Both materials are
products of the decay of dead animals and organisms. The two pollutants attack copper
condenser tubes.
Hydrogen sulphide reacts spontaneously with copper tubes to produce a black, porous
copper sulphide film. Being nonprotective, the film allows further attack until the metal is
eaten through [44-49]. Attack is more rapid if the polluted water is loaded with slime and silt.
Under the slime, attack by sulphide is considered a special type of deposit corrosion in which
metal deterioration is initiated by the presence of hydrogen sulphide rather than by a
deficiency in oxygen.
Attack by sulphide-polluted water is identified by the black coloration of the tube inside.
Treatment of the black film with dilute acid sets free the hydrogen sulphide, known by its
characteristic bad odor. On the micro-scale range, the presence of sulphide is ascertained
through its catalyzing the evolution of nitrogen gas bubbles from a drop of iodine-sodium
azide solution. The test is carried out under a magnifying lens or microscope.
Sulphide corrosion can be dealt with in a variety of ways. Suitable tube material can be
chosen if it is known from the start that only polluted water is available. Extension of the
intake facilities away from the source of polluted water is a second alternative. When present
in small amounts, hydrogen sulphide is oxidized by chlorination. This must, however, be
carefully controlled. The same also applies to rubber ball cleaning if sulphide-polluted sludge
is in abundance.
Seawater polluted with ammonia affects the corrosion of copper base condenser tubes in
two distinct ways: it induces SCC and the rate of crack propagation increases with pollutant
content; and ammonia and ammonium salts enhance the general attack by dissolving and
complexing with the copper ions. The tubes lose their protective film and acquire a shiny
appearance. Eventually the tubes fail when they become perforated at weak points. Failure
can occur anywhere along the tube length and the resulting pore takes any form. Ammonia
attack is suspected when daily analysis of the brine shows a constant, high level of copper.
There is no direct solution to the problem of corrosion by ammonia-polluted seawater. If
the source of pollution is permanent, relocation of the seawater intake might prove practical.
If pollution is widespread, a change to ammonia-resistant tubes, e.g., titanium or stainless
steels, might be considered. Chlorination of ammoniated seawater is effective in removing
low levels of pollution. The two agents react to produce chloramines which are weaker
disinfectants than chlorine itself. The formation of chloramines reduces, but does not
completely eliminate the problem of ammonia-corrosion since chloramines readily hydrolyze
57
Plenary Lectures
to the original harmful material. Ferrous sulphate dosing retards the aggressive action of
small amounts of ammonia by forming an inhibiting ferric oxide film.
Corrosion of Stainless Steel Condenser Tubes
There is a wide variety of stainless steels that can be used as condenser tubes in MSF
distillers [7,50-52]. In flowing seawater, the performance of stainless steel tubes is quite
satisfactory. They withstand general corrosion and are not affected by the flow velocities
operating in a distiller. Normal steels are susceptible to SCC in solutions of high chloride
content at high temperatures. As the tubes are not subject to any noticeable stresses, this type
of attack is unlikely to develop. In stagnant solutions, on the other hand, normal stainless
steels are liable to undergo pitting corrosion [53-56]. During a long outage, the distiller must
be carefully drained and flushed with ample quantities of potable water to prevent chloride
attack. Stainless steel tubes are also prone to crevice corrosion, which develops under
barnacles, stuck rubber balls and the like. The same procedures described in case of copperbase tubes apply in such cases.
Weld areas and the heat affected zones are weak points where intergranular and pitting
attack readily propagate on stainless steel in a desalination unit [57,58]. Spot and arc welding
is to be applied, and annealing should be carried out whenever feasible. Finally, stainless
steel tubes mounted on copper-base tube plates will lead to their rapid deterioration by
galvanic action [59-62]. Cathodic protection using sacrificial mild steel anodes overcomes
this problem.
Corrosion of Titanium Condenser Tubes
Titanium tubes exhibit excellent resistance to general-, pitting- and crevice corrosion.
They withstand erosion-corrosion and impingement attack at flow velocities as high as 20
ms-1. They are also immune to SCC and are unaffected by polluted seawater. Titanium has,
however, a low thermal conductivity, and this is resolved by reducing the tube wall thickness.
To compensate for the loss in rigidity, a larger number of tube supports are installed.
Titanium tube plates are expensive, and the expansion of titanium tubes, therein, can lead to
crevice corrosion [65,66] at temperatures at and above 80C. Organic sealants (e.g.,
dimethacrylate) used to fill the tube/ tube plate interface worsen rather than improve the
situation, as crevice corrosion starts at about 80C [66]. Two alternatives can be applied to
prevent titanium/titanium crevicing. The first involves seal welding and this has the
advantage of preventing crevice attack completely. It has, however, the drawbacks of being
expensive and requiring skilled personnel. The second procedure is the coating of the
titanium tubes/tube plates with a palladium oxide (PdO)/titanium oxide (TiO2) mixture. The
coating is prepared in situ from a mix solution of palladium chloride (PdCl2) and titanium
chloride (TiCl3) followed by thermal oxidation in air [67]. This type of sealant prevents
crevice attack in 15% NaCl of pH 3 at 120C [67].
The mounting of titanium tubes on copper-base tube plates prevents the crevice
corrosion of the tubes. However, because of the large difference in their free corrosion
potentials, titanium induces the galvanic corrosion of the tube plate [62,66,68]. To stop
attack, cathodic protection of the plate and tube ends by impressed currents [69,70] or
sacrificial anodes [71,72] has been suggested. Unless very carefully controlled, protection
can do more harm than good. Protection should not reduce the potential of titanium to lower
58
Shams El Din
than -0.50 V versus the saturated calomel electrode (SCE) [66] or -0.65 V versus SCE [71].
Polarization to more negative potentials will cause the absorption of hydrogen in titanium and
the formation of titanium hydride. This causes a loss of ductility and cracking of the tubes.
Normal mild steel is not recommended as anode material as it shifts the potential of titanium
to values more negative than those recommended for safe protection. An iron/9% nickel
alloy is recommended to keep the potential at the desired value [66]. A recent study from this
Laboratory [73] revealed that hydrogen uptake by titanium can take more than one form,
depending on the type of anode used.
Titanium tubes are not recommended for use in the high temperature cells and in the
brine heater, where they are likely to pick up hydrogen from the hot brine. In their place,
tubes of 70/30 cupro-nickels can be installed.
CORROSION OF TUBE SUPPORTS
Tube supports are elements of MSF distillers not readily accessible for inspection and
repair. The functions of tube supports are to keep the tube bundle in position, to act as guide
for long tubes and to prevent the tubes from sagging and vibrating. Because tube supports are
exposed to deaerated steam, they were assumed to suffer no corrosion. Accordingly, they
have been made of the cheapest material, viz. mild steel. In fact, however, mild steel tube
supports are heavily corroded by reaction with steam as well as by galvanic contact with the
nobler material of the tubes. By the time the supports change into iron oxide lumps which
make it extremely difficult, if not completely impossible, to extract failed tubes or retube the
condenser. There is nothing that can be done to save C-steel supports in contact with
stainless steel, copper alloys or titanium tubes, from completely failing. Nowadays tube
supports are specified to be of the same material as the tubes themselves.
VAPOR-SIDE CORROSION
Until now, we have considered the forms of corrosion affecting components of MSF
condensers in contact with seawater. Cases have also been recorded, where corrosion occurs
on the vapor side. One such case has already been mentioned, namely, the corrosion of Csteel tube supports bearing condenser tubes.
Occasionally reference is made to the vapor side corrosion of copper-base condenser
tubes [74,75]. Such attack is recognized through shining tube surfaces, an outside reduction
in wall thickness and an above-normal (>0.1 ppm) increase in the Cu2+ content of the
distillate. This occurs mainly in the high temperature cells of the distiller. The general belief
[76] is that the vapor is largely contaminated with CO2 resulting from the high temperature
decomposition of the HCO -3 ion of the brine [95]. The formed carbonic acid, H2CO3, is
assumed to be sufficiently strong at high temperatures to attack the copper tubes. Apparently
this explanation is an over simplification of a more complex process. At the temperatures of
the first heat gain cells, the solubility of CO2 in the vapor is both limited and transient.
However, neither copper nor its alloys displace hydrogen from acid solutions. If H2CO3 is to
exert a corroding action it must do so by dissolving the cuprous and cupric oxides formed on
the metal surface. Practical experience confirms this conclusion. Condenser tubes
undergoing overhaul acquire black coloration as a result of air oxidation. When returning to
service, the distillate exhibits above-normal copper-content and has to be dumped back into
59
Plenary Lectures
the sea. Considerable time (up to 60 hours [75]) elapses before the copper concentration in
the distillate returns to permissable limits. For copper tubes to continue corroding, their
surface has to reoxidize. This occurs through the oxygen (air) dissolved in the flashing brine.
As this is limited, the rate of corrosion falls to low values. Higher corrosion rates point to
the presence of tiny leaks in cell gaskets. A vacuum leak test (or pressure leak test) on the
distiller will confirm this assumption.
Vapor-side corrosion of copper condenser tubes can be serious if seawater is polluted by
ammonia or hydrogen sulphide. What has been said regarding water-side corrosion applies to
vapor-side corrosion too.
OPERATION PROCESSES AFFECTING CORROSION IN MULTI STAGE FLASH
(MSF) DISTILLERS
In running an MSF plant, certain processes are carried out the aim of which is to
overcome an operational difficulty and/or to improve production efficiency. These processes
affect the corrosion of distiller components in variety of ways. In some instances, the role of
a certain parameter can be beneficial at one level and detrimental at another. The successful
operation of the distiller depends, therefore, on a proper understanding and careful execution
of the process. The following operations deserve special mention:
Chlorination of Seawater
Chlorination of seawater at the intake is carried out to discourage marine organisms from
entering the distiller and to prevent bifouling. There is no single chlorination procedure that
applies to all units. The adoption of a certain course of action evolves from trial and error and
depends on factors such as geographic location, bioactivity, temperature, and water purity.
For example, in Umm Al Nar (Abu Dhabi) chlorination is carried out continuously to a level
of 0.4 ppm. This ensures a residual chlorine content of about 0.25 ppm in the condenser
tubes. To prevent organisms from building up resistance, shock dosing at 1 ppm is achieved
for 1 hour. once a week [78]. Chlorine reacts with water to produce hydrochloric and
hypochlorous acids : Cl2 + H2O = HCl + HClO. Both acids are directly neutralized by
seawater alkalinity. The hypochlorous ion, ClO-, is a strong oxidizing agent which raises the
free corrosion potentials of alloys to higher values. This raises the susceptibility of normal
stainless steels to pittings- and crevice corrosion, particularly in regions of stagnation [79].
Similarly, chlorination of seawater interferes with the process of ferrous sulphate dosing.
Chlorination is stopped before, during and for some time after dosing to allow the iron-oxide
film the chance to build up properly. On the other hand, chlorine injection destroys pollution
by hydrogen sulphide, and neutralizes, to some extent, ammonia polluted seawater.
Ferrous Sulphate Dosing
Copper-base condenser tubes have little resistance to erosion-corrosion and to corrosion
by hydrogen sulphide-polluted seawater. Both types of attack are greatly inhibited by ferrous
sulphate dosing [80]. The ferrous ion readily hydrolyzes and oxidizes to colloidal FeOOH,
which adheres strongly to tube surface. The iron oxide film improves the naturally formed
copper oxide and offers better protection. Two to three hours before sulphate dosing,
chlorination of the seawater is stopped. The sulphate is injected at a rate of 3 ppm for one
hour per day for one month at tube inlets. Chlorination can be resumed after two hours.
During the second and third months, ferrous sulphate dosing is reduced to 2 and 1 ppm for
60
Shams El Din
one hour per day, successively. During the whole period of treatment, sponge ball treatment is
reduced to one or two times per week for one hour. The success of sulphate dosing is
recognized through the uniform coloration of the tube plates and tubes with a light- to deepbrown film, which does not peel off when scratched with a nail. A number of factors
interfere with film formation. These involve waters flowing at high rates or carrying large
amounts of sand, slime or deposits; excessive or continuous ball cleaning; chlorination
directly before, during or after sulphate dosing and/or the presence of entrapped, polluted
dead waters.
Scaling in Condenser Tubes
Scale formation in the condenser tubes is one of the major problems encountered during
the operation of MSF distillers. Scaling impairs heat transfer, causes tube blockage and can
induce corrosion. Scale formation is an inherent product of the composition of seawater,
which contains HCO -3 , Ca2+ and Mg2+ ions. The thermal decomposition of the HCO -3 leads
to the deposition of calcium carbonate and magnesium hydroxide. Two alternative
techniques are employed to prevent (retard) scale formation. The first involves the controlled
acidification of the makeup water to convert the HCO -3 ion into CO2. Either sulphuric or
hydrochloric acids is used; the first is preferred on the basis of cost considerations. An
addition of 100-200 ppm sulphuric acid is normally used, and the evolved CO2 is stripped off
either in a separate degassing tower or in the MSF vacuum deaerator. Unless very carefully
carried out, acidification can lead to serious corrosion of the condenser tubes and the
deaerator system. To overcome this problem under-acidification has been proposed [81].
Laboratory experiments have shown that 80% of the acid required to completely neutralize
the bicarbonate ions is sufficient to prevent scale formation for a long time [82]. Another
technique to prevent corrosion involves the neutralization of excess acid. Following
degassing, the brine pH is brought back to ~7.5 through the controlled addition of caustic
soda. This technique is elaborate and expensive [83].
The second approach for scale prevention is the use of antiscaling agents. These are
polymeric, surface-active substances which adsorb on active centers of CaCO3 and Mg(OH)2
crystallites. This inhibits them from forming a continuous layer. A small amount of the
inhibitor (2-5 ppm) is needed to retard scale formation, and the method is known as a
threshold treatment [84]. A large variety of antiscalants is available on the market, and the
nature of the scale depends on the compound used. Polyphosphates, for example, give rise to
dense, fluffy, grayish-brown deposits [85]. Maleic anhydride polymers, on the other hand,
yield thin, hard scales [86].
A hybrid technique for scale control has been suggested [87]. It involves the use of lessthan-stiochiometric quantities of a mineral acid together with small quantities of a threshold
antiscalant. Under-acidification eliminates the problem of acid corrosion of tubes, while the
removal of the largest part of the waters alkalinity allows lower concentrations of the
antiscalant to be used. This represents a sizable reduction in cost.
Sponge Ball Cleaning
The retardation of scale formation in the condenser tubes through dosing of antiscaling
agents is usually coupled with the technique of sponge ball cycling (Tapproge ball cleaning).
The rubber balls are slightly larger than the interior diameter of the tubes and are forced
61
Plenary Lectures
through by the pressure of circulating water. As they travel through the tubes, the balls wipe
out the tubes insides and prevent scale crystallites from building a solid layer. As the balls
pass randomly through the tubes, they are cycled for enough time to ensure the cleaning of
the maximum number of tubes. There is no standard procedure for ball cycling. This varies
between one or more cycles per day and continuous cycling. The duration of a cycle also
differs from one plant to another. On the market are sponge balls with different surface
hardness. The choice of the appropriate type depends on the seawater purity, type and
concentration of the additive used, nature of the deposit and distiller top temperature. A trial
to optimize sponge ball cleaning was recently published [88].
Sponge balls can affect tube corrosion in many ways. Soft balls and/or short treatment
times might be ineffective and allow sand, silt and scale deposition which lead to crevice
attack. The same result might be noted when the number of balls is insufficient. On the other
hand, balls that are too hard can induce erosion-corrosion by stripping the protective film
from the metal surface. Also, it is not uncommon for balls to get stuck inside the tubes,
promoting crevice attack. Finally, as mentioned above, ball cleaning damages the fresh iron
hydroxide film resulting from ferrous sulphate dosing.
Acid Cleaning
Antiscaling agents do not inhibit completely the formation of alkaline scales; they only
retard their growth. Even when their use is coupled with sponge ball cleaning, a scale film
continues to grow inside the condenser tubes. Due to their bad thermal conductivity, a
situation is eventually reached when the gained output ratio of the distiller drops below a
preset value. The operation of the distiller becomes impractical (noneconomical) and an acidwash of the distiller is necessary.
The washing process is carried out by circulating warm (~65C) fresh seawater through
the water boxes and condenser tubes of the cells and the brine heater. Enough inhibited acid
is added to the water to bring its pH value to 1.8-2.0. For copper-base condensers either
hydrochloric or sulphuric acids can be used. The pH of the water is monitored, and its value
rises as result of reaction with the scale. Extra acid is added to bring the pH to its lower value
and the process is repeated until no further increase in pH is recorded for a long time (usually
two hours). The acid water with the accumulated sludge is discharged, and the distiller is
flushed clean with fresh seawater. The use of an improper corrosion inhibitor [89] or
insufficient quantities of a suitable one leads to general attack on the tube material.
The same washing procedure described above applies to condensers with titanium tubes
as well. However, because of the high tendency of titanium to absorb hydrogen, weak
organic acids, e.g., citric [90] or sulfamic [91] acids are used instead. A few organic
compounds marketed under trade names, e.g., Galvane (ICI) and IBIT [91], are said to retard
acid attack on titanium.
Distiller Outage
As is clear by now, seawater is an extremely aggressive medium which attacks all of the
metallic components of an MSF unit. The fact that distillers operate for long times with little
damage is due to two main reasons:
62
Shams El Din
The ability of stainless steels to withstand the corrosive action of flowing seawater,
while being quickly and severely attacked by the same water under stagnation, and
The readiness by which copper-base alloys develop protective surface films which
offer some resistance to the action of flowing water.
Preventive and protective measures that can taken during operation are mentioned in
detail in previous sections. These involve degassing to remove oxygen (depolarizer) and
carbon dioxide (acidity) from the brine, ferrous sulphate dosing to increase the protection of
copper tubes, chlorination to discourage marine organisms from gaining access to the inside
of the distiller, use of antiscalants and ball cleaning to minimize scale formation and the
application of cathodic protection to prevent tube failure. Accordingly, as long as these
measures are observed and the distiller is operating, the corrosion of its components is largely
under control.
This well balanced system of protection is lost once the distiller is shut down. Upon
opening the water boxes and the flash chambers, air (oxygen) fills the entire unit, and
accelerates ongoing corrosion. On the other hand, brine stagnation inside condenser tubes
causes the settling of sand and silt, and occasionally a few sponge balls. This initiates crevice
corrosion. Stagnation also promotes the pitting corrosion of stainless steel components.
Unless the shutdown is for a short time (i.e., a maximum of two days) precautions against
attack should be applied. These involve the draining of the stagnant brine from the distiller,
followed by a thorough flushing with potable or distilled water. The washings should likewise
be drained out. During long outages, all inlets and outlets should be left open to remove
humidity and speed up the drying of the distillers inside. The various components of the unit
should be examined and the necessary corrective measures taken.
REFERENCES
1. T.H. Rogers, Marine Corrosion, New York: John Wiley, 1968.
2. F.L. LaQue, Marine Corrosion, New York: John Wiley, 1975.
3. D. Pecker and I.M. Bernstein, Handbook of Stainless Steels, New York: McGrawHill, chapter 14, 1977.
4. Inco, Copper-Nickel and Other Alloys for Desalination Plant, London: INCO Europe
Ltd., 1981.
5. European Federation of Corrosion Publications, No. 3, General Guidelines for
Corrosion Testing of Materials for Marine Applications, London: The Institute of
Metals, 1989.
6. European Federation of Corrosion Publications, No. 10, Marine Corrosion of Stainless
Steels, London: The Institute of Materials, 1993.
7. Nickel Development Institute, Guidelines for Selection of Nickel Stainless Steels for
Marine Environments, Natural Waters and Brines, Toronto: NIDI, vol. 2, 1987.
8. Nickel Development Institute, Materials for Saline Water, Desalination and Oilfield
Brine Pumps, NIDI, 1988.
63
Plenary Lectures
Shams El Din
Plenary Lectures
66
ABSTRACT
Large scale desalination really began with the multi-stage flash (MSF) plant built by Weir
Westgarth in Kuwait in 1960. This and similar plants elsewhere used mainly carbon steel and brass
alloys in their construction. Corrosion problems with these early plants led to costly shutdowns and
maintenance. As knowledge of the requirements of materials has grown there has been a steady
upgrading of materials and this, together with improved control of operation has resulted in much
better reliability and performance.
This paper presents a state of the art review of factors which are important in the selection and
use of materials in MSF and reverse osmosis (RO) desalination plants. Economics play an important
part in materials selection and are given consideration in general terms.
Key Words: Desalination, MSF, RO, corrosion, materials.
INTRODUCTION
Large scale desalination really began with the multi-stage flash (MSF) plant built by
Weir Westgarth in Kuwait in 1960. This and similar plants built elsewhere used mainly
carbon steel and brass alloys for their construction. Experience in these early plants,
particularly when acid-dosing was used as an antiscalant, was that corrosion problems were
often extremely severe leading to costly shutdowns and maintenance. As knowledge of the
requirements of materials to meet the conditions in MSF plants has grown, there has been a
steady upgrading of materials, and this, together with improved control of operation, has
resulted in much better reliability and performance.
This paper presents a state of the art review of the factors which are important for
selection and use of materials in MSF and reverse osmosis (RO) desalination processes. As
the risk of corrosion is always present in desalination, corrosion plays a major part in
determining material selection. Corrosion is a process involving the reaction of a material
with its environment, and this paper reviews materials for usiing incomponents in the
environments encountered in MSF and RO processes. In MSF plants these environments are
sea water, deaerated sea water and brine, distillate and incondensible gases; in RO plants they
are sea water, brackish waters and brines. Economics play an important part in materials
selection and are given consideration in general terms. For general reference an appendix is
included giving typical compositions of materials used in desalination plants.
67
Plenary Lectures
Nominal
Composition
Carbon
Copper-Bearing
0.2 5% C
0.22% C
0.31% Cu
2% Ni 0.6% Cu
Corrosion Rate
(mm/yr)
1 year
16 years
0.15
0.075
0.15
0.077
68
Oldfield
In most engineering applications sea water flows over the metal surfaces so, it is
important to have corrosion data under these conditions. Figure 1 [3] shows how flow rapidly
increases corrosion of carbon steel in sea water. This is mainly due to the increase in the
mass flow of oxygen to the corroding surface. In applications where continuous flow is
required, a corrosion rate of about 1 mm/yr can be assumed for carbon steel and cast iron.
Plenary Lectures
in general, this is found to be the case (Fig. 2). However, in MSF plants, where deaeration
occurs as part of the process, two other factors have an important effect. These are
temperature and flow rate. Few test data have been measured under controlled oxygen, flow
and temperature conditions, but Oldfield and Todd [4] have modelled the process and
compared calculated and actual test data.
Comparison with measured data [5] show that even with good deaeration, high corrosion
rates can be experienced at high flow rates and high temperatures. At low corrosion rates, the
measured and calculated corrosion rates are in good agreement, but at higher rates the
calculated values are significantly above the measured values. This was attributed to the
buildup of rust scales on the steel. Although these are not protective, they do provide a
barrier to oxygen access to the surface and reduce the rate of attack.
Corrosion of Copper Base Alloys in Sea Water
Copper alloys have been used traditionally in marine engineering for heat exchanger
tubing and for cast and wrought components in pumps and valves. These alloys form good
protective films in sea water, and provided these films are undamaged, corrosion is slight.
However, the protective films are susceptible to damage by fast flowing sea water, and this is
an important factor in selecting these alloys for applications involving flow-for example, heat
exchanger tubing. Table 2 gives data on some commonly used heat exchanger alloys.
Table 2. Jet Impingement Tests on Copper Base Alloys
Alloy
Admiralty Brass
Aluminium Brass
90/10 Cupronickel
7 0/30 Cupronickel
66/30/2/2 CuNiFeMn
In deaerated sea water copper alloys can still form protective films and show higher
resistance to corrosion than in natural water. This is because the potential of copper alloys in
sea water is much higher than the potential at which hydrogen can evolve; thus, in the
absence of oxygen, corrosion is negligible. However, as in the case of carbon steel, low
oxygen levels with high flow rates can cause impingement attack as shown by Anderson [6],
but the rate of attack was much lower than in aerated sea water. Further data on corrosion of
heat exchanger tubing alloys in deaerated sea water is given in Fig. 3 [7]. These data indicate
that at low temperatures and oxygen levels, corrosion of the three alloys tested is acceptably
low. However, at high temperatures with high oxygen levels, although the cupronickels
continue to show low corrosion rates, aluminium brass is attacked. Thus, in MSF plants,
where aluminium brass tubing is used, it is confined to the lower temperature recovery stages
with the cupronickels being used in the higher temperatures areas.
70
Oldfield
Figure 3. Effect of oxygen content on corrosion of Cu base alloys in deaerated sea water
Corrosion of Stainless Steels in Sea Water
When chromium is added to steel, there is a marked increase in corrosion resistance, and
at about 12% chromium, the alloys form a protective passive film and are referred to as
stainless steels. Although the iron-chromium ferritic stainless steels are used commercially,
the greatest tonnage of stainless steels are the austenitic iron-nickel-chromium alloys. These
have better ductility and weldability than the ferritic alloys, and as they usually contain about
18% chromium, they have better corrosion resistance.
In sea water, general attack on these alloys is negligible; however, they are prone to
localised attack due to their high chloride content. This attack is particularly severe in
crevices such as occur with overlapping surfaces, under seals and gaskets, and in similar
areas. Resistance to this type of attack is improved by adding molybdenum to the alloys. The
most commonly used grade of stainless steel in marine environments contains about 17%
chromium, 12% nickel and 2.5% molybdenum and is commonly referred to by its US AISI
designation, Type 316.
Localised attack is stimulated by the difference in oxygen level within the pit or crevice
and that in the surrounding area. In deaerated sea water, where the oxygen level is low, the
risk of localised pitting and crevice corrosion of stainless steels is greatly reduced. Table 3
gives data on some stainless steels in aerated and deaerated sea water. These show that
pitting in deaerated sea water and high chloride-containing brines is much less severe than in
aerated sea water.
Another characteristic of stainless steels is their ability to remain passive even in very
fast flowing sea water. Table 4 gives data on some materials in fast flowing sea water.
Carbon steel and cast iron are rapidly attacked. The copper base alloys suffer erosioncorrosion, but the stainless steel and nickel-base alloys are virtually unattacked.
Table 3. Stainless Steels in Aerated and Deaerated Sea Water and Brine
Alloy
Environment
Velocity
(m/s)
0
0
0
40
40
Max Depth of
Attack (mm)
2.400 P (486 days)
0.170 P (547 days)
0.600 P (547 days)
0.027 G (/year) [8]
0.180 G (/year) [8]
Plenary Lectures
1.32
0.97
<0.01
0.01
Where the alloys are to be welded, the low carbon or stabilised grades (L grades) should
be used as the heat of welding can cause carbide precipitation in the heat affected zone, in
conventional grades.
Although Type 316 stainless steel and its variants, such as Type 316L, represent the
greatest tonnage of stainless steel used in desalination, higher grades, with improved
resistance to pitting and crevice corrosion are available and are used particularly in RO
systems. These alloys have higher molybdenum contents than Type 316, and nitrogen is also
added as this improves resistance to localised attack and is inexpensive. In assessing
resistance to pitting and crevice corrosion, a simple formula relating the chromium,
molybdenum and nitrogen contents is often used:
Pitting resistance equivalent number (PREN) = Cr% + 3.3Mo% + 16N%
(1)
The PREN is useful for ranking the resistance of different stainless steels, and it is
generally accepted that if it exceeds 40 the alloy can be considered resistant to pitting and
crevice corrosion in sea water. Austenitic stainless steels with approximately 20% chromium,
20-25% nickel, 6% molybdenum and 0.2% N (PREN = 43) are now widely used in critical
applications in aerated sea water.
Another important group of stainless steels finding increasing application, are the duplex
alloys. These have a mixed ferrite/austenite structure which provides increased strength.
They normally have higher chromium and lower nickel contents than the austenitics, and
when alloyed with molybdenum and nitrogen, they have similar resistance to pitting and
crevice corrosion. Alloys with about 25% chromium, 7% nickel, 3.5% molybdenum and 0.2%
nitrogen (PREN = 40) have similar resistance to the 6% molybdenum austenitics.
Nickel-base alloys, based on nickel-copper (often referred to as MonelTm alloys) and
nickel chromium, have characteristics similar to the stainless steels in sea water. They are
prone to pitting under static and low flow conditions and become passive in fast flowing sea
water. The nickel copper alloys are used in pumps, particularly for shafts, where their high
corrosion-fatigue strength and good corrosion resistance are advantageous.
Titanium
Titanium has excellent resistance to sea water under static, low and high flow conditions
and does not suffer crevice attack. There are many titanium alloys, but the type used in
desalination is pure titanium containing low levels of iron, oxygen and nitrogen. It is
generally referred to as Grade 2 (ASTM B338 Grade 2). It has good resistance to deaerated
sea water and brine but can suffer crevice corrosion in hot deaerated brine [9]. As a result,
laboratory investigations were carried out to define safe limits for the use of titanium (Fig. 4)
[10].
72
Oldfield
Plenary Lectures
resistant to corrosion by carbon dioxide and are often used in venting systems for this reason.
The solubility of carbon dioxide decreases with increases in temperature, so that for a
given carbon dioxide concentration, the lowest pH levels occur at low temperatures. Figure 5
[16] illustrates this effect for various carbon dioxide partial pressures and temperatures.
Corrosion data on the alloy materials used in desalination are very sparse as vapour
space corrosion has not been studied extensively.
Vapour Side Corrosion due to Halogen Emission
Most desalination plants using sea water are treated with chlorine to control marine
growth in the intake systems. Ideally the chlorination is controlled so that only a low
residual, i.e., 0.1-0.2 ppm, is left at the evaporator, but use of shock dosing and higher than
required injection levels often produce higher levels. When added to sea water, chlorine
reacts with bromides, which are always present, and within a few seconds the chlorine has
been converted to bromine species. As these have a similar antifouling effect to chlorine, in
most cases, this reaction is of no significance. However, the compounds actually present at a
given sea water pH differ. This is illustrated for bromine in Fig. 6 [17] where it can be seen
that bromine gas in solution is present even at pH 7, whereas, as shown in [17], chlorine in
solution is not present above about pH 5. This has important consequences for acid-dosed
plants as the pH is lowered to 4-5 by this treatment and even after decarbonation is still
usually about pH 6. Under these conditions, when deaerated, the bromine gas in solution is
stripped out with other gases and enters the venting system where it can cause severe
corrosion.
74
Oldfield
Plenary Lectures
necessary to use a variety of materials, restricting the more expensive alloys to those areas of
the plant where they are needed. As the cost of alloy materials, such as stainless steels, have
decreased in cost relative to carbon steel and maintenance costs, there has been a tendency for
the industry to make greater use of alloy materials to achieve higher reliability and lower
overall water costs. Thus, factors influencing materials selection are considered for the main
components of MSF units in the following sections.
Heat Exchanger Tubing
A typical MSF unit can be considered in three sections as regards technical requirements
for tubing. These are the reject section, brine heater and recovery section. Table 5 [20]
shows that the failure rates for tubing in these three sections of the plant vary significantly.
Table 5. Failure Rates (Including Tube Replacements)
for All Alloys in Distillation Plants Tubing
Component
Brine Heater
Heat Recovery
Head Reject
Heat Rejection Section. This section handles natural sea water, and copper-base alloys
have often been selected for tubing. The most common cause of failure in these alloys is
impingement attack, which can be caused by partial blockage due to debris passing the
screens, unsatisfactory flow conditions in the water boxes and unsatisfactory entry conditions
to the tube, i.e., any condition that can lead to local turbulence and high velocities (i.e., the
normal design velocity is about 2 m/sec.) Table 2 gives data on the resistance of copper base
alloys to this type of attack, and it is useful to note that the cost of these alloys is on the same
order as their resistance to impingement corrosion.
In unpolluted sea water with good intake screening and flow conditions, the copper base
alloys perform well. However, modifications to the sea water composition by pollutants or
by over-chlorination can give rise to corrosion problems. These are considered below.
Effect of Sulphides. Sulphides may be present in sea water from the decomposition of
organic matter, effluents from nearby sewage works or action of sulphate reducing bacteria
(SRB). Normally when sulphides form in the sea water, there is a reduction in oxygen
content, and in some cases the oxygen is completely removed. In this case, corrosion is not
severe. However, in most cases the sulphides exist in aerated sea water, and this mixture of
sulphides and oxygen, or preexposure to sulphides followed by exposure to aerated sea water,
is very damaging to most copper base alloys. The sulphides enter the protective films and
reduce their resistance so that they are easily damaged by flowing sea water at velocities
which they would normally withstand. Table 6 [21] illustrates this effect on four widely used
heat exchanger alloys. Sulphide levels as low as 20 ppb can be damaging to copper base
alloys.
Although copper base alloys such as cupronickels are not prone to severe pitting or
crevice corrosion in static natural sea water, they can suffer this type of attack if sulphides are
76
Oldfield
present. Where the heat exchanger has operated in clean sea water and has formed good
protective films, these alloys can endure occasional exposure to sulphides. Ferrous sulphate
dosing can also reduce the effects of sulphides [22]. However where sulphides occur
regularly, the use of titanium can often be justified.
Plenary Lectures
form of crevice corrosion, can occur beneath the deposit. Under flowing conditions, sand can
cause damage to the protective films on copper alloys giving rise to impingement attack. In
this context, two factors are important, namely, the sand content and the size of the sand
particles [26]. The cupronickels have better resistance to sand than aluminium brass. The
70/30 cupronickel with 2% iron and 2% manganese was developed specifically for use in
waters with high sand content, e.g., 4000 ppm, and is often specified for reject section tubing.
Titanium has excellent resistance to sand erosion and is used where very high sand content
occurs.
Table 8. Effect of Carbon Steel and Ni Resist Type II on Crevice
Corrosion of Type 316 Stainless Steel in Sea Water
Area Ratio
(SS:C. Steel or Ni Resist)
Crevice Attack
No of Sites Maximum Depth
Initiated
of Attack mm
1:0 (Control)
42
3.18
10:1 (Steel)
0
0.00
50:1 (Steel)
0
0.02
50:1 (Ni-Resist)
0
0.00
30-day test; multicrevice assembly with 120 crevice sites; flow velocity 0.5 m/sec
Heat recovery Section. The data from Table 5 indicate that this section of the plant
presents fewer corrosion problems than others. This is to be expected as in the recovery
section, the sea water and brine are usually deaerated so that there is little oxygen to support a
corrosion reaction. The main corrosion risk is from vapour side corrosion, and as this is more
likely in the first few stages, where carbon dioxide is evolved by the decomposition of
bicarbonates in the sea water, these are normally vented directly to the vacuum system. Also,
the tubing is made from materials with higher resistance to vapour side corrosion, that is to
say, 70/30 cupronickel rather than the 90/10 CuNi alloy or aluminium brass.
When vapour side corrosion occurs, it takes the form of fairly uniform thinning of the
tube wall which eventually perforates. The attack is often concentrated at the tube plates or
tube support junction with the tube and with acidic condensates. This is sometimes reported
as a galvanic effect, for example, when the tube support plates are stainless steel, but it can
occur when these are of the same material as the tubing or are even of carbon steel.
Brine Heater. The data in Table 5 indicate that corrosion conditions in the brine heater
are the most severe in the plant. However, if the causes of these failures are examined [20], it
can be seen that most failures are due to mechanical damage during descaling rather than to
corrosion. The need, therefore, for tubing in this section is for mechanical strength and for
this reason, 70/30 cupronickel is the usual choice, and it is normally used at at 1.2 mm
thickness.
Tube Plates
The main requirements of tube plates are mechanical strength and corrosion resistance.
They should be galvanically compatible with the tube material and preferably slightly anodic
to it so as to give some cathodic protection. As they are much thicker than the tube, some
corrosion can be tolerated provided it does not disturb the tube/tube plate joint which is
78
Oldfield
Plenary Lectures
was the basic cause. Careful attention to air tightness in one affected plant led to a 60%
reduction in the corrosion rate.
As stainless steels have very high corrosion resistance to carbonic acid and low-chloride
distillate, even when oxygen is present, the use of this material for interstage walls and roof
lining can control this type of attack. Stainless steels are often used in these spaces for parts
such as tube support plates, distillate troughs, tube bundle stay bars and vent piping.
However attention to air in-leakage is advised where carbon steel is used.
Demisters
Wire mesh demisters are normally fitted to prevent carryover of droplets of brine.
Because the wire is very thin, usually 0.1-0.2 mm diameter, it is necessary to use materials
with high resistance to general corrosion. Originally the nickel-copper Alloy 400 was widely
used and gave good performance except where sulphides were evolved from the brine. This
alloy is still used but most plants now use Type 316 stainless steel which performs well even
when sulphides are present.
Venting System
Piping and Ejectors. Vacuum on the evaporator is normally produced by steam ejectors
drawing gases from different sections of the plant. The first three stages are normally vented
directly to the system, and gases evolved in lower temperature stages are cascaded to two or
three points before being drawn off into intermediate ejectors and condensers. Where the last
stage is used for deaeration or if a separate deaerator is fitted, the gases are drawn off into the
deaerator condenser. Stainless steels Types 304 or 316 are normally used for the vent piping,
headers within the piping system and baffles within the tube bundles. At lower temperatures
some use has been made of glass-reinforced plastic piping (GRP), but stainless steels are
needed for the higher temperatures, and most plants use them throughout.
The ejectors are also made from stainless steel with nozzles in grades such as Alloy 20.
Provided the chloride content of the gases remains low, the stainless steels work well, the
only risk being from external stress corrosion cracking at temperatures above about 60C. To
minimise this risk, painting of the stainless steel is advised, particularly under insulation
where chlorides can accumulate.
Condensers. Two types of condenser are used in venting systems, namely, shell and
tube type, and barometric. As they have different materials requirements, they are considered
separately.
The shells of shell and tube type condensers are normally made in Type 316L stainless
steel to resist the incondensible gases. In some cases, copper alloys such as aluminium
bronze are used, but this is not common. For tubing, copper base alloys have a limited life
due to vapour side attack in the high concentration of gases drawn from the plant which are
mixed with ammonia from the ejector steam when hydrazine is used in the boilers. As the
attack is usually fairly uniform, several years of life are possible, and some plants use copper
base alloys with regular renewal. However in most cases it is more economic to use a
resistant material and thin wall welded titanium tubing 0.7 mm thick is the usual choice.
High alloy stainless steel such as UNS S31254 has been used successfully for tubing in
ejector condensers in the Middle East. These were roller expanded into an existing naval
80
Oldfield
brass tube plate and were in perfect condition after one year of service [28]. The advantage
of using this alloy is the ease of descaling compared to titanium.
For shell and tube units, tube plates and water boxes require similar considerations as for
the reject section stages. In general copper base alloys are used with anodes in the water
boxes to control galvanic effects when titanium or stainless steel tubes are fitted.
Barometric condensers are essentially vessels into which sea water is sprayed. The large
deaerator condenser can be made from GRP as temperatures are low; however, at higher
temperatures, metals are necessary. Standard stainless steels such as Type 316L are prone to
pitting in the sea water spray. Anodes are sometimes fitted to prevent this, but in a spray
situation, they are not reliable. As the higher temperature units are relatively small, it is
economic to make them from sea water resistant alloys such as the 6% molybdenum stainless
steels.
Sea Water Pumps
Wet pit vertical lift pumps are normally chosen for large MSF units. Pump parts must
withstand fast flowing sea water, and the normal choice for those parts exposed to the most
severe conditions, such as impellers, is stainless steel. The reason for this is evident from the
data in Table 4 where stainless steel Type 316 is seen to passivate in very high velocity sea
water. The nickel copper Alloy 400 behaves similarly. Although stainless steels are
excellent for flow conditions it is also necessary to consider static conditions, and as can be
seen from Table 6, they are then subject to severe pitting. Thus, an all stainless steel pump
would have problems at shutdown. Such problems have been reported [29].
One method of overcoming this is to make the static parts of the pumps of a material
which gives cathodic protection to stainless steels at shutdowns. The material normally
chosen is Ni-Resist, a high alloy cast iron. Table 8 [30] gives data on Ni-Resist and stainless
steel galvanic couples showing that this combination can control pitting and crevice corrosion
under static conditions.
The usual grade of Ni-Resist used is Type D-2W. This has good sea water corrosion
resistance but is subject to stress corrosion cracking in warm sea water and brine. Failures
have occurred in service on castings which have not been stress relieved. However, when
stress relief heat treated for a few hours at 650-675C and furnace cooled the alloy has proven
resistant to cracking. It is essential, therefore, to apply this treatment before service and after
any weld repairs.
In recent years, there has been a trend towards the use of duplex stainless steels in sea
water pumps. These are stronger than the standard austenitic alloys such as Type 316 and the
grades used have higher resistance to pitting and crevice corrosion. In this case, to protect
against pitting at shutdowns, it is advisable to operate the pumps for a short period every few
days.
Brine Recycle and Blowdown Pumps
These are in many ways similar to the sea water pumps described above, but are barreltype or canned pumps. The impeller, shaft and other internals are often made from Type 316
stainless steel or its cast equivalent. The casings are often made of Ni Resist Type D-2W, and
these again need to be stress relieved as cracking, particularly of diffusers, has been
81
Plenary Lectures
experienced in service. The barrels or cans are usually fabricated from clad steels. The
cladding is normally Type 316L stainless steel, but 90/10 cupronickel is also used. In some
cases, thick, 3-5 mm, vulcanised rubber is used.
Distillate Pumps
The distillate leaving the plant is slightly acidic but not strongly corrosive until it
becomes aerated. However, to maintain its purity, it is usual to use stainless steels for the
pumps. Type 316 stainless steel is often used. Although this is not really necessary to handle
low chloride distillate, there is always a risk during hydrotesting that it will be exposed to
high chlorides. If this risk can be eliminated, then stainless steels such as Type 304 or 420
could be used.
SELECTION OF MATERIALS FOR REVERSE OSMOSIS (RO) SYSTEMS
General
RO is a membrane process, and it is important to ensure freedom from corrosion
products and similar material in the feed which might block the membranes. The use of
stainless steels for piping and other components in the plant is, thus, advantageous as these
alloys suffer virtually no general corrosion in waters. The problem is to ensure freedom from
pitting, as most waters contain chlorides, are aerated and depending on their concentration
and the other salts in the water, can cause pitting and crevice corrosion. In the case of sea
water, selection is fairly straightforward and is often based on the PREN as described earlier.
In the case of brackish waters, which can vary greatly as regards the concentration of salts
present and their relative amounts, selection of the optimum grade of stainless steel is more
difficult. Some of the factors involved in the selection of alloys for important components in
RO systems are considered in the following sections.
High Pressure Piping: Sea Water Systems
The high pressure piping consists of large-bore pipes which convey high pressure feed
from the pumps to the membrane banks. The feed is then distributed to rows of membrane
cells by headers with connections to individual cells. A similar arrangement handles the
effluent brine and permeate.
Compression fittings, sometimes incorporating rubber O-rings, are used to connect
various sections of the piping, and these provide sites very favourable to crevice corrosion. It
is necessary, therefore, to use stainless steels with high resistance to crevice corrosion in sea
water. Many plants have used a 6% molybdenum austenitic stainless steel. Nordstrom and
Olsson [31] list 13 plants using this type of alloy.
High Pressure Sea Water Pumps
These pumps operate at about 70 bar pressure, and like the piping, should not add
corrosion products to the feed. The problem is to avoid pitting and crevice corrosion and, as
Ni-Resist is not suitable for these pumps (as its strength is too low), this means that alloys
such as 6% molybdenum austenitics or duplex stainless steels with high PRENs should be
used. However, the main risk of pitting occurs at shutdown, and by ensuring that the pumps
do not stand idle for more than a few days, lower grades can be used. Draining and flushing
with low chloride permeate is needed for longer periods of shutdown.
82
Oldfield
Plenary Lectures
environments: Final report of 16-year exposures, Materials Perform., July 1976, pp. 9-26.
3. H.R. Copson, Effects of velocity on corrosion, Corrosion 16, 1960, pp. 86-92.
4. J.W. Oldfield and B. Todd, Corrosion considerations in selecting metals for flash
chambers, Desalination, 1979, 3, pp. 365-383.
5. F.W. Fink E.L. White and W.K. Boyd, U.S. Department of Interior R&D Progress Report
No. 255, December 1966.
6. D.B. Anderson, Copper-nickel and other alloys for desalination, Inco Publication No.
4319, pp. 39-47.
7. Desalination Materials Manual, Dow Chem for the U.S. Office of Water Research and
Technology, May 1975.
8. G. Pini and J. Weber, Materials for pumping sea water and media with chloride content,
Sultzer Technical Review, 1975, p. 158.
9. S. Kido and T. Shinohara, Corrosion under heat flux encountered in desalination plant,
Desalination, 1977, 22, pp. 369-378.
10. K. Shimogori, H. Sato, F. Kamikubo and T. Fukuzuka, Corrosion resistance of titanium in
MSF desalination plant, Desalination, 1977, 22, pp. 403-413.
11. G.A. Gehring and R.J. Kyle, Galvanic corrosion in steam surface condensers tubed with
either stainless steel or titanium, NACE Corrosion '82, Paper No. 60, 1982.
12. P.D. Simon, Tube sheet corrosion and mitigation techniques in a sea water cooled
titanium-aluminium bronze condenser, NACE Corrosion '83. Paper No. 77, 1983.
13. J.P. Fulford and R.W. Shutz, Characteristics of titanium condenser tube hydriding at two
Florida Power and Light Company plants, ASME/IEEE Power Generating Conference,
Miami Beach, Oct. 1987.
14. T. Fukuzuka, K. Shimogori, H. Sato and F. Kamikubo, Corrosion problems and their
prevention in desalination plant with titanium tube, Proc. of Intl. Congress in Desalination
and Water Re-use, Nice, October 1979, pp. 389-397.
15. P.F. George, J.A. Manning and C.D. Schrieber, Desalination Materials Manual, May
1975.
16. J.W. Oldfield and B. Todd, Vapour side corrosion in MSF plants, Desalination, 1978, 66,
pp. 171-184.
17. J.W. Oldfield and B. Todd, Corrosion problems caused by bromine formation in MSF
desalination plants, Desalination 1981, 38, pp. 233-245.
18. W.S.W Lee, J.W. Oldfield and B. Todd, Corrosion problems caused by bromine
formation in additive dosed MSF plants. Desalination 1983, 44. pp. 209-221.
19. Crevice Corrosion Engineering Guide, Nickel Development Institute, Publication and
Computer Disk D-0003.
20. E.H. Newton, J.D. Birkett and J.M. Ketteringham, Survey of materials in large desalting
plants around the world, A.D. Little & Co., March 1972.
21. R. Francis, The effect of sulphide and chlorine on the corrosion of copper alloy heat
exchanger tubing. BNF Paper R421/5, September 1984.
22. H.P. Hack and T.S. Lee, David Taylor Naval Ship and Research Development Centre
Report DTN SRDC/SME - 81/91, January 1982.
23. R. Francis, The effect of ammonia and chlorine on the corrosion of copper alloy heat
exchanger tubes. BNF paper R241/4, June 1984.
24. S. Sato, Sumitomo Light Metal Industries Review, July 1962.
25. R. Francis, The effect of chlorine additions to cooling water on corrosion of copper alloy
84
Oldfield
85
Plenary Lectures
APPENDIX
Nominal Composition of Alloys
Copper Base Alloys
Alloy
UNS No
Cu
Ni Fe Mn Zn Al Sn Pb Other
(%) (%) (%) (%) (%) (%) (%)
(%)
90\10 Cupronickel
70\30 Cupronickel
66\30\2\2
CuNiFeMn
Aluminium Brass
C70600
C71500
C71640
Rem
Rem
Rem
10
30
30
1.5
1
2
1
1
2
C68700
Rem
22
Admiralty Brass
C44300
Rem
29
Naval Brass
Aluminium Bronze
NiAl Bronze (W)
Admiralty Gunmetal
Leaded Gunmetal
NiAl Bronze (C)
Rem = Remainder
W = Wrought
C = Cast
C46400
C61400
C63000
C90300
C83600
C95800
Rem
Rem
Rem
Rem
Rem
Rem
5
5
2
4
4
1
1.5
1
37
2
5
-
7
10
9
1
10
5
-
5
-
0.04A
s
0.04A
s
Titanium
UNS No Ti (%)
Grade 2
Fe
(%)
R50400
Rem
0.3
Maximum % in all cases
O( %) N( %) H (%) C (%)
0.25
0.03
0.015
0.1
Stainless Steels
a)
Austenitic
Alloy
304
304L
316
316L
317
317L
317LMN
86
UNS No
S30400
S30403
S31600
S31603
S31700
S31703
S31726
C (%)
0.08
0.03
0.08
0.03
0.08
0.03
0.03
Other
0.18N
Oldfield
904L
b)
0.03
UNS No
S31254
N08926
N08367
S31254
C%
0.03
0.03
0.03
0.02
20
25
4.5
1.5Cu
Superaustenitics
Alloy
254SM O
1925 hMO
AL-6XN
HR25 4
c)
N08904
UNS No
S31803
S31500
S32550
S32760
S32750
S32974
Graphite Form
Flake
Spheroidal
Spheroidal
87
into account ionic strength, pH and specific ionic species as relevant factors.
Other relevant efforts include those by Ikeda et al. [9] that look at the
influence ofH2S and O2 on CO2-based corrosion as well as those by Adams
et al. [10]. Many of these efforts suffer from significant drawbacks in that
- They focus on a narrow range of parametric effects, for example, there is
relatively little published information on the effects of H2S in production
systems and how sulfide scaling can affect the CO2 corrosion process,
- Some models focus on just one component of corrosivity, such as erosional
effects, wall shear stress effects or flow effects, and have opted to ignore
effects of chemical species (i.e., factors such as pH, H2S, CO2 etc.), and
- Other models totally rely on laboratory data for predictive modeling, with
the consequence that the simplifying assumptions made in developing
laboratory models often lead to results that can be far removed from what
is observed in the field.
The current model attempts to integrate laboratory data and field
experience within the framework of the relevant controlling parameters that
are most prominent in oil and gas production. It is important to realize that
while arcane theoretical models are interesting from an academic standpoint,
the controlling parameters in a model must also represent data easily available
to oil and gas production personnel. The current model attempts to integrate
principles hitherto delineated in developing the predictive model.
While there have been several studies focusing on the exact mechanism of
metal dissolution in CO2-containing waters, the efforts of de Waard and
Milliams, and others [2,3,9] present a commonly accepted representation
wherein anodic dissolution of iron is a pH dependent mechanism as given by
Bockris [2], and the cathodic process is driven by the direct reduction of
undissociated carbonic acid. These reactions can be represented as [3]
The buildup of the bicarbonate ion can lead to an increase in the pH of the
solution until. Conditions promoting precipitation of iron carbonate are
reached, leading to the reaction given below
arrive at a corrosion rate equation that incorporates the order of the reaction
and an exponential function that approximates for Henry's reaction constant's
temperature dependence. This corrosion rate equation is given as [2]
The corrosion rate obtained by Eq. 4 has typically been seen as the
maximum possible corrosion rate without accounting for iron carbonate
scaling. A nomogram representing Eq. 4 is given in Fig. 1 [2], which also
includes a scale factor to account for the formation of protective carbonate
films that lead to a reduced corrosion rate at higher temperatures.
Lotz et al. [12] have chronicled the role of the hydrocarbon condensate
in providing corrosion mitigation in specific production systems. The role of
the type of oil or gas condensate is important from the standpoint of accurate
assessment as reported by Choi et al. and Efird [13,14]. Other studies
evaluating effects of critical parameters such as pH and velocity on CO2
corrosion include those by Dugstad and Lunde [15] as well as Lotz [16].
Other predictive models also include those by Gunatlun [17] and Bonis and
Crolet [18] wherein a combination of the parameters discussed herein along
with electrochemical considerations have been utilized to arrive at a
determination of the corrosion rate.
The primary objective of the corrosivity prediction model described in
this paper is to address the need of developing a predictive method that
would synthesize different parametric relationships based on information
from literature, laboratory research/data and practical experience/expertise.
It has often been observed that laboratory data and the ensuing models
represent poor and often inadequate simulation of field conditions [19]. It is
also necessary to understand that field data is typically sparse and can be
negated by other production data. The need to integrate field data/experience
and laboratory models stems from the fact that the laboratory data can
provide significant pointers and trends that can be used in conjunction with
field data and experience. The idea is to develop a methodology that can
integrate analytical and heuristic models. To this end, this predictive system
mirrors other successful development efforts undertaken by the authors in
the areas of evaluation of CRAs and cracking in steels [20,21]. The central
theme is to develop a computer program that can bring together different
types of modeling knowledge to provide a realistic solution to the significant
question of predicting corrosion rates in typical production environments.
CORROSIVITY PREDICTION MODEL DESCRIPTION
A flowchart delineating the hierarchical reasoning structure of the
predictive model is given in Fig. 2. The first step in corrosivity
determination is computation of the system pH, since it is the hydrogen ion
concentration that drives the anodic dissolution. Further, the role of pH in
promoting or mitigating CO2-based corrosion has been extensively
chronicled [19,22]. For production environments, where it is the dissolved
CO2 or H2S that contributes significantly to a suppressed pH, the pH can be
determined as a function of acid gas partial pressures, bicarbonates and
Where Cl and C2 are constants, pH2S and pCO2 are partial pressures in bar
and the HCO3 concentration is represented in meq/l (61 mg/l).
The system pH is given by the larger number between PHI and pH2.
Correspondingly, if the temperature is higher than 100C, there is a slight
reduction in the hydrogen ion concentration as shown in Fig. 3, but the
change in pH can be accounted for by a change in the value of the constants
in Eq. 5 and 6 above. Once the system pH is determined, the effective CO2
partial pressure can be determined from Eq. 5 as,
for the effect of other critical variables in the system. Further, this rate does
not indicate modality (general or localized), but rather, represents the
maximum rate of attack.
As mentioned earlier, it is necessary to superposition the effects of
other critical system parameters. The flowchart in Fig. 2 provides a list of
the sequential effects that are important from a standpoint of corrosivity
determination. In addition to the system pH, these include:
H2S partial pressure, maximum operating temperature, dissolved chlorides,
gas-to-oil ratio, water-to-gas ratio/water cut, oil type and its persistence,
elemental sulfur/aeration, fluid velocity, type of flow, and inhibition type
and efficiency.
H2S
Oilfield production environments, in recent years, have been
characterized by an increasing presence ofH2S and related corrosion
considerations. Even though H2S is probably the most significant concern in
current-day corrosion and cracking evaluation, the role ofH2S in corrosion
in steels has received much less attention when compared to the widely
studied CO2 corrosion. [26]. However, H2S-related corrosion and cracking
has remained one of the biggest concerns for operators involved in
production because of the significance of H2Srelated damage [27].
In the current modeling effort, in addition to the contribution in pH
reduction, H2S has a threefold role:
- At very low levels of H2S 0.01 psia), CO2 is the dominant corrosive
species, and at temperatures above 60C, corrosion and any passivity is a
function of F eC03 formation-related phenomenon, and the presence of
H2S has no realistic significance.
- In CO2 dominated systems [26,28], the presence of even small amounts
of H2S (ratio of pC02/pH2S > 200), can lead to the formation of an iron
sulfide scale called mackinawite at temperatures below 120C. However,
this particular form of scaling, which is produced on the metal surface
directly as a function of a reaction between Fe++ and S ., is influenced
by pH and temperature [27]. This surface reaction can lead to the
formation of a thin surface film that can mitigate corrosion. The authors
are currently pursuing laboratory studies to characterize the stability and
formation of mackinawite in sour systems.
Temperature
Temperature has a significant impact on corrosivity in CO~2S systems.
Corrosion rate as a function of different levels of CO2 and temperature is
given in Fig. 7 [2]. It has to be noted that once the corrosion products are
formed, there is a significant mitigation in corrosivity. It is also apparent that
the carbonate film is more stable at higher temperatures and affords greater
protection at higher temperatures. Figure 7 also shows that at temperatures
beyond 120C, the corrosion rate is almost independent of the CO2 partial
pressure of the system. The carbonate film may, however, be weakened by
high chloride concentrations, or it can be broken by high velocity. In H2Sdominated systems, because no carbonate scale may be formed and the FeS
film becomes porous and unstable at temperatures beyond 120C, significant
localized corrosion may be observed.
Chlorides
Produced water from hydrocarbon formations typically contains
varying amounts of chloride salts dissolved in solution. The chloride
concentration in this water can vary considerably, from zero or a few parts
per million in condensed water to saturation in formation waters having high
total dissolved salts/solids (TDS). In naturally deaerated production
environments, the corrosion rate increases with increasing chloride ion
content over the range 10,000 ppm to 100,000 ppm [30]. The magnitude of
this effect increases with increasing temperature over 60C (1 50F). This
combined effect results from the fact that chloride ions in solution can be
incorporated into and penetrate surface corrosion films, which can lead to
determines the flow behavior and flow regime. In general terms, this is
manifested as static conditions (i.e., little or no flow) at low velocities,
stratified flow at intermediate conditions, and turbulent flow at higher flow
rates. One measure which can be used to define the flow conditions is the
superficial gas velocity. In liquid (i.e., oil / water) systems, this is replaced
with the liquid velocity.
Velocities less than 1 m/s are considered static. Under these conditions
corrosion rates can be higher than those observed under moderate flow
conditions. This occurs because under static conditions, there is no natural
turbulence to assist the mixing and dispersion of protective liquid
hydrocarbons or inhibitor species in the aqueous phase. Additionally,
corrosion products and other deposits can settle out of the liquid phase to
promote crevice attack and underdeposit corrosion.
At velocities between 1 and 3 m/sec, stratified conditions generally still
exist. However, the increased flow promotes a sweeping away of some
deposits, and increasing agitation and mixing. At 5 m/sec flow velocity,
corrosion rates in uninhibited applications start to increase rapidly with
increasing velocity [31]. The data shown in Fig. 9 [31] demonstrate the
effects of velocity on corrosion rate for both inhibited and non-inhibited
systems. For inhibited applications, corrosion rates of steel increase only
slightly at velocities between 3 and 10 m/sec, as a result of mixing of the
hydrocarbon and aqueous phases. At velocities above about 10 m/sec,
corrosion rates in inhibited systems start to increase due to the removal of
protective surface films by the high-velocity flow.
Flow-related effects on corrosivity have been linked to the wall shear stress
developed and is an area of intense research in the community [32]. Flowinduced corrosion is a direct consequence of mass and momentum transfer
effects in a dynamic flow system where the interplay of inertial and viscous
forces is responsible for accelerating or decelerating metal loss at the
fluid/metal interface. While flow-induced corrosion is a significant
component of predictive modeling discussed herein, the topic of flow-related
effects is being actively researched by the authors and forms the focus of
another publication. Another relevant aspect of flow- or velocity-induced
corrosion is erosion-corrosion [33] and refers to the mechanical removal of
corrosion product films through momentum effects or through impingement
and abrasion. Guidelines for velocity limits with respect to erosional
considerations are given in API-14E in terms of the density of the fluid
medium [34].
Water/Gas/Oil Ratios
The predictive model classifies systems as oil dominated or gas dominated
on the basis of the gas/oil ratio (GOR) of the production environment. If the
environment has a GOR < 890
m3/m3 (5000 scf/bbl in English units) [35], the tendency for corrosion and
environmental cracking is often substantially reduced. This is caused by the
possibly inhibiting effect of the oil film on the metal surface, which
effectively reduces the corrosivity of the environment. However, the
inhibiting effect is dependent on the oil phase being persistent and acting as
a barrier between the metal and the corrosive environment. The persistence
of the oil phase is a strong factor in providing protection, even in systems
with high water cuts. In oil systems with a persistent oil phase and up to
45% water cut, corrosion is fully suppressed, irrespective of the type of
hydrocarbon [12]. Relative wet ability of the oil phase versus the water
phase has a significant effect on corrosion [36]. Metal surfaces that are oil
wet show significantly lower corrosion rates [37].
The predictive model described in this paper provides for a significant
reduction in the corrosion rate (up to a factor of 4) based on the type of oil
phase, i.e., persistent, mildly persistent and not persistent. However, the
degree of protection can be quantified only as a function of water cut and
velocity. The persistence determination is a more complex task and requires
knowledge of the kerogen type and hydrocarbon density. It is important to
understand the type of crude oil in terms of the organic compounds that
make up the crude to determine wettability effects. Figure 10 shows data that
relate the acid number of the crude to oil wettability, and Fig. 11 shows
corrosion rate as a function of produced water content for different crude
oil/produced water mixtures [36]. While the effect of persistence of the oil
medium is significant on corrosion rates, it is even more difficult to quantify
precise compositional elements of oil medium that contribute to wettability
and persistent oil film formation. Such quantification is possible by rigorous
laboratory testing of different actual, uncontaminated (read "deaerated")
production water samples, so as to determine the extent of protection.
In oil systems, the water cut acts in synergy with the oil phase to
determine the level of protection from the hydrocarbon phase. However, at
very low water cuts 5%), the corrosive severity of the environment is
lessened due to the absence of adequate aqueous medium to promote the
corrosion reaction.
In gas-dominated systems, there are two measures to evaluate the
availability of the aqueous medium. If the operating temperature is higher
than the dew point of the environment, no condensation is going to be
possible, leading to highly reduced corrosion rates. Corrosion under
condensing conditions (i.e., operating temperature less than the dew point) is
a function of the rate of condensation and transport of corrosion products
from the metal surface [38]. If the total water in a condensing system as
measured by the water-to-gas ratio is < 11.3 m3/Mm3 (2 bbl water/MSCF
gas), corrosivity is substantially reduced.
Aeration/Sulfur
The presence of oxygen significantly alters the corrosivity of the
environment in production systems. Old field and Todd [39] chronicled how
the presence of oxygen could significantly increase corrosion rates due to
acceleration of anodic oxidation. While the corrosion rate increases with
oxygen, the rate of oxygen reduction as a catholic reaction is further
exacerbated by
- Increased operating temperature,
- Increased fluid flow leading to increased mass flow of oxygen to the
metal surface, and
- Increased oxygen concentration
Data showing increases in corrosion rate as a function of oxygen
concentration for differing temperatures are shown in Fig. 12 [39]. The
presence of elemental sulfur is similar to that of free oxygen since elemental
sulfur also acts as a strong oxidizing agent.
Inhibition/Inhibition Effectiveness
Appropriate inhibition is a critical criterion for effective use of carbon steels
in corrosive production systems. Inhibition has been typically found to be
viable in flows with velocity in the range of 0.3-10 mfs. Requirements for
the type of inhibitor and the method of delivery depend on the type of
system (Le., production tubing or horizontal flow lines) to be inhibited.
Inhibition efficiency (IE) describes the efficacy of an inhibitor treatment in
Inhibitor concentration,
Severity of the corrosive environment,
Service temperature,
Solubility of the inhibitor in the aqueous phase,
Phase behavior of the inhibitor and carrier fluid in the service
environment, and Persistence of the inhibitor on the metal surface.
flow models that capture the effects of inertial and viscous forces in single
phase and multi-phase flows. Wall shear stress developed as a function of
prevalent flow regimes has a direct influence on corrosion rate and is the
focus of considerable research in both industry and academia [32,40].
The metallurgy of steels used -m CO:z/H2S production environments is
critical to determining environmental corrosivity.Metallurgical factors
include microstructure, material processing (e.g., annealed, quenched and
tempered, normalized etc.) and other morphology-related factors like
hardness of welds and residual stresses. The addition of residual and
alloying elements (e.g., Cr, Cu, Ni, etc.) has been shown to have a
significant impact on corrosion performance [41,42]. While there is some
data available for understanding the effects of metallurgy on corrosivity in
CO2 environments, very little information is available on metallurgical
effects versus corrosivity in H2S environments, and this represents an area
of active research. The authors have currently initiated a research program
on testing to quantify metallurgical effects as they relate to corrosion in
typical production environments [43].
CONCLUSIONS
Predicting the corroslV1ty of CO:z/H2S production environments is a
complex and challenging task requiring a clear understanding of the role of
several critical parameters from theoretical and practical standpoints. While
theoretical models are valuable from a perspective of mechanistic
comprehension, it is necessary to integrate different kinds of data knowledge
and experience-based expertise to provide a realistic basis for corrosion
prediction. A hierarchical predictive model has been developed to integrate
the effects and interactions of several critical parameters enrooted to
determining system corrosivity. The model has been implemented as a
Widows-based computer program and incorporates a framework that
facilitates further refinement.
The authors would like to recognize and thank the contributions of
researchers and pioneers in corrosion modeling, whose efforts, available in
the public domain, provided the firmament on which the model presented in
this paper has been built. The authors also acknowledge the contributions of
numerous workers within the authors' organization whose untiring efforts
have contributed significantly to the development of the corrosivity model.
REFERENCES
- C.S. Fang et al., Computer model of a gas condensate well containing
carbon dioxide, Corrosion/89, Paper No. 465, New Orleans, Louisiana,
USA, 1989.
- C. de Waard and U. Lotz, Prediction of CO2 corrosion of carbon steel,
Corrosion/93, Paper No. 69, New Orleans, Louisiana, USA, 1993.
- C. de Waard and D.E. Milliams, Carbonic acid corrosion of steel,
Corrosion 31,5, 1975, p.I77.
- E. Dayalan et al., Modeling CO2 corrosion of carbon steels in pipe flow,
Corrosion/95, Paper No. 118, Orlando, Florida, USA, 1995.
- lD. Garber et al., Down hole parameters to predict mist flow and tubing
life in gas condensate wells, Corrosion/94, Paper No. 25, Baltimore,
Maryland, USA, 1994.
- RD. Kane and S. Srinivasan, Proceedings of CLI Workshop on Oil and
Gas Corrosivity, Abu Dhabi United Arab Emirates, April 1995.
- L.H. Gatzky and RH. Hausler, A novel correlation of tubing corrosion
rates and gas production rates, Advances in CO2 Corrosion, Vol. 1,
NACE, 1984, p. 87.
- lL Crolet and M Bonis, A tentative method for predicting the corrosivity
of wells in new CO2 fields, Advances in CO2 Corrosion, Vol. 2, NACE,
1985, p. 23.
- A Ikeda et al., Influence of environmental factors on corrosion in CO2
wells, Advances in CO2 Corrosion, Vol. 2, NACE 1985, pp. 1-22.
- C.D. Adams et al., Methods of prediction of tubing life for gas
condensate wells containing CO2, 23rd OTC, Houston, Texas, USA,
1991.
- K. Videm and l Kvarekval, Corrosion of carbon steel in C02 saturated
aqueous solutions containing small amounts ofH2S, Corrosion/94, Paper
No. 12, 1994.
- U. Lotz. et al., The effect of oil or gas condensate on carbonic acid
corrosion, Corrosion/90, Paper No. 41,1990.
- H. l Choi et al., Corrosion rate measurements of L-80 grade down hole
tubular in flowing brines, Corrosion/88, Paper No. 213, St. Louis, MissoUSA, 1988.
- KD. Efird, Predicting corrosion of steel in crude oil production, Materials
Performance 30, 3, March 1991, pp. 63-66.
- A Dugstad and L. Lunde, Parametric study of CO2 corrosion of carbon
steel, Corrosion/94, Paper No. 14, 1994.
ABSTRACT
There are huge drilling operations in most areas of the Kingdom of Saudi Arabia nowadays
searching for potential hydrocarbon reservoirs. The increasing expense of importing drilling fluid
components for oil and gas wells, drilling, especially clays, necessitates the testing of some local clays
which are less expensive and are abundantly available. Therefore, representative Tabuk formation clay
samples from the northern and central provinces of Saudi Arabia have been studied. The clays were
mineralogically investigated using x-ray diffraction and scanning electron microscopy. The
physicochemical properties of clay suspensions with and without common drilling fluid additives were
measured. These properties include rheology, filtration loss, density and pH. The thermal stability of
clay minerals and suspensions was studied. Since sample 2 of the Tabuk clay produced better results,
its thermal stability was further studied by autoclaving its suspensions at temperatures between 25 and
121oC after the addition of high-viscosity carboxy methyl cellulose (HV-CMC) and XC-polymer. A
concentration of 10% by weight of sample 2 of the Tabuk formation clay plus 1% NaOH and 0.5 XCpolymer produced the best rheological, filtration and thermal stability.
Corrosion in drilling operations is strongly related to the composition of drilling fluids. A
concentration of 10% by weight of sample 2 of the Tabuk formation clay plus 0.5% NaOH and 0.5
XC-polymer developed minimum corrosion rates as revealed by corrosivity tests (static and dynamic)
and surface morphology investigations
Key Words: Corrosivity, drilling fluids, thermal stability, rheology, Tabuk formation, clays
INTRODUCTION
Clays in Saudi Arabia are represented by numerous commercial stocks [1-2]. The
mineralogical, chemical and mechanical analysis of these clays led to their use in different
industrial applications. The use of these national clays in the drilling of oil, gas or water
wells in the Kingdom as well in other Arabian Gulf countries will save millions of dollars that
otherwise would be spent on purchasing these materials. In the Khurays and Qasim regions,
many kinds of clays are found and can be studied [3]. Other unexplored areas for commercial
utilization of clay and shale are abundant in the northern region of the Kingdom, especially in
111
the Tabuk formation. The clay deposits of AsSarat in the southern region of the Kingdom
represent another possible source of clay minerals [4]. The geological studies of the Ummer
Radhuma and Dammam formations have indicated the presence of numerous types of clay
minerals, especially palygorskite, in these formations [5,6,7]. In Saudi Arabia, the utilization
of clays, especially in the drilling of oil and water wells, has been very limited. The intense
exploration for oil and water in the Kingdom as well as other Gulf countries, necessitates the
use of local raw materials in this important industry [8].
EXPERIMENTAL PROCEDURE
This study specifically aims to achieve the following objectives:
112
Al-Awad et al.
113
Sieve Size
(mm)
500
300
150
100
63
40
Fines
114
Weight (%)
Sample 1
0
0.2
0.3
0.3
1.6
2.6
95
Weight (%)
Sample 2
0
0
0
0
0.3
0.5
99.2
Al-Awad et al.
Figure 3. X-ray diffractogram of Tabuk formation clays, raw samples 1 and 2, at 25oC
(a) Sample 1
115
(b) Sample 2
Figure 4. Scanning electron micrographs of Tabuk formation clays
Al-Awad et al.
even with concentrations of clay solids below 10%. Table 2 gives the typical relationships of
plastic and the apparent viscosities, yield point and density of Tabuk formation clays
suspensions in freshwater. Such rheological behavior is typical for clay-water systems
formed using illite and kaolinite clays. The filtration loss was too high for it to be used as a
drilling fluid without using fluid loss control additives. In order to obtain a drilling fluid
exhibiting minimum corrosion rates, NaOH was added, and concentrations of 0.5 to 1.0% by
weight, were found adequate to develop the desired properties. 0.5 percent XC-Polymer by
weight was added to improve the fluid rheology and filtration loss. Figure 8 shows the
reheograms of the drilling fluids prepared from 10% by weight Tabuk formation clay
(sample 2) plus 1.0% NaOH with the addition of various additives; the filtration behavior of
the best additives are shown in Fig. 9. Figure 10 shows a comparison between the drilling
fluid formulated from Tabuk formation clay suspension (10% Tabuk formation clay sample 2,
0.5% XC-polymer, and 1% NaOH) with common drilling clays.
117
Figure 6. Shear stress-shear rate relationships for Tabuk formation clay (sample 1)
suspension using freshwater
Figure 7.
118
Al-Awad et al.
Figure 8. Shear stress-shear rate relationships for 15% Tabuk clay (sample 2) suspension
with various additives
Figure 9. API and HT-HP filteration loss of 10% by weight of Tabuk formation clay (sample
2) suspension in freshwater
Figure 10. Natural and conditioned (10% Tabuk clay + 0.5% XC-polymer + 1% NaOH) clay
119
10
15
20
Density
Yield Point
Apparent Viscosity
Plastic Viscosity
(ppg)
Sample Sample
1
2
8.9
8.9
9.3
9.1
9.7
9.4
(lb/100 ft2)
Sample Sample
1
2
4.5
3.0
5.0
4.0
7.5
6.3
(cp)
Sample Sample
1
2
2.94
2.94
3.74
3.74
5.27
5.27
(cp)
Sample Sample
1
2
1.1
1.1
2.14
2.14
2.15
2.15
Corrosivity
Corrosion is noted for its destructive effect on materials, and its consequences on the
economy. Corrosion has been a problem in the petroleum industry throughout its history.
Drilling fluid components play major roles in corrosion processes. To understand the
influence of drilling fluids on the rate of corrosion, certain factors should be studied, such as
their physical and chemical properties. Corrosion within a drilling well was simulated by
immersing test specimens in the drilling fluid at a fixed exposure time and temperature in
both static and dynamic conditions. The loss in weight of the test specimen served to
measure the rate of corrosion. Drilling fluids formulated from Tabuk formation clays (sample
2) were investigated for their corrosivity on three different types of casing alloys, namely:
mild steel, J-55 casing grade and K-55 casing grade. 10% by weight suspension of Tabuk
formation clay (sample 2) was chosen to study the corrosivity of Tabuk formation clays with
and without the addition of NaOH. Coupons made from the chosen alloys were made and
appropriately placed inside either the static cell or the dynamic loop, depending on the type of
test to be performed. Then the formulated drilling fluid was added to the test apparatus. Both
tests were run for two week periods at 58oC. After termination of the test, the samples were
cleaned with inert fluid, and their weights were recorded and their surfaces were carefully
examined using a low-power microscope. The following formula was used to calculate the
corrosion rate [11].
WL
mpy = 22273
DAT
where
mpy
W
D
A
T
120
(1)
Al-Awad et al.
where mpy is the penetration (corrosion) rate in mm/year. As shown in Table 3, mild steel
had corrosion rates under dynamic conditions that were two-fold greater than in static
conditions. This can be attributed to the effect of shear forces on the surface of the metal
caused by the
121
Figure 11. Surface morphology of steel coupons tested under static conditions for 2 weeks
using a drilling fluid formulated from 10% Tabuk formation clay (sample 2) +
0.5% XC-polymer with and without the addition of NaOH
122
Al-Awad et al.
Figure 12. Surface morphology of steel coupons tested under dynamic conditions for 2 weeks
using a drilling fluid formulated from 10% Tabuk formation clay (sample 2) +
0.5% XC-polymer with and without the addition of NaOH
123
flow of the test fluid. Mild steel was found to have the lowest resistance to corrosion by
activated Tabuk formation clays, while K-55 had the highest resistance to corrosion under the
same test conditions. In the static tests, all three samples corroded at the same rate. The
corrosion rates were significantly reduced when NaOH was added to the test fluids. This was
due to the ability of NaOH to change the test fluids environment from being acidic (pH = 5)
to being alkaline (pH = 11), as shown in Table 3. The surface morphology of the tested steels
before and after the addition of NaOH for both static and dynamic tests is shown in Figs. 11
and 12. It is clear from the figures that the metal surfaces were more severely corroded
before the addition of NaOH.
Table 3. Corrosion Tests Results of Tabuk Formation Clays
Test
Coupon
Static Test
(mpy)
Dynamic Test
(mpy)
A
B
C
D
Mild Steel
0.26
0.10
1.7
0.255
K-55
0.25
0.10
1.0
0.212
J-55
0.23
0.10
0.8
0.189
A: Static test (10% sample 2 without additives, pH = 5)
B: Static test (10% sample 2 + 0.5% XC-polymer + 0.5% NaOH, pH = 11)
C: Dynamic test (10% sample 2 without additives, pH = 5)
D: Dynamic (10% Sample 2 + 0.5% XC-polymer + 0.5% NaOH, pH = 11)
CONCLUSIONS
1. The tested clays made from Tabuk formation clays contain more than 95% fines by
weight (< 40 mm). They are exclusively composed of the clay minerals illite and
kaolinite together with small amounts of interstratified minerals and quartz.
2. The rheological properties of the Tabuk formation clay suspensions indicate that they lie
in the range of typical native clays. After the addition of common drilling fluid additives,
the suspensions had more or less the same flow behavior as commercial clays. Therefore,
it is recommended that this clay be used in formulating low-weight drilling fluids.
3. The formulated drilling fluids made from Tabuk formation clay (sample 2) are thermally
stable up to the tested temperatures of 25-121oC.
4. Corrosion tests on the drilling fluids formulated from Tabuk formation clays (sample 2)
indicated that the fluids possessed minimal corrosivity.
5. The application of Tabuk formation clays in oil well drilling is recommended especially
after performing economical feasibility studies.
REFERENCES
1. A.S. Dahab, Evaluation of some Saudi shales for use in drilling fluids, First Conference
on Indigenous Raw Materials and Their Industrial Utilization in the Gulf Region, Kuwait,
November 1-4, 1986.
2. M.M. Aba-Husayn and A.H. Sayegh, Mineralogy of Al-Hasa desert soils, Saudi Arabia,
124
Al-Awad et al.
125
Texaco E & P
P.O. Box 8992, Corpus Christi, TX 78468, USA
3
ABSTRACT
Scale deposits are a concern for oil producers not only throughout the United States and United
Kingdom (North Sea) but also within parts of the Middle East, primarily in Egypt and the Arabian
Gulf region. In addition to plugging perforations and reducing production volumes, certain types of
sulfate scale deposits are becoming an environmental issue.
Considering the varied problems often associated with the chemical and mechanical removal and
disposal of sulfate scale deposits, the best, most cost-effective method for dealing with sulfate scale is
simply to try to find a way to prevent the scale deposits from occurring in the first place. In order to
achieve this goal, an effective sulfate scale inhibition program must be developed.
As part of its efforts in this area, Texaco has actively participated in a research consortium which is
developing new technology specifically aimed at preventing the deposition of barium sulfate scales in oil
field production facilities. Barium sulfate is a particularly troublesome form of scale due, in part, to its
extreme insolubility. Removing barium sulfate with chemical scale dissolvers is often a very difficult
process. This paper will present the results of a recent case history in which Texaco is currently applying
scale control technology with notable success. Specifically, the process of screening and selecting a scale
inhibitor suited to the temperature, mineralogy, and brine chemistry of the producing formation will be
described. The design and implementation of the scale squeeze treatment will then be discussed. This
technology can also be applied in preventing other sulfate-type scales and for inhibiting calcium carbonate
scale as well.
Key Words: Scale inhibition, barium sulfate, scale inhibitors, squeeze treatment, scaling
tendency, scale prediction, laboratory testing, NORM
127
INTRODUCTION
The A.E. Guerra No. 43 well, located in South Texas, produces 8.5 MMSCFPD, 50
BOPD, and 120 BWPD. The reservoir is relatively deep (approximately 14,000 ft). The
bottom hole temperature is typically about 340F, and the reservoir pressure is approximately
6997 psi. The reservoir formation is composed of calcite (20 - 40%), quartz (25 - 30%),
feldspar (20%), and clay minerals (10 - 35%). Among the clay minerals, illite is typically
80% and chlorite is around 20%. The porosity is about 18%. The permeability varies from
0.01 to 0.05 mDarcy, and it is a fracture-stimulated reservoir. The content of carbon dioxide
in the gas phase is about 0.5%.
Two months after production commenced, scale buildup was discovered when a tubing
caliper survey was run. Shortly thereafter, gas production dropped from 10 MMSCFPD to 5
MMSCFPD. Two types of water-formed scale deposits, barium sulfate and calcium
carbonate, were encountered in the production system (mainly in the downhole tubing). Hard
deposits of barium sulfate scale pose a severe operational problem to production operations
since they cannot be easily removed once deposited and have occasionally been associated
with naturally occurring radioactive materials (NORM) [1]. In this case, fortunately, the
barium sulfate scale was not contaminated with NORM.
Before the squeeze treatment, discussed in this paper, barium sulfate and calcium
carbonate scales had to be periodically removed by chipping or broaching with wire-line
tools. This operation is expensive, time-consuming, and risky considering the possibility of
losing the tools in the well. The annual cost for the frequent mechanical removal of the scale
deposits was estimated to have been US $87,000.
Under the sponsorship of the Gas Research Institute (GRI), the Brine Chemistry
Consortium at Rice University and Water Research Institute conducted an integrated study of
the scaling condition in the subject well and designed a treatment plan to control barium
sulfate scaling. This paper summarizes the laboratory design and field implementation of a
scale inhibitor squeeze treatment. First, a brine analysis and scaling tendency are described.
Next, laboratory tests of scale inhibitors are presented. Finally, the field squeeze treatment is
detailed and the results are shown.
BRINE CHEMISTRY AND SCALING TENDENCY
Brine samples were taken at the wellhead and analyzed in the laboratory. The chemical
composition of the brine and other information concerning the well are listed in Table 1. The
chemical analysis was performed at room temperature and pressure. The concentration of
each cation was analyzed using inductively coupled plasma spectrometry.The chloride
concentration and bicarbonate alkalinity were determined by titration. The concentration of
sulfate was determined by a turbidimetric method and found to be very small (< 5 mg/1).
The scaling tendency of the brine, expressed as a saturation index (SI), was calculated
under various production conditions using the EQPITZER program [2]. EQPITZER is a
computer program for calculating the SI of brines with respect to common water-formed scale
deposits such as calcite, gypsum, anhydrite, celestite, and barite. The SI for a sparingly
soluble salt, M+A-, is defined as the logarithm of the ratio of the ionic activity product divided
by the thermodynamic solubility product:
SI = log[(aM+ aA-)/Ksp]
(1)
128
Hinrichsen et al.
An SI > 0 indicates a supersaturated solution and, hence, a probability for scale deposition.
No scale is anticipated, however, when the calculated SI < 0 (i.e., the brine is
undersaturated).
Table 1. Chemical Composition of the A.E. Guerra Brine
Species
+
Na
Mg2+
Ca 2+
Sr2+
Ba2+
Fe (total)
ClSO42Alkalinity (HCO3-)
Ionic Strength (M)
pH (meas.) at surface
CO2(g) in the gas phase
Concentration
(mg/1)
19871.8
54.0
6500.0
700.0
550.0
12.0
43000.0
<5.0
281.0
(mmol/l)
864.4
2.2
162.2
8.0
4.0
0.2
1228.6
<0.052
4.6
1.42
7.10
0.5%
The calculated saturation indices are presented in Table 2. It can be concluded that a
serious calcium carbonate scaling potential will develop (the SI is greater than 1.0) as the
reservoir pressure drops. This is verified by the occurrence of calcium carbonate scale in the
tubing near the perforations where there is a significant pressure reduction.
Table 2. Calculated Saturation Index (SI) for the A.E. Guerra Brine
with Respect to Common Water-Formed Scale Deposits
Parameters
Temperature (F)
Pressure (psi)
pH (calc)
SI (calcite)
SI (barite)
SI (celestite)
SI (anhydrite)
Downhole
236
6997
5.34
-0.27
-0.23
-1.60
-2.05
Wellhead
236
397
6.71
1.21
0.01
-1.37
-1.75
Surface
236
14.7
7.94
2.24
0.03
-1.35
-1.72
77
14.7
7.91
1.94
1.17
-1.70
-2.70
only occur when the temperature is reduced to 77F (SI = 1.17). The discrepancy between
the calculated SI and field observations could be due to the fact that the original brine
analysis may have incorrectly reflected the true downhole concentrations of barium and
sulfate.
INHIBITOR EVALUATION AND SQUEEZE SIMULATION
In view of the declining gas production rate and the potential for further scale deposition,
it was decided to treat the subject gas well by a scale squeeze treatment. Given the US $4
MM cost to drill and complete the well and the additional US $1.5 MM cost for the fracture
operation, a carefully planned series of laboratory tests was conducted to ensure not only that
the scale squeeze treatment would be effective but also that the chemical treatment would not
contribute to any formation damage.
Several commercially available scale inhibitors were tested in the laboratory for their
efficiency at preventing barium sulfate scale deposition. Both static and dynamic tests were
conducted.
The static testing of inhibitor efficiency was based on the measurement of the nucleation
induction period for barium sulfate in the presence of inhibitors [3], specifically, the relative
prolongation of the nucleation induction period in the presence of various scale inhibitors,
each at the same concentration. The static test results were then used to rank the scale
inhibitors according to their efficiency in delaying the nucleation process.
The dynamic testing of scale-inhibitor effectiveness was performed in the laboratory
using a high-temperature and high-pressure flow-through apparatus which is designed to
simulate a production system [4]. The dynamic test results are useful in ranking the scale
inhibitors based upon the minimum effective dose for each inhibitor (The minimum effective
dose is the minimum concentration required to prevent any scale deposition).
Several common commercial scale inhibitors were tested. These inhibitors include 1hydroxyethylidene-1,1-diphosphonic acid (HEDP), nitrilotrimethylene phosphonic acid
(NTMP), hexamethylene diamine tetramethylene phosphonic acid (HDTMP), diethylene
triamine pentamethylene phosphonic acid (DTPMP), bis-hexamethylene triamine
tetramethylene phosphonic acid (BHTMP), polyacrylates (PAA, molecular weight from 1000
to 7000), phosphinopolycarboxylates (PPPC, molecular weight from 1900 to 3800), and
sulfonated polyacrylic acid (SPA, molecular weight of 3500). Based on the static and
dynamic test data, BHTMP was found to be effective and superior to other scale inhibitors,
and was recommended for squeeze-treatment use.
Once the scale inhibitor testing was complete, a simulation of the squeeze process was
conducted in the laboratory in order to obtain information concerning the retention and
release of the BHTMP inhibitor onto and off of the A.E. Guerra core material. First, the
BHTMP inhibitor solution was pumped into a column packed with synthetic materials having
a mineralogical composition similar to the formation rock. The column was then shut in for
two days. Next, the column was turned around and a synthetic brine was pumped through the
packed column from the opposite direction. These two steps are designed to simulate the
inhibitor injection and subsequent return flow. The concentration of BHTMP in the return
flow was continuously monitored for over 60 pore volumes. The flow rate was 10 ml/min.
The inhibitor return data is presented in Fig. 1.
130
Hinrichsen et al.
a
100000
0.5%
5%
10000
100
10
1
0
20
40
60
80
100
Pore Volumes
20
10
0.5 %
5%
0
0
20
40
60
80
100
Pore Volumes
131
Two sets of simulations were performed using two different injection concentrations (5%
and 0.5% BHTMP). The inhibitor concentration remained over 1 mg/l for over 100 pore
volumes (Fig. 1a) and the percentage of inhibitor returned was less than 30% (Fig. 1b).
INHIBITOR SQUEEZE DESIGN
Based on the information derived from both the laboratory evaluation of commercially
available scale inhibitors and from the column simulation of an inhibitor squeeze under
simulated field conditions, a scale inhibitor squeeze treatment was designed for the A.E.
Guerra No. 43 gas well. The squeeze process included five phases, which are listed in Table
3.
Table 3. Design of a Scale Inhibitor Squeeze Treatment
Phase
Process
Volume
Additive
(bbl)
Composition
Concentration
1
(Preflush)*
25
HCl
0.5%
2
Pill
270
BHTMP (110 gals)
3537 mg/l
3
Overflush
250
Filtered field brine
4
Shut-in (48 hours)
5
Production
Since an acid treatment had been used two days prior to the actual squeeze treatment,
in order to remove any existing scale, no acid preflush was used for this squeeze.
Normally, however, an acid preflush would be recommended.
The preflush solution (i.e., 0.5% hydrochloric acid with a corrosion inhibitor) was used
to clean the production tubing by removing calcium carbonate scale deposits. The squeeze
pill consists of the scale inhibitor (i.e., bis-hexamethylene triamine tetramethylene
phosphonic acid, BHTMP in acid form) dissolved in filtered produced water. An overflush
was used to push the inhibitor pill farther into the reservoir formation. A shut-in period of
two days was necessary to allow adsorption of the inhibitor onto the formation rock through a
reaction of the inhibitor acid with the formation material.
INHIBITOR SQUEEZE LIFETIME AND ECONOMIC IMPACT
The inhibitor squeeze was performed on December 21, 1993. After the two-day shut-in,
the well was returned to production. Long-term monitoring of the inhibitor return has been
performed since the squeeze.
The concentration of the inhibitor returned as a function of the cumulative volume of
brine produced since the squeeze is presented in Fig. 2. The inhibitor concentration remained
above 1 mg/l for the initial 20,000 bbl of brine produced (approximately 167 days) and
maintained around 0.5 mg/l for over 50,000 bbl of brine produced (about 417 days) (Fig. 2a).
After 18 months, the amount of inhibitor returned was less than 20% of the total amount of
the inhibitor squeezed (Fig. 2b).
132
Hinrichsen et al.
a
1000
100
10
10000
20000
30000
40000
50000
15
10
10000
20000
30000
40000
50000
133
After the squeeze, the Guerra well produced gas and oil with few problems due to scale
formation for about 18 months. During this period, the well was periodically tested for
downhole scale. Recently, the gas production fell off due to a blockage caused by scale
formation. Scale samples were recovered and found to be mostly barium sulfate. A new
squeeze treatment is planned. Since a light deposit of calcium carbonate was found in the end
of the production tubing, the next squeeze treatment will include a mixed inhibitor treatment
for preventing both calcium carbonate and barium sulfate scale deposition.
The cost savings for the chemical squeeze are estimated to be over US $80,000/year for
this well alone. Furthermore, 24 days of added production per year has been realized by not
having to shut in the well for scale removal. This has produced an additional US
$150,000/year in cash flow.
CONCLUSIONS
The problem of barium sulfate scaling in downhole tubing in the subject gas well was
eliminated by a scale inhibitor squeeze using BHTMP. The squeeze has lasted for 18 months.
Cost savings are estimated to be more than US $80,000/year. The following conclusions can
be drawn from this case study:
1. BHTMP is an efficient inhibitor of barium sulfate scaling, especially in high calcium
brines.
2. Inhibitor squeeze treatment is an effective and economic method for controlling scale
deposition in downhole conditions in an oil and gas production system.
3. In the inhibitor squeeze treatment, blends of inhibitors may be needed instead of a
single inhibitor to control the formation of mixed mineral scales, such as barium
sulfate and calcium carbonate. Such combinations are presently being tested.
ACKNOWLEDGMENTS
This work was supported, in part, by the Gas Research Institute and by a consortium of
companies including Texaco, Inc.; Conoco, Inc.; Champion Technologies, Inc.; FMC
Corporation; Product Additives Division; and Zapata, Inc. The authors would like to thank
Texaco, Inc. for permission to publish this paper. The authors would also like to express their
deep appreciation to Saudi Arabian Texaco for supporting this presentation at the Second
Arabian Corrosion Conference.
REFERENCES
1. J.E. Oddo and M.B. Tomson, Algorithms can predict; inhibitors can control NORM
scale. Oil and Gas Journal, 1994, pp. 33-37.
2. S.L. He and J.W. Morse, Prediction of halite, gypsum and anhydrite solubility in
natural brines under subsurface conditions, Computers and Geosciences 19, l, 1993,
pp. 1-22.
3. S.L. He, J.E. Oddo and M.B. Tomson, The inhibition of gypsum and barite nucleation
in NaCl brines at temperatures from 25 to 90C, Appl. Geochemistry 9, 1994, pp. 561567.
134
Hinrichsen et al.
4. J.E. Oddo and M.B. Tomson, Elevated temperature-pressure flow simulator, U.S.
Patent No. 5,370,799.
135
ABSTRACT
Control of microbially induced corrosion (MIC) involves the application of biocides that
eliminate the deleterious microorganisms, resulting in a reduced corrosion rate of the material of
interest. However, the electrochemical properties of such chemicals in promoting or inhibiting
corrosion processes are not well understood. The present investigation is focused on the evaluation of
biocides commonly used in the oil fields and power sectors, from an electrochemical point of view.
This study examines the use of oxidizing and nonoxidizing biocides in sulfide contaminated saline
solutions. Gluteraldehyde (1,5-pentanedial) was chosen as a nonoxidizing biocide and ammonium
chloride, which is the principal chemical used in the in-situ generation of chloramine, as the oxidizing
biocide. A chemical environment of sulfide in seawater in a deaerated state was set up to simulate the
conditions occurring during biological processes. The biocides investigated were found to alter the
corrosion tendencies of mild steel and pitting tendency of 316L stainless steel in this environment.
Key Words: Mild steel, stainless steel, glutaraldehyde (1,5-pentanedial), ammonium
chloride, sulfide, biocides, corrosion, microbially induced corrosion,
MIC
INTRODUCTION
Extensive available literature [1-4] relating to microbially induced corrosion (MIC) has
indicated that MIC certainly remains as an incessant problem for the corrosion world.
Moreover, MIC is regarded as an intolerable corrosion problem, and multi-disciplinary effort
have been expended to undermine its detrimental effects and to understand the phenomenon
and its mechanisms [5-9]. All the engineering materials in general use, notably carbon steel
and stainless steels in oil fields and the power sectors are susceptible to some form of
microbial corrosion which usually arises from the activities of a wide range of
microorganisms and their usually oxidizing metabolic products.
The biological influences can be divided into three general categories [10]: production of
differential aeration or chemical concentration cells, production of organic and inorganic
acids as metabolic by products, and production of sulfides under oxygen-free (i.e., anaerobic)
conditions. Several studies have focused on MIC of carbon steels [3] and steel alloys
containing 2-3% Mo [6-8]. Control of MIC usually involves the utilization of chemical
biocides. These chemicals are sometimes misunderstood and misused in processes involving
aqueous environments due to a lack of understanding of the nature of the problem. Very little
effort [11] has been made to investigate the effects of biocides that are used in oil fields and
135
power generation systems on the electrochemical behavior of metallic materials. Most of the
research [12-13] has been concerned with the biocidal properties of the chemicals that are
used to combat biologically induced corrosion problems and not the electrochemical
properties of those chemicals.
Biocides are categorized as either oxidizing or nonoxidizing toxicants. The selection and
application of suitable biocide treatment depends on the broad spectrum activity, pH,
economics, compatibility with the other chemicals used for treatment, and most importantly,
suitability with the materials of construction from a corrosion point of view. Glutaraldehyde
(1,5-pentanedial), a nonoxidizing biocide, is extensively used in oil fields. Chlorination is
commonly employed in the treatment of freshwater systems. Chlorine is the most widely
used industrial oxidizing biocide. Ammonium chloride, an oxidizing chemical, is commonly
used in the in-situ generation of chloramine as an oxidizing biocide.
The present investigation is focused on investigating the electrochemical nature of
glutaraldehyde, as a nonoxidizing chemical, on the corrosion effects of mild steel and 316L
stainless steel in deaerated synthetic seawater media containing sulfide to simulate the effects
of biogenic sulfides generated by sulfate reducing bacteria (SRB) the most documented
deleterious organism in MIC, under anaerobic conditions. Also, ammonium chloride, an
oxidizing chemical, is investigated under similar conditions simulating biogenic sulfides
generated by SRB.
EXPERIMENTAL PROCEDURE
Carbon steel (UNS G10200) and 316L stainless steel (UNS 316003) of exposed areas of
1 cm2 were used for this study. The working electrodes were polished with emery papers to a
600 grit finish. The polished specimens were successively rinsed with analar grade acetone
and double distilled water, and then air dried. Experiments for corrosion measurements were
conducted utilizing standard seawater. This was prepared with distilled water and standard
seawater salt. Standard seawater salt (Marinemix + Bio-Elements from Wiegandt GMBH &
Co., F.R. Germany) was used to reduce the variability of effects resulting from conducting
measurements using natural seawater. Experiments were also conducted in sulfide polluted
seawater. The sulfide was introduced using research-grade sodium sulfide (Na2S). The level
of sulfide in the seawater was checked by the iodimetric method of analysis. The synthetic
seawater solutions were deaerated using purified nitrogen gas. Sulfide was introduced to
these solutions as sodium sulfide in the concentrations of 1 and 10 ppm. Glutaraldehyde (1,5pentanedial) was selected as the nonoxidizing-type of biocide in concentrations of 10, 50 and
100 ppm and, ammonium chloride was selected as the oxidizing agent in the concentration
range of 1, 5 and 10 ppm. Electrochemical measurements employing linear polarization,
Tafel extrapolation, potentiodynamic polarization and AC impedance techniques were carried
out in the three-electrode cell assembly (EG&G). The reference electrode used was a
saturated calomel electrode (SCE), located in a glass tube fitted with vycor frit and the
electrochemical circuit was completed with an encapsulating cylindrical platinum counter
electrode.
Polarization resistance (Rp) values were obtained by using linear polarization applying
Ecorr + 0 mV across the working electrodes surface. Tafel polarization studies were
performed by imposing Ecorr + 250 mV with respect to the open circuit potential (OCP). The
136
anodic polarization experiments were run at a scan rate of 0.5 mV/sec using a potentiostat
5
(EG&G model 273A). AC impedance data were generated as a function of frequency (10
Hz-10 mHz) by imposing a sinusoidal voltage signal of 5 mV across the interface. The
complex impedance data were acquired using a frequency response analyzer (Schlumberger
model SI1255) controlled by a computer. All the electrochemical measurements were made
o
under stagnant conditions at room temperature (i.e., 19 +
1 C).
RESULTS AND DISCUSSION
The Tafel polarization curves for mild steel in seawater and a sulfide-polluted system
under deaerated conditions are presented in Fig. 1a. Increasing the sulfide concentration
resulted in a shift in potential in the active direction. Also, increasing the sulfide level
resulted in a significant change in the values of ba and bc. At the same time, this resulted in
an increase in the corrosion rate for a higher concentration of sulfide, i.e., 10 ppm. Clearly
the presence of sulfide has a significant influence on the rate of the cathodic and anodic
reactions. From a comparison of the values of ba and bc at the two sulfide concentrations of
interest, it can be seen that increasing the sulfide concentration resulted in bc tending towards
increasing values which indicates a diffusion-limiting reaction occurring at the surface. This
is clearly a result of exposure to higher concentrations of sulfide ions which resulted in the
development of an oxidized layer acting as a diffusion barrier. Thus, it is possible that the
corrosion reaction was under mixed control. The limiting diffusion current was observed on
the cathodic branch of the polarization curve, as can be seen in Fig. 1a. This is consistent
with the conclusions of Iofa [14] that sulfide participates directly in the cathodic reactions and
is simply a catalyst which speeds up the discharge of hydrogen ions. Various mechanisms
have been proposed for the intensification of the corrosion rate due to the presence of
hydrogen sulfide [14-18]. An example of one such mechanism is that proposed by Panasenko
[16], i.e.,
Fe + HS
Fe(HS-)ads
Fe(HS-)ads
Fe(HS) + 2e
Fe
Fe(HS)
2+
+ HS-
(1)
(2)
(3)
It is clear that sulfide acts as a catalyst promoting ferrous ion generation. This will lead
to an increase in the concentrations of ferrous ions near the interface. The adsorption of HSions will produce a negative charge on the surface which will accelerate the hydrogen
discharge reaction through another simultaneous cathodic reaction [15]:
-
2-
HS + e
Hads + S
(4)
Hads + Hads
H2
(5)
137
-500
-500
0 ppm Glutaraldehyde
10 ppm Glutaraldehyde
50 ppm Glutaraldehyde
100 ppm Glutaraldehyde
Seawater
-600
1 ppm Sulfide
SCE
10 ppm Sulfide
-700
Potential, mV
Potential, mV
SCE
-600
-800
-900
-1000
-700
-800
-900
-1000
-1100
-1100
-9
-8
-7
-6
-5
-4
-3
-2
-10
-9
-8
-7
-6
-5
-4
-3
-2
log (i[A/cm ])
log (i[A/cm ])
(a)
(b)
-500
0 ppm NH 4Cl
1 ppm NH 4Cl
5 ppm NH 4Cl
10 ppm NH 4Cl
-500
0 ppm Glutaraldehyde
10 ppm Glutaraldehyde
50 ppm Glutaraldehyde
100 ppm Glutaraldehyde
SCE
-600
Potential, mV
Potential, mV
SCE
-600
-700
-800
-900
-700
-800
-900
-1000
-1000
-1100
-1100
-10
-9
-8
-7
-6
-5
-4
-3
-10
-2
-9
-8
-7
-6
-5
-4
-3
log (i[A/cm ])
log (i[A/cm ])
(c)
(d)
-500
0 ppm NH 4Cl
1ppm NH
Cl
4
5 ppm NH
Cl
4
10 ppm NH
Cl
Potential, mV
SCE
-600
-700
-800
-900
-1000
-1100
-10
-9
-8
-7
-6
-5
-4
-3
-2
log (i[A/cm ])
(e)
Figure 1. Polarization diagrams for mild steel in seawater: (a) without biocides; (b)
with glutaraldehyde and 1 ppm sulfide; (c) with glutaraldehyde and 10
ppm sulfide; (d) with ammonium chloride and 1 ppm sulfide; and (e)
with ammonium chloride and 10 ppm sulfide
138
-2
2-
At the pH of the present solution (9.7 9.75) S is not stable and thus the reaction
2-
+ H2O
HS- + OH
(6)
takes place, by which hydroxide ions are produced, increasing the pH of the solution.
However due to the high concentration of ferrous ions near the interface, another partial
reaction will compete with the reaction in Eq. 4, that is the precipitation of the solid sulfide
according to the following reaction:
Fe
2+
+ HS
(7)
Thus in this case, the corrosion current measurements for steel have indicated significant
increases in the presence of low concentrations of sulfide which is due to the formation of a
corrosion product which acts as a physical barrier to the corrosion reaction. However, the
anodic polarization curves from Fig. 1a show an increase in the anodic dissolution for a
sulfide-added system.
To investigate the effect of oxidizing biocide on the mild steel-sulfide-polluted seawater
system, glutaraldehyde and ammonium chloride were introduced. The Tafel polarization
curves for mild steel in deaerated sulfide-polluted seawater with various concentrations of
either glutaraldehyde or ammonium chloride are presented in Figs. 1b-e. The parameters
obtained from the linear polarization and Tafel extrapolation methods are given in Tables 1
and 2. It can be seen from these tables that the addition of sulfide increases the corrosion rate
of mild steel, especially in higher concentrations of sulfide as reflected both in the
measurement of Rp and corrosion current, icorr.
Table 1. The Electrochemical Parameters of Mild Steel and Stainless Steel
in Unpolluted Seawater
Alloy
Mild Steel
Stainless Steel
Parameter
OCP (mV vs SCE)
Rp, LP (K cm2)
icorr, (A/cm2)
Rp,Imp (K cm2)
Epit, (mV vs SCE)
Ipit (A/cm2)
Rp, LP (Kcm2)
Measured Value
776
12.38
0.508
6.87
64
2.69
236.3
10 ppm
Conc.
ppm
OCP, mV
vs SCE
-784
Rp (LP)
K cm2
10.670
icorr,
A/cm2
0.49
Rp (Imp)
K cm2
6.333
OCP, mV Rp (LP),
icorr,
vs SCE K cm2 A/cm2
-794
3.012
1.29
Rp (Imp)
K cm2
2.2610
Glutaraldehye
10
50
100
1
-810
-780
-799
-809
10.46
3.447
10.03
8.577
0.535
2.12
0.617
0.579
9.931
1.734
6.685
5.370
-816
-738
-816
-815
7.880
16.62
4.310
13.31
0.93
0.4
1.09
0.524
5.133
--4.383
---
Ammonium
Chloride
5
10
-806
-818
2.047
2.815
4.44
0.70
1.223
7.236
-782
-732
4.14
18.8
1.40
0.372
-----
The addition of ammonium chloride to the sulfide polluted system increased the
corrosion current and reduced the Rp values in the lower concentration of 1 ppm sulfide.
However, this scenario was not observed in the higher concentration of 10 ppm sulfide level
where decreases in the corrosion current values were noted for an increase in the ammonium
chloride concentration, except at 5 ppm. The Nyquist plots and Bode magnitude diagrams
obtained form the AC impedance measurements are presented in Figs. 2 and 3, respectively.
Because of the distinct advantage of the Bode magnitude plots over the Nyquist plots in the
low frequency range, the Rp values obtained from the Bode plots were taken into account for
the analysis and are presented in Tables 1 and 2. These measurements also indicated the
similar trends observed in the DC polarization measurements.
Some investigators [11] have shown that the analyses of results from the AC impedance
method are more appropriate than the DC polarization for the biocide added system where
potentiodynamic measurements yielded higher corrosion rates because of the change in the
surface of the system exposed to the biological environment during the polarization. It is a
general belief that the addition of biocide to the MIC system results in the elimination or the
control of the deleterious microorganisms, thereby reducing the corrosion rate of the material
of interest. The results from the previous investigations [19,28] on the glutaraldehyde-added
system were of a conflicting nature, because of the effect attributed to the release of
metabolic products during glutaraldehyde treatment which might change local pH and/or
inorganic species adjacent to the metal/solution interface, thereby interfering with the
corrosion of steel.
140
6
0 ppm Glutaraldehyde
10 ppm Glutaraldehyde
50 ppm Glutaraldehyde
100 ppm Glutaraldehyde
(KOhm.cm )
0 ppm Sulfide
1 ppm Sulfide
10 ppm Sulfide
imaginary
imaginary
(KOhm.cm )
0
0
real
(KOhm.cm )
10
12
real
(KOhm.cm )
(a)
(b)
6
(KOhm.cm )
imaginary
0 ppm NH 4Cl
1 ppm NH Cl
4
5 ppm NH 4Cl
10 ppm NH Cl
4
3
imaginary
10
(KOhm.cm )
0 ppm Glutaraldehyde
10 ppm Glutaraldehyde
50 ppm Glutaraldehyde
100 ppm Glutaraldehyde
12
0
0
10
12
real
(KOhm.cm )
(c)
real
10
12
2
14
16
(KOhm.cm )
(d)
0 ppm NH Cl
4
1 ppm NH Cl
4
5 ppm NH Cl
4
10 ppm NH 4Cl
12
10
8
6
4
imaginary
(KOhm.cm )
14
2
0
0
10
12
real
(KOhm.cm )
(e)
Figure 2. Nyquist plots for mild steel in seawater: (a) without biocides; (b) with
glutaraldehyde and 1 ppm sulfide; (c) with glutaraldehyde and 10
ppm sulfide; (d) with ammonium chloride and 1 ppm sulfide; and
(e) with ammonium chloride and 10 ppm sulfide
141
4
0 ppm Sulfide
0 ppm Glutaraldehyde
10 ppm Glutaraldehyde
3.5
50 ppm Glutaraldehyde
100 ppm Glutaraldehyde
2
3
1 ppm Sulfide
10 ppm Sulfide
3.5
2.5
1.5
3
2.5
1.5
-4
-2
-4
-2
Log [frequency], Hz
Log [frequency], Hz
(a)
(b)
4.5
0 ppm Glutaraldehyde
10 ppm Glutaraldehyde
50 ppm Glutaraldehyde
100 ppm Glutaraldehyde
0 ppm NH 4Cl
4
1 ppm NH Cl
4
5 ppm NH 4Cl
3.5
4.5
3
2.5
2
1.5
3.5
10 ppm NH 4Cl
3
2.5
2
1.5
-4
-2
-4
-2
Log [frequency], Hz
Log [frequency], Hz
(c)
(d)
4.5
0 ppm NH Cl
4
1 ppm NH 4Cl
5 ppm NH 4Cl
3.5
10 ppm NH Cl
4
3
2.5
2
1.5
1
-4
-2
Log [frequency], Hz
(e)
Figure 3. Bode plots for mild steel in seawater: (a) without biocides; (b) with
glutaraldehyde and 1 ppm sulfide; (c) with glutaraldehyde and 10 ppm
142
sulfide; (d) with ammonium chloride and 1 ppm sulfide; and (e) with
ammonium chloride and 10 ppm sulfide
It is believed that glutaraldehyde enters into interaction with sulfide and forms
thioglutaraldehyde that polymerizes on the metal surface. It is possible that organic
compounds are capable of entering into chemical interaction with the sulfide present, forming
on the metal surface insoluble compounds (i.e., Eq. 6) that constitute a peculiar kind of phase
barrier. It is possible that localized alteration of pH at the electrode surface (Eq. 4,) makes
this mechanism possible.
However, the addition of ammonium chloride can certainly decreases the resistance of
mild steel in any sulfide system because of its oxidizing nature. In the 1 ppm sulfide system,
the co-presence of ammonium chloride and oxidized forms of sulfide promotes the corrosion
process. Increasing the concentration of sulfide in a system containing NH4Cl, resulted a the
decrease in the corrosion current. This can be attributed to the formation of species such as
sulfate as the oxidized product of sulfide in the presence of NH4Cl. Also the increased
dissolution rate observed in the intermediate concentration of 5 ppm of ammonium chloride
compared with other concentrations call attention to the existence of a critical concentration
of oxidizing-types of chemicals, like passivators added to a neutral medium.
Stainless Steel
The anodic polarization curves for stainless steel in deaerated sulfide added to a biocide
system are presented in Figs. 4a-e. These curves yielded important parameters which are
presented in Tables 1 and 3, and are relevant to the assessment of 316L stainless steel in a
biocide added system. The pitting potential values shown in Tables 1 and 3 clearly indicate
the influence of sulfide on the passivity of stainless steel in a deaerated, biocide-free system.
It is well known that sulfide anions present in polluted seawater lead to the formation of an
oxide layer of poor protective characteristics, which facilitates the initiation of corrosion
attack [21]. Moreover, the presence of sulfide in a stainless steel-seawater system is
generally detrimental to the pitting resistance of all stainless steel grades. The biologically
generated sulfide can also modify the local chemistry of the marine environment and prevent
the repair of the passive film of the stainless steel [22].
Table 3. The Effects of the Investigated Biocides on the Electrochemical Parameters of 316L
Stainless Steel in Sulfide Polluted Seawater
Sulfide Concentration
1 ppm
10 ppm
Rp, cm
Ip, A/cm
275.7
10
50
100
1
5
10
Biocides
Investigated
None
Conc.
(ppm)
Glutaraldehye
Ammonium
Chloride
Rp, cm
2.55
Epit mV
vs SCE
251
278.6
180.6
219.7
2.44
2.70
2.55
144.4
392.7
164.4
3.2
2.17
3.45
148.6
Ip,
A/cm2
3.04
Epit mV
vs SCEE
142
159
95
198
206.7
238.9
169.3
3.4
2.52
3.08
223
125
193
104
172
158
226.9
172
152.1
3.02
5.06
3.13
264
196
169
143
600
0 ppm Glutaraldehyde
10 ppm Glutaraldehyde
50 ppm Glutaraldehyde
100 ppm Glutaraldehyde
400
Seawater
400
SCE
1 ppm Sulfide
10 ppm Sulfide
200
Potential, mV
SCE
300
Potential, mV
100
0
-100
-200
200
-200
-300
-400
-400
-10
-9
-8
-7
-6
-5
-4
-10
-3
-9
-8
-7
-6
0 ppm Glutaraldehyde
10 ppm Glutaraldehyde
50 ppm Glutaraldehyde
100 ppm Glutaraldehyde
0 ppm NH Cl
4
1 ppm NH Cl
400
5 ppm NH 4Cl
10 ppm NH Cl
SCE
200
-200
200
-200
-400
-400
-10
-9
-8
-7
-6
-5
-4
-3
-10
-9
-8
-7
-6
-5
-4
log (i[A/cm ])
log (i[A/cm ])
(c)
(d)
0 ppm NH Cl
4
1 ppm NH Cl
400
Potential, mV
SCE
5 ppm NH Cl
4
10 ppm NH Cl
4
200
-200
-400
-10
-9
-8
-7
-6
-5
-4
-3
-2
log (i[A/cm ])
(e)
Figure 4. Polarization diagrams for 316L stainless steel in seawater: (a) without
biocides; (b) with glutaraldehyde and 1 ppm sulfide; (c) with
144
-3
(b)
Potential, mV
SCE
Potential, mV
-4
log (i[A/cm ])
(a)
400
-5
2
log (i[A/cm ])
-3
145
250
200
0 ppm glutaraldehyde
10 ppm glutaraldehyde
50 ppm glutaraldehyde
100 ppm glutaraldehyde
(KOhm.cm )
1 ppm Sulfide
10 ppm sulfide
200
150
150
imaginary
100
50
100
50
imaginary
(KOhm.cm )
0 ppm sulfide
0
0
50
100
150
20
40
real
(KOhm.cm )
60
80
100
120
2
(KOhm.cm
real
(a)
140
160
(b)
0 ppm Glutaraldehyde
10 ppm Glutaraldehyde
50 ppm Glutaraldehyde
100 ppm Glutaraldehyde
250
0 ppm NH 4 Cl
1 ppm NH 4 Cl
5 ppm NH Cl
4
10 ppm NH Cl
200
(KOhm.cm )
150
150
100
imaginary
100
50
imaginary
(KOhm.cm )
200
0
0
50
100
50
150
50
real
(KOhm.cm )
(c)
real
100
(KOhm.cm
150
2
(d)
200
150
100
50
imaginary
(KOhm.cm )
0 ppm NH 4 Cl
0
0
50
100
real
150
(KOhm.cm
200
2
250
(e)
Figure 5. Nyquist plot for 316L stainless steel in seawater: (a) without biocides;
(b) with glutaraldehyde and 1 ppm sulfide; (c) with glutaraldehyde and
10 ppm sulfide; (d) with ammonium chloride and 1 ppm sulfide; and
(e) with ammonium chloride and 10 ppm sulfide in seawater
146
0 ppm Sulfide
0 ppm glutaraldehyde
10 ppm glutaraldehyde
50 ppm glutaraldehyde
100 ppm glutaraldehyde
1 ppm Sulfide
5
10 ppm Sulfide
-4
-2
-4
-2
Log [frequency], Hz
Log [frequency], Hz
(a)
(b)
6
0 ppm NH Cl
4
1 ppm NH 4 Cl
5 ppm NH Cl
4
10 ppm NH 4Cl
0 ppm glutaraldehyde
10 ppm glutaraldehyde
50 ppm glutaraldehyde
100 ppm glutaraldehyde
-4
-2
-4
-2
Log [frequency], Hz
Log [frequency], Hz
(c)
(d)
6
0 ppm NH 4Cl
1 ppm NH 4Cl
5 ppm NH 4Cl
10 ppm NH 4Cl
1
-4
-2
Log [frequency], Hz
(e)
Figure 6. Bode plot for 316L stainless steel in seawater: (a) without biocides; (b)
with glutaraldehyde and 1 ppm sulfide; (c) with glutaraldehyde and
10 ppm sulfide; (d) with ammonium chloride and 1 ppm sulfide; and
(e) with ammonium chloride and 10 ppm sulfide
147
In the present investigation, the effect of sulfide on the passivity breakdown, thereby
increasing the pitting tendency, for the increase in sulfide concentration is clearly revealed.
The addition of glutaraldehyde, a nonoxidizing biocide, also resulted in a lower pitting
potential than the blank system. The least was observed for the intermediate concentration of
50 ppm. The analysis based on the anodic current density corresponds to the passive region
indicating that the susceptibility mode is more pronounced than in the biocide-free system.
The addition of ammonium chloride as an oxidizing chemical changed the entire scenario and
involved an increased susceptibility of stainless steels to pitting. The pitting potential values
from Tables 1 and 3 indicate this effect. This is not the case all the time or for all
concentrations investigated. Increases in the concentration of sulfide to 10 ppm with the
addition of NH4Cl resulted in improved pitting resistance based on the pitting potential values
compared to the blank one. The anodic current density values corresponding to the passive
region showed a high value for the concentration of 5 ppm of ammonium chloride. The same
concentration for mild steel in a sulfide-polluted system increased the dissolution rate. Under
inorganic, near neutral conditions, sulfide and other sulfur species are known to decrease both
the pitting potential and the repassivation potential of stainless steels [23]. Particularly,
chloride ions are aggressive to stainless steels. The pitting potential is reduced as the
concentration of chloride increases [24]. However, the effects of the aggressive anions are
reduced by the presence of inhibiting anions. Notably sulfate [24], hydroxide [25] and
acetate [25] inhibit the pitting corrosion of stainless steel to varying extents, and this was the
case observed in the present investigation for higher concentrations of sulfide where the
presence of an oxidizing agent led to the formation of sulfate as the resultant oxidizing
product. Figures 5a-e and 6a-e-show the complex plane impedance diagrams (Nyquist plots)
and the Bode plots for 316L stainless steel in seawater with and without a sulfide polluted
system (i.e., addition of glutaraldehyde and ammonium chloride. These plots do not allow a
reasonable estimate for Rp because the valid Rp values can only be obtained using the AC
impedance technique if the low frequency locus in the complex plane impedance diagram is
essentially complete. The behavior, however, is of the Warburg type for diffusion controlled
reactions.
CONCLUSIONS
1. The oxidizing and nonoxidizing biocides generally alter the corrosion tendency of
mild steel and the pitting tendency of 316L stainless steel in sulfide polluted
environments.
2. The increase in corrosion rate of mild steel was observed for the glutaraldehyde
concentration of 50 ppm added to the lower concentration of sulfide i.e., 1 ppm. This
trend completely reversed for a higher concentration of sulfide i.e., 10 ppm.
3. The increase in the concentration of sulfide, i.e., 10 ppm, for the oxidizing type of
chemical added to the synthetic seawater resulted in a decrease of the corrosion rate of
mild steel as well as a lower pitting susceptibility for stainless steel.
ACKNOWLEDGMENT
This work was supported financially by the Kuwait Foundation for the Advancement of
Science (KFAS) and Kuwait University. This support is gratefully acknowledged.
148
REFERENCES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
H.A. Videla, M.F.L. Demele and G.J. Brankevich, Corrosion 44, 1988, pp. 423-426.
S.C. Dexter, K.E. Lucas and Y. Gao, in Biologically Induced Corrosion, S.C. Dexter,
ed., NACE, Houston, Texas, 1986, pp. 144-153.
R.C. Salvarezza and H.A. Videla, Corrosion 36, 1980, pp. 550-553.
R. Johnson and E. Bardal, Corrosion/86, Paper No. 227, NACE, Houston, Texas,
1986.
R.G.J. Edyvean, Proceedings 6th International Congress on Marine Corrosion and
Fouling, 1984, Athens, pp. 469-483.
R.G.J. Edyvean and L.A. Terry, UK Corrosion84, Institute of Corrosion84, Institute
of Corrosion Science and Technology, UK, 1984, pp. 195-198.
G. Kobrin, in Biologically Induced Corrosion, S.C. Dexter, ed., NACE, Texas, USA,
1986, p. 33.
R.E. Tantnall, Materials Performance 19, 8, 1980, p. 88.
R.J. Soracco, D.H. Pope, J.M. Eggars and T.N. Effinger, Corrosion/88, Paper No.83,
NACE, Houston, Texas, 1988.
C.A.C. Sequeira, Proceedings 2nd EFC Workshop on Microbial Corrosion, The
Institute of Materials, UK, 1992, p. 9.
M. Elbonjdaini and V.S. Sastri, Corrosion/95, Paper No. 213, NACE, Texas, USA,
1995.
J.E. Lamot, Proceedings First European Federation of Corrosion Workshop on
Microbial Corrosion, The European Federation of Corrosion, 1988, pp. 224-234.
W.I.J. Poulton and R.W. Lutey, Proceedings International Congress on Microbially
Induced Corrosion, Tennessee, USA, 1990.
Z.A. Iofa, Zashchite Metallov 6, 5, 1970, p. 491.
I.L. Rozenfeld, Corrosion Inhibitors, McGraw-Hill, New York, 1981.
V.F. Panasenko, Candidates Dissertation, Poly-Tech. Institute, Kiev, 1972.
H. Kaesche, Werkstoffe und Korrosion 21, 3, 1970, p. 185.
P. Bolmer, Corrosion 21, 3, 1965, p. 69.
R.G. Eager, J. Leder, J.P. Stanley and A.B. Theis, Corrosion/88, Paper No. 84,
NACE, Houston, Texas, USA, 1988.
J.S. Luo, P. Angell and D.C. White, Proceedings 9th Asian-Pacific Corrosion Control
Conference, Taiwan, China, 1995, p. 592.
R.G.J. Edyvean and H.A. Videla, Proceeding 2nd EFC Workshop on Microbial
Corrosion, the Institute of Materials, UK, 1992, p. 18.
Z. Szklarska-Smialowska and E. Lunarska, Werkstoffe und Korrosion 32, 1981, p.
478.
R.C. Newman, H.S. Isaacs and B. Alman, Corrosion 38, 1982, p. 261.
H.P. Leckie and H.H. Uhlig, J. Electrochem. Soc. 113, 12, 1966, p. 1262.
Z. Szklarska-Smialowska, Pitting Corrosion of Metals, NACE, Houston, Texas,
USA, 1986, p. 285.
149
Oil Plus Limited, Hambridge Road, Newbury, Berkshire, RG14 5TR, England
Kuwait Institute of Scientific Research, P.O. Box 24885, 13109 Safat, Kuwait
ABSTRACT
Injection of seawater and produced (effluent) water for secondary oil recovery can encourage the
growth of bacteria, particularly in biofilms on pipewall surfaces. One particular problem in water
injection systems is the uncontrolled growth of sulphate-reducing bacteria (SRB) which leads to
increased corrosion of the process plant. Injection water sources in Kuwait range from brackish water
(total dissolved solids, i.e., TDS = 4,000 mg/l) through seawater (TDS = 30,000 mg/l) to highly saline
brines (TDS = 200,000 mg/l). In addition, some of these water sources are highly sulphide sour and
may require treatment to prevent scaling, corrosion or iron sulphide precipitation.
Studies were undertaken to evaluate the relative risks of microbially influenced corrosion in a
range of Kuwaits water sources, using a combination of field sampling and laboratory biofouling
trials. Bacteria isolated from the field surveys were used to evaluate remedial treatments such as
chlorine, chemical biocides and mechanical removal. Recirculating biofouling loops were set up with
the appropriate site water, and inoculated with the bacteria from the system so that an active biofilm
was set up on small steel studs. These biofouled studs were treated with proprietary antibacterial
products under various dose regimes in order to select the most appropriate control regime for
particular water chemistries and process options.
Key Words: Microbially influenced corrosion, seawater, water injection systems, secondary oil
recovery, remedial treatments
INTRODUCTION
Pitting corrosion is characteristic of sulphate reducing bacteria (SRB) attack of steels,
with the pits being open and filled with soft black corrosion products in the form of iron
sulphides [1,2]. When the corrosion products are removed, the metal underneath is bright but
rapidly rusts on exposure to air. With buried pipelines in anaerobic environments, such as
waterlogged clay soils, the corroded area as a whole, will be covered with a film of iron
sulphides. In aerobic environments, SRB corrosion invariably occurs beneath deposits of
inorganic or organic detritus, microbial slimes, or tubercules caused by the action of the ironoxidising bacteria [3,4].
Unique features of corrosion caused by SRB are that it occurs at neutral pH and in
anaerobic environments. Oxygen is not involved, and the corrosion products include iron
149
sulphides. The exact mechanisms of the corrosion reactions are still under debate, and a
range of possible mechanisms has been proposed [1,2].
Normal electrochemical corrosion would not be expected to occur under anaerobic
conditions, because the cathode becomes polarized by the build-up of a layer of atomic
hydrogen. SRB are potentially able to stimulate the normal electrochemical corrosion
mechanism by a number of possible means, the most widely accepted being
It is now generally accepted that, although all of these mechanisms may operate in
nature, the production of iron sulphides and cathodic depolarisation are the two most
important corrosion mechanisms.
Control of microbes can be effected by chlorination, ozonization, by means of ultraviolet
(UV) light and/or organic biocides. A combination of these methods is commonly used to
minimise microbially influenced corrosion and reservoir souring in oilfield water injection
and reservoir systems. For seawater injection dosing systems, chlorine injection at the
seawater lift pumps is the most common primary method of control [5]. However, chlorine is
generally lost at the deaeration stage by reaction with oxygen scavenger, and biological
control is therefore maintained in the remainder of the system by the use of organic chemical
biocides. The most common strategy is a regular (frequently weekly) batch treatment for 3-6
hours. The dose rate and contact time are both critical in order to optimise the killing effect
of the biocide;: in most cases laboratory trials are used to determine the best treatment.
Most water injection systems, therefore, employ chemical biocide treatments [6,7] with
varying degrees of success [8,9]. Great care must be taken in selecting and applying biocides
to ensure that they are compatible with the system, can be handled safety, and have no
environmental impact. Additionally, both batch and low-level continuous treatments of
organic biocides will ultimately lead to the build-up of resistant and tolerant strains of the
bacteria. Biocide effectiveness will, therefore, decline with time, and monitoring must take
place to identify when a change in biocide type is required.
In most cases, a proprietary organic biocide is used as a batch dose to replace the
continuous microbiological control exerted by chlorine. There are many biocides offered by
chemical supply companies, which may carry out field tests to determine which of their range
is best suited to a particular problem. An unbiased view can, however, only be given by the
operator or an independent laboratory carrying out a testing program for products from a
range of supply companies. Despite the apparent large range of biocides, there are, in fact, a
relatively limited number of molecules that are regularly used. The most widely used
biocides are listed below. Many products are mixtures of one or more biocides with
surfactant that aids penetration of deposits and provides cleansing action.
Sanders et al.
151
Simple recirculating biofilm generators are set up in the laboratory to mimic system
conditions, allowing biofouling to occur with bacteria freshly isolated from the system. After
a period of biofouling, the biostuds are removed and placed in stirred test biocide solutions in
anaerobic seawater. After the desired contact time, these are removed and the surviving
bacteria are enumerated, thus enabling TK curves to be determined for each biocide.
Special Tests
Appropriate test methods should be devised for other systems; for example, biocides for
reservoir application should be tested at high temperature and pressure and with the presence
of sand. Sand-packed columns are also useful for selecting biocides for hydrocarbon
reservoir production system applications.
Field Test Methods
Both planktonic and sessile biocide trials can be carried out in the field on samples of
water, solids or biostuds, derived from the system. A side stream is ideal for this purpose as
biostuds can be used. Whilst laboratory derived results may relate to the system under study,
it is generally better to carry out such tests in the field, under system conditions, so that the
results can be directly related to the system [9,14,15].
In order to confirm the performance of a selected biocide regime, close monitoring of the
system should be carried out before and after any change is made, by analysing the biostuds
before and after biocide dosing. Once effectiveness is confirmed, monitoring can revert to a
normal schedule until biocide-resistant and tolerant strains build up in the system.
METHODS
Three different systems in Kuwait were studied for their biocide treatment requirements.
These were
152
Sanders et al.
153
Biocide Dosing
Biocides were supplied in labelled bottles by the chemical vendors. Samples were
withdrawn from the bottles and used in the laboratory tests. Table 1 gives the details of the
products supplied for testing.
For stirred biocide tests, products were made up to the desired concentration in site water
in 125 ml Wheaton bottles; dispensing was carried out using adjustable automatic micro
pipettors and suitable dilution. For the sulphide-free tests, the studs were added directly to
the biocide solution; for the tests containing sulphide, a stock sulphide solution was made up
and the appropriate volume added to the Wheaton bottle to give the desired concentration,
prior to adding the stud to the biocide. Studs were removed from the SBMTs and suspended
in the biocide/sulphide solution before assessing surviving bacterial numbers.
For dynamic tests, biocides were injected directly into the SBMTs at the desired
concentration, and the studs were removed before and after dosing. Subsequently, biocide
doses were repeated at increasing concentrations to identify the most effective regime.
Bacterial Evaluation
The exposed surface of the stud was scraped carefully and all deposits were transferred
to 10 cm3 of sterile seawater diluent. The diluent tube was then treated for 30 seconds in an
ultrasonic bath followed by 60 seconds in a vortex mixer and a further 30 seconds in the
ultrasonic bath. This treatment disrupts biofilm/deposits but does not kill bacteria. The
treated diluent tube was used to inoculate triplicate series (to 10-7) of the following media,
154
Sanders et al.
specially formulated for the bacteria grown from each site: SRB - Postgates B; GAB glucose-based aerobic broth; Gan - glucose based anaerobic broth.
One cubic centimetre of the diluent was injected into each broth series and 1 in 10
dilutions were made. The procedure followed industry standard practice for MPN (most
probable number) tests [13]. GAB and GAnB results were taken after 5 days of incubation at
30C. SRB results were taken after 28 days of incubation at 30C.
CASE HISTORY 1: PRODUCED EFFLUENT WATER REINJECTION SYSTEM,
WEST KUWAIT
A complex system with various water sources for potential reinjection into the oil
reservoir was tested. A 50:50 mixture of produced water and aquifer water was selected to be
A full range of tests was carried out on 9 biocide products (see Table 1). MIC,
planktonic time-kill, sessile time-kill, chlorination and mechanical removal were all tested,
with and without 75 mg/l of sulphide.
Due to the high salinity and high H2S content of the water, bacterial fouling was low in
both the system and the laboratory BETR. In fact, it proved difficult to isolate bacteria from
the system.
The simple MIC tests yielded a generalized ranking of the products, but little information
could be gained about the realistic dose rates required. More information was obtained from
the planktonic time-kill tests, particularly with respect to speed of kill. The most realistic
testing (against sessile bacteria) in the sulphide-free scenario gave a very similar ranking to
the planktonic tests. Very importantly, however, the resulting recommended dose rates are
much higher against sessile bacteria because of the high bactericide demand caused by the
presence of inactivating organic materials in the biofilm.
Table 1. Results of Testing of Nine Biocide Products on a Complex Produced Effluent Water
Biocid
e
Formulation
Ranking
(MIC)
1A
Mixed Aldehydes
+ QAC + QPC
Mixed Aldehydes
+ QAC
Glutaraldehyde +
QPC
Aldehydes
+
QAC
Fatty Amines
Aldehydes
+
QAC + Surfactant
Glutaraldehyde
Mixed Aldehydes
+
QAC
+
Surfactant
Formaldehyde +
1B
1C
1D
1E
1F
1G
1H
1I
2=
Planktonic Time-Kill
(Sweet)
Ranking
Dose
(ppm/hrs)
6
100/6
5
100/6
8
2=
100/6
1
5=
2=
100/6
5=
7
2=
1
100/6
25/6
Sessile Time-Kill
(Sweet)
Ranki
Dose
ng
(ppm/hrs)
5
>>500/6
6
2=
5=
Planktonic Time-Kill
(Sour)
Ran
Dose
king
(ppm/hrs)
3
100/3
>>500/6
100/6
4
1
100/1
25/3
25/6
100/3
Sessile
(
Rankin
g
2
4
3
500/6
500/6
4
1
>500/6
500/3
3
5
1
155
QPC
representative of the system. This mixture had a TDS of 130,000 mg/l. One stream had a
TDS of 259,000 mg/l, whilst another was of brackish water composition. One of the waters
contained a sulphide level of 75 mg/l, and therefore, sour conditions were also tested.
A similar picture emerged from the sour testing. As with the sulphide-free tests, the
sessile ranking was similar to the planktonic ranking for the sulphide-containing tests. The
only difference in the rankings was that Biocide 1A (effective in planktonic tests) was not
very effective in the sessile tests, probably due to a lack of penetration into the biofilm.
Again, a much higher demand for biocide is indicated when the sessile and planktonic tests
are compared. The comparison of the planktonic and sessile rankings (Table 2) indicates the
comparability between the two types of tests.
Chlorination at conventional levels will not, in fact, be effective in controlling planktonic
bacteria, even under the most favourable conditions. GAB numbers were initially 1.4 x
105/ml, and no measurable reduction was detected at 0.2 mg/l over 2 hours. Even at 2 mg/l
for 2 hours, GAB were only reduced to 4.5 x 104/ml (i.e., less than one order of magnitude).
GAnB showed slightly better kill rates, but 2 mg/l free chlorine only reduced numbers by one
order of magnitude (from 4.5 x 104/ml to 3.0 x 103/ml). SRB behaved similarly (1.5 x 104/ml
was reduced to 1.4 x 103/ml by 2 mg/l chlorine over 2 hours). Chlorination was, therefore,
not considered as a feasible treatment regime for this system.
Physical removal of corrosion deposits, biofouling, scale, settled solids, etc., in pipelines
and vessels is a common cleanup method. A wide range of cleaning tools and devices are
available to mechanically clean pipelines. These include foam spheres, nylon brush pigs,
wire brush pigs, flexible plastic pigs and (the most aggressive) milling pigs.
Normal oilfield operations combine chemical treatment programs (including biocides)
with regular pigging operations of pipelines. Different types of physical removal of biofilms
were tested, using the biofouled studs from the SBMTs. Initial bacterial populations
consisted of 2.5 x 104 GAB, 2.0 x 104 GAnB and 4.5 x 104 SRB per stud. The biofilm was
very thin and corrosion products were not in evidence. This meant that even a small physical
perturbation was sufficient to dramatically reduce the numbers of sessile bacteria.
Table 2. A Comparison of Planktonic and Sessile Rankings
Bactericide
Planktonic Ranking
Sessile Ranking
1H
1F
1D
1G
1A
1B
1
2=
2=
4
6
5
1
2
3
4
5
5
Sessile Ranking
Recommended Dose
Sanders et al.
1G
1A
1E
1C
1F
1I
2
3
4
5
1
6
1
2
3
4
5
6
(Sessile)
500 ppm/3 hours
500 ppm/6 hours
500 ppm/6 hours
> 500 ppm/6 hours
>> 500 ppm/6 hours
>> 500 ppm/6 hours
A single pass of a stiff nylon brush was the most gentle of the treatments, probably
relating to use of a foam pig in a real system. Even this minimal treatment reduced the
biofilm population to 4.5 x 102 GAB, 1.5 x 103 GAnB and 1.5 x 102 SRB per stud, a reduction
of 1 or 2 orders of magnitude.
A more aggressive treatment with a wire brush produced even better results, with
residual populations of 1.5 x 102, 9.5 x 101 and 9.5 x 101 GAB, GAnB and SRB respectively.
This treatment would reflect the use of a wire brush pig in a pipeline, and the results
demonstrate the dramatic cleanup effects of such a treatment. Reductions were in the region
of 3 orders of magnitude for all 3 microbial groups tested, and very low residual microbial
populations were left on the surface of the cleaned steel.
Finally, vigorous use of a sterile stiff plastic scraper resulted in the most effective
removal of biofilm. Only 7 GAB, 7 GAnB and 75 SRB per stud remained after this
treatment. These numbers can be considered to be insignificant and the conclusion must be
that this treatment effectively removed all the biofilm, leaving only a few bacteria in
inaccessible micro-environments. Such treatment probably equates to the use of a combined
brush/scraper pig in the field.
Although the trial could not be carried out on long-term corroded surfaces (which would
be more difficult to clean by mechanical means), the results demonstrate that mechanical
removal, if practised regularly and frequently, would be an effective biofouling/microbially
induced corrosion preventative measure. This would be particularly true if pigging was
combined with chemical biocide treatment. Under normal circumstances, a biocide treatment
would be used to kill those bacteria easily accessible on surfaces and to loosen biofouling
deposits. The mechanical scraper (pig) would then be used a few hours later to complete the
removal process, perhaps followed immediately by a second biocide slug.
CASE HISTORY 2: AQUIFER/EFFLUENT WATER INJECTION SYSTEM, SOUTH
KUWAIT
This was another mixed water injection system, this time with sulphide in all of the
streams. A more limited test program was deemed adequate given the low biofouling
measured in the field and the laboratory.
Three separate waters were tested:
Eight biocides were submitted for testing; the products were pre-screened in the vendors
laboratories for tolerance to sulphide and salinity (see Table 3).
The testing in this case was undertaken at the suppliers dosages, on fouled studs from
SBMTs. Bacteria from the system were used to inoculate the SBMTs, one SBMT being set
up for each water chemistry.
Aquifer A
The aquifer water was very highly saline and contained very low bacterial numbers
during the site analysis. Bacteria were only detected when 100 ml of water was filtered; the
low numbers are due to
2A
2B
158
Formulation
Biguanidine + QAC
Aldehydes
Suppliers
Recommended
Dose/contact time
500 ppm/3 hours
500 ppm/3 hours
Sanders et al.
2C
2D
2E
2F
2G
2H
(c) Case History 3
Biocide
3A.1
3A.2
3B.1
3B.2
3C.1
3C.2
3D.1
3E.1
3E.2
Formulation
Aldehydes
Aldehydes + amines
Aldehydes + amines
Glutaraldehyde + QPC
Fatty amines
Aldehydes + QAC
Formaldehyde + QAC +
QPC
Aldehydes
Aldehydes + QAC
Suppliers Recommended
Dose/contact time
700 ppm 3 hours/week
700 ppm 3 hours/week
1000 ppm 4 hours/2 weeks
1000 ppm 4 hours/2 weeks
250 ppm 4 hours/week
250 ppm 4 hours/week
600 ppm 4 hours/week
200 ppm 4 hours/week
200 ppm 4 hours/week
Given the low biofouling population, it is not surprising that most biocides worked well,
reducing numbers to zero. For the sweet system, the ranking for the aquifer water (Aquifer
A) was
2H = 2G = 2E > 2C = 2B,
and for the sour system, (140 ppm sulphide), the ranking for the aquifer water was
2G = 2A = 2F > 2D > 2H
These rankings are based upon very small differences in performance.
Effluent B
The effluent SBMTs blackened due to the production of sulphide by SRB, but SRB
growth and biofouling was slow. Bacteria were present in the system in moderate numbers.
However, the salinity of the water was high (76,000 TDS), which would have reduced the
growth rate of any bacteria.
GAB were easier to kill then were SRB in this system. This is unusual (GAB are usually
more resistant to biocides in biofilms than are SRB) and suggests that an active biofilm was
not present on the studs. This was probably due to the combined effects of high salinity and
residual corrosion inhibitor from the site water.
Given the very low initial biofouling population, the rankings of the biocides were as
follows. For the sweet (no sulphide) situation in the effluent water (effluent B):
2H > 2G = 2E > 2C = 2B,
159
and for the sour water (250 ppm sulphide) situation in the effluent water (Effluent B):
2H > 2G > 2F > 2A > 2D
As for aquifer A, the bacterial numbers were very low, and the differences between the
biocides were minor.
Mixed Water
This water appeared to be the worst case from a biofouling point of view. This was
likely to be due to the addition of sulphate to the aquifer water from the effluent water, the
dilution of the aquifer's high salinity, and the dilution of possibly biostatic corrosion
inhibitors from the effluent water.
Control numbers of 300-650 GAB and 115-450 SRB per stud were recorded on this
SBMT, and most biocides reduced numbers substantially. As with other SBMTs, GAB were
reduced more than SRB, suggesting that a coherent biofilm did not form on the studs. Most
biocides performed better in the sweet tests than in the sour tests, suggesting that many
biocides initially acted as sulphide scavengers, thus reducing the effective biocide
concentration.
For the non-sour tests (no added sulphide), with mixed water C (mixed effluent and
aquifer) the biocide ranking was
2H > 2C > 2G > 2E > 2B
and for the sour tests (sulphide added at 220 ppm), with water C (mixed 2H/effluent/aquifer),
the biocide ranking was
2H > 2G > 2D > 2F > 2A
CASE HISTORY 3: SEAWATER INJECTION SYSTEM, NORTH KUWAIT
This is a conventional seawater injection system and, in this case, dynamic trials were
undertaken by injecting alternate biocides directly into the pre-fouled, recirculating SBMTs.
One SBMT was used for each combination biocide treatment. Formulations of the biocides
are shown in Table 3.
Biocides were dosed to the other 5 SBMTs over a 4 week period, steadily increasing the
dose from 50% to 100% of the manufacturers recommended dose concentration, retaining the
recommended frequency and dosage time. In all cases, a pronounced saw-tooth effect was
evident, with bacterial numbers recovering rapidly once the biocide was removed from the
system. This saw-tooth effect is regularly seen in such trials and in field monitoring of water
injection systems. Biocides tend to kill only a proportion of the bacteria present in biofilms,
and the survivors rapidly grow to re-form the active biofilm. This confirms the need to dose
biocide frequently in order to keep sessile bacterial populations at a low level.
Biocide Regime A
Both biocides were each dosed up to 700 ppm of the product for 3 hours once per week
(i.e., two biocide treatments each week). Biocide 3A.1 was an aldehyde mixture that did not
foam, whilst 3A.2 was a mixture of aldehydes and amines that did form foam when agitated.
160
Sanders et al.
At half the recommended dose (350 ppm), biocide 3A.1 did not perform well, but
biocide 3A.2 reduced bacterial numbers to ca 103 per stud. At three-quarters of the
recommended dose (525 ppm), biocide 3A.1 was more effective, particularly against SRB,
but biocide 3A.2 was only marginally more effective. At 90% of the recommended dose (630
ppm), biocide 3A.1 reduced numbers to 104 per stud while biocide 3A.2 reduced numbers to
102-103 per stud. At 700 ppm, biocide 3A.1 reduced bacterial numbers to 103 per stud, and
biocide 3A.2 reduced them to 101 to 102 per stud.
Bacterial numbers appear to recover rapidly (within a few days) after all the biocide
doses. After the 75% dose of biocide 3A.2, however, numbers did not recover to their
original level: 104-105 cells of each bacterial type were present compared to 106 per stud in the
early stages of the trial. The data indicate that 3A.2 (containing an amine) was particularly
effective at 630 ppm and above, and that 3A.1 above 525 ppm was able to support the effects
of 3A.2. Continued treatment at 630-700 ppm with this biocide regime would be likely to
maintain (and probably substantially reduce) sessile bacterial populations under these
conditions.
Biocide Regime B
These biocides were dosed only once per week with the recommended concentration
being 1000 ppm; 3B.1 was an aldehyde and amine blend dosed for 4 hours, 3B.1 was a mixed
glutaraldehyde and THPS blend, again dosed for 4 hours. Biocide 3B.1 was strongly foaming
whilst biocide 3B.2 did not foam when agitated. This once-per-week treatment gave good
kill of all 3 bacterial types at 750 ppm (106/stud was reduced to 102-103 per stud), but within a
few days the initial bacterial population levels were reestablished. There appears to be no
significant difference in the data from the 1000 ppm dosing regime as compared to the 750
ppm dosing regime for GAB and GAnB (numbers were reduced to 101-103 per stud). Data
from the Regime B trial indicated that one biocide dose per week is insufficient, and that 750
ppm for 4 hours is as effective as 1000 ppm for 4 hours.
Biocide Regime C
The biocides were dosed twice per week. Biocide 3C.1 was a fatty amine (250 ppm, 4
hours) and biocide 3C.2 was an aldehyde/QAC mixture (250 ppm, 4 hours). Both biocides
formed foam when agitated, so they would not be suitable for dosing upstream of a deaerator
tower.
Biocide 3C.1 was very effective against GAB, GAnB and SRB;: even at 125 ppm,
bacterial numbers were reduced from 106 to 102-103. Above 187 ppm, 3C.1 reduced numbers
even further, in some cases to below 10 cells per stud. Biocide 3C.2 was, however, less
effective. Even at 250 ppm, numbers were reduced by only 1 or 2 orders of magnitude.
Despite the relatively poor performance of biocide 3C.2, however, there was a general
downwards trend in bacterial numbers over the course of the trial and continuation with such
a regime would probably lead to effective microbiological control. The most effective
biocide in this case appeared to be 3C.1. Biocide 3C.2 could be improved by increasing the
dosing concentration or changing to an alternative type.
Biocide Regime D
This vendor chose to submit only one chemical for testing, at a recommended dosing rate
of 600 ppm for 4 hours once per week. The biocide was a complex blend of formaldehyde,
161
QAC and THPS. It formed foam when agitated, and thus, might only be dosed downstream
of a deaerator tower.
At 300 ppm, bacterial numbers were reduced to 103 per stud, but at 450 ppm they were
reduced to only 104. At 540 - 600 ppm, bacterial numbers were reduced to between 102 and
103 per stud, but only transiently. There was no apparent downwards trend in the data, and
effective microbiological control did not seem to have been imposed by this regime, probably
due to the infrequency of dosing.
Biocide Regime E
Regime E biocides were dosed twice per week. Biocide 3E.1 was a mixture of
aldehydes, dosed at 200 ppm for 4 hours, while biocide 3E.2 was an aldehyde/QAC blend,
again dosed at the recommended 200 ppm for 4 hours once per week. Biocide 3E.1 did not
foam and thus could be dosed upstream of deaerator towers, whilst biocide 3E.2 did form
foam and so would only be suitable for dosing downstream of such a tower.
This biocide regime was particularly ineffective (apart from some transient reduction in
SRB numbers early on). No consistent reduction in bacterial numbers was observed over the
course of the treatment. Even if the concentration of the products were increased, effective
control could not be guaranteed. The ranking derived from these trials is given in Table 4.
Least Effective
Regime C
Regime A
Regime B
Regime D
Regime E
CONCLUSIONS
It is clear from this trial that one biocide treatment per week is insufficient to achieve
good kill of biofilm bacteria. The data clearly show that two doses per week of an effective
chemical can give good control of a well established biofilm. Such dosing would also
minimize the buildup of biofilm in the first place if implemented from the startup of the
system.
In order to assess the suitability of any biocides for the system, other factors must be
taken into account:
1. System demand. Sufficient residual biocide must be present at the end of the
water distribution system to exert control there. A higher dose may be
required at the main treatment plant to ensure that the minimum effective
concentration is maintained at the system extremities, if there is a significant
162
Sanders et al.
6.
7.
8.
9.
A.K. Tiller, Aspects of microbial corrosion, In Corrosion Process, R.N. Parkins Ed.,
Applied Science, 1982, pp. 115-160.
W.A. Hamilton, Sulphate-reducing bacteria and anaerobic corrosion, Annual
Reviews of Microbiology 39, 1985, pp. 195-217.
G. Kobrin (Ed), A Practical Manual on Microbiologically Induced Corrosion, NACE,
1993.
G.H. Booth, Microbial Corrosion, M & B Monograph CE/1, Mills & Boon, 1971.
P.F. Sanders and D.L. Robinson, Corrosion control using continuous residual
chlorine, In Microbial Corrosion (Proceedings of the 2nd European Federation of
Corrosion Workshop on Microbially Induced Corrosion), European Federation of
Corrosion, Publication No. 8, Institute of Materials. C.A.C. Sequeira and A.K. Tiller
Eds., 1992, pp. 198-209.
P.F. Sanders, Monitoring and control of sessile microbes: Cost effective ways to
reduce microbial corrosion, In Microbial Corrosion 1, Elsevier Applied Science,
C.A.C. Sequeira and A.K. Tiller Eds., 1988, pp. 191-223.
W.J. Georgie, P.I. Nice and S. Maxwell, Selection, optimisation and monitoring of
biocide efficiency in the Statfjord water injection systems, In UK Corrosion 91,
1991.
I. Ruseska et al., Biocide testing against corrosion causing oilfield bacteria helps
control plugging, Oil and Gas Journal 80, 1982, pp. 253-264.
P.F. Sanders and L. Latifi, On-site evaluation of organic biocides for cost-effective
control of sessile bacteria, In Proceedings of the Second International Conference on
Chemistry in Industry, American Chemical Society, Vol. I, Paper O-30, 1994, pp
242-257.
163
10. Review of current practices for monitoring bacterial growth in oilfield systems.
CCEJV 1987. Document number 001/87. Corrosion Control Engineering Joint
Venture, CCEJV, UK.
11. J.W. Costerton and G.G. Geesey, Microbial contamination of surfaces, In Surface
Contamination (1),. K.L. Mittal Ed., Plenum Pub., 1979, pp. 211-222.
12. P.F. Sanders, Rapid methods for detecting microbial corrosion, In Proceedings of UK
Corrosion 92, Volume 3, Session D. Institute of Corrosion, 1992.
13. Review of current practices for monitoring bacterial growth in oilfield systems, 1987,
Document No. 001/87, Corrosion Control Engineering Joint Venture CCEJV/NACE.
14. P.F. Sanders, Control of microbiologically induced corrosion using field and
laboratory methods. International Biodeterioration 24, 1988, pp. 239-246.
15. P.F. Sanders and J.F.D. Stott, Assessment, monitoring and control of microbiological
corrosion hazards in offshore oil production systems. NACE Corrosion 87. Paper
No. 367, 1987.
164
ABSTRACT
Following aqueous surface electrochemical reactions and hydrogen reduction, atomic hydrogen will
diffuse through steel, to reside at the microstructural defects with possible catastrophic failures to follow.
Carbon steel, low alloy steel or high strength low alloy steel under no-load, static or cyclic loading will be
affected by the presence of hydrogen. Such an effect is mainly influnced by temperature, alloying,
residual and applied stress, and partial pressure of hydrogen.
Permeation tests were conducted by Devanathan's electrochemical method and a newly invented
electro-vacuum method. Experiments illustrated that as the microstructure changed the diffusion constant,
D, changed. Ingress of hydrogen increased with the reduction of voltage and pH. Thickness would not
have a realistic effect, but cold work reduced D. The difference in D measured by the two methods of
permeation was due to the variation in material, apparatus design and operation.
Hydrogen degradation during stress corrosion and corrosion fatigue tests is one of the two processes
of crack propogation. Immersion, dynamic polarization, stress corrosion (dynamic and static), corrosion
fatigue tests, cathodic protection and fractographic studies were conducted in seawater and sour (hydrogen
sulfide generated by sulfate reducing bacteria) environments. In all, it was concluded that with regards to
Nernest's equation, as the partial pressure of hydrogen increased, the hydrogen concentration gradient
(Fick's first law) increased and D increased. Furthermore, the speed of hydrogen diffusion increased. In
the sour environment, the overtaking mechanism of failure was found to be hydrogen embrittlement rather
than anodic dissolution.
Key Words:
INTRODUCTION
The sources of hydrogen production in the industry are many:
water dissociation
+
H 2 O H + OH
(1)
Fe-H2O reaction
2Fe+ 3 H 2 O
(2)
+
H +e H
(3)
165
After atomic hydrogen production at the cathodic side of a corrosion cell, hydrogen will diffuse
into steel residing at the lattice interstitial sites, grain boundaries, vacancies, impurities and
alloying elements. The bonding energy of such interactions is different (see Fig. 1 and Table 1).
Trap sites are either low energy reversible (e.g., interstitial solutes 3-15 KJ/mol [1]) or high
energy irreversible (e.g., TiC particles 96 KJ/mol [1])
It is believed that steels with high energy traps will release hydrogen at about 2500C and at
higher temperatures. Generally, hydrogen will not saturate and therefore is less likely to damage
the austenitic stainless steels, but carbon steel, and ferritic or martensitic steels will be degraded,
and finally cracked.
Table 1. Trap Energy [1]
Trap
Interstitial Solutes (C, N)
Si Atom
Ti Atom
Vacancy
Y Vacancy
Dislocation Elastic Stress Field
Dislocation Core (Screw)
Dislocation Core (Mixed)
1/2 H2 (Vapour /Liquid)
Grain Boundary
Free Surface
AlN Interface
Fe3C Interface
TiC Interface
EB (KJ/mol)
NT (m-3)
~3-15
>20
26
46
126
20
20 - 30
59
29
~59
70 - 95
65
84
96
1025
1027
1027
<1023
1023
19
10 - 1026
1019 - 1026
1019 - 1026
--19
10 - 1023
1021
24
10 - 1025
1024 - 1025
1024 - 1025
Farzam
Hydrogen embrittlement,
Hydrogen blistering,
Hydrogen induced cracking.
As little as H<1 ppm is enough to damage steel. Figure 2 shows a 20"-oil line pipe
(Cheshmeh Khosh) damaged by hydrogen blistering.
Pressure theory,
Surface energy,
Enhanced plastic flow,
Transport model,
Hydride formation,
Decohesion theory.
Since the diffusion of hydrogen into austenitic stainless steel will not increase the internal
gas pressure, the pressure theory cannot be generally applicable. As far as the surface energy
theory is concerned, as the oxygen absorption at the surface will not reduce the surface energy
(with higher adsorption energy than H), this theory may not always be applicable. The third
theory, which discusses the enhancement of plastic deformation in the presence of H, has rarely
been approved and reported. The fourth theory describes hydrogen transportation by dislocations,
but in the absence of dislocations, hydrogen will also diffuse and be transported. There is an
interaction of hydrogen with alloys such as Nb, e.g., Nb-H which is a brittle compound (the fifth
theory). Such an effect cannot also be a prime factor of degradation.
167
It is generally believed that the last theory; decohesion theory, is the major responsible
factor weakening the Fe-Fe bonds, and that a hydrogen failure is a result of the participation of all
six theories.
The temperature at which hydrogen will inflict its severest damage is at about 25oC [2].
Figure 3 shows that the crack advance at this temperature is maximum. The figure also shows
that the higher the steels strength, the faster the crack propagation rate. The effect of hydrogen
when coupled with static and cyclic stresses will be reflected as stress corrosion, corrosion
fatigue or a combination of the two, i.e., stress corrosion fatigue [4].
The hydrogen diffusion characteristics previously reported by Devanathan and Stachurski
[5] (Fig.4) showed that it takes an incubation period tb before hydrogen reaches the exit surface.
The amount of hydrogen reaching the exit side increases and reaches a steady-state with time.
Time tb and the area under the curve are representative of the metals characteristics.
Farzam
dc
dx
(4)
where J is the flux in mol/cm2S, D is the diffusion constant in cm2/S, C is the concentration in
mol/cm3 and X is the distance hydrogen travels in cm.
D = D0 exp
Q
RT
(5)
where D is a constant, Q is the activation energy in J/mol, R is the gas constant in J/mol K and T
is the temperature in K.
It has been shown experimentally that:
2
D=
L
6t lag
(6)
where L is the thickness in cm and tlag = 0.63 J steady-state. From Fig. 4, tlag is measured at the
intersection of the vertical line with the tangent of the slope at 0.63PS.S.. Some researchers [6]
have used the 0.83PS.S.. Devanathan and colleagues [5] showed that as the voltage decreased, the
amount of hydrogen diffused increased and D was not a function of thickness. Detailed research
has been conducted on the effect of microstructure on hydrogen diffusion [7].
The concluding remarks on such an effect are that the structural inhomogeneities; line
defects, impurities (TiC) or martensitic laths, will trap hydrogen and degrade the microstructure.
The lower the hydrogen-defect bonding energy and the less such microstructural
inhomogeneities, the less the amount of trapped hydrogen and the less the likelihood of hydrogen
degradation. Table 1 shows the variation of such energies with defects. Other researchers have
reported their findings on the increase of the number of dislocations and therefore the amount of
trapped hydrogen and trapping energies [8,9]. Having a homogeneous structure reduces the risk
of hydrogen damage. Variation of D with microstructure and alloying is definite, and it may be
stated that the lower the D, the lower the amount of diffused hydrogen [10]. Therefore, if the
amount of trapped hydrogen is lowered, the possibility of hydrogen damage is decreased. It may
be suggested that by controlling the microstructure, hydrogen degradation is controlled.
Considerable research has been previously conducted on the fractography of fractured surfaces.
In a stress corrosion cracking study in H2S, Huang and Shaw [11] showed that the crack
morphology was quasi-brittle and the observed white markings were considered as a sign of the
presence of hydrogen.
EXPERIMENTAL PROCEDURE
Diffusion measurements have been either conducted by electrochemical charging [5] or a
dry gas technique [8]. In the electrochemical method, a steel sample is situated between an
anodic cell and a cathodic charging cell. When a potential difference between the two sides is
169
established due to the presence of hydrogen on the cathodic side, H diffusion takes place and
after awhile is detected at the anodic side. Hydrogen diffusion increases with time reaching a
maximum of a steady-state amount. As the negative charging potential is increased, the PS.S. is
increased (Nernest equ.).
This article represents more than ten years of reseach, beginning at Sheffield University
(U.K.) then at Heriot-Watt University (U.K.), and then in Iran. The electrochemical technique
was used at Sheffield, while a newly invented method which is a cross technique between the
electrochemical and vacuum (gaseous) techniques was employed in Scotland. The results were
then correlated with stress corrosion, corrosion fatigue, and case studies. Figures 5 and 6 show
the apparatus used in the present investigation.
170
Farzam
Mn
Si
0.079
0.089
0.13
0.13
1.33
1.38
1.57
2.23
0.29
0.31
0.32
0.31
S
0.004
0.031
0.007
0.01
P
0.006
0.005
0.008
0.008
Cr
Ni
0.11
-
0.15
-
The steel samples were Pd-plated and tested in caustic soda (0.1N NaOH) at potentials
lower than -1300 mV. During these tests, the effects of thickness, voltage and plastic
deformation (after 72% R.A) on variation in D were recorded. Table 3 shows some of the results
obtained.
Table 3. Results of Devanathan Test (0.1 N NaOH, 2 mm thick)
Material
API X-65 (Low S)
API X-65 (High S)
BS 4360
BS 4360 (Quenched)
tlag (min)
D (cm2/S X 10-6 )
68.75
77.5
69
253
1.61
1.43
1.61
0.44
Mn
Si
Cr
Ni
0.14
0.38
1.33
0.73
0.33
0.2
0.003
0.016
0.008
0.13
0.05
1.08
0.03
1.38
171
API 5LX - 52 steel may also be used to carry liquid gas or other petroleum products, and
AISI 4340 is used as a well casing material. Table 5 shows the results obtained in 0.1N NaOH
for these latter two steels.
Table 5. Results of Electro-Vacuum Test (0.1N NaOH, 2 mm Thick)
Material
tlag (min)
D (cm2/S X 10-7)
242
541
4.58
2.05
API X-52
AISI 4340
For the reason of an actual simulation, the steel samples were not plated in the latter tests.
During these tests, the effects of environmental change, thickness and voltage were examined
(see Table 6).
Two cases of fractured surfaces were compared with one another to find footprints of
hydrogen.
1. A case of stress corrosion fatigue of high strength steel cables that failed in H2S
environment,
2. Another case of stress corrosion fatigue of N.I.O.C drill pipes.
It is worth mentioning that other stress corrosion and corrosion fatigue tests were conducted
that are not all stated here. The stress corrosion tests were conducted either statically (80%Syield)
or dynamically (slow strain rate = 10-5 S-1). The corrosion fatigue tests were conducted at 0.167
Hz frequency and constant stress range. These latter tests were conducted on AISI l055, 1075,
and 50B60 in putrid seawater (H2S = 200 ppm) [14]. As the emphasis here is on the kinetics of
hydrogen diffusion rather than on fracture morphology, only a few fractographs are presented in
this paper. Some of the linear polarization, potential and pH measurements conducted on the
cables show the rate and possible change in the types of reactions. Immersion tests were also
conducted in the sour environment.
Table 6. Results of Electro-Vacuum Test (0.5mm)
Material
AISI 4340
AISI 4340
AISI 4340
API X-52
API X-52
API X-52
API X-52
Inh. : Inhibitor
H2S : Seawater + H2S
172
Environment
tlag (min)
D (cm2/S X 10-7)
0.1 N NaOH
Seawater
Seawater + Inh.
0.1 N NaOH
Seawater
H2S
H2S + Inh.
82
62
56
90
62
28
42.5
0.84
1.12
1.24
0.77
1.12
2.48
1.63
Farzam
Figure 7. Hydrogen diffusion measurements conducted by Devanathans method (2mm thick) (i)
X-65 (low S); (ii) X-65 (high S); (iii) BS 4360; and (iv) BS 4360 (Quenched)
-E = - E 0 +
RT
ln P H 2 - constant PH
ZF
(7)
As the thickness was decreased from 2 to 0.5 mm, D increased from 1.6 x 10-6 to 4.3 x 10-6
cm2/S. This change was only due to the kinetics of the electrodes surface. The electro-vacuum
173
tests conducted on API X-52 and AISI 4340 (Fig. 8) were made without Pd coating of the test
samples.
Published research has shown that the volume of hydrogen diffusing through would increase
with the increase in surface scratches as a result of the increase in surface area [12]. Thus, during
the present series of tests, all the samples were polished with 600 grade SiC paper and used
uncoated. Other investigators reported unsuccesful test results if the samples were not Pd-coated
[13]. In the present work, the measured D for X-52 was twice that of 4340. A comparison of the
alloying elements of the two metals indicates that AISI 4340 has a higher amount of C, Cr, Ni
and S. It is generally believed that elements on the right-hand side of Fe in the periodic table (C,
Ni, etc.) repel hydrogen while elements on the left-hand side of Fe (Cr, Nb, etc.) attract hydrogen.
A comparison of D values for the electro-vacuum tests with those of the electrochemical
experiments reveals that D was 10 times larger (faster) for the electrochemical tests. This is most
likely due to the surface impedance of the scales (absence of Pd) in addition to variations
resulting from the electro-vacuum test method. Table 6 shows that D changed with the changes
in the test environment. Testing AISI 4340 in 0.1N NaOH provided D = 0.84 x 10-7 cm2/s, which
is similar to that for API X-52. But when X-52 was tested in H2S, X-52, D increased from 0.77
to 2.48 x 10-7 cm3/S. Linear polarization tests conducted in H2S on AISI 1074 showed that FeS
resulted in cathodic depolarization (see Fig. 9). Thus, with the increase in cathodic reaction, the
amount of hydrogen reduction and diffusion would increase. This matches the results obtained
during diffusion (Table 6).
Farzam
Figure 9. Linear polarization (cathodic side) in: (1) seawater + H2S = 300 ppm; and (b)
3.5% NaCl solution
The free corrosion potential of a steel in the presence of H2S will change with time. Figure
10 shows that with time (after 219 h) the potential of AISI 1055 increased from -720 to -560 mV.
This may be due to the change in FeS stoichiometry, perhaps to FeS2. When the corroded surface
was cleaned, it was noted that pits had formed under the black FeS layer (see Fig. 11).
Figure 10. Changes in Ecorr in different H2S concentrations for AISI 1055
175
Farzam
REFERENCES
1. R. Gibala and A.J. Kumnick, Hydrogen trapping in iron and steels, in: Hydrogen
Embrittlement and Stress Corrosion Cracking, Ed., R. Gibala and R.F. Hehemann, ASM,
1984, p. 61.
2. H.H. Johnson, Overview on hydrogen degradation phenomena, in: Hydrogen
Embrittlement and Stress Corrosion Cracking, Ed., R. Gibala and R.F. Hehemann, ASM,
1984, p. 3
3. F.P. Ford, Stress Corrosion Cracking, in Corrosion Processes, Ed., R.N. Parkins, Applied
Science Publishers, 1982, p. 271.
4. J. Congleton and I.H. Craig, Corrosion Fatigue, Applied Science Publishers, 1982, p. 209.
177
178
Oil Plus Limited, Hambridge Road, Newbury, Berkshire, RG14 5TR, England
ABSTRACT
Thermophilic (high-temperature requiring) sulphate-reducing bacteria (tSRB) are responsible for
both corrosion of oil production facilities and souring of produced oil. During oil recovery, a range of
chemicals is injected into oil reservoirs for various operational reasons. Such chemicals may be
designed to inhibit microbial growth, or to specifically inhibit general corrosion. Other chemicals,
such as scale inhibitors, oxygen scavengers, H2S scavengers and surfactants, may be also injected. To
date, there is little published data on the effect of any of these chemicals on the micro-flora that is
known to exist in the oil formation.
The effect on sulphide production using a tSRB isolated from an oil bearing chalk formation was
monitored in the presence of rock surfaces and individual chemicals. The presence of a surface
increased sulphide production, whilst oilfield chemicals produced a variety of responses, from
complete inhibition to significant enhancement of sulphide production. Differences were observed
within the various classes of treatment chemicals. Some molecules appeared to break down more
easily than others under reservoir conditions and thus served to stimulate sulphide production. The
data obtained will help to manage oil reservoirs in a more cost-effective and environmentally friendly
manner, minimizing both sulphide production and microbial corrosion by determining appropriate
chemical selection and dosing regimes.
Key Words:
INTRODUCTION
The production of oil worldwide is adversely affected by the growth of bacteria,
particularly the sulphate-reducing bacteria (SRB). These may be mesophilic (mSRB),
growing optimally at 30C, or thermophilic (tSRB), growing optimally at 60C. Although
SRB are encountered in many anaerobic environments, their principal habitat is marine
situations, either in sediments or suspended in seawater, where sulphate concentrations are
high. SRB activity enhances corrosion of iron and steel in storage tanks, pipelines and
equipment as well as creating problems of toxicity and spoilage of the gas and oil. In the
reservoir itself, permeability reductions may be caused by growth of bacteria in the pore
spaces of the rock leading to reduced recovery efficiency [1-4]. Most attention has been paid
to mSRB growing in seawater treatment facilities, where biofilms containing mSRB are
responsible for enhancing the corrosion of steel [5]. Recently tSRB have been isolated from
179
oilfield reservoirs and production systems [6-8], with significant implications for maintenance
and integrity of hot oil production pipework and associated plants [9]. tSRB have also been
detected in injection water and open seawater [7,10], together with other thermophilic
heterotrophic bacteria, indicating the presence of widespread consortia of thermophilic
bacteria in these environments. Temperatures may reach 120C in some oil-bearing
formations [11], but are typically 80-100C. tSRB have been shown to grow or survive in
this range of temperature [4,7].
Actively growing tSRB readily attach to surfaces, assisted by the production of large
amounts of exopolysaccharide [12] and survive adverse conditions by the formation of
dormant cells which have been shown to retain viability for long periods of time [8]. These
dormant cells may pass through the reservoir rock since they are small and produce less
exopolysaccharide. They thus contaminate both the deep reservoir and the production
system. In some situations, even starved cells may attach to surfaces and form part of a
developing biofilm [13]. Biofilms containing tSRB and other thermophilic bacteria can thus
develop on rock surfaces as well as on metal surfaces. When such a biofilm develops on
exposed steel, corrosion can be initiated by the production of sulphide or organic acids [14];
when it forms within rocks, permeability reduction can occur.
Many microorganisms are able to survive wide and rapid variations in environmental
conditions. Renewed interest in the ability of microorganisms to survive low nutrient status
has prompted research into bacterial starvation responses [15]. Oil/water mixes produced
from reservoirs frequently contain tSRB as they enter topside facilities. Nutrient availability
in such situations will vary with the origin of the produced water; therefore, any tSRB in
these locations will be responding directly to nutrient stress as well as temperature shifts.
Some cells will adopt a starvation/survival mode which may take the form of reduction in cell
size with reduced levels of metabolic activity [7]. Additionally, cells adhere to available
surfaces [10] and subsequently form biofilms in topside production systems. The ability of
tSRB to switch between different growth states, depending upon the environmental
conditions, allowing the bacteria to survive extreme or adverse conditions has been described
[11]. This, in turn, means that reservoir sulphide souring and corrosion in high temperature
systems will be encouraged if a change to more favourable conditions occurs.
Biofilms (consisting of vegetative, active, tSRB and other thermophilic anaerobic
bacteria) developing in hot oil production systems will give rise to increased sulphide
production, which may eventually lead to significant souring of the produced fluids [17]. In
addition, the activity of thermophilic bacteria on hot metal surfaces will lead to an increase in
microbially influenced corrosion (MIC) due to the local production of corrosive metabolites
such as sulphide and organic acids [9,18,19].
The studies described in this paper are part of an ongoing investigation into the survival
and activity of tSRB in oilfield reservoirs. A wide range of tSRB was enriched and isolated
from a series of surveys on and around North Sea installations. Samples included raw
seawater, injection water, well-head samples, production separators and overboard discharge
lines at three major oil field production/injection facilities. These isolates were used to
conduct a series of laboratory trials related to the control of reservoir souring and associated
corrosion implications. Particular emphasis was placed upon the relative importance of
starved, dormant (non-sulphide-producing) growth states, the active (sulphide producing)
180
Sanders et al.
vegetative state, and the availability of surfaces and chemical treatments on sulphide
generation rates.
METHODS
Thermophilic Sulphate-Reducing Bacteria Cultures
Two oilfields were selected for the isolation of high-temperature, hydrogen sulphideproducing bacterial enrichments. Both fields had fractured chalk reservoir rock, and were
experiencing seawater breakthrough and increasing hydrogen sulphide concentrations in the
produced fluids. Two consortia (EX251 and EX258) from hot oil producing systems were
studied for their tolerances to chemicals and reactions to surfaces.
Growth Media
Three anaerobic media selective for SRB were prepared: MCP, EX2 and SWM.
MCP is a modification of Postgate's E. It contained Na lactate (70% w/w solution 12.5 ml 11
), Na acetate (50 g l-1), Na propionate (1.0 g l-1), and Na butyrate (0.4 g l-1) with NaCl (25 gl1
). EX2 contained KH2PO4 (0.4 g l-1), NH4Cl (1.0 g l-1), CaCl2 (0.1 g l-1) MgSO4.7H2O (2.0 g
l-1) FeSO4.7H2O (0.5 g l-1), yeast extract (1.0 g l-1), Na2SO4.2H2O (1.0 g l-1), NaHCO3 (2.4 g l1
), Na pyruvate (6.0 g l-1) and NaCl (25.0 g l-1). SWM was used when a clear medium was
required. Na pyruvate (6.0 g l-1) and yeast extract (oxoid, 1.0 g l-1) was added to one liter of
artificial seawater solution (ASW). After these additions, the prepared medium was sterilized
by filtration (with Whatman's presterilized cellulose acetate filter, 0.45 mm pore size) and
dispensed in presterilized bottles in an anaerobic cabinet.
Spectrophotometric Sulphide Assay
The micro method described here is a modification of those described by Truper and
Schlegel [20] and relies on the liberation of sulphide by acidification and subsequent
development of methylene blue from n,n-dimethyl-p-phenylene diamine sulphate.
Influence of Surface Area on Sulphide Production
This experiment was designed to determine whether the area of available surface in a
culture vessel exerted an influence on the amount and rate of sulphide production of a culture
of tSRB cells. Culture EX251 was selected for this experiment. Several sets of four injection
vials were set up containing 0 (control), 0.01, 0.1 and 1 g of washed Bunter sand with 9 ml of
SWM. Each vial was inoculated with one milliliter of a three day old culture of EX251 and
incubated at 60C. At predetermined sample times, three vials were removed from each
treatment set and sampled for sulphide production and metabolic activity.
Sulphide Production from EX251 in Long Term Contact with Oil Formation Rock
Chalk core chips were distributed in 15 g quantities in a series of presterilized, loosely
stoppered injection bottles and placed in an oven at 110C for 36 hours. The bottles were
placed in an anaerobic cabinet overnight to deoxygenate the rock pore spaces. EX251 was
inoculated as follows: sterile, full strength SWM, 1/10 strength SWM (diluted with ASW)
and ASW. 1/10 strength SWM was added to the uninoculated control. Each bottle was crimp
sealed to maintain the anaerobic status of the contents and then incubated at 60C. Samples
were withdrawn at intervals over several months for sulphide assay.
181
Sanders et al.
observed in the control bottles containing only chalk chips and SWM/10 medium. The
sulphide production is plotted against time in Fig. 2 for each of the nutrient treatments given
to the EX251 cells in contact with the chalk. In the bottles with SWM at full strength, there
was a rapid increase in sulphide concentrations in the first two days, similar to the previous
experiment. This was followed by further increases over the ensuring four weeks until the
maximum assayed sulphide was 100 ppm. The concentration of sulphide then steadily
diminished to 55 ppm over a period of six months. Extra nutrient was added at the start of
week 34, and sulphide measurements continued. Due to dilution caused by the added
nutrient, the sulphide concentrations were reduced immediately after the fresh nutrient was
added; however, within two days, the SWM cultures showed renewed sulphide production
which peaked at 60 ppm within ten days of the extra nutrient being supplied.
Figure 1. Sulphide produced from EX251, grown in the presence of 0.01, 0.1
or 1 g sand compared with a control containing no additional surface. n = 3;
all error bars displayed (+/- SE of mean). At 54 h, p < 0.05 for 1 g sand
treatment and by 102 hours all sand treatments were significantly different
from the control (p < 0.01)
When SWM/10 was added to the bottles, there was a discernible increase in sulphide
output in the first three to four weeks; the maximum sulphide concentration achieved was 20
ppm and thereafter remained at about 15 ppm until the nutrient addition at week 38. After an
initial drop in assayed sulphide to 10 ppm, the sulphide concentration again rose in the
following ten days to 15 ppm, and as in the first part of the experiment, gradually declined.
183
In the experiments where cultures were offered ASW only, low levels of sulphide (c. 10
ppm) were observed when in contact with the chalk chips until the 36th week. The final two
readings, taken at 37 and 38 weeks, showed a reduction in assayed sulphide to 6 and 3 ppm
respectively. No sulphide was detected in the control series without added bacterial culture.
Figure 2. Long term survival and sulphide generation from cells of EX251
on oil-bearing chalk chips. Sulphide produced consistently available
nutrient at start of experiment. After further addition of nutrient at 34
weeks, renewed sulphide generation occurred. Results plotted are the
average of duplicate readings from two separate experimental vessels in
each case
Both cultures EX251 and EX258 secreted extracellular polysaccharide which aids
attachment to surfaces [12,21]. The presence of exopolysaccharide in corrosive biofilms on
metal surfaces containing SRB from Brazilian oilfield waters has been demonstrated by
ruthenium red staining techniques followed by electron microscopy [22]. Similar procedures
used in the authors laboratory have demonstrated the presence exopolysaccharide secretion
by tSRB.
The implication of the results is that thermophilic reservoir SRB reduce sulphate more
efficiently when attached to a surface such as sandstone, chalk or metals. Work by
Laanbrook and Geerlings [23] demonstrated an increase in sulphide production by SRB
cultures when clay particles were incorporated in the growth media. Other studies, on nonsubterranean mSRB taken from paddy fields and lake sediments, have suggested a
physiological advantage for bacteria attached to particulate material in sulphate deficient
situations [24]. It is also possible that attached cells were disadvantaged due to a reduction of
cell surface area available for solute transport at the physical points of contact in non-sulphide
limited conditions. This conclusion does not agree with other researchers [14, 25] who have
consistently reported the advantageous properties of commensal biofilm habitats. However, it
is clear from the work described here that there are factors affecting the metabolism of
sulphide-generating organisms in biofilms which have yet to be fully examined.
184
Sanders et al.
185
Corrosion Inhibitor
Filter Aid
Oxygen Scavenger
Produced Water
Polyacrylamide
Polyglycol
Phenol formaldehyde
alkoxylate
Polyol
Polyamine
Oxyalk phenolic + PAG
Oxyalk phenolic
Anthroquinone
QAC
Isothiazolone
THPS
Glutaraldehyde
Antifoam
20
20
20
10
2-10
10
30
20
2-4
Continuous
100-400
100-400
Drag Reducer
Dispersant
20
7
14
Deoiler
Demulsifier
Biocide
20
20
70
Fatty acids & esters
(intermittent)
Silicones in HC
20
20
186
Sanders et al.
187
Glutaraldehyde showed a similar pattern of sulphide generation, but in this case, control
appeared to be less effective, and sulphide concentrations were higher than in the control after
two to three day period (Figs. 7-10). These results emphasize that under-dosing biocides can
lead to stimulation rather than reduction in the souring problem.
No effect on sulphide generation rates was seen when oxygen scavenger was used (Figs.
11-12). Although widely used in seawater injection systems for oxygen control, such
chemicals are thought to be unlikely to stimulate additional sulphide from SRB activity in the
formation.
Some surfactants (used in production systems) were effective as biocides against tSRB
(Figs. 13-14), and the use of produced water containing such compounds would exhibit a
good degree of microbiological control near the wellbore.
Corrosion inhibitors (added in seawater and produced water injection systems) showed a
wide range of effects on sulphide production by tSRB (Figs. 15-18). This is due to the variety
188
Sanders et al.
of active agents used in this class of chemical: phosphonate types appear to enhance sulphide
production, having no biocidal properties, whilst QAC formulations can act as very good
biocides.
The combined effects of chemical dosing can now be assessed with respect to the
potential for enhancing or depressing sulphide production by SRB.
ACKNOWLEDGEMENTS
We wish to thank Agip SpA, Chevron U.K. Ltd, Maersk Olie og Gas A.S., Nalco/Exxon
Energy Chemicals Ltd., the Saudi Arabian Oil Company and the UK Department of Trade
and Industry for their valuable support and help during this study.
REFERENCES
1.
B.N. Herbert and P.D. Gilbert, Isolation and growth of sulphate-reducing bacteria, in:
Microbiological Methods for Environmental Biotechnology, 1984, pp. 235-257.
2. W.P. Iverson and G.J. Olson, Problems related to sulfate-reducing bacteria in the
petroleum industry, in: Atlas R.M. (ed) Petroleum Microbiology, MacMillan
Publishing Company, New York, 1984, pp. 619-641.
3. B.N. Herbert, Reservoir souring. in: Hill Shennan, Watkinson (eds) Microbial
Problems in the Offshore Oil Industry, J Wiley and Sons Ltd, London, 1987, pp. 6372.
4. C.J. Bass, P.F. Sanders and H.M. Lappin-Scott, Starvation and survival of
thermophilic sulphate-reducing bacteria from North Sea oil reservoirs. in: Proc 6th
Int Symp Microbial Ecology, International Committee on Microbial Ecology
(ICOME), 1992, Paper C4-3-3.
5. W. Lee, Z. Lewandowski, P.H. Nielsen and W.A. Hamilton, Role of sulfate-reducing
bacteria in corrosion of mild steel: A review, Biofouling 8, 1995, pp. 165-194.
6. J.T. Rosnes, T. Torsvik and T. Lien, Spore forming thermophilic sulfate-reducing
bacteria isolated from North Sea oilfield waters, Appl Environ Microbiol 57, 1991,
pp. 2302-2307.
7. C.J. Bass, H.M. Lappin-Scott and P.F. Sanders, Bacteria that sour reservoirs: New
concepts for the mechanism of reservoir souring by sulfide generating bacteria, J.
Offshore Technol 1, 1993, pp. 31-37.
8. K.O. Stetter, R. Huber, E. Blochl, M. Kurr, R.E. Eden, M. Fielder, H. Cash and I
Vance, Hyperthermophilic archaea are thriving in deep North Sea and Alaskan oil
reservoirs, Nature 365, 1994, pp. 743-745.
9. P.F. Sanders, H.M. Lappin-Scott and C.J. Bass, Corrosion implications of
thermophilic sulphate-reducing bacteria in oil reservoirs, Proceedings UK Corrosion
94, Vol. 4, Bournemouth, 1994, pp. 116-127.
10. S. Walsh, H.M. Lappin-Scott, H. Stockdale and B.N Herbert, An assessment of the
metabolic activity of starved and vegetative bacteria using two redox dyes, J
Microbiol Methods 24, 1995, pp. 1-9.
11. M. Magot, C. Hurtevent and J.L. Crolet, Reservoir souring and well souring. in:
Progress in the Understanding and Prevention of Corrosion, 1993, pp. 573-575.
12. C.M.L. Cutinho, F.C. Magalhaes and T.C. Araujo-Jorge, Morphology of the surface
coat and extracellular matrix of sulphidogenic biofilms enriched in sulphate-reducing
189
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
190
bacteria involved in biocorrosion processes in the offshore oil extraction industry off
Brazil's coast, J. Gen Appl Microbiol 40, 1994, pp. 271-276.
H.M. Lappin-Scott, C.J. Bass, K. McAlpine and P.F. Sanders, Survival mechanisms
of hydrogen sulphide producing bacteria isolated from extreme environments and
their role in corrosion, Int Biodegrad Biodeterior 34, 1994, pp. 305-319.
W.A. Hamilton, Sulphate-reducing bacteria and anaerobic corrosion, Ann Rev
Microbiol 39, 1985, pp. 195-217.
H.M. Lappin-Scott, C.J. Bass and P.F. Sanders, Monitoring and detection of different
growth states of thermophilic SRB, In: Proceedings UK Corrosion 1992, Volume 3,
Session D, 1992.
A.S. Kaprelyants, J.C. Gottschal and D.B Kell, Dormancy in non-sporulating
bacteria, FEMS Microbiology Reviews 104, 1993, pp. 271-286.
R.Y. Morita, Review: The starvation-survival state of microorganisms in nature and
its relationship to the bioavailable energy, Experientia 46, 1990, pp. 813-817.
W.J. Cochrane, P.S. Jones, P.F. Sanders, D.M. Holt and M.J. Mosley, Studies on the
Thermophilic Sulfate-reducing Bacteria from a Souring North Sea Oil Field, Society
of Petroleum Engineers (SPE), European Petroleum Conference Paper SPE 18368,
1988.
M.J. Mosley, D.M. Holt, W.J. Cochrane and P.S. Jones, Laboratory studies on the
growth and activity of thermophilic sulphate-reducing bacteria in relating to the
colonisation and corrosion of steel surfaces at high temperatures, Proceedings UK
Corrosion 89, Blackpool, 1989.
H.G. Truper and H.G. Schlegel, Sulfur metabolism in Thiorhodaceae 1. Quantitative
measurements on growing cells of Chromatium okenii, Antonie van Leeuwenhoek J
Microbiol 30, 1964, pp. 225-238.
H.M. Lappin-Scott and J.W. Costerton, Bacterial Biofilms and Surface Fouling,
Biofouling 1, 1989, pp. 323-342.
C.M.L. Cutinho, F.C. Magalhaes and T.C. Araujo-Jorge, Ultrastructure of
sulphidogenic biofilms rich in sulphate-reducing bacteria causing corrosion in the
offshore oil extraction platforms off Brazil's Atlantic coast, J. Gen Appl Microbiol
40, 1994, pp. 227-241.
H.J. Laanbrook and H.J. Geerlings, Influence of clay particles (Illite) on substrate
utilisation by sulfate-reducing bacteria, Arch Microbiol 134, 1983, pp. 161-163.
M.S. Fukui and S. Takii, Survival of sulfate-reducing bacteria in oxic surface
sediment of a seawater lake, FEMS Microbiol Eco 73, 1990, pp. 317-322.
H.M. Lappin-Scott, J. Jass and J.W. Costerton, Microbial Biofilm Formation and
Characterization, SAB Technical Series, Vol. 30, Denyer, Gorman and Sussman
(eds), Blackwell Scientific Publications, 1993, pp. 1-12.
ABSTRACT
The combined effect of hydrogen sulphide, carbon dioxide and chlorides on the sulphide stress
cracking (SSC) behavior of several austenitic and duplex stainless steels was studied in high temperature
environments by using slow strain rate (SSR) tests and immersion tests of stressed specimens.
The initiation of SSC is considered to require the breakdown of the passive film whereby the
localized corrosion resistance can be related to the SSC resistance and to the pitting resistance equivalent
number (PREN) of an alloy. The evaluation of the usefulness of different PREN values showed that the
SSC resistance of a certain alloy can be evaluated by using the PREN values including the nickel content
of an alloy. According to the results, as the PREN values increase, the SSC resistance increases. In the
environments studied, the critical temperature for cracking of austenitic alloys having a PREN value under
45 was below 150C, and as the PREN value was over 70 the critical temperature for cracking was higher
than 150C. The nickel-based alloy having a PREN value of 140 was not susceptible to SSC even at a
temperature of 230C with high partial pressures for H2S and CO2. When the SSR test was used, brittle
behavior was observed in the duplex alloy having a PREN value of 56, even with small amounts of H2S in
the chloride environment.
Key Words: Alloy steels, stainless steel, corrosion, stress corrosion, cracking (fracturing),
petrochemical environments, oil fields, hydrogen sulphide
INTRODUCTION
Corrosion of steels in sour gas environments is a complex process involving many reactions
between the environment and construction materials producing different kinds of corrosion
products [1]. For passivating alloys, the reduction of sulphur is the most feasible cathodic
reaction that accelerates localized corrosion in cathodically reducible corrosion systems [2]. The
anodic dissolution has been observed to increase and the passivation of corrosion-resistant alloys
has been observed to retard significantly as the hydrogen sulphide content of the environment
increases [3]. Besides hydrogen sulphide, other chemicals appearing in the solution have to be
considered [4].
In sour wells, the oil and natural gas are often contaminated by hydrogen sulphide, the
content of which may vary from a few parts per million up to 30% [5]. In the presence of
191
hydrogen sulphide, the atomic hydrogen that is produced on the surface of the steel by the
corrosion reactions tends to enter the steel and cause embrittlement. This phenomenon is called
sulphide stress corrosion cracking (SSC). SSC susceptibility is enhanced by chlorides, and the
results obtained by Fliethmann et al. indicate that the cracking mechanism is a mixed mechanism
of hydrogen- and chloride-induced SSC [6]. Besides cracking, considerable general corrosion
can be observed due to presence of carbon dioxide that acidifies the mixture of brine and oil [5].
In order to optimize the SSC behavior of the austenitic and duplex stainless steels, the chemical
composition and the ferrite/austenite ratio have to be considered [7]. Also the microstructure,
hydrogen diffusion coefficients [8] mechanical properties, heat treatment conditions, grain size
and form of nonmetallic inclusions play an important role in the SSC resistance of construction
materials [9,10]. Thus, for reasonable assessment of the applicability of a duplex stainless steel
in a specific sour environment, it is important to consider practical experience and to use suitable
SSC test methods, both regarding the loading procedure and the environment [11,12].
Localized corrosion resistance is related to the chemical composition, and thereby, to the
pitting resistance number (PREN) of an alloy. The initial process of SSC can be the breakdown
of passive film [7,13] whereby the increase in the chromium and molybdenum content of the
alloys increases the passivity of the surface layer. However, it has been pointed out that the
ferrite phase of duplex stainless steels is richer in chromium and molybdenum than the austenitic
phase, and hence, the PREN of the austenitic phase seems to play a more important role in pitting
resistance, and hence, in SSC resistance of duplex stainless steels than the PREN of the ferrite
phase [7]. The SSC susceptibility of duplex stainless steels is also greatly affected by the
ferrite/austenite ratio, distribution and grain size. The threshold stress for SSC in simulated sour
environments has been observed to be highest at the -content of 40 to 45%, and an alloy with a
-content exceeding 80% is reported to have a high susceptibility to pitting and intergranular
corrosion [14].
To evaluate the SSC behavior of selected austenitic and duplex stainless steels in high
temperature H2S solutions, slow strain rate (SSR) tests and immersion tests of stressed specimens
were used.
EXPERIMENTAL PROCEDURE
Test Materials
The austenitic stainless steels investigated in this study were delivered by Outokumpu
Polarit Oy, and the duplex stainless steels and the two experimental powder metallurgically
produced alloys were delivered by Rauma Materials Technology Oy. The reference materials
selected were Nicrofer 6020, Nicrofer 5716 and Nicrofer 5923; they were and manufactured by
VDM Nickel-Technologies AG and delivered by Cronimo Co. The chemical compositions of
the test materials and their PRENs are presented in Table 1. PREN1, PREN2 and PREN3 reflect
the effect of alloying elements, and PREN number 4 correlates with the ferrite content in a
duplex alloy so that the higher the PREN4 value, the lower the ferrite content.
Test Equipment and Test Environments
The high temperature sulphide stress cracking studies were carried out by using the SSR
method with round tensile test specimens (Fig. 1) and U-bend specimens. To insure the stability
of the test environment during testing, the Materials Research Shuttle Laboratory facility was
used. The facility consists of a high temperature and high pressure autoclave with a room
192
temperature storage tank and a recirculation loop. The facility is also equipped with an
environment monitoring system to control the water chemistry of the autoclave. The facility is
assembled into a freight container (Fig. 2) that was transferred outside the laboratory facilities in
order to avoid any indoor leakages of hydrogen sulphide. The corrosion potential measurements
were carried out using an Ni/NiSO4 reference electrode, and the results are presented in the scale
of a standard hydrogen electrode.
Table 1. Nominal Composition of the Materials Used in the Study as Provided by the
Manufacturers
Material
POLARIT 725
POLARIT 757
POLARIT 774
POLARIT 778
DUPLOK 21
DUPLOK 22
DUPLOK 25
DUPLOK 26
DUPLOK 27
DUPLOK 27 PM
Inconel 625 PM
Nicrofer 6020
Nicrofer 57161
Nicrofer 5923
C
0.027
0.049
0.02
0.024
0.012
0.013
0.015
0.023
0.01
0.04
0.02
0.01
0.01
0.01
Si
0.41
0.49
0.55
0.4
0.6
0.53
0.43
0.2
0.28
0.38
0.51
0.13
0.05
0.12
Mn
1.45
1.51
1.46
0.46
0.58
0.52
0.62
0.72
0.52
1.16
0.32
0.17
0.37
0.15
S
0,001
0.007
0.001
0.001
0.008
0.01
0.008
0.01
0.008
0.005
0
-
P
0.034
0.029
0.015
0.019
0.032
0.033
0.03
0.03
0.032
0.022
0
0.005
0.005
0.005
Cr
18
17.1
20
19.8
20.7
23
24.5
26.2
27.1
25.9
21.6
21.8
19
22.5
Ni
8.6
10.6
24.7
21.5
8.3
6.1
6.4
7.6
7.9
6.6
Bal.
Bal.
Bal.
Bal.
Mo
0.019
2.51
4.48
6.15
2.8
3
3
2.95
3
3.3
8.2
8.5
15
14
Cu
0.18
0.16
1.67
0.79
1.25
0.19
1.45
0.68
2.5
2.1
0.06
0.06
0.08
0.01
Material
Al
Co Nb
Fe
N
PREN1 PREN2 PREN3 PREN4
POLARIT 725
0.001 0.17 0
Bal. 0.0565 20
35
30
POLARIT 757
0
0.21 0
Bal. 0.046 27
42
45
POLARIT 774
0.022 0.22 0
Bal. 0.0765 37
76
73
POLARIT 778
0.024 0.37 0
Bal. 0.21
47
72
79
DUPLOK 21
0.03 0.05 0.06 Bal. 0.05
32
42
49
-8
DUPLOK 22
0.02 0.1 0.02 Bal. 0.15
38
40
50
-10
DUPLOK 25
0.03 0.07 0.04 Bal. 0.14
39
42
52
-11
DUPLOK 26
0.02 0.07 0.02 Bal. 0.22
43
46
55
-9
DUPLOK 27
0.01 0.05 0.03 Bal. 0.24
45
47
57
-10
DUPLOK 27 PM 0.02 0.05 0.01 Bal. 0.25
45
44
56
-9
Inconel 625 PM
0.02 0.06 3.7 4
0
49
172
140
Nicrofer 6020
0.16 0.05 3.4 3
0
50
173
142
1
Nicrofer 5716
0.09 0.1 0.04 6.5
0
69
172
171
Nicrofer 5923
0.2
0
0.03 0.5
0
69
170
167
1
The tungsten (W) content of the alloy Nicrofer 5716 is 4%
PREN1 = Cr + 3.3 Mo + 32 N. PREN2 = Cr + 2 Ni + 1.5 Mo [15]. PREN3 = Ni + 1.2 Cr + 5.5
Mo [16]. PREN4 = Ni + 0.5 Mn + 30*(C + N) - 1.1*(Cr + Mo + 1.5 Si) + 8.2 [14]
193
The test environments were water-based deaerated solutions containing different amounts of
NaCl, H2S and CO2. The materials tested in each experiment and the test type are presented in
Table 2. Also given in Table 2, are the contents of the different species in each experiment and
the pH value of the test solutions. The exposing time of the U-bend specimens in test 1 was 100
hours and in test 2 it was 400 hours. After testing, the specimens were examined using an optical
microscope; the failures were reported. For failure cases, a fractographical inspection was
performed.
0.4
Rmin6.4
B
M8
Rmin6.4
0.03 A-B
M8
3.810.05
0.05 A-B
12.5
25.40.05
12.5
70
NaCl Temperature
[wt-%]
[C]
5
200
H2S
[bar]
8
CO2
[bar]
-
pH
3
20
150
3
4
5
6
25
20
20
20
230
93
93
93
70
20
0.5
0.1
50
35
40
85
2.5
2.7
2.6
4.2
Materials
Tested
POLARIT 725
POLARIT 757
DUPLOK 22
All in Table 1 except
Inconel 625 PM
Inconel 625 PM
DUPLOK 27 PM
DUPLOK 27 PM
DUPLOK 27 PM
Test
Type
U-bend
U-bend
SSRT
SSRT
SSRT
SSRT
RESULTS
In test 1, failures were observed in all of the alloys tested. In the austenitic alloys, the
fracture was brittle and intergranular. In the duplex alloy, the fracture partly followed the phase
boundaries between the ferrite and austenite faces, but mainly the fracture was transgranular and
brittle. The corrosion potential of all the alloys during the experiment was near -100 mV (SHE).
In test 2, failures were observed in the alloys POLARIT 725 and POLARIT 757. The
failure mode in these austenitic alloys was mainly intergranular, as observed in test 1. No
failures in the duplex alloys were observed despite clear general and pitting corrosion. Pitting
corrosion was observed in the duplex alloys having a PREN1 value smaller than 40. In the
austenitic alloys, no similar pitting corrosion was observed. The corrosion potential of all the
alloys during experiment was near -100 mV (SHE).
In test 3, no evidence of brittle behavior was found for Inconel 625 PM. The fracture was
ductile, and the elongation to fracture was 40% which corresponds to the elongation observed in
the SSR test conducted in a nitrogen gas reference environment.
In test 4, the fracture of the DUPLOK 27 PM specimen was brittle and transgranular. The
elongation to fracture was only 8%, and the reduction in area was 18%. In the reference test in
nitrogen gas, the elongation to fracture was 32% and the reduction in area 60%.
In test 5, the hydrogen sulphide partial pressure was much lower than in test 4. The fracture
was still brittle and transgranular. Also secondary cracking was observed (Fig. 3). The
elongation to fracture was 26%, and the reduction in area was 25%.
In test 6, the hydrogen sulphide partial pressure was still lower than in test 5. The fracture
was mainly brittle (Fig. 4), but ductile areas were also observed in the fracture surface (Fig. 5).
The initiation and the outermost circle of the fracture surface were brittle, whereas the center of
the fracture surface was ductile.
195
sulphides are stable in the environments studied, the failure cases of the austenitic alloys were
apparently related to the various nickel contents of the different alloys. The nickel contents of the
unfailed specimens were clearly higher than those of the failed specimens. Therefore, for
materials selection purposes, the PREN equations including the nickel content of alloys are
recommended for use in H2S-containing environments.
It is also known that the cracking resistance of duplex alloys is enhanced compared to
austenitic alloys having the same level of alloying elements and mechanical properties.
Normally the initiation and the growth of cracks in duplex stainless steels take place in the ferrite
phase of an alloy. In this case, however, the cracking was observed to grow not only in the ferrite
phase, but also in the austenite phase. This was probably due to the high contents of hydrogen
sulphide, and therefore high contents of hydrogen, in the test environments. In test 1, the duplex
alloy failed although the PREN1 value of the duplex alloys was much higher than that of the
failed austenitic alloys. The PREN2 and PREN3 values including the nickel content of the alloys
were, however, at the same level in all of the failed specimens. Therefore, the correlation
between the content of alloying elements and the SSC resistance was better with the PREN
values including the nickel content of an alloy. In test 2, the difference between the PREN2 and
PREN3 values was noted. The PREN2 value showed no difference between the failed austenitic
alloys and the unfailed duplex alloy. The PREN3 values of the failed austenitic alloys were
lower than the PREN3 value of the unfailed duplex alloy. Therefore, the PREN3 value is
recommended for evaluating the SSC resistance of austenitic and duplex alloys. The usefulness
of the PREN4 value correlating with the ferrite content of a duplex alloy could not be evaluated
in this study due to the small number of experiments with different duplex alloys.
The SSR tests showed that the SSR method is aggressive since brittle behavior was
observed in the DUPLOK 27 PM alloy having a PREN3 value of 56 even with small amounts of
H2S in the environment. The fracture surface of DUPLOK 27 PM was mainly transgranular and
mainly in the ferrite phase. The nickel-based alloy Inconel 625 PM was on the contrary resistant
towards SSC even at very high temperature with high contents of hydrogen sulphide, carbon
dioxide and chlorides in the environment.
CONCLUSIONS
In this work the evaluation of the corrosion and SSC behavior of several austenitic and
duplex stainless steels in hydrogen sulphide containing environments was made using the SSR
test method and U-bend specimens. According to the results:
1. When evaluating the SSC resistance of a specific alloy, the PREN values including the
nickel content should be used,
2. The PREN3 value, which did not over emphasize the effect of nickel, gave the best
correlation between the content of alloying elements and SSC,
3. The critical temperature for cracking of austenitic alloys having a PREN3 value under 45
was below 150C in aggressive H2S-containing environments,
4. The critical temperature for cracking of austenitic alloys having a PREN3 value over 70
was higher than 150C in aggressive H2S-containing environments,
198
5. A small decrease in H2S partial pressure had a greater effect on the SSC resistance of
DUPLOK 22 than bigger changes in the temperature and in the NaCl content of the
environment,
6. In the austenitic alloys, the fracture mode was mainly intergranular,
7. In the duplex alloys, the fracture occurred partly on the phase boundaries of the ferrite
and austenitic faces, but the fracture was mainly transgranular,
8. The nickel-based alloy Inconel 625 PM was not susceptible to SSC, even in extremely
aggressive H2S-containing environments,
9. SSR is an aggressive test method, and brittle behavior was observed in the DUPLOK 27
PM alloy having a PREN3 value of 56 even with small amounts of H2S in the
environment, and
10. As the hydrogen sulphide partial pressure was lowered to 0.1 bar, partly ductile fracture
was observed in the DUPLOK 27 PM alloy.
ACKNOWLEDGEMENTS
This study was financed by the Technology Development Centre of Finland, Outokumpu
Polarit Oy, Rauma Materials Technology Oy and VTT Manufacturing Technology. The authors
acknowledge these organizations for their financial support and for providing the test materials.
Also Cronimo Co. is acknowledged for providing the reference test materials.
REFERENCES
1. G.I. Ogundele and W.E. White, Some observations on the corrosion of carbon steel in
sour gas environments, Corrosion 42, 7, 1986, pp. 398-408.
2. A. Miyasaka, et al., Environmental aspects of SCC of high alloys in sour environments,
Corrosion 45, 9, 1989, pp. 771-780.
3. A. Miyasaka, et al., Prediction of critical environments for active-passive transition of
corrosion resistant alloys in sour environments, ISIJ International 31, 2, 1991, pp. 194200.
4. Z.A. Foroulis, Role of solution pH on wet H2S cracking in hydrocarbon production,
Corrosion Prevention & Control, August 1993, pp. 84-89.
5. R. Garber, et al., Sulfide stress cracking resistant steels for heavy section wellhead
components, Journal of Materials for Energy Systems, 1985, pp. 91-103.
6. J. Fliethmann, et al., Autoklaven-Untersuchungen der Spannungsribkorrosion von Fe-CrNi-Legierungen in NaCl/CO2/H2S-Medien, Werkstoffe und Korrosion 43, 1992, pp. 467474.
7. M.F. Brunella, et al., Stress corrosion cracking in sour environments of martensitic and
duplex stainless steels, Proceedings of International Conference on Stainless Steels,
Chiba, June 10-13, 1991. Tokyo 1991, ISIJ, Vol. 1. pp. 264-271.
8. Th. Bollinghaus, H. Hoffmeister and C. Middel, Scatterbands for hydrogen diffusion
coefficients in steels having a ferritic or martensitic microstructure and steels having
an austenitic microstructure at room temperature, Welding in the World 37, 1, 1996,
pp. 16-23.
199
200
ABSTRACT
The Amtliche Materialprfanstalt (AMPA) is an official materials testing institute and a
subordinate board of the Ministry for Economy, Technology and Traffic of Lower Saxony, which is a
federal state of the Federal Republic of Germany. The AMPA works in a lot of fields of materials
testing, quality testing, quality assurance and damage investigation. The special fields of the AMPA
include acceptance testing, supervision and inspection in the field of plant and pipeline construction
for natural gas and oil.
Because of this, the AMPA is often used by operators of pipelines or plants to give their expert
opinions in cases of damage. Two damage investigations will be given in this article. They are
damage to several pump linkages and damage to a tool-joint.
Key Words: Pump linkage, tool joints, damage investigation, acceptance tests, inspection
INTRODUCTION
Pump linkages and tool joints are used for pumping oil and gas from a depth of about
1,500 m in northern Germany. The pump linkages have lengths of about 6-10 m and
diameters of 7/8 in up to a depth of 400 m and 3/4 in beyond that depth. The pump linkages
reported here are directly connected. Because of tapping of different caverns from one
starting point, the drilling hole is often curved in to a horizontal drilling situation. The pump
linkages can follow these curves, because of their oscillating movement within the hole, the
linkages have proctection devices against mechanical damage made of plastic which are
placed at several defined areas along every linkage. The puming frequency is low-cycle and
depends on the length and weight of the equipment. The pumped medium is a mixture of
about 2% crude oil and 98% salty water.
These pump linkages are connected directly, whereas other pumping equipment uses tool
joints to connect their linkages. The tool joint has a length of about 0.5 m and a diameter of
about 0.2 m. The pumping rate is about 2,000 l/minute.
PUMP LINKAGE
The damaged pump linkages were made of 20 NiMo 8. These linkages can normally be
used for an operating time of about 18 months. For the case of damage in question, the pump
linkages broke after an operating time of 3-6 months. Operation was between 4,000 and
13,000 hours for at least 1.1-3.5 million oscillating units. All of them were broken at depths
201
of 500-1,000 m, so the broken linkages were 3/4 in diameter. These pump linkages were
broken directly beneath the connecting areas of the linkages.
Besides this, the mode of operation of pumping was changed. The frequency of
pumping was halved, which led to increased vibration in the pump linkages. The mechanical
stress on pump linkages is oscillating stress because of its own weight, and therefore, mass
inertia, as well as bending stress especially in the transition sections to more bend-stiff areas.
Further on, corrosion is caused by aggressive components within the pumped oil (salty water)
especially if the corrosion protective layer is damaged.
Visual inspection showed that there was no visible coarse surface damage. All breaks
were in transition sections to more bend-stiff areas of the pump linkage (Fig. 1) and looked
very similar to fatigue fracture or crack corrosion (Fig. 2). The corrosion protective layer was
not regular in terms of thickness of layers and showed small blisters on the surface (Fig. 3).
Within a metallographic inspection, a faultless purity and texture was noticed. The
pump linkages had no faults in the material and its texture. Near the surface, a slight
reduction of carbon content was visible (Fig. 4) as well as a rough surface in the base material
with detached corrosion protective layer (Fig. 5).
Testing of the mechanical and technological properties of the puming linkages disclosed
no faults. The required tensile strength and extension could be reached by all test samples.
Also the materials composition met the demands.
202
Kinzel
203
Figure 5. Rough surface of base material with a detached corrosion protective layer
(M 233415)
TOOL JOINT
The object of this investigation was a broken tool joint (7 3/8 in OD x 4 9/16 in ID, 5 1/2
in IF connector with 5 in drill pipe, grade G 105, Fig. 6). The built-in rope length was
3,600 m, the pumping rate was 2,000 l/min at a pressure of 180 bar, the coupled load was 160
tons, and the torque at top-drive about 41,500 N/m. The breaki was at a depth of 2,173 m and
occurred while clearing the hole. The linkage had been stored in open air from 1986 to
joining in 1995.
204
Kinzel
corrosion and fatigue fracture. Because of the low percentage of fatigue fracture area, it can
be concluded that the operation tension must have been high to break the tool joint.
206
ABSTRACT
The target of the present study is to analyse the possibility of soils, sampled along the routes of
gas mains laid without cathodic protection, to give rise to pipe metal stress corrosion cracking (SCC).
The tests included soils taken both on gas pipelines operated for 30 years without failure and on
pipelines that had failed due to SCC. The pipe steel specimens were tested by the constant rate slow
deformation method in soil suspensions taken on gas pipelines that had failed due to SCC. A change
of the main parameters which characterise steel resistance to cracking was observed. This change
included a decrease in the plastic properties of the metal, namely, a decrease in the relative elongation
and reduction of area, and the formation of surface corrosion cracks near the place of failure. The
results of the experiments show that the soils taken on gas pipelines which had failed due to SCC may
promote the formation of surface corrosion cracks.
Key Words: Stress corrosion cracking, gas pipeline, soil, constant rate slow
deformation method.
INTRODUCTION
Today, SCC is one of the serious problems in the gas industry. Last year, SCC was the
cause of some failures in gas pipelines in Western Siberia and Central and Northern Russia.
The attempts to explain SCC on gas mains only by hydrogen embrittlement or carbonate
cracking are not correct since many years of experience in the operation of offshore cathodic
protected gas pipelines and laboratory tests of the resistance of pipe steels to hydrogen
embrittlement show that the content of hydrogen absorbed by the metal under cathodic
polarization is less than the critical content which leads to embrittlement.
The Laboratory of Corrosion-Resistance Materials and Corrosion (VNIIGAS) has
conducted investigations which showed that SCC of pipe steels at potentials from 1.0-1.2 V
(SHE) in carbonate media with hydrogen numbers between 7.0 and 11.0 had not occurred.
THE TARGET OF THE INVESTIGATION
The target of the present study was to analyse the potential of soils sampled along the
routes of gas mains to give rise to pipe metal stress corrosion at corrosion potentials, i.e.,
without a cathodic protection system.
209
EXPERIMENTAL PROCEDURE
The investigations were carried out on soils taken on gas mains which had not been
subjected to failure due to SCC (soils A and B), on soils taken on failed gas pipelines having
been under operation from 6 to 18 years that failed due to SCC (C (Western Siberia), D
(Northern Russia), and E (Central Russia)), on aqueous solutions of carbonates and chlorides,
on a medium specially designed in VNIIGAS for conducting corrosion tests, and a selection
of pipe steels. The pipe steel samples were made according to NACE Standard TM 0177
(Testing of Metals for Resistance to Sulphide Stress Cracking at Ambient Temperatures).
The soil samples were dried and crushed in a mortar. A weighted sample was placed in a
flask followed by the addition of distilled water in the ratio of 1000 g water to 1000 g soil.
The suspension was placed in a cell and was given some time to settle.
The corrosion tests were conducted on round specimens 6.0 mm in diameter, using a
special test unit (MP- 5-8B type) with a travel rate of active entertainment of 1.8 x 10-6 m/sec.
The specimens were measured and marked before the test in order to determine their
relation elongation and reduction of area after the test. The specimens were degreased with
organic solvent using a common method and placed in a 250-cm3 cell. Then the cell was
filled with the test solution. The specimens were held for 72 hours followed by setting the
required deformation rate. All tests were carried out at natural aeration and ambient
temperature.
The tests on SCC resistance were conducted on not fewer than 4 specimens in each
medium. The tests ended when the specimen failed. Failed specimens were washed, dried
and measured. The test results were omitted when failure took place in the units holder, or
due to metallurgical defects or along the marks.
The SCC resistance was estimated by the relative change in the properties of the metal
tested in air and in corrosive media, and by the formation of secondary corrosion cracks on
the specimens surface.
The elongation and reduction of area were calculated on the basis of GOST 1497-84
(Metals: Methods of Tensile Tests):
= (l - l0) x 100 / l0
(1)
(2)
210
The pH values of the aqueous extracts of soils sampled on failed gas pipelines were
between 5.6 and 6.0 (C, D, and E), and the pH of soil suspensions (A and B) are
between 7.6 and 10.6. Failures of pipe steels due to SCC were not observed in soils
A and B.
The corrosion potentials of pipe steels in the soils sampled on gas pipelines which
failed due to SCC are between -0.56 and -0.58 V (SHE) (C, D, and E), the corrosion
potential in soil with a pH of 7.6 (A) was -0.48 V (SHE), and the corrosion potential
in soil with a pH of 10.6 (B) was -0.20 V (SHE).
The general corrosion rate for pipe steels in all types of soil did not exceed 0.01
mm/year.
Aqueous suspensions of soils C, D, and E contained hydrogen sulphide, acetic acid,
formic acid and compounds of lead, selenium and arsenic.
The SCC resistance tests showed that in such systems as aqueous solutions of chlorides
and carbonates and the soil suspensions A and B, the main parameters characterising steel
resistance under this test method are close to the parameters of the steel set tested in air.
Table 1. Resistance of Steel X-65 Specimens to SCC Determined by the Constant Rate
Slow Deformation Method in Media of Different Compositions
Corrosion
Potential, V
(SHE)
(%)
(%)
20.4
65.0
No
Solution Developed by
VNIIGAS
5.1
- 0.43
10.8
25.8
Yes
3% NaCl
6.8
-0.44
23.6
59.9
No
NaHCO3 - NaCO3
9.6
-0.06
21.7
66.9
No
Soil of Pipeline A
7.6
-0.44
18.8
57.6
No
Soil of Pipeline B
10.4
-0.20
23.0
60.0
No
5.8
-0.52
15.3
42.2
Yes
5.8
-0.56
17.2
45.6
Yes
Medium
Air (Control)
pH
Presence of
Corrosion Cracks
211
5.6
-0.56
21.3
56.1
Yes
When pipe steel specimens were tested in the soil suspensions sampled on the pipelines
which failed due to SCC, there was a change in the main parameters characterising steel
resistance to cracking, namely, a decrease in the metal ductility (decrease in elongation and
reduction of area) and the formation of surface corrosion cracks near the point of failure.
Table 2. Resistance of Steel X-70 Specimens to SCC Determined by the Constant Rate Slow
Deformation Method in Media of Different Compositions
Corrosion
Potential, V
(SHE)
(%)
(%)
25.2
46.1
No
Solution Developed by
VNIIGAS
5.1
- 0.43
7.4
11.0
Yes
3% NaCl
6.8
-0.44
21.0
43.1
No
5.8
-0.52
14.3
21.2
Yes
Medium
Air (Control)
pH
Presence of
Corrosion Cracks
Table 3. Resistance of Steel X-56 Specimens to SCC Determined by the Constant Rate Slow
Deformation Method in Media of Different Compositions
Corrosion
Potential, V
(SHE)
(%)
(%)
28.1
59.4
No
Solution Developed by
VNIIGAS
5.1
- 0.43
21.0
38.1
Yes
3% NaCl
6.8
-0.44
21.2
50.1
No
5.8
-0.52
14.2
48.3
Yes
5.8
-0.56
16.1
38.1
Yes
Medium
Air (Control)
212
pH
Presence of
Corrosion Cracks
Table 4. Resistance of Iron (99.9%) Specimens to SCC Determined by the Constant Rate
Slow Deformation Method in Media of Different Compositions
Corrosion
Potential, V
(SHE)
(%)
(%)
24.2
77.5
No
Solution Developed by
VNIIGAS
5.1
- 0.43
19.3
53.5
Yes
3% NaCl
6.8
-0.44
23.9
72.8
No
5.8
-0.52
23.2
75.0
Yes
Medium
Air (Control)
pH
Presence of
Corrosion Cracks
CONCLUSIONS
The laboratory test results show that the soils sampled on gas pipelines which failed due
to SCC favour the formation of surface corrosion cracks, i.e., the main cause of SCC was the
physical-chemical interaction between the metal and the components of the soils (hydrogen
sulphide, acetic acid, formic acid and compounds of lead, selenium and arsenic).
213
ABSTRACT
Recently, the failed downhole tubing from one of the oil wells in a Kuwaiti oil field was
examined at the Materials Application Department of the Kuwait Institute for Scientific Research.
This paper presents the results of a failure investigation carried out on the J55 steel tubing materials
used in many downhole oil wells in that particular oil field area. The results showed that the failure
of the tube was due to localized attack in the form of pitting and crevice corrosion that initiated on the
internal surface of the tubes. In contrast, no downhole tubing failures were reported for any of the
other oil wells located in the same field and exposed to the same aquifer environment and operation
conditions. The internal side of the failed tube plate was exposed to the oil/water stream with a 73%
water cut and high salinity content in addition to CO2 and H2S corrosive gases. The preliminary
results of the investigation indicate that the likely causes of this type of tubing corrosion failure may
be related to corrosive environmental effects combined with metallurgical or mechanical properties of
the steel tubing material. Moreover, the combined effects of both chloride and CO2 and H2S species
under certain condition are widely known to cause accelerated, premature corrosion failure in oil well
tubing. In this study, a material failure case in the oil field will be discussed. Several attempts were
made to determine the exact cause of the failure found in this oil well. However, no convincing
evidence as to the specific cause of the failure was found, due to the additional detrimental effects of
many other factors.
Key Words: Oil field corrosion, oil well tubings, downhole equipment corrosion, CO2
corrosion, H2S corrosion.
INTRODUCTION
Recently, two steel joints in a section of downhole tubing failed due to severe
perforations. Visual inspection revealed that the downhole tubing experienced severe
corrosion damage and complete perforations of the tubes walls. To elucidate the causes of
the tubing failure, the company requested the Kuwait Institute for Scientific Research (KISR)
to carry out specific tensile, hardness, and scanning electron microscopy (SEM)
examinations. The problem was first thought to be an isolated example of a manufacturing
defect; however, the present study indicates that the cause of failure merits further
investigation.
Information gathered on the oil well and failed parts indicates that only one well, No. W41, experienced accelerated corrosion failure. It was indicated that the downhole tubing was
exposed to the oil/water stream for 0 days prior to failure. Two perforated tube joints were
215
supplied by the company for an investigation into the causes of the perforations. The first
tube sample, designated as Joint No. 33, had one perforated hole (Fig. 1a). The second tube
sample, designated as Joint No. 60, had four perforated holes (Fig. 1b). An additional
nonperforated tube was also examined to compare its quality with that of the failed tubes.
Each tube measured 35 cm in length, 60.75 mm in outside diameter and 4.49 mm in wall
thickness.(Appendix A contains full details of the operations condition and production data).
This report presents the results of the investigation as well as a discussion of the likely
causes of failure and a possible solution to the problem.
LABORATORY EXAMINATIONS
Chemical Analysis and Metallographic Examinations of the Material
The material of the tube was chemically analyzed to confirm its composition and to
ensure that it complied with the requirements of the API J55 specifications. The analysis was
carried out on a cleaned section cut from the tubes.
A metallographic examination was carried out to identify the microstructures of the asreceived, perforated tubing samples. The examination was conducted on metallographically
prepared specimens cut from one of the failed tube joints. The metallographic preparation
included grinding the specimens with silicon carbide papers of the grade sequence: 320, 600,
1000 and 1200 grit. This was followed by polishing with 3 and 6 m diamond abrasive
pastes, and rinsing with distilled water and acetone. Finally, the specimens were etched in
2% nital etchant solution to reveal the microstructure and the second phase precipitates or
inclusions.
Microscopic Examinations of Perforations and Energy Dispersive Spectroscopic (EDS)
Analysis
Optical microscopy and SEM were used to observe the perforations and the dark
hydrocarbon deposits, or scale, found along the internal surfaces of the tubes. The failed
tubes were initially sectioned into two halves in a longitudinal direction away from the
defective areas before the microscopic examinations. The examinations were conducted
before and after the removal of the deposits as well as on the etched surfaces. The purpose
of etching was to identify the microstructure at the initiation sites of the perforations.
Qualitative EDS analysis was carried out to determine the composition of the deposits
both inside and outside the perforations. X-ray diffraction (XRD) analysis was carried out to
determine the composition of the deposits scrubbed from the internal surfaces of the
perforated tubes.
Mechanical Properties of the Tubing Materials
Mechanical tensile and hardness tests were conducted to investigate the quality of the
failed as-received tubing material sample. These tests were carried out to confirm the
tubings mechanical properties as well as to ensure that they complied with the requirements
of the API J55 specifications for downhole tubing material.
216
(a)
(b)
(c)
Figure 1. Perforation resulting from localized corrosion attack of internal tubing surface:
217
(a) Joint No. 33; (b) Joint No. 60; and (c) condition of interior of tubing surface
RESULTS
Chemical Composition and Microstructure of the Material
Table 1 presents the results of the chemical analysis of the material of the perforated
tubes and the as-received un-used tubes. The alloy of both tube samples was carbon steel
with minor elemental constituents of Cu, Si and Cr. The carbon and sulfur contents of the
alloy were not properly determined due to analytical limitations.
Table 1. Chemical Composition of the As-Received and Perforated Tubes
Element
C
Si
S
P
Cu
Mn
Cr
Fe
AsReceived
Tube
(wt%
0.45-0.6
0.3
0.015
0.03
0.32
1.45
0.06
Balance
Perforated
Tube
(wt%
Error
0.45-0.6
0.33
0.05
0.03
0.33
1.56
0.06
Balance
0.05
0.05
0.005
0.005
0.005
0.005
0.01
0.01
Structurally, as indicated by the equilibrium diagram of iron and iron carbide, the alloy
for both tubes was composed of ferrite and pearlite. The structure of the iron-carbon alloy is
shown in the photomicrographs of Fig. 2a and b. It can be seen that the microstructure is
typical of carbon steel material in terms of the presence of equal proportions of ferrite and
pearlite phases.
Microscopic Examinations of Perforations and EDS Analysis
of Deposits in the Failed Tubes
Visual and optical microscopic examinations of the failed tubes revealed several
perforations that appeared to originate from inside the tubes. Examinations of the internal
surfaces, after splitting the tubes into halves, showed numerous crevices and pit-like shapes in
a somewhat straight line along the longitudinal axis. The internal surfaces also exhibited
many rounded, mutually intersecting pits lying partially beneath a mixture of dark scale of
hydrocarbon deposits with iron oxide and dry oil residue. The scales were observed inside
and around penetrated areas. Cleaning the metals surface revealed the presence of crevice
corrosion in addition to the observed pits. The crevice attack appeared the same beneath all
kinds of deposits, with an approximate depth of 1.21 mm. Some of these crevices or pit-like
shapes penetrated the full thickness of the tubing (Fig. 1c). Visual examinations of the asreceived tubing indicated the presence of mill scale that covered the internal surface of the
tube.
218
EDS analysis of the deposits inside the pit-like shapes showed that they were enriched
mostly with sulfur, chloride, calcium and iron and, to a much lesser extent, with manganese
and silicon (Fig. 2c). Sulfides were present in the deposits and corrosion products.
Aggressive sulfur-and chloride-containing species were also concentrated beneath the iron
oxide layer (Fig. 2d).
XRD analysis of the scrubbed scale obtained after cleaning the internal surfaces of the
perforated tubes indicated the presence of magnetite (Fe3O4), iron oxide hydroxide
[FeO(OH)], iron carbonate (FeCO3) and iron. This suggests that the layers of deposit present
on the internal surfaces of the tube are possibly from mill scale (as Fe3O4) and also from
corrosion by-products of carbonic acid combined with iron in the form of FeCO3.
Mechanical Properties of the Tubing Material
Table 2 presents the mechanical properties of the tubing material in terms of tensile
strength, yield strength, and hardness. The results of the mechanical testing showed that the
tubing materials fall within the same range of API J55 specifications.
Table 2. Mechanical Properties of the Tubing Material
Tubing
Material
As-received
Tube
Perforated
Tube
Tensile
Stress*
(MPa)
675
675
Tensile
**
Stress
(MPa)
695
Yield
**
Stress
(MPa)
480
Rockwell
Hardness
(HRB)
94
94
DISCUSSION
Both the optical microscopy and the SEM examinations indicate that the failure of the
tube was caused by a typical case of localized corrosion caused by differential acid
concentration cell. The fact that localized attack occurred on the internal surfaces of the
tubing at accelerated rates during 10 days of exposure indicates that the cause of this
corrosion phenomenon is related to the aggressive nature of the environment. Under normal
conditions in deaerated oil field environments of CO2 and H2S, one would not expect
corrosion perforation to occur at such a fast rate.
Generally, the corrosion rates of steel are not as high in sour water systems (i.e., those
usually observed in oil field systems with a high water cut) as they are in CO2 systems due to
the somewhat protective nature of sulfide scale (FeS mackinawite) relative to iron carbonate
(FeCO3) unless oxygen contamination has occurred [1].
Typically, deaerated systems with less than 0.02 bar CO2 partial pressure are not
considered excessively corrosive to steel, but they can exhibit corrosion rates of up to 0.20
mm/year (10 mpy). As the partial pressure increases, the corrosion rate increases. At 0.5 bar
CO2 partial pressure, the corrosion rate of steel (i.e., 1 mm/year (40 mpy)) is high enough to
require inhibition if the bicarbonate is low as in condensed water systems. At 2.0 bar CO2
partial pressure, the system would be at a pH in the range of 3.5-4.5, and can be considered
220
severe from the standpoint of weight loss corrosion (i.e., a corrosion rate of > 2.5 mm/year
(100 mpy)).
The combination of hydrogen sulfide and carbon dioxide is more aggressive than
hydrogen sulfide alone and is frequently found in oil field environments. Once again, the
presence of even minute quantities of oxygen can be disastrous. In all cases, increased
velocity would be expected to increase the corrosion rate of steel [2].
The following ferrous corrosion products would form with H2S and CO2 in the presence
of oxygen and low solid water. For corrosion, they are the only products of concern:
Fe + H2S FeS + H2
(Sour corrosion)
(1)
(2)
(3)
The iron sulfide produced by reaction (Eq. 1) generally adheres to the steel surfaces as a
black powder or scale. The scale tends to cause local acceleration of corrosion because the
iron sulfide is cathodic to the steel; this usually results in deep pitting during O2 reduction
reactions along this FeS layer. Oxygen will provide a high electrochemical potential because
it is a strong, rapid oxidizing agent. This means that it will easily combine with electrons at
the cathode, and allow the corrosion to proceed at a rate limited primarily by the rate at which
oxygen can diffuse to the cathode. The primary concern in this case would be when the H2S
partial pressure is 0.05 psi.
As a first approximation, calculations of the partial pressure of both carbon dioxide and
hydrogen sulfide are useful for the present case study in predicting the degree of corrosivity
of the oil well (i.e., No. W-41):
Partial pressure of CO2 = 1500 x 0.07 = 105 psi
Partial pressure of H2S = 1500 x 0.001 = 1.65 psi
Using the CO2 partial pressure as a yardstick to predict corrosion, it was found that the
CO2 partial pressure was above 30 psi, which usually indicates the onset of corrosion,
however, in this study, the volume fraction of CO2 over that of H2S was < 200. This
indicates that the presence of small concentrations of H2S play a prominent role in the
corrosion mechanism involved in the reactions (Eqs. 1-3). If the given volume fraction is >
200, then carbon dioxide will be the controlling factor for the reactions; this does not apply to
the present case and its oil field environment.
According to a computer modeling program [3] used in this study to estimate the
corrosion rate on the pitted tubing, and based on the analysis of the production data in
addition to the operation conditions given in Appendix A, the following two cases were
predicted:
221
1. The production of oil and formation water with H2S and CO2 under deaerated
conditions (i.e., oxygen is excluded) would result in a corrosion rate resulting
in tubing perforation after more than two years of exposure, and
2. Changing the production conditions to include oxygen in addition to H2S and
CO2 would result in a worst-case corrosion rate leading to tubing failure in
about eight days (10 days in service to actual failure).
Based on the examination and this preliminary computer analysis from CLI
International, Inc., it was assumed that case 2 is likely to model the situation involved in the
tubing failure. However, according to on-site field inspection of the oil well and observation
of the huge amount of gas pressure released from the wellhead, when the pressure valve was
opened, the theoretical assumption based on the combined effects of oxygen and corrosive
gases could not be accurate because oxygen had no chance to diffuse into the well tubing
under such a high-pressure release of gas at the outlet. Moreover, there was no chance for
oxygen to be drawn into the well through leaky valves or the expansion of joints in this
solidly designed oil well tubing part. Therefore, the only solution was to look for other
causes of damage that would have enhanced the corrosivity of the gases (i.e., CO2 and H2S)
and could have contributed to the acceleration of the rate of corrosion attack.
On observing the case history of the oil well (see Appendixes A and B) and by
comparing the performance of this oil well with respect to the nearest oil wells located within
one kilometer in the same oil field, the following suspected factors can be assumed: The
failure of the tubing was initiated due to differential acid concentration cell (case 1) that had
been established beneath crevices that were hydrocarbon in nature, and being strengthened
with a very high propagation rate of corrosion attack caused by one or more of the following
suspected factors:
Appendix B,
Electrical power problems (i.e., a rectifier power supply problem),
Galvanic coupling effects between the materials of the ESP and the internal
surface of the tube,
Failure including doglegs, splits, and leakage of the well casing materials at a
certain depth adjacent to the well tubing promoted after the burning of the well
during the Iraqi invasion, and
Faulty electrical ground connection (ground electrical contact was made to the
well tubings), and
Stray current effect from either the ESP or other exterior effects.
CONCLUSIONS
1. Metallographic examination, SEM and mechanical testing of the tubing did not show
any major differences between the as-received and the failed tubing in terms of
mechanical properties or the presence of second phase particles and inclusions. The
minor additions of Cu, Cr and Si did not contribute much to the poor corrosion
properties of the steel tubing; however, the presence of higher contents of
nonhomogenous MnS in both tubing specimens may also indicate the possibility of
222
APPENDIX A
Case History for Well No. W-41
Industry: A Kuwaiti oil production
Specimen location: Downhole tube from Well No. W-41
Specimen orientation: Vertical
Years/days in service: 10 days
Salinity: 80,000 to 90,000 ppm
Average water cut: 73%-Temperature: 116oF (47oC). Total pressure: 1250-1500 downhole
CO2 Concentration: 7 vol% H2S Concentration: 0.11 vol%
Failed samples given: Two failed tubing samples with tube specifications J55-2 3/8 in. O.D.
Sample designation: Sample No. 3 from Joint No. 33. Downhole tubing depth: 1008 ft
Failure condition: One perforated hole
Sample designation: Sample No. 4 from Joint No. 60. Downhole tubing depth: 1832 ft
Condition: 4 perforated holes
Engineering component connection: Electrical submersible pump (ESP) at 2,258 ft
Oil well fluid level: static 527 ft. Dynamic 558 ft
223
APPENDIX B
.History of the Premature Failure of Downhole Equipment and Tubings in Well No. W-41.
Visual Inspection Findings of Pulled Equipment
Failure Failure Run Life
No.
Date (months)
1
Jan.
2.5
90
2
May
3.5
90
3
Oct.
5
92
___
burnt
leaking
___
___
shorted
leaking
damaged
corroded
burnt
___
___
___
___
pump
Joint.
#29
burnt
with
2 holes
burnt
Ext. corr.
erosion
corrosion.
___
good
___
good
#30
#59
External
corrosion
Erosion
corrosion
___
Ext.
Corr.
left
in
hole
Jul.
93
Jan.
94
___
good
Nov.
94
10
good
(red alloy)
Nov.
94
0.5
good
(red alloy)
Jan.
95
1.5
10
Feb.
95
10 days
11
Mar.
95
40 days
good
(carbon
steel)
good
(carbon
steel)
good
(carbon
steel)
12
Jul.
95
42 days
13
Sept.
95
29
(1)
one
hole
one
hole
Iraqi
Invasion
DDI
while
RIH
Separator
good
___
Protector
___
Motor
Jan.
90
good
(carbon
steel)
good
(carbon
steel)
30
(1)
good
hole &
good
Ext. Corr.
(Red Alloy)
(carbon
steel)
reused
shorted
good
+big hole
stuck
(Red Alloy)
(carbon
(carbon
steel)
steel)
good
good
good
(carbon
(carbon
(Red Alloy)
steel)
steel)
good
good
good
(carbon
(Carbon
(red alloy)
steel)
steel)
wire
bolts<------corroded---connection
--------->red alloy
loose
(carbon
steel)
good
good
1/16 inch hole
(carbon
(red
(red alloy)
steel)
alloy)
good
red
red alloy
(carbon
alloy
steel)
33
37
39
(1)
(1)
(1)
Cable
Remarks
Pump
PSI
Failed Tubing
Joint
Joint No. of
No.
Holes
___
___
not
R.C.
work damage
___
___
shorted
(red alloy)
DDI
while
RIH
pump
Joint
___
F.C.
burned
&
parted
good
___
good
___
good
___
___
___
one
hole
hi Volt
hi Amp
#37,
#39,
#50
___
#50,
#58,
#59
58
(1)
59
(3)
5 holes
3 holes
7 holes
red
alloy
50
(2)
60
(1)
N-80
grade
tubing
N-80
grade
tubing
63 pup
(1) joint
(2)
224
DDI
while
RIH
At Surface
85C
110 psi
15 Vol.%
1.1 Vol.%
ABSTRACT
Lower quality opportunity crudes are now processed in most refineries, and the source of the
crudes may vary daily. These feedstocks, if not properly handled, can result in reduction in service
life of equipment as well as costly failure and downtime. Analytical tools are needed to predict their
high-temperature corrosivity toward distillation units. Threshold levels of total sulfur and total acid
number (TAN) have been used for many years as rules of thumb for predicting crude corrosivity.
However, it is now realized that they are not accurate in their predictive ability. Crudes with similar
compositions and comparable with respect to process considerations have been found to be entirely
different in their impact on corrosion. Naphthenic acid content, sulfur content, velocity, temperature,
and materials of construction are the main factors affecting the corrosion process. Despite progress
made in elucidating the role of the different parameters on the crude corrosivity process, the main
problem is in calculating their combined effect, especially when the corroding stream is such a
complex mixture. The TAN is usually related directly to naphthenic acid content. However,
discrepancies between analytical methods and interference of numerous components of the crude itself
lead to unreliable reported content of naphthenic acid. The sulfur compounds, with respect to
corrosivity, appear to be related more to their decomposition at elevated temperature to form hydrogen
sulfide than to their total content in the crude. This paper reviews the present situation regarding
crude corrosivity in distillation units, with the aim of indicating the extent of available information,
and areas where further research is necessary.
Key Words: Naphthenic acid corrosion, crude oil corrosion, high temperature corrosion
INTRODUCTION
The quality of crude oils processed around the world is worsening. The higher densities
of crudes and higher contents of sulfur, acids and other impurities found in crude oils have
increased the likelihood of corrosion failures in the processing plants. Moreover, it is now
realized that many of the old rules of thumb, namely threshold levels of sulfur and total acid
number (TAN) or neutralization number, do not appear to be accurate in their predictive
ability. Analytical tools are needed to predict their high-temperature corrosivity toward
distillation units. Sulfur at a level of 0.2% and above is known to be corrosive to carbon and
low alloy steels at temperatures from 230C (450F) to 455C (850F). When sulfur is the
only contaminant, McConomy curves [1], with the help of correction factors, are used to
predict the relative corrosivity of crude oils and their various fractions as well as the effect of
225
operational changes on corrosion rates already experienced in the field. However, when
naphthenic acids are present, crude corrosivity prediction becomes more complex. Crudes
with similar compositions and comparable with respect to process considerations have been
found to be entirely different in their impact on corrosion.
MANIFESTATION OF NAPHTHENIC ACID CORROSION
Naphthenic acids are organic acids present in many crude oils from around the world,
especially those from California, Venezuela, the North Sea, Western Africa, India, China, and
Russia. They have the following generic chemical formula: R(CH2)nCOOH, where R is a
cyclopentane ring and n is typically greater than 12. Naphthenic acid corrosion is
differentiated from sulfidic corrosion by the nature of the corrosion (i.e., pitting and
impingement) and by its severe attack at high velocities in crude distillation units. Crude
feedstock heaters, furnaces, transfer lines, feed and reflux sections of columns, atmospheric
and vacuum columns, heat exchangers, and condensers are among the type of equipment
subject to this type of corrosion [2]. Damage is in the form of unexpected high corrosion
rates on alloys that would normally be expected to resist sulfidic corrosion. Isolated, deep
pits in partially filmed areas and/or impingement attack in essentially film-free areas is typical
of naphthenic acid corrosion [3,4]. In many cases, even very highly alloyed materials (i.e., 12
Cr, AISI 316 and 317, and in some severe cases even 6% Mo stainless alloys) have been
found to exhibit sensitivity to corrosion under these conditions.
PARAMETERS AFFECTING NAPHTHENIC ACID CORROSION
TAN (or neutralization number), sulfur content, velocity, degree of vaporization,
temperatures, and alloy composition (i.e., Cr and Mo) were found to be the main factors
affecting the corrosion process.
Total Acid Number
The TAN was related in early studies to the naphthenic acid corrosion rate, and its
threshold was believed to be around 0.5 mg KOH/g [3]. Analysis of crudes TAN
distribution as a function of the true boiling point showed where the acids concentrated in the
refinery and resulted in better correlation of TAN with corrosion experienced in the field [5].
However, correlating the TAN of specific cut to their corrosivity was still far from being
reached. Even naphthenic acid weight percent did not correlate to experienced corrosion [6].
A standard laboratory test was developed and showed promising crude corrosivity prediction.
An index called the naphthenic acid corrosion index (NACI) was calculated from the
exposure of a carbon steel coupon at 500F (260oC) for 48 hours in the fraction to be tested
[7]. The index was the ratio of the corrosion rate of the coupon in mills per year (mpy) to the
weight of its corrosion film in milligrams per square centimeter. It was postulated that a
calculated ratio under 10 indicated sulfidic corrosion while a higher index indicated
naphthenic acid attack. However, this index was developed from static test results, and
correlations to high velocity might not be that simple and need to be verified. Moreover,
carbon steel was the material used in these tests while most of the refineries process
naphthenic crudes with a minimum alloy of 5 Cr.
Sulfur Content
226
Most crude oil feedstocks vary greatly in both the amount of sulfur and the type of
sulfide species present. It is believed that the sulfur content does not reflect the true effect of
sulfur. A more important factor may be the capability of these sulfur compounds to form H2S
during heating in the refining process [8]. At low temperatures, certain sulfur compounds in
the crude may reduce the severity of naphthenic acid corrosion [9]. In this case, the sulfide
film may offer some degree of protection from the acidic corrosion. At higher temperature
conditions, the presence of naphthenic acids was found to increase the severity of sulfidic
corrosion. Presumably, the presence of these organic acids disrupted the sulfide film, thereby
promoting sulfidic corrosion on alloys that would normally be expected to resist this form of
attack (i.e., 12 Cr and higher alloys). Figures 1 and 2 show the effect of chromium and
molybdenum content as well as TAN and sulfur on the corrosion rate of crude fractions tested
in the laboratory at a velocity of about 3 m/s (10 ft/s) and temperature of 370C (700F) for
three days. In the vacuum heater feeder line (VHFL) cut the 1.5 Cr and 5 Cr showed the
same corrosion rate, but in the long resid (LR) fraction the 5 Cr and 9 Cr behaved similarly.
In general, the corrosion rate decreased steadily with increase in Cr and Mo. However, both
TAN and sulfur content do not correlate in any way to corrosion rate. In the VHFL, the
fraction with medium TAN and sulfur was the most corrosive to low alloy steels. In the LR,
the fraction with the lowest TAN and sulfur was the most corrosive. In this case, blending a
high TAN crude to lower the acid content did not provide the expected results and aggravated
corrosion. These cases are common and refinery experience shows that prediction of
corrosion is more complex than it is believed to be.
Temperature
Naphthenic acid corrosion occurs primarily in high velocity areas of crude distillation
units in the 220 to 400C (430 to 750F) temperature range. No corrosion damage is found at
temperatures above 400C (750F) probably, because of the formation of coke at the metal
surface. The corrosion rate of all alloys of importance to the distillation units increases with
increases in temperature.
Velocity
The flow regime and the degree of vaporization have a significant effect on both sulfidic
corrosion and naphthenic acid corrosion. The higher the acid content generally, the greater
the sensitivity to velocity. In fact, in some cases, it appears possible to obtain very high
corrosion rates even at very low levels of naphthenic acid content (i.e., TAN 0.3) and low
sulfur content when combined with high-temperature and high velocity.
Materials of Construction
The normal materials of construction used in crude distillation units are carbon steel , 5
Cr, 9 Cr, 410SS, and 316SS [10]. If only sulfur is present and the temperature is above
288C (550F), 5 Cr or 12 Cr cladding is recommended for crudes over 1% sulfur when no
operating experience is available [2]. If hydrogen sulfide is evolved, 9 Cr minimum is
preferred. In contrast to high-temperature sulfidic corrosion, low-alloy steels containing up to
12% Cr provide no benefits over carbon steel in naphthenic acid service [1]. With 316 SS
(with 2.5% Mo minimum) or better, with 317 SS with a higher Mo content (3.5% minimum),
cladding of the vacuum column is recommended when TAN is above 0.5 mg KOH/g and in
an atmospheric column when the TAN is above 2.0 mg KOH/g [2].
227
120
40
0
0
10
15
20
25
Cr + Mo (%)
50
30
20
10
0
0
10
15
20
25
Cr + Mo (%)
adequate and economic protection if it is closely monitored and used for specific fractions
that are known to be particularly severe, or if it fluctuates with feedstock quality. When
possible, upgrading the construction materials to a higher chrome and/or molybdenum alloy is
the best solution for long term reliability.
CRUDE CHEMISTRY AND CORROSIVITY CORRELATION
Most of the laboratory studies and refinery experience so far have shown that crude
corrosivity prediction is very complex and that further studies are needed to correlate the
chemistry of crudes to refinery corrosion. Unfortunately, crude chemistry (sulfur and TAN),
process variables (temperature and velocity), and failure analysis (sulfidic and/or naphthenic
acid corrosion) are far from being assessed uniformly throughout the industry. To be able to
achieve correlations among refineries and between laboratories and plants, the measurement
method for each parameter needs to be defined precisely.
Naphthenic Acid Distribution
Naphthenic acid content is generally expressed in terms of TAN. ASTM D974 is a
colorimetric method., with reproducibility of 15% and interference from inorganic acids,
esters, phenolic compounds, sulfur compounds, lactones, resins, salts, and additives such as
inhibitors and detergents. ASTM D664 is a potentiometric method with reproducibility of 20
to 44% depending on the end point (i.e., buffer or inflection), type of oil (i.e., used or fresh),
and titration mode (i.e., automatic or manual), and the same interfering impurities as ASTM
D974. Both ASTM methods do not differentiate between naphthenic acids, phenols, carbon
dioxide, hydrogen sulfide, mercaptans, and other acidic compounds present in the oil. In
addition, the two methods were compared [5], and D664 yielded numbers that were 30 to
80% higher than D974. Thus, prediction of crude corrosivity based on TAN alone could be
misleading. Additionally, for assessment of plant corrosion effects, the naphthenic acid
content needs to be determined for each cut in order to predict exactly where the acids will
concentrate during the distillation of the crude. The isolation and analysis of naphthenic
acids from crude oil may be performed adequately with methods such as UOP 565
(potentiometric) and UOP 587 (colorimetric), chromatographic separations, or other available
analytical techniques [12,13]. The relative abundance of naphthenic acid and its average
molecular weight (i.e., boiling point) may be determined. In addition, the assays of crude
must be current [2]. Once steam flooding or other recovery method is begun in an oil field,
the specific gravity and the organic and sulfur content of the crude can change. Fire flooding,
when used in some fields, tends also to increase the naphthenic acid content.
Hydrogen Sulfide Evolution with Temperature
Sulfur is the most abundant element in petroleum other than carbon and hydrogen. It
may be present as elemental sulfur, hydrogen sulfide, mercaptans, sulfides, or polysulfides.
The total sulfur content is generally analyzed with the ASTM D4294 method using x-ray
fluorescence. Halides and heavy metals interfere with this method. The capability of these
sulfur compounds to form H2S during heating in the refining process, rather than their total
content, is believed to correlate to corrosion in the plants [8]. However, a standard procedure
for determining hydrogen sulfide evolution with temperature is not currently available.
229
of the laboratory apparatus. Figure 3 shows a schematic diagram of a rotating autoclave with
a condenser for the return of light components, and Fig. 4 is a schematic diagram of a jetimpingement laboratory setup. Both of these apparatus are used in the laboratory to simulate
corrosion in the field at high velocities. Table 1 compares the shear stress level between the
field and the laboratory. The results show that the wall shear stress changes drastically with
the degree of vaporization, and that identical fluid flow in the laboratory and the field do not
correspond to the same level of shear stress.
Table 1. Wall Shear Stress (in Pascals) Calculated at Different Velocities
(VGO cut of 0.7 Specific Gravity and 0.55 Centistokes Viscosity
at 700oF)
Velocity
3 m/s
(10 ft/s)
Rotoclave
Jet Impingement
18
4
DV = 0%
46
DV = 30%
32
DV = 70%
14
DV = Degree of vaporization
6 m/s
16 m/s
(20 ft/s)
(50 ft/s)
Laboratory Setup
58
N/A
13
80
Plant
158
691
111
514
47
286
33 m/s
(100 ft/s)
66 m/s
(200 ft/s)
N/A
298
N/A
1049
2830
2080
862
10291
5148
2210
three days of exposure. Differences in flow velocity on the general corrosion of the three
alloys was minimal. However, a significant increase in the pitting corrosion rate with
increases in flow from 10 ft/s to 200 ft/s was found especially for the 5 Cr and 9 Cr alloys.
Corrosion rates in the field are evaluated by on-line monitoring tools which indicate only
general corrosion rates unless the equipment is inspected for pitting and/or impingement.
CONCLUSIONS
It has clearly been proven through extensive laboratory and plant studies that predicting
crude corrosivity by using the general rules of total acid and sulfur content is not reliable
especially with the wide range of crude oil feedstocks being processed today. Naphthenic
acid content and distribution in side cuts, hydrogen sulfide evolution with temperature, wall
shear stress, temperature at the metal surface, and materials of construction are the main
factors affecting the crude corrosivity process. The exact mechanisms which are operating
are not precisely known at this point, and much research and testing is necessary to build a
more comprehensive understanding. Based on the complexity of the situation and the current
level of understanding, each case must be dealt with on an individual basis until a more
comprehensive methodology for assessment can be developed. It is possible, however, to
provide a practical assessment of the plant corrosion process by establishing a more
comprehensive database from both laboratory and field experience where the various
parameters affecting naphthenic acid corrosion can be more extensively and unambiguously
defined and quantified. This information will serve as a firm basis for materials selection
decisions, feedstock blending requirements and plant operating conditions.
REFERENCES
1. L. Garverick, Ed., Corrosion in the Petrochemical Industry, ASM International, 1994.
2. R.A. White and E.F. Ehmke, Materials Selection for Refineries and Associated Facilities,
NACE, Houston, Texas, 1991.
3. W.A. Derungs, Corrosion 12, 12, 1956, p. 617t.
4. J. Gutzeit, Materials Performance 16, 10, 1977, p. 24.
5. R.L. Piehl, Materials Performance, January 1988, and Paper No. 196, Corrosion/87,
NACE.
6. E. Babian-Kibala, et al., Naphthenic acid corrosion in a refinery setting, NACE
Conference, Corrosion/93, Paper No. 631, 1993.
7. H.L. Craig, Naphthenic Acid corrosion in the refinery, Paper No. 333, Corrosion/95,
NACE.
8. R.L. Piehl., Corrosion, June 1960, p. 305t.
9. Heller, Materials Protection, September 1963.
10. F. Blanco and B. Hopkinson, Experience with naphthenic acid corrosion in refinery
distillation process units, NACE Conference, Corrosion/83, Paper No. 99, 1983.
11. G.L. Scattergood and R.C. Strong, Naphthenic acid corrosion: An update of control
methods, NACE Conference, Corrosion/87, Paper No. 197, 1987.
12. Tseng-Pu Fau, Energy and Fuels 5, 3, 1991, p. 371.
13. I. Dzidic, et al., Analytical Chemistry 60, 13, July 1, 1988, p. 1318.
14. K.D. Effird, et al., Experimental correlation of steel corrosion in pipe flow jet
impingement and rotating cylinder laboratory tests, Corrosion/93, Paper No. 81, NACE.
232
VDM Technologies
11210 Steeplecrest, # 120, Houston, Texas 77065, USA
2
Krupp-VDM GmbH
P.O. Box 1820, 58778 Werdohl, Germany
ABSTRACT
The materials of construction for the modern chemical process and petrochemical industries not only
have to resist uniform corrosion caused by various corrodents, but must have sufficient localized corrosion
and stress corrosion cracking resistance as well. These industries have to cope with both the technical and
commercial challenges of rigid environmental regulations, the need to increase production efficiency by
utilizing higher temperatures and pressures, using more corrosive catalysts, and at the same time possess
the necessary versatility to handle varied feed stock and upset conditions. Over the past 30 years
improvements in alloy metallurgy and a fundamental understanding of the role of various alloying
elements has led to newly developed Ni-Cr-Mo and Ni-Mo alloys, which not only extend the range of
usefulness of existing alloys by overcoming their limitations, but are also cost-effective and open new
avenues of applications. This paper presents the various metallurgical, thermal stability and corrosion
resistance characteristics of some newer alloys along with actual case histories, where these alloys have
solved specific problems.
Key Words:
INTRODUCTION
At one time one, of the major factors in any material selection was initial cost with little
thought given to maintenance and the cost associated with lost production due to unscheduled
equipment downtime. In today's economic environment, increased maintenance costs and
downtime have placed a greater emphasis on the need for reliable, safe and versatile performance
of process equipment.
Prior to the 1950's, the alloy choices to combat corrosion were very limited. The latter half
of the 20th century saw a phenomenal growth in the development of new nickel-based alloys due
to improved melting and thermo-mechanical processing innovations, a better fundamental
understanding of the role of various alloying elements and their effect on both corrosion and
physical metallurgy behavior. Even though the standard austenitic stainless steels (Alloy 304L
and 316L) have been and continue to be the workhorse of many industries, their vulnerability to
localized corrosion and chloride stress corrosion cracking (SCC) has been a major problem in
233
many chemical processes. The knowledge that chromium and molybdenum improved the
localized corrosion resistance and increased nickel enhanced the chloride SCC resistance led to
different alloys with varying nickel, chromium, molybdenum and iron contents. The knowledge
that in certain low nickel containing alloys nitrogen could be added to impart certain unique
mechanical, metallurgical and corrosion characteristics was used to come up with a completely
new 6% Mo alloy class which was very cost-effective and in certain cases approached or equaled
the corrosion resistance of the more expensive high nickel containing alloys. Two alloys of this
6% Mo stainless steel class, with varying chromium and nickel contents, were developed to
bridge the performance gap between the standard austenitic stainless steel and the very high
performance nickel-based alloy of the Ni-Cr-Mo family such as Alloy C-276, Alloy C-22 and the
most recent and advanced development, Alloy 59. Table 1 gives some of the alloy groupings of
the materials of construction used today, whereas Table 2 lists the effects of the various alloying
elements in the Ni-Cr-Mo-containing alloys. As one moves upward from Type 304 stainless
steel metallurgy (Group I of Table 1) to higher alloys groupings such as Groups II, IV and VI,
corrosion resistance improves, as evidenced by their chemical composition and the higher
calculated pitting resistance equivalent (PRE) shown in Table 3. This higher PRE accounts for
the improved corrosion resistance of the various alloys in a variety of environments. For
interested readers, a list of references is provided for further in depth reading to gain a better
understanding of these newer developments [1-16].
Table 1. Some Austenitic Corrosion Resistant Alloys for Combating Aqueous Corrosion
Alloy Group
I
II
III
IV
V
VI
Generic Description
Iron-based 18-8 austenitic SS alloys
High performance austenitic SS alloys
Ni-based general purpose alloys
6% Mo superaustenitic SS alloys
Ni-based special alloys
Nickel based high performance alloys
VII
Typical Alloys
304, 316, 317
904L, 20, 28, 825
200, 400, 600, 800
1925hMo, 31*, 254SMo,
B-2, B-3*, B-4*
G-3, G-30, 625, C-276,
C-4, C-22, 59*, 686*
33*
contain tungsten, except Alloy 59. Not only is the uniform corrosion behavior and the thermal
stability improved, its localized corrosion resistance as measured by the standard ASTM G48 test
method in 10% FeCl3 is also enhanced. Table 6 clearly shows the beneficial effects of higher
PRE due to the highest Cr plus Mo content in Alloy 59. Further details on Ni-Cr-Mo alloys are
provided elsewhere [1-3,10,11,14,15,16].
Applications of Alloy 59
Due to its highest PRE and these unique corrosion-resistant properties, Alloy 59 has found a
number of successful applications, where other nickel-based alloys have been either inadequate
or marginal in performance. Some of these applications are described below.
Pollution Control
Combustion gases from burning fossil fuels or from waste incineration of municipal or
hazardous waste contain acidic pollutants such as SO2, SO3, HCl and Nox, which must be
scrubbed before the gases are released into the atmosphere. The equipment most frequently
employed to achieve this is a wet scrubber. Operating conditions in critical sections of wet
scrubbing systems can be extremely severe: for example, in condensates chloride levels may
approach 100,000 ppm at pH values below 1 and temperatures of 80C. Laboratory and field
testing has shown Alloy 59 to be one of the very few metallic materials able to withstand such
aggressive corrosive conditions. In one lignite fired power station in Germany, 40 month field
test rack data showed Alloy 59 to be the only alloy free of any localized attack.
Table 2. Alloying Elements and Their Major Effects
Alloying
Element
Ni
Cr
Mo
W
N
Cu
Ti, Cb, Ta
Fe
235
PRE*
37
29
32
38
48
54
45
50
52
69
65
74
76
Alloy
Media
C-276
ASTM 28A
168
ASTM 28B
55
Green Death
26
10% HNO3
19
65% HNO3
750
10% H2SO4
23
50% H2SO4
240
1.5% HCl
27
10% HCl
239
10% H2SO + 1% HCl
87
10% H2SO4 + 1% HCl (90C)
41
* To convert to mm/y, multiply by 0.0254.
236
Alloy
59
24
4
5
2
40
8
176
15
179
70
3
Table 5. Thermal Stability Per ASTM G28B After Sensitization Treatment at 1600F
**
Sensitization (hr)
Alloy C-276
Alloy 59***
1
>1000
4
3
>1000
4
5
>1000
17
* To convert to mm/y, multiply by 0.0254
** Alloys C-276, 22 and 686 - Heavy pitting attack with grains falling due to deep intergranular
attack.
*** Alloy 59 - No pitting attack.
Table 6. Critical Pitting and Crevice Corrosion Temperature Per ASTM G-48
Alloy
PRE
24
32
29
32
45
38
52
50
54
65
69
74
76
thousand, which significantly reduced periodic cleaning costs. Many hundreds of tons of Alloy
59 have been ordered in recent years for flue gas desulphurization systems of both power stations
and incinerators throughout the world [14].
Synthesis of Acrylates and Methacrylates
One process for the synthesis of acrylic or methacrylic esters involves reacting the
corresponding acids with fatty alcohols, in the presence of para-toluene sulphonic acid as a
catalyst. The reaction temperature is 130C, and the reaction is carried out under oxidizing
conditions. Heating is by an internal steam coil. Following rapid failure of the material
previously used for the steam heating coil, a series of plant tests was made with alloys including
904L, 28, G-3, 625, C-276, 31, and 59. The only alloy, which showed no pitting or crevice
corrosion, and a corrosion rate of less than 0.01 mm/yr, was Alloy 59. A steam heating coil made
of Alloy 59 was installed in 1993 and has operated without any problems ever since.
Aluminum Refining
When aluminum scrap is remelted, the molten metal is protected from oxidation by a layer
of sodium and potassium chlorides. During the refining process this salt layer becomes
contaminated with ammonium chloride. These chloride salts then have to be purified and
recovered. This is done by dissolving them in water, and then recrystallizing the solution. In one
European plant, the solution thus obtained contains 20-25% NaCl, 6-8% KCl and 5-8% NH4Cl.
The pH is in the range 4.5 to 6. The evaporator operates at a temperature of 107C. The initial
plant was built in rubber-lined steel, and failed rapidly due to cracking of the rubber lining and
subsequent corrosion of the underlying carbon steel. A plant test in 1994 with Alloy 59 showed
that after some 3800 hours of operating time, no corrosion could be detected. The
recystallization plant has since been rebuilt in Alloy 59.
Metals Processing
In a copper plant, the SO2-rich gas from the flash furnace is scrubbed with a solution of 5%
H2SO4 at a temperature of 45-60C. The acid produced has a concentration of typically around
50-55% H2SO4 and a temperature of about 75C. The chloride and fluoride contents of this acid
are both high, at about 7000 ppm. Tests were carried out using both Alloy 59 and Alloy 31.
Corrosion rates for both alloys were below 0.013 mm/yr with no localized corrosion. Following
these tests, Alloy 31 was purchased for the scrubber internals handling the produced acid, and
Alloy 59 for the induced draft fans. These have been in successful operation for the last two
years with no detectable corrosion. Since then another order has been placed.
Citric Acid Production
Citric acid is produced in one plant by reacting calcium citrate with 95%-98.5% sulphuric
acid at 95C-97C. A pilot installation of Alloy 254SMo failed rapidly. A three month test with
Alloy 59 gave a corrosion rate of 0.05 mm/yr. The first of four reactors made of Alloy 59 was
installed in 1990, and continues to operate well with no problems.
Effluent Treatment
Effluent from an acetic acid derivatives plant is cooled in Alloy C-276 plate heat
exchangers. These require frequent replacement. Initial tests suggested that Alloy 59 might be a
better alternative, so more extensive testing was carried out. The test conditions, and the
238
corrosion rates observed during testing led to the selection of Alloy 59 to replace Alloy C-276 for
the new effluent treatment plant.
Fine Chemicals Production
At one major chemical company, the production of fluorinated organic chemicals requires a
halogen exchange reaction in which one fluorine atom is substituted for chlorine in the molecule.
This reaction is carried out at about 100C in the presence of ammonium fluoride and a
proprietary catalyst. Because of the severely corrosive conditions, extensive tests were made with
Alloy 59 and with other alloys of the Ni-Cr-Mo and Ni-Mo family. The lowest corrosion rate
was exhibited by Alloy 59. A 2600 US-gallon reactor (9.8m3) (Fig. 1) was built to ASME code
requirements and has been giving excellent performance over the past 24 months. It is expected
that a life cycle cost analysis will show Alloy 59 to be at least 50% cheaper than the next best
candidate alloy belonging to the Ni-Mo family, Alloy B-2. Due to the excellent performance of
Alloy 59, another bigger ASME vessel has now been ordered by the same chemical company
(4,000 gallons capacity).
Figure 1. ASME code vessel made of Alloy 59 producing chlorinated and fluorinated chemicals
Alloy 625 was giving only three years life in a column in a fine chemicals plant.
The operating conditions were a temperature of 140C and a medium consisting of 83.1% water,
14.3% sodium bisulphate, 0.34% sodium sulphate, 0.02% acetone, 0.46% isopropanol, 0.06%
copper sulphate, 0.04% DCNB, and 1.5% various organics. Tests were carried out both at the
inlet to the column, and at the foot of the column. Based on the results of these tests, an inquiry
was issued for a new column to be built in Alloy 59.
239
There are many other applications of Alloy 59 which continue to find increasing usage and
specification in the various industries throughout the world. This alloy is covered under
appropriate ASTM, AWS and ASME specifications.
6% Mo ALLOYS
These alloys, such as Alloy 1925hMo, were derived from alloy 904L metallurgy by
increasing the molybdenum content from 4.5% to 6.5% and fortification with 0.2% nitrogen.
This addition of nitrogen provided added benefits of improved localized corrosion resistance,
thermal stability and mechanical properties. These alloys are readily weldable with over-alloyed
filler metals, such as Alloy 625, Alloy C-276 or Alloy 59 to compensate for segregation of
molybdenum occurring in the interdentritic regions of weldments. A higher chromium-nickel
version of these alloys known as Alloy 31 further improves the corrosion resistance
characteristics in a variety of media. Its corrosion resistance in sulfuric acid in medium
concentration range is superior to even that of Alloy C-276 and Alloy 20 (Table 7). However,
one must be careful, when specifying this alloy for higher concentrations and temperatures. At
80% concentration and temperatures above 80C, Alloy 31 exhibits active behavior. The 6Mo
alloys have found extensive usage in pulp and paper, phosphoric acid, copper smelters, sulfuric
acid production, pollution control, rayon production, specialty chemicals production, marine and
offshore applications, heat exchangers using seawater and brackish water as coolant, pickling
baths and many other applications. These alloys are covered under appropriate ASTM and
ASME specifications. More details on these 6Mo alloys are presented elsewhere [4-8]. Some
applications of 6Mo alloys are presented in Tables 8 and 9.
Table 7. Corrosion Resistance in Sulfuric Acid
60C
H2SO4
Alloy Alloy Alloy
Alloy
(%)
20
C-276 31
20
<5
<1
<0.1
40
<5
<2
<0.1
60
>5
<2
<0.1
80
5
<1
0.2
To convert to mm/y multiply by 0.0254
100C
Alloy Alloy
20
10
10
11
18
20
>25
>25
>50
>50
C-276
4
3
4
15
31
<0.1
<0.2
0.4
0.8
C-276
>1
10
11
240
31
0.3
0.6
1
249
FGD
Pulp/Paper
Scrubbers
Bleach washers
Fans
Pulp lines
Ducts
Recovery boiler scrubbers
Dampers
Chemical Process Industry -Inorganics
Dampers
Sulfuric
Fine chemicals
Mist eliminators
Many others
ALLOY 33
Alloy 33 the most recent innovation [12,13], is a chromium-based, fully austenitic wrought
super stainless steel (33 Cr, 32 Fe, 31 Ni, 1.6 Mo, 0.6 Cu, 0.4 N). This alloy has excellent
resistance to both acidic and alkaline corrosive media, mixed HNO3/HF acids, localized
corrosion and stress corrosion cracking. Due to its high nitrogen content, this alloy has excellent
mechanical properties. Its high PRE (Table 3) makes it a very cost-effective alloy in comparison
to the Ni-Cr-Mo alloys such as G-3, G-30 and 625. Its localized corrosion resistance is equal to
or better than some of the Ni-Cr-Mo alloys (Table 6).
Table 10 shows some of the corrosion resistance data of Alloy 33 in various corrosive
environments. In comparison to other high chromium alloys such as Alloys G-30, 690 and 28,
Alloy 33 shows excellent corrosion resistance behavior. This alloy on a cost/performance basis
has the potential of being an excellent alternative to many alloys currently in use such as the 825,
904L, 20, 28, 6Mo alloys, G-3, G-30 and in some cases even Alloy 625. Some of the testing
done with Alloy 33 in sulfuric acid environments, nitration involving nitric acid, phosphoric acid,
acid pickling, nuclear waste reprocessing, and the pulp and paper industry, has shown it to give
excellent results. The alloy has performed exceptionally in concentrated sulfuric acid at high
temperatures as shown by the data in Table 10. Many companies are seriously considering using
this alloy in their various processes.
Table 10. Corrosion Resistance of Alloy 33 and Others in Various Media
Media
Sulfuric Acid
98% H2SO4
Temperature
100C
150C
200C
Alloy
Alloy
Alloy
Alloy
Phosphoric Acid
Temperature
33
G-30
28
690
85% H3PO4
100C
8
12
8
50
154C
43
53
56
Alloy
Alloy
Alloy
Alloy
Mixed Acid
Temperature
33
G-30
28
690
12% HNO3 + 0.9% HF 90C
10
11
230
24
12% HNO3 + 3.5% HF 90C
48
48
>500
252
32% HNO3 + 0.4% HF 90C
11
20
38
58
56% HNO3 + 0.4% HF 90C
66
96
135
187
Table 11. Chemical Composition of Ni-Mo Alloys
Alloy
(UNS No.)
B (N10001)
B-2 (N10665)
B-3 (N10675)
B-4 (N10629)
B-4(C)
(A)
Maximum
Decade
Introduced
Ni
1920s
Bal.
1970s
Bal.
1990s
65(B)
1990s
Bal.
1990s
Bal.
(B)
Minimum
Composition (wt. %)
Mo
Fe
Cr
26-30
4-6
1(A)
(A)
26-30
2
1(A)
27-32
1-3
1-3
27-30
2-5
0.5-1.5
28
3
1.3
(C)
Typical composition
C
0.05(A)
0.01(A)
0.01(A)
0.01(A)
0.006
Ni-Mo Grade
Standard Alloy B-2
UNS N10665
Fe (2% Maximum)
Cr (1% Maximum)
Test Results
Tensile El (%)
ASTM G 30
at 700C after
U-Bend 1 h, 700C
1 h (700C)
10% H2SO4 for 100 h
5
Failure
Potential Hazards
Cracking
SCC
during
during
fabrication
service
High risk
High risk
Controlled-Chemistry
Alloy B-2
UNS N10665
Fe (1.6-2.0%)
Cr (0.5-1.0%)
42
Reduced risk
None
Alloy B-4
UNS N10629
Fe (2-5%)
Cr (0.5-1.5%)
48
Significantly
reduced risk
None Significantly
reduced risk
Reduced risk
Alloy B, the original alloy in the Ni-Mo family, developed in the 1920's, suffered from HAZ
corrosion in nonoxidizing acids (i.e., acetic, formic and hydrochloric) due to its higher carbon
content. In the decade of the 1960's, improved AOD melting technology led to development of
Alloy B-2. This alloy solved the HAZ problem, but suffered from poor fabricability. Recent
developments of controlled chemistry Alloy B-2 (Table 12) and, Nimofer(R) 6629 - Alloy B-4 UNS N10629 - (Table 11 and Table 12) solved both these problems by eliminating/reducing
formation of detrimental intermetallic phases, with further improvement in corrosion resistance
behavior. Table 11 gives the basic developments of the alloys in the Ni-Mo family, and Table 12
shows the improvements in fabricability and corrosion resistance. Greater details on fundamental
behavior and understanding of Ni-Mo alloy systems are presented elsewhere [1,9,10]. Alloy B-2
has been successfully used in production of acetic acid, pharmaceuticals, alkylation of ethyl
benzene, styrene, cumene, organic sulfonation reactions, melamine, herbicides, and many other
products. Alloy B-4, the improved version of alloy B-2, is being tested and considered for
various applications in many other industries.
CONCLUSIONS
The understanding of the role of alloying elements in nickel-based alloys has led to the
recent innovations in both high and low nickel-containing Ni-Cr-Mo alloys. Higher
molybdenum and chromium contents, together with nitrogen fortification, have opened up an
entirely new class of 6Mo alloys with unique properties, and has provided some specific benefits
to industry. A better understanding of the physical metallurgy of Ni-Cr-Mo and Ni-Mo alloy
systems has further contributed to the development of the newer improved alloys, which has
helped to expand the range of usefulness of existing alloys for the modern chemical process and
other industries requiring higher performance levels in the present day aggressive environments.
Alloy 59 many successful applications and its ever increasing specifications in various industries
clearly proves the above facts. A new chromium-based fully wrought super stainless steel (Alloy
33) and the two alloys of the 6Mo family (Alloy 1925hMo and Alloy 31) show excellent promise
of solving many corrosion problems of today's chemical process and other industries in a costeffective manner. The newest alloy of the Ni-Mo family, Alloy B-4 and the controlled chemistry
Alloy B-2 have not only solved the fabricability problems associated with the old Alloy B-2, but
have also improved upon its corrosion resistance behavior.
REFERENCES
1. W.Z. Friend, Corrosion of Nickel and Nickel Base Alloys, John Wiley & Sons, Inc., New
York, 1980, pp. 248-367.
2. R. Kirchheiner, M. Kohler and U. Heubner, A new highly corrosion resistant material for
the chemical process industry, flue gas desulfurization and related applications,
Corrosion/90, Paper No. 90, NACE International, Houston, Texas, USA, 1990.
3. D.C. Agarwal, et al., Cost effective solution to CPI corrosion problems with a new Ni-CrMo alloy, Corrosion/91, Paper No. 179, NACE International, Houston, Texas, USA,
1991.
4. D.C. Agarwal, M.R. Jasner and M.B. Rockel, 6% Mo austenitic stainless steel selection
for offshore applications, Offshore Technology Conference 1991, Paper No. 6598,
Houston, Texas, USA, 1991.
243
5. D.C. Agarwal, et al., The 6% Mo superaustenitics: The cost effective alternative to nickel
alloys, Proceedings first Pan American Corrosion and Protection Congress, Mar del Plata,
Argentina, November 25-30, 1992, Vol. 1, pp. 103-114.
6. M. Rockel and M. Renner, Pitting, crevice and stress corrosion resistance of high
chromium and molybdenum alloy stainless steels, Werkstoffe und Korrosion 35, 1984, p.
537.
7. CroniferR 1925hMo, An advanced high alloy austenitic stainless steel for offshore
hydrocarbon and seawater applications, VDM Report No. 10/2, July 1992, Krupp-VDM,
Werdohl, Germany.
8. U. Heubner, R. Kirchheiner and M. Rockel, Alloy 31-A new high alloyed Ni-Cr-Mo steel
for the refinery industry and related applications, Corrosion/91, Paper No. 321, NACE
International, Houston, Texas, USA, 1991.
9. D.C. Agarwal, U. Heubner, M. Khler and W. Herda, UNS N10629: A new Ni-28% Mo
alloy, Materials Performance 33, 10, 1994, pp. 64-68.
10. D.C. Agarwal, U. Heubner and W.R. Herda, Fundamental considerations during
fabrication and construction of nickel alloy components for CPI, Conference
Proceedings, First International Symposium on Process Industry Piping, December 1417, 1993, Orlando, Florida, USA.
11. Corrosion characteristics and applications of newer high and low nickel containing NiCr-Mo alloys, Conference Proceedings, 12th International Corrosion Congress,
September 19-24, 1993, Houston, Texas, USA.
12. M. Kohler, U. Heubner, K.W. Eichenhofer and M. Renner, Alloy 33, A new corrosion
resistant austenitic material for the refinery industry and related applications,
Corrosion/95, Paper No. 338, NACE International, Houston, Texas, USA, 1995.
13. M. Kohler, et al., Progress with Alloy 33, A new corrosion resistant chromium-based
austenitic material, Corrosion/96, Paper No. 428, NACE International, Houston, Texas,
USA, 1996.
14. D.C. Agarwal, Alloy selection methodology and experiences of the FGD industry in
solving complex corrosion problems: The last 25 years, Corrosion/96, Paper No. 447,
NACE International, Houston, Texas, USA, 1996.
15. D.C. Agarwal and W.R. Herda, Alloying effects and innovation in nickel base alloys for
combating Aqueous corrosion, VDM Report No. 23, February 1996, Krupp-VDM,
Werdohl, Germany.
16. F.E. White, G.K. Grossmann, H. Decking and D.C. Agarwal, Experience with the Use of
Alloy 59 in Industrial Applications, Corrosion/96, Paper No. 433, NACE International,
Houston, Texas, USA, 1996.
244
ABSTRACT
From a corrosion engineering point of view, in spite of common opinion, correctly welded steel
joints are not the weakest points of reliable constructions. The results of long-term tests have shown
the leading role of MMB structure in corrosion crack initiation and propagation. Such a band
structure often exists in weldable steel sheets selected for pressurized systems in the petroleum
industry. A practical aspect of the results reported is connected with steel quality recommendations
for reliable construction. The lack of an MMB structure or an MMB width limited to below 0.01 mm
[1] should guarantee the steels resistance to hydrogen-induced cracking.
Key Words: Segregation band, corrosion cracking, line-pipe steels, branching effects,
hydrogen sulfide
INTRODUCTION
The pressurized installations of the petrochemical industry belong to those most reliable
constructions that minimize the danger of catastrophic failure, sometimes of large-scale
losses. The probability of material failures is (in a simple way of thinking) proportional to the
total length of the pressurized system, e.g., piping-net, pressure vessels, etc. Of course, it also
depends on inspection systems efficiency. Therefore, many petrochemical plants have been
compactly built to minimize the length of piping and energy losses.
However, the history of failure analysis shows that an ideal inspection system does not
exist in spite of serious improvement in testing equipment and maintenance. Thus, the
probability of catastrophic failures increases with plant operation time, as is shown in Fig. 1.
In the past, petrochemical plants were constructed based on the burst-before-leak (BBL)
concept. This concept is no longer acceptable because any of the pressurized installations can
produce a chain-like reaction damaging sometimes costly and vital parts of a compactly built
plant. Many such-constructed plants are still in operation. The accumulation of information
on the environment-material - stress relationships shows that the BBL concept is no more in
use.
Since about 1970, a new concept of leak-before-burst (LBB) has been widely applied in
the designing and engineering calculations for reliable construction. This concept takes into
consideration the role of material flaws in the brittle fracture phenomenon and the influence
of corrosive environments on catastrophic failures. Thus, the materials susceptibility to
245
246
Figure
2b.
Damage
to
Mazur
installations
During the gas-plants operation, the hydrocarbon condensate from time to time also
contained some (about 500 ppm) H2S which was dependent on the actual natural gas sources.
That detrimental compound reacted with the steel, producing internal cracks and
delaminations in the pipe-wall (Fig. 3). The corrosion cracks penetrated into the inner surface
of the pipe-wall, as shown in Fig. 4.
(1)
diffused through the iron crystal lattice decreasing the steels ductility.
A bend test specimen taken from the burst 30 diameter pipe exhibited almost no
ductility (Fig. 5). The fracture surface showed fully brittle features (Fig. 6).
248
Mazur
All mechanical and metallurgical tests clearly showed that hydrogen atoms diffused into
the steel-wall dramatically decreased the steels ductility and produced a great number of
cracks (fissures). During the long period of gas-plant operation, these cracks penetrated
through the pipe-wall cross section until the last steel fiber was broken. At that moment, the
pipe catastrophically burst producing the long opening crack visible in Fig. 2a.
A very detailed material testing of the other pipes operating under the same conditions
during the same period of time (as the burst pipe) also showed the hydrogens action, but it
was limited to a relatively thin layer on the inner surface of the pipe. FeS deposit was found
there, but the steels ductility was still high, according to the standards.
The question is, why one pipe was so greatly affected by hydrogen sulfide (and stresses)
but another one operating in the same environment was not susceptible to corrosion cracking.
The most probable answer was suggested already by Mazur [1], but the next experiments
gave more information about the influence of structural constituents (especially segregation
bands) on the susceptibility to hydrogen crack initiation and propagation in weldable pipeline steels.
SEGREGATION BANDS IN STEELS
During laboratory investigations, two types of segregation bands were found. The first
one was connected with persistent chemical segregations inherited by hot-worked steel after
crystallization. It is well known that the most detrimental elements in steel are sulfur and
phosphorus. Sulfur is present as non-metallic inclusions (sulfides) elongated along the rolling
direction. They act as the traps for diffusing hydrogen atoms through the crystal lattice.
Phosphorus is present in steel as dissolved atoms in solid solution and can be traced
metallographically by the use of special etchants. The Oberhoffer reagent [3] does not react
with steel if the phosphorus content is high (white band) but strongly etches the surface of
low-phosphorus steel. Such a wide macro-micro segregation band (MMB) in pipe-steel with
localized corrosion cracking is shown in Fig. 11.
(MMB)
249
As the MMB becomes wider, the phosphorus concentration should be relatively higher.
Assuming sinusoidal change of the phosphorus concentration in steel, the schematic situation
in two steels of similar average phosphorus content, but different MMB width, is shown in
Fig. 12. The phosphorus concentration in the wide MMB is higher than in the narrow one.
Therefore, the susceptibility of wide MMB to corrosion crack initiation and propagation is
higher because of the embrittling influence of phosphorus. Usually in wide MMB, nonmetallic inclusions are present and act as internal stress-risers, accelerating corrosion crack
initiation and propagation.
The second type of structural band is often observed in ferrite-pearlite hot-worked
weldable steels. An example of such a band structure is shown in Fig. 13 after etching in a
typical solution of 4% HNO3 in alcohol (nital); the dark constituent is pearlite, and the white
is ferrite.
and
250
Mazur
Both types of segregation bands are often present in weldable steels. But from a safety
point of view, the persistent MMB-type should be treated as the weakest area for corrosion
crack initiation and propagation. When the MMB, are wide, the susceptibility of the steel to
corrosion fracture is high. Such a wide MMB with a number of non-metallic inclusions is
shown in Fig. 14. Corrosion cracks are shown by arrows. A different area of the same
specimen, but nital-etched, is shown in Fig. 15. There is visible band structure, but in marked
areas there are also elongated nonmetallic inclusions and microcracks which most probably
belong to the wide MMB. These features are not clearly visible in the micrograph because of
the type of etchant (nital) used. A microprobe linear analysis made across the wide MMB
confirmed an increase in the phosphorus content at these sites (Fig. 16).
CORROSION CRACKS IN WELDED JOINTS
The influence of MMB directionality on corrosion crack propagation was tested on the
arc-welded specimens. For the laboratory tests, an A-52 grade weldable steel was selected.
The calculated carbon equivalent, CE , was 0.38; thus, the ordinary arc-welding procedure
was used. From the welded K-joints (Fig. 17), the crack-opening-displacement (COD)-type
specimens were taken. The MMB structure, with an average width of 57 microns, was
distributed along the rolling direction in the parent steel sheets.
The constant load cantilever bend test [4] for stress corrosion susceptibility measurement
of the welded joints was used. NACE water solution (5% NaCl, 0.5% CH3COOH) saturated
by H2S up to pH 3.5-3.8 acted on a short fatigue precrack made at the mechanically cut Vnotchs front. The COD specimens were taken in such a manner (Fig. 18) that precracks were
likely to initiate corrosion cracks in different zones of the welded joint, i.e., fusion zone (FZ),
heat affected zone (HAZ) and parent metal (PM).
At the beginning, the lowest stresses acted on the precracked notch. As the test time was
increased, the real cross section decreased due to corrosion crack propagation. Thus, the
stresses that acted at the crack front steadily increased. Therefore, at the beginning of testing
and because of low stresses, corrosion crack propagation was controlled by a dissolution
mechanism. At some crack distance, when the crack length was long enough, its propagation
became controlled by a mechanical factor (stress).
251
Figure 19. Branching process starting at point A in the parent metal (unetched)
Figure 19 shows the branching effect in parent metal. From point A, the primary
corrosion crack split into two branches parallel to the rolling direction. The most interesting
observations were found for the specimens with a V-notch placed in a heat-affected zone
(HAZ). The micrograph shown in Fig. 20 was taken for a specimen not fully broken during
corrosion crack propagation
After using Anczyc etchant [5], revealing MMB as black bands, it is quite clear that up
to area A the corrosion crack propagated as a wide fissure perpendicular to the specimens
surface; similar to the primary crack shown in Fig. 19. From point A (Fig. 20), the primary
corrosion crack split into two cracks parallel to the rolling direction. One very short branch
was arrested by the fusion zone where no band structure exists, but the longer crack
propagated towards the parent metal along the MMB. As the time of the corrosion test was
increased, these long cracks, parallel to the rolling direction cracks and propagated in the
wide bands, joined the deeper placed MMB by short step-wise cracks visible in area B (Fig.
20).
252
Mazur
At some distance of the corrosion cracks in the cross section, the critical stress-intensity
factor (KIC) was reached and the specimen had to break by fast fracture mechanism. After
branching, the corrosion crack rate became constant due to stress reduction at the multiplied
crack fronts in spite of the increasing values of the stress-intensity factor (KIi). The
da
and KIi is shown in Fig. 21.
relationship between the corrosion crack rate
dt
Figure 20. Primary corrosion crack perpendicular to the specimens surface; the crack
initiated in the HAZ and split into two longitudinal branches with the longer
branch propagating towards the PM and the shorter one towards the FZ (Anczyc
etchant)
253
In all tested specimens, a dominant role of the MMB structure in branching was found.
The corrosion cracks always propagated towards the parent metal where MMB existed, but
the branches propagated towards the weld-bead were arrested due to the lack of MMB
structure there. Therefore, the corrosion cracking of the weldable steels depends on more or
less developed MMB structure. With greater MMB width, is greater the steel is more
susceptible to corrosion crack initiation and propagation.
The results of KISCC measurements for specimens with precracks (notches) placed in the
three different zones of welded joints have shown that parent metal (steel sheet) exhibited the
highest susceptibility to corrosion cracking in terms of a KISCC to KIC ratio that was 0.72 only.
For HAZ and FZ this ratio was close to 1.0, i.e., both zones are nearly immune to applied
environment and stresses. Most of the published results did not analyze the role of structural
bands in branching effects. Published micrographs of branching cracks [6] most probably
have propagated along the rolling directions of austenitic steels and high strength aluminium
alloys.
ACKNOWLEDGMENT
This research was partially sponsored by The University Status Research Fund of The
Academy of Mining and Metallurgy, Krakow, Poland.
REFERENCES
1.
2.
3.
4.
5.
6.
254
ABSTRACT
The fluid catalytic cracking unit (FCCU) is one of the most profitable process units in the
petroleum refining industry. The FCCU converts less valuable heavy hydrocarbons into lighter, more
valuable components by cracking the larger molecules in the presence of a catalyst. During the
conversion process, many highly corrosive chemical species are evolved from the catalytic reactions.
One of the principal areas of the FCCU that comes into contact with such corrosive chemicals is
the unsaturated gas concentration section. This section receives corrosive hydrocarbon gases from the
FCCU Fractionation section, which come into contact with various pieces of equipment. This paper
describes the economic penalty of frequent shutdowns or reduced throughput that have been caused by
this type of corrosion at the Jeddah Refinery.
The specific example addressed in this paper is corrosion of the wet gas compressor interstage
and high-pressure coolers. This costly problem was resolved by a simple and easy solution over
several other more costly alternatives. The solution that was selected involved proper distribution and
adjustment of water wash to the shell side of the interstage and high-pressure coolers. This water also
serve to prevent the disposition of ammonium chloride salts on the external surfaces of the cooler
tubes.
Key Words: Fluid catalytic cracking unit, molecules, catalyst, conversion process,
unsaturated gas concentration section, shutdowns, ammonium chloride
INTRODUCTION
Equipment deterioration is one of the major expenses in the petroleum refining industry.
This problem can have several different causes, but is generally mechanical (erosion) or
chemical (corrosion) in nature. This paper describes one of the corrosion problems that
occurred in the fluid catalytic cracking unit (FCCU) at the Jeddah Refinery.
This corrosion problem caused throughput reductions, safety hazards, equipment
deterioration and high maintenance costs. The resolution of the problem took several years to
identify the causes, and to develop and implement corrective action. In the end, the solution
was very simple and easy to implement.
255
DISCUSSION
The Jeddah Refinery is located in the city of Jeddah, Kingdom of Saudi Arabia. The
majority owner and operator of the refinery is Saudi Aramco, which is the worlds largest
company in the petroleum industry. The Jeddah Refinery processes light and heavy Arabian
crude oil, and has a capacity of 90,000 bbls/day. The major process units consist of
Atmospheric and Vacuum Distillation, Hydrodesulfurization, Catalytic Reforming, and
Catalytic Cracking units. The unit under discussion in this paper is the Fluid Catalytic
Cracking Unit or FCCU.
Feed
The FCCU processes a variety of different feedstocks, basically from Vacuum
Distillation units at the Refinery, and from the Lube Oil Refinery located adjacent to the
refinery. The feedstocks include heavy vacuum gas oils, slack waxes, and 100 SUS distillate.
Types of Corrosion in FCCUs
Several types of corrosion can take place in FCCUs. The types can be grouped into two
major categories [1]:
Hydrogen charging; and
Carbonate cracking
Hydrogen charging includes sulfide cracking, blistering, hydrogen induced cracking, and
stress-oriented hydrogen-induced cracking.
Carbonate cracking is also known as
intergranular stress corrosion cracking.
Table 1. Materials of Construction of Coolers
Cooler Part
Shell & Heads
Tube Sheet Stationary &
Floating
Tubes ( Straight Type)
Material
A-515 Gr.60 (CS for high temp service)
A-181 Gr. I (Rolled Steel)
ASTM B-111, No. 687 (Cu-Ni Alloy)
The first stage compressor discharge is cooled by two parallel banks of exchangers,
each consisting of two exchangers operating in series, labeled G-E1 A/B/C/D.
The second stage compressor discharge is also cooled by two parallel banks of
exchangers, each consisting of two exchangers operating in series, labeled G-E2
A/B/C/D.
Seawater passes through the tube side at lower pressure than the hydrocarbon gases
that pass through the shell side.
All coolers are TEMA type AES, which consist of four tube passes per cooler.
256
Halawani
258
Halawani
Several potential causes of the corrosion problems were discussed with a reputable
consultant. The areas considered included:
RECOMMENDATIONS
The following recommendations were considered for this corrosion problem:
meters/Second;
Installation of sacrificial iron anodes on the channel and floating heads;
Injection of a filming inhibitor, i.e., iron sulfate (FeS04), into the wash water;
Removal of foreign materials from the seawater by filtering;
Installation of plastic inserts at tube inlets to prevent erosion;
Eddy current examination during the inspection of the unit,
Review of the design of the floating head;
Checking of the hardness of the bolts which should be less than 235 BHN
(Brinnel Hardness Number);
Changing of tube material to a corrosion-resistant type. (i.e., titanium).
Many recommendations were made, but one very important process related point was not
taken into consideration. This point concerned the water wash to the compressor coolers to
wash off ammonium chloride salts and other corrosion species.
259
260
Halawani
Originally, the total volume of wash water was routed to the first stage intercooler. In
checking the existing system, it was determined that one-half of the total wash water quantity
was sent to another user (M/C overhead cooling system). This caused the amount of wash
water sent to the interstage coolers to be half of the recommended quantity (20 gpm). This
deviation was corrected by injecting the recommended wash water quantity to the first stage
intercooler and by installing restriction orifices on each of the parallel cooler trains (Fig. 2).
CONCLUSIONS
After careful consideration, the following steps were taken to correct the corrosion
problems in the FCCU wet gas compressor interstage and high-pressure coolers:
1. The wash water rate was adjusted to 20 gpm as provided for in the original design.
2. Restriction orifices were installed on each branch to ensure equal distribution of wash
water to each branch.
After completing these actions, only very rare leaks have been observed in the
compressor interstage and high-pressure coolers. In summary, when troubleshooting
problems, all related items must be taken into consideration, even if they appear to be very
minor at the time. Obviously, it was much less expensive to adjust the wash water rates and
distribution than to install titanium bundles, which was one of the recommendations
considered.
REFERENCES
1. R.C. Strong, V.K. Majestic and S.M. Wilhelm, Basic steps lead to successful FCC
corrosion control, NALCO Reprint SL-47 (reprinted from Oil and Gas Journal), Sept.
30 and Oct. 7, 1991.
261
ABSTRACT
The high-pressure Kero hydrodesulfurizer reactor in the Shuaiba Refinery of the Kuwait National
Petroleum Company was commissioned in 1968. By 1973, routine inspection revealed small cracks
up to 3/16 in. (4.8 mm) deep which gradually increased in size necessitating weld repair in 1981.
However, subsequent inspection in 1985 revealed reappearce of the cracks, and by 1990, the cracks
were about 1 in. (25.4 mm) deep and 13 in. (330.2 mm) long. This reactor was built in the 1960s
without adequate control of the chemistry (J-factor) and impact properties to reduce temper
embrittlement. In view of the this and possible damage due to hydrogen embrittlement after 20 years
of service, further in-situ repair by welding was ruled out. Instead, a fitness-for-purpose study was
made utilizing recent developments in fracture mechanics techniques and available software to ensure
safe and reliable operation by pressure down rating the reactor.
Key Words: Kero hydrodesulfurizer reactor, J-factor, temper embrittlement, hydrogen
embrittlement, fitness-for-purpose, fracture mechanics
INTRODUCTION
Chromium-molybdenum steels used for the construction of hydro-processing reactors are
known to undergo material degradation in service. The most important material degradations
are temper embrittlement and hydrogen embrittlement. The first generation of reactors, built
in the 1960s when the current controls on chemistry and impact properties were not exercised,
are prone to temper embrittlement. Therefore, when cracks are found in a reactor during
routine inspection, an assessment to predict the continued safe and reliable operation of the
reactor requires serious consideration. In the past, in the absence of adequate tools to
quantify the impact of such defects, plant engineers faced difficult decisions in such
circumstances. The decision, in some cases, may be very conservative requiring long-term
plant shutdown for costly repair/replacement. The availability of computer softwares and
standards providing guidance on methods for assessing the acceptability of flaws, e.g., British
Standard BSI PD6493 and other such standards, have provided engineers with much needed
tools upon which a more careful recommendation can be based for continued safe operation
of such equipment. This paper describes the assessment and current status of the cracks
found in a Kero hydrodesulfurizer reactor at the Shuaiba Refinery, Kuwait National
Petroleum Company, and highlights the importance of such assessment techniques.
CONSTRUCTION AND HISTORY OF THE REACTOR
263
(1)
Flaw dimensions, as found by UFD, were grouped as per the guidelines provided
in BSI Standard PD 6493 [3].
264
Askari et al.
265
266
Askari et al.
Figure 3. FAD for the existing crack under 2800 psig for A387-D (level 1)
Geofac software licensed by the Fracture Search Inc. [4] was utilized for
calculation of the M factor for the existing crack.
Fracture toughness data was obtained from the co-relation given in PD 6493 [3]
between fracture toughness and charpy V-notch values, where the charpy V-notch
values were measured by removing boat samples from a similar reactor.
The analysis was carried out for both high-pressure operation at 2800 psi (19.3 Mpa) and
medium-pressure operation at 1300 psi (8.96 Mpa) at level 1, which is a somewhat
conservative assessment. The analysis was done for both materials, i.e., 2HS and SA 387 Gr
D as the cracks were present at the weld between these two materials. The fracture analysis
diagrams (FADs) for the 387Gr D material are presented in Figs. 3 and 4. As can be seen
from the FAD, the cracks are considered to be safe from failure by brittle fracture at 1300
psig (8.96 Mpa) operation, but not safe when the pressure is raised to 2800 psig (19.3 Mpa).
267
Figure 4. FAD for the existing crack under 1300 psig for A387-D (level 1)
ASSESSMENT FOR HYDROGEN EMBRITTLEMENT
The second assessment was done for the combined effect of hydrogen embrittlement and
temper embrittlement, as several studies have shown that the threshold stress intensity for
cracking in hydrogen (i.e., KIH) can be appreciably reduced in steel that has been subjected
to prior temper embrittlement. Wadate et al. [5] have provided a correlation between KIH
and embrittlement properties measured by fracture appearance transition temperature (FATT)
as follows:
KIH = .0014 FATT 2 - 0.421 FATT + 57.0
where KIH is expressed in Mpa
(2)
In the absence of actual data on FATT, the correlation between the J-factor i.e., (Si +
Mn) x (P + Sn) x 10-4 and FATT has also been provided [6].
Table 1. Data Analysis for the Existing Crack Under 2800 psig for A387-D (level 1)
268
Askari et al.
Table 2. Data Analysis for the Existing Crack Under 1300 psig for A387-D (level 1)
269
In the present study, a detailed chemical analysis was done for boat samples removed
from a similar reactor which has a similar manufacturing and operating history. This resulted
in a J-factor of 350, and a corresponding KIH of 30 MPa m0.5 after 100,000 hours of
operation. The stress intensity factor (KIc) for 1300 psi (8.96 Mpa) operation was calculated
to be 35.6 Mpa m0.5 for the worst crack present.
Since KIc > KIH the cracks are of the propagating type. However, the rate of crack
-24
11.7
-6
DISCUSSION
From the above analysis, it was concluded that the reactor was not safe for operation at
its originally designed pressure of 2800 psi (19.3 Mpa) (Fig. 3 and Table 1). However, it was
considered safe to operate at 1300 psi (8.96 Mpa) (Fig. 4 and Table 2) at which the plant was
found to be still capable of producing products to standard specifications. At 1300 psi (8.96
Mpa) operating condition, from a hydrogen embrittlement point of view, the chances of crack
growth is a possibility, but as the rate of crack growth is found to be quite low, it was
considered safe to operate the reactor by down grating the pressure to 1300 psig (8.96 Mpa).
No significant crack growth could be detected after operating at the lower pressure of 1300
psig (8.96 Mpa) between last two UFD inspections made in 1992 and 1995. It is, however,
fully recognized that in the event of further crack growth, in-situ welding repair will not be
possible due to the metallurgical degradation of the reactors materials. Also, due to the more
stringent specifications required for kerosene in respect to smoke point (i.e., 28 mm
minimum), the reactor needs to be operated at high-pressure at around 2300 psi. Our analysis
shows that with the existing crack, operation of the reactor will not be safe at 2300 psi.
Accordingly, it has been decided to procure a new reactor for operation at 2300 psi. Till such
time, the reactor will continue to operate at 1300 psi with run-to-run monitoring by UFD.
CONCLUSIONS
The above discussion highlights the advantages offered by fracture mechanics techniques
for finding acceptable solutions at the plant level. Such solutions can be achieved by
analyzing the fitness-for-purpose of the equipment to continue operation without
compromising the safety and integrity of such important equipment.
ACKNOWLEDGMENT
The authors wish to thank the management of KNPC for permission to publish this
paper. Encouragement and support provided by Refinery Manager Mr. A.L. Al-Houti is
sincerely acknowledged.
REFERENCES
1. Viswanathan, Damage Mechanisms and Life Assessment of High Temperature
Components, ASME International, Ohio, 1989, pp. 21-57.
2. Crackwise Software, The Welding Institute (TWI), UK.
270
Askari et al.
271
ABSTRACT
A high-pressure warm-separator (HPWS) off gas air cooler made of Incoloy 800 failed at one of
its inlet nozzles. Inspection and nondestructive testing (NDT) showed cracks in the shape of sun rays
surrounding the weld of the chemical cleaning nozzle connected to the inlet nozzle. Chemical
analysis, metallographic examinations, and microhardness measurements indicated that the cracks
were due to polythionic acid stress corrosion cracking. Cracking was promoted by the presence of
carbide precipitation and residual stresses resulting from the manufacturing and welding practices.
Key Words: Polythionic acid, stress corrosion cracking, Incoloy 800, case study, failure analysis
INTRODUCTION
An atmospheric residue desulphurization unit (ARDS) was commissioned in the early
1988 as a part of the modernization project of Mina Abdulla Refinery. The unit is designed
to process 65,900 BPSD of atmospheric residue. At the heart of the unit is a pair of parallel
fixed-bed reactor trains containing desulphurization catalyst. The chemical basis for the
process is the catalytic reaction of hydrogen with sulfur-containing hydrocarbons to produce
sulfur-free hydrocarbon and hydrogen sulfide. The incoming residue feed is preheated by
exchange with the reactor effluent and a fired heater. The feed is mixed with hot-recycled
gas, and is sent to the reactor where it is desulphurized. Finally, the reactor effluent goes to a
series of separators to release the dissolved light ends (Figs. 1 and 2).
The high-pressure warm-separator (HPWS) off gas air cooler consists of a series of eight
banks air cooler, operating at 180C under a gas pressure of 21 bar, and handling a mixture of
H2, NH3, H2S and hydrocarbon. Each bank has two inlet and two outlet nozzles, 4 in.
diameter. There are two chemical cleaning nozzles, 1.5 in. diameter, per bank, one of each in
the inlet and outlet nozzles. The air cooler headers, nozzles and tubes are all made of Incoloy
800 in accordance with ASTM B 407-UNS-N08800 (see Tables 1 and 2). Wash water is
injected into the air cooler effluent to prevent the deposition of solid ammonium salts (i.e.,
NH4Cl and NH4OH). The ammonium salts are readily removed by the wash water (see Table
3).
273
Figure 2. A schematic diagram of high pressure warm separator off gas air cooler (HPWS)
275
Elongation (%)
30
Amount (%)
30-35
19-23
39.5
1.5
0.75
1.0
0.015
0.15-0.60
0.15-0.60
Amount
3.0
0.05
0.10
0.10
0.10
1.0
7.0-8.0
5.0
and welding technique. Hydrogen embrittlement of the HAZ developed under normal
operating conditions leading to weld cracking and subsequent leakage.
Repair of the cracked headers of the eight banks is impractical, costly and not guaranteed
to lead to solving the problem. Furthermore, the use of the remaining uncracked banks is not
advisable given the potential for similar problems. They are also not recommended for
reconditioning for the same reasons. It was recommended to use a completely new air cooler
with improved design. The new air cooler was fabricated from Incoloy 800, in a similar
manner to those used in other neighboring refineries.
CRACKING IN INCOLOY 800 OFF GAS AIR COOLER NOZZLE
The new air cooler made of Incoloy 800 conformed to ASTM B 407-UNS 08800. It was
delivered in 1992 and was installed to replace the then existing carbon steel air coolers. In
early January 1995, one four inch diameter inlet nozzle of one of the air cooler banks leaked
during start-up of the unit after a maintenance shutdown. The leak was located around the
weld of the 1.5 in. diameter chemical cleaning nozzle connected to the 4 in. diameter inlet
nozzle. All 32 inlet and outlet nozzles, 16 of which had chemical cleaning nozzles, were
checked with fluorescent dye, and 8 more 4 in nozzles were found to have cracks. Nine
nozzles (inlet and outlet) were totally replaced with 321 stainless steel. The new nozzles
were not provided with chemical cleaning nozzles.
Metallography and microhardness tests were carried out to determine the reason for
failure. Some sections were given to an outside consultant and to the manufacturer.
Initial Observations and Nondestructive Testing (NDT)
The leaky 4 in. diameter nozzle was removed from the header and the internal surface
was checked with fluorescent dye. Cracks were observed on the internal surface of the 1.5 in.
diameter nozzle weld. The cracks were seen to initiate from the weld toe and were
perpendicular to the weld (Fig. 3).
Cracks were also observed in the 4 in. diameter nozzle at the wall deposit to the weld.
Small indications of cracks were also noted at the nozzle-to-flange weld.
The leaky 4 in. diameter nozzle was first cut longitudinally into two halves. The half
containing the 1.5 in. nozzle was further cut and one quadrant was given to the representative
of the designer, while another identical quadrant was used for the in-house investigation. The
other half was preserved for further analysis by an outside party.
Metallography
The in-house sample containing cracks was first cut longitudinally. It was then cut into
two transverse cross sections. The first sample revealed intergranular corrosion of the base
metal (i.e., in the 4 in. diameter nozzle). Severe carbide precipitation was noticed at the grain
boundaries (Fig. 4). The examined section was away from the weld. Severe disintegration
and also loss of grains was also noticed (see Fig. 5), rendering the structure very weak. The
ASTM grain size was found to be 4.5-5. Also, the microhardness of the base metal was 169
BHN, which is considered normal.
277
The second sample revealed intergranular cracking in the longitudinal cross section. The
cracks were in the base metal (i.e., in the 4 in. diameter nozzle). The cracks were noticed to
initiate from the weld toe and to travel to the other edge through the base metal (Fig. 6).
Carbide precipitation, disintegration and loss of grains were observed once again . The
ASTM grain size of the second sample was 4.5-5 and the mircrohardness of the base metal
was 165 BHN, which is considered normal. The second sample also revealed intergranular
corrosion and cracking on the transverse cross section. The cracks appeared to propagate
along the grain boundaries. Carbide precipitation, disintegration and loss of grains were also
noticed within the examined cross section.
Fractography
The fractured surfaces were examined using scanning electron microscopy (SEM).
Crystalline facets were noticed (Fig. 7), especially in the region of crack initiation.
Figure 7. SEM fractograph showing separated grain facets and secondary cracking
Chemical Analysis
The chemical composition analysis confirmed that the material was identical in
composition to Incoloy 800. Energy dispersive spectroscopic analysis revealed the presence
of sulfur.
Reasons for Failure: Analysis and Ven Diagram for Stress Corrosion Cracking
Intergranular corrosion (IGC) of the base metal (i.e., 4 in. diameter nozzle) indicated that
carbides had precipitated on the grain boundaries during the manufacturing process, because
280
the operating temperature of 340F is too low for such precipitation to occur during service.
Precipitation of carbides also occurred in the HAZ during welding, as was observed during
the examination.
All 1.5 in. diameter chemical injection nozzles were replaced at the time of installation
due to the leakage of the original nozzles during hydrotesting. This resulted in the HAZ
being affected twice. However, IGC was noticed on the base metal far away from the weld
which confirms the existence of microstructural deficiencies during manufacturing.
Precipitation of carbides makes the grain boundaries prone to corrosion and cracking.
The presence of a corrosive medium such as polythionic acid would promote corrosion of the
grain boundaries under such conditions. The presence of IGC suggested the formation of
such acid during shutdown, which is very likely in the absence of neutralization before
shutdown. Although Incoloy 800 is considered superior to austenitic stainless steels, it is still
susceptible to polythionic acid corrosion attack and the system should be neutralized before
opening, as recommended in NACE RPO1-70-93. Understandably, the presence tensile
stresses is required to initiate and propagate cracks along the corroded grain boundaries. In
the present case, stresses can be present in the form of residual stresses as a result of the
manufacturing practices and welding. Furthermore, the 1.5 in. diameter nozzle welds
appeared under bending stress.
CONCLUSIONS
The material (Incoloy 800) was received in a sensitized condition which is considered to
be inferior and unacceptable. Welding of the chemical cleaning nozzles considerably affected
the HAZ. Formation of polythionic acid during shutdown promoted the IGC process.
Indeed, energy dispersive analysis confirmed that sulfide was present. The pattern of
cracking was consistent with the radial stress around the weld. Based on the investigation, a
recommendation was made to recheck all the 4 in. inlet and outlet nozzles for cracking with
fluorescent dye penetrant as well as the 321 stainless steel. Considering the hazards involved,
it was preferable to replace all of the original Incoloy nozzles, even if they were not cracked.
Because there was a strong possibility that all nozzles from the same manufacturing batch
would contain harmful precipitations, in-situ metallography (replica) was highly
recommended for all the nozzles and headers to determine the presence of carbide
precipitation. Thus, a firm specialized in the field of in-situ metallography was hired to test
all of the inlet and outlet nozzles, headers, drains, vents and tubes.
281
ABSTRACT
Tube heaters (THs) in oil refineries play a strategic role in heating hydrocarbons. However, they
may suffer from corrosion damage if service conditions differ from those they are designed to operate
under and/or if not enough attention is given to the composition/heat treatment of the tube materials
and the composition of the combustible products.
We experienced this problem with a cylindrical vertical heater made from convection tubes made
of material ASTM A106, and radiation tubes made of ASTM 335 Gr P11. After seven years in
service, the heaters tube surfaces showed severe crevice corrosion damage. A number of analyses
and tests were carried out to study the materials characteristics and to compare them with those of a
sound heater. Tests included metallurgical analysis, microhardness, grain compactness, carbon
concentration and chemical analyses of the combustible products.
This paper describes the results of each testing technique and identifies the origin of the
corrosion damage as grain compactness/heat treatment and the presence of corrosive agents in the
combustible products and in the air mixed with vapours coming from a nearby cooling tower.
Key Words: Tube heaters, hydrocarbons, corrosion, grain compactness, combustibles.
INTRODUCTION
Tube heaters (THs) are widely used in the process of refining crude oils. Different
products are extracted at different temperatures: Naphtha up to 200C, Kerosene between
200C and 300C, and Diesel between 20C and 380C. Other extracted products are usually
referred to as fuel. To reach these temperatures, a number of heating methods are used.
Steam heating,
Electrical heating,
Heat exchangers, and
By direct firing (THs).
THs are chosen when other methods fail to give the desired elevated temperature or for
economical reasons. They were first invented in the USA at the beginning of the 20th century
and are classified either by their heat transfer method, i.e., radiation or radiation/convection,
or by their external appearance, i.e., box heaters, cell heaters, cylindrical heaters, etc. The
tube materials used in these heaters are usually: A 335 Gr P11 (1 Cr Mo), ASTM A 200
Gr P 22 (2 Cr Mo), A335 Gr P5 (5% Cr, Mo), or A106 Gr B. The combustibles used
283
are fuel gas, fuel oil or natural gas. In the literature, corrosion damage of THs is well
documented [1,2]. Most authors agree on the following causes:
(kg/cm G)
Steady State
TH1
TH2
452
400
225/355
280
27.0
39
21.16-23.7
29
HC + H2
Oil + H2
+ light HC
A335 Gr P11 A335 Gr P11
141.3 x 6.6
88.9 x 7.62
1972 - to date 1983 - to date
315/504
507
90% H2+10%
CxHy
0.8 max
0.8 max
Start-Up State
TH1
TH2
200
200
H2
H2
Natural gas
+ Hydrogen
Although the two furnaces appear to be identical, the corrosion damage in TH2 is very
pronounced compared to that in TH1.
Visual Examination
284
Attou et al.
After 60,000 hours of service, the outer surface of the tubes of TH1 showed a layer of
black scale 0.4 mm thick (Fig. 1). The corrosion rate was estimated to be 0.06 mm per year.
This is the usual oxidation/decarburization mechanism.
Black Scale
Oxide Layer
Base Metal
Base metal
2. H2-filled voids
3. Sulphur deposits
1. Oxide layer
Figure 2. Schematic diagram showing the degradation mechanism of the TH2 tubes
Metallographic Examination
The examination results for TH1 and TH2 (Figs. 3 and 4, respectively) are given in
Table 2.
285
TH 1
Black scale 4 mm thick
Decarburization up to 0.25 mm
TH 2
Idem
-
Ferrite-Pearlite normalised
0.041
0.088
512
128
TH1
(Reforming Gas)
<150
<10
86.95
6.28
3.88
2.27
0.33
0.05
-
H2S
(ppm)
HCl
(ppm)
H2
(% vol)
C1
(% vol)
C2
(%vol)
C3
(% vol)
C4
(% vol)
C5
(% vol)
N2
He
* The TH2 fuel is a mixture of 95% vol. natural gas + 5%
vol. hydrogen fuel-gas
286
TH2
(Natural Gas)*
>150
83.54
7.656
1.951
0.544
0.199
5.621
0.19
Attou et al.
DISCUSSION
The Nelson curves, Fig. 5, as compiled in API 941[2] indicate the safe area of operation
for carbon steel and low alloy steel, as related to hydrogen partial pressure and temperature.
Referring to these curves and the operating conditions in Table 1, it can be stated that both
THs operate safely as regard to hydrogen damage.
However, the presence of H2S in the combustible product of TH2, acts as a catalyst in
maintaining H2 in the atomic state, which diffuses easily in the relatively coarse grain
structure [3]. The accumulation of H2 in voids, many of which form at grain boundaries,
results in the development of high stresses that ultimately blister the metal (Fig. 6).
1.Oxide
2.Blistered surface
3.Moisture + sulphates = H2SO4
mm deep. However, one of the furnaces revealed additional corrosion damage in the form of
surface blistering. A number of tests were carried out and indicated the following causes:
1. Presence of H2 and H2S in the combustible product,
2. Low grain density, i.e., coarse grain structure of tube materials,
3. Position of the heater near a cooling tower which favors vapors condensation
during shutdown periods, and
4. Number of stop-start cycles.
REFERENCES
1. J. Baas and R. Warner, How much life is left in your olefin unit ?, Hydrocarbon
Processing, December 1992, pp. 81-87.
2. API Publication 941, Steel for Hydrogen Service at Elevated Temperatures and Pressures
in Petroleum Refineries and Petrochemical Plants, 4th edition, April 1990.
3. A.C. Million, L'Hydrogene dans les aciers et dans les joints souds, DUNOD, Paris 1971.
4. Fired heaters and stacks, Guide for Inspection of Refinery Equipment, 2nd edition, 1976,
Chapter 1X, API, 1976.
5. J.A. Dean, Langes Handbook of Chemistry, 13th edition, McGraw-Hill Company, 1972,
pp. 6-33.
288
ABSTRACT
The super duplex stainless steel grade UNS S32750 is presented as a candidate material for
seawater-cooled heat exchangers. Due to its duplex structure, with roughly equal amounts of ferrite
and austenite, the material possesses high strength and superior resistance to erosion-corrosion. In
addition, the high alloying content of the material gives rise to excellent resistance to pitting and
crevice corrosion as well as to stress corrosion cracking (SCC).
The benefits of a super duplex stainless grade for this type of application are reviewed, mainly as
a comparison with other materials such as different copper-based alloys, low alloyed stainless steels
and titanium. The better resistance to erosion-corrosion is emphasized as well as a close description of
why stainless steels, despite the fact that their thermal conductivity is much lower than that of copperbased alloys, still can compete as heat exchanger material in systems operating with seawater as a
cooling medium.
Key Words: Seawater, heat exchangers, super duplex stainless steel, erosion, heat
transfer, corrosion resistance
INTRODUCTION
Selecting a proper tube material for heat exchangers working with seawater as a cooling
medium is a difficult task. Traditionally different copper-based alloys such as brasses,
bronzes and copper-nickel alloys as well as carbon steels have been used most extensively.
For severe steam-side environments high alloyed nickel-based alloys or titanium have been
chosen. In applications where copper-based tubulars have failed, the stainless steel grade
UNS S32750 (SAF 2507) is an alternative to the more expensive titanium and nickel based
alloys for retubing.
UNS S32750 is a high alloyed super duplex stainless steel, with excellent material
properties. Together with high strength, hardness and resistance to erosion-corrosion, UNS
S32750 possesses excellent resistance to localized corrosion such as pitting and crevice
corrosion as well as stress corrosion cracking (SCC), in a seawater environment. The
chemical composition and mechanical properties of UNS S32750 are given in Tables 1 and 2
below.
Seawater Corrosion
Cr
25
Ni
7
Mo
4
N
0.3
Rp1.0 (min)
640Mpa
Rm
800-1000 MPa
A (min)
25%
Hardness (Vickers)
Average 290
SEAWATER
It is often stated that the composition of seawater is more or less the same world-wide.
The variation is, however significant. The total dissolved solids, mainly sodium chloride,
vary from approximately 8000 ppm in the Baltic Sea to 60,000 ppm in bay areas of the
Arabian Gulf. The composition on which artificial seawater is based is about 35,000 ppm
total salt which is a typical value for most seawater. The pH value in the water is
approximately 8. Seawater temperature varies between only a few degrees Celsius at great
depths and in the polar regions, and 30-35C in areas close to the equator and in the Arabian
Gulf. When studying the corrosiveness of seawater, the main environmental factors are
chloride content, pH, temperature, residual chlorine and oxygen contents, fouling, and
galvanic and biological action as well as flow rate. In addition, the presence of impurities,
mainly sulphides, must be considered for copper-based materials used in heat exchangers
with seawater as cooling medium. The situation regarding polluted seawater will be dealt
with below.
The nominal saturation for dissolved oxygen in seawater is about 6-8 ppm at 25-30C.
At higher temperatures the oxygen content decreases, and at lower temperatures it increases.
The dissolved oxygen may also decrease to essentially zero due to bacterial action or
biological or chemical oxygen demand. Copper-based alloys as well as stainless steels
perform best in water having enough oxygen to keep fish alive (3-4 ppm) [1]. However,
copper-based alloys do not stand up well in polluted seawater, in which dissolved oxygen has
been consumed in the decay process and sulphides are present. However, tubes of UNS
S32750 or titanium can serve successfully in such water.
Polluted Seawater
The deleterious effect of sulphides on the corrosion resistance of copper-nickel alloys in
seawater has been reported by many investigators [2]. The most important parameters,
excluding the dissolved sulphide content, affecting this behavior include the hydrodynamic
conditions, oxidation products of dissolved sulphide, pH value, degree of turbulence,
exposure time and effects of chlorine and other pollutants such as ammonia. The oxidation of
dissolved sulphide by molecular oxygen not only results in a decrease of the oxygen
concentration available for corrosion but also may cause considerable change in the pH of the
environment [3]. The corrosion rates of both copper-based alloys and stainless steel grades
are dependent on pH, making pH control of the water a major concern for operating units.
Dissolved sulphide ions greatly reduce the corrosion resistance of Cu-Ni alloys in
aqueous systems. This effect, in flowing deoxygenated seawater, was shown by MacDonald
et al. [3]. Only a low concentration of dissolved sulphides (<0.85 ppm) is necessary to cause
a dramatic decrease of the polarization resistance. In the case of a 90Cu-10Ni alloy, this
sulphide concentration was sufficient to lower the polarization resistance by a factor of 8,
whereas for a 70Cu-30Ni alloy it was lowered by a factor of 70. Higher sulphide levels have
little further impact.
The upper sulphide concentration limit for copper-based alloys is controversial. Lee et
al. [4] found that 0.1 ppm and even lower levels of sulphide are detrimental to copper-nickel
alloys, and Carew and Islam [5] showed that small additions of sulphides dramatically affect
the resistance to erosion-corrosion of copper-nickel alloys. In contrast to this, Woods et al.
[6] concluded that 90Cu-10Ni alloys exposed in partially aerated and deaerated seawater
containing up to 8 ppm sulphides did not suffer from corrosion attacks but instead built up a
protective layer of Cu2S.
Brasses have better resistance to sulphide-induced corrosion than Cu-Ni alloys have, but
not as good as stainless steel in general and UNS S32750 in particular. UNS S32750 may
also suffer from sulphide-induced corrosion attacks under certain circumstances but not at the
levels expected in even highly polluted seawater. Tests performed in NACE solution (5%
NaCl and 0.5% CH3COOH and saturated with H2S) at room temperature, an environment
much more aggressive than polluted seawater, have shown that UNS S32750 is very resistant
to sulphide-induced cracking. No cracking occurred on the UNS S32750 samples irrespective
of the applied stress. Depending on the sulphide and oxygen levels in the water, at pH levels
far below 4, sulphides may initiate corrosion of UNS S32750. This situation is, however,
most unlikely to occur in seawater-cooled heat exchanger systems, and no such case has so
far been reported.
Microbially Induced Corrosion (MIC)
Microbiological biofilms develop on all surfaces in contact with aqueous environments
[7]. Water temperature, pH, content of organic and inorganic ions affect the microbiological
settlement. MIC is used to designate corrosion caused by the presence and activities within
biofilms. The reactions are usually localized and can include sulphide, acid or ammonia
production as well as metal deposition, oxidation or reduction.
Copper-based alloys are vulnerable to biocorrosion. Differential aeration, under deposit
corrosion and cathodic depolarization are some of the reported corrosion mechanisms for
MIC on copper-based alloys [7]. CO2, H2S and NH3 accelerate localized attack. It has also
been shown [8] that Alloy 400 (UNS N04400) is highly susceptible to MIC in Arabian Gulf
seawater. Stainless steels, mainly the low alloyed 304 and 316 austenitic grades but also the
more highly alloyed grade 904L, suffer from MIC. Favorable conditions, in general, for it to
occur are stagnant conditions, organic nutrients in the water, sediment, absence or neglect of
chlorination practices as well as the presence of chlorides and sulphates.
Most troublesome for both copper-based alloys and stainless steel materials are sulphatereducing bacteria (SRB). The SRB are notorious for interfering with the formation of and
actually removing the protective surface oxide film. Severe localized pitting can occur on
iron-bearing 90Cu-10Ni if exposed even briefly to anaerobic seawater [9]. Some SRB use
hydrogen, depolarizing the cathodic surface and accelerating attack on a crevice site. SRB-
Seawater Corrosion
induced corrosion is often characterized by an encrusted deposit over a deep pit with a black
powdery sulphide corrosion product underneath.
At temperatures below approximately 35C, a biofilm present on a stainless steel surface
will raise the open circuit potential to +300-400 mV (SCE). At this temperature, the potential
increases the risk for localized attack on standard austenitic grades but not for a high alloyed
material such as UNS S32750. At temperatures above 40C, the micro-organisms in the
biofilm are no longer active resulting in a potential drop to essentially 0 mV (SCE) for the
stainless steel material. Since localized attacks such as pitting are dependent mainly
(excluding solution content) on potential and temperature the potential drop at higher
temperatures is advantageous. Thus at low temperatures, the open circuit potential is elevated
but not so much that it will initiate localized attack on UNS S32750, and at high temperatures
the potential is kept low so corrosion attack will for that reason not initiate. Tests carried out
at the Sandvik Steel R&D Centre have shown that UNS S32750 does not suffer from
corrosion attacks at 95C in natural seawater. There have not been any reports of MIC
attacks on UNS S32750 in operation.
Chlorination
In order to prevent the buildup of biofilm and to remove already attached biological
species, it is common practice to chlorinate the seawater by the addition of a hypochlorite
solution to the system. The usual objective is to keep residual chlorine levels below 0.5 ppm
at the inlet tube sheet, but this level sometimes is exceeded and the residue is normally
higher at the point of injection [1]. There is a marked difference in behavior between copperbased alloys and high alloyed stainless steel. Zanoni et al. [10] investigated the iron and
manganese alloyed copper-nickel alloy C71640 and its behavior in flowing natural seawater
with different chlorination levels. It was shown that 0.5 ppm free chlorine is the upper limit
for the material to maintain good resistance to localized corrosion.
With intermittent chlorination, which is used for economic and environmental reasons,
higher doses of chlorine are used but during limited time periods. A common time period for
chlorination is 2 x 15 minutes each day. The amount of chlorine added to the system varies,
but levels up to several parts per million are not uncommon for heat exchanger cooling
systems. This can make low alloyed stainless steels and copper-based alloys unsuitable for
these systems. Grade UNS S32750 can, however, maintain its resistance to corrosion even at
these high levels of chlorination.
When added continuously, the chlorination of seawater increases the corrosion potential
for the material to approximately +600 mV (SCE). At this high potential level, localized
corrosion attacks will initiate on UNS S32750 surfaces at 75-80C in stagnant conditions and
at approximately 10C above this at flow rates typical for seawater cooled heat exchanger
units. When adding chlorine intermittently, the open circuit potential will be lower than with
continuous chlorination but will vary with sharp potential peaks at the time of chlorine
addition.
EROSION-CORROSION
Seawater Corrosion
Stainless Steel
Including
UNS S32750
15
Brasses
120
Bronzes
70
Cu-Ni
Alloys
Glass
30-50
0.9
As can be seen from Table 3, UNS S32750 has a thermal conductivity 2-10 times lower
than all copper-based alloys. However, the heat transfer properties of tubular products cannot
be based exclusively on the thermal conductivity of the material itself. Other factors such as
the steam film, corrosion products, deposits and cooling water film must be considered.
Actually, the thermal conductivity of the tubular material in a heat exchanger has so little
influence on the overall heat transfer performance of the system that this term can be
neglected when calculating heat transfer rates. Table 4 illustrates the various factors affecting
resistance to heat transfer in actual service. It is obvious that surface films affect overall
performance to a far greater degree than the metal wall, which accounts for no more than 2%
of the total resistance to heat flow.
Table 4. Influence of Various Factors on the Heat Resistance of a Water-Cooled
Heat Exchanger [14]
Steam Side
Water Film
18%
Steam Side
Fouling
8%
Tube Wall
2%
Water Side
Fouling
33%
Water Side
Film
39%
Despite poorer thermal conductivity properties, UNS S32750 offers as good heat flow
properties as copper-based alloys do for seawater-cooled heat exchanger and condenser units.
GALVANIC CORROSION
Galvanic processes occur between different metals when they are coupled to each other
via a conductive media such as seawater. Current will flow with oxidation taking place at the
anode, and reduction (normally oxygen reduction) occurring at the cathode. If the two metals'
free corrosion potentials, Ecorr, differ by hundreds of millivolts from one another, the metal
with the more noble Ecorr value will become predominantly cathodic and the metal with the
more active Ecorr value will be the predominantly anodic one and will corrode. If the
difference is of the order of tens of millivolts, galvanic corrosion is less likely. In Table 5, the
corrosion potentials in natural seawater for some metals and alloys are given. The values shall
all be seen as approximate values, since the corrosion potentials differ with both flow rate and
temperature of the seawater.
Zn
Steel
Brasses
-1050
-600
-300
Cu-Ni
Alloys
-200
Ti
0
UNS
S32750
+50
Pt
+250
According to the text above and Table 5, galvanic corrosion is likely to occur copperbased tubulars are replaced with stainless steel or titanium tubing if the tube sheets are not
replaced at the same time. Investigations made on severely corroded, copper-based, alloy
tube sheets in connection with stainless steels and titanium have shown that the whole inside
of the noble alloy tubes becomes effective as a cathode in copper-based alloy coupled to
stainless or titanium [15].
Stainless steel or titanium tubing increases copper-based alloy tube sheet attack to a
point where impressed current cathodic protection normally is required to control tube sheet
corrosion. If titanium is to be used as replacement tubes, the cathodic protection unit must be
controlled to avoid hydriding of the tubes. The oxide film that normally covers the surface of
titanium has been shown to be an effective barrier to hydrogen penetration. In environments
where this film is unstable or where the oxide film has been damaged by abrasion, hydrogen
absorption can occur [16]. At potentials below approximately -700 mV (SCE), production of
hydrogen will occur and the risk for hydriding of titanium increases. If zinc is used as a
cathodic protection material, the potential will be significantly lower than this in seawater, 1000 mV (SCE), and hydrogen absorption is most likely to take place in the titanium tubulars.
The R&D Centre at AB Sandvik Steel has performed tests on UNS S32750 in connection
with zinc in solutions comparable to seawater at a potential of -1000 mV (SCE). The tests
were conducted at a temperature of 80C, and the results show that hydrogen embrittlement
will not harm the material in normal service situations. If pure iron is used instead of zinc as
a cathodic protection material the risk for hydrogen embrittlement will totally disappear for
UNS S32750. In contrast, it has been observed [16] that hydriding of titanium occurs most
frequently in solutions containing H2S where galvanic couples with iron exist. Thus, when
choosing UNS S32750 instead of titanium when replacing copper-based alloy tubulars in heat
exchangers, the problem with hydrogen absorption and embrittlement is reduced to a
minimum if the tube sheets are correctly cathodically protected.
STRESS CORROSION CRACKING
Low alloyed stainless steel grades, such as types 304 and 316, are prone to chlorideinduced SCC at temperatures above 50C which is one of the reasons why these materials
cannot be used in many of the seawater-cooled heat exchanger systems operating today.
Duplex grades do, however, possess very good resistance to stress corrosion due to their dual
microstructure and alloying contents. In seawater cooling systems for condensers and heat
exchangers, UNS S32750 can be considered as being immune to SCC, and no such case has
been reported. Neither has titanium suffered from SCC in seawater-cooled heat exchangers.
Copper-based alloys do not normally suffer from SCC in these applications, but brasses have
a clear tendency towards SCC in the presence of ammonia or ammonium salts [17].
Seawater Corrosion
LOCALIZED CORROSION
Stainless steels suffer from localized attacks, i.e., pitting and crevice corrosion, in
chloride-containing solutions such as seawater. Crevice sites are unlikely to occur if the
chlorination procedures are carried out correctly and a continuous flow is maintained inside
the tubes. Much of the sediment entrained in cooling water deposits out in the bottom of
condenser and heat exchanger tubing at velocities below about 1-1.5 m/s and during
shutdowns. Any unit designed or operated at lower velocities is a prime candidate for under
sediment crevice attack, MIC or both [15]. Therefore, it is of great importance to rinse the
inside of the tubes during shutdowns with freshwater, independent of material used for the
tubulars.
As for crevice attacks, the primary cause of pitting is the presence of chloride ions.
Often pitting attacks are initiated at defects at the surface like slag inclusions or chromiumrich precipitates around which a chromium depleted zone is present. Welds are very likely
the initiation sites for localized attacks because of their sometimes inhomogenous structure
and the presence of intermetallic precipitates in the melted or heat-affected zones adjacent to
the welds. Therefore, seamless tubes are preferred to welded ones.
Pitting is temperature-dependent, but will not occur in UNS S32750 in seawater at
normal potentials. However, chlorination of the seawater increases the open circuit potential
to approximately +600mV (SCE). At this high potential, pitting occurs very rapidly in low
alloyed stainless steels. For UNS S32750, the risk of pitting in seawater systems is very low,
provided the temperature is kept below 75-90C, depending on the flow rate of the cooling
water.
Tests performed at the R&D Centre at AB Sandvik Steel have shown that the critical
pitting temperature (CPT), i.e., the lowest temperature at which pitting initiates in a given
environment, increases with flow rate. The tests were performed in synthetic seawater with
the material being put to a potential of +600 mV (SCE). For stagnant conditions at this
potential, the CPT is 75-80C. For flow rates above 1.6 m/s, the lower flow rate limit for
most heat exchangers, it was shown in the tests performed at Sandvik that pitting would not
initiate at temperatures below 85C; CPTs at 90C and above were measured for flow rates at
2.2 m/s. According to Quik and Gedeuke [18], super duplex grades of the UNS S32750 type
can be used in unchlorinated seawater cooling systems up to 100C provided a constant flow
can be assured.
CASE HISTORY 1: SEAWATER CONTAINING H2S
In a condenser equipped with copper-nickel material (90Cu-10Ni tubes and 70Cu-30Ni
tube sheet), the tubes started leaking after less than four weeks in service. The seawater
contained H2S in an amount such that the environment became very corrosive to copper-based
alloys. As replacement tubing, the main candidate materials were UNS S32750 and titanium.
Due to the risk of hydriding of the titanium tubes because of hydrogen generation when
cathodically protected (to suppress the galvanic action between the titanium and the Cu-Ni
tube sheet) and vibration effects due to the lower rigidity of the thin-walled titanium tubes,
thereby causing risk of fatigue failure, UNS S32750 was chosen as the replacement material,
and the tubes were installed in October 1995.
Seawater Corrosion
If exclusively taking thermal conductivity levels of different materials into account, one
can conclude that UNS S32750 has approximately 2-10 times worse properties than copperbased alloys. As shown in this paper, however, the thermal conductivity of the tube material
contributes only 2% of the overall heat transfer of the system and can thus be neglected.
Seawater can, depending on its content and temperature, be corrosive to copper-based
alloys as well as to high alloyed stainless steels such as UNS S32750. In natural seawater
with no chlorine added, temperatures as high as 95C have been shown to not be high enough
to initiate corrosion attacks alone. When normal continuous chlorination procedures are used,
however, the open circuit potential rises to approximately +600 mV (SCE) for UNS S32750.
At this potential, the CPT for UNS S32750 is 75-80C for stagnant conditions and 10C
higher if a continuous flow above 1.5 m/s is maintained.
CONCLUSIONS
1. Copper-based alloys suffer from erosion-corrosion damage at flow rates occurring in
seawater-cooled heat exchangers. UNS S32750 does not suffer from erosion at fluid
velocities far above those likely to be maximum for heat exchanger applications.
2. Normal chlorination procedures, continuous or intermittent, will not initiate corrosion
of UNS S32750 as long as temperature and flow rate are kept within specified ranges.
3. Despite the lower thermal conductivity of UNS S32750 compared to copper-based
alloys, the overall heat transfer capacities of the different material systems are equal.
4. UNS S32750 does not suffer from pitting corrosion attacks at 95C in unchlorinated
seawater or at 75-80C in stagnant chlorinated solutions. With flow rates above 1.5
m/s, typical for heat exchanger systems, tests have shown the critical temperature
limit to be above 85C. These test results are good indications of the temperature
intervals within which UNS S32750 can be used.
5. With much better erosion and corrosion properties than copper-based alloys and with
properties at least as satisfactory as those of titanium and nickel-based alloys, UNS
S32750 must be considered to be one of the very best alternatives for seawater-cooled
heat exchangers in need of tube replacement.
REFERENCES
1.
2.
3.
4.
5.
6.
7.
8.
ABSTRACT
The susceptibility of aluminum-alloy 5083 and its weldments to stress corrosion cracking (SCC)
was investigated using constant strain and slow strain rate (SSR) tests in actual seawater, in the Bandar
Bushehr region, and in 3.5% NaCl solution, respectively. Also, electrochemical polarization and
immersion tests were performed to study the corrosion rate of the aluminum alloy and its weldments.
In addition, long-term tests, on actual sections of a marine vessel for a period of one year, were used to
investigate the corrosion behavior of alloy 5083 and its weldments in Bushehr seawater. Scanning
electron microscopy (SEM) was employed to characterize the nature of corrosion and SCC in the
specimens tested under various conditions.
The results indicated higher corrosion rates in 3.5% NaCl solution than in seawater. Also, the
corrosion rates of welded specimens were higher than those of unwelded specimens. In addition, the
results revealed no susceptibility to SCC of the alloy and its weldments in Bushehr seawater.
Key Words: Aluminum alloy 5083, stress corrosion cracking, weldments, Persian Gulf
INTRODUCTION
Aluminum alloy 5xxx series are non-heat-treatable alloys containing Mg and are widely
used for the construction of marine structures and vessels. On the other hand, during the
welding of these alloys, Mg2Al3 precipitates along the grain boundaries. Mg2Al3 is anodic
with respect to the base metal, and thus may render the alloy susceptible to stress corrosion
cracking (SCC). SCC often causes unexpected costly failures. This is due to a lack of visual
evidence of corrosion as compared with uniform and localized corrosion. SCC is a cracking
phenomenon under the conjoined action of tensile stress and corrosion, which happens for
some metals in specific environments. In other words, there are three main factors acting
together in SCC: tensile stress, which can be working or designed stress, or residual and
thermal stresses due to welding and other operations; the corrosion environment which is
affected by major and minor chemical composition, temperature, velocity or turbulence, and
even biological activities of the environment; and the susceptibility of the metal to SCC,
which can be affected by the chemical composition, microstructure, and thermal and
mechanical operations.
301
Seawater Corrosion
2+
Dissolved
solids (%)
Total Hardness
(ppm)
Ca
(ppm)
Mg
(ppm)
pH
6052
1335
7387
4.09
7.8
Dissolved
O2 (mg/l)
5.98
Salinity
(gm/l)
Cl
(%)
42.48
2.34
EXPERIMENTAL PROCEDURE
Specimens Preparation
The specimens for the various tests were cut from a 5 mm plate of the Al alloy 5083-O.
The chemical composition and mechanical properties of the alloy are shown in Tables 2 and
3, respectively. For weldments, the one-sided V-notch was used. Tungsten metal arc with
inert gas (TIG) and filler material 5183 were used for welding.
Table 2. Chemical Composition of Aluminium Alloy 5083-O (in wt.%)
Si
0.4
Fe
0.4
Cu
0.1
Mn
0.4-1.0
Mg
4.0-4.9
Cr
0.05-0.025
Zn
0.25
Ti
0.15
Al
balance
Saatchi et al.
Temper
O
Tensile Stress
(MPa)
290
Yield Stress
(MPa)
145
Elongation
(%)
22
Immersion Tests
Immersion tests were used to measure the corrosion rate of the base metal, with and
without welding, using the ASTM Gl standard. The specimens dimensions were 20 x 50 x 5
mm.
Polarization Tests
The cathodic and anodic polarization of the alloy and weld metals in actual seawater and
3.5% NaCl solution were determined by a potentiodynamic technique based on ASTM G587. The corrosion rates of the specimens were also calculated using the linear polarization
technique. The electrochemical measurements were performed using a standard potentiostat,
Wenking model ST72, with a Ag/AgCl reference electrode.
Figure 1. The details of specimens used for constant strain stress corrosion
tests
(a) unwelded; (b) cross weld; and (c) longitudinal weld
303
Seawater Corrosion
Figure 2. Part Nos. l and 2 simulating the most critical condition of a marine vessel
Slow Strain Rate (SSR) Tests
Figure 3 shows the details of the specimens which were used in SSR tests. For these
tests an SSR testing machine, based on the recommendations of Parkins [5], was designed and
-6 -1
constructed. The strain rate used was 3 x l0 s . This was based on the previous results
obtained [6,7]. Stress-strain curves for specimens without welding and welded in the gauge
304
Saatchi et al.
length area were obtained. These curves were plotted in various conditions including: air,
seawater and 3.5% NaCl solution. The fracture surfaces of the SSR specimens were studied
using SEM (JEOL model S6400).
Figure 3. Details of the specimens used in the SSR tests: (a) unwelded; and (b) welded
Intergranular Corrosion Tests
In order to determine the extent of precipitation of Mg2A13 and its effect on
intergranular corrosion, intergranular corrosion tests were performed on specimens with the
dimensions 50 x 6 x 5 mm in concentrated nitric acid based on ASTM G67-80. The weight
loss was measured.
RESULTS AND DISCUSSION
Figures 4 and 5 show the potentiodynamic polarization curves of the base metal and
weld metals in Bandar Bushehr seawater and in a 3.5% NaCl solution. All the data in these
curves are summarized in Table 4. The corrosion rates obtained for the base metal and weld
metal using the linear polarization technique and immersion tests are also summarized in
Table 4. In laboratory tests, specimens show a lower corrosion rate in seawater than in 3.5%
NaCl solution. This could be due to the lower salinity of the seawater compared to the 3.5%
NaCl solution. In all the test methods, welded specimens showed higher corrosion rates than
unwelded ones. This is due to the precipitation of anodic Mg2Al3 in grain boundaries in the
HAZ during welding. Table 3 shows that the corrosion rates obtained by electrochemical
methods were an order of magnitude higher than those obtained in either immersion tests in
the laboratory or in actual field conditions. This is obviously due to the fact that the duration
of the immersion tests in actual field conditions was long enough for hard marine fouling to
develop on the surface of the metal and thus protect it from further corrosion. Table 4 also
305
Seawater Corrosion
shows that the corrosion rates in actual field conditions were higher than the corrosion rates
in the laboratory immersion tests. This clearly indicates that the corrosion conditions in the
sea were more intense than in the laboratory situations.
Specimen
type
Environment
(mV)
-859
-2
0.105
-765
1.2 x 10
-2
0.066
-848
1.1 x 10
-2
0.095
-800
9.2 x 10
(mpy)
Unwelded
Seawater
2.4 x 10
Unwelded
3.5% NaCl
Solution
4.6 x 10
Welded
seawater
2.9 x 10
Welded
3.5% NaCl
Solution
4.4 x 10
Immersion
Tests in
Laboratory
Corrosion Rate
(mpy)
-2
8.4 x 10
-4
-3
-3
-4
Immersion Tests in
Bandar Bushehr
corrosion Rate
(mpy)
1 x 10
-3
--
1.54 x 10
-3
--
Figure 6 shows typical constant strain rate specimens and Part Nos. l and 2 that were
immersed at various depths below the waters surface in Bandar Bushehr region for 12
months before cleaning. Severe hard fouling can be seen. After cleaning the specimens, they
were inspected for cracks. No cracking was observed in either of the specimens. These
results, summarized in Table 5, indicate that neither the base metal, nor the welded specimens
show any cracking under stress after 12 months of exposure to Bandar Bushehr seawater.
306
Saatchi et al.
Figure 6. Constant strain test specimen and Part Nos. 1 and 2 before cleaning exposed in
Bandar Bushehr seawater for 12 months
Table 5. Results of Constant Strain Tests and Simulated Service Condition Tests in Bandar
Bushehr Seawater for 12 months
307
Seawater Corrosion
Specimen Type
Unwelded
Transverse weld
Longitudinal weld
Unwelded
Transverse weld
Longitudinal weld
Part No. 1
Part No. 2
Depth (m)
Splash zone
Splash zone
5
5
5
5
5
5
Results
No cracks
No cracks
No cracks
No cracks
No cracks
No cracks
No cracks
No cracks
Figures 7 and 8 show the typical stress strain curves for the aluminum alloy 5083 with
and without welding obtained by the SSR testing machine. The specimens were tested in air,
as well as in seawater and 3.5% NaCl solution. The results obtained from these tests are
summarized in Table 6. There is no indication of SCC susceptibility from these test results.
Figure 9 shows a typical SEM fractograph of the fractured surface of the SSR test
specimens. All the fractured surfaces showed dimple fracture and no indication of
susceptibility to SCC in the environments tested.
Table 7 summarizes the intergranular test results in nitric acid, according to ASTM G6780. The data shows that the average weight loss of the unwelded specimens was 2.46
mg/cm2, and that of the welded specimens was 3.54 mg/cm2. These rates are below the range
of integranular susceptibility according to the ASTM standard.
308
Saatchi et al.
Specimen
Environment
Unwelded
Welded
Unwelded
Welded
Unwelded
Welded
Air
Air
Seawater
Seawater
3.5% NaCl solution
3.5% NaCl solution
Failure Time
(h)
24.40
17
24.30
21.16
26
20.43
Max Load
(N)
1900
1100
1600
1802
1540
1610
Failure Load
(N)
1490
1050
1380
1690
1320
1600
Failure Stress
2
(N/mm )
99.3
70
92
113
88
106.6
Figure 9. Typical SEM fractograph of the fractured surface of an SSR test specimen in
seawater: (a) unwelded; and (b) welded
Table 7. Intergranular Test Results on Welded and Unwelded Aluminum Alloy 5083
Specimen
Area
(mm )
1333
Initial
Weight
(gr)
4.0915
Final
Weight
(gr)
4.0515
Weight
Loss
(gr)
0.04
Weight
Loss
2
(gr/cm )
3
1227
3.8998
3.8765
0.0233
1.91
2.46
1552
1025
6.2633
2.8906
6.2028
2.8581
0.0605
0.0325
3.9
3.17
3.54
Unwelde
d
Unwelde
d
Welded
Welded
Average
Rating
(mg/cm )
acceptable
acceptable
309
Seawater Corrosion
CONCLUSIONS
1. Constant strain specimens and also simulated marine vessel parts made from aluminum
alloy 5083 with and without welding, immersed in Persian Gulf seawater at various
depths for 12 months did not show any cracking tendency.
2. SSR test results and SEM fractographs of the fractured surfaces did not show any
indication of SCC susceptibility of this alloy with or without welding.
3. Welding aluminum alloy 5083 with TIG, increased the corrosion rate, due to grain
boundary precipitation, but the intergranular corrosion rate remained in the acceptable
range.
REFERENCES
1. G.A. Gehring, Materials Performance 9, 1987, p. 9.
2. G. Sandoz, Stress Corrosion Cracking in High Strength Steels and in Titanium and
Aluminum alloys, B.F. Brown, ed., Naval Research Laboratory, 1972.
3. G. Sandoz, Metallurgical Transactions 2, 1971, p. 1055.
4. H.P.Lockie and A.W. Loginow, Corrosion 14, 1968, p. 291.
5. R.N. Parkins, ASTM STP 665, 1987, pp. 2-25.
6. M. Sobhani, M.Sc. Theses, Materials Engineering Department, Isfahan University of
Technology, 1990.
7. R. Mozafarinia, M.Sc. Theses, Materials Engineering Department, Isfahan University of
Technology, Iran, 1994.
310
ABSTRACT
This paper summarizes the results of extensive laboratory research carried out on the cavitation
corrosion behavior of three cast alloys in seawater. The alloys studied were nodular cast iron (NCI),
nickel-aluminum bronze (NAB) and duplex stainless steel (DSS). The work included measurements
of free corrosion potential, potentiodynamic polarization and mass loss in presence and absence of
cavitation. The cavitation tests were made using an ultrasonically induced cavitation facility at a
frequency of 20 kHz. Cavitation caused an active shift in the free corrosion potential and increased
the anodic polarization current for the three cast alloys. In quiescent seawater, the rates of mass loss
were very low for all of the alloys studied. Cavitation increased the rates of NCI, NAB and DSS by
930, 186 and 20 times, respectively. However, the application of cathodic protection decreased the
rates of NCI, NAB and DSS by about 50%, 47% and 19%, respectively. Morphological examinations
revealed that thin scales were formed on NCI in quiescent seawater, while NAB suffered from
selective corrosion of the copper-rich phase. On the other hand, DSS was almost free of corrosion
in quiescent seawater. Cavitation made the surfaces of the alloys very rough, exhibiting large size
cavities and ductile tearing. The cavitation damage started at the graphite nodules and ferrite matrix in
NCI, the boundaries of columnar grains in NAB, and the ferrite/austenite boundaries and the
austenite islands in DSS. Cross-sectional examinations revealed microcracks in the bulk of the alloys.
The formation of microcracks was attributed to cavitation stresses and preferential phase corrosion.
Key Words:
INTRODUCTION
During the last few years, extensive research was made in our laboratory in the
investigation of the flow-dependent corrosion behavior of cast alloys used in the
manufacturing of seawater valves and pumps. This research was due to the repeated failures
of such components in the seawater systems of the petroleum refineries in Kuwait. Failure
analysis [1-3] revealed that the damage was due to a combination of several factors that
included cavitation corrosion, erosion-corrosion and preferential phase corrosion. This paper
summarizes the results of laboratory cavitation studies made on nodular cast iron (NCI),
nickel-aluminum bronze (NAB) and duplex stainless steel (DSS). The work was aimed at (1)
determining the relative susceptibility of the three cast alloys to cavitation damage; (2)
311
Seawater Corrosion
determining the effect of the application of cathodic protection in minimizing the degree of
damage; and (3) characterizing the role played by the different phases of the alloys during
cavitation.
Cavitation may be defined as the growth and collapse of vapor bubbles due to localized
pressure changes in a liquid. The collapse process takes place extremely rapidly, producing
strong shock waves that damage the material. Because a few million bubbles may collapse in
a second, damage quickly occurs. Published work [4,5] has shown that both mechanical and
electrochemical factors are involved in cavitation. Many investigators [4-7] have indicated
that cavitation can be reduced by applying cathodic protection to the cavitating body.
EXPERIMENTAL PROCEDURE
A study was made on specimens machined from the base of a failed NCI valve, the upper
casing of a failed NAB pump, and commercially cast DSS. Table 1 shows the chemical
composition of the alloys studied.
Table 1. Chemical Composition of Cast Alloys Used in the Cavitation Studies
Element (%)
Cast Alloy
NCI
NAB
DSS
C
3.54
0.04
Si
2.26
0.57
Mn
0.40
1.20
0.54
P
0.05
-
Cr
24.40
Ni
4.90
5.60
Mo
2.50
Cu
80.00
-
Al
9.00
-
N2
0.12
Fe
Bal
4.90
Bal
312
Al-Hashem et al.
The study was made in untreated seawater collected from the Arabian Gulf. This
seawater is very saline (46,000 TDS), and it has a pH of about 8.0. The composition of this
seawater has been previously reported [10].
The cavitation tests were carried out at a frequency of 20 kHz and an amplitude of 25 m
using an ultrasonically induced cavitation facility. The facility consists of a generator, a
converter, and a disrupter horn. The test specimens were mounted on a special holder which
was placed at a distance of 0.125 cm from the apparatus horn. The specimens area facing the
horn, and thus exposed to cavitation, was 1 cm2. The seawater was contained in an open
600-ml Pyrex beaker surrounded by a copper cooling coil in a water bath. The seawater
electrolyte was maintained at 25 + 1oC by controlling the flow rate and the temperature of the
circulating chilled water. The cavitation tests were made under free corrosion and cathodic
protection (CP) conditions. In the later tests, the specimens were kept at a single potential
value more negative than the free corrosion potential by 50 mV for NCI and NAB and 100
mV for DSS. The specimens were weighed after different time intervals in order to determine
the rate of mass loss as a function of cavitation time. In order to compare the rate of mass
loss in the presence of cavitation with that obtained in its absence, the rate of mass loss was
also determined for specimens immersed in quiescent seawater under free corrosion
conditions.
In order to evaluate the role of cavitation on the electrochemical behavior of the
materials, open-circuit potential and potentiodynamic polarization measurements were made
under quiescent and cavitation conditions. The polarization tests were carried out using
standard equipment at a scan rate of 0.5 mVs-1 starting from a potential value more negative
than the open-circuit potential. A saturated calomel reference electrode (SCE) and a graphite
counter electrode were used in these experiments.
To follow up on the development of cavitation damage and to identify the susceptibility
of the constituent phases to cavitation, detailed morphological examinations were made on all
tested specimens using scanning electron microscopy (SEM).
RESULTS AND DISCUSSION
Effect of Cavitation on Rates of Mass Loss
The rates of mass loss under quiescent conditions were very small for all alloys. In the
presence of cavitation, the mass loss behavior was quite similar for the three cast alloys. In
all cases, the rate of mass loss initially increased till it reached a maximum. Then, it sharply
decreased with the increase of cavitation time, followed by a slow decrease till a steady-state
was reached. This behavior remained unchanged in the presence of CP. However, the rates
of mass loss of specimens cavitated under free corrosion conditions were substantially higher
than those obtained in presence of CP. Figure 1 is given as an example to show the rates of
mass loss obtained for NAB and DSS, while Table 2 gives a summary of the rates of mass
loss at the steady-state for the three cast alloys after various test conditions.
313
Seawater Corrosion
(a)
(b)
Figure 1. Rates of mass loss of: (a) NAB; and (b) DSS specimens, exposed
to seawater under various conditions.
Table 2. Rates of Mass Loss (in mg.hr-1.cm-2) for Cast Alloys Exposed
to Seawater Under Various Test Conditions
Test Condition
Cavitation under free corrosion
Cavitation under CP
Quiescent
NCI: Nodular cast iron
NAB: Nickel-aluminum bronze
DSS: Duplex stainless steel
NCI
3.12
1.56
3.36 x 10-3
NAB
1.50
0.80
8 x 10-3
DSS
0.64
0.52
2.5 x 10-4
It is clear from Table 2 that the rates of mass loss of the cavitated specimens under CP
were lower than those under free corrosion conditions by about 50% for NCI, 47% for NAB
and 19% for DSS. This difference should be equivalent to the electrochemical corrosion rates
of the alloys. A comparison of the mass loss rates obtained under quiescent conditions with
those obtained under cavitation conditions indicates that the kinetics of electrode process are
314
Al-Hashem et al.
enhanced by cavitation. In other words, the greatest portion of damage during cavitation is
due to mechanical breakdown of the material surface and subsequent particle separation and
ejection from the metal. However, the results clearly show that DSS is quite resistant to
electrochemical corrosion in seawater. Thus, although cavitation has exposed fresh metal
surfaces to the aggressive environment, the enhancement of electrochemical corrosion in DSS
was not as significant as in NCI or NAB.
In the present study, CP was applied to the cavitated specimens in order to separate the
electrochemical corrosion component from the mechanical one. The present results indicate
that the application of CP during cavitation reduces the rates of mass loss for all the
investigated alloys. Since the rates of mass loss in quiescent seawater were very low, this
decrease cannot be solely attributed to the elimination of electrochemical dissolution. Thus,
the reduction in the rate of mass loss during cavitation under CP could be due to a
combination of two factors, namely: bubble collapse cushioning due to the development of
cathodic gas and diminished electrochemical dissolution [6].
Effect of Cavitation on the Electrochemical Behavior of Cast Alloys
The potentials of NCI and NAB specimens exposed to seawater under cavitation and
quiescent conditions were measured as a function of time. Table 3 shows the initial potential
values obtained upon immersion and the final potentials at steady-state.
Table 3. Corrosion Potentials (in mV vs. SCE) of Cast Alloys Exposed to
Seawater under Quiescent and Cavitation Conditions
Alloy
Quiescent
Initial Values At Steady-state
NCI
-560
-740
NAB
-260
-245
NCI: Nodular cast iron
NAB: Nickel-aluminum bronze
Cavitation
Initial Values
At Steady-state
-560
-650
-325
-300
It is clear from Table 3 that cavitation causes an active shift in the corrosion potential of
NCI and a noble shift in the case of NAB. However, it is worth noting that the application of
cavitation causes an immediate active shift in the initial corrosion potential of NAB. In order
to validate this effect, the measurements were repeated on NAB and DSS under a pulsating
cavitation condition. In these experiments, the materials were alternatively exposed to
periods of cavitation and quiescence for one hour each. Figure 2 is given as an example to
show that the application of cavitation immediately shifted the potential to a more active
value. When cavitation was stopped, the potential rapidly shifted back to that of the quiescent
condition. The rapid activation of the corrosion potential can be explained in terms of the
destruction of the passive film and the creation of fresh metal surfaces. On the other hand,
the rapid reversal of the free corrosion potential when cavitation was stopped suggests that
the repassivation kinetics is quite fast. A similar potential shift was previously reported for
copper-manganese-aluminum alloys cavitated in seawater [11].
315
Seawater Corrosion
(a)
316
(b)
Al-Hashem et al.
Figure 3. Potentiodynamic polarization curves for: (a) NAB; and (b) and DSS,
immersed in seawater under quiescent and cavitation conditions
Effect of Cavitation on Surface Damage
In stagnant seawater, a loosely adherent, corrosion product layer was formed on NCI.
After cavitation for 2-10 minutes, erosion markings were visually observed. When SEM
examinations were made, the NCI surface was found to have suffered from localized surface
damage, as early as after 1 minute of cavitation. The damage was in the form of
fragmentation and removal of graphite nodules. This led to the formation of circular craters
of cavities; while the surrounding matrix remained smooth and unattacked (Fig. 4a). After 5
min., microcavities (erosion pits) developed in the ferrite matrix along with other cavities
caused by the loss of graphite. After 10 to 30 minutes, the attacked areas became larger and
engulfed the microcavities. Longer cavitation testing (5.5 hours) showed ductile removal of
material from the matrix (Fig. 4b). These characteristics did not change in the presence of
CP. However, the time needed to reach a specific stage of damage was longer under CP.
Examinations of cross-sections revealed cracks, 3-21m long, that propagated into the matrix.
These cracks originated at the bottom of deep craters.
In general, cavitation corrosion increases in corrosive liquids such as seawater due to the
combined action of electrochemical corrosion and the fluid mechanical component. Arabian
Gulf seawater seems to be more aggressive than other water bodies, as it contains higher salt
and different pollutants [10]. In the present work, erosion pits appeared randomly in the
ferrite matrix of NCI due to ductile tearing caused by the sudden collapse of liquid bubbles.
This indicates that cavitation damage in cast iron is not only initiated at graphite nodules as
mentioned by Okada et al. [13], but also in the ferrite matrix.
(a)
(b)
317
Seawater Corrosion
Figure 4. SEM micrographs of NCI after cavitation testing in seawater. (a) after 1
minute, fragmented graphite nodules and formation of cavities; and (b)
after 5.5 hours, ductile removal of material from ferrite matrix
The surface of NAB specimens exposed to stagnant seawater appeared visually darker
than the unexposed specimens. SEM examinations indicated that the phase was
preferentially attacked at the /IV interfaces and the precipitate-free zone did not suffer
from any attack (Fig. 5a). Dissolution of the phase was also noted around the dendritic
(rosette-like) II precipitates and at the globular and lamellar III precipitates. The fact that
the precipitates were not attacked, indicates that the precipitates are cathodic with respect
to the copper-rich phase. Thus, corrosion of NAB alloy in quiescent seawater is galvanic in
nature.
SEM examinations revealed that the surface of the NAB specimen became slightly rough
after 3 hours of cavitation. After 13 hours of cavitation, the surface roughness increased and
several microcavities appeared in the attacked area (Fig. 5b). As the cavitation time increased
to 25 and 40 hours, the surface became very rough and contained large size cavities.
Cleaning the specimen that had been cavitated for 40 hours in acetone revealed ductile tearing
and grain boundary attack. In the presence of CP, the number of microcavities increased, but
grain boundary attack was absent. Examination of a cross-section of a specimen cavitated for
58 hours revealed microcracks, 5-10 m in length, emanating from the bottoms of cavities
(Fig. 5c). The microcracks appeared to initiate and propagate in the phase, favoring sites
adjacent to phases.
(a)
318
(b)
Al-Hashem et al.
(c)
Figure 5. SEM micrographs of NAB after: (a) exposure to quiescent seawater for
48 hours, showing preferential attack of the phase; (b) cavitation
testing for 13 hr, showing increased surface roughness; and (c)
cavitation testing for 58 hr, showing cavities and microcracks in crosssection
The presence of cavities and ductile tearing in cavitated NAB specimens is readily
explainable in terms of the known devastating effects of cavitation. On the other hand, the
presence of grain boundary attack indicates that electrochemical dissolution due to structural
heterogeneity indeed contributes to the surface damage. The presence of microcracks in the
bulk of the material is similar to that reported for the NAB vertical-type pumps and sleeve
valves that prematurely failed in Arabian Gulf seawater [1,2]. Although selective phase
corrosion may have played a role in causing the microcracks, the contribution of cavitation
stresses should not be discounted.
The DSS specimens exposed to quiescent seawater under free corrosion conditions were
found to be free of any corrosion attack. When SEM examinations were made on the DSS
cavitated in seawater under free corrosion conditions, damage was seen after 30 minutes of
cavitation. At this stage, a few small, shallow voids were seen inside the austenite islands
and at the phase boundaries. Slip lines were also observed in the ferrite matrix with
microvoids developing at emerging slip steps. Furthermore, some austenite islands partially
extruded and experienced metal loss (Fig. 6a).
(a)
(b)
Figure 6. SEM micrographs of DSS after cavitation testing in seawater. (a) after 30
minutes, void formation at emerging slip steps and partially extruded
austenite; and (b) after 90 minutes, total removal of an extruded
austenite and extension of damage to ferrite
319
Seawater Corrosion
After 70 minutes of cavitation, the formation of voids along the slip steps and the
material removal from the extruded austenite became more extensive. Slip lines were also
seen within the ferrite matrix and cleavage-like facets within the damaged austenite. After 90
minutes of cavitation, the extruded austenite was totally removed and the loss in material
extended to the ferrite matrix (Fig. 6b). As the cavitation time was increased to 4 hours, the
whole metal surface suffered from extensive damage and the formation of cavities. At this
stage, ductile tearing, cleavage-like facets, river patterns and crystallographic steps were seen
on the damaged surface. When the examinations were repeated on a specimen cavitated for
40 hours under CP, the surface roughness appeared to be somewhat less than under free
corrosion conditions. Laboratory-etched cross-sections of specimens cavitated for 40 hours
revealed microcracks in the bulk of the alloy. The cracks appeared to initiate in the ferrite
matrix. The propagation of the cracks appeared to be impeded by the austenite islands and to
branch along parallel slip systems. In some cases, however, cracks were seen extending into
the austenite grains.
The high ductility of the austenite could explain the extrusion of surface austenite. The
presence of cleavage facets within the damaged austenite suggests the occurrence of a brittle
mode of failure in addition to the ductile mode. This was rather surprising. The brittle mode
of failure in the austenite may be due to a strain-induced martensitic transformation [14].
The localized nature of cavitation seems to have led to an increase in work hardening of
the ferrite matrix, activation of slip systems and initiation of surface cracks. Thus, the earliest
deformation caused by the slip is expected to occur on the {110} plane and in the [111]
direction. The localization of plastic strain would also facilitate material removal by ductile
shearing of surface asperities. The repetitive stress mode of cavitation causes the cracks to
propagate laterally, giving rise to the observed cleavage-like facets. The cracks in the bulk of
the material express the fact that the plastic shock waves produced by cavitation can travel
deep into the material. The role of the austenite islands in impeding crack propagation has
been previously reported in stress corrosion cracking [6] and hydrogen embrittlement studies
[15]. It is feasible that passage of the propagating crack through an austenite obstacle is
facilitated by the formation of -martensite.
CONCLUSIONS
1. Cavitation caused an active shift in the free corrosion potential and increased the
anodic polarization current of NCI, NAB and DSS.
2. The rates of mass loss of the three cast alloys were very low in quiescent seawater.
When compared with quiescent conditions, cavitation increased the rates of mass loss
at the steady state by 930, 186 and 20 times for NCI, NAB and DSS, respectively.
The application of CP decreased the rates of mass loss by about 50%, 47% and 19%,
respectively. This reduction was attributed to bubble collapse cushioning due to
cathodic gas and diminished electrochemical dissolution.
3. In quiescent seawater, thin scales were formed on NCI, while NAB suffered from
selective corrosion of the copper-rich phase at the interfaces with the intermetallic
precipitates. DSS was almost free of corrosion.
320
Al-Hashem et al.
4. Cavitation made the surfaces of the alloys very rough, with large size cavities and
ductile tearing. The damage started at the graphite nodules and ferrite matrix in NCI.
In NAB, the damage started at the boundaries of columnar grains. In the case of
DSS, slip lines formed in the ferrite matrix, austenite islands extruded, and voids
developed at emerging slip steps. Cleavage facets were evident within the damaged
austenite. The extrusion of the austenite was attributed to its high ductility, while the
presence of cleavage facets was explained in terms of strain-induced martensite.
Cross-sectional examinations revealed microcracks in the bulk of the cast alloys. The
formation of microcracks was attributed to cavitation stresses and preferential phase
corrosion.
ACKNOWLEDGMENT
The authors of this paper would like to acknowledge the support given by the Kuwait
Foundation for the Advancement of Science, the Kuwait National Petroleum Company, the
Petrochemical Industries Company, and the Abu Dhabi National Oil Company (Project No.
86-08-02).
REFERENCES
1.
2.
3.
4.
H.M. Shalaby and J.K. Cheriyan, KISR Report No. 2799, September 1988.
M. Islam, R. Abdul Wahab and S. Al-Kharraz, KISR Report No. 2913, January 1989.
V.K. Gouda, H.M. Shalaby and W.T. Riad, Materials Performance 28, 8, 1989, p. 53.
H.M. Shalaby, A. Al-Hashem, H. Al-Mazeedi and A. Abdullah, British Corrosion
Journal 30, 1, 1995, p. 63.
5. J.G. Auret, O.F.R.A. Damm, G.J. Wright and F.P.A. Robinson, Corrosion 49, 11,
1993, p. 910.
6. C.M. Preece, Cavitation erosion, in Treatise on Material Science and Technology,
Vol. 16, C. C.M. Preece, ed. (New York, NY: Academic Press, 1979), p. 249.
7. A. Al-Hashem, P.G. Caceres, W.T. Riad and H.M. Shalaby, Corrosion 51, 5, 1995, p.
331.
8. F. Hasan, J. Iqbal and N Ridley, Materials Science Technology 1, 1985, p. 312.
9. ASTM G32-92, Standard Test Method for Cavitation Erosion Using Vibratory
Apparatus (Philadelphia, Pennsylvania: ASTM, 1992).
10. H.M. Shalaby, S. Attari, W.T. Riad and V.K. Gouda, Corrosion 48, 3, 1992, p. 206.
11. K.R. Trethewey, T.J. Haley and C.C. Clark, British Corrosion Journal 23, 1, 1988, p.
55.
12. A. Schussler and H.E. Exner, Corrosion Science 34, 11, 1993, p. 1803.
13. T. Okada, Y. Iwai and A. Yamamoto, Wear 84, 1983, p. 297.
14. J.A. Venables, Philosophical Magazine 7 1962, p. 35.
15. W. Zheng and D. Hardie, Corrosion 47, 10, 1991, p. 792.
321
ABSTRACT
Microbiologically induced corrosion (MIC) is recognized as a major cause of metallic
component failure in many natural waters and soils. Most recently, a MIC failure occurred in the
stainless steel piping system in a chemical plant in Saudi Arabia. This failure case was discussed and
compared with the documented case histories in the published literature involving MIC of stainless
steels.
Key Words: Microbiologically induced corrosion (MIC), stainless steel, localized corrosion
INTRODUCTION
In late July of 1995, leakage was detected in the newly installed stainless steel (Grade
321 stainless) pipe in a chemical plant in Saudi Arabia. The leakage was observed in the
stainless steel core pipe which was enveloped by an outer jacket pipe for heat transfer
medium oil. Evidence of pinholes was found in the lowest sloping, horizontal section of the
core pipe, always around the 7 o'clock to 5 o'clock positions and about 0-8 mm from the weld.
The remainder of the pipes at a higher elevation have been found to be acceptable with no
leakage.
The original hydrotest using untreated fresh water was conducted for the newly
constructed pipe line in January of 1995, followed by air blowing to remove excess water.
This line was turned to the operating personnel of the chemical plant in March of 1995.
System hydrostatic leak testing was conducted by the plant personnel in April of 1995.
Pinhole leakage was observed in late July of 1995. Between April of 1995 and the leakage
was detection, the pipeline was never in use. In August of 1995, an investigation was initiated
on the cause of this failure. The investigation and analysis results are reported in this paper.
VISUAL AND MICRO EXAMINATION
One small pipe sample about 4 cm in length was cut from the failed stainless steel
pipeline for examination and evaluation. The sample included the weldment and pinholes.
This sample was cut along the longitudinal direction to expose the inner pipe surface for
examination. The measured outside diameter (OD) of the stainless steel pipe sample in asreceived condition was 88 mm with 3 mm in wall thickness. There was no observed
corrosion on the outer surface, as shown in the photograph in Fig. 1a. However, there were
reddish-brown corrosion products mixed with some light black oxides at and near the welded
323
Seawater Corrosion
zone of the inner surface, especially at the 5 to 7 o'clock position. One pit is clearly visible at
approximately the 6 o'clock position adjacent to the weldment, as shown in the photograph in
Fig. 1b. The area including the pit was cut for further examination under scanning electron
microscope (SEM). Figure 2a is a SEM photograph of the pit clearly indicating that the pit
was initiated from the inner surface at area near the weldment. Figure 2b is a SEM
photograph of the front view of
(a)
(b)
324
Lee et al.
Figure 1. Photographs of: (a) outer surface; (b) inner surface of the failed pipe sample,
indicating a pit growing nd propagating sideways from the inner surface adjacent to
the weldment
the pit indicating that the pit was turning sideways under the inner pipe surface. Figure 3 is a
SEM photograph of the side view of the pit looking from the cross-sectional direction of the
pipe showing a large under-surface cavity. This pit under examination did not penetrate the
whole pipe wall thickness. It clearly indicates that the pit was generated due to corrosion and
not from material defect.
ANALYSIS OF THE FAILURE MECHANISM
Based on the laboratory examination result, there are two possible environments which
could produce the type of pitting corrosion of stainless steel pipe as observed in the present
case. These include environment containing appreciable concentrations of chloride (Cl-), and
environment containing bacteria which could microbiologically induce corrosion of stainless
steels. These possibilities are further discussed in reference to the present failure case:
Pitting Corrosion of Stainless Steel in Environment Containing Chloride
It is known that stainless steel will develop pitting corrosion in environments containing
chloride ions because of the breakdown of surface passivity [1]. Generally, this requires an
appreciable concentration of chloride ions. For examples, stainless steels exposed to seawater
will develop surface pits in a matter of months to several years depending on the steels
composition. The tendency is greater in the martensitic and ferritic stainless steels than in the
austenitic steels. Austenitic stainless steels containing molybdenum (such as types 316 and
317) are more resistant to pitting corrosion in seawater. Pitting of these alloys will develop in
seawater within a period of 1-2.5 years [1]. The present failed stainless steel pipe was never
exposed to an aqueous environment containing appreciable amount of chloride ions prior to
the detection of the leakage. The type of pitting corrosion observed at this chemical plant is
not caused by chloride ions from the environment.
Localized Biological Corrosion of Stainless Steels
Biological corrosion is defined as the deterioration of metals as a result of the metabolic
activities of microorganisms [2]. Many case histories involving MIC of stainless steels are
well documented in the published literature [2]. Most of them involved sulfate-reducing
bacteria which accelerate the localized corrosion of stainless steels especially at welded areas.
One case history, as cited by Kobrin [3], is considered most relevant. It occurred in the early
1980s in a new chemical plant in Texas, USA.
Type 304 stainless was used for resistance to corrosion by wet carbon dioxide.
Included were underground sump tanks and drainage piping. Untreated well water
was used for hydrostatic testing after installation. No special effort was made to
remove the water or dry the systems after testing was complete. Initial indication of
a problem occurred several months after the hydrotest, following removal of a tank
to a fabrication shop for minor modifications. Leaks developed during a routine
shop hydrostatic test. Internal visual and liquid dye penetrant inspection showed pits
and cracks under rusting colored nodular deposits primarily along welds. Pits had
small 'mouth' at the surface, opening to large, bottle-shaped cavities below. As plant
personnel opened the stainless vessels and the pipes for inspection, they found many
325
Seawater Corrosion
pits, primarily at welds, and noted rust-colored deposits in mixture with brownishwhite slime deposits. Limited analyses showed the presence of sulfate reducing and
iron bacteria in the various deposits [4].
(a)
(b)
326
Lee et al.
Figure 2. SEM photographs of: (a) the pit adjacent to the weldment (7X); and (b) the pit as
seen from the inner pipes surface (25X)
Figure 3. SEM photograph of the pit hole from the cross-sectional direction indicating the pit
growing sideways under the surface (25X)
The above reported case history is very similar to what has been observed at the
chemical plant in Saudi Arabia for the present pipeline pitting failure. It appears that some
water still remained in the lowest sloping horizontal section of the core pipe at the chemical
plant after the initial hydrotest conducted in January of 1995. Obviously the untreated water
used for the initial hydrotesting contained some sulfate reducing bacteria which caused the
subsequent biologically induced corrosion.
As showed in the SEM photograph in Fig. 3, some rod-shaped material is visible inside
the pit. It is possible that the rod-shaped material could be a colony of the corroding bacterial
consortium. According to the literature, there are many bacteria found in the corroded metals
in the form of filaments. One example is the filament-form thermophillic bacterium found in
the failed brazed fillet reported by Walch and Mitchell [5]. This filament form of organism
has variable lengths from 20 to over 200 m.
Although Sabic R&D does not have the facilities to positively identify the type of
organism observed, it is fairly clear that the present pipeline failure observed at the chemical
plant was caused by biologically induced corrosion. Furthermore, the shape of the pit, i.e.,
with a small mouth on the surface and a large bottle-shaped cavity below, is a positive
indication of bacterial corrosion.
CONCLUSIONS
327
Seawater Corrosion
Based on the examination results and the evidence obtained, the cause of the pitting
corrosion in the stainless steel piping system observed was caused by biologically induced
corrosion. After the piping system was repaired or replaced as required, it was recommended
that hydrotesting be conducted using demineralized water to eliminate the possibility of
microbiologically induced corrosion. The piping system was thoroughly drained and dried
immediately after testing. There was no reoccurrence of MIC since.
REFERENCES
1. H.H. Uhlig and R.W. Revie, Corrosion and Corrosion Control, John Wiley & Sons, 1985.
2. Metals Handbook, Ninth Edition, Vol. 13, Corrosion, p. 2, ASM International, 1987.
3. G. Kobrin, Reflections on microbiologically induced corrosion of stainless steels, in:
Biologically Induced Corrosion, Conference Proceedings, National Association of
Corrosion Engineers, 1986, pp. 33-46.
4. ibid., p. 37.
5. M. Walch and R. Mitchell, Microbial influence on hydrogen uptake by metals, in:
Biologically Induced Corrosion, Conference Proceedings, National Association of
Corrosion Engineers, 1986, pp. 201-214.
328
ABSTRACT
Failure analysis and a laboratory study were made on Al-brass tubes. The failure investigation
was conducted on tubes that had failed during service in Arabian Gulf seawater. The investigation
revealed that the tubes failed due to perforations after suffering from various forms of corrosion.
Crevice attack and erosion-corrosion of the horseshoe grooving type were the most serious corrosion
forms. Other corrosion forms were also observed such as inlet edge cutting, inlet edge beveling,
pitting, dezincification and intergranular attack. Lodgments, local high velocities and turbulence were
considered the most important factors causing the perforations.
In order to understand the role played by the presence of seawater pollutants, a systematic
laboratory study was conducted to evaluate the effects of manganese (5 ppm) and chlorine (4 ppm) on
the corrosion behavior of Al-brass in stagnant and flowing (0.1 and 2.2 m/s) seawater. Under stagnant
conditions, both pollutants had little effect on the free corrosion potential. In flowing seawater,
manganese caused a noble shift in the corrosion potential at 0.1 m/s and an active shift at 2.2 m/s.
Chlorine addition caused an electropositive shift at both flow velocities. During polarization, the
presence of either pollutant caused cathodic depolarization and elimination of the active/passive
transition. Microscopic examination revealed that the film formed in the presence of manganese was
thicker and more porous than that formed in clean seawater. Scattered nodules of basic copper
chlorides formed on the tubes surface in the presence of chlorine. As in the field failed tubes, crevice
corrosion, intergranular attack and dealloying were found beneath the basic chloride nodules.
Key Words: Aluminum brass, corrosion failure, manganese, chlorine, pollutants
INTRODUCTION
In Kuwait, refineries and desalination plants utilize Arabian Gulf seawater in heat
exchangers, evaporators and condensers fitted with Al-brass tubes. Although the alloy is
recommended for the heat recovery stages in multistage flash distillation (MSF) plants [1], a
high incidence of tube failures have been reported [2-6].
The diagnosis of failure of Al-brass tubes in surface condensers, conducted by Gouda et
al. [4], indicated that the tubes failed due to severe erosion-corrosion in the form of
horseshoe-shaped grooves. On the other hand, Khatak and Gnanamoorthy [5] attributed leaks
developed at random locations in Al-brass condenser tubes after one year of operation to
crevice corrosion under seawater deposits. Furthermore, Chandrasekhariah and Mukherjee [6]
329
Seawater Corrosion
attributed the failure of Al-brass condenser tubes after six months of service to crevice
corrosion resulting from lodgments of organic deposits.
The aim of this paper is to establish a link between a failure investigation of Al-brass
tubes and a laboratory study on the effect of seawater pollutants. It was hopped that
establishing such a link would throw more light on the mechanism of failure.
EXPERIMENTAL PROCEDURE
Failure analysis was undertaken on ten failed Al-brass tubes made according to ASTM
C68700. The tubes were removed from the heat recovery stage of a desalination plant that
used treated seawater. The design flow velocities were 1.5-2.14 m/s, and the temperatures
were 42C at the inlet stage and 82.6C at the outlet stage. Visual, macroscopic,
metallographic and scanning electron microscopic (SEM) examinations were conducted on
the tubes before and after the removal of corrosion products. X-ray diffraction (XRD) and
energy dispersive spectroscopy (EDS) were used for the analysis of the corrosion products
and deposits. Also, chemical analyses were made to verify the materials conformity.
The laboratory corrosion tests were conducted under stagnant and flow conditions (0.1
and 2.2 m/s) using Arabian Gulf seawater at room temperature. The tests were made on fresh
(unused) Al-brass using clean seawater and seawater containing 5 ppm manganese or 4 ppm
chlorine. Chlorine was added in the form of sodium hypochlorite solution, and the
concentration of free chlorine was monitored using an ion selective analyzer and was
replenished daily. Manganese was added in the form of manganese chloride. The work
under stagnant conditions involved measurements of the open-circuit corrosion potential and
potentiodynamic polarization tests. The tests were made in duplicate using specimens in the
form of discs measuring 2 cm in diameter and 1 mm in thickness. Before the test, specimens
were mechanically ground using 800 grit silicon carbide paper, polished with 3 m diamond
paste, and ultrasonically cleaned with detergent and acetone. Teflon holders was designed to
expose a specimen area of 1.6 cm2. The potentiodynamic polarization tests were carried out
at a scan rate of 30 mV/min starting from a cathodic potential value of -700 mV relative to the
open-circuit potential and scanning was stopped at a potential of + 700 mV. A potentioscan
with IR compensation controls, saturated calomel reference electrodes (SCE) and cylindrical
graphite counter electrodes were used in these experiments.
A circulating test rig in the form of a flow loop made of PVC pipes was used to carry out
the work under flow conditions. The rig was designed in such a manner that the Al-brass
tubes (10 cm in length, 1 mm in thickness and 1.6 cm in outer diameter) were exposed to
laminar flow at the same flow velocity. The tubes were internally ground with 600 grit
silicon carbide paper and soldered on the outside to copper wires to record the corrosion
potential. In this paper, average values of the open-circuit potential are reported.
At the end of the stagnant and flowing laboratory tests, the specimens were examined for
corrosion morphology and the composition of corrosion products. Again, SEM, EDS and
XRD techniques were used. The corrosion morphology was examined before and after
removing the corrosion products. The corrosion products were removed by immersion in 5%
citric acid for 24 hours, followed by ultrasonic cleaning in acetone.
RESULTS
Failure Investigation
330
Shalaby et al.
Visual observation showed that the internal surfaces of the failed tubes were covered by
pale green and orange, nonhomogeneous deposits mainly located at the mouth of the tubes
and occasionally in the middle of the tubes. The orange product was generally more adherent
than the green deposits. XRD and EDS analysis of the corrosion products indicated the
presence of a nonhomogeneous mixture of cuprous oxide and copper hydroxychloride
(paratachamite), in addition to sea salts such as calcium carbonate and magnesium hydroxide.
Inspection of the tubes after removal of the scales and corrosion products revealed
various localized forms of attack at the tubes mouth, in addition to metal thinning
downstream. In most of the tubes, the inlet edges suffered from inlet-beveling attack and
inlet edge cutting (Fig. 1), while at a distance of 3 cm from the inlet edges, localized craters
of various depths, shapes, sizes and angles (45-90 to the water flow direction) were located.
Perforations were found in some craters. Also, in some tubes containing horseshoe-shaped
grooves, perforations were apparent on the metal surface underneath the orange colored
product. Another form of localized corrosion (minute pits) was identified in many of the
tubes under scattered, localized black deposits. Inspection was also conducted on unused Albrass tubes which showed the initiation of minute pits covered by a black corrosion product.
Metallographic cross-sections were prepared for areas that suffered from localized
corrosion and craters. Examinations of the cross sections revealed the occurrence of
dezincified and nonuniform porous surfaces as well as shallow pits in the -brass structure.
Examinations of polished longitudinal sections at the craters revealed the presence of
intergranular attack at the craters borders. Transverse sections at the same location did not
reveal the penetration of intergranular cracking.
Laboratory Corrosion Tests in Stagnant and Flowing Seawater
As can be seen from Figs. 2 and 3, the potential-time behavior of Al-brass exposed to
pollutant-free seawater under stagnant and 0.1 m/s flow conditions was about the same. The
initial average potentials showed slight ennoblement during the first few days of testing,
followed by a small active shift until a steady-state was reached. When the flow velocity was
increased to 2.2 m/s, the corrosion potential in clean seawater gradually shifted to more noble
values (Fig. 4).
Visual examination of the Al-brass tested in stagnant clean seawater revealed a surface
that was mostly yellow-brown in color and contained a few small green precipitates which
increased in number and became darker in color on tubes exposed to seawater flowing at 0.1
m/s. On these latter tubes, beige and white precipitates were also observed. SEM
examination showed that the green precipitates were granular in nature, well compacted and
had formed on top of a thin, smooth, and adherent oxide film. EDS analysis indicated that the
green precipitates were rich in chloride and sulphur. After film removal with 5% citric acid,
the surface was free of any significant corrosion damage.
The tubes tested in clean seawater flowing at 2.2 m/s appeared to be similar to those
tested at 0.1 m/s. However, SEM examination showed that the surface film on the tubes
tested at 2.2 m/s had been stripped off from several areas, exposing the underlying bare metal.
Higher SEM magnification revealed that the bare surfaces had suffered from metal
dissolution that increased in intensity along the grain boundaries. A few scattered, small
shallow cavities were seen on the intergranularly attacked surface.
331
Seawater Corrosion
(a)
(b)
(c)
(d)
Figure 1. Photographs of forms of corrosion attack observed on the failed tube inlets: (a)
holes, craters and depression (1.1x); (b) horseshoe grooving and hole (1.8x); (c)
edge cutting and bevelling (8x); and (d) crater with elongated hole (10x)
The addition of 5 ppm manganese to stagnant seawater did not change the potential-time
behavior of Al-brass with respect to that in clean seawater (Fig. 2). On the other hand, the
presence of manganese increased the corrosion potential by 100 mV during potentiodynamic
332
Shalaby et al.
polarization in stagnant seawater (Fig. 5). It also shifted the cathodic branch of the
polarization curve towards higher current densities, eliminated the active/passive peak and
made the anodic peak to take place at slightly less positive potentials, suggesting selective
dissolution from the alloy. Optical microscopic examination of the sample used in the
polarization test revealed once again that general metal dissolution and intergranular attack
had occurred.
Figure 2. Potential-time behavior of Al-brass in stagnant seawater: (a) seawater; (b) seawater
containing 5 ppm manganese; and (c) seawater containing 4 ppm chlorine
Figure 3. Potential-time behavior of Al-Brass in seawater flowing at 0.1 m/s: (a) seawater;
(b) seawater containing 5 ppm manganese; and (c) seawater containing 4 ppm
chlorine
333
Seawater Corrosion
Figure 4. Potential-time behavior of Al-Brass in seawater flowing at 2.2 m/s: (a) seawater;
(b) seawater containing 5 ppm manganese; and (c) seawater containing 4 ppm
chlorine
Shalaby et al.
The effect of the addition of 4 ppm chlorine on the potential-time behavior of Al-brass is
shown in Figs. 2-4. In stagnant seawater, the potential underwent an initial ennoblement
during the first few days of testing which was followed by a shift towards active values till a
steady state was attained after about ten days of testing (Fig. 2). At the steady state, the
corrosion potential in the presence of chlorine was close to that in clean stagnant seawater,
indicating a negligible effect of chlorine. Statistical hypothesis testing also confirmed that
there was no significant differences at the l and 5% levels of significance.
In seawater flowing at 0.1 m/s, the addition of chlorine shifted the corrosion potential to
a noble value of about -100 mV after two days of exposure, and the potential remained close
to that value for the remaining period of testing (Fig. 3). At a 2.2 m/s flow velocity, the
potential-time behavior in the presence of chlorine was to a good extent similar to that
obtained in clean seawater at the same flow velocity (Fig. 4). Although potential fluctuations
occurred in both cases, the potential values were close to each other and remained relatively
stable after about ten days of testing.
SEM examination of the Al-brass tested under open-circuit conditions in chlorinecontaining stagnant seawater revealed features similar to those noted in clean seawater. On
the other hand, the surface of tubes tested in chlorine-containing seawater flowing at 0.1 m/s
was slightly greenish in color and contained a few green nodules. EDS of the nodules
revealed that they were enriched with chloride and sulphur. The surface appeared (under
SEM) to be covered by an adherent film, however, a few areas seemed to be covered by a
smooth, wavy scale layer. After removing the surface film, the bare surface was found to
have suffered from minor general corrosion associated with increased surface roughness in
the form of micro pits.
When the seawater flow velocity was increased to 2.2 m/s, the film formed in chlorinecontaining seawater became a thick, scale layer containing scattered mounds or nodules (Fig.
6b). In some areas, the scale looked like a layer of dried, broken mud, and in others it was
multilayered. The scale was not stripped off as in the case of clean seawater and seawatercontaining manganese flowing at the same velocity (i.e., 2.2 m/s), which suggests that the
scale was adherent to the surface. XRD analysis of the corrosion products scrubbed off the
surfaces of tubes after testing showed major peaks of copper hydroxychloride in addition to
cuprous chloride. After removing the scale, SEM examination showed that the bare surface
contained a significant number of relatively large isolated and interconnected cavities in pitlike shapes (Fig. 6c). Inside and around the cavities, the bare surface was porous (spongy) in
nature. However, away from the cavities, the surface appeared to be quite similar to that
observed after testing in clean seawater or in the presence of manganese.
335
Seawater Corrosion
(a)
(b)
(c)
Figure 6. SEM micrographs of Al-brass tested in seawater at 2.2 m/s, showing: (a) the
surface after testing in the presence of manganese; (b) nodules on top of the scale
formed in the presence of chlorine; and c) cavities observed after removing the
scale
The addition of chlorine to stagnant seawater shifted the cathodic branch of the
polarization diagram towards higher current densities (Fig. 5). It also caused the formation of
a small reduction peak. The addition of chlorine appears to diminish the passive region and
make the anodic peak take place at a slightly less positive potential than in clean seawater.
After the termination of the polarization test, microscopic examination revealed the same
featues as those observed in clean seawater.
DISCUSSION
Service Failure of Al-brass
It has been reported that the good performance of copper alloy tubing in desalination
plants is due to the formation of a protective film composed of cuprous oxide [1]. Other
deposits on top of the film, such as cupric oxychloride, cupric hydroxide, copper carbonates
and iron oxides, may also contribute to the corrosion protection. In fact, the corrosion
products on the surface of the field-failed tubes were a nonhomogeneous mixture of cuprous
oxide, copper hydroxychloride and paratachamite, in addition to sea salts such as calcium
carbonate and magnesium hydroxide. The nature of these scales appeared to be inadequate to
protect Al-brass in Arabian Gulf seawater.
Visual inspection of the failed tubes showed that inlet edge cutting and bevelling had
occurred in most of the tubes, while typical horseshoe grooving was evident in some tubes.
All these forms of attack were indicative of flow velocity related problems at the tube inlets
336
Shalaby et al.
only, although the flow velocity inside the tubes was within the safe range specified for Albrass (2.4 m/second) [1].
The design of the water-box inlet and baffles may create local turbulent flow patterns
that exceed the maximum allowable flow velocity to avoid erosion-corrosion. Sato and
Nagata [7] reported that the water velocity passing a partial obstruction in the bore of a
condenser tube can reach 8 m/second even though the overall velocity is in the range of 2
m/second. The existence of lodgments such as shells, biofouling deposits or corrosion scales
may also create areas of localized high velocity and turbulence leading to localized corrosion
and under-deposit attack. In the present failure case, crevice corrosion was observed under
lodgments, and the surfaces of the creviced areas were porous in nature, suggesting the
occurrence of dealloying. Similar results were noted by Efird and Verink [8], and Schleithoff
and Schmitz [9] where the type of attack in the crevices was dealloying. Schleithoff and
Schmitz [9] indicated that the presence of magnesium in the alloy was responsible for the lose
of arsenic which was added to prevent dezincification. On the other hand, it has been
reported [10] that in the crevice attack of copper alloys exposed to flowing seawater, cuprous
ions are produced within the crevice and react with chloride ions to form ionic copper
chloride complexes, leading to local acidification and enhancement of corrosion.
Examinations of metallographically polished sections from areas that had suffered from
crevice attack revealed the presence of intergranular corrosion and cracking. Todd [11]
reported failure of Al-brass tubes exposed to polluted seawater in a desalination plant. The
failure of the tubes was due to severe intergranular corrosion. In the present failure case,
minute pits were also observed under scattered and localized black sulphide deposits. Similar
attack was reported for Al-brass tubes in another application utilizing Arabian Gulf seawater
[4]. It has been reported that a copper sulphide deposit formed in polluted seawater is more
cathodic than cuprous oxide formed in clean seawater. Therefore, galvanic corrosion
between the base metal at breaks in the large areas of cathodic sulphide film can result in
rapid failure by pitting attack [12,13].
Effect of Seawater Pollutants
It is well established that Al-brass tubes perform satisfactorily if the seawater is clean,
i.e., not contaminated with any pollutants. Previous work [14] has shown that the major
constituent of the film formed in clean seawater is of the hydrotalcite family of basic mixed
hydroxy-carbonates [Mg6Al2(OH)16CO3.4H2O]. In the presence of an intermediate chlorine
level, the composition of the normal surface film changes. Francis [14] suggested that this
change is achieved by substituting increasing amounts of copper for magnesium and chloride
ion for the hydroxyl ion, resulting in a film with low resistance to mechanical damage.
However, there are confliting results on the effect of chlorine. Studies under stagnant or low
flow velocities have often resulted in reduced corrosion rates in the presence of chlorine
[15,16], while other work at higher velocities [17,7], has shown dramatically increased
corrosion.
Sato et al. [18] reported catastrophic damage to Al-brass tubes in chlorinated seawater,
caused by malignant impingement attack. They explained this phenomenon on the basis that
manganese ions present in seawater react with the residual chlorine from chlorination, and
thus MnO2 is formed as colloidal particles depositing on the corrosion product film and
forming an active cathode in areas of turbulence around lodgments. Consequently, galvanic
337
Seawater Corrosion
action is enhanced, leading to intensified erosion-corrosion damage. Gouda et al. [19] also
considered that the presence of significant amounts of manganese on the surface of failed Albrass condenser tubes used in a refinery in Kuwait as one of the factors contributing to
accelerated erosion-corrosion of the tubes. In all these failure investigations, the exact role of
manganese was not studied or clearly defined.
The above discussion suggests that the present failure case cannot be attributed to the
wrong choice of material. However, when using Al-brass, several precautions have to be
taken to ensure the long life of the tubes. Pollutant-free water should be used for hydrotesting
tubing followed by thorough drying prior to boxing for shipping. The circumstances of the
present failure case and the confleting results with regard to the effect of pollutants made it
necessary to carry out a systematic laboratory study on the effects of manganese and chlorine
on the corrosion of Al-brass. It was hoped that such a study might throw more light on the
exact role of seawater pollutants in the failure of the Al-brass tubes. The effect of sulfide
pollution was not studied, as it is well covered in the literature [12,13].
In the present laboratory work, the addition of 5 ppm manganese caused an
electropositive shift in the free corrosion potential reached during testing in seawater flowing
at 0.1 m/s. It also caused a similar shift under potentiodynamic polarization in stagnant
seawater. These results can be explained on the basis of the mixed potential theory and
morphological examination. According to Pourbaix [20], a slightly oxidizing agent such as
that of oxygen, can oxidize manganous solutions with the formation of solid oxides: brownblack Mn3O4, black Mn2O3 or various varieties of anhydrous or hydrated MnO2 which are
brown or black. These oxides are more noble than Al-brass, and their presence on the surface
of the metal is similar to that of a galvanic couple or the addition of an oxidizer to the system.
Under such conditions, the corrosion potential of the system is shifted to more noble values,
the corrosion rate is increased, and the hydrogen evolution rate is decreased.
The fact that the free corrosion potential was of the same order in stagnant clean
seawater and in seawater containing manganese could possibly be due to the lack of sufficient
diffusion of manganese (or manganese oxides) to the Al-brass surface. On the other hand, the
activation of the corrosion potential noted at a 2.2 m/s flow velocity could be due to the
stripping of the protective film, exposing fresh metal to the corrosive environment. The
increase in thickness of the surface film as a result of the addition of manganese would
increase the corrosion rate of the metal. The increase in film thickness might help the
stripping action which might result from the shear stress between the surface and the layer of
seawater closest to it. The increase in film thickness and its associated increase in corrosion
rate could be a factor in the development of the observed intergranular attack. Thus, the
present results suggest that the presence of manganese in seawater affects the growth and
stability of the protective layer.
The present laboratory work revealed the strong oxidizing effect of chlorine. This was
apparent from the electropositive shift in the corrosion potentials (Figs. 3 and 4) and the
cathodic depolarization relative to that in clean seawater (Fig. 5). Furthermore, the
morphological examination showed that the surface film formed in Al-brass in the presence
of chlorine was different than that formed in clean seawater or in the presence of manganese.
However, another scale layer which was different than the primary film was observed in some
areas (Fig. 6b). XRD showed that the corrosion products scrubbed off the surface of Al-brass
338
Shalaby et al.
were basically copper oxychlorides and copper chlorides. It appears that the film formed on
Al-brass changes in the presence of free chlorine. The presence of a totally different scale
layer of basic copper compounds in the form of multiple layers or nodules in localized areas
could significantly change the corrosion rate. The basic chloride nodules could act as sites
for further precipitation of other compounds, such as calcium carbonate, leading to
nonhomogeneous mixtures of several compounds, as was observed in the present failure case.
The presence of these nodules increases the local acidity underneath the scale, leading to
crevice corrosion, intergranular attack and dealloying, as was observed in both the laboratory
work and the field-failed tubes. Furthermore, the presence of these nodules could induce
localized increases in velocity and turbulence, resulting in erosion-corrosion at high flow
velocities.
CONCLUSIONS
1. The failure investigation revealed that the Al-brass tubes failed due to various forms of
corrosion. Crevice attack and erosion-corrosion of the horseshoe grooving type were the
most serious forms. Inlet edge cutting, inlet edge beveling, pitting, dezincification and
intergranular attack were also observed. The failure of the tubes was ascribed to
lodgments, increased local high velocities and turbulence.
2. The laboratory study indicated that the addition of 5 ppm manganese or 4 ppm chlorine
had little effect on the free corrosion potential of Al-brass in stagnant seawater. In
flowing seawater, manganese shifted the corrosion potential to more noble values at 0.1
m/s and to more active values at 2.2 m/s. Chlorine addition caused electropositive shift at
both flow velocities.
3. During potentiodynamic polarization, the presence of either pollutant caused cathodic
depolarization, electropositive shift of the corrosion potential and elimination of the
active/passive transition.
4. SEM examination of the laboratory tested specimens revealed that the film formed in the
presence of manganese was relatively thick and porous. The addition of chlorine caused
the localized precipitation of a scattered scale layer in the form of nodules of basic copper
chlorides. Similar to the field-failed tubes, crevice corrosion, intergranular attack and
dealloying were found beneath the nodules.
REFERENCES
1. H. Tuthill, Materials Performance 26, 9, 1987, pp. 12-22.
2. A.D. Little, Survey of Service Behaviour of Large Evaporative Desalting Plants, US
Department of Commerce, Office of Water Research and Technology, 1981.
3. V.K. Gouda and W.T. Riad, Kuwait Institute for Scientific Research, Report No. 2767,
1988.
4. V.K. Gouda, J.A. Carew and J.K. Cheriyan, Kuwait Institute for Scientific Research,
Report No. 2605, 1988.
5. S. Khatak and J.B. Gnanamoorthy, Failure of an Aluminium Brass Condenser Tube:
Handbook of Case Histories in Failure Analysis, Vol. 2, ASM International, Materials
Park, Ohio, USA, 1993, pp. 192-193.
339
Seawater Corrosion
340
ABSTRACT
Corrosion of steel reinforcement is a major cause of concrete deterioration in Kuwait and other
Arabian Gulf countries. The selection of effective repair schemes for corroding structures requires
that the corrosion damage be assessed and quantified.
The symptoms of corrosion-induced deterioration in two reinforced concrete structures in Kuwait
are documented and discussed. The investigative techniques employed identified the nature of the
service environment and its role in promoting corrosion of steel reinforcement in the concrete
structures. The failure to account for the service environment of the structures through
implementation of corrosion preventive measures contributed to the deterioration of the structures.
Both ingress of chloride ions and carbonation of the concrete were the causes of the corrosion-induced
deterioration.
Key Words:
INTRODUCTION
The service environment plays an important role in the durability and serviceability of
reinforced concrete structures. The Arabian Gulf region provides one of the most aggressive
environmental conditions for concrete structures. This environment is characterized by high
temperature and humidity cycles, and severe ground and ambient salinity with high levels of
chlorides and sulfates in the soil and groundwater. Such environmental conditions have
promoted an extensive degree of deterioration in concrete structures within 10-15 years of
construction [1]. Structures exposed to the marine environment, groundwater conditions and
industrial pollution have suffered the most.
In Kuwait, as in other Arabian Gulf countries, the symptoms of deterioration in
reinforced concrete structures have shown that corrosion of steel reinforcement is the major
form of deterioration [2]. Studies conducted on the conditions of marine and non-marine
structures in Kuwait have shown corrosion to be caused primarily by ingress of chloride ions
aided by carbonation and sulfate attack, while carbonation of concrete is a major cause of
corrosion in some non-marine structures. Cracking of concrete caused by sulfate attack can
facilitate the ingress of chloride ions. A visual inspection of selected structures showed
evidence of corrosion to be extensive (Fig. 1) and widely spread [3]. The observations made
341
during the visual inspection of these structures point to the vital role the service environment
played in the extent of corrosion-induced deterioration of the structural elements. The
discussions in this paper include information obtained from relevant data on the corrosioninduced deterioration of two reinforced concrete structures in Kuwait.
Fe + 4Cl
2
FeCl4 + 2OH
(1)
FeCl4
Fe( OH )2 + 4Cl
(2)
In Kuwait, the groundwater in the coastal zone generally contains high levels of
chlorides and sulfates. Typical values for five residential areas within the coastal zone are
342
presented in Table 1. Both the chloride and sulfate values for each area are either within or
above the ranges for onset of concrete deterioration in accordance with the Uniform Building
Code [5]. Whereas concrete distress caused by expansive sulfate attack is known to be
suppressed in the presence of chloride ions, the chlorides promote corrosion of steel
reinforcement [6,7]. As such, the groundwater in the coastal zone of Kuwait would be
expected to induce corrosion when in contact with unprotected reinforced concrete elements.
Table 1. Chloride and Sulfate Levels in Groundwater in Different Coastal Areas in Kuwait
Coastal Area
Sulaibikhat
Shuwaikh
Shaab
Salwa
Fahaheel
Ranges for onset of
concrete deterioration
Chloride (ppm)
10,423
642
41,126
752
3,092
500 - 1,500
Carbonation-Induced Corrosion
A second cause of corrosion in reinforced concrete is carbonation of the concrete cover
on the steel reinforcement. Atmospheric carbon dioxide (CO2) combines with moisture in the
concrete to form carbonic acid. This acid then reacts with the cement hydration products,
particularly calcium hydroxide (Ca(OH)2), to form calcium carbonate (CaCO3) and lower the
pH of the concrete.
CO2 + H2O + Ca(OH)2 CaCO3 + 2H2O
(3)
When the pH is lowered below 11.5 at the level of the steel reinforcement, the
passivating layer is destroyed causing corrosion to occur [4]. The rate of carbonation of the
concrete is influenced by the concentration of CO2 in the atmosphere, and by the diffusion
rate of CO2 which is dependent on the permeability and moisture content of the concrete. If
the moisture content of the concrete is very low, carbonation does not occur because of the
lack of water. If the moisture content is very high (i.e., saturated concrete pores), there is
again very little carbonation because of the very low rate of CO2 diffusion in water.
Carbonation is greatest where the pores of the concrete are partially filled with water.
Carbonation-induced corrosion in the Arabian Gulf region is usually due to insufficient
concrete cover on the steel reinforcement [6]. The low cover thicknesses seem to be the
result of a lack of an adequate specified minimum cover and poor control during construction.
In the United Arab Emirates (U.A.E.) and Bahrain [6,8], carbonation-induced corrosion has
been documented in interior concrete elements which received little or no curing. Studies in
Kuwait have shown that carbonation due to poor construction practices was the cause of
corrosion of non-marine concrete structures [2].
343
344
345
For the oil refinery structure, lower values for ultrasonic pulse velocity and rebound number
were obtained for structural elements with extensive cracking.
5000
Adjacent to Expansion Joint
Further from Expansion Joint
4000
3000
2000
1000
0000
Slab
Beam
Column
Structural Member
Figure 4. Ultrasonic pulse velocity data for concrete in different structural members
Concrete Cover and Carbonation Depth
A covermeter was used to determine the thickness of concrete cover provided on the
reinforcement to protect against corrosion. Core samples were removed from the structure to
determine the extent of carbonation of the concrete cover utilizing phenolphthalein solution.
Data obtained for the commercial building showed that carbonation depth exceeded the cover
thickness in some structural members, as illustrated in Fig. 5 for beams. In these members,
carbonation would be expected to contribute to corrosion of the reinforcement.
Concrete Quality
Cores were removed from selected structural members to assess water absorption and
voids content characteristics of the concrete in order to determine the ability of the concrete
to resist ingress of moisture and salts. The water absorption and voids content data indicated
that, overall, the concrete in the structures was highly porous. The water absorption values
for the concrete samples ranged from 6 to 8% and the voids content values ranged from 15 to
18%. These values are quite high and indicate that the concrete in the structures has a low
resistance to the ingress of moisture and chlorides.
Chloride Content of Concrete
Concrete powder samples within three depth ranges from the surface of the concrete (010 mm, 10-25 mm, and 25-50 mm) were obtained from selected structural members. These
samples were used to determine the acid-soluble chloride contents of the concrete to assess
the potential for reinforcement corrosion and concrete deterioration. The concentrations of
chloride in the structures were found to exceed the threshold values for initiation of corrosion.
346
Figure 6 shows a typical chloride concentration profile in the structural elements of the
commercial building. For the concrete in the commercial building, the threshold chloride
value is estimated to be 0.025% by mass of concrete based on the ACI Committee 222recommended acid-soluble chloride limit of 0.20% by mass of cement [12].
5
Concrete Cover
Carbonation Depth
Beam 1
Beam 2
Beam 3
Structural Member
Figure 5. Concrete cover compared with carbonation depths in beams
0.10
0.08
0.06
0.04
Estimated limit for corrosion initiation = 0.025% mass of concrete
0.02
0.00
0.5
1.75
3.75
347
Chloride Diffusion: The chloride diffusion model based on Ficks second law [13-15]
was used to determine the characteristics of chloride penetration into the concrete. The model
is expressed as
C = C o erfc
where C
Co
D
t
erfc
=
=
=
=
=
x
(4)
2 Dt
The chloride data was used with Eq. 4 to calculate values for D and Co by performing a
nonlinear regression analysis. These values were used with Eq. (4) in conjunction with the
threshold chloride value and the thickness of concrete cover to estimate the time to initiation
of corrosion in the structural elements of the commercial building to be in the range of 2-6
years. This indicates that corrosion started early in the life of the 25-year old building and,
therefore, measures could have been taken earlier to control its progress.
Table 2. Steel Section Loss Due to Corrosion
Structural
Member
Slab
Beam
Column
Original
Diameter of
Bar, d (cm)
1.0
1.6
1.4
1.6
1.0
2.0
2.0
1.4
1.0
1.0
1.8
1.8
1.0
1.0
1.0
Mass of Corroded
Bar/Unit Length,
ms (g/cm)
5.73
15.76
10.08
15.48
5.92
22.64
22.39
10.56
3.17
2.35
13.80
13.05
5.92
5.88
5.87
Average Reduction in
Bar Diameter, d (m)
366
22
1222
164
208
850
956
920
2834
3830
3048
3460
208
240
248
CrossSectional Area
Loss (%)
7.2
0.3
16.7
2.0
4.1
8.3
9.3
12.7
48.6
61.9
31.0
34.7
4.1
4.7
4.9
Loss of Steel Section: Some cores removed from the structural members contained
pieces of steel bars. These steel bars were cleaned using Clarke's solution [16] and weighed
to determine their mass loss per unit length. The relation between mass, volume and density
was used to calculate the average reduction in bar diameter based on the original diameter of
348
the steel bars and a density of 7.86 g/cm3 for the steel. The values of average reduction in bar
diameter were used to calculate the cross-sectional area loss of the steel reinforcement at
different locations in the structural elements, as presented in Table 2 for the commercial
building. The estimates for steel section loss were as high as 62% in parts of the commercial
building and 88% in parts of the oil refinery structure. At these levels of steel section loss,
extensive cracking of the concrete would be expected, as was observed in the structures.
Eq. 4 was used with the estimated values of D and Co to calculate the maximum chloride
concentrations at the level of the steel reinforcement. The values for the commercial building
are summarized in Table 3, in addition to values of average thickness of concrete cover,
average depth of carbonation and maximum section loss of steel reinforcement. These results
show that both chlorides and carbonation were responsible for corrosion of the steel
reinforcement. Chloride-induced corrosion is indicated where the maximum chloride
concentration at the level of the steel reinforcement exceeds the threshold value of 0.025% by
mass of concrete and the carbonation depth is less than the thickness of the concrete cover.
Carbonation-induced corrosion is indicated where the carbonation depth exceeds the cover
thickness and the chloride concentration is less than the threshold value.
Table 3. Extent and Cause of Corrosion of Reinforcing Steel
Structural
Member
Slab
Beam
Adjacent to
Expansion
Joint
Max. Chloride
Concentration at
0.001
Steel Level (%
Mass of Concrete)
Average Concrete
4.0
Cover (cm)
Average
4.5
Carbonation
Depth (cm)
Max. Steel
16.7
Section Loss (%)
Type of
Carbonation
Corrosion*
-induced
corrosion
Column
Further from
Expansion
Joint
1.540
0.003
0.058
3.0
3.0
4.0
0.0
4.0
4.2
61.9
12.7
4.9
Chlorideinduced
corrosion
Carbonationinduced
corrosion
Chloride-induced
corrosion with
carbonation
contributing
349
The information gained from the corrosion damage investigation provides the basis for a
successful repair of the structure. In general, the arrest of chloride-induced corrosion requires
the removal of chloride contaminated concrete around the steel reinforcement. This would
require the mechanical removal of the contaminated concrete or the application of an
electrochemical method for chloride removal. Carbonation-induced corrosion can be arrested
by installing surface barriers. Surface applied barriers which have low vapor transmission
allow the uncarbonated concrete to re-alkalize or increase the pH of the carbonated concrete,
pushing the carbonation front back toward the surface. The carbonation process in cracked
concrete can be arrested by using elastomeric membranes for crack bridging or by using crack
sealants. Electrochemical technology can also be used to transport alkalies into carbonated
concrete [17].
The following general guidelines are appropriate when repairing corrosion-induced
damage in reinforced concrete structures.
surface to ensure a good bond between the repair and the base concrete,
Whenever possible, cracked concrete cover should be removed to at least 2 cm
beyond corroded steel bars,
During repair of cracked concrete cover, all exposed, severely corroded
reinforcement (i.e., > 25% section loss) should be repaired by providing new
reinforcement,
After concrete repair, protective coating may be applied on the surfaces of the
structure to protect against the ingress of moisture, chlorides and gases, and
Periodic monitoring of the structure may be undertaken, following completion of
the repair work, to assess the extent of any further corrosion activity.
CONCLUSIONS
1. The following conclusions are drawn based on the discussions in this paper:
2. The investigative techniques employed provided information on the nature of the
service environment and its role in promoting corrosion of steel reinforcement in the
concrete structures.
3. Lack of adequate measures to mitigate the effects of the service environment
contributes significantly to corrosion-induced deterioration of reinforced concrete
structures in Kuwait.
4. Both chloride-induced corrosion and carbonation-induced corrosion are found to
occur in the structures.
REFERENCES
1. Rasheeduzzafar; F.H. Dakhil and A.S. Al-Gahtani, Deterioration of concrete structures in
the environment of the Middle East, ACI Journal 81, 1, 1984, pp. 13-20.
2. H.M. Shalaby, Case studies of corrosion and deterioration of reinforced concrete
structures in the State of Kuwait, First International Conference on Deterioration and
Repair of Reinforced Concrete in the Arabian Gulf, Bahrain, 1985, pp. 309-320.
350
351
ABSTRACT
Attack and disintegration of concrete structures under the influence of aggressive fluids, wet
gases, etc., are understood as corrosion of concrete. The corrosion of concrete is a chemical, colloidchemical process, yet often a physicochemical one, while that of concrete reinforcement is mainly
electrochemical.
Many sea harbor jetties, docking facilities and concrete-supported oil platforms are subjected to
the marine environment in the Persian Gulf, and therefore become corroded. In the present paper,
using an aerated synthetic seawater representative of Persian Gulf environment, we have tried to
investigate the time required for corrosive agents such as chloride and oxygen to penetrate through the
concrete. The influence of the concrete's cover depth and corrosion rate of the rebar has also been
studied.
Key Words: Concrete, reinforcement, concrete cover, seawater, corrosion
INTRODUCTION
In recent years, the performance of concrete in marine environments has assumed
considerable importance because of the offshore activity of gas and oil exploration in various
countries. Thus, concrete performance in marine environments has been investigated by
several researchers [1,2,31.
The interaction between the concretes service environment and the concrete itself can
lead to deterioration of reinforced concrete structures, and in some cases, render the structures
unsuitable for their designed purposes. The interaction is often with the chemical species in
the environment [4].
For concrete in a marine environment, there appears to be a direct correlation between
low permeability (i.e., high strength) and good durability. Therefore, concrete sea structures,
such as harbor structures and offshore platforms, are built using high quality concrete [5]. In
general, concrete is a fine, porous material. Pore sizes vary from a few angstroms to several
millimeters. This pore system is more or less filled with a solution which contains varying
quantities of salts.
The problems associated with the application of reinforced concrete in marine
environments are well known. These problems have led to extensive research on the
corrosion of metal in concrete structures. Concrete reinforcement is usually protected from
corrosion by the highly alkaline environment (pH about 11.5) of the concrete surrounding it.
353
As a result, the steel surface frequently develops a protective oxide layer which is difficult to
dissolve, and hence limits its disintegration [1,6,7]. Corrosion of the steel normally happens
either by the carbonation of the concrete around it which reduces the alkalinity, or through the
presence of even small quantities of chlorides in the concrete cover.
The depth of penetration of chloride is a function of time and the permeability of the
concrete [8]. Once the steel has become depassivated, the rate of corrosion will depend,
among other factors, upon the availability of moisture and oxygen near the steel surface
[9,10]. In the absence of either moisture or oxygen, corrosion will not occur.
The corrosion of steel causes the metal to be converted in different stages into various
ferric oxides and ferric hydroxide [11]. This change leads to an increase in volume. Damage
resulting from corrosion can also be seen in the form of cracks parallel to the embedded steel,
and finally cracking and spalling of the concrete which accelerates the rate of corrosion.
The corrosion of reinforcing steel in concrete results from an electrochemical process
[12] accompanied by anodic and cathodic reactions. Iron is transferred in the solution as
hydrated ions with two electrons left in the reinforcing steel. These two electrons are
transferred to the cathodic area to assimilate in the cathodic reaction.
EXPERIMENTAL PROCEDURE
The experiments performed were designed with two purposes: the first was to study the
time that a corrosive agent takes to penetrate through the concrete cover to the reinforcing
steel, and the second was to investigate the influence of the depth of cover for a fixed watercement (w/c) ratio.
Tests were performed on mortar specimens partially submerged in an aerated seawater
(Table 1). The mortar specimens were made with ordinary Portland cement and had w/c
ratios of 0.4, 0.5, 0.6, and 0.7, with a cement-sand ratio of 1:3.
Table 1 Chemical Composition of Artificial Seawater
NaCl
(g/l)
32
MgCl2.6H2
O (g/l)
6
MgSO4.7H2O
(g/l)
5
CaSO4.2H2O
(g/l)
1.5
KHCO3
(g/l)
0.2
The aggregate used was crushed stone, and it was used in a dry condition when the
concrete was mixed. The sand was ordinary local river sand. The specimens made were 20 x
55 x 80 mm with two round carbon steel bars 7 mm in diameter embedded symmetrically.
The steel bar was embedded 50 mm into the mortar, and to avoid the formation of a
differential aeration cell, the ends of the embedded bars were insulated with adhesive tape.
The Portland cement was cured at 20C for 28 days. Since the procedure required a constant
2
current density (mA/mm ) over the reinforcement surface, the specimens were exposed to
seawater in the tank for several days to obtain a uniformity of moisture in the concrete before
the impressed current was applied. Direct current (DC) was impressed on the specimen from
a DC rectifier, and a potentiometer was used to control the current applied to each specimen.
354
Current direction was so arranged that the reinforcing steel bars served as anodes and a
stainless steel rod was employed as a counter electrode to serve as a cathode (Fig. 1). The
potential of each specimen was measured daily using a saturated calomel electrode with a
voltmeter twice a day, and any drift was corrected by adjusing the potentiometer. Potential
readings were taken with the power on. The readings represented the polarization potential of
the reinforcement plus the voltage drop across any corrosion product film at the
reinforcement /cement interface.
In order to study the effect of different cover depths on the corrosion rate of reinforcing
steel, 200 x 300 x 125 mm slab specimens with a 25 mm pond cast on top were made from
Portland cement at a w/c ratio of 0.5. Each specimen contained two carbon steel electrode
rods of 3 mm diameters embedded at four depths of cover, i.e., 10 , 20 , 30 and 40 mm.
The electrochemical corrosion measurements of the embedded steel reinforcement were
carried out by means of polarization resistance measurements and rest potentials. The
corrosion rates were calculated from the polarization resistance value using the Stern-Geary
equation, i.e.:
Icorr = Iappl / 2.3 E (ca / (c + a))
(1)
Icorr was calculated on the assumption that both the anodic and cathodic Tafel constants, a
and c, had values of 120 mV/decade.
355
Concrete cracking due to corrosion of the reinforcement was observed after 14 weeks for
a w/c ratio of 0.4, after 10.5 weeks for a w/c ratio of 0.5, after 4.5 weeks for a w/c ratio of 0.6
and after 4 weeks for a w/c ratio 0.7. Therefore, the sharp rise in current in Fig. 3 is related to
the time the appearance of the cracks was observed. However, the failure of the concrete
356
specimen due to the corrosion of the steel reinforcement is related to the initial current of the
steel bar, and as can be seen, the initial current of the steel bar depends upon the w/c ratio of
the covered concrete. Therefore, for the reinforced steel embedded in the concrete with a
lower w/c ratio, the initial current was lower and it took a longer time for the corrosive agent
to reach the steel reinforcement and cause corrosion failure. The results of measurement of
the distribution of the corrosion potential and corrosion current density of the reinforcing
steel after 70 days of exposure for different cover thicknesses are shown in Figs. 4 and 5.
In the case of a cover thickness of 10 mm, the degree of corrosion was large, and the
specimen had a crack of about 0.2 mm due to the corrosion of the reinforcing steel. The
corrosion of the steel rebar at the location of the crack was particularly remarkable. On the
other hand, with an increased cover thickness of 40 mm, very little corrosion of the
reinforcing steel bar was observed.
Visual examination of the reinforcement bar after 70 days revealed a white deposit on
the surface. The amount of the deposit varied with the depth of the cover thickness. On
microscopic examination, the deposit appeared to be crystalline in structure and was very
dense in nature (Fig. 6).
Chemical analysis of the deposit showed that it consisted of a mixture of calcium
carbonate and magnesium hydroxide. Since seawater contains a lot of magnesium sulfate,
which is the most harmful salt as far as cement attack is concerned, it reacts with calcium
hydroxide and by substitution of the magnesium for calcium, secondary gypsum in flat prisms
and brucite Mg(OH)2 in superimposed platelets are formed (Fig. 7).
357
Figure 7. The dissolution of calcium hydroxide and the formation of secondary gypsum
CONCLUSIONS
Since seawater contains a lot of chloride in various forms as well as sulfate salts, the
initial period of attack is the time taken for the chloride and sulfate ions to penetrate from the
surface through the concrete cover and reach the steel reinforcement bar. During this period,
the steel is in the passive state until the threshold value of these aggressive ions is reached for
corrosion to initiate in the presence of oxygen.
A possible form of corrosion attack on the reinforcement in the initial stage was pitting
corrosion. There is good reason to assume that the number of pits was fairly high, as was true
in the case of a 10 mm cover thickness. Also, since the amount of available cathodic current
was constant, regardless of the number of pits, the average anodic current was small.
Therefore, the most important consequence of pitting is that oxygen is consumed in the
process, i.e., as oxygen is consumed, the steel potential drifts to a negative value and
corrosion takes place. Hence, the availability of oxygen is one of the main controlling factors
358
of the corrosion of steel rebar in concrete. The amount of corrosion discovered when the
reinforcement was removed was insignificant as the depth of cement cover increased, small
spots of corrosion products were in a few instances visible at the surface.
A high water-cement ratio makes concrete permeable enough for the aggressive ions to
penetrate to the reinforcing steel easily and then depassivate the reinforcement. Thus, as the
water-cement ratio of the concrete increases, the potential of the reinforcing steel becomes
less noble and the electric resistance of wet concrete drops due to yje low permeability which
accelerates the corrosion of reinforcing steel.
REFERENCES
1. P.K. Mehta and P.J. Monteiro, Concrete: Structure, Properties and Materials, 2nd ed.,
Prentice Hall, Englewood Cliffis, 1993.
2. P. Rodriguez, E. Ramirez and A. Gonzalez, Magazine Concrete Research 46, 167, June
1994, pp. 81-91.
3. O.A. Kayyali and M.N. Haque, Magazine Concrete Research 47, 172, Sept. 1995, pp.
235-242.
4. D. Bawega, H. Roper and V. Sirivivatnanon, Cement and Concrete Research Journal 23,
1993, pp. 1418 -1430.
5. H.H. Haynes, American Concrete Institute, Detroit, Michigan, USA, SP-65, 1982, pp. 2138.
6. C. Androde, Corrosion of Steel in Concrete: Monitoring Techniques, Report of the
Technical Committee 60-csc Rilem, Champman and Hall , New York, USA, 1988.
7. P. Lambert, C.L. Page and P.R.W. Vassie, Materials and Structures 24, 1991, pp. 351358.
8. C. Liam, S.K. Roy and D.O. Northwood, Magazine Concrete Research 42, 160, Sept.
1992, pp.205-215.
9. A. Gonzalez, A. Molina, E. Otero and W. Lopez, Magazine Conerete Research 42, 150,
March 1990, pp. 23-27.
10. C.L. Page and P. Lambert, Journal of Materials Science 22, 1987, pp. 942-946.
11. C.A. Lawrence, British Ceramic Proceedings, Cement and Concrete Association,
Wexham, UK, No.35, 1984, pp.277-293.
12. K. Okado and T. Miyagawa, American Concrete Institute, Detroit, Michigan, USA, SP65, 1982, pp.237-254.
359
ABSTRACT
To minimize the incidence of premature deterioration of concrete, issues that need to be carefully
attended to include the establishment of material specifications that match the severity of the service
exposure conditions, and the implementation of construction practices that enable the desired level of
durability to be obtained. The paper discusses the characteristics of concrete ingredients that relate to
corrosion-induced deterioration of reinforced concrete structures. The role of supplementary
cementing materials in enhancing the resistance of concrete to reinforcement corrosion and the effects
of high ambient temperatures on the corrosion-related behavior of the concrete microstructure are
discussed. Selecting appropriate concrete materials that compensate for the aggressiveness of the
exposure condition is a critical factor in ensuring the durability of reinforced concrete.
Key Words: Concrete durability, concrete materials, concrete quality, reinforced
concrete, reinforcement corrosion
INTRODUCTION
The performance of concrete under harsh service conditions, such as those prevalent in
the Arabian Gulf region, is controlled by the interaction between the concrete and the
environment. Corrosion of steel reinforcement has been established as the major cause of
premature deterioration of concrete structures in the Arabian Gulf states [1-5]. Reinforced
concrete structures constructed with a design life of 50 years or more have become
structurally unsound within 10 to 20 years. The factors that promote this premature
deterioration of concrete structures include the use of unsuitable concrete mix ingredients,
poorly designed concrete mixes, and improper concrete placement and curing.
Chlorides are the primary cause of corrosion in reinforced concrete structures in Kuwait
and other Arabian Gulf states, with carbonation as a secondary cause [1-3]. A number of
studies have evaluated the role of different concrete ingredients in enhancing the corrosion
resistance of reinforced concrete, as well as the corrosion performance characteristics of
concrete materials used in the Arabian Gulf region [6-10]. In this paper, the characteristics of
concrete ingredients with respect to corrosion of reinforcement are discussed. In addition, the
paper presents the basis for producing durable concrete that is resistant to reinforcement
corrosion in the hot and arid environment of the Arabian Peninsula.
361
CONCRETE MATERIALS
Aggregates
Aggregates used for concrete mixes in Kuwait and other Arabian Gulf states are
typically contaminated with dust and salts. To enhance the durability of concrete made with
these aggregates, it is prudent to wash the aggregates to remove or minimize the chloride and
sulfate salts. However, due to the scarcity of water in the region, the aggregates may not be
washed prior to use in the concrete mix [1,3,9], enabling the corrosive action of the chlorides
to commence at a very early stage when the concrete is still very weak and porous.
In Kuwait, the sand is usually washed, whereas the coarse aggregate is sieved to remove
dust prior to use in concrete mix. Table 1 shows the chloride and sulfate levels in washed
sand and sieved coarse aggregate used for a residential building project. While the chloride
levels are lower than the limits for concrete deterioration as specified by the CIRIA Guide
[11], the level of sulfate in the sieved coarse aggregate is greater than the CIRIA Guides
limit. Where cracking of concrete takes place due to high levels of sulfate contamination,
chloride ingress from the salt-laden atmosphere in the coastal zone can occur leading to
reinforcement corrosion. Therefore, adequate steps must be taken to minimize both chlorides
and sulfates in concrete aggregates.
Table 1. Chloride and Sulfate Concentrations in Aggregates
Material
Sand (Washed)
Coarse Aggregate (Sieved)
Limits for Concrete
Deterioration
Mix Water
Potable or desalinated water is scarce in the Arabian Gulf region. As such, brackish
service water (nondesalinated tap water) is sometimes used in mixing concrete [1,9]. This
practice introduces quantities of chloride and sulfate into the concrete at the time of mixing.
In a study undertaken by Rasheeduzzafar et al. [7], the chloride and sulfate concentrations in
brackish water used to evaluate the influence of construction practices on concrete durability
were 1294 ppm and 375 ppm, respectively, compared with corresponding concentrations of
32 ppm and 32.5 ppm in potable water. The salt concentrations in the brackish water are
within the ranges specified by the Uniform Building Code [12] for onset of concrete
deterioration. These ranges are 500-1500 ppm for chlorides and 150-1500 ppm for sulfates.
The chloride concentration of 1294 ppm exceeds the maximum concentration of 500 ppm
recommended by the CIRIA Guide for water used in mixing or curing reinforced concrete.
Use of mix water of drinking quality would reduce the risk of corrosion in reinforced concrete
structures.
Portland Cement
362
The major compounds in portland cement are tricalcium silicate (C3S), dicalcium silicate
(C2S), tricalcium aluminate (C3A) and tetracalcium aluminoferrite (C4AF). The C3A phase
has the ability to bind chlorides, resulting in the formation of insoluble calcium
chloroaluminate compound (3CaO.Al2O3.CaCl2.10H2O) or Friedel's salt. This reduces the
amount of free chloride ions in the concrete pores and, hence, lowers the corrosion risk.
Figure 1 shows that the concentration of free or unbound chlorides decreases with an increase
in the C3A content of cement [8]. The unbound chlorides were found to be 86, 58, 51 and
33% of the total chlorides in concrete made with cements having C3A contents of 2.04, 9.10,
11.02 and 14.00%, respectively.
Studies have shown that the time to initiation of corrosion increases with increasing C3A
content of cement [6,8]. However, the chloride-binding capacity of C3A decreases with an
increase in the chloride concentration, becoming almost ineffective when concrete is exposed
to high chloride concentrations [8]. In addition, the long-term effectiveness of chloride
binding by C3A in reducing corrosion risk is not yet clear, as the chlorides may be released
later in the life of the concrete structure due to carbonation or sulfate attack of the concrete
[13,14]. Thus, it appears that cements high in C3A should not be depended upon solely for
the purpose of reducing the risk of corrosion in reinforced concrete structures.
100
80
60
40
20
10
12
14
16
provisions for using concrete permeability characteristics, along with strength, to match
concrete quality to environmental exposure conditions.
CONCRETE MIX CHARACTERISTICS
Water-Cement Ratio
Lowering the water-cement ratio (w/c) of concrete reduces its permeability to ingress of
chloride solutions. Lower w/c concretes have a higher electrical resistivity which impedes
the flow of corrosion current. The rate of oxygen diffusion is also substantially reduced the
lower the w/c, contributing to significant enhancements in polarization resistance and,
thereby, to reductions in the magnitude of corrosion current.
Low w/c concretes are, however, limited in their effectiveness in delaying the onset of
chloride-induced corrosion. A reduction in w/c from 0.50 to 0.35 improved the time to
initiation of corrosion by only 20% [10]. This marginal increase in the time to corrosion
initiation is attributed to the fact that the reduction in the permeability of the concrete due to a
lowering of the w/c is less effective in the case of diffusivity of chloride solutions than in the
case of diffusivity of plain water [15]. That is, chloride ions in solutions, particularly in high
concentrations, are able to diffuse through concrete made with plain portland cement at much
faster rates than with diffusion of water. Enhanced resistance to chloride ion ingress is
obtained when supplementary cementing materials, such as silica fume, are used in the
concrete mix in addition to lowering the water-cementitious materials ratio.
Supplementary Cementing Materials
The permeability of concrete is significantly reduced when supplementary cementing
materials such as condensed silica fume, fly ash or blast furnace slag are used with portland
cement. The decreased permeability substantially increases resistance to chloride penetration
and reduces the rate of carbonation. The supplementary cementing materials produce
concretes with low chloride diffusivity and high electrical resistivity. A 9% replacement of
cement by silica fume reduced the chloride diffusivity by a factor of about 5 [16].
Figure 2 shows the increase in electrical resistivity of concrete with increasing content of
silica fume [17]. The effect is more pronounced the higher the cement content. For a 400
kg/m3 cement content, the increase in resistivity was 550 and 1600% for silica fume additions
of 10 and 20%, respectively. The times to initiation of corrosion for silica fume concretes
compared with plain cement concretes are presented in Fig. 3 [6], showing that silica fume
significantly delays the onset of corrosion. Figure 3 indicates that there may not be any
significant advantage in increasing the cement replacement by silica fume in Type I portland
cement concrete (C3A content of 9 to 14%) to more than 10%. This is of considerable
practical significance in the Arabian Gulf region, where the cost of silica fume is reported to
be over ten times the cost of ordinary portland cement [6]. A fly ash replacement level of
30% by mass of cement increased corrosion initiation time by a factor of about 2 [9]. For
blast furnace slag, effective replacement levels to reduce the risk of corrosion are 50 to 70%
by mass of cement [18].
The benefits of using supplementary cementing materials can only be fully realized if the
concrete is treated properly during construction. With regard to silica-fume concrete, for
example, the typical low water content and lack of bleeding may give rise to plastic shrinkage
cracking, particularly in the hot and arid environment of the Arabian Gulf region. Techniques
364
for dealing with this problem include starting the curing process early and using evaporationretarding materials. The implementation of good concrete construction practices that account
for the characteristics of the particular supplementary cementing material used are essential to
enhancing the resistance of concrete to reinforcement corrosion.
140
100 kg cement/cubic meter
250 kg cement/ cubic meter
400 kg cement/cubic meter
120
100
80
60
40
20
0
0
10
20
800
Plain Cement
10% Cement Replacement by Silica Fume
20% Cement Replacement by Silica Fume
600
400
200
10
12
14
16
365
with ferrous ions according to Eq. 1 [19] to produce a stable passive layer of ferric oxide
(Fe2O3):
2 Fe2 + + 2OH + 2 NO2 2 NO + Fe2O3 + H2O
(1)
The chloride and nitrite ions compete for ferrous ions. If the chloride ion concentration
is greater, the corrosion process will start. If, on the other hand, the nitrite ion concentration
is greater, passive layer will form to close off the iron surface. Equation 1 shows that during
the reaction between the nitrite and ferrous ions, the supply of nitrite is depleted. The
effectiveness of the calcium nitrite admixture, therefore, is dependent on an accurate
prediction of the chloride loading of the structure over its expected design life and, hence, on
the selection of an appropriate dosage of the admixture. In the hot and chloride-laden
environment of the Arabian Gulf region, selection of an appropriate amount of calcium nitrite
should be carefully considered for cost-effective use of the admixture.
CONCRETE PLACEMENT AND CURING
Concrete placement, such as placement with bucket or by pumping, should be carried out
in such a manner as to ensure that the concrete remains cohesive. Inadequate consolidation of
the in-place concrete contributes significantly to the corrosion-induced deterioration of
concrete structures. Poor placement and consolidation is manifested in the form of large
voids, extensive honeycombing, rock pockets and bugholes, resulting in concrete of high
permeability. The effect of consolidation on corrosion initiation was evaluated by
Rasheeduzzafar et al. [7]. The results showed that the time to initiation of corrosion increases
with the consolidation effort, which was taken as the length of time for consolidating concrete
specimens on a vibrating table. Full or 100% consolidation was reached when the emission
of air bubbles ceased and the concrete surface was covered with a thin layer of cement paste.
With 40, 60 and 70% of full consolidation effort, the time to initiation of corrosion is,
respectively, 60, 76 and 95% of the corrosion initiation time in specimens where full
consolidation is achieved.
Curing is essential to producing high-quality concrete, and even more so in the hot-arid
climatic conditions of the Arabian Gulf region where extremely rapid, excessive evaporation
of moisture occurs from concrete surfaces. Water lost by evaporative drying can seriously
hamper the cement hydration reactions and the filling of capillary pores by the hydration
products. Hydration can take place only when the vapor pressure in the capillaries is
sufficiently high (i.e., about 80% of the saturation pressure). Below 30% saturation pressure,
there is only negligible hydration [20]. As such, the initiation stage and duration of curing are
crucial to producing durable, corrosion-resistant concrete under the climatic conditions in the
Gulf region. The beneficial effect of moist curing on the time to initiation of corrosion was
demonstrated by Rasheeduzzafar et al. [7]. Figure 4 shows that the time to initiation of
corrosion increases with the length of the curing period.
Placement and curing of concrete under the high ambient temperature conditions in the
Gulf region can cause visible thermal cracking of the newly placed concrete. Also, concrete
exposed to such high ambient temperatures at early ages develops cracks within its
microstructure, as shown in Fig. 5. This early-age cracking can lead to ingress of chlorides
366
either from the salty groundwater or from the salt-laden atmosphere in the coastal zones of
the region. In addition, studies have shown that the higher the curing temperature, the higher
the porosity of concrete [21-23]. In a study of the microstructure of concrete cured to the
same degree of hydration at temperatures of 5, 20 and 50oC [21], the volume of hydration
products was found to decrease and the porosity was found to increase with an increase in
curing temperature (Table 2). This effect of the curing temperature on the microstructure
leads to increased chloride penetration of concrete cured at higher ambient temperatures. For
concretes of different compositions, the rate of chloride diffusion increased by a factor of at
least 3 when the curing temperature was increased from 23 to 70oC [22]. Hot weather
concreting measures as outlined by ACI [24] and CIRIA [11] need to be carefully followed to
minimize the detrimental effects of high ambient temperatures. In addition, supplementary
cementing materials may be used to mitigate the effects of elevated temperature curing.
120
100
80
60
40
20
10
15
20
25
30
367
Porosity (% vol.)
4.3
10.9
15.1
CONCLUDING REMARKS
Based on the discussions in this paper, the following comments are offered as
recommendations to reduce the risk of corrosion in reinforced concrete structures:
1. Adequate steps must be taken to minimize both chlorides and sulfates in
concrete aggregates,
2. Concrete mix water should be of drinking quality,
3. Concrete permeability characteristics should be considered along with strength
requirements when specifying concrete quality to match specific
environmental conditions,
4. Low w/c ratio concrete used in conjunction with supplementary cementing
materials is effective in enhancing resistance to reinforcement corrosion,
5. Adequate placement and consolidation is necessary to produce concrete with
low permeability to the ingress of chloride solutions,
6. Moist curing of sufficient duration is highly beneficial in delaying the onset of
corrosion, and
7. Measures necessary for hot weather concreting should be carefully
implemented to minimize the detrimental effects of high ambient temperatures
on concrete durability.
REFERENCES
1. Rasheeduzzafar; F.H. Dakhil and A.S. Al-Gahtani, Deterioration of concrete
structures in the environment of the Middle East," ACI Journal 81, 1, 1984, pp. 13-20.
2. H.M. Shalaby, Case studies of corrosion and deterioration of reinforced concrete
structures in the State of Kuwait, First International Conference on Deterioration and
Repair of Reinforced Concrete in the Arabian Gulf, Bahrain, 1985, pp. 309-320.
3. Z.G. Matta, Chlorides and corrosion in the Arabian Gulf environment, Concrete
International 14, 5, 1992, pp. 47-48.
4. A.A. Hamid, Improving structural concrete durability in the Arabian Gulf, Concrete
International 17, 7, 1995, pp. 32-35.
5. S. Al-Bahar and E. Attiogbe, Corrosion-induced deterioration of reinforced concrete
structures in Kuwait, Proceedings CONSEC 95, International Conference, K. Sakai,
N. Banthia and O. E. Gjorv, Eds, Sapporo, Japan, Vol.1, August 1995, pp. 564-573.
368
6. Rasheeduzzafar, S.S. Al-Saadoun and A.S. Al-Gahtani, Reinforcement corrosionresisting characteristics of silica-fume blended-cement concrete, ACI Materials
Journal 89, 4, 1992, pp. 337-344.
7. Rasheeduzzafar, A.S. Al-Gahtani and S.S. Al-Saadoun, Influence of construction
practices on concrete durability, ACI Materials Journal 86, 6, 1989, pp. 566-575.
8. Rasheeduzzafar, Influence of cement composition on concrete durability, ACI
Materials Journal, 89, 6, 1992, pp. 574-586.
9. S.E. Hussain and Rasheeduzzafar, Corrosion resistance performance of fly ash
blended cement concrete, ACI Materials Journal 91, 3, 1994, pp. 264-272.
10. O.S.B. Al-Amoudi, Durability of reinforced concrete in aggressive sabkha
environments, ACI Materials Journal 92, 3, 1995, pp. 236-245.
11. CIRIA, Guide to Concrete Construction in the Gulf Region, CIRIA Special
Publication 31, 1984.
12. Uniform Building Code, International Conference of Building Officials (ICBO),
California, 1991.
13. K. Treadway, Corrosion period, in: Corrosion of Steel in Concrete, RILEM Report of
Technical Committee 60 CSC, P. Schiessl Ed., Chapman & Hall, London, 1988.
14. W.G. Hime, The corrosion of steel: random thoughts and wishful thinking, Concrete
International 15, 10, 1993, pp. 54-57.
15. O.E. Gjorv and O. Vennesland, Diffusion of chloride ions from seawater into
concrete, Cement and Concrete Research 9, 1979, pp. 229-238.
16. O.E. Gjorv, K. Tan and M. Zhang, Diffusivity of chlorides from seawater into highstrength lightweight concrete, ACI Materials Journal 91, 5, 1994, pp. 447-452.
17. O.E. Gjorv, Effect of condensed silica fume on steel corrosion in concrete, ACI
Materials Journal 92, 6, 1995, pp. 591-598.
18. J. Geiseler, H. Kollo and E. Lang, Influence of blast furnace cements on durability of
concrete structures, ACI Materials Journal 92, 3, 1995, pp. 252-257.
19. J.M. Gaidis and A.M. Rosenberg, The inhibition of chloride-induced corrosion in
reinforced concrete by calcium nitrite, Cement, Concrete and Aggregates 9, 1, pp. 3033.
20. T.C. Powers, A discussion of cement hydration in relation to the curing of concrete,
Proceedings, Highway Research Board, Vol. 27, 1947, pp. 178-188.
21. K.O. Kjellsen, R.J. Detwiler and O.E. Gjorv, Development of microstructure in plain
cement pastes hydrated at different temperatures, Cement and Concrete Research 21,
1991, pp. 179-189.
22. R.J. Detwiler, C.A. Fapohunda and J. Natale, Use of supplementary cementing
materials to increase the resistance to chloride ion penetration of concretes cured at
elevated temperatures, ACI Materials Journal 91, 1, 1994, pp. 63-66.
23. H.H. Patel, C.H. Bland and A.B. Poole, The microstructure of concrete cured at
elevated temperatures, Cement and Concrete Research 25, 1995, pp. 485-490.
24. ACI Committee 305, Hot Weather Concreting, American Concrete Institute, Detroit,
1991.
369
Kuwait Institute for Scientific Research, P.O. Box 24885, 13109-Safat, Kuwait.
2
ABSTRACT
This paper presents the results obtained from a study of the corrosion behavior of annealed, halfhard and hard-drawn copper pipes in Kuwaits soft tap water at room temperature. Accelerated
electrochemical experiments and long-term immersion tests were used to evaluate the performance of
the copper pipes under stagnant and flow conditions. The free corrosion potentials reached during the
long-term immersion tests were close to each other regardless of the tempering state of the copper.
The copper pipes, however, suffered from mild general corrosion which was more apparent in the
hard-drawn material.
This result was further confirmed using inductively-coupled plasma
spectrometry (ICPS). Potential-step polarization experiments indicated that the hard-drawn copper
exhibited the highest anodic current densities and the least noble breakdown potential among the
investigated tempering states. At low frequency, the impedance of the as-received half-hard copper
was lower than that of the annealed and hard-drawn copper. However, the impedance measurements
showed deviations from capacitive behavior when pitting occurred on polished copper. The half-hard
copper exhibited the largest pits in terms of depth and diameter, followed by the annealed and harddrawn copper. The differences observed were explained in terms of the nature of the oxide film, the
tempering state of the copper and its purity.
Key Words: Copper pipes, tap water, general corrosion, pitting corrosion, polarization
behavior, impedance.
INTRODUCTION
Generally, copper plumbing tubes have a service life of several decades. In some waters,
however, pitting can occur. Pitting of copper was first recognized in the UK in the late 1940s
when annealed and half-hard tubes were reported to be perforated in cold, fresh, hard water
within one or two years of service [1]. The pits were hemispherical in shape and contained
cuprous chloride and oxide. They were covered with copper carbonate corrosion product.
This type of pitting has been termed type 1 in the literature. Susceptibility to this type of
pitting has been attributed to the formation of a carbonaceous film during annealing.
In the late 1960s, pitting of another type (termed type 2) was identified in Sweden [2] on
hard-drawn tubes exposed to hot, soft water with pH values of 5-7. The pits were deep and
narrow in shape. They were covered with basic copper sulfate corrosion product. According
to case studies performed in Japan [3], the susceptibility to type 2 pitting is highly dependent
on water quality, but is seemingly independent of the presence of carbon films.
371
A case study of the failure of copper tubes in the soft tap water of Kuwait revealed
characteristics which were different from those of types 1 and 2 [4]. The morphological
features of the pits were similar to those of type 1, while the water composition and the
corrosion products were those of type 2. Moreover, pitting occurred in cold and hot water
irrespective of the tempering state of the copper. These discrepancies promoted the present
authors to evaluate the corrosion behavior of annealed, half-hard, and hard-drawn copper
pipes in Kuwait's soft tap water.
EXPERIMENTAL PROCEDURE
The study was conducted on seamless copper water pipes made to ASTM B88-83a, type
L (annealed and hard-drawn) and to BS 2871 Part 1, type Y (half-hard). The pipes made to
ASTM B88-83a measured 28.57 mm in outer diameter and 1.27 mm in wall thickness, while
the pipes made to BS 2871 measured 28 mm in outer diameter and 1.2 mm in thickness.
Microscopic examinations of the as-received copper pipes revealed attack of grain boundaries
in the annealed copper; presence of a thick and porous film on the half-hard copper; and a
rough surface with longitudinal grooves on the hard-drawn copper (Fig. 1). The amount of
carbon present on the internal surfaces of the as-manufactured pipes was found to be 15.5,
6.75 and 3.15 mg/dm2 for the annealed, half-hard and hard-drawn pipes, respectively.
The pipes were tested under stagnant and flow conditions in laboratory tap water at room
temperature. Table 1 shows the chemical composition of the water used. Pipe sections,
measuring 10 cm each, were used in their as-received condition to study the corrosion
behavior of copper in stagnant tap water. The pipes were tested in horizontal position and
were connected with PVC pipes to form a U shape. The pipes were welded on the outside to
copper wires for measurement of the open-circuit potential and for conducting direct current
(DC) potential-step polarization experiments. At the end of the immersion period, the tap
water was chemically analyzed for its copper content using inductively-coupled plasma
spectrometry (ICPS).
A test rig was used to measure the open-circuit potentials of the as-received copper pipes
in flowing tap water. The rig was in the form of flow loops made of PVC pipes. The rig was
composed of a fiber glass tank (160 l capacity), a circulation pump, and six horizontal copper
pipes measuring 30 cm in length each. The pipes were connected in parallel with common
water inlet and outlet. The water tank contained a ball valve for maintaining the water level.
The time of water flow in the rig was automatically controlled using a timer switch. The
timer switch was adjusted to allow water to flow for 0.5 hours followed by a period of 5.5
hours of stagnation. The water flowed to waste after passing through the tubes. The flow
velocity in the rig was adjusted to 0.4 and 1.0 m/s using valves connected to the inlet and
outlet of the rig. The details of the test rig have been described elsewhere [5]
The potential measurements were performed against a saturated calomel electrode (SCE)
for a period of about 180 days. In the potential-step polarization tests, the pipes were left in
the stagnant water until their potential reached a quasi steady state before the application of
potential. This usually took a period of about 2 months. Polarization started from the
corrosion potential in the anodic direction in steps of 20 mV. The current was recorded after
10 minutes at each step of polarization. A scanning potentiostat and a strip-chart
potentiometric recorder were used, whereas graphite rods served as counter electrodes.
372
(a)
(b)
(c)
Figure 1.
7.6
540.0
30.0
37.0
135.3
86.3
49.0
80.2
373
SO42- (mgl-1)
SiO2 (mgl-1)
HCO3-/SO42-
118.0
2.1
0.31
After the termination of the tests, the specimens were left to dry in a desiccator. Optical
and scanning electron microscopy (SEM) were used to examine the surface. The depth and
diameter of the pits were measured using a micrometer attached to the optical microscope.
RESULTS AND DISCUSSION
Potential and Polarization Behaviors
Figure 2 shows the potential-time behavior of as-received copper pipes of different
tempering states during testing in stagnant tap water. It can be seen from the figure that the
potential was initially negative, but rapidly shifted to the positive direction within the first
few days of testing. It is apparent from the figure that the potentials became more or less
steady (with occasional fluctuations) after about 100 days of testing. The potentials reached
were close to each other regardless of the tempering state, being on the order of 5-15 mV.
The copper concentrations in the stagnant water were 0.7, 0.8 and 1.5 mg/l for the as-received
annealed, half-hard and hard-drawn copper, respectively. It is worth noting that the
concentration of copper in the water was higher for the hard-drawn material.
The same potential-time behavior as above was obtained during testing under a
flow/stagnation sequence at 0.4 and 1.0 m/s. Again, the tempering state of the metal did not
significantly affect the potential values at the steady state. However, the increase in flow
velocity appeared to slightly shift the steady state potentials to more positive values.
Optical microscopic examinations of the copper pipes used in the above measurements
revealed that the flow/stagnation sequence caused more precipitation of corrosion products
than full stagnation. The copper pipes tested in stagnant water experienced very little
corrosion, mostly in the form of bluish-green stains. On the other hand, a significant amount
of bluish-green corrosion products were observed on the internal surfaces of the copper pipes
tested under flow/stagnation sequence of tap water. The precipitated corrosion products were
more pronounced on the lower halves of the pipes. They covered a large area of the surface
and were not in the form of mounds as is usually observed during pitting of copper. The
amount of precipitated corrosion products was observed to be more in the hard-drawn pipes
than in the half-hard and annealed ones.
374
Figure 2. Potential-vs-time curves for as-received copper pipes tested in stagnant tap water
Figure 3 shows potential-vs-current curves obtained during potential-step polarization
tests carried out on as-received copper pipes in stagnant tap water. The hard-drawn copper
exhibited the highest anodic current densities and the least noble breakdown potential among
the investigated tempering states. The hard-drawn copper was followed by the annealed and
half-hard copper in terms of the noble shift in the breakdown potential. Optical examinations
showed the presence of scattered and agglomerated small cubic crystals on the surfaces of the
annealed and hard-drawn materials. The oxide layer that was observed on the as-received
half-hard material before the start of the test became less porous and more diffuse after the
test, suggesting that the generated current was consumed in repairing the highly defective
oxide layer. No pitting corrosion was found in the as-received materials.
The present results suggest that hard-drawn copper is somewhat more prone to corrosion
than half-hard or annealed copper in Kuwait's tap water. Since general corrosion was only
observed during the testing period, the attained results do not necessarily imply that harddrawn tubes are more susceptible to pitting than the other tubes in the soft tap water of
Kuwait. In the case of copper pipes tested in hard waters, Devroey and Depommier presented
evidence to show that hard-drawn tubes were more resistant to pitting than half-hard tubes,
which were in turn more resistant than annealed tubes (unpublished data). Cornwell et al. [6]
attributed these differences to carbon deposits on the surface of the annealed tubes which
were formed during bright annealing operations. The superior performance of the hard-drawn
tubes, on the other hand, was attributed to a protective effect exerted by the drawing lubricant
in the pores of the hard-drawn tubes. In the case of soft water, such as in Kuwait, Sato et al.
[3] indicated that the susceptibility to pitting is highly independent of the presence of carbon
film. In such cases, it is possible that the stored energy within the metal due to the
manufacturing process of the hard-drawn tubes, becomes an activating factor for corrosion.
375
376
An attempt was made to study the kinetic behavior of the pitting of copper using
impedance spectroscopy. Figure 5 shows the impedance spectra in Bode format obtained for
polished annealed copper after free corrosion and potentiostatic polarization in stagnant tap
water at 200 mV for 4 and 6 days. The overall behavior of the impedance-vs-frequency
curves was similar in all cases with the exception of a slight change for the specimen tested
under free corrosion condition in the frequency range of 1 < f < 1000 Hz. On the other hand,
a significant change is noted in the phase angle-vs-frequency curves. Potentistatic
polarization appeared to cause a decrease in the phase angle peak which is associated with a
shift towards higher frequencies. Furthermore, the low frequency part of the spectra changed
in a manner which suggested that pitting had occurred. A comparison of Figs. 4 and 5
indicates that when the air-formed oxide film was removed by polishing, the impedance of
the material decreased significantly.
The AC impedance technique has been found to be successful in investigating the
kinetics of general corrosion [11]. Recently, however, some investigators [12,13] have shown
that the technique can be used to detect the initiation and growth of pitting. The present
results also indicate that the impedance technique can be a useful tool for the study of pitting
of copper in tap water. The results showed that a dominant capacitive behavior existed in the
case of polished copper immersed in tap water under free corrosion conditions. This suggests
that the surface of copper is to some extent blocked by the surface film under these
conditions. On the other hand, deviations from the capacitive behavior are noted in the case
of polarized copper specimens (Fig. 5). These deviations can signify the presence of pitting.
They are possibly caused by a diffusion process through the porous oxide scale which was
elevated from the metal surface.
Figure 5. Bode-plots for polished annealed copper tested in stagnant tap water
after different testing conditions.
377
(a)
378
(b)
Figure 6. Percentages of pits of: (a) different depths, and (b) diameters, grown on
polished annealed, half-hard and hard-drawn copper during
potentiostatic polarization in tap water at 200 mV for 4 days.
The fact that the hard-drawn material exhibited smaller diameter pits is readily
explainable in terms of the large deformation of the grains. On the other hand, it is rather
difficult to explain the behavior of the half-hard copper. The differences in behavior could
possibly be due to differences in the alloying elements and not the carbon content. The purity
of the phosphorus de-oxidized annealed and hard-drawn copper (high residual phosphorus)
was 99.9%, whereas the purity of the half-hard copper was 99.85. Pipes made of the former
only contain phosphorus and silver as residual elements, whereas pipes made of the latter
contain phosphorus, arsenic, antimony, bismuth, iron, lead, etc. The present work also
showed that the number of pits did not increase with increases in the polarization time,
suggesting that the number of pitting sites is more or less the same regardless of the
differences in manufacturing procedure and carbon content. These results lend support to the
observation made by Sato et al. [3] that pitting corrosion of copper in soft tap water appears
to be independent of the presence of a carbon film on the metal surface.
In a previous work [9], the present authors showed that pitting corrosion of copper starts
at the grain boundaries. Since there are no data available in the scientific literature with
regard to the diameter or depth of pits developed in copper in tap water, the authors assumed
that the cross-section of a pit grown along the grain boundaries of hard-drawn copper would
appear deep and narrow. Thus, the authors postulated that the shape of the pits depends on
the deformation of the grains. The present results provided the needed experimental proof
that the shape of the pits depends on the tempering state of the copper and not on the type of
water as was assumed previously [14].
For copper, which is rarely passivated, the mechanisms for pitting and general corrosion
seem to be different than those of passivable metals, such as stainless steels. In the presence
of the oxide film formed during manufacturing, as-received copper was found to experience
corrosion of a general nature while under anodic polarization. Thus, the protective oxide film
on copper functions not by making the corrosion rate minimal as in the case of passivable
metals, but by scattering the dissolution process to become through large amount of pores. In
the case of the polished material, a reddish-brown scale was formed. This scale separated
from the metal surface, creating the occluded cell required for pitting initiation. Thus, the
disbondment of the oxide film creates the requirements necessary for pitting corrosion to
occur.
CONCLUSIONS
1. During long-term immersion tests, the free corrosion potentials of the as-received
annealed, half-hard and hard-drawn copper were close to each other regardless of the
tempering state of copper. The copper pipes, however, suffered from mild general
corrosion which was more apparent in the hard-drawn material. This result was
further confirmed using ICPS.
2. At low frequencies, the impedance of the as-received half-hard copper was lower than
that of the annealed and hard-drawn copper. When pitting occurred on polished
379
copper, the impedance measurements showed deviations from the capacitive behavior.
These deviations were attributed to a mass transport phenomenon through the porous
oxide scale. The AC impedance technique was found to be useful in studying the
pitting of copper.
3. The half-hard copper exhibited the largest depth and diameter of pits followed by the
annealed and hard-drawn copper. The number of pits was about the same (7-10
pits/cm2) for all types of copper and remained unchanged with increases in
polarization time. The difference in the size of pits was ascribed to the degree of
purity of the copper.
ACKNOWLEDGMENT
The authors of this paper would like to acknowledge the Kuwait Foundation for the
Advancement of Science for its financial support of this work through contract project No.
87-08-06.
REFERENCES
1. H.S. Campbell, Journal Institute of Metals 77, 1950, p. 345.
2. E. Mattsson and A.M. Fredriksson, British Corrosion Journal 3, 1968, p. 246.
3. S. Sato, T. Minamoto, K. Seki, H. Yamamoto, Y. Takizawa, S. Okada, S. Yamauchi,
Y. Hisamatsu, I. Suzuki, T. Fujii, T. Kodama, H. Baba and K. Nawara, Proceedings
International Symposium on Corrosion of Copper and Copper Alloys in Building,
Tokyo, Japan, 1982, p. 17.
4. F. Al-Kharafi, H.M. Shalaby and V.K. Gouda; Proceedings 10th International
Congress on Metallic Corrosion, Madras, India, November 1987, p. 767.
5. F.M. Al-Kharafi and H.M. Shalaby, Corrosion 51, 1995, p. 469.
6. F.G. Cornwell, G. Wildsmith and P.T. Gilbert, British Corrosion Journal 8, 1973, p.
202.
7. V.F. Lucey, British Corrosion Journal 2, 1967, p. 175.
8. J.R. Rossum, Journal American Water Association 77, 1985, p. 70.
9. H.M. Shalaby, F.M. Al-Kharafi and V.K. Gouda, Corrosion 45, 1989, p. 536.
10. M. Pourbaix, Corrosion 25, 1969, p. 267.
11. D.C. Silverman and J.E. Carrico, Corrosion 44, 1988, p. 280.
12. M. Keddam and R. Oltra, Materials Science Forum 8, 1986, p. 167.
13. F. Mansfeld and H. Shih, Journal Electrochemical Society 135, 1988, p. 1,171.
14. E. Mattsson, Corrosion Australasia 6, 1981, p. 4.
380
ABSTRACT
Vanadium is an important transition metal used in various industrial applications; especially as a
structural material in metallurgical applications. The electrochemical behavior of vanadium is an
important subject due to its application in redox flow batteries. The behavior of the metal in aqueous
solutions of different pH in oxygen-saturated and oxygen-free electrolytes was investigated. The
behavior of vanadium electrodes in alkaline solutions (pH > 8) differed from its behavior in acidic or
neutral solutions (pH 1-8). Open-circuit potential measurements revealed that the steady-state
potential was a linear function of the solutions pH. The slope of the linear relation changed from 0.039 V/decade for solutions of pH < 8 to -0.058 V/decade for solutions of pH > 8.
Electrechemical impedance spectroscopy, which represent an effective method for studying
corrosion phenomena, has shown that the metal undergoes active dissolution in aqueous media. In
solutions of pH > 8, the corrosion behavior of the metal can be simulated to a Randles equivalent
circuit model. In oxygen-saturated solutions, the electrodes surface is covered with a thin oxide film.
The interaction of this film with the ambient electrolyte depends on the solutions pH. Polarization
measurements have shown that the rate of corrosion in acidic solutions is not affected by the
prevailing gas. In alkaline solutions, the removal of air or oxygen from the ambient electrolyte leads
to a decrease in the corrosion rate.
Key Words: Corrosion, electrochemistry, impedance, passivity, polarization, vanadium
INTRODUCTION
Vanadium is an important transition metal due to its use and the use of its alloys as
structural materials not only in metallurgical applications but also in nuclear reactors [l]. The
metal ions are used extensively in redox flow batteries [2-5]. Unlike many transition metals,
vanadium shows active behavior [6-10]. The electrode potential of vanadium and the effect
of oxygen on this potential were the subjects of the very early studies concerning this metal
[11,12]. The active behavior of vanadium and its anodic dissolution in aqueous solutions was
investigated [13,14]. It was found that the rate of metal dissolution is independent of the
hydrogen ion concentration or the nature of the anions present. The rate determining step was
+
a monovalent adsorbed intermediate (V ads) [14]. Investigations of the anodic behavior in
acidic solutions containing different anions and cations have shown that the metal undergoes
2+
active dissolution in all acidic solutions except those containing Ba at a pH > 4, and that the
active dissolution of the metal occurs through a monovalent intermediate [15]. The behavior
of the metal in both acidic and basic media was found to obey the Tafel approximation of the
Butler-Volmer equation over a wide range of potentials [16]. Extensive studies have been
383
Fundamental Aspects
carried out in glacial acetic acid and have shown oxide film formation in the presence of
sodium borate and water [17,18,19].
The present investigation was aimed at throwing more light on the electrochemical
behavior of vanadium in aqueous solutions and on the effect of solution pH and oxygen on
the corrosion and passivation processes occurring at the electrode/electrolyte interface.
EXPERIMENTAL PROCEDURE
Massive, cylindrical, spectroscopically pure, vanadium rods (Alderich-Chemie) were
used as working electrodes; they were mounted in glass tubes of appropriate internal diameter
2
with an epoxy resin leaving a front surface area of 0.302 cm to contact the electrolyte. An
all glass three electrode cell with a large surface area, Pt, counter electrode and a Ag/AgCl/Cl
(3 M KCl) reference electrode was used. The solutions were prepared from analytical grade
reagents and triple distilled water. The buffer solutions covering a pH range of 1-13 were
prepared according to Clark and Lub's series [20]. The pH of each solution was controlled
before each experiment, and the electrodes were mechanically polished with successive
grades of emery papers down to 1200 grit, then wiped with a smooth cloth and washed with
triple distilled water. In this way, the electrodes acquired reproducible, bright silvery
surfaces. After polishing and rinsing, the electrodes were immersed directly in the test
solutions. Electrochemical impedance spectroscopy (EIS) investigations were carried out
using the IM5d-AMOS system (Zahner Elektrik GmbH & Co., Kronach, Germany). The
5
input signal was usually 10 mV peak to peak in the frequency domain of 0.1-10 Hz.
Frequencies down to 0.1 MHz were also investigated. Polarization measurements were
performed using an EG&G (Princeton Applied Research) model 273A
Potentiostat/Galvanostat
interfaced to an IBM PS3 computer.
The potentiostatic
measurements were traced using programs that enable ohmic drop compensation. The
steady-state potential, ESS, measurements were controlled separately using a high impedance
value voltmeter (Keithley type 197A Autoranging Multiplier, England). All measurements
were carried out at constant room temperature of 22oC. The potentials were measured against
the Ag/AgCl/Cl- reference, and then refered to the normal hydrogen electrode (nhe). The
gases used for deaeration or solution saturation were purified and dried before being bubbled
in the electrolytic cell. The gas was bubbled for at least 20 min. in the test solution prior to
each experiment. The details of the experimental procedures were as described elsewhere
[10,21].
RESULTS AND DISCUSSION
Steady-State Potential Measurements
The potential of the vanadium electrode was traced over a period of 180 min. in naturally
aerated aqueous solutions covering a pH range from 1 to 13. In all solutions, the electrode
potential became more positive with time. A typical example of the variation of the electrode
potential with immersion time in the buffer solutions is presented in Fig. 1A. In this figure,
the results in solutions of pHs 2, 7 and 12 are presented. The steady-state potential, Ess ,
measured after 180 min. of electrode immersion in each solution is plotted against the pH of
the solution, and is presented in Fig. 1B. The results reveal that ESS is pH-dependent over the
384
Badawy et al.
whole pH range. The Ess versus pH relation is linear and can be presented by an empirical
equation of the form:
Ess = a - b pH
(1)
where a is a constant representing the value of ESS extrapolated from the linear relation at pH
= 0. As can be seen from Fig. 1B, the ESS versus pH relation has an inflection between pH =
8 and pH = 9 which means that the slope, b, changes. In the basic medium, i.e., pH > 8, the
slope of the linear relation is very close to the value of 0.059 V/pH, which was calculated
from the Nernst equation for a pH indicator electrode with one electron electrode process at
o
25 C according to:
o
E = E - 0.059 pH
n
(2)
(3)
(4)
The steady-state potential values obtained according to Eqs. 3 and 4 are quite different
2+
from the standard electrode potentials assigned for the systems V/V (Eo = -1.19 V) and
2+ 3+
o
V /V (E = - 0.26 V) [22]. This supports the notion that the electrode process cannot be
represented by a simple equilibrium relationship such as that given for the simple redox
2+
2+ 3+
equilibria of the metal and its ions, e.g., the V/V or V /V Systems. This can be
understood on the basis that the solution does not contain significant concentrations of those
ionic species, and that the electrodes surface is covered by a thin oxide film in aqueous
solutions. Consistent with this is the dependence of the steady-state potential on the
prevailing gas and the stirring conditions of the solution.
Fundamental Aspects
The electrodes potential was traced in naturally aerated, oxygen-saturated and oxygenfree solutions of different pHs. Oxygen was removed from the solution by bubbling N2 or H2
at least 20 min. before electrode immersion. A typical example of the results in solutions of
pH = 12 is presented in Fig. 2. The results reveal that the electrodes potential is sensitive to
the oxygen concentration in the solution. Under all conditions, the potential became more
positive with immersion time until it reached a steady-state value. The use of either N2 or H2
to remove oxygen from the solution did not produce any remarkable difference; the steadystate potential lay, in both cases, in approximately the same range ( -385 mV (nhe) in pH =
12). In oxygen-saturated solutions, the Ess shifted in the positive direction by 100 mV.
This shift can be attributed to the presence of a thin oxide film on the electrodes surface.
The same trend was observed over the whole pH range from 1 to 13.
The sensitivity of metals with active/passive transitions towards oxygen is well known,
especially for those which do not show active dissolution like niobium, tantalum and titanium
[10,21,24]. The passivation of vanadium in aqueous solutions was discussed very early by
386
Badawy et al.
Muthman and Frauenberger [11]. Later, it was suggested that the passivity is due to the
presence of a gaseous film [12]. Unlike many transition metals, vanadium has an active
corrosion behavior with a limited tendency for passivation. The passivation behavior of the
metal was explained earlier by the presence of a chemisorbed oxygen film [25]. Dry or moist
o
oxygen did not tarnish the polished metals surface, and even hot water (60-85 C) had no
effect on the surfaces brightness. The decrease of the steady-state potential on oxygen
removal by bubbling of N2 or H2 in the test solution can be considered as an indication of the
presence of a thin oxide film on the electrodes surface. The oxide film formed represents a
non-stoichiometric oxidation state of the metal which is responsible for the observed behavior
of the metal in each solution. Removal of oxygen by bubbling of N2 or H2 in the solution
leads to dissolution of the formed oxide, and hence, a decrease of its thickness leading to a
shift of the steady-state potential in the negative direction (Fig. 2), and the following
equilibrium state is shifted to the left:
2V + xO2 2VOx
(5)
(6)
The value of x in this case, and hence, the value of n of Eq. 2, can be calculated from the
slope of the first segment of the steady-state potential/pH relation (Fig. 1B), i.e., in the pH
range of 1-8.
slope = -0.039 V = - 0.059
n
In basic solutions, the interaction between the electrodes surface and the solution occurs
through OH ions according to:
-
(7)
The lower oxides of vanadium are basic and very unstable [25]; therefore, they cannot
protect the metal from corrosion as in the case of the valve metals with active/passive
transitions.
Fundamental Aspects
relaxation times that vary over several orders of magnitude and permits single averaging,
within a single experiment to obtain highly precise levels. The open-circuit impedance of
vanadium electrodes was traced for 180 min. after electrode immersion in the test solutions.
Typical data for pHs of 2, 7 and 12 are presented as Bode plots in Fig. 3.
(A) in solution of pH 2
(B) in solution of pH 7
(C) in solution of pH 12
Figure 3. Bode plots of the vanadium electrodes in naturally aerated solutions at different
time intervals from electrode immersion
() 15 min. () 60 min. (----) 130 min.
Bode plots are recommended as standard impedance plots since the phase angle, , is a
sensitive parameter for indicating the presence of additional time constants in the impedance
spectra [10,26-28]. It employs frequency as an independent variable, so that a more precise
comparison between experimental and calculated impedance spectra can be made [29-31].
The use of the log versus log format enables equal representation of all experimental data
over the whole frequency domain.
388
Badawy et al.
The EIS spectra in Fig. 3 contain only one capacitive contribution represented by the
linear variation of the electrodes impedance, Z, with the frequency, f, [26-28]. In acidic and
neutral solutions (pH = 1-8), there is a part of the spectrum where the phase angle is
independent of frequency (Fig. 3a and b at f < 1 Hz). Such behavior is explained by the
assumption of frequency dispersion and surface inhomogeneity [29]. For such systems, the
electrode impedance is given by:
Rp
Z =
I + (sCRP)
(8)
(9)
1 and = 2 f.
The value of the fit exponent corresponds to the extent of dispersion and is attributed
to surface inhomogeneity [29,30]. A nonlinear concentration of metal ions will occur, since
preferential charge transfer takes place at active sites. The impedance spectra of Fig. 3 show
that there is an active dissolution of the metal, as can be identified by the decrease of the
polarization resistance with immersion time in each solution.
The rate of dissolution is limited and is dependent of the solutions pH. The impedance
spectra of the electrodes in solutions of pHs of 2, 7 and 12 after 180 rnin. of electrode
immersion are collectively presented in Fig. 4. The results show clearly that the behavior of
vanadium in basic solutions is different from its behavior in acidic or neutral solutions. In
solutions of pH 12, a phase maximum at a frequency of 1 Hz was observed. To be sure that
there was no second time constant at lower frequencies, impedance measurements down to
frequencies of 1 MHz were taken. A typical example of these measurements for solutions of
pH 12 is presented in Fig. 5. The behavior of the electrode in basic solutions is very similar
to an ideally corroding system with a single time constant corresponding to the corrosion
reaction rate determining step. This behavior can be simulated by a simple equivalent circuit
model of the Randles type which consists of a parallel combination of a resistor, RP ,
representing the polarization or charge transfer resistance and a capacitor, C , representing the
capacitance of the electrode/electrolyte interface. This parallel combination is in series to a
small resistor, Rs , equivalent to the electrolyte resistance.
The data in Fig. 5 were subjected to a procedure of data fitting [31] to fit the
experimental data in this figure to the electronic model described. Good agreement was
obtained between the experimental and theoretical data for values of RP = 10.22 k, C =
-2
170.4 F cm , and Rs = 42 . The fitting procedure for the results of solutions of pH of 12
389
Fundamental Aspects
had around 2% mean error in the absolute impedance and 1.2 mean error in the phase
angle. Deviations of the phase angle from ideal behavior were found to be related to the
polishing of the electrodes surface. The impedance data presented show that the vanadium
electrode, although it showed active dissolution, it had a great tendency towards oxygen and
the surface was covered with a thin film of non-stoichiometric oxide or a mixture of oxides of
varying valences. The instability of such oxides explain the corrodibility of vanadiums
surface. The increased rate of corrosion with increases in the pH of the solution was varied
by measuring the corrosion currents and polarization resistance in each solution. The values
of these parameters in pHs 2, 7 and 12, are presented in Table 1.
RP
2
(kcm )
5.012
2.880
1.652
icorr
-2
(Acm )
0.407
1.239
3.930
Ecorr
(mV)
-215
-407
-597
The effect of the prevailing gas on the impedance behavior of the vanadium electrode
was also investigated. An example of these measurements in solutions of pH 12 is presented
in Fig. 6. After 3 hrs of electrode immersion, the impedance behavior in H2 or N2 saturated
solutions is quite similar. In air or oxygen-saturated solutions, the measured polarization
resistance is lower. Polarization measurements have shown that the corrosion current
390
Badawy et al.
decreases in the presence of an inert gas in basic solutions. In acidic solutions, on the other
hand, the corrosion rate is not much affected by the inert gases. These results are summarized
in Table 2. The results of polarization experiments are in good agreement with the
+
explanation based on Eqs. 6 and 7. In acidic solutions, the interaction of the excess H ions
with the surface film leads to the removal of this film without any appreciable change in the
rate of corrosion of the metal by changing the gas. In basic solutions, the formation of the
non-stoichiometric, unstable, basic oxides is responsible for the increased rate of corrosion of
the metal. The formation of the oxide film and its stoichiometry is dependent of the presence
of air or O2 in the solution. Removal of air or oxygen from a basic solution shifts the
equilibrium of Eq. 5 to the left, and hence, decreases the rate of corrosion as can be seen from
the values of the corrosion currents presented in Table 2. The presence of the surface film is
confirmed by capacitance measurements. In all solutions, the electrode capacitance showed
an approximately constant value within a wide potential range (-100 - +100 mV from the
-2
steady-state potential). In acidic solutions, an average capacitance value of 25 Fcm was
measured. This value is higher than the reported value of the Helmholtz capacitance (17
-2
Fcm ) [32]. The higher capacitance value can be attributed to the presence of adsorbed
electroactive species on the surface film. The concentration of these electroactive species at
the electrodes surface is constant in the potential range where the electrode capacitance is
potential-independent.
Figure 6. Effect of the prevailing gas on the impedance characteristics of the vanadium
electrode in solutions of pH 12
(- -) oxygen, () nitrogen, (----) naturally aerated, (....) hydrogen
Table 2. Corrosion Currents of Vanadium in Solutions of pHs 2, 7 and 12 Saturated with
Different Gases
Gas
-2
icorr (A-cm )
Rp (kcm )
391
Fundamental Aspects
Air
Oxygen
Nitrogen
Hydrogen
pH 2
0.407
1.057
1.578
1.046
pH 7
1.239
2.939
1.967
1.082
pH 12
3.930
17.50
1.710
0.928
pH 12
1.652
1.596
2.352
2.072
(10)
(11)
a is the energy relative to the ground state energy which an atom or molecule must have in
order to react, i.e., the activation energy per molecule, whereas Ea is the molar activation
energy. Figure 7 presents the Arrhenius plots obtained in solutions of pH 2, 7 and 12.
In the solutions investigated, almost parallel Arrhenius plots were obtained, which means
that the activation energy of the corrosion process lies in the same range without regard to the
solutions pH. Calculation of the activation energy of the corrosion process in each solution
gave the values presented in Table 3. The values given in Table 3 show that the activation
-1
energy of the corrosion process is less than 40 kJmol , which supports the view that the
dissolution of the metal is a one-electron charge transfer process [34]. This supports the
mechanism suggested by Armstrong and Henderson [14], and the corrosion reaction may be
presented by
V(s)
V(I) + e
2+
(12)
+
VO +2H +3e
This reaction is enhanced in basic media, and hence, the rate of corrosion increases. In
accordance with this, the calculated activation energy in solutions of pH 12 is slightly lower.
Badawy et al.
Corrosion of Vanadium in
Naturally Aerated Solutions of
pHs 2, 7, and 12
pH
2
7
12
-1
W.J. Tomlinson, R. Rushton, R. Cindery and S. Palmer; J. Less Common Met. 132,
1987, p. 1.
2. E. Sum and M. Skyllas-Kazacos, J. Power Sources 15, 1985, p. 179.
3. E. Sum, M. Rychcik and M. Skyllas-Kazacos, J. Power Sources 16, 1985, p. 35.
4. M. Rychcik and M. Skyllas-Kazacos, J. Power Sources 19, 45, 1987, p. 45.
5. M. Kazacas and M. Skyllas-Kazacos, J. Electrochem. Soc. 136, 1989, p. 2759
6. T. Hurlen and W. Wilhelmsen, Electrochim. Acta 31, 1986, p. 1139.
7. W.Wilhelmsen and T. Hurlen, Electrochim. Acta 32, 1987, p. 85.
8. S. Hornkjol, Electrochim. Acta 33, 1988, p. 337.
9. W.A. Badawy, J. Appl. Electrochem. 20, 139, 1990, p. 139.
10. W.A. Badawy and K.M. Ismail; Electrochim. Acta 38, 1993, p. 2231.
11. W. Muthman and F. Fraunberger, Sitzbl. Bayr. Akad. Wiss., 1904, p. 201.
12. G.C. Schmidt, Z. Phys. Chem. 106, 1923, p. 105.
393
Fundamental Aspects
13. R. Kammel, T.Kishi, T.Takei and H. Winterhager, Metalloberflaesche 24, 1970, p. 335.
14. R.D. Armstrong and M. Henderson, J. Electroanal. Chem. 26, 1980, 381.
15. S. Homkjol and I.M. Homkjol, Electrochim. Acta 36, 1991, p. 571.
16. A. Deschanvers and G. Nouet, Bull. Soc. Chim. Fr. 718, 1975, p. 1589.
17. A.G. Keil and R.E. Salomon, J. Electrochem. Soc. 112, 643, 1965, p. 643 and 115, 1968,
p. 628.
18. A.G. Keil and R.E. Salomon, J. Electrochem. Soc. 115, 1968, p. 628.
19. R.G. Keil and K. Ludwig, J. Electrochem. Soc. 118, 864, 1971, p. 864.
20. G.D. Fasman, Practical Handbook of Biochemistry and Molecular Biology, CRC Press
Inc., Boca Raton, Florida, 1989.
21. F.M. AI-Kharafi and W.A. Badawy, Electrochim. Acta 40, 1995, p. 2623.
22. A. Belanger and K. Vijh Ashok, J. Electrochem. Soc. 121, 225,1974, p. 225.
23. P.W. Atkins, Physical Chemistry, 5th Ed., Oxford University Press, Oxford, 1994.
24. W.A. Badawy, A. Felske and W.J. Plieth, Electrochim. Acta 34, 1989, p. 1771.
25. M. Pourbaix Atlas of Electrochemical Equilibria in Aqueous Solutions, Pergamon Press,
London, UK, 1966, pp. 234-245.
26. A.J. Brock and G.C.Wood, Electrochim. Acta 12, 395, 1967, p. 395.
27. D.D. Macdonald, S. Real, S.I. Smedley and M. Uraquidi-Macdonald; J. Electrochem. Soc.
135, 2410, 1988, p. 2410.
28. C.M.A. Brett, Corros. Sci. 33, 1992, p. 203.
29. K. Juttner, W.J. Lorenz, M.W. Kendig and F. Mansfeld, J. Electrochem. Soc. 135, 1988,
p. 322.
30. K. Juttner, Electrochim. Acta 35, 1990, p. 1501.
31. W.A. Badawy, S.S. El-Egamy and K.M. Ismail, British Corros. J 28, 1993, p. 133.
32. J.O.M. Bockris and A.K.N. Reddy, Modern Electrochemistry, 2nd ed., Chap. 7, Plenum
Press, New York, USA, 1977.
33. R.G. Martimer, Physical Chemistry, The Benjamin/Cummings Publishing Company Inc.,
Redwood City, California, USA, 1993.
34. G.A. Wright, J. Electrochem. Soc. 114, 1967, p. 1263.
394
ABSTRACT
The effect of monochromatic ultraviolet (UV) light on the passive films formed on Types 304
and 316 stainless steels (SS) is described. Under UV irradiation 304SS and 316SS specimens, in
neutral and acidic solutions, exhibited an increased resistance to localized corrosion (pitting). This
resistance to localized corrosion was gauged by an increase in induction time, an increase in
breakdown potential, and some significant changes in the current noise at constant potentials. All
these changes indicate that shining UV light on a metal specimen can sometimes decrease its
susceptibility to pitting.
It was observed that the extent of photoinhibition of localized attack (PILA) depends on the
nature of the passive film, the period of illumination, and the incident photon energy. It was also
observed that the PILA effect can, in some cases, last for over 200 hours after the illumination has
been removed. Increased pitting resistance was observed with higher energy incident photons. The
minimum apparent incident photon energy corresponds to the band gap of the metal specimen (375
nm for SS). The optimum illumination period observed in these experiments was approximately 5
hours. In alkaline solutions a much decreased PILA effect was observed, this decrease in PILA was
attributed to the formation of a precipitate layer. This precipitate layer in turn interfered with the
incident photon interaction with the barrier layer. Finally, a possible explanation of PILA is given
within the framework of the Point Defect Model (PDM).
Key Words: Photoinhibition, stainless steel, localized corrosion, pitting, UV, PDM, passive films
INTRODUCTION
The initiation and propagation of pits and the corresponding breakdown of the passive
film that forms on metals and alloys is of great fundamental interest in electrochemistry and
corrosion science. Numerous efforts, ranging from the addition of inhibitors [1] to the
alloying of base metals [2-5], have been made in an attempt to prolong the effective life of the
passive film. Recently, it has been shown that irradiating immersed electrodes with
ultraviolet (UV) light can inhibit localized corrosion. The first observation of this kind was
made when polycrystalline nickel, in chloride-containing solution, was irradiated with white
light [6]. Other observations supporting photoinhibition of localized attack (PILA) include
similar effects on 304 stainless steel (SS) [7] and even pure iron under UV irradiation [8-9].
The purpose of this study is to examine the effects of UV irradiation on the photoinhibition of
304SS and 316SS in chloride-containing solutions. These results could help shed light on
395
Fundamental Aspects
how PILA affects SSs and lay the groundwork for photoinhibition as a new form of corrosion
control.
EXPERIMENTAL PROCEDURE
Test specimens were prepared from Types 304 and 316 SS rods, which were covered
with lacquer, mounted in a PVC holder and then embedded in a two-component epoxy resin.
The exposed surface, approximately 0.8 cm2 in area, was polished mechanically with
successively finer grades of SiC paper and 0.05 alumina powder to a mirror finish. The
chemical composition of the SS samples used is shown clearly in Table 1.
Table 1. Chemical Composition of 304 SS and 316 SS (in Wt %)
SS Type
C
304
0.08
316
0.08
Mn
2
2
Cr
18
16
Ni
8
12
P
S
0.04 0.003
0.04 0.003
Si
1
1
Mo
Trace
2
Fe
Bal.
Bal.
The electrochemical cell consisted of a three-electrode PTFE cell equipped with a quartz
window to allow irradiation of test electrodes. A saturated calomel electrode (SCE) was used
as the reference electrode, and a platinum wire, coiled inside the cell, was used as the
auxilliary electrode. All test solutions were prepared from Analar-grade reagents and
deionized water, and were deoxygenated with nitrogen. The pH of the solution was adjusted
to 7.5 with NaOH, or alternatively, buffered to pH 7.5 with a 0.15 mol dm-3 H3BO3/0.007 mol
dm-3 Na2B4O7 solution.
B
The working electrodes were irradiated at wavelengths between 300 and 425 nm using a
150 W UV-enhanced Xe lamp (Oriel Model 6254) and a 1/8 monochromator (Oriel Model
77250). The incident power density at 300 nm was 0.4 mW cm-2, giving a photon flux of
6.04 x 1014 cm-2. The photon flux was maintained at approximately this value at each
wavelength by adjusting the light intensity at the surface.
Electrochemical tests were carried out using a Solartron/Schlumberger Electrochemical
Interface (Model 1286). In potentiodynamic polarization tests, the working electrodes were
polarized at a rate of 0.1 mV s-1 in the anodic direction up to the breakdown potential. In
illumination experiments, the electrodes were illuminated continuously throughout the
potential scan. The breakdown potential was recorded as the potential at which the current
exceeded 80 A cm-2. In current-time measurements, the electrodes were initially polarized
at a potential in the passive region for a 30-minute period, and then the potential was stepped
to an appropriate point where metastable pitting could be observed for the non-illuminated
specimens. The current transients were then recorded as a function of time, using a Keithley
Model 576 data acquisition unit at a sampling rate of 90 mS.
Additional experiments involved polarizing the working electrodes, under illumination
for periods of up to 15 hours, and then determining the breakdown potential using the
potentiodynamic polarization method. The exact same polarization periods were used for the
illuminated and non-illuminated electrodes.
396
Al-Rifaie et al.
Figure 1. Potentiodynamic polarization curves for type 304 SS in neutral 0.5 mol dm-3 NaCl
under: (a) non-illumination; and (b) illumination at 300 nm
The effect of illumination on the breakdown potentials of 304 SS and 316 SS can
perhaps be seen more clearly from the data shown in Table 2, which shows averages of the
breakdown potentials for 304 SS and 316 SS as a function of chloride concentration. In each
case, an average increase of about 60 40 mV in the breakdown potential can be observed
upon illumination. Another observation that can be made from the data is that the breakdown
potentials of the illuminated 304 SS specimens approach those of the 316 SS specimens in the
dark. This observation could suggest a comparable degree of passivity enhancement between
alloying and illumination under these conditions.
An even greater increase in the breakdown potential, approximately 150 50 mV, was
observed on prior illumination of the specimens at 300 nm for periods exceeding 5 hours. In
these experiments, the electrodes were polarized in a 0.1 mol dm-3, NaCl buffered solution at
+250 mV (SCE) for various periods of time under illumination and non-illumination. The
specimens were then polarized from +250 mV (SCE) in the anodic direction at a rate of 0.1
397
Fundamental Aspects
mV s-1 up to the breakdown potential. The displacement in the breakdown potential was
calculated by subtracting the average breakdown potential for the specimens polarized in the
dark from the average breakdown potential for the specimens polarized in the light. Each
experiment was repeated three times. This data are shown graphically in Fig. 2, where the
average displacement in the breakdown potential, Eb is shown as a function of the prior
illumination period.
Table 2. Breakdown Potential Values for 304 SS and 316 SS Under Light and Dark
Conditions
[Cl-] mol dm-3 304 SS Eb (dark) 304 SS Eb (light) 316 SS Eb (dark) 316 SS Eb (light)
0.025
355 7 mV (3)
420 10 mV (3)
430 10 mV (3)
490 11 mV (4)
0.5
275 18 mV (20) 350 20 mV (22) 330 20 mV (17) 395 20 mV (17)
2.0
160 8 mV (4)
210 15 mV (5)
230 12 mV (5)
290 10 mV (4)
Eb in mV vs. SCE
Light = 300 nm
The numbers in parentheses indicate the number of times the experiment was repeated
398
Al-Rifaie et al.
Further evidence for photoinhibition of pitting attack was obtained from current-time
measurements where the current decay transients were monitored as a function of time for
illuminated (300 nm) and non-illuminated 316 SS. These data are shown in Fig. 3.
It is evident from Fig. 3 that illumination causes a delay in the onset of metastable
pitting, even after approximately 110 minutes, the illuminated film was still able to
repassivate while the dark film had started breaking up after only 25 minutes. Therefore,
illumination seemed to postpone metastable pitting by at least a factor of 3, which in itself is
quite astounding.
One of the questions that this study aims to answer is how prior illumination affects the
passive film on 304 SS and 316SS. In order to quantify the permanent nature of the
photoinhibition effect, the pitting susceptibility of 316SS was studied at various periods of
time with prior illumination. The specimens were illuminated at 300 nm for 80 minutes under
polarizing conditions in a neutral 0.5 mol dm-3 NaCl solution. The specimens were then
immersed under open-circuit conditions (dark) in a borate buffer solution (pH of 7.5), and
removed at selected intervals. The breakdown potential was determined in a neutral 0.5 mol
dm-3 NaCl solution using the potential scan method. Identical experiments were carried out
in the dark; the specimens were polarized in the chloride solution (dark) for 80 minutes,
removed and immersed in the borate solution. The breakdown potential was determined at
selected intervals. Data collected in this manner for periods up to 350 hours are shown in Fig.
4, where the breakdown potential is plotted against the immersion period following
illumination or polarization.
399
Fundamental Aspects
Figure 3. Current-time decay profiles for 316 SS polarized at 285 mV (SCE) in a neutral
0.025 mol dm-3 NaCl solution under: (a) dark, and (b) light (300 nm) conditions
Figure 4. Breakdown potential of illuminated and non-illuminated 316SS in 0.5 mol dm-3
NaCl as a function of the immersion period in a borate buffer solution (dark)
following polarization or polarization and illumination at 300 nm.
(a) on a linear scale; and (b) on a semi-log scale
A clear difference between the breakdown potentials measured for the illuminated and
non-illuminated specimens can be seen for immersion periods up to about 220 hours,
indicating that the photoinhibition effect persists over this period of time. The gradual
increase in breakdown potential (i.e., a shift towards the more noble direction) may be
attributed to a crystallization process or chromium-enrichment in the passive film. A similar
trend was observed for 304SS.
The influence of solution pH, and thus the nature of the passive film, on the extent of
photoinhibition was studied by polarizing and illuminating the electrodes in solutions of
varying acidity. A 0.5 mol dm-3 NaCl solution was used as the test solution; the pH was
adjusted to the desired value by the addition of NaOH or HCl. All irradiation experiments
were carried out at 300 nm. The breakdown potentials were determined from polarization
measurements for specimens polarized in the dark and under conditions of continuous
400
Al-Rifaie et al.
illumination. Each experiment was carried out at least three times. The displacement in the
breakdown potential, Eb, was calculated as the difference between the light and dark
breakdown potentials. The average displacements in the breakdown potentials for 304SS and
316SS are shown as a function of pH in Fig. 5; the degree of scatter in the average
displacements was 30 mV. An essentially constant increase in the breakdown potentials, of
approximately 60 mV, was observed on illumination, except for those specimens polarized in
the alkaline solutions, where no apparent photoinhibition effect was detected. However, it
was found that the photoinhibition effect was partially restored under these alkaline
conditions (pH of 10) by the addition of a 0.01 mol dm-3 EDTA solution to the test solution.
The pH in this region was adjusted with NaOH and maintained at 10 on addition of the
complexing EDTA agent. The average displacements in the breakdown potentials for both
304SS and 316SS at a pH of 10 on addition of the EDTA were 45 and 50 mV, respectively.
The presence of EDTA at other pH values did not enhance the photoinhibition effect. This
seems to suggest that the precipitated layers formed in alkaline environments are photoelectrochemically inactive, but that the addition of a chelating agent hinders the formation of
this layer, allowing the photons to reach the barrier layer.
Figure 5. Displacement in the breakdown potential, Eb, as a function of the pH of a 0.5 mol
dm3 NaCl solution, on illumination of: (a) 304SS; and (b) 316SS at 300 nm
401
Fundamental Aspects
The effects of variations in the photon energy on the breakdown potential displacement
(a measure of photoinhibition) are shown graphically in Fig. 6. A constant photon flux was
maintained at each wavelength. A neutral 0.5 mol dm-3 NaCl solution was used as the test
solution. A total of twenty experiments were carried out for each of the SSs under conditions
of non-illumination in order to obtain adequate reference breakdown potentials. The amount
of scatter in the breakdown potentials, under these conditions, was on the order of 20 mV.
The mean value of the breakdown potential calculated for 304SS in the dark was 272 mV
(SCE), while that for 316SS in the dark was 327 mV (SCE). Displacements in the breakdown
potential, Eb, on illumination were calculated as the difference between the breakdown
potentials in the light and the dark. It can be seen from Fig. 6 that the degree of
photoinhibition depended on the photon energy, with the photoinhibition effect decreasing
with wavelengths exceeding 375nm.
Figure 6. Displacement in the breakdown potential, Eb, measured in a 0.5 mol dm-3 NaCl
solution, as a function of the incident light wavelength on illumination of: (a)
304SS; and (b) 316SS
The induction periods for 316SS specimens polarized at +285 mV (SCE) in a 0.025 mol
dm NaCl solution can be plotted as a function of varying photon energy as shown in Fig. 7.
Figure 7 also shows the induction periods measured for identical experiments carried out in
the dark. These data points are plotted at each wavelength so that the increase in the
induction period on illumination is evident. The induction periods were measured as the time
-3
402
Al-Rifaie et al.
between the application of the polarizing potential and the first metastable pitting events in
which the current exceeded 500 nA. It is clear from this figure that the induction time was
reduced slightly with decreasing photon energy.
Figure 7. Measured induction periods as a function of the incident light wavelength for
316SS polarized at +285 mV (SCE) in 0.025 mol dm-3 NaCl. Induction periods
for non-illuminated specimens are also shown for reference (i.e., dark triangles at
each wavelength)
In previous papers [6,7], PILA has been interpreted using the PDM for the growth and
breakdown of passive films [10] as the photo-quenching of the electric field within the barrier
layer. The PDM has already been developed to give theoretical expressions for the
breakdown potential, Eb, and the induction time, tind. It is proposed that on illumination,
incident photons (with energies in excess of the band gap of the metal) generate electron-hole
pairs that are separated by a steep potential gradient in a manner which quenches the electric
field. Once the electric field is decreased, the theoretical expressions predict a higher
breakdown potential and a larger induction time. Therefore, Figs. 1-7 are indeed consistent
with a PDM interpretation of the photoinhibition effect since they predict that incident photon
energy increases pitting resistance. It is not clear, at least from the experimental evidence
shown here, how the electric field itself is quenched.
The data presented in Fig. 5 suggests that the formation of a precipitate layer on the
metal specimens polarized in the alkaline solutions screens the barrier layer from the incident
403
Fundamental Aspects
photons, and thus inhibits the generation of electron-hole pairs (and subsequent quenching of
the electric field). This is supported by the experiments in which the PILA effect was
partially restored on addition of the complexing agent, EDTA. This complexing agent may
hinder the formation of the precipitate layer, and hence, facilitate the photon-barrier layer
interaction. Also, the fact that the PILA effect remains unaffected (in neutral and acidic
solutions), or increases (in alkaline solutions), in the presence of EDTA suggests that it is
unlikely that photo-induced reactions, involving oxidized iron, at the film/solution interface
account for the photoinhibition effect.
The semipermanent nature of PILA is evident in this study (as shown in Figs. 4 and 7)
and other studies [8,9]. The PILA effect remaining after the irradiation has been removed
seems to indicate that the photoinhibition effect cannot be explained solely by the changing of
the electronic structure of the film. Consequently, it is postulated that the suppression of the
electric field strength also modifies the vacancy distribution. If we assume that the thickness
of the barrier layer (L) is 3 nm, and the cation vacancy diffusivity is on the order of 10-19
cm2s-1 [12], we can calculate an approximate relaxation time (t=L2/D). The relaxation time of
the vacancy structure is thus estimated to be around 9 x 105 s. If we then compare this value
with the period of 220 hours (7.92 x 105 s, from Fig. 4), there is good agreement between the
two values, suggesting that the photoinhibition effect persists until the vacancy structure
relaxes. Figure 2 also supports this idea in the sense that longer illumination periods lead to
an increased PILA effect by altering the vacancy structure more dramatically, and therefore,
requiring a larger relaxation time with increasing illumination time. Another possible
explanation of PILA is that the UV irradiation leads to a chromium enrichment of the passive
film. Since the PILA effect on pure iron [8,9] and nickel [6] cannot be explained by
chromium enrichment of the passive film; a more likely possibility is one in which both the
electric field is quenched and the passive film is enriched in chromium simultaneously.
CONCLUSIONS
The results of this work show that photoinhibition of pitting corrosion can be achieved
for SSs on illumination with UV light. Increases in both the breakdown potential and
induction period, and a decrease in the frequency of metastable pitting events were observed
upon irradiation. It was also found that this PILA effect depended on the photon energy (with
photons having energies above the band gap of the specimen being more effective), the
illumination period, the pH of the test solution, and the nature of the resulting passive film.
It appeared that the precipitate layer formed on passivation of 304SS and 316SS in
alkaline solutions (pH > 10) adversely affected the interaction of the incident photons with
the barrier layer. The addition of EDTA, a complexing agent, partially restored the PILA
effect, which seems to support the hypothesis that the precipitate layer is indeed hindering the
photon-barrier layer interaction. These observations can be explained within the framework
of the PDM in terms of the generation of electron-hole pairs and consequent photo-quenching
of the electric field. This in turn modifies the vacancy structure, leading to an enhancement
in the pitting resistance of the specimens, that remains effective for some 220 hours.
ACKNOWLEDGEMENT
404
Al-Rifaie et al.
The authors gratefully acknowledge the support of this work by the Electric Power
Research Institute under Contract No. RP8041-07, and by the US Department of
Energy/Basic Sciences Division through Grant No. DE-FG02-91ER45461.
REFERENCES
1. M. Ohi, H. Nishihara and K. Aramaki, Corrosion 50, 1994, p. 226.
2. R.G. Wendt, W.C. Moshier, B. Shaw, P. Miller and D.L. Olson, Corrosion 50, 1994, p.
819.
3. B.A. Shaw, G.D. Davis, T.L. Fritz, B.J. Rees and W.C. Moshier, Journal of the
Electrochemical Society 138, 1991, p. 3288.
4. A.J. Sedriks, Corrosion of Stainless Steels, The Electrochemical Society, Princeton, New
Jersey, 1979.
5. P.M. Natishan, E. McCafferty and G.K. Hubler, Journal of the Electrochemical Society
135, 1988, p. 321.
6. S.J. Lenhart, M. Urquidi-Macdonald and D.D. Macdonald, Electrochimical Acta 32,
1987, p. 1739.
7. E. Sikora, M.W. Balmas, D.D. Macdonald and R.C. Alkira, Corrosion Science, in press.
8. P. Schmuki and H. Bohni, Journal of the Electrochemical Society 139, 1992, p. 1908.
9. P. Schmuki and H. Bohni, Electrochimical Acta 40, 1995, p. 775.
10. D.D. Macdonald, Journal of the Electrochemical Society 139, 1992, p. 3434.
405
ABSTRACT
The kinetics of corrosion of a low Cr-Mo steel alloy were studied over a temperature range of 75250 C in 1 m NaCl in the absence and in presence of various levels of contamination with CuCl2. We
measured corrosion rates, weights of corrosion product (magnetite) film and total (integral) weight
loss of the alloy over exposure times of 1-480 hours. The corrosion rate decreased rapidly with time,
before it leveled off at longer time periods, indicating the formation of a protective corrosion product
film. The ability of the alloy to retain an adherent corrosion product (magnetite) film was expressed in
terms of a retention coefficient. This increased with temperature and exposure time, and decreased
with the level of contamination with CuCl2. The effect of temperature was attributed to the
improvement of the crystallinity of the corrosion product. On the other hand, the effect of the CuCl2
was attributed to the electro-deposition of Cu and its impregnation within the corrosion product, which
became less adherent. The free corrosion potential was affected by the presence of the CuCl2 in a
fashion compatible with the Wagner-Traud theory of mixed potential.
0
Key Words: Kinetics, corrosion, steel, high temperature, sodium chloride solution, copper chloride.
INTRODUCTION
The corrosion of steel in high temperature aqueous environments is encountered in many
industrial applications, e.g., boiling water reactors [1], desalination plants [2], high
temperature aqueous fuel cells [3], and steam generators [4]. In such environments,
contaminants, which are present in the aqueous media at trace levels, are concentrated by
several orders of magnitude to form highly corrosive solutions [5]. Due to the active nature
of iron, it corrodes in high temperature deaerated water and steam giving rise to the formation
of ferrous (Fe2+) species which change to ferrous hydroxide, Fe(OH)2, and magnetite, Fe3O4
[6-10]: i.e.,
3 Fe + 6 H2O = 3Fe(OH)2 + 3 H2
(1)
(2)
(3)
407
Fundamental Aspects
Some of the resulting magnetite adheres to the surface in the form of a film which affects the
kinetics of any subsequent corrosion of the steel. The rest of the resulting magnetite spalls off
the surface into the electrolyte. The qualities of the adherent magnetite film depend on the
temperature, composition of the environment and exposure time.
The objectives of this paper are to study the kinetics of corrosion of a low Cr-Mo steel in
high temperature NaCl solution, and the mechanism of protective film formation during this
process. Particular attention is given to the effect of contamination of the electrolyte with
CuCl2 on the integrity of the protective film, and hence, on the subsequent corrosion. The
effects of CuCl2 concentration, temperature and exposure time on the adherence of the
magnetite film were also determined.
EXPERIMENTAL PROCEDURE
All measurements were performed in an autoclave fabricated from 316 type stainless
steel. The autoclave consisted of two parts. A (Teflon) PTFE cell was machined to fit tightly
into the autoclave, to accommodate the electrolyte. Further details are given elsewhere [11].
The cell was preheated for about 5 hours to obtain thermal stability [12,13]. The autoclave
was placed in a furnace connected with the temperature regulator to the heating source. A NiCr thermocouple was used to regulate the temperature. It was inserted into a stainless steel
tube coated with a layer of PTFE. The corrosion rate measurements were taken on coupons
(2 x 5 x 0.2 cm) made of a low Cr-Mo steel of the following composition (wt%): 2.3 Cr; 1.0
Mo, 0.46 Mn, 0.2 Si, 0.13 C, 0.015 P, 0.007 S and Fe balance. They were annealed at 900oC
for 1 hour in an argon atmosphere and furnace-cooled. Their microstructure revealed fine
dispersed carbide in a matrix of ferrite. Before use, they were polished successively down to
600 grit using silicon carbide paper, rinsed with ethyl alcohol and distilled water, and then
dried in the air. Three electrolytes were used: (I) 1 molal (m) NaCl, (II) 0.999 m NaCl + 5 x
10-4 m CuCl2 and (III) 0.9 m NaCl + 5 x 10-2 m CuCl2. They were deaerated by boiling the
electrolyte under reflux for 15 miutes to give an oxygen content of < 0.1 ppm (as estimated
polarographically). The volume of the electrolyte in each test was 200 ml. The tests lasted
for various durations, i.e., 1, 3, 6, 12, 24, 48, 96 and 480 hours and were performed in
triplicate. Two of the three specimens were subjected to successive descaling by immersing
for 20 minutes in a 20% ammonium citrate solution at 80oC [14] to dissolve the corrosion
products. They were then rinsed with distilled water, dried and weighed until a constant
weight was obtained. We calculated the integral weight (Wi ) i.e., the weight of the alloy
which dissolved up to a particular time, and the weight of the corrosion product film (Wf )
which remained adherent per square centimeter of the area after a particular time. After each
test, the solution was found to contain some solid (spalled) corrosion products.
The working electrode consisted of a rectangular sheet about 9 cm long, 0.5 cm wide
and 0.2 cm thick. It was insulated with PTFE in such a way that an area of 1 cm2 was
exposed at its end. The other end was threaded and connected to a stainless steel rod of 0.3
cm diameter through a stainless steel connector. A graphite rod of 0.5 cm diameter and about
10 cm length was used as a counter electrode, and an Ag/AgCl was used as a reference
electrode [12,15].
RESULTS AND DISCUSSION
408
Ghanem et al.
Corrosion Rate
Figure 1 (a-c) illustrates the variation of the corrosion rate with time of immersion at
various temperatures in electrolyte I, electrolyte II and electrolyte III. Figure 1d compares the
behavior in the three electrolytes at 2500C. They clearly reveal same significant features.
During short time periods, the corrosion rate decreased rapidly with the time of immersion
before it tended to level off after longer time periods. This behavior is characteristic of
protective film formation [16]. There was a strong detrimental effect of CuCl2 on the ability
of the magnetite film to protect the substrate alloy. As the temperature and/or exposure time
increased, the corrosion rate decreased.
The present work reveals that the mechanism of corrosion changes after a transition time,
, the magnitude of which, generally, decreases as the temperature of the test increases. At
and beyond this transition time, an adherent layer of the corrosion product was shown to
protect the substrate alloy by acting as a diffusion barrier [11,17], thus reducing the rate of
corrosion. Before this transition time, the alloy corrodes more freely with a higher rate of
corrosion. It was found that, at a given temperature, increasing the concentration of CuCl2
increased the transition time, [17].
Retention Coefficient
The retention coefficient is introduced here to give a quantitative expression of the
ability of the alloy to retain an adherent corrosion product film on its surface under a
corrosive environment. It is defined as the ratio of the weight of the adherent (magnetite)
film, Wf (adh.), at a particular time of immersion to the total weight of the (magnetite) film
which would form if the integral weight loss of the alloy were to be totally consumed in
forming the film material (magnetite), i.e., Wf (total). The later value is related to the integral
weight loss Wi by a chemical factor (CF), which in the present case is given by the ratio of
the molecular weights of Fe3O4 and 3 Fe i.e., CF = 232/168 = 1.38. Thus, the retention
coefficient is given by
Retention coefficient = Wf (adh.) /Wf
(total)
(4)
The retention coefficient was determined at various temperatures, CuCl2 concentrations and
time intervals. Figure 2 (a-d) illustrates the variation of the retention coefficient, , with the
time of immersion for the three electrolytes at various temperatures. The curves clearly
reveal that increased as the temperature increased, and decreased as the concentration of
CuCl2 increased. Reaction 2, which is called the Schikorr reaction [18], has been extensively
studied [19,20]. Ferrous hydroxide, Fe(OH)2, decomposes rapidly above 1000C [21] , but
relatively slowly at lower temperatures. Robertson [22] stated that the corrosion of steel in
hot water is controlled by the dehydration of the hydroxide phase (Eq. 2), which proceeds
when the metal/solution interface becomes saturated with Fe(OH)2. Consequently, two
factors affecting reaction 2,
The temperature, which enhances the reaction in the forward direction and
affects the solubility [23] and crystallinity of the magnetite film [17].
409
Fundamental Aspects
This explains the higher values obtained at higher temperatures, that longer exposure times,
and hence, the increased efficiency of the film in retarding corrosion. On the other hand, the
presence of CuCl2 in the electrolyte decreased . This has previously been shown [17] by xray diffraction and scanning electron microscopy to be due to the electro-deposition of Cu
and its impregnation within the magnetite film, which then becomes less adherent.
410
Ghanem et al.
Cu
(5)
(6)
The values of E0 were obtained from Latimer [24]; the activity of the Cu2+ species was taken
equal to its concentration. The values of E (H2O/H2) at different temperatures were taken
from Pourbaix diagrams [6, 25,26].
Consequently, under the potentials shown in Fig. 4, the cathodic half cell reaction
involves both the reduction of water i.e., reaction 7
2 H2O + 2 e
H2 + 2 OH-
(7)
and the electro-deposition of Cu according to reaction 5, while the anodic reaction involves
the dissolution of the iron, i.e., reaction 8
Fe + H2O
Fe(OH)+ + H+ + 2e
(8)
Since the concentration of Cu2+ is rather small in electrolyte II, the time behavior of Ecor is not
significantly different from that in electrolyte I at the higher temperatures i.e., 125, 175 and
411
Fundamental Aspects
412
Ghanem et al.
Figure 3. Time variation of the free corrosion potential for the alloy at
different temperatures in: electrolyte I (1 m NaCl); II (0.999 m NaCl +
0.0005 m CuCl2), and III (0.9 m NaCl + 0.05 m CuCl2)
Table 1. Approximate Values of the Electrode Potential, V (NHE) of the Cu/Cu2+
Calculated at Various Temperatures Using the Nernst Equation in
Electrolytes II and III and of the H2O/H2 Systems in Electrolytes I, II and
III [6, 25,26]
Temperature
750C
1250C
1750C
2500C
Electrolyte I
H2O/H+
- 0.442
- 0.551
Electrolyte II
Cu/Cu2+
H2O/H+
+ 0.312
- 0.405
+ 0.309
+ 0.305
+ 0.299
- 0.484
Electrolyte III
Cu/Cu2+
H2O/H+
+ 0.329
- 0.361
+ 0.327
+ 0.326
+ 0.325
- 0.415
413
Fundamental Aspects
1.
At short times, the corrosion rate decreases rapidly with the time of immersion before
it tends to level off at longer times. This behavior is characteristic of protective film
formation
2.
The retention coefficient is introduced to give a quantitative expression for the ability
of the alloy to produce an adherent corrosion product film under the corrosive
environment. Increasing the temperature enhances the ability of the alloys surface
to retain the film. The concentration of CuCl2 has an opposite effect.
3.
The results of potential-time curves measured in different electrolytes reveal that Ecor
shifts in the noble direction to an extent that increases with the concentration of
CuCl2. This is compatible with the Wagner-Traud theory of mixed potential. The
increase in temperature above 750C shifts the values of Ecor in electrolyte I and II
closer to each other than they are at 750C.
ACKNOWLEDGMENT
The authors express their warm gratitude to Prof. A.A. Abdul Azim, the former chairman
of CMRDI, for valuable discussions.
REFERENCES
1. B.C. Syrett, Materials Performance 30, 8, 1992, p. 52.
2. O. Osborn and F.H. Coley, in High Temperature High Pressure Electrochemistry in
Aqueous Solutions, Houston, NACE 4, 1976, p. 7.
3. F.T. Bacon, in High Temperature High Pressure Electrochemistry in Aqueous
Solutions, Houston, NACE 4, 1976, p. 24
4. M.J. Wootten, G. Economy, A.R. Pebler and W.T. Linsay. Jr., Materials Performance
17, 2, 1978, p.30.
5. C.B. Ashmore, M.H. Hurdus, A.P. Mead, P.J B. Silver, L.Tomlinson and D.J.
Finnigan, Corrosion 44, 1988, p. 334.
6. M. Pourbaix, in Atlas of Electrochemical Equilibria in Aqueous Solutions, London,
Pergamon Press, 1974, p. 305.
7. J.E. Castle and G.M.W. Mann, Corrosion Science 6, 1966, p. 253.
8. J. Robertson, Corrosion Science 29, 1989, p. 1275.
9. J. Jelinek, P. Neufield, Corrosion 38, 1982, p. 98.
10. G. Butler, H.C.K. Ison and A.D. Mercer, British Corrosion Journal 6, 1971, p. 23.
11. F.M. Bayyoumi, M.Sc. Thesis, Cairo University, 1995.
12. M.H. Lietzke, R.S. Greeley, W.T. Smith and R.W. Stoughton, Journal of Physical
Chemistry 64, 1960, p. 652.
13. D.D.G. Jones and H.G. Masterson, in Advances in Corrosion Science and
Technology, Vol. 1, New York, Plenum Press, 1970, p. 1.
14. F.A. Champion, in Corrosion Testing Procedures, London, Chapman and Hall, 1964,
p. 192.
15. D.D. Macdonald, A.C. Scott and P. Wentrcek, Journal of the Electrochemical Society
126, 1979, p. 908
16. U.R. Evans, in The Corrosion and Oxidation of Metals: Scientific Principles and
Practical Applications, New York, St. Martins Press , 1960, p. 819.
17. W.A. Ghanem, F.M. Bayyoumi and B.G. Ateya, Corrosion Science, in press, 1996.
414
Ghanem et al.
415
ABSTRACT
Aluminum and Al-alloys represent technologically and industrially important materials. The
electrochemical behavior of these materials in different solutions represents a major subject of
investigation. The corrosion characteristics of naturally passivated Al, Al-Cu, Al-6061 and Al-7075
were studied in nitric acid and nitric acid containing chloride solutions. The effect of the
concentration of anions on the corrosion behavior of these materials was traced.
Electrochemical impedance spectroscopy (EIS) is a powerful tool in studying corrosion and
passivation problems. Besides polarization techniques, the method has been applied successfully to
investigate the corrosion behavior of Al and Al-alloys. The Al-6061 alloy was found to be the most
corrosion resistant. In all cases, the naturally occurring passive film was too thin to impart complete
passivity. Equilibrium occurred between barrier film dissolution and surface passivation especially in
dilute solutions (< 0.1 M HNO3). The electrode/electrolyte interface was fitted to a parallel
resistor/capacitor combination. The barrier film formed on Al or Al-6061 behaved like a perfect
dielectric whereas that formed on Al-Cu or Al-7075 alloys deviated from the ideal capacitor behavior.
X-ray photoelectron spectroscopy (XPS) experiments have shown that Al-Cu alloys contain
remarkable amounts of Cu on the material surface. Scanning electron microscopy (SEM)
investigations have shown that the presence of Cu on the alloy surface initiates flawed regions which
are responsible for the increased corrosion rate of the Cu-containing alloys.
Key Words: Aluminium, aIuminium alloys, corrosion, electrochemistry, impedance, passivation
INTRODUCTION
Due to the technological importance of Al and Al-Alloys and their increased industrial
applications, the electrochemical behavior of these materials represents an important subject
for many investigators [1-10]. Investigations have been conducted to optimize the anodic
polarization and passive film growth [11-15]. The effect of anions like Cl and the
mechanism of their attack on the metallic surface has been a major research subject
[5,10,16,17]. The corrosion and passivation behavior of aluminum and its alloys has been
subjected to intensive investigation [18-21]. The use of nitric acid and nitric acid/phosphoric
acid mixtures in the surface finishing of aluminum and aluminum alloys, especially in the
household industry, required detailed information about the electrochemical behavior of these
materials in this medium [17,22-25].
417
Fundamental Aspects
Several techniques have been used to study the corrosion and passivation behavior of
metals and alloys. Electrochemical impedance spectroscopy (EIS) is becoming a well
established method for investigating electrochemical systems in which the solid/electrolyte
interface plays the main role [26]. One of its important aspects is the direct matching that
often exists between experimental impedance data and data obtained from discrete electrical
components which represent physical processes taking place in the system under investigation
[27]. Such electronic components are usually termed electronic models or equivalent circuits.
EIS and other polarization techniques are very useful in studying the corrosion and
passivation behavior of Al and its alloys. The polarization resistance, RP , which represents
the major indication of kinetic facility [28], and electrode capacitance, C , which represents
the main source for calculating the barrier layer thickness and its dielectric properties [29] are
the main factors used to describe and control the corrosion and passivation of these materials
[22-25].
In the present investigation, the electrochemical behavior of mechanically polished,
naturally passivated Al, Al-Cu, Al-6061 and Al-7075 was investigated in nitric acid and nitric
acid containing chloride solutions. An electronic model for the barrier layer/electrolyte
interface was described. The effect of chloride ion concentration on the corrosion and
passivation behavior of the metal and its alloys in nitric acid solutions was studied. X-ray
photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) were used to
investigate the materials surface.
EXPERIMENTAL PROCEDURE
Commercial-grade aluminum and aluminum alloys (Al-Cu, 6061 and 7075) were used as
electrodes. The mass spectroscopic analysis of these materials is presented in Table 1.
Electrodes in the form of cylindrical rods were mounted into glass tubes of appropriate
internal diameter with an epoxy resin leaving an exposed surface area of 0.50 , 0.21 , 0.20 and
0.21 cm2 for Al, Al-Cu, Al-6061 and Al-7075, respectively, to contact the test solution. The
electrolytic cell was an all glass, three electrode cell with a large surface area Pt counter
electrode and Ag/AgCl/Cl- (3 M KCl) reference electrode. The electrolytic solutions were
prepared using analytical grade reagents and triply distilled water. All measurements were
carried out at a constant room temperature of 25oC. The potentials were measured against the
Ag/AgCl/Cl- (3M KCI) reference {Eo = 0.1970 V(nhe)}. Before each experiment, the
electrode was mechanically polished with successive grades of emery paper down to 3/0, and
then with a smooth cloth and washed with triply distilled water. In this way, the electrodes
surface acquired a reproducibly bright appearance. For comparison, some experiments were
carried out after chemical etching of the electrodes surface to be sure that the mechanical
polishing had no effect on the alloys structure. The electrodes were chemically etched in a
80oC heated mixture of phosphoric, acetic and nitric acids for 5 minutes [22,23]. The
impedance data obtained for both mechanically polished and chemically etched electrodes
showed almost the same trend with slightly higher impedance values (5-10% higher) for the
chemically etched surface at different time intervals of electrode immersion in the test
solution.
EIS measurements were performed using the IM5d-AMOS system (Zahner Elektric
GmbH & Co., Kronach, Germany).
All experiments involved single frequency
measurements in the frequency domain of 0.1-105 Hz. To check the presence of another time
418
Al-Kharafi et al.
constant at lower frequencies, some experiments were conducted over a bandwidth of 1 mHz
- 105 Hz. The input signals amplitude was usually 10 mV peak to peak. Polarization
measurements were carried out using an EG&G (Princeton Applied Research) Model 273A
potentiostat/galvanostat interfaced to an IBM PS/3 computer. The XPS experiments were
carried out using an ESCA-Lab 200 (VG instruments). The surface was etched as required by
argon ion bombardment. In each spectrum, the XPS peaks of C 1S, O 1S, Al 2P and Cu 2P1
and 2P3 were traced. The electrodes surface was examined by SEM before and after
immersion in the test solution. The details of experimental procedures were as described
elsewhere [22-25].
Table1. Mass Spectrometric Analysis of the Different Electrode Materials in Mass %
Alloy
Al
Cu
Mg
Al
Al6061
Al-Cu
Al7075
99.23
97.09
93.43
90.93
0.043
0.201
4.80
1.17
0.217
1.40
0.229
2.21
Si
0.038
0.601
0.047
0.272
Fe
Mn
Ni
Zn
pb
Sn
Ti
Cr
0.164
0.193
0.499
0.124
0.001
0.012
0.024
0.067
0.010
0.010
0.012
0.007
0.027
0.029
0.025
4.95
0.001
0.000
0.721
0.000
0.003
0.000
0.006
0.000
0.006
0.016
0.015
0.024
0.001
0.248
0.001
0.046
419
Fundamental Aspects
(1)
C = A 0 /
(2)
where C is the electrodes capacitance, f is the frequency, Zim is the electrodes impedance, A
is the electrodes area, 0 is the permittivity of free space (8.85 x 10-14 Fcm-l), is the barrier
layer thickness and is the oxide film dielectric constant taken as 8.4 [33] considering that
the barrier layer consists mainly of A1-203. The calculated barrier layer thickness after a
long period of electrode immersion ( 4 hours) in the test solution ranges between 0.2 and 0.6
nm for all electrodes irrespective the barrier layer thickening or thinning that occurred at the
electrode/electrolyte interface. This thickness is about one-tenth of the thickness of the
barrier layer occurring on Al or Al alloys in neutral solutions (pH = 7) [6,34]. The presence
of such a barrier layer on Al or its alloys after long immersion times in nitric acid solution (
4 hours in 0.1 M solution) indicates the remarkable passive behavior of these materials in
these electrolytes.
Al-Kharafi et al.
The polarization and impedance data are in good agreement. Figure 4 presents the Tafel
polarization curves of the four materials investigated after reaching the steady state in 0.1 M
HNO3. The values of the polarization resistance, Rp , corrosion current, icorr , and steady state
potential, Ecorr , for the different electrodes as obtained from these measurements are
presented in Table 2. Figure 5 presents the impedance data of the electrodes after 250
minutes of electrode immersion under the same conditions. Taking into consideration the
polarization resistance and corrosion current data given in Table 2, the stability order of the
investigated materials after reaching the steady state in 0.1 M HNO3 (i.e., 45 minutes of
electrode immersion) follows the sequence:
Al-6061 > Al > Al-7075 > Al-Cu
After a long immersion time in the test solution (i.e., 4 hours), Al attained of comparable
stability or became even more passive than the Al-6061 alloy and the order changed to:
Al > Al-6061 > Al-7075 > Al-Cu
This is clearly reflected in the Nyquist plots of Fig. 5. The change in the order of
stability of Al and Al-6061 after long immersion times in the nitric acid solution is due to the
421
Fundamental Aspects
observed passivation of aluminum from the moment of immersion in nitric acid (Fig. 3). The
polarization resistance of the Al-electrode increased from 230 cm2 after 45 minutes of
electrode immersion in 0.1 M HNO3 solution at 25oC, to 372 cm2 after 250 minutes of
electrode immersion in the same solution under the same conditions.
Table 2. Values of RP , icorr and Ecorr (vs. Ag/AgCl/3M Cl-) for the Different Electrodes
Measured in 0.1 M HNO3 at the Steady State ( 45 min from electrode immersion)
Electrode
Al-6061
Al
Al-7075
Al-Cu
Rp, ( cm )
502
374
276
269
icorr, (A cm2)
113.5
121.2
169.6
196.1
Ecorr, (mV)
-500
-778
-271
-111
The data presented in this section show that Al-6061, either from the moment of
immersion in nitric acid or after a long period of immersion, represents the most stable alloy
in this solution of the alloys investigated. The results reveal that the presence of the small
amount of Mg (1.4%) improves the passivation behavior of the aluminum alloy. The mass
spectrometric investigation of the alloy showed that it contains 1.40% Mg and 0.60% Si.
Such a combination in a heat-treatable wrought alloy leads to the formation of a Mg2Si phase,
which is the basis for precipitation hardening. Either in solid solution or as submicroscopic
precipitate, Mg2Si has a negligible effect on electrode potential. The alloy is normally used
in a heat-treated form; therefore, no detrimental effects derive from the major alloying
element or from the minor components like Cr and/or Zn which are usually added to control
the grain structure. Copper additions which increase strength in the alloy are limited to very
small amounts 0.2% in this alloy (Al-6061), to minimize its effects on corrosion resistance
[35]. Increasing the copper content decreases the corrosion resistance of the alloy, as can be
seen for Al-7075 (1.17% Cu) and Al-Cu (4.80% Cu) in Table 2.
The electrochemical system can be represented by a theoretical model consisting of a
parallel combination of resistor, Rp , and capacitor, C , in series with the electrolyte
resistance, RS, [22,23]. Other equivalent circuit models including capacitive features and
inductive features are successful in describing the electrochemical behavior of Al or its alloys
in the very low frequency regions, (i.e., f < 0.1 Hz) [10,19,36]. Since it is necessary to
compare the electrochemical behavior of Al and the investigated alloys, it is useful to reduce
the theoretical model to the least number of components which can describe the dielectric
properties of the oxide film. The capacitor/parallel resistor model, investigated in the high
frequency region (f > 0.1 Hz) is suitable for such investigation. At high frequencies the
resistance of the inductive features becomes included in the polarization resistance, RP ,
which is equivalent to the corrosion resistance, Rcorr , of the material. The capacitive features
of the high frequency semicircle are related to the barrier layer itself [30,33]. The impedance
data of the different electrodes were correlated to the model described above.
A procedure of data fitting with minimum error was used in which a fitting program was
applied to fit the experimental data to the computer-generated data. The program used
422
Al-Kharafi et al.
enables data fitting in the required range of frequency. For the measurements presented, it
was necessary to fit experimental data of the high frequency semicircle to the computergenerated data of the proposed model. For data fitting procedures, Bode plots are always
recommended as standard impedance plots [26,37]. Figure 6 presents the experimental Bode
plots for Al-6061 after 4 hours of electrode immersion in 0.1 M HNO3 (dotted line)
correlated to the computer-generated data of RS = 25.2 , Rp = 1.39 k and C = 2.36 F
according to the data fitting program. The data fitting of Al-6061 gives a mean error in the
absolute impedance of 1.4% and a mean deviation in the phase angle, , of 1.00. The
procedure of data fitting was applied to other electrode materials and also to impedance
spectra taken at different time intervals of electrode immersion in the test solution. The Al
and Al-6061 impedance data represent the best fitt to the theoretical model after reaching the
steady state, whereas Al-Cu showed the largest deviation. The absolute impedance and phase
angle deviation for Al-Cu electrodes after 4 hours of electrode immersion in 0.1 M HNO3
solution are 3.1% and 1.6o, respectively. The small deviation of the absolute impedance
values obtained with Al-6061 and pure Al indicate that the barrier layer on these materials
approaches ideal capacitor behavior.
Nyquist plots of Al-Cu (), Al7075 (), Al (----) and Al-6061 (- -) after 250 min of electrode
immersion in 0.1 M HNO3. The
values of Rp for each electrode in
2
cm are 122, 142, 372 and 234,
respectively
Fundamental Aspects
were mechanically polished and investigated in 0.1 M HNO3 solutions containing different
concentrations of Cl- ions ranging between 3.5 mM and 0.35 M. A typical example of the
data from these investigations is presented as Nyquist plots for the Al-Cu alloy in Fig. 7. For
all investigated materials in all measurements, two semicircles were recorded. A high
frequency semicircle and a low frequency inductive loop. The diameter of the high frequency
semicircle depended on the concentration of Cl- (Fig. 7). It decreased as the concentration of
Cl- ions increased. This means that the natural passivity of Al or Al alloys decreases in the
presence of chloride ions, as was reported for aluminum. Chloride ions attack the base metal
by dissolving the passive film at defective areas [16,37,38]. The decrease of polarization
resistance and passive layer thickness with increasing Cl- ion concentrations means that the
native barrier layer is too thin to impart complete passivity. As the concentration of Clincreases, the extent of surface attack increases and Cl- spreads laterally beneath the original
native film leading to the loss of its passive characteristics with the formation of a
nonprotective, oxyhalide layer on the metallic surface [16,24,25]. At very low concentrations
of Cl- (i.e., 3.5 mM), the rate of barrier layer removal is very low and is exceeded by the rate
of passive film repair that occurs in nitric acid solutions; hence, no remarkable attack can be
observed. In this case, oxide film thickening occurs as was indicated by the increase of 1/C
versus t relations [17,24,25]. At higher concentrations of Cl- (i.e., > 35 mM), the rate of
barrier film removal is compensated for by the rate of passive film formation, and equilibrium
is attained in which an approximate constant value of can be calculated. The remaining
barrier layer thickness and its polarization resistance depends on the electrode material.
Figure 8 presents the effect of Cl- ions with the same concentration (i.e., 35 mM) on the
different electrode materials. As can be seen from the Nyquist plots of Fig. 8, Al-6061 has
better corrosion resistance against Cl- than the other alloys investigated and even better
resistance than aluminum itself. The Al-Cu and Al-7075 alloys are much affected by the
presence of chloride ions. A remarkable decrease in the corrosion resistance of both alloys
with the increase of the concentration of Cl- was recorded. This behavior can be attributed to
the alloys constituents. The presence of Mg in the Al-6061 alloy improved the corrosion
characteristics of the alloy in chloride media, whereas the presence of Cu increased the
corrosion rate of the alloy. The values of corrosion resistance of the different materials after
reaching the steady state in 0.1M HNO3 containing 35 mM Cl- took the order, Rp Al-6061 >
Rp Al > Rp Al-7075 > Rp Al-Cu. The values in k-cm2 for the sequence are 0.754, 0.382,
0.157 and 0.097 for Al-6061, Al, Al-7075 and Al-Cu, respectively.
The presence of Cu on the alloys surface was confirmed by XPS measurements. Figure
9 presents the XPS spectra for Al, Al-Cu and Al-6061. In all spectra, the characteristic peaks
of aluminum (Al 2P at 75.5 eV and Al 2S at 120.0 eV), oxygen (O 1S at 532.5 eV) and
carbon (C 1S at 285.5 eV) were recorded. The XPS of Al-Cu (Fig. 9b) contains additional
copper peaks (Cu 2P3 at 932.5 eV and Cu 2Pl at 952.5 eV) which indicate the presence of Cu
on the electrodes surface even after 3 hours of electrode immersion in the test solution. The
XPS of Al-6061 did not show a pronounced Mg peak, i.e., the characteristic sharp Mg XPS
peak (Mg 1S at 1305 eV) is not present [39]. This means that Mg is present more likely in
the form of Mg2Si in the Al-6061 bulk and not on the alloys surface. The similarity between
the XPS spectra for Al and Al-6061 (compare Fig. 9a and b) explains the close corrosion
behavior of both materials and supports the conclusion that the barrier layer on both materials
consists of a stable Al2O3 film. The presence of Cu on the Al-Cu surface is responsible for
424
Al-Kharafi et al.
the higher rates of corrosion recorded for this alloy. It initiates cathodic areas or flawed
regions which leads to the observed decrease in the corrosion resistance after long immersion
times in the test electrolyte. The presence of flawed regions on Al-Cu was confirmed by
SEM. Figure 10 presents the scanning electron micrographs of Al and Al-Cu surfaces before
immersion in the test solution (Fig. 10a and b, respectively) and of an Al-Cu surface after 3
hours of immersion in 0.1 M HNO3 containing 0.35 M Cl-.
425
Fundamental Aspects
- cathodic reaction:
H+ + e- H
H2O + e- H + OH-
(3)
(3)
H + H2O + e- H2 + OH-
(4)
(5)
OHads..+ e- OH-
(6)
Al + OH- Al(OH)ads + e-
(7)
(8)
(9)
- anodic reaction:
In the presence of Cl- ions, metal dissolution occurs through the attack of Cl- according to
Al + Cl- AlClads. + e-
(10)
(11)
(12)
and the most appropriate cathodic counterpart is reaction (3) followed by reaction (4). The
presence of cathodic areas enhances the corrosion process which was observed with the Cucontaining Al-alloys (i.e., Al-Cu or Al-7075). The presence of Cu on the material surface
increases the ratio of cathodic/anodic areas leading to an increase in the corrosion rate. The
natural tendency of Cu or Zn to form oxyhalide complexes is also an additional effect which
causes the loss of the protective properties of the naturally occurring barrier layer in the
chloride solution. In chloride-free nitric acid solutions, the formed Al(OH)3 can be oxidized
to the stable A12O3 passive film. The oxidation power of nitric acid depends on its
concentration [22-24]. This explains the passive behavior of Al and Al-6061 in nitric acid
solutions. The presence of Cu on the surface of the Cu-containing alloys increases the
cathodic areas, and hence, increases the tendency for galvanic corrosion to occur, which
explains the comparatively high rates of corrosion of these alloys after long immersion time
in nitric acid solutions (Table 2).
426
Al-Kharafi et al.
. SEM micrographs of
mechanically polished Al(A), AlCu (B) and Al-6061 (C) after 3 h
of immersion in 0.1 M HNO3
solution containing 0.35 M Cl
CONCLUSIONS
The corrosion and passivation behavior of Al, Al-6061 Al-7075 and Al-Cu, is dependent
of both the alloying element and the corrosive medium. In nitric acid and nitric acid
containing Cl- ions solutions, Al-6061 has the highest corrosion resistance. This alloy with its
1.40% of Mg. and 0.60% of Si behaves like a perfect dielectric. The corrosion behavior of
which is most likely similar to aluminum, especially after long periods of immersion in nitric
acid or nitric acid containing chloride solutions. The presence of Cu on the surface of Cucontaining alloys initiates flawed regions in the barrier layer which are responsible for the
higher corrosion rates of these alloys.
ACKNOWLEDGEMENT
427
Fundamental Aspects
The financial support of Kuwait University, Research Grant No. SC060, is gratefully
acknowledged.
REFERENCES
1. M. Heine, D. Keir and M. Pryor; J. Electrochem. Soc. 113, 1965, p. 24.
2. J. Painot and J. Augustynski, Electrochim. Acta 20, 1975, p. 747.
3. D.M. Drazic, S.K. Zecevic, R.T, Atanososki and A.R. Despic, Electrochim. Acta 28,
1983, p. 968.
4. Y. Fukuda and T. Fukushima, Electrochim. Acta 28, 1983, p. 47.
5. W.A. Badawy, M.M. Ibrahim, M.M. Abou-Romia and M.S. El- Basiouny, Corrosion 42,
1986, p. 342.
6. W.A. Badawy, M.S. El- Basiouny and M.M. Ibrahim, Ind. J. Technol. 24, 1986, ,p. 1.
7. M.G. Khedr and A.M.S. Lashien, J. Electrochem. Soc. 136, 1989, p. 968.
8. G. Burri, W. Luedi and O. Haas, J. Electrochem. Soc. 136, 1989, p. 2167.
9. C.B. Breslin and W.M. Carroll, Corros.Sci. 34, 1993, p. 327.
10. C.M.A. Brett, I.A.R. Gomes, J.P.S. Martins, J. Appl. Electrochem. 24, 1994, p. 1158.
11. M. Elboujdaini, E. Ghall, R.G. Barradas and M. Glrgis, Corros. Sci. 30, 1990, p. 855.
12. N. Khalil and J.S.L. Leach, Electrochim. Acta 31, 1986, p. 1279.
13. V. Surganov, P. Morgan, J.G. Nielsen, G. Gorokh and A. Mozalev, Electrochim. Acta 32,
1987, p. 1125.
14. V.P. Parkhutik, J.M. Albella, Yu. E. Nlakushok, 1. Montero, J.M. Martinez Duart and V.L
Shershulskii, Electrochim.Acta 35, 1990, p. 955.
15. V.P. Parkhutik, V.T. Belov and M.A. Chemyckh, Electrochim. Acta 35, 1990, p.961.
16. A.A. Mazhar, W.A. Badawy and M.M. Abou-Romia, Surface and Coating Technology
29, 1986, p. 335.
17. F.M. Al-Kharafi and W.A. Badawy, Proceedings of the 186th Electrochemical Society
Meeting, Miami, Florida, USA, October 1994.
18. T. Hurlen, H. Lian, O.S. Odegerd and T. Valand, Electrochim. Acta 29, 1984, p. 679.
19. T. Hurien and A.T. Haug, Electrochim.Acta 29, 1984, p. 1133 and p. 1161.
20. W.C. Moshier, G.D. Davis and J.S.Aheam, Corros. Sci. 27, 1987, p.785.
21. L. Tomcsanyi, K. Varga, I. Bartik, G. Horayi and E. Maleczki, Electrochim. Acta 34,
1989, p. 855.
22. W.A. Badawy and F.M. Al-Kharafi, B.Electrochem. 11, 1995, p. 505.
23. F.M. Al-Kharafi and W.A. Badawy, Ind. J. Chem. Technol., In press.
24. F.M. AI-Kharafi and W.A.Badawy, Electrochim. Acta 40, 1995, p.1811.
25. W.A. Badawy and F.M. Al-Kharafi, Corros.Sci., Accepted.
26. D.D. Macdonald, S. Real, S.I. Smedley and M. Uraquidi-Macdonald, J.Electrochem. Soc.
135, 1988, p. 2410.
27. W.A. Badawy and Kh.M. Ismall, Electrochim. Acta 38, 1993, p. 2231.
28. J. Koryta, J. Dvorak and L. Kavan, Principles of Electrochentistry, Chap. 5, J. Wiley &
Sons, Chichester, 1995.
29. J.M. Albella, I. Montero and J.I. Martinz-Durat, Thin Solid Films 125, 1985, p. 57.
30. H.J.W. Lendednk, W.V.D. Linden and J.H.W. De Wit; Electrochim. Acta, 38, 1993, p.
1989.
428
Al-Kharafi et al.
31. S.E. Feres, M.M. Stefenel, C. Mayer and T. Chierche, J. Appl. Electrochem. 20, 1990, p.
996.
32. C.M.A. Brett; J. Appl. Electrochem. 20, 1990, p. 1000.
33. C.M.A. Brett; Corros. Sci. 33, 1992, p. 203.
34. S. Srinivasan and C.K. Mital, Electrochim. Acta 39, 1994, p. 2633.
35. E.H. Hollingworth and H.Y. Hunsicker, Corrosion Resistance of Aluminium Alloys in
Metal Handbook, 9th ed., Vol. 2, 1990, Americam Society for metals, Metals Park, Oh,
USA, pp. 204-236.
36. J. Bessone, C. Mayer, K. Juttner and W.J. Lorenz, Electrocim. Acta 28, 1983, p. 171.
37. P.L. Cabat, F.A. Centellas, J.A. Garrido, E. Perez and H. Vidal, Electrochim. Acta 36,
1991, p. 179.
38. W.M. Carroll and C.B. Breslin, Br. Corros. J. 26, 1991, p. 255.
39. E. Adem, VG Scientific XPS Handbook, 1st ed., VG Scientific Ltd., England, 1989.
40. W.A. Badawy and F.M. AI-Kharafi and A.S. El-Azab, J. Appl. Electrochem. (Submitted).
41. F.M. Al-Kharafi and W.A. Badawy, Corrosion (Submitted).
429
ABSTRACT
The development of the chemical, fertilizer, petrochemical, refining and energy industries
depends, in most cases, on resolving the problems associated with the use and maintenance of stainless
steels. The most important problem faced with the use of stainless steels is intergranular corrosion
(IGC). This subject has attracted the attention of many research organizations for several years and
still concerns many to date.
Key Words: Austentic stainless steel, weld metal, intergranular corrosion
INTRODUCTION
Nowadays, the metal manufacturing industries produce chromium and nickel-bearing
austenitic stainless steels which are highly resistant to intergranular corrosion (IGC). This
level of resistance is achieved by stabilizing the characteristics of the steels by adding
titanium or niobium, or by decreasing the percentage of carbon in the steel to a very low level
or both [1]. In most cases, these stainless steels are used in welded mechanical equipment
which are also repaired by welding. Such uses, however, might lead to IGC (sensitization),
especially when the steel remains at temperatures of 500-700C during the welding process.
Within this temperature range, depletion of chromium can occur at the grain boundaries in the
heat affected zone. Welding or repeated welding promotes such a phenomenon. Therefore, it
is deemed desirable to have a stainless steel alloy that resists sensitization during welding in
order to prevent IGC. One of the basic methods used to stabilize the austenitic chromiumnickel stainless steel weldments is through the addition of titanium or niobium.
After welding, steel weldments passes through the temperature range of 900-1000C for
a period of time. This allows the formation of carbide stabilizers such as Ti and Nb carbides
[2-4], resulting in lowering the carbon content in the solid solution. However, when such an
alloy reaches the critical temperature range for sensitization, i.e., 500-750C, chromium
carbide is formed (i.e., Cr23C6) along the grain boundaries. This results in dispersed and unconnected areas depleted in chromium. Therefore, the grain boundaries become less
resistance to IGC than those that are stabilized with Ti or Nb. The percentage of these latter
alloying elements in the steel should depend on the amount of carbon present in the steel.
431
Fundamental Aspects
This matter appears simple, but many complications, however, occur upon the addition
of Ti or Nb. Titanium has a higher affinity for reaction with carbon than does chromium. Ti
is also more reactive to oxygen than chromium or the residual elements such as Mn and Si
are. Therefore, during electric arc welding, a titanium-stabilized steel electrode tends to react
with oxygen and be consumed completely. To avoid such complications, inert gas is used
during welding of such electrodes. However, this increases the cost of the components to be
welded. Alternatively, titanium can be replaced by niobium with its lower oxidation rate as a
stabilizer for the steel weld metal.
When mechanical components are operated under severe corrosive conditions and/or are
exposed for an extended period to a temperature in the range of 500-600C, it is
recommended that the amount of Nb to be 10-12 times greater than the percentage of carbon
in the steel. In addition to the amount of Nb which is required in such weld metal, the amount
of azote and carbon need to be calculated [4,5]. Therefore, more Nb is required than is
mentioned above, and this leads to a loss of steel toughness and the appearance of hot short
cracks in the weld metal during the welding process [6].
The sensitivity of welding materials to IGC increases with increases in carbon, titanium
and niobium. When using a welding electrode with a maximum carbon percentage of 0.06,
the sensitivity of weld metal may be increased. However, this does not negate the weld
metals sensitivity to IGC, especially during solid welding processes or applied on different
layers. This is related to the presence of large percentage of carbon in the welding material
the migration of carbon from the base metal or the degradation of carbon containing
materials that cover the welding electrode [7].
The chromium-nickel steels with niobium added had the tendency to crack during
cooling. This action appears more than in castings, solid welding joints and during the
welding of thick plates. This damage increases with the increase in acidity of the slag during
welding [8] (especially for electrode materials containing cilium) which produces hot short
cracks. Getting rid of compounds containing cilium in materials covering electrodes is
impossible.
The negative effect of niobium on hot short cracking is associated with the small
dissociation of niobium in iron especially at the low eutectic melting temperature of Fe-Nb
[9,10]. This eutectic effect cannot be avoided in practice unless it is associated with the
amount of niobium and carbon. Niobium usually increases the ferrite phase in steels,
especially if it is present in steel in a ratio of 1:10 with respect to carbon. Therefore, due to
the inhomogeneous concentrations in weld metal, microscopic cracks appear in pure
austenitic areas. This is expected since niobium activate cracking in weldments of pure
austenite. One may thus conclude that stabilizing the chromium-nickel steels with niobium is
associated with many technological difficulties.
Molybdenum is a more positive stabilizing additive with this respect. Mo is known to
posses a large degree of dissociation in iron, chromium and nickel. The eutectic melting
point of Mo is not that different from the melting point of the original metals of Fe, Ni and
Cr. Metals that contain Mo do not exhibit hot short cracks. Molybdenum is also known to
promote the ferrite phase and has the affinity to react with carbon, but to a lesser degree than
Nb with carbon. Therefore, Mo aids in raising the resistance of weld metals of chromiumnickel stainless steels to hot cracks.
432
Karfoul
433
Fundamental Aspects
Phase Composition
S(%) Grain Diameter (m)
4
20
5
20
10
20
4
20
10
20
Composition No.
1
2
3
4
5
C
0.11
0.11
0.11
0.11
0.11
P
0.03
0.028
0.027
0.033
0.03
V
2.85
1.86
Composition No.
1
2
3
4
5
(%)
4.7
4.4
8.2
6.0
9.0
Phase Composition
Grain Diameter (m)
21
17
19
17
17
The amount of the ferrite phase on the weld metal specimens was determined
magnetically by an -phase meter with 5% error, as is shown in Fig. 1. These same
specimens were also used to study the weld metals resistance to IGC.
RESULTS
A metallurgical microscope was used to measure the austenite grain diameter of the weld
metals, as shown in Fig. 2. After being welded, the specimens were prepared (Fig. 1) and
heat-treated at a temperature range of 500-800C for different time periods as shown in Table
2. Then, the specimens were quenched with water. To determine the susceptibility of the
specimens to IGC after the heat treatment, they were all immersed in Strauss solution for 24
434
Karfoul
hrs. Strauss solution is made up of 100 gr of CuSO4 5H2O + 0.1l H2SO4 + 1l of distilled
water + thin copper sheets.
Figure 1. The Location of the points where the ferrite phase was measured
in the welded metal
Composition No. 1
Composition No. 2
Composition No. 4
Composition No. 3
Composition No. 5
435
Fundamental Aspects
Figure 2. Microstructures of the weld metals for the different studied compositions
Table 2. Time in Minutes of the Different Heat-Treatment Temperatures Studied
550
600
650
700
750
800
Heat Treatment
Temperature (C)
-
25
50
3
5
10
25
10
25
10
25
500
55
110
300
500
5
30
50
10
300
10
30
50
110
300
50
10
25
50
100
300
500
25
50
100
300
500
0.5
1
3
5
10
5
10
30
50
110
300
500
5
10
1
3
5
10
100
5
30
50
300
10
30
50
110
300
500
10
25
50
100
300
500
25
50
110
300
500
5
10
30
50
90
-
5
10
30
50
100
-
50
100
300
500
50
100
300
500
10
25
50
100
300
60
25
50
110
300
500
50
110
110
300
After being boiled for 24 hours. in Strauss solution, the specimens were bent to a 180
angle. If no cracking was observed in the bent samples, they were considered to be resistant
to IGC.
DISCUSSION
The aqueous solution of copper sulfate and sulfuric acid was chosen because it attacks
only the regions of the specimens with chromium contents of < 12%. This negates the use of
weight-loss or other methods to check whether or not such specimens are susceptible to IGC.
On the other hand, results obtained using acetic acid may require the determination of the
weight loss of specimens because IGC might not be well defined. This is because in this
case, the acid attacks regions containing more than 12% Cr and removes grains from the
436
Karfoul
metal surface. Therefore, weight -loss measurements are not representative of intergranular
corrosion.
It can be seen in Figs. 3, 4 and 5 that the addition of 6 wt% Mo to the weldments
increased greatly the IGC resistance of the austenitic stainless steel weld metal. It also
increased annealing of the microstructure of the weld metal, resulting in increasing the
austenitic grain boundary surface area and thus not allowing the precipitation of Cr23C6 and
preventing the depletion of Cr around the grains. The addition of Mo also aids the formation
of ferrite phase in the microstructure of the weld metal and thus decreases the IGC
susceptibility of the metal.
It was also observed from Figs. 6 and 7 that the replacement of half of the Mo by V in
the weld metal of the composition No 3 did not change the resistance of the alloy to IGC,
indicating similarity of V and Cr. However, the increase in the amount of ferrite in the
microstructure of the weld metal tended to increase the resistance of Cr-Ni weld metals to
IGC, as shown in Fig. 7.
437
Fundamental Aspects
E.C. Bain, R.H. Aborn and J.J.B Rutherford, The nature and prevention of intergranular
corrosion in austenitic stainless steels, Transactions of the American Society for Steel
Treating, Vol. XXI, No. 1, 1933, pp. 481-509.
2.
V.V. Levitin and V.I. Cirashikova, precipitation of carbides on the grain boundaries
during the production of austenitic steel, Metallovedmie and Thermocheskoe, No. 8,
1960, pp. 20-25.
V. Chihal, N. Lehka and J.K. Malik, Probleme der interkristalline und der hesser tinienkorrosion van schweibvindunger der mit niob stabilisierten korrosiosbestandiger stahle.
Metalloberflache angewandte elekrochemie, Iq. 26, heft. 12m 1972, pp. 453-558.
W.O. Binder, C.M. Brown and S.R. Frank, Resistance to sensitization of austenitic
chromium-nickel steels of 0.03% max carbon content, Transactions of the American
Society for metals (ASM), Vol. 41, 1994, pp. 1301 - 1371.
R.A. Mulford, E.L. Hall and C.L. Brint, Sensitization of austenitic stainless steels. II
Commercial purity alloys, Corrosion 39, 4, April 1983.
I.Z. Kogan, Niobium in welding electrodes, Heat resisting, No. 4, 1951, pp. 1-3.
H.J. Rocha, Die sensibilisiertes austenisches stahle durch chromkarbide, Zeitchrift fur
Schweisstechnik, No. 3, 1962, pp. 98-106.
B.I. Medovar, Welding of heat resisting austenitic stainless steel and alloys, Moscow,
Machinostrorkue, 1966, pp. 202
G.L. Petrov, V.N. Zemzin and F.G. Goncherovsky, welding of heat resisting stainless
steels, Moscow, Petersburg, Machgas, 1963, pp. 53
3.
4.
5.
6.
7.
8.
9.
438
Karfoul
10. M.Ck. Sharshorov, Hot cracks during the welding of heat resistant alloys, Moscow,
Machinostructure, 1973, pp. 183.
11. B.A. Movchan, Edges of crystals in cast metalls and alloys, Keef, Teschnika, 1970, p.
151.
12. F.F. Ckhimushin, Stainless steel, Metallorg, Moscow, 1967, p. 351.
13. F.R.G. Patent, No. 148342, 29, 35/30; February 1973, Welding electrods.
14. M.K. Karfoul, Syrian patent No. 4405, 13 December 1992, Welding electrodes for
stainless steel weldments.
15. M.K. Karfoul, Intergranuler corrosion of austenitic weld metal type 18-10 with
molybdenum, The Sixth Middle East Corrosion Conference, Conference Proceeding,
NACE, Vol. 1, pp. 313 - 328.
16. E.
Houdermont,
Handbuch
der
Soonder
Stahlkunde,
Springer-verlag,
Berlin/Gohingen/Heidd, 1956, Russian Translation, Moscow, 1960, p. 1064.
439
ABSTRACT
The crystallization of amorphous FeCr9P6C3Si0.2 alloy was investigated by x-ray diffraction
(XRD), differential thermal analysis (DTA) and scanning electron microscopy (SEM). Specific
differential heat curves of the FeCr9P6C3Si0.2 alloy exhibited three exothermic peaks indicating that
the crystallization of the amorphous alloy occurred through the formation of three kinds of metastable
crystalline phases. The deterioration of corrosion resistance by the crystallization of the amorphous
FeCr9P6C3Si0.2 alloy was studied by electrochemical methods to correlate the corrosion behavior
with the increase in the heterogeneity of the alloy. As soon as the stage formed in the amorphous
matrix, the anodic current density increased. The current density in the active and passive regions
increased continuously in sulfuric acid solution during the crystallization processes. Chemical
heterogeneity, based on the formation of precipitation segregation and other compositional
fluctuations, seemed to be responsible for the deterioration of the corrosion resistance.
Keys Words: Amorphous alloys, corrosion, crystallization, potentiodynamic measurements
INTRODUCTION
The corrosion behavior of amorphous alloys was first studied in 1974 [1]. It was then
extensively reviewed [2-6] for simple binary alloys such as Fe80B20 as well as commercial,
multicomponent systems. Amorphous iron-based alloys prepared by quenching from the
liquid state contain a large amount of various metalloid elements that stabilize the amorphous
structure in the solid state. Among the metalloid elements, phosphorus is the most effective
at concentrating chromium in the passive film [7], and hence, the passive film formed on the
amorphous alloys contained phosphorus and a small amount of chromium consisting
exclusively of hydrated chromium oxyhydroxide. This is partly responsible for the extremely
high corrosion resistance of these amorphous alloys [8-9]. Amorphous alloys containing P
were almost always more corrosion resistant than alloys containing B, Si or C. However, the
alloys containing P became much less corrosion resistant [10,11] after treatment at the
crystallization temperature, at which point P migrated into the grain boundaries and caused
severe intergranular corrosion. The chemical heterogeneity seemed to form a high density of
weak points in the passive film with respect to corrosion as well as localized corrosion attack.
The heat treatment of amorphous alloys gives rise to the formation of various metastable
crystalline phases (MS) in the amorphous matrix before the formation of stable crystalline
441
Fundamental Aspects
phases [12]. In this work, amorphous FeCr9P6C3Si0.2 alloy was used. Mainly
potentiodynamic polarization experiments were conducted to understand the electrochemical
corrosion of the alloy. The effect of heat treatment on the behavior of the amorphous alloy in
aerated sulfuric acid media was investigated.
EXPERIMENTAL PROCEDURE
Amorphous FeCr9P6C3Si0.2 alloy ribbons 2 mm in width and 10 m in thickness were
produced by a rapid quenching technique (melt-spinning). The number attached to a
respective element in the alloy formula denotes the nominal content in atomic percentage.
After isothermal heat treatment of the alloy in an evacuated quartz tube at various constant
temperatures at a gas pressure of 3.10-6 torr, diffractometric measurements were made using
a diffractometer, with Co K radiation at a scanning speed of 8o/minute.
Differential thermal analysis (DTA) at a heating rate of 10 K/minute was carried out to
confirm the multistage crystallization which produced multiple exothermic peaks. The
crystallization process was also examined by a scanning electron microscopy (SEM) after
undergoing isothermal heat treatment.
The electrochemical experiments were performed with an Amel potentiostat system.
Anodic polarization curves for the alloy were measured potentiodynamically with a potential
sweep rate of 1 mV/s. The electrochemical measurements were conducted in unstirred,
aerated 1 M H2SO4 solution which was prepared using a reagent. The alloy was not
mechanically polished. Both sides of the ribbons were immersed in the test solutions. All the
experiments were carried out at room temperature. Polarization studies were conducted in a
simple electrolytic cell at three electrode using platinum counter electrodes and a saturated
calomel (reference) electrode (SCE).
RESULTS
Differential Thermal Analysis (DTA) Measurements
The DTA curves for the amorphous FeCr9P6C3SiO.2 alloy exhibited three exothermic
peaks as shown in Fig. 1. The first peak was at about 448C, the second peak was at 489C
and the final peak was at 578C. This indicates that the crystallization of the amorphous
alloy occurred through the formation of three kinds of MS. In the case of heat treatment at
300 and 400C, the pace of the thermograph was not modified. However, the DTA curves for
the alloy treated at 500C for 1, 2 and 3 hours exhibited only one exothermic peak. In this
case, the crystallization was only partial. But, for the alloy treated at 500C for 8 hours or at
600, 700 and 800C for 1 hour, crystallization was total.
X-Ray Diffraction (XRD) Measurements
The x-ray diffraction (XRD) patterns for the amorphous FeCr9P6C3SiO.2 alloy and a
series of isochronal heat treatments are shown in Fig. 2. It is evident that the as-quenched
state was typical of the amorphous state, and no crystalline phases were observed. With
annealing at 300 and 400C the alloy stayed amorphous. When the temperature was
increased, the x-ray pattern became totally crystalline. As shown in Fig. 2, XRD patterns
revealed that the crystallized FeCr9P6C3SiO.2 alloy consisted of many phases. XRD
confirmed the presence of -Fe as an fcc phase with a = 2,866 in the ribbons annealed at
442
Hajji et al.
500C. Because of the very complicated nature of the diffraction patterns and the intense
diffraction lines of the -Fe phase, an accurate analysis of the lattice constants of the other
phases was not possible.
The crystallization of various amorphous metal-metalloid alloys has been studied by
many authors. When the metalloid concentration is not exceedingly high, such as at 28
atomic percentage, the crystallization of amorphous alloys generally takes place as follows:
the heat treatment of the amorphous alloy gives rise to the precipitation of a MS in the
amorphous matrix. This phase contains a large amount of the main metallic component of the
alloy and thus it has the same crystal structure as the main metallic component. The
amorphous phase then disappears by the formation of two or three MS, through
transformation diffusion of various elements and by recrystallization and/or decomposition of
the metastable phases.
2.
Fundamental Aspects
Figure 3. Breaking faces of the alloy FeCr9P6C3Si0,2 thermally treated at 300C for 1 hour
(a), 500C for 1 hour (b) and 800C for 1 hour (c), Micrograph of the shining face
of the alloy FeCr9P6C3Si0,2 after annealing at 500C for 1 hour (d), 800C for 3
hours (e) and mate face at 800C for 3 hours (f). Micrograph of the alloy
FeCr9P6C3Si0,2 after annealing at 500C for 1 hour (g). x-ray cartography of the
shining face of the alloy FeCr9P6C3Si0,2 after annealing at 800C for 1 hour (h)
Scanning Electron Microscopy (SEM)
Scanning electron microscopy (SEM) images obtained on breaking faces that have been
thermally treated are shown on Fig. 3. For samples annealed at 300 or 500C for 1 hour,
these alloys formed in a disordered grain stacking. They seemed to have a spherical form,
and their size increased with increasing temperature (Fig. 3a and 3b). On the other hand,
when the temperature and the annealing time increased, the alloy presented a mixture of two
aspects: a granular aspect and a column-like aspect (Fig. 3c). The observed crystallization
was probably due to an intrinsic heating up of the alloy during the annealing process.
Annealing of the alloy did not change the state of the external surface of the alloy. Indeed the
state of the surface stayed amorphous, as shown in the SEM micrograph (Fig. 3d). In the case
of the alloy annealed at 800C for 3 hours, the state of the surface of the shining face (Fig. 3e)
seemed to be formed by a granular stacking of a quasi-spherical form, even if the mate face
444
Hajji et al.
always stayed amorphous (Fig. 3f). In order to clarify this phenomenon, note that the
micrograph in Fig. 3g, obtained for a sample annealed at 500C for 1hour, presents a mixture
of two different crystallographic aspects: an amorphous aspect (alloy surface) and a crystal
aspect (inside the alloy).
An x-ray cartograph giving the distribution of the Fe, Cr, P and C elements of a sample
annealed at 800C for 1 hour showed good homogeneity of the shining surface (Fig. 3). This
confirms that the surface of the sample was not affected by the temperature. These results
could be explained by the fact that increases in the annealing temperature and time led to an
increase in the molecule mobility inside the alloys before their freezing into a crystal state.
Therefore, the grain size increased with annealing temperature and time. Nevertheless, this
increased mobility did not lead to a perfect atomic order which would have filled the entire
volume of the alloy, mainly the external surface as shown by the SEM results. The inside of
the alloy was then formed by a stacking of micro-crystallites separated by a granular
boundary which are probably disordered. Furthermore during the growth of such microcrystals, depending on the annealing temperature and time, it is possible that some impurities
formed around the grains with compositions quite different from those of the crystallites.
Fundamental Aspects
Figure 4 shows changes in the anodic polarization curves of the alloy measured in 1 M
H2SO4 according to the temperature of heat treatment at different time periods. The anodic
polarization curve of the untreated alloy is also shown in Fig. 4 for comparison. The various
anodic parameters determined from these curves are given in Table 1. The curve for the
amorphous alloy exhibits a typical active-passive transition (Fig. 4), and passivation in 1 M
H2SO4 solution. When the alloy was amorphous with the annealing (300 and 400C), the
activation current density began to increase slowly. However, as soon as the first crystalline
phase was formed in the amorphous matrix, the speed of the activation current density began
to increase. The corrosion current density for activation (Ic) and for passivation (Ip) was
dependent on the annealing temperature. Before annealing, the activation current density (Ia)
was 34 A/cm, and after annealing (Ic) became 40, 64, 726, 13793, 32307 and 47984
A/cm at 300, 400, 500, 600, 700 and 800C for 1 hour, respectively. The current density in
the active and passive regions continuously increased during all the stages of nucleation. The
crystallized alloy also exhibited a wide passivity range. The superior corrosion resistance of
the amorphous alloy decreased with the crystallization of the alloy in 1 M H2SO4 solution.
Table 1.
600C 700C
-375
-382
13793 32307
1034
462
800C
-380
47984
161
DISCUSSION
The present results revealed clearly that the formation of a crystalline phase in the
amorphous matrix increased the anodic current density. The anodic current density of
FeCr9P6C3Si0.2 alloy in the active and passive regions continuously increased during the
growth of metastable phases crystallites. Therefore, the crystallization of the amorphous
alloys led to the appearance of chemical heterogeneity with a subsequent increase in the
current density in the active region. The appearance of chemical heterogeneity also increased
the current density in the passive region. It has been assumed [13-16] that the passive film
was not essentially uniform but contained weak points (micropores) which were responsible
for the apparent passive current density in aggressive solutions. The micropores could be
formed on heterogeneous sites of the underlying alloy surface as well as on the phases which
are relatively difficult to passivate. Accordingly, the formation of chemically heterogeneous
sites in the alloys by heat treatment increased the passive current density. The question raised
is whether or not the chemical heterogeneity, in comparison with structural heterogeneity, is a
dominant factor in decreasing the corrosion resistance. The present authors [17] have shown
that the rapidly quenched, single phase alloys showed significantly high corrosion resistance
in comparison with the corresponding ordinary crystalline alloys. Naka et al. [11] have
reported that the passive current density of the Fe-10Cr-13P-7C alloy increased by two orders
of magnitude due to the formation of the solid solution phase in the amorphous matrix.
446
Hajji et al.
Therefore, rapidly quenched single phase alloys show significantly high corrosion
resistance. In contrast, heat treatment inevitably induces solid state diffusion and hence
results in various compositional fluctuations such as precipitation, segregation, and other
composition gradients. These compositional fluctuations may act as dominant active surface
sites with respect to corrosion.
CONCLUSIONS
It can be concluded that crystallization of this amorphous alloy FeCr9P6C3Si,0.2 did not
considerably alter its excellent corrosion resistance as long as the alloy remained a single
phase solid solution. This suggests that structure may not be a dominant factor in
determining the corrosion resistance of this amorphous alloy. When the crystallization was
complete, the corrosion resistance of the alloy deteriorated significantly.
REFERENCES
1. M. Naka, K. Hashimoto and T. Masumoto, J. Japan. Inst. Metals 38, 1974, p. 835.
2. Y. Waseda and K.T. Aust. J. Mater. Sci. 16, 1981, 2337.
3. R.B. Diegle, N.R. Sorensen, T. Tsuru and R.M. Latanision, in Treatise on Materials
Science and Technology (Edited by J. Scully), Vol. 23, p. 63, Academic Press, London
(1983).
4. K. Hashimoto, in Amorphous Metallic Alloy (Edited by T.E. Luborsky), p.471,
Butterworth, London (1983).
5. M.D. Archer, C.C. Corke and B. H. Harji, Electrochim. Acta 32, 1987, p. 13
6. P.C. Searson, P.V. Nagarkar and R.M. Latanision, in Modern Aspects of Electrochemistry
(Edited by R.E. White, J.O. Bockris and B.E. Conway), No. 21, pp.121-161. Plenum
Press, New York (1990).
7. K. Hashimoto, M. Naka, K. Asami and T. Masumoto, Corros. Eng. 27, 1978, p. 279.
8. K. Asami, K. Hashimoto, T. Masumoto and S. Shimodaira, Corros. Sci. 16, 1976, p. 909.
9. K. Hashimoto, K. Asami, K. Asami, and T. Masumoto, Corros. Eng. 28, 1979, p. 271.
10. R.B. Diegle and D.M. Lineman, Interim Technical Report No. 0NR-00014-77-C-0488-3
to the Office of Naval Research.
11. M. Naka, K. Hashimoto and T. Masumoto, Corrosion 36, 1980, p. 679.
12. T. Masumoto and R. Maddin, Acta Metall. 19, 1971, p. 725.
13. K. Hashimoto, K. Asami and K. Teramoto, Corro. Sci. 19, 1979, p. 3
14. K. Hashimoto and K. Asami, Corros. Sci. 19, 1979, p. 251.
15. K. Hashimoto and K. Asami, Passivity of Metals, Proceedings, 4th Intern. Symp. on
Passivity of Metals, (Edited by R.P. Frankenthal and J. Kruger), the Electrochemical
Society, Princeton, New Jersey, p.749 (1978).
16. K. Sugimoto and Y. Sawada, Corros. Sci. 17, 1977, p. 425.
17. M.Naka, K. Asami, K. Hashimoto and T. Masumoto, Proceedings, 4th International
Conference on Titanium (1980).
447
ABSTRACT
Waterborne and high solids paints-VOC compliant paints are becoming more important in coating
specifications for environmental reasons. They contain between 0% and 35% organic solvents (VOC)
per litre, compared to standard paints, where VOC often contributes 60% or more. High solids paints,
such as low solvent epoxies, have been used successfully in, for example, submerged areas. However,
petrochemical installations are still often coated with standard paint types.
In recent years, official tests, practical demonstrations and case histories have shown that
waterborne and low solvent coating systems protect steel in aggressive environments on a par with
standard paints, especially in cases when high solid epoxy primers are combined with waterborne acrylic
top coats-the hybrid system.
Calculated per square meter applied and considering the longer maintenance free intervals, the cost
of high solids and hybrid systems is not excessive. Painting contractors and specifiers can thereby meet
upcoming VOC-legislation on sound economic and technical bases.
Key Words:
INTRODUCTION
For environmental reasons, coating specifiers and painting contractors are today
constrained to using low volatile organic content (VOC) coatings for an increasing number of
painting jobs. The low VOC coatings are paints with a reduced content of organic solvents, and
they are present in the market in the form of waterborne paints and coatings with high solids.
In less corrosive environments, the long-term performance of the low VOC coatings is now
recognized to be fine. Their performance is often even above that of comparable standard
coatings such as alkyd, acrylic and epoxy [1]. However, in corrosive environments, experience
especially with waterborne coatings, is still limited. Lately, though, the offshore market and
independent testing laboratories have shown that coating systems with low VOC and
waterborne paints are well suited for severe corrosive environments. These systems may reduce
VOC emission by 70% or more, and the cost on an applied-square-meter basis is not excessive.
Thus, the new coating technology is in full accordance with the principle of BATNEEC, the
Best Available Technology Not Entailing Excessive Cost, which is statutory for all
environmentally directed developments.
EFFECT OF VOC's
449
The VOC in paints are organic solvents, and solvents are necessary to facilitate production
and application. But once the paints are applied, solvents are only a nuisance. They are
inflammable, and have a negative influence both on man and nature. A predisposed painter's
long-term continuous exposure to organic solvents will have a negative effect on his
Respiratory system,
Nervous system,
Capacity for reproduction, and
Skin.
Various governments and civil councils have, therefore, introduced health and safety measures
to protect painters, such as the Control of Substances Hazardous to Health (COSHH)
regulations in force in the UK.
When organic solvents evaporate, they are decomposed by the ultraviolet radiation from
the sun. The decomposed molecules are highly reactive and easily form compounds with the
exhaust from automobiles and industrial air pollution. These chemical reaction products will
affect the local environment, and eventually cause smog and reduce metabolism in human
beings, animals, and plants.
In Europe and the USA, VOC emission is being addressed by various legislative measures,
e.g., organic solvents from painting processes by an European Union Directive [2] to be
implemented into a law. The directive requests a solvent management and reduction plan, and
sets limits on emissions, but it is aimed at the user of the paint, i.e., the painting shops.
Upcoming British and existing American laws address the solvent content in the paint itself.
The aim of both types of regulation is to reduce the overall VOC emissions. It is expected
that the actions laid down in the European Union Directive-once introduced-will reduce the
solvent emissions in European Union member states by 30% in 1999 (compared with 1985).
Paint manufacturers today have products in their assortment that can meet these
regulations, among which are the waterborne and the high solids (low VOC) products for the
protective coating of steel structures.
The user-the painting contractor-may address an emission directive by installing an
abatement system in his plant, but this could be a costly solution. A better way is to modify
working procedures and adjust the equipment to handle waterborne and/or high solids paints,
and to train the applicators accordingly.
COATING SYSTEMS WITH REDUCED SOLVENT EMISSIONS
The satisfactory performance of paint coatings for the protection of steel structures against
corrosion is determined by
Kronborg Nielsen
C2: Low
C3: Medium
C4: High
Interior
Inside, heated buildings with
neutral atmospheres, and relative
humidity below 60%, e.g., offices,
shops, schools and hotels.
Unheated buildings where
condensation may occur, e.g.,
depots and sports halls.
Production rooms with high
humidity and some air pollution,
e.g., food processing plants,
laundries, breweries, and dairies.
Chemical processing plants, and
boat yards over seawater.
-
Paint System
Dry Film
Thickness
Solvent
Emission
451
Number
(g/sqm)
(m)
66
Chlorinated rubber primer
60
66
Chlorinated rubber primer
60
72
C4 - 5
Acrylic intermediate
60
60
72
Acrylic Top Coat
240
276
Standard solvent-borne system
Ethyl zinc silicate primer
67
80
C4 - 16
Waterborne epoxy intermediate
5
60
60
5
Waterborne epoxy top coat
77
200
Hybrid system
13
High solids epoxy primer
80
13
C4 - 7
High solids epoxy intermediate
80
80
13
High solids epoxy top coat
240
39
High solids system
2
Waterborne zinc epoxy
40
3
Waterborne acrylic intermediate
60
0.5
C4 - 10
Waterborne acrylic top coat
50
50
0.5
Waterborne acrylic top coat
200.
6
Waterborne system
67
Ethyl zinc silicate primer
80
52
Epoxy intermediate
60
43
C5 - 10x 1)
Epoxy intermediate
50
50
40
Polyurethane top coat
240
175
Standard solvent-borne system
40
21
High solids zinc epoxy primer
150
24
C5M - 7x
High solids intermediate
50
0.5
Waterborne acrylic top coat 2)
Hybrid system
240
46
C5M - 3
High solids epoxy primer
24
150
150
24
High solids epoxy top coat
300
48
High solids systems
40
2
Waterborne zinc epoxy
70
6
Waterborne epoxy intermediate
70
6
C5M - 6x
Waterborne epoxy intermediate
60
0.6
Waterborne acrylic top coat 3)
Waterborne system
240
14
Corrosivity Categories:
C4: Industrial and coastal areas
(ISO/WD 12944-2)
C5M: Marine areas with high salinity and corrosive areas
All systems are claimed in ISO/CD#1 12944-5 to have an expected
medium durability in the respective corrosion categories.
Notes:
1). In ISO/CD#1 12944-5 this system is a 5 coat system
2). In ISO/CD#1 12944-5 the top coat is chlorinated rubber
3). In ISO/CD#1 12944-5 the top coat is polyurethane
452
Kronborg Nielsen
Figure 1. Solvent emission from coating systems for industrial and coastal areas
Figure 2. Solvent emission from coating systems for marine and aggressive areas
The paint systems mentioned are only examples of many possible combinations having the
same performance. However, a considerable decrease in emissions is possible when one of the
waterborne or high solids/low VOC systems is selected.
453
Mixing waterborne paint with thinners which results in clogging spray equipment.
Preventive action includes cleaning spraying equipment carefully with thinner followed
by fresh water before the waterborne paint is introduced.
Applying waterborne paint on cold steel and/or at low temperatures which results in
insufficient curing and poor resistance. Preventive action includes painting indoors in
ventilated, heated facilities (ambient temperatures of 5C are sufficient for waterborne
acrylics), or making covers with heating, if possible. If not possible, low VOC systems
should be used.
Exposing newly waterborne painted objects to frosty weather which results in the
cracking of coating films. Preventive action includes keeping coated objects away from
frost for at least 24 hours after the application of waterborne paints.
Using waterborne paint indoors in areas without ventilation which results in runners and
slow drying. Prevention action includes allowing sufficient ventilation to extract the
water liberated during the application; for 20 l of paint more than 10 l of water have to
be removed in the form of vapor. The ventilation requirement is at least 75 m3 air/l paint
at 20C and 50% relative humidity.
The above errors can be overcome by changing the painting procedures and by training the
applicators.
Performance
Paint manufacturers, specifiers and societies use a number of accelerated test methods to
predict the lifetime performance properties of coatings. In particular, the corrosion resistance of
coating systems is important. Some of the test methods used are
Kronborg Nielsen
In the prohesion chamber cyclic test, the coated panel is dried between the salt spray and
the ultraviolet radiation cycles. Thereby more reliable test results, i.e., results with correlations
to genuine exterior situations, are obtained.
Waterborne and low VOC coating systems have performed satisfactorily in a number of
accelerated cyclic tests in comparison with standard high solvent systems. The results have
been confirmed by exterior exposure.
PERFORMANCE IN CORROSION CATEGORY 4: INDUSTRIAL AND COASTAL
AREAS
Waterborne coatings have been tested and applied since 1984 on dry cargo containers for
carriage by sea, and the obtained experience has only been positive [1]. Today more than 3000
containers are in service, either with waterborne systems only (zinc epoxy/epoxy/acrylics), or
with a hybrid system made of solvent-borne (zinc) epoxy prime coat(s) followed by waterborne
acrylic top coats.
In Kuwait, the Kuwait Institute for Scientific Research has compared 11 coating systems in
two laboratory cyclic tests and at five exposure sites in Kuwait [5]. The sites selected for the
outdoor panel exposure had different environmental parameters of the industrial area and were
at varying distances from the Arabian Gulf. Inorganic zinc silicate (IOZ)/epoxy/polyurethane
systems and waterborne acrylic systems performed better than other systems, both in the
laboratory (3000-hour test) and at the sites (two year exposure).
Also in the Gulf area, the petrochemical market has discovered that the exterior of storage
tanks can be advantageously finished with an acrylic waterborne top coat. The traditional
system of zinc epoxy/epoxy/polyurethane is occasionally being replaced by zinc epoxy/high
solids epoxy/waterborne acrylic on tank farms. Although the gloss retention of the
polyurethane top coat is slightly superior, the new system has three distinct advantages:
Cost. Calculated per square meter, the IOZ/high solids epoxy/waterborne coating
system is 10-15% cheaper than an IOZ/epoxy/polyurethane system (dft 225 m).
British Gas' gasholders. Many of the gasholders seen near the major cities are now
maintained with waterborne coatings with excellent performance results.
455
waterborne coatings has several advantages over solvent-borne systems. First there
is no fire risk. Fire and explosion risks from paint are eliminated, during both
application and storage. Additionally, waterborne paints have low flame spread
characteristics once they are applied. Second, no thinner is required, water is the
diluent and is also used for the cleaning of application tools. Third, there is less odor
and less inconvenience. Waterborne coatings are popular for use indoors because
they allow other trades to work in the immediate vicinity, so painters do not have to
work night shifts. Fourth, waterborne coatings have good protective properties. The
performance of the coatings in respect to gloss and color retention, and protection is
highly satisfactory.
The number of RFA-ships using waterborne coatings is now nearly 25.
Figure 3. Solvent emission from coating systems for marine and aggressive areas
CORROSION CATEGORY 5: MARINE AND AGGRESSIVE AREAS
In 1992, the three major Norwegian petrochemical and offshore operators, Statoil, Saga
Petroleum and Norsk Hydro, introduced a prequalification test for coatings used on offshore
structures. The prequalification test [7] included, among other things, coating systems for
structural steel, exteriors of vessels and tanks, piping (not insulated), valves, and steel in
noncorrosive areas; all decks; and submerged steel.
The tests used for the prequalification and the acceptance criteria are listed in Table 3.
High solids/low VOC coating types like reinforced polyester and solvent-free epoxies have
been specified for offshore decks and have performed very satisfactorily over the years. The
testing confirmed their good performance. Similarly, the good experience with solvent-free or
low solvent epoxies in submerged areas has been verified.
456
Kronborg Nielsen
Method
ISO 7253
Duration
8000 h
Acceptance Criteria
Max disbonding 5 mm
(ISO 4628).
Blistering: not visible
(ISO 4628).
Remarks
Cathodic
disbonding
ISO 6270
8000 h
ASTM 623-89
2000 h
ASTM G8
28 d
Max disbonding 5 mm
Overcoatable
without
mechanical
pretreatment.
Only for non
submerged
coatings.
Only for
submerged
coatings.
HB epoxy, LTC*
165 m
WBorne acrylic
50 m
Total
300 m
Solvent emission: 217 g/m2
Paint price/m2, index: 83
In the 1990s, with greater focus on environmental issues, systems employing low VOC
products are becoming more important. Also the isocyanate curing agent in the polyurethanes is
being put under surveillance (officially and unofficially) in, for example, Great Britain and
Norway. Therefore, the IOZ/HB epoxy/WB acrylic described in Table 4 is a step towards top
side systems formulated with respect for environmental concerns both for the applicator and his
surroundings. It is worth noticing that the IOZ/HB epoxy/WB acrylic top-coat system has both
the lowest emission and the lowest cost.
Since 1992 a major Norwegian offshore operator, Amoco Norway, has employed this zinc
silicate/HB epoxy (amide type)/waterborne acrylic system both for offshore maintenance
painting and for new construction in manufacturing units. Occasionally, zinc-rich epoxies are
also used as prime coats. The operator decided to change to the low VOC system after a
thorough evaluation of the anticorrosive properties, and the reduced solvent, low molecular
amine and isocyanate exposure of the applicators. After the initial adjustment of procedures, the
result has been very positive from environmental, operational, and economical points of view
[8].
The low VOC, high solids epoxy mastic has for a long time been used for maintenance on
ships' topsides, superstructures and exposed steel structures, especially on power-tool cleaned
surfaces. They have replaced traditional chlorinated rubber and alkyd systems, and their
success is again due to the possibility of applying high film systems in a few coats; a
comparably lower cost per square meter when applied at the same dry film thickness with
recognized better protective performance [9]. The epoxy mastic may be top coated with
waterborne acrylic coatings to obtain gloss and better color retention while keeping the solvent
emission down.
An exceptional coating test object is situated on the Thames near the Tower Bridge: The
HMS Belfast. This World War II warship was painted with waterborne acrylics in 1993, and
the surface condition is excellent [10,11].
SUMMARY
Legislation is gradually forcing painting contractors and shipyards to employ paint systems
with low solvent emissions (i.e., low VOC). Among the low VOC paints on the market are high
solids epoxies and waterborne acrylics. The introduction of these coatings in less aggressive
environments is already in place. However, the use of waterborne coatings in particular has
been more cautious in highly corrosive environments, e.g., ships' topsides, petrochemical
installations, and offshore. The reluctance is mainly originating from limited experience with
their long-term performance.
However, official tests, practical demonstrations and case histories in aggressive areas have
458
Kronborg Nielsen
now shown that waterborne acrylic finishes combined with high solids/low VOC prime coats
are as fully resistant to corrosion as any alternative. Similarly, high solids epoxies,
polyurethanes and polyesters have also demonstrated their performance in corrosive
environments. Therefore, on sound economic and environmental bases, coating contractors,
specifiers and shipyards can meet the upcoming VOC legislation with environmentally
acceptable and resistant coating systems.
REFERENCES
1. S. Nysteen, Surface Coatings International, July 1994, p. 311.
2. European Union, Proposal for a council directive (EEC) on the limitations of the emissions
of organic compounds due to the use of organic solvents in certain processes and industrial
installations, April 1994.
3. ISO 12944. Secretariat of ISO/TC 35/SC 14, N76, N37 and N94.
4. J. Andrews et al., Cleveland Society for Coatings Technology Technical Committee, Journal
of Coatings Technology, October 1994, p. 49.
5. J. Carew et al., Materials Performance, December 1994, p. 24.
6. I. Walker, Petroleum Review, November 1994, p. 520.
7. Statoil, Norway, Specification for purchase, Surface Preparation and Protective Coating
Doc. no. R-SP-630, 1992.
8. T.M. Ege and H. Erikstein, Maling offshore: Bruk av vanntynnbare toppstr ksmalinger i
Nordsj en. Hvilke krav og erfaringer har man? (Painting offshore: Demands and experience
with waterborne top coats in the North Sea), Overflatedagar 95, Paper A-5, Oslo, Norway,
Teknologisk Institutt, November 1995 (In Norwegian).
9. P.K. Nielsen, J.H. Hansen, Ecology and economy in the development and use of heavy-duty
protective coatings for Steel, Corrosion Asia/94, Paper No. 1130, Singapore, National
Association of Corrosion Engineers, September 1994.
10. Lloyds List, 29 September 1994, p. 14.
11. D. Woodyard, Lloyds List, 19 April 1991, p. 5.
459
ABSTRACT
Present law stipulations concerning environmental protection require that modern film-forming
products should produce an as little pollution as possible. To achieve this, water should be used as a
thinner to produce waterborne anticorrosive paints for metal and emulsion paints for anticorrosive
protection of concrete. As concerns waterborne products, ICEPALV is researching products applied
by electrophoresis, and offering licenses for anaphoretic primers; and has developed air-drying
waterborne primers and paints, based on epoxy and alkyd resins. As concerns emulsion paints,
ICEPALV has researched and developed acrylic, acrylo-styrene, vinyl-acrylic, and vinylic as well as
decorative plasters for concrete protection. ICEPALV is also researching anticorrosive emulsion
paints, based on meth(acrylic) copolymer latices with vinyl esters of heavily monocarboxylic acid
containing 10 carbon atoms (VeoVa 10).
Key Words: Metal, concrete, anticorrosive protection, waterborne products, emulsion paints
INTRODUCTION
Since 1980, the ICEPALV research in the field of film-forming materials has been
directed by the need to protect the environment. The use of water as a thinner in the
development of waterborne products and emulsion paints is one of the ways to achieve this
purpose.
Water Thinnable Products
ICEPALV is concerned with developing this important group of products used especially
in the building machines industries (i.e., bodies, cases, wheels and other accessories), but also
in other industries, as for example, for the anticorrosive protection of metallic buildings.
As concerns the application of these products, they are used simultaneously in both older
application systems (i.e., immersion, flow-coating, and spraying) as well as in newer ones
(i.e., anionic and cationic electrodeposition, and autophoresis) [1]. The main waterborne
products developed by ICEPALV in Romania are presented in Table 1.
Emulsion Paints
Concrete corrosion is a complex physicochemical process. Corrosion may be spoken
about as an electrochemical phenomenon only in the case of reinforced concrete; otherwise, it
is only about the support isolation from the corrosive medium. Therefore, nowadays
especially, the outdoor painting of buildings is a necessity, having both an aesthetic and an
461
anticorrosive protection function. Emulsion paints are more and more often used for these
purposes, and their advantages are well known.
A whole series of putties, primers, decorative plaster and paints based on acrylic, acrylostyrene, acrylo-vinyl, vinyl, etc. latices for concrete protection have been developed and
launched on the market by ICEPALV. Among these the most important are those mentioned
in Table 2.
Table 1. The Main Waterborne Products Developed by ICEPALV in Romania
Product
Series
Grey primer
Brown primer
Grey primer
Grey, red A-B primer
Colourless, black,
khaki primer
Grey anticorrosive
primer
Dark-black primer
7100
7101
7003
7004
7004
alkyd-phenol
alkyd-phenol
alkyd-phenol
alkyd-phenol
alkyd-phenol
Application
Method
flow-coating
spraying
immersion
electrophoresis
electrophoresis
7003
epoxy-ester
immersion
7206
acrylic
flow-coating,
immersion
7005
polybutadiene electrophoresis
7210
acrylic
Anticorrosive grey
primer
Black primer
Binder
Recommended Uses
Building-machines industry
Building-machines industry
Building-machines industry
Automotives industry
Building-machines industry
Automotives and
electrodomestic industry
The protection of gasoline
tanks and of the other accessories in the automotive
industry
Automotives industry
immersion,
Phosphatized plates
spraying
protection
Air drying primer
7352 waterborne
by brush, roller Building-machines industry
alkyd
or spraying
Air drying primer
7702 waterborne
by brush, roller Building-machines industry
alkyd
or spraying
Air drying primer
7752 waterborne
by brush, roller Building-machines industry
alkyd
or spraying
Beige primer
7385 epoxy-ester
electrophoresis Automotives industry
Black primer
7325 epoxy-ester
electrophoresis Automotives industry
Air-drying paint
7351 epoxy
by brush, roller Building-machines industry
or spraying
Air-drying paint
7751 epoxy
by brush, roller Building-machines industry
or spraying
Colourless,
8771 vinyl-polyby brush or roller Protection of paint spray
removable varnish
acetate latex
booth glass surfaces
White, removable
8772 vinyl-polyby brush or roller Protection of paint spray
paint
acetate latex
booth metal surfaces
Table 2. The Main Emulsion Products Developed by ICEPALV in Romania
462
Serban et al.
Product
Soaking primer
Series
8440
8640
LUCICRIL-half-glossy
paint for outdoors
DASIROM-half-matt
paint for outdoors
Half-matt paint for
outdoors
VEPAROM-matt paint
for indoors
VEPATIM-matt paint
for indoors
Matt paint for indoors
8513
8213
STROP- decorative
plaster
8411
8415
8427
8430
8630
8426
Latex
Acrylo-styrene
hydrosol
Recommended Uses
To fill in the pores and to
increase adherence (concrete,
masonry)
Vinyl-maleic
To putty the concrete before
copolymer
finishing
Pure acrylic
Outdoor finishing of buildings
copolymer
(wood, concrete, masonry)
Acrylo-styrene
Outdoor finishing of buildings
copolymer
(concrete, masonry)
Acrylo-styrene-maleic Outdoor finishing of buildings
copolymer
(concrete, masonry)
Acrylo-styrene
Indoor finishing of buildings
copolymer
(concrete, masonry)
Vinyl-maleic
Indoor finishing of buildings
copolymer
(concrete, masonry)
Acrylo-styrene-maleic Indoor finishing of buildings
copolymer
(concrete, masonry)
Vinyl-polyacetate
Indoor finishing of buildings
homopolymer
(concrete, masonry)
Acrylo-styrene
Decorative finishings for outdoor
copolymer
buildings (concrete, masonry)
463
OH
unsaturated fatty
OH
acids
OH
OH
OH
245 C
catalyst NaOH
COOH
HOOC
COO
CH
OOC
CH
HOOC
OH
120-150C
OH
OH
HOOC
O OC
HOOC
COO
Epoxy resin
M=900-1000
COOH
HOOC
COO
COOH
COOH
HOOC
Tricarboxyl adduct
COOH
COO
The tricarboxyl adduct is previously achieved from fatty acids, maleic anhydride and
water, according to the reaction:
COOH
COOH
CH
COOH
HC
CH2
COOH
O
H2O
O
O
HC
HC
COOH
HOOC
Unsaturated
fatty acids
125C
Succinic adduct
220C
COOH
HC
HC
CH
COOH
CH
COOH
Diels-Alder adduct
464
Serban et al.
-20
-30
-40
-50
-60
-70
-80
-90
-100
0
8 10 12 14 16 18 20 22 24
Time (hours)
140 - 220
max. 20
60 -360
25-28
for 30 minutes at a temperature of
From Fig. 2, the variation of film thickness according to application time, at the
application voltage (180 V), as well as at breakdown voltage (50 V) can be seen.
Film Characterization
465
Between 20 and 30 m films are achieved with a uniform appearance, free of surface
faults (i.e., pinholing, cratering). The mechanical characteristics are very good:
1
4 min.
30 min.
1
The films corresponded from the point of view of corrosion resistance, so:
192
6
4
192
absent
21
absent
The throwing power was determined on 24-cm samples, and their values are presented in Fig.
3.
In conclusion, from the short presentation of the epoxy-ester electrophoretic primer
series 7301, it may be noticed that this product, used for the anticorrosive protection of some
parts and units in the automotive industry, corresponds to the present requirements of the
Romanian industry.
35
Thickness (um)
30
25
20
15
50 V (max. 25 minutes)
10
10
15
20
25
30
Time (minutes)
466
Serban et al.
30
20
10
0
0
12
15
18
21
24
Distance (cm)
10 20 30 40 50 60 70 80 90 100
Figure 3. Evolution of throwing power with distance
Anticorrosive Primer Paints Based on VEOVA 10 (Meth) Acrylate Latices
ICEPALV has been researching anticorrosive primer paints based on VeoVa 10
(meth)acrylate latices. Various studies [2,3] demonstrated that the incorporation of VeoVa
monomers in (meth)acrylic copolymers improves the chemical and, especially, the water
resistance of the latex films. The bulky aliphatic entity gives the copolymer a high
hydrofobicity, an excellent UV resistance and also a good alkali resistance by protecting it
from saponification [4].
EXPERIMENTAL PROCEDURE
The latices were obtained by the copolymerisation of VeoVa 10 and 2 ethylhexyl
acrylate (which also contributes to good water repellency) as soft monomers with
methylmethacrylate as a hard monomer.
Performing the polymerization essentially in the absence of colloids and in the presence
of a minimum quantity of surfactant with phosphate groups (e.g., organic ester phosphate:
REWOPHAT E 1027 - REWO, Germany), whilst at the same time carefully adding the paint
formulation additives (i.e., coalescing agents, thickener, and dispersant) and pigments and
mineral fillers, films possessing intrinsically good barrier properties can be achieved. The
best results were obtained with monomer compositions falling in the shaded area of Fig. 4.
In the primer paint formulations zinc, phosphate was introduced. It proved to be an
anticorrosive and nontoxic pigment. It appears to pack in the film in a manner which presents
a high resistance to the passage of water molecules and salts and an anticorrosive efficiency
similar to zinc chromate, in long-term exposure tests. The primer paints were formulated at
two different PVC: 20% and 30%, at basic pH. The evolution of the viscosities was
essentially unchanged after 8 months of storage, thus demonstrating the good stability of
these primers. They are being kept under observation.
467
468
Serban et al.
Adhesion
10
6
PVC= 20 %
4
PVC= 30 %
2
0
20
30
40
50
60
70
80
Erichsen
elasticity
(mm)
Tg = 15 oC; 0 - bad,
10 - excellent
Figure 5. Influence of VeoVa 10
concentration
on primer paint adhesion
10
Water
spot
rezistence
8
7
6
6
5
PVC= 20 %
4
PVC= 30 %
2
3
0
2
20
30
40
50
60
70
Tg = 15C
Figure 6. Influence of VeoVa 10
concentration on primer paint
elasticity on metal
80
20
30
40
50
60
70
80
469
W a te r v a p o u r
p e rm e a b ility
(g / 0 .1 m m /
100cm / day)
P VC = 2 0 %
P VC = 3 0 %
1 .6
1 .2
0 .8
0 .4
0
10
20
30
40
50
60
70
Ve o Va 1 0 c o n c e n tra tio n (% )
Tg = 15 oC
Figure 8. The effect of VeoVa 10 concentration on the
water vapour permeability of primer paints
CONCLUSIONS
ICPALV is concerned with developing some new electrophoretic products of the latest
generation (i.e., cataphoresis) which together with other measures (e.g., the use of galvanized
sheet, waxes and protection products, and good and severe services) will increase the storage
life of the new types of automotive and metallic surfaces, in general.
As concerns emulsion paints, ICEPALV is concerned with developing new products
with higher durability for concrete protection and new anticorrosive primer and emulsion
paints for metal protection.
REFERENCES
1.
2.
3.
4.
5.
470
ABSTRACT
The present study investigates the disbonding phenomenon according to the British Gas Method
PS/CW6 and the ASTM-G8 standard. This investigation showed that the best protection for
disbonded buried pipelines under cathodic protection would be achieved if the applied potential was
kept -950 to -1000 mV with respect to the Cu/CuSO4 half-cell rather than the usual value of -850 mV
(Cu/CuSO4) which is currently used.
Key Words: Pipeline, coating, soil, disbonding, cathodic protection
INTRODUCTION
Underground corrosion of buried steel is a major problem in the oil and gas industries
[1]. A good practice in modern pipeline corrosion control work comprises the use of good
coatings, in combination with cathodic protection as the main lines of defence [2], and better
current distribution is accomplished by using an insulating coating [3]. Therefore, attempts to
control pipeline corrosion rely on the use of coating materials with the reasoning that if the
pipeline metal is isolated from contact with the scratches from soil, no corrosion could occur.
However, the insulating coatings must be free of any defects such as scratches or pinholes.
Pitting associated with such defects in the coating, i.e., Holidays, and subsequent disbonding
have been observed on pipelines which are nominally cathodically protected [4,5].
Fessler [6] suggested that stress corrosion cracking on buried, coated pipeline tends to
occur under disbonded coatings near small pinholes or holidays. It was deduced that a
disbonded coating acted as a shield to the cathodic protection current and caused potential
gradients under the coatings [7]. Aqueous displacement as a possible mechanism of the
cathodic disbondment of protective organic coatings was suggested by Evans [8] in terms of
the ability of an alkaline solution to creep over the metal surface and displace the organic
coating. Bolger and Micheals [9] argued that displacement of coatings from a metals surface
is promoted by pH values far removed from the isoelectric point of the surface oxide so that
the oxide has a greater affinity for the water than for the organic materials.
EXPERIMENTAL PROCEDURE
471
Soil Analysis
Since the types of soil differ along the buried pipeline, four types of soil were taken from
different sites as follows:
CO3
HCO3
SO4
Cl
Na
Mg
Ec
Ca
pH
Soil
Type
(mmhos/cm)
33
146.5
71
1036
15.5
18.5
68
516
2.15
7.56
26
148.2
106.5
1728
75.5
20.5
49.5
560
2.70
7.43
37
341.6
461.5
960
980
17
113.7
320
4.87
7.79
6.4
1753
770.5
1536
1006.5
105
121.5
528
11.52
8.44
Ec (mmhos/cm)
pH
Soil
CO3
HCO3
Cl
SO4
Na
Mg
Ca
Type
188
Tested Material
472
2912.5
4467
1398.6
868
754
540
28.42
acidic
Pakshir
Test specimens were cut and flattened, and then they were stamped with an identifying
number from the existing new pipeline used in the Shiraz gas industry according to ASTMA53 grade B having the following composition:
0.30% C, 1.20 % Mn, 0.05 % P, 0.06 % S
Each specimen was hand brushed with a wire brush, and soaked in a solvent to remove
the cutting oil.
Test Procedure
In order to investigate the potential gradient under the disbonded coatings
experimentally, special suitable cells were constructed ( Fig. 1).
Steel samples 200 x 160 mm were coated with a cold tape used in Shiraz gas industries
called NITO. The tape consisted of a polyethelene backing and a thermoplastic adhesive.
For better adhesion, NITO primer was used. The technique for measuring the potential under
the disbonded coatings was based on British gas method PS/CW6 in which backside
electrodes were prepared by inserting a 500 mm length of a 5 mm outside diameter PVC
tubing filled with agar and KCI. They were then filled with a sintered glass plug through four
predrilled holes in the back of the steel plate. The holes were positioned in a line so as to
give eight positions 5 mm apart at distances from 10 to 40 mm from the center of the holiday.
solution. A platinum wire was used as the counter electrode. The steel plate was connected
to a voltage supply by a wire tapped into it and insulated. The holiday potentials were
controlled by a voltage regulator. The voltage was measured using a reference electrode and
a digital multimeter. The holiday potentials were set at values of -780, -920 and - 1200 mV
(SCE).
In order to extract solutions from beneath the disbonded coating, a piece of polyethylene
tubing was inserted through the steel in a fation similar to that used for the electrodes. A
thinner length of tubing was then be inserted through the first hole to allow solution to be
extracted with a syringe.
The pH of the extracted solution was measured using a pH paper, and the chloride
solution was measured using a Ag/AgCl microprobe. However, at distances further than 10
cm from the holiday, little success was achieved in extracting any crevice solution due to the
thinness of the layer of electrolyte. Along the crevice, most of this liquid was absorbed into
the adhesive. In this region, the pH values of the solution were measured directly from
moisture that was found on the steel underneath the backing after the coating had been
removed.
Polarization Study
In order to obtain the potential-pH diagram, a polarization study was carried out.
Specimens 1 x 1 cm in dimensions were cut from the original pipe and mounted in a
specimen holder so that 1 cm2 of the steel was exposed, and the polished specimen was
placed in a corrosion cell with a platinum counter electrode and a lugging probe. The cell
was filled with an already made. simulated solution of pH 8.44. To simulate the alkaline
environments found beneath the disbonded coating, the pH of the solution was increased by
adding various amounts of NaOH.
RESULTS AND DISCUSSION
Using a backside electrode as a special technique, the potentials under the disbonded
coating were measured as a function of distance away from the holiday (Figs. 2 and 3). Also,
using a catheter arrangement, the pH and the concentration of the chloride solution under the
disbonded coating could be determined (Tables 3 and 4).
In this investigation, three holiday potentials were chosen: the potential of -780 mV
(SCE) was chosen since it represents the minimum cathodic current density in order to
polarize the pipe to 850 mV Cu/CuSO4, and the holiday potential of -1500 mV (SCE) since it
represents the overprotection potential. A test temperature of 40C was used to simulate the
conditions of the hottest part of the soil. As can be seen from Tables 3 and 4, the
concentration of chloride ions in the crevice did not vary significantly from the bulk solution,
and also, the concentration of chloride ions in the crevice was not a function of the holiday
potential.
Since the solution pH beneath the disbonded coating was thought to ncrease, polarization
tests were carried out in the alkaline range of pH. Two distinct points can be seen in Figs. 4
and 5: the interaction of polarization current with the potential axis. i.e., where the current
density was zero and was representative of the corrosion potential (Ecorr); and the start of the
decrease in current density while the potential increased and was representative of the
474
Pakshir
Table 3. Experimental Results for Alkaline-Saline Soil and the Holiday Potentials
of -0.780, -0.920 and -1.5 V
Cl
(ppm)
Crevice
Tip/pH
Time
(hour)
805.2
798.5
752.1
794.3
10.48
11.02
10.63
10.83
40
-0.604
-0.603
-0.604
-0.707
30
-0.606
-0.605
-0.709
-0.714
20
-0.603
-0.710
-0.716
-0.719
10
-0.715
-0.724
-0.731
-0.736
0
-0.780
-0.780
-0.780
-0.780
513
862
1103
1223
791
812.3
783.4
800.8
751.5
818.1
759.5
791.2
11.08
10.54
10.96
10.61
10.41
10.52
11.02
10.75
-0.611
-0.611
-0.610
-0.673
-0.612
-0.611
-0.610
-0.743
-0.608
-0.607
-0.674
-0.680
-0.605
-0.607
-0.722
-0.747
-0.616
-0.675
-0.685
-0.691
-0.609
-0.717
-0.785
-0.828
-0.704
-0.728
-0.751
-0.778
-0.725
-0.823
-0.907
-0.991
-0.920
-0.920
-0.920
-0.920
-1.500
-1.500
-1.500
-1.500
363
605
770
863
143
325
297
335
Holiday
Potential
(Volt)
-0.780
-0.920
-1.580
Table 4. Experimental Results for an Acidic-Type Soil and the Holiday Potential
of -0.780, -0.920 and -1.5 V (cm/CuSO4)
475
Cl
(ppm)
Crevice
Tip/pH
2850.5
2920.2
2860.4
2898.7
29.20.2
2870.8
2932.7
2946.5
2873.6
2950.2
2873.8
2932.6
10.33
10.28
10.47
10.86
10.52
10.63
10.21
10.44
10.73
10.96
10.85
10.91
40
-0.605
-0.605
-0.604
-0.655
-0.600
-0.601
-0.600
-0.628
-0.611
-0.612
-0.611
-0.686
30
-0.609
-0.607
-0.665
-0.673
-0.603
-0.604
-0.632
-0.641
-0.608
-0.608
-0.687
-0.701
476
Time
(hour)
10
-0.690
-0.704
-0.711
-0.715
-0.680
-0.708
-0.729
-0.744
-0.701
-0.807
-0.891
-0.945
0
-0.780
-0.780
-0.780
-0.780
-0.940
-0.920
-0.920
-0.920
-1.500
-1.500
-1.500
-1.500.
623
1038
1320
1482
421
719
911
1016
215
359
455
505
Holiday
Potential
(Volt)
-0.780
-0.920
-1.500
Pakshir
As can be seen from Figs. 4 and 5, a significant shift of the crevice potentials to more
positive values occurred as the distance from the holiday along the crevice increased. Also,
the largest potential drop occurred near the holiday. The potential gradient appeared to
decrease at distances further along the holiday. The major differences between the three
potentials applied is the disbondment time, i.e., as the holiday potential became negative, the
disbondment time decreased. For example, for an alkaline-saline soil, it took two months to
disbond the coating at a holiday potential of -780 mV (SCE), while at a potential of -1500
mV (SCE), it only took 14 days. The crevice tip potential for the three applied holiday
potentials varied between -673 and -734 mV (SCE), and the pH of the tip of the crevice
varied between 10.41 and 11.08. Therefore, neither the crevice potential nor the crevice tip
pH were a function of the applied holiday potentials.
Polarization tests enabled an experimental potential-pH diagram to be constructed for the
steel exposed to conditions which simulated those formed beneath the disbonded coatings
(Figs. 6 and 7). Superimposed on these diagrams are the crevice tip environments which
were determined from the corresponding cathodic disbondment test. Hence, if the -crevicetip potential lay between -673 and -734 mV (SCE), and the crevice-tip pH lay between 10.41
and 11.08, then according to Fig. 6, only a small part of the blackened area lay within the
general corrosion area, whereas a large part of it was in the complete passivation area.
Hence, maintaining the steel exposed along the crevice in a passive state depended only on a
continued high PH. Consequently, the condition of the crevice tip determined the corrosion
behavior of the metal beneath the disbonded coating. In another words, by knowing the
condition of the crevice tip on the potential-pH diagram, one can estimate the corrosion and
noncorrosion condition beneath the disbonded coating.
477
Figures 8 and 9 show that the condition required for the occurrence of corrosion beneath
a disbonded coating is for the crevice potentials to be within the general corrosion range of
about -695 to -845 mV (SCE). Therefore, as cathodic disbondment occurs, the crevice
potentials place the steel at some distance along the crevice into a region of general corrosion.
This can be seen by the surface morphology of the specimens after the disbonding test ( Figs.
10-15).
As can be seen from Fig. 10, all the disbonded surfaces were in the region of general
corrosion, but when the holiday potential was kept at -920 mV (SCE), the first 5 mm of the
disbonded surface was in the immunity region, from 5 to 20 mm was in the general corrosion
region and at distances > 20 mm from the holiday, the surface was in the passive state. These
situations can also be predicted by Figs. 8 and 9.
478
Pakshir
Figures 10-12. Surface morphology after disbondment for alkaline-saline type soil at various
holiday potentials
479
Figures 13-15. Surface morphology after disbondment for acidic type soil at various holiday
potentials
From Fig. 11, it can be seen that in the first 20 mm from the holiday, the disbonded
surface was covered by an oxide layer which represents the general corrosion and suggests
that the metal underneath the disbonded coating was in the passive state. When the holiday
potential was kept at 1500 mV (SCE), the potential-pH diagram predicted that up to 18 mm of
the disbonded surface would be immune to corrosion, and then would show general
corrosion. In Fig. 9, the curve predicts the regions of corrosion, passivation and immunity
under the disbonded coating, i.e., for an acidic soil it predicts that at a holiday potential of 780 mV (SCE), the surface would be in the general corrosion region, at a holiday potential of
480
Pakshir
-920 mV (SCE), the first 4 mm of the disbonded surface would be in the immunity region,
and between 4 and 20 mm, the metal would be in the general corrosion region and then in the
passivated region. This prediction can be shown by the surface morphology examination
shown in Figs. 13, 14, and 15.
CONCLUSIONS
For an alkaline-saline soil, the occurrence of corrosion beneath a disbonded coating
requires that the crevice potentials be within the general corrosion range of -695 to -845 mV
(SCE). The crevice potentials for a holiday potential of -920 mV lie solely within the perfect
passivation region beyond a distance of about 5 mm from the holiday. However, during the
growth of the disbondment area and the consequent movement of the crevice potentials to
their final values, the crevice potentials must be in the region of general corrosion. For the
crevice potential obtained for a holiday potential of -1500 mV (SCE), the potentials must lie
within the general corrosion region from about 18 to 28 mm from the holiday.
Important conclusions which can be drawn from this investigation is that the applied
potential of -780 mV (SCE) is not satisfactory, and a holiday potential of -1500 mV (SCE) is
not representative of an instantaneous off potential which suggests that overprotection is
undesirable. However, when the applied potential is -920 mV (SCE), only small parts around
the holiday are in the general corrosion region while the rest of the surface is in the protected
state. Therefore, this potential is recommended for buried pipeline.
Also from Figs. 16 and 17, it can be concluded that for both types of soil, the disbonded
mechanisms follow similar patterns, although the disbonding rate is much slower for an
acidic soil.
REFERENCES
481
2.
3.
4.
5.
6.
7.
8.
9.
482
ABSTRACT
The synergistic effect existing between and among the sodium salt of ethyl phosphonic acid
(EPA), Zn2+, and molybdate on the inhibition of corrosion of mild steel in a neutral aqueous
environment containing 60 ppm Cl- was evaluated by the classical weight-loss method. The
formulation consisting of 300 ppm EPA, 300 ppm MoO42- and 50 ppm Zn2+ had 99% inhibition
efficiency. The mechanistic aspects of corrosion inhibition are discussed, in a holistic way, based on
the results obtained from a potentiostatic polarization study, the x-ray diffraction (XRD) technique,
and UV-visible diffused reflectance, FTIR and luminescence spectra.
Key Words: Mild steel, neutral environment, corrosion inhibition, synergistic effect, ethyl
phosphonate-zinc-molybdate
INTRODUCTION
Molybdates are among the most broadly applied inhibitors, chiefly because of their
efficacy towards both ferrous and nonferrous metals and their very low order of toxicity [1].
Molybdate can be used as corrosion inhibitor alone or in combination with other synergists
like nitrite [2], metallic cations like Ni2+, Mn2+, Zn2+ [3], azoles like benzotriazole and
tolyltriazole [4], chromate [5], amine phosphonates [6], inorganic phosphates [7], citrate and
calcium [8]. Even though several papers [1-14] have discussed the use of molybdate as
corrosion inhibitor, the mechanistic aspects of corrosion inhibition have not been studied in
detail. The present work evaluates the synergistic effect existing between and among
molybdate, Zn2+ and ethyl phosphonate by the weight-loss method. The mechanistic aspects
of corrosion inhibition were studied, in a holistic way, based on the results obtained from a
potentiostatic polarization study, the x-ray diffraction (XRD) technique, UV-visible diffused
reflectance, FTIR and luminescence spectra.
EXPERIMENTAL PROCEDURE
483
484
Rajendran et al.
Table 1. Corrosion Rates of Mild Steel in a Neutral Aqueous Environment (Cl- = 60 ppm) in
the Absence and Presence of Inhibitors, and the Inhibition Efficiencies Obtained by
the Weight-Loss Method
2+
SI. EPA
Zn
MoO4
No. (ppm)
(ppm)
(ppm)
1
2
300
3
50
4
300
50
5
300
50
50
6
300
50
100
7
300
50
200
8
300
50
300
9
300
300
10
50
300
11
300
Inhibitor system: EPA + Zn2+ + MoO42-
2-
Corrosion
rate
(mdd)
15.54
15.39
19.11
6.22
13.98
11.66
9.32
0.16
0.16
1.58
3.11
Inhibition
Efficiency
(%)
1
-23
60
10
25
40
99
99
90
80
It is evident from Table 1 that ethyl phosphonic acid (EPA) by itself is not a good
inhibitor and Zn2+ is corrosive. Interestingly the formulation consisting of 300 ppm EPA and
50 ppm Zn2+ had a 60% inhibition efficiency. This indicates the synergistic effect between
EPA and Zn2+. When various concentrations of molybdate were added to the above system,
the inhibition efficiency increased at 300 ppm MoO42-. The formulation consisting of 300
ppm EPA, 50 ppm Zn2+ and 300 ppm MoO42- had a 99% efficiency. It was found that the
formulations consisting of 300 ppm EPA and 300 ppm MoO42-, and also MoO42- (300ppm)Zn2+ (50 ppm) showed a synergistic effect.
Analysis of the Potentiostatic Polarization Curves
The potentiostatic polarization curves of mild steel immersed in various environments
are given in Fig. 1. It is observed that, when molybdate was added to chloride or EPA or Zn2+
or EPA-Zn2+, the corrosion potential shifted to the anodic side. The formulation consisting of
300 ppm EPA, 300 ppm MoO42- and 50 ppm Zn2+ shifted the corrosion potential to -390 mV
vs. SCE. This indicates that this formulation acts as a mixed inhibitor. This is further
supported by the fact that the anodic and cathodic Tafel slopes shifted almost equally (28
mV/decade).
Analysis of the FTIR Spectra
The FTIR spectrum of pure EPA (KBr) is given in Fig. 2a. The FTIR spectrum (by the
multiple internal reflection (MIR) technique) of the film formed on the surface of the metal
specimen immersed in an environment consisting of 60 ppm Cl-, 300 ppm MoO42- and 300
ppm EPA is given in Fig. 2b. It is found that the P-O stretching frequency [15-17] of the
phosphonic acid decreased from 1071.7 cm-1 to 1018.6 cm-1. This suggests that the oxygen
atom of the phosphonic acid coordinated to Fe2+ on the metal surface [18,19].
485
The FTIR spectrum (MIR) of the film due to the environment consisting of 60 ppm Cl-,
300 ppm EPA, 300 ppm MoO42- and 50 ppm Zn2+ reveals that the P-O stretching frequency
decreased from 1071.7 cm-1 to 1018.4 cm-1. This suggests that in this case also, the oxygen
atom of the phosphonic acid coordinated to Fe2+ on the metal surface. Furthermore, the peak
at 1456 cm-1 was due to ZnO2 [20]. This may be explained by the fact that Zn(OH)2 formed
on the cathodic sites [19] converts into ZnO2.
Analysis of the UV-Visible Reflectance Spectra
The UV-visible reflectance spectra of the films formed on the surface of metal specimens
immersed in various test solutions are given in Fig. 3. The spectrum of the film due to the
environment containing 60 ppm Cl- and 300 ppm MoO42- shows a peak at 320 nm (Fig. 3a).
This may be due to a complex formed between the iron and molybdate.
The spectrum of the film formed on the surface of the metal immersed in the
environment, consisting of 60 ppm Cl-, 300 ppm MoO42- and 50 ppm Zn2+ is given in Fig. 3b.
The wavelength transition at 550 nm indicates the presence of oxides of iron (band gap =
1.239/0.55 = 2.25 eV) on the metal surface [21] having semiconducting property [22]. The
peak at 320 nm may be due to an iron-molybdate complex.
(h) Cl- 60 ppm + EPA 300 ppm + MoO42300 ppm + Zn2+ 50 ppm
486
Rajendran et al.
The spectrum of the film due to the environment consisting of 60 ppm Cl-, 300 ppm
MoO42- and 300 ppm EPA (Fig. 3c) does not show any wavelength transition at 550 nm
indicating the absence of any oxides of iron on the metal surface. The peak at 320 nm is due
to an iron-molybdate complex formed on the metal surface.
The reflectance spectrum of the film due to the environment containing 60 ppm Cl-, 300
ppm MoO42-,300 ppm EPA and 50 ppm Zn2+ (Fig. 3d) has a peak at 320 nm due to an ironmolybdate complex. Absence of a wavelength transition at 550 nm indicates the absence of
oxides of iron on the metal surface.
Analysis of the X-Ray Diffraction Patterns
The XRD patterns of the film formed on the surface of the metal specimens immersed in
various test solutions are given in Fig. 4. The XRD pattern of the film due to the environment
consisting of 60 ppm Cl- and 300 ppm MoO42- is given in Fig. 4a. The film consisted of
Fe2(MoO4)3 (2 = 14.1, 22.6, 30.63 and 31.88) [23]. The peaks due to iron appear at 2 =
44.5, 64.8 and 82.2.
The film formed on the surface of the metal specimen immersed in the environment
containing 60 ppm Cl-, 300 ppm MoO42- and 50 ppm Zn2+ contained Fe2(MoO4)3 (2 = 22.0,
26.7, 45.5, 66.1) [23], ZnO2 (2 = 45.5 and 66.1) [24] and -FeOOH (2 = 60.9) [25].
The iron peaks appear at 2 = 44.6, 65.0 and 82.3.
487
488
Rajendran et al.
3. On the surface of the metal, the Zn2+-EPA complex is converted into an Fe2+-EPA
complex in the local anodic sites, since the latter is more stable than the former.
Zn2+-EPA + Fe2+ ---> Fe2+ -EPA + Zn2+
(1)
(2)
(3)
490
ABSTRACT
Four organic based corrosion inhibitors have been evaluated for carbon steel, Monel 400 (UNS
No 400) and stainless steel 321 (UNS No. 32100) in fresh monoethanolamine (MEA) environments
saturated with an H2/CO2 gas mixture at 40oC. The test solutions were prepared from fresh MEA
solutions with and without the addition of 250 ppm of each inhibitor. Initial screening of the
inhibitors was performed using the wheel test to determine the corrosion rates of the three alloys with
and without inhibitors. The rotating disc electrode (RDE) method was used to determine the
effectiveness of the four organic inhibitors under hydrodynamic conditions. It was found that flow
conditions tended to increase the effectiveness of some corrosion inhibitors with respect to stagnant
conditions. The weight-loss and electrochemical tests conducted under hydrodynamic conditions
indicated that the quaternary ammonium-based inhibitor was the most effective of the three alloys in
the different MEA solutions.
Key Words: Corrosion inhibitors, carbon steel, monel 400, stainless steel 321, monoethanolamine,
weight-loss, rotating disc electrode
INTRODUCTION
A large variety of corrosive conditions is encountered in the different industries. The
costs of corrosion, and correspondingly, the savings gained through the use of appropriate
corrosion mitigation techniques is considerable. Corrosion inhibitors are one of the main
methods used to reduce corrosion problems in metallic installations all over the world.
One of the most expensive and corrodible installations in chemical plants and refineries
is the gas purification system. The most economical and effective method of protection is the
addition of inhibitors to the closed circulation circuit of the system. Because carbon steel,
UNS No 400 and stainless steel 321 (SS321) are the major alloys of construction in
monoethanolamine (MEA) gas treating systems, both inorganic- and organic-based inhibitors
have been utilized to reduce the corrosion rate in such an environment. However, due to
environmental regulations and toxicity considerations, the use of inorganic inhibitors is
declining and that of organic-based inhibitors is rising. The ability to evaluate and screen
corrosion inhibitors for this type of application is important in order to choose an appropriate
inhibitor.
493
It is well known that flow velocity exerts a great influence on the corrosion rate of
metallic materials [1,2]. Despite this knowledge the importance of the flow rate is not
sufficiently considered in evaluation tests of corrosion inhibitors. The use of circulating
loops to enable the examination of a wide range of flow rates (laminar and turbulent) is
sometimes considered too expensive and time consuming because of the long sequence of
operations needed [3]. Several authors [2,4,5] suggest simulating the turbulent flow present
in many systems by using rotating disc electrodes (RDEs). In this technique, cylindrical
electrodes are rotated at different speeds to measure the effect of flow at various velocities.
This work was undertaken to screen four corrosion inhibitors in fresh monoethanolamine
saturated with 85% CO2/15% H2 using the weight-loss and RDE methods. The aim of this
investigation was to determine which corrosion inhibitor produces the lowest corrosion rate
for carbon steel, UNS No 400 and SS321 in MEA solution by correlating the data obtained by
the weight-loss and RDE methods.
EXPERIMENTAL PROCEDURE
Materials
The materials tested were carbon steel (ASTM A283 grade B) Monel 400 and SS321.
All the alloys were supplied by the Kuwait National Petroleum Company (KNPC) and
represent the materials of construction of the plant.
Inhibitors Tested
Four corrosion inhibitors were tested under stagnant conditions by the weight-loss test,
and under flow conditions by the RDE technique. The inhibitors were labeled A, B, C and D
for simplicity and are shown in Table 1.
Table 1. Type of Commercial Inhibitors Tested
Inhibitor Type
A
B
C
D
Chemical Family
Amides
Aklylamino acid and ethylene glycol
Amines
Quaternary ammonium compound
Weight-Loss Method
The procedure for the weight-loss method is essentially like that given in ASTM
standard G-31 (1990). The specimens were in the form of coupons in dimensions of 40 x 20
x 1 mm. Before exposure to the test environment, the surfaces of the coupons were
successively ground with 180, 400 and 600 grit silicon carbide papers, washed with detergent
and dried. The weight of each specimen was determined accurately on an electronic balance.
Prior to immersion in the test medium, the coupons were decreased in acetone and dried by
hot air and hung with nylon thread. The test vessels were 800 ml Pyrex glass fitted with a gas
inlet and immersed in thermostatically controlled water baths. The volume of the test
solution was 400 ml. Each cell contained 2 coupons of carbon steel. During the course of the
494
Carew et al.
test, coupons were removed after 2 and 4 weeks. After weight-loss determination, the
corrosion rate was calculated from the weight loss data as (mpy) from the following formula
according to ASTM G-31 (1990).
Corrosion rate = (K x W)/(A x T x D)
(1)
where
K = constant = 3.45 X 106, W = mass loss in g, A = area in cm2, T = time of exposure
in hours, and D = density in g/cm3.
Rotating Disc Electrode (RDE)
For the RDE measurements, the system Model 616 RDE, by EG&G PARC, was used,
mounting and rotating the cylindrical electrodes at 200, 1000, and 3000 rpm. Some tests
were conducted under stagnant conditions for comparison. The corrosion rates for the steel
electrodes were determined at each speed selected, by using a potentiostat/galvanostat
M000odel 273 A by EG&G PARC through the linear polarization resistance (LPR)
measurement method.
The electrochemical cell used consisted of the working electrode, a graphite counter and
a saturated calomel electrode (SCE) as a reference electrode. The test was conducted with 400
ml of fresh MEA solution. Tests were conducted in 4 uninhibited MEA solutions as well as
solutions inhibited ones with addition of 250 ppm of each inhibitor. The solution was
continuously purged with a gas mixture of 85% CO2 and 15% H2 ,and the temperature was
maintained at 40C.
RESULTS
Weight-Loss Method
Carbon Steel. Figure 1 shows the corrosion rate of this alloy in fresh (18% H2O) MEA
solution in the presence of four organic-based inhibitors at a temperature of 40C for a period
of 4 weeks. To determine the most effective inhibitor in the MEA solution for this alloy, it
was decided to rank the inhibitors by comparing the corrosion rates of the alloy in the
absence and presence of inhibitors. In other words, the corrosion inhibitor that reduced the
corrosion rate of carbon steel to the lowest value would be ranked as the best, and the one
with the highest corrosion rate would be ranked as the worst. The corrosion rate of carbon
steel in fresh MEA and in the absence of any corrosion inhibitor was considered to be the
reference point (blank conditions). Therefore, the ranking of the inhibitors in terms of their
corrosion performance for carbon steel in fresh MEA solution was as follows (Fig. 1):
D>C>A>B
Monel 400. Figure 2 illustrates the corrosion rates of this alloy in fresh MEA solution in
the absence and pressure of the four inhibitors at 40C and after four weeks of immersion.
The ranking of these inhibitors in terms of their corrosion protection to Monel 400 in the
fresh MEA-solutions is as follows:
A>D>B>C
495
496
Carew et al.
497
498
Carew et al.
Figure 3 shows the corrosion rate of SS321 under stagnant conditions which was quite
low in the uninhibited media. The addition of inhibitors C and D reduced the corrosion rate
of SS321 to very low levels. However, the addition of inhibitors A and B increased the
corrosion rate of this alloy. This behavior was observed for SS304 and SS316 in identical
media in previous studies [6,7].
Under hydrodynamic conditions, the corrosion rate of carbon steel, as shown in Fig. 4,
indicates that under blank conditions, the flow velocity tended to decrease the corrosion rate
of this alloy, in comparison to stagnant condition. This observation has been reported by
many authors [1,2,4,5]. However, the dissolution rate of the steel cylinders in the inhibited
MEA solutions were some what independent of the rotation velocity. This behavior may be
interpreted by assuming the formation of a thick surface layer on the carbon steel electode.
This layer strongly hindered either the anodic or the cathodic reaction or both on the surface
of the steel electrode. Such a phenomenon was also reported by Zucchi et al.[2].
The corrosion rate of Monel 400 under flow conditions (Fig. 5) was lower under
uninhibited conditions for the three different velocities than for samples with inhibitors A, B,
C, and D. According to Fig. 5, Monel 400 did not seem to be affected by the different
rotational speeds in the uninhibited MEA solutions. In other words, the passive oxide layer
on the surface of Monel 400 was sufficient to resist destruction at up to 3000 rpm. The
increase in the corrosion rate of this alloy upon the addition of the 4 inhibitors could be
attributed to the removal or nonuniform formation of inhibitor film under hydrodynamic
conditions.
Figure 6 shows the corrosion rate of SS321 under hydrodynamic conditions in the
uninhibited and inhibited MEA solutions. The addition of inhibitors A, B and C tended to
lower the corrosion rate of SS321 under flow conditions. Inhibitor C seemed to be the most
effective one in reducing the corrosion rate of SS321.
Based on the results obtained by the weight-loss and RDE methods, the inhibitor that
seemed to be the most effective in reducing the overall general corrosion rate for the three
alloys was inhibitor D (quaternary ammonium compound). Generally, the inhibition
mechanism of this compound is due to its ability to adsorb into the metal or alloy surface to
form a protective film. Organic inhibitors can adsorb on to a metal surface by hydrogen
bonding, by electron donation from the nitrogen atom, or by interaction of the dipole with the
surface charge [8, 9, 10].
CONCLUSIONS
The most effective corrosion inhibitor that may be used for carbon steel, Monel 400 and
SS321 as determined under laboratory conditions, is the quaternary ammonium compound.
The corrosion rate of the three alloys in the inhibited fresh MEA solutions varied with respect
to flow conditions. The corrosion rate of carbon steel under such conditions was independent
of the rotational speed, slightly increased for Monel 400 and decreased with respect to SS321.
ACKNOWLEDGMENT
The authors would like to acknowledge the in-kind support of KNPCs - Shuaiba
Refinery of this research work.
499
REFERENCES
1. E. Heitz, Corrosion 90, Paper No. 1, NACE, Houston, Texas, USA., 1990.
2. F. Zucchi, G. Trabanelli, and G. Brunoro, Effect of flow velocity on corrosion inhibition
of steel in HCl, in Progress in the Understanding and Prevention of Corrosion, Vol.2, J.
M. Costa and A. D. Mercer, eds.,The Institute of Materials, p. 845, 1993.
3. J.L. Dawson, C.C. Shih, R.G. Miller and J.W. Palmer, Corrosion 90, Paper No. 14,
NACE, Houston, Texas, USA., 1990.
4. A. Mazanek and H. Bala, Corrosion Science 28, 5, 1988, p. 513.
5. D.C. Silverman, Corrosion prediction from circuit models application to evaluation of
corrosion inhibitors, in electrochemical impedance - Analysis and Interpretation, J.
Scully, D. Silverman, and M. Kendig Editors, ASTM Publication, Philadelphia,
Pensylvania,1993, p. 192.
6. M. Islam, A. Abdullah, W. Riad and G. Mansi, An investigation of corrosion and its
control in the PIC monoethanolamine carbon dioxide removal unit. Kuwait Institute for
Scientific Research, Report No. KISR 1446, Kuwait 1984.
7. M. Islam, A. Abdullah, W. Riad , R. Al-Taib and G. Mansi, An investigation of corrosion
and its control in the PIC MEA carbon dioxide removal unit laboratory studies, Kuwait
Institute for Scientific Research, Report No. KISR 1603, Kuwait 1984.
8. A. Moccari and D. D. Macdonald, Corrosion 41, 5, 1985, p. 263,
9. J.S. Robinson, Corrosion Inhibitors, 1979.
10. C.C. Nathan, Corrosion Inhibitors, NACE publications, Houston Texas, USA, 1973.
500
ABSTRACT
Cyclic polarization experiments were performed on 1018 steel, yellow brass, and 6061-T6 aluminum
in ozonated and non-ozonated tap water under stagnant conditions to evaluate pitting and corrosion
tendencies of these engineering metals. Results show that the corrosion rate of 1018 carbon steel in tap
water under stagnant conditions increased about three-fold with the injection of ozone (0.05-0.1 ppm). No
considerable changes in the corrosion rate occurred for yellow brass and aluminum when ozone was added
under similar conditions. Study of the pitting behavior of the materials also demonstrated that ozone did
not increase pitting when injected into the test solution for yellow brass. But in the case of 1018 carbon
steel and aluminum, pitting was more pronounced.
Key Words:
INTRODUCTION
It is now a well known fact that the injection of ozone into the cooling water circulated in
cooling towers can help to prevent biofouling due to the biocidal property of ozone [1-4]. Ozone
is a strong oxidizer that is unstable at standard temperature and pressure [5]. Recently ozone has
attracted a great deal of interest for its application as a corrosion inhibitor for open recirculating
cooling towers. Some of the advantages of ozone versus multichemical water treatment systems
currently in use include: (1) minimal on-site chemical inventory, (2) no toxic discharge, (3) water
conservation, and (4) cost effectiveness. However, there are potential disadvantages for ozone
applications that include: (1) possible corrosiveness to metallic components and (2)
incompatibility with common inhibitors. Literature data indicate conflicting results on the effect
of ozone on the corrosion of metals. Pryor and Buckay [6] summarized some case histories of
both success and failure of ozone application in cooling towers of different industries.
Matsudaira et al. [7] reported about two to three-fold increases in the corrosion rate with
increasing ozone concentrations for carbon steel under stagnant and slow flow states in deionized
water, and five to six-fold increases for brass under similar conditions. Walton [8] performed
similar experiments as Matsudaira et al. [7] and reported a decrease in corrosion rates for mild
steel and aluminum with increasing ozone concentrations. Obviously there are contradictions in
these two cases as well as in a number of other investigations. Furthermore, to the best of our
knowledge no research has been done to investigate the pitting tendencies of cooling tower
materials when exposed to ozonated aqueous solutions. The objectives of this study were to
501
evaluate the effect of ozone on the corrosion rates and pitting tendencies of 1018 carbon steel,
yellow brass, and aluminum.
EXPERIMENTAL PROCEDURE
The cyclic polarization technique was used to study the pitting behavior and corrosion rates
of 1018 carbon steel, yellow brass, and aluminum 6061-T6. This technique enables both pitting
tendency evaluation as well as corrosion rate measurement of a metallic specimen in a given
metal-solution system. The setup consists of a test cell, a potentiostat (VersastatTM), and an
ozone generator using an ultraviolet lamp. The test cell contained the test solution (tap water),
and the test specimen which was prepared according to procedures outlined in ASTM G5-87 [9].
Dry air was passed through the ozone generator and into the cell at a constant flow rate. The
specimen was soaked in the solution for one hour before the cyclic polarization scan to attain a
steady-state condition. The specimen was then polarized from -0.25 V with respect to the opencircuit potential (oc) to 0.7 V, and then reverse scan to -0.05 V (oc). All potentials referred to in
this paper are with respect to saturated calomel electrode (SCE). The pH of the solution before
and after the scan was measured. Also, the ozone concentration in the solution before and after
the polarization scan was determined by either the indigo trisulfonate method or the DPD method
(supplied by the Hach Company) whenever applicable. The corrosion rates of the materials were
then determined by the EG&G Corrosion Measurement and Analysis software (MODEL 352
SoftCorrTM II) which uses a nonlinear least-squares fit algorithm to fit the data to the Stern-Geary
equation [10] to obtain parameters for the calculation of corrosion rates. A metallograph
(Versamet UNITRON 5327) was employed to document the surface conditions of the test
samples before and after each test.
RESULTS AND DISCUSSION
The concentrations of ozone were maintained within the range of 0.05-0.1 ppm for all
experiments involving ozonation. The pH of the test solutions were found to remain relatively
unchanged in the region of 7.3 throughout the course of the scan for either case with or without
ozone.
1018 Carbon Steel
A comparison of the corrosion rates of 1018 carbon steel in ozonated and non-ozonated tap
water (Table 1) indicates an increase of about three times in the corrosion rates from about 16.5
mpy to about 56.5 mpy with the injection of about 0.1 ppm of ozone. These numbers agree with
the findings of Matsudaira et al. [7] who reported about two to three-fold increases in the
corrosion rate with increasing ozone concentrations for carbon steel under stagnant and slow flow
states in deionized water. The open-circuit potential of steels exposed to ozonated water shifted
toward the cathodic direction by about 0.1 V. Such a slight shift in cathodic direction for a
lightly ozonated system agrees with the results of Strittmatter et al. [11].
The general shape of the cyclic polarization plots (Fig. 1) in the absence of ozone indicates
the presence of knees at pitting potential (Epit) where the corrosion current increases drastically.
Such Epit was not seen for the steel sample tested in ozonated water. In addition, extrapolation of
the reverse scan shows that the protection potential (Epro) is lower than the pitting potential (Epit)
meaning that the tendency for pits to form is great. Indeed, photographs of the 1018 carbon steel
specimens surfaces tested in ozonated and non-ozonated solutions before and after the scan (Fig.
2a-d) show that extensive pitting had occurred on the steel samples tested in ozonated solutions.
502
Nasrazadani
Figure 1 also indicates that pitting occurred on steel at a much lower potential with the
introduction of ozone. This can be explained by the gentler anodic slopes of the plots, and the
absence of the kneel as observed in Fig. 1 for steel samples tested in ozonated solutions.
However, inspection of the photographs taken on those specimens with ozonation (Fig. 2d)
shows no differences in the extent of pitting compared to those without ozonation (Fig. 2b). One
can conclude that ozone does not increase the extent of pitting in carbon steel, but instead,
accelerates the formation of pits.
Table 1. Corrosion Rates of 1018 Carbon Steel
Experiment
Number
Dry Air
Only
1
2
3
4
Ozonated
Dry Air
Corrosion Rates
(mpy)
9.57
8.39
22.80
25.47
-------Avg. 16.50
33.94
2
3
4
Open-Circuit
Potential
(V vs. SCE)
-0.3530
-0.4640
-0.3970
-0.4140
-0.5080
59.77
64.11
68.26
-------Avg. 56.50
-0.5520
-0.5320
-0.5090
503
Figure 1. Cyclic polarization plots of 1018 carbon steel exposed to ozonated (0.1 ppm) and nonozonated solutions
504
Nasrazadani
Figure 2. Micrographs of 1018 carbon steel surfaces exposed to non-ozonated (a and b) and
ozonated (c and d) solutions before (a and c) and after (b and d) cyclic polarization
experiments (magnification 50x)
Yellow Brass
Corrosion rates for yellow brass remain relatively unchanged in the low range between one
and four mpy (Table 2) for both cases in ozonated and non-ozonated conditions. The overlay of
both ozonated and non-ozonated cyclic polarization plots (Fig. 3) shows no significant shift in the
corrosion potential (Ecorr). These results contradict the findings of Matsudaira et al. [7] who
reported five to six-fold increases for the corrosion rates of brass. In either ozonated and nonozonated conditions, the general shape of the plots is almost identical implying that ozone does
not change the extent of pitting for yellow brass. The small area of the hysteresis loop also
indicates that pitting is not as serious a problem as in carbon steel. Photographs of yellow brass
test specimens (Fig. 4a-d) confirm this conclusion. Figure 4 shows no real differences in the
number of pits for cases with and without ozonation.
Table 2. Corrosion Rates of Yellow Brass
Experiment
Number
Dry Air
Only
Corrosion Rate
(mpy)
1
2
Avg.
Ozonated
Dry Air
3.02
3.86
-----3.44
1.12
-0.0023
3.42
Avg.
Open-Circuit
Potential
(V vs. SCE)
-0.0018
-0.0048
-0.0017
-----2.27
505
Figure 3. Cyclic polarization plots of yellow brass exposed to ozonated (0.1 ppm) and nonozonated solutions
506
Nasrazadani
Figure 4. Micrographs of yellow brass surface exposed to non-ozonated (a and b) and ozonated
(c and d) solutions before (a and c) and after (b and d) cyclic polarization experiments
(magnification 50x)
Aluminum 6061
As in the case of yellow brass, the corrosion rates for aluminum remain relatively low and
without much variation between 0.78 mpy to 1.12 mpy for both ozonated and non-ozonated
conditions (Table 3). The overlay of the plots (Fig. 5) also shows no significant differences in the
general shape or shift in the Ecorr under either condition. However, the area of the hysteresis loop
is larger in the case of the ozonated scan which indicates that pitting has increased. Indeed, a
comparison of the micrographs taken before and after the scan (Fig. 6 a-d) shows that pitting is
more extensive under ozonated conditions.
Table 3. Corrosion Rates of 6061 Aluminum
Experiment
Number
Dry Air
Only
Corrosion Rate
(mpy)
1
2
Avg.
Ozonated
Dry Air
1.07
0.79
-----0.93
0.45
Open-Circuit
Potential
(V vs. SCE)
-0.4570
-0.4560
-0.0023
1.12
Avg.
1.12
-----0.90
-0.4450
-0.4900
507
Figure 5. Cyclic polarization plots of aluminum 6061-T6 exposed to ozonated (0.1 ppm) and
non-ozonated solutions
508
Nasrazadani
509
ABSTRACT
For over thirty years, corrosion coupons (weight-loss coupons) have been used in industrial
processes to measure corrosion rates. These simple and reliable devices provide an accurate measure
of corrosion rate in any environment, but require an extended time base before meaningful (and
therefore historical) information can be obtained. Electrical resistance (E/R) probes provide the means
to electrically transmit and record corrosion rate data based on the correlation of the increase in the
electrical resistance of the probe element to the metal loss of the element. Although useable in any
process environment, this technique also requires an extended time base before data is available.
The linear polarization resistance (LPR) technique provides instantaneous corrosion rate data.
However, it is applicable only in conductive media. Newer techniques provide the combined benefit
of the rapid response of LPR probes to the universal applicability of E/R probes and coupons.
In this paper, the limitations of all current corrosion monitoring techniques will be critically
evaluated. For each technique, application limitations will be described in terms of corrosive media
characteristics (i.e., temperature, pressure, conductivity, H2S concentration, pH, and phase) as well as
probe characteristics (i.e., response time, sensitivity, alloy availability, and means of insertion). The
result is a definitive guide to the selection of the proper corrosion monitoring technique for any
industrial application.
Key Words: Corrosion monitoring, new, rapid techniques, MICROCORTM, LPR, electric resistance
SYNOPSIS
The electrical resistance (E/R) and linear polarization resistance (LPR) methods for online corrosion monitoring are compared with a new technique based on measurement of
inductive resistance. Particular emphasis is given to the breadth of applicability of
techniques, and the speed with which they measure changes in corrosion rate. Comparative
test data show the new technique to have both the rapid response of LPR plus the universal
applicability of E/R.
INTRODUCTION
Electrical resistance (E/R) and linear polarization resistance (LPR) are the industry's
standard technique for on-line, instrumented, corrosion monitoring. The former is universally
applicable, but response time is measured at best in days or weeks [1,2]. The latter gives
511
rapid response, but is restricted to continuous electrolyte corrodents, and provides only semiquantitative data [1].
Newer techniques [2] such as thin-layer activation, ultrasonic transducers, the "field
signature-method", electrochemical noise, and AC-impedance are more costly, some
prohibitively so. They are also extremely slow to respond, or give complex and ambiguous
data requiring expert analysis and interpretation. All have specialized applications, and none
show promise as a general monitoring technique that overcomes the limitations of the more
traditional methods.
Inductive resistance measurements do, however, offer the response speed of LPR
coupled with the universal applicability and absolute measurement capability of E/R. This
paper reviews the performance characteristics of all three techniques.
Electrical Resistance Measurements
E/R, the most widely used of instrumented corrosion monitoring methods, measures the
increase in electrical resistance of a metal sensor as its cross-section is reduced by corrosion.
It will operate in almost any environment, and it provides an absolute measure of metal loss
[3].
Only sulfide environments present difficulties for the E/R technique; electrically
conducting iron sulfide corrosion products cause underestimates of metal loss. In extreme
cases, sensors will indicate a metal gain [4] which, being obviously erroneous, is less serious
than moderate instances showing corrosion rates that are lower than the actual values. This
seriously limits the utility of the technique in sour oil and gas production systems, and
refineries processing sour crude. Figure 1 shows comparative weight-loss and electrical
resistance data in sour service.
A second, and more fundamental drawback is the lengthy response time of this
technique. Sensors that are sufficiently long-lived and rugged enough to be used in industrial
environments have very low electrical resistance, as illustrated in Table 1. Removal of
sufficient metal for a measurable resistance increase to occur can take days, or even weeks
[2,3]. Response time is a function of sensor thickness, absolute resistance, and corrosion rate.
Typical manufacturers' data relating response time and probe-life to corrosion-rate and
element thickness are shown in Fig. 2. Evidently the most sensitive senors will take almost
five days to register a corrosion rate change of 1 MPY. Perhaps this is more clearly
illustrated in Fig. 3a and 3b, which show data from electrical resistance sensors of varying
thicknesses in stagnant, potable, water showing a corrosion rate of about 5 MPY for carbon
steel. Figure 3a also illustrates the increasing scatter experienced as the sensor resistance
decreases, this is dramatically illustrated when comparing data from the 40 mil wire-loop and
20 mil cylindrical sensors.
Table 1. E/R Element Resistance
(a)
(b)
Figure 3. E/R data scatter
Compensation for temperature effects in E/R sensors is accomplished by measuring the
resistance ratio of the corroding sensor to a second, noncorroding sensor housed within the
probes body. The exposed and protected sensors are equally influenced by temperature, and
514
consequently, ratio changes result exclusively from metal loss at the exposed sensor. Figure
4 illustrates the effect of small, rapid, temperature perturbations on sensor readings.
Although the resulting changes in probe readings are significant, they recover in less than two
minutes, and adequate temperature compensation is demonstrated.
(1)
C1 is a constant comprising a function of the Tafel rate constant (a, Bc), and C2 is a
constant involving dimensional factors, equivalent weight, density, time conversions, and the
Faradays constant.
515
517
518
environment. These combined attributes cannot be found in any of the other techniques
currently employed for on-line corrosion monitoring.
REFERENCES
2.
3.
4.
5.
6.
7.
8.
1. S.W. Dean, ASTM STP908, Corrosion Monitoring in Industrial Plants, 1986, pp. 197218.
M.W. Joosten, K.P. Fisher, R. Strommen and K.C. Lunden, Materials Performance, April
1995, pp. 44-48.
G.L. Cooper, ASTM STP908, Corrosion Monitoring in Industrial Plants, 1986, pp. 237250.
G.R. Cameron and L.G. Coker, ASTM STP908, Corrosion Monitoring in Industrial Plant,
1986, pp. 251-265.
M. Stern and A.J. Geary, Journal of the Electrochemical Society 104, 1957, p. 56.
K.M. Lawson, N.G. Thompson, and M. Islam, NACE International Corrosion
Conference, Paper No. 310, 1994.
R.A. Yeske, ASTM STP908, Corrosion Monitoring in Industrial Plants, 1986, pp. 266288.
K.M. Lawson, N.G. Thompson, M. Islam and M.J. Schofield, British Journal of NonDestructive Testing, 35, 6, June 1993, pp. 319-329.
519
ABSTRACT
Acoustic emission (AE) is a nondestructive technique originally developed to locate possible
defects on nuclear vessels during hydrotesting. The development of a different signal analysis and of
an interpretation code based on characteristics of environmental crack growth allows the use of such a
simple technique to inspect plants during service, and to detect and locate active defects. A number of
industrial applications for detection of stress corrosion cracks, of embrittled zones and of corrosion
fatigue cracks will be presented. AE can be further used to evidence of the effectiveness of
electrochemical treatments aimed at stopping stress corrosion cracking (SCC).
Key Words: Acoustic emssion, nondestructive techniques, plant inspection, active defects, stress
corrosion cracks, fatigue cracks
INTRODUCTION
Among localized corrosion forms, those caused by interplay between a specific corrosion
medium and mechanical stresses (either applied or residual) can provoke potentially
dangerous cracks. In most cases, such cracks are generated on the internal wall of a vessel, a
pipe or another plant component and cannot be detected unless an outside leak is produced or
a complete internal inspection is carried out during a plant shutdown. Acoustic emission
(AE) is the only nondestructive technique that can reveal the presence of active cracks, i.e.,
those defects growing under service conditions, and therefore, is especially suited to detect,
locate and monitor the occurrence and propagation of stress corrosion, hydrogen
embrittlement and corrosion fatigue, the so-called environmental cracking.
The Technique and the Theory
AE was initially developed to locate metal defects on relatively large structures
(typically nuclear vessels) during the final hydrotesting. The theory of fracture mechanics
assumes that a defect, when subjected to a suitable load, can progress in a discontinuous
mode, and therefore, it would be possible to detect its presence during the increase of an
applied load such as pressure. Because of this theoretical approach, AE has been mostly used
in hydraulic tests, and localization techniques based on a large number of sensors have been
developed. Also when applied to a plant component after a certain period of service, e.g., as
in the requalification of pressure vessels, the AE test has been consistently associated with an
increase of pressure. To detect an AE signal from a far away source requires a very high gain
521
of the amplification chain; a fact that severely limits the use of AE in a noisy environment.
Unfortunately, the results obtained with AE as a defect localization system have been very
poor for a number of reasons, among which the use of the fracture mechanics concepts might
be considered major. A much more successful application of AE can be obtained when the
electrochemical approach to environmental fracture is adopted.
The basic concept of electrochemical theory is the existence of surface conditions
(quantified and described by the electrochemical potential) which can nucleate and propagate
brittle cracks, while the mechanical factor (external and/or local stresses) only determines the
rate of crack propagation. Crack propagation itself depends on a number of phenomena (e.g.,
local corrosion, acidification, formation and rupture of protective oxides or films, hydrogen
diffusion, and dislocation movement), most of which are totally or largely insensitive to the
extremely small variation in local stress induced by a pressure increase. Accordingly, AE
must be applied only when such critical conditions exist and for a length of time consistent
with the specific type of brittle cracking. For all practical purposes, the electrochemical
theory suggests the use of AE during the normal service of a given plant component to detect
whether active cracks are present. This requires, in turn, the capability of distinguishing a
signal generated by a brittle crack extension from all possible signals generated by
concomitant, but not interesting, phenomena (noise).
Acoustic Emission Energy
The parameter that permits distinguishing between crack activity and noise is the energy
transported by the signal. An AE signal is a damped oscillating wave, and its energy is
proportional to the square of the maximal amplitude. For each signal, it is necessary to
measure the maximal amplitude, to calculate the squared value and to add all contributions in
order to generate an energy output. Other types of energy calculations (e.g., the envelope of
the signal and the integral) are not suitable; therefore, the calculation of the maximal
amplitude squared has been called true energy analysis (TEA). The main reason for
favouring this parameter is the large difference in value between the energy released by a
crack the moment it grows compared with the energies associated with noise signals. In order
to measure the maximal amplitudes of AE signals, it is very important to avoid signal
deformation caused by excessive gain in the amplification chain; in other words, the range of
amplitudes to be measured should be known.
The TEA Code and Environmental Cracking
Interpretation of AE data to detect and locate environmental cracks is possible on the
basis of a set of criteria which form the TEA Code. Obviously such criteria are related to the
specific cracking phenomenon and take into account how crack propagation mechanisms are
expected to generate AE signals. A brief discussion of environmental cracking phenomena
can help in identifying basic evaluation criteria for AE signals.
In the case of stress corrosion cracking (SCC), the crack nucleation and growth
processes can be simplified as follows:
Giuliani
Hydrogen atoms are produced at the metal surface either by electrolytic reduction
of hydrogen ions or water molecules, or by reaction with hydrogenated
compounds;
Hydrogen atoms enter the metallic matrix (especially in the presence of promoters
such as H2S, CN-, As and Sb compounds) and diffuse to regions of high local
stresses such as those around hard inclusions (e.g., aluminates and
aluminosilicates).
A brittle area is created around the inclusion, and this results in metal detachment;
The stress relaxation following the formation of the crack promotes a diffusion of
hydrogen away from the cracked area to adjacent inclusions.
On the basis of such a simplified mechanism, relatively few, but highy energetic, signals
are generated at the moment the embrittled metal is cracked; cracks can be more localized
because they depend on the metallurgical defects of the steel, and they will occur at longer
time intervals when compared to SCC cracks. More isolated energy jumps are expected.
Again, there is no relation between crack signal frequency and any other variation in the
plants operating conditions.
The corrosion fatigue cracking rate is directly related to the stress variation frequency,
and therefore, for practical purposes, AE signals are much more frequent and increase in
number with the length of the crack. Energy jumps are more regularly spaced but different in
magnitude because the amount of fractured surface in the elemental crack growth step is
different. In the case of a noisy environment, corrosion fatigue cracks can be evidenced by
peaks in the plot of energy/oscillation against time.
For all three phenomena, there are locations where cracking is more likely to occur:
welds, junctions, geometrical discontinuities and the like. It is, in general, always possible to
compare AE signals obtained near one of these preferential locations with signals obtained
523
from locations where the probability of cracking is very low. Further, it is possible to utilize
signal attenuation to locate zones or regions of the structure where cracks are active. Finally,
based on the described interpretation method, continuous monitoring becomes feasible as a
few transducers independently listen to detect possible nucleation of brittle cracks.
AE Confirmation
A major problem of conducting an AE test during hydrotesting is the well known Kaiser
effect: if a defect emits at a given pressure, it will remain silent when the test is repeated
unless the previous pressure is exceeded. This effect hinders the repetition of the AE test
(apart from practical and economical difficulties) in order to verify the presence of a defect.
The application of AE to in-service inspection completely overcomes this problem because
defect propagation is a continuously repeated process. It is possible, therefore, to confirm the
existence of active defects in any given location by repeating the AE inspection at any time.
RESULTS
Some typical results of AE inspection are presented in order to evidence the usefulness
of the energy calculation.
Corrosion Fatigue
A carter of a large CO2 compressor for a urea plant was inspected to detect corrosion
fatigue cracks during operation. One transducer was positioned near a carter weld for less
than 20 minutes and then moved to another weld. The amount of noise associated with the
compressor is enormous, and in every position on the carter, the number of oscillations is
nearly constant and in excess of 50,000/minute. The calculation of energy, however, shows a
completely different picture. Figure 1a refers to a position where no crack was present and
shows how the energy content of the AE signals is constant and very low. Figures 1b and 1c
report results obtained on a weld where a crack had been previously revealed by penetrant
dye and on a weld that had passed the penetrant dye test, respectively. In both cases, the
amount of emitted energy was much higher and discontinuous in time, while no difference at
all can be noticed in the amount of oscillations when compared to Fig. 1a. Another crack was
detected on the second weld after grinding and repetition of the penetrant dye test. Figure 2
gives the amount of emitted energy per minute in the three locations, plotted in a
semilogarithmic scale: it is easy to see that cracks emit energies which are orders of
magnitudes higher than noise.
Hydrogen Cracking
A high-temperature reactor containing hydrogen was inspected to detect whether there
was an active process of cracking under the prevailing operating conditions. By positioning
one transducer at several locations on the vessel, one zone near a manhole was found emitting
highly energetic signals. Figure 3 gives a typical result obtained from the defective zone; it
should be compared to the zero emission at the other locations on the vessel. It is evident that
524
Giuliani
(a)
(b)
(c)
Figure 1. Results from a carter of a CO2 compressor of a urea plant at (a) a position where no
crack was present; (b) a weld where a crack had been previously revealed by
penetrant dye; and (c) a weld that had passed the penetrant dye test
525
Giuliani
Figure 4. Results obtained on a Horton sphere containing LNG (the three plots refer to
reptitions of the test on the weld)
528
Giuliani
Figure 5. A plot of the total emitted energy against time during nucleation and initial
propagation of cracks in a stainless steel pipe through which hot CaCl2 was
flowing
Figure 6. A plot of the energy derivative E/t as a function of time during the period of
SCC crack propagation in Monel pipes
529
Giuliani
gas holder of carbon steel [1]. AE signals can be used as evidence in real time of the
effectiveness of a treatment aimed at potential modification: when cracks stop propagating,
AE signals decrease to zero (Figs. 7 and 8).
CONCLUSIONS
AE is an invaluable, nondestructive technique when used to detect active cracks in
industrial plants under service conditions because there is no alternative technique able to
provide the same real time information. In many industrial plants, under normal service
conditions, unless unexpected substantial overload occurs, the only active cracks are those
that grow because of a specific environment, e.g., those generated by SCC, hydrogen
embrittlement or corrosion fatigue. Such cracks do not progress because of any pressure
increase as the external load is only one of the factors determining their growth, and in many
cases, not the most important one, when internal stresses are considered.
The use of AE for in-service inspection is based on proper analysis of signals and on
proper correlation with the emitting phenomenon: the TEA Code is an example of such an
analysis. The possibility of using AE while a plant is in service is the basis for its economical
use. Indeed, AE should be used to locate those areas where active cracks are present and
should be subjected to inspection during plant shutdown. Such a pre-check substantially
reduces the need for extensive inspection with magnetic particles, penetrant dyes and the like,
thereby saving time and money. Furthermore, the information on the actual presence of
active defects can be used to increase the accuracy of normal NDT tests on the suspected
areas for a better evaluation of defects. Finally, if the electrochemical approach to
environmental cracking is adopted, it is often possible to find treatments which can minimize
or stop the cracking phenomenon; in such cases, AE will indicate immediately whether or not
such treatment is effective.
REFERENCES
1. C. Caneva, L. Giuliani, and A. Pampallona, Stress corrosion cracking inhibition
monitoring by means of electrochemical and acoustic emission measurements,
International Conference on Monitoring, Surveillance and Predictive Maintenance of
Plants and Structures, Taormina, Italy, 16-18 October 1989.
531
ABSTRACT
The recent development of electrochemical probes to monitor the first settlement of aerobic
bacteria on metal surfaces allows an optimization of biocide treatments in cooling water circuits.
Practical application to a steel mill cooling water circuit using contaminated seawater is described.
The reduction in chemical injection resulting from such monitoring favors the choice of a more
expensive but more efficient biocide compared to the common chlorine or hypochlorite.
Key Words: Electrochemical probes, aerobic bacteria, biocide treatment, cooling water
INTRODUCTION
Aerobic bacteria present in cooling waters tend to attach themselves to heat exchange
surfaces under favorable conditions.
The growth of bacteria colonies creates a
microbiological fouling of the surface which can support slime formation and higher forms of
life. The detrimental effects of biofouling are related to a reduction in the heat transfer
coefficient, an increased power consuption to maintain constant flow of water and to the
possibility of increased corrosion, especially on those materials which are sensitive to
localized modifications of the metal-solution interface. The formation and growth of
microbiofouling layers are highly dependent on water quality, especially in terms of amount
of organic matter, plant process conditions, contamination and season of the year. It is,
therefore, practically impossible to forecast what might happen in any specific heat exchanger
or steam condenser.
There are a variety of measures for biofouling control, but the most widely used one is
injection of a biocide, although also continuous mechanical cleaning or heat shocks are often
considered. The most popular biocide is chlorine, due to cost considerations; next to it, there
are its compounds such as hypochlorite and chlorine dioxide. Most of the other biocides
appear to be too expensive for large cooling water circuits. Chlorine tends to react with all
the organic matter present in water by formating potentially dangerous substances, and for
this reason, there is a growing concern over its ecological impact. Legislation already limits
the amount of residual chlorine allowed in effluent water, and in some cases, the length of
time during which discharge is permitted. Beside environmental problems, chlorination has
some operational difficulties of its own whether chlorine gas is used or local electrochemical
generation is preferred. It would be of interest also from an economical point of view to
reduce a biocide treatment to the minimum compatible with the design fouling factor.
533
BIOFOULING MONITORING
As microbiofouling is a complex function of many variables, it is of obvious interest to
detect when bacteria start attaching themselves to the metallic surface and how effective the
biocide treatment is in removing them. Development of biofouling sensors has been oriented
toward detection of the physical presence of a film (with optical means) or the measurement
of the heat exchange coefficient. Those methods, however, have produced cumbersome
and/or unreliable equipment, which are not really suited for long-term monitoring. A simple
and effective method of monitoring has instead been developed by studying the
electrochemical modifications produced by bacteria at the metal-solution interphase. It has
been experimentally shown that:
Bacteria colonies on metallic surfaces act like catalysts for oxygen reduction. The
increase in the oxygen reduction rate can be easily measured with an
electrochemical setup including a probe and an electronic instrument.
The readings of the instrument can be related to the percent of surface covered by
bacteria. An electrochemical biofouling probe can be used for continuous
monitoring of the cooling water and will detect the formation of the very first
layer of bacteria by showing a sigmoid increase of signal from a baseline (no
bacteria present on the probe surface) to a maximum (full coverage of the probe
surface by bacteria colonies). Injection of chlorine results in a drastic drop of the
probe signal, and the attainment of the original baseline value indicate complete
cleaning of the metallic surface.
Typical results in different locations are shown in Fig. 1 and clearly indicate the variance
of the phenomenon especially in terms of incubation times.
PILOT PLANT APPLICATION
In Livorno, Italy, ENEL runs a pilot plant reproducing a closed cooling tower circuit.
An electrochemical bioprobe was tested for more than 18 months in 1992-1993 and biocide
has been added as a function of the probe readings, with positive results. Bacteria counts in
the pit water used for this pilot plant have indicated that the probe starts giving a signal of
biofilm formation when bacteria are in the range 104-105/cm3.
POWER PLANT COOLING WATERS
Biofouling monitoring was applied to a number of power station cooling water circuits,
including well water and river or estuarine waters. Results from five different locations
indicated the immediate response of the electrochemical probe to the onset of biofilms, with
the only exception being one location where ferro-bacteria rather then aerobic bacteria were
present. A typical signal of the bioprobe, located in Tihange-2, Belgium, is reported in Fig. 2.
In another location, Dragenbos, Belgium, water comes from wells and has a high carbonate
content; thus, a periodic sulphuric acid injection is made to decrease scaling tendency. A
typical plot of the bioprobe signal against time reveals that the probe is sensitive to both acid
and unnecessary chlorine injections, showing a sharp peak for the injection duration. When,
however, a biofilm develops, the signal increases continuously and decreases when chlorine
is injected (Fig. 3). It is precisely this behavior of the probe signal that indicates the
effectiveness of the monitoring system:
534
Giuliani
Figure 1. Typical results obtained at different locations using the electrochemical biofouling
probe
535
Figure 2. A typical signal of the bioprobe which was located in Tihange-2, Belgium
536
Giuliani
537
When biofilm is present, the biocide injection will produce a sharp decrease in the
probe signal.
INDUSTRIAL APPLICATIONS
Since September 1993, a biofouling monitoring system has been in operation in the Ilva
Steel Mill, located in Taranto, Italy. The plant derives its cooling water mainly from an
internal sea (i.e., Mare Piccolo) which has only limited water exchange with the open sea.
The warm and biologically contaminated waters of Mare Piccolo are ideal for mussel
farming, and indeed, one of the farms is not more than 200 meters away from the plants
water intake. The simplified seawater cooling circuit is shown in Fig. 4 from the two intake
channels. After the filtering grids, the water is divided into four basins with different flow
rates (average values: 2 x 28,000; 27,000 and 41,000 m3/h for a total average of 120,000
m3/h).
Water first cools the steam condensers of the ILVA power plants, and then goes to two
basins from which the individual cooling water streams of the steel plant are fed. The initial
four basins are connected to the two intake channels by tunnels and a periodic observation of
the amount of biofouling on the tunnel walls is carried out. Some monitoring panels are used
to determine the biofouling rate and an average value of 60 kg/m2/year is obtained, with
surges up to 10-15 kg/m2/month during springtime. The seawater is treated with chlorine
dioxide by injecting this gaseous biocide into the initial intake channels before the filtering
grids.
Initial tests were made with a biofouling monitoring system including one probe, located
on the bank of one of the intake channels and fed with untreated water, and another probe,
positioned in a bypass on one of the mill cooling towers. The first probe indicates the
incubation and growth of the biofilm as a function of the actual water conditions (i.e.,
temperature, season, etc); this probe is cleaned when it reaches its maximum value. The
second probe is used to guarantee that no biofilm is formed from the treated water and is
never cleaned. Typical results from the first probe are reported in Fig. 5 and show how the
phenomenon is cyclically repeated on cleaned surfaces with different incubation times. A
typical result from the second probe is given in Fig. 6: the probe signal remains low for a
certain period of time after starting the biocide injection, then raises to a maximum where it
remains until treatment is discontinued. Due to the length of the circuit, the probe will see the
beginning and the end of the treatment with a delay, as is clearly shown in Fig. 6. After such
initial tests, a fully automatic monitoring system has been installed, and its use has greatly
helped in defining the proper injection schedule as a function of environmental variables.
Although local management is very cautious on this subject, a decrease of 50% in injection
has already been achieved, while progressive tests are still going on.
BIOGUARD INSTRUMENTATION
Based on the positive results obtained with electrochemical bioprobes, an automatic
instrumentation system has been designed to operate the biocide dosing pump automatically.
538
Giuliani
The instrumentation includes three independent water circuits (i.e., pump, flow meter, and
bioprobe) and three meters to read the probes. An additional electronic circuit generates a
signal to start the injection pump when anyone of the three bioprobes exceeds a preset
threshold, and a signal to stop the pump when all three bioprobes fall below another
threshold. Water is fed to the Bioguard instrumentation through a flanged 1"-pipe connection
and is discharged at the exit of the bioprobe manifold. The whole instrumentation is
contained in a steel cabinet, with an IP 65 protection rating. There are no external displays or
knobs as the meter panel is accessible only after opening the cabinet.
539
Figure 5. Typical results from the first probe used at the Ilva Steel Mill, showing how the
phenomenon is cyclically repeated on cleaned surfaces with different incubation
times
540
Giuliani
Figure 6. A typical result from the second probe used at the Ilva Steel Mill, showing the
changes in the probe signal as a function of time of the biocide treatment
CONCLUSIONS
The scientific observation that bacteria promote the oxygen reduction reaction on
metallic surfaces has been developed into an automatic instrumentation system to control
biocide injection into cooling waters. Extensive testing of this technique and debugging of
some initial unexpected results have resulted in a reliable system to minimize biocide
injection and to keep heat exchanger tubes clean from biofouling. The basic concept of this
biofouling monitoring system is to inject the biocide only to remove those bacteria which get
attached to metallic surfaces as opposed to the current practice of continuous or intermittent
water sterilization. This new concept guarantees that the minimum amount of biocide is
injected, with a resultant positive effect on costs and pollution. The reduction in the quantity
of biocide can also promote the use of more sophisticated products which have so far not
been economically competitive on the basis of extended dosages.
REFERENCES
1. A. Mollica et al., Interaction between biofouling and oxygen reduction rate on stainless
steel in seawater, 6th International Congress on Marine Corrosion and Fouling, Athens,
1984.
2. A. Mollica and G. Ventura, Electrochemical monitoring of biofilm growth and corrosivity
in Seawater: Effect of intermittent chlorination, 8th International Congress on Marine
Corrosion and Biofouling, Taranto, 1992.
3. L. Giuliani, On-line monitoring of aerobic bacteria to optimise chlorine injection, U.K.,
Corrosion 1993, Vol. 2, London, 1993.
541
ABSTRACT
Pipelines are generally externally protected against soil-side corrosion by a combination of
protective coatings and impressed current cathodic protection. For the protection of the internal area
of the pipelines, depending upon the corrosive tendency of the process fluids, corrosion control
measures are adopted in the form of inhibitor dosing.
Considering the inherent hazard posed in the event of the failure of pipelines, corrosion
monitoring of the external and internal surface is necessary for pipelines in spite of the fact that proper
corrosion control measures like protective coating and cathodic protection have been implemented.
Monitoring is required to ensure that all sections of pipelines are protected against corrosion (external
and internal) and also to assess the performance level of various control measures, and to thereby
ensure that the corrosion prevention systems, e.g., the cathodic protection and protective coating, are
performing adequately as intended and affording complete protection.
Various causes of pipeline failures are discussed, and the methods for ensuring the safety and
integrity of a system are described in detail. The capabilities and limitations of various techniques in
use for monitoring the effectiveness of corrosion protection systems and for assessing the health of
pipelines are discussed based on practical experience and established practice in the industry.
Recommendations for selection of a particular method and program of monitoring to ensure the safe
operation of a pipeline are also given.
Key Words: Pipeline integrity, cathodic protection, protective coatings, corrosion control
INTRODUCTION
A pipeline is generally externally protected against soil-side corrosion by a combination
of protective coating and impressed current cathodic protection. For protection of the internal
area of a pipeline, depending upon the corrosive tendency of the process fluids, corrosion
control measures can be adopted in the form of inhibitor dosing.
External corrosion protection coating is made up of an inner layer of fusion-bonded
epoxy and an outer layer of yard-applied, hot, extruded polyethylene (PE) coating with a total
thickness of 4 mm, or coal tar enamel coating (4-5 mm thick). Impressed current cathodic
protection consists of the required rectifier station with permanent anode groundbeds located
at predesigned intervals along the pipeline.
Considering the inherent hazard posed in the event of the failure of pipelines, corrosion
monitoring of the external and internal surface is a necessity for pipelines in spite of the fact
that proper corrosion control measures, like protective coatings and cathodic protection have
543
been implemented. Monitoring is required to ensure that all the sections of pipelines are
protected against corrosion (external or internal) and also to assess or monitor the
performance of various control measures, and to thereby, ensure that the corrosion prevention
systems, e.g., the cathodic protection system and coating, are performing adequately as
intended and affording complete protection.
Gas sweetening, in the case of sweetened natural gas high-pressure pipelines, does not
preclude the chance of internal corrosion due to fact that all gases carry a considerable
amount of condensate (i.e., slug). This condensate contains water. Condensate settles in low
lying areas of pipeline, and in the presence of oxygen, leads to corrosion of the internal
surface of the pipeline. Also, in the case of a crude oil, the internal surface of a pipeline
containing saltwater can suffer pitting corrosion. Many other factors like turbulence (leading
to erosion-corrosion), deposit attack, and impingement attack also lead to internal corrosion.
All of these conditions necessitate routine corrosion monitoring.
It is well known that all coatings, however superior, deteriorate with time due to ageing,
bacterial attack, water absorption and soil stress (which is very high in Indian soil) due to
climatic conditions and alternate wetting and drying. The degradation of a coating is
reflected in the fall in its electrical insulation property and mechanical damage which brings
the pipeline into direct contact with the soil, which is inherently corrosive due to presence of
water, Cl, SO4 and other ions. The corrosion, thereby, proceeds by either of the several
mechanisms described above.
The degradation of a coating has a direct influence on cathodic protection, since the
lower the electrical insulation property of the coating, the smaller the spread of cathodic
protection from each rectifier station due to the increase in the cathodic protection current
requirement to prevent corrosion. Further direct contact of soil and water electrolytes with
the metallic surface of a pipeline of areas of mechanical damage will lead to an increased
demand for cathodic protection current. This increase, which is 50-100-fold, always falls
below the current available in the system. Consequently the localized areas where the coating
has been damaged no longer receive cathodic protection, and thus suffer active corrosion
which can lead to pipe wall perforation within one year depending on the aggressiveness of
the soil. Attack on weld seams is characterized by bursts/rupture over several meters along
the longitudinal weld. Thus, the degradation of the coating in combination with the presence
of inherent holidays leads to active corrosion by soil electrolytes. The corrosivity of the soil
is directly related to the soils resistivity. A lower soil resistivity means a more aggressive
soil. Soil resistivities may vary from 300 -cm (i.e., extremely corrosive soil) to 10,000 cm (i.e., least corrosive soil) along the pipeline.
Even in areas of mechanical damage or degraded of coating in the form of tearing off by
soil stress, disbonding, large holidays which have brought soil into direct contact with the
pipelines surface, no corrosion will occur so long as the cathodic protection maintains a
minimum pipe-to-soil potential of - 850 mV when measured with reference to a saturated
copper-copper sulfate reference cell. In soils containing sulfate reducing bacteria (SRB), the
minimum potential requirement is -950 mV (with respect to copper-copper sulphate reference
cell) for adequate protection. Most cathodic protection systems are designed to cater to the
increase in current required due to the degradation of the coating or a fall in the spread of
protection (i.e., the influence of each T/R unit), but even with all of these design
544
Rajani
considerations, many sections of pipelines are without adequate cathodic protection, which
leads to active corrosion from the soil side due to unexpected coating damage or disbonding
during operation of the pipeline.
PIPELINE CORROSION MONITORING
Based on the above phenomenon and to enhance the health and integrity of a pipeline,
government regulations in Europe and the USA, as well as in India, have made the
monitoring of corrosion and various corrosion prevention measures mandatory at fixed
regular intervals to safeguard against major hazards due to pipeline failure.
The various tasks undertaken for assessing the integrity of a pipeline are as under:
545
ground survey techniques and is only likely to be found by intelligent pigging if noticeable
metal loss has occurred. As the pipeline ages, this cause of corrosion may become more
prevalent.
COATING SURVEYS
There are a number of coating evaluation survey techniques available for burned
pipelines. The main types of surveys are as follows:
(1)
where OL/RE is the Potential gradient from the defects location to remote earth in mV, and
PS is the pipe-to-soil potential in mV.
It is then possible to establish the severity of the defect. As can be seen from the
formula, the severity takes into account the size of the defect size and the available cathodic
protection current. From the % IR drop alone, it is not usually possible to determine the size
of the defect accurately because of variations in soil conditions and pipeline depth, but as a
guide, 6% IR represents a defect with bare steel being in contact with approximately 10 cm2
of soil at a depth of 1 m.
The following criteria are used to establish the severity of the coating defect from Eq. 1.
Less than 15% IR would not normally require coating repair work and would be
protected satisfactorily by the cathodic protection system,
Between 15 and 50% IR, requires general maintenance (within 4 years), and
More than 50% IR requires immediate coating repair/recoating.
CP Surveys
The only practical measurement of CP effectiveness is the pipe-to-soil potential. The
accepted criterion is a pipe-to-soil potential more negative than - 850 mV referred to a
copper-copper sulfate (Cu-CuSO4) reference electrode, or - 950 mV where SRB may be
546
Rajani
present. Because the pipelines pass through a wide variety of soil conditions, and because it
is not practical to test for microbiologically influenced corrosion, the criterion of - 950 mV
has been adopted. Providing this criterion is met, corrosion on the pipeline is expected to be
mitigated. The conventional method of monitoring has been to measure the pipe-to-soil
potential at approximately 1 km intervals with the current switched on. Providing all the
measurements have been more negative than - 950 mV, as given in international standards, it
has been accepted that the CP is satisfactory over the entire length of the pipeline. While
pipe-to-soil potentials measured at 1 km intervals may be acceptable, the potentials between
test points can vary significantly if there are distinct coating faults. The pipeline may thus be
unprotected at these locations. To locate these defects, pipe-to-soil potential measurements
should be taken along the entire length of the pipeline. This entails taking measurements at
1.5-5.0 m intervals, which is known as close-interval potential logging survey (CPL). With
the advance of technology, instrumentation and equipment for recording, large amounts of
data have now made it practical to conduct detailed surveys to identify areas of unprotected
pipe and provide an indication of where coating faults exist. This is particularly important at
faults identified by intelligent pigging, faults which may not be severe enough to warrant
immediate repair.
547
deficiency in the external corrosion protection system which was undetected with routine
monitoring is always detected with this method.
Coating defect,
Stray current effects, and/or
Soil variance.
Likewise, if the pipe-to-soil potential is too high (i.e., -1200 mV in the 'off condition
Cu/CuSO4 limit) then the pipe could be overprotected and accelerated coating degradation
can be expected from the excessive alkali generated.
Lateral Close Order Potential Survey
548
Rajani
This technique is identical to the CPL survey with the addition of a second half-cell
positioned 10 m laterally at right angles to the pipe (see Fig. 3). The potential differences are
measured from the half-cell over the pipeline to the test post via the training cable (V). The
potential difference is also measured between the two reference electrodes (U). Readings are
taken with the cathodic protection systems on and off giving U = UON - UOFF and V = VON
- VOFF readings from which a fault index, U/V, is calculated. This will indicate directly the
severity of the coating defect. The ratio cancels out the effects of soil resistivity and
attenuation. This technique has been extensively used in Germany.
549
The DCVG technique, like CPL, is directly related to the cathodic protection applied on
the pipeline. Other coating fault techniques like the Pearson technique and C-scan have no
such relationship to CP and lack the DCVG's ability to detect coating faults, especially in a
complex piping network.
A coating defect survey using the combined method is usually carried out as follows :
1. Conduct a DCVG survey and identify all coating faults,
2. Determine the defect size as gauged by the percentage of IR drop.
3. Using the CPL technique, measure the on and instant off potentials. The trailing cable is
also utilized to obtain the pipe to remote earth potential for the IR percentage calculation.
4. Perform a soil resistivity survey to correlate the corrosive soil conditions at coating defect
locations. A coating can have many faults and potential less negative than - 950 mV, and
if the soils resistivity is high, no corrosion will occur.
Based on the survey results, a comparison of the three coating defect survey methods
(i.e., the Pearson, C-Scan, and DCVG) on buried coal tar enamel-coated pipeline indicated
that DCVG detected nine defects, all of which when excavated were found to be actual
defects, and all of which when excavated were found to be accurate. The Pearson technique
detected three defects, while the C-Scan detected only two defects.
The DCVG technique will also identify the percentage of defect value so that only major
defects need be excavated. The combined CPL + DCVG survey can be carried out at a speed
of 5-8 km/day. The DCVG technique has both value and direction for the defect and can
pinpoint the exact spot where the current either leaves or enters the pipe.
Cathodic Protection System Monitoring
Cathodic protection monitoring is an important part of cathodic protection system
maintenance and operation. Cathodic protection performance monitoring at fixed, regular
intervals ensures that all the structures are receiving the desired protection against corrosion,
and that the total system is performing as intended in the design stage. In other words,
cathodic protection monitoring is aimed at the following two objectives :
Assessing the level of cathodic protection by measuring the structure-toelectrolyte potentials at various locations or points of the structure, and
Inspecting and assessing the performance of the major cathodic protection
equipment, e.g., the DC power source, T/R units, anodes, cables, junction boxes,
and insulating joints/flanges.
The various activities that are performed in regular monitoring are broadly classified as
550
Rajani
Any disturbance in the soil compaction over the anode bed. This would be
attributable to washing away of soil during monsoon, 3rd party construction
activity etc.
Anode groundbed resistance (to be maintained around 1.0 ohm).
Proper functioning of each individual anode so that each one of them is drawing
almost equal current.
In case the soil over the groundbed is very dry, arrangement should be made to
sprinkle water. Moist soil is required for functioning of anode bed.
Insulation Joint Test
Insulation joints should be carried out to check the effectiveness of the insulating flange.
551
Interference Tests
Cathodic protection interference is a source of great problems, and unless detected
during routine monitoring or a follow-up investigative survey, e.g., CPL, will lead to costly
pipeline failures, as has been experienced by many pipeline owners the world over. The main
forms of interference are as follows:
Frequency
Once every 3 months or
once/month at locations
of
under
protection,interference or
any other abnormality
Insulating flanges
552
Once/year
Remarks
Integrity of each test point should be
checked and any defects/ missing
components should be replaced.
Measurements should be taken at each
test point using a Cu/CuSO4 half cell.
Measure casing and career pipe-to-soil
potential values at each cased
crossing. Acceptable values casing to
soil-natural potential. Carrier pipe to
soil -850 mV (min), Cu/CuSO4
On/off potentials should be taken on
either side of insulating joint and
recorded to check performance of
flange joint for CPcurrent flow, if any
Rajani
Frequency
Initially and subsequently once in every
5 years
Pigging
Once/year
Investigative Surveys
Investigative surveys as given in Table 2 are required to be carried out initially after
taking over the pipelines, and subsequently at the frequencies given. These surveys are very
useful in identifying any major shortcomings which are likely to go undetected during routine
monitoring.
SELECTION OF MONITORING SYTEMS
Each of the various survey techniques described, provides information which, when
combined, provides a clear understanding of the condition of the pipeline. This must be
followed by a thorough economic study leading to the implementation of a remedial program.
Exposure of Test Coupons for Internal Corrosion
Test coupons exposed at different locations should be removed periodically for
inspection and determination of the corrosion rate on the fluid side. The iron count should
also be analyzed periodically in fluid to check the pickup of iron from the pipelines surface.
These tests will assess the internal condition of the pipeline.
RECOMMENDATIONS
It is recommended that pipeline be monitored externally to assess the CP performance
level and the condition of the coating by methods discussed to safeguard the line against
external corrosion damage by soil/water electrolyte and internally by fluid-side corrosion.
553
The choice of technique should be made after taking into consideration the pipelines
operating parameters, the type of CP, the pipelines characteristics, and the end result that is
desired from a particular technique.
All the results of corrosion monitoring, whether routine or follow-up (i.e., investigative
surveys), must be immediately checked and reviewed by an experienced corrosion engineer.
The comments and any corrective measures suggested by the specialist must be implemented
as early as possible.
REFERENCES
1. Harvey, Maintaining integrity on buried pipelines, Materials Performance, August 1994.
2. Leeds, A Critical Review of the Techniques Used to Delineate Pipeline Coating Defects
as a Precursor to Refurbishment.
554
ABSTRACT
In the Emirate of Abu Dhabi, there are many power and desalination plants spread over several
locations. Some of these plants are large and designed to produce 100 MG of water and 1000 MW per
day. Seawater for desalination and cooling is brought through large diameter pipelines and huge
pumps that work nonstop for years. There are different pumps to handle cooling water, fire water,
brine, distillate, potable water, chemicals and crude for such large plants. These pumps are made of
several alloys and metals, such as Ni-resist, stainless steel, and copper alloys, and corrosion failure has
occurred due to galvanic, stress and other factors. Maintenance by repair, coating and cathodic
protection are the subject matter of this paper.
Key Words: Power plants, desalination plants, pumps, maintenance
INTRODUCTION
In power and desalination plants where a variety of fluids are transported and stored,
hundreds of pumps are utilized which are manufactured by a dozen of international
companies. The fluids that are handled are:
Water such as seawater, brine, distillate, potable water, steam LP and HP, makeup
water,
Chemical dosing such as chlorine, hydrazine, caustic, acid, and
Fuel oil such as crude, diesel, and light oil.
The pumps are manufactured by leading companies like KSB, Kubota, and
Thermomechanica, and have been performing for several years.
Some of the pumps have been running nonstop for years, and as is the case with many
pumps, they have exhibited the following corrosion problems in some of their components.
555
Hosni et al.
Whenever the pumps were taken out for maintenance, a lot of barnacles was found
grown on parts of the pumps, in spite of chlorination (Fig. 2). The general place of failure in
most of the pumps is the shaft which is pitted; then strong vibrations sets in resulting in the
failure of concrete foundations. Does the small imbalance, combined with high velocity
cause the concrete to fail or was it the other way around ? In either case, the concrete
foundations have been restored, and the failure pattern of the pump was studied. Also, it is a
matter of concern as to how the barnacles grew on the components in swift water flows with a
high velocity.
558
Hosni et al.
Figure 4. Two photos of seawater supply pumps: (a) without CP; and (b) with CP
559
Pump Designation
Brine recirculating
2.
3.
Seawater recirculation
pump
4.
560
Distillate pump
Component
Material
Suction bell mouth
1.4404
Impeller
Pump shaft
1.4406
Driveshaft
Delivery elbow,
GGG-Ni.Cr.-Nb20-2
Diffuser, riser pipe,
Discharge cover
Barrel
MS 37.2, Rubber-lined
Delivery elbow, column GGG- NiCr-Nb-202
pipe, diffuser
Driveshaft, pump shaft
1.4406
Bell mouth
1.4404
Casing halves
GGG-NiCr-Nb-202
Pump shaft
Impeller
Shaft sleeve
Suction bell mouth
Diffuser
Delivery elbow, bearing
spider, riser pipe
Pump shaft, driveshaft,
impeller
Barrel
1.4406
1.4404
1.4136
G-Cu Sn10
G-Cu Al I0Ni
1.4404
MS 37.2
Hosni et al.
561
corrosion in one of the pumps, magnesium anodes were installed in the pool of water to
afford protection for the portion submerged in brackish water.
Cracking in the delivery elbow is a matter of great concern (Fig. 8). Some of the pumps
have been stitch-welded using castoline welding rods. In some cases, the repairs have been
successful, while in one or two cases cracks have extended in spite of extreme care being
taken during welding. Is this a material failure or an operational problem ? Two pumps
made by the same manufacturer, but fixed at different job sites, have exhibited the same type
of failure. Thus, the failure cannot be due to an operational problem.
Hosni et al.
repair by 50% ? In this case, since the shaft is made of stainless steel, the top portion could
act in an anodic manner when the pump is idle. It is not known whether the anodic effect
would be uniformly distributed, or if it would affect the flange end and cause more leakage.
Could an additional anode be placed inside ? Would this introduce more turbulence ? Could
stub anodes be inserted for impressed current CP ? What would be the current requirements ?
Is there a provision in casting for the placement of such anodes ? All these considerations are
shown in Fig 11.
563
for over 10 years and could easily work in this case. A schematic diagram of such installation
is shown in Fig. 12.
564
Hosni et al.
Function
Brine
recirculation
pump
Brine blow
down
Seawater
supply
Thermo
mechanica
Sea water
recirculation
Circulating
water pump
Cooling water
pump
T.W. Pump
Brine recirculation
Type
SEZT 1100
SELT 700-730
Distillate
pumps
Kubota
SEZT 11001080
SEL - 1200
Discharge elbow
95 C2 Ex78
Brine blow
down
Sea water
supply pumps
32C1E x A 53
Impeller
Seawater
supply
S.W.
Recirculating
Brine
recirculating
Repair Done
& Conclusion
Belzona not good
Hicoat
Elastometric
Welding and super
metal
metalock
Belzona SMAW weld
using (unsuitable
material)
Castoline x HD 2245
or Gricast 31
Belzona supermetal
1111
Welding (stitch) and
bolt
Weld/corrocote
Change to stainless
steel
(Weld with castoline x
HD
2245 or Gricast 31)
ASTMA 439 D2 cold
repair in some cases
Blasting and two coats
of
ARC 858 to 700
micron
Cavitation machined
and protection coating
MIG welding using
metrode ER 317L
Replace or belzona
Chesterton ARC 858
Coating
SMAW welding
DISTILLATE PUMPS
Distillate pumps are very different in design and operation. They handle water moving
from the distiller to the storage tanks through the ring main. Most of the components are
made of stainless steel.
565
Some of the pumps have been stifled and plenty of red deposits have clogged in. The red
deposits are copper carried away from the tube bundles. Copper collecting on stainless steel
could cause both galvanic corrosion and underside deposit pitting corrosion. Stainless steel,
once affected, could continue to corrode. Repairing by welding of the stainless steel shaft,
and machining and heat treatment are a matter of metallurgical skill. Cold repair is not
recommendable for stainless steel (see Table 2).
Could copper deposition be achieved at a different location before the distillate reaches
the pump ? Could galvanic steel in a sump, be placed far away from the pump so that copper
deposit could be filtered off or sumped out? These are some methods to be considered.
CONCLUSIONS
Although there are dozens of larger pumps and hundreds of smaller pumps in operation
everyday, only four different types are taken into consideration. The others handle chemicals
and other corrosive fluids, and corrosion failure is attributed to other reasons as well.
In discussed pumps, the occurrence of failure is typically at a particular location
irrespective of the material used. For example, in the seawater supply pumps, the most
affected component is the impeller while in the brine pump, it is the diffuser and the delivery
elbow that have repeated and acute failures. Cold repair and welding does not help in any
way. It has been recommended to use stainless steel instead of GGG or Ni-resist. But the
critical pitting potential of stainless steel at the temperature of brine is a matter to be
considered. In the case of distillate and town water pumps, copper deposition is to be
circumvented. In the case of seawater circulation pumps, only the lower casings have failed
although the top and bottom are of the same material. The failure is possibly enhanced by
casting defects and operational conditions. Cold repair is of no use. CP was successfully
tried in most of the pumps.
566
Kuwait University
P. O. Box 5469, 13060 Safat, Kuwait
3
ABSTRACT
An estimation of the cost of metallic corrosion in the State of Kuwait was determined for the
base years 1987, before the invasion of Kuwait, and 1992 after liberation of the country. The typical
cost of corrosion was represented by the data for 1987, and that for the year 1992 was for an abnormal
year since massive reconstruction and renovation of the basic industries in Kuwait were made.
Information was obtained via questionnaires distributed to the major industrial sectors in Kuwait,
official correspondence, and personal communication with key people in the different economic
sectors of the country.
For 1987, as the base year, the total cost of corrosion was estimated to be 5.2% of the gross
national product (GNP). Approximately 17.4% of the total cost (0.9% GNP) was avoidable, i.e.,
amenable to reduction by presently available corrosion-control technology. The estimated value of
resources such as materials, labor, energy and technical capabilities ascribed to corrosion-related
activities in 1987 were
Total cost to Kuwait
Avoidable costs
Unavoidable costs
KD 322 million
KD 56 million
KD 266 million
This study used a modified version of the input/output model of the Battle Columbus
Laboratories (BCL) and the National Bureau of Standards (NBS) of the US. The model quantitatively
identifies corrosion-related changes in resources, capital stock, and replacement lives of capital stock
for all sectors of the economy. The use of this model is well suited for estimating the total direct and
indirect costs of corrosion.
Key Words: Metallic corrosion, Kuwait, total cost, avoidable cost, unavoidable cost, input/output
model
INTRODUCTION
In the 1970s, several countries began to study the economic consequences of corrosion.
The findings of these major investigations indicated that the range of the estimated cost of
corrosion as a percentage of the gross national product (GNP) was 1.5-5.6 [1]. The
567
Corrosion Management
investigations approached the problem from two different directions. One of the first, and
probably one of the most important, studies published was the Hoar report [2] in the UK
which was based on statistics gathered from various industries experiences.. A different
approach was taken in the Bennett Report for the US [1], where the input-output analysis, as
developed by Leontief [3], was used. Based on this model, the entire USA economy, new
matrices, capital/output-matrix, capital life matrix, capital replacement matrix and new
demand vectors (personnel consumption and government) were constructed for the economy
in two worlds: World II (corrosion-free world), and World III (best practice world). The
differences between these two worlds and the existing world (World I) yield the total costs of
corrosion.
The present study adopted modified US approach, as it assesses the economic effects of
corrosion in a systematic framework. In addition, it estimates the direct and indirect cost of
corrosion for every sector of the economy.
Characteristics of Kuwait Economy
Traditionally, Kuwaits economy isheavily dependent on one sector as the main source
of income. The hydrocarbon sector is the dominant natural resource, as is reflected in its
contribution of more than half of the gross domestic product (GDP) in 1992, while the
agricultural and nonoil manufacturing sectors accounted for less than 4% of the GDP in the
same year. The public sector dominates the economic activities not only in terms of
ownership and management, but also in the employment of Kuwaiti manpower i.e. more than
90% of employed Kuwaities are employed by government. The private sector contributes
only 25% of GDP verss 75% for the public sector. Finally, the economy has an open policy
in term of the flow of goods, capital and labor in and out of the country [4].
MODEL SPECIFICATIONS
The assessment of the cost of corrosion requires a methodology capable of reflecting the
production processes of the various sectors in the economy and the interrelationships between
these sectors. One of the most suitable techniques is the input/output (I/O) analysis. This
techniques is capable of estimating the direct cost of corrosion and also the indirect costs of
inputs used to produce the inputs applied directly in the process of corrosion prevention and
control [5] and [6]. The model used in the study is quite detailed, it consists of 14 economic
sectors, each of which is represented by a production function consisting of the respective
inputs from each sectors plus value added. As a result, relatively detailed industry corrosion
cost data was incorporated into the model for simulation exercises.
This paper uses two I/O tables for the State of Kuwait. The first is the 1987 tables
produced by the Central Statistical Office (CSO) of the Ministry of Planning (MOP) [7]. The
second set of tables reflects the economy in 1992 and is an update for the 1987 tables using
the CSO's national accounts figures for 1992 [8]. The I/O tables of 1987 and 1992 have been
reconciled and aggregated into 14 economic sectors.
Structure of the I/O Model
The I/O model relies on the fact that total sectoral output is divided between intermediate
demand and final demand. It can be presented by the following equation:
X = AX+F
578
(1)
Al-Matrouk et al.
where
X = vector (14 x 1) of gross output
A = technical coefficient matrix (14 x 14)
F = vector (14 x 1) of final demand
To include the impact of corrosion on investment within the analytical framework,
investment has to be incorporated into the I/O inverse matrix and the basic model has to be
modified. This modification assumes a fixed investment output ratio, and can be
reformulated in the following form:
X = (I - A - N)-1 FD
(2)
FD = PC + GC + E - M
(3)
and
where N is a diagonal matrix representing the investment output ratio and FD is a stipulated
final demand (final demand less gross investment), PC, i.e., private consumption, GIC, i.e,
Government intermeridate consumption, E Gross investment,.and M export and import
respectively.
Equation 2 forms the modified I/O model which will be adjusted for World II and World
III to estimate the total, avoidable and non-avoidable costs of corrosion at the sectoral level.
This formulation assumes that the economy is growing at its long term growth rate.
Model Assumptions
The desirable model assumes that the economy operates at full employment or full
capacity. The rational behind this is that it allows us to measure the full potential capacity of
the economy, and thus, the full cost of corrosion. However, due to the special characteristic
of the labor market in the State of Kuwait, and consequently the difficulty of obtaining a
measure of full employment, this assumption was relaxed. Instead, the two I/O tables, i.e., for
1987 and 1992 were used in the exercise of estimating the cost of corrosion. The choice of
these two years was based on the availability of the I/O tables, as well as the state of the
economy during those years. In 1987, the economy was operating near full capacity, and
therefore, it is possible to assume that it was a case of full employment. On the other hand, in
1992, one year after liberation, the economy was operating for below capacity. Therefore, the
estimation of the cost of corrosion in these two year will provide us with two estimates; one
for the economy when operating at or near full employment and the second when the
economy is operating well below full capacity.
The main assumptions are implicit in the developed model are:
579
Corrosion Management
In addition, the modified I/O tables contain two rows: one for corrosions social savings
and one for value-added. These rows are below the "A" matrix, and therefore, do not directly
affect the inverse of the matrix.
Sectoral Aggregation of the I/O Model
The original I/O tables for 1987 and 1992 disaggregate the economy into 34 and 32
sectors, respectively. The aggregation process took into consideration the homogeneity of the
products in the aggregated sectors. The aggregation process was based on three conditions:
Inputs required to produce one Kuwaiti Dinars worth of output for each sector,
Replacement life of capital in each sector, or sectoral investment output ratio, and
a
Stipulated final demand for the output of each sector.
The methodology applied in the gathering of the data and information, required for the
model's adjustment, depended on three sources:
Data compiled from a survey specifically designed for industries in the State of
Kuwait,
Judgment of experts in the field of metallic corrosion in Kuwait, and
Experience of other countries and previous studies.
The first choice for data compilation was a questionnaire or the survey. However, if the
information for a specific sector or industry was not available from the survey or was of poor
quality, the analysis then depended on the second source, i.e., the judgment of the experts. In
the instances where the first and second sources were not sufficient, the study made use of the
third source to fill any gaps. This did not eliminate the possibility of using all three sources
580
Al-Matrouk et al.
together. On the contrary, in many cases, sectoral data were compiled from all three sources.
The questionnaire was the main source of information four important sectors: petroleum
refining; other chemical products; basic metal products; and agriculture, livestock and
fishing. As for the remaining 10 sectors, the analysis relied on the judgment of the experts in
metallic corrosion in the State of Kuwait, as well as, the literature, namely the US study [9]
and the Egyptian study [10].
The elements of corrosion that can affect the model coefficients and parameters are
The effects of the remaining elements of cost of corrosion on the model can be
represented by the input produced by the various sectors in the economy, and consumed, as
intermediate demand, by other sectors.
World II and World III
World II is a world free of corrosion, while World III is a world where the best corrosion
practice is applied universally. The comparison between WORLDII and World I, the world
as it exists, provides the total cost of corrosion. On the other hand, the comparison between
World III and World I indicates the avoidable cost of corrosion. The latter is this amenable to
reduction by presently available corrosion protection and control technology. This does not
imply a gold- plated world. It only implies that resources are used and allocated efficiently in
the process of controlling corrosion. The categorization of total costs of corrosion into
avoidable and unavoidable (i.e., the difference between total cost and avoidable cost) can
provide guidance in the allocation of priorities to research and development, legislative,
and/or educational efforts. Avoidable cost is influenced by the transfer of technology. On the
other hand, unavoidable cost is not influenced by the presently known technology, but
requires technological progress for further reduction in costs to be realized.
Adjustment for World III
After adjusting the "A" matrix to reflect the total cost of corrosion in World II, the
avoidable sector costs of corrosion were estimated as percentages of the total costs. The
criterion for this ratings was a qualitative comparison of producing sectors as to their
incentive or need to apply the best corrosion practices available and their flexibility in
applying them (i.e.,corrosion practice). The ratings range between 0.5 and 3.0. The
percentage of avoidable cost out of the total costs ranges from 5% for the sectors with the low
rating of 0.5, to 35%, for sectors with the high rating of 3.0. A low rating indicates that the
sector is not very sensitive to corrosion, and therefore, avoidable cost as a percentage of the
total cost of corrosion will be relatively small.
Model's Modifications
581
Corrosion Management
Mdifications were made for the two I/O tables, i.e., 1987 and 1992. The corrosion
saving parameters used in the construction of the World II and World III models, were more
relevant to the 1987 I/O table. Therefore, these parameters were used directly in the
development of World II and World III of the 1987 table. As for the 1992 model, it is
assumed that the Kuwaiti economy employed more efficient capital after the liberation, and
consequently, it is likely that the economy's corrosion-saving parameters are higher than their
levels before the invasion. Since the information available does not warrant reasonable
estimates of these parameters for the period following the liberation, the analysis considered
two scenarios for the I/O model in 1992. The first scenario assumed a 10% increase in the
corrosion-saving parameters over the levels used in the 1987 model, and the second scenario
assumed a 20% increase. In addition, Kuwaits I/O tables aggregate the economy's
investment in four sectors: other manufactures, construction, transportation and storage, and
other commercial services. To account for the impact of corrosion on investment, and to
calculate the investment-saving parameters, the analysis considered the three elements that
could affect investment: replacement of equipment and buildings, excess capacity, and loss of
product.
COST OF CORROSION IN THE STATE OF KUWAIT
The final results of the study with the model modified to represent World II and World
III, allow the quantification of the savings that can be achieved if corrosion did not exist (i.e.
the total cost of corrosion), as well as the savings that can be achieved if the best known
corrosion control practices were applied in every sector of the economy. These savings are
estimated on two levels: the macro level, which shows the cost to the economy as a whole,
and the micro-level which illustrate the costs to the various sectors in the economy.
Estimation of Total Costs of Corrosion
The total cost of corrosion can be estimated by comparing the GDP of the economy as it
exists with the GDP of a hypothetical economy where corrosion does not exist. Table 1
summarizes the results of estimated total, avoidable and unavoidable costs of corrosion in
1987 and 1992. The significance of the year 1987 is that the economy was operating near its
full capacity. On the other hand, the analysis of the year 1992 assumes that the economy
employed new, efficient capital after the liberation, and therefore, is more efficient with
respect to corrosion, which implies a reduction in the savings related to the cost of corrosion.
The analysis considers two scenarios for the 1992 model: the first scenario which assumes a
10% improvement in the corrosion-saving parameters over their levels in 1987; and a
resultant reduction in the total cost of corrosion, and the second scenario which considers a
20% improvement in the parameters.
The main results are summarized as follows:
1. The total cost of corrosion in 1987 amounted to KD 322 million, representing 5.2% of
the GDP. The avoidable cost was about KD 56 million, representing 0.9% of the
GDP. This is the cost that could have been saved if the economy had applied the best
corrosion practices available. The unavoidable cost of corrosion is estimated to have
been KD 266 million or 4.3% of GDP.
2. The costs of corrosion in 1992 were lower than those estimated for 1987. There are
three factors behind this decrease: the economy in 1992 was smaller than in 1987, the
582
Al-Matrouk et al.
1992 model assumed a more efficient economy with respect to the corrosion-saving
parameters, and therefore a lower cost of corrosion per unit of output and the
economy in 1992 operated below capacity, which means that only the more efficient
equipment was used in production processes.
3. The first scenario in 1992 suggests that the total cost of corrosion was KD 160
million, or 2.92% of the 1992 GDP. The cost that could have been saved if the best
corrosion practices had been applied, amounted to KD 40 million, representing 0.73%
of the GDP.
4. The second scenario, which assumed a 20% improvement in the corrosion-saving
parameters over their levels in 1987, had total and avoidable costs of corrosion
estimated at KD 140 million and KD 38 million respectively, representing
corresponding percentages of the GDP of 2.56% and 0.69%.
Table 1. Total Avoidable and Unavoidable Costs of Corrosion
1987
Total Cost
321,579
TKD % of GDP
5.21%
Avoidable Costs
55,929
TKD % of GDP
0.91%
Unavoidable Costs
265,650
TKD % of GDP
4.3%
TKD = thousand Kuwaiti dinars
1992 Scenario I
160,033
2.92%
39,991
0.73%
120,042
2.19%
1992 Scenario II
140,303
2.56%
37,945
0.69%
120,358
1.87%
Each of these indicators is significant and plays an important role in comparing the
various sectors. Tables 2, 3 and 4 list the eight indicators for the 14 sectors in the economy in
1987, 1992 scenario I, and 1992 scenario II. The main results can be summarized as follows:
1. The oil sectors, petroleum refining, and crude petroleum, are the most important
sectors in the Kuwaiti economy. In 1987, while these two sectors represented 47% of
583
Corrosion Management
2.
3.
4.
5.
6.
7.
8.
9.
584
the economy, they were responsible for only 6% of the total cost of corrosion (both
direct and indirect) estimated for that year.
The total cost of corrosion in the oil sectors amounted to KD 19.2 million, of which
KD 3.1 million could be saved if the best corrosion control practices available were
applied. In terms of the cost permit of value added, the total and avoidable costs of
corrosion represented 2.2% and 0.4% of the value added to the oil sectors,
respectively. In other words, 22 fils and 4 fils for every KD 1 of output.
In 1992, the oil sector constituede 38% of the countrys GDP. The first scenario for
1992, suggests that the total cost of corrosion in the oil sector is estimated to be KD
13.8 million, or 8.6% of the total cost of corrosion in the economy, of which KD 2.7
million could be considered to be avoidable or reducible. This latter amountaccounts
for 6.7% of the sum of the avoidable costs in the economy.
For every one KD.1 of output in the oil sectors, 26 fils are attributed to corrosion of
which 5 fils can be saved by employing the best corrosion control practices available.
The comparison between the total cost in scenario I and II for 1992 indicates that with
a 10% improvement in the corrosion-saving (i.e, cost) parameters, the oil sectors alone
could save up to KD 1.7 million in corrosion-related expenses.
Among the 14 sectors, the other commercial service sector (sector 13) and the other
government, social and household service sector (sector 14) bear the largest portion of
the total corrosion cost. In 1987, these two sectors contributed more than 70% and
62% of the total and avoidable costs in the economy. The total cost and the avoidable
cost for the other commercial service sector amounted to KD 118.2 million and KD
20.7 million respectively.
The costs of corrosion to the other government, and social and household services
sectors are estimated to be KD 106.9 million and KD 14.0 million respectively. The
1992 simulations show similar but lower results. The difference between the first and
second scenario indicates that a 10% improvement in the corrosion-saving (i.e.,cost)
parameters could result in KD 5.8 million and KD 8.0 million reductions in the total
cost of corrosion for the commercial and government sectors, respectively.
As for the cost per unit of value added, the cost indicators for these two sectors
appears to be below average. These results suggest that the potential savings in these
two sectors are high, but the effort required to achieve them could be above average.
Some of the factors behind the high total cost of corrosion in the two sectors could be
the diversity of the sectors, in addition to the possibility that the participants in these
sectors do not consider corrosion to be a problem or are not aware of corrosion as a
cost.
The sectors with the highest cost per KD.1 of value added, are as follows: nonmetallic
products (sector 6) basic metal products (sector 7) construction (sector 10) and other
manufacturers (sector 8). The total cost of corrosion for all of these sectors together
was 15% of the economys total cost in 1987, and 25% in 1992 (scenario I). The
avoidable cost as a percentage of the economys total avoidable cost was estimated to
be 23% in 1987 and 41% in 1992 (scenario I).
Al-Matrouk et al.
Total Cost
Direct Savings
Dirrect & Indirect
Savings
435
22080
730
7340
1883
473
165
6650
2415
3915
1570
5904
27196
21070
101827
0.0150
0.0096
0.0167
0.0130
0.0504
0.0136
0.0381
0.0569
-0.0794
0.0250
0.0276
0.0321
0.0198
0.0163
0.0165
1761
8786
3585
10480
3252
8292
673
6452
-6125
34394
7258
17627
118203
106940
321579
0.0605
0.0038
0.0820
0.0186
0.0871
0.2384
0.1558
0.0552
0.2014
0.2196
0.1276
0.0958
0.0861
0.0827
0.0521
Avoidable (Reducible
Direct Savings
Direc
S
22
6624
73
2202
377
71
49
665
845
587
78
886
2720
2107
17306
0.0008
0.0029
0.0078
0.0030
0.0101
0.0020
0.0114
0.0057
-0.0278
0.0038
0.0014
0.0048
0.0020
0.0016
0.0028
585
18
142
34
167
63
208
36
113
-119
930
110
422
20665
1399
5592
Corrosion Management
586
Total Costs
Direct Savings
Direct & Indirect
Savings
Avoidable (Reducible
Direct Savings
Direc
S
320
15449
445
3451
1331
259
171
6485
5424
4611
1068
5177
20134
24630
88954
16
4635
44
1035
266
39
51
648
1898
692
53
777
2013
2463
14632
0.0135
0.0086
0.0150
0.0117
0.0454
0.0122
0.0343
0.0512
-0.0715
0.0225
0.0248
0.0289
0.0178
0.0147
0.0162
1016
7335
2145
6428
3458
4227
749
6179
1178
28228
2969
9684
56641
29794
160033
0.0429
0.0041
0.0725
0.0218
0.1179
0.2001
0.1499
0.0488
-0.0155
0.1377
0.0691
0.0540
0.0501
0.0177
0.0292
0.0007
0.0026
0.0015
0.0035
0.0091
0.0081
0.00103
0.0051
-0.0250
0.0034
0.0012
0.0043
0.0018
0.0015
0.0027
11
154
20
113
94
106
65
607
99
890
50
265
940
580
3999
Al-Matrouk et al.
Total Costs
Direct Savings
Direct & Indirect
Savings
Avoidable (Reducible
Direct Savings
Direc
S
285
13732
395
3068
1183
230
152
5764
4821
4098
949
4602
17897
21893
79070
14
4120
40
920
237
34
46
576
1687
615
47
690
1790
2080
12896
0.0120
0.0076
0.0134
0.0104
0.0403
0.0109
0.0305
0.0455
-0.0635
0.0200
0.0221
0.0257
0.0158
0.0130
0.0144
905
6383
1907
5724
3001
3796
716
6674
1053
26163
2641
8797
50794
21749
140303
0.0382
0.0036
0.0645
0.0194
0.1023
0.1798
0.1433
0.0527
-0.0139
0.1277
0.0614
0.0491
0.0450
0.0130
0.0256
0.006
0.0023
0.0013
0.0031
0.0081
0.0016
0.0091
0.0046
-0.0222
0.0030
0.0011
0.0039
0.0016
0.0012
0.0024
587
10
142
18
104
93
96
59
619
87
861
45
255
873
527
3794
Corrosion Management
The objective of this paper was to quantify the costs and economic effects of corrosion in
the State of Kuwait, and to identify the sectors which suffer the most from corrosion. The
results indicate that corrosion has a significant impact on the economy, and that considerable
savings can be realized through the application of more advanced and new corrosion control
techniques. The main results and conclusions are
1. When the economy operates at or near full capacity, corrosion can cost the State of
Kuwait more than 5.2% of its GDP ( i.e.,KD 322 million in 1987). Given the present
technology, there is room for corrosion-related savings (i.e.,avoidable costs) of up to
KD 56 million, or about 1% of the GDP, by applying the best known corrosion control
practices. Furthermore, a 10% improvement in the corrosion-savings (i.e.,cost)
parameters, could save the economy up to KD 20 million, or 0.4% of GDP.
2. On the sectoral level, the estimates for the total cost of corrosion in the oil sector
(i.e.,crude petroleum and petroleum refining) was KD 19.2 million in 1987,
accounting for 6% of the economys total corrosion cost, and KD 13.8 million in the
first scenario for 1992, representing 8.6% of the economys total corrosion cost. The
avoidable cost, or the saving that could be achieved by applying the best corrosion
control practices available in these sectors ranges from KD 3.1 million in 1987 to KD
2.7 million in the first scenario for 1992.
3. The commercial services sector, and the government, social and household services
sector are responsible for the largest share of the cost of corrosion in the economy.
These service sectors accounted for 70% (KD 118.2 million, of which KD 20.7
million was avoidable) of the economys total cost for corrosion in 1987, and 62% in
the first scenario for 1992 (KD 106.9 million of which KD 14.0 million was
avoidable). The potentials for savings in the service sectors are high but they are not
easy to achieve.
4. The results also show that the nonmetallic products sector, basic metal products
sector, construction sector, and other manufacturers sector have the highest costs per
KD.1 of value added. This suggests that corrosion control efforts would be more costeffective in these sectors than in the rest of the economy.
5. Finally, it should be mentioned that the estimates represented in this study should not
be considered as absolutes, but rather as being the best available indicators of the
economic effect of corrosion. They provide a benchmark against which the relative
impact of other factors affecting the economy can be compared and assessed. This
can help in the development of a program for corrosion control which prioritize the
actions needed and the resource reallocation required.
GENERAL RECOMMENDATIONS
Due to the great economic losses incurred by corrosion to the nations economy, the
following recommendations are suggested to aid in reducing such cost;
1. All major industries in Kuwait should have at least one experienced corrosion
engineers with knowledge in corrosion protection and monitoring. These corrosion
engineers in staff should also assist in material selection during the design,
commissioning and operation of plants.
2. Institutional links should be developed between research institutions, such as the
Kuwait Institute for the Scientific Research and Kuwait University,and the major
588
Al-Matrouk et al.
3.
4.
5.
6.
REFERENCES
1. L.H. Bennett ed., Economic Effects of Metallic Corrosion in the United States, US
Department of Commerce, US Government Printing Office, Washington, DC, USA, 1978.
2. T.P. Hoar, Report of the Committee on Corrosion and Protection, Department of Trade
and Industry, London, U.K, 1971.
3. Leontief, Input-Output Economics , Oxford University Press, New York, 1986.
4. The World Bank, Kuwait Privatization Strategy, Vol. III, Macroeconomic Environment,
Labor Market and Legal Framework, Report submitted to the Ministry of Finance,
Kuwait, Confidential Document, 1993.
5. V. Blumer-Thomas, Input-Out Analysis in Developing Countries,: John Wiley and Sons
Inc, New York, 1982.
6. R.E. Miller and P.D. Blair, Input-Output Analysis: Foundations and Extensions prentice
Hall Inc., Englewood Cliffs, New Jersey, U.S.A. 1985.
7. National Accounts and Input-Output Tables, Central Statistical Office - Ministry of
Planning, State of Kuwait, 1987.
8. F. Al-Matrouk and J. Haieih, Economic Guide for the Selection of Industrial Project on
Sectoral Level in the State of Kuwait, Kuwait Institute for Scientific Research, KISR
Report, August 1995.
9. National Bureau of Standards, Economic Effects of Metallic Corrosion in U.S.A, Special
Publications 511, 1978 - 1, 2..
1.Egyptian Academy of Scientific Research Technology, Economic Effects of Metallic
Corrosion in Egypt, 1983.
589
ABSTRACT
In refinery, petrochemical, fertilizer, chemical and process industries; power plants and
metallurgical plants, control of corrosion damage by steam from medium and high pressure boilers is
of paramount importance to prevent corrosion leaks in condenser, condensate and steam lines. The
presence of parts per billion levels of aggressive impurities like O2, CO2 and Na may lead to
catastrophic corrosion failures in vacuum condenser, condensate and steam lines, and may ultimately
contaminate the condensate with ionic impurities and corrosion products. This results in wastage of
condensate/steam and energy, and costly condensate polishing operations. In this age of energy
conservation consciousness, steam and condensate lines are required to be perfectly protected by
controlling the quality of steam so that condensate with its sensible heat is returned to the boiler to the
maximum extent. Sources of corrosives are the boiler feedwater, ingress of gases through flanges and
atemperator in the post-boiler section and condenser leakage. Erosion-corrosion, cavitation and
impingement are other common causes of leakages in steam condensate circuitry.
Steam purity is primarily maintained through boiler feedwater (BFW) conditioning, e.g.,
effective deaeration of BFW, and chemical treatments through the use of oxygen scavengers and
volatile amines and effective monitoring of steam-condensate quality. In other instances, along with
boiler water conditioning, neutralizer and filming amines are injected into steam in the post-boiler
section. Varieties of volatile amine and filming amine combinations are available to prevent corrosion
in steam-condensate systems. Steam used for heating in process equipment in the hydrocarbon
industry becomes contaminated with oil and corrosion products. This contamination and leaks in the
vacuum condenser require that the unit be polished to remove various contaminants before the
condensate is returned to the deaerator. Polishing is carried out with the help of activated carbon, a
microfilter and ion-exchange. Control of the sodium carryover in the steam prevents sodium-induced
cracking problems in the welds of a steam-condensate circuit.
The selection of carbon steel piping and fitting the schedule to limit the velocity of
steam/condensate, as well as the provision of effective steam traps are the engineering measures
required to prevent erosion-corrosion, cavitation and impingement.
This paper describes, by means of a case history, the causes of corrosion damage in steamcondensate lines, and its prevention through chemical treatment, monitoring and design control,
condensate return and condensate polishing.
Key Words. Steam condensate, boiler, aggressive impurities, corrosion failure, chemical treatment
INTRODUCTION
581
Corrosion Management
Steam is primarily used in industries for heating process fluids, for catalytic reforming
and for distillation operations, beside being used for the generation of power. Steam
condensate is either discarded or recovered and reused. Turbine condensate is generally
clean, and is recovered completely and reused. The recovery of process condensate for reuse
depends on various factors such as process contamination, economics of recovery and
availability of spent condensate. In some processes like reformer, delayed coker unit
fractionator steam is consumed, and hence, it is not recoverable. With the increasing
emphasis on energy conservation, industries attempt to maximize recovery of as much
condensate as possible along with its sensible heat for reuse in steam generation.
The condensate contains dissolved solid impurities and dissolved gases. The presence of
oxygen and carbon dioxide causes corrosion in the steam-condensate system. Sodium in
excess of 20 ppb in steam has been found to attack welds at bends and elbows in steam lines.
In the plant, this post-boiler corrosion leads to cost penalties by requiring repairs to be made
to the steam-condensate system, with resultant losses of production and energy (through
steam leaks and deposition). A 1.5 mm diameter hole in a steam line causes 30 kg/hour and
65 kg/hour steam loss in 28 kg/cm2 and 60 kg/cm2 boilers, respectively, resulting in
corresponding losses of Rs. 1.0 lakh and Rs. 2.50 lakhs per annum. The losses due to steam
leaks of various sizes are given in Table 1.
Table 1. Steam Leaks versus Cost
Pressure
(kg/cm2)
1.5
7
14
28
60
8
15
30
65
33
62
119
248
530
987
-
25
-2110
-
4.75
8.90
17.14
Rs. 450/MT
(12.50US$/MT)
Rs. 36.0
Rs. 100.0 ( 110)
Rs. 1.0 Lakh
19.08
35.53
-
76.0
-
In post-boiler corrosion, the return of corrosion products along with the condensate can
result in the deposition of metal oxides on boiler heat-transfer surfaces which then bind the
boiler water slugs. These deposits have poor thermal conductivity, which leads to energy
582
Rajani
losses. Several chemical treatments are used to control oxygen and carbon dioxide corrosion.
A combination of chemicals offers the best protection. Controlling the sodium level in steam
prevents sodium-induced corrosion problems in steam-condensate circuitry [1].
When condensate is returned to the deaerator, the sensible heat in the condensate
increases the temperature of the feedwater which results in savings of energy and a lower
makeup water requirement.
Because of impurities and contamination, the condensate requires proper treatment-cumpolishing before being returned for reuse. Polishing units are operated when contaminants and
impurities exceed acceptable limits.
TYPES OF CORROSION
The types of corrosion generally encountered in steam condensate circuitry are [2]
Oxygen attack
Carbon dioxide attack,
Erosion-corrosion,
Cavitation, and
Sodium attack on welds.
Corrosion due to Dissolved Oxygen (O2)
Boiler-quality carbon steel material is generally used in boiler systems. A thin protective
coating of iron oxide (magnetite Fe3O4) forms at boiler temperatures, which prevents
corrosion. However, dissolved oxygen present in the system even in traces, can destroy the
protective coating resulting in rapid pitting-type corrosion. Oxygen pitting is often
accompanied by oxide deposits (rust hematite Fe2O3) or blisters near the pitted area. Oxygen
is a strong depolarizer of corrosion cells. This electrochemical reaction is quick because of
the high temperature in the boiler. Very often corrosion products are transferred to other
areas, including the boiler drum, where they cause insulating deposition. Figure 1 shows
typical pitting-type corrosion in a pressured hot-water system due to dissolved oxygen.
Apart from the feedwater, oxygen can enter the system through atmospheric leakage at
flanged piping and other sections under vacuum (such as the condenser which is kept at a
partial vacuum). Another source of oxygen is the leakage of oxygen-laden water through
condensate pump seals and surface condensers by the direct injection of quench water to cool
the condensate to prevent pump cavitation and the direct injection of boiler feedwater into the
atemperator.
Corrosion due to Dissolved Carbon Dioxide (CO2)
Carbon dioxide dissolves in condensate to form carbonic acid which is corrosive.
Carbonic acid corrosion is often seen as deep channelling, grooving or thinning at the bottoms
of pipes, and as penetration in threaded areas. It may also appear as uniform corrosion in
condensate lines where the flow is continuous. Figure 2 shows a condensate line before and
after CO2 control treatment.
583
Corrosion Management
Figure 1. Pitting-type corrosion cells in mild steel piping caused by dissolved oxygen
(1)
(2)
(3)
(4)
In most cases, the bulk of the carbon dioxide comes from the breakdown of feedwater
alkalinity (Eqs. 1-4). However, CO2 can also come from process contamination of the
condensate or decomposition of certain organic compounds.
In the steam and condensate system, the combination of oxygen and carbon dioxide may
be devastating. Corrosion proceeds more rapidly in such a situation, and the final reaction
releases CO2 which makes the process self propagating:
584
Fe + 2H2CO3 = Fe ( HCO3 )2 + H2
(5)
(6)
Rajani
Erosion-Corrosion
Erosion-corrosion occurs in the steam condensate lines due to local turbulence such as in
elbows and tees. This type of corrosion can also occur if the steam trap is defective and
unseparated condensate mists enter into the steam. Erosion-corrosion can be prevented by
preventing carryover of solids in steam and by installing correct steam traps.
Cavitation
When condensate flashes from a low diameter pipe into a high diameter pipe wall,
cavitation can occur. It can also occur on condensate pump impellers. Cavitation damage
can be identified by a honeycomb-type of pits with smooth rounded edges. Cavitation can be
prevented by installing impingement plates and selecting resistant materials for pump
impellers.
Sodium Attack
When the sodium content in steam is increased, welds at elbows and tees are attacked.
The attack is from surface cracks to deep cracks. The only way to prevent sodium attack is to
use high-purity water and all volatile boiler water conditioning chemicals.
(7)
If, rust is formed, sodium sulphite will react with the rust to form a protective magnetite
film
3Fe2O3 + Na2 SO3 = 2Fe3 O4 + Na2SO4
(8)
Each part per million of dissolved oxygen requires approximately 8 ppm of sulphite.
The addition of a catalyst such as cobalt will enhance the reaction of sulphite with
oxygen. Figure 3 shows the rate of the reaction of uncatalyzed and catalyzed sulphite.
Hydrazine (N2H4) is the most popular and effective oxygen scavenger used
conventionally in the steam and condensate lines of high pressure boilers. It protects
condensate lines from oxygen pitting. The reaction with oxygen is as follows:
585
Corrosion Management
N2 H4 + O2 = N2 + 2H2O
(9)
Neither the reactants nor the products are solids. Since Hydrazine adds no solids, it is
quite attractive for use in steam lines.
In addition to being an excellent oxygen scavenger, hydrazine also passivates active iron
and copper surfaces, rendering them, less susceptible to corrosion.
N2 H4 + 6Fe2 O3 = 4Fe3O4 + N2 + 2H2O
Reactive oxide film
Protective oxide film
N2 H4 + 4 CuO = 2 Cu2O + N2 + 2H2O
(10a)
(10b)
The addition of a catalyst to the hydrazine mixture ensures completion of the oxygen
scavenging and metal-passivating reactions (Fig. 4).
Organic Volatile Oxygen Scavengers
These are non-hydrazine, non-sulphite organic compounds that effectively remove
oxygen in boiler water systems condensate circuitry. They react in a volatile manner with
steam, and thus effectively protect the boiler drum, steam and condensate lines from oxygen
corrosion. The rate of oxygen scavenging is the same or faster than with catalyzed hydrazine.
The functions of this class of compound are similar to hydrazine.
These compounds have been introduced because hydrazine has been proven to be highly
carcinogenic and is banned in advanced countries. Organic volatile oxygen scavengers are
mainly proprietary chemicals and are manufactured by reputable water treatment chemical
companies.
Neutralizing Type Inhibitors
The neutralizing type of amines react with the carbonic acid in the condensate to form
neutral amine salts, thus raising the pH. The most popular of such amines are morpholine,
cyclohexylamine and diethylaminoethanol. Although not an amine, ammonia can also be
used.
586
Rajani
Figure 3. Reaction rates for catalyzed and uncatalyzed sodium sulphite for
a water temperature of 200C
Figure 4. Reaction rates for catalyzed and uncatalyzed hydrazine for a water
temperature of 200C
The distribution ratio (DR) of an amine is the most important factor and is expressed as
DR = Amine in vapor phase (steam)
Amine in water phase (condensate)
(11)
Amines with a DR > 1.0 have more amine in the vapour phase than in the water phase,
whereas amines with a DR < 1.0 have more amine in the water phase than in the vapor phase.
The degree of protection offered by these amines varies depending on the DR.
587
Corrosion Management
Table 2 shows the DR of ammonia and other commonly used neutralizing amines. These
amines are dosed at the outlet of the deaerator to maintain the pH of condensate at 8.5
(minimum) to prevent corrosion due to CO2. Neutralizing-type amines can reduce
concentrations of iron and copper that return to the boiler in condensate.
R - NH2 + H2 CO3 = R-NH3 + HCO3
(12)
Neutralizing Amine
Morpholine
Diethylaminoethanol
Diethylisopropanolamine
Cyclohexylamine
Ammonia
Typical Distribution
Ratio (DR)
0.4 : 1
1.7 : 1
1.7 : 1
4:1
10 : 1
Most Applicable
Condensate System
Short
Medium
Medium
Long or branched
Long or branched
Rajani
built-in backup protection, should there be condensate contamination or a system upset. The
optimum blend is also directly injected into the post-boiler section to prevent corrosion of the
steam-condensate circuitry. Proprietary formulations such as ELOGUARD are available.
ELOGUARD is multicomponent formulation which forms filming layer and conditions for
oxide film and offers protection to the entire system pre-boiler, it is nontoxic and provides
protection over a wide pH range. ELOGUARD is a polyamine formulation that has the
following components:
Corrosion Management
grade of granular activated carbon (AC). Primary and secondary AC units are employed.
The primary AC unit
590
Rajani
Corrosion Management
removes oil by a process of straining, and the secondary AC unit removes the residual oil by a
process of adsorption. After a period of use (once a year), the flow is modified such that the
primary unit becomes the secondary unit and vice versa. The AC in the secondary unit is
replaced with fresh AC, and the primary AC unit now retains its charge of old AC.
Table 3. Process Condensate Impurities (Typical)
Parameter
Unit
pH
Sodium, as Na
Calcium as CaCO3
Magnesium
as
MgCO3
Chloride as Cl
Sulphate as SO4
Silica as SiO2
Iron as Fe
Copper as Cu
Ammonia
Oil
Total dissolved solids
Polished Condensate
Quality Required
ppb
ppb
ppb
Process Condensate
(Petrochemical gas
Cracker unit)
8.5-9.5
40
55
35
ppb
ppb
ppb
ppb
ppm
ppb
ppm
ppm
35
80
30
20
0.1
0.06-1.3
20
270
5 max.
5 max.
5 max.
0.003
< 1.0
25 max.
6.5-7.0
5 max.
-
Process Condensate
8.0-8.50
1 mg/l
5 mg/l
4 mg/l
Polished Condensate
Quality Required
7.0
0.005 mg/l
0.003 mg/l
0.03 mg/l
< 0.01 mg/l
NIL
< 0.20 micromho/cm
< 0.05 mg/l
592
Rajani
upon the impurities, can be used in operation. The unit is attached to a cooler to cool the
condensate to 40-500C before it is fed to polishing unit.
593
Corrosion Management
594
Rajani
In the case of condensate containing colloidal iron, oil and/or other impurities, the
treatment scheme consists of
1. P.F. Pelosi and C.J. Cappablanca, Corrosion Control in Steam and Condensate lines,
Chemical Engineering, June 1985.
595
Corrosion Management
2. H. Uhlig, Corrosion Handbook, John Wiley & Sons Inc., New York.
596
ABSTRACT
A number of above ground storage tank bottom failures due to soil-side corrosion were
experienced and the causes were investigated. The existing deep ground bed-based cathodic
protection (CP) system was found to be inadequate due to the large scale drain of CP current to other
structures and the nonuniform distribution of current to all the areas of tank bottom. A number of
ways to improve CP systems performance were considered, and two types of improved CP systems
were implemented while a third type is under implementation. Use of correct monitoring practices is
critical and adequate facilities have been built for monitoring the true performance of the CP system.
This paper describes the implementation and operating experience of the improved CP systems
including the total CP system revamping plan for a large refinery tank farm.
Key Words.
Cathodic Protection, tank bottom, tank farm, monitoring, current density, current
distribution, interference, reference electrode.
INTRODUCTION
The Mina Al-Ahmadi (MAA) Refinery in Kuwait has over 170 above ground storage
tanks (AST) in the refinery tank farm located on the Arabian Gulf shore. The refinery has
been in existence since the early fifties, and major expansion and modernization were carried
out in 1984-85 converting it to a mega-refinery. The MAA tank farm stores petroleum feed,
intermediates and products at cryogenic, and ambient to hot service temperatures. Hence, a
variety of operating conditions exist. During the expansion programs, a large number of
ASTs and associated piping facilities were added leading to severe congestion of the tank
farm.
A series of tank bottom leaks led engineers to thoroughly scrutinize the existing cathodic
protection (CP) system for its effectiveness in controlling soil-side corrosion. The monitoring
practices were also evaluated for their applicability in the given environment. The severe
soil-side corrosion on some tanks within a short life of 7-12 years underscores the prevailing
highly corrosive environment and the urgent need to improve the CP system to mitigate the
corrosion.
EXISTING CATHODIC PROTECTION (CP) SYSTEM
Most of the tanks provided with CP operate at ambient temperature, while some store hot
products at 90oC. The tanks have two types of foundation. The first type is directly erected
597
Corrosion Management
on compacted soil with a 3 in. thick sand-bitumen mix pad. The second type is made on
annular reinforced cement concrete ring wall 1.5 ft width x 5 ft depth on which the tank shell
rests. The tank bottom sits on 3 in. thick sand-bitumen mix which is laid on compacted earth.
The soil side of the tank bottom was generally sandblasted and painted with coal tar epoxy
paint.
The tank farm is located on the Arabian Gulf shore where the water table is very shallow
(1-3 m) and an abundance of chlorides is found in the soil. A severely corrosive environment
is, therefore, present.
Most of the tank bottoms are protected by deep ground bed-based impressed current
cathodic protection (ICCP) systems. The ground bed consists of a string of 13 high-siliconchromium iron cast anodes located in a hole drilled to a depth of 200 ft with calcined
petroleum coke backfill. The deep ground bed is powered by a direct current (DC)
transformer rectifier (T/R) power source. A typical schematic diagram is given in Fig. 1. The
negative drain cables are connected to tanks in a variety of manners, sometimes directly and
sometimes through pipework. No electrical isolation is provided for the tanks or to any of the
systems. The CP system is, therefore, an integrated type in which all of the underground
structures are provided with simultaneous CP using a number of ground beds and T/R,
working in parallel circuit.
Permanent zinc reference electrodes were provided under the tank bottoms for the tanks
built during the refinery modernization plan and expansions, while other tanks had no
monitoring reference electrodes. The tank periphery is generally covered with 1 1.5 m of
sand-bitumen layer and no soil pots (test stations) exist for the monitoring of potentials close
to the tank bottom.
EXTERNAL CORROSION
Routine tank inspection in accordance with API-653 [1] revealed that many tank bottoms
are suffering from severe soil-side corrosion attack. The attack was very severe in the case of
tanks storing hot products (80-90oC). Severe corrosion of annular plates and adjoining
sketch plates leading to perforations and paper thinning was found in a short life of 8 years.
The corrosion rates are estimated to be in the range of 45-50 mpy.
An investigation into the existing CP system resulted into following conclusions:
Most of the tank bottoms are not protected by the existing deep ground bed CP
system.
The current output from deep ground bed anodes is diverted to the massive
underground structures installed during the refinery expansion. The presence of
sand-bitumen mix below the tank bottom only aided in large scale diversion of CP
current to other structures by offering higher resistance to CP current.
598
Jain et al.
Figure 1. Schematic diagram of the existing deep ground bed cathodic protection
599
Corrosion Management
The presence of foreign matter in the soil such as oil, bitumen and vegetation,
significantly influences the accuracy of CP potentials measurements.
Considering these factors, the main objectives of the CP system revamping were laid
down as
Jain et al.
Current density of 30 mA/m2 for ambient temperature service and 50 mA/m2 for
hot service (80-90oC) tanks with 25% extra for possible drainage,
Electrical isolation of tanks from break out piping to minimize current drain,
Uniform spread of CP current by distributing the anodes (as per Eq. 2below),
Mixed metal oxide coated titanium anodes with armored tail cables for system
longevity,
(1)
da = D / E.n
(2)
Corrosion Management
Jain et al.
Since in MAA the water table is very shallow, the Pr is normally negligible as compared
to the PS hence resulting in a spread efficiency of 2. The depth of each anode below the tank
bottom and the number of anodes are chosen to exceed the limit imposed by Eq. 2 for uniform
distribution of CP current to the entire tank bottom, with adequate overlap. A higher number
of anodes are normally installed for redundancy to cover incidental anode failure during the
design life of the system.
IMPLEMENTATION OF THE IMPROVED CATHODIC PROTECTION (CP)
SYSTEM
Perimeter-Based Cathodic Protection (CP) System
This system was chosen for two tanks, numbered TK-101 and TK-204, 59ft and 100 ft in
diameter, respectively. These tanks were newly built and located in an isolated area away
from the refinery complex.
The CP system consisted of a number of high-silicon Cr-canistered anodes located
around the tank periphery in a vertically drilled hole at 8 m depth with 3 m stand off from the
tank. The schematic CP system layout is given in Fig. 2. Although Cu/CuSO4 was the
preferred reference electrode, zinc was already installed under the bottom. Resistors and
shunts were included in each anode circuit for individual anode monitoring and current
balancing. The system was satisfactorily commissioned in May 1994 (even though the tanks
remained empty) and an instant off potential of -1.400 V was achieved at a current density of
1.18 mA/m2. Once the tanks were filled with product, protective potentials of -1.030 to
1.340 V instant off were achieved at a current density of 4.33 mA/m2. Detailed protective
potentials are given in Tables 3 and 4.
603
Corrosion Management
604
Jain et al.
The system has operated satisfactorily since that time with a very low current density of
1.34 mA/m2.
Under Tank Cathodic Protection (CP) System
Under the tank CP system was the answer for the tanks located in the refinery tank farm
and that come-up for rebottoming work. This CP system has been implemented for 3 tanks.
TK-820, a 192 ft diameter tank is a hot tank operating at 80-90oC. It was built in 1984.
The tank was originally provided with a deep ground bed CP system which failed to provide
adequate protection. Severe soil-side corrosion was observed on the annular plates and
adjoining sketch plates resulting in paper thinning and perforations (Fig. 3). Hence, the tank
was partially rebottomed in 1994. Making use of this opportunity, an under-bottom CP
system was installed by excavating around and drilling inside the tank for anode installation.
The CP system consisted of a number of mixed metal oxide coated titanium anodes
located inside the tank in a vertically drilled hole at a depth of 3.5 m with a 5 m stand off
distance from the shell. The water table was observed at a depth of 2 m. The monitoring
facilities installed were 3 Cu/CuSO4 permanent reference electrodes and 12 test stations at the
tanks periphery, very close to the shell. The control facilities included resistors and shunts
for each anode. The tank was electrically isolated from the connected piping by installing
flange isolation half kits. A schematic drawing is given in Fig. 4.
The CP system was commissioned in October 1994, and with the tank empty, protective
potentials of -0.89-1.2 V were achieved at a current density of 6.8 mA/m2. Increase in
current demand was observed when the tank was filled with hot product, and protective
potentials of 1.0-1.4 V were achieved at a current density of 13 mA/m2. The system has been
operating satisfactorily since that time. The details of the protective potentials are given in
Table 5.
Monitoring of the earthing system of the tank has revealed that there is no significant
interference.
Similar CP systems have been installed for two other tanks, TK-504 with an 80 ft
diameter and TK-753 with a 168 ft diameter. The results available from these tanks show
satisfactory performance of the CP system. Protective potentials of -1.05-1.20 V have been
achieved at a current density of 3.4 mA/m2, under empty tank conditions. The tanks are yet
to be commissioned.
Table 4. Protective Potentials, TK-204
605
Corrosion Management
Figure 3. Severe soil-side corrosion and perforation of a tank bottom plate (TK-61-821)
Table 5. Protective Potentials for the TK-820 Under Tank Bottom Cathodic Protection (CP)
System
606
Jain et al.
Figure 4. Schematic diagram of an under tank bottom cathodic protection (CP) system
607
Corrosion Management
608
Jain et al.
Corrosion Management
Figure 6. Typical schematic diagram of a grid type cathodic protection (CP) system
Jain et al.
Some successful accounts of the use of the grid type CP system are available in the
published literature. McJones [8] described two case histories where two 150 ft diameter hot
service (260oF) tanks have been satisfactorily protected with the grid type CP system. In this
case, the tanks are reported to be adequately protected with a 34 mA/m2 current.
The loop type CP system offers some of the same advantages as the grid type CP system.
The loop type CP system consists of a series of fully preassembled concentric loops of mixed
metal oxide coated titanium anodes with piggyback wire (Fig. 7). These loops are laid in
coke breeze backfill under the bottom with around 5 feet spacing. The major advantages over
the grid type system are greater spacing between loops, easier construction, and complete
absence of field joints thus enhancing anode reliability. However, more space is required for
the anode bed construction.
None of the tanks in MAA have secondary containment liners. The use of grid-loop type
CP is planned for three new tanks.
CONCLUSIONS
Deep ground bed-based CP systems could not provide effective CP for tank bottoms in
the MAA refinery due to the large scale diversion of the CP current to other underground
structures. No single type of CP system could be prescribed for the CP revamping of a big,
congested refinery tank farm. Optimal CP systems has to be selected from a number of short
listed options depending upon each tanks location, service, type, size and status with
consideration given to time, resources and cost constraints.
Uniform distribution of CP current to the entire tank bottom should be the primary
consideration for any CP system design. The traditional monitoring of protective potentials
near or around the tank periphery is not adequate and may even result in wrong conclusions
being drawn. Permanent soil pots free from contaminants located immediately next to the
tank bottom and permanent reference electrodes installed under the tank bottom are the
minimum essential for true evaluation of CP system performance. The observed protective
potentials must be corrected for IR drop in the soil, and it is felt that apart from the -850 mV
with respect to Cu/CuSO4 criterion, the other two criteria given in NACE-RP-01-69-92 and
NACE-RP-01-93 [9,10] should be applied from time to time.
An improved perimeter-based CP system has been installed for two tanks, and adequate
protection has been achieved with a 1.34 mA/m2 current. An improved under-tank CP
system has been installed for three tanks, and adequate protection has been achieved with a
13 mA/m2 current for the hot (90oC) tank and a 3.4 mA/m2 current for other tanks. Onstream installation of an angle-drilled CP system is planned for 25 tanks in the next two years,
while grid and loop type CP systems are planned for implementation for 3 new tanks.
REFERENCES
1. API-653, Tank Inspection, Repair, Alteration and Reconstruction, American Petroleum
Institute.
2. D.H. Kroon, Cathodic protection of above ground storage tank bottoms, Conference on
Above Ground Storage Tanks, MTI & NACE, Paper No. 29, January 1992, pp. 29/1 to
29/9.
611
Corrosion Management
3. T. Barletta et al., Taps storage tank bottoms fitted with improved cathodic protection, Oil
and Gas Journal, Oct. 23, 1995, pp. 89-93.
4. K.C. Garrity, Cathodic protection of external tank bottoms, Material Performance, April
1988, pp. 32-35.
5. J. Morgan, Cathodic Protection, 2nd edition, Houston, Texas, NACE, January 1993, pp.
237-238.
6. API-651, Cathodic protection of above ground petroleum storage tanks, American
Petroleum Institute, Washington, DC, April 1991.
7. L. Koszewski, Impressed current CP for new and existing tank bottoms with secondary
containment, Conference on Above Ground Storage Tanks, MTI & NACE, Paper No. 40,
January 1992, pp. 40/1-40/4.
8. S. McJones, Retrofitting storage tanks with double bottoms and improved CP for hot
service, Conference on Above Ground Storage Tanks, MTI & NACE, January 1992,
Paper No. 33, pp. 33/1 to 33/10.
9. NACE-RP-0193-93, External Cathodic Protection of On Grade Metallic Storage Tank
Bottoms, National Association of Corrosion Engineers.
10. NACE RP-0169-92, Control of external corrosion on underground or submerged metallic
piping system, NACE.
612
ABSTRACT
This paper addresses the problem of corrosion of ship structures. The main environmental and
operational factors affecting the initiation, spread and rate of corrosion of ship structures are given.
The main problems of general and local corrosion of cargo ships, bulk carriers and oil tankers are
briefly discussed. The methods commonly used to control and prevent the initiation and spread of
corrosion are briefly indicated. The consequences of corrosion associated with the degradation of the
strength of ship structures are stressed with particular emphasis on the buckling strength and stiffness
of plating panels. Parabolic and exponential models are assumed to represent the variation of the rate
of wastage with time of the buckling strength. The effect of uniform corrosion on the section modulus
and the inertia of stiffeners having different geometrical configurations are presented. The impact of
material wastage due to corrosion of the deck structure on the ship section geometrical characteristics
is examined. The effect of corrosion on the magnitude of the factor of safety and the probability of
failure is presented. Structural degradation problems associated with corrosion of HTS are clarified.
It is shown that ship section modulus, inertia, buckling strength and the flexural rigidity of panels
of plating could be significantly reduced in ships experiencing normal rates of wastage due to
corrosion. The deterioration of the geometrical characteristics of stiffeners could vary between 15%
and 38% depending on the section configuration.
Key Words: Corrosion rates, structural degradation, structural failure, material wastage
INTRODUCTION
Failure statistics reveal that corrosion is the most common defect in steel vessels and is
the dominant cause of structural failures for ships older than eight years. Corrosion of ship
structures results mainly from age, inadequate maintenance, the chemical or corrosive action
of cargoes, local wear of steel plating and sections, and improper structural design features
among other factors. A corroded steel plate is not only thinner but is also more brittle and is
thus more prone to initiating fatigue cracks. High stress concentration induces microscopic
cracks in the highly stressed parts of the steel structure. These cracks propagate into the
coating and act as pockets where corrosion action begins. It is, therefore, necessary to
eliminate any critical defects prior to service and to prevent noncritical defects from growing
to critical size during service. Local pitting can cause serious thinning of plates and sections
at critical, highly stressed areas. The cause of local pitting can be water condensation, lack of
cathodic protection, material defects, faulty preparation and treatment of the material, etc.
615
Corrosion Management
The deterioration of a HTS plate due to general or pitting corrosion will be more
significant than that of a mild steel plate having the same strength. Therefore, ships with
greater use of HTS will experience serious degradation problems in terms of buckling and
loss in fatigue strength. This will certainly impair the expected service life of the vessel.
Protection of the hull structure against corrosion is, therefore, crucial for the prolonged life of
ships. Higher values of wasted material may be accepted in certain areas for ships built to
scantlings higher than those required by classification societies. Such increased scantlings
are often used by owners to account for loss of material due to corrosion and to minimize the
amount of material replacement required throughout the life of the ship.
This paper, therefore, addresses the corrosion problem of ship structures with particular
emphasis on the impact of material wastage due to corrosion on the strength and stiffness of
stiffeners, plate panels and the geometrical characteristics of ship sections.
FACTORS AFFECTING CORROSION
Corrosion of ship structures represents one of the main causes of structural failure [1-3],
see Fig. 1, and is generally affected by the following factors: design, fabrication, protective
coating, operation, maintenance and repair, and environment.
78%
corrosion
8%
design &
workmanship
5%
fatigue
4%
excessive wave
load
5%
vibration
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
616
Shama
surface, contamination between coats, insufficient curing time, and poor handling of coated
surfaces.
RATES OF CORROSION
Corrosion occurs at a rate independent of plate thickness. The rate of corrosion of ship
structures varies with the ships age and type, the area of operation, and section of the ship,
i.e., bottom, vertical or top.
Several factors affect the rate of corrosion, such as type of corrosion, type of cargo
carried, presence or absence of sulphur, operating profile, characteristics of the environment,
treatment of the steel before painting, presence of water, frequency and extent of inspection
and maintenance, effectiveness of the corrosion control system, condition of coating, and
orientation of the surface.
The mean values of corrosion rates for the different ship types are given in Table 1.
These values are average values and are subjected to several sources of uncertainty.
Corrosion rates, however, could be significantly reduced by controlling the main factors
causing corrosion. Good flexible coatings could be very useful against stress-induced
corrosion. Inert gas systems are effective in reducing the rate of corrosion in tankers.
Cathodic protection, based on sacrificial or impressed current system is also used as a reliable
and cost-effective measure against corrosion of steel ships. The proper specifications of
coatings in the building stage may represent a crucial factor for reducing corrosion of hull
structure.
Table 1. Mean Corrosion Rates for Different Ship Types
Ship Type
General Cargo
Annual Rate (mm/year)
0.09
Oil Tankers
0.1
Ore Carriers
0.12
Bulk Carriers
0.17
CONSEQUENCES OF CORROSION
Corrosion of ship structures has a deleterious effect on maintenance and repair costs, hull
girder and local strength and service life [4,5]. The impact of corrosion on the structural
strength and stiffness of ship hull girders and local structural members are as follows:
Reduction of local and hull girder scantlings and load carrying capacity,
Increase of local and hull girder stresses and stress concentration,
Reduction of hull girder and local safety factors,
Reduction of local and hull girder flexural rigidity, buckling strength and fatigue
strength of structural connections
DESIGN CONSIDERATIONS
General
617
Corrosion Management
Deficient hull girder and local strength may result from errors in design, material,
fabrication and operation [1]. The main factor causing strength deficiency is structural
deterioration by corrosion. Deterioration by corrosion of welded steel connections may be
excessive around fillet welds. The effect of the quality of maintenance on the rate of strength
deterioration is shown in Fig. 2. Figure 3 shows the effect of corrosion on the shape of the SN curve. It is clear that uncontrolled corrosion of a ships structure could lead to a significant
reduction of the fatigue strength [6]. Bottom plating sustains a major portion of the hull
bending moment in addition to the local loads induced by hydrostatic pressure. Its strength
may be reduced significantly by general and localized corrosion [7].
Deck plating comprises a highly stressed portion of the ships hull girder and is of
critical importance to the longitudinal strength of the vessel. Corrosion of the deck structure
is expected to occur because of the frequent deck washing, water condensation, local deck
deformations, and mechanical abuse from deck cargo. Therefore, the deck plating should be
carefully examined for cracks, leaks, signs of excessive corrosion, wear and tear, and
buckling [8].
Ro
B
R(t)
Over Maint.
Good Maint.
A
C
SAFE
ZONE
Rm
Under Maint.
Ro = Original strength
Rm = Minimum strength
Time, t
FAILURE
ZONE
T
618
Shama
when the thickness of the plate panel experiences the normal wastage due to corrosion. The
effect of uniform corrosion of an angle section 200 x 100 x 13 mm in size on the section
modulus and inertia is shown in Fig. 7 and for an OBP section 430 x 20 mm in size is shown
in Fig. 8. The section modulus and inertia could be reduced by more than 25% for normal
values of material wastage. Figure 9 shows the deterioration of the section modulus with
time for three different section configurations. It is shown that the deterioration of the section
modulus and inertia vary between 15% and 38% depending on the section configuration.
This may have a significant impact on the magnitude and distribution of flexural and warping
stresses over the web and flange of the section, particularly for asymmetrical sections [9].
Log N
Figure 3. Effect of corrosion on fatigue curve
619
Corrosion Management
0.25
0.2
0.15
0.1
0.05
e / yo
0
10%
20%
30%
40%
50%
alpha
Rt /
1
0.9
Ro
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Parabolic Model,
Rt = Ro ( 1 - b.t )
b = 0.0006
b = 0.0007
Ro = original buckling strength of plate
Rt = deteriorated buckling strength of plate
0
10
15
20
Time , Years
Figure 5. Variation of buckling strength with time: Parabolic model
Rt
1
0.9
/0.8Ro
0.7
0.6
0.5 a
0.4
0.3
0.2
0.1
0
Exponential Model,
Rt = Ro.Exp.(- a t )
= 0.02
a = 0.005
10
15
20
Time , Years
F
Figure 6. Variation of plate buckling strength with time: Exponential model
620
Shama
0.9
610 x 13
0.8
200 x 100 x 13
0.7
Z / Zo
1.5
I / Io
Material
3 Wastage , mm
The increased flexibility of ship structures due to the extensive use of HTS or due to the
improper distribution of material over the ship section may cause local breakdown of
protective coatings and initiation of corrosion.
The effect of material wastage for a panel of plating on the flexural rigidity is shown in
Fig. 10 for three different plate thickness. It is clear from Fig. 10 that the flexural rigidity
could be significantly reduced when the plate panel experiences normal wastage due to
corrosion.
General Cargo Ships
For general cargo ships, corrosion occurs at several places such as the deck structure, the
lower part of the holds or twin deck frames, the lower part of transverse bulkheads, the aft
end of double bottom tanks and certain areas of tank tops where water is trapped due to
ineffective drainage systems [1]. Figure 11 shows the distribution of corrosion failure among
the different structural elements of the deck structure. Corrosion may aggravate and
accelerate crack and buckling failures of the deck structure.
621
Corrosion Management
For transversely framed ships, severe buckling of bottom plating within the midship
region may result from general and local corrosion. Figure 12 shows the distribution of
structural failure due to corrosion among the bottom structural elements. Such failure can
seriously impair the hull girder and local strength of the midship section. Structural failures
of the side shell plating due to corrosion may account for 66% of the corrosion failures of the
side shell structure. Transverse bulkheads between cargo holds experience excessive
corrosion in the lower boundaries and in the way of bilge wells.
High wastage occurs in ballast tanks and in inaccessible structural areas where
inspection and maintenance are difficult, such as the top parts of transverse bulkheads. Ease
of access to the various parts of cargo and ballast tanks is necessary if efficient inspection,
maintenance and monitoring is required.
Bulk Carriers
The structural failures of bulk carriers due to corrosion have been recognized and
reported in several papers [10]. The strakes of side shell plating between wind and water are
highly susceptible to severe uniform corrosion and localized pitting. This area is generally
subjected to high shear stresses [11,12]. High material wastage of these areas could have an
adverse effect on the shear buckling strength of the side shell plating, particularly for HTS.
Hopper, topside and double bottom tanks, ballast holds and void spaces are subjected to
excessive material wastage by corrosion. The tops of transverse bulkheads and the underside
of the deck structure are also subjected to severe corrosion.
Oil Tankers
Hull fractures and failures in oil tankers are generally attributed to detail design aspects
in areas of stress concentration at bracket toes and longitudinal connections to transverse web
frames [1,13]. The stress concentration factors at these connections are relatively high and
could represent a serious hazard when material wastage due to corrosion reaches
unacceptable values.
The rate of corrosion of oil tankers is significantly influenced by the following main
factors: tank washing, tank contents, tank atmosphere when empty, and presence of inert gas.
All parts of ballast tanks and transverse bulkheads between the cargo tanks and ballast tanks
are subjected to severe corrosion. The lower and top strakes of transverse and longitudinal
bulkheads are generally subjected to excessive corrosion. The deterioration of deck
longitudinals by corrosion may be more rapid and extensive than that of deck plating.
Wastage may reach 50% in some parts.
The use of HTS allows lighter scantlings and results in a more flexible structure. Greater
flexibility of the primary structure results in more load being shed to secondary structures.
Thus, the strength of the ship is more dependent on the integrity of the structure as a whole.
Excessive flexibility may also lead to fatigue problems. HTS structures exposed to stress
cycling at higher stress levels will have a shorter fatigue life than the equivalent mild steel
622
Shama
structure. Therefore, the deterioration of strength due to corrosion is far more significant for
HTS than for mild steel.
EFFECT OF CORROSION ON THE PROBABILITY OF FAILURE
It is evident that the deterioration of ships structural elements due to corrosion will
have direct impacts on the critical buckling strength, fatigue strength, factor of safety and
probability of structural failure. Figure 13 shows the variation with material wastage of the
factor of safety and the critical buckling strength of a panel of plating. The factor of safety
for flexural buckling is reduced by about 30% when the plate thickness experiences a normal
rate of corrosion.
623
Corrosion Management
624
Shama
7. The increased flexibility of ship structures due to the extensive use of HTS or due to the
improper distribution of material over the ship section may cause local breakdown of
protective coatings with subsequent initiation of corrosion.
REFERENCES
1. M.A. Shama, Ship structural failures: Types, causes and environmental impacts, AEJ,
July, 1995.
2. Y.Akita, Considerations for prevention of hull failure, NK Technical Bulletin, 1983.
3. M.A. Shama, Ship casualties: Types, causes and environmental impacts, AEJ, April,
1995.
4. ABS, "Guide For Vessel Life Extent", 1990.
5. Ship repair and conversion technology, Life extent: The problems and prospects, No.2,
1989.
6. SSC-318, SSC-346, Fatigue characterization of fabricated ship details for design, 1983,
1990.
7. Int. chamber of ship, Guide. manual for the insp. and condition assess. for tanker
structures, 1986.
8. ABS, "Guide For Vessel Condition Assessment And Reconditioning", 1991.
9. M.A Shama, Stress analysis and design of fabricated asymmetrical sections,
Schiffstechnik, September 1976.
10. ABS, Bulk Carriers: A Guide for concern, 1993.
11. M.A. Shama, Shear stresses in bulk carriers due to shear loading, JSR, SNAME,
September 1975.
12. M.A. Shama, Analysis of shear stresses in bulk carriers, Computers and Structures 6,
1976.
13. SSC-312, Investigation of internal corrosion and Corrosion control alternatives in
commercial tank ships,1981.
625
ABSTRACT
At the moment both the scientific understanding of corrosion processes and the engineeing
practices for corrosion control in process plants can benefit considerably from the development of in
situ on-line instruments for the characterization of surface films on construction materials. In this
paper, a new in situ contact electric resistance (CER) technique for the measurement of the electric
resistance of surface films on metals is described in detail.
The CER technique has been applied in several different research areas. These include
optimization of the chrome-plating process, prevention of localized corrosion of stainless steel,
investigation of the effect of inhibitors in crevice environments and monitoring of the kinetics of oxide
growth in high-temperature water.
Key Words: On-line monitoring, surface film properties, corrosion
INTRODUCTION
The role of surface films in corrosion, and more generally, in all surface-related
phenomena has become more recognized as new in situ techniques have evolved, and relevant
information has become available. For example, the properties of the surface film on Inconel
600 have been targeted [1,2] as the main area of research for mitigating stress corrosion
cracking in steam generators.
This work outlines the scope of industrial and scientific problems which have been
successfully encountered using the newly developed [3,4] contact electric resistance (CER)
technique. With the CER technique, the electric resistance of the surface film on a material is
monitored in situ. Electric resistance is a basic physical property of a material, and can be
used to extract a multitude of information on surface films. When used in industrial processes
for monitoring purposes, the measured electric resistance is positively correlated to important
variables such as onset of pitting corrosion [5], stress corrosion crack growth rate [6],
efficiency of particular gas mixtures in the oxidation of metals, and reduction of oxides or the
eddy current detectability of surface cracks in steam generator tubes [7].
Novel Techniques
In general, the electric resistance (R) of a material depends on the cross-sectional area of
the sample (A), the thickness of the sample (l), and the specific resistivity of the material (r),
according to the equation:
R =
l
A
(1)
In the CER method [3], normally two identical specimen surfaces are brought into
contact and then disconnected with a user-selectable frequency. When the surfaces are
disconnected, they interact with the electrolyte or gas. When the surfaces are in contact, the
resulting change in the contact resistance (R) is measured. Direct current is led through the
surfaces, and the resulting voltage is recorded. The contact resistance (R) is then calculated
from the voltage using Ohms law. The resulting resistance is the resistance of the surface
layer in the thickness, i.e., in the z-direction.
In another development of the CER method one of the two opposing identical specimens
is replaced by a probe made of iridium metal. This allows a more detailed analysis of the
electric properties of the surface layer [3]. Experiments with a further modification of the
iridium probe technique have shown that the resistance of the surface layer in the x-ydirection (i.e., the plane of the layer) is radically different from the resistance in the zdirection.
The design of the CER-instrument developed for measurements in high temperature
high-pressure process environments is shown in Fig. 1. In field applications, another design
can be used which fits into a 50 mm diameter penetration.
The maximum temperature achievable with the CER technique is above 1000oC in a
gaseous environment. In liquid environments, the maximum pressure and temperature are
limited by the specification of the pressure container typically to 20 MPa and 360oC.
The specimen surfaces have been standardized to have a diameter of 2.0 mm, although
other forms, such as tubes [8] can be used as well. The actual contact area depends on the
surface roughness and on the contact displacement (load) used. For the surface pretreatment
normally used, with the typical contact displacement of about 2 m, the load directed to the
specimen surfaces is roughly 2 N/mm2, and the actual contact area is 38% of the nominal
surface area. If the thickness of the surface layer is known, the specific resistivity () of the
surface layer can be calculated from Eq. 1. The resolution of the standard measurement
system is better than 10-7 . The movement is produced by a step motor, and it is
mechanically reduced to provide a displacement control accuracy of about 10-9 m.
MEASUREMENTS IN AQUEOUS ENVIRONMENTS
Some examples of the applications of the CER technique in various industrial and basic
science problems follow.
Basic Science
Figure 2 shows an example of a potentiodynamic scan for chromium in 1 M H2SO4 at
room temperature [9]. In addition to the polarization current, the electric resistance of the
surface film was monitored as a function of the potential. The polarization currents of Cr are
seen to correlate with the electric resistance of the surface film. This suggests that the
628
reactions occurring on Cr are controlled by electron or electron hole transfer across the film.
In the range -200...0 mV, the resistance had increased to a level of 1 . This corresponds to a
resistivity of 105 cm, if the thickness of the film is assumed to be 10 .
Novel Techniques
closed cracks by the eddy current technique depends on the electric resistance of the surface films
of the crack walls. The nature and resistance of the films which form on the crack walls during
operation depends on the composition of the solution inside the crack and close to the crack
location. During the cooling down of a steam generator, because of contraction and loss of
internal pressurization, the cracks are rather tightly closed so that the exchange of electrolytes and
thus changes in the films properties, becomes difficult. As a result, the surface condition
prevailing at high temperature is preserved. If the environment is such that the films formed on
the crack walls under operating conditions have low electric resistance, the eddy current
technique will fail to indicate those cracks or will underestimate their size. However, if the
electric resistance of the films is high, a tightly closed crack will resemble an open crack, and will
be easily indicated and correctly sized by the eddy current technique.
40
30
10000
1000
100
10
current density
10
R/Ohm
jCr / mAcm-2
20
0.1
0
0.01
-10
0.001
-20
-0.8
0.0001
-0.3
0.2
0.7
1.2
Figure 3. The apparent crack size (in percentage of the real crack) as
measured by the eddy current technique, presented as a function of the electric resistance of the surface film on the crack walls [7]
631
Novel Techniques
100
Brass
T = 45 C
-0.1
-0.3
0.1
Water 75 C
Wax removal
RESISTANCE / Ohm
-0.2
-0.4
-0.5
10
0.01
-0.6
0.001
-0.7
0
10
15
20
25
30
35
40
TIME / min
632
Air
Ar + 3% H2
RESISTANCE / Ohm
10
NICKEL
T = 300
0.1
0.01
0.001
70
80
90
100
110
120
130
140
150
TIME / min
633
Novel Techniques
Many processes, for example electroplating, are often preceeded by surface cleaning in
air by sandblasting or other techniques. Another example is the electronics industry, where
pretreatments are applied either to oxidize or to reduce the surface layers. In air exposures,
the kinetics of the oxidation/reduction processes as well as the electric resistance of the
oxides, is known to be very sensitive to variation in the airs humidity. Figure 7 gives an
example where oxidation of pure nickel was studied with the CER-technique in laboratory air
at room temperature.
1000
NICKEL
T = 25 oC
LAB AIR
100
RESISTANCE / Ohm
10
0.1
0.01
0.001
0.0001
0
10
15
20
25
30
35
40
TIME / min
634
1. P.L. Andresen and F.P. Ford, Fundamental quantification of crack advance for life
prediction in energy systems. Corrosion NACE96, Proceedings, Research Topical Symposia, pp. 51-99. NACE International.
2. R.W. Staehle, Bases for objectives of testing for steam generator tubing. Corrosion NACE
96, Paper No. 122, NACE International.
3. T. Saario, Development and applications of the contact electric resistance technique,
Dr.Tech. thesis, Helsinki University of Technology, Espoo, Finland, 1995.
4. T. Saario and J. Piippo, A new electrochemical technique for in situ measurement of
electric resistance and semiconductor characteristics of surface films on metals, Materials
Science Forum 185-188, 1995, pp. 621-628.
5. V.A. Marichev, T. Saario and V. Molokanov, Prevention of localised corrosion caused by
thiosulphate in paper mill environments, 12th International Corrosion Congress:
Corrosion Control for Low Cost Reliability, Vol. 2. Houston, Texas, USA, 19-24
September 1993, National Association of Corrosion Engineers (NACE), 1993, pp. 826833.
6. U. Ehrnstn, J. Lagerstrm, T. Saario, J. Piippo, P. Aaltonen, S. Thtinen, T. Laitinen and
H. Hnninen, Environmentally assisted cracking of Alloy 600 in PWR primary water.
Accepted for publication in Eurocorr96.
7. T. Saario and J.P.N. Paine, Effect of the surface film electric resistance on eddy current
detectability of surface cracks in Alloy 600 tubes, Proceedings, Seventh International
Symposium on Environmental Degradation of Materials in Nuclear Power Systems:
Water Reactors, Vol. 1, August 6-10, 1995, Breckenridge, Colorado, pp. 327-337.
8. T. Saario, S. Thtinen, J. Piippo and J.J.V. Kukkonen, In situ measurement of the effect of
LiOH on the stability of fuel cladding oxide film in simulated PWR primary water
environment. Proceedings, Seventh International Symposium on Environmental
Degradation of Materials in Nuclear Power Systems: Water Reactors, Vol. 2, August 610, 1995, Breckenridge, Colorado. Vol. 2, pp. 1231-1245.
9. G. Fabricius, T. Laitinen, J. Piippo, T. Saario, K. Salmi and G. Sundholm,
Electrochemical behaviour of chromium in sulphuric acid. Accepted for publication in
Eurocorr96.
635
ABSTRACT
Methods for monitoring nondestructive defects (e.g., cracks and corrosion deposits) are
proposed. Their application field includes corrosion process monitoring of pipelines and various
technological installations including those that are coated by protective layers. These methods are
based on probing monitored objects by radio frequency (RF) electromagnetic waves, i.e., by surface
electromagnetic waves. Different practically adopted, slow-wave structure (SWS)-based RF-sensors
have been designed for use in a real exploitation environment. Some peculiarities of SWS are
described and their application for testing corrosive objects are considered.
Key Words: Corrosion deposits, cracks, radio frequency monitoring, surface electromagnetic wave,
slow wave structure
INTRODUCTION
The corrosive processes of metal objects take an important place among factors that
determine the reliability and durability of their exploitation. There are many reasons for the
development of corrosion. Among them are stress-corrosion and ulcer corrosion, caused by
sulfur-hydrogen cracks; a lot of objects failures are connected with hydrogen cracking of
metals. The degree of that or other factors influencing the formation and development of
corrosion depends on concrete exploitation conditions and the aggressiveness of different
substances.
Monitoring corrosion processes is thus of great importance for many industrial and
transportation objects. Among them are oil and gas main-pipelines. They are subjected to
stress-corrosion, in particular resulting in possible environmental pollution and loss of
transported substances. Attempts to design measuring devices for testing crack development
on metal surfaces have resulted in the creation of sensors based on various physical
principles. These methods do not allow for proper decision on the problem of testing defects
on objects covered by protective, nonmetallic coatings without destruction of their integrity.
Such anticorrosive protective layers with thicknesses of several millimeters and more, do not
hinder the receipt of information with the help of microwave and radio frequency (RF) testing
techniques [1,2].
The methods proposed are directed at the monitoring of nondestructive defects (e.g.,
cracks and corrosion deposits) on pipelines and technological installations, including those
637
Novel Techniques
that are coated with protective isolation layers. These methods are based on the application
of RF electromagnetic waves (1-1000 MHz) for the probing of monitored objects.
SLOW-WAVE STRUCTURES POTENTIAL FOR CORROSION
PROCESS MONITORING
Great functional abilities are inherent to devices based on the use of surface (decelerated)
electromagnetic waves. Electromagnetic wave deceleration (slowing down) of hundreds and
thousands of times results in the RF-sensors size decrease, due to the miniaturization of
sensitive elements, made as a piece of the slow-wave structure (SWS), for example, a
meander-line or a helix (Fig. 1). Some positive peculiarities are inherent to SWS that allow it
to perform corrosion monitoring tasks on a new qualitative level. Among these peculiarities
are the following (Fig. 1):
a) meander line
b) helix line
Figure 2. Radio frequency (RF)-power (P) distribution near planar slowwave structures (SWS) surface (x-distance to SWS, z-SWS
longitudinal coordinate, -transverse distribution field
coefficient)
Surface wave specifics take place for various SWS-sensor forms (e.g., planar, circular
etc.). It provides the ability to concentrate RF-energy in needed, monitored areas. RF-wave
638
Pchelnikov et al.
639
Novel Techniques
backward net of the generator [2]. If it is necessary, the number of the monitored parts of the
object and sensors may be more than one.
640
(1)
Pchelnikov et al.
Novel Techniques
642
Pchelnikov et al.
Here, transverse coefficient ,t, characterizing surface wave field distribution practically
equals the phase coefficient b (b = 2p/ ls). These coefficients are related by the expression
2
= + k ( - j/wo)
(2)
where k = 2p/l is wave index for free space, w is angular frequency, eo is vacuum
permittivity, e is relative permittivity, and s is the isolating layer materials conductivity.
The deceleration index , n , equals b/k; therefore, from the above expression for b it is
seen that under the condition
2
(3)
The typical parameters e and s for the isolating layer are insufficient in order to influence the
value of b.
DESIGN OF SLOW-WAVE STRUCTURES (SWS) SENSORS
In most of the cases of practical interest, the surface of the monitored object has the form
of a cylinder or sphere, which makes it difficult to monitor with the plane sensor. This
drawback can be removed by designing a sensor with impedance conductors repeating the
geometrical form of the monitored object. For instance, in order to monitor a pipelines
corrosion state, a sensor made in the form of a dielectric channel 9 (Fig. 8) will be suitable.
Conductors 7 and 8, in the form of rectangular or oval logarithmic helices with oppositely
directed windings, are deposited on the inner and external surfaces of channel 9. Such helices
form results in an increase in the sensitivity of the depth measurement of cracks directed
along cylinders axis on the pipelines surface. Opposite directions of the helix conductors
windings provide, as was mentioned above, magnetic field energy displacement into the
isolating layer area and a high value for the slowing down index n. The latter results in the
ability to use relatively low frequencies (0.1-10 MHz) and the absence of influence by the
isolating layers parameters. The logarithmic form of the impedance conductors allows
receiving uniform distribution of the decelerated waves field along these conductors, which
provides the maximum value of sensitivity.
Novel Techniques
When a relatively large area of a cylindrical object should be monitored, the sensor can
be realized in the form of a channel. But in this case, impedance conductors 7, 8 on inner and
outer surfaces of the channel 9 should have meander-line form (Fig. 9). These conductors are
shifted in the longitudinal direction in half of the period T. The latter provides magnetic field
displacement into the isolating layer , 3 , and the reception of a high value for the deceleration
index , n. Here, the period T is chosen taking into account the needed depth of monitoring.
Pchelnikov et al.
Other types of measurement schemes may be also used. In one of them (Fig. 11), sensor
4s resonance frequency fr was measured by the dependence on corrosion process parameter.
This scheme contained a sweep oscillator ,12, detector unit ,13, and a frequency counter ,14.
645
ABSTRACT
Three main corrosion monitoring techniques are used to measure process fluid corrosivity. For
the majority of industrial applications, electrical resistance (E/R) probes and corrosion coupons (CC)
are most widely used, since these techniques can be applied to nearly all process environments. These
devices provide a basic measurement of metal loss, but require that a significant time base be used
before an accurate corrosion rate can be determined. In conductive electrolytes, the linear polarization
resistance (LPR) probe technique may be employed. This technique has the advantage of providing
instantaneous measurement of the corrosion rate, but because of its electrochemical nature, cannot be
applied in most process environments where monitoring is required.
Newer techniques seek to provide both the instantaneous corrosion rate information offered by
the LPR technique, as well as the universal applicability of the E/R technique. This paper describes a
new corrosion monitoring technology which achieves these objectives. Under trial testing,
sensitivities 400 times that of E/R technology have been apparent. For industrial monitoring
situations, this technology now approaches the instantaneous corrosion rate measurement offered by
the LPR technique. In addition, since the fundamental parameter measured by this new technique is
metal loss, it has the advantage of being applicable to all process environments.
Key Words:
INTRODUCTION
Weight loss coupons, electrical resistance (E/R) probes, and linear polarization (LPR)
probes have long been used to measure corrosion rates in industrial plants and equipment.
Both weight loss coupons and (E/R) sensors require considerable metal loss to take place
prior to producing a measurable response. Many days, or even weeks are required to sense
moderate changes in corrosion rates with any certainty.
Newer variants on the E/R technique apply excitation current to the actual pipe or vessel
wall, measuring the resultant potential field pattern. They show promise for use in
inaccessible locations, (e.g., subsea applications), but are two orders of magnitude slower in
response than conventional E/R probes [1]. Months, and sometimes years, are required to
obtain measurable results. Such historical data cannot be used in automated-feedback process
control systems.
647
Novel Techniques
The LPR technique provides rapid response; even small changes in the corrosion rate can
be detected within 5-15 minutes. However, LPR measurements are only possible in corrosive
fluids that are aqueous electrolytes. In addition to this limited applicability, LPR provides
relative data, frequently requiring expert interpretation.
Generally, traditional monitoring methods are either slow to respond, or are of limited
applicability and questionable accuracy. There is a need for a new monitoring method that
incorporates the speed of LPR with the accuracy and universal applicability of E/R or weight
loss measurements.
Cortest has developed a patented technique in which changes in the mass of corroding
metal elements are sensed as changes in the inductive resistance of the sensing element. Test
data shows a response time approximately 200 times faster than that of a corresponding E/R
probe. Corrosion rate changes on the order of 3-4 mpy are accurately detectable in less than
10 minutes. The following outlines initial test data comparing traditional monitoring
techniques with this new technology, i.e., MICROCORTM.
EXPERIMENTAL PROCEDURE
Response to Rapid Changes in Corrosion Rate
A recirculating system of tap water, flowing at 40 liters/minute was allowed to reach
equilibrium at ambient temperature (24.3C) and pressure. Commercially available E/R
probes from three major manufacturers were installed in the system, together with LPR
probes and MICROCORTM probes. The sensors were allowed to stand for 48 hours to
establish a stable corrosion product film, after which time, probe readings were taken at 60
second intervals using real-time LabviewTM data acquisition software.
After 180 readings (a period of three hours), during which baseline corrosion data was
collected, acetic acid was introduced into the circulation loop at a concentration level of 0.015
g.mole.1-1. Data collection proceeded for an additional 255 readings, at which point the
system was purged of acidified water, and replenished with conventional tap water at the
same temperature. Data collection proceeded for an additional 130 readings in the
replenished, less aggressive environment.
Temperature Sensitivity
E/R probes of both the cylindrical and wire-loop type were placed in a constant
temperature bath at 24C 0.5C, together with the MICROCORTM probe. The probes were
left for two days to ensure the establishment of thermal equilibrium and a stable corrosion
product layer, at which point the probes were read at four-second intervals. After a suitable
time period, the probes were rapidly transferred to another constant temperature bath
maintained at 17C 0.5%. Rapid data collection was maintained until the probe readings
indicated a full recovery from the temperature excursion. The probes were then rapidly
returned to the higher temperature bath, and the experiment was concluded by taking data
points until the probe readings again stabilized.
648
RESULTS
Corrosion Rate Measurements
Figure 1 shows comparative data from the MICROCORTM probe and a cylindrical
element, E/R probe. To aid in comparison, probe life is shown in volts as opposed to the 01000 probe life units used for conventional E/R readings. For the purposes of comparison,
two millivolts is equivalent to one probe life unit. The MICROCORTM probe clearly shows
two sharp discontinuities corresponding to the acidification of the solution, and the
subsequent purging of acid from the system. These changes approximate to an initial
corrosion rate of 12 mpy changing to 31 mpy and, finally returning to a low value of 4 mpy.
The E/R data shows no discernible trend, and gives no indication of extreme rate variations.
Novel Techniques
scale on the E/R data, which, in part accounts for the data scatter and the lengthy time lapse
required to discern corrosion trends using this technique. The temperature compensation of
the MICROCORTM probe, by contrast, is sufficiently rapid to produce no adverse effects in
its theoretical resolution.
Novel Techniques
Over the last four decades, manufacturers of E/R probes have introduced a wide variety
of element designs. Some improve sensitivity, such as the thin-walled hollow wires; others to
increase resistance to physical damage and increase element life, such as cylindrical elements.
The spectrum of element designs that fall within the practical limits of normal use are either
extremely insensitive, with concomitantly long response times, or comparatively sensitive,
fragile, and short-lived.
E/R probes have a useful life (span) equal to one-half of the element thickness (except
for wire elements, where the span equals one-quarter of the wire diameter). The span is
divided into 1000 probe units. Therefore, more robust (thicker) elements suffer from reduced
sensitivity as each probe unit represents a greater amount in metal loss. In addition, the
thicker elements have extremely low resistance resulting in a low signal-to-noise ratio. A 20
mil cylindrical element, for example, will take approximately 18 days to measure a change in
corrosion rate of 1 mpy. At the other end of the spectrum, a 4 mil hollow wire can detect a
corrosion rate change of 1 mpy in less than 48 hours. However, effective life of the 4 mil
element will be only one-tenth of the 20 mil cylindrical element.
The numbers given above assume perfect temperature compensation. Temperature
compensation is, however, a system variable. Systems in which temperatures change
extremely slowly, even if by large values (50-100C), permit the temperature of the E/R
probe's corroding and reference element to remain in equilibrium, and temperature
compensation is very effective. Systems experiencing large, sudden temperature swings may
require many hours for the sensor to recover thermal equilibrium, thus compromising much of
the data gathered by the E/R probe. The worst situation, however, is the system experiencing
small, but rapid temperature fluctuations. As observed in Fig. 4, such a system can impose a
temperature noise of 1-1.5% of the full scale on E/R data, thereby concealing resistance
changes due to corrosion effects.
As a consequence of this system-dependent temperature noise, the true resolution and
hence, response time of an E/R probe in any given system is nearly impossible to predict.
The rule of thumb of most manufacturers, which seems to work quite well, requires 1% of the
full scale (i.e., 10 probe units) change in probe reading to measure a real change in corrosion
behavior [2,3,4,5]. These changes can clearly be obscured by temperature noise. The
response times of various element types, at various corrosion rates, are illustrated in Fig. 5.
As shown, low to moderate corrosion rates are measured in hundreds of hours. Higher
corrosion rates provide faster response, but reduce sensor life to a few weeks.
LPR, being a direct measure of rate, provides a response time measured in minutes. The
only time lapse involved is that required for capacitive discharge at the electrode to take
place, allowing the true polarizing current to be measured.
However, LPR can only give an approximation of corrosion rate. The technique is based
on the Stern-Geary relationship [6].
V
i
BaBc______
2.3 (icor)(Ba + Bc)
(1)
where V is the applied polarizing voltage that is set in the instrument, and i is the
measured polarizing current. Provided the constant BaBc/(Ba+Bc) is known, the corrosion
652
current (icor) may be calculated and hence the corrosion rate. Unfortunately, the Tafel
constants Ba and Bc are system-dependent, and the constant BaBc/(Ba+Bc) may vary in the
normal spectrum of electrolytes by a factor of 3. Since it is tedious, time consuming, and
requires expensive equipment to precalibrate each system for the proportionality constant, all
commercial instruments contain an average constant. As a result, the absolute value of
corrosion rates measured by the LPR technique may be off by a factor of 150%. However,
relative measurements are reasonably accurate, provided changes in rate are not accompanied
by basic changes in mechanism. This question of accuracy, coupled with the need for a
continuous electrolyte as a corrosive fluid, poses a serious limitation to the applicability of
LPR, in spite of its advantage of rapid response [7].
653
Novel Techniques
Figure 6. Recent MICROCORTM data showing improved sensitivity with reduced noice
CONCLUSIONS
The MICROCORTM probe offers, for the first time, the possibility of making real-time
corrosion rate measurements in corrosive environments that do not present a continuous
electrolyte phase to the sensor. Such environments include many of the most critical in terms
of the economic consequences of unchecked corrosion. Among the more important of these
are oil and gas production and distribution systems, refining and petrochemical process-side
operations, cathodically protected structures, boiler feedwaters and condensates, and all
operations involving vapors and condensed moisture films. The rapid response of
MICROCORTM lends this technique to automated on-line process system controls.
Since the MICROCORTM technology is based on the measurement of properties related
definitively to mass, it will provide absolute data, and therefore offers advantages over the
more approximate LPR technique. The whole spectrum of cooling waters and aqueous
solutions encountered throughout the chemical process industries can now be monitored
accurately as well as rapidly.
________________________
MICROCORTM is a trademark of Cortest Instrument Systems, Inc.
LabviewTM is a trademark of National Instruments, Inc.
REFERENCES
1. M.W. Joosten, K.P. Fisher, R. Strommen and K.C. Lunden, Materials Performance, April,
1995, pp. 44-48.
2. Rohrbach Cosasco Systems, Inc., Bulletin No. 200-B.
3. Cormon, Ltd., GL 003, p. 4.
4. Cortest Instrument Systems, Inc., Bulletin No. 4.2, January, 1992, p. 6.
5. Petrolite Corp., Bulletin ERD-11.
6. M. Stern and A.J. Geary, Journal of the Electrochemical Society 104, 1957, p. 56.
7. E. Tiefnig, Method and Apparatus for Determining Corrosivity of Fluids on Metallic
Materials, United States Patent Application Serial #08/229, 449.
654
ABSTRACT
This study aimed at assessing the degradation properties of three different types of organic
coatings in laboratory-simulated 3% NaCl solution. Multilayer coating systems of coal tar epoxy,
modified epoxy and abrasion-resistant epoxy were investigated. A new electrochemical technique,
surface corrosion potential mapping (SCM), was employed to detect the surface potential changes
(variations in electrical conductivity) that occurred within the paint film. The surfaces of the painted
steel samples were also characterized with electrochemical impedance spectroscopy (EIS) and SEM.
The results indicated that SCM has the potential for use in the laboratory as a diagnostic tool for the
detection of paint defects or commercial paint quality with a higher degree of surface roughness.
Key Words: Corrosion potential mapping (SCM) technique, electrochemical impedance spectroscopy
(EIS), paint defects, organic coating, coal tar epoxy, modified epoxy, and abrasionresistant epoxy
INTRODUCTION
Electrochemical impedance spectroscopy (EIS) has been extensively used in the study of
the corrosion performance of organic coatings [1-3]. The technique involves the application
of a small AC signal across the coating/substrate system over a wide frequency range
(normally 8 to 10 decades). The magnitude and phase response signal can be used to obtain
information such as the capacitive and resistive behavior of the coating system.
Continuous monitoring of the impedance spectra for a coated metal enables
determination of the water uptake (in percentage of volume) by the coating system, and the
protective properties of the coating system.
The most up-to-date, and hence the most expensive, coating or insulation systems
gradually lose their effectiveness, and deteriorate and scale off sooner or later. It is well
known that small coating defects can be more serious than major coating defects. This is
because the anodic current density is much greater at the smaller coating defect. Moreover,
small coating defects can result in pipelines or tank bottoms developing holes within a
relatively short period of time. Thus, corrosion diagnostics is the basic determining factor of
the effectiveness of corrosion protection.
657
Novel Techniques
Husain
These coatings are several times thicker than those usually described in the literature.
The average thickness of the MP1, MP2, and MP3 systems were 450, 500, and 1000 m,
respectively. Furthermore, most of the reported research does not take into account the actual
service-life of the paint thickness.
Probe
(Calomel Electrode)
(Calomel Electrode)
Black Plastic Box
"Proximity Sensor"
Z-Direction movement
of Probe
X-Direction
movement of tray
Red Indicator
Green Indicator
Scanning
Electrode
Y-Direction
movement of tray
"SCM"
Plastic component
Diameter "1.5mm"
Sample
Tip
Dia.
80
micron
Secondary
Electrode
(Remote)
Sensor Socket
To OP-amp.
Electrolyte
Levelling screw
659
Novel Techniques
which ranged from 1 to 53 days. The AC impedance test data were taken at the open circuit
potential using three electrode arrangement.
Surface Corrosion Potential Mapping (SCM) Measurements
In this part of the study, an attempt was made to perform SCM on the ,UC, area of the
paint surfaces for the same paint systems (MP1, MP2, and MP3) following 53 days of
immersion in 3% NaCl solution. The test was performed on the UC area mainly because
there was no defect on the surface visible to the naked eye.
SCM scanning was conducted at a fixed distance of 10 mm from the borderline
separating the C and UC areas of the painted panel. The total area scanned was 100 mm2.
The total number of recorded potential scanning steps was 2000, that is, x = 50 readings, and
y = 40 readings. The total time taken per SCM scan was 1 hour, corresponding to 2000 steps.
The SCM test solution was 3% NaCl, made at the ambient temperature. An equilibration
immersion time of 30 minutes for each sample was used prior to making the electrochemical
measurements.
A schematic drawing of the panel is also included for the 1-cm 2 scanned area. The
location of the UC area scanned in the SCM is indicated on the sketch as A and B for each of
the paint systems.
Following the SCM, selected samples were examined using JOEL T200 scanning
electron microscope (SEM). The samples were cut and prepared to the recommended size.
They were first coated with carbon, and then gold coated to render the surface conductive
before microscopical examination.
RESULTS AND DISCUSSION
Figure 2a shows AC impedance data in the form of Bode plots. The data is associated
with the coal tar epoxy (MP1) paint system half-contaminated with 3% NaCl fine mist.
During the initial stages of immersion, the paint system appeared to be intact. Also, it had
little apparent porosity or delamination (blisters) on the C area at later stages of immersion.
An almost purely capacitive response was observed. This can be seen in the Bode plots
corresponding to 24, 48, and 120 hours of immersion. Apparently, there was hardly any
change during this period, suggesting that the system was relatively stable. Also there was
very little water uptake. Therefore, the anticipated corrosion occurring under this paint would
be extremely low. In fact, no visible signs of deterioration occurred, even with the presence
of a surface stimulating agent (in the form of NaCl) beneath the coating.
The impedance and capacitance data in Fig. 3a and b for coal tar epoxy are
representative of the responses of coating having little or no additional effects due to Faradic
9
(corrosion) processes. These values, when examined, would be greater than > 10 for paint
-11
film resistance (Rpf) and less than <10 for the capacitance values of the same paint film
(Cc).
The only visible sign of deterioration, observed after about approximately 600 hours,
was a small blister seen at the coating interface separating the C paint half from the UC paint
half. Even with this surface change in the paint film, the AC response maintained high
impedance values. This indicate good paint stability.
660
Husain
(a)
(b)
(c)
Figure 2. Bode Plots (log |Z| vs. log ) for the selected paints: (a) Coal tar epoxy
(MP1); (b) Modified epoxy (MP2); and (c) Abrasion resistant epoxy
(MP3)
661
Novel Techniques
Cpf in (F.cm^-2)
MP2
2.00E-10
1.50E-10
1.00E-10
MP1
5.00E-11
1.00E-14
10
MP3
100
1000
10000
Rpf
MP3
1.00E+ 10
MP1
1.00E+ 09
1.00E+ 08
1.00E+ 07
10
MP2
100
1000
10000
Key:
Cpf = Cc = paint film capacitance (Fcm-2).
Rpf = Rpo = paint film resistance or pore resistance (ohm cm2).
Figure 3. (a) Capacitance versus time, and (b) Resistance versus time, for the three coated
panels.
Alternatively, the Nyquist plot with the same impedance data depicts the change from a
slightly arced loop at 600 hours to a relatively complete semicircle towards the end of the test
(at 1272 hours). For paints of commercial quality, such trends in AC data are often observed
for relatively long periods of time. One significant finding in this study that confirms this, is
that highly impermeable systems can give similar impedance responses even after many
months of immersion.
The impedance responses for the modified epoxy paint system (MP2) having an average
thickness of 500 m, are shown in Fig. 2b in a Bode plot. The presence of an approximate
semicircle on the Nyquist plot was obtained just after 24 hours of immersion in the corrosive
662
Husain
electrolyte. An estimate of the impedance, in this case, could be made from measurements of
8
2
the semicircles dimensions, i.e., 1.6 x 10 cm . This relatively low value of resistance,
after only about 48 hours of immersion, indicated that this particular paint specimen suffered
from inherent microporosity. This was most probably enhanced by the presence of
appreciable amounts of surface corrosion stimulant agents (Cl- ions) deliberately added below
the paint film.
The inherent porosity further developed during the course of the experiment to such an
extent that after about 240 hours (10 days) of immersion testing, numerous blisters were
observed on the salt-contaminated region of the sample. The Nyquist plot revealed
semicircular plots with the frequency response in the low frequency parts having significant
scatter and intersection with the x-axis forming a complete semicircle.
The blisters continued to develop for about 288 hours of immersion. The system
7
2
impedance, at this stage, had decreased to 5.74 x 10 cm (Fig. 2b). This suggests that the
paint had degraded considerably. Indeed, some visual evidence of small ( 2 mm diameter)
blisters was apparent. The blisters covered most of the C region and extended toward the UC
area. The frequency response spectrum associated with this coating after 288 hours was
characterized by two relaxation times, representative of two RC networks.
There is some evidence that the MP2 system would not provide the same corrosion
protection capabilities exhibited by the other two coatings in this accelerated study. An
6
8
2
estimate of the frequency limit of the impedance lay between the values 10 to 10 cm
(Fig. 3b), which was in the range of the borderline between good and bad paints, i.e.,
unreliable according to the Bacon-Smith-Rugg criteria.
Observation of the data for the third paint system, that is, for the abrasion-resistant
epoxy-paint system MP3, with an average thickness of 1000 m, given in Fig. 3 along with
the impedance response in Fig. 2c plotted in the form of a Bode plot, indicates that the purely
capacitive behavior was dominated with a slope approaching -1, which was confirmed by the
presence of approaching a maximum value or 90. Furthermore, the response obtained
from this paint coating system indicates the existence of high impedance interfaces between
the steel substrate and the solution even in the presence of a surface stimulant. The surface of
the sample showed no visible signs of deterioration from blister formation either during the
experiment or at the end of the test. This suggests that the coating was intact and afforded
adequate protection to the underlying metal.
10
(Cc) value approaching 10 Fcm . Such trends in the impedance spectra are typical of data
obtained for thick, commercial-quality paints.
It has long been established that Cc increases as the level of water in the coating
increases [9]. Thus, the rate of increase in Cc should be proportional to the amount of area
delaminated by wet adhesion loss. This is indeed what is seen in the results depicted in Fig.
3a and b and the previously discussed complex impedance plots.
Figure 3a and b also shows that the Rpf values were higher for the thinner organic
coating (i.e., for MP1 with dft = 450 m compared to that of MP2 with dft = 500 m). This
663
Novel Techniques
means that the incidence of defects in the coating was independent of the coating thickness.
The reason for this is due to the failure of the coating at a single point, allowing the entry of
the electrolyte. This lowers the resistance considerably (as in the case of paint MP2, and to a
lesser extent paint MP1). If water invaded the coating more generally, an increase in
capacitance would remain at a constant rate without appreciably changing the resistance due
to the increased dielectric constant of the water ( as in the case of paint film MP3).
Surface Corrosion Potential Mapping (SCM) for MP1 After 53 Days of Immersion
The results of the SCM plots for each paint system are shown in Fig. 4. A schematic
drawing of the panel is also included for the 1-cm2 scanned area. The location of the UC area
scanned in the SCM is indicated in the sketch as A and B for each of the paint systems.
The blue end of the spectrum is cathodic and the red/yellow end is anodic when
presented in colored map. The potential scales attached to each map, are of the surface
potential value in mV. What is remarkable is the SCM plot result in Fig. 4a for coal tar epoxy
(MP1) made on UC area. The SCM map clearly shows that the surface of this painted sample
exhibited a surface film free of conductive paths or active anodic pores (i.e., no red/yellow
spots shown on the colored map). Moreover, the SEM qualitative analysis did not detect any
iron or show any sign of surface-deposited corrosion by-products. This confirms the
deduction made that MP1 had low electrochemical surface activities with no active anodic
sites.
Surface Corrosion Potential Mapping (SCM) for MP2 After 53 Days Immersion
The SCM maps of Fig. 4b for the modified epoxy (MP2) show evidence of active anodic
paths indicating the presence of micropores dispersed in the paint film. The SCM map also
indicates that most of the anodic active paths originated in greater density from the right-hand
side of the scanned surface. This is the region nearest the interface separating the UC area
from the C area of the paint film. The elongated shape of these active regions (depicted by
red and yellow in the colored map), could have been induced by the potential imposed by the
contaminated substrate across the C area, and may be caused by a lateral aqueous diffusion
under the paint film moving towards the UC area to the left of the borderline.
These diffusion effects were also confirmed with visual observation of many blisters of
different sizes in the UC area to the left of the borderline. In order to substantiate such
findings, a further set of SCM scanning tests were conducted on an area which was suspected
to have developed a blister. The location of the blister was just below the first scanned area
and to the left of the borderline (see schematic illustration in Fig. 4 marked B).
The SCM map shown in Fig. 4b displays the presence of large active anodic regions
located between x = 2 mm and x = 9 mm on the x-axis and between y = 2 and y = 6 mm on
the y-axis. This scanned area was then carefully cut and prepared for SEM examination. The
SEM photomicrograph (Fig. 4d) clearly indicates the presence of a surface blister. This SEM
photomicrograph confirms the observation made earlier with SCM on the same area in Fig.
4b.
A question may be raised in this particular situation about the causes of the surface
potential recorded with the SCM technique. The answer to this can be found by examining
the SEM photograph of the same blister (top of the blister) at a higher magnification. The
664
Husain
SEM micrograph shows the presence of many micropores, in addition to the deposits of
corrosion products film detected with SEM.
1 cm
1 cm
15 cm
MP2
"C" area
665
Novel Techniques
Figure 4. The SCM map with schematic drawings made for each scanned location (A, B), (a)
MP1, (b) MP2, (c) MP3, (d) SEM of a blister detected with SCM in (b), (e) SEM
of MP3 in (c)
Surface Corrosion Potential Mapping (SCM) for MP3 After 53 Days Immersion
Figure 4c shows the SCM results obtained for the abrasion-resistant epoxy (MP3) paints.
The map indicates the presence of active anodic sites, which are characteristic of microporous
paint films. It also shows deterioration trends as observed with the modified epoxy (MP2)
paint, but lesser than with MP2, and thus some decrease in the number of active sites.
SEM photographs taken from both the UC area as well as the C area (see Fig. 4e), reveal
similar surface morphologies. No distinctive effects were noticed on the contaminated paint
substrate in area C. Therefore, the active anodic site detected with SCM appears to be due to
active anodic voids created by the natural solidification of the glass flake pigmentation used
with such paint systems.
Therefore, the porous morphological image observed with SEM is the normal surface
microstructure of this paint film and was not caused by paint immersion degradation with the
3% NaCl solution. The formation of such a porous spongy morphology was due mainly to
the glass pigment volume concentration being higher than the binder or vehicle (i.e.,
exceeded CPVC). The SCM electrochemical data also showed that, although a reactive
anodic surface area was present for paint system MP3, no delamination processes occurred.
Therefore, in this case study, a good-adhesion metal coating resulted.
CONCLUSIONS
1.
The SCM developed in this study has significantly better resolution than earlier versions
of the scanning reference electrode methods.
2.
3.
4.
The micropores are believed to be responsible for the observed surface potential
recorded by the SCM technique. Therefore, the observed surface potential corresponded
to the partial anodic and cathodic currents originating from the electrolyte substrate
bridging through tiny pores on the top of the blisters.
5.
EIS and SCM were in good agreement in showing the coal tar epoxy (MP1) and to a
lesser extent the abrasion resistant epoxy (MP3) to be substantially more effective than
the modified epoxy (MP2) as marine paint systems.
REFERENCES
1.
666
Husain
2.
3.
4.
5.
6.
7.
8.
9.
K. Haldky, L.M. Callow and J.L. Dawson, Br.Corrs.J., 15, 1, 1980, p. 20.
H. Leidhesier, Corrosion, 39, 5, 1983, p.189.
H.S. Isaacs, Localized Corrosion, NACE, Houston, 1974, p. 158.
U.R. Evans, The Corrosion and Oxidation of Metals, London, Arnold Ltd., 1960, pp.
615-617, pp. 860-866.
H.S. Isaacs and N. Vyas, Electrochemical Corrosion Testing, (eds. F. Mansfield and U.
Bertocii), ASTM STP-727, 1981, p. 3.
R.S. Bassi, M.G. Hocking and S. Vasantasree, Proc. of the Nat. Corr. Conf. U.K.
Corrosion 90, Swindon Park, U.K.2nd Oct 1990, p. 249.
H.S. Isaacs and Y. Ishikawa, NACE, Corrosion/83, Anaheim, CA, 18-20 Apr. (1983), p.
25.
D.M. Brasher and A.H. Kingsbury, J. Appl. Chem. 4, 1954, pp. 62-72.
667
ABSTRACT
In the present paper, the advantages and limitations of holographic interferometry as a
nondestructive method of materials testing in the corrosion field are presented. Data on the corrosion
current density and the thickness of the oxide layer of anodized aluminum samples in aqueous solution
(0.5-3.125% H2SO4) are given. The corrosion current density and the thickness of the oxide layer of
anodized aluminum samples were measured by holographic interferometry as a function of elapsed
time. In general, the results show that as the thickness of the oxide layer of the aluminum samples
increases, the corrosion current density increases as well. Also, the results indicate that the optical
interferometry technique is a more conservative technique for measuring the corrosion current density
of aluminum samples in sulfuric acid than the weight loss method.
Key Words: Holographic interferometry, corrosion current density, aluminum, sulfuric acid, Al2O3
oxide film
INTRODUCTION
In recent work conducted by the author, a novel technique for monitoring the
mechanochemical behavior, i.e., stress corrosion cracking, corrosion fatigue, and hydrogen
embrittlement, of metallic electrodes in aqueous solutions has been developed [1-5]. The
technique incorporates holographic interferometry for measuring microscopic deformation
and electrochemical techniques for determining the corrosion current of metallic samples. In
addition, the author has recently reported mathematical models describing the cathodic
deposition and anodic dissolution of metals in aqueous solutions by holographic
interferometry [6,7]. Furthermore, the technique of holographic interferometry has been
applied to build an optical corrosion-meter for measuring the corrosion of different alloys as
well as to evaluate different epoxy-based coatings applied to protect metals against corrosion
[8,9]. Also, holographic interferometry is currently being utilized to monitor the pitting
corrosion of several metals in aqueous solutions and to measure the formation of an oxide
layer at a metal surface [10,11]. As a result, one may suggest that the techniques of
holographic interferometry have many useful applications yet to be explored in the corrosion
field.
The objective of the present work is to demonstrate the advantages and limitations of
holographic interferometry in the field of corrosion.
669
Novel Techniques
EXPERIMENTAL PROCEDURE
Metallic samples of a pure aluminum (99.7%) were used in this investigation. The
aluminum samples were fabricated in a cylindrical form 8 cm in diameter and 0.15 cm thick.
Then, all samples were polished and ground with silicon carbide papers until the finest grade
was reached. In order to be sure that the aluminum samples had a scratch-free surface, the
samples were etched with a chemical solution for 2 minutes at a temperature that ranged
between 85 and 95oC. The etching solution was made of 3 g/l of sodium hydroxide + 30 g/l
of trisodium phosphate. At the beginning of each test, the aluminum sample first was
immersed in the acid solution. Then a hologram of the sample was recorded using off axis
holography (Fig. 1) for the optical setup. In this study, a camera with a thermoplastic film
was used to facilitate recording of the holographic interferometry of the samples without
removing the samples from the solutions. The camera is an HC-300 thermoplastic recorder
made by the Newport Corporation. For more details on the procedures of the experiment,
the reader is encouraged to refer to the literature elsewhere [7,9]. During each experiment,
the holographic interferograms were recorded as a function of time, in which each test lasted
for less than 60 minutes. Then, the interferograms were converted to an orthogonal
displacement, i.e., an anodization process. Thereafter, the displacement measurements were
used to determine the thickness of the anodized films of the samples in 0.5-3.125 % H2SO4
solutions. Finally the corrosion current density of the aluminum samples was determined
according to the following mathematical relationship [7]:
J = F |Z| du
MT
where
J
K
|Z|
M
T
u
d
(1)
uniform interferometric pattern. Figure 2c is the same interferogram after five minutes. Here
22 fringes were recorded on the photograph. Figure 2d is the same interferogram after 7
minutes, where 29 fringes recorded on the photograph. Figure 2e is the same interferogram
after 12 minutes, and 36 fringes were recorded on the photograph. Figure 2f is the same
interferogram after 15 minutes, with 57 fringes recorded on the photograph. Each fringe
(dark line) in Fig. 2 (dark line) is equivalent to an orthogonal displacement of 0.3 mm
according to mathematical models reported elsewhere [7,8]. In other words, holographic
interferometry can be used as a powerful tool in the field of electrochemistry.
Novel Techniques
H2SO4. This behavior is interpreted by Faradays law in which the increase of the electronic
current reflects the increase of the mass gain or the increase of the mass loss on the metal
surface. In this case, it is obvious that there was mass gain on the aluminum samples because
of the anodization process. Furthermore, the data in the table show clearly that the corrosion
current density values determined by WL are independent from the increase of the thickness
of the oxide layer. In fact, the corrosion current density values measured by WL are
approximately equal to 1.0 mA/cm2 for all the investigated samples. In addition, the
corrosion data in the table show that the OI technique is a more conservative technique for
measuring the corrosion current density, of the aluminum samples in sulfuric acid than the
WL method. This is because the OI technique measures the corrosion current density by a
volume change rather than a weight change as in the WL method. In other words, the
corrosion current density values measured by OI are higher than those measured by WL by a
magnitude of 101. This occurred because the mass gain of the Al2O3 on the sample surface
had a different density than the substrate metal (Al). It is obvious that the corrosion current
density values determined by both methods would be the same if there were mass loss or
mass gain without any drastic changes in the surface chemistry of the samples. In such cases,
it would not make any difference if there was a volume change or a mass change on the metal
sample due to the fact that the density of the metal (surface and bulk) remained nearly
constant.
Table 1. The Corrosion Current Density of Aluminum Samples in
Different H2SO4 Concentrations
Solution
Concentration
(H2SO4%)
0.500
1.000
1.500
3.125
Film Thickness
J by OI
J by WL
(m)
44.15
9.00
31.50
36.20
(mA/cm2)
39.4
7.3
25.7
35.5
(mA/cm2)
0.80
0.83
0.76
0.65
REFERENCES
1. K.J. Habib, Holographic interferometry of a polarized and loaded metallic electrodes in
aqueous solution, Applied Optics 29, 13, 1990, pp. 867-869.
2. K.J. Habib, Initial behavior of corrosion fatigue/hydrogen embrittlement of metallic
electrodes in aqueous solutions, Experimental Techniques of Physics 38, 5/6, 1990, pp.
535-538.
3. K.J. Habib, G. Carmichael, R. Lakes and W. Stwalley, Novel technique for measuring
stress corrosion cracking of metallic electrodes in aqueous solutions: Theory and
applications, Corrosion 49, 5,1993, pp. 354-362.
4. K.J. Habib, Initiation of stress corrosion cracking of Ti90Al6V4 wire in aqueous solution:
Non-destructive monitoring by holographic interferometry, Optics and Lasers in
Engineering 20, 1994, pp.81-85.
673
Novel Techniques
674
Author Index
675
676
Subject Index
AC impedance, 659
Acceleration of corrosion, 45
Acid number, 101
Acidic soil, 472
Acoustic emission, 522
Aggregates, 362 (see Concrete)
Aggressive areas, 456
Algorithm for damage prediction, 19
Alloy
alloy 59, 235
aluminium 5083-O, 302
aluminum 6061, 507 (see Corrosion rate)
copper, 87
Alloying elements, 235
Aluminum
oxide film, 671
refining, 238
Aluminum-brass, 337
Ammonia, 78
Angle-drilled cathodic protection, 609
Anode, 551
Anticorrosive primer paints, 467
Application
industrial, 538
pilot plant, 534
Aqueous environments, 628
Aquifer, 158
Atmospheric residue desulphurization, 274
Austenitic alloys, 234
Bacteriostatic test, 151
Bandar Bushehr seawater, 302
Basic science, 628
Bicarbonates, 99
Biocide
effects of, 143
planktonic, 151
sessile, 152
Biofouling monitoring, 534
Biological corrosion, 325
Brackish water
high pressure piping, 84
high pressure pumps, 84
Brine
heater, 79
Chlorination, 291
679
copper-base, 55
cost, 2
dealloying, 54
detection, 549
effect of velocity, 69
fatigue, 524
management, 11
mass-loss under insulation, 44
monitoring, 12
nomogram, 92
polluted waters, 57
potentials, 22
processes, 45
product water, 76
resistance, 468
risk assessment, 5
seawater, 68
stainless steel, 58, 71
titanium,, 59
tube plates, 53
tube supports, 59
under insulation, 44
vapor-side, 60
Corrosion rate
aluminum 6061, 507
carbon steel, 503
temperature, 39
yellow brass, 505
Corrosivity
correlation, 229
prediction, 93
Cost
corrosion failure, 3
corrosion in the state of Kuwait, 572
corrosion, 2, 570
prevention and control, 3
over-protection, 3
CP surveys, 546
CPL survey, 547
Crack advance vs temperature, 168
Crack rate vs. stress-intensity factor, 253
Cracking, 277
Cracks in welded joints, 251
Crevice corrosion, 54, 56
seawater, 78
titanium, 73
Crude
chemistry, 229
oil type, effect of 102
Damage
680
analysis, 206
module, 27
parameters, 29
algorithm for prediction, 19 (see Algorithm)
deterministic prediction, 17
Demisters, 81
Design considerations, 617
Devanathan cell vs electrochemical testing, 170
Differential thermal analysis, 442
Dissolved carbon dioxide vs. corrosion, 583
Dissolved oxygen vs. corrosion, 583
Distillate pumps, 565
Dosing
biocide, 155
ferrous sulphate, 61
Downhole equipment, 224
Economy, Kuwait, 568
Effect of corrosion, 622
Effluent, 160
treatment, 238
Ejectors, 81
Electrical resistance, 512 (see Measurements)
Electrodeposition bath, 465
Electroplating, 632
Electro-vacuum test, 172
Emulsion paints, 461
Environment classification, 451
Environmental cracking, 522
Environments
aqueous, 628
gaseous, 633
Erosion-corrosion, 53, 57, 293, 585
Evaluation, bacterial, 155
Evaporator, 80
Event rating, 8
Exposure
test, 554
geometry, 42 (see Geometry of exposure)
External corrosion, 598
Factors affecting corrosion, 616
Failure analysis, 246
Failure cost, 3 (see Cost of corrosion failure)
Failures vs. oilfield, 2
Feed, 256
Film characterization, 466
Flue-gas characteristics, 21
Fractography, 280
Fundamental concepts, 18
Furnaces vs. corrosion investigation, 284
Galvanic corrosion, 294
Gas
composition, effect of, 97
velocity, effect of, 100
Gaseous environments, 633
Geometry of exposure, 42
Grid-loop type cathodic protection, 609
Groundbed inspection, 551
Guidelines for repair, 350 (see Repair)
Halogen emission vs. vapor-side, 74
Hardness, 286
Heat exchanger, 77
condensing, 24 (see Condensing heat exchanger)
Heat
recovery, 79
rejection, 77
transfer, 293
High pressure
cooler, 256
warm separator, 275
High temperature oxidation, 633
Holiday potentials, 476
Holographic interferometry, 671
Hull structural failure, 616
Hydrogen
blistering, 167
cracking, 524
diffusion, 168
embrittlement, 268
Hydrogen sulfide vs. temperature, 229
Impedance measurements, 388
Impedance response, 376
Implementation of cathodic protection, 603
Incoloy 800, 276
Inductive resistance, 517
Industrial
applications, 240, 538
areas, 455
Inhibition, 102
corrosion allowance, 106
Inhibitor vs. squeeze design, 132 (see Squeeze)
integrity 545
pipeline corrosion, 545
process, 638
MSF distiller, 51
Multi-stage flash desalination, 76
681
Jet impingement, 70
Kuwait economy, 568
Laboratory testing, 37
Lack of ductility, 247
Lattice trapping, 166
Life factor, 6
Linear polarization, 515
Localized corrosion, 217, 296
Low temperature oxidation, 634
Luminescence spectroscopy, 484
Management strategy, 11
Management corrosion, 11
Marine areas, 456
Mass spectrometric analysis, 419
Mass-loss corrosion under insulation, 44
Materials of construction, 227
Measurements
ac impedance, 659
corrosion rate, 649
electrical resistance 512
surface corrosion potential, 660
Mechanism vs. corrosion inhibition, 489
Metallography, 277
Metals processing, 238
Microbially induced corrosion, 291
Mitigation methods, 228
Mix water, 160, 362
Mixed potential module, 21
Model
specifications, 568
corrosivity prediction, 93
transmission line, 26
Module
condensed chemistry, 20 (see Condensed)
damage function, 27 (see Damage function)
mixed potential, 21
pit growth, 24 (see Pit growth module)
pit nucleation, 22 (see Pit nucleation module)
Monel vs. MEA solution, 498
Monitoring
biofouling, 534
cathodic protection, 550
corrosion, 12 (see Corrosion monitoring)
Naphthenic acid
corrosion parameters, 226
distribution, 229
Neutralizing type inhibitors, 587
Ni resist cast iron, 88
Nickel base alloys, 88
Nitric acid vs. corrosion behavior, 419
Nondestructive testing, 277
Oil tankers, 622
Oilfield failures, 2
Organic volatile oxygen scavengers, 586
Over-protection cost, 3 (see Cost)
Oxidation
high temperature, 633
low temperature, 634
Oxygen
cu base alloys, 71
effects of, 103, 386
scavengers, 586
Paper mill, 630
Parameters vs. damage functions, 29
Performance test, 551
Perimeter-based cathodic protection, 603
Phase compositions vs. weldments, 434
Pilot plant application, 534
Pipeline corrosion monitoring, 545
Piping, 81
Pit
depth, 378
diameter, 378
growth module, 24
nucleation module, 22
Pitting
corrosion, 323
damage functions for 304 stainless steel, 30
Planktonic vs. time-kill tests, 153
Polarization
behavior, 374
resistance, 390
tests, 303 (see Test)
Polluted seawater, 290 (see Seawater)
Pollution Control, 235
Portland cement, 362
Potential
measurement, 551
corrosion, 22 (see Corrosion potentials)
Potentiostatic polarization, 484
Power plant cooling waters, 534
Prevention and control cost, 3
Probability of failure, 622 (see Effect of)
682
Probability, 5
Procedures vs. simulated environment, 39
Process
monitoring, 638
operating, 60
Protection measures, 344
Pump
blowdown, 82
brine recirculation, 559
distillate, 82, 565
linkage, 201
seawater circulation, 562
seawater supply, 556
Rates of corrosion, 617
Rates of mass loss vs. cavitation, 313
Reactor, 264
Rectifier operation, 551
Reduced solvent emissions, 450
Relationships vs. flow and shear stress, 42
Repair of corrosion damage, 344
Replenishment vs. environment, 44
Research shuttle laboratory, 194
Resistance of steel, 211 (see Constant rate)
Retention coefficient, 409 (see Coefficient)
Reverse osmosis vs. selection of materials, 83
Rheology, 117
Risk, 4
assessment, 5 (see Corrosion risk assessment)
categories, 10
classes, 9
equation, 9
matrix, 9
modification, 9
Rotating
cage, 46
disc electrode, 495
Saline alkaline soil, 472
Sand, effect of, 78
Saturation index, 129
Scaling, 61
Scanning electron microscopy, 444
boxes, 52, 79
resistance of latices, 468
thinnable products, 461
vapor permeability, 468
wash role, 258
Waterborne
coatings, 454 (see Coatings)
products, 462
Water-cement ratio, 364
683
Weight loss
Test
hydrocarbon/liquid phase, 43
bacteriostatic, 151
method, 484, 494
constant strain stress corrosion, 304
Weldments, 434
insulation joint, 552
Worst-case scenario, 38
interference, 552
X-ray diffraction, 442
intergranular corrosion, 305
technique, 484
performance, 551
Yellow brass, 505 (see Corrosion rate)
planktonic time-kill, 153
polarization, 303
simulated-environment, 38
time-kill, 151
Testing vs. laboratory, 37
Time-kill test, 151
Titanium, 73, 87
Tool joint, 204
Total acid number, 226
Transformer operation, 551
Transmission line model, 26
Trap energy, 166
Treatment of process condensate, 590
Troubleshooting, 258
Tube plates, 79
Turbine condensate, 590 , 595 (see
Combination)
Types of
corrosion, 256, 583
oilfield treatment chemicals, 186
Vanadium vs. effect of temperature, 392
Vapor side
behavior of materials, 74
corrosion, 60, 74
Vapor spaces, 80
Velocity, 99, 227
vs. type of flow, 106
Ven diagram vs. stress corrosion cracking, 280
Venting, 81
Wall shear stress, 230
Wash water specifications, 276
Water
684