Professional Documents
Culture Documents
Quick Operation Guide of DS-7200&7300&8100-SH Series DVR - V2.2.3
Quick Operation Guide of DS-7200&7300&8100-SH Series DVR - V2.2.3
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact
dealer.
This manual is applicable to the following models:
DS-7204HVI-SH, DS-7208HVI-SH, DS-7216HVI-SH; DS-7204HFI-SH, DS-7208HFI-SH, DS-7216HFI-SH;
DS-7204HWI-SH, DS-7208HWI-SH, DS-7216HWI-SH; DS-7204HVI-SV, DS-7208HVI-SV, DS-7216HVI-SV;
DS-7304HFI-SH, DS-7308HFI-SH, DS-7316HFI-SH, DS-7324HFI-SH, DS-7332HFI-SH; DS-7304HWI-SH,
DS-7308HWI-SH, DS-7316HWI-SH, DS-7324HWI-SH, DS-7332HWI-SH; DS-7324HI-SH, DS-7332HI-SH;
DS-8124HCI-SH, DS-8132HCI-SH; DS-8124HFSI-SH, DS-8132HFSI-SH; DS-8124HWSI-SH,
DS-8132HWSI-SH.
DVR Pre-Installation
This Series DVR is highly advanced surveillance equipment that should be installed with care. Please take into
consideration the following precautionary steps before installation of the DVR.
1. Keep all liquids away from the DVR.
2. Install the DVR in a well-ventilated and dust-free area.
3. Ensure environmental conditions meet factory specifications.
4. Install a manufacturer recommended HDD.
DVR Installation
During the installation of the DVR:
1.
2.
3.
4.
5.
6.
7.
8.
2. Install the HDD in the HDD rack using the provided screws. Fasten the screws on the
bottom to fix the HDD.
1
3. Connect the HDD to the motherboard of the DVR with the included data cable.
2. Install the HDD to the HDD rack using the provided screws, and then fasten the screws to fix the HDD.
3. Connect one end of the data cable to the motherboard of DVR and the other end to the HDD.
Front Panel
DS-7200-SH/SV:
The front panel of DS-7200-SH/SV is shown below:
Name
Function Description
POWER
STATUS
STATUS indicator lights in red when data is being read from or written to HDD.
Tx/Rx
USB Interface
IR Receiver
DS-7300-SH:
The front panel of DS-7300-SH is shown below:
Name
POWER ON/OFF
IR Receiver
USB
DVD-ROM
POWER
READY
STATUS
ALARM
HDD
Function Description
Power on/off switch.
Receiver for IR remote control.
Connect to USB mouse or USB flash memory devices.
Slot for DVD-ROM.
Power indicator lights in green when DVR is powered up.
Ready indicator is normally green, indicating that the DVR is functioning properly.
Indicator turns green when DVR is controlled by an IR remote control with the
address from 1~254;
Indicator turns red when the SHIFT button is used;
Indicator does not light when the DVR is controlled by a keyboard or by the IR
remote control with the address of 255;
Indicator turns green when the DVR is controlled by IR remote control (with the
address from 1~254) and keyboard at the same time , and the SHIFT button is not
used;
Indicator turns orange : (a) when the DVR is controlled by IR remote control (with
the address from 1~254) and keyboard at the same time and the SHIFT button is used
as well; (b) when the DVR is controlled by IR remote control (with the address from
1~254) and the SHIFT button is used.
Alarm indicator turns red when a sensor alarm is detected.
HDD indicator blinks in red when data is being read from or written to HDD.
Tx/Rx
1/MENU
2ABC/F1
3DEF/F2
4GHI/ESC
5JKL/EDIT
6
SHIFT
6MNO/PLAY
7PQRS/REC
8TUV/PTZ
9WXYZ/PREV
0/A
DIRECTION
ENTER
JOG SHUTTLE
Control
DS-8100-SH:
The front panel of DS-8100-SH is shown below:
1
2
10
Name
POWER ON/OFF
IR Receiver
USB
DVD-ROM
ALARM
READY
STATUS
5
HDD
TX/RX
GUARD
Function Description
Power on/off switch.
Receiver for IR remote control.
Connect to USB mouse or USB flash memory devices.
Slot for DVD-ROM.
Alarm indicator turns red when a sensor alarm is detected.
Ready indicator is normally blue, indicating that the DVR is functioning properly.
Indicator turns blue when DVR is controlled by an IR remote.
Indicator turns red when controlled by a keyboard and orange when IR remote and
keyboard is used at the same time.
Indicator does not light when the DVR is controlled by the IR remote control with
the address of 255.
HDD indicator blinks in red when data is being read from or written to HDD.
TX/RX indictor blinks in blue when network connection is functioning properly.
Indicator turns blue when the device is armed;
Indicator does not light when the device is disarmed;
The arm/disarm state can be initiated by pressing and holding on the ESC button
for more than 3 seconds in live view mode.
The button lights in blue when the corresponding channel is recording; it is red
when the channel is in network transmission status; it is pink when the channel is
recording and transmitting.
Channel Status
LED Indicators
Alphanumeric
Buttons
ESC
REC/SHOT
PLAY/AUTO
8
ZOOM+ Button
In PTZ control mode, the ZOOM+ button is used to zoom in the PTZ camera.
A/FOCUS+
EDIT/IRIS+
MENU/WIPER
F1/LIGHT
F2/AUX
MAIN/SPOT/ZO
OM-
PREV/FOCUSPTZ/IRIS-
DIRECTION
ENTER
10
JOG SHUTTLE
Control
Rear Panel
DS-7204HVI/HFI/HWI-SH and DS-7204HVI-SV:
11
10
12
Note: The rear panels of DS-7208HVI-SH and DS-7208HVI-SV provide 8 video input interfaces.
11
10
12
Note: The rear panels of DS-7208HFI-SH and DS-7208HWI-SH provide 8 video input interfaces.
Item
Description
VIDEO IN
VIDEO OUT
USB Interface
HDMI
VGA
DB15 connector for VGA output. Display local video output and menu.
AUDIO IN
AUDIO OUT
LAN Interface
RS-485 Interface
10
12V
11
POWER
12
GND
11
12
13
10
14
15
12
10
11
13
14
13
14
15
10
11
12 15
Item
Description
VIDEO IN
MAIN VIDEO OUT
4
5
USB Interface
RS-232
6
7
VGA
AUDIO IN
DB15 connector for VGA output. Display local video output and menu.
RCA connector for audio input.
8
9
AUDIO OUT
LAN Interface
RS-485 Interface
10
KB
11
12
Alarm In/Out
eSATA
13
14
110~240VAC
POWER
15
GND
10 11 12
13
14 15 16
17
Note: DS-7324HFI-SH, DS-7324HWI-SH and DS-7324HI-SH models provide 24 video input interfaces on the
rear panel.
Item
Description
VIDEO IN
RCA connector for audio output. This connector is synchronized with CVBS
video output.
RCA connector for audio output. This connector is synchronized with VGA
video output.
LINE IN
AUDIO IN
VGA
DB15 connector for VGA output. Display local video output and menu.
HDMI
USB Interface
LAN Interface
10
RS-232
11
Termination Switch
RS-485 Interface
12
KB
13
Alarm In/Out
14
eSATA
15
GND
16
110~240VAC
17
POWER
10
8 9
10 11 12 13 14
15
16 17
18
Note: DS-8124HCI-SH, DS-8124HFSI-SH and DS-8124HWSI-SH models provide 24 video input interfaces on
the rear panel.
Item
Description
VIDEO IN
LINE IN
AUDIO IN (1-4)
AUDIO IN (5-16)
VGA
DB15 connector for VGA output. Display local video output and menu.
RS-232
HDMI
10
USB Interface
11
LAN1/LAN2 Interface
12
eSATA
13
Termination Switch
RS-485 Interface
14
KB
15
Alarm In/Out
16
GND
17
110~240VAC
18
POWER
11
Peripheral Connections
Note: Alarm input/output connections are valid for the DS-7300-SH and DS-8100-SH models only.
For DC load, JP4 can be used within the limit of 12V/1A safely. If the interface is connected to an AC load, JP4
should be left open. Use an external relay for safety (as shown in the figure above).
There are 4 jumpers (JP4, JP5, JP6, and JP7) on the motherboard, each corresponding with one alarm output. By
default, jumpers are connected. To connect an AC load, jumpers should be removed.
Note: An external relay is needed to prevent electric shock when connecting to an AC load.
Alarm Connection
To connect alarm devices to the DVR:
1. Disconnect pluggable block from the ALARM IN /ALARM OUT terminal block.
2. Press and hold the orange part of the pluggable block; insert signal cables into slots and release the orange part.
Ensure signal cables are in tight.
3. Connect pluggable block back into terminal block.
RS-485 Connections
To connect RS-485 devices (e.g., pan/tilt unit) to the DVR:
Press and hold the orange part of the pluggable block; insert signal cables into slots and release the orange part.
Ensure signal cables are in tight.
Note: Make sure the pan/tilt receiver unit is connected to the D+ and D- of the RS-485 terminal of
DS-7200-SH/SV and DS-7304/7308/7316-SH DVR, or to the T+ and T- of the RS-485 terminal of
DS-7324/7332-SH and DS-8124/8132-SH DVR.
12
Specifications
Table 8 Specifications for DS-7200HFI-SH
Model
Video/Audio
input
DS-7204HFI-SH
Hard disk
External
interface
DS-7216HFI-SH
8-ch
16-ch
Video compression
H.264
Video input
4-ch
Audio compression
G.711
Audio input
HDMI/VGA output
Video/Audio
output
DS-7208HFI-SH
CVBS output
1-ch, resolution:
1080P:
19201080/60Hz
1-ch, resolution:
UXGA:
1080P: 19201080/60Hz,
16001200/60Hz
SXGA: 12801024/60Hz,
SXGA:
720P: 1280720/60Hz,
12801024/60Hz
XGA: 1024768/60Hz
720P: 1280720/60Hz
XGA: 1024768/60Hz
1-ch, BNC (1.0 Vp-p, 75 ),
resolution: PAL: 704 576, NTSC: 704 480
Encoding resolution
Frame rate
Audio output
64 Kbps
Dual-stream
Stream type
Synchronous
playback
4-ch
8-ch
16-ch
SATA
1 SATA interface
2 SATA interfaces
2 SATA interfaces
Capacity
Up to 4TB capacity
Network interface
Serial interface
USB interface
2, USB 2.0
Power supply
12 VDC
Consumption
(without HDD or
DVD-R/W)
Working
temperature
10 W
15 W
20 W
-10 C ~+55 C
Working humidity
10% ~ 90%
Chassis
Standalone 1U chassis
19-inch
rack-mounted 1U
chassis
19-inch
rack-mounted 1U
chassis
315 230 45 mm
445 290 45 mm
445 290 45 mm
2 kg
4 kg
4 kg
General
Dimensions
(W D H)
Weight
(without HDD or
DVD-R/W)
13
Video/Audio
input
DS-7204HVI-SH
16-ch
Video input
4-ch
Video input
interface
Audio
compression
Audio input
Two-way audio
input
Encoding
resolution
Frame rate
Mode1:
4CIF / 2CIF @ 15 fps or
CIF / QCIF @ 25 fps (P) /
30 fps (N)
Mode2:
Channel 1: 4CIF / 2CIF /
CIF / QCIF @ 25 fps (P) /
30 fps (N),
Channel 2~4: CIF / QCIF
@ 25 fps (P) / 30 fps (N)
Audio output
64 Kbps
Support;
Sub-stream: CIF @ 6 fps, QCIF @ 25 fps (P) /30 fps (N)
Video, Video & Audio
Video/Audio
output
Dual-stream
Stream type
General
8-ch
H.264
CVBS output
External
interface
DS-7216HVI-SH
Video
compression
HDMI/VGA
output
Hard disk
DS-7208HVI-SH
Synchronous
playback
4-ch
SATA
1 SATA interface
Capacity
Network
interface
Serial interface
USB interface
Up to 4TB capacity
Power supply
Consumption
(without HDD or
DVD-R/W)
Working
temperature
Working
humidity
Chassis
Dimensions
(W D H)
Weight (without
HDD or
DVD-R/W)
12 VDC
Mode1:
4CIF / 2CIF @ 15 fps
or CIF / QCIF @ 25
fps (P) / 30 fps (N)
Mode2:
Channel 1& Channel
5: 4CIF / 2CIF / CIF /
QCIF @ 25 fps (P) /
30 fps (N),
Other Channels: CIF /
QCIF @ 25 fps (P) /
30 fps (N)
8-ch
Mode1:
4CIF / 2CIF @ 6fps
or CIF / QCIF @ 25
fps (P) / 30 fps (N)
Mode2:
Channel 1: 4CIF /
2CIF / CIF / QCIF
@ 25 fps (P) / 30
fps (N),
Channel 2~16: CIF
/ QCIF @ 25 fps
(P) / 30 fps (N)
16-ch
10 W
10 W
15 W
4 kg
4 kg
-10 C ~+55 C
10% ~ 90%
Standalone 1U chassis
315 230 45 mm
2 kg
14
Video/Audio
input
DS-7204HVI-SV
DS-7208HVI-SV
DS-7216HVI-SV
8-ch
16-ch
Video
compression
H.264
Video input
4-ch
Video input
interface
Audio
compression
Audio input
Two-way audio
input
HDMI/VGA
output
CVBS output
G.711
1-ch, resolution:
1080P: 19201080/60Hz; SXGA: 12801024/60Hz;
720P: 1280720/60Hz; XGA: 1024768/60Hz
1-ch, BNC (1.0 Vp-p, 75 ),
resolution: PAL: 704 576, NTSC: 704 480
Encoding
resolution
Frame rate
Audio output
64 Kbps
Dual-stream
Stream type
Synchronous
playback
4-ch
SATA
1 SATA interface
Capacity
Up to 4TB capacity
Network
interface
Serial interface
USB interface
2, USB 2.0
Power supply
12 VDC
Video/Audio
output
8-ch
16-ch
Hard disk
External
interface
General
Consumption
(without HDD or
DVD-R/W)
Working
temperature
Working
humidity
Chassis
Dimensions
(W D H)
Weight (without
HDD or
DVD-R/W)
10 W
10 W
-10 C ~+55 C
10% ~ 90%
Standalone 1U chassis
315 230 45 mm
2 kg
15
15 W
Video/Audio
input
DS-7204HWI-SH
H.264
Video input
4-ch
Video input
interface
Audio
compression
Audio input
Two-way audio
input
HDMI/VGA
output
CVBS output
Video/Audio
output
DS-7208HWI-SH
Video
compression
8-ch
DS-7216HWI-SH
16-ch
G.711
1-ch, resolution:
1080P: 19201080/60Hz; SXGA: 12801024/60Hz;
720P: 1280720/60Hz; XGA: 1024768/60Hz
1-ch, BNC (1.0 Vp-p, 75 ),
resolution: PAL: 704 576, NTSC: 704 480
Encoding
resolution
Frame rate
Audio output
64 Kbps
Dual-stream
Stream type
Synchronous
playback
4-ch
8-ch
SATA
1 SATA interface
2 SATA interfaces
Capacity
Network
interface
Serial interface
USB interface
2, USB 2.0
Power supply
12 VDC
16-ch
Hard disk
External
interface
General
Consumption
(without hard
disk or
DVD-R/W)
Working
temperature
Working
humidity
Chassis
Dimensions
(W D H)
Weight (without
hard disk or
DVD-R/W)
10 W
15 W
20 W
-10 C ~+55 C
10% ~ 90%
Standalone 1U chassis
315 230 45 mm
2 kg
4 kg
16
4 kg
Model
Video/Audio
input
8-ch
16-ch
24-ch
32-ch
4-ch
Audio input
Two-way audio
input
Encoding resolution
1-ch, resolution:
1080P: 19201080/60Hz, SXGA: 12801024/60Hz,
720P: 1280720/60Hz, XGA: 1024768/60Hz
1-ch, BNC (1.0 Vp-p, 75 ),
resolution: PAL: 704 576, NTSC: 704 480
1-ch, BNC (1.0 Vp-p, 75 ),
resolution: PAL: 704 576, NTSC: 704 480
4CIF / 2CIF / CIF / QCIF
Frame rate
Audio output
64 Kbps
Dual-stream
Stream type
Synchronous
playback
SATA
4-ch
8-ch
16-ch
4 SATA interfaces
eSATA
1 eSATA interface
Capacity
Up to 4TB capacity
Network interface
1 RS-232,
RS-485(full-duplex),
Keyboard
USB interface
Alarm in
16
16
Alarm out
Power supply
Consumption
(without HDD or
DVD-R/W)
Working
temperature
Working humidity
40 W
Chassis
Serial interface
General
DS-7332
HFI-SH
Video input
Video input
interface
Audio compression
External
interface
DS-7324
HFI-SH
H.264
CVBS output
Hard disk
DS-7316
HFI-SH
Video compression
HDMI/VGA output
Video/Audio
output
DS-7308
HFI-SH
Dimensions
(W D H)
Weight
(without HDD or
DVD-R/W)
25 W
30 W
-10 C ~+55 C
10% ~ 90%
445 390 70 mm
5 kg
17
Model
Video/Audio
input
General
DS-7332
HWI-SH
8-ch
16-ch
24-ch
32-ch
Video input
4-ch
Audio compression
G.711u
Audio input
HDMI/VGA output
1-ch, resolution:
1080P: 19201080/60Hz, SXGA: 12801024/60Hz,
720P: 1280720/60Hz, XGA: 1024768/60Hz
CVBS output
Encoding resolution
Frame rate
Audio output
64 Kbps
Dual-stream
Synchronous playback
SATA
4 SATA interfaces
eSATA
1 eSATA interface
Capacity
Network interface
USB interface
Alarm in
16
16
Alarm out
Power supply
Consumption
(without HDD or
DVD-R/W)
Working temperature
40 W
Working humidity
10% ~ 90%
Chassis
Serial interface
External
interface
DS-7324
HWI-SH
H.264
Stream type
Hard disk
DS-7316
HWI-SH
Video compression
DS-7308
HWI-SH
Dimensions
(W D H)
Weight
(without HDD or
DVD-R/W)
25 W
30 W
-10 C ~+55 C
445 390 70 mm
5 kg
18
Video/Audio
input
DS-7324HI-SH
Video compression
H.264
Video input
24-ch
Audio compression
G.711u
Audio input
64 Kbps
Dual-stream
Synchronous playback
SATA
4 SATA interfaces
eSATA
1 eSATA interface
Capacity
Up to 4TB capacity
Network interface
Serial interface
USB interface
3 USB 2.0
Alarm in
16
Alarm out
Power supply
Consumption
(without HDD or
DVD-R/W)
Working temperature
Working humidity
10% ~ 90%
Chassis
CVBS output
Video spot out
Encoding resolution
Frame rate
Stream type
Hard disk
External
interface
General
32-ch
1-ch, resolution:
1080P: 19201080/60Hz, SXGA: 12801024/60Hz,
720P: 1280720/60Hz, XGA: 1024768/60Hz
1-ch, BNC (1.0 Vp-p, 75 ),
resolution: PAL: 704 576, NTSC: 704 480
1-ch, BNC (1.0 Vp-p, 75 ),
resolution: PAL: 704 576, NTSC: 704 480
WD1 / 4CIF / 2CIF / CIF / QCIF
WD1 / 4CIF: 15 fps
2CIF / CIF / QCIF: 25 fps (P) / 30 fps (N)
32 Kbps ~ 3072 Kbps, or user defined (Max. 3072 Kbps)
HDMI/VGA output
Video/Audio
output
DS-7332HI-SH
Dimensions
(W D H)
Weight (without HDD
or DVD-R/W)
40 W
-10C ~+55C
445 390 70 mm
5 kg
19
Video/Audio
input
DS-8124HCI-SH
Video compression
H.264
Video input
24-ch
Audio compression
G.711u
16-ch,
Audio 1-4: RCA (2.0 Vp-p, 1 k)
Audio 5-16: DB26 connector
1-ch, resolution:
1080P: 19201080/60Hz, SXGA: 12801024/60Hz,
720P: 1280720/60Hz, XGA: 1024768/60Hz
1-ch, BNC (1.0 Vp-p, 75 ),
resolution: PAL: 704 576, NTSC: 704 480
1-ch, BNC (1.0 Vp-p, 75 ),
resolution: PAL: 704 576, NTSC: 704 480
WD1 / 4CIF / 2CIF / CIF / QCIF
WD1 / 4CIF: 15fps
2CIF / CIF / QCIF: 25 fps (P) / 30 fps (N)
32 Kbps ~ 3072 Kbps, or user defined (Max. 3072 Kbps)
Audio output
64 Kbps
Dual-stream
Synchronous playback
SATA
8 SATA interfaces
eSATA
1 eSATA interface
Capacity
Up to 4TB capacity
Network interface
Serial interface
USB interface
3 USB 2.0
Alarm in
16
Alarm out
Power supply
Consumption
(without HDD or
DVD-R/W)
Working temperature
Working humidity
10% ~ 90%
Chassis
CVBS output
Video spot out
Encoding resolution
Frame rate
Stream type
Hard disk
External
interface
General
32-ch
Audio input
HDMI/VGA output
Video/Audio
output
DS-8132HCI-SH
Dimensions
(W D H)
Weight
(without HDD or
DVD-R/W)
40 W
-10 C ~+55 C
445 470 95 mm
8 kg
20
Video/Audio
DS-8124HFSI-SH
DS-8132HFSI-SH
Video compression
H.264
Video input
24-ch
Audio compression
G.711u
input
32-ch
16-ch,
Audio input
HDMI/VGA output
CVBS output
Video spot out
Video/Audio
output
External
interface
Encoding resolution
Frame rate
Audio output
64 Kbps
Dual-stream
Stream type
Hard disk
Synchronous playback
16-ch
SATA
8 SATA interfaces
eSATA
1 eSATA interface
Capacity
Up to 4TB capacity
Network interface
Serial interface
USB interface
3 USB 2.0
Alarm in
16
Alarm out
Power supply
Consumption
(without HDD or
40 W
DVD-R/W)
General
Working temperature
-10 C ~+55 C
Working humidity
10% ~ 90%
Chassis
Dimensions
(W D H)
Weight (without HDD or
DVD-R/W)
445 470 95 mm
8 kg
21
Video/Audio
DS-8124HWSI-SH
DS-8132HWSI-SH
Video compression
H.264
Video input
24-ch
Audio compression
G.711u
input
32-ch
16-ch,
Audio input
HDMI/VGA output
CVBS output
Video spot out
Video/Audio
output
External
interface
Encoding resolution
Frame rate
Audio output
64 Kbps
Dual-stream
Stream type
Hard disk
Synchronous playback
16-ch
SATA
8 SATA interfaces
eSATA
1 eSATA interface
Capacity
Up to 4TB capacity
Network interface
Serial interface
USB interface
3 USB 2.0
Alarm in
16
Alarm out
Power supply
Consumption
(without HDD or
40 W
DVD-R/W)
General
Working temperature
-10 C ~+55 C
Working humidity
10% ~ 90%
Chassis
Dimensions
(W D H)
445 470 95 mm
Weight
(without HDD or
8 kg
DVD-R/W)
22
Bit Rate
96K
128K
160K
192K
224K
256K
320K
384K
448K
512K
640K
768K
896K
1024K
1280K
1536K
1792K
2048K
3072Kbps
Storage Used
42M
56M
70M
84M
98M
112M
140M
168M
196M
225M
281M
337M
393M
450M
562M
675M
787M
900M
1350M
Note: Please note that supplied values for storage space used is just for reference. Storage space used is estimated
by formulas and may have some deviation from actual value.
23
Menu Operation
Menu Structure
The menu structure of the DS-7200-SH/SV series DVR is shown as below:
Menu
Playback
Export
Manual
Normal
Normal
Record
Event
Event
Tag
HDD
Record
Camera
Configuration
Maintenance
Shutdown
General
Schedule
OSD
General
System Info
Logout
Lock
Advanced
Encoding
Image
Network
Log Information
HDD Detect
Advanced
PTZ
Live View
Import/Export
Holiday
Motion
Exceptions
Upgrade
Privacy Mask
User
Default
Shutdown
Reboot
Net Detect
Tamper-proof
Video Loss
The menu structure of the DS-7300-SH and DS-8100-SH series DVR is shown as below:
Menu
Playback
Export
Manual
HDD
Record
Normal
Normal
Event
Event
Record
General
Alarm
Tag
Camera
Configuration
Schedule
OSD
General
System Info
Advanced
Encoding
Image
Network
Log Information
HDD Detect
Advanced
PTZ
Alarm
Import/Export
Holiday
Motion
RS-232
Upgrade
Privacy Mask
Live View
Default
Tamper-proof
Exceptions
Net Detect
Video Loss
User
Maintenance
Shutdown
Logout
Lock
Shutdown
Reboot
24
3. Click the Yes button. The following message box pops up:
25
Note: For the DS-7324/7332-SH and DS-8124/8132-SH models, when the resolution is set to 1024768 or
1280720, up to 16-division window display is supported in live view; when the resolution is set to
12801024, up to 25-division window display is supported; and when the resolution is set to 19201080, up
to 36-division window display is supported. By default, the system resolution is set to 12801024.
2. Check the checkbox to enable Setup Wizard when device starts. Click Next to continue the setup wizard.
You can also click Cancel to exit the Setup Wizard, or use the Setup Wizard next time by leaving the Start
wizard when device starts? checkbox checked and exit.
3. Click Next button on the Wizard window to enter the Login window.
1)
2)
To change the admin password, check the New Admin Password checkbox. Enter the new password
and confirm the password in the given fields.
4. Click the Next button to enter the Date and Time settings window.
Set the time zone, date format, system date and system time.
26
5. Click Next button which takes you back to the Network Setup Wizard window.
Set the network parameters, including the NIC type, IPv4 address, IPv4 subnet mask, default gateway, etc.
You can enable the DHCP to automatically obtain an IP address and other network settings from that server.
Note: The DS-7200-SH and DS-7200HVI-SV models provide one 10M/100Mbps self-adaptive network
interface, the DS-7300HWI/HFI-SH models provide one 10M/100M/1000Mbps self-adaptive network
interface, and the DS-8100-SH models provide two 10M/100M/1000Mbps self-adaptive network interfaces.
6. Click Next button to enter the HDD Management window.
To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD.
27
2)
3)
4)
Click Copy to copy the record settings of the current camera to other camera (s) if needed.
28
5)
8.
Live View
Some icons are provided on screen in Live View mode to indicate different camera status. These icons include:
Live View Icons
In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the
record and alarm in the channel, so that you can find problems as soon as possible.
Record (manual record, schedule record, motion detection record or alarm triggered record)
29
Description
Menu
Single Screen
Switch to the single full screen by choosing channel number from the dropdown list.
Multi-screen
Previous Screen
Next Screen
Start/Stop
Auto-switch
Note: The dwell time of the live view configuration must be set before using Start
Auto-switch.
Start Recording
Start all-day normal recording or motion detection recording for all channels.
Quick Set
All-day Playback
Aux Monitor
Switch to the auxiliary output mode and the operation for the main output is disabled.
Note: If you enter Aux monitor mode and the Aux monitor is not connected, the mouse
operation is disabled; you need to switch back to the Main output with the F1 button on
front panel or VOIP/MON button on IR remote control and then press the Enter button.
Note: If the corresponding camera supports intelligent function, the Reboot Intelligence option is included when
right-clicking mouse on this camera.
Use the mouse wheel to double-click on the HDMI/VGA output screen, and the following message box pops
up:
2.
Use the mouse wheel to double-click on the screen again to switch to the Aux output, or click Cancel to
cancel the operation.
3.
Select the Menu Output Mode to Main CVBS from the right-click menu on the CVBS output screen.
4.
On the pop-up message box, click Yes to restart the device to enable the CVBS output as the main output.
Note: You can select the Menu Output Mode under Menu>Configuration>More Settings to Auto or HDMI/VGA
and then restart the device to switch the main output back to HDMI/VGA output.
PTZ Control
Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done before
you set the PTZ camera.
Before you start, please check that the PTZ and the DVR are connected properly through RS-485 interface.
In the Live View mode, you can press the PTZ Control button on the IR remote control, or choose the PTZ
30
Control icon
Description
Description
Icon
Icon
Description
Zoom+, Focus+,
Iris+
Light on/off
Wiper on/off
3D-Zoom
Image
Centralization
Preset
Patrol
Pattern
Menu
Previous item
Next item
Start pattern/patrol
Minimize
windows
Exit
Record
You can use the right-click menu in live view mode to configure recording for all channels.
1. In the live view mode, use the mouse to right-click on the window to access the following menu:
2. Click the Start Recording submenu and select the recording mode to Normal Record or Motion Detection
Record.
31
3. In the pop-up message box, click Yes to finish the quick recording settings for all channels.
Note: The full-screen motion detection triggered recording is configured by default in this mode.
Playback
Play back the record files of a specific channel in the live view menu.
Note: Only record files recorded during the past five minutes on this channel will be played back.
32
Press PLAY button on the front panel or IR remote control to play back record files of the channel under
single-screen live view.
Under multi-screen live view, record files of the top left channel (not masked) will be played back.
2. Playback management.
The toolbar in the bottom part of Playback interface can be used to control playing process.
The channel and time selection menu will display by moving the mouse to the right of the playback interface.
Tick the channel or channels if you want to switch playback to another channel or execute simultaneous playback
of multiple channels.
33
Backup
Recorded files can be backed up to various devices, such as USB flash drives, USB HDDs or a DVD writer.
To export recorded files:
1. Click Menu>Export to enter Video Export interface.
Choose the channel (s) you want to back up and click the Quick Export button.
2. Enter Export interface, choose backup device and click Export button to start exporting.
34
to check it.
0202031030515
35
36