To Check the Number of HSDPA User allocated per cell:
LST UCELLCAC-----in RNC end 2. To Check the SCTPLNK & SAAlLNK: LST UIUBCP: 3. LST OP ADD OP (For Creating Account in RNC/BSc for Local login during M2000 Connecti vity down) 4 IRAT:3G to 2G handover Network reselection :2G to 3G handover. 5. LST Unode---To get node-B all info in RNC end 6. DSP UCELL---To check the status of Node-B cell(Result---Cell is Setup and ena bled) DSP UCELLCHK---to check traffic in RNC end BLK UCELL---to Block cell in RNC DEA UCELL--To Deactivate Cell in RNC. ACT UCELL--To Activate Cell in RNC UBL UCELL----To UBlock Ucell in RNC BLK Unode-B----To Block Unode-B in RNC UBL Unode-B----To Unblock Unode-B in RNC RST Unode-B----to Reset Unode-B in RNC PING IP--------To ping the Node-B Service from RNC TRC IPADDR------To check where we are getting drop in RNC LST UCELL------To get information about the Cell like PSC,Frequency,Transmitting Power,LAC,SAC,RAC in RNC LST UPCPICH------To check pilot channel power MOD UPCPICHPWR----To Change Pilot Channel Power in RNC. LST UINTRAFREQNCELL------Use this command to query the intra-frequency neighbori ng cell. ADD UINTRAFREQNCELL---- to add neighbour Cells (IntraFreq) LST UEXT3GCELL-----------List the information of neighboring RNC cells. ADD UEXT3GCELL----To Add the 3G cells(Other Vendors) as external cells. ADD UEXT2GCELL----To Add the 2g Cells As external Cells ADD U2GNCELL------To add the 2G Neighbour Cells dsp usrnum----Hsdpa Throughput per subrack LST PHBMAP---To Check the Service Priority To Change the Node-B Name in RNC: 1.MOD UNODEBNAME 2.MOD ADJNODE To Change the Node-B Name in Node-B end 1.MOD SITE 2.SET NODEBNAME LST DEVIP----To check the RNC Board IP. LST ETHIP----To Check the Ethernet port IP. LST ALMAF----To check the RNC Alarm DSP E1T1---To check the E1T1 of Site in RNC end. LST VER---To check the Software Version of RNC. DSP OMU----To check the OMU Status in RNC. DSP OMUHW---To check the Status of ETH port. LST License---To check the License file loaded in RNC & Active license. DSP LICUSAGE---To check the feature activated in the License. LST UCELLHSDPA----To check whether the HSDPA feature is Activated or Not. LST UCELLHSUPA----To check whether the HSUPA feature is Actiavted or not DSP ELABEL:to Check the item Code of Boards LST UAC----To Check the LAC & RAC. MOD UCELLLACINFO----To Change LAC,RAc,SAC for Cell. Node-B REQ CMCTRL----request CM control for an LMT user FOC CMCTRL-----to forcibly obtain the NE Configuration Management (CM) control w
hen the M2000 retains CM control after obtaining it.
LST DEVIP----To Check what are the IP defined in Node-B RST BRD---to reset the board RST NODEB---To reset the whole node-B BLK BRD--to block board BLK LOCELL---To block CELL. DSP VSWR----to check VSWR. ADD DEVIP---to add the Devip in Node-B ADD IPRT---- To add the Iproute in node-B. LST RRU----to Check the RRU Number,RRU work Standard LST RRUCHAIN----- To Check the Chain Number,WBBP board Subrack no,Slot Number. MoD LOCELL-----to Change the Frequecy number,transmitting power. LST LOCELL----to check the Local cell id,Cell ID. LST SEC--to Check the Sector Type LST RXBRANCH---To check the Attenuation MOD RXBRANCH----To Modify the attenuation. LST ALMAF-------To check the Alarm in Node-B end. LST VER-------To check the Software version. LST NODEBNAME---To check the Correct Configuration file is loaded or not,Nodeb N ame normally will be the Site Name. PING---To do ping test in Node-B end. TRACERT---To Check,is there any drop in IP(Useful to check transmission having p roblem) LST IPCLKLNK---To check the IPClock IP address. DSP IPCLKLNK---to Check the Status of IPCLK. LST ALMPort---To check the External Alarm Configuration. SET ALMPort---to Define the External Alarm in Node-B end. SET ENVALMPARA----To define the External Alarm Name. LST ETHPORT -------To check the ETHport Configurtion SET ETHPORT-------To Configure the ETHport DSP TIME-----To check the Current time in Node-B SET TIME----To Set the Correct time DSP LICENSE----To check License is loaded or not. DSP CELLCFG----To check the Scrambling code (PSC) ULD File-------To upload the Log File DSP SFP---to Check the SFP module type & output power Site Down Alarm NCP,CCP Alarm SCTP,SAALNK. NodeB Unavailable Sector Down: Locell unusable. Cell Setup Failed
Computer Networking: The Complete Beginner's Guide to Learning the Basics of Network Security, Computer Architecture, Wireless Technology and Communications Systems (Including Cisco, CCENT, and CCNA)
Evaluation of Some Websites that Offer Virtual Phone Numbers for SMS Reception and Websites to Obtain Virtual Debit/Credit Cards for Online Accounts Verifications